DGT Passive Sampling for Quantitative in Situ Measurements of Compounds from Household and Personal Care Products in Waters

The influence mechanism of environmental factors on DGT adsorbing sulfonamides and the migration between water and sediment

Obtaining the sulfonamides (SAs) concentrations in the water body and sediment bulk was a prerequisite to reveal their transport and partitioning behavior in sediment-water environments and accurately assess their ecological risk. In the present study, the influences of multifactor interactions on the performance of o-DGTs with XAD-18 binding gels were analyzed by central combination experiments and response surfaces analysis, in which the target compounds were 9 SAs. The results indicated that dissolved organic matter (DOM), pH, and suspended particulate matter (SS) had significant effects on the o-DGT sampling, whereas this o-DGT was independent of the ionic strength (IS). Concentning the composite influence of the four factors, the interaction between DOM and SS posed the most significant effect on all 9 SAs compounds. Subsequently, an o-DGT and DIFS model was applied to explore the SAs migration between the water-sediments interface. The difference between desorption rate (kb) and adsorption rates (kf) values suggested that the kinetics of SAs was dominated by adsorption. Moreover, the short-term sediment-water partitioning of SAs was clarified on the basis of distribution coefficient (Kdl) for the labile SAs, among which the sulfadiazine (SDZ) had the largest labile pool. The ability of sediments to release SAs to the liquid phase as a sink was determined by response time (Tc). Among the 9 SAs, the long-term release of soseulfamethoxypyridazine (SMP) from the solid phase of sediments would have a potential risk to the aquatic environment, to which more attention should be paid in the future.

Occurrence and distribution of PAHs in the Yangtze River and urban river waters of Nanjing, China: Insights from in situ DGT measurements

The diffusive gradients in thin films (DGT) technique has been used for monitoring various organic pollutants in surface water in recent years. This article applies a novel DGT passive sampler to the Nanjing section of the Yangtze River and urban rivers to measure the in-situ concentrations of polycyclic aromatic hydrocarbons (PAHs), analyze their seasonal changes and determine their fate. PAH concentrations had marked seasonality. The concentration of individual PAH was 1.3-18 ng/L in summer and 4.2-161 ng/L in winter. Source inputs, flow differences and degradation/losses caused the seasonal differences. Inputs from Nanjing and tributary rivers were minor compared to the cumulative loads of PAHs in the main Yangtze river upstream of the city. Petrochemical enterprises along the Yangtze River, ship transportation, and upstream pollution were the main sources of pollution in this area. Source analysis indicated a mixed source with coal and biomass combustion inputs increasing significantly in winter. Risk assessment indicated that although the Yangtze River protection policy has reduced pollution in recent years, water quality still exceeded PAH ecological thresholds in the river and the chemical industry cluster areas during winter. Further measures are needed to reduce pollution and its associated risks from a catchment perspective.

Diffusive gradients in thin-films (DGT) for in situ measurement of neonicotinoid insecticides (NNIs) in waters

Neonicotinoid insecticides (NNIs) are among the most widely-used insecticides, although their threat to non-target organisms has attracted attention in recent years. In this study, a diffusive gradient in thin-films (DGT) passive sampling technique was developed for in situ monitoring of time-weighted average (TWA) concentrations of NNIs in groundwater and wastewater. Systematic studies demonstrated that DGT with HLB as binding gels (HLB-DGT) is suitable for quantitative sampling of NNIs under a wide range of conditions, independent of pH (5-9.5), ionic strength (0.001-0.5 M) and dissolved organic matter (0-10 mg/L). The HLB-DGT performance was also independent of the typical groundwater ionic environments. The thicknesses of in-situ measured diffusive boundary layer were 0.35 and 0.25 mm in the groundwater and effluent, respectively. HLB-DGT can provide TWA concentrations over 14-18 days' deployment with linear uptake in both groundwater and wastewater. Concentrations and occurrence patterns of NNIs obtained by HLB-DGT were consistent with those measured from grab samples. The median TWA concentration of NNIs was 4.42 ng/L in water from the largest urban lake of China (the Tangxun Lake) in winter, with wastewater discharge being the main potential source. The reliability and stability of the HLB-DGT for measuring NNIs in the groundwater and surface water were confirmed and can be used to improve understanding of the occurrence and fate of NNIs in aquatic environment.

Development and validation of diffusive gradients in thin-films for in situ monitoring of ionic liquids in waters

Due to their wide applications, occurrence and "PFAS-like" environmental behaviors, ionic liquids (ILs) represent a new challenge for the environmental monitoring community, who require robust analytical methods that can determine accurately and efficiently their environmentally relevant concentrations. A new passive sampling method based on the diffusive gradients in thin films (DGT) technique was developed for the measurement of imidazole-based ILs in waters using a mixed-mode cation exchange (MCX) resin as the adsorbent. The selected binding gel had a high binding capacity (>170 μg per disc) for ILs. Diffusion coefficients measured using a diffusion cell correlated well with alkyl chain lengths (r2 = 0.95) and retention times (r2 = 0.88), providing a simple and rapid prediction approach for other ILs. The assembled MCX-DGT sampler exhibited a linear accumulation for at least 120 h. MCX-DGT also showed good performance under typical freshwater conditions (pH 5-8, ionic strength 0.001-0.01 M, and humic acid 0-5 mg L-1), while still being problematic for aquatic conditions with higher ionic strength (>0.1 M) or DOM (>10 mg L-1). Laboratory deployment (for up to 3 days) in spiked natural freshwater (SNW) resulted in linear mass uptakes for the short-chain ILs (C2-C8), and their DGT-measured concentrations agreed well with solution concentrations. However, MCX-DGT significantly overestimated the concentrations of the long-chain ILs (C10-C12) when deployed in SNW for one day or more, which is attributed to the strong competitive adsorption of the long-chain ILs by natural organic matter. In situ field evaluation along with grab sampling found no target ILs in a wastewater treatment plant and its receiving river, implying that these new chemicals might not be widely used in South China now. This is the first report on the DGT technique for ILs and might provide an effective tool for monitoring short chain length ILs in the aquatic environment in the near future.

Development and application of diffusive gradients in thin-films for in-situ monitoring of 6PPD-Quinone in urban waters

The occurrence and risk of N-(1,3-dimethylbutyl)-N'-phenyl-p-phenylenediamine-quinone (6PPD-Q), derived from the oxidation of the tire antidegradant 6PPD, has raised significant concern since it was found to cause acute mortality in coho salmon when exposed to urban runoff. Given the short half-life period and low solubility of 6PPD-Q, reliable in situ measurement techniques are required to accurately understand its occurrence and behaviour in aquatic environments. Here, using the diffusive gradients in thin-films (DGT) method with HLB as a binding agent, we developed a new methodology to measure 6PPD-Q in urban waters. 6PPD-Q was rapidly and strongly adsorbed on the HLB-binding gel and was efficiently extracted using organic solvents. The HLB-DGT accumulated 6PPD-Q linearly for >7 d and its performance was not significantly affected by pH (6.5-8.5), ionic strength (0.0001-0.5 M) or dissolved organic matter (0-20 mg L-1). Field evaluation of the DGT method demonstrated its effectiveness in urban runoff, detecting 6PPD-Q levels of 15.8-39.5 ng L-1 in rivers. In snowmelt, DGT detected 6PPD-Q levels of 210 ng L-1 which is two times higher than the value obtained by grab sampling. 6PPD-Q levels were much higher in snowmelt than those in rivers. This indicates that snowfall constitutes an important transport pathway for 6PPD-Q and that DGT effectively captured the fraction continuously released from dust particles in the snow samples. 6PPD-Q posed a substantial risk to migratory fish in urban waters, and its release from tire wear particles requires further investigation. This study is the first to develop a DGT-based method for 6PPD-Q determination in urban waters, and the method can ensure an accurate measurement of the release of 6PPD-Q to the environment, particularly in rainfall or snowmelt, important pathways for its entry into the aquatic environment.

Development and validation of an imprinted polymer based DGT for monitoring β-blocker drugs in wastewater surveillance

Wastewater surveillance is an effective and objective approach to monitor contaminant releases and drug usage in the catchment, the estimation requires accurate measurement. In this study, a novel diffusive gradients in thin-film (DGT) technique based on molecularly imprinted polymers (MIPs) for selective measurement of a class of widely prescribed cardiovascular drugs (β-blockers) in wastewater was developed. The synthesized MIPs showed strong affinity and selectivity for the target compounds. The MIP-DGT had large effective capacities, its performance was independent of a wide range of environmental conditions, including pH (4.58 - 8.89), ionic strength (0.01 - 0.5 M) and dissolved organic matter (< 20 mg L-1). Biofouling had little effect on the uptake of target compounds within 7 days. MIP-DGT devices were applied in a Chinese urban WWTP alongside an auto-sampler. Metoprolol concentrations detected were much higher than other β-blockers. Concentrations obtained using MIP-DGT were comparable to the 24 h composite samples using an autosampler. The estimated daily consumption calculated based on the data obtained with MIP-DGT implied that metoprolol and propranolol were the most popular β-blockers in the studied area. Overall, the results in this study demonstrate that the MIP-DGT is a cost-effective, reliable and efficient tool for in situ wastewater monitoring.

