Water Analysis: Emerging Contaminants and Current Issues

Unlocking high-efficiency decontamination by building a novel heterogeneous catalytic reduction system of thiourea dioxide/biochar

Herein, we reported a new contaminant purification paradigm, which enabled highly efficient reductive denitration and dechlorination using a green, stable reducing agent thiourea dioxide (TDO) coupled with biochar (BC) over a wide pH range under anoxic conditions. Specifically, BC acted as both activators and electron shuttles for TDO decomposition to achieve complete anoxic degradation of p-nitrophenol (PNP), p-nitroaniline, 4-chlorophenol and 2,4-dichlorophenol within 2 h. During this process, multiple strongly reducing species (i.e., SO22-, SO2•- and e-/H•) were generated in BC/TDO systems, accounting for 13.3%, 9.7% and 75.5% of PNP removal, respectively. While electron transfer between TDO and H+ or contaminants mediated by BC led to H• generation and contaminant reduction. These processes depended on the electron-accepting capacity and electron-conducting domains of biochar. Significantly, the BC/TDO systems were highly efficient at a pH of 2.0-8.0, especially under acidic conditions, which performed robustly in common natural water constituents.

The ideal model for determination the formation potential of priority DBPs during chlorination of free amino acids

Amino acids (AAs) account for about 15-35% of dissolved organic nitrogen (DON), and are known as the important precursors of nitrogenous disinfection by-products (N-DBPs). Determining the formation potential (FP) of AAs to DBPs is used to reveal the key precursors of DBPs for further control, while the ideal method for N-DBPs FP of AAs during chlorination is not revealed. In this study, the ideal FP test models for five classes of priority DBPs during chlorination of four representative AAs (accounted for about 35% of total AAs) were analyzed. For haloaldehydes (HALs), haloketones (HKs), haloacetonitriles (HANs), haloacetamides (HAMs), and halonitromethanes (HNMs), their FPs during chlorination of four AAs were 0.1-13.0, 0.01-1.1, 0.1-104, not detectable (nd)-173, and nd-0.4 μg/mg, respectively. The FPs of priority DBPs had significant deviations between different FP test models and different tested AAs. For HALs, the model, whose chlorine dosage was determined by 15 × molar concentration of AAs [Cl (mM) = 15 × M](named: model II), was the ideal model. For HKs, model II was also the ideal FP test model for AAs with ≤3 carbons, while for AAs with 4 carbons, the model, whose chlorine dosage was determined by keeping the residual chlorine at 1 ± 0.2 mg/L after 24 h of reaction (named: model 4), was the ideal model. For HANs and HNMs, model 4 was the ideal FP test model for most of the studied AAs. The performance of HAMs during chlorination of amino acids was totally different from other P-DBPs, and model 3 was recommended to be the ideal model, in which chlorine dosage was determined by 3 × mass concentration of AAs [Cl (mg/L) = X × DOC]. This study is a reference that helps researchers select an ideal model for N-DBPs FP study of AAs.

Occurrence, efficiency of treatment processes, source apportionment and human health risk assessment of pharmaceuticals and xenoestrogen compounds in tap water from some Ghanaian communities

The occurrence of pharmaceuticals and xenoestrogen compounds (PXCs) in drinking water presents a dire human health risk challenge. The problem stems from the high anthropogenic pollution load on source water and the inefficiencies of the conventional water treatment plants in treating PXCs. This study assessed the PXCs levels and the consequential health risks of exposure to tap water from selected Ghanaian communities as well as that of raw water samples from the respective treatment plants. Thus the PXCs treatment efficiency of two drinking water treatment plants in the metropolises studied was also assessed. The study also conducted source apportionment of the PXCs in the tap water. Twenty six (26) tap and raw water samples from communities in the Cape Coast and Sekondi-Takoradi metropolises were extracted using SPE cartridges and analysed for PXCs using Ultra-fast-HPLC-UV instrument. Elevated levels of PXCs up to 24.79 and 22.02 μg/L were respectively recorded in raw and tap water samples from the metropolises. Consequently, elevated non-cancer health risk (HI > 1) to residential adults were found for tap water samples from Cape Coast metropolis and also for some samples from Sekondi-Takoradi metropolis. Again, elevated cumulative oral cancer risks >10-5 and dermal cancer risk up to 4 × 10-5 were recorded. The source apportionment revealed three significant sources of PXCs in tap water samples studied. The results revealed the inefficiency of the treatment plants in removing PXCs from the raw water during treatments. The situation thus requires urgent attention to ameliorate it, safeguarding public health. It is recommended that the conventional water treatment process employed be augmented with advanced treatment technologies to improve their efficacy in PXCs treatment.

Suppressing Organic Bromine but Promoting Bromate: Is the Ultraviolet/Ozone Process a Double-Edged Sword for the Toxicity of Wastewater to Mammalian Cells?

Brominated byproducts and toxicity generation are critical issues for ozone application to wastewater containing bromide. This study demonstrated that ultraviolet/ozone (UV/O3, 100 mJ/cm2, 1 mg-O3/mg-DOC) reduced the cytotoxicity of wastewater from 14.2 mg of pentol/L produced by ozonation to 4.3 mg of pentol/L (1 mg/L bromide, pH 7.0). The genotoxicity was also reduced from 1.65 to 0.17 μg-4-NQO/L by UV/O3. Compared with that of O3 alone, adsorbable organic bromine was reduced from 25.8 to 5.3 μg/L by UV/O3, but bromate increased from 32.9 to 71.4 μg/L. The UV/O3 process enhanced the removal of pre-existing precursors (highly unsaturated and phenolic compounds and poly aromatic hydrocarbons), while new precursors were generated, yet the combined effect of UV/O3 on precursors did not result in a significant change in toxicity. Instead, UV radiation inhibited HOBr concentration through both rapid O3 decomposition to reduce HOBr production and decomposition of the formed HOBr, thus suppressing the AOBr formation. However, the hydroxyl radical-dominated pathway in UV/O3 led to a significant increase of bromate. Considering both organic bromine and bromate, the UV/O3 process effectively controlled both cytotoxicity and genotoxicity of wastewater to mammalian cells, even though an emphasis should be also placed on managing elevated bromate. Futhermore, other end points are needed to evaluate the toxicity outcomes of the UV/O3 process.

An iron metal-organic framework-based electrochemical sensor for identification of Bisphenol-A in groundwater samples

Bisphenol A (BPA) is an endocrine disruptor that leaches into food and is significantly employed in food and beverage storage, and source water cycles. To ensure an outstanding and sustainable biosphere while safeguarding human health and well-being, BPA detection is essential, necessitating an efficient detection methodology. Here, we describe an easy-to-use, inexpensive, and overly sensitive electrochemical detector that uses Fe-MOF nanotextures for identifying BPA in groundwater. This sensing electrode device combines the excellent guest interaction potential of organic ligands with the substantial surface area of metal. Using various analytical techniques including scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FT-IR), and powder X-ray diffraction (XRD), the structural and physicochemical behaviors of the as-synthesized material were evaluated. Electrochemical BPA detection was enabled by a diffusion-controlled oxidation procedure with a comparable number of both protons and electrons. With a 0.1 μM detection limit, the sensor displayed a linear sensitivity of around 0.1 μM and 15 μM. Additionally, the sensors demonstrated an outstanding recovery with actual water samples as well as a repeatable and steady performance over the course of a month exhibiting minimal interference from typical inorganic and organic species. Due to its notable sensitivity, inexpensive cost, robust selectivity, excellent repeatability, and reuse ability, the electroanalytical possibilities of the Fe-MOF-modified GCE suggest that the device can be implemented into real-world applications in its primed condition.

Extrapolation of cytotoxic masked effects in planar in vitro assays

The masking of specific effects in in vitro assays by cytotoxicity is a commonly known phenomenon. This may result in a partial or complete loss of effect signals. For common in vitro assays, approaches for identifying and quantifying cytotoxic masking are partly available. However, a quantification of cytotoxicity-affected signals is not possible. As an alternative, planar bioassays that combine high-performance thin layer chromatography with in vitro assays, such as the planar yeast estrogen screen (p-YES), might allow for a quantification of cytotoxically affected signals. Affected signals form a typical ring structure with a supressed or completely lacking centre that results in a double peak chromatogram. This study investigates whether these double peaks can be used for fitting a peak function to extrapolate the theoretical, unaffected signals. The precision of the modelling was evaluated for four individual peak functions, using 42 ideal, undistorted peaks from estrogenic model compounds in the p-YES. Modelled ED50-values from bisphenol A (BPA) experiments with cytotoxically disturbed signals were 13 times higher than for the apparent data without compensation for cytotoxicity (320 ± 63 ng versus 24 ± 17 ng). This finding has a high relevance for the modelling of mixture effects according to concentration addition that requires unaffected, complete dose-response relationships. Finally, we applied the approach to results of a p-YES assay on leachate samples of an elastomer material used in water engineering. In summary, the fitting approach enables the quantitative evaluation of cytotoxically affected signals in planar in vitro assays and also has applications for other fields of chemical analysis like distorted chromatography signals.

