In Situ Analysis Reveals the Role of 2D Perovskite in Preventing Thermal-Induced Degradation in 2D/3D Perovskite Interfaces

Surface Planarization-Epitaxial Growth Enables Uniform 2D/3D Heterojunctions for Efficient and Stable Perovskite Solar Modules

Two-dimensional/three-dimensional (2D/3D) halide perovskite heterojunctions are widely used to improve the efficiency and stability of perovskite solar cells. However, interfacial defects between the 2D and 3D perovskites and the poor coverage of the 2D capping layer still hinder long-term stability and homogeneous charge extraction. Herein, a surface planarization strategy on 3D perovskite is developed that enables an epitaxial growth of uniform 2D/3D perovskite heterojunction via a vapor-assisted process. The homogeneous charge extraction and suppression of interfacial nonradiative recombination is achieved by forming a uniform 2D/3D interface. As a result, a stabilized power output efficiency of 25.97% is achieved by using a 3D perovskite composition with a bandgap of 1.55 eV. To demonstrate the universality of the strategy applied for different perovskites, the champion device based on a 1.57 eV bandgap 3D perovskite results in an efficiency of 25.31% with a record fill factor of 87.6%. Additionally, perovskite solar modules achieve a designated area (24.04 cm2) certified efficiency of 20.75% with a high fill factor of 80.0%. Importantly, the encapsulated uniform 2D/3D modules retain 96.9% of the initial efficiency after 1246 h operational tracking under 65 °C (ISOS-L-3 protocol) and 91.1% after 862 h under the ISOS-O-1 protocol.

Cation reactivity inhibits perovskite degradation in efficient and stable solar modules

Perovskite solar modules (PSMs) show outstanding power conversion efficiencies (PCEs), but long-term operational stability remains problematic. We show that incorporating N,N-dimethylmethyleneiminium chloride into the perovskite precursor solution formed dimethylammonium cation and that previously unobserved methyl tetrahydrotriazinium ([MTTZ]+) cation effectively improved perovskite film. The in situ formation of [MTTZ]+ cation increased the formation energy of iodine vacancies and enhanced the migration energy barrier of iodide and cesium ions, which suppressed nonradiative recombination, thermal decomposition, and phase segregation processes. The optimized PSMs achieved a record (certified) PCE of 23.2% with an aperture area of 27.2 cm2, with a stabilized PCE of 23.0%. The encapsulated PSM retained 87.0% of its initial PCE after ~1900 hours of maximum power point tracking at 85°C and 85% relative humidity under 1.0-sun illumination.

2D Phase Formation on 3D Perovskite: Insights from Molecular Stiffness

Several studies have demonstrated that low-dimensional structures (e.g., two-dimensional (2D)) associated with three-dimensional (3D) perovskite films enhance the efficiency and stability of perovskite solar cells. Here, we aim to track the formation sites of the 2D phase on top of the 3D perovskite and to establish correlations between molecular stiffness and steric hindrance of the organic cations and their influence on the formation and crystallization of 2D/3D. Using cathodoluminescence combined with a scanning electron microscopy technique, we verified that the formation of the 2D phase occurs preferentially on the grain boundaries of the 3D perovskite. This helps explain some passivation mechanisms conferred by the 2D phase on 3D perovskite films. Furthermore, by employing in situ grazing-incidence wide-angle X-ray scattering, we monitored the formation and crystallization of the 2D/3D perovskite using three cations with varying molecular stiffness. In this series of molecules, the formation and crystallization of the 2D phase are found to be dependent on both steric hindrance around the ammonium group and molecular stiffness. Finally, we employed a 2D/3D perovskite heterointerface in a solar cell. The presence of the 2D phase, particularly those formed from flexible cations, resulted in a maximum power conversion efficiency of 21.5%. This study provides insight into critical aspects related to how bulky organic cations' stiffness and steric hindrance influence the formation, crystallization, and distribution of 2D perovskite phases.

Temperature-Dependent Structural and Optoelectronic Properties of the Layered Perovskite 2-Thiophenemethylammonium Lead Iodide

Improved knowledge of the influence of temperature upon layered perovskites is essential to enable perovskite-based devices to operate over a broad temperature range and to elucidate the impact of structural changes upon the optoelectronic properties. We examined the Ruddlesden-Popper layered perovskite 2-thiophenemethylammonium lead iodide (ThMA2PbI4) and observed a structural phase transition between a high- and a low-temperature phase at 220 K using temperature-dependent X-ray diffraction, UV-visible absorption, and photoluminescence (PL) spectroscopy. The structural phase transition altered the tilt pattern of the inorganic octahedra layer, modifying the absorption and PL spectra. Further, we found a narrow and intense additional PL peak in the low-temperature phase, which we assigned to radiative emission from a defect-bound exciton state. In both phases we determined the thermal expansion coefficient and found values similar to those of cubic 3D perovskites, i.e., larger than those of typical substrates such as glass. These results demonstrate that the organic spacer plays a critical role in controlling the temperature-dependent structural and optoelectronic properties of layered perovskites and suggests more widely that strain management strategies may be needed to fully utilize layered perovskites in device applications.

