Enhanced Swelling and Responsive Properties of Pineapple Peel Carboxymethyl Cellulose-g-poly(acrylic acid-co-acrylamide) Superabsorbent Hydrogel by the Introduction of Carclazyte

Fabrication of carboxymethyl cellulose/graphene oxide/ZnO composite hydrogel for efficient removal of fuchsin dye from aqueous media

Hydrogels are hydrophilic, insoluble, and highly porous 3D networks capable of absorbing large amounts of water. This study aimed to develop a carboxymethyl cellulose/graphene oxide (CMC/GO) hydrogel, cross-linked with citric acid and modified with zinc oxide (ZnO) nanoparticles (CMC/GO/ZnO), synthesized via the sol-gel method. The formulated composite hydrogel samples were characterized by Fourier transmittance infrared spectroscopy (FTIR), scanning electron microscopy (SEM) analysis, X-ray diffraction (XRD), transmission electron microscopy (TEM), and thermo-gravimetric analysis (TGA). The hydrogels were tested for the adsorption of basic fuchsin (BF) dye from the aqueous medium under various conditions, such as adsorbent dosage, contact time, pH, and temperature, using batch adsorption. The adsorption data best fit the Langmuir and Temkin models, with maximum adsorption capacity (qmax) of 172.41 mg/g for CMC/GO and 303.03 mg/g for CMC/GO/ZnO. Optimal adsorption occurred at pH = 6 and within 30 min. The process followed a pseudo-second-order kinetic model, and thermodynamic results indicated that the adsorption process is physical, endothermic and spontaneous. The COOH groups in the hydrogels enhanced affinity for cationic dyes through hydrogen bonding and electrostatic interactions. Thus, CMC/GO and CMC/GO/ZnO hydrogels are efficient and promising adsorbents for environmental remediation.

pH-sensitive semi-interpenetrating network of microcrystalline cellulose and methacrylic acid hydrogel for the oral delivery of insulin

Insulin is commonly administered to diabetic patients subcutaneously and has shown poor patient compliance. Due to this, research has been carried out extensively to find molecules that could deliver insulin orally. In this context, a new type of pH-responsive hydrogel, composed of microcrystalline cellulose and methacrylic acid-based hydrogels, has been developed and studied for the oral delivery of insulin. These hydrogels were prepared by free radical polymerization using potassium persulphate as initiator and N, N'-methylenebisacrylamide as a cross-linker. These pH-sensitive hydrogels showed swelling in distilled water as high as 5800 %. The hydrogels were investigated for swelling in saline and glucose solutions, and pH sensitivity was confirmed by swelling in solutions of different pH. The morphological shape was established by SEM, and the structure was analyzed by FTIR. Thermal degradation was investigated by TGA. In vitro release studies have confirmed pH sensitivity, showing lower insulin release at pH 1.2 than at pH 6.8. The encapsulation efficiency was determined to be 56.00 ± 0.04 %. It was further validated by in-vivo investigations for which insulin was loaded into hydrogels and administered orally to healthy and diabetic Wistar rats at 40 IU/kg, showing maximum hypoglycemic effect at 6 h, which was sustained for 24 h. In the stomach's acidic environment, the gels remained unaffected due to the formation of intermolecular polymer complexes. Insulin remained in the gel and was protected from proteolytic degradation. Thus, pH-responsive methacrylic acid-based hydrogels are promising for biomedical applications, especially oral drug delivery.

Effect of chain structures of monomer on hydroxyethyl cellulose-based superabsorbent properties and improvement of chickpeas plant growth of water deficit-stressed

The aim of this research was evaluation of the influence of distance between zwitterionic monomer ions on the performance of superabsorbents. For this purpose, two zwitterionic monomers 4-(3-aminopropyl) amino-4-oxo-2-butenoic acid (APOB) and 4-(6-aminohexyl) amino-4-oxo-2-butenoic acid (AHOB) were prepared and applied for synthesis of two new superabsorbents through graft copolymerization onto hydroxyethyl cellulose (HEC) in the presence of acrylic acid (AA). In synthesis of superabsorbents factors such as the highest water absorbency capacity, absorbency rate, gel strength, and environmental problems should be resolved or improved. The results demonstrated that the water absorbency capacity and rate parameters (τ) of HEC-g-p(AA-co-APOB) and HEC-g-p(AA-co-AHOB) in distilled water were 986.62, 664.38 g/g, and 98.04, 140.84 min, respectively. The biodegradability of HEC-g-p(AA-co-APOB) was approximately 4 times more than HEC-g-p(AA-co-AHOB). However, based on the rheological analyses (G'/G″) HEC-g-p(AA-co-AHOB) was stronger than the other. Additionally, studies of water retention on soil containing HEC-g-p(AA-co-AHOB) superabsorbent (soil with 0.25 wt% material) showed that the after 30 days has ≤5 % water while soil in the absence of superabsorbent after 10 days completely dried. Studies of the growth of plants in soil demonstrated in the presence of HEC-g-p(AA-co-AHOB) the average length of shoots was 36 cm while without superabsorbent were 25 cm.

Preparation of CMC-poly(N-isopropylacrylamide) semi-interpenetrating hydrogel with temperature-sensitivity for water retention

The CMC-PNIPAM hydrogel with semi-interpenetrating structure and temperature-sensitivity was prepared by in-situ polymerization of N-isopropylacrylamide (NIPAM) in sodium carboxymethylcellulose (CMC) solution at room temperature. The mass ratio of CMC to NIPAM was a key factor influencing the network structure and property of CMC-PNIPAM hydrogel. The low critical phase transition temperature (LCST) of CMC-PNIPAM hydrogels increased from 34.4 °C to 35.8 °C with the mass ratio of CMC to NIPAM rising from 0 to 1.2. The maximum compressive stress of CMC-PNIPAM hydrogel reached to 26.7 kPa and the relaxation elasticity was 52 % at strain of 60 %. The viscoelasticity of CMC-PNIPAM hydrogel was consistent with the generalized Maxwell model. The maximum swelling ratio in deionized water was 170.25 g·g-1 (dried hydrogel) with swelling rate of 2.57 g·g-1·min-1 at 25 °C. CMC-PNIPAM hydrogel hardly absorbed water above LCST, but the swollen hydrogel could release water at the rate of 0.36 g·g-1·min-1 once exceeding LCST. The test of water retention showed that soil mixed with 2 wt% dried CMC-PNIPAM hydrogel could retain 13.08 wt% water after 30 days at 25 °C that was 4.4 times than that of controlled soil without CMC-PNIPAM hydrogel. The semi-interpenetrating CMC-PNIPAM hydrogel showed a potential to conserve water responding to temperature.

