Occurrence and risk assessment of emerging contaminants in a water reclamation and ecological reuse project

Typical emerging contaminants in sewage treatment plant effluent, and related watersheds in the Pearl River Basin: Ecological risks and source identification

Emerging contaminants pose a potential risk to aquatic ecosystems in the Pearl River Basin, China, owing to the high population density and active industry. This study investigated samples from eight sewage treatment plants, and five surface water bodies of related watersheds. To screen the risk of emerging contaminants (ECs), and clarify their sources, this study calculated the risk quotient of detected chemical and performed source identification/apportionment using the positive matrix factorization method. In total, 149 organic pollutants were identified. Pharmaceuticals showed significant concentrations in sewage treatment plant samples (120.87 ng/L), compared with surface water samples (1.13 ng/L). The ecological risk assessment identified three chemicals with a heightened risk to aquatic organisms: fipronil sulfide, caffeine, and roxithromycin. Four principal sources of contaminants were identified: pharmaceutical wastewater, domestic sewage, medical effluent, and agricultural runoff. Pharmaceutical wastewater was the primary contributor (60.4 %), to the cumulative EC concentration and to ECs in sewage treatment plant effluent. Agricultural drainage was the main source of ECs in surface water. This study provides a strategy to obtain comprehensive information on the aquatic risks and potential sources of EC species in areas affected by artificial activities, which is of substantial importance to pollutant management and control.

Sustainable and ultrafast antibiotics removal, self-cleaning and disinfection with electroactive metal-organic frameworks/carbon nanotubes membrane

Although conventional nanofiltration (NF) membrane is widely applied in water treatment, it faces the challenges of insufficient selectivity toward emerging contaminants, low permeability and non-sustainable fouling control. Herein, a novel electroactive metal-organic frameworks/carbon nanotubes membrane was constructed by facile and green nanobubbles-mediated non-solvent-induced phase separation (NIPS) strategy for ultrafast antibiotics removal. It presented 3-fold to 100-fold higher permeability (101.3-105.7 L·h-1·m-2·bar-1) without compromising rejection (71.8 %-99.3 %) of common antibiotics (tetracycline, norfloxacin, sulfamethoxazole, sulfamethazine) than most commercial and state-of-the-art NF membranes. The separation mechanism was due to the synergy of loose selective layer with three-dimensional interconnected networks and UiO-66/CNTs with unique pore sieving and charge property. It also presented excellent antibiotics selectivity with high NaCl/tetracycline separation factor of 194 and CuCl2/tetracycline separation factor of 316 for remediation of antibiotics and heavy metal combined pollution. Meanwhile, it possessed efficient anti-fouling, antibacterial and electro-driven self-cleaning ability, which enabled sustainable fouling control and disinfection with short process, low energy and chemical consumption. Furthermore, potential application of UiO-66/CNTs membrane in wastewater reclamation was demonstrated by stable antibiotics rejection, efficient flux recovery and long-term stability over 260 h. This study would provide useful insights into removal of emerging contaminants from water by advanced NF membrane.

Comparative evaluation of SPE methods for biotoxicity assessment of water and wastewater: Linkage between chemical extracting efficiency and biotoxicity outcome

Biotoxicity assessment results of environmental waters largely depend on the sample extraction protocols that enrich pollutants to meet the effect-trigger thresholds of bioassays. However, more chemical mixture does not necessarily translate to higher combined biotoxicity. Thus, there is a need to establish the link between chemical extracting efficiency and biotoxicity outcome to standardize extraction methods for biotoxicity assessment of environmental waters. This study compares the performance of five different extraction phases in solid phase extraction (SPE), namely HLB, HLB+Coconut, C18 cartridge, C18 disk and Strata-X, and evaluated their chemical extracting efficiencies and biotoxicity outcomes. We quantitatively assessed cytotoxicity, acute toxicity, genotoxicity, estrogenic activity, and neurotoxicity of the extracts using in vitro bioassays and characterized the chemical extracting efficiencies of the SPE methods through chemical recoveries of 23 model compounds with different polarities and total organic carbon. Using Pareto ranking, we identified HLB+Coconut as the optimal SPE method, which exhibited the highest level of water sample biotoxicity and recovered the most chemicals in water samples. We found that the biotoxicity outcomes of the extracted water samples significantly and positively correlated with the chemical extracting efficiencies of the SPE methods. Moreover, we observed synchronous changing patterns in biotoxicity outcome and chemical extracting efficiencies in response to increasing sample volumes per cartridge (SVPC) during SPE. Our findings underscore that higher chemical extracting efficiency of SPE corresponds to higher biotoxicity outcome of environmental water samples, providing a scientific basis for standardization of SPE methods for adequate assessment of biotoxicities of environmental waters.

Potential for curdlan recovery from aerobic granular sludge wastewater treatment systems - A review

The aerobic granular sludge (AGS) biotechnology has been explored for wastewater treatment for over two decades. AGS is gaining increased interest due to its enhanced treatment performance ability and the potential for resource recovery from AGS-based wastewater treatment systems. Resource recovery from AGS is a promising approach to sustainable wastewater treatment and attaining a circular economy in the wastewater management industry. Currently, research is at an advanced stage on recovering value-added resources such as phosphorus, polyhydroxyalkanoates, alginate-like exopolysaccharides, and tryptophan from waste aerobic granules. Recently, other value-added resources, including curdlan, have been identified in the aerobic granule matrix, and this may increase the sustainability of biotechnology in the wastewater industry. This paper provides an overview of AGS resource recovery potential. In particular, the potential for enhanced curdlan biosynthesis in the granule matrix and its recovery from AGS wastewater treatment systems is outlined.

Occurrence, removal, and risk assessment of polycyclic aromatic hydrocarbons and their derivatives in typical wastewater treatment plants

Wastewater treatment plants (WWTPs) have a certain removal capacity for polycyclic aromatic hydrocarbons (PAHs) and their derivatives, but some of them are discharged with effluent into the environment, which can affect the environment. Therefore, to understand the presence, sources, and potential risks of PAHs and their derivatives in WWTPs. Sixteen PAHs, three chlorinated polycyclic aromatic hydrocarbons (ClPAHs), three oxidized polycyclic aromatic hydrocarbons (OPAHs), and three methylated polycyclic aromatic hydrocarbons (MPAHs) were detected in the influent and effluent water of three WWTPs in China. The average concentrations of their influent ∑PAHs, ∑ClPAHs, ∑OPAHs, and ∑MPAHs ranged from 2682.50 to 2774.53 ng/L, 553.26-906.28 ng/L, 415.40-731.56 ng/L, and 534.04-969.83 ng/L, respectively, and the effluent concentrations ranged from 823.28 to 993.37 ng/L, 269.43-489.94 ng/L, 285.93-463.55 ng/L, and 376.25-512.34 ng/L, respectively. The growth of heat transport and industrial energy consumption in the region has a significant impact on the level of PAHs in WWTPs. According to the calculated removal efficiencies of PAHs and their derivatives in the three WWTPs (A, B, and C), the removal rates of PAHs and their derivatives were 69-72%, 62-71%, and 68-73%, respectively, and for the substituted polycyclic aromatic hydrocarbons (SPAHs), the removal rates were 41-49%, 31-40%, and 33-39%, respectively; moreover, the removal rates of PAHs were greater than those of SPAHs in the WWTPs. The results obtained via the ratio method indicated that the main sources of PAHs in the influent of WWTPs were the combustion of coal and biomass, and petroleum contamination was the secondary source. In risk evaluation, there were 5 compounds for which the risk quotient was considered high ecological risk. During chronic disease evaluation, there were 11 compounds with a risk quotient considered to indicate high risk. PAHs and SPAHs with high relative molecular masses in the effluent of WWTPs pose more serious environmental hazards than their PAHs counterparts.