Cytotoxicity of emerging halophenylacetamide disinfection byproducts in drinking water: Mechanism and prediction

Halophenylacetamides (HPAcAms) have been identified as a new group of nitrogenous aromatic disinfection byproducts (DBPs) in drinking water, but the toxicity mechanisms associated with HPAcAms remain almost completely unknown. In this work, the cytotoxicity of HPAcAms in human hepatoma (HepG2) cells was evaluated, intracellular oxidative stress/damage levels were analyzed, their binding interactions with antioxidative enzyme were explored, and a quantitative structure-activity relationship (QSAR) model was established. Results indicated that the EC50 values of HPAcAms ranged from 2353 μM to 9780 μM, and the isomeric structure as well as the type and number of halogen substitutions could obviously induce the change in the cytotoxicity of HPAcAms. Upon exposure to 2-(3,4-dichlorophenyl)acetamide (3,4-DCPAcAm), various important biomarkers linked to oxidative stress and damage, such as reactive oxygen species, 8‑hydroxy-2-deoxyguanosine, and cell apoptosis, exhibited a significant increase in a dose-dependent manner. Moreover, 3,4-DCPAcAm could directly bind with Cu/Zn-superoxide dismutase and induce the alterations in the structure and activity, and the formation of complexes was predominantly influenced by the van der Waals force and hydrogen bonding. The QSAR model supported that the nucleophilic reactivity as well as the molecular compactness might be highly important in their cytotoxicity mechanisms in HepG2 cells, and 2-(2,4-dibromophenyl)acetamide and 2-(3,4-dibromophenyl)acetamide deserved particular attention in future studies due to the relatively higher predicted cytotoxicity. This study provided the first comprehensive investigation on the cytotoxicity mechanisms of HPAcAm DBPs.

Non-target screening and prioritization of organic contaminants in seawater desalination and their ecological risk assessment

The impact of desalination brine on the marine environment is a global concern. Regarding this, salinity is generally accepted as the major environmental factor in desalination concentrate. However, recent studies have shown that the influence of organic contaminants in brine cannot be ignored. Therefore, a non-targeted screening method based on comprehensive two-dimensional gas chromatography-quadrupole mass spectrometry (GC × GC-qMS) was developed for identifying organic contaminants in the desalination brine. A total of 404 compounds were tentatively identified from four seawater desalination plants (three reverse osmosis plants and one multiple effect distillation plant) in China. The identified compounds were prioritized based on their persistence, bioaccumulation, ecotoxicity, usage, and detection frequency. Twenty-one (21) compounds (seven phthalates, ten pesticides, four trihalomethanes) were then selected for further quantitative analysis and ecological risk assessment, including compounds from the priority list along with substances from the same chemical classes. Ecologically risky substances in brine include diisobutylphthalate and bis(2-Ethylhexyl) phthalate, atrazine and acetochlor, and bromoform. Most of the contaminants come from raw seawater, and no high risk contaminants introduced by the desalination process have been found except for disinfection by-products. In brine discharge management, people believed that all pollution in raw seawater was concentrated by desalination process. This study shows that not all pollutants are concentrated during the desalination process. In this study, the total concentration of pesticide in the brine increased by 58.42%. The concentration of ∑PAEs decreased by 13.65% in reverse osmosis desalination plants and increased by 10.96% in the multi-effect distillation plant. The concentration of trihalomethane increased significantly in the desalination concentrate. The change in the concentration of pollutants in the desalination concentrate was related to the pretreatment method and the chemical characteristics of the contaminants. The method and results given in this study hinted a new idea to identify and control the environmental impact factors of brine.

Direct Determination of Absolute Radical Quantum Yields in Hydroxyl and Sulfate Radical-Based Treatment Processes

The absolute radical quantum yield (Φ ) is a critical parameter to evaluate the efficiency of radical-based processes in engineered water treatment. However, measuring Φ is fraught with challenges, as current quantification methods lack selectivity, specificity, and anti-interference capabilities, resulting in significant error propagation. Herein, we report a direct and reliable time-resolved technique to determine Φ at pH 7.0 for commonly used radical precursors in advanced oxidation processes. For H2O2 and peroxydisulfate (PDS), the values of Φ •OH and Φ SO 4 • - at 266 nm were measured to be 1.10 ± 0.01 and 1.46 ± 0.05, respectively. For peroxymonosulfate (PMS), we developed a new approach to determine Φ • OH PMS with terephthalic acid as a trap-and-trigger probe in the nonsteady state system. For the first time, the Φ • OH PMS value was measured to be 0.56 by the direct method, which is stoichiometrically equal to Φ SO 4 • - PMS (0.57 ± 0.02). Additionally, radical formation mechanisms were elucidated by density functional theory (DFT) calculations. The theoretical results showed that the highest occupied molecular orbitals of the radical precursors are O-O antibonding orbitals, facilitating the destabilization of the peroxy bond for radical formation. Electronic structures of these precursors were compared, aiming to rationalize the tendency of the Φ values we observed. Overall, this time-resolved technique with specific probes can be used as a reliable tool to determine Φ , serving as a scientific basis for the accurate performance evaluation of diverse radical-based treatment processes.

One-step growth of Cu-doped carbon dots in amino-modified carbon nanotube-modified electrodes for sensitive electrochemical detection of BPA

Copper-doped carbon dots and aminated carbon nanotubes (Cu-CDs/NH2-CNTs) nanocomposites were synthesized by a one-step growth method, and the composites were characterized for their performance. An electrochemical sensor for sensitive detection of bisphenol A (BPA) was developed for using Cu-CDs/NH2-CNTs nanocomposites modified with glassy carbon electrodes (GCE). The sensor exhibited an excellent electrochemical response to BPA in 0.2 M PBS (pH 7.0) under optimally selected conditions. The linear range of the sensor for BPA detection was 0.5-160 μM, and the detection limit (S/N = 3) was 0.13 μM. Moreover, the sensor has good interference immunity, stability and reproducibility. In addition, the feasibility of the practical application of the sensor was demonstrated by the detection of BPA in bottled drinking water and Liu Yang River water.

The number of test organisms might influence the toxicity evaluation of hydrophobic micropollutants

Evaluating the toxicity of micropollutants forms the basis for understanding their potential risks to the ecosystem and/or human health. To accurately evaluate the toxicity of micropollutants in toxicity tests, many factors have been carefully considered, while the impact of the number of test organisms on toxicity results has rarely been taken into account. In this study, the role of the organism number on the developmental toxicity of five micropollutants was investigated using embryos of the marine polychaete Platynereis dumerilii. The toxicity of hydrophobic micropollutants was found to decrease significantly with increasing the number of embryos used in the test. A quantitative model was developed to better describe how the number of embryos affected developmental toxicity. The model showed a satisfactory fit to the raw data in all scenarios tested. The intrinsic half-maximal effective concentration EC50,int was then determined using the model. For a given compound, the EC50,int was a stable parameter that did not depend on the number of test embryos and thus provided an indication of the intrinsic toxicity of the compounds tested. Compared with the EC50 values determined with the commonly used embryo number (around 120), the EC50,int values of all tested hydrophobic micropollutants were lower. The more hydrophobic the compounds tested, the more pronounced the reduction in toxicity. This suggested that hydrophobic micropollutants could be more toxic than reported in the literature. Some suggestions were also made to eliminate the effect of the number of organisms used in the toxicity evaluation.

Health of wild fish exposed to contaminants of emerging concern in freshwater ecosystems utilized by a Minnesota Tribal community

Fish serve as indicators of exposure to contaminants of emerging concern (CECs)-chemicals such as pharmaceuticals, hormones, and personal care products-which are often designed to impact vertebrates. To investigate fish health and CECs in situ, we evaluated the health of wild fish exposed to CECs in waterbodies across northeastern Minnesota with varying anthropogenic pressures and CEC exposures: waterbodies with no human development along their shorelines, those with development, and those directly receiving treated wastewater effluent. Then, we compared three approaches to evaluate the health of fish exposed to CECs in their natural environment: a refined fish health assessment index, a histopathological index, and high-throughput (ToxCast) in vitro assays. Lastly, we mapped adverse outcome pathways (AOPs) associated with identified ToxCast assays to determine potential impacts across levels of biological organization within the aquatic system. These approaches were applied to subsistence fish collected from the Grand Portage Indian Reservation and 1854 Ceded Territory in 2017 and 2019. Overall, 24 CECs were detected in fish tissues, with all but one of the sites having at least one detection. The combined implementation of these tools revealed that subsistence fish exposed to CECs had histological and macroscopic tissue and organ abnormalities, although a direct causal link could not be established. The health of fish in undeveloped sites was as poor, or sometimes poorer, than fish in developed and wastewater effluent-impacted sites based on gross and histologic tissue lesions. Adverse outcome pathways revealed potential hazardous pathways of individual CECs to fish. A better understanding of how the health of wild fish harvested for consumption is affected by CECs may help prioritize risk management research efforts and can ultimately be used to guide fishery management and public health decisions. Integr Environ Assess Manag 2024;20:846-863. © 2023 The Authors. Integrated Environmental Assessment and Management published by Wiley Periodicals LLC on behalf of Society of Environmental Toxicology & Chemistry (SETAC).

A critical review of advances in tumor metabolism abnormalities induced by nitrosamine disinfection by-products in drinking water

Intensified sanitation practices amid the recent severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) outbreak might result in the increased release of chloramine disinfectants into surface water, significantly promoting the formation of nitrosamine disinfection by-products (DBPs) in drinking water. Unfortunately, these nitrosamine DBPs exhibit significant genotoxic, carcinogenic, and mutagenic properties, whereas chlorinating disinfectants remain in global practice. The current review provides valuable insights into the occurrence, identification, contamination status, exposure limits, and toxicity of the new unregulated disinfection by-products (nitrosamine DBPs) in drinking water. As a result, concentrations of nitrosamine DBPs far exceed allowable limits in drinking water, and prolonged exposure has the potential to cause metabolic disorders, a critical step in tumor initiation and progression. Importantly, based on recent research, we have concluded the role of nitrosamines DBPs in different metabolic pathways. Remarkably, nitrosamine DBPs can induce chronic inflammation and initiate tumors by activating sphingolipid and polyunsaturated fatty acid metabolism. Regarding amino acid and nucleotide metabolism, nitrosamine DBPs can inhibit tryptophan metabolism and de novo nucleotide synthesis. Moreover, inhibition of de novo nucleotide synthesis fails to repair DNA damage induced by nitrosamines. Additionally, the accumulation of lactate induced by nitrosamine DBPs may act as a pivotal signaling molecule in communication within the tumor microenvironment. However, with the advancement of tumor metabolomics, understanding the role of nitrosamine DBPs in causing cancer by inducing metabolic abnormalities significantly lags behind, and specific mechanisms of toxic effects are not clearly defined. Urgently, further studies exploring this promising area are needed.

