A review on emerging contaminants in wastewaters and the environment: current knowledge, understudied areas and recommendations for future monitoring

Occurrence and risks of pharmaceuticals, personal care products, and endocrine-disrupting compounds in Chinese surface waters

The continuous and rapid increase of chemical pollution in surface waters has become a pressing and widely recognized global concern. As emerging contaminants (ECs) in surface waters, pharmaceutical and personal care products (PPCPs), and endocrine-disrupting compounds (EDCs) have attracted considerable attention due to their wide occurrence and potential threat to human health. Therefore, a comprehensive understanding of the occurrence and risks of ECs in Chinese surface waters is urgently required. This study summarizes and assesses the environmental occurrence concentrations and ecological risks of 42 pharmaceuticals, 15 personal care products (PCPs), and 20 EDCs frequently detected in Chinese surface waters. The ECs were primarily detected in China's densely populated and highly industrialized regions. Most detected PPCPs and EDCs had concentrations between ng/L to µg/L, whereas norfloxacin, caffeine, and erythromycin had relatively high contamination levels, even exceeding 2000 ng/L. Risk evaluation based on the risk quotient method revealed that 34 PPCPs and EDCs in Chinese surface waters did not pose a significant risk, whereas 4-nonylphenol, 4-tert-octylphenol, 17α-ethinyl estradiol, 17β-estradiol, and triclocarban did. This review provides a comprehensive summary of the occurrence and associated hazards of typical PPCPs and EDCs in Chinese surface waters over the past decade, and will aid in the regulation and control of these ECs in Chinese surface waters.

Socio-environmental externalities of sewage waste management

Conventional sewage management is expensive and inefficient, putting the environment and public health at risk, making access to sewage services difficult for everyone. Reusing sewage waste has agricultural and economic potential, but can contain harmful contaminants if not treated properly. This review is based on the hypothesis that the destination of sewage waste generates environmental and social externalities, which have not yet been widely compared. With the aim of identifying, from the literature, the socio-environmental externalities generated by different sewage waste management approaches, a systematic review of the literature was carried out, including 244 documents, with 50 % of these discussing impacts of conventional treatment and 37 % analyzing the reuse of waste. The main impacts and externalities were evaluated in three situations: untreated sewage, treated sewage, and reused waste. The results indicate that sewage waste has an underutilized economic value and can generate revenue, reduce operational costs and electricity expenses. Six negative externalities generated by conventional sewage treatment were identified: health costs; environmental cleaning; carbon offsetting; damage to tourism; damage to fishing and agriculture; and real estate depreciation. In reuse, there is a risk of two negative externalities: health costs and environmental cleaning, but two positive externalities were also identified: the reduction of phosphate rock mining and the neutralization of carbon credits. The complexity of the transition to sustainable sewage treatment practices is highlighted given the lack of consensus on the safe use of sewage waste, the lack of regulatory standardization, implementation costs and differences in regional parameters, highlighting the need for preliminary experimentation in a multidisciplinary and contextualized approach, considering comparative externalities among the available sewage waste management possibilities.

Ecotoxicological assessment of UV filters benzophenone-3 and TiO2 nanoparticles, isolated and in a mixture, in developing zebrafish (Danio rerio)

The increasing use of UV filters, such as benzophenone-3 (BP-3) and titanium dioxide nanoparticles (TiO2 NPs), has raised concerns regarding their ecotoxicological effects on the aquatic environment. The aim of the present study was to examine the embryo-larval toxicity attributed to BP-3 or TiO2 NPs, either alone or in a mixture, utilizing zebrafish (Danio rerio) as a model after exposure to environmentally relevant concentrations of these compounds. Zebrafish embryos were exposed to BP-3 (10, 100, or 1000 ng/L) or TiO2 NPs (1000 ng/L) alone or in a mixture (BP-3 10, 100, or 1000 ng/L plus 1000 ng/L of TiO2 NPs) under static conditions for 144 hr. After exposure, BP-3 levels were determined by high-performance liquid chromatography (HPLC). BP-3 levels increased in the presence of TiO2 NPs, indicating that the BP-3 degradation decreased in the presence of the NPs. In addition, in the presence of zebrafish, BP-3 levels in water decreased, indicating that zebrafish embryos and larvae might absorb BP-3. Data demonstrated that, in general, environmentally relevant concentrations of BP-3 and TiO2 NPs, either alone or in a mixture, did not significantly induce changes in heart and spontaneous contractions frequencies, levels of reactive oxygen species (ROS), morphological and morphometric parameters as well as mortality rates during 144 hr exposure. However, the groups exposed to TiO2 NPs alone and in a mixture with BP-3 at 10 ng/L exhibited an earlier significant hatching rate than the controls. Altogether, the data indicates that a potential ecotoxicological impact on the aquatic environment exists.

The influence of temperature on the impacts of caffeine in mussels: Evaluating subcellular impacts and model predictions

In aquatic ecosystems, the presence of pharmaceuticals, particularly caffeine (CAF), has been linked to wastewater discharge, hospital waste, and the disposal of expired pharmaceutical products containing CAF. Additionally, rising temperatures due to climate change are anticipated in aquatic environments. This study aimed to assess the toxicity of various CAF concentrations under current (17 °C) and projected (21 °C) temperature conditions, using the mussel Mytilus galloprovincialis as a bioindicator species. Subcellular impacts were evaluated following 28 days of exposure to four CAF concentrations (0.5; 1.0; 5.0; 10.0 μg/L) at the control temperature (17 °C). Only effects at an environmentally relevant CAF concentration (5.0 μg/L) were assessed at the highest temperature (21 °C). The overall biochemical response of mussels was evaluated using non-metric Multidimensional Scaling (MDS) and the Integrated Biomarker Response (IBR) index, while the Independent Action (IA) model was used to compare observed and predicted responses. Results showed that at 17 °C, increased CAF concentrations were associated with higher metabolism and biotransformation capacity, accompanied by cellular damage at the highest concentration. Conversely, under warming conditions (21 °C), the induction of antioxidant enzymes was observed, although insufficient to prevent cellular damage compared to the control temperature. Regarding neurotoxicity, at 17 °C, the activity of the acetylcholinesterase enzyme was inhibited up to 5.0 μg/L; however, at 10.0 μg/L, activity increased, possibly due to CAF competition for adenosine receptors. The IA model identified a synergistic response for most parameters when CAF and warming acted together, aligning with observed results, albeit with slightly lower magnitudes.

Season and side-chain length affect the occurrences and behaviors of phthalic acid esters in wastewater treatment plants

Emerging pollutants (EPs) are prevalent in aquatic environments globally. Researchers strive to understand their occurrence and behavior prior to their release into the environment. In this study, we examined five wastewater treatment plants (WWTPs), collected 50 wastewater samples and 10 sludge samples. We explored the sources and destinations of phthalic acid esters (PAEs) within these WWTPs using mass balance equations. Wastewater treatment diminished the frequency and concentration of PAEs, and decreased the fraction of short-chain PAEs. We confirmed the increased concentration of PAEs post-primary treatment and modified the mass balance equation. Calculations suggest that weaker "the mix" in winter than in summer and stronger sedimentation in winter than in summer resulted in high efficiency of PAEs removal by winter wastewater treatment. The mass flux of biodegradation was influenced by the combination of biodegradation efficiency and the strength of the particular type of PAEs collected, with no seasonal differences. Mass fluxes for sludge sedimentation were mainly influenced by season and were higher in winter than in summer. This study enhances our understanding of emerging pollutants in manual treatment facilities and offers insights for optimizing wastewater treatment methods for water professionals.

"PAW" a smart analytical process assessing lipophilicity of solutes in mixtures

BACKGROUND

The analysis of mixtures of contaminants remains a challenging task in many fields, including water quality and waste management. For example, the degradation of industrial waste such as plastics, leads to complex mixtures with hundreds of organic contaminants and often non-referenced analytes. In such cases, non-targeted or effects-based analyses provide complementary information to classical targeted-analyses, regarding contaminants nature or properties (molecular mass, lability, toxicity). In this study, a novel analytical method is proposed to characterise mixtures of unknown organic contaminants, with a focus on the lipophilicity of solutes.

RESULTS

The proposed process, named "PAW" (Partition of Aqueous Waste), aims at the quantification of octanol-water partition coefficients (POW) of mixed organic analytes. The process is based on sequential liquid-liquid partition equilibria. The output result is a lipophilicity histogram of the solutes, screened according to the chosen detection method. The process quantifies the distribution of analytes as a function of their octanol-water partition coefficients, without requiring any identification or prior knowledge. The PAW process is applicable with various detectors (UV-Visible, total carbon, liquid scintillation, etc.) allowing to focus on specific families of contaminants (e.g. organic solutes, colloids, 14C-bearing, etc.). Experimental proofs of concept are proposed, illustrating process implementation and possible fields of application. The first example deals with purity analysis of synthetic radiolabeled compounds. The second example aims the monitoring of cellulose degradation and quantification of the lipophilicity of degradation products.

SIGNIFICANCE

The PAW analytical process seems especially useful for characterisation of mixtures containing both hydrophilic and lipophilic compounds, e.g. neutral and ionizable organic contaminants, hardly characterisable simultaneously by chromatographic methods. It could be complementary to more detailed targeted or screening analysis of samples and effluents. For example it may help assessing the composition and environmental fate of mixtures of unknown analytes, thus facilitating waste management or mitigation strategies.