Alternating water sources to minimize contaminant accumulation in food plants from treated wastewater irrigation

The use of treated wastewater (TWW) for agricultural irrigation is a critical measure in advancing sustainable water management and agricultural production. However, TWW irrigation in agriculture serves as a conduit to introduce many contaminants of emerging concern (CECs) into the soil-plant-food continuum, posing potential environmental and human health risks. Currently, there are few practical options to mitigate the potential risk while promoting the safe reuse of TWW. In this greenhouse study, the accumulation of 11 commonly occurring CECs was evaluated in three vegetables (radish, lettuce, and tomato) subjected to two different irrigation schemes: whole-season irrigation with CEC-spiked water (FULL), and half-season irrigation with CEC-spiked water, followed by irrigation with clean water for the remaining season (HALF). Significant decreases (57.0-99.8 %, p < 0.05) in the accumulation of meprobamate, carbamazepine, PFBS, PFBA, and PFHxA in edible tissues were found for the HALF treatment with the alternating irrigation scheme. The CEC accumulation reduction was attributed to reduced chemical input, soil degradation, plant metabolism, and plant growth dilution. The structural equation modeling showed that this mitigation strategy was particularly effective for CECs with a high bioaccumulation potential and short half-life in soil, while less effective for those that are more persistent. The study findings demonstrate the effectiveness of this simple and on-farm applicable management strategy that can be used to minimize the potential contamination of food crops from the use of TWW and other marginal water sources in agriculture, while promoting safe reuse and contributing to environmental sustainability.

Bromine contamination and risk management in terrestrial and aquatic ecosystems

Bromine (Br) is widely distributed through the lithosphere and hydrosphere, and its chemistry in the environment is affected by natural processes and anthropogenic activities. While the chemistry of Br in the atmosphere has been comprehensively explored, there has never been an overview of the chemistry of Br in soil and aquatic systems. This review synthesizes current knowledge on the sources, geochemistry, health and environmental threats, remediation approaches, and regulatory guidelines pertaining to Br pollution in terrestrial and aquatic environments. Volcanic eruptions, geothermal streams, and seawater are the major natural sources of Br. In soils and sediments, Br undergoes natural cycling between organic and inorganic forms, with bromination reactions occurring both abiotically and through microbial activity. For organisms, Br is a non-essential element; it is passively taken up by plant roots in the form of the Br- anion. Elevated Br- levels can limit plant growth on coastal soils of arid and semi-arid environments. Br is used in the chemical industry to manufacture pesticides, flame retardants, pharmaceuticals, and other products. Anthropogenic sources of organobromine contaminants in the environment are primarily wastewater treatment, fumigants, and flame retardants. When aqueous Br- reacts with oxidants in water treatment plants, it can generate brominated disinfection by-products (DBPs), and exposure to DBPs is linked to adverse human health effects including increased cancer risk. Br- can be removed from aquatic systems using adsorbents, and amelioration of soils containing excess Br- can be achieved by leaching, adding various amendments, or phytoremediation. Developing cost-effective methods for Br- removal from wastewater would help address the problem of toxic brominated DBPs. Other anthropogenic organobromines, such as polybrominated diphenyl ether (PBDE) flame retardants, are persistent, toxic, and bioaccumulative, posing a challenge in environmental remediation. Future research directives for managing Br pollution sustainably in various environmental settings are suggested here.

Occurrence, bioaccumulation, fate, and risk assessment of emerging pollutants in aquatic environments: A review

Significant concerns on a global scale have been raised in response to the potential adverse impacts of emerging pollutants (EPs) on aquatic creatures. We have carefully reviewed relevant research over the past 10 years. The study focuses on five typical EPs: pharmaceuticals and personal care products (PPCPs), per- and polyfluoroalkyl substances (PFASs), drinking water disinfection byproducts (DBPs), brominated flame retardants (BFRs), and microplastics (MPs). The presence of EPs in the global aquatic environment is source-dependent, with wastewater treatment plants being the main source of EPs. Multiple studies have consistently shown that the final destination of most EPs in the water environment is sludge and sediment. Simultaneously, a number of EPs, such as PFASs, MPs, and BFRs, have long-term environmental transport potential. Some EPs exhibit notable tendencies towards bioaccumulation and biomagnification, while others pose challenges in terms of their degradation within both biological and abiotic treatment processes. The results showed that, in most cases, the ecological risk of EPs in aquatic environments was low, possibly due to potential dilution and degradation. Future research topics should include adding EPs detection items for the aquatic environment, combining pollution, and updating prediction models.

Emerging Contaminants in the Effluent of Wastewater Should Be Regulated: Which and to What Extent?

Effluent discharged from urban wastewater treatment plants (WWTPs) is a major source of emerging contaminants (ECs) requiring effective regulation. To this end, we collected discharge datasets of pharmaceuticals (PHACs) and endocrine-disrupting chemicals (EDCs), representing two primary categories of ECs, from Chinese WWTP effluent from 2012 to 2022 to establish an exposure database. Moreover, high-risk ECs' long-term water quality criteria (LWQC) were derived using the species sensitivity distribution (SSD) method. A total of 140 ECs (124 PHACs and 16 EDCs) were identified, with concentrations ranging from N.D. (not detected) to 706 μg/L. Most data were concentrated in coastal regions and Gansu, with high ecological risk observed in Gansu, Hebei, Shandong, Guangdong, and Hong Kong. Using the assessment factor (AF) method, 18 high-risk ECs requiring regulation were identified. However, only three of them, namely carbamazepine, ibuprofen, and bisphenol-A, met the derivation requirements of the SSD method. The LWQC for these three ECs were determined as 96.4, 1010, and 288 ng/L, respectively. Exposure data for carbamazepine and bisphenol-A surpassed their derived LWQC, indicating a need for heightened attention to these contaminants. This study elucidates the occurrence and risks of ECs in Chinese WWTPs and provides theoretical and data foundations for EC management in urban sewage facilities.

Southeast Asia's environmental challenges: emergence of new contaminants and advancements in testing methods

Emerging contaminants, including pharmaceuticals, personal care products, microplastics, and per- and poly-fluoroalkyl substances, pose a major threat to both ecosystems and human health in Southeast Asia. As this region undergoes rapid industrialization and urbanization, the increasing presence of unconventional pollutants in water bodies, soil, and various organisms has become an alarming concern. This review comprehensively examines the environmental challenges posed by emerging contaminants in Southeast Asia and recent progress in toxicity testing methods. We discuss the diverse range of emerging contaminants found in Southeast Asia, shedding light on their causes and effects on ecosystems, and emphasize the need for robust toxicological testing methods. This review is a valuable resource for researchers, policymakers, and environmental practitioners working to mitigate the impacts of emerging contaminants and secure a sustainable future for Southeast Asia.

Molecular insight of dissolved organic matter and chlorinated disinfection by-products in reclaimed water during chlorination with permanganate preoxidation

Permanganate is a common preoxidant applied in water treatment to remove organic pollutants and to reduce the formation of disinfection by-products. However, the effect of permanganate preoxidation on the transformation of dissolved effluent organic matter (dEfOM) and on the formation of unknown chlorinated disinfection by-products (Cl-DBPs) during chlorination remains unknown at molecular level. In this work, the molecular changes of dEfOM during permanganate preoxidation and subsequent chlorination were characterized using Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS). Permanganate preoxidation was found to decrease the DBE (double bond equivalent) and AImod (modified aromaticity index) of the dEfOM. The identity and fate of over 400 unknown Cl-DBPs during KMnO4-chlorine treatment were investigated. Most Cl-DBPs and the precursors were found to be highly unsaturated aliphatic and phenolic compounds. The Cl-DBPs precursors with lower H/C and lower O/C were preferentially removed by permanganate preoxidation. Additionally, permanganate preoxidation decreased the number of unknown Cl-DBPs by 30% and intensity of unknown Cl-DBPs by 25%. One-chlorine-containing DBPs were the major Cl-DBPs and had more CH2 groups and higher DBEw than Cl-DBPs containing two and three chlorine atoms. 60% of the Cl-DBPs formation was attributed to substitution reactions (i.e., +Cl-H, +2Cl-2H, +3Cl-3H, +ClO-H, +Cl2O3-2H). This work provides detailed molecular level information on the efficacy of permanganate preoxidation on the control of overall Cl-DBPs formation during chlorination.

