A review on advanced oxidation processes for the removal of taste and odor compounds from aqueous media

Nanobubble-enabled foam fractionation to remove algogenic odorous micropollutants

Due to climate change and environmental pollution, natural lakes and reservoir water suffer increasingly serious algal blooms and associated water quality problems due to the presence of algal or algogenic organic matter (AOM) such as algal odour and toxins. Effective removal of these micropollutants, especially in the event of algal blooms, is critical to aesthetic values of water bodies, drinking water security and human health. The study investigated the removal efficiency of two common odorous compounds, trans-1,10-dimethyl-trans-9-decalol (geosmin) and 2-Methylisoborneol (2-MIB), using foam fractionation enabled by air nanobubbles with addition of two common cationic and anionic surfactants, sodium dodecyl sulfate (SDS) and cetyltrimethylammonium bromide (CTAB), to enhance foaming ability and stability. The results showed that the cationic surfactant (i.e., CTAB), a low pH, and high ionic strength significantly promoted the removal of geosmin and 2-MIB. For example, the removal tests using the synthetic water determined that the conditions of pH = 7, [CTAB] = 20 mg·L-1 and IS = 10 mM as NaCl resulted in both the highest geosmin removal rate of 91.81% and highest 2-MIB removal rate of 85.0%. The removal of two odorous compounds in real lake water was evaluated, which yielded removal rates of 83.2% for geosmin and 48.1% for 2-MIB, highlighting the minor inhibition from water matrixes on the removal performances. Compared to microbubbles, nanobubbles enabled greater surface areas of foam and higher removal efficiencies. The study provided new insights into the use of foam fractionation with air nanobubbles to enhance the removal of odorous compounds from impaired water and mitigate the negative environmental and health impacts of harmful algal blooms (HABs).

Ignored microbial-induced taste and odor in drinking water reservoirs: Novel insight into actinobacterial community structure, assembly, and odor-producing potential

The presence of actinobacteria in reservoirs can lead to taste and odor issues, posing potential risks to the safety of drinking water supply. However, the response of actinobacterial communities to environmental factors in drinking water reservoirs remains largely unexplored. To address this gap, this study investigated the community structure and metabolic characteristics of odor-producing actinobacteria in water reservoirs across northern and southern China. The findings revealed differences in the actinobacterial composition across the reservoirs, with Mycobacterium sp. and Candidatus Nanopelagicus being the most prevalent genera. Notably, water temperature, nutrient levels, and metal concentrations were associated with differences in actinobacterial communities, with stochastic processes playing a major role in shaping the community assembly. In addition, three strains of odor-producing actinobacteria were cultured in raw reservoir water, namely Streptomyces antibioticus LJH21, Streptomyces sp. ZEU13, and Streptomyces sp. PQK19, with peak ATP concentrations of 51 nmol/L, 66 nmol/L, and 70 nmol/L, respectively, indicating that odor-producing actinobacteria could remain metabolically active under poor nutrient pressure. Additionally, Streptomyces antibioticus LJH21 produced the highest concentration of geosmin at 24.4 ng/L. These findings enhance our understanding of regional variances and reproductive metabolic mechanisms of actinobacteria in drinking water reservoirs, providing a solid foundation for improving drinking water quality control, especially for taste and odor.

Spirulina-based carbon materials as adsorbents for drinking water taste and odor control: Removal efficiency and assessment of cyto-genotoxic effects

The sensory quality of drinking water, and particularly its taste and odor (T&O) is a key determinant of consumer acceptability, as consumers evaluate water by their senses. Some of the conventional treatment processes to control compounds which impart unpleasant T&O have limitations because of their low efficiency and/or high costs. Therefore, there is a great need to develop an effective process for removing T&O compounds without secondary concerns. The primary objective of this study was to assess for the first time the effectiveness of spirulina-based carbon materials in removing geosmin (GSM) and 2-methylisoborneol (2-MIB) from water, two commonly occurring natural T&O compounds. The efficiency of the materials to remove environmentally relevant concentrations of GSM and 2-MIB (ng L-1) from ultrapure and raw water was investigated using a sensitive headspace solid-phase microextraction coupled with gas chromatography mass spectrometry (HS-SPME-GC/MS) method. Moreover, the genotoxic and cytotoxic effects of the spirulina-based materials were assessed for the first time to evaluate their safety and their potential in the treatment of water for human consumption. Based on the results, spirulina-based materials were found to be promising for drinking water treatment applications, as they did not exert geno-cytotoxic effects on human cells, while presenting high efficiency in removing GSM and 2-MIB from water.

Enhanced 2-MIB degradation by UV-LED/chlorine process: reaction kinetics, wavelength dependence, influencing factors and degradation pathways

The efficient removal of 2-Methylisoborneol (2-MIB), a typical odour component, in water treatment plants (WTPs), poses a great challenge to conventional water treatment technology due to its chemical stability. In this study, the combination of ultraviolet light-emitting diode (UV-LED) and chlorine (UV-LED/chlorine) was exploited for 2-MIB removal, and the role of ultraviolet (UV) wavelength was investigated systematically. The results showed that UV or chlorination alone did not degrade 2-MIB effectively, and the UV/chlorine process could degrade 2-MIB efficiently, following the pseudo-first-order kinetic model. The 275 nm UV exhibited higher 2-MIB degradation efficiency in this UV-LED/chlorine system than 254 nm UV, 265 nm UV and 285 nm UV due to the highest mole adsorption coefficient and quantum yield of chlorine in 275 nm UV. ·OH and ·Cl produced in the 275 nm UV/chlorine system played major roles in 2-MIB degradation. HCO3- and Natural organic matter (NOM), prevalent in water, consumed ·OH and ·Cl, thus inhibiting the 2-MIB degradation by UV-LED/chlorine. In addition, NOM and 2-MIB could form a photonic competition effect. The degradation of 2-MIB by UV-LED/chlorine was done mainly through dehydration and demethylation, and odorous intermediates, such as camphor, were produced. 2-MIB was degraded through the α bond fracture and six-membered ring opening to form saturated or unsaturated hydrocarbons and aldehydes. Four DBPs, chloroform (CF), trichloroacetaldehyde (TCE), trichloroacetone (TCP) and dichloroacetone (DCP), were mainly generated, and CF was the most significant by-product.