Limitations of wastewater treatment plants in removing trace anthropogenic biomarkers and future directions: A review

This review highlights the limitations faced by conventional wastewater treatment plants (WWTPs) in effectively removing contaminants of emerging concern (CECs), heavy metals (HMs), and Escherichia coli (E. coli). This emphasises the limitations of current treatment methods and advocates for innovative approaches to enhance the removal efficiency. By following the PRISMA guidelines, the study systematically reviewed relevant literature on detecting and remedying these pollutants in wastewater treatment facilities. Conventional wastewater treatment plants struggle to eliminate CECs, HMs, and E. coli owing to their small size, persistence, and complex nature. The review suggests upgrading WWTPs with advanced tertiary processes to significantly improve contaminant removal. This calls for cost-effective treatment parameters and standardised assessment techniques to enhance the fate of MPs in WWTPs and WRRFs. It recommends integrating insights from mass-balance model studies on MPs in WWTP to overcome modelling challenges and ensure model reliability. In conclusion, this review underscores the urgent need for advancements in wastewater treatment processes to mitigate the environmental impact of trace anthropogenic biomarkers. Future efforts should focus on conducting comprehensive studies, implementing advanced treatment methods, and optimising management practices in WWTPs and WRRFs.

Mechanistic insights into sulfadimethoxine degradation via microbially driven Fenton reactions

Biodegradation, while cost-effective, is hindered by the requirement for specialized microorganisms and co-contaminants. Innovative biological technologies like the microbially driven Fenton reaction, hold promise for enhancing degradation efficiency. However, the intricate biochemical processes and essential steps for effective degradation in such systems have remained unclear. In this study, we harnessed the potential of the microbially driven Fenton reaction by employing Shewanella oneidensis MR-1 (MR-1). Our approach showcased remarkable efficacy in degrading a range of contaminants, including sulfadimethoxine (SDM), 4,4'-dibromodiphenyl ether (BDE-15) and atrazine (ATZ). Using SDM as a model contaminant of emergent contaminants (ECs), we unveiled that biodegradation relied on the generation of hydroxyl radicals (•OH) and involvement of oxidoreductases. Transcriptomic analysis shed light on the pivotal components of extracellular electron transfer (EET) during both anaerobic and aerobic periods. The presence of reactive oxidizing species induced cellular damage and impeded DNA repair, thereby affecting the Mtr pathway of EET. Moreover, the formation of vivianite hindered SDM degradation, underscoring the necessity of maintaining iron ions in the solution to ensure sustainable and efficient degradation. Overall, this study offers valuable insights into microbial technique for ECs degradation, providing a comprehensive understanding of degradation mechanisms during aerobic/anaerobic cycling.

Accumulation of antibiotics in the environment: Have appropriate measures been taken to protect Canadian human and ecological health?

In Canada, every day, contaminants of emerging concern (CEC) are discharged from waste treatment facilities into freshwaters. CECs such as pharmaceutical active compounds (PhACs), personal care products (PCPs), per- and polyfluoroalkyl substances (PFAS), and microplastics are legally discharged from sewage treatment plants (STPs), water reclamation plants (WRPs), hospital wastewater treatment plants (HWWTPs), or other forms of wastewater treatment facilities (WWTFs). In 2006, the Government of Canada established the Chemicals Management Plan (CMP) to classify chemicals based on a risk-priority assessment, which ranked many CECs such as PhACs as being of low urgency, therefore permitting these substances to continue being released into the environment at unmonitored rates. The problem with ranking PhACs as a low priority is that CMP's risk management assessment overlooks the long-term environmental and synergistic effects of PhAC accumulation, such as the long-term risk of antibiotic CEC accumulation in the spread of antibiotic resistance genes. The goal of this review is to specifically investigate antibiotic CEC accumulation and associated environmental risks to human and environmental health, as well as to determine whether appropriate legislative strategies are in place within Canada's governance framework. In this research, secondary data on antibiotic CEC levels in Canadian and international wastewaters, their potential to promote antibiotic-resistant residues, associated environmental short- and long-term risks, and synergistic effects were all considered. Unlike similar past reviews, this review employed an interdisciplinary approach to propose new strategies from the perspectives of science, engineering, and law.

Rare biosphere drives deterministic community assembly, co-occurrence network stability, and system performance in industrial wastewater treatment system

Bacterial community is strongly associated with activated sludge performance, but there still remains a knowledge gap regarding the rare bacterial community assembly and their influence on the system performance in industrial wastewater treatment plants (IWWTPs). Here, we investigated bacterial communities in 11 full-scale IWWTPs with similar process designs, aiming to uncover ecological processes and functional traits regulating abundant and rare communities. Our findings indicated that abundant bacterial community assembly was governed by stochastic processes; thereby, abundant taxa are generally present in wastewater treatment compartments across different industrial types. On the contrary, rare bacterial taxa were primarily driven by deterministic processes (homogeneous selection 61.9%-79.7%), thus they only exited in specific IWWTPs compartments and wastewater types. The co-occurrence networks analysis showed that the majority of keystone taxa were rare bacterial taxa, with rare taxa contributing more to network stability. Furthermore, rare bacteria rather than abundant bacteria in the oxic compartment contributed more to the degradation of xenobiotics compounds, and they were main potential drivers of pollutant removal. This study demonstrated the irreplaceable roles of rare bacterial taxa in maintaining system performance of IWWTPs, and called for environmental engineers and microbial ecologists to increase their attention on rare biosphere.

Combining Nontargeted Analysis with Computer-Based Hazard Comparison Approaches to Support Prioritization of Unregulated Organic Contaminants in Biosolids

Biosolids are a byproduct of wastewater treatment that can be beneficially applied to agricultural land as a fertilizer. While U.S. regulations limit metals and pathogens in biosolids intended for land applications, no organic contaminants are currently regulated. Novel techniques can aid in detection, evaluation, and prioritization of biosolid-associated organic contaminants (BOCs). For example, nontargeted analysis (NTA) can detect a broad range of chemicals, producing data sets representing thousands of measured analytes that can be combined with computational toxicological tools to support human and ecological hazard assessment and prioritization. We combined NTA with a computer-based tool from the U.S. EPA, the Cheminformatics Hazard Comparison Module (HCM), to identify and prioritize BOCs present in U.S. and Canadian biosolids (n = 16). Four-hundred fifty-one features were detected in at least 80% of samples, with identities of 92 compounds confirmed or assigned probable structures. These compounds were primarily categorized as endogenous compounds, pharmaceuticals, industrial chemicals, and fragrances. Examples of top prioritized compounds were p-cresol and chlorophene, based on human health end points, and fludioxonil and triclocarban, based on ecological health end points. Combining NTA results with hazard comparison data allowed us to prioritize compounds to be included in future studies of the environmental fate and transport of BOCs.

Temporal Analysis of Pharmaceuticals as Emerging Contaminants in Surface Water and Wastewater Samples: A Case Study

Pharmaceuticals in the environment are a global concern, with studies in all continents highlighting their widespread occurrence and potential ecological impacts, revealing their presence, fate, and associated risks in aquatic ecosystems. Despite typically occurring at low concentrations (ranging from ng/L to µg/L), advancements in analytical methods and more sensitive equipment have enabled the detection of a higher number of pharmaceuticals. In this study, surface and wastewater samples were extracted using solid phase extraction and analyzed using ultra-high-performance liquid chromatography with tandem mass spectrometry. Among the therapeutic classes investigated, nonsteroidal anti-inflammatory drugs/analgesics, antibiotics, and psychiatric drugs showed a higher number of detected pharmaceuticals. Concentrations ranged from below method detection limit ( Collapse

Key Words

• liquid chromatography
• mass spectrometry
• overtime analysis
• pharmaceuticals
• public health
• surface and wastewater samples

Collapse

MESH Headings Collapse

Grants

• UIDB/50006/2020 Fundação para a Ciência e Tecnologia
• UIDP/50006/2020 Fundação para a Ciência e Tecnologia
• LA/P/0008/2020 Fundação para a Ciência e Tecnologia
• PTDC/QUI-QAN/3899/2021 Fundação para a Ciência e Tecnologia
• PTDC/EAM-AMB/2023/2021 Fundação para a Ciência e Tecnologia
• MTS/SAS/0077/2020 Fundação para a Ciência e Tecnologia
• P223RT0141/ENOTTA-CA21147 Ibero-American Program on Science and Technology (CYTED) & European Cooperation in Science and Technology (COST)
• 101003777 Fundação para a Ciência e a Tecnologia (FCT) BiodivRestore Joint Call 2020-2021 - European Union's Horizon 2020 research and innovation programme

Collapse

Affiliation(s)

Paula Paíga REQUIMTE/LAQV, Instituto Superior de Engenharia do Porto, Instituto Politécnico do Porto, Rua Dr. António Bernardino de Almeida, 431, 4249-015 Porto, Portugal; (L.C.-S.); (M.C.); (S.F.)
Luísa Correia-Sá REQUIMTE/LAQV, Instituto Superior de Engenharia do Porto, Instituto Politécnico do Porto, Rua Dr. António Bernardino de Almeida, 431, 4249-015 Porto, Portugal; (L.C.-S.); (M.C.); (S.F.)
Manuela Correia REQUIMTE/LAQV, Instituto Superior de Engenharia do Porto, Instituto Politécnico do Porto, Rua Dr. António Bernardino de Almeida, 431, 4249-015 Porto, Portugal; (L.C.-S.); (M.C.); (S.F.)
Sónia Figueiredo REQUIMTE/LAQV, Instituto Superior de Engenharia do Porto, Instituto Politécnico do Porto, Rua Dr. António Bernardino de Almeida, 431, 4249-015 Porto, Portugal; (L.C.-S.); (M.C.); (S.F.)
Joana Vieira Águas do Centro Litoral, SA, Grupo Águas de Portugal, ETA da Boavista, Avenida Dr. Luís Albuquerque, 3030-410 Coimbra, Portugal; (J.V.)
Sandra Jorge Águas do Centro Litoral, SA, Grupo Águas de Portugal, ETA da Boavista, Avenida Dr. Luís Albuquerque, 3030-410 Coimbra, Portugal; (J.V.)
Jaime Gabriel Silva Águas do Douro e Paiva, SA, Grupo Águas de Portugal, Rua de Vilar, 235 5°, 4050-626 Porto, Portugal; Departamento de Engenharia Civil, Instituto Superior de Engenharia do Porto, Instituto Politécnico do Porto, Rua Dr. António Bernardino de Almeida, 431, 4249-015 Porto, Portugal
Cristina Delerue-Matos REQUIMTE/LAQV, Instituto Superior de Engenharia do Porto, Instituto Politécnico do Porto, Rua Dr. António Bernardino de Almeida, 431, 4249-015 Porto, Portugal; (L.C.-S.); (M.C.); (S.F.)