On-site evaluation of DGT passive sampling for quantitatively measuring per- and polyfluoroalkyl substances in a river-estuary-sea water system

The passive sampling technique of diffusive gradients in thin-films (DGT) is promising for monitoring emerging contaminants such as per- and polyfluoroalkyl substances (PFAS). It is urgent to evaluate the impacts of salinity and exposure time on DGT sampling before it can be set as a standard method. Herein, DGT sampler based on the binding gel of weak anion exchanger (WAX) resin was deployed in a representative water system of the Xiaoqing river-estuary-sea for representative sampling windows (<1 day to 28 days) with high pH (8.18 ± 0.04 to 8.51 ± 0.17) and wide ranges of salinity (0.95 ± 0.07‰ to 14.37 ± 3.92‰), total dissolved solids (1.20 ± 0.09 g/L to 15.29 ± 3.91 g/L) and dissolved organic matter (2.8-32 mg/L). The results showed that the WAX-DGT sampler exhibited good performance for most target PFAS except for short-chain perfluorocarboxylates (C ≤ 5) in 14 days. When the exposure time was over 14 days, biofouling of the sampler may deflect the mass accumulation of the PFAS in the sampler. Salinity played an important role in the mass binding of PFAS by DGT. The shorter the carbon chain of the compound, the greater the influence of the salinity. PFAS with carboxyl groups had greater affinities for the biofouled membrane filter than those with sulfonic groups. In the river-estuary-sea system, where PFAS concentrations changed dynamically, the temporal resolution of the monitoring strategy has been demonstrated to be more important than spatial resolution. DGT provided a better integral of PFAS exposure than grab sampling in the dynamic water system and offered equivalent sensitivity of grab sampling with exposure time <10 d and greater sensitivity with exposure time ≥10 d. Thus, DGT has the advantage of providing high temporal resolution monitoring. This study provided support for the standardization of the DGT technique.

Utility of a modified o-DGT passive sampler for measurement of bisphenol analogues in freshwater and coastal waters

Bisphenol analogues (BPs) are commonly found in riverine and coastal waters. However, the lack of a reliable and robust passive sampling method has hindered our ability to monitor these compounds in aquatic systems. The study developed a novel organic-diffusive gradients in thin film (o-DGT) sampler based on stainless steel mesh membrane, polyacrylamide diffusive gel, and hydrophilic-lipophilic balance (HLB) binding gel. This innovative design tackled issues of filter membrane sorption in traditional o-DGT devices and potential gel damage in membrane-less o-DGT devices, showing promising application prospects. The mass accumulation of 15 target BPs was linear over 10 days in both freshwater (r2 ≥ 0.92) and seawater (r2 ≥ 0.94), with no saturation observed. The diffusion coefficients (D) through polyacrylamide diffusive gels ranged from 4.04 × 10-6 to 5.77 × 10-6 cm2 s-1 in freshwater and from 1.74 × 10-6 to 4.69 × 10-6 cm2 s-1 in seawater for the target BPs (except for bisphenol PH) at 22 °C. The D values of the target BPs in seawater were lower than those in freshwater due to the high salinity in seawater (35 ‰). The o-DGT samplers demonstrated good integrity in field applications. The total concentrations of the eight detected BPs ranged from 9.2 to 323 ng L-1, which was consistent with the measurements obtained by grab sampling. Among all BPs, bisphenol S, bisphenol F, and bisphenol A were consistently detected at all sites using both sampling methods. The concentrations of some novel BPs in coastal water measured by grab sampling were comparable to those measured in rivers, suggesting the need to strengthen pollution control of BPs in coastal areas. These results indicate that the o-DGT passive sampling method developed in the present study can be effectively used for monitoring BPs in freshwater and coastal environments.

Development of diffusive gradients in thin-films technique for monitoring polycyclic aromatic hydrocarbons in coastal waters

Addressing the challenge of accurately monitoring polycyclic aromatic hydrocarbons (PAHs) in aquatic systems, this study employed diffusive gradients in thin-films (DGT) technique to achieve methods detection limits as low as 0.02 ng L-1 to 0.05 ng L-1 through in situ preconcentration and determination of time-integrated concentrations. The efficacy of the developed DGT samplers was validated under diverse environmental conditions, demonstrating independence from factors such as pH (5.03-9.01), dissolved organic matter (0-20 mg L-1), and ionic strength (0.0001-0.6 M). Notably, the introduction of a novel theoretical approach to calculate diffusion coefficients based on solvent-accessible volume tailored for PAHs significantly enhanced the method's applicability, particularly for organic pollutants with low solubility. Field deployments in coastal zones validated the DGT method against traditional grab sampling, with findings advocating a 4 to 7-day optimal deployment duration for balancing sensitivity and mitigating lag time effects. These results provide a sophisticated, efficient solution to the persistent challenge of monitoring hydrophobic organic pollutants in aquatic environments, broadening the scope and applicability of DGT in environmental science and providing a robust tool for researchers.

Exposure to environmental pollutants: A mini-review on the application of wastewater-based epidemiology approach

Wastewater-based epidemiology (WBE) is considered an innovative and promising tool for estimating community exposure to a wide range of chemical and biological compounds by analyzing wastewater. Despite scholars' interest in WBE studies, there are uncertainties and limitations associated with this approach. This current review focuses on the feasibility of the WBE approach in assessing environmental pollutants, including pesticides, heavy metals, phthalates, bisphenols, and personal care products (PCPs). Limitations and challenges of WBE studies are initially discussed, and then future perspectives, gaps, and recommendations are presented in this review. One of the key limitations of this approach is the selection and identification of appropriate biomarkers in studies. Selecting biomarkers considering the basic requirements of a human exposure biomarker is the most important criterion for validating this new approach. Assessing the stability of biomarkers in wastewater is crucial for reliable comparisons of substance consumption in the population. However, directly analyzing wastewater does not provide a clear picture of biomarker stability. This uncertainty affects the reliability of temporal and spatial comparisons. Various uncertainties also arise from different steps involved in WBE. These uncertainties include sewage sampling, exogenous sources, analytical measurements, back-calculation, and estimation of the population under investigation. Further research is necessary to ensure that measured pollutant levels accurately reflect human excretion. Utilizing data from WBE can support healthcare policy in assessing exposure to environmental pollutants in the general population. Moreover, WBE seems to be a valuable tool for biomarkers that indicate healthy conditions, lifestyle, disease identification, and exposure to pollutants. Although this approach has the potential to serve as a biomonitoring tool in large communities, it is necessary to monitor more metabolites from wastewater to enhance future studies.

Development of a novel DGT passive sampler for measuring polycyclic aromatic hydrocarbons in aquatic systems

Polycyclic aromatic hydrocarbons (PAHs) are priority pollutants and need to be measured reliably in waters and other media, to understand their sources, fate, behaviour and to meet regulatory monitoring requirements. Conventional water sampling requires large water volumes, time-consuming pre-concentration and clean-up and is prone to analyte loss or contamination. Here, for the first time, we developed and validated a novel diffusive gradients in thin-films (DGT) passive sampler for PAHs. Based on the well-known DGT principles, the sampler pre-concentrates PAHs with typical deployment times of days/weeks, with minimal sample handling. For the first time, DGT holding devices made of metal and suitable for sampling hydrophobic organic compounds were designed and tested. They minimize sorption and sampling lag times. Following tests on different binding layer resins, a MIP-DGT was preferred - the first time applying MIP for PAHs. It samples PAHs independent of pH (3.9 -8.1), ionic strength (0.01 -0.5 M) and dissolved organic matter < 20 mg L-1, making it suitable for applications across a wide range of environments. Field trials in river water and wastewater demonstrated that DGT is a convenient and reliable tool for monitoring labile PAHs, readily achieving quantitative detection of environmental levels (sub-ng and ng/L range) when coupled with conventional GC-MS or HPLC. ENVIRONMENTAL IMPLICATIONS: PAHs are carcinogenic and genotoxic compounds. They are environmentally ubiquitous and must be monitored in waters and other media. This study successfully developed a new DGT passive sampler for reliable in situ time-integrated measurements of PAHs in waters at the ng/L level. This is the first time to use passive samplers for accurate measurements of hydrophobic organic contaminants in aquatic systems without calibration, a big step forward in monitoring PAHs. The application of this new sampler will enhance our understanding of the sources, fate, behavior and ecotoxicology of PAHs, enabling improved environmental risk assessment and management of these compounds.

Development and validation of an in situ high-resolution technique for measuring antibiotics in sediments

Important biogeochemical processes occur in sediments at fine scales. Sampling techniques capable of yielding information with high resolution are therefore needed to investigate chemical distributions and fluxes and to elucidate key processes affecting chemical fates. In this study, a high-resolution diffusive gradients in thin-films (DGT) technique was systematically developed and tested in a controlled sediment system to measure organic contaminants, antibiotics, for the first time. The DGT probe was used to resolve compound distributions at the mm scale. It also reflected the fluxes from the sediment pore-water and remobilization from the solid phase, providing more dynamic information. Through the fine scale detection, a reduction of re-supply was observed over time, which was concentration and location dependent. Compared to the Rhizon sampling method, antibiotic concentrations obtained by DGT probes were less than the pore-water concentrations, as DGT measures the labile fraction of the compounds. The DGT probe was also tested on an intact sediment core sampled from a lake in China and used to measure the distribution of labile antibiotics with depth in the core at the mm scale. ENVIRONMENTAL IMPLICATION: The abuse of antibiotics and widespread of their residues influences the ecosystem, induces the generation of super-bacteria, and finally poses threat to human health. Sediments adsorbs pollutants from the aquatic environment, while may also release them back to the environment. We systematically developed DGT probe approach for measuring antibiotics in sediment in situ in high resolving power, it provides information at fine scale to help us investigate biogeochemical processes take place in sediment and sediment-water interface.

