Realizing 17.5% Efficiency Flexible Organic Solar Cells via Atomic-Level Chemical Welding of Silver Nanowire Electrodes

Metal nanowire-based transparent electrode for flexible and stretchable optoelectronic devices

High-quality transparent electrodes are indispensable components of flexible optoelectronic devices as they guarantee sufficient light transparency and electrical conductivity. Compared to commercial indium tin oxide, metal nanowires are considered ideal candidates as flexible transparent electrodes (FTEs) owing to their superior optoelectronic properties, excellent mechanical flexibility, solution treatability, and higher compatibility with semiconductors. However, certain key challenges associated with material preparation and device fabrication remain for the practical application of metal nanowire-based electrodes. In this review, we discuss state-of-the-art solution-processed metal nanowire-based FTEs and their applications in flexible and stretchable optoelectronic devices. Specifically, the important properties of FTEs and a cost-benefit analysis of existing technologies are introduced, followed by a summary of the synthesis strategy, key properties, and fabrication technologies of the nanowires. Subsequently, we explore the applications of metal-nanowire-based FTEs in different optoelectronic devices including solar cells, photodetectors, and light-emitting diodes. Finally, the current status, future challenges, and emerging strategies in this field are presented.

Heterogeneous Nucleating Agent for High-Boiling-Point Nonhalogenated Solvent-Processed Organic Solar Cells and Modules

High-boiling-point nonhalogenated solvents are superior solvents to produce large-area organic solar cells (OSCs) in industry because of their wide processing window and low toxicity; while, these solvents with slow evaporation kinetics will lead excessive aggregation of state-of-the-art small molecule acceptors (e.g. L8-BO), delivering serious efficiency losses. Here, a heterogeneous nucleating agent strategy is developed by grafting oligo (ethylene glycol) side-chains on L8-BO (BTO-BO). The formation energy of the obtained BTO-BO; while, changing from liquid in a solvent to a crystalline phase, is lower than that of L8-BO irrespective of the solvent type. When BTO-BO is added as the third component into the active layer (e.g. PM6:L8-BO), it easily assembles to form numerous seed crystals, which serve as nucleation sites to trigger heterogeneous nucleation and increase nucleation density of L8-BO through strong hydrogen bonding interactions even in high-boiling-point nonhalogenated solvents. Therefore, it can effectively suppress excessive aggregation during growth, achieving ideal phase-separation active layer with small domain sizes and high crystallinity. The resultant toluene-processed OSCs exhibit a record power conversion efficiency (PCE) of 19.42% (certificated 19.12%) with excellent operational stability. The strategy also has superior advantages in large-scale devices, showing a 15.03-cm2 module with a record PCE of 16.35% (certificated 15.97%).

Highly Stable Silver Nanowire Plasmonic Electrodes for Flexible Polymer Light-Emitting Devices

Silver nanowire (AgNW) transparent electrodes are considered as a promising candidate for applications in flexible optoelectronic devices. However, it remains a great challenge to obtain flexible AgNW electrodes with excellent optoelectrical properties and mechanical flexibility. Here, highly stable Ag nanoparticle (AgNP)-enhanced plasmonic AgNW electrodes are demonstrated via the controllable in situ growth of AgNPs at the AgNW junctions and introduction of an l-histidine (l-His) wrapping layer. The flexible transparent electrodes of AgNW-AgNP/l-His possess a low sheet resistance (Rsh) of ∼17.5 Ω sq-1, a high transmittance of ∼92.5% (550 nm), and a robust mechanical stability (100,000 bending cycles). Benefiting from plasmon-coupling effects, flexible polymer light-emitting devices (FPLEDs) with AgNW-AgNP/l-His electrodes present a current efficiency (CE) of ∼14.8 cd A-1 and an external quantum efficiency (EQE) of ∼5.6%, constituting ∼80% and ∼75% increases compared to those of the reference devices with AgNW electrodes, respectively. Additionally, the laminated flexible transparent PLEDs (FT-PLEDs) are demonstrated by integrating polydimethylsiloxane/AgNW-AgNP anodes by a soft lamination process. The FT-PLEDs present a CE of ∼7.1 cd A-1 (cathode side: ∼3.9 cd A-1; anode side: ∼3.2 cd A-1) and an EQE of ∼2.7% (cathode side: ∼1.5%; anode side: ∼1.2%). Furthermore, the FPLEDs and FT-PLEDs exhibit robust mechanical durability, maintaining ∼89% and ∼86% of their initial luminance after 1000 bending cycles at a bending radius of 2 mm, respectively. This work opens up a new avenue for the development of high performance and stable flexible optoelectronic devices.

Interfacial-Assembly-Induced In Situ Transformation from Aligned 1D Nanowires to Quasi-2D Nanofilms

As the dimensionality of materials generally affects their characteristics, thin films composed of low-dimensional nanomaterials, such as nanowires (NWs) or nanoplates, are of great importance in modern engineering. Among various bottom-up film fabrication strategies, interfacial assembly of nanoscale building blocks holds great promise in constructing large-scale aligned thin films, leading to emergent or enhanced collective properties compared to individual building blocks. As for 1D nanostructures, the interfacial self-assembly causes the morphology orientation, effectively achieving anisotropic electrical, thermal, and optical conduction. However, issues such as defects between each nanoscale building block, crystal orientation, and homogeneity constrain the application of ordered films. The precise control of transdimensional synthesis and the formation mechanism from 1D to 2D are rarely reported. To meet this gap, we introduce an interfacial-assembly-induced interfacial synthesis strategy and successfully synthesize quasi-2D nanofilms via the oriented attachment of 1D NWs on the liquid interface. Theoretical sampling and simulation show that NWs on the liquid interface maintain their lowest interaction energy for the ordered crystal plane (110) orientation and then rearrange and attach to the quasi-2D nanofilm. This quasi-2D nanofilm shows enhanced electric conductivity and unique optical properties compared with its corresponding 1D geometry materials. Uncovering these growth pathways of the 1D-to-2D transition provides opportunities for future material design and synthesis at the interface.