A comprehensive assessment of superabsorbent resin produced using modified quinoa husk and coal fly ash - Preparation, characterization and application

About 200 million tons of coal fly ash (CFA) is not effectively used in China every year. To enhance the utilization of biomass waste quinoa husk (QH) and solid waste CFA and reduce the preparation cost of superabsorbent resin (SAR), a low-cost, biodegradable modified quinoa husk-g-poly (acrylic acid)/coal fly ash superabsorbent resin (MQH-g-PAA/CFA SAR) was synthesized using modified quinoa husk (MQH), acrylic acid and CFA and used to improve the drought resistance and fertilizer conservation ability of soil. The surface morphology and performance of SAR were characterized by Fourier transform infrared (FTIR) spectrometry, scanning electron microscopy (SEM), and thermogravimetric analysis (TGA), which provided evidence for improving the properties of SAR by grafting MQH and adding CFA. In addition, the synthesis conditions were studied and optimized, together with the contents of initiator, crosslinker, MQH, and CFA to acrylic acid as well as the neutralization degree of acrylic acid. After optimization, the optimum water absorbency of SAR in deionized water, tap water, and physiological saline was 1302, 356, and 91 g/g respectively. The swelling and water-retention mechanisms of SARs were analyzed by a dynamic model and the results were in good agreement with the experimental data. In the soil experiment, the addition of SAR improved the drought resistance ability of soil, and reduced the leaching loss of fertilizer in the soil (from 49.5 % to 36.7 %). Therefore, this material exhibits significant potential in the field of agriculture and offers a novel approach with economic benefit for the utilization of MQH and CFA.

One-step synthesis of phospho-rich, silica-enhanced chitosan aerogel for the efficient adsorption of uranium(VI)

In this study, an amorphous silica reinforced, phosphoric-crosslinked chitosan foam (P-CTS@SixOy) was prepared. The introduction of amorphous silica not only increased the affinity of the adsorbent for uranium, but also improved the stability of the material. The number of active sites of P-CTS@SixOy was increased by the introduction of phosphate groups. The material exhibited excellent uranium adsorption performance with the removal capacity and efficiency of 850.5 mg g-1 and 98.1 %, respectively. After regenerations, the morphology of P-CTS@SixOy still maintained, and the uranium adsorption efficiency remained above 90 %, manifesting the excellent cycle performance of P-CTS@SixOy. In the dynamic adsorption experiment, P-CTS@SixOy successfully concentrated the volume of uranium-containing solution, and exhibited excellent uranium adsorption performance. The analysis of kinetics, isotherms, and thermodynamics manifested that the uranium adsorption behavior of P-CTS@SixOy was a spontaneous, endothermic, monolayer chemical adsorption process. X-ray photoelectron spectroscopy, Scanning Electron Microscope, and Fourier Transform Infrared Spectrometer were used to characterized the P-CTS@SixOy before and after adsorption, which demonstrated that the main interaction mechanism between uranium and P-CTS@SixOy was the complexation. These studies indicated the huge application prospect of P-CTS@SixOy in the treatment of large-scale uranium-containing wastewater.

Biotechnological innovations in nanocellulose production from waste biomass with a focus on pineapple waste

New materials' synthesis and utilization have shown many critical challenges in healthcare and other industrial sectors as most of these materials are directly or indirectly developed from fossil fuel resources. Environmental regulations and sustainability concepts have promoted the use of natural compounds with unique structures and properties that can be biodegradable, biocompatible, and eco-friendly. In this context, nanocellulose (NC) utility in different sectors and industries is reported due to their unique properties including biocompatibility and antimicrobial characteristics. The bacterial nanocellulose (BNC)-based materials have been synthesized by bacterial cells and extracted from plant waste materials including pineapple plant waste biomass. These materials have been utilized in the form of nanofibers and nanocrystals. These materials are found to have excellent surface properties, low density, and good transparency, and are rich in hydroxyl groups for their modifications to other useful products. These materials are well utilized in different sectors including biomedical or health care centres, nanocomposite materials, supercapacitors, and polymer matrix production. This review explores different approaches for NC production from pineapple waste residues using biotechnological interventions, approaches for their modification, and wider applications in different sectors. Recent technological developments in NC production by enzymatic treatment are critically discussed. The utilization of pineapple waste-derived NC from a bioeconomic perspective is summarized in the paper. The chemical composition and properties of nanocellulose extracted from pineapple waste may have unique characteristics compared to other sources. Pineapple waste for nanocellulose production aligns with the principles of sustainability, waste reduction, and innovation, making it a promising and novel approach in the field of nanocellulose materials.

Superabsorbent hydrogels based on natural polysaccharides: Classification, synthesis, physicochemical properties, and agronomic efficacy under abiotic stress conditions: A review

Superabsorbent polymers (SAPs) are a class of polymers that have attracted tremendous interest due to their multifunctional properties and wide range of applications. The importance of this class of polymers is highlighted by the large number of publications, including articles and patents, dealing with the use of SAPs for various applications. Within this framework, this review provides an overview of SAPs and highlights various key aspects, such as their history, classification, and preparation methods, including those related to chemically or physically cross-linked networks, as well as key factors affecting their performance in terms of water absorption and storage. This review also examines the potential use of polysaccharides-based SAPs in agriculture as soil conditioners or slow-release fertilizers. The basic aspects of SAPs, and methods of chemical modification of polysaccharides are presented and guidelines for the preparation of hydrogels are given. The water retention and swelling mechanisms are discussed in light of some mathematical empirical models. The nutrient slow-release kinetics of nutrient-rich SAPs are also examined on the basic of commonly used mathematical models. Some examples illustrating the advantages of using SAPs in agriculture as soil conditioners and agrochemical carriers to improve crop growth and productivity are presented and discussed. This review also attempts to provide an overview of the role of SAPs in mitigating the adverse effects of various abiotic stresses, such as heavy metals, salinity, and drought, and outlines future trends and prospects.

Valorization of waste biomass for synthesis of carboxy-methyl-cellulose as a sustainable edible coating on fruits: A review

The coating on fruits and vegetables increases the shelf-life by providing protection against their spoilage. The existing petroleum-based coating materials have considerable health threats. Edible coating materials prepared with the cellulose derivative extracted from the waste biomass could be a sustainable alternative and environment friendly process to increase the shelf-life periods of the post-harvest crops. Selection of suitable waste biomass and extraction of cellulose are the critical steps for the synthesis of cellulose-based edible film. Conversion of extracted cellulose into cellulosic macromolecular derivatives such as carboxy-methyl-cellulose (CMC) is vital for synthesizing edible coating formulation. Applications of sophisticated tools and methods for the characterization of the coated fruits would be helpful to determine the efficiency of the coating material. In this review, we focused on: i) criteria for the selection of suitable waste biomass for extraction of cellulose, ii) pretreatment and extraction process of cellulose from the different waste biomasses, iii) synthesis processes of CMC by using extracted cellulose, iv) characterizations of CMC as food coating materials, v) various formulation techniques for the synthesis of the CMC based food coating materials and vi) the parameters which are used to evaluate the shelf-life performance of different coated fruits.