Mapping of emerging contaminants in coastal waters research: A bibliometric analysis of research output during 1986-2022

This bibliometric analysis provides the first overview of the literature on emerging contaminants in coastal waters. Bibexcel, Microsoft Excel, VOSviewer and the bibliometix R package software were used for bibliometric analysis and science mapping. 556 publications, published between 1986 and 2022, were retrieved from the Web of Science (WoS) database. The results showed that this field of research follows Price's law of exponential growth and has exploded since 2001. Authors, journals and institutions followed Lotka's law, and Price's index (43.4 %) showed that the field is far from being obsolete. The most influential institution is the Chinese Academy of Sciences, while authors from China, USA, Japan and Singapore have the most publications and international co-authorships. The leading journal is Marine Pollution Bulletin, with a focus on Environmental Science WoS category. Hot research areas focus on risk assessment of PCBs, organochlorine compounds and personal care products in surface water and wastewater.

Simultaneous removal of pharmaceuticals and heavy metals from aqueous phase via adsorptive strategy: A critical review

The coexistence of pharmaceuticals and heavy metals is regarded as a serious threat to aquatic environments. Adsorbents have been widely applied to the simultaneous removal of pharmaceuticals and metals from aqueous phase. Through a comprehensive review, behaviors that promote, inhibit, or have no effect on simultaneous adsorption of pharmaceuticals and heavy metals were found to depend on the system of contaminants and adsorbents and their environmental conditions, such as: characteristics of adsorbent and pollutant, temperature, pH, inorganic ions, and natural organic matter. Bridging and competition effects are the main reasons for promoting and inhibiting adsorption in coexisting systems, respectively. The promotion is more significant in neutral or alkaline conditions. After simultaneous adsorption, a solvent elution approach was most commonly used for regeneration of saturated adsorbents. To conclude, this work could help to sort out the theoretical knowledge in this field, and may provide new insights into the prevention and control of pharmaceuticals and heavy metals coexisting in wastewater.

Typical organic contaminants in hair of adult residents between inland and coastal capital cities in China: Differences in levels and composition profiles, and potential impact factors

The growing of urbanization, industrialization, and agricultural production have resulted in the increasing contamination of typical organic contaminants (OCs) in China. However, data on differences in exposure characteristics of typical OCs between the coastal and inland cities among residents in China are limited. In this study, hair samples were collected from adult residents in 10 and 17 provincial capital cities in coastal and inland China, respectively, to investigate the differences in the levels and composition profiles of typical OCs. The potential factors impacting the human exposure to OCs were also examined based on the relationship among the hair OC levels and the population characteristics and statistical indicators. The median concentrations of dichlorodiphenyltrichloroethane's (DDTs), polybrominated diphenyl ethers (PBDEs), and organophosphorus flame retardants (PFRs) in hair of coastal urban residents were 3.64, 5.58, and 268 ng/g, respectively, while their concentrations in samples from inland urban residents were 1.84, 3.85, and 202 ng/g, respectively. Coastal residents showed significantly higher hair OC concentrations than inland residents (p < 0.05). BDE209 and p,p'-DDE were the predominant chemicals for PBDEs and DDTs, respectively, in both coastal and inland cities. Tris(2-chloroisopropyl) phosphate (TCIPP) was the dominant PFR in coastal residents' hair, while triphenyl phosphate (TPHP) was the major PFR in inland residents' hair, possibly owing to the different usages of the PFRs. Significant gender differences were observed in the levels and composition profiles of OCs (p < 0.05). The levels of p,p'-DDE and TCIPP were significantly related to the gross domestic product (GDP), gross secondary industry product, and the per capita consumption of aquatic products (p < 0.05). This study provides scientific data for evaluating human exposure to OCs in urban residents at a large scale and its associations with statistical indicators including urbanization, industrialization, agricultural production, and diet in China.

Indirect potable water reuse to face drought events in Barcelona city. Setting a monitoring procedure to protect aquatic ecosystems and to ensure a safe drinking water supply

The climate change and increasing anthropogenic pressures are expected to limit the availability of water resources. Hence, active measures must be planned in vulnerable regions to ensure a sustainable water supply and minimize environmental impacts. A pilot test was carried out in the Llobregat River (NE Spain) aiming to provide a useful procedure to cope with severe droughts through indirect water reuse. Reclaimed water was used to restore the minimum flow of the lower Llobregat River, ensuring a suitable water supply downstream for Barcelona. A monitoring was performed to assess chemical and microbiological threats throughout the water treatment train, the river and the final drinking water, including 376 micropollutants and common microbiological indicators. The effects of water disinfection were studied by chlorinating reclaimed water prior to its discharge into the river. Data showed that 10 micropollutants (bromodichloromethane, dibromochloromethane, chloroform, EDDP, diclofenac, iopamidol, ioprimid, lamotrigine, ofloxacin and valsartan) posed a potential risk to aquatic life, whereas one solvent (1,4-dioxane) could affect human health. The chlorination of reclaimed water mitigated the occurrence of pharmaceuticals but, conversely, the concentration of halogenated disinfection by-products increased. From a microbiological perspective, the microbial load decreased along wastewater treatments and, later, along drinking water treatment, ultimately reaching undetectable values in final potable water. Non-chlorinated reclaimed water showed a lower log reduction of E. coli and coliphages than chlorinated water. However, the effect of disinfection vanished once reclaimed water was discharged into the river, as the basal concentration of microorganisms in the Llobregat River was comparable to that of non-chlorinated reclaimed water. Overall, our study indicates that indirect water reuse can be a valid alternative source of drinking water in densely populated areas such as Barcelona (Catalonia - NE Spain). A suitable monitoring procedure is presented to assess the related risks to human health and the aquatic ecosystem.

Occurrence of OCPs & PCBs and their effects on multitrophic biological communities in riparian groundwater of the Beiluo River, China

Persistent Organic Pollutants (POPs) may exert adverse effects on human and ecosystem health. However, as an ecologically fragile zone with strong interaction between river and groundwater, the POPs pollution in the riparian zone has received little attention. The goal of this research is to examine the concentrations, spatial distribution, potential ecological risks, and biological effects of organochlorine pesticides (OCPs) and polychlorinated biphenyls (PCBs) in the riparian groundwater of the Beiluo River, China. The results showed that the pollution level and ecological risk of OCPs in riparian groundwater of the Beiluo River were higher than PCBs. The presence of PCBs (Penta-CBs, Hexa-CBs) and CHLs, respectively, may have reduced the richness of bacteria (Firmicutes) and fungi (Ascomycota). Furthermore, the richness and Shannon's diversity index of algae (Chrysophyceae and Bacillariophyta) decreased, which could be linked to the presence of OCPs (DDTs, CHLs, DRINs), and PCBs (Penta-CBs, Hepta-CBs), while for metazoans (Arthropoda) the tendency was reversed, presumably as a result of SULPHs pollution. In the network analysis, core species belonging to bacteria (Proteobacteria), fungi (Ascomycota), and algae (Bacillariophyta) played essential roles in maintaining community function. Burkholderiaceae and Bradyrhizobium can be considered biological indicators of PCBs pollution in the Beiluo River. Note that the core species of interaction network, playing a fundamental role in community interactions, are strongly affected by POPs pollutants. This work provides insights into the functions of multitrophic biological communities in maintaining the stability of riparian ecosystems through the response of core species to riparian groundwater POPs contamination.

