Occurrence and fate of quinolone and fluoroquinolone antibiotics in a municipal sewage treatment plant

Source apportionment and specific-source-site risk of quinolone antibiotics for effluent-receiving urban rivers and groundwater in a city, China

There is a large surface-groundwater exchange downstream of wastewater treatment plants (WWTPs), and antibiotics upstream may influence sites downstream of rivers. Thus, samples from 9 effluent-receiving urban rivers (ERURs) and 12 groundwater sites were collected in Shijiazhuang City in December 2020 and April 2021. For ERURs, 8 out of 13 target quinolone antibiotics (QNs) were detected, and the total concentration of QNs in December and April were 100.6-4,398 ng/L and 8.02-2,476 ng/L, respectively. For groundwater, all target QNs were detected, and the total QNs concentration was 1.09-23.03 ng/L for December and 4.54-170.3 ng/L for April. The distribution of QNs was dissimilar between ERURs and groundwater. Most QN concentrations were weakly correlated with land use types in the system. The results of a positive matrix factorization model (PMF) indicated four potential sources of QNs in both ERURs and groundwater, and WWTP effluents were the main source of QNs. From December to April, the contribution of WWTP effluents and agricultural emissions increased, while livestock activities decreased. Singular value decomposition (SVD) results showed that the spatial variation of most QNs was mainly contributed by sites downstream (7.09%-88.86%) of ERURs. Then, a new method that combined the results of SVD and PMF was developed for a specific-source-site risk quotient (SRQ), and the SRQ for QNs was at high level, especially for the sites downstream of WWTPs. Regarding temporal variation, the SRQ for WWTP effluents, aquaculture, and agricultural emissions increased. Therefore, in order to control the antibiotic pollution, more attention should be paid to WWTP effluents, aquaculture, and agricultural emission sources for the benefit of sites downstream of WWTPs.

Determination of antibiotics during treatment of hospital wastewater using automated solid-phase extraction followed by UHPLC-MS: occurrence, removal and environmental risks

The extent of removal of pharmaceuticals by African-based wastewater treatment plants (WWTPs) is relatively unknown with various studies observing high concentrations in effluents. This is mainly due to WWTPs still utilising the traditional treatment methods which are known to be less effective. In this study, 15 selected antibiotics (amoxicillin, ampicillin, azithromycin, ciprofloxacin, doxycycline, erythromycin, gentamicin, metronidazole, norfloxacin, ofloxacin, penicillin, sulfamethoxazole, sulfapyridine, tetracycline and trimethoprim) were monitored in wastewater as it goes through sedimentation (primary and secondary), aeration and chlorination stages of a WWTP. Analytical method involved solid-phase extraction followed by liquid chromatographic determination. Removal efficiencies during sedimentation were generally positive with doxycycline achieving 80-95.8%, while negative removal efficiencies were observed for penicillin V (-46.4 to -17.1%) and trimethoprim (-26.2 to -18.9%). The aeration and agitation stage resulted in concentration enhancement for several antibiotics with seven of them ranging between -273 and -15.5%. This stage was responsible for the relatively low overall removal efficiencies in which only 4 antibiotics (doxycycline, tetracycline, ciprofloxacin, and erythromycin) experienced overall removal efficiencies above 50%. The recorded effluent concentrations ranging between 0.0130 and 0.383 ng/mL were translated to low potential for development of antibiotic resistance genes in the receiving environments while ecotoxicity risk was high for only amoxicillin, ampicillin and sulfapyridine. The study has provided an overview of the performance of common wastewater treatment processes in South Africa and hopes that more monitoring and environmental risk data can be made available towards drafting of antibiotic priority lists that cater for Africa.

Mechanism insights into hydrothermal-activated tannic acid (TA) for simultaneously sewage sludge deep dewatering and antibiotics removal

Tannic acid (TA) aided hydrothermal treatment (HT) can decrease effective HT temperatures for sludge deep dewatering by chelator protein, but faces notable and economic challenges including the failure to remove antibiotics and the limited protein binding capacity. Herein, hydrothermally activated TA (in situ TA + HT) was conducted to simultaneously improve sludge dewaterability and antibiotic (tetracycline (TC), oxytetracycline (OTC), norfloxacin (NOR), ofloxacin (OFL)) removal. Compared to traditional HT and HT + TA treatment, the in-situ TA + HT process could further strengthen the TA-aided HT efficacy in enhancing sludge and reducing the protein content in the filtrate simultaneously; in which the optimal HT temperature for the dewatering of the sludge was reduced from 180 °C to 140 °C. Furthermore, the total removal efficiency of target antibiotics was achieved at more than 71.0-94.7% for TC and OTC, and 72.0-84.8% for NOR and OFL. The highly reactive species (·OH) generation and the electron transfer efficiency from the hydrothermal-activated TA process were responsible for the elimination of antibiotics and promoted the hydrolyzation and mineralization of HMW protein in sludge during the HT process. Meanwhile, the degradation of HMW proteins and the destruction of the secondary structure of these proteins resulted in improved hydrophobicity and dewaterability of sludge. Hydrothermally activated TA induces covalent binding with the protein. As a result, hydrothermal-activated TA could promote the removal of antibiotics and proteinaceous compounds from the sludge samples, improving the hydrophobicity of sludge and releasing bound water from the sludge flocs during HT. Finally, the cost of hydrothermal-activated TA was 66.51% lower than that of thermal drying treatment. This study not only proposed an effective method to improve traditional HT for sludge thermal dry-free treatment, but also provided new information on the catalysis roles of polyphenols in the hydrothermal conversion of sludge.

Effects of surfactants on the adsorption of norfloxacin onto ferrihydrite: comparison between anionic and cationic surfactants

There is little information on how widespread surfactants affect the adsorption of norfloxacin (NOR) onto iron oxide minerals. In order to elucidate the effects of various surfactants on the adsorption characteristics of NOR onto typical iron oxides, we have explored the different influences of sodium dodecylbenzene sulfonate (SDBS), an anionic surfactant, and didodecyldimethylammonium bromide (DDAB), a cationic surfactant, on the interactions between NOR and ferrihydrite under different solution chemistry conditions. Interestingly, SDBS facilitated NOR adsorption, whereas DDAB inhibited NOR adsorption. The adsorption-enhancement effect of SDBS was ascribed to the enhanced electrostatic attraction, the interactions between the adsorbed SDBS on ferrihydrite surfaces and NOR molecules, and the bridging effect of SDBS between NOR and iron oxide. In comparison, the adsorption-inhibition effect of DDAB owning to the adsorption site competitive adsorption between NOR and DDAB for the effective sites as well as the steric hindrance between NOR-DDAB complexes and the adsorbed DDAB on ferrihydrite surfaces. Additionally, the magnitude of the effects of surfactants on NOR adsorption declined with increasing pH values from 5.0 to 9.0, which was related to the amounts of surfactant binding to ferrihydrite surfaces. Moreover, when the background electrolyte was Ca2+, the enhanced effect of SDBS on NOR adsorption was caused by the formation of NOR-Ca2+-SDBS complexes. The inhibitory effect of DDAB was due to the DDAB coating on ferrihydrite, which undermined the cation-bridging effect. Together, the findings from this work emphasize the essential roles of widely existing surfactants in controlling the environmental fate of quinolone antibiotics.

Occurrence, fate, and ecological risk of antibiotics in wastewater treatment plants in China: A review

This review offers a comprehensive overview of the occurrence, fate, and ecological risk associated with six major categories of antibiotics found in influent, effluent, and sludge from urban wastewater treatment plants (WWTPs) in China. Further exploration includes examining the correlation between antibiotic residual rates in the effluents and process parameters of urban WWTPs across the country. Lastly, a nationwide and urban cluster-specific evaluation of the ecological risk posed by antibiotics in WWTPs is conducted. The findings reveal that the average concentrations of antibiotics in influent, effluent, and sludge from urban WWTPs in China are 786.2 ng/L, 311.2 ng/L, and 186.8 μg/kg, respectively. Among the detected antibiotics, 42% exhibit moderate to high ecological risk in the effluent, with ciprofloxacin, sulfamethoxazole, erythromycin, azithromycin, and tetracycline posing moderate to high ecological risks in sludge. The current biological treatment processes in WWTPs demonstrate inefficacy in removing antibiotics. Hence, there is a pressing need to develop and integrate innovative technologies, such as advanced oxidation processes. This review aims to offer a more comprehensive understanding and identify priority antibiotics for control to effectively manage antibiotic pollution within WWTPs at both national and regional levels.