A critical review of distribution, toxicological effects, current analytical methods and future prospects of synthetic musks in aquatic environments

Synthetic musks (SMs) have gained widespread utilization in daily consumer products, leading to their widespread dissemination in aquatic environments through various pathways. Over the past few decades, the production of SMs has consistently risen, prompting significant concern over their potential adverse impacts on ecosystems and human health. Although several studies have focused on the development of analytical techniques for detecting SMs in biological samples and cosmetic products, a comprehensive evaluation of their global distribution in diverse aquatic media and biological matrices remains lacking. This review aims to provide an up-to-date overview of the occurrence of SMs in both aquatic and various biological matrices, investigating their worldwide distribution trends, assessing their ecological toxicity, and comparing different methodologies for processing and analysis of SMs. The findings underscore the prevalence of polycyclic musks as predominant SMs, with consumption of various products in different countries leading to contrasting distribution of contaminants. Furthermore, the migration of SMs from sediments to the water phase is investigated, indicating the role of solid-phase reservoirs. Incomplete degradation of SMs in the environment could contribute to their accumulation in aquatic systems, impacting the growth and oxidative stress of aquatic organisms, and having a possibility of genotoxicity to them. Human exposure data highlight substantial risks for vulnerable populations such as pregnant women and infants. Moreover, contemporary methods for SMs analysis are presented in this review, particularly focusing on advancements made in the last five years. Finally, research enhancement and critical questions regarding the analysis of SMs are provided, offering suggestions for future research endeavors.

Occurrence and distribution of PPCPs in water from two largest urban lakes of China: First perspective from DGT in-situ measurement

Pharmaceutical and personal care products (PPCPs) are an important group of emerging contaminants that may threaten organisms at trace concentrations. However, research on the occurrence of PPCPs in urban lakes in China is still scarce. In this study, 15 PPCPs in the Tangxun Lake and the Donghu Lake were collected using the diffusive gradients in thin-films (DGT) technique and analyzed by high performance liquid chromatography tandem-mass spectrometry (HPLC-MS/MS). Thirteen of the 15 targeted PPCPs were detected in the Tangxun Lake, and all PPCPs were detected in the Donghu Lake, with total concentrations ranging from 160 to 730 ng/L (average: 401 ng/L) and 187 to 1933 ng/L (average: 653 ng/L), respectively. Bisphenol A (BPA) was the dominant PPCP, followed by disinfectants in both lakes. The total concentrations of PPCPs in the Donghu Lake were higher than those in the Tangxun Lake. The spatial distribution characteristics of PPCPs in the two lakes were different, with higher total concentrations in the eastern part than in the western part of the Tangxun Lake spatially and higher in the north-western part than in the south-eastern part of the Donghu Lake. The results of the risk assessment showed that BPA and estrone posed high risks to the aquatic environment (RQ ≥ 1), while triclosan and estriol presented a medium risk (0.1 ≤ RQ < 1) in some sites. This study was the first attempt to apply DGT for providing vital data on the evaluation of the ecological risk of PPCPs in the two largest lakes in China, and attention should be paid to the long-term ecological effects caused by the occurrence of PPCPs in lakes.

Factors affecting diffusion of polar organic compounds in agarose hydrogel applied to control mass transfer in passive samplers

Diffusive hydrogel-based passive sampler (HPS) based on diffusive gradients in thin films (DGT) is designed for monitoring polar organic contaminants in the aquatic environment. DGT technique controls the compound's overall uptake rate by adding a hydrogel layer of known thickness, which minimizes the importance of the resistive water boundary layer in the compound uptake process. In this work, we investigated several factors which may influence the diffusion of a range of aquatic contaminants in 1.5% agarose hydrogel. Diffusion in hydrogel was tested using the sheet stacking method. We demonstrated that a thin nylon netting incorporated into the diffusive hydrogel for mechanical strengthening does not significantly affect the diffusion of 11 perfluoroalkyl compounds. Further, we investigated the effect of pH in the range from 3 to 11 on the diffusion of a range of 39 aromatic amines (AAs) -36 aromatic, 2 aliphatic, and azobenzene in hydrogel. AAs were chosen as representatives of compounds with pH-dependent dissociation in water. Analysis of variance showed no significant difference in mean diffusion coefficient log D value at five pH values. The demonstration that the diffusion coefficient D and thus the sampling rate Rs are independent on pH simplifies the interpretation of data from field studies because we can neglect the influence of pH on the Rs. log D values (m2 s-1) of tested AAs ranged from to - 9.77 for 3,3'-dimethylbenzidine to - 9.19 for azobenzene. A negative correlation of log D with molar mass (log M) and molecular volume (log Vm) was observed (R =  - 0.57 and - 0.56, respectively). The diffusion coefficient presents a critical parameter for the sampling rate estimation of HPS. Theoretical sampling rates Rs of AAs were calculated for a HPS using the average D values. Theoretical Rs values calculated for AAs at 22°C ranged from 29 mL day-1 for 3,3'-dimethylbenzidine to 106 mL day-1 for 2-aminopyridine. Our calculated values of Rs are in the same range as those already published for a range of low-molecular polar organic contaminants, which supports the possibility of deriving sampler performance parameters in the field from laboratory-derived diffusivity of analytes in hydrogel.

Influence of copper and aging on freely dissolved tetracycline concentration in soil

Copper (Cu) and tetracyclines (TCs) often coexist in agricultural soils because of the use of manures on farmland; however, the influence of Cu on the bioavailability of TCs is still unclear, especially for cases with aging Cu. The freely dissolved concentrations (FDCs) of TCs are believed to be directly related to their bioavailability. In the present study, the FDCs of TCs were determined using organic-diffusive gradients in thin films (o-DGT), and the influence of Cu on the FDCs of TCs in soils was evaluated. The results showed that the FDCs of tetracycline (TC), oxytetracycline (OTC), and chlortetracycline (CTC) were 0.11-0.93, 0.28-1.02, and 0.24-0.53 μg/kg in the CK groups (no Cu added) and accounted for 0.09-0.58, 0.10-1.40, and 0.05-1.19‰ of their total concentrations which ranged from 0.2 to 10.0 mg/kg for TC, OTC, and CTC, respectively. The co-contamination of Cu reduced the FDCs of TCs in most cases, and aging increased the influence of Cu. The presence of Cu resulted in a decrease in the TC FDC by 35.48-95.04% in aged soils and 3.42-87.19% in newly prepared soils. FTIR analysis revealed that aging facilitated the bonding of Cu to soil particles via Cu-O, and Cu bonded to groups such as hydroxyl groups (-OH) in TCs. Our results suggested that the presence of Cu might reduce the bioavailability of TCs, and aging would enhance these effects. This is helpful for the bioavailability analysis of TCs under co-contamination of heavy metals.

Rare earth elements in sediments from a representative Chinese mariculture bay: Characterization, DGT-based bioaccessibility, and probabilistic ecological risk

Rare earth elements (REEs) are emerging contaminants due to their worldwide exploitation in the high-technology sector. Aquaculture systems, particularly those located within coastal areas, are fragile ecosystems due to anthropogenic impacts regarding urban and aquaculture activities. However, to date, there are no reports on the combined toxicity of rare earth element (REE) mixtures on aquatic biota in sediments from coastal aquaculture systems. In this study, the combined toxicity of REE mixtures based on probabilistic risk assessment indicated that the surface sediments of Zhelin Bay had a 1.86% probability of toxic effects on aquatic biota. The average value of total REEs (TREEs) was 297.37 μg/g, with light REEs representing the major part. A factor analysis (FA)-geographic information system (GIS)-based approach coupled with correlation analysis (CA) revealed that the REEs are derived from anthropogenic sources through fluvial processes.

Determination of the Isotopic Composition of Aqueous Mercury in a Paddy Ecosystem Using Diffusive Gradients in Thin Films

Measuring the isotopic composition of Hg in natural waters is challenging due to the ultratrace level of aqueous Hg (ng L-1). At least 5 ng of Hg mass is required for Hg isotopic analysis. Given the low Hg concentration in natural waters, a large volume of water (>10 L) is typically needed. The conventional grab sampling method is time-consuming, laborious, and prone to contamination during transportation and preconcentration steps. In this study, a DGT (diffusive gradients in thin films) method based on aminopropyl and mercaptopropyl bi-functionalized SBA-15 nanoparticles was developed and extended to determine the concentration and isotopic composition of aqueous Hg for the first time. The results of laboratory analysis showed that Hg adsorption by DGT induces ∼ -0.2‰ mass-dependent fractionation (MDF) and little mass-independent fractionation (MIF). The magnitude of MDF exhibits a dependence on the diffusion-layer thickness of DGT. Since Hg-MDF can occur in a broad range of environmental processes, monitoring the δ202Hg of aqueous Hg using the DGT method should be performed with caution. Field results show consistent MIF signatures (Δ199Hg) between the DGT and conventional grab sampling method. The developed DGT method serves as a passive sampling method that effectively characterizes the MIF of Hg in waters to understand the biogeochemical cycle of Hg at contaminated sites.