Multiclass target analysis of contaminants of emerging concern including transformation products, soil bioavailability assessment and retrospective screening as tools to evaluate risks associated with reclaimed water reuse

The occurrence of 200 multiclass contaminants of emerging concern (CECs) encompassing 168 medicinal products and transformation products (TPs), 5 artificial sweeteners, 12 industrial chemicals, and 15 other compounds was investigated in influent and effluent wastewater samples collected during 7 consecutive days from 5 wastewater treatment plants (WWTPs) located in Cyprus. The methodology included a generic solid-phase extraction protocol using mixed-bed cartridges followed by Ultra-High Performance Liquid Chromatography coupled with Quadrupole-Time of Flight Mass Spectrometry (UHPLC-QTOF-MS) analysis. A total of 63 CECs were detected at least in one sample, with 52 and 55 out of the 200 compounds detected in influents and effluents, respectively. Ten (10) out of the 24 families of parent compounds and associated TPs were found in the wastewater samples (influent or effluent). 1-H-benzotriazole, carbamazepine, citalopram, lamotrigine, sucralose, tramadol, and venlafaxine (>80 % frequency of appearance in effluents) were assessed with respect to their bioavailability in soil as part of different scenarios of irrigation with reclaimed water following a qualitative approach. A high score of 12 (high probability) was predicted for 2 scenarios, a low score of 3 (rare occasions) for 2 scenarios, while the rest 28 scenarios had scores 5-8 (unlikely or limited possibility) and 9-11 (possibly). Retrospective screening was performed with the use of a target database of 2466 compounds and led to the detection of 158 additional compounds (medicinal products (65), medicinal products TPs (15), illicit drugs (7), illicit drugs TPs (3), industrial chemicals (11), plant protection products (25), plant protection products TPs (10), and various other compounds (22). This work aspires to showcase how the presence of CECs in wastewater could be investigated and assessed at WWTP level, including an expert-based methodology for assessing the soil bioavailability of CECs, with the aim to develop sustainable practices and enhance reclaimed water reuse.

Loosely Sandwich-Structured Membranes Decorated with UiO-66-NH2 for Efficient Antibiotic Separation and Organic Solvent Resistance

Thin-film nanocomposite (TFN) membranes with efficient molecular separation and organic solvent resistance are active in demand in wastewater treatment and resource reclamation, meeting the goal of emission peaks and carbon neutrality. In this work, a simple and rational design strategy has been employed to construct a sandwich-structured membrane for removing fluoroquinolone antibiotics and recycling organic solvents. The sandwich-structured membrane is composed of a porous substrate, a hydrophilic tannic acid-polyethyleneimine (TA-PEI) interlayer, and a polyamide (PA) selective layer decorated with metal-organic framework (PA-MOF). Results manifest that the hydrophilic TA-PEI interlayer played a bridging and gutter effect to achieve effective control in amide storage, amine diffusion, and nanomaterial downward leakage at the immiscible interface. The PA-MOF selective layer has been changed to a loosely crumpled surface, endowing functionalities on the sandwich-structured membrane that included limited pores, strengthened electronegativity, and stronger hydrophilicity. Thus, an enhanced water flux of 87.23 ± 7.43 LMH was achieved by the TFN-2 membrane (0.04 mg·mL^-1 UiO-66-NH₂), which is more than five times that of the thin-film composite membrane (17.46 ± 3.88 LMH). The rejection against norfloxacin, ciprofloxacin, and levofloxacin is 92.94 ± 1.60%, 94.62 ± 1.29%, and 96.92 ± 1.05%, respectively, effectively breaking through the "trade-off" effect between membrane permeability and rejection efficiency. Further antifouling results showed that the sandwich-structured membrane had lower flux decay ratios (3.36∼7.07%) and higher flux recovery ratios (93.40∼98.40%), as well as superior long-term stability after 30 days of filtration. Moreover, organic solvent resistance testing confirms that the sandwich-structured membrane maintained stable solvent flux and better recovery rates in ethanol, acetone, isopropanol, and N,N-dimethylformamide. Detailed nanofiltration mechanism studies revealed that these outstanding performances are based on the joint effect of the TA-PEI interlayer and PA-MOF selective layer, proposing a new perspective to break through the bottleneck of nanofiltration application in a complex environment.

Preparation of Copper-Decorated Activated Carbon Derived from Platamus occidentalis Tree Fiber for Antimicrobial Applications

This study focuses on a greener approach to synthesizing activated carbon by carbonizing Platamus occidentalis tree fibers (TFSA) with 98% H₂SO₄ at 100 °C. The resulted TFSA was employed as an effective adsorbent for copper ions in aqueous media, yielding copper decorated TFSA (Cu@TFSA). The successful adsorption of copper onto the TFSA was proven through extensive characterization techniques. Herein, the TEM and XPS showed that copper nanoparticles were formed in situ on the TFSA surface, without the use of additional reducing and stabilizing agents nor thermal treatment. The surface areas of TFSA and Cu@TFSA were 0.0150 m²/g and 0.3109 m²/g, respectively. Applying the Cu@TFSA as an antimicrobial agent against Escherica coli ( E. coli) and Salmonella resulted in the potential mitigation of complex secondary pollutants from water and wastewater. The Cu@TFSA exhibited outstanding antimicrobial activity against E. coli and Salmonella in both synthetic and raw water samples. This demonstrated a complete growth inhibition observed within 120 min of exposure. The bacteria inactivation took place through the destruction of the bacteria cell wall and was confirmed by the AFM analysis technique. Cu@TFSA has the potential to be used in the water and wastewater treatment sector as antimicrobial agents.

Effective adsorption of diclofenac and naproxen from water using fixed-bed column loaded with composite of heavy sugarcane ash and polyethylene terephthalate

The contamination of water by pharmaceutical pollutants is a major issue these days due to excessive use of these ingredients in modern life. This study evaluated the adsorption and effectiveness of a low-cost composite prepared from heavy sugarcane ash (HSA) fused with polyethylene terephthalate (PET) and functionalized with iron (Fe³⁺) in a dynamic system through a fixed-bed column. The solution of synthetic drugs was prepared and placed in a reservoir, using a peristaltic pump the solution is run onto the fixed bed column at a flow rate of 2 mL min^-1. Saturation time and adsorption capacity were evaluated by centrifugation and extraction after a regular interval of 2 h from the adsorption column. The samples were analyzed using high-performance liquid chromatography (HPLC) and the data was modeled for quantification. For DIC removal, an adsorption capacity of 324.34 μg. g^-1 and a saturation time of 22 h were observed, while the adsorption capacity of NAP was 956.49 μg. g^-1, with a saturation time of 8 h. Thus, the PETSCA/Fe³⁺ adsorbent proved to be quite efficient for removing the pharmaceutical pollutants, with a longer period of operation for DIC removal. These findings suggested that a highly efficient bed column made from a less expensive waste material and could be used to remove hazardous pharmaceutical contaminants.

Fabrication of Bi-Bi3O4Cl plasmon photocatalysts for removal of aqueous emerging contaminants under visible light

Photocatalytic oxidation of emerging contaminants (ECs) in water has recently gained extensive attentions. In this study, bismuth oxychloride-based plasmon photocatalysts (Bi-Bi₃O₄Cl) exhibiting high performance were successfully developed by reducing Bi³⁺ on the surface of Bi₃O₄Cl. Consequently, the photocatalysts were used to remove ECs from water. The effects of developmental process and Bi metal plasmon resonance on the photoelectric performances of Bi-Bi₃O₄Cl were investigated through a series of characterizations. The UV-vis diffuse reflection and photoluminescence spectra revealed that the light absorption range of the photocatalyst gradually increased and the electron recombination rate gradually decreased with the introduction of Bi metals. The optimal removal rates of ciprofloxacin and tetrabromobisphenol A by Bi-Bi₃O₄Cl were 93.8% and 96.4%; the respective reaction rate constants were 5.48 and 4.93 times higher than that of Bi₃O₄Cl. The mechanism study indicated that main reactants in the photocatalytic system were •O₂^- radicals and photogenerated holes, and the existence of oxygen vacancies and Bi metals promoted electron transfer in photocatalyst. In conclusion, this research produces a novel, green, highly efficient, and stable visible light photocatalyst for the removal of ECs from water.