Cellulosic wastepaper modified starch/ itaconic acid/ acrylic acid-based biodegradable hydrogel as a sustain release of NPK fertilizer vehicle for agricultural applications

In this work, wastepaper powder was used as a modifying agent for a biodegradable hydrogel composite of starch, itaconic acid, and acrylic acid. After the addition of an optimum amount of the modifying agent, the swelling ability of the hydrogel was enhanced from 503 g/g to 647 g/g. Further, the hydrogel was also used for sustained release of NPK fertilizer and subsequent effect of the fertilizer loaded hydrogel in okra seed germination was also studied. The NPK loaded-hydrogel showed good sustained-release behavior and 98 % of N, 81 % of P and 95 % of K release were observed after 20th day of incubation. Moreover, the release study was explained by using different kinetic models. In seed germination study, a higher and faster germination rate for okra seeds was observed in case of NPK loaded hydrogel compared to the control system, which was attributed to the synergistic effect of essential macronutrients (N, P, and K) and water that were inside the hydrogel. Most importantly, the hydrogel was found to be biodegradable by using soil burial method and further confirmed by FTIR and SEM analyses. Thus, this work provides an efficient way for utilization of wastepaper in the production of a biodegradable hydrogel for agricultural applications.

Insight into adsorption process and mechanisms of Cr(III) using carboxymethyl cellulose-g-poly(acrylic acid-co-acrylamide)/attapulgite composite hydrogel

Cr(III) as one of the most concerned potentially toxic elements, is discharged from relevant industries and Cr(VI) reduction. Hydrogel-based adsorption could be one of the promising approaches for Cr(III) removal. Featured with environmental friendliness and low cost, carboxymethyl cellulose (CMC) was employed for the hydrogel synthesis, and attapulgite (APT) could be used to strengthen its stability. However, the adsorption performance and mechanisms need to be examined. In the present study, carboxymethyl cellulose-g-poly(acrylic acid-co-acrylamide)/ attapulgite (CMC-g-p(AA-co-AM)/APT) was synthesised via in situ copolymerisation. Its efficacy for removing Cr(III) from an aqueous solution was investigated using batch adsorption experiments. Results showed that the introduction of APT enhanced the thermal stability but decreased the swelling performance of the hydrogel. The prepared hydrogel could strongly adsorb Cr(III) at a wide pH range of 3.0-7.0. Cr(III) can be efficiently removed by the composite hydrogel within 1-2 h. At low concentration, CMC-g-p(AA-co-AM)/APT could slightly adsorbed more Cr(III) than CMC-g-p(AA-co-AM). The maximum absorption of CMC-g-p(AA-co-AM) and CMC-g-p(AA-co-AM)/APT were 74.8 and 47.7 mg/g at 298 K, respectively. The negative value of ΔHo and ΔGo indicated the adsorption of Cr(III) onto the two studied hydrogels is an exothermic and spontaneous process. Ion exchange and complexation, as implied by EDS, FT-IR and XPS, combining with electrostatic attraction are the possible adsorption mechanisms for Cr(III) onto the prepared hydrogels. All the results above suggests that the composite hydrogel CMC-g-p(AA-co-AM)/APT can be a promising candidate for the removal of Cr(III) from waste water.

Highly Flexible, Self-Bonding, Self-Healing, and Conductive Soft Pressure Sensors Based on Dicarboxylic Cellulose Nanofiber Hydrogels

Conductive hydrogels have gained a great deal of interest in the flexible electronics industry because of their remarkable inherent properties. However, a significant challenge remains for balancing hydrogel's conductivity, self-healing, and strength properties. Herein, double network ionic hydrogels were fabricated by concurrently introducing borax into dicarboxylic cellulose nanofiber (DCNFs) and polyacrylamide (PAM) hydrogels. The incorporation of borax provided a superabsorbent feature to the PAM/DCNF hydrogels (without borax) with the equilibrium water absorption rate increased from 552 to 1800% after 42 h. The compressive strength of the prepared hydrogel was 935 kPa compared to 132 kPa for the PAM hydrogel, with high cycling stability (stable after 1000 compression cycles with 50% strain). The hydrogel pressure sensor had a very sensitive response (gauge factor = 1.36) in the strain range from 10 to 80%, which made it possible to detect mechanical motion accurately and reliably. The developed hydrogels with high-performance, environmentally friendly properties are promising for use in future artificial skin and human-machine interface applications.

Curcumin-loaded Butea monosperma gum-based hydrogel: A new excipient for controlled drug delivery and anti-bacterial applications

The wide spectrum of applications provided by curcumin has attracted researchers worldwide to identify its molecular targets and employ it in various biomedical applications. The present research work focuses on the development of a Butea monosperma gum-based hydrogel encapsulated with curcumin and further employing it for two diverse applications, i.e., drug delivery and anti-bacterial application. A central composite design was utilized for the optimization of significant process variables to achieve maximum swelling. A maximum of 662 % swelling was attained at the initiator (0.06 g), monomer (3 ml), crosslinker (0.08 g), solvent (14 ml), and time (60 s). Furthermore, the characterization of the synthesized hydrogel was performed via FTIR, SEM, TGA, H1-NMR, and XRD analysis. Various important properties like swelling rate under different solutions, water retention capacity, re-swelling capability, porosity, and density measurement suggested that the prepared hydrogel exhibited a highly stable crosslinked network with high porosity (0.23) and density (62.5 g/cm³) values. The encapsulation efficiency of curcumin in the hydrogel was reported to be 93 % and 87.3 %, respectively, wherein BM-g-poly(AA) ~ Cur exhibited excellent sustained pH-responsive site release of curcumin at two different pH values, with the maximum amount of release taking place at pH 7.4 (792 ppm) and a minimum at pH 5 (550 ppm) due to the lesser ionization of the functional groups present in the hydrogel at a lower pH value. Additionally, the results from the pH shock studies indicated our material to be stable and efficient even with fluctuations in pH, resulting in the optimal amount of drug release at each pH range. Furthermore, anti-bacterial studies revealed that the synthesized BM-g-poly(AA) ~ Cur was effective against both gram-negative and gram-positive bacteria, with maximum values of zones of inhibition of 16 mm in diameter, thereby showing the best results in comparison to the already developed matrices to date. As a result, the newly discovered BM-g-poly(AA) ~ Cur properties reflect the hydrogel network's suitability for drug release and anti-bacterial applications.