Synthesis, characterization, and environmental applications of graphene-coated sand: A review

Global water quality has deteriorated, leaving over 844 million individuals without access to clean drinking water. While sand filters (SF) offer a solution, their limited surface area and adsorption capacity for emerging contaminants remain a challenge. This has prompted the development of new materials such as graphene-coated sand (GCS) to enhance the sand's adsorptive properties. Notably, GCS also possesses inherent anti-bacterial properties and can function as a photocatalyst when exposed to UV and visible light, offering enhanced water purification. This manuscript 1) reviews the synthesis of GCS, detailing the characterization techniques employed to understand its structure, composition, and multifunctional properties and 2) highlights the superior efficacy of GCS in removing contaminants, including metals (>95 % removal of Cd2+, Pb2+, Zn2+, and Cu2+ in low pH environment), sulfides (full removal compared to 26 % removal by raw sand), antibiotics (98 % removal of tetracycline), and bacteria (complete cell membrane destruction), compared to traditional SF. Due to its enhanced performance and multifaceted purification capabilities, GCS presents a promising alternative to SFs, especially in developing countries, aiming to improve water quality and ensure safe drinking water access. To the best of our knowledge, no other work groups the available research on GCS. Furthermore, future research directions should focus on reducing the overall production cost of GCS, exploring surface modification techniques, and expanding the range of contaminants tested by GCS, to fully realize its potential in water purification.

Removal characteristics of 53 micropollutants during ozonation, chlorination, and UV/H2O2 processes used in drinking water treatment plant

The removal of 53 emerging micropollutants (MPs), including 10 per- and polyfluorinated substances (PFASs), 25 pharmaceuticals and personal care products (PPCPs), 7 pesticides, 5 endocrine disrupters (EDCs), 3 nitrosamines, and 3 taste and odor compounds (T&Os), by chlorination, ozonation, and UV/H2O2 treatment was examined in deionized water and surface waters used as the raw waters in drinking water treatment plants (DWTPs) in South Korea. The UV/H2O2 treatment was effective in the removal of most MPs, whereas chlorination was selectively effective for 19 MPs, including EDCs (>70 %). MPs containing aromatic ring with electron-donating functional group, or primary and secondary amines were effectively removed by chlorination immediately upon reaction initiation. The removal of MPs by ozonation was generally lower than that of the other two processes at a low ozone dose (1 mg L-1), but higher than chlorination at a high ozone dose (3 mg L-1), particularly for 16 MPs, including T&Os. Compared in deionized water, the removals of MPs in the raw water samples were lower in all three processes. The regression models predicting the rate constants (kobs) of 53 MPs showed good agreement between modeled and measured value for UV/H2O2 treatment (R2 = 0.948) and chlorination (R2 = 0.973), despite using only dissolved organic carbon (DOC) and oxidant concentration as variables, whereas the ozonation model showed a variation (R2 = 0.943). Our results can provide the resources for determining which oxidative process is suitable for treating specific MPs present in the raw waters of DWTPs.

Comparison of four pre-oxidants coupled powdered activated carbon adsorption for odor compounds and algae removal: Kinetics, process optimization, and formation of disinfection byproducts

Pre-oxidation and powdered activate carbon (PAC) are usually used to remove algae and odorants in drinking waterworks. However, the influence of interaction between oxidants and PAC on the treatment performance are scarcely known. This study systematically investigated the combination schemes of four oxidants (KMnO4, NaClO, ClO2, and O3) and PAC on the inactivation of Microcystis aeruginosa cells and removal of four frequently detected odorants in raw water (diethyl disulfide (DEDS), 2,2'-oxybis(1chloropropane) (DCIP), 2-methylisoborneol (2-MIB) and geosmin (GSM)). O3 showed highest pseudo-first-order removal rate for all four compounds and NaClO exhibited highest inactivation rates for the cell viability and Chlorophyll a (Chl-a). The Freundlich model fitted well for the adsorption of DEDS and DCIP by PAC. When treated by combined oxidation/PAC, the removal ratio of algae cells and odorants were lower (at least 1.6 times) than the sum of removal ratios obtained in oxidation or PAC adsorption alone. Among these four oxidants, the highest synchronous control efficiency of odorants (52 %) and algae (66 %) was achieved by NaClO/PAC. Prolonging the dosage time interval promoted the removal rates. The pre-PAC/post-oxidation processes possessed comparable efficiency for the removal of odorants and algae cells comparing with pre-oxidation/post-PAC process, but significantly inhibited formation of disinfection byproducts (DBPs), especially for the formation of C-DBPs (for NaClO and ClO2), bromate (for O3) and chlorate/chlorite (for ClO2). This study could provide a better understanding of improving in-situ operation of the combined pre-treatments of oxidation and PAC for source water.

Constructed electron-dense Mn sites in nitrogen-doped Mn3O4 for efficient catalytic ozonation of pyrazines: Degradation and odor elimination

In this study, N-doped Mn3O4 catalysts (Mn-nN) with electron-dense Mn sites were synthesized and employed in heterogeneous catalytic ozonation (HCO). These catalysts demonstrated excellent performance in pyrazines degradation and odor elimination. The synthesis of Mn-nN was achieved through a facile urea-assisted heat treatment method. Experimental characterization and theoretical analyses revealed that the MnN structures in Mn-nN, played a crucial role in facilitating the formation of electron-dense Mn sites that served as the primary active sites for ozone activation. In particular, Mn-1N exhibited excellent performance in the HCO system, demonstrating the highest 2,5-dimethylpyrazine (2,5-DMP) degradation efficiency. •OH was confirmed as the primary reactive oxygen species involved in the HCO process. The second-order rate constants for 2,5-DMP degradation with O3 and •OH, were determined to be (3.75 ± 0.018) × 10-1 and (6.29 ± 0.844) × 109 M-1 s-1, respectively. Seventeen intermediates were identified through GC-MS analysis during the degradation of 2,5-DMP via HCO process with Mn-1N. The degradation pathways were subsequently proposed by considering these identified intermediates. This study introduces a novel approach to synthesize N-doped Mn3O4 catalysts and demonstrates their efficacy in HCO for the degradation of pyrazines and the elimination of associated odors. The results show that the catalysts are promising for addressing odor-related environmental issues and provide valuable insights about the broader significance of catalytic ozonation processes.

Pollutants abatement in aqueous solutions with geopolymer catalysts: A photo fenton case

Environmental pollution is a serious threat to human health and the natural environment, and it has aroused widespread concern. One of the most effective processes in the removal of pollutants from wastewater is the Fenton reaction. This process is based on the production of highly reactive •OH radicals due to the rapid reaction between Iron ions and hydrogen peroxide under acidic conditions. The hydroxyl radical has a high oxidation potential of E°(•OH/H2O) = 2.8 V/SHE at acidic pH, so they are extremely reactive and non-selective oxidizing agent towards organic contaminants in wastewater. In order to avoid the drawbacks of a standard Fenton reaction, a photo Fenton reaction has been tested working at neutral pH in water in the removal of refractory pollutants. For the first time, a heterogeneous system was experimented, impregnating porous metakaolin-based geopolymers, obtained by using hydrogen peroxide and vegetable oil in different ratios, as foaming agents, with iron working as photocatalyst. The dirty wastewater as scrubber water (SCRW) and liquid fraction of digestate (LFD) were tested obtaining 40-90% abatement of Total Carbon Content.