Development and application of diffusive gradients in thin films for in situ sampling of the organic UV filter 4-methylbenzylidene camphor (4-MBC) in waters

4-Methylbenzylidene camphor (4-MBC), a typical organic UV filter (OUVF) in personal care products, is considered to be a potential endocrine disruptor due to its estrogenic activity and bioaccumulation. Although 4-MBC residues have been extensively identified in aquatic waters, little is known about their occurrence, levels, and potential risk in coastal waters. This study developed a reliable sampling approach, based on diffusive gradients in thin films (DGT) with XAD-2 as the binding agent, for monitoring 4-MBC in coastal waters. The diffusion coefficients of 4-MBC in freshwater and artificial seawater were 3.65 × 10-6 cm2/s and 3.83 × 10-6 cm2/s, respectively. XAD-2 binding gel showed rapid adsorption to 4-MBC. The accumulated masses of 4-MBC in XAD-2 DGT increased linearly with deployed time for 7 days in freshwater and seawater, which agreed well with theoretical predictions. The sampling performance was independent of ionic strength (0.0001-0.5 M), pH (4.0-8.5), and dissolved organic matter (0-20 mg/L). Field deployment in the river estuary and bathing beach showed that DGT-measured 4-MBC concentrations were consistent in comparison with grab sampling. Environmental risk assessment showed that 4-MBC may pose a medium risk to aquatic organisms based on computed risk quotient (RQ) values. Sewage discharge is the main source of 4-MBC risk, while the residue in recreation beaches contributes more significantly in summer. The established DGT sampling is suitable for seasonal monitoring, source identification, and risk assessment of 4-MBC in coastal waters.

Insights into the release of triclosan from microplastics in aquatic environment assessed with diffusive gradient in thin-films

Organic chemicals associated with microplastics (MPs) can be released and thus pose potential risks during weathering processes. However, the thermodynamics and kinetics of their release processes still need to be better understood. Herein, the adsorption and desorption kinetics of triclosan on polystyrene (PS) and polyvinyl chloride (PVC) were investigated by using both batch experiments and diffusive gradients in thin-films (DGT) technique. The pseudo-second-order model fitted the data best, implying that both intraparticle diffusion and external liquid film diffusion influence the adsorption and desorption processes. DGT continuously accumulated triclosan from MP suspensions but slower than theoretical values, indicating some restrictions to desorption. The DGT-induced fluxes in Soils/Sediment (DIFS) model, employed to interpret DGT data, gave distribution coefficients for labile species (K_dl) of 5000 mL g^-1 (PS) and 1000 mL g^-1 (PVC) and the corresponding response times (T_c) were 10 s and 1000 s, respectively. Higher K_dl but smaller T_c for PS than PVC showed that more triclosan adsorbed on PS could be rapidly released, while there were some kinetic limitations for triclosan on PVC. A novel finding was that pH and ionic strength individually and interactively affected the supply of triclosan to DGT. This is the first study to quantify interactions of organics with MPs by using DGT, aiding our understanding of MPs' adsorption/desorption behavior in the aquatic environment.

Calibration comparison between two passive samplers -o-DGT and POCIS- for 109 hydrophilic emerging and priority organic compounds

The Polar Organic Chemical Integrative Samplers (POCIS) is the most widely used passive sampler for hydrophilic compounds, but unsuitable for certain ionic organic contaminants. The Diffusive Gradient in Thin-Film technique (o-DGT) has shown positive results for both ionic and hydrophilic compounds. However, a calibration step is now needed to evaluate kinetic constant of accumulation for a wide range of molecules. In this study, o-DGT and POCIS were compared for the sampling of three families of micropollutants of potential risk to aquatic environments: 53 pesticides, 36 pharmaceuticals and 20 hormones. A calibration experiment was conducted to compare the kinetic models and constants from a scientific and practical perspective. The results are discussed in a single table that summarizes the performance of both passive samplers for the 109 compounds of interest. The advantage of o-DGT is that it allows linear accumulation for 72 compounds versus only 33 with POCIS. The mean times to equilibrium obtained with o-DGT are higher than those obtained with POCIS. These results confirm that the presence of a diffusion gel delays the achievement of equilibrium during compound accumulation. Therefore, o-DGT can be considered for situations where POCIS cannot be used due to non-linear accumulation over a typical 14-day deployment period. However, overall sampling rates and mass transfer coefficients also appear reduced with o-DGT, which is explained by the smaller exchange surface area, as well as the consideration of an additional diffusive layer in this device. This paper also showed that the most appropriate membrane to sample polar compounds with o-DGT was a polyethersulfone polymer with a pore size of 5 μm.

DGT method for the in situ measurement of triazines and the desorption kinetics of atrazine in soil

Triazines are frequently detected in nature water and agricultural soils worldwide. They are considered harmful to plants, animals, and the human health. In this study, diffusive gradients in thin films (DGT) method was developed for the assessment of several triazines. DGT device was used for the in situ measurement of atrazine in a pesticide factory and obtained reliable data. The atrazine concentrations measured by DGT, and solvent extraction method was in a constant ratio. The DIFS model was coupled with DGT technique to study the desorption kinetics of atrazine in four kinds of different soils. The yellow-brown soil was more inclined to adsorb atrazine than other three soils. 2_D DIFS model was used to obtain the partition coefficient for labile atrazine (K_dl), the values of the response time (T_c), and desorption/adsorption rates (k₁ and k_-1). The yellow-brown soil has a larger labile pool size, and a faster resupply speed of atrazine. The 1_D DIFS model was used to simulate the profiles of atrazine concentrations in soil solution and solid phase. The results show that the desorption of atrazine in soil was limited by kinetic limitation at short time, and was limited by the solid phase reservoir at long time.

Development and validation of the DGT technique using the novel cryogel for measuring dissolved Hg(II) in the estuary

The complex seawater matrix has significantly influenced the determination of estuarine dissolved Hg(II), hindering its monitoring and risk assessment in maricultural areas. In this work, SiO2-SH-DGT assembled by the sulfhydryl-modified silica cryogel (SiO2-SH cryogel) as the novel binding phase was developed to tackle this problem. The uniform dispersion of the cryogel into binding gel was advantageous for achieving remarkable and comparable capacity, which endowed the estimated diffusion coefficient (D) to be 1.39-3.08 times of the existing research. The SiO2-SH-DGT performance was independent of pH (3-9), ionic strength (10-800 mM), fulvic acid at low content, and seawater matrix (Na+, K+, Ca2+, Cl-), but the high content of Mg2+ did interfere with the Hg(II) accumulation, which manifested as competitive adsorption and diffusion. Therefore, the calibrated model was established by calibrating accumulated mass (M') and diffusion coefficient (D') based on the Mg2+ concentration, its high accuracy was further verified in the lab. Finally, SiO2-SH-DGT was deployed in the three typical aquaculture areas in Beibu Gulf, field trials achieved the actual Hg(II) level to be 1.52-5.38 ng/L with consideration of the diffusion boundary layer. The finding could provide new thought and technical support for metal pollution monitoring in estuary maricultural areas.

Evaluation and Application of a Novel Diffusive Gradients in Thin-Films Technique for In Situ Monitoring of Glucocorticoids in Natural Waters

The potential environmental risks of glucocorticoids (GCs) have attracted attention in the past few decades. In this study, a novel diffusive gradients in thin-films (DGT) device and analytical technique based on the second generation of polar enhanced phase (PEP-2), PEP-2-DGT, were developed for sampling and quantifying natural and synthetic GCs in aquatic systems. The capacity of PEP-2 gels for accumulating all target compounds was >600 μg per disc, sufficient for long-term passive sampling of selected GCs, even in wastewaters. Systematic tests were carried out to verify the application of DGT in natural waters and wastewaters. The performance of PEP-2-DGT devices was independent (C_DGT/C_soln was in the acceptable range of 0.9-1.1) of a wide range of environmental conditions: ionic strength (0.001-0.5 mol L^-1), dissolved organic matter (0-20 mg L^-1), and pH (3.06-9.02). It was tested for various diffusive layer thicknesses (0.565-2.065 mm) and different deployment times (10-168 h). Diffusion coefficients (D) of selected GCs through an agarose-based diffusive gel were determined for the first time (3.80-4.85 × 10^-6 cm^-2 s ^-1 at 25 °C). Linear correlations between D and log K_ow were established for three groups of target GCs (R² = 0.96-0.99). This could enable prediction of D values for other GCs with similar structures in the future, which will help for rapid screening and emergency monitoring. Concentrations and distribution patterns of analytes obtained by PEP-2-DGT devices in five rivers after 7- and 14-day deployments were in accordance with those measured from grab samples, with total GC concentrations ranging from 7 to 27 ng L^-1 at all sampling sites, confirming the reliability and robustness of the DGT devices for monitoring GCs in natural waters. The development of the new DGT technique will help improve understanding of the behavior and fate of these compounds in the aquatic environments.