Balancing Flexible Side Chains on 2D Conjugated Acceptors Enables High-Performance Organic Solar Cell

Balancing the rigid backbones and flexible side chains of light-harvesting materials is crucially important to reach optimized intermolecular packing, micromorphology, and thus photovoltaic performance of organic solar cells (OSCs). Herein, based on a distinctive CH-series acceptor platform with 2D conjugation extended backbones, a series of nonfullerene acceptors (CH-6F-Cn) are synthesized by delicately tuning the lengths of flexible side chains from n-octyl to n-amyl. A systemic investigation has revealed that the variation of the side chain's length can not only modulate intermolecular packing modes and crystallinity but also dramatically improve the micromorphology of the active layer and eventual photovoltaic parameters of OSCs. Consequently, the highest PCE of 18.73% can be achieved by OSCs employing D18:PM6:CH-6F-C8 as light-harvesting materials.

Advances in Stretchable Organic Photovoltaics: Flexible Transparent Electrodes and Deformable Active Layer Design

Stretchable organic photovoltaics (OPVs) have attracted significant attention as promising power sources for wearable electronic systems owing to their superior robustness under repetitive tensile strains and their good compatibility. However, reconciling a high power-conversion efficiency and a reasonable flexibility is a tremendous challenge. In addition, the development of stretchable OPVs must be accelerated to satisfy the increasing requirements of niche markets for mechanical robustness. Stretchable OPV devices can be classified as either structurally or intrinsically stretchable. This work reviews recent advances in stretchable OPVs, including the design of mechanically robust transparent electrodes, photovoltaic materials, and devices. Initially, an overview of the characteristics and recent research progress in the areas of structurally and intrinsically stretchable OPVs is provided. Subsequently, research into flexible and stretchable transparent electrodes that directly affect the performances of stretchable OPVs is summarized and analyzed. Overall, this review aims to provide an in-depth understanding of the intrinsic properties of highly efficient and deformable active materials, while also emphasizing advanced strategies for simultaneously improving the photovoltaic performance and mechanical flexibility of the active layer, including material design, multi-component settings, and structural optimization.

Organic indoor PV: vanishing surface recombination allows for robust device architecture

As a promising candidate to drive low-power, off-grid applications, organic indoor photovoltaics are beginning to attract research and commercial attention. In organic photovoltaic devices, charge transport layers are often used to promote the extraction of majority carriers, while blocking minority carriers. They can however be a source of device degradation and introduce additional complexity to the fabrication of the device stack. Here, a simplified, yet performant indoor OPV architecture is demonstrated with extended absorber thickness and without electron transport layer (ETL). We show that the diminished impact of the ETL on indoor OPV results from a drastically reduced surface recombination in thick absorber devices. However, the ETL remains important under strong, outdoor illumination, since in that case the reduced surface recombination is overwhelmed by bulk recombination. The proposed simplified device architecture with thick absorber (>500 nm) has great potential in large-scale production of indoor OPV.

Stability of organic solar cells: toward commercial applications

Organic solar cells (OSCs) have attracted a great deal of attention in the field of clean solar energy due to their advantages of transparency, flexibility, low cost and light weight. Introducing them to the market enables seamless integration into buildings and windows, while also supporting wearable, portable electronics and internet-of-things (IoT) devices. With the development of photovoltaic materials and the optimization of fabrication technology, the power conversion efficiencies (PCEs) of OSCs have rapidly improved and now exceed 20%. However, there is a significant lack of focus on material stability and device lifetime, causing a severe hindrance to commercial applications. In this review, we carefully review important strategies employed to improve the stability of OSCs over the past three years from the perspectives of material design and device engineering. Furthermore, we analyze and discuss the current important progress in terms of air, light, thermal and mechanical stability. Finally, we propose the future research directions to overcome the challenges in achieving highly stable OSCs. We expect that this review will contribute to solving the stability problem of OSCs, eventually paving the way for commercial applications in the near future.

Advances in Smart Photovoltaic Textiles

Energy harvesting textiles have emerged as a promising solution to sustainably power wearable electronics. Textile-based solar cells (SCs) interconnected with on-body electronics have emerged to meet such needs. These technologies are lightweight, flexible, and easy to transport while leveraging the abundant natural sunlight in an eco-friendly way. In this Review, we comprehensively explore the working mechanisms, diverse types, and advanced fabrication strategies of photovoltaic textiles. Furthermore, we provide a detailed analysis of the recent progress made in various types of photovoltaic textiles, emphasizing their electrochemical performance. The focal point of this review centers on smart photovoltaic textiles for wearable electronic applications. Finally, we offer insights and perspectives on potential solutions to overcome the existing limitations of textile-based photovoltaics to promote their industrial commercialization.

An ITO-Free Kesterite Solar Cell

Photovoltaic thin film solar cells based on kesterite Cu2 ZnSn(S, Se)4 (CZTSSe) have reached 13.8% sunlight-to-electricity conversion efficiency. However, this efficiency is still far from the Shockley-Queisser radiative limit and is hindered by the significant deficit in open circuit voltage (VOC ). The presence of high-density interface states between the absorber layer and buffer or window layer leads to the recombination of photogenerated carriers, thereby reducing effective carrier collection. To tackle this issue, a new window structure ZnO/AgNW/ZnO/AgNW (ZAZA) comprising layers of ZnO and silver nanowires (AgNWs) is proposed. This structure offers a simple and low-damage processing method, resulting in improved optoelectronic properties and junction quality. The ZAZA-based devices exhibit enhanced VOC due to the higher built-in voltage (Vbi ) and reduced interface recombination compared to the usual indium tin oxide (ITO) based structures. Additionally, improved carrier collection is demonstrated as a result of the shortened collection paths and the more uniform carrier lifetime distribution. These advances enable the fabrication of the first ITO-free CZTSSe solar cells with over 10% efficiency without an anti-reflective coating.