Collapse

Passive sampler housing and sorbent type determine aquatic micropollutant adsorption and subsequent bioassay responses

The combination of integrative passive sampling and bioassays is a promising approach for monitoring the toxicity of polar organic contaminants in aquatic environments. However, the design of integrative passive samplers can affect the accumulation of compounds and therewith the bioassay responses. The present study aimed to determine the effects of sampler housing and sorbent type on the number of chemical features accumulated in polar passive samplers and the subsequent bioassay responses to extracts of these samplers. To this end, four integrative passive sampler configurations, resulting from the combination of polar organic chemical integrative sampler (POCIS) and Speedisk housings with hydrophilic-lipophilic balance and hydrophilic divinylbenzene sorbents, were simultaneously exposed at reference and contaminated surface water locations. The passive sampler extracts were subjected to chemical non-target screening and a battery of five bioassays. Extracts from POCIS contained a higher number of chemical features and caused higher bioassay responses in 91% of cases, while the two sorbents accumulated similar numbers of features and caused equally frequent but different bioassay responses. Hence, the passive sampler design critically affected the number of accumulated polar organic contaminants as well as their toxicity, highlighting the importance of passive sampler design for effect-based water quality assessment.

Reviewing the use of zebrafish for the detection of neurotoxicity induced by chemical mixtures through the analysis of behaviour

The knowledge and assessment of mixtures of chemical pollutants in the aquatic environment is a complex issue that is often challenging to address. In this review, we focused on the use of zebrafish (Danio rerio), a vertebrate widely used in biomedical research, as a model for detecting the effects of chemical mixtures with a focus on behaviour. Our aim was to summarize the current status of the ecotoxicological research in this sector. Specifically, we limited our research to the period between January 2012 and September 2023, including only those works aimed at detecting neurotoxicity through behavioural endpoints, utilizing zebrafish at one or more developmental stages, from egg to adult. Additionally, we gathered the findings for every group of chemicals involved and summarised data from all the works we included. At the end of the screening process 101 papers were considered eligible for inclusion. Results show a growing interest in zebrafish at all life stages for this kind of research in the last decade. Also, a wide variety of different assays, involving different senses, was used in the works we surveyed, with exposures ranging from acute to chronic. In conclusion, the results of this study show the versatility of zebrafish as a model for the detection of mixture toxicity although, for what concerns behavioural analysis, the lack of standardisation of methods and endpoints might still be limiting.

A MXene Hydrogel-Based Versatile Microrobot for Controllable Water Pollution Management

The urgent demand for addressing dye contaminants in water necessitates the development of microrobots that exhibit remote navigation, rapid removal, and molecular identification capabilities. The progress of microrobot development is currently hindered by the scarcity of multifunctional materials. In this study, a plasmonic MXene hydrogel (PM-Gel) is synthesized by combining bimetallic nanocubes and Ti3C2Tx MXene through the rapid gelation of degradable alginate. The hydrogel can efficiently adsorb over 60% of dye contaminants within 2 min, ultimately achieving a removal rate of >90%. Meanwhile, the hydrogel exhibits excellent sensitivity in surface enhanced Raman scattering (SERS) detection, with a limit of detection (LOD) as low as 3.76 am. The properties of the plasmonic hydrogel can be further adjusted for various applications. As a proof-of-concept experiment, thermosensitive polymers and superparamagnetic particles are successfully integrated into this hydrogel to construct a versatile, light-responsive microrobot for dye contaminants. With magnetic and optical actuation, the robot can remotely sample, identify, and remove pollutants in maze-like channels. Moreover, light-driven hydrophilic-hydrophobic switch of the microrobots through photothermal effect can further enhance the adsorption capacity and reduced the dye residue by up to 58%. These findings indicate of a broad application potential in complex real-world environments.

Analysis of the remediation competence of Aspergillus flavus biomass in wastewater of the dyeing industry: An in-vitro study

The dyeing industry effluent causes severe environmental pollution and threatens the native flora and fauna. The current study aimed to analyze the physicochemical parameters of dyeing industry wastewater collected in different sites (K1, E2, S3, T4, and V5), as well as the metal tolerance and decolourisation ability of Aspergillus flavus. Furthermore, the optimal biomass quantity and temperatures required for efficient bioremediation were investigated. Approximately five dyeing industry wastewater samples (K1, E2, S3, T4, and V5) were collected from various sampling stations, and the majority of the physical and chemical characteristics were discovered to be above the permissible limits. A. flavus demonstrated outstanding metal resistance to As, Cu, Cr, Zn, Hg, Pb, Ni, and Cd on Potato Dextrose Agar (PDA) plates at concentrations of up to 500 g mL-1. At 4 g L-1 concentrations, A. flavus biomass decolorized up to 11.2-46.5%. Furthermore, 35°C was found to be the optimal temperature for efficient decolourisation of A. flavus biomass. The toxicity of 35°C-treated wastewater on V. mungo and prawn larvae was significantly reduced. These findings indicate that the biomass of A. flavus can be used to decolorize dyeing industry wastewater.

Predicting the new psychoactive substance activity of antitussives and evaluating their ecotoxicity to fish

The misuse of antitussives preparations is a continuing problem in the world, and imply that they might have potential new psychoactive substances (NPS) activity. However, few study focus on their ecological toxicity towards fish. In the present study, the machine learning (ML) methods gcForest and random forest (RF) were employed to predict NPS activity in 30 antitussives. The potential toxic target, mode of action (MOA), acute toxicity and chronic toxicity to fish were further investigated. The results showed that both gcForest and RF achieved optimal performance when utilizing combined features of molecular fingerprint (MF) and molecular descriptor (MD), with area under the curve (AUC) = 0.99, accuracy >0.94 and f1 score > 0.94, and were applied to screen the NPS activity in antitussives. A total of 15 antitussives exhibited potential NPS activity, including frequently-used substances like codeine and dextromethorphan. The binding affinity of these antitussives with zebrafish dopamine transporter (zDAT) was high, and even surpassing that of some traditional narcotics and NPS. Some antitussives formed hydrogen bonds or salt bridges with aspartate (Asp) 95, tyrosine (Tyr) 171 of zDAT. For the ecotoxicity, the MOA of these 15 antitussives in fish was predicted as narcosis. The prenoxdiazin, pholcodine, codeine, dextromethorphan and dextrorphan exhibited very toxic/toxic to fish. It was necessary to pay close attention to the ecotoxicity of these antitussives. In this study, the integration of ML, molecular docking and ECOSAR approaches are powerful tools for understanding the toxicity profiles and ecological hazards posed by new pollutants.

Evaluation of acetanilide and antipyrine adsorption on lignin-derived activated carbons

In this study, the removal of two emerging pollutants (EPs), antipyrine and acetanilide, through adsorption on activated carbons (ACs) prepared by chemical activation of Organosolv lignin with H3PO4 were evaluated. ACs with different pore size distribution were obtained at different impregnation ratios (H3PO4/lignin, 0.5-3.0 w/w) and activating temperatures (500-900 °C). The porosity and surface chemistry of the ACs were determined, and a bimodal size distribution of micropores and narrow mesopores was observed for the different ACs. These ACs were tested for antipyrine and acetanilide adsorption in aqueous solutions in a batch system at 20 °C and low concentration levels (0.5-10 ppm). In general, the ACs exhibited higher adsorption affinity to acetanilide than to antipyrine due to its smaller molecular size. Langmuir adsorption isotherm was able to describe the adsorption equilibrium data. A new Linear Driving Force (2-LDF) kinetic model, based on the bimodal size distribution of micropores and narrow mesopores observed for the ACs has been developed. The new model provided a more accurate description of the batch adsorption rates than that obtained from conventional kinetic models, and also enabled to relate the pore size distribution of the adsorbent with the adsorption kinetics. The validity of this model was checked in small-scale column fixed bed adsorption for the AC showing the highest affinity for both EP. The kinetic model and equilibrium adsorption isotherm obtained from the batch experiments were successfully used to provide an accurate description of the bed service time and the full breakthrough profile of acetanilide and antipyrine.

Bacterial toxicity of Acetaminophen and Edaravone, and their binary mixtures: experimental and predicted values using traditional and novel Van Laar-based models

In recent years, the presence of Pharmaceutical Active Compounds (PhACs) in ecosystems has become a serious environmental problem due to their capacity to induce harmful effects at extremely low concentrations in both humans and wildlife. Water treatment plants have not been designed to remove these types of compounds efficiently. Thus, the detection of these pollutants is essential to evaluate their negative impacts and is one of the emerging issues in environmental chemistry. The main objective of this study is to determine the bacterial toxicity of two PhACs (both individually and as a mixture) through the quantification of bioluminescence inhibition in the marine bacteria Aliivibrio fischeri, a commonly used method in short-term toxicity tests. In this work, Acetaminophen and Edaravone, two drugs approved by the Food and Drug Administration, have been studied. The acute toxicity of these PhACs has been tested at two exposure times (5 and 15 min) and different concentrations, by estimation of the median effective concentration (EC50) for each individual compound or in combination at different concentrations. Moreover, the EC50 of the binary mixtures Acetaminophen/Edaravone have been forecast using two traditional predictive models, Concentration Addition and Independent Action. The results show that toxicity decreases with exposure time and depends on the concentration tested. Furthermore, a novel semi-empirical Van Laar-based model has been proposed and validated with the experimental data from this study and literature data, obtaining satisfactory estimations of the EC50 for binary mixtures.