Wastewater treatment and emerging contaminants: Bibliometric analysis

In recent years, emerging contaminants have been found in the wastewater, surface water, and even drinking water, which should be treated to ensure the safety of our living environment. In this study, we provide a comprehensive summary of wastewater treatment and emerging contaminants research from 1998 to 2021 by using the bibliometric analysis. This study is conducted based on the Web of Science Core Collection Database. The bibliometix R-package, VOSviewer and CiteSpace software are used for bibliometric analysis and science mapping. A dataset of 10, 605 publications has been retrieved. The analysis results show that China has produced the most publications. China and the United States have the closest cooperation. Analysis of the most cited papers reveals that the purification or removal techniques such as ozonation or membrane filtration can effectively remove pharmaceutical compounds from the water environment. We also found that the efficient detection of emerging contaminants and the optimization of removal methods are current challenges. Finally, future research directions are discussed.

Effects of reclaimed wastewater irrigation on soil-crop systems in China: A review

Reclaimed wastewater (RW) use represents a substantial opportunity to alleviate the growing scarcity of water for irrigation of agricultural crops in China. However, insufficient understanding of the effects and fates of possible contaminants in RW promotes concerns over crop safety and prevents the extensive incorporation of RW in agriculture. We reviewed the characteristics of contaminants in RW, the fate of contaminants in soil-crop systems, and the effects of RW irrigation on soil quality and crop growth in China. We found that concentrations of heavy metals in RW were higher than the permissible limits in some areas. The total concentrations and main categories of emerging contaminants and pathogens in RW varied markedly among municipal wastewater treatment plants, and the greatest risks of contamination were posed by ofloxacin, sulfamethoxazole, and erythromycin, the most frequently observed compounds with risk quotients >1. The negative effects of salts and nutrients in RW on soil quality and crop growth were minor and manageable. The accumulation of heavy metals and emerging contaminants in soils irrigated with RW did not pose an immediate risk to soils and crops. Changes in soil microbial populations, diversity, and activity caused by RW irrigation increased crop yields and protected crops against contaminants. However, attention is necessary to the risks of bioaccumulation in soils and crops of heavy metals, emerging contaminants, intermediate metabolites, and pathogens, and their effects on human health with long-term RW irrigation. We recommend irrigation practices, crop screening, soil treatments, prioritizing the risks of contaminants, and comprehensive management to increase safety in RW used for agricultural irrigation.

Contaminants of emerging concern (CECs) in aquaculture effluent: Insight into breeding and rearing activities, alarming impacts, regulations, performance of wastewater treatment unit and future approaches

The contamination of aquaculture products and effluents by contaminants of emerging concern (CECs) from the direct chemical use in aquaculture activities or surrounding industries is currently an issue of increasing concern as these CECs exert acute and chronic effects on living organisms. CECs have been detected in aquaculture water, sediment, and culture species, and antibiotics, antifoulants, and disinfectants are the commonly detected groups. Through accumulation, CECs can reside in the tissue of aquaculture products and eventually consumed by humans. Currently, effluents containing CECs are discharged to the surrounding environment while producing sediments that eventually contaminate rivers as receiving bodies. The rearing (grow-out) stages of aquaculture activities are issues regarding CECs-contamination in aquaculture covering water, sediment, and aquaculture products. Proper regulations should be imposed on all aquaculturists to control chemical usage and ensure compliance to guidelines for appropriate effluent treatment. Several techniques for treating aquaculture effluents contaminated by CECs have been explored, including adsorption, wetland construction, photocatalysis, filtration, sludge activation, and sedimentation. The challenges imposed by CECs on aquaculture activities are discussed for the purpose of obtaining insights into current issues and providing future approaches for resolving associated problems. Stakeholders, such as researchers focusing on environment and aquaculture, are expected to benefit from the presented results in this article. In addition, the results may be useful in establishing aquaculture-related CECs regulations, assessing toxicity to living biota, and preventing pollution.

Wastewater fertigation in agriculture: Issues and opportunities for improved water management and circular economy

Water shortages are an issue of growing worldwide concern. Irrigated agriculture accounts for about 70% of total freshwater withdrawals globally, therefore alternatives to use of conventional sources need to be investigated. This paper critically reviews the application of treated wastewater for agricultural fertigation (i.e., water and nutrient recovery) considering different perspectives: legislation, agronomic characteristics, social acceptability, sustainability of treatment technologies. Critical issues that still need further investigation for a wider application of fertigation practices include accumulation of emerging contaminants in soils, microbiological and public health implications, and stakeholders' acceptance. A techno-economic methodological approach for assessing the sustainability of treated wastewater reuse in agriculture is subsequently proposed herein, which considers different possible local conditions (cultivated crops and effluent characteristics). The results showed that tailoring effluent characteristics to the desired nutrient composition could enhance the process economic sustainability; however, water savings have a major economic impact than fertilizers' savings, partly due to limited P reuse efficiency. The developed methodology is based on a practical approach and may be generalized to most agricultural conditions, to evaluate and encourage safe and efficient agricultural wastewater reuse practices.

Aquatic toxicity and aquatic ecological risk assessment of wastewater-derived halogenated phenolic disinfection byproducts

Increasing number of wastewater-derived aliphatic and phenolic disinfection byproducts (DBPs) were discharged into aquatic environment with the discharge of disinfected wastewater. However, the currently available aquatic toxicity data and the aquatic ecological risk information of them are limited, especially for wastewater-derived phenolic DBPs. In this study, we investigated the acute toxicity of 7 phenolic DBPs that selected from the typical five groups of phenolic DBPs (2,4,6-trihalo-phenols, 2,6-dihalo-4-nitrophenols, 3,5-dihalo-4-hydroxybenzaldehydes, 3,5-dihalo-4-hydroxybenzoic acids and halo-salicylic acids) and 4 aliphatic DBPs to Gobiocypris rarus and also assessed their potential aquatic ecological risk. Experimental results indicated that the half lethal concentration (LC₅₀) values of 2,4,6-trihalo-phenols and 2,6-dihalo-4-nitrophenols ranged from 1 to 10 mg/L; While that of 3,5-dihalo-4-hydroxybenzaldehydes was between 10 and 100 mg/L, and 3,5-dihalo-4-hydroxybenzoic acids and halo-salicylic acids was >100 mg/L. The toxicity mode of action (MOA) identification results from three methods suggested that no clear and consistent MOA were obtained for those 11 DBPs currently. The species-specific aquatic toxicity analysis results highlighted that no aquatic species would be considered as the most sensitive species for all 11 DBPs. However, crustacean and fish were more sensitive than that of algae for most of tested compounds. Lastly, the aquatic ecological risk assessment results of those 11 DBPs revealed that all 7 phenolic and 2 aliphatic DBPs (2-bromoacetamide and bromodichloromethane) had low aquatic ecological risk, while dichloroacetic acid and dibromoacetonitrile had high aquatic ecological risk. The low environmental concentration was the main reason why high toxic phenolic DBPs (2,4,6-trihalo-phenols and 2,6-dihalo-4-nitrophenols) exhibited low ecological risk. Their ecological risk may increase with the increases of corresponding environmental concentration. Thus, more efforts should be made to determine other potential harmful effects of those high toxic phenolic DBPs and to minimize their potential ecological risk by taking appropriate measures.

Adsorptive remediation of naproxen from water using in-house developed hybrid material functionalized with iron oxide

Every year, a considerable volume of medications is consumed. Because these medications are not entirely eliminated in the sewage treatment plants and impact the surface waterways, the environmental pollution problem arises. This study objective was to evaluate the possibility of using an absorbent material made with of polyethylene terephthalate and sugarcane bagasse ash functionalized with iron oxide (PETSCA/Fe³⁺) in the removal of naproxen from water. The feasibility of having viable features in becoming an efficient adsorbent was first determined. The batch test was performed, allowing the dose effect, adsorption kinetics, and isotherm models to be evaluated. The determination of naproxen (NAP) concentration in water was analyzed on a high-performance liquid chromatograph and Langmuir method best represented the adsorption isotherm model. PETSCA/Fe³⁺ adsorbent material demonstrated potential in the naproxen removal at a low cost. The batching process was satisfactory, with 0.30 g of composite being the optimum fit for the system. The adsorption kinetics was determined and described by the pseudo second order model, with an average correlation coefficient (R²) of 0.974. The adsorption system model was best represented by the Langmuir isotherm curve. Moreover, adsorption in the presence of H₂O₂ had a positive impact on the process, removing 81.9% of NAP, whereas the process without H₂O₂ did not remove more than 62.0% of NAP. Therefore, because of its good qualities for NAP removal, PETSCA/Fe³⁺ is recommended as adsorbent material, primarily in small-volume water filtration systems.