Preparation of Crosslinked Poly(acrylic acid-co-acrylamide)-Grafted Deproteinized Natural Rubber/Silica Composites as Coating Materials for Controlled Release of Fertilizer

The crosslinked poly(acrylic acid-co-acrylamide)-grafted deproteinized natural rubber/silica ((PAA-co-PAM)-DPNR/silica) composites were prepared and applied as coating materials for fertilizer in this work. The crosslinked (PAA-co-PAM)-DPNR was prepared via emulsion graft copolymerization in the presence of MBA as a crosslinking agent. The modified DPNR was mixed with various contents of silica (10 to 30 phr) to form the composites. The existence of crosslinked (PAA-co-PAM) after modification provided a water adsorption ability to DPNR. The swelling degree values of composites were found in the range of 2217.3 ± 182.0 to 8132.3 ± 483.8%. The addition of silica in the composites resulted in an improvement in mechanical properties. The crosslinked (PAA-co-PAM)-DPNR with 20 phr of silica increased its compressive strength and compressive modulus by 1.61 and 1.55 times compared to the unloaded silica sample, respectively. There was no breakage of samples after 80% compression strain. Potassium nitrate, a model fertilizer, was loaded into chitosan beads with a loading percentage of 40.55 ± 1.03% and then coated with the modified natural rubber/silica composites. The crosslinked (PAA-co-PAM)-DPNR/silica composites as the outer layers had the ability of holding water in their structure and retarded the release of fertilizer. These composites could be promising materials for controlled release and water retention that would have potential for agricultural application.

Maleic acid as an important monomer in synthesis of stimuli-responsive poly(acrylic acid-co-acrylamide-co-maleic acid) superabsorbent polymer

Poly(acrylic acid-co-acrylamide-co-maleic acid) (p(AA-co-AM-co-MA)) superabsorbent polymer was synthesized from acrylic acid (AA), acrylamide (AM), and maleic acid (MA) via free radical copolymerization. Results showed the presence of maleic acid in structure of superabsorbent has the key and superior role in creating a smart superabsorbent. The structure, morphology, and strength of the superabsorbent were characterized using FT-IR, TGA, SEM, and rheology analysis. The effect of different factors was investigated to determine the ability of water absorbency of the superabsorbent. According to optimized conditions, the water absorbency capacity of the superabsorbent in distilled water (DW) was 1348 g/g and in a solution containing 1.0 wt.% NaCl (SCS) was 106 g/g. The water retention ability of the superabsorbent was also investigated. The kinetic swelling of superabsorbent was identified by Fickian diffusion and Schott's pseudo-second-order model. Furthermore, the reusability of superabsorbent was studied in distilled water and saline solution. The ability of superabsorbent was investigated in simulated urea and glucose solutions, and very good results were obtained. The response ability of the superabsorbent was confirmed by swelling and shrinking behavior against changes of temperature, pH, and ionic strength.

Design, synthesis, and application of thermally responsive draw solutes for sustainable forward osmosis desalination: A review

Forward osmosis (FO) is an emerging sustainable desalination technology; however, it is not a stand-alone process and requires an additional step to recover the water or regenerate the draw solute (DS), making it energy extensive. Therefore, incorporating inexpensive energy sources for DS regeneration is a viable solution to compete with reverse osmosis desalination technology. Hence, selecting suitable DS and its regeneration became a crucial research focus in FO desalination. Among various DSs reported, thermally responsive DSs (TRDS) provide an opportunity to integrate low-grade energy sources for DS regeneration. Utilizing such inexpensive energy will reduce fossil fuel energy demand, lower the cost of desalination, and minimize the carbon footprint. Hence, this review explores the TRDS for FO-based desalination with its design, synthesis, and applications. The manuscript has discussed the classification and selection criteria for the DSs, and how traditional and new-generation TRDSs are designed and synthesized from cationic and anionic moieties of ionic liquids, hydrogels, and other chemicals. The manuscript has also given importance to design criteria such as osmotic strength, viscosity, toxicity, and thermal stability for TRDSs. Furthermore, a detailed discussion on the FO performance, energy, and economic aspects of TRDSs has been reviewed, along with a discussion on the possible low-grade energy sources for the recovery of TRDS. Finally, the challenges and future directions for TRDSs have been discussed to drive FO toward sustainable desalination technology.

Temperature-responsive hydrogel prepared from carboxymethyl cellulose-stabilized N-vinylcaprolactam with potential for fertilizer delivery

The growth of plants is highly dependent on sufficient water and suitable fertilizer nutrients, but the soil often loses moisture and the fertilizers are low efficiency. To address this issue, the temperature-responsive hydrogels were developed using the N-vinylcaprolactam (NVCL) dispersed in water through the emulsification of carboxymethyl cellulose (CMC) and acrylamide (AM), and urea was loaded into the hydrogel as a fertilizer. The amount of CMC and monomer have an effect on the structure, mechanical properties, swelling ability, and temperature sensitivity of the hydrogel. Therefore, the maximum swelling ratio of the hydrogel can reach 2056 % with the increasing hydrophilic groups, and the hydrogel exhibits a deswelling behavior as the temperature rises to higher than LCST due to the temperature responsiveness. Moreover, the fertilizer can rapidly release when the temperature is higher than LSCT, and exhibits similar release behavior in water and soil. Thus, the temperature-responsive hydrogel shows a great potential application for the controlled release of water and fertilizer in agriculture and forestry.

Synthesis of starch-based smart hydrogel derived from rice-cooked wastewater for agricultural use

The synthesis of biodegradable hydrogel based on naturally available macromolecules is an important area of research. We synthesized new hydrogel using rice-cooked wastewater (starch), acrylamide, and 2-acrylamido-2-methylpropansulfonic acid in an aqueous medium. The synthesis approach is facile, low-cost, eco-friendly, and novel. The synthesized materials were characterized by scanning electron microscope, X-ray diffraction, Fourier-transform infrared spectroscopy, X-ray photoelectron spectroscopy, Raman spectroscopy, and Thermogravimetric analysis. The hydrogel exhibited maximum tap water absorbency (158.3 g/g) at pH 7, saline water absorbency (50 g/g), urea solution absorbency (141.2 g/g) at 24 h, and excellent water retention capability (47 wt% at 70 °C, 12 h, and 89 wt% at 30 °C, 24 h). Chili plants, mung beans, and pea seeds germinated and grew well in the hydrogel and hydrogel-mixed soil, respectively. The biodegradability study shows 34.6 % at 120 days in soil and 6.5 % at 30 days in the open air. These findings could entice agricultural development in dry soil.