Operationally stable perovskite solar modules enabled by vapor-phase fluoride treatment

The ever-increasing power conversion efficiency of perovskite solar cells has illuminated the future of the photovoltaic industry, but the development of commercial devices is hampered by their poor stability. In this study, we report a scalable stabilization method using vapor-phase fluoride treatment, which achieves 18.1%-efficient solar modules (228 square centimeters) with accelerated aging-projected T80 lifetimes (time to 80% of efficiency remaining) of 43,000 ± 9000 hours under 1-sun illumination at 30°C. The high stability results from vapor-enabled homogeneous fluorine passivation over large-area perovskite surfaces, suppressing defect formation energy and ion diffusion. The extracted degradation activation energy of 0.61 electron volts for solar modules is comparable to that of most reported stable cells, which indicates that modules are not inherently less stable than cells and closes the cell-to-module stability gap.

Advances and challenges in molecular engineering of 2D/3D perovskite heterostructures

Organic-inorganic hybrid perovskites have been intensively studied in past decades due to their outstanding performance in solar cells and other optoelectronic devices. Recently, the emergence of two-dimensional/three-dimensional (2D/3D) heterojunctions have enabled many solar cell devices with >25% power conversion efficiency, driven by advances in our understanding of the structural and photophysical properties of the heterojunctions and our ability to control these properties through organic cation configuration in 2D perovskites. In this feature article, we discuss a fundamental understanding of structural characteristics and the carrier dynamics in the 2D/3D heterojunctions and their impact factors. We further elaborate the design strategies for the molecular configuration of organic cations to achieve thorough management of these properties. Finally, recent advances in 2D/3D heterostructures in solar cells, light-emitting devices and photodetectors are highlighted, which translate fundamental understandings to device applications and also reveal the remaining challenges in ligand design for the next generation of stable devices. Future development prospects and related challenges are also provided, with wide perspectives and insightful thoughts.

Understanding and Mitigating Atomic Oxygen-Induced Degradation of Perovskite Solar Cells for Near-Earth Space Applications

Combining high efficiency with good radiation tolerance, perovskite solar cells (PSCs) are promising candidates to upend expanding space photovoltaic (PV) technologies. Successful employment in a Near-Earth space environment, however, requires high resistance against atomic oxygen (AtOx). This work unravels AtOx-induced degradation mechanisms of PSCs with and without phenethylammonium iodide (PEAI) based 2D-passivation and investigates the applicability of ultrathin silicon oxide (SiO) encapsulation as AtOx barrier. AtOx exposure for 2 h degraded the average power conversion efficiency (PCE) of devices without barrier encapsulation by 40% and 43% (w/o and with 2D-PEAI-passivation) of their initial PCE. In contrast, devices with a SiO-barrier retained over 97% of initial PCE. To understand why 2D-PEAI passivated devices degrade faster than less efficient non-passivated devices, various opto-electrical and structural characterications are conducted. Together, these allowed to decouple different damage mechanisms. Notably, pseudo-J-V curves reveal unchanged high implied fill factors (pFF) of 86.4% and 86.2% in non-passivated and passivated devices, suggesting that degradation of the perovskite absorber itself is not dominating. Instead, inefficient charge extraction and mobile ions, due to a swiftly degrading PEAI interlayer are the primary causes of AtOx-induced device performance degradation in passivated devices, whereas a large ionic FF loss limits non-passivated devices.

Improved 3D-2D Perovskite for Efficient Perovskite Photovoltaics with Low-Temperature Carbon Electrodes

Surface passivation and interface modification are effective strategies to acquire outstanding performances for perovskite solar cells (PeSCs). To suppress charge recombination and enhance the stability of the perovskite device, a hydrophobic two-dimensional (2D) perovskite is presented to construct a 3D-2D composite perovskite, passivating the perovskite surface/interfacial imperfection. Herein, a 3D-2D heterojunction perovskite is in situ synthesized on a 3D surface to maximize the charge transport and environmental stability. Through optimizing the annealing procedure systematically, the champion 3D-2D carbon-based PeSC achieves a power conversion efficiency of 17.95% and has wonderful long-term stability. Especially, an improved 3D-2D (3D-2D+) PeSC from restrict annealing even maintains 96.2% of the initial efficiency in air over 800 h and 90% efficiency under continuous 70 °C heating for 10 h owing to the passivation of the surface and thorough crystal boundary for the 3D-2D+ perovskite. The strong environmental stability of 3D-2D PeSCs has provided a wider avenue for fully low-temperature carbon-based PeSCs.

Fluorinated Cation-Based 2D Perovskites for Efficient and Stable 3D/2D Heterojunction Perovskite Solar Cells

Three-dimensional (3D) perovskite solar cells (PSCs) containing additives capable of forming two-dimensional (2D) structures in neat films have attracted attention due to their ability to enhance power conversion efficiency (PCE) in combination with improved operational stability. Herein, a newly designed fluorinated ammonium salt, 2-(perfluorophenyl)ethanaminium bromide:chloride50:50 (FEABr:Cl50:50), is introduced into CsMAFAPbI3-based PSCs with a standard n-i-p architecture. FEABr:Cl50:50 was used as an additive in the tin(IV) oxide (SnO2) electron transporting layer (ETL) as well as a surface treatment for the perovskite film. Used in this dual way, the additive was found to passivate charge-trapping defects within the SnO2 ETL and regulate the crystal growth of the perovskite layer. When FEABr:Cl50:50 was deposited onto the surface of the 3D perovskite film, it formed a thin hydrophobic 2D capping layer. Adopting this dual strategy led to the perovskite film having larger grain sizes, improved quality, and overall better device performance. As a result, the best-performing device exhibited a PCE of over 23% with negligible hysteresis in an n-i-p device architecture with an area of 0.2 cm2. Furthermore, unencapsulated devices with the hydrophobic 2D capping layer showed improved stability compared to the control device when measured under continuous light irradiation at a maximum power point (MPP) at 80 ± 5 °C in a humid (≈50%) environment.