Pollution characterization of pharmaceutically active compounds (PhACs) in the northwest of Tai Lake Basin, China: Occurrence, temporal changes, riverine flux and risk assessment

PhACs have attracted great attentions of researchers because of their potential ecological and healthy risks. However, their long-term pollution tendency study is very scarce. In this study, 32 target PhACs from surface water, wastewater treatment plants, fishponds and livestock farms were investigated in Wujin, a city located in the northeast of Tai Lake, using grab sampling. The occurrence, spatiotemporal distribution characteristics, potential sources, riverine flux and risk assessment were systematically analyzed. It was found that non-antibiotics were the mainly PhACs category in Wujin and CF, SMX were the predominant non-antibiotics and antibiotics, respectively. Besides, the average concentrations of total PhACs were 586.6 ng L^-1 and 273.2 ng L^-1 in 2018 and 2019, respectively. This improvement could be mainly attributed to the closure of fishponds and livestock farms. Moreover, CF/CBZ ratios which was considered as an indicator to trace untreated wastewater decrease significantly in 2019, and this was also a main reason for the improvement. Riverine flux could be calculated through arranging control sampling sites in the boundary and the net riverine inflow flux of PhACs in Wujin was 264.3 kg/a. Finally, CF, SMX, EM were evaluated as the high risk contaminants based on a comprehensive risk assessment method.

Which Micropollutants in Water Environments Deserve More Attention Globally?

Increasing chemical pollution of aquatic environments is a growing concern with global relevance. A large number of organic chemicals are termed as "micropollutants" due to their low concentrations, and long-term exposure to micropollutants may pose considerable risks to aquatic organisms and human health. In recent decades, numerous treatment methods and technologies have been proposed to remove micropollutants in water, and typically several micropollutants were chosen as target pollutants to evaluate removal efficiencies. However, it is often unclear whether their toxicity and occurrence levels and frequencies enable them to contribute significantly to the overall chemical pollution in global aquatic environments. This review intends to answer an important lingering question: Which micropollutants or class of micropollutants deserve more attention globally and should be removed with higher priority? Different risk-based prioritization approaches were used to address this question. The risk quotient (RQ) method was found to be a feasible approach to prioritize micropollutants in a large scale due to its relatively simple assessment procedure and extensive use. A total of 83 prioritization case studies using the RQ method in the past decade were compiled, and 473 compounds that were selected by screening 3466 compounds of three broad classes (pharmaceuticals and personal care products (PPCPs), pesticides, and industrial chemicals) were found to have risks (RQ > 0.01). To determine the micropollutants of global importance, we propose an overall risk surrogate, that is, the weighted average risk quotient (WARQ). The WARQ integrates the risk intensity and frequency of micropollutants in global aquatic environments to achieve a more comprehensive priority determination. Through metadata analysis, we recommend a ranked list of 53 micropollutants, including 36 PPCPs (e.g., sulfamethoxazole and ibuprofen), seven pesticides (e.g., heptachlor and diazinon), and 10 industrial chemicals (e.g., perfluorooctanesulfonic acid and 4-nonylphenol) for risk management and remediation efforts. One caveat is that the ranked list of global importance does not consider transformation products of micropollutants (including disinfection byproducts) and new forms of pollutants (including antibiotic resistance genes and microplastics), and this list of global importance may not be directly applicable to a specific region or country. Also, it needs mentioning that there might be no best answer toward this question, and hopefully this review can act as a small step toward a better answer.

Occurrence, transformation, bioaccumulation, risk and analysis of pharmaceutical and personal care products from wastewater: a review

Almost all aspects of society from food security to disease control and prevention have benefited from pharmaceutical and personal care products, yet these products are a major source of contamination that ends up in wastewater and ecosystems. This issue has been sharply accentuated during the coronavirus disease pandemic 2019 (COVID-19) due to the higher use of disinfectants and other products. Here we review pharmaceutical and personal care products with focus on their occurrence in the environment, detection, risk, and removal.

SUPPLEMENTARY INFORMATION

The online version contains supplementary material available at 10.1007/s10311-022-01498-7.

Utilizing ion mobility spectrometry-mass spectrometry for the characterization and detection of persistent organic pollutants and their metabolites

Persistent organic pollutants (POPs) are xenobiotic chemicals of global concern due to their long-range transport capabilities, persistence, ability to bioaccumulate, and potential to have negative effects on human health and the environment. Identifying POPs in both the environment and human body is therefore essential for assessing potential health risks, but their diverse range of chemical classes challenge analytical techniques. Currently, platforms coupling chromatography approaches with mass spectrometry (MS) are the most common analytical methods employed to evaluate both parent POPs and their respective metabolites and/or degradants in samples ranging from d rinking water to biofluids. Unfortunately, different types of analyses are commonly needed to assess both the parent and metabolite/degradant POPs from the various chemical classes. The multiple time-consuming analyses necessary thus present a number of technical and logistical challenges when rapid evaluations are needed and sample volumes are limited. To address these challenges, we characterized 64 compounds including parent per- and polyfluoroalkyl substances (PFAS), pesticides, polychlorinated biphenyls (PCBs), industrial chemicals, and pharmaceuticals and personal care products (PPCPs), in addition to their metabolites and/or degradants, using ion mobility spectrometry coupled with MS (IMS-MS) as a potential rapid screening technique. Different ionization sources including electrospray ionization (ESI) and atmospheric pressure photoionization (APPI) were employed to determine optimal ionization for each chemical. Collectively, this study advances the field of exposure assessment by structurally characterizing the 64 important environmental pollutants, assessing their best ionization sources, and evaluating their rapid screening potential with IMS-MS.

Chronic toxicity and environmental risk assessment of antivirals in Ceriodaphnia dubia and Raphidocelis subcapitata

Antiviral drugs are a class of medications used for treating viral infections. Due to their widespread use, especially in cases of pandemics and limited human metabolism, antivirals have been detected in multiple environmental matrices. This study aims to evaluate the chronic effects of acyclovir, efavirenz, lamivudine and zidovudine using Ceriodaphnia dubia and Raphidocelis subcapitata. The results with R. subcapitata showed the following toxicities: zidovudine (IC₅₀ = 5.442 mg L^-1) < acyclovir (IC₅₀ = 3.612 mg L^-1) < lamivudine (IC₅₀ = 3.013 mg L^-1) < efavirenz (IC₅₀ = 0.034 mg L^-1). The results of the chronic bioassay with C. dubia demonstrated that zidovudine is the least toxic (EC₅₀ = 5.671 mg L^-1), followed by acyclovir (EC₅₀ = 3.062 mg L^-1), lamivudine (EC₅₀ = 1.345 mg L^-1) and efavirenz (EC₅₀ = 0.026 mg L^-1). Both species have been shown to be sensitive to efavirenz. A risk quotient (RQ) was calculated, and efavirenz had an RQ greater than 1 for both species, and lamivudine had an RQ greater than 1 for C. dubia, representing a high ecological risk for these organisms. Antivirals pose a significant environmental risk to aquatic organisms and should be taken into consideration in future monitoring of water sources.