A group-targeting biosensor for sensitive and rapid detection of quinolones in water samples

BACKGROUND

Quinolones (QNs) widely exist in the environment due to their wide range of applications and poor metabolic properties, resulting in the generation and spread of resistance genes, posing a potential threat to human health. Traditional analytical methods cannot detect all broad ranges of QNs simultaneously. The development of facile, efficient and reliable method for quantification and assessment of the total QNs is a long-lasting challenge.

RESULTS

We hereby provide a simple, sensitive and instantaneous group-targeting biosensor for the detection of total QNs in environmental water samples. The biosensor is based on a group-specific antibodies with high affinity against QNs. Fluorescent labeled antibodies bound to the coated antigen modified on the surface of the transducer, and excited by the evanescent waves. The detected fluorescent signal is inversely proportional to the QNs concentration. This biosensor exhibited excellent performance with detection limits lower than 0.15 μg L-1 for all five QNs variants, and even lower than 0.075 μg L-1 for ciprofloxacin (CIP) and ofloxacin (OFL). Environmental water samples can be detected after simple pretreatment, and all detection steps can be completed in 10 min. The transducer has a high regenerative capacity and shows no significant signal degradation after two hundred detection cycles. The recoveries of QNs in a variety of wastewater range from 105 to 119%, confirming its application potential in the measurement of total QNs in reality.

SIGNIFICANCE

The biosensor can realize rapid and sensitive detection of total QNs in water samples by simple pretreatment, which overcomes the disadvantage of the traditional methods that require complex pretreatment and time-consuming, and pave the groundwork for expansive development centered around this technology.

All-solid-state Z-scheme ZnFe-LDH/rGO/g-C3N5 heterojunction for enhanced sonophotocatalytic degradation of ciprofloxacin: Performance and mechanistic insights

The fabrication of all-solid-state Z-scheme sonophotocatalysts is vital for improving the transfer rate of photogenerated electrons to remove antibiotics present in wastewater. Herein, a novel indirect Z-scheme ZnFe-layered double hydroxide (LDH)/reduced graphene oxide (rGO)/graphitic carbon nitride (g-C3N5) heterojunction was synthesized using a simple strategy. The ZnFe-LDH/rGO/g-C3N5 (ZF@rGCN) ternary composites were systematically characterized using different techniques. Results revealed that the 15%ZF@rGCN catalyst achieved a ciprofloxacin (CIP) degradation efficiency of 95% via the synergistic effect of sonocatalysis and photocatalysis. The improved sonophotocatalytic performance of the ZF@rGCN heterojunction was attributed to an increase in the number of active sites, a Z-scheme charge-transfer channel in ZF@rGCN, and an extended visible light response range. The introduction of rGO further enhanced the charge-transfer rate and preserved the reductive and oxidative sites of the ZF@rGCN system, thereby affording additional reactive species to participate in CIP removal. In addition, owing to its unique properties, rGO possibly increased the absorption of incident light and served as an electronic bridge in the as-formed ZF@rGCN catalyst. Finally, the possible CIP degradation pathways and the sonophotocatalytic Z-scheme charge-migration route of ZF@rGCN were proposed. This study presents a new approach for fabricating highly efficient Z-scheme sonophotocatalysts for environmental remediation.

Molecularly Imprinted Heterostructure-Assisted Laser Desorption Ionization Mass Spectrometry Analysis and Imaging of Quinolones

Quinolone residues resulting from body metabolism and waste discharge pose a significant threat to the ecological environment and to human health. Therefore, it is essential to monitor quinolone residues in the environment. Herein, an efficient and sensitive matrix-assisted laser desorption/ionization mass spectrometry (MALDI/MS) method was devised by using a novel molecularly imprinted heterojunction (MIP-TNs@GCNs) as the matrix. Molecularly imprinted titanium dioxide nanosheets (MIP-TNs) and graphene-like carbon nitrides (GCNs) were associated at the heterojunction interface, allowing for the specific, rapid, and high-throughput ionization of quinolones. The mechanism of MIP-TNs@GCNs was clarified using their adsorption properties and laser desorption/ionization capability. The prepared oxygen-vacancy-rich MIP-TNs@GCNs heterojunction exhibited higher light absorption and ionization efficiencies than TNs and GCNs. The good linearity (in the quinolone concentration range of 0.5-50 pg/μL, R2 > 0.99), low limit of detection (0.1 pg/μL), good reproducibility (n = 8, relative standard deviation [RSD] < 15%), and high salt and protein resistance for quinolones in groundwater samples were achieved using the established MIP-TNs@GCNs-MALDI/MS method. Moreover, the spatial distributions of endogenous compounds (e.g., amino acids, organic acids, and flavonoids) and xenobiotic quinolones from Rhizoma Phragmitis and Rhizoma Nelumbinis were visualized using the MIP-TNs@GCNs film as the MALDI/MS imaging matrix. Because of its superior advantages, the MIP-TNs@GCNs-MALDI/MS method is promising for the analysis and imaging of quinolones and small molecules.

Occurrence and fate of pharmaceutical pollutants in wastewater: Insights on ecotoxicity, health risk, and state-of-the-art removal

Pharmaceutical active compound (PhAC) residues are considered an emerging micropollutant that enters the aquatic environment and causes harmful ecotoxicity. The significant sources of PhACs in the environment include the pharmaceutical industry, hospital streams, and agricultural wastes (animal husbandry). Recent investigations demonstrated that wastewater treatment plants (WWTPs) are an important source of PhACs discharging ecosystems. Several commonly reported that PhACs are detected in a range level from ng L-1 to μg L-1 concentration in WWTP effluents. These compounds can have acute and chronic adverse impacts on natural wildlife, including flora and fauna. The approaches for PhAC removals in WWTPs include bioremediation, adsorption (e.g., biochar, chitosan, and graphene), and advanced oxidation processes (AOPs). Overall, adsorption and AOPs can effectively remove PhACs from wastewater aided by oxidizing radicals. Heterogeneous photocatalysis has also proved to be a sustainable solution. Bioremediation approaches such as membrane bioreactors (MBRs), constructed wetlands (CWs), and microalgal-based systems were applied to minimize pharmaceutical pollution. Noteworthy, applying MBRs has illustrated high removal efficiencies of up to 99%, promising prospective future. However, WWTPs should be combined with advanced solutions, e.g., AOPs/photodegradation, microalgae-bacteria consortia, etc., to treat and minimize their accumulation. More effective and novel technologies (e.g., new generation bioremediation) for PhAC degradation must be investigated and specially designed for a low-cost and full-scale. Investigating green and eco-friendly PhACs with advantages, e.g., low persistence, no bioaccumulation, less or non-toxicity, and environmentally friendly, is also necessary.

An evaluation of conventional and nature-based technologies for controlling antibiotic-resistant bacteria and antibiotic-resistant genes in wastewater treatment plants

Antibiotic resistance is a globally recognized health concern which leads to longer hospital stays, increased morbidity, increased mortality, and higher medical costs. Understanding how antibiotic resistance persists and exchanges in environmental systems like soil, water, and wastewater are critically important for understanding the emergence of pathogens with new resistance profiles and the subsequent exposure of people who indirectly/directly come in contact with these pathogens. There are concerns about the widespread application of prophylactic antibiotics in the clinical and agriculture sectors, as well as chemicals/detergents used in food and manufacturing industries, especially the quaternary ammonium compounds which have been found responsible for the generation of resistant genes in water and soil. The rates of horizontal gene transfer increase where there is a lack of proper water/wastewater infrastructure, high antibiotic manufacturing industries, or endpoint users - such as hospitals and intensive agriculture. Conventional wastewater treatment technologies are often inefficient in the reduction of ARB/ARGs and provide the perfect combination of conditions for the development of antibiotic resistance. The wastewater discharged from municipal facilities may therefore be enriched with bacterial communities/pathogens and provide a suitable environment (due to the presence of nutrients and other pollutants) to enhance the transfer of antibiotic resistance. However, facilities with tertiary treatment (either traditional/emerging technologies) provide higher rates of reduction. This review provides a synthesis of the current understanding of wastewater treatment and antibiotic resistance, examining the drivers that may accelerate their possible transmission to a different environment, and highlighting the need for tertiary technologies used in treatment plants for the reduction of resistant bacteria/genes.