Improved Efficiency and Stability in 1,5-Diaminonaphthalene Iodide-Passivated 2D/3D Perovskite Solar Cells

Engineering multidimensional two-dimensional/three-dimensional (2D/3D) perovskite interfaces as light harvesters has recently emerged as a potential strategy to obtain a higher photovoltaic performance in perovskite solar cells (PSCs) with enhanced environmental stability. In this study, we utilized the 1,5-diammonium naphthalene iodide (NDAI) bulky organic spacer for interface modification in 3D perovskites for passivating the anionic iodide/uncoordinated Pb2+ vacancies as well as facilitating charge carrier transfer by improving the energy band alignment at the perovskite/HTL interface. Consequently, the NDAI-treated 2D/3D PSCs showed an enhanced open-circuit voltage and fill factor with a remarkable power conversion efficiency (PCE) of 21.48%. In addition, 2D/3D perovskite devices without encapsulation exhibit a 77% retention of their initial output after 1000 h of aging under 50 ± 5% relative humidity. Furthermore, even after 200 h of storage in 85 °C thermal stress, the devices maintain 60% of their initial PCE. The defect passivation and interface modification mechanism were studied in detail by UV vis absorption, photoluminescence spectroscopy, atomic force microscopy (AFM), scanning electron microscopy (SEM), Fourier transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS), ultraviolet photoelectron spectroscopy (UPS), solid-state NMR, space-charge-limited current (SCLC) mobility measurement, and impedance spectroscopy. This study provides a promising path for perovskite surface modification in slowing their degradation against external stimuli, providing a future direction for increasing the perovskite device efficiency and durability.

Lead-sulfur interaction induced damp and water stability in pure formamidinium lead triiodide

Research efforts in various multitudes have been demonstrated to stabilize methylammonium (MA)- and bromide (Br)-free formamidinium lead triiodide (FAPI) perovskite thin films. Despite these commendable efforts, pure FAPI perovskite thin film is prone to critical phase-transition issues due to its thermodynamically stable non-perovskite phase (2H). Here, in this work, we propose a rational additivization strategy to overcome this challenge. Our multifunctional ammonium salt containing a sulfur heteroatom shifts the thermodynamic stability from the 2H phase to an intermediate phase closer to the cubic phase. Along with the high crystallinity, micron-sized grains with preferred (00h) facet orientation stem the Pb…S interaction to offer exceptional stability against high relative humidity, direct water incursion, and shelf-life aging. Our findings through experimental and theoretical studies substantiate the role of Pb…S interaction in stabilizing the perovskite cubic phase and the stoichiometric distribution of elemental components.

Synergy of 3D and 2D Perovskites for Durable, Efficient Solar Cells and Beyond

Three-dimensional (3D) organic-inorganic lead halide perovskites have emerged in the past few years as a promising material for low-cost, high-efficiency optoelectronic devices. Spurred by this recent interest, several subclasses of halide perovskites such as two-dimensional (2D) halide perovskites have begun to play a significant role in advancing the fundamental understanding of the structural, chemical, and physical properties of halide perovskites, which are technologically relevant. While the chemistry of these 2D materials is similar to that of the 3D halide perovskites, their layered structure with a hybrid organic-inorganic interface induces new emergent properties that can significantly or sometimes subtly be important. Synergistic properties can be realized in systems that combine different materials exhibiting different dimensionalities by exploiting their intrinsic compatibility. In many cases, the weaknesses of each material can be alleviated in heteroarchitectures. For example, 3D-2D halide perovskites can demonstrate novel behavior that neither material would be capable of separately. This review describes how the structural differences between 3D halide perovskites and 2D halide perovskites give rise to their disparate materials properties, discusses strategies for realizing mixed-dimensional systems of various architectures through solution-processing techniques, and presents a comprehensive outlook for the use of 3D-2D systems in solar cells. Finally, we investigate applications of 3D-2D systems beyond photovoltaics and offer our perspective on mixed-dimensional perovskite systems as semiconductor materials with unrivaled tunability, efficiency, and technologically relevant durability.

Inhibiting Interfacial Diffusion in Heterojunction Perovskite Solar Cells by Replacing Low-Dimensional Perovskite with Uniformly Anchored Quaternized Polystyrene

Surface heterojunction has been regarded as an effective method to improve the device efficiency of perovskite solar cells. Nevertheless, the durability of different heterojunction under thermal stress is rarely investigated and compared. In this work, benzylammonium chloride and benzyltrimethylammonium chloride are utilized to construct 3D/2D and 3D/1D heterojunctions, respectively. A quaternized polystyrene is synthesized to construct a three-dimensional perovskite/amorphous ionic polymer (3D/AIP) heterojunction. Due to the migration and volatility of organic cations, severe interfacial diffusion is found among 3D/2D and 3D/1D heterojunctions, in which the quaternary ammonium cations in the 1D structure are less volatile and mobile than the primary ammonium cations in the 2D structure. 3D/AIP heterojunction remains intact under thermal stress due to the strong ionic bond anchoring at the interface and the ultra-high molecular weight of AIP. Furthermore, the dipole layer formed by AIP can further reduce the voltage loss caused by nonradiative recombination at the interface by 0.088 V. Therefore, the devices based on the 3D/AIP heterojunction achieve a champion power conversion efficiency of 24.27% and maintain 90% of its initial efficiency after either thermal aging for 400 h or wet aging for 3000 h, showing a great promise for polymer/perovskite heterojunction towards real applications.