Occurrence, distribution and ecological risk assessment of polycyclic aromatic hydrocarbons and their derivatives in the effluents of wastewater treatment plants

In this study, we investigated the concentration distribution of parent polycyclic aromatic hydrocarbons (PAHs) and their derivatives in the effluents of 5 municipal wastewater treatment plants (WWTPs) in Beijing, China for eight months. We first identified the coexistence of PAHs, chlorinated PAHs (Cl-PAHs), brominated PAHs (Br-PAHs) and oxygenated PAHs (OPAHs) in the effluents of WWTPs. Three Cl-PAHs and 7 Br-PAHs were first found. The total concentrations of PAHs, Cl-PAHs, Br-PAHs and OPAHs ranged from 8.99-88.38, n.d.-5.70, n.d.-13.11 ng L^-1 and 15.47-106.92 ng L^-1, respectively. In terms of temporal distributions, the total concentrations of PAHs and OPAHs presented a decreasing trend from April to November and the total concentrations of Cl-PAHs and Br-PAHs fluctuated at lower levels. These results indicated that these compounds will be long-term discharged into the receiving river. In addition, Cl-PAHs, Br-PAHs and OPAHs were likely generated by transformations occurring during chlorination disinfection. For ecological risk assessment, risk quotients of 6 compounds, indeno[1,2,3-cd] pyrene, benzo[g,h,i]perylene, dibenz[a,h]anthracene, 6-bromobenzo[a]pyrene, 1,8-dibromopyrene and 1,6-dibromopyrene, were thought to indicate high ecological risk (fish). Furthermore, Cl-PAHs, Br-PAHs and OPAHs in the effluents of WWTPs can cause more serious environmental hazards than the corresponding PAHs.

An appraisal of data collection, analysis, and reporting adopted for water quality assessment: A case of Nigeria water quality research

The appropriate acquisition and processing of water quality data are crucial for water resource management. As such, published articles on water quality monitoring and assessment are meant to convey essential and reliable information to water quality experts, decision-makers, researchers, students, and the public. The implication is that such information must emanate from data obtained and analysed in an up-to-date, scientifically sound manner. Thus, inappropriate data analysis and reporting techniques could yield misleading results and mar the endeavours of achieving error-free conclusions. This study utilises the findings on water quality assessment in Nigeria over the last 20 years to reveal the likely trends in water quality research regarding data collection, data analysis, and reporting for physicochemical, bacteriological parameters, and trace organics. A total of 123 Web of Science and quartile ranked (Q1-Q4) published articles involving water quality assessment in Nigeria were analysed. Results indicated shortcomings in various aspects of data analysis and reporting. Consequently, we use simulated heatmaps and graphs to illustrate preferred ways of analysing, reporting, and visualising some regularly used descriptive and inferential statistics of water quality variables. Finally, we highlight alternative approaches to the customarily applied water quality assessment methods in Nigeria and emphasise other areas of deficiency that need attention for improved water quality research.

Modified Single-Walled Carbon Nanotube Membranes for the Elimination of Antibiotics from Water

The hydrophilic and hydrophobic single-walled carbon nanotube membranes were prepared and progressively applied in sorption, filtration, and pertraction experiments with the aim of eliminating three antibiotics—tetracycline, sulfamethoxazole, and trimethoprim—as a single pollutant or as a mixture. The addition of SiO₂ to the single-walled carbon nanotubes allowed a transparent study of the influence of porosity on the separation processes. The mild oxidation, increasing hydrophilicity, and reactivity of the single-walled carbon nanotube membranes with the pollutants were suitable for the filtration and sorption process, while non-oxidized materials with a hydrophobic layer were more appropriate for pertraction. The total pore volume increased with an increasing amount of SiO₂ (from 743 to 1218 mm³/g) in the hydrophilic membranes. The hydrophobic layer completely covered the carbon nanotubes and SiO₂ nanoparticles and provided significantly different membrane surface interactions with the antibiotics. Single-walled carbon nanotubes adsorbed the initial amount of antibiotics in less than 5 h. A time of 2.3 s was sufficient for the filtration of 98.8% of sulfamethoxazole, 95.5% of trimethoprim, and 87.0% of tetracycline. The thicker membranes demonstrate a higher adsorption capacity. However, the pertraction was slower than filtration, leading to total elimination of antibiotics (e.g., 3 days for tetracycline). The diffusion coefficient of the antibiotics varies between 0.7–2.7 × 10⁻¹⁰, depending on the addition of SiO₂ in perfect agreement with the findings of the textural analysis and scanning electron microscopy observations. Similar to filtration, tetracycline is retained by the membranes more than sulfamethoxazole and trimethoprim.

Study on the influence of operational and management processes of a water reclamation plant since COVID-19 situation

Reusing treated wastewater can effectively alleviate water shortages and water contamination problems but depends on ensuring the safety of the reclaimed water that is produced. The operating and management conditions for water reclamation plants in China have been changed since the outbreak of the COVID-19 epidemic in China at the end of 2019 to prevent emerging viruses being spread through wastewater treatment processes and the reclaimed water that is produced. Removal of pathogens and trace organic compounds (e.g., pharmaceuticals and personal care products and endocrine disrupting chemicals) in a real water reclamation plant after the start of COVID-19 epidemic was studied. Disinfection byproduct formation caused by chlorine being added to meet disinfection requirements was also assessed. The pathogenic microorganism concentrations in effluent were <2 (most probable number)/L, and the removal rates for most trace organic compounds were >80% when advanced treatments were performed using ozone, ultraviolet light, and chlorine doses of 2 mg/L, 20.5 mJ/cm², and 2-3 mg/L, respectively. The main disinfection byproduct produced at a chlorine dose of 2 mg/L and a residence time of 1 h was chloroform (at concentrations <15 μg/L). The results indicated that the water reclamation processes with modified conditions gave high pathogen and trace organic compound removal rates and reasonably well-controlled disinfection byproduct concentrations.

Recent progress in green and biopolymer based photocatalysts for the abatement of aquatic pollutants

Enormous research studies on the abatement of anthropogenic aquatic pollutants including organic dyes, pesticides, cosmetics, antibiotics and inorganic species by using varieties of semiconductor photocatalysts have been reported in recent decades. Besides, many of these photocatalysts suffer in real applications owing to their high production cost and low stability. In many cases, the photocatalysts themselves are being considered as secondary pollutants. To eliminate these drawbacks, the green synthesized photocatalysts and the use of biopolymers as photocatalyst supports are considered in recent years. In this context, recent developments in green synthesized metals, metal oxides, other metal compounds, and carbon based photocatalysts in water purification are critically reviewed. Furthermore, the pivotal role of biopolymers including chitin, chitosan, cellulose, natural gum, hydroxyapatite, alginate in photocatalytic removal of aquatic pollutants is comprehensively reviewed. The presence of functional groups, electron trapping ability, biocompatibility, natural occurrence, and low production cost are the major reasons for using biopolymers in photocatalysis. Finally, the summary and conclusion are presented along with existing challenges in this research area.

Mitigation of emerging pollutants and pathogens in decentralized wastewater treatment processes: A review

Emerging pollutants (such as micropollutants, microplastics) and pathogens present in wastewater are of rising concern because their release can affect the natural environment and drinking water resources. In this decade, with increasing numbers of small-scale decentralized wastewater systems globally, the status of emerging pollutant and pathogen mitigation in the decentralized wastewater treatment processes has received more attention. This state-of-the-art review aims to discuss the mitigation efficiencies and mechanisms of micropollutants, microplastics, and pathogens in single-stage and hybrid decentralized wastewater treatment processes. The reviewed results revealed that hybrid wastewater treatment facilities could display better performance compared to stand-alone facilities. This is because the multiple treatment steps could offer various microenvironments, allowing incorporating several mitigation mechanisms (such as sorption, degradation, filtration, etc.) to remove complicated emerging pollutants and pathogens. The factors (such as system operation conditions, environmental conditions, wastewater matrix) influencing the removals of emerging pollutants from wastewater in these systems have been further identified. Nevertheless, it was found that very limited research work focused on synergised or conflicted effects of operation conditions on various emerging pollutants naturally present in the wastewater. Meanwhile, effective, reliable, and rapid analysis of the emerging pollutants and pathogens in the complicated wastewater matrix is still a major challenge.