Data-driven approaches linking wastewater and source estimation hazardous waste for environmental management

Industrial enterprises are major sources of contaminants, making their regulation vital for sustainable development. Tracking contaminant generation at the firm-level is challenging due to enterprise heterogeneity and the lack of a universal estimation method. This study addresses the issue by focusing on hazardous waste (HW), which is difficult to monitor automatically. We developed a data-driven methodology to predict HW generation using wastewater big data which is grounded in the availability of this data with widespread application of automatic sensors and the logical assumption that a correlation exists between wastewater and HW generation. We created a generic framework that used representative variables from diverse sectors, exploited a data-balance algorithm to address long-tail data distribution, and incorporated causal discovery to screen features and improve computation efficiency. Our method was tested on 1024 enterprises across 10 sectors in Jiangsu, China, demonstrating high fidelity (R² = 0.87) in predicting HW generation with 4,260,593 daily wastewater data.

Efficient Decaffeination with Recyclable Magnetic Microporous Carbon from Renewable Sources: Kinetics and Isotherm Analysis

Rapid global urbanization and population growth have ignited an alarming surge in emerging contaminants in water bodies, posing health risks, even at trace concentrations. To address this challenge, novel water treatment and reuse technologies are required as current treatment systems are associated with high costs and energy requirements. These drawbacks provide additional incentives for the application of cost-effective and sustainable biomass-derived activated carbon, which possesses high surface area and low toxicity. Herein, we synthesized microporous activated carbon (MAC) and its magnetic derivative (m-MAC) from tannic acid to decaffeinate contaminated aqueous solutions. Detailed characterization using SEM, BET, and PXRD revealed a very high surface area (>1800 m2/g) and a highly porous, amorphous, heterogeneous sponge-like structure. Physicochemical and thermal analyses using XPS, TGA, and EDS confirmed thermal stability, unique surface moieties, and homogeneous elemental distribution. High absorption performance (>96 %) and adsorption capacity (287 and 394 mg/g) were recorded for m-MAC and MAC, respectively. Mechanistic studies showed that the sorption of caffeine is in tandem with multilayer and chemisorptive mechanisms, considering the models' correlation and error coefficients. π-π stacking and hydrogen bonding were among the interactions that could facilitate MAC-Caffeine and m-MAC-Caffeine bonding interactions. Regeneration and reusability experiments revealed adsorption efficiency ranging from 90.5-98.4 % for MAC and 88.6-93.7 % for m-MAC for five cycles. Our findings suggest that MAC and its magnetic derivative are effective for caffeine removal, and potentially other organic contaminants with the possibility of developing commercially viable and cost-effective water polishing tools.

Chronic toxicity of sediment-bound triclosan on freshwater walking catfish Clarias magur: Organ level accumulation and selected enzyme biomarker responses

Triclosan (TCS) is a biocide widely used in personal care and medicinal products. TCS persists in sediments and has been detected worldwide, making sediments a vital route of TCS exposure to aquatic organisms. This experiment explored the bioaccumulation and toxicological effects of TCS-contaminated sediment. The study revealed that the half-life of TCS in the sediment-water system was 21.52 days. Exposure of Clarias magur juveniles to 0.4 and 0.8 mg kg-1 TCS-spiked sediment resulted in high Biota-Sediment Accumulation Factor (BSAF) with the highest bioaccumulation in the liver (29.62-73.61 mg kg-1), followed by gill (9.22-17.57 mg kg-1), kidney (5.04-9.76 mg kg-1), muscle (2.63-4.87 mg kg-1) and brain (1.53-3.20 mg kg-1). Furthermore, a concentration-dependent increase in oxidative stress biomarkers such as superoxide dismutase (SOD), catalase (CAT) and glutathione-S-transferase (GST) was documented during 45 days of exposure in gill, liver, kidney, muscle, and brain tissues of exposed fish. A similar increasing trend was also recorded for liver transaminase enzymes such as glutamic oxaloacetic transaminase (GOT) and glutamic pyruvic transaminase (GPT) during the experimental period compared to control. Serum biochemical analysis revealed a significant time and concentration-dependent increase in serum glucose, serum GOT, and serum GPT, while serum total protein and albumin decreased significantly during exposure. These findings demonstrate high bioaccumulative and toxic nature of TCS in fish, promoting multiple physiological and biochemical dysfunctions through sediment exposure. The study underscores the urgent need for strengthened regulations and robust monitoring of triclosan across various environmental matrices, including sediment, to mitigate the detrimental impacts of TCS effectively.

Heterostructure g-C3N4/Bi2MoO6 PVDF nanofiber composite membrane for the photodegradation of steroid hormone micropollutants

Photocatalytic membrane reactors (PMRs) are a promising technology for micropollutant removal. Sunlight utilization and catalyst surface sites limit photodegradation. A poly(vinylidene fluoride) (PVDF) nanofiber composite membrane (NCM) with immobilized visible-light-responsive g-C3N4/Bi2MoO6 (BMCN) were developed. Photodegradation of steroid hormones with the PVDF-BMCN NCM was investigated with varying catalyst properties, operating conditions, and relevant solution chemistry under solar irradiation. Increasing CN ratio (0-65 %) enhanced estradiol (E2) degradation from 20 ± 10 to 75 ± 7 % due to improved sunlight utilization and photon lifetime. PVDF nanofibers reduced self-aggregation of catalysts. Hydraulic residence time and light intensity enhanced the photodegradation. With the increasing pH value, the E2 removal decreased from 84 ± 4 to 67 ± 7 % owing to electrical repulsion and thus reduced adsorption between catalysts and E2. A removal of 96 % can be attained at environmentally relevant feed concentration (100 ng.L-1) with a flux of 60 L.m-2.h-1, irradiance of 100 mW.cm-2, and 1 mg.cm-2 BMCN65 loading. This confirmed that heterojunction photocatalysts can enhance micropollutants degradation in PMRs.

Anaerobic co-metabolic biodegradation of pharmaceuticals and personal care products driven by glycerol fermentation

Anaerobic digestion in two sequential phases, acidogenesis and methanogenesis, has been shown to be beneficial for enhancing the biomethane generation from wastewater. In this work, the application of glycerol (GOH) as a fermentation co-substrate during the wastewater treatment was evaluated on the biodegradation of different pharmaceuticals and personal care products (PPCPs). GOH co-digestion during acidogenesis led to a significant increase in the biodegradation of acetaminophen (from 78 to 89%), ciprofloxacin (from 25 to 46%), naproxen (from 73 to 86%), diclofenac (from 36 to 48%), ibuprofen (from 65 to 88%), metoprolol (from 45 to 59%), methylparaben (from 64 to 78%) and propylparaben (from 68 to 74%). The heterotrophic co-metabolism of PPCPs driven by glycerol was confirmed by the biodegradation kinetics, in which kbio (biodegradation kinetics constant) values increased from 0.18 to 2.11 to 0.27-3.60 L g-1-VSS d-1, for the operational phases without and with GOH, respectively. The assessment of metabolic pathways in each phase revealed that the prevalence of aromatic compounds degradation, metabolism of xenobiotics by cytochrome P450, and benzoate degradation routes during acidogenesis are key factors for the enzymatic mechanisms linked to the PPCPs co-metabolism. The phase separation of anaerobic digestion was effective in the PPCPs biodegradation, and the co-fermentation of glycerol provided an increase in the generation potential of biomethane in the system (energetic potential of 5.0 and 6.3 kJ g-1-CODremoved, without and with GOH, respectively). This study showed evidence that glycerol co-fermentation can exert a synergistic effect on the PPCPs removal during anaerobic digestion mediated by heterotrophic co-metabolism.

Iron-decorated covalent organic framework as efficient catalyst for activating peroxydisulfate to degrade 2,4-dichlorophenol: Performance and mechanism insight

Herein, a novel two-dimensional double-pore covalent organic framework (JLNU-305) was synthesized using N,N,N',N'-tetrakis(4-aminophenyl)-1,4-phenylenediamine (TAPD) and 2,2'-bipyridine-5,5'-dicarboxaldehyde (BPDA). The extended π-π conjugated structure and nitrogen-riched pyridine in JLNU-305 (JLNU = Jilin Normal University) provide abundant binding sites for Fe doping. The obtained JLNU-305-Fe exhibited high and recycled catalytic efficiency for peroxydisulfate (PDS) activation to completely degrade 10 mg/L 2,4-dichlorophenol (2,4-DCP) within 8 min. The JLNU-305-Fe/PDS system showed excellent catalytic activity and cyclic stability. The capture experiments and electron paramagnetic resonance (ESR) analysis indicated that the catalytic behavior of JLNU-305-Fe/PDS is contributed to the synergistic effect between free radicals and non-free radicals. It is the first time to activate PDS for covalent organic frameworks (COFs) being used to degrade 2,4-DCP, which has a great potential for development and practical application in related water environment remediation.

