Enhanced Thermal Conductivity of Epoxy Composites Filled with 2D Transition Metal Carbides (MXenes) with Ultralow Loading

SPI-Modified h-BN Nanosheets-Based Thermal Interface Materials for Thermal Management Applications

The rising concern over the usage of electronic devices and the operating environment requires efficient thermal interface materials (TIMs) to take away the excess heat generated from hotspots. TIMs are crucial in dissipating undesired heat by transferring energy from the source to the heat sink. Silicone oil (SO)-based composites are the most used TIMs due to their strong bonding and oxidation resistance. However, thermal grease performance is unreliable due to aging effects, toxic chemicals, and a higher percentage of fillers. In this work, TIMs are prepared using exfoliated hexagonal boron nitride nanosheets (h-BNNS) as a nanofiller, and they were functionalized by ecofriendly natural biopolymer soy protein isolate (SPI). The exfoliated h-BNNS has an average lateral size of ∼266 nm. The functionalized h-BNNS/SPI are used as fillers in the SO matrix, and composites are prepared using solution mixing. Hydrogen bonding is present between the organic chain/oxygen in silicone polymer, and the functionalized h-BNNS are evident from the FTIR measurements. The thermal conductivity of h-BNNS/SPI/SO was measured using the modified transient plane source (MTPS) method. At room temperature, the maximum thermal conductivity is 1.162 Wm-1K-1 (833% enhancement) at 50 wt % of 3:1 ratio of h-BNNS:SPI, and the thermal resistance (TR) of the composite is 5.249 × 106 K/W which is calculated using the Foygel nonlinear model. The heat management application was demonstrated by applying TIM on a 10 W LED bulb. It was found that during heating, the 50 wt % TIM decreases the surface temperature of LED by ∼6 °C compared with the pure SO-based TIM after 10 min of ON condition. During cooling, the modified TIM reduces the surface temperature by ∼8 °C under OFF conditions within 1 min. The results indicate that natural polymers can effectively stabilize and link layered materials, enhancing the efficiency of TIMs for cooling electronics and LEDs.

2D Materials-Based Thermal Interface Materials: Structure, Properties, and Applications

The challenges associated with heat dissipation in high-power electronic devices used in communication, new energy, and aerospace equipment have spurred an urgent need for high-performance thermal interface materials (TIMs) to establish efficient heat transfer pathways from the heater (chip) to heat sinks. Recently, emerging 2D materials, such as graphene and boron nitride, renowned for their ultrahigh basal-plane thermal conductivity and the capacity to facilitate cross-scale, multi-morphic structural design, have found widespread use as thermal fillers in the production of high-performance TIMs. To deepen the understanding of 2D material-based TIMs, this review focuses primarily on graphene and boron nitride-based TIMs, exploring their structures, properties, and applications. Building on this foundation, the developmental history of these TIMs is emphasized and a detailed analysis of critical challenges and potential solutions is provided. Additionally, the preparation and application of some other novel 2D materials-based TIMs are briefly introduced, aiming to offer constructive guidance for the future development of high-performance TIMs.

Multi-Interface Engineering of MXenes for Self-Powered Wearable Devices

Self-powered wearable devices with integrated energy supply module and sensitive sensors have significantly blossomed for continuous monitoring of human activity and the surrounding environment in healthcare sectors. The emerging of MXene-based materials has brought research upsurge in the fields of energy and electronics, owing to their excellent electrochemical performance, large surface area, superior mechanical performance, and tunable interfacial properties, where their performance can be further boosted via multi-interface engineering. Herein, a comprehensive review of recent progress in MXenes for self-powered wearable devices is discussed from the aspects of multi-interface engineering. The fundamental properties of MXenes including electronic, mechanical, optical, and thermal characteristics are discussed in detail. Different from previous review works on MXenes, multi-interface engineering of MXenes from termination regulation to surface modification and their impact on the performance of materials and energy storage/conversion devices are summarized. Based on the interfacial manipulation strategies, potential applications of MXene-based self-powered wearable devices are outlined. Finally, proposals and perspectives are provided on the current challenges and future directions in MXene-based self-powered wearable devices.

In Situ Growth of Interfacially Nanoengineered 2D-2D WS2/Ti3C2Tx MXene for the Enhanced Performance of Hydrogen Evolution Reactions