Synthesis and Characterization of Orange Peel Modified Hydrogels as Efficient Adsorbents for Methylene Blue (MB)

In recent years, due to the developments in the textile industry, water contaminated with synthetic dyes such as methylene blue (MB) has become an environmental threat based on the possible impacts in terms of chemical and biochemical demand, which leads to disturbance in aquatic plants photosynthesis, besides their possible toxicity and carcinogenicity for humans. In this work, an adsorbent hydrogel is prepared via free radical polymerization comprising acrylic acid (PAA) as a monomer and orange peel (OP) as a natural modifier rich in OH and COOH present in its cellulose and pectin content. The resulting hydrogels were optimized in terms of the content of OP and the number of cross-linkers and characterized morphologically using Scanning electron microscopy. Furthermore, BET analysis was used to follow the variation in the porosity and in terms of the surface area of the modified hydrogel. The adsorption behavior was found to follow pseudo-second-order as a kinetic model, and Langmuir, Freundlich, and Temkin isotherm models. The combination of OP and PAA has sharply enhanced the adsorption percent of the hydrogel to reach 84% at the first 10 min of incubation with an adsorption capacity of more than 1.93 gm/gm. Due to its low value of pHPZc, the desorption of MB was efficiently performed at pH 2 using HCl, and the desorbed OP-PAA were found to be reusable up to ten times without a decrease in their efficiency. Accordingly, OP-PAA hydrogel represents a promising efficient, cost-effective, and environmentally friendly adsorbent for MB as a model cationic dye that can be applied for the treatment of contaminated waters.

Environmentally friendly hydrogel: A review of classification, preparation and application in agriculture

Superabsorbent hydrogel (SH) is three-dimensional (3D) cross-linked hydrophilic polymer that can absorb and retain large quantities of water or other aqueous solutions. SH is made of water-affinity monomers and is widely used in biomedicine, wastewater treatment, hygiene and slow-release fertilizers (SRFs). This article focused on the preparation methods of SH, superabsorbent hydrogel composite and the application of SH in agriculture. By selecting various synthetic technologies and cross-linking agents, a series of chemical cross-linking or physical networks can be designed and tailored to meet specific applications. In view of the excellent characteristics of water absorption, biodegradability, water retention and slow-release capacity, SH occupies a dominant position in the SRFs market. In this work, the agricultural application of SH in double coated SRFs and nutrients carriers is also discussed. Some mechanisms related to the nutrient release were analyzed by mathematical models. In addition, some agronomic benefits of using superabsorbent hydrogels in improving water absorption, water holding capacity and increasing crop yields were also discussed. Although SH has certain shortcomings, from the perspective of long-term development, it will further show great potential in sustainable agriculture.

One-pot synthesis of brewer's spent grain-supported superabsorbent polymer for highly efficient uranium adsorption from wastewater

High-efficient and fast adsorption of uranium is important to reduce the hazards caused by the uranium contamination of water environment due to the increased human activities. Herein, brewer's spent grain (BSG)-supported superabsorbent polymers (SAP) with different cross-linking densities are prepared as cheap and eco-friendly adsorbents for the first time via one-pot swelling and graft polymerization. A 7 wt% NaOH solution is used to swell BSG before grafting and subsequently neutralize the acrylic acid to control the reaction rate without producing alkaline wastewater. Compared with the traditional methods, swelling improves the grafting density and the utilization of raw materials due to the increased disorder degree of the BSG fibers. This results in the grafting of abundant carboxyl and amide groups onto the BSG backbone, forming a strongly hydrophilic polymer network of the BSG-SAP. Compared with the reference polymers without BSG, BSG-SAP presents higher adsorption capacity and enhanced reusability. The highly cross-linked BSG-SAP (BSG-SAP-H) shows an outstanding adsorption capacity of U(VI) (1465 mg/g at pH₀ = 4.6), a fast adsorption rate (81% of equilibrium adsorption capacity in 15 min), and a high selectivity in the presence of competing ions. Adsorption mechanism studies reveal the involvement of amide groups, a bidentate binding structure between UO₂²⁺ and the carboxyl groups, and a cation exchange between Na⁺ and UO₂²⁺. More importantly, the adsorption capacity of BSG-SAP-H reaches 254.4 mg/g in the fixed-bed column experiment at a low initial concentration (c₀(U) = 30 mg/L) and keeps 80% of the adsorption capacity after four cycles, indicating a great potential for uranium removal from wastewater. This work shows a suitable approach to explore the untreated biomass to prepare SAP with enhanced adsorption performance via a general and low-cost strategy.

Preparation and Properties of Salecan-Soy Protein Isolate Composite Hydrogel Induced by Thermal Treatment and Transglutaminase

Salecan (Sal) is a novel marine microbial polysaccharide. In the present research, Sal and soy protein isolate (SPI) were adopted to fabricate Sal–SPI composite hydrogel based on a stepwise process (thermal treatment and transglutaminase induction). The effect of Sal concentration on morphology, texture properties, and the microstructure of the hydrogel was evaluated. As Sal concentration varied from 0.4 to 0.6 wt%, hydrogel elasticity increased from 0.49 to 0.85 mm. Furthermore, the internal network structure of Sal–SPI composite hydrogel also became denser and more uniform as Sal concentration increased. Rheological studies showed that Sal–SPI elastic hydrogel formed under the gelation process. Additionally, FTIR and XRD results demonstrated that hydrogen bonds formed between Sal and SPI molecules, inferring the formation of the interpenetrating network structure. This research supplied a green and simple method to fabricate Sal–SPI double network hydrogels.

Rapid preparation of N-CNTs/P(AA-co-AM) composite hydrogel via frontal polymerization and its mechanical and conductive properties

Deep eutectic solvent (DES) was prepared by using acrylic acid (AA) and acrylamide (AM) as hydrogen bonding donors (HBD) and choline chloride (ChCl) as hydrogen bonding receptors (HBA). Nitrogen-doped carbon nanotubes (N-CNTs) were dispersed in DES as fillers, and N-CNTs/P(AA-co-AM) composite hydrogels were prepared by FP. The interaction mode between the hydrogel and N-CNTs was characterized by Fourier infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The mechanical properties, pH response and electrical conductivity of the composite hydrogels were studied. The results showed that the mechanical properties of the hydrogel were significantly enhanced with the increase of N-CNT content. The tensile strength and compressive strength of the FP4 composite hydrogel reached 5.42 MPa and 4.29 MPa, respectively. Due to the dissociation of carboxyl groups in AA in an alkaline environment the composite hydrogel showed excellent pH response performance. The conductivity of the hydrogel was also found to be improved with the content of N-CNTs. When the content of N-CNTs is 1.0 wt%, the conductivity of the hydrogel was 4.2 times higher than that of the hydrogel without N-CNTs, and connecting it to a circuit can make an LED lamp emit bright light. In this study, a simple and green method was proposed to prepare composite hydrogels with excellent mechanical properties and electrical conductivity by FP of DES in less than 5 min.