Occurrence of Pharmaceutical Micropollutants in Lake Nahuel Huapi, Argentine Patagonia

Tourism is one of the most important activities for the economy of Nor Patagonia Argentina. In Bariloche City, located on the shores of Lake Nahuel Huapi, both the permanent and the temporary populations have increased significantly in recent decades, and this has not necessarily been accompanied by an improvement in sewage networks. Emerging micropollutants such as pharmaceutical compounds reach aquatic systems directly, in the absence of a domestic sewage network, or through effluents from wastewater treatment plants (WWTP), which do not efficiently remove these substances and represent a major threat to the environment. Therefore, the objective of our study was to monitor the presence of pharmaceutical compounds discharged both through wastewater effluents and diffusely from housing developments into Lake Nahuel Huapi. The results obtained demonstrate the presence of pharmaceuticals in Lake Nahuel Huapi with concentrations ranging from not detectable (ND) to 110.6 ng L-1 (caffeine). The highest pharmaceutical concentration recorded in WWTP influent corresponded to caffeine (41728 ng L-1), and the lowest concentration was paracetamol (18.8 ng L-1). The removal efficiency of pharmaceuticals in the WWTP was calculated, and ranged from 0% for carbamazepine to 66% for ciprofloxacin. This antibiotic showed the lowest % of attenuation (73%) in Lake Nahuel Huapi. These results on the occurrence of a wide variety of pharmaceuticals are the first generated in Patagonia, representing a regional baseline for this type of micropollutant and valuable information for the subsequent design of removal strategies for emerging pharmaceutical pollutants in surface water. Environ Toxicol Chem 2024;43:1274-1284. © 2024 SETAC.

Developing an Approach for Integrating Chemical Analysis and Transcriptional Changes to Assess Contaminants in Water, Sediment, and Fish

Pharmaceuticals in aquatic environments pose threats to aquatic organisms because of their continuous release and potential accumulation. Monitoring methods for these contaminants are inadequate, with targeted analyses falling short in assessing water quality's impact on biota. The present study advocates for integrated strategies combining suspect and targeted chemical analyses with molecular biomarker approaches to better understand the risks posed by complex chemical mixtures to nontarget organisms. The research aimed to integrate chemical analysis and transcriptome changes in fathead minnows to prioritize contaminants, assess their effects, and apply this strategy in Wascana Creek, Canada. Analysis revealed higher pharmaceutical concentrations downstream of a wastewater-treatment plant, with clozapine being the most abundant in fathead minnows, showing notable bioavailability from water and sediment sources. Considering the importance of bioaccumulation factor and biota-sediment accumulation factor in risk assessment, these coefficients were calculated based on field data collected during spring, summer, and fall seasons in 2021. Bioaccumulation was classified as very bioaccumulative with values >5000 L kg-1, suggesting the ability of pharmaceuticals to accumulate in aquatic organisms. The study highlighted the intricate relationship between nutrient availability, water quality, and key pathways affected by pharmaceuticals, personal care products, and rubber components. Prioritization of these chemicals was done through suspect analysis, supported by identifying perturbed pathways (specifically signaling and cellular processes) using transcriptomic analysis in exposed fish. This strategy not only aids in environmental risk assessment but also serves as a practical model for other watersheds, streamlining risk-assessment processes to identify environmental hazards and work toward reducing risks from contaminants of emerging concern. Environ Toxicol Chem 2024;00:1-22. © 2024 SETAC.

A CuCo Bimetal Confined Hollow SiC Hybrid Photothermal Nanoreactor for the Integration of Pollutant Mineralization and Solar-Powered Water Evaporation

Growing attention has been paid to the rational treatment of antibiotics-bearing medical wastewater. However, the complexity of polluted wastewater makes the later comprehensive treatment difficult only by the Advanced Oxidation Process technique. Therefore, the coupled water treatment techniques including contaminant mineralization and regeneration of cleanwater become very attractive. A bimetallic functional hollow nanoreactor defined as (Co@SiO2/Cu-X) was successfully constructed by coating a Cu-doped silica layer on the metal-organic framework (ZIF-67) followed by programmed calcination in nitrogen. The nanoreactor was endowed with a hollow configuration composed of mesoporous N-doping C-Silica hybrid shell encapsulated ultrafine Cu and Co metallic species. Such a configuration allows for the efficient diffusion and open reaction space of big contaminant molecules. The catalytic synergy of exposed Co-Cu bimetals and the easy accessibility of electron-rich contaminants by polar N doping sites triggered surface affinity make the optimal Co@SiO2/Cu-6 afford an excellent catalytic norfloxacin mineralization activity (7 min, kabs=0.744 min-1) compared to Cu-free Co@SiO2-6 (kabs=0.493 min-1) and Co-6 (kabs=0.378 min-1) Benefiting from the above unique advantages, Co@SiO2/Cu-6 show excellent removal performance in degrading different pollutants (carbamazepine, oxytetracycline, tetracycline, and bisphenol A) and persistent recycled stability in removing NFX. In addition, by virtue of the excellent photothermal properties, interfacial solar water evaporation application by Co@SiO2/Cu-6 was further explored to reach the regeneration of cleanwater (1.595 kg m-2 h-1, 97.51 %). The integration of pollutant mineralization and solar water evaporation by creating the monolith evaporation by anchoring the Co@SiO2/Cu-6 onto the tailored melamine sponge allows the regeneration of cleanwater (1.6 kg⋅m-2⋅h-1) and synchronous pollutant removal (NFX, 95 %, 60 min), which provides potential possibility the treatment of complicated wastewater.

Fate of contaminants of emerging concern in two wastewater treatment plants after retrofitting tertiary treatment for reduction of nitrogen discharge

More and more previously designed wastewater treatment plants (WWTPs) are upgraded to tertiary treatment to meet the higher effluent discharge standards of conventional pollutants. Contaminants of emerging concern (CECs) can cause adverse effects on organisms and usually flow into WWTPs along with urban sewage. How the retrofitted WWTPs targeting conventional pollutants will influence the treatment efficiency of CECs is seldom discussed. This study investigates the removal of CECs in two full-scale newly retrofitted WWTPs (CD and JM WWTPs), containing high-efficiency sedimentation tank and denitrification deep bed filter for enhancing total nitrogen removal. The overall CEC removal efficiencies in the CD and JM WWTPs were 73.79 % and 93.63 %, respectively. Mass balance results indicated that CD WWTP and JM WWTP release a total of 36.89 and 88.58 g/d of CECs into the environment through effluent and excess sludge, respectively. Analysis of the concentration of CECs along the treatment process revealed most CECs were removed in the biological treatment units. The incorporation of newly constructed tertiary treatment proved beneficial for CEC removal and removed 2.93 % and 2.36 % CECs, corresponding to CEC removal of 2.92 and 27.49 g/d in the CD and JM WWTPs, respectively. The data of this study were further used to evaluate the suitability of the SimpleTreat model for simulating the fate of CECs in WWTPs. The predicted fraction of CECs discharged through the biological treatment effluent were generally within ten-fold difference from the measured results, highlighting its potential for estimating CEC removal in WWTPs.

Emerging and legacy contaminants on the Brazilian southern coast (Santa Catarina): A multi-biomarker approach in oysters Crassostrea gasar (Adanson, 1757)

Coastal environments, such as those in the Santa Catarina State (SC, Brazil), are considered the primary receptors of anthropogenic pollutants. In this study, our objective was to evaluate the levels of emerging contaminants (ECs) and persistent organic pollutants (POPs) in indigenous Crassostrea gasar oysters from different regions of SC coast in the summer season (March 2022). Field collections were conducted in the São Francisco do Sul, Itajaí, Florianópolis and Laguna coastal zones. We analyzed the bioaccumulation levels of 75 compounds, including antibiotics (AB), endocrine disruptors (ED), non-steroidal anti-inflammatory drugs (NSAIDs), polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs) and pesticides. Furthermore, we assessed biomarker responses related to biotransformation, antioxidant defense, heat shock protection and oxidative damage in oysters' gills. Prevalence of ECs was observed in the central and southern regions, while the highest concentrations of POPs were detected in the central-northern regions of SC. Oysters exhibited an induction in biotransformation systems (cyp2au1 and cyp356a1, sult and GST activity) and antioxidant enzymes activities (SOD, CAT and GPx). Higher susceptibility to lipid peroxidation was observed in the animals from Florianópolis compared to other regions. Correlation analyses indicated possible associations between contaminants and environmental variables in the biomarker responses, serving as a warning related to climate change. Our results highlight the influence of anthropogenic activities on SC, serving as baseline of ECs and POPs levels in the coastal areas of Santa Catarina, indicating more critical zones for extensive monitoring, aiming to conserve coastal regions.

Review on ultrasonic technology enhanced biological treatment of wastewater

As a clean, sustainable and efficient technology of wastewater treatment, ultrasonic irradiation has gained special attention in wastewater treatment. It has been widely studied for degrading pollutants and enhancing biological treatment processes for wastewater treatment. This review focuses on the mechanism and updated information of ultrasonic technology to enhance biological treatment of wastewater. The mechanism involved in improving biological treatment by ultrasonic includes: 1) degradation of refractory substances and release carbon from sludges, 2) promotion of mass transfer and change of cell permeability, 3) facilitation of enzyme-catalyzed reactions and 4) influence of cell growth. Based on the above discussion, the effects of ultrasound on the enhancement of wastewater biological treatment processes can be categorized into indirect and direct ways. The indirect effect of ultrasonic waves in enhancing biological treatment is mainly achieved through the use of high-intensity ultrasonic waves. These waves can be used as a pretreatment to improve biodegradability of the wastewater. Moreover, the ultrasonic-treated sludge or its supernatant can serve as a carbon source for the treatment system. Low-intensity ultrasound is often employed to directly enhance the biological treatment of wastewater. The propose of this process is to improve activated sludge, domesticate polyphosphate-accumulating organisms, ammonia-oxidizing bacteria, and anammox bacteria, and achieve speedy start-up of partial nitrification and anammox. It has shown remarkable effects on maintaining stable operation, tolerating adverse conditions (i.e., low temperature, low C/N, etc.), resisting shock load (i.e., organic load, toxic load, etc.), and collapse recovery. These results indicate a promising future for biological wastewater treatment. Furthermore, virous ultrasonic reactor designs were presented, and their potential for engineering application was discussed.