Genetic Behavior of Tomato (Solanum lycopersicum L.) Germplasm Governing Heavy Metal Tolerance and Yield Traits under Wastewater Irrigation

Wastewater irrigation is a substitute for surface water scarcity, but traces of heavy metals (HMs) result in deleterious implications for soil, crop productivity, and in humans. Crops presenting HMs tolerance in genetic behavior are important for producing tolerant genotypes cultivated under wastewater irrigation. In the first part of this experiment, the results obtained previously are re-assessed in a hydroponic system and similar patterns and concentrations of HMs are found in different tomato organs. Following this trial, the tomato’s (Solanum lycopersicum L.) genetic basis of traits conferring HMs tolerance and yield are assessed when irrigated with waste or canal water. The North Carolina Mating II analysis illustrate the amount of gene action, nature, and inheritance pattern. Genetic components depict the involvement of non-additive, additive, and maternal genetic effects in HMs tolerance inheritance and yield. A noticeable increase in cumulative additive variance for the number of flowers (11,907.2) and the number of fruits (10,557.9) is recorded for tomato plants irrigated with wastewater, illustrating additive gene action. However, female and male (MSf/MSm) square ratios also show an association with cytoplasmic inheritance. For HMs tolerance, both additive and dominant variances appeared to be significant; cumulative dominance variance (4.83, 16.1, 4.69, 76.95, and 249.37) is higher compared to additive variance (0.18, 2.36, 0.19, −0.27, and 14.14) for nickel (Ni), chromium (Cr), lead (Pb), manganese (Mn), and zinc (Zn), respectively, indicating dominance gene action. The genotype RIOGRANDI accumulated and translocated fewer HMs to the aerial part of the plant compared to CLN-2418A and PB-017906, thus presenting a tolerant tomato genotype according to the hydroponic experiment. This also exhibited a differential pattern of gene action for HMs tolerance, suggesting that genotypes possess significant differences for HMs tolerance.

Development and applications of diffusive gradients in thin films for monitoring pharmaceuticals in surface waters

Pharmaceutical contaminants in surface water have raised significant concerns because of their potential ecological risks. In particular, coronavirus disease 2019 (COVID-19)-related pharmaceuticals can be released to surface water and reduce environmental water quality. Therefore, reliable and robust sampling tools are required for monitoring pharmaceuticals. In this study, passive sampling devices of diffusive gradients in thin films (DGTs) were developed for sampling 35 pharmaceuticals in surface waters. The results demonstrated that hydrophilic-lipophilic balance (HLB) was more suitable for DGT-based devices compared with XAD18 and XDA1 resins. For most pharmaceuticals, the performance of the HLB-DGT devices were independent of pH (5.0-9.0), ionic strength (0.001-0.5 M), and flow velocity (0-400 rpm). The HLB-DGT devices exhibited linear pharmaceutical accumulation for 7 days, and time-weighted average concentrations provided by the HLB-DGT were comparable to those measured by conventional grab sampling. Compared to previous studies, we extended DGT monitoring to include three antiviral drugs used for COVID-19 treatment, which may inspire further exploration on identifying the effects of COVID-19 on ecological and human health.

Development of diffusive gradients in thin film technique for seasonal monitoring of benzophenone-type UV filters in coastal waters

Benzophenone(BP)-type UV filters are continuously released into various aquatic environments via the effluent discharge of wastewater treatment plants (WWTPs) and recreational activities in coastal beaches. In this study, we developed a robust and reliable sampling approach, diffusive gradients in thin-films (DGT), for seasonal monitoring of six BP derivatives in coastal waters to investigate their occurrence and environmental risk. The binding capacities of both XAD-2 and HLB gels for test BPs were over 252 μg with no significant deterioration in marine environment, suggesting that theoretically, DGT is capable of sampling for at least 3 months effectively. The diffusion coefficients of BPs in freshwater and seawater were determined for the first time. The sampling performance showed no dependence on environmental conditions including pH (4.0-8.5), ionic strength (0.0001-0.5 M) and dissolved organic matter (0-20 mg L^-1). The developed DGT samplers were successfully applied in a river estuary linked to a WWTP and a bathing beach at different periods of one year. Results showed that the concentrations of BPs in the coastal waters were dependent on seasonal variation. The highest level in summer and the ecological risk should be considered based on the risk quotient values. These results demonstrated that the present DGT method is suitable for measuring, characterization, and risk assessment of BPs in freshwater and marine environment.

Development of organic-diffusive gradients in thin films technique for measuring freely dissolved concentrations of tetracyclines using a commercial SPE packing

The freely dissolved concentrations (FDCs) of pollutants are related to their bioavailability in the environment, and the diffusive gradients in thin films technique (DGT) can obtain the FDC of an analyte. Aiming for the detection of the FDCs of tetracyclines (TCs), we used a polyacrylamide hydrogel comprising acrylamide and acrylaide agarose cross-linker as diffusive and binding gels, and a commercial solid-phase extraction (SPE) packing, namely polymer sorbent (PLS), as an adsorption material in the binding gel for the preparation of the organic-diffusive gradients in thin films (o-DGT) devices. The results showed that the diffusion coefficients of tetracycline (TC), oxytetracycline (OTC) and chlortetracycline (CTC) in the diffusive gels were 1.08 × 10-6, 1.08 × 10-6 and 1.03 × 10-6 cm2/ s at 25 °C, respectively. The binding gel showed excellent performance with adsorption capacities of 534.88-569.42 µg/disc for TC, 527.18-565.98 µg/disc for OTC and 1320.12-1320.86 µg/disc for CTC, respectively. The uptake efficiencies were 94.21-111.12, 71.25-88.44 and 76.10-86.62% for TC, OTC and CTC, respectively, with the TCs concentration of 0.05-10 mg/L. The adsorption kinetics of TCs could be described with a pseudo-second-order model (POSM, R2 >0.97). According to the result of adsorption kinetics, the adsorption rate of TCs in the binding gel was not as fast as that of heavy metals, suggesting that the TCs concentrations at the boundary of binding gels in the o-DGT devices could not decrease to zero. After correction of the boundary concentration, the FDCs accounted for 30.30-56.90, 48.10-64.68 and 16.55-50.16% for TC, OTC and CTC, respectively, while their concentrations ranged from 0.2 to 10.0 mg/L. Our results suggested that SPE packing might be an ideal adsorption material for o-DGT binding gels, and that adsorption kinetics should be corrected when calculating the FDCs of organic pollutants.

Determination of diffusion coefficients in agarose and polyacrylamide gels for 112 organic chemicals for passive sampling by organic Diffusive Gradients in Thin films (o-DGT)

The diffusive gradient in thin film technique was recently adapted to organic compounds. The diffusional coefficient (D) is a key parameter needed to calculate the time-weighted average concentration. In this study, two methods are used for D measurement in two gels (agarose and polyacrylamide): the diffusion cell method (D_cell) and the slice stacking method (D_stack). Thus, D were discussed and compared for 112 organic compounds, including pesticides, hormones, and pharmaceuticals. D_stack tends to be higher than D_cell. It could be explained by the presence of a non-negligible diffusive boundary layer thickness in diffusion cell. Consequently, the use of sampling rates (R_S) should be more adequate to determine water concentration, for a given bulk flow velocity. D_stack also corresponds to the diffusion in gel only, allowing the determination of the maximal R_S, and would be considered as a reference value that can be adjusted to in situ conditions, by applying the appropriate DBL thickness. The range and variability of D values found in the literature and obtained in this work were discussed. Relationships between D and compound physicochemical properties (molecular mass, log Dow, polar surface area, van der Waals volume) were investigated. We did not find clear and robust correlation between D and any single physicochemical property, for the set of compounds tested.

Remediation of noxious wastewater using nanohybrid adsorbent for preventing water pollution

Removal of toxic elements from wastewater effluent has got a lot of attention because of their severe negative effects on human and environmental health. In the past few years, rapid urbanization and industrial activities in developing countries have exacerbated the destruction of the environment. Most of the wastewater effluents are discharged untreated or inadequately treated, which has become a major concern due to its impact on sustainability and the environment. This is imperative to implement, innovative and resourceful wastewater treatment technologies requiring low investment. Among the various treatment technologies, cutting-edge processes in nano-material sciences have recently piqued the interest of scientists. Nanohybrid absorbents have the potential in improving wastewater treatment and increase water supply by utilizing unconventional water resources. Carbon nanotubes, titanium oxide, manganese oxide, activated carbon (AC), magnesium oxide, graphene, ferric oxides, and zinc oxide are examples of nano-adsorbents that are used to eliminate pollutants. This also demonstrated the effective removal of contaminants along with the harmful effects of chemicals, colorants, and metals found in wastewater. The present manuscript examines potential advances in nanotechnology in wastewater treatment for the prevention of water and soil pollution. This systematic review aims to highlight the importance of nanohybrid absorbents treatment technology for wastewater treatment and to explain how nanohybrid absorbents have the potential to revolutionize industrial pollution. There are also other published review articles on this topic but the present review covers an in-depth information on nano-adsorbents and their targeted contaminants.

In situ monitoring of phthalate esters (PAEs) pollution and environmental risk assessment in Poyang Lake Basin by DGT Technology using cyclodextrin polymer as binding phase

Poyang Lake is the first freshwater lake in China, which is an important drinking water source. In recent years, industrial pollution has led to the increased phthalate acid esters (PAEs) in Poyang Lake. PAEs are a class of typical endocrine disruptors that can accumulate in organisms and interfere with their secretion systems. Thus, the accurate determination of PAEs in Poyang Lake is important for health risk prediction and the development of corresponding control means. Monitoring organic pollutants in water using the diffusive gradient in thin films technique (DGT) has attracted much attention due to more accuracy and convenience than the traditional methods. This study used an inexpensive amphiphilic cyclodextrin polymer (PBCD) as the sorbent for the binding gel. This new binding gel has an ultra-high specific surface area and excellent adsorption performance. Diffusion coefficients of the five PAEs were determined, and the performance of DGT such as adsorption capacity and deployment time (1-4 days) was tested using five PAEs as models. The assembled PBCD-DGT was used to examine the performance in a complex simulated water environment. The sampling capability of PBCD-DGT was verified in Yangshan Lake, and a large-scale field application was conducted in Poyang Lake basin. The results of 11 sampling points showed that the concentration ranges of dimethyl phthalate, diethyl phthalate, diallyl phthalate, dipropyl phthalate, and dibutyl phthalate were 434-2594 ng/L, 40-314 ng/L, 80-527 ng/L, 45-308 ng/L, and ND-182 ng/L, respectively. The health risk index (HI) and ecological risk quotient (RQ) values of PAEs in the Poyang Lake watershed were far below 1, indictating a lower health and ecological risk. Considering that PAEs are bioaccumulative and persistent, it is very necessary to continue to pay attention to its pollution status and health and ecological risk changes in Poyang Lake Basin in the future.