Hydroxyl radical-driven transformations of bisphenol A and 2,4-dinitroanisole: Experimental and computational analysis

This study used experimental and computational analysis to investigate the advanced oxidation of bisphenol A (BPA) and 2,4-dinitroanisole (DNAN). The pseudo first-order reaction rate constants depended on the molar peroxide ratio and were between 0.13 and 0.28 min-1 for BPA and between 0.018 and 0.032 min-1 for DNAN. The kinetic differences appear to be due in part to the energy requirements for oxidation, which depended on the reaction mechanism but were typically lower for BPA than they were for DNAN. Density functional theory (DFT) was used to develop transformation pathways that included experimentally-detected byproducts. The most energetically favored pathway for BPA oxidation begins with the formation of hydroxylated derivatives, while for DNAN, the most energetically favorable degradation pathway begins with the substitution of the methoxy group. Overall, these findings demonstrate the power of combining experimental and computational tools to reveal transformation mechanisms during water treatment. PRACTITIONER POINTS: Advanced oxidation transformations for two emerging water pollutants, bisphenol A and dinitroanisole, was investigated. The observed reaction kinetics depended on molar peroxide ratio in a manner that is in keeping with previous findings. Density functional theory-based analysis revealed reaction energy requirements and degradation pathways.

Selective Removal of Emerging Organic Contaminants from Water Using Electrogenerated Fe(IV) and Fe(V) under Near-Neutral Conditions

Fe(IV) and Fe(V) are promising oxidants for the selective removal of emerging organic contaminants (EOCs) from water under near-neutral conditions. The Fe(III)-assisted electrochemical oxidation system with a BDD anode (Fe(III)-EOS-BDD system) has been employed to generate Fe(VI), while the generation and contributions of Fe(IV) and Fe(V) have been largely ignored. Thus, we examined the feasibility and involved mechanisms of the selective degradation of EOCs in the Fe(III)-EOS-BDD system under near-neutral conditions. It was found that Fe(III) application selectively accelerated the electro-oxidation of phenolic and sulfonamide organics and made the oxidation system be resistant to interference from Cl^-, HCO₃^-, and humic acid. Several lines of evidence indicated that EOCs were decomposed via direct electron-transfer process on the BDD anode and by Fe(IV) and Fe(V) but not Fe(VI), besides HO^•. Fe(VI) was not generated until the exhaustion of EOCs. Furthermore, the overall contributions of Fe(IV) and Fe(V) to the oxidation of phenolic and sulfonamide organics were over 45%. Our results also revealed that Fe(III) was oxidized primarily by HO^• to Fe(IV) and Fe(V) in the Fe(III)-EOS-BDD system. This study advances the understanding of the roles of Fe(IV) and Fe(V) in the Fe(III)-EOS-BDD system and provides an alternative for utilizing Fe(IV) and Fe(V) under near-neutral conditions.

Degradation of odorous 2,4,6-trichloroanisole in chlorinated water by UV-LED/chlorination: kinetics and influence factors

2,4,6-Trichloroanisole (2,4,6-TCA) has aroused a special concern for their odor problem and potential threats. In this study, the degradation of 2,4,6-TCA by UV/chlorination with different UV sources was compared, including low-pressure mercury lamp (LPUV, 254 nm) and ultraviolet light-emitting diode (UV-LED, 275 and 285 nm). The maximum removal of 2,4,6-TCA can be achieved by 275-nm UV-LED/chlorination in neutral and alkaline conditions which was 80.0%. The reaction, kinetics, and water matrix parameters on 2,4,6-TCA degradation were also evaluated. During UV-LED (275 nm)/chlorination, 2,4,6-TCA degradation was mainly caused by direct UV photolysis and indirect hydroxyl radical (HO·) oxidation, while reactive chlorine radicals (RCSs) had a negligible contribution. The second-order rate constant between HO· and 2,4,6-TCA was determined as 3.1 × 10⁹ M^-1 s^-1. Increasing initial chlorine dosage and decreasing 2,4,6-TCA concentration or pH value significantly promoted 2,4,6-TCA degradation during UV/chlorination process. The presence of natural organic matter (NOM) and bicarbonate (HCO₃^-) can inhibit 2,4,6-TCA degradation, while chloride ion (Cl^-) had a negligible effect. The kinetic model for 2,4,6-TCA degradation was established and validated, and the degradation pathways were proposed based on the identified intermediates. Furthermore, UV-LED (275 nm)/chlorination also exhibited a promising effect on 2,4,6-TCA removal in real water, which can be used to control 2,4,6-TCA pollution and odor problems.

The Role of 3D Printing in the Development of a Catalytic System for the Heterogeneous Fenton Process

Recycling of catalysts is often performed. Additive manufacturing (AM) received increasing attention in recent years in various fields such as engineering and medicine, among others. More recently, the fabrication of three-dimensional objects used as scaffolds in heterogeneous catalysis has shown innumerable advantages, such as easier handling and waste reduction, both leading to a reduction in times and costs. In this work, the fabrication and use of 3D-printed recyclable polylactic acid (PLA) scaffolds coated with an iron oxide active catalyst for Fenton reactions applied to aromatic model molecules, is presented. These molecules are representative of a wider class of intractable organic compounds, often present in industrial wastewater. The 3D-printed PLA-coated scaffolds were also tested using an industrial wastewater, determining the chemical oxygen demand (COD). The catalyst is characterized using electron microscopy coupled to elemental analysis (SEM/EDX) and thermogravimetry, demonstrating that coating leach is very limited, and it can be easily recovered and reused many times.

Electrodeionization: Principle, techniques and factors influencing its performance

Ecosystems are becoming more and more polluted, hence sustainable techniques of pollution removal are needed. In the recent times, exceedingly pure water has become ideal for several industries. Modern industry needs ultra-pure water, which is highly processed water that is devoid of colloidal particles and has a conductivity of less than 0.06 μS. A very effective method for removing ionic chemicals from polluted waters emerged recently called electrodeionization. Continuous electrodeionization (CEDI) is a technique for producing high-purity water. Besides rendering purified water, the technique has got promising wastewater treatment technologies - by facilitating the eradication of ionizable compounds, hazardous chemicals, radioactive pollutants, heavy metals and other potential contaminants. Innovative materials have been developed in order to advance and improve this technique, which would result in enormous ecological and financial benefit on a worldwide scale. In this review article, several factors that affect the performance of CEDI has been comprehended, with the impact of Ion-exchange resins and membranes as the focal point.

Smart instrumental Odour Monitoring Station for the efficient odour emission management and control in wastewater treatment plants

Odour emission assessment in wastewater treatment plants (WWTP) is a key aspect that needs to be improved in the plant management to avoid complaints and guarantee a sustainable environment. The research presents a smart instrumental odour monitoring station (SiOMS) composed of an advanced instrumental odour monitoring system (IOMS) integrated with other measurement units, for the continuous characterization and measurement of the odour emissions, with the aim of managing the potential odour annoyance causes in real time, in order to avoid negative effects. The application and on-site validation procedure of the trained IOMS is discussed. Experimental studies have been conducted at a large-scale WWTP. Fingerprint analysis has been applied to analyze and identify the principal gaseous compounds responsible for the odour annoyance. The artificial neural network has been adopted to elaborate and dynamically update the odour monitoring classification and quantification models (OMMs) of the IOMS. The results highlight the usefulness of a real-time measurement and control system to provide continuous and different information to the plant operators, thus allowing the identification of the odour sources and the most appropriate mitigation actions to be implemented. The paper provides important information for WWTP operators, as well as for the regulating bodies, authorities, manufacturers and end-users of odour monitoring systems involved in environmental odour impact management.