Selectively Modulating Componential Morphologies of Bulk Heterojunction Organic Solar Cells

Achieving precise control over the nanoscale morphology of bulk heterojunction films presents a significant challenge for the conventional post-treatments employed in organic solar cells (OSCs). In this study, a near-infrared photon-assisted annealing (NPA) strategy is developed for fabricating high-performance OSCs under mild processing conditions. It is revealed a top NIR light illumination, together with the bottom heating, enables the selective tuning of the molecular arrangement and assembly of narrow bandgap acceptors in polymer networks to achieve optimal morphologies, as well as the acceptor-rich top surface of active layers. The derived OSCs exhibit a remarkable power conversion efficiency (PCE) of 19.25%, representing one of the highest PCEs for the reported binary OSCs so far. Moreover, via the NPA strategy, it has succeeded in accessing top-illuminated flexible OSCs using thermolabile polyethylene terephthalate from mineral water bottles, displaying excellent mechanical stabilities. Overall, this work will hold the potential to develop organic solar cells under mild processing with various substrates.

Enhancing Conductivity of Silver Nanowire Networks through Surface Engineering Using Bidentate Rigid Ligands

Solution processable metallic nanomaterials present a convenient way to fabricate conductive structures, which are necessary in all electronic devices. However, they tend to require post-treatments to remove the bulky ligands around them to achieve high conductivity. In this work, we present a method to formulate a post-treatment free conductive silver nanowire ink by controlling the type of ligands around the silver nanowires. We found that bidentate ligands with a rigid molecular structure were effective in improving the conductivity of the silver nanowire networks as they could maximize the number of linkages between neighboring nanowires. In addition, DFT calculations also revealed that ligands with good LUMO to silver energy alignment were more effective. Because of these reasons, fumaric acid was found to be the most effective ligand and achieved a large reduction in sheet resistance of 70% or higher depending on the nanowire network density. The concepts elucidated from this study would also be applicable to other solution processable nanomaterials systems such as quantum dots for photovoltaics or LEDs which also require good charge transport being neighboring nanoparticles.

Flexible Transparent Electrode Based on Ag Nanowires: Ag Nanoparticles Co-Doped System for Organic Light-Emitting Diodes

Flexible organic light-emitting diodes (FOLEDs) have promising potential for future wearable applications because of their exceptional mechanical flexibility. Silver nanowire (Ag NW) networks are the most promising candidates to replace indium tin oxide (ITO), which is limited by its poor bendability. In this study, three different methods including methanol impregnation, argon plasma treatment, and ultraviolet radiation were used to reduce the junction resistance of Ag NWs to optimize the flexible transparent electrodes (FTEs); which were prepared using Ag NWs and poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT: PSS). Then, the optoelectronic properties of the FTEs were further improved by using a co-doped system of silver nanowires and silver nanoparticles (Ag NPs), the structure of which consisted of PET/Ag NWs: Ag NPs/PEDOT: PSS/DMSO. The largest FOM value of 1.42 × 10-2 ohm-1 and a low sheet resistance value of 13.86 ohm/sq were obtained using the optimized FTEs. The prepared FOLED based on the optimized FTEs had a luminous efficiency of 6.04 cd/A and a maximum EQE of 1.92%, and exhibited no observed decline in efficiency when reaching maximum luminance. After 500 bending tests, the luminance still reached 82% of the original value. It is demonstrated that the FTEs prepared via the co-doped system have excellent optoelectronic properties as well as high mechanical stability.

Effect of sulphidation process on the structure, morphology and optical properties of GO/AgNWs composites

In this study, composite materials composed of graphene oxide (GO) synthesized by a modified Hummers' method and silver nanowires (AgNWs) synthesized by a modified polyol method were prepared. The prepared composites were subjected to sulfidation under the influence of H2S gas. Structural changes in the samples were evaluated using X-ray diffraction (XRD). The binding nature of the composite was characterized using FT-IR spectroscopy. Optical properties and band gap values were investigated using ultraviolet-visible (UV-Vis) spectroscopy. The morphology of the composites was analyzed by transmission electron microscopy (TEM). A simple method using H2S gas was applied for the sulphidation process of the samples. The sulfidation process was successful under the influence of H2S gas, resulting in an increased distance between the GO layers and a decrease in the band gap value for the composite post-sulfidation. In addition, AgNWs were observed to decompose into Ag2S nanoparticles under the influence of H2S gas. It was determined that the value of the band gap of the sample changes because of sulphidation.

Efficient Flexible Fabric-Based Top-Emitting Polymer Light-Emitting Devices for Wearable Electronics

Low-cost fabric-based top-emitting polymer light-emitting devices (Fa-TPLEDs) have aroused increasing attention due to their remarkable potential applications in wearable displays. However, it is still challenging to realize efficient all-solution-processed devices from bottom electrodes to top electrodes with large-scale fabrication. Here, a smooth reflective Ag cathode integrated on fabric by one-step silver mirror reaction and a composite transparent anode of polydimethylsiloxane/silver nanowires/poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) via a water-assisted peeling method are presented, both of which possess excellent optoelectrical properties and robust mechanical flexibility. The Fa-TPLEDs are constructed by spin-coating functional layers on the bottom reflective cathodes and laminating the top transparent anodes. The Fa-TPLEDs show a current efficiency of 16.3 cd A-1 , an external quantum efficiency of 4.9% and angle-independent electroluminescence spectra. In addition, the Fa-TPLEDs possess excellent mechanical stability, maintaining a current efficiency of 14.3 cd A-1 after 200 bending cycles at a radius of 4 mm. The results demonstrate that the integration of solution-processed reflective cathodes and transparent anodes sheds light on a new avenue to construct low-cost and efficient fabric-based devices, showing great potential applications in emerging smart flexible/wearable electronics.