Multifunctional Manganese-Nucleotide Laccase-Mimicking Nanozyme for Degradation of Organic Pollutants and Visual Assay of Epinephrine via Smartphone

As a natural green catalyst, laccase has extensive application in the fields of environmental monitoring and pollutant degradation. However, susceptibility to environmental influences and poor reusability seriously hinder its application. To address these concerns, for the first time, manganese ion replaced copper ion as the active center to coordinate with guanosine monophosphate (GMP) for synthesizing mimic laccase with high catalytic activity. Compared with natural laccase, the laccase-like nanozyme (Mn-GMPNS) demonstrated superior thermal stability, acid-base resistance, salt tolerance, reusability, and substrate universality. Benefiting from the high catalytic activity of Mn-GMPNS, epinephrine, a significant neurotransmitter and hormone associated with numerous diseases, was visually detected within 10 min and a portable assay by smartphone. More encouragingly, Mn-GMPNS can efficiently degrade dye pollutants, achieving a decolorization rate over 70% within 30 min. Thus, the coordination between manganese ion and nucleotide demonstrated the potential in rational design of nanozymes with high catalytic activity, low cost, good stability, and good biocompatibility.

Degradation of Chloroquine by Ammonia-Oxidizing Bacteria: Performance, Mechanisms, and Associated Impact on N2O Production

Since the mass production and extensive use of chloroquine (CLQ) would lead to its inevitable discharge, wastewater treatment plants (WWTPs) might play a key role in the management of CLQ. Despite the reported functional versatility of ammonia-oxidizing bacteria (AOB) that mediate the first step for biological nitrogen removal at WWTP (i.e., partial nitrification), their potential capability to degrade CLQ remains to be discovered. Therefore, with the enriched partial nitrification sludge, a series of dedicated batch tests were performed in this study to verify the performance and mechanisms of CLQ biodegradation under the ammonium conditions of mainstream wastewater. The results showed that AOB could degrade CLQ in the presence of ammonium oxidation activity, but the capability was limited by the amount of partial nitrification sludge (∼1.1 mg/L at a mixed liquor volatile suspended solids concentration of 200 mg/L). CLQ and its biodegradation products were found to have no significant effect on the ammonium oxidation activity of AOB while the latter would promote N2O production through the AOB denitrification pathway, especially at relatively low DO levels (≤0.5 mg-O2/L). This study provided valuable insights into a more comprehensive assessment of the fate of CLQ in the context of wastewater treatment.

Pharmacokinetic model of human exposure to ciprofloxacin through consumption of fish

Fluoroquinolones are broad-spectrum antibiotics that accumulate in the environment. To assess human exposure through the food chain, we developed a pharmacokinetic model of fluoroquinolone accumulation in fish and a human pharmacokinetic model to predict gastrointestinal concentrations of ciprofloxacin, a common fluoroquinolone, following consumption of fish. At 70 ng/L ciprofloxacin, the average in North American surface waters, the fish steady-state concentration was calculated to be 7.5 × 10-6 µg/g. Upon human consumption of the FDA-recommended portion of 113 g of fish containing this ciprofloxacin level, the predicted human intestinal concentration was 2 × 10-6 µg/mL. At 4 × 106 ng/L (4 µg/mL) ciprofloxacin, the highest recorded environmental measurement, these numbers were 0.42 µg/g in fish and 0.1 µg/mL in the human intestine. Thus, based on the ciprofloxacin MIC for E. coli of 0.13 µg/mL, background environmental ciprofloxacin levels are unlikely to be problematic, but environmental pollution can result in high intestinal levels that may cause gut dysbiosis and antibiotic resistance.

Sensors for Emerging Water Contaminants: Overcoming Roadblocks to Innovation

Ensuring water quality and safety requires the effective detection of emerging contaminants, which present significant risks to both human health and the environment. Field deployable low-cost sensors provide solutions to detect contaminants at their source and enable large-scale water quality monitoring and management. Unfortunately, the availability and utilization of such sensors remain limited. This Perspective examines current sensing technologies for detecting emerging contaminants and analyzes critical barriers, such as high costs, lack of reliability, difficulties in implementation in real-world settings, and lack of stakeholder involvement in sensor design. These technical and nontechnical barriers severely hinder progression from proof-of-concepts and negatively impact user experience factors such as ease-of-use and actionability using sensing data, ultimately affecting successful translation and widespread adoption of these technologies. We provide examples of specific sensing systems and explore key strategies to address the remaining scientific challenges that must be overcome to translate these technologies into the field such as improving sensitivity, selectivity, robustness, and performance in real-world water environments. Other critical aspects such as tailoring research to meet end-users' requirements, integrating cost considerations and consumer needs into the early prototype design, establishing standardized evaluation and validation protocols, fostering academia-industry collaborations, maximizing data value by establishing data sharing initiatives, and promoting workforce development are also discussed. The Perspective describes a set of guidelines for the development, translation, and implementation of water quality sensors to swiftly and accurately detect, analyze, track, and manage contamination.

A computational investigation of DMSO/water separation through functionalized GO multilayer nanosheet membrane using molecular dynamics simulation and deep neural network model for membrane performance prediction

In this molecular dynamics (MD) simulation study, the separation of dimethyl sulfoxide (DMSO) from water was investigated using multilayer functionalized graphene oxide (GO) membranes. The GO nanosheets were modified with chemical groups (-F, -H) to alter their properties. The study analyzed the influence of pressure and functional groups on the separation rate. Additionally, a deep neural network (DNN) model was developed to predict membrane behavior under different conditions in water treatment processes. Results revealed that the fluorine-functionalized membrane exhibited higher permeation compared to the hydrogen-functionalized one, with potential of mean force (PMF) analysis indicating higher energy barriers for water molecules passing through the hydrogen-functionalized membrane. The study used density profile, water density map analysis, and radial distribution function (RDF) analysis to understand water and DMSO molecule interactions. The diffusion coefficient of water molecules was also calculated, showing higher diffusion in the fluorine-functionalized system. Overall, the findings suggest that functionalized GO membranes are effective for DMSO-water separation, with the fluorine-functionalized membrane showing superior performance. The DNN model accurately predicts membrane behavior, contributing to the optimization of membrane separation systems.

ChloroDBPFinder: Machine Learning-Guided Recognition of Chlorinated Disinfection Byproducts from Nontargeted LC-HRMS Analysis

High-resolution mass spectrometry (HRMS) is a prominent analytical tool that characterizes chlorinated disinfection byproducts (Cl-DBPs) in an unbiased manner. Due to the diversity of chemicals, complex background signals, and the inherent analytical fluctuations of HRMS, conventional isotopic pattern (37Cl/35Cl), mass defect, and direct molecular formula (MF) prediction are insufficient for accurate recognition of the diverse Cl-DBPs in real environmental samples. This work proposes a novel strategy to recognize Cl-containing chemicals based on machine learning. Our hierarchical machine learning framework has two random forest-based models: the first layer is a binary classifier to recognize Cl-containing chemicals, and the second layer is a multiclass classifier to annotate the number of Cl present. This model was trained using ∼1.4 million distinctive MFs from PubChem. Evaluated on over 14,000 unique MFs from NIST20, this machine learning model achieved 93.3% accuracy in recognizing Cl-containing MFs (Cl-MFs) and 92.9% accuracy in annotating the number of Cl for Cl-MFs. Furthermore, the trained model was integrated into ChloroDBPFinder, a standalone R package for the streamlined processing of LC-HRMS data and annotating both known and unknown Cl-containing compounds. Tested on existing Cl-DBP data sets related to aspartame chlorination in tap water, our ChloroDBPFinder efficiently extracted 159 Cl-containing DBP features and tentatively annotated the structures of 10 Cl-DBPs via molecular networking. In another application of a chlorinated humic substance, ChloroDBPFinder extracted 79 high-quality Cl-DBPs and tentatively annotated six compounds. In summary, our proposed machine learning strategy and the developed ChloroDBPFinder provide an advanced solution to identifying Cl-containing compounds in nontargeted analysis of water samples. It is freely available on GitHub (https://github.com/HuanLab/ChloroDBPFinder).