Engineering ligand reactivity enables high-temperature operation of stable perovskite solar cells

Perovskite solar cells (PSCs) consisting of interfacial two- and three-dimensional heterostructures that incorporate ammonium ligand intercalation have enabled rapid progress toward the goal of uniting performance with stability. However, as the field continues to seek ever-higher durability, additional tools that avoid progressive ligand intercalation are needed to minimize degradation at high temperatures. We used ammonium ligands that are nonreactive with the bulk of perovskites and investigated a library that varies ligand molecular structure systematically. We found that fluorinated aniliniums offer interfacial passivation and simultaneously minimize reactivity with perovskites. Using this approach, we report a certified quasi-steady-state power-conversion efficiency of 24.09% for inverted-structure PSCs. In an encapsulated device operating at 85°C and 50% relative humidity, we document a 1560-hour T₈₅ at maximum power point under 1-sun illumination.

Surface Passivation by Sulfur-Based 2D (TEA)2PbI4 for Stable and Efficient Perovskite Solar Cells

Perovskite solar cells (PSCs) with superior performance have been recognized as a potential candidate in photovoltaic technologies. However, defects in the active perovskite layer induce nonradiative recombination which restricts the performance and stability of PSCs. The construction of a thiophene-based 2D structure is one of the significant approaches for surface passivation of hybrid PSCs that may combine the benefits of the stability of 2D perovskite with the high performance of three-dimensional (3D) perovskite. Here, a sulfur-rich spacer cation 2-thiopheneethylamine iodide (TEAI) is synthesized as a passivation agent for the construction of a three-dimensional/two-dimensional (3D/2D) perovskite bilayer structure. TEAI-treated PSCs possess a much higher efficiency (20.06%) compared to the 3D perovskite (MA_0.9FA_0.1PbI₃) devices (17.42%). Time-resolved photoluminescence and femtosecond transient absorption spectroscopy are employed to investigate the effect of surface passivation on the charge carrier dynamics of the 3D perovskite. Additionally, the stability test of TEAI-treated perovskite devices reveals significant improvement in humid (RH ∼ 46%) and thermal stability as the sulfur-based 2D (TEA)₂PbI₄ material self-assembles on the 3D surface, making the perovskite surface hydrophobic. Our findings provide a reliable approach to improve device stability and performance successively, paving the way for industrialization of PSCs.

In Situ and Operando Characterizations of Metal Halide Perovskite and Solar Cells: Insights from Lab-Sized Devices to Upscaling Processes

The performance and stability of metal halide perovskite solar cells strongly depend on precursor materials and deposition methods adopted during the perovskite layer preparation. There are often a number of different formation pathways available when preparing perovskite films. Since the precise pathway and intermediary mechanisms affect the resulting properties of the cells, in situ studies have been conducted to unravel the mechanisms involved in the formation and evolution of perovskite phases. These studies contributed to the development of procedures to improve the structural, morphological, and optoelectronic properties of the films and to move beyond spin-coating, with the use of scalable techniques. To explore the performance and degradation of devices, operando studies have been conducted on solar cells subjected to normal operating conditions, or stressed with humidity, high temperatures, and light radiation. This review presents an update of studies conducted in situ using a wide range of structural, imaging, and spectroscopic techniques, involving the formation/degradation of halide perovskites. Operando studies are also addressed, emphasizing the latest degradation results for perovskite solar cells. These works demonstrate the importance of in situ and operando studies to achieve the level of stability required for scale-up and consequent commercial deployment of these cells.

1-Adamantanamine Hydrochloride Resists Environmental Corrosion to Obtain Highly Efficient and Stable Perovskite Solar Cells

Passivating the defective surface of perovskite film is a promising strategy to improve the stability and efficiency of perovskite solar cells (PSCs). Herein, 1-adamantanamine hydrochloride (ATH) is introduced to the upper surface of the perovskite film to heal the defects of the perovskite surface. The best-performance ATH-modified device has a higher efficiency (23.45%) than the champion control device (21.53%). The defects are passivated, interfacial nonradiative recombination is suppressed, and interface stress is released by the ATH deposited on the perovskite film, leading to longer carrier lifetimes and enhancement in open-circuit voltage (V_OC) and fill factor (FF) of the PSCs. With obvious improvement, V_OC and FF of 1.159 V and 0.796 for the control device are raised to 1.178 V and 0.826 for the ATH-modified device, respectively. Finally, during an operational stability measurement of more than 1000 h, the ATH-treated PSC exhibited better moisture resistance, thermal persistence, and light stability.

Precise modulation strategies of 2D/3D perovskite heterojunctions in efficient and stable solar cells

2D/3D perovskite heterojunctions exhibit promising prospects in the improvement of efficiency and stability of perovskite solar cells (PSCs). However, many challenges remain in the development of high-quality 2D/3D heterojunctions, such as a reliable pathway to control the perovskite phase and generally poor performance in inverted (p-i-n) devices, which limit their commercialization. Fortunately, many excellent works have proposed lots of strategies to solve these challenges, which have triggered a new wave of research on 2D/3D perovskite heterojunctions in recent years. In this paper, the latest research progress and the critical factors involved in the modulating mechanisms of PSCs with 2D/3D heterojunctions have been summarized and laid out systematically. The advantages of constructing 2D/3D perovskite heterojunctions in PSCs are highlighted, and the problems and related solutions of low-dimensional perovskites as passivation layers towards high-performance PSCs are also discussed in depth. Finally, the prospects of 2D/3D perovskite heterojunctions utilized in the passivation strategies to further improve the photovoltaic performance of PSCs in the future have been presented.