Comprehensive evaluation of antibiotics pollution the Yangtze River basin, China: Emission, multimedia fate and risk assessment

Antibiotics have attracted global attention because of their potential ecological and health risks. The emission, multimedia fate and risk of 18 selected antibiotics in the entire Yangtze River basin were evaluated by using a level Ⅳ fugacity model. High antibiotic emissions were found in the middle and lower reaches of the Yangtze River basin. The total antibiotic emissions in the Yangtze River basin exceeded 1600 tons per year between 2013 and 2021. The spatial distribution of antibiotics concentration was the upper Yangtze River > middle Yangtze River > lower Yangtze River, which is positively correlated with animal husbandry size in the basin. Temperature and precipitation increases may decrease the antibiotic concentrations in the environment. Transfer fluxes showed that source emission inputs, advection processes, and degradation fluxes contributed more to the total input and output. High ecological risks in the water environment were found in 2018, 2019, 2020, and 2021. The comprehensive health risk assessment through drinking water and fish consumption routes showed that a small part of the Yangtze River basin is at medium risk, and children have a relatively high degree of health risk. This study provides a scientific basis for the pollution control of antibiotics at the basin scale.

Photocathodic Activation of Peroxymonosulfate in a Photofuel Cell: A Synergetic Signal Amplification Strategy for a Self-Powered Photoelectrochemical Sensor

A self-powered photoelectrochemical (PEC) sensor has attracted widespread attention in the field of analysis, but it is still a challenge to enhance its response signals with rational strategies. In this work, a novel self-powered PEC sensing platform was developed for the quantitative detection of gatifloxacin (GAT) based on a photofuel cell consisting of two types of ZIF-derived ZnO/Co3O4 heterojunctions as photoactive materials. Peroxymonosulfate (PMS) was first used as an electron acceptor coupled with a photofuel cell to develop a synergetic signal amplification strategy. In a dual-photoelectrode system, the PMS activation on the ZnO@Co3O4 photocathode not only accelerated electron transfer from the Co3O4@ZnO photoanode to achieve strong signal intensity but also improved the sensing sensitivity by the oxidation reaction of generated highly active radicals to GAT. Compared with the absence of electron acceptors, the introduction of PMS produced a 2-fold enhancement in the signal output performance and a more than 72-fold improvement in the signal sensitivity. For the construction of the sensing interface, a molecularly imprinted polymer was assembled on the photocathode to specifically recognize GAT. The proposed sensor exhibited a detection range of 10-1 to 105 pM with a detection limit of 0.065 pM. The proposed sensing method has the advantages of sensitivity, simplicity, reliable stability, and anti-interference ability, which opens the door to the design of high-performance self-powered PEC sensors.

Roles of extracellular polymeric substances in the adsorption and removal of norfloxacin during hydrothermal treatment of sewage sludge

Hydrothermal treatment (HT) is promising to remove antimicrobials from sewage sludge (SS); however, the mechanism of antimicrobial degradation during the HT of SS is not fully understood. In this study, the roles of extracellular polymeric substances (EPS) in the removal and transformation of norfloxacin (NOR) during the HT of SS at temperatures of 100 and 160 °C were investigated. The results indicated that the degradation of NOR increased with increasing HT temperature, with maximum NOR removal (52%) achieved at 160 °C. Furthermore, the NOR in sludge showed higher degradation efficiencies than the control as HT temperature was higher than 120 °C. Evident promotion effects of bound-EPS (B-EPS) in sludge were observed on the NOR degradation as HT temperature was higher than 120 °C, leading to the mineralization and deamination of protein-like components in EPS during HT. Beside, the adsorption capacity of NOR during the HT of SS decreased at temperatures higher than 120 °C. The evolution of the spatial structure of B-EPS was predominantly responsible for the adsorption of antimicrobials, a spontaneous process driven mainly by hydrophilic interactions. With the hydrothermal conversion of B-EPS, the electron transfer, and reactive species (3EPS* and ·OH) derived from B-EPS could facilitate the degradation of NOR. In particular, hydrogen bonds between B-EPS and NOR increased the apparent yield of ·OH and accelerated the decarboxylation of NOR during HT at temperatures higher than 120 °C. A toxicity evaluation suggested that HT for NOR degradation could attenuate toxicity, whereas deep oxidation or mineralization would be needed to promote ecosystem safety. These findings provide new insights into the hydrothermal activation of EPS and the interrelated hydrothermal fate of antimicrobials and other toxic pollutants in sludge.

Optimizing ciprofloxacin removal through regulations of trophic modes and FNA levels in a moving bed biofilm reactor performing sidestream partial nitritation

The performance of partial nitritation (PN)-moving bed biofilm reactor (MBBR) in removal of antibiotics in the sidestream wastewater has not been investigated so far. In this work, the removal of ciprofloxacin was assessed under varying free nitrous acid (FNA) levels and different trophic modes. For the first time, a positive correlation was observed between ciprofloxacin removal and FNA levels, either in the autotrophic PN-MBBR or in the mixotrophic PN-MBBR, mainly ascribed to the FNA-stimulating effect on heterotrophic bacteria (HB)-induced biodegradation. The maximum ciprofloxacin removal efficiency (∼98 %) and removal rate constant (0.021 L g-1 SS h-1) were obtained in the mixotrophic PN-MBBR at an average FNA level of 0.056 mg-N L-1, which were 5.8 and 51.2 times higher than the corresponding values in the autotrophic PN-MBBR at 0 mg FNA-N L-1. Increasing FNA from 0.006 to 0.056 mg-N L-1 would inhibit ammonia oxidizing bacteria (AOB)-induced cometabolism and metabolism from 10.2 % and 6.9 % to 6.2 % and 6.4 %, respectively, while HB-induced cometabolism and metabolism increased from 31.2 % and 22.7 % to 41.9 % and 34.5 %, respectively. HB-induced cometabolism became the predominant biodegradation pathway (75.9 %-85.8 %) in the mixotrophic mode. Less antimicrobial biotransformation products without the piperazine or fluorine were newly identified to propose potential degradation pathways, corresponding to microbial-induced metabolic types and FNA levels. This work shed light on enhancing antibiotic removal via regulating both FNA accumulation and organic carbon addition in the PN-MBBR process treating sidestream wastewater.

Occurrence and removal rate of typical pharmaceuticals and personal care products (PPCPs) in an urban wastewater treatment plant in Beijing, China

The occurrence and removal rate of 52 typical pharmaceuticals and personal care products (PPCPs) were investigated in a wastewater treatment plant in Beijing, China. Thirty-three PPCPs were found in the influent, with caffeine (CF, 11387.0 ng L-1) being the most abundant, followed by N,N-diethyl-meta-toluamide (DEET, 9568.4 ng L-1), metoprolol (MTP, 930.2 ng L-1), and diclofenac (DF, 710.3 ng L-1). After treatment processes, the cumulative concentration of PPCPs decreased from 2.54 × 104 ng L-1 to 1.44 × 103 ng L-1, with the overall removal efficiency (RE) of 94.3%. Different treatment processes showed varying contributions in removing PPCPs. PPCPs were efficiently removed in sedimentation, anoxic, and ultraviolet units. For individual compounds, a great variation in RE (52.1-100%) was observed. Twenty-two PPCPs were removed by more than 90%. The highly detected PPCPs in the influent were almost completely removed. Aerated grit chamber removed nearly 50% of fluoroquinolone (FQs) and more than 60% of sulfonamides. Most PPCPs showed low or negative removals during anaerobic treatment, except for CF which was eliminated by 64.9%. Anoxic treatment demonstrated positive removals for most PPCPs, with the exceptions of DF, MTP, bisoprolol, carbamazepine (CBZ), and sibutramine. DEET and bezafibrate were efficiently removed during the secondary sedimentation. Denitrification biological filter and membrane filtration also showed positive effect on most PPCPs removals. The remaining compounds were oxidized by 16-100% in ozonation. DF, sulpiride, ofloxacin (OFL), trimethoprim, and phenolphthalein were not amenable to ultraviolet. After the treatment, the residue OFL, CBZ, and CF in receiving water were identified to pose high risk to aquatic organisms. Considering the complex mixtures emitted into the environment, therapeutic groups psychotropics, stimulant, and FQs were classified as high risk. These findings provide valuable insights into adopting appropriate measures for more efficient PPCPs removals, and emphasize the importance of continued monitoring specific PPCPs and mixtures thereof to safeguard the ecosystem.