Development and field evaluation of the organic-diffusive gradients in thin-films (o-DGT) passive water sampler for microcystins

The presence of microcystins (MCs) in waterbodies requires a simple and reliable monitoring technique to characterize better their spatiotemporal distribution and ecological risks. An organic-diffusive gradients in thin films (o-DGT) passive sampler based on polyacrylamide diffusive gel and hydrophilic-lipophilic balance (HLB) binding gel was developed for MCs in water. The mass accumulation of three MCs (MC-LR, -RR, and -YR) was linear over 10 days (R² ≥ 0.98). Sampling rates (2.68-3.22 mL d^-1) and diffusion coefficients (0.90-1.08 × 10^-6 cm² s^-1) of three MCs were obtained at 20 °C. Two different passive samplers, o-DGT and the Solid Phase Adsorption Toxin Tracking device (SPATT), were co-deployed to estimate MC levels at three lakes in California, USA. Measured total MC concentrations were up to 10.9 μg L^-1, with MC-LR the primary variant at a measured maximum concentration of 2.74 μg L^-1. Time-weighted average MC concentrations by o-DGT were lower than grab water samples, probably because grab sampling measures both dissolved and particulate phases (i.e., MCs in cyanobacteria). Passive water samplers by design can only measure dissolved-phase MCs, which are considerably less during the cyanobacteria-laden periods observed. Both o-DGT and grab samples gave comparable results for three MC variants at low levels of MCs, e.g., <0.1 μg L^-1. o-DGT showed a higher correlation with grab sampling than SPATT did. This study demonstrates that o-DGT can be effectively used for monitoring and evaluation of dissolved MCs in waters.

A critical review of diffusive gradients in thin films technique for measuring organic pollutants: Potential limitations, application to solid phases, and combination with bioassays

Diffusive gradient in thin films (DGT) for organics has received considerable attention for studying the chemical dynamics of various organic pollutants in the environment. This review investigates current limitations of DGT for organics and identifies several research gaps for future studies. The application of a protective outer filter membrane has been recommended for most DGT applications, however, important questions regarding longer lag times due to significant interaction or adsorption of specific groups of compounds on the outer membrane remain. A modified DGT configuration has been developed that uses the diffusive gel as the outer membrane without the use of an extra filter membrane, however use of this configuration, while largely successful, remains limited. Biofouling has been a concern when using DGT for metals; however, effect on the performance of DGT for organics needs to be systemically studied. Storage stability of compounds on intact DGT samplers has been assessed in select studies and that data is synthesized here. DGT has been used to describe the kinetic desorption of antibiotics from soils and biosolids based on the soil/biosolid physical-chemical characteristics, yet applications remain limited and requires further research before wide-scale adoption is recommended. Finally, DGT for organics has been rarely, albeit successfully, combined with bioassays as well as in vivo bioaccumulation studies in zebrafish. Studies using DGT combined with bioassays to predict the adverse effects of environmental mixtures on aquatic or terrestrial biota are discussed here and should be considered for future research.

Development and evaluation of a ceramic diffusive layer based DGT technique for measuring organic micropollutants in seawaters

Diffusive gradients in thin-films (DGT) technique has been well demonstrated as a robust tool for measuring organic micropollutants (OMPs) in the aquatic environment. However, potential adsorption of the OMPs on organic polymer filters and flow rate of waters can affect the measuring results of the DGT method, hence tedious work should be conducted to reduce these interferences. In the present study, a novel DGT technique coupled with a ceramic diffusive layer was developed to measure the OMPs in seawaters. The ceramic diffusive layer exhibited adsorption inertness to the OMPs with various logK_ow values. Moreover, the ceramic diffusive layer based DGT technique was proved to be less affected by the flow rate than the traditional DGT with agarose diffusive layer. The developed DGT device exhibited kinetic accumulation for the targets during a 6-d deployment, and measurement of the OMPs by the DGT method was independent with pH and ionic strength. Finally, the developed DGT sampler was applied in coastal waters of Dalian, and eight OMPs were detected with levels ranging from 1.58 to 13.1 ng/L. The development of the ceramic diffusive membrane can lead to simplification of the DGT applications, promoting the progress of the OMPs monitoring technology.

Selective diffusive gradients in thin-films with molecularly imprinted polymer for measuring fluoroquinolone antibiotics in waters

Fluoroquinolones (FQs) have raised significant concerns due to their ubiquitous occurrence and promoting of antimicrobial resistance (AMR). In this study, a molecularly imprinted polymer-diffusive gradient in thin-films (MIP-DGT) sampler is developed for selective measurement of FQs in waters by using a commercial available MIP material as the binding agent. The MIP-DGT shows selective adsorption of the FQs and linearly accumulates the FQs over the deployment time. MIP-DGT measurement is independent of pH (6-8) and ionic strength (IS) (0.01-0.5 M) but is affected by DOM at higher concentrations (~10 mg•L^-1), which is due to the altered diffusion coefficients and reduced adsorption on the MIP binding gel. Significant interaction effects of DOM with pH or IS indicate that this is the predominant influence on the MIP-DGT performance, which results in a lower measurement by the MIP-DGT but this is curtailed to some extend with increasing IS or pH. The MIP-DGT measurements, however, correlate well with those by grab sampling in a wastewater treatment plant, suggesting it is reliable for measuring FQs in waters. For the first time, we demonstrate that key water chemistry parameters do have interaction effects on the DGT measurements, which should be considered for the data interpretation. The MIP-DGT is a promising tool to understand the interaction effects of the environmental parameters on the fate, behaviours and bioavailability/toxicity of organic contaminants and improve environmental risk assessments in the environment and modelling.

Tetrafluoroterephthalonitrile-crosslinked β-cyclodextrin polymer as a binding agent of diffusive gradients in thin-films for sampling endocrine disrupting chemicals in water

β-Cyclodextrin (β-CD) is an inexpensive and reproducible material derived from corn starch. It is possible that tetrafluoroterephthalonitrile-crosslinked β-cyclodextrin polymer (TFN-CD), a cheap but efficient adsorbent, could be a suitable binding agent for use in the passive sampling technique, diffusive gradients in thin-films (DGT). Herein, the TFN-CD binding gel was prepared and then evaluated as the binding phase of DGT to sample six endocrine disrupting chemicals (EDCs) in water. The TFN-CD dispersed uniformly in the binding gel due to its hydrophilicity. The quantitative recoveries (99.3%-106%) of EDCs from the TFN-CD binding gel could be conveniently achieved by ultrasonic extraction using 5 mL methanol for 10 min. Compared with the excellent HLB (hydrophilic-lipophilic-balanced resin) binding gel, the TFN-CD binding gel had comparable or even faster adsorption kinetics, although the equilibrium adsorption capacity was slightly lower. The effective adsorption capacities of TFN-CD-based DGT (TFN-CD-DGT) were roughly estimated to enable a 7-days deployment in EDC solution of 25.7-30.0 μg L^-1. Studies of influencing factors showed that the ionic strength (0-0.5 M), pH (3.73-9.13), dissolved organic matter (0-20 mg L^-1) and long-term storage (204 days) had negligible influence on the performance of TFN-CD-DGT. Finally, the TFN-CD-DGT was successfully used to record sudden increases in bulk concentrations during simulated discharge events in pond water. These results demonstrate that TFN-CD is a suitable binding agent for sampling of EDCs, and the low cost of TFN-CD could be conducive to the application of DGT in large-scale sampling.

Development and application of diffusive gradients in thin-films for in situ sampling of the bitterest chemical - denatonium benzoate in waters

Denatonium benzoate (DB), a commonly used bitter agent in numerous products, has recently been recognized as a waterborne contaminant due to concern about its potential persistence, mobility and toxicity (PMT). However, its occurrence, levels and fate in global aquatic environments are largely unknown. In this study, a new sampling method, based on diffusive gradients in thin films (DGT) with mixed-mode cation exchange (MCX) as the binding agent, was developed for measuring DB in waters. MCX shows a rapid adsorption and high capacity for DB. DB is linearly accumulated by MCX-DGT. pH (6-8), ionic strength (0.01-0.5 M), or DOM (0-10 M) do not show any significant effect on the MCX-DGT performance, confirming its reliability. The DGT measurements in a wastewater treatment plant (WWTP) are comparable to those by paralleled grab sampling. The field results suggest DB is persistent in WWTPs and could be a potential domestic wastewater indicator. Therefore, MCX-DGT is a promising technique for understanding the environmental occurrence, levels and fate of DB. This is a first report of using DGT for DB monitoring and of DB occurrence in Chinese environments. Further exploration of DGT as a reliable passive monitoring tool for a wide range of PMT substances in different applications is warranted.