Influence of Two- and Three-Dimensional Engineering on the Trap State Distribution and Photophysical Properties of Lead Halide Perovskite Polycrystals

Constructing a two- and three-dimensional (2D/3D) heterojunction structure on the surface of a 3D perovskite film, termed 2D/3D engineering, is effective in elevating the stability of perovskite polycrystal-based photovoltaic and photoelectronic devices; however, it remains controversial whether this protocol is favorable or detrimental to the device performance. Here, we prepare a series of 2D/3D perovskite films by post-treating the perovskite polycrystalline film with different concentrations of phenethylammonium iodide (PEAI). Systematic spectroscopy and electrochemical studies illustrate that PEAI can penetrate the 3D perovskite network and eliminate the intrinsic trap states of perovskite polycrystals, while the 2D perovskite nanosheets enriched on the top of the polycrystalline film may introduce additional trap states, which manipulate the photoluminescence performance and dynamics of the as-prepared perovskite films in an opposite manner. Based on this finding, the strategy of optimizing the photophysical properties of the host 3D perovskite through 2D/3D engineering is elaborated, paving the way for fabricating high-performance and high-stability perovskite polycrystalline films.

Tuning Dimensionality of Benzimidazole Aggregates by Using Tetraoctylammonium Bromide: Enhanced Electrochemiluminescence Studies

Exploring the depolymerization strategy of liposoluble luminophores in the aqueous phase is vital for the development of electrochemiluminescence (ECL). In this work, tetraoctylammonium bromide (TOAB) with four long hydrophobic chains and short hydrophilic ends is used as a template to limit the aggregation of benzimidazole (BIM). By adjusting the loading of BIM on the hydrophobic chains of TOAB, a two-dimensional lamellar BIM/TOAB is formed, the ECL intensity of which is 6.4 times higher than that of the aggregated BIM (H₂O₂ as the coreactant). In terms of ECL spectroscopies, cyclic voltammetry , ECL transients, and the adjustment of the scanning potential range, the ECL mechanism is thoroughly studied. This work provides a new way to depolymerize organic luminophores and reveals a possible pathway in the annihilation ECL mechanism.

Self-healing 2D/3D perovskite for efficient and stable p-i-n perovskite solar cells

Beyond the p-i-n perovskite solar cell's high-power conversion efficiency (PCE), its moisture instability is the most challenging factor in its commercialization. Recently, the innovative use of three and two-dimensional multi-structures, by creating a barrier against the penetration of moisture and oxygen, has played a very influential role in improving the PSC's long-term stability. Here, a new strategy, the anti-solvent quenching method, is used to construct multi-structure perovskite by involving cetyltrimethylammonium bromide (CTAB) as an active agent. The solar cell efficiency is significantly improved during the perovskite formation on the substrate by creating a multidimensional (2D/3D) heterojunction perovskite. The synergistic role of using 2D/3D heterojunction perovskite structures led to the 29.2% improvement (14.58-18.84) in the PCE. The attractive ability of the 2D/3D active layer in self-healing has increased the perovskite's long-term stability under harsh environmental conditions.

Butanediammonium Salt Additives for Increasing Functional and Operando Stability of Light-Harvesting Materials in Perovskite Solar Cells

Organic diammonium cations are a promising component of both layered (2D) and conventional (3D) hybrid halide perovskites in terms of increasing the stability of perovskite solar cells (PSCs). We investigated the crystallization ability of phase-pure 2D perovskites based on 1,4-butanediammonium iodide (BDAI2) with the layer thicknesses n = 1, 2, 3 and, for the first time, revealed the presence of a persistent barrier to obtain BDA-based layered compounds with n > 1. Secondly, we introduced BDAI2 salt into 3D lead−iodide perovskites with different cation compositions and discovered a threshold-like nonmonotonic dependence of the perovskite microstructure, optoelectronic properties, and device performance on the amount of diammonium additive. The value of the threshold amount of BDAI2 was found to be ≤1%, below which bulk passivation plays the positive effect on charge carrier lifetimes, fraction of radiative recombination, and PSCs power conversion efficiencies (PCE). In contrast, the presence of any amount of diammonium salt leads to the sufficient enhancement of the photothermal stability of perovskite materials and devices, compared to the reference samples. The performance of all the passivated devices remained within the range of 50 to 80% of the initial PCE after 400 h of continuous 1 sun irradiation with a stabilized temperature of 65 °C, while the performance of the control devices deteriorated after 170 h of the experiment.

Interface Reconstruction from Ruddlesden-Popper Structures Impacts Stability in Lead Halide Perovskite Solar Cells

The impact of the bulky-cation-modified interfaces on halide perovskite solar cell stability is underexplored. In this work, the thermal instability of the bulky-cation interface layers used in the state-of-the-art solar cells is demonstrated. X-ray photoelectron spectroscopy and synchrotron-based grazing-incidence X-ray scattering measurements reveal significant changes in the chemical composition and structure at the surface of these films that occur under thermal stress. The changes impact charge-carrier dynamics and device operation, as shown in transient photoluminescence, excitation correlation spectroscopy, and solar cells. The type of cation used for surface treatment affects the extent of these changes, where long carbon chains provide more stable interfaces. These results highlight that prolonged annealing of the treated interfaces is critical to enable reliable reporting of performances and to drive the selection of different bulky cations.