Thorough Optimization for Intrinsically Stretchable Organic Photovoltaics

The development of intrinsically stretchable organic photovoltaics (is-OPVs) with a high efficiency is of significance for practical application. However, their efficiencies lag far behind those of rigid or even flexible counterparts. To address this issue, an advanced top-illuminated OPV is designed and fabricated, which is intrinsically stretchable and has a high performance, through systematic optimizations from material to device. First, the stretchability of the active layer is largely increased by adding a low-elastic-modulus elastomer of styrene-ethylene-propylene-styrene tri-block copolymer (SEPS). Second, the stretchability and conductivity of the opaque electrode are enhanced by a conductive polymer/metal (denoted as M-PH1000@Ag) composite electrode strategy. Third, the optical and electrical properties of a sliver nanowire transparent electrode are improved by a solvent vapor annealing strategy. High-performance is-OPVs are successfully fabricated with a top-illuminated structure, which provides a record-high efficiency of 16.23%. Additionally, by incorporating 5-10% elastomer, a balance between the efficiency and stretchability of the is-OPVs is achieved. This study provides valuable insights into material and device optimizations for high-efficiency is-OPVs, with a low-cost production and excellent stretchability, which indicates a high potential for future applications of OPVs.

Optimized Crystal Framework by Asymmetric Core Isomerization in Selenium-Substituted Acceptor for Efficient Binary Organic Solar Cells

Both the regional isomerization and selenium-substitution of the small molecular acceptors (SMAs) play significant roles in developing efficient organic solar cells (OSCs), while their synergistic effects remain elusive. Herein, we developed three isomeric SMAs (S-CSeF, A-ISeF, and A-OSeF) via subtly manipulating the mono-selenium substituted position (central, inner, or outer) and type of heteroaromatic ring on the central core by synergistic strategies for efficient OSCs, respectively. Crystallography of asymmetric A-OSeF presents a closer intermolecular π-π stacking and more ordered 3-dimensional network packing and efficient charge-hopping pathways. With the successive out-shift of the mono-selenium substituted position, the neat films give a slightly wider band gap and gradually higher crystallinity and electron mobility. The PM1 : A-OSeF afford favourable fibrous phase separation morphology with more ordered molecular packing and efficient charge transportation compared to the other two counterparts. Consequently, the A-OSeF-based devices achieve a champion efficiency of 18.5 %, which represents the record value for the reported selenium-containing SMAs in binary OSCs. Our developed precise molecular engineering of the position and type of selenium-based heteroaromatic ring of SMAs provides a promising synergistic approach to optimizing crystal stacking and boosting top-ranked selenium-containing SMAs-based OSCs.

Correlation of Broad Absorption Band with Small Singlet-Triplet Energy Gap in Organic Photovoltaics

Organic photovoltaics (OPV) are one of the most effective ways to harvest renewable solar energy, with the power conversion efficiency (PCE) of the devices soaring above 19 % when processed with halogenated solvents. The superior photocurrent of OPV over other emerging photovoltaics offers more opportunities to further improve the efficiency. Tailoring the absorption band of photoactive materials is an effective way to further enhance OPV photocurrent. However, the field has mostly been focusing on improving the near-infrared region photo-response, with the absorption shoulders in short-wavelength region (SWR) usually being neglected. Herein, by developing a series of non-fullerene acceptors (NFAs) with varied side-group conjugations, we observe an enhanced SWR absorption band with increased side-group conjugation length. The underpinning factors of how molecular structures and geometries improve SWR absorption are clearly elucidated through theoretical modelling and crystallography. Moreover, a clear relationship between the enhanced SWR absorption and reduced singlet-triplet energy gap is established, both of which are favorable for the OPV performance and can be tailored by rational structure design of NFAs. Finally, the rationally designed NFA, BO-TTBr, affords a decent PCE of 18.5 % when processed with a non-halogenated green solvent.

Ductile Oligomeric Acceptor-Modified Flexible Organic Solar Cells Show Excellent Mechanical Robustness and Near 18% Efficiency

High power conversion efficiency (PCE) and mechanical robustness are key requirements for wearable applications of organic solar cells (OSCs). However, almost all highly efficient photoactive films comprising polymer donors (PD ) and small molecule acceptors (SMAs) are mechanically brittle. In this study, highly efficient (PCE = 17.91%) and mechanically robust (crack-onset strain [COS] = 11.7%) flexible OSCs are fabricated by incorporating a ductile oligomeric acceptor (DOA) into the PD :SMA system, representing the most flexible OSCs to date. The photophysical, mechanical, and photovoltaic properties of D18:N3 with different DOAs are characterized. By introducing DOA DOY-C4 with a longer flexible alkyl linker and lower polymerization, the D18:N3:DOY-C4-based flexible OSCs exhibit a significantly higher PCE (17.91%) and 50% higher COS (11.7%) than the D18:N3-based device (PCE = 17.06%, COS = 7.8%). The flexible OSCs based on D18:N3:DOY-C4 retain 98% of the initial PCE after 2000 consecutive bending cycles, showing greater mechanical stability than the reference device (maintaining 89% of initial PCE). After careful investigation, it is hypothesized that the enhancement in mechanical properties is mainly due to the formation of tie chains or entanglement in the ternary blend films. These results demonstrate that DOAs have great potential for achieving high-performance flexible OSCs.