Management of biogenic taste and odour: From source water, through treatment processes and distribution systems, to consumers

Biogenic taste and odour (T&O) have become a global concern for water utilities, due to the increasing frequency of algal blooms and other microbial events arising from the combined effects of climate change and eutrophication. Microbially-produced T&O compounds impact source waters, drinking water treatment plants, and drinking water distribution systems. It is important to manage across the entire biogenic T&O pathway to identify key risk factors and devise strategies that will safeguard the quality of drinking water in a changing world, since the presence of T&O impacts consumer confidence in drinking water safety. This study provides a critical review of current knowledge on T&O-causing microbes and compounds for proactive management, including the identification of abiotic risk factors in source waters, a discussion on the effectiveness of existing T&O barriers in drinking water treatment plants, an analysis of risk factors for biofilm growth in water distribution systems, and an assessment of the impacts of T&O on consumers. The fate of biogenic T&O in drinking water systems is tracked from microbial production pathways, through the release of intracellular T&O by cell lysis, to the treatment of microbial cells and dissolved T&O. Based on current knowledge, five impactful research and management directions across the T&O pathway are recommended.

A detailed review on advanced oxidation process in treatment of wastewater: Mechanism, challenges and future outlook

The presence of several contaminants in waterbodies raises global pollution and creates major risks to mankind, wildlife, as well as other living organisms. Development of an effective, feasible, cost-effective and eco-friendly approach for treating wastewater that is discharged from various industries is important for bringing down the deposition of contaminants into environment. Advanced oxidation process is an efficient technique for treating wastewater owing to its advantages such as high oxidation efficacy and does not produce any secondary pollutants. Advanced oxidation process can be performed through various methods such as ozone, Fenton, electrochemical, photolysis, sonolysis, etc. These methods have been widely utilized for degradation of emerging pollutants that cannot be destroyed using conventional approaches. This review focuses on wastewater treatment using advanced oxidation process. A brief discussion on mechanism involved is provided. In addition, various types of advanced oxidation process and their mechanism are explained in detail. Challenges faced during wastewater treatment process using oxidation, electrochemical, Fenton, photocatalysis and sonolysis are discussed elaborately. Advanced oxidation process can be viewed as potential approach for treating wastewater with certain modifications and solving challenges.

COD Reduction of Aeration Effluent by Utilizing Optimum Quantities of UV/H2O2/O3 in a Small-Scale Reactor

Extensive research has been carried out to figure out safe means of disposing various industrial effluents. Industrial wastewaters from the aeration industry such as heavy metals and oily substances contain a high degree of contamination. The advanced oxidation process is one of the most effective and rapid methods of removing contaminations, which can lead to a high chemical oxygen demand (COD). The aim of the present study is to reduce the COD of an aeration effluent with the initial COD of 13,004 mg/L. About 20 sets of experimental tests were conducted to identify the contribution of H2O2, O3, and UV to the treatment process. The influence of the quantities of additives and the dose of the UV irradiance were, too, among the subjects of the study. These factors were altered throughout the experiments and their mutual effects were measured. To design the experiments, Minitab software 16 was utilized. The experimental conditions were set at the standard values of 25 °C and 1 bar to minimize any uncertainty. Based on the results, a correlation was derived, which was capable of expressing the effects of the input parameters (AOPs parameters) on the response (the COD level). Finally, the optimization process was conducted to find the quantities of H2O2, O3, and UV irradiance required to decrease the CODs of the effluent to their lowest possible. Based on the findings, when the doses of H2O2, O3, and UV to the treatment process were 40 mg/L, 8 mg/L and 86 mWs/cm2, respectively, the COD percent change was 51.5%.

Role of Sulfur Compounds in Vegetable and Mushroom Aroma

At the base of the food pyramid is vegetables, which should be consumed most often of all food products, especially in raw and unprocessed form. Vegetables and mushrooms are rich sources of bioactive compounds that can fulfill various functions in plants, starting from protection against herbivores and being natural insecticides to pro-health functions in human nutrition. Many of these compounds contain sulfur in their structure. From the point of view of food producers, it is extremely important to know that some of them have flavor properties. Volatile sulfur compounds are often potent odorants, and in many vegetables, belonging mainly to Brassicaeae and Allium (Amaryllidaceae), sulfur compounds determine their specific flavor. Interestingly, some of the pathways that form volatile sulfur compounds in vegetables are also found in selected edible mushrooms. The most important odor-active organosulfur compounds can be divided into isothiocyanates, nitriles, epithionitriles, thiols, sulfides, and polysulfides, as well as others, such as sulfur containing carbonyl compounds and esters, R-L-cysteine sulfoxides, and finally heterocyclic sulfur compounds found in shiitake mushrooms or truffles. This review paper summarizes their precursors and biosynthesis, as well as their sensory properties and changes in selected technological processes.

Nanomaterial-enabled photothermal-based solar water disinfection processes: Fundamentals, recent advances, and mechanisms

The pathogenic microorganisms in water pose a great threat to human health. Photothermal and photothermocatalytic disinfection using nanomaterials (NPs) has offered a promising and effective strategy to address the challenges in solar water disinfection (SODIS), especially in the point-of-use operations. This review aims at providing comprehensive and state-of-the-art knowledge of photothermal-based disinfection by NPs. The fundamentals and principles of photothermal-based disinfection were first introduced. Then, recent advances in developing photothermal/photothermocatalytic catalysts were systematically summarized. The light-to-heat conversion and disinfection performance of a large variety of photothermal materials were presented. Given the complicated mechanisms of photothermal-based disinfection, the attacks from reactive oxygen species and heat, the destruction of bacterial cells, and the antibacterial effects of released metal ions were highlighted. Finally, future challenges and opportunities associated with the development of cost-effective photothermal/photothermocatalytic disinfection systems were outlined. This review will provide guidance in designing future NPs and inspire more research efforts from environmental nano-communities to move towards practical water disinfection operations.