Tracking Aromatic Amines from Sources to Surface Waters

This review examines the environmental occurrence and fate of aromatic amines (AAs), a group of environmental contaminants with possible carcinogenic and mutagenic effects. AAs are known to be partially responsible for the genotoxic traits of industrial wastewater (WW), and AA antioxidants are acutely toxic to some aquatic organisms. Still, there are gaps in the available data on sources, occurrence, transport, and fate in domestic WW and indoor environments, which complicate the prevention of adverse effects in aquatic ecosystems. We review key domestic sources of these compounds, including cigarette smoke and grilled protein-rich foods, and their presence indoors and in aquatic matrices. This provides a basis to evaluate the importance of nonindustrial sources to the overall environmental burden of AAs. Appropriate sampling techniques for AAs are described, including copper-phthalocyanine trisulfonate materials, XAD resins in solid-phase extraction, and solid-phase microextraction methods, which can offer insights into AA sources, transport, and fate. Further discussion is provided on potential progress in the research of AAs and their behavior in an aim to support the development of a more comprehensive understanding of their effects and potential environmental risks.

Effects of dissolved organic matter and halogen ions on phototransformation of pharmaceuticals and personal care products in aquatic environments

Photochemical reactions contribute to the attenuation and transformation of pharmaceuticals and personal care products (PPCPs) in surface natural waters. Nevertheless, effects of DOM and halogen ions on phototransformation of PPCPs remain elusive. This work selected disparate PPCPs as target pollutants to investigate their aquatic phototransformation processes. Results show that PPCPs containing multiple electron-donating groups (-OH, -NH2, -OR, etc.) are more reactive with photochemically produced reactive intermediates (PPRIs) such as triplet DOM (3DOM*), singlet oxygen (1O2), and reactive halogen species (RHSs), relative to PPCPs containing electron-withdrawing groups (-NOR, -COOR, -OCR, etc.). The generation of RHSs as a result of the coexistance of DOM and halide ions changed the contribution of PPRIs to the photochemical conversion of PPCPs during their migration from fresh water to seawater. For PPCPs (AMP, SMZ, PN, NOR, CIP, etc) with highly reactive groups toward RHSs, the generation of RHSs facilitated their photolysis in halide ion-rich waters, where Cl- plays a critical role in the photochemical transformation of PPCPs. Density functional theory (DFT) calculations showed that single electron transfer and H-abstraction are main reaction pathways of RHSs with the PPCPs. These results demonstate the irreplaceable roles of PPRIs and revealing the underlying reaction mechanisms during the phototransformation of PPCPs, which contributes to a better understanding of the environmental behaviors of PPCPs in complex aquatic environments.

Enhanced antibiotic degradation via photo-assisted peroxymonosulfate over graphitic carbon nitride nanosheets/CuBi2O4: Highly efficiency of oxygen activation and interfacial charge transfer

Improving the activation capacity of peroxymonosulfate (PMS) to increase radical and non-radical production is critical for antibiotic degradation. However, how to boost reactive oxygen species (ROS) and speed interfacial charge transfer remains an essential challenge. We report a coupling system of 10 %CNNS/CuBi2O4 photocatalyst and sulfate radical-based advanced oxidation processes (SO4--AOPs) to enhance the activation of PMS and improve antibiotic degradation. Owing to highly efficient oxygen activation and interfacial charge transfer, the degradation efficiency of the photo-assisted PMS system was as high as 51.6 times and 2.8 times that of photocatalyst and SO4--AOPs alone, respectively. Importantly, the highly efficient oxygen activation resulted in the production of O2-, which in turn could utilize the excess electrons generated through efficient interfacial charge transfer to convert into non-radical 1O2. The total organic carbon (TOC) elimination effectiveness of the photo-assisted PMS system reached 82 % via the synergy of radicals and non-radicals (O2-, OH, 1O2, SO4-, h+). This system also had excellent potential for reducing the generation and toxicity of disinfection by-products (DBPs), as evidenced through significant reductions in concentrations of trichloromethane (TCM), dichloroacetic acid (DCAA), and trichloronitromethane (TCNM) by 76 %, 64 %, and 35 %, respectively, providing an effective and eco-friendly strategy for antibiotic treatment.

Effects of solution chemistry on dielectric barrier atmospheric non-thermal plasma for operative degradation of antiretroviral drug nevirapine

The global prevalence of human immunodeficiency virus/acquired immunodeficiency syndrome (HIV/AIDS) has been an environmental menace. Tons of drug wastes from antiretroviral therapy are released into the environment annually. We, for the first time, employed the novel dielectric barrier atmospheric non-thermal plasma (DBANP) discharge, to mitigate the inadvertent pollution arising from the antiretroviral therapy. A 40-min treatment of nevirapine achieved >94 % (0.075 min-1) removal efficiency at discharge power of 63.5 W and plasma working gas of atmospheric air. Chemical probes confirmed •OH, ONOO- and eaq- as the dominant reactive species whilst further revealing the reaction acceleration role of NaNO3 and CCl4 which are known reaction terminators. The commonly coexisting inorganic anions potentiated nevirapine removal with over 98 % efficiency, achieving the highest rate constant of 0.148 min-1 in this study. Moreover, the initial solution pH (1.5-11.1) was no limiting factor either. The insensitivity of the DBANP discharge to actual water matrices was an eminent inference of its potential applicability in practical conditions. With reference to data obtained from the liquid chromatography-mass spectrometer analysis, nevirapine degradation pathway was proposed. A nucleophilic attack by ONOO- at the cyclopropyl group and •OH attack at the carbonyl carbon of the amide group, respectively, initiated nevirapine degradation process. It is anticipated that the findings herein, will provide new insights into antiretroviral drug waste management in environmental waters using the innovative and green non-thermal plasma process.

Multi-level FeCo/N-doped carbon nanosheet for peroxymonosulfate oxidation and sterilization inactivation

Magnetic carbon-based catalysts with environmental friendliness have exhibited prominent effects on advanced oxidation processes. Herein, a multi-level FeCo/N-doped carbon nanosheet (FeCo/CNS) was synthesized by facile impregnation iron-cobalt salt onto cotton and followed by confined pyrolysis. We identified excellent advantages of the modified FeCo/CNS materials: (i) The convenience of the synthesis method and (ii) The dual effect of sterilization and contaminant degradation achieved through the FeCo/CNS-activated Peroxymonosulfate (PMS). The comparative experimental showed that FeCo/CNS could provide favorable catalytic performance, completely removing bisphenol A (BPA) and tetracycline (TC) within 5 min. Moreover, the potent sterilization properties against Staphylococcus aureus and Escherichia coli were also verified. Analysis of the degradation pathway confirmed the existence of intermediates, and toxicological research demonstrated that the toxicity of the degradation intermediates of BPA gradually decreased over time. Our research provided an excellent application of FeCo/CNS in PMS oxidation and sterilization inactivation.

Trace organic contaminants in lake waters: Occurrence and environmental risk assessment at the national scale in Canada

Numerous contaminants are produced and used daily, a significant fraction ultimately finding their way into natural waters. However, data on their distribution in lakes is lacking. To address this gap, the presence of 54 trace organic contaminants (TrOCs), representative of various human activities, was investigated in the surface water of 290 lakes across Canada. These lakes ranged from remote to highly impacted by human activities. In 88% of the sampled lakes, contaminants were detected, with up to 28 detections in a single lake. The compounds most frequently encountered were atrazine, cotinine, and deethylatrazine, each of which was present in more than a third of the lakes. The range of detected concentrations was from 0.23 ng/L to about 2200 ng/L for individual compounds, while the maximum cumulative concentration exceeded 8100 ng/L in a single lake. A risk assessment based on effect concentrations for three aquatic species (Pimephales promelas, Daphnia magna, and Tetrahymena pyriformis) was conducted, revealing that 6% of lakes exhibited a high potential risk for at least one species. In 59% of lakes, some contaminants with potential sub-lethal effects were detected, with the detection of up to 17 TrOCs with potential impacts. The results of this work provide the first reference point for monitoring the evolution of contamination in Canadian lakes by TrOCs. They demonstrate that a high proportion of the sampled lakes bear an environmentally relevant anthropogenic chemical footprint.

Eat seldom is better than eat frequently: Pharmaceuticals degradation kinetics, enantiomeric profiling and microorganisms in moving bed biofilm reactors are affected by feast famine cycle times

Feast-famine (FF) regimes improved the removal of recalcitrant pharmaceuticals in moving bed biofilm reactors (MBBRs), but the optimal FF cycle remained unresolved. The effects of FF cycle time on the removal of bulk substrates (organic carbon and nitrogen) and trace pharmaceuticals by MBBR are systematically evaluated in this study. The feast to famine ratio was fixed to 1:2 to keep the same loading rate, but the time for the FF cycles varied from 18 h to 288 h. The MBBR adapted to the longest FF cycle time (288 h equaling 48 × HRT) resulted in significantly higher degradation rates (up to +183%) for 12 out of 28 pharmaceuticals than a continuously fed (non-FF) reactor. However, other FF cycle times (18, 36, 72 and 144 h) only showed a significant up-regulation for 2-3 pharmaceuticals compared to the non-FF reactor. Enantioselective degradation of metoprolol and propranolol occurred in the second phase of a two phase degradation, which was different for the longer FF cycle time. N-oxidation and N-demethylation pathways of tramadol and venlafaxine differed across the FF cycle time suggestin the FF cycle time varied the predominant transformation pathways of pharmaceuticals. The abundance of bacteria in the biofilms varied considerably between different FF cycle times, which possibly caused the biofilm to remove more recalcitrant bulk organic C and pharmaceuticals under long cycle times.