Solvent Welding-Based Methods Gently and Effectively Enhance the Conductivity of a Silver Nanowire Network

To enhance the conductivity of a silver nanowire (Ag NW) network, a facile solvent welding method was developed. Soaking a Ag NW network in ethylene glycol (EG) or alcohol for less than 15 min decreased the resistance about 70%. Further combined solvent processing via a plasmonic welding approach decreased the resistance about 85%. This was achieved by simply exposing the EG-soaked Ag NW network to a low-power blue light (60 mW/cm2). Research results suggest that poly(vinylpyrrolidone) (PVP) dissolution by solvent brings nanowires into closer contact, and this reduced gap distance between nanowires enhances the plasmonic welding effect, hence further decreasing resistance. Aside from this dual combination of methods, a triple combination with Joule heating welding induced by applying a current to the Ag NW network decreased the resistance about 96%. Although conductivity was significantly enhanced, our results showed that the melting at Ag NW junctions was relatively negligible, which indicates that the enhancement in conductivity could be attributed to the removal of PVP layers. Moreover, the approaches were quite gentle so any potential damage to Ag NWs or polymer substrates by overheating (e.g., excessive Joule heating) was avoided entirely, making the approaches suitable for application in devices using heat-sensitive materials.

Ultra Robust and Highly Efficient Flexible Organic Solar Cells with Over 18 % Efficiency Realized by Incorporating a Linker Dimerized Acceptor

The wearable application of flexible organic solar cells (f-OSCs) necessitates high power conversion efficiency (PCE) and mechanical robustness. However, photoactive films based on efficient non-fullerene small molecule acceptors (NF-SMAs) are typically brittle, leading to poor mechanical stability in devices. In this study, we achieved a remarkable PCE of 18.06 % in f-OSCs while maintaining ultrahigh mechanical robustness (with a crack-onset strain (COS) of higher than 11 %) by incorporating a linker dimerized acceptor (DOY-TVT). Compared to binary blends, ternary systems exhibit reduced non-radiative recombination, suppressed crystallization and diffusion of NF-SMAs, and improved load distribution across the chain networks, enabling the dissipation of the load energy. Thus, the ternary f-OSCs developed in this study achieved, high PCE and stability, surpassing binary OSCs. Moreover, the developed f-OSCs retained 97 % of the initial PCE even after 3000 bending cycles, indicating excellent mechanical stability (9.1 % higher than binary systems). Furthermore, the rigid device with inverted structure based on the optimal active layer exhibited a substantial increase in efficiency retention, with 89.6 % after 865 h at 85 °C and 93 % after more than 1300 h of shelf storage at 25 °C. These findings highlight the potential of the linker oligomer acceptor for realizing high-performing f-OSCs with ultrahigh mechanical robustness.

All-Polymer Solar Cells Sequentially Solution Processed from Hydrocarbon Solvent with a Thick Active Layer

Organic solar cells (OSCs) have gained increasing attention. Among the various directions in OSCs, all-polymer solar cells (all-PSCs) have emerged as a highly promising and currently active research area due to their excellent film formation properties, mechanical properties, and thermal stabilities. However, most of the high-efficiency all-PSCs are processed from chloroform with an active layer thickness of ~100 nm. In order to meet the requirements for industrialization, a thicker active layer processed from low-vapor pressure solvents (preferentially a hydrocarbon solvent) is strongly desired. Herein, we employ toluene (a hydrocarbon solvent with a much higher boiling point than chloroform) and a method known as sequential processing (SqP) to mitigate the rapid decline in efficiency with increasing film thickness. We show that SqP enables a more favorable vertical phase segregation that leads to less trap-assisted recombination and enhanced charge extraction and lifetime than blend-cast devices at higher film thicknesses.

Flexible Nanocomposite Conductors for Electromagnetic Interference Shielding

HIGHLIGHTS

Convincing candidates of flexible (stretchable/compressible) electromagnetic interference shielding nanocomposites are discussed in detail from the views of fabrication, mechanical elasticity and shielding performance. Detailed summary of the relationship between deformation of materials and electromagnetic shielding performance. The future directions and challenges in developing flexible (particularly elastic) shielding nanocomposites are highlighted. With the extensive use of electronic communication technology in integrated circuit systems and wearable devices, electromagnetic interference (EMI) has increased dramatically. The shortcomings of conventional rigid EMI shielding materials include high brittleness, poor comfort, and unsuitability for conforming and deformable applications. Hitherto, flexible (particularly elastic) nanocomposites have attracted enormous interest due to their excellent deformability. However, the current flexible shielding nanocomposites present low mechanical stability and resilience, relatively poor EMI shielding performance, and limited multifunctionality. Herein, the advances in low-dimensional EMI shielding nanomaterials-based elastomers are outlined and a selection of the most remarkable examples is discussed. And the corresponding modification strategies and deformability performance are summarized. Finally, expectations for this quickly increasing sector are discussed, as well as future challenges.