Insights into the Seasonal Olfactory Mechanism of Geosmin in Raw Water of Huangpu River

Since the 1990s, the raw water of Huangpu River in Shanghai, China, has intermittently encountered off-flavor contamination. In this work, the concentrations of typical odor, geosmin, in raw water of Huangpu River are found to shift along with the seasons. However, microbes recognized as the producer of geosmin such as Cyanobacteria and Actinobacteria are not consistent with the shift of geosmin. Cyanobacteria blooms in summer rather than winter, whereas Actinobacteria thrives in winter. Representational difference analysis (RDA) reveals that microbes associated with blooming algae have positive co-occurrence correlations with the concentrations of geosmin and nutrients in winter, whereas those within Cyanobacteria and Planctomycete are in a positive correlation with temperature and thrive in summer. This causes the concentration of geosmin in raw water to appear to depend on the abundance of Actinobacteria rather than that of Cyanobacteria. However, combining with the synthesis and storage properties of geosmin in algae, as well as the decomposition properties of algae with Actinobacteria, geosmin might be synthesized by Cyanobacteria in summer, which is stored in cells of Cyanobacteria and released only via the decomposition of Actinobacteria in winter. This potential olfactory mechanism of geosmin is quite different from that derived from pure culture of odor producers or correlation analysis of bacteria and odors; thus, providing insights into the mechanism of practical off-flavor events.

An overview on surfactants as pollutants of concern: Occurrence, impacts and persulfate-based remediation technologies

Surfactants are molecules that reduce interfacial energy and increase solubility of other pollutants in water. These properties make them suitable for various domestic and industrial applications, soil remediation, pesticide formulation, among others. The increase in their use and the lack of strict regulations regarding their disposal and management is a matter of concern and requires more attention since the release and distribution of these compounds into the environment can modify important water quality parameters. As a result of these changes, different toxicological effects to aquatic organisms are discussed and exposed herein. On this basis, we provide an overview of the classes of surfactants, as well as their occurrence in different aqueous matrices. In addition, existing regulations around the world regarding their concentration limit for different environments are discussed. Current research focuses on the application of conventional treatments, such as biological treatments; notwithstanding, more toxic and bioaccumulative products can be generated. Advanced Oxidation Processes are promising alternatives and have also been widely applied for the removal of surfactants. This study provides, for the first time, an overview of the application of persulfate-based processes for surfactants degradation based on recent literature findings, as well as the various factors related to the activation of the persulfate anions. This review also highlights the challenges and opportunities for future research to overcome the obstacles to the practical application of this process.

Mechanism study on the effect of peracetic acid (PAA), UV/PAA and ultrasonic/PAA oxidation on ultrafiltration performance during algae-laden water treatment

In this work, peracetic acid (PAA), ultraviolet (UV)/PAA and ultrasonic (US)/PAA pre-oxidation were applied to enhance ultrafiltration (UF) performance during algae-laden water treatment. The results showed that 10 mg/L PAA, exhibiting an optimal performance with membrane fouling resistance reduced by 76.26%. Low dosage of UV/PAA can effectively control fouling by enhancing the degradation of dissolved organics. Though more radicals were generated with the increasing dosage of PAA during the UV/PAA process, flux deterioration was occurred when PAA dosage over 10 mg/L, owing to a negative correlation between fouling resistance and algal integrity loss. Compared with UV, US exhibited a worse activation effect on PAA with less reactive radicals produced. Even worse, US can stimulate the stress metabolism of algal cells with slightly integrity loss, which then resulted in an exacerbation of permeate quality. Fouling mechanism analysis revealed that the delay formation of cake layer with membrane fouling alleviation mainly through efficient degradation of macromolecular organics. The investigation of synergistic and individual effect of EOM degradation, algae rupture and IOM release on the filtration performance revealed that EOM degradation was the primary mechanism for fouling control while algae rupture rather than IOM release was crucial for membrane fouling aggravation. This indicates that moderate oxidation, with property of high organic degradation and low cell rupture, was the working principal and objectives for algae-laden water treatment. Additionally, it was found that the ·OH radicals produced during UV/PAA process can efficiently degrade representative odors. In general, pretreatments of PAA and low dosages of UV/PAA showed promising prospects in improving the UF performance of algae-laden water and treating algal secretions.

Identification of Volatiles of the Dinoflagellate Prorocentrum cordatum

The dinoflagellate Prorocentrum cordatum, often called P. minimum, is a potentially toxic alga found in algal blooms. Volatile compounds released by the alga might carry important information, e.g., on its physiological state, and may act as chemical messengers. We report here the identification of volatile organic compounds emitted by two strains, xenic P. cordatum CCMP 1529 and axenic P. cordatum CCMP 1329. The volatiles released during culture were identified despite their low production rates, using sensitive methods such as open-system-stripping analysis (OSSA) on Tenax TA desorption tubes, thermodesorption, cryofocusing and GC/MS-analysis. The analyses revealed 16 compounds released from the xenic strain and 52 compounds from the axenic strain. The majority of compounds were apocarotenoids, aromatic compounds and small oxylipins, but new natural products such as 3,7-dimethyl-4-octanolide were also identified and synthesized. The large difference of compound composition between xenic and axenic algae will be discussed.

Recycling chestnut shell for superior peroxymonosulfate activation in contaminants degradation via the synergistic radical/non-radical mechanisms

The efficient recycling of agricultural chestnut shell waste is of considerable interest due to its large availability and economic feasibility. Herein, an alkaline-activated biochar was thermally prepared using chestnut shell by finely regulating main conditions; its morphological, structural and physic-chemical properties were well characterized. Fenton-like capacity to trigger peroxymonosulfate activation for superior pollutant degradation with high efficiency and good selectivity was validated in different water matrix. Both radical formation and electron transfer were identified as reaction pathways, while the selective non-radical mechanism played the major role in pollutant degradation. Surface ketonic groups were identified as the main reactive sites for non-selective radical production, while crystal edges and structural defects on sp²/sp³ carbon network could smoothly mediate the selective electron transfer from pollutant to oxidant in the non-radical Fenton-like catalysis. The two-mixed radical/non-radical pathways exhibited important advantages for environmental decontamination, in comparison with the one-single radical or non-radical mechanism. Our study provided a promising recycling strategy for agricultural chestnut shell, as well as an environment-friendly catalyst for heterogeneous Fenton-like catalysis in green water purification rendered by the synergistic radical/non-radical reaction pathways.

Mechanisms and application of the IAST-EBC model for predicting 2-MIB adsorption by PAC in authentic raw waters: Correlation between NOM competitiveness and water quality parameters

Natural organic matter (NOM) exerts negative impacts on 2-methylisoborneol (2-MIB) removal by powdered activated carbon (PAC), thus adding to the difficulty in accurate PAC dose prediction. Our study investigated the application of the ideal adsorbed solution theory-equivalent background compound (IAST-EBC) model and its simplified version for PAC dose prediction. Four raw water samples were employed, and the corresponding C_0,EBC values, indicating NOM competitiveness, were calculated. The results showed that the IAST-EBC model presented ideal predictive performance in 2-MIB adsorption under both equilibrium and nonequilibrium conditions and the C_0,EBC values of the Huangpu River (8800 ng/L) and Qiantang River (10300 ng/L) were high, representing the higher NOM competitiveness in these two rivers, which may be caused by municipal effluent and industrial wastewater discharge. In contrast, Tai Lake water showed a lower C_0,EBC value (6400 ng/L), which was likely associated with algae and other microbial activities. The fluorescence index (FI, the ratio of E_x/E_m = 370/470 nm to E_x/E_m = 370/520 nm) can be applied to estimate C_0,EBC, thus facilitating prediction. Our study also showed that the IAST-EBC model can be further simplified under lower initial 2-MIB concentrations or longer contact times, which is particularly useful for practical applications.