Development of quantitative structure activity relationships (QSARs) for predicting the aggregation of TiO2 nanoparticles under favorable conditions

This study developed multi-linear regression (MLR) quantitative structure-activity relationships (QSARs) to predict n-TiO2 aggregation in the presence of high concentrations of representative emerging organic contaminants (EOCs), which presented favorable conditions to interaction with n-TiO2. The largest diameter change (Δ 517 nm at 0 h and Δ 1164 nm at 12 h) of n-TiO2 was observed by estrone, while the smallest diameter change (Δ -114 nm at 0 h and - 4 nm at 12 h) was observed by lincomycin during experimental periods. In addition, the zeta potential changes of n-TiO2 were observed that the biggest changes were observed by 17β-estradiol (-1.3 mV) and alachlor (-10.02 mV) at 0 h, while 17β-estradiol (-1.31 mV) and pendimethalin (-11.4 mV) showed the biggest changes at 12 h comparing to control. These changes of n-TiO2 diameter and zeta potential may implicate the effects of unique physico-chemical properties of each EOC on the surface modification of n-TiO2. Based on the interaction results, this study investigated the QSARs between n-TiO2 aggregation and physico-chemical descriptors of EOCs with 7 representative descriptors (pKa, Cw, log Kow, M.W., P.S.A., M.V., # of HBD) for predicting n-TiO2 aggregation rate kinetics at 0 h and 12 h by applying MATLAB statistical methods (model 1 - fitlm and model 2 - stepwiselm). In a model 1, QSARs showed the good coefficients of determination (R2 = 0.92) at 0 h and (R2 = 0.87) at 12 h with 7 descriptors. In a model 2, QSARs showed the goodness of fit of a model (R2 = 0.9998) with 8 descriptors (pKa, Cw, log Kow, M.W., P.S.A., M.V., #HBD, pKa⋅#H bond donors) at 0 h, while QSARs showed the coefficients of determination (R2 = 0.68) with 2 descriptors (pKa, M.V.) at 12 h. Particularly, we observed that some descriptors of EOCs such as pKa and # of HBD having polarity have more influenced on the n-TiO2 aggregation rate kinetics. Our developed QSARs demonstrated that the 7 descriptors of EOCs were significantly effective descriptors for predicting n-TiO2 aggregation rate kinetics in favorable conditions, which may implicate the complexity interactions between heterogeneous surfaces of n-TiO2 and physico-chemical properties of EOCs.

Influence mechanism of anions on iron doping into swine bone char: Promoting non-radical oxidation of acetaminophen in a Fenton-like system

The application of iron-doped biochar in peroxymonosulfate (PMS) activation systems has gained increasing attention due to their effectiveness and environmental friendliness in addressing environmental issues. However, the behavioral mechanism of iron doping and the detailed 1O2 generation mechanism in PMS activation systems remain ambiguous. Here, we investigated the effects of three anions (Cl-, NO3-and SO42-) on the process of iron doping into bone char, leading to the synthesis of three iron-doped bone char (Fe-ClBC, Fe-NBC and Fe -SBC). These iron-doped bone char were used to catalyze PMS to degrade acetaminophen (APAP) and exhibited the following activity order: Fe-ClBC > Fe-NBC > Fe-SBC. Characterization results indicated that iron doping primarily occurred through the substitution of calcium in hydroxyapatite within BC. In the course of the impregnation, the binding of SO42- and Ca2+ hindered the exchange of iron ions, resulting in lower catalytic activity of Fe-SBC. The primary reactive oxygen species in the Fe-ClBC/PMS and Fe-NBC/PMS systems were both 1O2. 1O2 is produced through O2•- conversion and PMS self-dissociation, which involves the generation of metastable iron intermediates and electron transfer within iron species. The presence of oxygen vacancies and more carbon defects in the Fe-ClBC catalyst facilitates 1O2 generation, thereby enhancing APAP degradation within the Fe-ClBC/PMS system. This study is dedicated to in-depth exploration of the mechanisms underlying iron doping and defect materials in promoting 1O2 generation.

Unveiling intricate transformation pathways of emerging contaminants during wastewater treatment processes through simplified network analysis

As the key stage for purifying wastewater, elimination of emerging contaminants (ECs) is found to be fairly low in wastewater treatment plants (WWTPs). However, less knowledge is obtained regarding the transformation pathways between various chemical structures of ECs under different treatment processes. This study unveiled the transformation pathways of ECs with different structures in 15 WWTPs distributed across China by simplified network analysis (SNA) we proposed. After treatment, the molecular weight of the whole component of wastewater decreased and the hydrophilicity increased. There are significant differences in the structure of eliminated, consistent and formed pollutants. Amino acids, peptides, and analogues (AAPAs) were detected most frequently and most removable. Benzenoids were refractory. Triazoles were often produced. The high-frequency reactions in different WWTPs were similar, (de)methylation and dehydration occurred most frequently. Different biological treatment processes performed similarly, while some advanced treatment processes differed, such as a significant increase of -13.976 (2HO reaction) paired mass distances (PMDs) in the chlorine alone process. Further, the common structural transformation was uncovered. 4 anti-hypertensive drugs, including irbesartan, valsartan, olmesartan, and losartan, were identified, along with 22 transformation products (TPs) of them. OH2 and H2O PMDs occurred most frequently and in 80.81 % of the parent-transformation product pairs, the intensity of the product was higher than parent in effluents, whose risk should be considered in future assessment activity. Together our results provide a macrography perspective on the transformation processes of ECs in WWTPs. In the future, selectively adopting wastewater treatment technology according to structures is conductive for eliminating recalcitrant ECs in WWTPs.

Environmental health hazards of untreated livestock wastewater: potential risks and future perspectives

Due to technological and economic limitations, waste products such as sewage and manure generated in livestock farming lack comprehensive scientific and centralized treatment. This leads to the exposure of various contaminants in livestock wastewater, posing potential risks to both the ecological environment and human health. This review evaluates the environmental and physical health risks posed by common pollutants in livestock wastewater and outlines future treatment methods to mitigate these risks. Residual wastes in livestock wastewater, including pathogenic bacteria and parasites surviving after epidemics or diseases on various farms, along with antibiotics, organic wastes, and heavy metals from farming activities, contribute to environmental damage and pose risks to human health. As the livestock industry's development increasingly impacts society's future negatively, addressing the issue of residual wastes in livestock wastewater discharge becomes imperative. Ongoing advancements in wastewater treatment systems are consistently updating and refining practices to effectively minimize waste exposure at the discharge source, mitigating risks to environmental ecology and human health. This review not only summarizes the "potential risks of livestock wastewater" but also explores "the prospects for the development of wastewater treatment technologies" based on current reports. It offers valuable insights to support the long-term and healthy development of the livestock industry and contribute to the sustainable development of the ecological environment.

Emerging environmental contaminants: Sources, effects on biodiversity and humans, remediation, and conservation implications

Ecosystems, biodiversity, and the human population all depend on a quality or uncontaminated environment. Quality environment provides people and wildlife access to nutrition, medications, dietary supplements, and other ecosystem services. The conservation of biodiversity-that is, species richness, abundance, heredities, and diversity-as well as the control of climate change are facilitated by such an uncontaminated environment. However, these advantages are jeopardized by newly emerging environmental chemical contaminants (EECCs) brought on by increased industrialization and urbanization. In developing countries, inadequate or poor environmental policies, infrastructure, and national standards concerning the usage, recycling, remediation, control, and management of EECCs hasten their effects. EECCs in these countries negatively affect biodiversity, ecological services and functions, and human health. This review reveals that the most deprived or vulnerable local communities in developing countries are those residing near mining or industrial areas and cultivating their crops and vegetables on contaminated soils, as is wildlife that forages or drinks in EECC-contaminated water bodies. Yet, people in these countries have limited knowledge about EECCs, their threats to human well-being, ecosystem safety, and the environment, as well as remediation technologies. Besides, efforts to efficiently control, combat, regulate, and monitor EECCs are limited. Thus, the review aims to increase public knowledge concerning EECCs in developing countries and present a comprehensive overview of the current status of EECCs. It also explores the sources and advancements in remediation techniques and the threats of EECCs to humans, ecosystems, and biodiversity.

Emerging pollutants in textile wastewater: an ecotoxicological assessment focusing on surfactants

Water and several chemicals, including dyestuffs, surfactants, acids, and salts, are required during textile dyeing processes. Surfactants are harmful to the aquatic environment and induce several negative biological effects in exposed biota. In this context, the present study aimed to assess acute effects of five surfactants, comprising anionic and nonionic classes, and other auxiliary products used in fiber dyeing processes to aquatic organisms Vibrio fischeri (bacteria) and Daphnia similis (cladocerans). The toxicities of binary surfactant mixtures containing the anionic surfactant dodecylbenzene sulfonate + nonionic fatty alcohol ethoxylate and dodecylbenzene sulfonate + nonionic alkylene oxide were also evaluated. Nonionic surfactants were more toxic than anionic compounds for both organisms. Acute nonionic toxicity ranged from 1.3 mg/L (fatty alcohol ethoxylate surfactant) to 2.6 mg/L (ethoxylate surfactant) for V. fischeri and from 1.9 mg/L (alkylene oxide surfactant) to 12.5 mg/L (alkyl aryl ethoxylated and aromatic sulfonate surfactant) for D. similis, while the anionic dodecylbenzene sulfonate EC50s were determined as 66.2 mg/L and 19.7 mg/L, respectively. Both mixtures were very toxic for the exposed organisms: the EC50 average in the anionic + fatty alcohol ethoxylate mixture was of 1.0 mg/L ± 0.11 for V. fischeri and 4.09 mg/L ± 0.69 for D. similis. While the anionic + alkylene oxide mixture, EC50 of 3.34 mg/L for D. similis and 3.60 mg/L for V. fischeri. These toxicity data suggested that the concentration addition was the best model to explain the action that is more likely to occur for mixture for the dodecylbenzene sulfonate and alkylene oxide mixtures in both organisms. Our findings also suggest that textile wastewater surfactants may interact and produce different responses in aquatic organisms, such as synergism and antagonism. Ecotoxicological assays provide relevant information concerning hazardous pollutants, which may then be adequately treated and suitably managed to reduce toxic loads, associated to suitable management plans.