In Situ Silver Nanonets for Flexible Stretchable Electrodes

Shape-controlled synthesis is an effective method for controlling the physicochemical properties of nanomaterials, especially single-crystal nanomaterials, but it is difficult to control the morphology of single-crystal metallic nanomaterials. Silver nanowires (AgNWs) are regarded as key materials for the new generation of human-computer interaction, which can be applied in large-scale flexible and foldable devices, large-size touch screens, transparent LED films, photovoltaic cells, etc. When used on a large scale, the junction resistance will be generated at the overlap between AgNWs and the conductivity will decrease. When stretched, the overlap of AgNWs will be easily disconnected, which will lead to a decrease in electrical conductivity or even system failure. We propose that in situ silver nanonets (AgNNs) can solve the above two problems. The AgNNs exhibited excellent electrical conductivity (0.15 Ω∙sq^-1, which was 0.2 Ω∙sq^-1 lower than the 0.35 Ω∙sq^-1 square resistance of AgNWs) and extensibility (the theoretical tensile rate was 53%). In addition to applications in flexible stretchable sensing and display industries, they also have the potential to be used as plasmonic materials in molecular recognition, catalysis, biomedicine and other fields.

In situ performance and stability tests of large-area flexible polymer solar cells in the 35-km stratospheric environment

Flexible organic solar cells (FOSCs) are one of the most promising power sources for aerospace aircraft due to their attractive advantages with high power-per-weight ratio and excellent mechanical flexibility. Understanding the performance and stability of high-performance FOSCs is essential for the further development of FOSCs for aerospace applications. In this paper, after systematic investigations on the performance of the state-of-the-art high-performance solar cells under thermal cycle and intensive UV irradiation conditions, in situ performance and stability tests of the solar cells in the 35 km stratospheric environment were carried out through a high-altitude balloon uploading. The encapsulated FOSCs with an area of 0.64 cm² gave the highest power density of 15.26 mW/cm² and an efficiency over 11%, corresponding to a power-per-weight ratio of over 3.32 kW/kg. More importantly, the cells showed stable power output during the 3-h continuous flight at 35 km and only 10% performance decay after return to the lab, suggesting promising stability of the FOSCs in the stratospheric environment.

Chemically Welding Silver Nanowires toward Transferable and Flexible Transparent Electrodes in Heaters and Double-Sided Perovskite Solar Cells

Silver nanowires (AgNWs) are important materials for flexible transparent electrodes (FTEs). However, the loose stacking of nanowire junctions greatly affects the electric conductivity across adjacent nanowires. Soldering can effectively reduce the wire-wire contact resistance of AgNWs by epitaxially depositing nanosolders at the junctions, but the process normally needs to be performed with high energy consumption. In this work, we proposed a simple room-temperature method to achieve precise welding of junctions by adjusting the wettability of the soldered precursor solution on the surfaces of AgNWs. The nanoscale welding at nanowire cross junctions forms efficient conductive networks. Furthermore, reduced graphene oxide (rGO) was used to improve the stability of FTEs by wrapping the rGO around the AgNW surface. The obtained FTE shows a figure-of-merit (FoM) of up to 439.3 (6.5 Ω/sq at a transmittance of 88%) and has significant bending stability and environmental and acidic stability. A flexible transparent heater was successfully constructed, which could reach up to 160 °C within a short response time (43 s) and exhibit excellent switching stability. When laminating this FTE onto half perovskite solar cells as the top electrodes, the obtained double-side devices achieved power conversion efficiencies as high as 16.15% and 13.91% from each side, pointing out a convenient method for fabricating double-sided photovoltaic devices.

Solution-Processed Flexible Transparent Electrodes for Printable Electronics

Flexible transparent electrodes (FTEs) have been widely witnessed in various printable electronic devices, especially those involving light. So far, solution processes have demonstrated increasing advantages in preparing FTEs not only in their mild operation conditions and high-throughput but also in the diversity in micropatterning conductive nanomaterials into networks. For the FTEs, both high transparency and high conductivity are desirable, which therefore create requirements for the conductive network by considering the trade-off relationship between the coverage and the micropatterns of the network. In addition, the conductive networks also affect the flexibility of FTEs due to the deformation during bending/stretching. Consequently, solution processes capable of micropatterning conductive nanomaterials including nanoparticles, nanowires/polymers, and graphene/MXene play a crucial role in determining the performance of FTEs. Here, we reviewed recent research progress on solution-processed FTEs, including the solution processes, the solution-processable conductive nanomaterials and the substrates for making FTEs, and applications of FTEs in flexible electronics. Finally, we proposed several perspective outlooks of the FTEs, which aim at not only the enhanced performance but also the performances in extreme conditions and in integration. We believe that the review would offer inspiration for developing functional FTEs.

Surface-Energy-Mediated Interfacial Adhesion for Mechanically Robust Ultraflexible Organic Photovoltaics

Insufficient interfacial adhesion is a widespread problem across multilayered devices that undermines their reliability. In flexible organic photovoltaics (OPVs), poor interfacial adhesion can accelerate degradation and failure under mechanical deformations due to the intrinsic brittleness and mismatching mechanical properties between functional layers. We introduce an argon plasma treatment for OPV devices, which yields 58% strengthening in interfacial adhesion between an active layer and a MoO_X hole transport layer, thus contributing to mechanical reliability. The improved adhesion is attributed to the increased surface energy of the active layer that occurred after the mild argon plasma treatment. The mechanically stabilized interface retards the flexible device degradation induced by mechanical stress and maintains a power conversion efficiency of 94.8% after 10,000 cycles of bending with a radius of 2.5 mm. In addition, a fabricated 3 μm thick ultraflexible OPV device shows excellent mechanical robustness, retaining 91.0% of the initial efficiency after 1000 compressing-stretching cycles with a 40% compression ratio. The developed ultraflexible OPV devices can operate stably at the maximum power point under continuous 1 sun illumination for 500 min with an 89.3% efficiency retention. Overall, we validate a simple interfacial linking strategy for efficient and mechanically robust flexible and ultraflexible OPVs.