Hospital and urban wastewaters shape the matrix and active resistome of environmental biofilms

Understanding the dynamics of antibiotic resistance gene (ARG) transfer and dissemination in natural environments remains challenging. Biofilms play a crucial role in bacterial survival and antimicrobial resistance (AMR) dissemination in natural environments, particularly in aquatic systems. This study focused on hospital and urban wastewater (WW) biofilms to investigate the potential for ARG dissemination through mobile genetic elements (MGEs). The analysis included assessing the biofilm extracellular polymeric substances (EPS), microbiota composition as well as metatranscriptomic profiling of the resistome and mobilome. We produced both in vitro and in situ biofilms and performed phenotypic and genomic analyses. In the in vitro setup, untreated urban and hospital WW was used to establish biofilm reactors, with ciprofloxacin added as a selective agent at minimal selective concentration. In the in situ setup, biofilms were developed directly in hospital and urban WW pipes. We first showed that a) the composition of EPS differed depending on the growth environment (in situ and in vitro) and the sampling origin (hospital vs urban WW) and that b) ciprofloxacin impacted the composition of the EPS. The metatranscriptomic approach showed that a) expression of several ARGs and MGEs increased upon adding ciprofloxacin for biofilms from hospital WW only and b) that the abundance and type of plasmids that carried individual or multiple ARGs varied depending on the WW origins of the biofilms. When the same plasmids were present in both, urban and hospital WW biofilms, they carried different ARGs.  We showed that hospital and urban wastewaters shaped the structure and active resistome of environmental biofilms, and we confirmed that hospital WW is an important hot spot for the dissemination and selection of antimicrobial resistance. Our study provides a comprehensive assessment of WW biofilms as crucial hotspots for ARG transfer. Hospital WW biofilms exhibited distinct characteristics, including higher eDNA abundance and expression levels of ARGs and MGEs, highlighting their role in antimicrobial resistance dissemination. These findings emphasize the importance of understanding the structural, ecological, functional, and genetic organization of biofilms in anthropized environments and their contribution to antibiotic resistance dynamics.

An investigation on removal of ciprofloxacin and norfloxacin by phycoremediation with an emphasis on acute toxicity and biochemical composition

Ciprofloxacin (CIP) and norfloxacin (NOR) belong to the class of emerging contaminants that are frequently detected in the aquatic environment as a binary mixture, responsible for the development of antibiotic-resistant genes and antibiotic-resistant bacteria. This study aims to investigate five different algal species Chlorella vulgaris (Cv), Chlorella pyrenoidosa (Cp), Scenedesmus obliquus (So), Tetradesmus sp (T) and Monoraphidium sp (M) for their tolerance and removal of binary mixture. The effects on biochemical composition in the algal species concerning the binary mixture and its removal efficiency are first reported in this study. The acute toxicity (96 h EC50) values are in the order of So > Cp > T > M > Cv, Chlorella vulgaris is the most sensitive algal species with 17.73 ± 0.24 mg/L and Scenedesmus obliquus is the least sensitive algal species with 39.19 ± 0.79 mg/L. The removal efficiency of the binary mixture was found to be in the order of So > Cp > T > M > Cv, Scenedesmus obliquus removed CIP (52.4%) and NOR (87.5%) with biodegradation as the major contributing removal mechanism. Furthermore, less toxic biotransformed products were detected in Scenedesmus obliquus and the biochemical characterization revealed that the growth-stimulating effect is higher with lipid (35%), carbohydrate (18%), and protein (33%) providing an advantage in the production of valuable biomass.

Animal production predominantly contributes to antibiotic profiles in the Yangtze River

Human-induced antibiotic pollution in the world's large rivers poses significant risk to riverine ecosystems, water quality, and human health. This study identified geophysical and socioeconomic factors driving antibiotic pollution in the Yangtze River by quantifying 83 target antibiotics in water and sediment samples collected in its 6300-km-long reach, followed by source apportionment and statistical modeling. Total antibiotic concentrations ranged between 2.05-111 ng/L in water samples and 0.57-57.9 ng/g in sediment samples, contributed predominantly by veterinary antibiotics, sulfonamides and tetracyclines, respectively. Antibiotic compositions were clustered according to three landform regions (plateau, mountain-basin-foothill, and plains), resulting from varying animal production practices (cattle, sheep, pig, poultry, and aquaculture) in the sub-basins. Population density, animal production, total nitrogen concentration, and river water temperature are directly associated with antibiotic concentrations in the water samples. This study revealed that the species and production of food animals are key determinants of the geographic distribution pattern of antibiotics in the Yangtze River. Therefore, effective strategies to mitigate antibiotic pollution in the Yangtze River should include proper management of antibiotic use and waste treatment in animal production.

Occurrence, distribution, and risk assessment of quinolone antibiotics in municipal sewage sludges throughout China

A nationwide study of the occurrence, distribution, potential drivers, and ecological risks of 24 quinolone antibiotics (QNs) in 74 Chinese sludge samples from 48 wastewater treatment plants (WWTPs) was conducted. In domestic sludge, the ∑QNs concentrations were <LOD to 21,925.10 ug/kg (mean: 4808.67 ug/kg), and ofloxacin had the highest concentration (<LOD-11,138.52 ug/kg), and detection frequency (98.48%). Of four generations QNs, the levels showed the following order: 2nd-generation QNs > 3rd-generation QNs > 4th-generation QNs > 1st-generation QNs. Meanwhile, abundant veterinary and human/veterinary quinolones (<LOD-2606.96 and <LOD-12,643.47 ug/kg, respectively) were detected in municipal sludge. Interestingly, the relatively low levels of veterinary quinolones (<LOD-299.21 ug/kg) were also found in industrial sludge (the relevant WWTPs receiving ≤ 10% domestic wastewater, without other direct entry of antibiotics). The correlation analysis demonstrated QNs contamination was negatively influenced by the air temperature of sampling days. The positive correlation between moxifloxacin contents and regional economy possibly suggested local regions with relatively high economic levels face a more difficult situation of QNs antibacterial activity. Environmental risk assessment indicated ofloxacin, ciprofloxacin, and moxifloxacin posed high ecological risks to the domestic sludge. This work delineates a valuable nationwide QNs contamination profile to support their safe use and control in China.

Risk control of antibiotics, antibiotic resistance genes (ARGs) and antibiotic resistant bacteria (ARB) during sewage sludge treatment and disposal: A review

Sewage sludge is an important reservoir of antibiotics, antibiotic resistance genes (ARGs), and antibiotic resistant bacteria (ARB) in wastewater treatment plants (WWTPs), and the reclamation of sewage sludge potentially threats human health and environmental safety. Sludge treatment and disposal are expected to control these risks, and this review summarizes the fate and controlling efficiency of antibiotics, ARGs, and ARB in sludge involved in different processes, i.e., disintegration, anaerobic digestion, aerobic composting, drying, pyrolysis, constructed wetland, and land application. Additionally, the analysis and characterization methods of antibiotics, ARGs, and ARB in complicate sludge are reviewed, and the quantitative risk assessment approaches involved in land application are comprehensively discussed. This review benefits process optimization of sludge treatment and disposal, with regard to environmental risks control of antibiotics, ARGs, and ARB in sludge. Furthermore, current research limitations and gaps, e.g., the antibiotic resistance risk assessment in sludge-amended soil, are proposed to advance the future studies.

A molecularly imprinted electrochemical sensor with dual functional monomers for selective determination of gatifloxacin

A molecularly imprinted electrochemical sensor was designed for the selective determination of gatifloxacin (GTX) based on dual functional monomers. Multi-walled carbon nanotube (MWCNT) enhanced the current intensity and zeolitic imidazolate framework 8 (ZIF8) provided a large surface area to produce more imprinted cavities. In the electropolymerization of molecularly imprinted polymer (MIP), p-aminobenzoic acid (p-ABA) and nicotinamide (NA) were used as dual functional monomers, and GTX was the template molecule. Taking [Fe(CN)6]3-/4- as an electrochemical probe, an oxidation peak on the glassy carbon electrode was located at about 0.16 V (vs. saturated calomel electrode). Due to the diverse interactions among p-ABA, NA, and GTX, the MIP-dual sensor exhibited higher specificity towards GTX than MIP-p-ABA and MIP-NA sensors. The sensor had a wide linear range from 1.00 × 10-14 to 1.00 × 10-7 M with a low detection limit of 2.61 × 10-15 M. Satisfactory recovery between 96.5 and 105% with relative standard deviation from 2.4 to 3.7% in real water samples evidenced the potential of the method in antibiotic contaminant determination.