This study provides a rapid and low-energy method for the preparation of nanocomposite hydrogels with excellent mechanical properties and electrical conductivity.

Hydrogel Application in Urban Farming: Potentials and Limitations—A Review

Urban agriculture plays a vital role in ensuring the self-sufficiency of a great variety of fresh vegetables and nutrients. It promotes a sustainable food system as well as reducing the dependency on imports for the growing population. Urban farming has made it possible for agriculture practices to be implemented anywhere at any time in a sophisticated way. Hydrogel has been introduced in urban agriculture in the past few decades. However, the application of hydrogel in urban agriculture is still being explored in terms of hydrogel types, structure, physical and chemical properties, change due to external factors, and its suitability for different plant species. This review discusses the potentials and limitations of hydrogel in different application conditions. We present the state of knowledge on hydrogel production and crosslinking methods, hydrogel characteristics, water absorption and release mechanisms of hydrogel, hydrogel advantages and limitations, and current and future applications in urban farming.

Adsorption behavior and mechanism of Lead (Pb2+) by sulfate polysaccharide from Enteromorpha prolifera

Lead (Pb²⁺) pollution poses severe healthy and ecological risks to humans. In this work, sulfate polysaccharide from Enteromorpha prolifera (SPE) was utilized for Pb²⁺ adsorption from simulated intestinal fluid. In order to evaluate its adsorption behaviors comprehensively, batch adsorption of Pb²⁺ was investigated under different conditions. Results showed that SPE presents high adsorption ability for Pb²⁺ through chemical adsorption process and the maximum adsorption capacity for Pb²⁺ was 278.5 mg/g. And SPE exhibited higher removal efficiency (≥60%) for trace Pb²⁺ (<10 mg/L) compared to that of other adsorbents based on polysaccharide. Besides, its adsorption can be described by Langmuir isotherm and pseudo-second-order kinetic models. Further, XRD, FTIR, and XPS were used to characterize the possible interaction of Pb²⁺ with SPE, and the results showed that carboxyl and hydroxyl groups in SPE play more important role than that of sulfate group. Our work represents the first assessment of Pb²⁺ adsorption properties of SPE. This investigation highlights the potential application of SPE to protect the body from hazard of food-derived heavy metals.

Stiff and strong hydrogel tube with great mechanical properties and high stability in various solutions

Hydrogel tubes are widely used in fields such as artificial blood vessels, drug delivery, biomedical scaffolds and cell adhesion, yet their application is often limited by unsatisfactory mechanical properties and poor stability in various solutions. Herein, a novel hydrogel tube exhibiting a remarkable mechanical performance and stability in various solutions is prepared by introducing a dual physically cross-linked double network (DN) hydrogel matrix. The obtained hydrogel tube can withstand ∼60 N load without fracture and be stretched to over twice its original length before and after immersing in various solutions. The great mechanical properties and stability in various solutions of hydrogel tubes are due to the introduction of a dual physically cross-linked poly(acrylamide-co-acrylic acid)/carboxymethylcellulose sodium/Fe³⁺ DN hydrogel, which possesses high elastic modulus (3.71 MPa), fracture energy (15.4 kJ m^-2), and great stability in various solutions. In addition, the hydrogel tubes with different thickness, diameters, shapes and the multiple branched hydrogel tubes can also be fabricated to enable further functionalization for application requirements. Therefore, this new type of hydrogel tube presents tremendous potential for applications in biomedical and engineering fields.

Phosphate removal by a La(OH)3 loaded magnetic MAPTAC-based cationic hydrogel: Enhanced surface charge density and Donnan membrane effect

Cationic hydrogels have received great attention to control eutrophication and recycle phosphate. In this study, a type of La(OH)₃ loaded magnetic MAPTAC-based cationic hydrogel (La(OH)₃@MMCH) was developed as a potential adsorbent for enhanced phosphate removal from aqueous environment. La(OH)₃@MMCH exhibited high adsorption capacity of 105.72±5.99 mg P/g, and reached equilibrium within 2 hr. La(OH)₃@MMCH could perform effectively in a wide pH range from 3.0 to 9.0 and in the presence of coexisting ions (including SO₄^2-, Cl^-, NO₃^-, HCO₃^-, SiO₄^4- and HA). The adsorption-desorption experiment indicated that La(OH)₃@MMCH could be easily regenerated by using NaOH-NaCl as the desorption agent, and 73.3% adsorption capacity remained after five cycles. Moreover, La(OH)₃@MMCH was employed to treat surface water with phosphate concentration of 1.90  mg/L and showed great removal efficiency of 95.21%. Actually, MMCH showed high surface charge density of 34.38-59.38 meq/kg in the pH range from 3.0 to 11.0 and great swelling ratio of 3014.57% within 24 h, indicating that MMCH could produce the enhanced Donnan membrane effect to pre-permeate phosphate. Furthermore, the bifunctional structure of La(OH)₃@MMCH enabled it to capture phosphate through electrostatic attraction and ligand exchange. All the results prove that La(OH)₃@MMCH is a promising adsorbent for eutrophication control and phosphate recovery.

Functionalization and Antibacterial Applications of Cellulose-Based Composite Hydrogels

Pathogens, especially drug-resistant pathogens caused by the abuse of antibiotics, have become a major threat to human health and public health safety. The exploitation and application of new antibacterial agents is extremely urgent. As a natural biopolymer, cellulose has recently attracted much attention due to its excellent hydrophilicity, economy, biocompatibility, and biodegradability. In particular, the preparation of cellulose-based hydrogels with excellent structure and properties from cellulose and its derivatives has received increasing attention thanks to the existence of abundant hydrophilic functional groups (such as hydroxyl, carboxy, and aldehyde groups) within cellulose and its derivatives. The cellulose-based hydrogels have broad application prospects in antibacterial-related biomedical fields. The latest advances of preparation and antibacterial application of cellulose-based hydrogels has been reviewed, with a focus on the antibacterial applications of composite hydrogels formed from cellulose and metal nanoparticles; metal oxide nanoparticles; antibiotics; polymers; and plant extracts. In addition, the antibacterial mechanism and antibacterial characteristics of different cellulose-based antibacterial hydrogels were also summarized. Furthermore, the prospects and challenges of cellulose-based antibacterial hydrogels in biomedical applications were also discussed.