Double Asymmetric Core Optimizes Crystal Packing to Enable Selenophene-based Acceptor with Over 18 % Efficiency in Binary Organic Solar Cells

Side-chain tailoring is a promising method to optimize the performance of organic solar cells (OSCs). However, asymmetric alkyl chain-based small molecular acceptors (SMAs) are still difficult to afford. Herein, we adopted a novel asymmetric n-nonyl/undecyl substitution strategy and synthesized two A-D₁ A'D₂ -A double asymmetric isomeric SMAs with asymmetric selenophene-based central core for OSCs. Crystallographic analysis indicates that AYT9Se11-Cl forms a more compact and order intermolecular packing compared to AYT11Se9-Cl, which contributed to higher electron mobility in neat AYT9Se11-Cl film. Moreover, the PM6 : AYT9Se11-Cl blend film shows a better morphology with appropriate phase separation and distinct face-on orientation than PM6 : AYT11Se9-Cl. The OSCs with PM6 : AYT9Se11-Cl obtain a superior PCE of 18.12 % compared to PM6 : AYT11Se9-Cl (17.52 %), which is the best efficiency for the selenium-incorporated SMAs in binary BHJ OSCs. Our findings elucidate that the promising double asymmetric strategy with isomeric alkyl chains precisely modulates the crystal packing and enhances the photovoltaic efficiency of selenophene-incorporated SMAs.

Versatile Applications of Silver Nanowire-Based Electrodes and Their Impacts

Indium tin oxide (ITO) is currently the most widely used material for transparent electrodes; however, it has several drawbacks, including high cost, brittleness, and environmental concerns. Silver nanowires (AgNWs) are promising alternatives to ITO as materials for transparent electrodes owing to their high electrical conductivity, transparency in the visible range of wavelengths, and flexibility. AgNWs are effective for various electronic device applications, such as touch panels, biosensors, and solar cells. However, the high synthesis cost of AgNWs and their poor stability to external chemical and mechanical damages are significant challenges that need to be addressed. In this review paper, we discuss the current state of research on AgNW transparent electrodes, including their synthesis, properties, and potential applications.

Direct Writing of Silver Nanowire Patterns with Line Width down to 50 μm and Ultrahigh Conductivity

Direct writing of one-dimensional nanomaterials with large aspect ratios into customized, highly conductive, and high-resolution patterns is a challenging task. In this work, thin silver nanowires (AgNWs) with a length-to-diameter ratio of 730 are employed as a representative example to demonstrate a potent direct ink writing (DIW) strategy, in which aqueous inks using a natural polymer, sodium alginate, as the thickening agent can be easily patterned with arbitrary geometries and controllable structural features on a variety of planar substrates. With the aid of a quick spray-and-dry postprinting treatment at room temperature, the electrical conductivity and substrate adhesion of the written AgNWs-patterns improve simultaneously. This simple, environment benign, and low-temperature DIW strategy is effective for depositing AgNWs into patterns that are high-resolution (with line width down to 50 μm), highly conductive (up to 1.26 × 105 S/cm), and mechanically robust and have a large alignment order of NWs, regardless of the substrate's hardness, smoothness, and hydrophilicity. Soft electroadhesion grippers utilizing as-manufactured interdigitated AgNWs-electrodes exhibit an increased shear adhesion force of up to 15.5 kPa at a driving voltage of 3 kV, indicating the strategy is very promising for the decentralized and customized manufacturing of soft electrodes for future soft electronics and robotics.

The charge-transfer states and excitation energy transfers of halogen-free organic molecules from first-principles many-body Green's function theory

The organic solar cells based on halogen-free components, have been the new favorites to develop green and renewable energy. PBDB-T and its derivatives are considered the superior electron donors to construct the solar cells. Although there are plenty of researches about them, the charge-transfer mechanisms and excitation energy transfers of relative organic solar cells are still unclear, the developments of photovoltaic devices are restricted consequently. In this work, we calculate the electronic structures and excited-state properties of PBDB-T, PBT1-C, PBT1-O and PBT1-S donors in the gas phase from the many-body Green's function theory. With BTP-IC and BTP-IS as the acceptors, we consider the Förster, Dexter, and overlap electronic couplings to compute the excitation energy transfers of the dimers. The ionization energies and excited-state energies of the four donors calculated by GW + BSE are in good agreement with experiments, and they are sensitive to the functionals in the computation. We find two charge transfer schemes. The thienyl of PBDB-T molecule makes its charge-transfer state at the lowest energy, and the total electronic coupling of PBDB-T based dimer is the strongest. The Dexter, and overlap types electronic couplings are significant to study the excitation energy transfer of organic heterojunctions. We provide a theoretical guide in the design and synthesis of higher-performance halogen-free donors.

Mechanically Stable Flexible Organic Photovoltaics with Silver Nanomesh for Indoor Applications

Enhanced device performance of flexible organic solar cells (FOSCs) was achieved according to the development of organic solar cells (OSCs). OSCs are promising candidates as energy sources for low-power supply systems such as the Internet of Things (IoT) under indoor lighting environments. To apply FOSCs to flexible or wearable applications, they must be mechanically stable. In this study, we fabricated FOSCs with silver nanomesh (AgNM) as the bottom transparent conductive electrode (TCE). Instead of indium tin oxide (ITO), AgNMs were prepared using three pitches of 25, 50, and 100 μm with a square pattern, using a poly(ethylene terephthalate) (PET) substrate. Notably, the device using AgNMs with a pitch of 25 μm exhibited a power conversion efficiency (PCE) of 14.93% under 1 sun illumination and 17.91% under 1000 lux of light-emitting diode (LED) light conditions. Flexible devices using AgNMs maintained over 92% of their initial PCE under 1 sun illumination (PCE decreased to 12.98 from 14.04%) and over 92% when tested under 1000 lux of LED light illumination (PCE decreased to 16.57 from 17.91%) after 1000 instances of bending. These results demonstrate the advantages of using AgNMs as an alternative TCE under both 1 sun and indoor lightning environments and are promising candidates for flexible applications.