Exploration of an efficient method for removing antibiotics from water and digested sewage sludge using Fe(VI): Kinetics and P phytoavailability and compostability in treated sludge

Potassium ferrate (K₂FeO₄) containing hexavalent iron [Fe(VI)] is an environmentally friendly oxidant, which possesses strong oxidizing power to treat wastewater and sludge. Therefore, the present study investigated degradation of selected antibiotics, namely levofloxacin (LEV), ciprofloxacin (CIP), oxytetracycline (OTC), and azithromycin (AZI), in water and anaerobically digested sewage sludge samples using Fe(VI). The effects of different Fe(VI) concentrations and initial pH values on antibiotic removal efficiency were evaluated. Under the studied conditions, LEV and CIP were almost completely removed from water samples, following second-order kinetics. In addition, over 60% of the four selected antibiotics were removed from sludge samples using 1 g L^-1 Fe(VI). Furthermore, P phytoavailability and compostability of Fe(VI)-treated sludge were evaluated using different extraction reagents and a small composting unit. The extraction efficiency of phytoavailable P using 2% citric acid and neutral ammonium citrate was approximately 40% and 70%, respectively. The mixture of Fe(VI)-treated sludge and rice husk was self-heated in a closed composting reactor through the biodegradation of organic matter derived from the treated sludge. Therefore, Fe(VI)-treated sludge may be used as an organic material containing phytoavailable P for compost.

Adsorption of fluoroquinolone antibiotics onto ferrihydrite under different anionic surfactants and solution pH

To date, little information is available regarding the impacts of the widespread anionic surfactants on the adsorption behaviors of antibiotics onto typical iron oxides. Herein, we have investigated the effects of two typical surfactants (sodium dodecyl sulfate (SDS) and sodium dodecylbenzene sulfonate (SDBS)) on the adsorption of two widely used antibiotics (i.e., levofloxacin (LEV) and ciprofloxacin (CIP)) onto ferrihydrite. Results of kinetic experiments showed that the adsorption of antibiotics was well fitted by the pseudo-second-order kinetic models, indicating that the adsorption process might be controlled by chemisorption. The affinity of ferrihydrite toward CIP was greater than that toward LEV, which was ascribed to the higher hydrophobicity of CIP than LEV. Both surfactants enhanced antibiotic adsorption owing to SDS or SDBS molecules as bridge agents between ferrihydrite particles and antibiotics. Interestingly, the extent of the enhanced effects of surfactants on antibiotic adsorption declined as the background solution pH increased from 5.0 to 9.0, which was mainly due to the weaker hydrophobic interactions between antibiotics and the adsorbed surfactants on the iron oxide surfaces as well as the greater electrostatic repulsion between the anionic species of antibiotics and the negatively charged ferrihydrite particles at higher pH. Together, these findings emphasize the importance of widespread surfactants for illustrating the interactions between fluoroquinolone antibiotics and iron oxide minerals in the natural environment.

Spatial Distribution and Risk Assessment of Antibiotics in 15 Pharmaceutical Plants in the Pearl River Delta

Pharmaceutical plants are an essential source of antibiotics emitted into the aqueous environment. The monitoring of target antibiotics in pharmaceutical plants through various regions is vital to optimize contaminant release. The occurrence, distribution, removal, and ecological risk of 30 kinds of selected antibiotics in 15 pharmaceutical plants in the Pearl River Delta (PRD) were investigated in this study. Lincomycin (LIN) showed the highest concentration (up to 56,258.3 ng/L) in the pharmaceutical plant influents from Zhongshan city. Norfloxacin (NFX) showed a higher detection frequency than other antibiotics. In addition, the spatial distribution of antibiotics in pharmaceutical plants showed significant differences, with higher concentrations of total antibiotics found in pharmaceutical plant influents in Shenzhen City than those of different regions in PRD. The treatment processes adopted by pharmaceutical plants were commonly ineffective in removing antibiotics, with only 26.7% of antibiotics being effectively removed (average removal greater than 70%), while 55.6% of antibiotics had removal rates of below 60%. The anaerobic/anoxic/oxic (AAO)-membrane bioreactor (MBR) combined process exhibited better treatment performance than the single treatment process. Sulfamethoxazole (SMX), ofloxacin (OFL), erythromycin-H₂O (ETM-H₂O), sulfadiazine (SDZ), sulfamethazine (SMZ), norfloxacin (NFX), and ciprofloxacin (CIP) in pharmaceutical plant effluents posed high or moderate ecological risk and deserve particular attention.

The Effect of Quinolones on Common Duckweed Lemna minor L., a Hydrophyte Bioindicator of Environmental Pollution

Plant growth and the development of morphological traits in plants are inhibited under exposure to pharmaceuticals that are present in soil and water. The present study revealed that moxifloxacin (MOXI), nalidixic acid (NAL), levofloxacin (LVF) and pefloxacin (PEF) at concentrations of >0.29, >0.48, >0.62 and >1.45 mg × L^-1, respectively, inhibited the growth (Ir) of duckweed plants and decreased their yield (Iy). In the current study, none of the tested quinolones (QNs) at any of the examined concentrations were lethal for common duckweed plants. However, at the highest concentration (12.8 mg × L^-1), LVF increased Ir and Iy values by 82% on average and increased the values of NAL, PEF and MOXI by 62% on average. All tested QNs led to the loss of assimilation pigments. In consequence, all QNs, except for LVF, induced changes in chlorophyll fluorescence (Fv/Fm), without any effect on phaeophytinization quotient (PQ) values. The uptake of NAL, MOXI, LVF by Lemna minor during the 7-day chronic toxicity test was directly proportional to drug concentrations in the growth medium. Nalidixic acid was absorbed in the largest quantities, whereas in the group of fluoroquinolones (FQNs), MOXI, LVF and PEF were less effectively absorbed by common duckweed. This study demonstrated that biosorption by L. minor occurs regardless of the plants' condition. These findings indicate that L. minor can be used as an effective biological method to remove QNs from wastewater and water and that biosorption should be a mandatory process in conventional water and wastewater treatment.

Multifunctional Portable System Based on Digital Images for In-Situ Detecting of Environmental and Food Samples

The development of a portable device created by 3D printing for colorimetric and fluorometric measurements is an efficient tool for analytical applications in situ or in the laboratory presenting a wide field of applications in the environmental and food field. This device uses a light-emitting diode (LED) as radiation source and a webcam as a detector. Digital images obtained by the interaction between the radiation source and the sample were analyzed using a programming language developed in Matlab (Mathworks Inc., Natick, MA, USA), which builds the calibration curves in real-time using the RGB colour model. In addition, the entire system is connected to a notebook which serves as an LED and detector power supply without the need for any additional power source. The proposed device was used for the determination in situ of norfloxacin, allura red, and quinine in water and beverages samples, respectively. For the validation of the developed system, the results obtained were compared with a conventional spectrophotometer and spectrofluorometer respectively with a t-test at a 95% confidence level, which provides satisfactory precision and accuracy values.

Seasonal distribution and dynamic evolution of antibiotics and evaluation of their resistance selection potential and ecotoxicological risk at a wastewater treatment plant in Jinan, China

The seasonal distribution and dynamic evolution of antibiotics in wastewater from main treatment areas and in sludge and their resistance selection potential and ecotoxicological risk were studied at a municipal wastewater treatment plant in Jinan, East China. Ten antibiotics were selected, and all were detected in wastewater and sludge samples, with fluoroquinolones showing the highest detection concentrations and frequencies. Seasonal fluctuations in the antibiotic concentrations in the influent, effluent, and sludge were observed, with the highest values in winter in most cases. The dynamic evolution of antibiotics during the treatment process differed among the seasons. The antibiotic removal efficiencies were incomplete, ranging from - 40.47 to 100%. Mass balance analysis showed that sulfonamides, roxithromycin, and metronidazole were mainly removed through biological processing, whereas fluoroquinolones, doxycycline, and chloramphenicol were removed through sludge adsorption. Levofloxacin, as well as a mixture of the 10 antibiotics from the effluent, could pose a low ecotoxicological risk to Daphnia in the receiving waters. Additionally, levofloxacin and ciprofloxacin in the effluent and ciprofloxacin and metronidazole in the sludge may facilitate the selection of antibiotic-resistant bacteria in the environment.

Wet oxidation and catalytic wet oxidation of pharmaceutical sludge

In this work, wet oxidation and catalytic wet oxidation of pharmaceutical sludge using homogeneous and heterogeneous catalysts were investigated. The results indicate that wet oxidation is a promising method for the highly efficient degradation of pharmaceutical sludge. Under optimal conditions, the highest removal efficiencies of volatile suspended solids (VSS) 86.8% and chemical oxygen demand (COD) 62.5% were achieved at 260 °C for 60 min with an initial oxygen pressure of 1.0 MPa. NaOH exhibited excellent acceleration performance on the VSS removal. The highest VSS removal efficiency of 95.2% was obtained at 260 °C for 60 min with an initial oxygen pressure of 1.0 MPa and 10 g·L^-1 of NaOH. By using a Cu-Ce/γ-Al₂O₃ catalyst, the highest removal rates of VSS 87.3% and COD 72.6% were achieved at 260 °C for 60 min with an initial oxygen pressure of 1.0 MPa and 10 g·L^-1 of catalyst. The wet oxidation reaction can be maintained itself owing to the exothermic heat. The produced low-molecular-weight carboxylic acids have potential commercial utilization as organic carbon sources in the biological wastewater treatment processes. The inorganic residues can be utilized for the building materials production. These results implied that the catalytic wet oxidation is a promising method for the volume reduction and resource utilization of pharmaceutical sludge.