Metal Halide Perovskite/Electrode Contacts in Charge-Transporting-Layer-Free Devices

Metal halide perovskites have drawn substantial interest in optoelectronic devices in the past decade. Perovskite/electrode contacts are crucial for constructing high-performance charge-transporting-layer-free perovskite devices, such as solar cells, field-effect transistors, artificial synapses, memories, etc. Many studies have evidenced that the perovskite layer can directly contact the electrodes, showing abundant physicochemical, electronic, and photoelectric properties in charge-transporting-layer-free perovskite devices. Meanwhile, for perovskite/metal contacts, some critical interfacial physical and chemical processes are reported, including band bending, interface dipoles, metal halogenation, and perovskite decomposition induced by metal electrodes. Thus, a systematic summary of the role of metal halide perovskite/electrode contacts on device performance is essential. This review summarizes and discusses charge carrier dynamics, electronic band engineering, electrode corrosion, electrochemical metallization and dissolution, perovskite decomposition, and interface engineering in perovskite/electrode contacts-based electronic devices for a comprehensive understanding of the contacts. The physicochemical, electronic, and morphological properties of various perovskite/electrode contacts, as well as relevant engineering techniques, are presented. Finally, the current challenges are analyzed, and appropriate recommendations are put forward. It can be expected that further research will lead to significant breakthroughs in their application and promote reforms and innovations in future solid-state physics and materials science.

Thermal- and Light-Induced Evolution of the 2D/3D Interface in Lead-Halide Perovskite Films

The instability of halide perovskites toward moisture is one of the main challenges in the field that needs to be overcome to successfully integrate these materials in commercially viable technologies. One of the most popular ways to ensure device stability is to form 2D/3D interfaces by using bulky organic molecules on top of the 3D perovskite thin film. Despite its promise, it is unclear whether this approach is able to avoid 3D bulk degradation under accelerated aging conditions, i.e., thermal stress and light soaking. In this regard, it is crucial to know whether the interface is structurally and electronically stable or not. In this work, we use the bulky phenethylammonium cation (PEA⁺) to form 2D layers on top of 3D single- and triple-cation halide perovskite films. The dynamical change of the 2D/3D interface is monitored under thermal stress and light soaking by in situ photoluminescence. We find that under pristine conditions the large organic cation diffuses only in 3D perovskite thin films of poor structural stability, i.e., single-cation MAPbI₃. The same diffusion and a dynamical change of the crystalline structure of the 2D/3D interface are observed even on high-quality 3D films, i.e., triple-cation MAFACsPbI₃, upon thermal stress at 85 °C and light soaking. Importantly, under such conditions, the resistance of the thin film to moisture is lost.

Modelling Interfaces in Thin-Film Photovoltaic Devices

Developing effective device architectures for energy technologies-such as solar cells, rechargeable batteries or fuel cells-does not only depend on the performance of a single material, but on the performance of multiple materials working together. A key part of this is understanding the behaviour at the interfaces between these materials. In the context of a solar cell, efficient charge transport across the interface is a pre-requisite for devices with high conversion efficiencies. There are several methods that can be used to simulate interfaces, each with an in-built set of approximations, limitations and length-scales. These methods range from those that consider only composition (e.g. data-driven approaches) to continuum device models (e.g. drift-diffusion models using the Poisson equation) and ab-initio atomistic models (developed using e.g. density functional theory). Here we present an introduction to interface models at various levels of theory, highlighting the capabilities and limitations of each. In addition, we discuss several of the various physical and chemical processes at a heterojunction interface, highlighting the complex nature of the problem and the challenges it presents for theory and simulation.

Halide perovskite dynamics at work: Large cations at 2D-on-3D interfaces are mobile

SignificanceSurface engineering of halide perovskites (HaPs), semiconductors with amazing optoelectronic properties, is critical to improve the performance and ambient stability of HaP-based solar cells and light emitting diodes (LEDs). Ultrathin layers of two-dimensional (2D) analogs of the three-dimensional (3D) HaPs are particularly attractive for this because of their chemical similarities but higher ambient stability. But do such 2D/3D interfaces actually last, given that ions in HaPs move readily-i.e., what happens at those interfaces on the atomic scale? A special electron microscopy, which as a bonus also reveals the true conditions for nondestructive analysis, shows that the large ions that are a necessary part of the 2D films can move into the 3D HaP, a fascinating illustration of panta rei in HaPs.

Growth and Degradation Kinetics of Organic-Inorganic Hybrid Perovskite Films Determined by In Situ Grazing-Incidence X-Ray Scattering Techniques

Organic-inorganic halide perovskite (OIHP) solar cells hold a great promise for commercial breakthrough since their power conversion efficiency has been pushed beyond the mark of 25%, making them capable of competing with traditional crystalline silicon solar cells. The key to achieve efficient and stable perovskite solar cells is inherently related to the film morphology. The understanding of the kinetic processes of film formation and degradation opens up possibilities to tailor the film morphology via the regulation of precursor and processing parameters. In situ grazing-incidence X-ray scattering (GIXS) techniques allow for tracking the morphology evolution of thin films at different length scales and with high temporal resolution. In this review, the selected examples for application of in situ grazing-incidence wide-angle X-ray scattering and grazing-incidence small-angle X-ray scattering techniques to the growth and stability of OIHPs are summarized after a brief introduction to both techniques, highlighting particularly the morphological evolution of perovskite films over time. Then the correlated mathematical models are reviewed to give a toolbox for analyzing the mechanisms of film formation and degradation. Thus, an overview on the in situ GIXS methods is linked to the research of OIHP kinetics.