Self-assembly, alignment, and patterning of metal nanowires

Armed with the merits of one-dimensional nanostructures (flexibility, high aspect ratio, and anisotropy) and metals (high conductivity, plasmonic properties, and catalytic activity), metal nanowires (MNWs) have stood out as a new class of nanomaterials in the last two decades. They are envisaged to expedite significantly and even revolutionize a broad spectrum of applications related to display, sensing, energy, plasmonics, photonics, and catalysis. Compared with disordered MNWs, well-organized MNWs would not only enhance the intrinsic physical and chemical properties, but also create new functions and sophisticated architectures of optoelectronic devices. This paper presents a comprehensive review of assembly strategies of MNWs, including self-assembly for specific structures, alignment for anisotropic constructions, and patterning for precise configurations. The technical processes, underlying mechanisms, performance indicators, and representative applications of these strategies are described and discussed to inspire further innovation in assembly techniques and guide the fabrication of optoelectrical devices. Finally, a perspective on the critical challenges and future opportunities of MNW assembly is provided.

Sequential Processing Enables 17% All-Polymer Solar Cells via Non-Halogen Organic Solvent

All-polymer solar cells (All-PSCs), whose electron donor and acceptors are both polymeric materials, have attracted great research attention in the past few years. However, most all-PSC devices with top-of-the-line efficiencies are processed from chloroform. In this work, we apply the sequential processing (SqP) method to fabricate All-PSCs from an aromatic hydrocarbon solvent, toluene, and obtain efficiencies up to 17.0%. By conducting a series of characterizations on our films and devices, we demonstrate that the preparation of SqP devices using toluene can effectively reduce carrier recombination, enhance carrier mobility and promote the fill factor of the device.

Uniform Silver Nanowire Patterned Electrode on Robust PEN Substrate Using Poly(2-hydroxyethyl methacrylate) Underlayer

Silver nanowire (AgNW) electrodes are among the most essential flexible transparent electrodes (FTEs) emerging as promising alternatives to brittle indium tin oxide (ITO) electrodes. The polymer comprising the plastic substrate to which the AgNWs are applied must also satisfy the mechanical requirements of the final device and withstand the device processing conditions. However, AgNW-based FTEs have some limitations, such as poor adhesion to coated plastic substrates, surface roughness, and difficulty in patterning. This study demonstrates a new strategy for creating AgNW-based patterned flexible poly(ethylene 2,6-naphthalate) (PEN)-based electrodes with appreciable optical and electrical properties. Introducing poly(2-hydroxyethyl methacrylate) on the PEN substrate enhanced the adhesion between the substrate and AgNWs and improved the dispersibility of the AgNWs. Poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) and a small amount of 2,4-hexadiyne-1,6-diol as a photosensitizer were coated onto the AgNW layer to improve the surface roughness and achieve an effective electrode pattern. By varying the AgNW concentration, we could tune the density and thickness of the AgNWs to optimize the sheet resistance and transmittance. Optimized AgNWs with a sheet resistance of 22.6 Ω/□ and transmittance of 92.3% at 550 nm were achieved. A polymer solar cell (PSC) was fabricated to evaluate the characteristics of the device employing the flexible electrodes. This PSC showed not only a high power conversion efficiency of 11.20%, similar to that of ITO-based devices, but also excellent mechanical stability, which is difficult to achieve in ITO-based flexible devices.

Mechanically and Ultraviolet Light Stable Ultrathin Organic Solar Cell via Semi-Embedding Silver Nanowires in a Hydrogen Bonds-Based Polyimide

Ultrathin organic solar cells (OSCs) with both high power conversion efficiency (PCE) and operational stability are of great significance for the industrial applications but still challenging. Here, we synthesized a polyimide (PI) substrate for high-performance and stable ultrathin OSCs, which was physically crosslinked via strong hydrogen bonds (denoted as HB-PI) to enhance the mechanical, thermal, solvent-resistant, and UV filtering properties (with a cut-off wavelength of 376 nm). An ultrathin flexible transparent composite electrode (FTCE, ∼7 μm) was fabricated via semi-embedding AgNWs in the HB-PI substrate. The FTCE possesses excellent optoelectronic property, smooth surface, and high mechanical stability simultaneously. Based on this FTCE, an ultrathin OSC was constructed with a PCE of 13.52% (average of 13.22%). Moreover, the ultrathin OSC showed outstanding mechanical stability (PCE decreased by less than 4% after 1000 bending cycles at a small bending radius of 0.5 mm) and superior UV light stability (no evident PCE degradation after irradiation under UV light for 10 h). This work will provide a new avenue for fabricating high-performance and stable ultrathin OSCs. This article is protected by copyright. All rights reserved.

Low-Dimensional Nanomaterial Systems Formed by IVA Group Elements Allow Energy Conversion Materials to Flourish

In response to the exhaustion of traditional energy, green and efficient energy conversion has attracted growing attention. The IVA group elements, especially carbon, are widely distributed and stable in the earth’s crust, and have received a lot of attention from scientists. The low-dimensional structures composed of IVA group elements have special energy band structure and electrical properties, which allow them to show more excellent performance in the fields of energy conversion. In recent years, the diversification of synthesis and optimization of properties of IVA group elements low-dimensional nanomaterials (IVA-LD) contributed to the flourishing development of related fields. This paper reviews the properties and synthesis methods of IVA-LD for energy conversion devices, as well as their current applications in major fields such as ion battery, moisture electricity generation, and solar-driven evaporation. Finally, the prospects and challenges faced by the IVA-LD in the field of energy conversion are discussed.