Evaluation of growth and antioxidant responses of freshwater microalgae Chlorella sorokiniana and Scenedesmus dimorphus under exposure of moxifloxacin

As one of the fourth-generation fluoroquinolone antibiotics, moxifloxacin (MOX) has been frequently released to the aquatic environment, threatening local organisms. However, researches on its ecotoxicity to aquatic organisms are still limited. This study analyzed effects of MOX on the growth, photosynthesis and oxidative stress of two common types of freshwater microalgae, Chlorella sorokiniana and Scenedesmus dimorphus. The 96 h-EC₅₀ values of MOX for C. sorokiniana and S. dimorphus were 28.42 and 26.37 mg/L, respectively. Although variations of specific indicators for photosynthetic fluorescence intensity were different, photosystems of two types of microalgae were irreversibly damaged. The malondialdehyde content and superoxide dismutase of C. sorokiniana and S. dimorphus evidently increased, indicating that the exposure of MOX caused serious oxidative stress. Chlorophyll a, b and carotenoids contents of C. sorokiniana increased, probably resulting from the resistance to oxidative stress, whereas they were inhibited due to oxidation damage as for S. dimorphus. Risk quotients (RQs) of MOX for C. sorokiniana and S. dimorphus in wastewater were 7.882 and 8.495, respectively, which demonstrated that MOX had a considerable risk to aquatic environment, especially in the context of its increasing use in practice.

Emergent crisis of antibiotic resistance: A silent pandemic threat to 21st century

Antibiotic resistance has become an indispensably alarming menace to the global community. The primary factors are overuse and abuse of antibiotics, lack of novel medicines under development, the health care industry's focus on profit, and the absence of diagnostic testing prior to the prescription of antibiotics. Additionally, over the past few decades, the main factors contributing to the global spread of antibiotic resistance have been the overuse of antibiotics in livestock and other animals, drug efficacy, development of fewer new vaccines, environmental toxicity, transmission through travel, and lack of funding for healthcare research and development. These factors have accelerated resistance in microorganisms through structural and functional modifications in bacteria such as reduced drug permeability, increased efflux pumps, enzymatic antibiotic modification, and change in drug target, intracellular infection, and biofilm creation. There has been an increase in resistance during the pandemic and among cancer patients due to improper prescriptions. A number of modern therapeutic alternatives have been developed to curb widespread antibiotic resistance such as nanoparticle, bacteriophage, and antimicrobial biochemical approaches. It is high time to explore new alternatives to curtail enormous increase in resistant pathogens which could be an incurable global confrontation. This review highlights the complete insight on the global drivers of resistance along with the modes of action and impacts, finally discussing the latest therapeutic alternatives.

Different responses of representative denitrifying bacterial strains to gatifloxacin exposure in simulated groundwater denitrification environment

The impact of antibiotics on denitrification in the ecological environment has attracted widespread attention. However, the concentration threshold and inhibitory effect of the same antibiotic on denitrification mediated by mixed denitrifying microbes were conflicting in some studies. In this study, Paracoccus denitrificans, Acidovorax sp., and Pseudomonas aeruginosa were selected as representative denitrifying bacterial strains to explore the response of a single strain to gatifloxacin (GAT) exposure in groundwater denitrification. The results showed that the nitrate and nitrite removal efficiencies of Pseudomonas aeruginosa decreased by 34.87-36.25 % and 18.27-23.31 %, respectively, with exposure to 10 μg/L GAT, accompanied by a significant decline in denitrifying enzyme activity and gene expression. In contrast, the elevated denitrifying enzyme activity and gene expression of Paracoccus denitrificans promoted its nitrate and nitrite reduction by 2.09-10.00 % and 0-8.44 %, respectively. Additionally, there were no obvious effects on the removal of nitrate and nitrite by Acidovorax sp. in the presence of 10 μg/L GAT, which was consistent with the variation in denitrifying enzyme activity and total gene expression levels. The fit results of the Monod equation and its modification further elucidated the nitrate degradation characteristics from the perspective of denitrification kinetics. Furthermore, antibiotic resistance gene (ARG) analysis showed that the addition of 10 μg/L GAT (approximately 30 days) did not observably increase the relative abundance of ARGs. This study provides some preliminary understanding of the response differences of representative denitrifying bacterial strains to antibiotic exposure in groundwater denitrification.

An exhaustive investigation on antibiotics contamination from livestock farms within sensitive reservoir water area: Spatial density, source apportionment and risk assessment

Although the studies on antibiotic contamination are common at present, large-scale sampling studies drawing highly representative conclusions are still scarce. This study conducted a comprehensive investigation on a total of 1183 samples from 70 livestock farms within a sensitive area around reservoir waters. 45 types of antibiotics belonging to 5 different classes were monitored. This is the first analysis to comprehensively investigate the density distribution, source apportionment, ecological and health risk of antibiotics in an entire area of sensitive waters. The results showed that the layer manure samples had highest detection rate of antibiotics (0.0 %-96.1 %, average value = 30.7 %) followed by pig manure samples. Oxytetracycline had the highest concentration of 712.16 mg/kg in a pig manure sample. Different from using antibiotic concentration as a proxy for pollution level, the spatial density was calculated by averaging antibiotic concentration to area and converting different livestock to pig equivalent. The spatial density of pig equivalent can more realistically reflect the pollution caused by different breeds of livestocks. It was shown that the pig farms contributed higher to total antibiotic density than the layer and cattle farms did. After assessed, a few antibiotics (oxytetracycline, chlorotetracycline and tetracycline) have posed high ecological risks to soil around the farms. However, none of them caused hazard quotient (HQ) risk and carcinogenic risk (CR) to human health in the water of reservoir. Children were more likely to be at hazard risk than adults. Antibiotic mass fluctuation rules were analyzed along the chain (feed → livestock waste → soil → surface water). Feed, livestock waste and soil had similar diversity, but the antibiotic concentrations continued to decline, implying the possible sources of antibiotic residues were similar. Thus, it is important to reduce unnecessary antibiotic use to prevent the potential long-term risk of antibiotics.

Deciphering the internal mechanisms of ciprofloxacin affected anaerobic digestion, its degradation and detoxification mechanism

Ciprofloxacin (CIP) is widely used in livestock farms, but the internal mechanism of the effect of residual CIP in actual livestock wastewater on anaerobic digestion (AD) performance remains unknown. This study examined the dose-specific effects of CIP (0.5-2 mg/L) on livestock wastewater AD by analyzing acidogenesis and methanogenesis. 0.5 mg/L CIP promoted methane production by facilitating acidogenesis and acetogenesis. Compared with the control, the cumulative methane production increased from 331.38 to 407.44 mL/g VS at a dose of 0.5 mg/L, an increase of 22.95 %. However, as the dose of CIP increased, the cumulative methane production gradually decreased to 217.64 mL/g VS (2 mg/L). Microbial community analysis revealed that CIP had the greatest impact on methane production by influencing the activity of acidogenic bacteria. Meanwhile, acidogenesis was critical for CIP degradation. In acidogenesis, hydroxylation, amination, defluorination, decarboxylation, and piperazine ring breaking not only degraded CIP but also reduced its toxicity. Therefore, a large number of intermediates could be continuously degraded by microorganisms. However, as the dosage of CIP increased, the ability of microorganisms to degrade intermediates decreased.