Transformation products of antibacterial drugs in environmental water: Identification approaches based on liquid chromatography-high resolution mass spectrometry

In recent years, the presence of antibiotics in the aquatic environment has caused increasing concern for the possible consequences on human health and ecosystems, including the development of antibiotic-resistant bacteria. However, once antibiotics enter the environment, mainly through hospital and municipal discharges and the effluents of wastewater treatment plants, they can be subject to transformation reactions, driven by both biotic (e.g. microorganism and mammalian metabolisms) and abiotic factors (e.g. oxidation, photodegradation, and hydrolysis). The resulting transformation products (TPs) can be less or more active than their parent compounds, therefore the inclusion of TPs in monitoring programs should be mandatory. However, only the reference standards of a few known TPs are available, whereas many other TPs are still unknown, due to the high diversity of possible transformation reactions in the environment. Modern high-resolution mass spectrometry (HRMS) instrumentation is now ready to tackle this problem through suspect and untargeted screening approaches. However, for handling the large amount of data typically encountered in the analysis of environmental samples, these approaches also require suitable processing workflows and accurate tandem mass spectra interpretation. The compilation of a suspect list containing the possible monoisotopic masses of TPs retrieved from the literature and/or from laboratory simulated degradation experiments showed unique advantages. However, the employment of in silico prediction tools could improve the identification reliability. In this review, the most recent strategies relying on liquid chromatography-HRMS for the analysis of environmental TPs of the main antibiotic classes were examined, whereas TPs formed during water treatments or disinfection were not included.

Theoretical studies on the photo protective mechanism of curcuminoids

In this work, the deactivation pathways of curcuminoids after photoexcitation was studied by employing density functional theory to explore their UVA radiation screening capacity. A comprehensive computational characterization of the excited-state processes of curcumin, demethoxycurcumin, and bis-demethoxycurcumin was done. The molecules exist in diketo and enol forms which are in equilibrium and interconvertible through keto-enol tautomerism. The enolic forms of each of the studied molecules have eight geometric cis-trans isomers as a result of torsion rotation about three different carbon-carbon double bonds across the aliphatic chain. For each geometric isomer, sixteen possible rotamers are found to exist due to rotation about five different carbon-carbon single bond rotations, also across the skeleton of the aliphatic chain. Upon photoexcitation, the studied molecules follow three main pathways of radiationless decay: (a) rotamerism and interconversion between rotamers of comparable energies which are in equilibrium, (b) interconversion between the cis-trans geometrical isomers where an efficient vibrational relaxation path is formed at ∼90° during torsion rotation about carbon-carbon double bond, and (c) excited state intramolecular proton transfer in a single O-H stretching vibration through a cyclic intramolecular hydrogen bonded ring formed at the centre of the molecule giving back the original structure. The absorption and emission spectra of the molecules were also simulated where the theoretically obtained absorption and emission maxima are close to the reported experimental values.

Database and review of disinfection by-products since 1974: Constituent elements, molecular weights, and structures

Since trihalomethanes were discovered in 1974, disinfection by-products (DBPs) in drinking water have attracted extensive attention. In 2011, more than 600 known DBPs were compiled; however, newly reported DBPs have not been integrated. The rapid development of mass spectrometry has led to a significant increase in the number of DBPs, therefore, there is a need to develop a database of all DBPs and their properties. Herein, a database including 6310 DBPs (651 confirmed, 1478 identified and 4142 proposed) reported between 1974 and 2022 was constructed and made available for public use at https://dbps.com.cn/main. This database can be a tool in screening new DBPs, comprehensively reviewing, and developing predictive models. In this paper, to demonstrate the functions of the database and provide useful information for this area, the origin of the collected DBPs was presented, and some basic information, including elemental composition, molecular weight, functional groups, and carbon frameworks, were comparatively analyzed. The results showed that the proportion of DBPs verified by standard compounds and frequently detected in real water is less than 7.0%, and most of DBPs remained to be identified. Approximately 88% of DBPs contain halogens, and brominated -DBPs occupied a similar ratio to chlorinated -DBPs in real water. Acids were the main functional groups of DBPs, aliphatic and aromatic compounds are the two major carbon frameworks, and the molecular weights of most DBPs ranged from 200 to 400 Da. In addition, 4142 proposed DBPs as obtained using high-resolution mass spectrometry, were characterized based on the modified van Krevelen diagram and adjusted indexes with halogens. Most of the proposed DBPs featured lignin and tannin structures, and phenolic/highly unsaturated DBPs account for the majority.

Risks of obstructive genitourinary birth defects in relation to trihalomethane and haloacetic acid exposures: expanding disinfection byproduct mixtures analyses using relative potency factors

BACKGROUND

Some disinfection byproducts (DBPs) are teratogens based on toxicological evidence. Conventional use of predominant DBPs as proxies for complex mixtures may result in decreased ability to detect associations in epidemiological studies.

OBJECTIVE

We assessed risks of obstructive genitourinary birth defects (OGDs) in relation to 12 DBP mixtures and 13 individual component DBPs.

METHODS

We designed a nested registry-based case-control study (210 OGD cases; 2100 controls) in Massachusetts towns with complete quarterly 1999-2004 data on four trihalomethanes (THMs) and five haloacetic acids (HAAs). We estimated temporally-weighted average DBP exposures for the first trimester of pregnancy. We estimated adjusted odds ratios (aORs) and 95% confidence intervals (CIs) for OGD in relation to individual DBPs, unweighted mixtures, and weighted mixtures based on THM/HAA relative potency factors (RPF) from animal toxicology data for full-litter resorption, eye defects, and neural tube defects.

RESULTS

We detected elevated aORs for OGDs for the highest of bromodichloromethane (aOR = 1.75; 95% CI: 1.15-2.65), dibromochloromethane (aOR = 1.71; 95% CI: 1.15-2.54), bromodichloroacetic acid (aOR = 1.56; 95%CI: 0.97-2.51), chlorodibromoacetic acid (aOR = 1.97, 95% CI: 1.23-3.15), and tribromoacetic acid (aOR = 1.90; 95%CI: 1.20-3.03). Across unweighted mixture sums, the highest aORs were for the sum of three brominated THMs (aOR = 1.74; 95% CI: 1.15-2.64), the sum of six brominated HAAs (aOR = 1.43; 95% CI: 0.89-2.31), and the sum of nine brominated DBPs (aOR = 1.80; 95% CI: 1.05-3.10). Comparing eight RPF-weighted to unweighted mixtures, the largest aOR differences were for two HAA metrics, which both were higher with RPF weighting; other metrics had reduced or minimally changed ORs in RPF-weighted models.

Magnetic nanocellulose-based adsorbent for highly selective removal of malachite green from mixed dye solution

Herein, a novel magnetic adsorbent (BC/AA/MN@Fe3O4) was successfully prepared from waste bamboo fiber tissue and montmorillonite, and subsequently applied for the highly selective removal of malachite green (MG, removal efficiency = 97.3 %) from the mixed dye solution of MG with methyl orange (MO, removal efficiency = 4.5 %). The magnetic adsorbent has a high porosity with abundant mesopores. In the single dye MG solution, the adsorbent could effectively remove MG over a wide pH range from 4 to 10, and the maximum adsorption capacity (qmax) was 2282.3 mg/g. Moreover, the magnetic adsorbent could remove MG from various solutions including mixed dye solution, high salinity solution, and real river water dye solution. The thermodynamic results proved that the adsorption process of MG was spontaneous and endothermic. The adsorption of MG was due to the comprehensive effects of electrostatic attraction, hydrogen bonding interactions and ions exchange, between the adsorbent and MG. Furthermore, the BC/AA/MN@Fe3O4 exhibited an excellent reusability with adsorption efficiency above 53.4 % after five consecutive cycles. Therefore, the prepared magnetic nanocellulose-based adsorbent was expected to be a promising material for highly selective adsorption and separation of MG from mixed dye solution.

Total organic halogen (TOX) in drinking water: Occurrence, correlation analysis, and precursor removal during drinking water treatment

Total organic halogen (TOX) in drinking water provides a measurement of the overall organic halogenated disinfection by-products (DBPs) formed during disinfection. Yangtze River Delta is one of the regions with the highest population density, the fastest urbanization process, and the most severe water pollution in China. Collecting water samples from full-scale drinking water treatment plants (DWTPs) in this region, this study firstly surveyed TOX occurrence in drinking water. Besides, the correlation of TOX formation potential (TOXFP) and trihalomethane formation potential (THMFP) with general water quality parameters (e.g., dissolved organic carbon [DOC], UV254, and specific ultraviolet absorbance) and the removal efficiencies of TOX precursors by different water treatment processes were also investigated. TOX levels in DWTP effluents (i.e., finished water) ranged from 29 to 165 μg/L (median 67 μg/L), and those in simulated distribution system waters ranged from 101 to 276 μg/L (median 158 μg/L). There were generally higher linear regression coefficient values for raw water (R2 = 0.51-0.88) than for treated water (R2 = 0.33-0.64) in terms of the relationship between DBP formation potentials and general parameters. However, a relatively stronger correlation between THMFP and TOXFP was observed for treated water (R2 = 0.80, p < 0.001) than for raw water (R2 = 0.64, p < 0.001). The overall treatment efficiencies of investigated parameters in DWTPs generally followed the order of UV254 > DOC > TOX precursors > THM precursors. Notably, the overall removal rates of DOC and TOX precursors in summer (averaging 59 % and 54 %, respectively) were obviously higher than those in winter (averaging 39 % and 38 %, respectively), which was assumed to be related to the seasonal variation of bioactivity in sand filter. These results could expand the knowledge of TOX in drinking water, and provide valuable perspectives to water industry and DBP research.