Mechanistic Insights into the Role of the Bis(trifluoromethanesulfonyl)imide Ion in Coevaporated p-i-n Perovskite Solar Cells

Hybrid lead halide perovskites have reached comparable efficiencies to state-of-the-art silicon solar cell technologies. However, a remaining key challenge toward commercialization is the resolution of the perovskite device instability. In this work, we identify for the first time the mobile nature of bis(trifluoromethanesulfonyl)imide (TFSI-), a typical anion extensively employed in p-type dopants for 2,2'7,7'-tetrakis(N,N-di-p-methoxyphenylamine)-9,9'spirofluorene (spiro-OMeTAD). We demonstrate that TFSI- can migrate through the perovskite layer via the grain boundaries and accumulate at the perovskite/electron-transporting layer (ETL) interface. Our findings reveal that the migration of TFSI- enhances the device performance and stability, resulting in highly stable p-i-n cells that retain 90% of their initial performance after 1600 h of continuous testing. Our systematic study, which targeted the effect of the nature of the dopant and its concentration, also shows that TFSI- acts as a dynamic defect-healing agent, which self-passivates the perovskite crystal defects during the migration process and thereby decreases nonradiative recombination pathways.

Solution-processed two-dimensional materials for next-generation photovoltaics

In the ever-increasing energy demand scenario, the development of novel photovoltaic (PV) technologies is considered to be one of the key solutions to fulfil the energy request. In this context, graphene and related two-dimensional (2D) materials (GRMs), including nonlayered 2D materials and 2D perovskites, as well as their hybrid systems, are emerging as promising candidates to drive innovation in PV technologies. The mechanical, thermal, and optoelectronic properties of GRMs can be exploited in different active components of solar cells to design next-generation devices. These components include front (transparent) and back conductive electrodes, charge transporting layers, and interconnecting/recombination layers, as well as photoactive layers. The production and processing of GRMs in the liquid phase, coupled with the ability to "on-demand" tune their optoelectronic properties exploiting wet-chemical functionalization, enable their effective integration in advanced PV devices through scalable, reliable, and inexpensive printing/coating processes. Herein, we review the progresses in the use of solution-processed 2D materials in organic solar cells, dye-sensitized solar cells, perovskite solar cells, quantum dot solar cells, and organic-inorganic hybrid solar cells, as well as in tandem systems. We first provide a brief introduction on the properties of 2D materials and their production methods by solution-processing routes. Then, we discuss the functionality of 2D materials for electrodes, photoactive layer components/additives, charge transporting layers, and interconnecting layers through figures of merit, which allow the performance of solar cells to be determined and compared with the state-of-the-art values. We finally outline the roadmap for the further exploitation of solution-processed 2D materials to boost the performance of PV devices.

Advances and Challenges in Two-Dimensional Organic-Inorganic Hybrid Perovskites Toward High-Performance Light-Emitting Diodes

Two-dimensional (2D) perovskites are known as one of the most promising luminescent materials due to their structural diversity and outstanding optoelectronic properties. Compared with 3D perovskites, 2D perovskites have natural quantum well structures, large exciton binding energy (Eb) and outstanding thermal stability, which shows great potential in the next-generation displays and solid-state lighting. In this review, the fundamental structure, photophysical and electrical properties of 2D perovskite films were illustrated systematically. Based on the advantages of 2D perovskites, such as special energy funnel process, ultra-fast energy transfer, dense film and low efficiency roll-off, the remarkable achievements of 2D perovskite light-emitting diodes (PeLEDs) are summarized, and exciting challenges of 2D perovskite are also discussed. An outlook on further improving the efficiency of pure-blue PeLEDs, enhancing the operational stability of PeLEDs and reducing the toxicity to push this field forward was also provided. This review provides an overview of the recent developments of 2D perovskite materials and LED applications, and outlining challenges for achieving the high-performance devices.

Multication perovskite 2D/3D interfaces form via progressive dimensional reduction

Many of the best-performing perovskite photovoltaic devices make use of 2D/3D interfaces, which improve efficiency and stability – but it remains unclear how the conversion of 3D-to-2D perovskite occurs and how these interfaces are assembled. Here, we use in situ Grazing-Incidence Wide-Angle X-Ray Scattering to resolve 2D/3D interface formation during spin-coating. We observe progressive dimensional reduction from 3D to n = 3 → 2 → 1 when we expose (MAPbBr₃)_0.05(FAPbI₃)_0.95 perovskites to vinylbenzylammonium ligand cations. Density functional theory simulations suggest ligands incorporate sequentially into the 3D lattice, driven by phenyl ring stacking, progressively bisecting the 3D perovskite into lower-dimensional fragments to form stable interfaces. Slowing the 2D/3D transformation with higher concentrations of antisolvent yields thinner 2D layers formed conformally onto 3D grains, improving carrier extraction and device efficiency (20% 3D-only, 22% 2D/3D). Controlling this progressive dimensional reduction has potential to further improve the performance of 2D/3D perovskite photovoltaics.

Many best-performing perovskite photovoltaics use 2D/3D interfaces to improve efficiency and stability, yet the mechanism of interface assembly is unclear. Here, Proppe et al. use in-situ GIWAXS to resolve this transformation, observing progressive dimensional reduction from 3D to 2D perovskites.