Electrochemical elimination of Microcystis aeruginosa with boron-doped diamond anode in different electrolyte systems: chemical and biological mechanisms

The chemical and biological mechanisms of electrochemical elimination of Microcystis aeruginosa (M. aeruginosa) using boron-doped diamond (BDD) anode were comparatively explored in three different electrolytes (chloride, sulfate, and phosphate solutions). The most efficient elimination of M. aeruginosa was observed in chloride solution, which was attributed to the greatest total long-lived oxidants from the favorable formation of active chlorine. Moreover, the high permeability of active chlorine resulted in profound intracellular damages to chlorophyll-a, microcystin-LR (MC-LR), superoxide dismutase (SOD) enzyme, and DNA in the chloride system. The change of membrane permeability and degradation of the released MC-LR induced by active chlorine were further confirmed by the increase of extracellular MC-LR in the initial 5 min and a complete decay in the subsequent 15 min, while the change in morphology of algae cells was insignificant from SEM images. In sulfate and phosphate electrolytes, membrane damages were much more pronounced based on lipid peroxidation observation, although changes in cell morphology was found more significant in phosphate system. The higher concentrations of oxidants (·OH, O₃, H₂O₂, S₂O₈^2-) generated in sulfate than in phosphate solution explained the greater efficiency of electrochemical elimination of M. aeruginosa in the sulfate electrolyte in terms of changes of cell density, OD₆₈₀, chlorophyll-a, MC-LR, lipids, SOD enzyme, and DNA.

Superior degradation of phenolic contaminants in different water matrices via non-radical Fenton-like mechanism mediated by surface-disordered WO3

Heterogeneous Fenton-like catalysis mediated by solid catalyst is a promising oxidation technology for water purification. The redox reactivity, cost-effectiveness, and environmental compatibility of solid catalyst play governing roles in oxidant activation, radical generation, and pollutant degradation. Herein, the surface-disordered WO₃ (D-WO₃) functionally engineered by the unique crystalline-amorphous core-shell structure is proven to be a superior solid catalyst of heterogeneous Fenton-like catalysis for peroxymonosulfate (PMS) activation and pollutant degradation in various water matrices. Six typical phenolic and dye pollutants are effectively and selectively degraded in the D-WO₃/PMS system with much reduced matrix effects. Both radical identifying and scavenging tests elucidate the important role of non-radical ¹O₂ and mediated electron transfer during PMS activation on the D-WO₃ surface. The superior Fenton-like activity of D-WO₃ can be mainly attributed to the surface and sub-surface distorted lattice sites with finely tailored atomic and electronic structures and surface chemistry. These distorted lattice sites can thermodynamically serve as the key reactive centers of dissociative adsorption and catalytic activation for both PMS and pollutant, with high adsorption energy, strong structural activation, and smooth electron transfer. Our findings provide a new chance for heterogeneous Fenton-like catalysis mediated by transition metal oxides with high capacity, low cost, and no toxicity for promising water purification.

Off-Flavors in Aquacultured Fish: Origins and Implications for Consumers

Off-flavors in fish and water are considered a worldwide problem. Several factors, such as the presence of phosphorus, micronutrients, and organic matter, contribute to phytoplankton proliferation and the production of off-flavors. Geosmin and 2-methylisoborneol are the most common off-flavors that confer the smell of earth or mold to water and fish. These metabolites are not considered toxic, but they can be easily transferred from water to living organisms and accumulate in the biota, up the trophic levels and to consumers, including fish species. Numerous processes have been studied to eliminate or reduce the presence of off-flavors in recirculating aquaculture systems. Managing off-flavors must be eco-friendly and consumer-friendly. Strategies against off-flavors must be efficient and low-cost. However, these solutions may be different for each fish production system. We review herein the main compounds produced by cyanobacteria that can accumulate in fish used in aquaculture that can affect the quality of food, as well as production costs and consumer preference.

Evaluation of advanced oxidation processes for β-blockers degradation: a review

This study summarizes the results of scientific investigations on the removal of the three most often used β-blockers (atenolol, metoprolol and propranolol) by various advanced oxidation processes (AOP). The free radical chemistry, rate constants, degradation mechanism and elimination effectiveness of these compounds are discussed together with the technical details of experiments. In most AOP the degradation is predominantly initiated by hydroxyl radicals. In sulfate radical anion-based oxidation processes (SROP) both hydroxyl radicals and sulfate radical anions greatly contribute to the degradation. The rate constants of reactions with these two radicals are in the 10⁹-10¹⁰ M^-1 s^-1 range. The degradation products reflect ipso attack, hydroxylation on the aromatic ring and/or the amino moiety and cleavage of the side chain. Among AOP, photocatalysis and SROP are the most effective for degradation of the three β-blockers. The operating parameters have to be optimized to the most suitable effectiveness.

Implications for emergency response to the severe odor incident occurred in source water: Potential odorants and control strategy

Sudden odor incidents occurring in the source water have been a severe problem for water suppliers. In order to apply emergency control measures effectively, it is necessary to identify the target compounds responsible for odor incidents rapidly. The present work identified the odorants and explored emergency disposal mechanisms for sudden and severe odors in the QT River's drinking water source (HZ city, China). Medicinal, chemical, septic, and musty odors with strong intensities were detected in the source water. The effect of conventional treatments of drinking water treatment plant (DWTP) on odors' removal was limited, which was evident by the presence of medicinal, chemical, and musty odors with moderate intensities in the effluent of DWTP. Total seventeen odorants were identified successfully in the source water of QT River and the effluent of DWTP. The measured OAVs and reconstituting the identified odorants explained 87, 87, 89, and 94% of medicinal, chemical, septic, and musty odors, respectively, in the source water of the QT River and 90, 87, and 88% of medicinal, chemical, and musty odors in the effluent. Styrene, phenol, 2-chlorophenol, 2-tert-butylphenol, and 2-methylphenol were associated with the medicinal odor, while propyl sulfide, diethyl disulfide, propyl disulfide, and indole were related to the septic odor. Geosmin and 2-methylisoborneol (2-MIB) were responsible for the musty odor, and cyclohexanone, 1,4-dichlorobenzene, and nitrobenzene were involved with the chemical odor. Based on the characteristics of identified odorants, powdered activated carbon (PAC) was applied to control the odors in the QT River. The results indicated that the medicinal, chemical, septic, and musty odors could be removed entirely after adding 15 mg/L PAC, which effectively controlled emergency odor problems. Overall, the study would offer a scientific basis and operational reference for emergency odor management and control in DWTP with similar complicated odor incidents.