Trihalomethanes in developed and developing countries

The reactions between natural organic matter, anthropogenic contaminants, ions, and disinfectants lead to the formation of disinfection by-products (DBPs) such as trihalomethanes (THMs) in drinking water. The formation of THMs is strongly related to the chlorination of water. The study's central objective was to compare the concentration of THMs in twenty developed and developing countries and their disinfection techniques. The THM concentration in 11 developed and 9 developing countries ranged from 0.5 µg/L (Germany) to 215 µg/L (Russia) and 3 µg/L (China) to 439.2 µg/L (Bangladesh), respectively. The developed country has partially succeeded in reducing THM concentration in drinking water, whereas significant steps are needed in developing countries to reduce the existing high THM concentration. The concentration of THMs in water varies among these countries because of the different water sources, water quality, environmental conditions, and efficiency of water treatment technologies. A meaningful relationship has been observed between the properties of water and the THM formation. The use of chemical disinfectants will result in new forms of DBPs that are undesirable due to their carcinogenic and mutagenic effects on human health. The DBP guidelines by various national and international agencies have helped to control and manage the THM concentration in drinking water. However, these regulatory standards are not continuously monitored. Therefore, the formation of these compounds should be prevented either by removing THMs forming precursors or by using an integrated approach for controlling THM formation by implementing advanced water treatment technology. Extensive research is desirable in domains like THM minimization strategies which are easy to deploy, scalable, and cost-effective.

Reconnaissance Survey of Organic Contaminants of Emerging Concern in the Kabul and Swat Rivers of Pakistan

The Swat and Kabul rivers of northern Pakistan are within an important regional watershed that supports river-based livelihoods and is impacted by untreated effluent discharges and municipal solid waste. Evidence indicates that fish populations are decreasing in these rivers. One potential cause of poor aquatic health is pollution; therefore, we investigated the presence of contaminants of emerging concern (CECs) in the river systems. Water samples were collected in the Kabul River (n = 9) and Swat River (n = 10) during seasons of high (summer 2018) and low (winter 2019) river flow. Agrochemicals, pharmaceuticals, plasticizers, chemicals in personal care products, and hormones were quantified via liquid chromatography high-resolution mass spectrometry. In the Swat River, caffeine (18-8452 ng/L), N,N-diethyl-meta-toluamide (DEET; 16-56 ng/L), and plasticizers (13-7379 ng/L) were detected at all sites during both seasons, while butachlor (16-98 ng/L) was detected only during high flow. In the Kabul River, caffeine (12-2081 ng/L) and several plasticizers (91-722 ng/L) were detected at all sites during both seasons, while DEET (up to 97 ng/L) was detected only during high flow. During low flow, pharmaceuticals (analgesics and nonsteroidal anti-inflammatory drugs) were quantified in both rivers (up to 823 ng/L), with detection frequencies from 70% to 100% and 0% to 78% in the Swat and Kabul Rivers, respectively. Intermittent-use and natural seasonal processes (increased runoff and dilution from rainfall and snowmelt) yielded higher agrochemical concentrations and lower concentrations of continuous-use compounds (e.g., caffeine) during high flow. The present study provides the first insight into CEC concentrations in the Swat River, additional insight into the Kabul River stressors, and, overall, contaminant risks to aquatic life. Environ Toxicol Chem 2023;42:2599-2613. © 2023 The Authors. Environmental Toxicology and Chemistry published by Wiley Periodicals LLC on behalf of SETAC.

Differences in the degradation behavior of disinfection by-products in UV/PDS and UV/H2O2 processes and the effect of their chemical properties

In this work, sixteen typical chlorinated and brominated aromatic disinfection by-products (DBPs) were selected as examples to investigate their different degradation mechanisms initiated by HO• and SO4•-. Addition reactions were the main mode of degradation of DBPs by HO•, while SO4•- dominated H-abstraction reactions and single electron transfer reactions. Chlorinated compounds had higher reactivity than brominated compounds. Furthermore, substituents with stronger electron-donating effects promoted the electrophilic reaction of DBPs with the two radicals. In addition, we developed a model based on the chemical properties LUMO, fmax-, and hardness for predicting the average reaction energy barriers for the initial reactions of DBPs with HO• and SO4•-. The model had good predictive performance for the difficulty of degradation of different DPBs by HO• and SO4•-, with R2 values of 0.85 and 0.87, respectively. Through the degradation efficiency simulation, we found that longer reaction times, higher oxidant concentrations and lower pollutant concentrations were more favorable for the removal of DBPs. The UV/PDS process showed better degradation of DBPs than the UV/H2O2 process. In addition, most degradation products of DBPs exhibited less toxicity to aquatic organisms than their parent compounds. This study provided theoretical guidance for the degradation and removal of other aromatic DBPs at the molecular level.

Unravelling High-Molecular-Weight DBP Toxicity Drivers in Chlorinated and Chloraminated Drinking Water: Effect-Directed Analysis of Molecular Weight Fractions

As disinfection byproducts (DBPs) are ubiquitous sources of chemical exposure in disinfected drinking water, identifying unknown DBPs, especially unknown drivers of toxicity, is one of the major challenges in the safe supply of drinking water. While >700 low-molecular-weight DBPs have been identified, the molecular composition of high-molecular-weight DBPs remains poorly understood. Moreover, due to the absence of chemical standards for most DBPs, it is difficult to assess toxicity contributions for new DBPs identified. Based on effect-directed analysis, this study combined predictive cytotoxicity and quantitative genotoxicity analyses and Fourier transform ion cyclotron resonance mass spectrometry (21 T FT-ICR-MS) identification to resolve molecular weight fractions that induce toxicity in chloraminated and chlorinated drinking waters, along with the molecular composition of these DBP drivers. Fractionation using ultrafiltration membranes allowed the investigation of <1 kD, 1-3 kD, 3-5 kD, and >5 kD molecular weight fractions. Thiol reactivity based predictive cytotoxicity and single-cell gel electrophoresis based genotoxicity assays revealed that the <1 kD fraction for both chloraminated and chlorinated waters exhibited the highest levels of predictive cytotoxicity and direct genotoxicity. The <1 kD target fraction was used for subsequent molecular composition identification. Ultrahigh-resolution MS identified singly charged species (as evidenced by the 1 Da spacing in 13C isotopologues), including 3599 chlorine-containing DBPs in the <1 kD fraction with the empirical formulas CHOCl, CHOCl2, and CHOCl3, with a relative abundance order of CHOCl > CHOCl2 ≫ CHOCl3. Interestingly, more high-molecular-weight CHOCl1-3 DBPs were identified in the chloraminated vs chlorinated waters. This may be due to slower reactions of NH2Cl. Most of the DBPs formed in chloraminated waters were composed of high-molecular-weight Cl-DBPs (up to 1 kD) rather than known low-molecular-weight DBPs. Moreover, with the increase of chlorine number in the high-molecular-weight DBPs detected, the O/C ratio exhibited an increasing trend, while the modified aromaticity index (AImod) showed an opposite trend. In drinking water treatment processes, the removal of natural organic matter fractions with high O/C ratio and high AImod value should be strengthened to minimize the formation of known and unknown DBPs.

Co-Occurrence of Bromine and Iodine Species in US Drinking Water Sources That Can Impact Disinfection Byproduct Formation

Bromine and iodine species are precursors for forming disinfection byproducts in finished drinking waters. Our study incorporates spatial and temporal data to quantify concentrations of inorganic (bromide (Br-), iodide (I-), and iodate (IO3-)), organic, and total bromine (BrT) and iodine (IT) species from 286 drinking water sources and 7 wastewater effluents across the United States. Br- ranged from <5-7800 μg/L (median of 62 μg/L in surface water (SW) and 95 μg/L in groundwater (GW)). I- was detected in 41% of SW (1-72 μg/L, median = <1 μg/L) and 62% of GW (<1-250 μg/L, median = 3 μg/L) samples. The median Br-/I- ratio in SW and GW was 22 μg/μg and 16 μg/μg, respectively, in paired samples with detect Br- and I-. BrT existed primarily as Br-, while IT was present as I-, IO3-, and/or total organic iodine (TOI). Inorganic iodine species (I- and IO3-) were predominant in GW samples, accounting for 60-100% of IT; however, they contributed to only 20-50% of IT in SW samples. The unknown fraction of IT was attributed to TOI. In lakes, seasonal cycling of I-species was observed and was presumably due to algal productivity. Finally, Spearman Rank Correlation tests revealed a strong correlation between Br- and IT in SW (RBr-,IT = 0.83) following the log10 (Br-, μg/L) = 0.65 × log10 (IT, μg/L) - 0.17 relationship. Br- and I- in treated wastewater effluents (median Br- = 234 μg/L, median I- = 5 μg/L) were higher than drinking water sources.

Thiol Reactome: A Nontargeted Strategy to Precisely Identify Thiol Reactive Drinking Water Disinfection Byproducts

The precise identification of predominant toxic disinfection byproducts (DBPs) from disinfected water is a longstanding challenge. We propose a new acellular analytical strategy, the 'Thiol Reactome', to identify thiol-reactive DBPs by employing a thiol probe and nontargeted mass spectrometry (MS) analysis. Disinfected/oxidized water samples had reduced cellular oxidative stress responses of 46 ± 23% in Nrf2 reporter cells when preincubated with glutathione (GSH). This supports thiol-reactive DBPs as the predominant drivers of oxidative stress. This method was benchmarked using seven classes of DBPs including haloacetonitriles, which preferentially reacted with GSH via substitution or addition depending on the number of halogens present. The method was then applied to chemically disinfected/oxidized waters, and 181 tentative DBP-GSH reaction products were detected. The formulas of 24 high abundance DBP-GSH adducts were predicted, among which nitrogenous-DBPs (11) and unsaturated carbonyls (4) were the predominant compound classes. Two major unsaturated carbonyl-GSH adducts, GSH-acrolein and GSH-acrylic acid, were confirmed by their authentic standards. These two adducts were unexpectedly formed from larger native DBPs when reacting with GSH. This study demonstrated the "Thiol Reactome" as an effective acellular assay to precisely identify and broadly capture toxic DBPs from water mixtures.