Smart pH-Sensitive Hydrogel Based on the Pineapple Peel-Oxidized Hydroxyethyl Cellulose and the Hericium erinaceus Residue Carboxymethyl Chitosan for Use in Drug Delivery

Pineapple and hericium erinaceus (HE) produce a lot of residues in the process of food processing. These processed residues are good potential derivative precursors. In this investigation, a simple and non-toxic method was developed to prepare one new composite hydrogel by the Schiff base reaction between the aldehyde group of oxidized hydroxyethyl cellulose (OHEC) from processed pineapple peel residue and the amino group of carboxymethyl chitosan (CMCS) from processed HE residue. Subsequently, a series of experiments toward these new hydrogel polymers including structure characterization and performances were applied. The resultant hydrogel polymers were characterized by Fourier transform infrared spectroscopy and scanning electron microscopy and confirmed with thermogravimetry. It was observed that the modification of cellulose and chitin was adequate, and the synthesis of OHEC/CMCS hydrogel polymers was successful. The gelation time experiments indicated that the shortest gel time was 33 s at a mass ratio of 4:6 (OHEC-70:CMCS). The hydrogel showed good swelling properties. The maximum swelling rate reached 11.58 g/g, and the swelling rate decreased with the increase of the oxidation degree of OHEC. The drug delivery applications of the prepared hydrogel were evaluated with bovine serum albumin (BSA) as a model drug releasing in vitro. It was discovered that the BSA release from the hydrogel was pH sensitive under simulated gastrointestinal conditions. All of these attributes indicate that the novel prepared hydrogel polymers have the potential as good carriers for oral delivery of protein-type drugs.

Enhanced Interface Properties and Stability of Lignocellulose Nanocrystals Stabilized Pickering Emulsions: The Leading Role of Tannic Acid

Cellulose and tannin are both abundant and biodegradable biopolymers, whose integrations show great potential in the food field due to their nutritional properties and biological activity. Here, lignocellulose nanocrystals (LCNC) isolated from pineapple peel were complexed with tannic acid (TA) through hydrogen-bonding interaction to prepare the LCNC/TA complex for stabilizing Pickering emulsions. Introducing TA decreased the interfacial tension (23.8-20.1 mN/m) and water contact angle (83.2-56.2°) with the LCNC/TA ratio ranging from 1:0 to 1:0.8 (w/w) but increased the size of the LCNC/TA complex. The droplet size of emulsions decreased from 115.0 to 51.3 μm accompanied by improved rheological properties. The emulsions stabilized by the LCNC/TA complex exhibited higher storage and environmental stabilities than those stabilized by LCNC alone. Interestingly, TA effectively promoted the interfacial adsorption of LCNC to build a stronger interfacial layer. The emulsion network structure was enhanced due to the formation of hydrogen-bonding interaction between LCNC and TA in the continuous phase.

Waste Materials as a Resource for Production of CMC Superabsorbent Hydrogel for Sustainable Agriculture

Waste materials are receiving more attention as concerns about the future of our planet increase. Cellulose is the most common substance in agricultural waste. Agricultural wastes containing cellulose are misplaced resources that could be reused in various fields for both environmental and economic benefits. In this work, 32 different kinds of waste are investigated for chemical modification in order to obtain carboxymethyl cellulose for the production of a superabsorbent hydrogel that can be applied in agriculture. A brief literature review is provided to help researchers wishing to obtain carboxymethyl cellulose by carboxymethylation starting with waste materials. We also provide details about methods to obtain as well as verify carboxymethylation. Carboxymethyl cellulose (CMC), as a constituent of cellulosic water and superabsorbent hydrogels with applications in agriculture, is described. Superabsorbent hydrogels with CMC are able to absorb huge amounts of water and are biodegradable.

Cellulosic Polymers for Enhancing Drug Bioavailability in Ocular Drug Delivery Systems

One of the major impediments to drug development is low aqueous solubility and thus poor bioavailability, which leads to insufficient clinical utility. Around 70–80% of drugs in the discovery pipeline are suffering from poor aqueous solubility and poor bioavailability, which is a major challenge when one has to develop an ocular drug delivery system. The outer lipid layer, pre-corneal, dynamic, and static ocular barriers limit drug availability to the targeted ocular tissues. Biopharmaceutical Classification System (BCS) class II drugs with adequate permeability and limited or no aqueous solubility have been extensively studied for various polymer-based solubility enhancement approaches. The hydrophilic nature of cellulosic polymers and their tunable properties make them the polymers of choice in various solubility-enhancement techniques. This review focuses on various cellulose derivatives, specifically, their role, current status and novel modified cellulosic polymers for enhancing the bioavailability of BCS class II drugs in ocular drug delivery systems.

Development of Arabic gum-based AgTiO2 nanocomposite hydrogel as high efficient adsorbent of cationic dye methylene blue from water

The chemically crosslinked silver titanium dioxide embedded Arabic gum grafted polyacrylamide-polyacrylonitrile nanocomposite AgTiO₂@AG-g-P(AM-co-AN)was successfully synthesized and investigated by ATR-IR, XRD, and SEM. The synthesis optimization parameters of AG-g-P(AM-co-AN)were 5% AG, 1/0.5 AM/AN monomer molar ratio, 0.5 mg MBA cross-linker, and AgTiO₂ content (1%) gives AgTiO₂@AG-g-P(AM-co-AN) nanocomposite. While adsorption studies for AgTiO₂@AG-g-P(AM-co-AN) exhabited the maximum adsorption capacity (104.50 ± 3.02 mg/g) at concentration (150 mg/L), MB concentration (15 mg/L) and pH (8.0). The adsorption nonlinear kinetics models were used. Pseudo-second order governs the adsorption process, and the Langmuir model is more suited than Freundlich and Temkin.

Hotspots, Frontiers, and Emerging Trends of Superabsorbent Polymer Research: A Comprehensive Review

Superabsorbent polymer (SAP) is a kind of functional macromolecule with super-high water absorption and retention properties, which attracts extensive research and has wide application, especially in the areas of hygiene and agriculture. With reference to the Web of Science database, the SAP research literature from 2000 to 2019 is reviewed both quantitatively and qualitatively. By examining research hotspots, top research clusters, the most influential works, the representative frontier literature, and key emerging research trends, a visual panorama of the continuously and significantly increasing SAP research over the past 2 decades was presented, and issues behind the sharp increase in the literature were discovered. The findings are as follows. The top ten keywords/hotspots headed by hydrogel highlight the academic attention on SAP properties and composites. The top ten research themes headed by clay-based composites which boast the longest duration and the strongest impact have revealed the academic preference for application rather than theoretical study. Academically influential scholars and research studies have been acknowledged, and the Wu group was at the forefront of the research; however, more statistically significant works have been less detected in the last 10 years despite the sharper increase in publications. Hydrogel, internal curing, and aerogel are both current advances and future directions.