Toward Selective Oxidation of Contaminants in Aqueous Systems

The presence of diverse pollutants in water has been threating human health and aquatic ecosystems on a global scale. For more than a century, chemical oxidation using strongly oxidizing species was one of the most effective technologies to destruct pollutants and to ensure a safe and clean water supply. However, the removal of increasing amount of pollutants with higher structural complexity, especially the emerging micropollutants with trace concentrations in the complicated water matrix, requires excessive dosage of oxidant and/or energy input, resulting in a low cost-effectiveness and possible secondary pollution. Consequently, it is of practical significance but scientifically challenging to achieve selective oxidation of pollutants of interest for water decontamination. Currently, there are a variety of examples concerning selective oxidation of pollutants in aqueous systems. However, a systematic understanding of the relationship between the origin of selectivity and its applicable water treatment scenarios, as well as the rational design of catalyst for selective catalytic oxidation, is still lacking. In this critical review, we summarize the state-of-the-art selective oxidation strategies in water decontamination and probe the origins of selectivity, that is, the selectivity resulting from the reactivity of either oxidants or target pollutants, the selectivity arising from the accessibility of pollutants to oxidants via adsorption and size exclusion, as well as the selectivity due to the interfacial electron transfer process and enzymatic oxidation. Finally, the challenges and perspectives are briefly outlined to stimulate future discussion and interest on selective oxidation for water decontamination, particularly toward application in real scenarios.

Comparative assessment of the degradation of 2-methylisoborneol and geosmin in freshwater using advanced oxidation processes

Traditional methodologies of conventional drinking water treatment are unable to remove some chemical compounds, such as those that cause odor and taste in drinking water. The present work aims to evaluate the efficiency of advanced oxidations processes, using UV radiation, O₃ and O₃ + UV in the degradation of geosmin (GSM) and 2-methylisoborneol (2-MIB) in synthetic samples. The efficiency of the processes was monitored by Gas Chromatography coupled with Mass Spectrometry using solid phase microextration technique. Experiments were carried out for 45 min with samplings every 15 min. The degradation results showed that UV radiation alone was not efficient for the degradation of both compounds. The fasted decay was observed by the combined use of O₃ and UV with an ozone concentration of 15.84 mg L^-1. Under these conditions, the final concentration of GSM was below the limit of quantification, so that approximately 99% of the initial concentration was degraded, while 2-MIB was degraded by 95%. With the same O₃ concentration without the use of UV radiation, 63% and 65.7% of MIB and GSM, respectively, were removed. Higher efficiency of the treatment was observed with a higher O₃ concentration which allows a shorter reaction time.

Understanding Pore Surface Modification of Sucrose-Modified Iron Oxide/Silica Mesoporous Composite for Degradation of Methylene Blue

Santa Barbara Amorphous (SBA-15) containing iron oxide with a sucrose-modified in a heterogeneous reaction for degradation methylene blue (MB) successful synthesized used hydrothermal, ultrasonication, and wet impregnation method. SBA-15 is mesoporous silica that can easily serve as external and internal surfaces making it suitable for a wide range of applications. The structure and morphology of materials were characterized using Surface Area Analyzer (SAA), X-ray diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), Scanning Electron Microscope-Energy Dispersive X-Ray (SEM-EDX), and Transmission Electron Microscopy (TEM). Iron oxide impregnated as a maghemite phase has an average size of 12 nm and well distributed on the SBA-15. After modified with sucrose the materials remaining stable, which has a two-dimensional hexagonal (p6mm) structure, high specific surface area, and large pore volume (up to 1.82 cm3.g−1). The degradation of MB was evaluated under visible light irradiation using UV-Vis spectroscopy. Catalytic activity showed efficiencies of 52.9; 70.2; and 21.1% for SBA-15, Fe2O3/SBA-15, and sucrose-modified Fe2O3/SBA-15 respectively. Sucrose-modified Fe2O3/SBA-15 has the lowest efficiency, which probably occurs due to the presence of pore-blocking and the formation of micropores on the external pore. The modification with sucrose has the advantage of producing a high surface area even though there is a catalytic center due to partial decomposition which causes a decrease in the efficiency of degradation of MB. All materials provide a high micro surface area so that they can be further adapted and can be widely applied to many potential applications as both catalyst support and an adsorbent. Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 

The formation, analysis, and control of chlor(am)ination-derived odor problems: A review

Odors and tastes have become universal problems related to drinking water quality. In addition to the typical odor problems caused by algae or microorganisms, the occurrence of odors derived from drinking water disinfection have attracted attention. The chlor(am)ination-derived odor substances have certain toxicity and odor-causing characteristics, and would enter the tap water through water distribution systems, directly affecting drinking water safety and customer experience. This study provided a comprehensive overview of the occurrence, detection, and control of odor substances derived from drinking water chlor(am)ination disinfection. The occurrence and formation mechanisms of several typical types of disinfection derived odor substances were summarized, including haloanisoles, N-chloroaldimines, iodotrihalomethanes, and halophenoles. They are mainly derived from specific precursors such as halophenols, anisoles, and amino acids species during the disinfection or distribution networks. In addition, the change of disinfectant during chlor(am)ination was also one of the causes of disinfection odors. Due to the extremely low odor threshold concentrations (OTCs) of these odor substances, the effective sample pre-enrichment for instrument identification and quantification are essential. The control strategies of odor problems mainly include adsorption, chemical oxidation, and combined processes such as ozonation and biological activated carbon processes (O₃/BAC) and ultraviolet-based advanced oxidation processes (UV-AOPs). Finally, the challenges and possible future research directions in this research field were discussed and proposed.

Comparative evaluation of 2-isopropyl-3-methoxypyrazine, 2-isobutyl-3-methoxypyrazine, and 2,4,6-trichloroanisole degradation by ultraviolet/chlorine and ultraviolet/hydrogen peroxide processes

2-Isopropyl-3-methoxypyrazine (IPMP), 2-Isobutyl-3-methoxypyrazine (IBMP), and 2,4,6-Trichloroanisole (TCA) are the primary emerging taste and odor (T&O) compounds in water systems with low thresholds (ng L^-1). The selected T&O compounds are known to be difficult to remove using conventional water treatment processes. In this study, we compared the removal characteristics of the three T&O compounds using UV/Cl₂ and UV/H₂O₂. The removal rates of the three compounds by direct photolysis at 254 nm were less than 10%, even at a high UV dose (approximately 1000 mJ cm^-2). Under conditions of an oxidant injection volume of 5 mg L^-1 and UV dose of 1000 mJ cm^-2, the degradation rate of the target compounds in the UV/H₂O₂ process exceeded that of the UV/Cl₂ process. Moreover, the results revealed that pH has a significant impact on the removal of the T&O compounds during the UV/Cl₂ process. The IPMP, IBMP, and TCA were found to be more reactive with hydroxyl radicals than reactive chlorine species (RCS). A predictive tool was developed to determine the optimal operating condition using the generalized reduced gradient (GRG) nonlinear solver. In the UV/H₂O₂ process, the EED value for 90% removing rate was 0.156 kWh m^-3 for the IPMP, 0.135 kWh m^-3 for the IBMP, and 0.154 kWh m^-3 for the TCA, respectively. In case of the UV/Cl₂, the EED value for 50% removing rate was 0.174 kWh m^-3 for the IPMP, 0.138 kWh m^-3 for the IBMP, and 0.169 kWh m^-3 for the TCA, respectively.