Contributions of Pharmaceuticals to DBP Formation and Developmental Toxicity in Chlorination of NOM-containing Source Water

Pharmaceuticals have been considered a priority group of emerging micropollutants in source waters in recent years, while their role in the formation and toxicity of disinfection byproducts (DBPs) during chlorine disinfection remains largely unclear. In this study, the contributions of natural organic matter (NOM) and pharmaceuticals (a mixture of ten representative pharmaceuticals) to the overall DBP formation and toxicity during drinking water chlorination were investigated. By innovatively "normalizing" chlorine exposure and constructing a kinetic model, we were able to differentiate and evaluate the contributions of NOM and pharmaceuticals to the total organic halogen (TOX) formation for source waters that contained different levels of pharmaceuticals. It was found that at a chlorine contact time of 1.0 h, NOM (2 mg/L as C) and pharmaceuticals (total 0.0062-0.31 mg/L as C) contributed 79.8-99.5% and 0.5-20.2%, respectively, of TOX. The toxicity test results showed that the chlorination remarkably increased the toxicity of the pharmaceutical mixture by converting the parent compounds into more toxic pharmaceutical-derived DBPs, and these DBPs might contribute significantly to the overall developmental toxicity of chlorinated waters. This study highlights the non-negligible role of pharmaceuticals in the formation and toxicity of overall DBPs in chlorinated drinking water.

Recent progress in identification of water disinfection byproducts and opportunities for future research

Numerous disinfection by-products (DBPs) are formed from reactions between disinfectants and organic/inorganic matter during water disinfection. More than seven hundred DBPs that have been identified in disinfected water, only a fraction of which are regulated by drinking water guidelines, including trihalomethanes, haloacetic acids, bromate, and chlorite. Toxicity assessments have demonstrated that the identified DBPs cannot fully explain the overall toxicity of disinfected water; therefore, the identification of unknown DBPs is an important prerequisite to obtain insights for understanding the adverse effects of drinking water disinfection. Herein, we review the progress in identification of unknown DBPs in the recent five years with classifications of halogenated or nonhalogenated, aliphatic or aromatic, followed by specific halogen groups. The concentration and toxicity data of newly identified DBPs are also included. According to the current advances and existing shortcomings, we envisioned future perspectives in this field.

Microalgal-based bioremediation of emerging contaminants: Mechanisms and challenges

Emerging contaminants (ECs) in different ecosystems have consistently been acknowledged as a global issue due to toxicity, human health implications, and potential role in generating and disseminating antimicrobial resistance. The existing wastewater treatment system is incompetent at eliminating ECs since the effluent water contains significant concentrations of ECs, viz., antibiotics (0.03-13.0 μg L-1), paracetamol (50 μg L-1), and many others in varying concentrations. Microalgae are considered as a prospective and sustainable candidate for mitigating of ECs owing to some peculiar features. In addition, the microalgal-based processes also offer cost and energy-efficient solutions for the bioremediation of ECs than conventional treatment systems. It is pertinent that, microalgal-based processes also provides waste valorization benefits as microalgal biomass obtained after ECs treatment can be potentially applied to generate biofuels. Moreover, microalgae can effectively utilize alternative metabolic (cometabolism) routes for enhanced degradation of ECs. Additionally, the ECs removal via the microalgal biodegradation route is highly promising as it can transform the ECs into less toxic compounds. The present review comprehensively discusses different mechanisms involved in removing ECs and various factors that affect their removal. Also, the technoeconomic feasibility of microalgae than other conventional wastewater treatment methods is summarised. The review also highlighted the different molecular and genetic tools that can augment the activity and robustness of microalgae for better removal of organic contaminants. Finally, we have summarised the challenges and future research required towards microalgal-based bioremediation of emerging contaminants (ECs) as a holistic approach.

Characterization of halogenated organic compounds by the Fourier transform ion cyclotron resonance mass spectrometry: A critical review

Halogenated organic compounds (HOCs), widely present in various environments, are generally formed by natural processes (e.g., photochemical halogenation) and anthropogenic activities (e.g., water disinfection and anthropogenic discharge of HOCs), posing health and environmental risks. Therefore, in-depth knowledge of the molecular composition, transformation, and fate of HOCs is crucial to regulate and reduce their formation. Because of the extremely complex nature of HOCs and their precursors, the molecular composition of HOCs remains largely unknown. The Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS) offers the most powerful resolution and mass accuracy for the simultaneous molecular-level characterization of HOCs and their precursors. However, there is still a paucity of reviews regarding the comprehensive characterization of HOCs by FT-ICR MS. Based on the FT-ICR MS, the formation mechanism, sample pretreatment, and analysis methods were summarized for two typical HOCs classes, namely halogenated disinfection byproducts and per- and polyfluoroalkyl substances in this review. Moreover, we have highlighted data analysis methods and some typical applications of HOCs using FT-ICR MS and proposed suggestions for current issues. This review will deepen our understanding of the chemical characterization of HOCs and their formation mechanisms and transformation at the molecular level in aquatic systems, facilitating the application of the state-of-the-art FT-ICR MS in environmental and geochemical research.

Sustainable removal of phenol from wastewater using a biopolymer hydrogel adsorbent comprising crosslinked chitosan and κ-carrageenan

A biopolymer-based adsorbent comprising chitosan (CS) and κ-carrageenan (κ-Carr) was synthesised and evaluated to treat phenolic-contaminated water. The developed CS/κ-Carr hydrogel demonstrated excellent performance with a phenol adsorption uptake of 80 %. The morphologies of CS/κ-Carr hydrogels with different ratios of CS to κ-Carr ranging from 1:2 to 7:3 were characterised using scanning electron microscopy and atomic force microscopy; their chemical structures were investigated by spectral analyses using Fourier-transform infrared spectroscopy, thermogravimetric analysis, and differential scanning calorimetry; their adsorption characteristics were determined using tests for swelling, chemical stability, hygroscopic moisture content, and hydrophilicity. Finally, a batch-type evaluation method demonstrated adsorption performance at 25 °C and pH 6.9. Adsorption isotherms and kinetic data were successfully obtained using the Freundlich and pseudo-second-order models, respectively. The results indicate that one-pot synthesis of an insoluble CS/κ-Carr hydrogel adsorbent exhibits considerable potential for the removal of phenol from aqueous solutions, providing an environmentally friendly technology enhancing the phenol adsorption performance of CS.

Occurrence, stability and cytotoxicity of halobenzamides: A new group of nitrogenous disinfection byproducts in drinking water

Exploring disinfection byproducts (DBPs) with adverse health effects in drinking water is a constant challenge. Halobenzamides (HBZAMs) are suspected to be a new group of nitrogenous DBPs but have not been reported in drinking water to date. In this study, by coupling SPE and UPLC‒MS/MS, a sensitive method was established to detect eight HBZAMs in drinking water with recoveries and limits of detection of 80-103% and 0.01-0.04 ng/L, respectively. Subsequently, distinct fragments of HBZAMs were extended to the development of a pseudotargeted method for the analysis of the fourteen HBZAMs that were speculated and lack chemical standards. Using the developed method, eight HBZAMs were quantified in ten drinking water samples with concentrations ranging from 2.4 to 7.2 ng/L and a detection frequency of 100%, among which five HBZAMs were stable with half-lives over 72 h under real chlorine levels. Twelve HBZAMs without standards were identified in three to ten drinking water samples with comparable levels. The cytotoxicity of eight quantified HBZAMs in CHO-K1 cells varied with disparity, in which the cytotoxicity of 3,5-DBBZAM was over 10-fold higher than that of aliphatic dichloroacetamide. Considering their diversity, toxicity and stability, the occurrence of HBZAMs in drinking water deserves attention.

Immunotechniques for the Group Determination of Macrolide Antibiotics Traces in the Environment Using a Volume-Mediated Sensitivity Enhancement Strategy

Macrolide antibiotics, which are effective antimicrobial agents, are intensively used in human and veterinary medicine, as well as in agriculture. Consequently, they are found all over the world as environmental pollutants, causing harm to sensitive ecological communities and provoking a selection of resistant forms. A novel azithromycin derivative, which was used as hapten conjugate, ensured the group immunorecognition of six major macrolide representatives (105-41%), namely erythromycin, erythromycin ethylsuccinate, clarithromycin, roxithromycin, azithromycin, and dirithromycin in a competitive immunoassay based on anti-clarithromycin antibodies. The heterologous hapten-based ELISA format resulted in a 5-fold increase in sensitivity, with an IC50 value of 0.04 ng/mL for erythromycin. In this study, we proposed an underexploited strategy in an immunoassay field to significantly improve the detectability of analytes in environmental samples. Unlike most approaches, it does not require special enhancers/amplifiers or additional concentration/extraction procedures; instead, it involves analyzing a larger volume of test samples. A gradual volume increase in the samples (from 0.025 to 10 mL) analyzed using a direct competitive ELISA, immunobeads, and immunofiltration assay formats based on the same reagents resulted in a significant improvement (more than 50-fold) in assay sensitivity and detection limit up to 5 and 1 pg/mL, respectively. The suitability of the test for detecting the macrolide contamination of natural water was confirmed by the recovery of macrolides from spiked blank samples (71.7-141.3%). During 2022-2023, a series of natural water samples from Lake Onega and its influents near Petrozavodsk were analyzed, using both the developed immunoassay and HPLC-MS/MS. The results revealed no contamination of macrolide antibiotic.