Field application of a novel active-passive sampling technique for the simultaneous measurement of a wide range of contaminants in water

A first test of the field capabilities of a novel in situ sampling technique combining active and passive sampling (APS) was conducted in the sea. The proof-of-concept device uses a pump to draw water into a diffusion cell where dissolved target substances are accumulated onto sorbents which are selective for different classes of contaminants (i.e., metal cations, polar and non-polar organic compounds), simultaneously. A controlled laminar flow established in the diffusion cell enables measurements of contaminant concentrations that are fully independent from the hydrodynamic conditions in the bulk solution. APS measurements were consistent with those obtained using conventional passive sampling techniques such as organic diffusive gradients in thin films (o-DGT) and silicone rubber (SR) samplers (generally < 40% difference), taking into account the prevailing hydrodynamic conditions. The use of performance reference compounds (PRC) for hydrophobic contaminants provided additional information. Field measurements of metal ions in seawater showed large variability due to issues related to the device configuration. An improved field set-up deployed in supplementary freshwater mesocosm experiments provided metal speciation data that was consistent with passive sampling measurements (DGT), taking into account the hydrodynamic conditions. Overall, the results indicate that the APS technique provides a promising approach for the determination of a wide range of contaminants simultaneously, and independently from the hydrodynamic conditions in the bulk solution.

Development and Applications of Novel DGT Passive Samplers for Measuring 12 Per- and Polyfluoroalkyl Substances in Natural Waters and Wastewaters

Extensive and long-term use of per- and polyfluoroalkyl substances (PFASs) has caused their widespread distribution in aquatic systems. A new diffusive gradients in thin-films (DGT) passive sampling method based on weak anion exchanger (WAX) binding layer is developed here for monitoring five perfluoroalkyl carboxylic acids (PFCAs), five perfluoroalkanesulfonic acids (PFSAs) and two PFASs (6:2 FTSA and GenX) in waters. Performance of WAX-DGTs was independent of environmental conditions, namely pH (3.03-8.96), ionic strength (1-500 mM), and DOM content (4-30 mg L^-1). Diffusion coefficients (D) of the 12 PFASs in the diffusive gels were measured, 9 for the first time. Linear correlations between D and perfluoroalkyl chain lengths (CF₂) were established to obtain D for congener chemicals with the similar functional group and structure. The binding capacity of the WAX-DGT sampler was at least 440 μg PFASs per sampler, sufficient for applications in waters across a wide range of conditions and PFASs concentrations. Successful applications of WAX based DGT samplers in a wastewater treatment plant (WWTP) and three rivers has demonstrated that DGT is a powerful tool for monitoring, surveillance and research of these 12 PFASs in aquatic systems, and can be extended to wider suites of PFs in future.

Field evaluation of diffusive gradients in thin-film passive samplers for wastewater-based epidemiology

There is a need for a simple water sampling technique to enable routine monitoring of community drug consumption through wastewater-based epidemiology (WBE). This study investigates the potential use of diffusive gradients in thin films to sample organic compounds (o-DGT) for WBE. Three types of resin gels (HLB, XAD 18, and XDA-1) within o-DGT samplers each were deployed in triplicate at the inlets of two sewage treatment plants of Southern Asian cities. The target compounds included 15 illicit drugs and 18 antibiotics. A comprehensive evaluation was undertaken regarding each resin's ability to accumulate the target compounds and accuracy by comparing active samples. The organic compounds accumulated on each resin gel were characterised at the molecular level using Fourier transform ion-cyclotron-resonance mass spectrometry (FT-ICR MS). The results showed that the HLB resin performed better than the XAD 18 and XDA-1 resins. Based on calculations using the HLB-DGT data, methamphetamine and heroin were the two most popular illicit drugs consumed among the studied populations, and were followed by ketamine and codeine, which agreed well with the authoritative reports and reference data. The total drug consumption in Hanoi was one order of magnitude higher than that in Guangzhou, thus implying a probably more serious drug situation in the former. Overall, the findings of this study demonstrate that o-DGT passive samplers are a promising tool for WBE studies, particularly at WWTPs or in urban streams where an automatic sampler for taking composite water samples is absent.

Limitations of Integrative Passive Samplers as a Tool for the Quantification of Pharmaceuticals in the Environment - A Critical Review with the Latest Innovations

This review starts with a presentation of the theory of kinetic uptake by passive sampling (PS), which is traditionally used to distinguish between integrative and equilibrium samplers. Demonstrated limitations of this model for the passive sampling of pharmaceuticals from water were presented. Most notably, the contribution of the protective membrane in the resistance to mass transfer of lipophilic analytes and the well documented effect of external parameters on sampling rates contributed to the greatest uncertainty in PS application. The diffusion gradient in thin layer (DGT) technique seems to reduce the effect of external parameters (e.g., flow rate) to some degree. The laboratory-determined integrative uptake periods over defined sampler deployments was compared, and the discrepancy found suggests that the most popular Polar Organic Chemical Integrative Sampler (POCIS) could in some cases utilized as an equilibrium sampler. This assertion is supported by own calculations for three pharmaceuticals with extremely different lipophilic characters. Finally, the reasons performance reference compounds (PRCs) are not recommended for the reduction in uncertainty of the TWAC found by adsorptive samplers were presented. It was concluded that techniques of passive sampling of pharmaceuticals need a new uptake model to fit the current situation.

Calibration of organic-diffusive gradients in thin films (o-DGT) passive samplers for perfluorinated alkyl acids in water

The application of the organic-diffusive gradients in thin films (o-DGT) passive sampling technique for the monitoring of per- and polyfluoroalkyl substances (PFAS) in the environment is still limited. Six common PFAS with different chain lengths were evaluated in water by o-DGT. Measured diffusion coefficients (D) in agarose and polyacrylamide diffusive gels ranged from 4.55-8.63 × 10^-6 cm² s^-1 and 3.85-7.00 × 10^-6 cm² s^-1 at 23 °C, respectively. Experimental sampling rates (Rs) for both agarose- and polyacrylamide-WAX sampler configurations were within 22% relative error of D-based Rs for four of the PFAS. Larger differences for perfluorobutanesulfonic acid (PFBS) and perfluoroundecanoic acid (PFUnDA) ranged from 36% to 56%. In general, in-situ Rs can be predicted using measured D-values for perfluorinated alkyl acids. The mass accumulation of six PFAS in two o-DGT configurations was linear over 21 days (R² ≥ 0.97). Diffusion and uptake of o-DGT depended on the gel type and specific PFAS. Field demonstrations of o-DGT with WAX and HLB binding gels and polyacrylamide diffusive gels (not prone to biodegradation) found 0.3-19.5 ng L^-1 of PFAS in rivers near industrial areas around Guangzhou and Foshan, China, with no apparent differences between the two co-deployed samplers. This study demonstrates that the configurations of o-DGT tested provide a cost-effective monitoring tool for measuring perfluorinated alkyl acids in aquatic systems, in particular the four PFAS for which reasonable correlations were observed.

Direct Measurement of Aqueous Mercury(II): Combining DNA-Based Sensing with Diffusive Gradients in Thin Films

A highly specific DNA-functionalized hydrogel sensing layer was integrated with the diffusive gradients in thin films (DGT) technique for the direct determination of aqueous mercury(II). The DNA-functionalized layer in the DGT unit exhibited both high affinity (complexation constant K_c = 10^19.8 at 25 °C) and high binding capacity (9.5 mg Hg disk^-1) toward Hg²⁺. The diffusion coefficient for Hg²⁺ complexed with common inorganic ligands was an order of magnitude higher than that for Hg²⁺ complexed with natural dissolved organic matter: 9.0 × 10^-6 versus 9.8 × 10^-7 cm² s^-1 at 25 °C. The performance of the DNA-DGT sensor was further assessed under variable pH (3-10) and temperature (5-40 °C) conditions, as well as across a range of hydrochemically diverse artificial and natural freshwaters. The observed effects of the environmental and solution compositional variables on Hg²⁺ binding to the DNA in the sensing layer were successfully accounted for by equilibrium speciation calculations and temperature-corrected, multicomponent diffusion coefficients for aqueous Hg(II). The results therefore support the use of the DNA-DGT sensor as an alternative to traditional sampling and analysis methods for measuring aqueous Hg(II) concentrations down to the nanomolar level in freshwater environments.

In situ measurement of synthetic musks in wastewaters using diffusive gradients in thin film technique

Synthetic musks (SMs) are used extensively in household and personal care products and have acted significant concerns due to their environmental impacts and potential health effects. Here, we present a passive sampling approach based on diffusive gradients in thin films (DGT) for in situ measurement of SMs in urban wastewaters. XAD-2 binding gel, which has a rapid binding rate and high elution efficiency, was used in DGT device for the accumulation of six polycyclic musks and three nitro musks. The diffusion coefficients (D and D_NL) of the SMs through agarose gel without and with a nylon filter membrane were 3.37-4.49 and 1.48-4.41 ×10^-6cm² s^-1. The filter membrane caused an ~3 h lag phase and slowed the diffusion rates of the SMs through the diffusive phase. Solution pH (4.30-8.92), ionic strength (0.0001-0.5 M) and dissolved organic matter (0-20 mg L^-1) showed no obvious influence on uptake of the SMs in DGT. The measured average SM concentrations in the effluent of wastewater treatment plants ranged from 0.45-696 ng/L for DGT deployment, without obvious membrane biofouling, and they were comparable to the concentrations determined by grab sampling. These results confirmed that the present method is reliable and convenient for in situ measurement of semivolatile hydrophobic SMs in complicated waters and is an available tool to investigate the environmental behaviors of SMs in the environment.