Simultaneous mitigation of disinfection by-product formation and odor compounds by peroxide/Fe(II)-based process: Combination of oxidation and coagulation

To remove disinfection by-product (DBP) precursors and mitigate odor compounds, peroxide (peroxymonosulfate and persulfate)/Fe(II)-based process was applied as a combination of coagulation and oxidation. Compared with traditional Fe-based salt coagulation (FeSO₄ and FeCl₃), peroxide/Fe(II)-based process was more efficient in dissolved organic carbon, UV₂₅₄ and turbidity removal, and peroxymonosulfate showed better performance than persulfate. The better coagulation performance arose from a combination of enhanced neutralization and different characteristics of flocs. Even though the combined process would increase the bromine substitution factor of DBPs, DBP formation and DBP-associated toxicity after peroxide/Fe(II)-based process were 9.2-38.8% and 5.2-27.2% lower than that after conventional Fe(III) coagulation. Both enhanced dissolved organic matter removal and oxidation of DBP precursors played vital roles in DBP control. Conventional Fe-based salt coagulation could hardly remove odor compounds (less than 10%, generally), whereas 28.2-84.9% of odor compounds were degraded during peroxide/Fe(II)-based process, due to free radical formation. This study demonstrated that PMS/Fe(II)-based process might be a promising treatment process for simultaneous DBP control and odor removal in source water.

Boosted sono-oxidative catalytic degradation of Brilliant green dye by magnetic MgFe2O4 catalyst: Degradation mechanism, assessment of bio-toxicity and cost analysis

The magnetic MgFe₂O₄ nanoparticles (NPs) were fabricated via a facile co-precipitation technique and was comprehensively characterized by XRD, FTIR, SEM, EDX and VSM. The prepared NPs were used as catalyst in presence of ultrasound (US) irradiation to activate persulfate (PS) for generation of sulfate radicals (SO₄^·-) for boosted degradation of toxic Brilliant Green (BG) dye. Preliminary experiments revealed that highest BG dye degradation efficiency of 91.63% was achieved at MgFe₂O₄ catalyst dose of 1.0 g/L, PS dose of 300 mg/L, and initial dye concentration of 70 ppm within 15 min of US irradiation. However, only US, US in presence of PS oxidation and US in presence of MgFe₂O₄ catalyst have shown 20.2%, 83.6% and 45.0% of BG dye removal, respectively. Furthermore, response surface methodology (RSM) based central composite design (CCD) was executed to investigate the effect of interaction between independent variables such as MgFe₂O₄ catalyst dose (0.5-1.5 g/L), PS dose (150-350 mg/L), initial BG dye concentration (50-150 ppm) and US irradiation time (4-12 min). The RSM based quadratic model was used to predict the experimental data, and the prediction accuracy was confirmed by analysis of variance (R² = 0.98). The established RSM model has predicted the optimum experimental conditions as MgFe₂O₄ catalyst dose of 0.75 g/L, PS dose of 300 mg/L, initial dye concentration of 75 ppm and sonication time of 10 min. Subsequently, the treatment cost analysis was performed for all thirty experimental runs of CCD, and the RSM predicted response was found to be evidently optimum as this has delivered best economic condition (140 $/kg of BG removed) with respect to relative dye removal (%). COD removal and residual sulfate analysis have demonstrated satisfactory reduction of COD (90.31%) as well as sulfate ions (42.87 ppm) in the dye solution after treatment. Results of degradation pathway analysis portrayed the transformation of BG molecule (M/Z ratio 385) into simpler fractions with M/Z ratio of 193, 161, 73, and 61. Moreover, the toxicity analysis revealed that sono-catalytically activated PS system has efficiently reduced the toxicity level of BG dye from 93.9% to 5.13%.

H2S Removal from Groundwater by Chemical Free Advanced Oxidation Process Using UV-C/VUV Radiation

Sulfide species may be present in groundwater due to natural processes or due to anthropogenic activity. H₂S contamination poses odor nuisance and may also lead to adverse health effects. Advanced oxidation processes (AOPs) are considered promising treatments for hydrogen-sulfide removal from water, but conventional AOPs usually require continuous chemical dosing, as well as post-treatment, when solid catalysts are applied. Vacuum-UV (VUV) radiation can generate ·OH in situ via water photolysis, initiating chemical-free AOP. The present study investigated the applicability of VUV-based AOP for removal of H₂S both in synthetic solutions and in real groundwater, comparing combined UV-C/VUV and UV-C only radiation in a continuous-flow reactor. In deionized water, H₂S degradation was much faster under the combined radiation, dominated by indirect photolysis, and indicated the formation of sulfite intermediates that convert to sulfate at high radiation doses. Sulfide was efficiently removed from natural groundwater by the two examined lamps, with no clear preference between them. However, in anoxic conditions, common in sulfide-containing groundwater, a small advantage for the combined lamp was observed. These results demonstrate the potential of utilizing VUV-based AOP for treating H₂S contamination in groundwater as a chemical-free treatment, which can be especially attractive to remote small treatment facilities.

Mesoporous LaFeO3: Synergistic Effect of Adsorption and Visible Light Photo-Fenton Processes for Phenol Removal from Refinery Wastewater

Mesoporous LaFeO3 as a visible light-driven photocatalyst was prepared by a nanocasting method using mesoporous silica (SBA-15) as a hard template. The as-prepared LaFeO3 photocatalyst was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), N2 adsorption-desorption, X-ray photoelectron spectroscopy (XPS), and optical absorption spectra. The characterization studies and experimental results showed that LaFeO3 with porous structure caused by the removal of SBA-15 hard template could enhance the specific surface area of the resulting photocatalyst, which improves the phenol adsorption ability of the photocatalyst and in turn enhances its photo-Fenton catalytic activity. The photo-Fenton catalytic activity of the photocatalyst was investigated by photo-Fenton degradation of aqueous phenol under visible light irradiation. The effects of catalyst dosage, H2O2 concentration, and solution pH on the photo-Fenton catalytic degradation of phenol using mesoporous LaFeO3 were studied and optimized. Under the optimal conditions of 20 mg L−1 phenol, 1.0 g L−1 catalyst, and 10 mM H2O2 at pH = 5, the photo-Fenton degradation of phenol (93.47%) was achieved in 180 min under visible light irradiation. Furthermore, our results proved the stability and reusability of mesoporous LaFeO3 and revealed its catalytic mechanism for the photo-Fenton degradation of phenol.