Enhanced removal of antibiotic and antibiotic resistance genes by coupling biofilm electrode reactor and manganese ore substrate up-flow microbial fuel cell constructed wetland system

Manganese ore substrate up-flow microbial fuel cell constructed wetland (UCW-MFC(Mn)) as an innovative wastewater treatment technology for purifying antibiotics and electricity generation with few antibiotic resistance genes (ARGs) generation has attracted attention. However, antibiotic purifying effects should be further enhanced. In this study, a biofilm electrode reactor (BER) that needs direct current driving was powered by a Mn ore anode (UCW-MFC(Mn)) to form a coupled system without requiring direct-current source. Removal efficiencies of sulfadiazine (SDZ), ciprofloxacin (CIP) and the corresponding ARGs in the coupled system were compared with composite (BER was powered by direct-current source) and anaerobic systems (both of BER and UCW-MFC were in open circuit mode). The result showed that higher antibiotic removal efficiency (94% for SDZ and 99.1% for CIP) in the coupled system was achieved than the anaerobic system (88.5% for SDZ and 98.2% for CIP). Moreover, electrical stimulation reduced antibiotic selective pressure and horizontal gene transfer potential in BER, and UCW-MFC further reduced ARG abundances by strengthening the electro-adsorption of ARG hosts determined by Network analysis. Bacterial community diversity continuously decreased in BER while it increased in UCW-MFC, indicating that BER mitigated the toxicity of antibiotic. Degree of modularity, some functional bacteria (antibiotic degrading bacteria, fermentative bacteria and EAB), and P450 enzyme related to antibiotic and xenobiotics biodegradation genes were enriched in electric field existing UCW-MFC, accounting for the higher degradation efficiency. In conclusion, this study provided an effective strategy for removing antibiotics and ARGs in wastewater by operating a BER-UCW-MFC coupled system.

Revealing the factors resulting in incomplete recovery of perfluoroalkyl acids (PFAAs) when implementing the adsorbable and extractable organic fluorine methods

Per- and polyfluoroalkyl substances (PFASs) are environmental contaminants of concern. Techniques that quantify total organic fluorine (TOF) such as the adsorbable organic fluorine (AOF) and extractable organic fluorine (EOF) methods are important for PFAS risk assessments. The objective of this study was to systematically evaluate each step of the AOF (loading, washing, combustion) and EOF (loading, washing, elution, combustion) methods for the recovery of ten ultrashort-, short-, and long-chain unsubstituted perfluoroalkyl acids (PFAAs). We measured the overall recovery of fluoride for each method for each PFAA, and the recovery of each PFAA around the loading, washing, and elution steps. We also measured the combustion efficiency of each PFAA by direct combustion. The overall AOF and EOF recovery ranged from 9.3%-103.3% to 21.0%-108.1%, respectively, with higher recoveries measured for PFAAs with increasing chain length in both methods. The three ultrashort-chain PFAAs (trifluoroacetic acid, perfluoropropionic acid, and perfluoropropanesulfonic acid) exhibited the lowest overall recoveries from 9.3-25.2% for AOF and 21.0-51.5% for EOF. We found that decreases in the overall recovery are the result of losses of ultrashort- and short-chain PFAAs during the washing step and the incomplete mineralization of perfluoroalkyl sulfonic acids during combustion for AOF and incomplete elution of short- and long-chain PFAAs and the loss of ultrashort-chain PFAAs during the washing step for EOF. Our data suggest that the EOF method is more appropriate than the AOF method for measuring TOF in samples containing ultrashort- and short-chain PFAAs and that methodological improvements are possible with a focus on the washing, elution, and combustion steps.

Toxicity evolution and control for the UV/H2O2 degradation of nitrogen-containing heterocyclic compounds: SDZ and PMM

This study aimed to achieve toxicity control of sulfadiazine (SDZ) and pirimiphos-methyl (PMM) via the UV/H2O2 process by optimizing the reaction parameters. The results show that both drugs had a good degradation effect under the following parameters: a H2O2 molar ratio of 1:200, and neutral conditions. SDZ and PMM could be degraded by more than 99% within 3 min, respectively. In the Daphnia magna acute toxicity assay and Vibrio fischeri inhibition assay, both SDZ and PMM exhibited a phenomenon of increasing toxicity. Additionally, through the use of density functional theory (DFT) calculation and HPLC-QTOF-MS, 21 transformation products (TPs) were identified, and the principal degradation pathways were proposed. The toxicity of the TPs was determined by comparing the QSAR prediction results with toxicity test data. As a result, under the higher UV light intensity (2300 μW/cm2) and neutral conditions, SDZ showed highest toxicity, whereas PMM showed lowest toxicity under the lowest UV light intensity (450 μW/cm2) and neutral conditions. Four main toxic TPs were identified, and their yields could be reduced by adjusting the reaction parameters. Therefore, the selection of appropriate reaction parameters could reduce the production of toxic TPs and ensure the safety of water environment.

A review of electro-Fenton and ultrasound processes: towards a novel integrated technology for wastewater treatment

Nowadays, the presence of persistent dissolved pollutants in water has received increasing attention due to their toxic effects on living organisms. Considering the limitations of conventional wastewater treatment processes for the degradation of these compounds, advanced oxidation processes such as electro-Fenton and sono-chemical process, as well as their combination, appear as potentially effective options for the treatment of wastewater contaminated with bio-recalcitrant pollutants. In view of the importance of the development of processes using real effluents, this review aims to provide a comprehensive perspective of sono-electro-Fenton-related processes applied for real wastewater treatment. In the first section, the fundamentals and effectiveness of both homogeneous and heterogeneous electro-Fenton approaches for the treatment of real wastewater are presented. While the second part of this work describes the fundamentals of ultrasound-based processes, the last section focuses on the coupling of the two methods for real wastewater treatment and on the effect of the main operational parameters of the process. On the basis of the information presented, it is suggested that sono-electro-Fenton processes substantially increase the efficiency of the treatment as well as the biodegradability of the treated wastewater. The combined effect results from mass transfer improvement, electrode cleaning and activation, water electrolysis, and the electro-Fenton-induced production of hydroxyl radicals. The information presented in this work is expected to be useful for closing the gap between laboratory-scale assays and the development of novel wastewater technologies.

Horizontal transfer and driving factors of extended-spectrum β-lactamase-producing resistance genes in mice intestine after the ingestion of contaminated water

Extended-spectrum β-lactamase (ESBL)-producing Escherichia coli (E. coli) has been identified in various water environments, posing a serious risk to public health. However, whether and how ESBL-producing genes in water-derived E. coli can spread among mammalian gut microbiota via drinking water is largely unclear. To address this problem, horizontal transfer characterization of ESBL-producing genes in mice gut microbiota was determined after the oral ingestion of contaminated water by ESBL-producing E. coli, and then the driving factors were comprehensively examined from multiple different perspectives. The results showed that water-borne ESBL-producing E. coli can colonize in the mice intestine, the ESBL-producing genes can horizontally spread among gut microbiota, and the recipient bacteria include opportunistic pathogens Klebsiella pneumoniae and Salmonella enterica. This horizontal spread may be attributed to the intestinal micro-environment changes caused by the ingestion of contaminated water by ESBL-producing E. coli. These changes, including gut microbiota diversity, increased levels of inflammatory response and reactive oxygen species, cell membrane permeability, and expression levels of conjugative transfer-related genes, are all major driving factors for horizontal transfer of ESBL-producing genes in mice gut microbiota. Our findings highlight the potential for ESBL-producing E. coli to spread resistance genes to mammalian gut microbiota during ingestion of contaminated water.

ECHIDNA (Emerging CHemIcals Database for National Awareness): a framework to prioritise contaminants of emerging concern in water

The widespread presence of contaminants of emerging concern (CEC) in surface waters, treated wastewater and drinking water is an ongoing issue for the water industry. The absence of regulatory guidance and limited occurrence, toxicity and removal data are defining criteria of CEC and make it difficult to prioritise which CEC pose the greatest risk. The online Emerging CHemIcals Database for National Awareness (ECHIDNA) aims to classify and prioritise CEC based on their potential risk, with the information presented in an easily accessible and intuitive manner. A candidate list of almost 1,800 potential CEC, including pesticides, pharmaceuticals and industrial compounds, was compiled using both Australian and international resources. These were ranked based on in silico assessment of their persistent, bioaccumulative and toxic (PBT) properties, as well as potential chronic toxicity hazard, yielding 247 CEC for further prioritisation. Risk Quotients (RQ) identified between 5 and 87 CEC posing a risk to human and ecosystem health, respectively, across drinking water, surface water, treated wastewater and raw wastewater. While the ability of the water industry to effectively prioritise CEC is limited by candidate identification and data availability, ECHIDNA can provide valuable information for better decision-making surrounding CEC management.

Fluorescent Dissolved Organic Matter Components as Surrogates for Disinfection Byproduct Formation in Drinking Water: A Critical Review

Disinfection byproduct (DBP) formation, prediction, and minimization are critical challenges facing the drinking water treatment industry worldwide where chemical disinfection is required to inactivate pathogenic microorganisms. Fluorescence excitation-emission matrices-parallel factor analysis (EEM-PARAFAC) is used to characterize and quantify fluorescent dissolved organic matter (FDOM) components in aquatic systems and may offer considerable promise as a low-cost optical surrogate for DBP formation in treated drinking waters. However, the global utility of this approach for quantification and prediction of specific DBP classes or species has not been widely explored to date. Hence, this critical review aims to elucidate recurring empirical relationships between common environmental fluorophores (identified by PARAFAC) and DBP concentrations produced during water disinfection. From 45 selected peer-reviewed articles, 218 statistically significant linear relationships (R2 ≥ 0.5) with one or more DBP classes or species were established. Trihalomethanes (THMs) and haloacetic acids (HAAs), as key regulated classes, were extensively investigated and exhibited strong, recurrent relationships with ubiquitous humic/fulvic-like FDOM components, highlighting their potential as surrogates for carbonaceous DBP formation. Conversely, observed relationships between nitrogenous DBP classes, such as haloacetonitriles (HANs), halonitromethanes (HNMs), and N-nitrosamines (NAs), and PARAFAC fluorophores were more ambiguous, but preferential relationships with protein-like components in the case of algal/microbial FDOM sources were noted. This review highlights the challenges of transposing site-specific or FDOM source-specific empirical relationships between PARAFAC component and DBP formation potential to a global model.