Novel recyclable acidic hydrophobic deep eutectic solvents for highly efficient extraction of calcium dobesilate in water and urine samples

Deep eutectic solvents (DESs) have been considered to be one of the most promising green alternatives of conventional volatile solvents for liquid-liquid separation. However, acidic hydrophobic DESs have been less studied although they are of great importance for the extraction of compounds which are unstable in alkaline conditions. In this study, a novel family of acidic hydrophobic deep eutectic solvents was designed and prepared from methyl trioctyl ammonium chloride and a series of haloacetic acids. For the first time, the obtained DESs were used for extraction and determination of calcium dobesilate, which is an extensively used medicine for treating vascular diseases, but it can be easily oxidized under alkaline and neutral conditions. The factors influencing extraction process including pH, temperature, extract time, inorganic salts and organic coexistence were systematically investigated. It is found that these DESs exhibited outstanding extraction performance towards calcium dobesilate. The extraction equilibrium time was only 3 min in a wide range of pH (1.2-9.2) at room temperature and the extraction capacity was up to 504 mg/g. The detection limit of calcium dobesilate extracting from water samples was 0.05 μg/L and the limit of quantification was 0.5 μg/L. A variety of inorganic salts with the concentration up to 1.0 mol/L and common coexisting organic compounds, such as glucose and starch, with the concentration more than 1000 times higher than the target analyte had no obvious impact on the extraction efficiency. The relative recovery for real samples ranged from 93.2% to 108.6%. Furthermore, the DESs could be recycled and regenerated through back extraction. After fifteen cycles, the extraction efficiency was still up to 99%. Finally, the extraction and back extraction mechanism was discussed in detail.

Synthesis of N-Doped Magnetic WO3-x@Mesoporous Carbon Using a Diatom Template and Plasma Modification: Visible-Light-Driven Photocatalytic Activities

Synthesis of three-dimensional photocatalysts offers great potential for chemical conversion and hydrogen generation as appropriate solutions for environmental protection and energy shortage challenges. In this study, the magnetic WO_3-x@mesoporous carbon (M-WO_3-x@MC) was synthesized through the evaporation-induced self-assembly method applying diatom frustules as a natural template. Then, plasma modification was used to prepare the N-doped M-WO_3-x@MC (NM-WO_3-x@MC) with enhanced photocatalytic activity and durable performance. The WO_3-x was embedded in the conductive MC, which was also partially reduced by the carbon precursor within the heat-treatment procedure. The obtained M-WO_3-x@MC was treated by the plasma under an N₂ atmosphere for the production of the final photocatalyst containing both the N-doped WO_3-x and MC. As a result, the NM-WO_3-x@MC had larger surface area (208.4 m² g^-1), narrower band gap (2.3 eV), more visible light harvesting, and confined electron-hole pairs recombination. The H₂ generation rates of net WO₃ nanorods and NM-WO_3-x@MC nanocomposite were estimated as 532 and 2765 μmol g^-1 h^-1, respectively. Additionally, more than 90% of antibiotics (cephalexin, cefazolin and cephradine) degradation and 76% of total organic carbon elimination were obtained after 120 and 240 min of photocatalytic process under visible light irradiation. Eventually, more than eight intermediates were detected for each antibiotic degradation using the gas chromatography-mass spectrometer method, and based on the obtained results, the possible degradation pathways were suggested.

Emission of (chlorinated) reclaimed water into a Mediterranean River and its related effects to the dissolved organic matter fingerprint

High resolution mass spectrometry (HRMS) was used to investigate the dissolved organic matter (DOM) profile of a reclamation water trial performed in the Llobregat River (Spain) during summer 2019. 23 water samples (including tertiary effluents, surface river and drinking water), taken during five sampling campaigns, were analyzed and their van Krevelen diagrams were compared. The reclaimed water fingerprint was substantially different from the natural profile of the river, showing a higher number of heteroatomic signals (i.e. CHON, CHOS and CHONS) and the presence of high-intensity S-containing features. As a result, reclaimed water discharge introduced substantial changes in the signature of the lignin-like and soot-like compositional-spaces of the river DOM fingerprint. However, the effect on the drinking water fingerprint was, ultimately, very limited. Only a limited number of features (up to 34) were detected as exclusively emitted with the reclaimed water. During the second phase of the trial, the tertiary effluent was chlorinated for disinfection purposes. This process triggered the unexpected formation of a myriad of new features along the Llobregat River. Notably, 109 brominated/chlorinated features were detected, probably generated as a consequence of the photochemical decay of the emitted chloramines and their free-radical reaction with DOM, and three of them persisted in the final drinking water. The formation of halogenated species in situ in the Llobregat River entails uncertainty at ecological and water treatment levels and should be studied carefully to fully disclose the risks associated to wastewater effluent disinfection.

Water Security in a Changing Environment: Concept, Challenges and Solutions

Water is of vital and critical importance to ecosystems and human societies. The effects of human activities on land and water are now large and extensive. These reflect physical changes to the environment. Global change such as urbanization, population growth, socioeconomic change, evolving energy needs, and climate change have put unprecedented pressure on water resources systems. It is argued that achieving water security throughout the world is the key to sustainable development. Studies on holistic view with persistently changing dimensions is in its infancy. This study focuses on narrative review work for giving a comprehensive insight on the concept of water security, its evolution with recent environmental changes (e.g., urbanization, socioeconomic, etc.) and various implications. Finally, it presents different sustainable solutions to achieve water security. Broadly, water security evolves from ensuring reliable access of enough safe water for every person (at an affordable price where market mechanisms are involved) to lead a healthy and productive life, including that of future generations. The constraints on water availability and water quality threaten secured access to water resources for different uses. Despite recent progress in developing new strategies, practices and technologies for water resource management, their dissemination and implementation has been limited. A comprehensive sustainable approach to address water security challenges requires connecting social, economic, and environmental systems at multiple scales. This paper captures the persistently changing dimensions and new paradigms of water security providing a holistic view including a wide range of sustainable solutions to address the water challenges.

Occurrence and Fate of Emerging Pollutants in Water Environment and Options for Their Removal

Emerging pollutants (EPs) are chemicals known to cause major impacts on the terrestrial, aquatic life and human health as a result of their chronic and acute toxicity. Although lots of studies on EPs behavior in the aquatic environment are currently available in literature, an urgent requirement exists to complete toxicological studies and develop and implement efficient and ecological methods for their removal. This paper raises some relevant problems related to water environment pollution with EPs, the risks they can generate for aquatic life and humans and opportunities to reduce the effects of pollution by EPs removal. Categories of emerging chemicals of concern in the environment, their sources, fate and impacts, with some examples are discussed. Organic UV filters are shortly presented as a relative new EPs category, with a focus on the need to develop extensive experimental studies on their environmental occurrence, fate and removal. Furthermore, sources for the aquatic environment resulting from discharging EPs directly into rivers from wastewater treatment plants are examined. The incidence of environmental and human health risks related to EPs is also considered. The removal of EPs from the environment as a solution to risk mitigation is addressed, with emphasis on several non-conventional processes involving biological removal of EPs. The paper provides a critical look at the current challenges posed by the presence of emerging pollutants in the aquatic environment, with critical comments and recommendations for further research to reduce the impact of EPs on water and human health and improve the performance of developed methods for their removal.

Membrane Removal of Emerging Contaminants from Water: Which Kind of Membranes Should We Use?

Membrane technologies are nowadays widely used; especially various types of filtration or reverse osmosis in households, desalination plants, pharmaceutical applications etc. Facing water pollution, they are also applied to eliminate emerging contaminants from water. Incomplete knowledge directs the composition of membranes towards more and more dense materials known for their higher selectivity compared to porous constituents. This paper evaluates advantages and disadvantages of well-known membrane materials that separate on the basis of particle size, usually exposed to a large amount of water, versus dense hydrophobic membranes with target transport of emerging contaminants through a selective barrier. In addition, the authors present several membrane processes employing the second type of membrane.