A year-long passive sampling of phenolic endocrine disrupting chemicals in the East River, South China

The occurrence of endocrine disrupting chemicals (EDCs) in the aquatic environment is a global concern. In this study, we employed two different passive samplers Diffusive Gradients in Thin-films (DGT) and Chemcatcher for in situ measurement of 8 phenolic EDCs in the East River of the Pearl River system over one-year. These data were assessed alongside results from traditional grab sampling. Six chemicals (4tOP, 4NP, BPA, E1, EE2 and DES) were regularly detected in the water samples, of which the three phenols (i.e. 4tOP, 4NP and BPA) were in all samples and at high concentrations (0.4-1040 ng/L for 4tOP, 2.6-58500 ng/L for NP and 11.4-123300 ng/L for BPA). Fewer target chemicals were detected in both passive samplers, with only 4tOP, 4NP and BPA found in most samplers; E1 and DES were occasionally measurable above detection limits. The higher (by about a factor of 2-3) measurements provided by DGT compared to Chemcatcher could be attributed to the effect of the diffusive boundary layer on Chemcatcher uptake or the strong adsorption of target chemicals on the Chemcatcher PES filter. The temporal trends of EDC monthly loadings indicated that they were from different sources and that WWTPs were not effective in EDC removal and/or there was still some untreated wastewater discharged into the rivers.

Heavy Metals in Wastewater and Sewage Sludge from Selected Municipal Treatment Plants in Eastern Cape Province, South Africa

This study assessed the distribution of five heavy metals (Cd, Pb, Cu, Zn, and Fe) across the various stages of treatment in three selected sewage treatment facilities and their receiving waterbodies in the Eastern Cape Province, South Africa. Aqueous and solid (sludge) samples were collected monthly from September 2015 to February 2016. Quantitation was achieved by atomic absorption spectrometry after necessary sample preparations. Concentrations of heavy metal cations in the sludge generally varied from <DL (below detection limit) to 1.17 mg kg−1, <DL to 0.14 mg kg−1, 27.588 to 69.789 mg kg−1, and <DL to 0.099 mg kg−1 for Cu, Cd, Fe and Pb; while Zn was below detection all through. Similarly, the levels of Cu, Cd, and Fe in the influents, effluents, upstream and downstream across the three plants ranged from <DL–6.588 mg L−1, <DL–0.636 mg L−1, <DL–0.878 mg L−1 and <DL–0.711 mg L−1, respectively; Zn and Pb were less than DL in all the matrices and study locations. All the contaminants were below hazardous levels in all the sludge and aqueous samples except Cd which was higher in effluents and surface waters across the board. Wastewater Treatment Plant (WWTP)-A exhibited better removal capacity for Fe (86.6%), compared to WWTP-B (34.7%) and WWTP-C (56.9%). However, the removal of Cu and Zn was very poor in all the treatment facilities studied. Carcinogenic and non-carcinogenic risks evaluated were sufficiently low. This suggests that the levels of contamination, even with respect to Cd, was minimal. Nevertheless, efforts should be made to keep the concentrations of these contaminants at levels safe for humans and aquatic organisms. Furthermore, the use of the effluents from these facilities for irrigation should be discouraged to prevent unnecessary build-up of metals in the soil and plants grown with such, as well as subsequent bioaccumulation and biomagnification in the food chain.

In Situ Catchment Scale Sampling of Emerging Contaminants Using Diffusive Gradients in Thin Films (DGT) and Traditional Grab Sampling: A Case Study of the River Thames, UK

The in situ passive sampling technique, diffusive gradients in thin films (DGT), confronts many of the challenges associated with current sampling methods used for emerging contaminants (ECs) in aquatic systems. This study compared DGT and grab sampling for their suitability to screen and monitor ECs at the catchment scale in the River Thames system (U.K.) and explored their sources and environmental fate. The ubiquitous presence of endocrine disrupting chemicals, parabens, and their metabolites is of concern. This study is the first to report organophosphate esters (OPEs) in the study area. TEP (summer 13-160 and winter 18-46, ng/L) and TCPP (summer 242-4282 and winter 215-854, ng/L) were the main OPEs. For chemicals which were relatively stable in the rivers, DGT and grab sampling were in good agreement. For chemicals which showed high variation in water bodies, DGT provided a better integral of loadings and exposure than grab sampling. DGT was not as sensitive as grab sampling under the procedures employed here, but there are several options to improve it to give comparable/better performance. DGT samples require shorter preparation time for analysis in the laboratory than grab samples. Overall, DGT can be a powerful tool to characterize ECs throughout a large dynamic water system.

Monitoring Organic Pollutants in Waters Using the Diffusive Gradients in the Thin Films Technique: Investigations on the Effects of Biofouling and Degradation

The diffusive gradients in thin films (DGT) passive sampling technique has been increasingly used to provide time-weighted average concentrations of the biorelevant fraction of organic contaminants in waters, with high spatial and temporal resolutions at low cost. This study was tested for the effects of biofouling and compound degradation/loss during sample handling/storage on the DGT measurement of a range of emerging organic pollutants. Biofouling was tested using biofilms collected from the influent and effluent of a typical urban wastewater treatment plant. Most (85%) target compounds showed no detectable effect on the DGT measurement when 8- and 15-day biofouled membrane filters were used. Four storage methods were designed to test for within-sampler degradation/loss for up to 2 months. Intact samplers can be simply stored in polyethylene bags at ambient temperature (18-26 °C) with most compounds stable (mass loss <20%) for at least 1 week. Keeping intact samplers at 4 °C or binding gels in solvent gave good recoveries, with most chemicals being stable for up to 2 months, although the best results were obtained when binding gels were kept in solvent at 4 °C. Recommendations are made for sample handling and storage of DGT samplers used for determination of trace organics in monitoring and surveillance campaigns.

Performance of the organic-diffusive gradients in thin-films passive sampler for measurement of target and suspect wastewater contaminants

Although passive sampling is widely accepted as an excellent tool for environmental monitoring, their integration with suspect or non-targeted screening by high-resolution mass spectrometry has been limited. This study describes the application of the organic-diffusive gradients in thin-films (o-DGT) passive sampler as a tool for accurate measurement of both targeted and suspect polar organic contaminants (primarily pharmaceuticals) in wastewater. First, performance of o-DGT was assessed alongside the polar organic chemical integrative sampler (POCIS) and active sampling at two wastewater treatment facilities using targeted analyses. Overall, water concentrations measured by o-DGT, POCIS, and 24-hr integrative active samples were in good agreement with each other. There were exceptions, including a systematic difference between o-DGT and POCIS at certain sites that we propose was a result of site-specific conditions and a difference in sampling rates between the two techniques. The second component of this work involved suspect screening of the o-DGT extracts using high-resolution, high mass accuracy quadrupole time-of-flight mass spectrometry (QTOF). Lamotrigine, venlafaxine, and des-methylvenlafaxine were three suspect compounds identified and selected as proof-of-concept case studies to determine the feasibility and accuracy of o-DGT for estimating water concentrations based upon predicted sampling rates using a previously validated o-DGT diffusion model. Semi-quantification of the suspect compounds was conducting using an average surrogate response factor based on the suite of compounds measured by the targeted analyses. This, combined with the modelled sampling rates provided time-weighted average wastewater concentrations of the identified suspects within a factor of 2 of the true value, confirmed by isotope dilution with mass labelled internal surrogates. To the knowledge of the authors, this work is the first to demonstrate the utility of the o-DGT passive sampler as a potential environmental screening tool that can be integrated into the rapidly advancing field of non-targeted high resolution mass spectrometry.

Diffusion coefficients of polar organic compounds in agarose hydrogel and water and their use for estimating uptake in passive samplers

Diffusion coefficient (D) is an important parameter for prediction of micropollutant uptake kinetics in passive samplers. Passive samplers are nowadays commonly used for monitoring trace organic pollutants in different environmental matrices. Samplers utilising a hydrogel layer to control compound diffusion are gaining popularity. In this work we investigated diffusion of several perfluoroalkyl substances, currently used pesticides, pharmaceuticals and personal care products in 1.5% agarose hydrogel by measuring diffusion coefficients using two methods: a diffusion cell and a sheet stacking technique. Further, diffusion coefficients in water were measured using Taylor dispersion method. The sheet stacking method was used to measure D at 5, 12, 24, and 33 °C in order to investigate temperature effect on diffusion. Median D values ranged from 2.0 to 8.6 × 10^-6 cm² s^-1 and from 2.1 to 8.5 × 10^-6 cm² s^-1 for the diffusion cell and sheet stack methods respectively. For most compounds, the variability between replicates was higher than the difference between values obtained by the two methods. Rising temperature from 10 to 20 °C increases the diffusion rate by the factor of 1.41 ± 0.10 in average. In water, average D values ranged from 3.03 to 10.0 × 10^-6 cm² s^-1 and were comparable to values in hydrogel, but some compounds including perfluoroalkyl substances with a long aliphatic chain could not be evaluated properly due to sorptive interactions with capillary walls in the Taylor dispersion method. Sampling rates estimated using the measured D values were systematically higher than values estimated from laboratory sampler calibration in our previously published study, by the factor of 2.2 ± 1.0 in average.