Designing cellulose hydrogels from non-woody biomass

Hydrogels are an attractive system for a myriad of applications. While most hydrogels are usually formed from synthetic materials, lignocellulosic biomass appears as a sustainable alternative for hydrogel development. The valorization of biomass, especially the non-woody biomass to meet the growing demand of the substitution of synthetics and to leverage its benefits for cellulose hydrogel fabrication is attractive. This review aims to present an overview of advances in hydrogel development from non-woody biomass, especially using native cellulose. The review will cover the overall process from cellulose depolymerization, dissolution to crosslinking reaction and the related mechanisms where known. Hydrogel design is heavily affected by the cellulose solubility, crosslinking method and the related processing conditions apart from biomass type and cellulose purity. Hence, the important parameters for rational designs of hydrogels with desired properties, particularly porosity, transparency and swelling characteristics will be discussed. Current challenges and future perspectives will also be highlighted.

Preparation and Characterization of Cellulose Composite Hydrogels From Tea Residue and Single-Walled Carbon Nanotube Oxides and Its Potential Applications

Hydrogels were prepared from tea cellulose with the addition of single-walled carbon nanotube oxides in 1-allyl-3-methylimidazolium chloride. Single-walled carbon nanotube oxides/tea cellulose hydrogels (TCH-SWNTs) were characterized by Fourier transform infrared, x-ray diffraction, texture profile analysis, and thermogravimetric analysis. The adsorption capacity of methylene blue using the prepared hydrogels was also investigated. The hydrogels exhibited greater thermal stability and intensive textural property with the addition of single-walled carbon nanotube oxides. Compared with undoped TCHs, the weight loss peak moved from 280 to 323°C, and the values of hardness, fracturability, gumminess, and resilience were 8.4, 5.3, 10.8, and 1.9, respectively, times higher than that of TCHs. As an absorbent of methylene blue, TCH-SWNTs accorded to a pseudo-second-order kinetic model, good adsorption capacity (13.8 mg/g), and good adsorption ratio (27.59%) and showed potential as a drug carrier.

Proteins from Agri-Food Industrial Biowastes or Co-Products and Their Applications as Green Materials

A great amount of biowastes, comprising byproducts and biomass wastes, is originated yearly from the agri-food industry. These biowastes are commonly rich in proteins and polysaccharides and are mainly discarded or used for animal feeding. As regulations aim to shift from a fossil-based to a bio-based circular economy model, biowastes are also being employed for producing bio-based materials. This may involve their use in high-value applications and therefore a remarkable revalorization of those resources. The present review summarizes the main sources of protein from biowastes and co-products of the agri-food industry (i.e., wheat gluten, potato, zein, soy, rapeseed, sunflower, protein, casein, whey, blood, gelatin, collagen, keratin, and algae protein concentrates), assessing the bioplastic application (i.e., food packaging and coating, controlled release of active agents, absorbent and superabsorbent materials, agriculture, and scaffolds) for which they have been more extensively produced. The most common wet and dry processes to produce protein-based materials are also described (i.e., compression molding, injection molding, extrusion, 3D-printing, casting, and electrospinning), as well as the main characterization techniques (i.e., mechanical and rheological properties, tensile strength tests, rheological tests, thermal characterization, and optical properties). In this sense, the strategy of producing materials from biowastes to be used in agricultural applications, which converge with the zero-waste approach, seems to be remarkably attractive from a sustainability prospect (including environmental, economic, and social angles). This approach allows envisioning a reduction of some of the impacts along the product life cycle, contributing to tackling the transition toward a circular economy.

Recent Developments of Carboxymethyl Cellulose

Carboxymethyl cellulose (CMC) is one of the most promising cellulose derivatives. Due to its characteristic surface properties, mechanical strength, tunable hydrophilicity, viscous properties, availability and abundance of raw materials, low-cost synthesis process, and likewise many contrasting aspects, it is now widely used in various advanced application fields, for example, food, paper, textile, and pharmaceutical industries, biomedical engineering, wastewater treatment, energy production, and storage energy production, and storage and so on. Many research articles have been reported on CMC, depending on their sources and application fields. Thus, a comprehensive and well-organized review is in great demand that can provide an up-to-date and in-depth review on CMC. Herein, this review aims to provide compact information of the synthesis to the advanced applications of this material in various fields. Finally, this article covers the insights of future CMC research that could guide researchers working in this prominent field.

Lignin-derived (nano)materials for environmental pollution remediation: Current challenges and future perspectives

The supply of affordable drinking and sufficiently clean water for human consumption is one of the world's foremost environmental problems and a large number of scientific research works are addressing this issue Various hazardous/toxic environmental contaminants in water bodies, both inorganic and organic (specifically heavy metals and dyes), have become a serious global problem. Nowadays, extensive efforts have been made to search for novel, cost effective and practical biosorbents derived from biomass resources with special attention to value added, biomass-based renewable materials. Lignin and (nano)material adorned lignin derived entities can proficiently and cost effectively remove organic/inorganic contaminants from aqueous media. As low cost of preparation is crucial for their wide applications in water/wastewater treatment (particularly industrial water), future investigations must be devoted to refining and processing the economic viability of low cost, green lignin-derived (nano)materials. Production of functionalized lignin, lignin supported metal/metal oxide nanocomposites or hydrogels is one of the effective approaches in (nano)technology. This review outlines recent research progresses, trends/challenges and future prospects about lignin-derived (nano)materials and their sustainable applications in wastewater treatment/purification, specifically focusing on adsorption and/or catalytic reduction/(photo)degradation of a variety of pollutants.

Synthesis of a super-absorbent nanocomposite hydrogel based on vinyl hybrid silica nanospheres and its properties

Superabsorbent polymers as soft materials that can absorb water have aroused great interest in the fields of agriculture and forestry. Water absorption and water retention performance of a hydrogel are important indicators to evaluate its practical application. However, few reports show that hydrogels have both excellent water absorption and water retention properties. To date, superabsorbent hydrogels with a swelling capacity of more than 3000 g g⁻¹ have rarely been reported. In this work, a novel superabsorbent poly(acrylic acid) (PAA)-based nanocomposite hydrogel (NC gel) was prepared via free radical polymerization of acrylic acid by using vinyl hybrid silica nanospheres (VSNPs) as the cross-linking agent. The PAA NC hydrogel achieved a great swelling ratio of more than 5000 times in deionized water at 323 K, and the swollen hydrogel could hold 60% moisture when it was exposed to the air at 303 K for 42 h. Moreover, the hydrogel also obtained a good swelling ratio of 136 g g⁻¹ in NaCl solution. The PAA NC hydrogel showed excellent repetitive swelling ability. The influences of variable factors (acrylic acid, initiator and sodium hydroxide) on the swelling ratio of the NC hydrogel were researched. It can be speculated that the PAA NC hydrogel has potential application in agriculture and forestry areas due to its excellent water absorption and water retention properties.

Superabsorbent polymers as soft materials that can absorb water have aroused great interest in the fields of agriculture and forestry.