Metronidazole Degradation by UV and UV/H2O2 Advanced Oxidation Processes: Kinetics, Mechanisms, and Effects of Natural Water Matrices

Advanced oxidation technology represented by hydroxyl radicals has great potential to remove residual antibiotics. In this study, we systematically compared the metronidazole (MTZ) degradation behavior and mechanism in the UV and UV/H₂O₂ systems at pH 3.00 condition. The results show that the initial reaction rates were 0.147 and 1.47 µM min^-1 in the UV and UV/H₂O₂ systems, respectively. The main reason for the slow direct photolysis of MTZ is the relatively low molar absorption coefficient (2645.44 M^-1 cm^-1) and quantum yield (5.9 × 10^-3 mol Einstein^-1). Then, we measured kMTZ,OH&nbsp;• as 2.79 (±0.12) × 10⁹ M^-1 s^-1 by competitive kinetics, and calculated kMTZ,OH&nbsp;• and [OH&nbsp;•]SS as 2.43 (±0.11) × 10⁹ M^-1 s^-1 and 2.36 × 10^-13 M by establishing a kinetic model based on the steady-state hypothesis in our UV/H₂O₂ system. The contribution of direct photolysis and ^•OH to the MTZ degradation was 9.9% and 90.1%. ^•OH plays a major role in the MTZ degradation, and ^•OH was the main active material in the UV/H₂O₂ system. This result was also confirmed by MTZ degradation and radicals' identification experiments. MTZ degradation increases with H₂O₂ dosage, but excessive H₂O₂ had the opposite effect. A complex matrix has influence on MTZ degradation. Organic matter could inhibit the degradation of MTZ, and the quenching of the radical was the main reason. NO3- promoted the MTZ degradation, while SO42- and Cl^- had no effect. These results are of fundamental and practical importance in understanding the MTZ degradation, and to help select preferred processes for the optimal removal of antibiotics in natural water bodies, such as rivers, lakes, and groundwater.

Decentralized systems for the treatment of antimicrobial compounds released from hospital aquatic wastes

In many developing countries, untreated hospital effluents are discharged and treated simultaneously with municipal wastewater. However, if the hospital effluents are not treated separately, they pose concerning health risks due to the possible transport of the antimicrobial genes and microbes in the environment. Such effluent is considered as a point source for a number of potentially infectious microorganisms, waste antimicrobial compounds and other contaminants that could promote antimicrobial resistance development. The removal of these contaminants prior to discharge reduces the exposure of antimicrobials to the environment and this should lower the risk of superbug development. At an effluent discharge site, suitable pre-treatment of wastewater containing antimicrobials could maximise the ecological impact with potentially reduced risk to human health. In addressing these points, this paper reviews the applications of decentralized treatment systems toward reducing the concentration of antimicrobials in wastewater. The most commonly used techniques in decentralized wastewater treatment systems for onsite removal of antimicrobials were discussed and evidence suggests that hybrid techniques should be more useful for the efficient removal of antimicrobials. It is concluded that alongside the cooperation of administration departments, health industries, water treatment authorities and general public, decentralized treatment technology can efficiently enhance the removal of antimicrobial compounds, thereby decreasing the concentration of contaminants released to the environment that could pose risks to human and ecological health due to development of antimicrobial resistance in microbes.

Higher spreading risk of antibacterial biocide and heavy metal resistance genes than antibiotic resistance genes in aerobic granular sludge

Metagenomic approach was applied to simultaneously reveal the antibiotic resistance genes (ARGs) and antibacterial biocide & metal resistance genes (BMRGs), and the corresponding microbial hosts with high mobility during aerobic granular sludge (AGS) formation process. The results showed that the relative abundance of BMRGs was 88-123 times that of ARGs. AGS process was easier to enrich BMRGs, leading to a greater risk of drug resistance caused by BMRGs than that by ARGs. The enrichments of ARGs and BMRGs in AGS were closely related to several enhanced microbial metabolisms (i.e., cell motility, transposase and ATP-binding cassette transporters) and their corresponding regulatory genes. Several enhanced KEGG Orthologs (KO) functions, such as K01995, K01996, K01997 and K02002, might cause a positive impact on the spread of ARGs and BMRGs, and the main contributors were the largely enriched glycogens accumulating organisms. The first dominant ARGs (adeF) was carried by lots of microbial hosts, which might be enriched and propagated mainly through horizontal gene transfer. Candidatus Competibacter denitrificans simultaneously harbored ARG (cmx) and Cu related RGs (corR). Many enriched bacteria contained simultaneously multiple BMRGs (copR and corR) and mobile genetic elements (integrons and plasmids), granting them high mobility capabilities and contributing to the spread of BMRGs. This study might provide deeper understandings of the proliferation and mobility of ARGs and BMRGs, importantly, highlighted the status of BMRGs, which laid the foundation for the controlling widespread of resistance genes in AGS.

Antibiotics and antibiotic resistant bacteria/genes in urban wastewater: A comparison of their fate in conventional treatment systems and constructed wetlands

There is a growing concern that the use and misuse of antibiotics can increase the detection of antibiotic resistant genes (ARGs) in wastewater. Conventional wastewater treatment plants provide a pathway for ARGs and antibiotic resistant bacteria (ARB) to be released into natural water bodies. Research has indicated that conventional primary and secondary treatment systems can reduce ARGs/ARB to varying degrees. However, in developing/low-income countries, only 8-28% of wastewater is treated via conventional treatment processes, resulting in the environment being exposed to high levels of ARGs, ARB and pharmaceuticals in raw sewage. The use of constructed wetlands (CWs) has the potential to provide a low-cost solution for wastewater treatment, with respect to removal of nutrients, pathogens, ARB/ARGs either as a standalone treatment process or when integrated with conventional treatment systems. Recently, CWs have also been employed for the reduction of antibiotic residues, pharmaceuticals, and emerging contaminants. Given the benefits of ARG removal, low cost of construction, maintenance, energy requirement, and performance efficiencies, CWs offer a promising solution for developing/low-income countries. This review promotes a better understanding of the performance efficiency of treatment technologies (both conventional systems and CWs) for the reduction of antibiotics and ARGs/ARB from wastewater and explores workable alternatives.

Fast photo-Fenton-like oxidation in bismuth catalysis: A novel Fe(III) self-doped sodium bismuthate nanosheet

Sodium bismuthate dihydrate (NaBiO₃.2 H₂O, NBH) nanosheets were successfully prepared in this study using the persulfate oil bath oxidation method. Benefited from the unique layered structure of NBH, the Fe(III) as a variable valence metal ion was explored for enhancing NBH activation of peroxymonosulfate (PMS) to degrade levofloxacin (LVF) in the visible-light catalytic system. Based on results of the reactive oxygen species (ROS) quenching experiments and electron paramagnetic resonance (EPR) analysis, singlet oxygen (¹O₂) and superoxide radical (O₂^·-) were identified as the main ROS. The morphology, chemical structure, and optical properties of NBH were analyzed using various characterization methods. It was confirmed that Fe(III) embedded in the NBH via the ion exchange with Na, resulting in lattice oxygen vacancies on the surface of the NBH, after the formation of oxygen defect sites, reacts with PMS in the solution to produce active oxygen species with oxidizing efficiency. This study expands the technological application of NBH in the catalytic oxidation of variable valence metals, which are essential for the removal of fluoroquinolone antibiotics.

Toxicity, biodegradation of moxifloxacin and gatifloxacin on Chlamydomonas reinhardtii and their metabolic fate

The novel fourth-generation fluoroquinolones (FQs) were developed to improve the antimicrobial activity and their utilization has rapidly increased in recent years. However, knowledge of the ecotoxicity and microalgae-mediated biodegradation of these novel FQs is limited. In this research, the toxic effects of moxifloxacin (MOX) and gatifloxacin (GAT) on Chlamydomonas reinhardtii as well as their biodegradation and metabolic fate were investigated. The results showed that the toxicity of MOX to C. reinhardtii was higher than that of GAT, and increased with culture time. Chlorophyll fluorescence and pigment content analyses suggested that the decrease in photosynthetic efficiency was primarily caused by the inhibition of electron transport after Q_A in PSII complex. These FQs induced oxidative damage in cells, and the antioxidation mechanisms of C. reinhardtii were analyzed. The maximum MOX removal of 77.67% by C. reinhardtii was achieved at 1 mg/L MOX, whereas the maximum GAT removal of 34.04% was attained at 20 mg/L GAT. The different hydrophilicity and lipophilicity of these FQs resulted in distinct findings in biodegradation experiments. Identification of the transformation products suggested that the likely biodegradation pathways of FQs by C. reinhardtii were hydroxylation, demethylation, and ring cleavage.

Degradation of ofloxacin by potassium ferrate: kinetics and degradation pathways

Drug residues, including various antibiotics, are being increasingly detected in aqueous environments. Ofloxacin (OFX) is one such antibiotic that is widely used in the treatment of several bacterial infections; however, chronic exposure to this antibiotic can have adverse impacts on human health. Hence, the identification of an effective OFX degradation method is essential. Thus, in this study, the degradation performance of OFX using potassium ferrate (Fe(VI)) under the influence of different initial concentrations, pH, temperature, and common ions in water was investigated. OFX degradation by Fe(VI) was directly proportional to the concentration of Fe(VI) and temperature and inversely proportional to the pH. Among the common ions in water, Fe³⁺ and NH₄⁺ could significantly promote the degradation of OFX by Fe(IV), while humic acid (HA) significantly inhibited it. Under the conditions of [Fe(VI)]:[OFX] = 15:1, T = 25℃, and pH = 7.0, the removal efficiency of 8 μM OFX reached more than 90% in 4 min. Seven intermediates were identified by quadrupole time-of-flight tandem ultra-performance liquid chromatography mass spectrometry (Q-TOF LC/MS), and two possible pathways for the degradation of OFX by Fe(VI) were proposed. Overall, the results suggest that advanced oxidation technology using Fe(VI) is effective for treating wastewater containing OFX.