Production and characterization of graphene oxide-engineered biochars and application for organic micro-pollutant adsorption from aqueous solutions

In this study, conventional and Graphene Oxide-engineered biochars were produced and thoroughly characterized, in order to investigate their potential as adsorptive materials. Two types of biomass, Rice Husks (RH) and Sewage Sludge (SS), two Graphene Oxide (GO) doses, 0.1% and 1%, and two pyrolysis temperatures, 400 °C and 600 °C were investigated. The produced biochars were characterized in physicochemical terms and the effect of biomass, GO functionalization and pyrolysis temperature on biochar properties was studied. The produced samples were then applied as adsorbents for the removal of six organic micro-pollutants from water and treated secondary wastewater. Results showed that the main factors affecting biochar structure was biomass type and pyrolysis temperature, while GO functionalization caused significant changes on biochar surface by increasing the available C- and O- based functional groups. Biochars produced at 600 °C showed higher C content and Specific Surface Area, presenting more stable graphitic structure, compared to biochars produced at 400 °C. Micro-pollutant adsorption rates were in the range of 39.9%-98.3% and 9.4%-97.5% in table water and 28.3%-97.5% and 0.0%-97.5% in treated municipal wastewater, for the Rice Husk and Sewage Sludge biochars respectively. The best biochars, in terms of structural properties and adsorption efficiency were the GO-functionalized biochars, produced from Rice Husks at 600 °C, while the most difficult pollutant to remove was 2.4-Dichlorophenol.

Genotoxicity and endocrine disruption potential of haloacetic acids in human placental and lung cells

Chlorination of water results in the formation of haloacetic acids (HAAs) as major disinfection byproducts (DBPs). Previous studies have reported some HAAs species to act as cytotoxic, genotoxic, and carcinogenic. This work aimed at further exploring the toxicity potential of the most investigated HAAs (chloroacetic (CAA), bromoacetic (BAA), iodoacetic (IAA) acid) and HAAs species with high content of bromine (tribromoacetic acid (TBAA)), and iodine in their structures (chloroiodoacetic (CIAA) and diiodoacetic acid (DIAA)) to human cells. Novel knowledge was generated regarding cytotoxicity, oxidative stress, endocrine disrupting potential, and genotoxicity of these HAAs by using human placental and lung cells as in vitro models, not previously used for DBP assessment. IAA showed the highest cytotoxicity (EC₅₀: 7.5 μM) and ability to generate ROS (up to 3-fold) in placental cells, followed by BAA (EC₅₀: 20-25 μM and 2.1-fold). TBAA, CAA, DIAA, and CIAA showed no significant cytotoxicity (EC₅₀ > 250 μM). All tested HAAs decreased the expression of the steroidogenic gene hsd17b1 up to 40 % in placental cells, and IAA and BAA (0.01-1 μM) slightly inhibited the aromatase activity. HAAs also induced the formation of micronuclei in A549 lung cells after 48 h of exposure. IAA and BAA showed a non-significant increase in micronuclei formation at low concentrations (1 μM), while BAA, CAA, CIAA and TBAA were genotoxic at exposure concentrations above 10 μM (100 μM in the case of DIAA). These results point to genotoxic and endocrine disruption effects associated with HAA exposure at low concentrations (0.01-1 μM), and the usefulness of the selected bioassays to provide fast and sensitive responses to HAA exposure, particularly in terms of genotoxicity and endocrine disruption effects. Further studies are needed to define thresholds that better protect public health.

Impact of a megacity on the water quality of a tropical estuary assessed by a combination of chemical analysis and in-vitro bioassays

Tropical estuaries are threatened by rapid urbanization, which leads to the spread of thousands of micropollutants and poses an environmental risk to such sensitive aqueous ecosystems. In the present study, a combination of chemical and bioanalytical water characterization was applied to investigate the impact of Ho Chi Minh megacity (HCMC, 9.2 million inhabitants in 2021) on the Saigon River and its estuary and provide a comprehensive water quality assessment. Water samples were collected along a 140-km stretch integrating the river-estuary continuum from upstream HCMC down to the estuary mouth in the East Sea. Additional water samples were collected at the mouth of the four main canals of the city center. Chemical analysis was performed targeting up to 217 micropollutants (pharmaceuticals, plasticizers, PFASs, flame retardants, hormones, pesticides). Bioanalysis was performed using six in-vitro bioassays for hormone receptor-mediated effects, xenobiotic metabolism pathways and oxidative stress response, respectively, all accompanied by cytotoxicity measurement. A total of 120 micropollutants were detected and displayed high variability along the river continuum with total concentration ranging from 0.25 to 78 μg L^-1. Among them, 59 micropollutants were ubiquitous (detection frequency ≥ 80 %). An attenuation was observed in concentration and effect profiles towards the estuary. The urban canals were identified as major sources of micropollutants and bioactivity to the river, and one canal (Bến Nghé) exceeded the effect-based trigger values derived for estrogenicity and xenobiotic metabolism. Iceberg modelling apportioned the contribution of the quantified and the unknown chemicals to the measured effects. Diuron, metolachlor, chlorpyrifos, daidzein, genistein, climbazole, mebendazole and telmisartan were identified as main risk drivers of the oxidative stress response and xenobiotic metabolism pathway activation. Our study reinforced the need for improved wastewater management and deeper evaluations of the occurrence and fate of micropollutants in urbanized tropical estuarine environments.

Emerging organic contaminants in springs of the highly karstified Dinaric region

Emerging organic contaminants (EOCs) have become of increasing interest due to concerns about their impact on humans and the wider environment. Karst aquifers are globally widespread, providing critical water supplies and sustaining rivers and ecosystems, and are particularly susceptible to pollution. However, EOC distributions in karst remain quite poorly understood. This study looks at the occurrence of EOCs in the Croatian karst, which is an example of the "classical" karst, a highly developed type of karst that occurs throughout the Dinaric region of Europe. Samples were collected from 17 karst springs and one karst lake used for water supply in Croatia during two sampling campaigns. From a screen of 740 compounds, a total of 65 compounds were detected. EOC compounds from the pharmaceutical (n = 26) and agrochemical groups (n = 26) were the most frequently detected, while industrials and artificial sweeteners had the highest concentrations (range 8-440 ng/L). The number of detected compounds and the frequency of detection demonstrate the vulnerability of karst to EOC pollution. Concentrations of 5 compounds (acesulfame, sucralose, perfluorobutane sulfonate, emamectin B1b, and triphenyl phosphate) exceeded EU standards and occurred at concentrations that are likely to be harmful to ecosystems. Overall, most detections were at low concentrations (50 % <1 ng/L). This may be due to high dilution within the exceptionally large springs of the Classical karst, or due to relatively few pollution sources within the catchments. Nevertheless, EOC fluxes are considerable (10 to 10⁶ ng/s) due to the high discharge of the springs. Temporal differences were observed, but without a clear pattern, reflecting the highly variable nature of karst springs that occurs over both seasonal and short-term timescales. This research is one of a handful of regional EOC investigations in karst groundwater, and the first regional study in the Dinaric karst. It demonstrates the need for more frequent and extensive sampling of EOCs in karst to protect human health and the environment.

Complete oxidative degradation of diclofenac via coupling free radicals and oxygenases of a micro/nanostructured biogenic Mn oxide composite from engineered Pseudomonas sp. MB04R-2

Oxidative degradation can effectively degrade aromatic emerging contaminants (ECs). However, the degradability of lone inorganic/biogenic oxides or oxidases is typically limited when treating polycyclic ECs. Herein, we report a dual-dynamic oxidative system comprising engineered Pseudomonas and biogenic Mn oxides (BMO), which completely degrades diclofenac (DCF), a representative halogen-containing polycyclic EC. Correspondingly, recombinant Pseudomonas sp. MB04R-2 was constructed via gene deletion and chromosomal insertion of a heterologous multicopper oxidase cotA, allowing for enhanced Mn(II)-oxidizing activity and rapid formation of the BMO aggregate complex. Additionally, we characterized it as a micro/nanostructured ramsdellite (MnO₂) composite using multiple-phase composition and fine structure analyses. Furthermore, using real-time quantitative polymerase chain reaction, gene knockout, and expression complementation of oxygenase genes, we demonstrated the central and associative roles of intracellular oxygenases and cytogenic/BMO-derived free radicals (FRs) in degrading DCF and determined the effects of FR excitation and quenching on the DCF degradation efficiency. Finally, after identifying the degraded intermediates of ²H-labeled DCF, we constructed the DCF metabolic pathway. In addition, we evaluated the degradation and detoxification effects of the BMO composite on DCF-containing urban lake water and on biotoxicity in zebrafish embryos. Based on our findings, we proposed a mechanism for oxidative degradation of DCF by associative oxygenases and FRs.