An Overview of Degradation Strategies for Amitriptyline

Antidepressant drugs play a crucial role in the treatment of mental health disorders, but their efficacy and safety can be compromised by drug degradation. Recent reports point to several drugs found in concentrations ranging from the limit of detection (LOD) to hundreds of ng/L in wastewater plants around the globe; hence, antidepressants can be considered emerging pollutants with potential consequences for human health and wellbeing. Understanding and implementing effective degradation strategies are essential not only to ensure the stability and potency of these medications but also for their safe disposal in line with current environment remediation goals. This review provides an overview of degradation pathways for amitriptyline, a typical tricyclic antidepressant drug, by exploring chemical routes such as oxidation, hydrolysis, and photodegradation. Connex issues such as stability-enhancing approaches through formulation and packaging considerations, regulatory guidelines, and quality control measures are also briefly noted. Specific case studies of amitriptyline degradation pathways forecast the future perspectives and challenges in this field, helping researchers and pharmaceutical manufacturers to provide guidelines for the most effective degradation pathways employed for minimal environmental impact.

Bioinspired Stevia rebaudiana Green Zinc Oxide Nanoparticles for the Adsorptive Removal of Antibiotics from Water

Green zinc oxide nanoparticles (ZnO NPs) synthesized using Stevia rebaudiana as a reducing agent were investigated as ecofriendly adsorbents for the removal of the antibiotics ciprofloxacin (CIP) and tetracycline (TET) from water. Green ZnO NPs were synthesized using a rapid novel approach that did not require annealing or calcination at high temperatures to produce mesoporous NPs with a size range of 37.36-71.33 nm, a specific surface area of 15.28 m2/g, and a negative surface charge of -15 mV at pH 5. The green ZnO NPs exhibited an antioxidant activity of 85.57% at 250 μg/mL and an antibacterial activity with MIC and MBC of 50 and 100 mg/mL, respectively, against both Escherichia coli and Staphylococcus aureus. The best adsorption performance was achieved using a 4 g/L dose and pH 5, yielding, respectively, 86.77 ± 0.82% removal and 27.07 ± 0.26 mg/g adsorption capacity for CIP at 10 mg/L and 67.86 ± 3.41% and 15.88 ± 0.37 mg/g for TET at 25 mg/L. The green ZnO NPs achieved 79.71% ± 0.28 and 61.55% ± 0.53 removal of 10 mg/L CIP and 25 mg/L TET, respectively, in a spiked tap water binary system of the two contaminants. Adsorption of CIP and TET occurred mainly via electrostatic interactions, whereby CIP was bound more strongly than TET by virtue of its charge and size. The synthesis and adsorption processes were evaluated by a stepwise regression statistical model to optimize their parameters. Lastly, the green ZnO NPs were regenerated and reused for 5 cycles, indicating their functionality as simple, reusable, and low-cost adsorbents for the removal of CIP and TET from wastewater, in accordance with SDGs #6 and 12 for the sustainable management of water.

Occurrence, spatiotemporal trends, fate, and treatment technologies for microplastics and organic contaminants in biosolids: A review

This review provides a comprehensive overview of the occurrence, fate, treatment and multi-criteria analysis of microplastics (MPs) and organic contaminants (OCs) in biosolids. A meta-analysis was complementarily analysed through the literature to map out the occurrence and fate of MPs and 10 different groups of OCs. The data demonstrate that MPs (54.7% occurrence rate) and linear alkylbenzene sulfonate surfactants (44.2% occurrence rate) account for the highest prevalence of contaminants in biosolids. In turn, dioxin, polychlorinated biphenyls (PCBs) and phosphorus flame retardants (PFRs) have the lowest rates (<0.01%). The occurrence of several OCs (e.g., dioxin, per- and polyfluoroalkyl substances, polycyclic aromatic hydrocarbons, pharmaceutical and personal care products, ultraviolet filters, phosphate flame retardants) in Europe appear at higher rates than in Asia and the Americas. However, MP concentrations in biosolids from Australia are reported to be 10 times higher than in America and Europe, which required more measurement data for in-depth analysis. Amongst the OC groups, brominated flame retardants exhibited exceptional sorption to biosolids with partitioning coefficients (log Kd) higher than 4. To remove these contaminants from biosolids, a wide range of technologies have been developed. Our multicriteria analysis shows that anaerobic digestion is the most mature and practical. Thermal treatment is a viable option; however, it still requires additional improvements in infrastructure, legislation, and public acceptance.

Futuristic advancements in phytoremediation of endocrine disruptor Bisphenol A: A step towards sustainable pollutant degradation for rehabilitated environment

Bisphenol A (BPA) accumulates in the environment at lethal concentrations because of its high production rate and utilization. BPA, originating from industrial effluent, plastic production, and consumer products, poses serious risks to both the environment and human health. The widespread aggregation of BPA leads to endocrine disruption, reactive oxygen species-mediated DNA damage, epigenetic modifications and carcinogenicity, which can disturb the normal homeostasis of the body. The living being in a population is subjected to BPA exposure via air, water and food. Globally, urinary analysis reports have shown higher BPA concentrations in all age groups, with children being particularly susceptible due to its occurrence in items such as milk bottles. The conventional methods are costly with a low removal rate. Since there is no proper eco-friendly and cost-effective degradation of BPA reported so far. The phytoremediation, green-biotechnology based method which is a cost-effective and renewable resource can be used to sequestrate BPA. Phytoremediation is observed in numerous plant species with different mechanisms to remove harmful contaminants. Plants normally undergo several improvements in genetic and molecular levels to withstand stress and lower levels of toxicants. But such natural adaptation requires more time and also higher concentration of contaminants may disrupt the normal growth, survival and yield of the plants. Therefore, natural or synthetic amendments and genetic modifications can improve the xenobiotics removal rate by the plants. Also, constructed wetlands technique utilizes the plant's phytoremediation mechanisms to remove industrial effluents and medical residues. In this review, we have discussed the limitations and futuristic advancement strategies for degrading BPA using phytoremediation-associated mechanisms.

Quality and risk management frameworks for biosolids: An assessment of current international practice

Biosolids, a product of wastewater treatment, provide a valuable resource, but to optimize the use of this resource it is necessary to manage risks posed to public health and the environment. Key requirements include identifying contaminant sources and providing barriers to ensure containment and treatment while maintaining the viability and value of biosolids products. Responsibility for managing biosolids is the remit of many stakeholders but primarily it rests with private and public wastewater facilities. The global variabilities in the way biosolids resources are acknowledged, applied, and managed are substantial. For example, some countries are increasing incineration because of their ability to remove contaminants while others have experienced a proportional decrease in incineration dependent on industrial resources or regarding resource recovery costs and needs. Some jurisdictions focus on energy recovery and others on land application. A risk management framework is a tool that may provide a suitable holistic approach to biosolids management. With this focus, current instruments in practice globally to manage biosolids were assessed for the degree to which they have adopted a risk management framework. To form a basis for this assessment a set of criteria was established by concept mapping several internationally recognized standards. Guidelines for a range of developed and developing countries were then assessed against these criteria. That process enabled the identification of which current practices were holistic in terms of applying biosolids risk management principles from production to end-use. Through this process, risk management gaps and vulnerabilities were identified. The results reveal that the incorporation of risk standards into risk management frameworks around the world is variable for the presence of risk criteria and the scale of detail provided. Contaminant concentrations need perspective within the changing risk landscape for stakeholders and the environment while jointly the opportunities and contaminant challenges require solutions that balance risks.

Evaluation of different QuEChERS-based methods for the extraction of 48 wastewater-derived organic contaminants from soil and lettuce root using high-resolution LC-QTOF with MRMHR and SWATH acquisition modes

The reuse of treated wastewater in agriculture is an important route of introducing a large number of organic contaminants into the agroecosystem. In this study, a modified QuEChERS-based approach was developed for rapid, simple, and simultaneous extraction of 48 organic wastewater-derived contaminants from soil and lettuce root. Twenty-two different (modification) scenarios of the known (or original) QuEChERS method have been tested, in order to obtain best and well-compromised recoveries for all target compounds for soil and roots. Finally, a common method was chosen for both matrices consisting of a single extraction step using EDTA-Mcllvaine buffer and the unbuffered Original QuEChERS salts. Method performance was accomplished by liquid chromatography coupled with high-resolution mass spectrometry on a QToF-MS system using two different acquisition modes, the ultra-fast high-resolution multiple reaction monitoring (MRMHR) mode and the innovative Sequential Window Acquisition of All Theoretical Fragment-Ion (SWATH) mode. Performance characterization was evaluated in terms of recovery, linearity, intra-day precision, method detection limits (MDLs), method quantification limits (MQLs), and matrix effect (ME). Recoveries in MRMHR mode ranged from 63 to 111% and 54 to 104% for lettuce root and soil, respectively, for most of compounds in MRMHR mode and from 56 to 121% and 54 to 104% for lettuce root and soil, respectively, for most of compounds in SWATH. Whereas, MQLs ranged from 0.03 to 0.92 ng g-1 in MRMHR and from 0.03 to 82 ng g-1 in SWATH for lettuce root, and from 0.02 to 0.44 ng g-1 in MRMHR and 0.02 to 0.14 ng g-1 in SWATH for soil. The method was then applied to follow the target compounds in soil and lettuce root, where the system lettuce-soil was irrigated with treated wastewater under real greenhouse conditions. Five and 17 compounds were detected in lettuce root and soil, respectively.