Enhanced Dewatering of Activated Sludge by Skeleton-Assisted Flocculation Process

Sludge dewatering is the fundamental process of sludge treatment. Environmentally friendly and efficient sludge conditioning methods are the premises of sludge to achieve dehydration reduction and resource utilization. In response to sewage plant sludge dehydration, fly ash (FA), polymerized aluminum chloride (PAC), and polymer sulfate (PFS) were studied separately to determine their sludge dehydration performance, and the effects of these three conditioner composite regulations on sludge dehydration properties were studied. Compared to the sludge treated only with conditioner, the average particle size of floc increased and the organic matter content in the filtrate decreased. The sludge dewatering efficiency after the conditioning effect is better than that after conditioning a single conditioner. After PFS conditioning with fly ash, the water content and specific resistance (SRF) of the sludge cake can be reduced to 76.39% and 6.63 × 10¹⁰ m/kg, respectively. The moisture content and specific resistance (SRF) of the sludge cake can be reduced to 76.10% and 6.91 × 10¹⁰ m/kg, respectively. The pH of the sludge and filtrate changed slightly after PAC conditioning with fly ash coupling. These results indicate that fly-ash coupled with PAC and fly-ash coupled with PFS are expected to become a novel and effective environmental protection combined conditioning method for sludge dewatering.

Diclofenac removal from the wastewater using activated sludge and analysis of multidrug resistant bacteria from the sludge

Diclofenac is an anti-inflammatory drug and has been frequently detected from the wastewater. In the present study, factors affecting diclofenac adsorption on sewage sludge was evaluated. At 1 mg/L initial diclofenac concentration, more than 80% diclofenac removal was achieved. Adsorption increased at higher concentration (100 mg/L concentration) and more than 99% diclofenac was adsorbed from the wastewater. Significant removal of diclofenac was observed after 5 min contact time. The adsorption efficacy was more than 98% after 50 and 60 min. Pseudo-first and second order kinetics revealed reasonable regression value (0.9) indicated that the model is best fitted. Diclofenac adsorption was extremely high at acidic pHs than alkaline range. The sludge samples showed the presence of multi drug resistant bacteria. Vancomycin-resistant enterococcus stains were 27%, Methicillin-resistant Staphylococcus aureus positive strains were 16.5% and Extended-spectrum betal-lactamase-harbouring Enterobacteriacea were 65.4% in the sludge. The drug resistance Enterobacteriaceae revealed 14 Klebsiella pneumonia strains, 11 strains from E. coli and two from the genus Enterobacter. To conclude, the activated sludge could be effectively utilized for the removal of diclofenac from wastewater.

Behaviour of 27 selected emerging contaminants in vertical flow constructed wetlands as post-treatment for municipal wastewater

Six substrates (i.e. sand enriched with activated or non-activated biochar or zeolite in different ratios) were tested in Vertical Flow Constructed Wetlands (VFCWs) planted with Phragmites australis and Iris pseudacorus for the removal of 27 emerging contaminants from municipal wastewater. The laboratory investigation under controlled conditions (spiked constant concentrations in synthetic wastewater) lasted 357 days and proved VFCWs being able to provide excellent effluent quality in terms of both macro - and micropollutant elimination. Because overall removal efficiencies exceeded 90% in most of the cases, significant differences among the substrates were not detectable. For compounds with medium elimination (i.e. AMPA) the type of substrate seemed to play a strong role and the maximum amount of active ingredient adsorbed per amount of substrate has been quantified (i.e. 0.77 μg of AMPA per g of 30% biochar mixed with sand). Three of the most promising substrates from laboratory where thus selected to be tested under real conditions (fluctuation in concentration, variable temperature). As result, VFCWs with 15% activated biochar mixed with sand proved to be effective in the removal of 18 emerging contaminants and complying with national discharge standards for 4 selected compounds.

Propagation of antibiotic resistance genes during anaerobic digestion of thermally hydrolyzed sludge and their correlation with extracellular polymeric substances

The positive impact of the thermal hydrolysis process (THP) of sewage sludge on antibiotic resistance genes (ARGs) removal during anaerobic digestion (AD) has been reported in the literature. However, little information is available on how changes in different extracellular polymeric substances (EPS) due to THP can influence ARG propagation during AD. This study focused on systematically correlating EPS components and ARG abundance in AD of sewage sludge pretreated with THP (80 °C, 110 °C, 140 °C, 170 °C). THP under different conditions improved sludge solubilization followed by improved methane yields in the biochemical methane potential (BMP) test. The highest methane yield of 275 ± 11.5 ml CH₄/g COD was observed for THP-140 °C, which was 40.5 ± 2.5% higher than the control. Increasing THP operating temperatures showed a non-linear response of ARG propagation in AD due to the rebound effect. The highest ARGs removal in AD was achieved with THP at 140 °C. The multivariate analysis showed that EPS polysaccharides positively correlated with most ARGs and integrons, except for macrolides resistance genes. In contrast, EPS protein was only strongly correlated with β-lactam resistance genes. These results suggest that manipulating THP operating conditions targeting specific EPS components will be critical to effectively mitigating the dissemination of particular ARG types in AD.

Anaerobic treatment of swine manure under mesophilic and thermophilic temperatures: Fate of veterinary drugs and resistance genes

The effect of anaerobic treatment of swine manure at 35 °C (mesophilic) and 55 °C (thermophilic) on methane production, microbial community and contaminants of emerging concern was investigated. Pasteurization pretreatment and post treatment was also investigated in combination with anaerobic treatment at 35 °C. Specific methane production (SMP), 26 pharmaceutical compounds (PhACs) and five antibiotic resistance genes (ARGs) (qnrS, tetW, ermB, sul1 and bla_TEM) were evaluated. Mesophilic treatment resulted in the highest SMP regardless of whether pasteurization was applied. Marbofloxacin was the most abundant antibiotic in swine manure. In general, all groups of PhACs showed higher removals under thermophilic temperatures as compared to mesophilic. In general, pasteurization pretreatment followed by mesophilic anaerobic digestion provided the highest removals of ARGs. Finally, the genera Streptococcus, Clostridium and Pseudomonas which contain pathogenic species, were present in the swine manure. Streptococcus, which was the most abundant, was decreased during all the treatments, while the others only decreased under certain treatments.

Motivation of reactive oxygen and nitrogen species by a novel non-thermal plasma coupled with calcium peroxide system for synergistic removal of sulfamethoxazole in waste activated sludge

Large amounts of antibiotics are concentrated in waste activated sludge (WAS) and released into the environment. It is thus critical to develop advanced sludge treatment technology to remove these antibiotics. Dielectric barrier discharge (DBD) combined with calcium peroxide (CaO₂), as an innovative technology to attenuate sulfamethoxazole (SMX) in sludge, was investigated. Evident synergistic effects between DBD and CaO₂ were observed on the SMX degradation with a synergistic factor of 2.02. Moreover, the energy consumption of DBD/CaO₂ was significantly lower than that of DBD alone. At a typical CaO₂ dosage of 0.1 g/g TS and discharge power of 64.5 W, the highest SMX removal of 96% was achieved within 50 min. The synergistic effects of DBD/CaO₂ could be associated with the base catalysis of H₂O₂ and O₃, UV-base-photolysis, peroxone oxidation, and photocatalytic H₂O₂. DBD/CaO₂ generated various reactive oxygen species (ROS) and nitrogen species (RNS) that participated in SMX removal. The contributions of these reactive species followed the sequence of e^- > •OH > •O₂^- > ¹O₂ > ONOO^-. Based on the detected transformation by-products and their variations during treatment, a plausible SMX degradation pathway in sludge was proposed. Besides, DBD/CaO₂ also promoted sludge disintegration, dewatering, heavy metal removal, sludge reduction, sludge solubilization, and acetate-enriched volatile fatty acid (VFA) production. Therefore, DBD/CaO₂ exhibited great potential for controlling antibiotic, as well as promoting sludge reduction, decontamination, and resourcization.