Insights into Microscopic Crystal Growth Dynamics of CH3NH3PbI3 under a Laser Deposition Process Revealed by In Situ X-ray Diffraction

The process dynamics for the vacuum deposition of methylammonium lead iodide (MAPbI₃) perovskite was analyzed by in situ X-ray diffraction using synchrotron radiation. MAPbI₃ was fabricated by alternatingly supplying PbI₂ and methylammonium iodide via a laser deposition system installed at the synchrotron beamline BL46XU at SPring-8, and in situ crystallization analysis was conducted. Microscopic insights into the crystallization were obtained, including observation of Laue oscillation during the PbI₂ growth and octahedral unit (PbI₆) rotation during the transformation into perovskite. On the basis of this analysis, conditions that favor the construction of atomically flat MAPbI₃ perovskite films were deduced.

Organic Ammonium Halide Modulators as Effective Strategy for Enhanced Perovskite Photovoltaic Performance

Despite rapid improvements in efficiency, long-term stability remains a challenge limiting the future up-scaling of perovskite solar cells (PSCs). Although several approaches have been developed to improve the stability of PSCs, applying ammonium passivation materials in bilayer configuration PSCs has drawn intensive research interest due to the potential of simultaneously improving long-term stability and boosting power conversion efficiency (PCE). This review focuses on the recent advances of improving n-i-p PSCs photovoltaic performance by employing ammonium halide-based molecular modulators. The first section briefly summarizes the challenges of perovskite materials by introducing the degradation mechanisms associated with the hygroscopic nature and ion migration issues. Then, recent reports regarding the roles of overlayers formed from ammonium-based passivation agents are discussed on the basis of ligand and halide effects. This includes both the formation of 2D perovskite films as well as purely organic passivating layers. Finally, the last section provides future perspectives on the use of organic ammonium halides within bilayer-architecture PSCs to improve the photovoltaic performances. Overall, this review provides a roadmap on current demands and future research directions of molecular modulators to address the critical limitations of PSCs, to mitigate the major barriers on the pathway toward future up-scaling applications.

Layered Perovskites Enhanced Perovskite Photodiodes

Recently, two-dimensional layered perovskites have emerged as effective additives for stabilizing conventional three-dimensional metal halide perovskites. With the addition of layered perovskites, the perovskite-based devices also exhibited enhanced optoelectronic properties, such as reduced nonradiative recombination and ionic migration, strengthened crystallinity, and anisotropic charge transport. However, the influence of the large organic cations on the performance metrics of the photodiodes is not fully understood. In this work, we systematically investigate the device performance and related optoelectronic features of the layered perovskite-enhanced perovskite photodiodes. In particular, with the addition of large organic cations to the FA_0.83Cs_0.17PbI₃ perovskite matrix, the devices exhibited reduced dark current and noise, increased detectivity of >10¹³ Jones, and a consistent high speed of <100 ns. More importantly, the layered perovskite-enhanced photodiodes exhibited less hysteresis and higher breakdown voltages.

Metal halide perovskites for light-emitting diodes

Metal halide perovskites have shown promising optoelectronic properties suitable for light-emitting applications. The development of perovskite light-emitting diodes (PeLEDs) has progressed rapidly over the past several years, reaching high external quantum efficiencies of over 20%. In this Review, we focus on the key requirements for high-performance PeLEDs, highlight recent advances on materials and devices, and emphasize the importance of reliable characterization of PeLEDs. We discuss possible approaches to improve the performance of blue and red PeLEDs, increase the long-term operational stability and reduce toxicity hazards. We also provide an overview of the application space made possible by recent developments in high-efficiency PeLEDs.

Semiconductor physics of organic-inorganic 2D halide perovskites

Achieving technologically relevant performance and stability for optoelectronics, energy conversion, photonics, spintronics and quantum devices requires creating atomically precise materials with tailored homo- and hetero-interfaces, which can form functional hierarchical assemblies. Nature employs tunable sequence chemistry to create complex architectures, which efficiently transform matter and energy, however, in contrast, the design of synthetic materials and their integration remains a long-standing challenge. Organic-inorganic two-dimensional halide perovskites (2DPKs) are organic and inorganic two-dimensional layers, which self-assemble in solution to form highly ordered periodic stacks. They exhibit a large compositional and structural phase space, which has led to novel and exciting physical properties. In this Review, we discuss the current understanding in the structure and physical properties of 2DPKs from the monolayers to assemblies, and present a comprehensive comparison with conventional semiconductors, thereby providing a broad understanding of low-dimensional semiconductors that feature complex organic-inorganic hetero-interfaces.

How machine learning can help select capping layers to suppress perovskite degradation

Environmental stability of perovskite solar cells (PSCs) has been improved by trial-and-error exploration of thin low-dimensional (LD) perovskite deposited on top of the perovskite absorber, called the capping layer. In this study, a machine-learning framework is presented to optimize this layer. We featurize 21 organic halide salts, apply them as capping layers onto methylammonium lead iodide (MAPbI₃) films, age them under accelerated conditions, and determine features governing stability using supervised machine learning and Shapley values. We find that organic molecules' low number of hydrogen-bonding donors and small topological polar surface area correlate with increased MAPbI₃ film stability. The top performing organic halide, phenyltriethylammonium iodide (PTEAI), successfully extends the MAPbI₃ stability lifetime by 4 ± 2 times over bare MAPbI₃ and 1.3 ± 0.3 times over state-of-the-art octylammonium bromide (OABr). Through characterization, we find that this capping layer stabilizes the photoactive layer by changing the surface chemistry and suppressing methylammonium loss.