In line with current research goals involving water splitting for hydrogen production, this work aims to develop a noble-metal-free electrocatalyst for a superior hydrogen evolution reaction (HER). A single-step interfacial activation of Ti3C2Tx MXene layers was employed by uniformly growing embedded WS2 two-dimensional (2D) nanopetal-like sheets through a facile solvothermal method. We exploited the interactions between WS2 nanopetals and Ti3C2Tx nanolayers to enhance HER performance. A much safer method was adopted to synthesize the base material, Ti3C2Tx MXene, by etching its MAX phase through mild in situ HF formation. Consequently, WS2 nanopetals were grown between the MXene layers and on edges in a one-step solvothermal method, resulting in a 2D-2D nanocomposite with enhanced interactions between WS2 and Ti3C2Tx MXene. The resulting 2D-2D nanocomposite was thoroughly characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman, Fourier transform infrared (FTIR), and X-ray photoelectron spectroscopy (XPS) analyses before being utilized as working electrodes for HER application. Among various loadings of WS2 into MXene, the 5% WS2-Ti3C2Tx MXene sample exhibited the best activity toward HER, with a low overpotential value of 66.0 mV at a current density of -10 mA cm-2 in a 1 M KOH electrolyte and a remarkable Tafel slope of 46.7 mV·dec-1. The intercalation of 2D WS2 nanopetals enhances active sites for hydrogen adsorption, promotes charge transfer, and helps attain an electrochemical stability of 50 h, boosting HER reduction potential. Furthermore, theoretical calculations confirmed that 2D-2D interactions between 1T/2H-WS2 and Ti3C2Tx MXene realign the active centers for HER, thereby reducing the overpotential barrier.

High-Performance, Multifunctional, and Designable Carbon Fiber Felt Skeleton Epoxy Resin Composites EP/CF-(CNT/AgBNs)x for Thermal Conductivity and Electromagnetic Interference Shielding

In this work, high-performance epoxy resin (EP) composites with simultaneous excellent thermal conductivity (TC) and outstanding electromagnetic shielding properties are fabricated through the structural synergy of 1D carbon nanotubes and 2D silver-modified boron nitride nanoplates (CNT/AgBNs) to erect microscopic 3D networks on long-range carbon fiber (CF) felt skeletons. The line-plane combination of CNT/AgBNs improve the interfacical bonding involving EP and CF felts and alleviate the phonon scattering at the interface. Eventually, the TC of the EP composites is enhanced by 333% (up to 0.91 W m-1 K-1 ) with respect to EP due to the efficient and orderly transmission of phonons along the 3D pathway. Meanwhile, the unique anisotropic structure of CF felt and exceptional insulating BNs diminishes the electronic conduction between CNT and CFs, which protects the through-plane insulating properties of EP composites. Furthermore, the EP composites present favorable electromagnetic shielding properties (51.36 dB) attributed to the multiple reflection and adsorption promoted by the multiple interfaces of stacked AgBNs and heterointerface among CNT/AgBNs, CF felt and EP. Given these distinguishing features, the high-performance EP composites open a convenient avenue for electromagnetic wave (EMW) shielding and thermal management applications.

Controllable interface-tailored strategy to reduce the nanotribological properties of Ti3C2Txby depositing MoS2using atomic layer deposition

Ti3C2TxMXene has attracted widespread attention in lubrication owing to its unique structure and surface properties. However, the inferior nanotribological properties of Ti3C2Txstill limit its applications in nano lubricants. Herein, we propose a controllable interface-tailored strategy to reduce the nanotribological properties of Ti3C2Txby depositing MoS2nano-sheet on its surface using atomic layer deposition (ALD). The nanotribological properties of the MoS2/Ti3C2Txnanocomposites synthesized by ALD are studied by atomic force microscope for the first time. At the optimal 20 ALD MoS2cycles, the nanofriction of MoS2/Ti3C2Txhas been reduced by 57%, 46%, and 44% (at 5, 10, and 15 nN load, respectively), while the adhesion has been reduced by 59%, compared to the original Ti3C2Tx. The results can contribute to understanding of the nanotribological mechanisms of Ti3C2Txcomposites and provide the potential prospects for Ti3C2Txas a nanoscale adjustable lubricant.

Electrically insulating PBO/MXene film with superior thermal conductivity, mechanical properties, thermal stability, and flame retardancy

Constructing flexible and robust thermally conductive but electrically insulating composite films for efficient and safe thermal management has always been a sought-after research topic. Herein, a nacre-inspired high-performance poly(p-phenylene-2,6-benzobisoxazole) (PBO)/MXene nanocomposite film was prepared by a sol-gel-film conversion method with a homogeneous gelation process. Because of the as-formed optimized brick and mortar structure, and the strong bridging and caging effects of the fine PBO nanofibre network on the MXene nanosheets, the resulting nanocomposite film is electrically insulating (2.5 × 109 Ω cm), and exhibits excellent mechanical properties (tensile strength of 416.7 MPa, Young's modulus of 9.1 GPa and toughness of 97.3 MJ m-3). More importantly, the synergistic orientation of PBO nanofibres and MXene nanosheets endows the film with an in-plane thermal conductivity of 42.2 W m-1 K-1. The film also exhibits excellent thermal stability and flame retardancy. This work broadens the ideas for preparing high-performance thermally conductive but electrically insulating composites.

Few Layer Ti3C2 MXene-Based Label-Free Aptasensor for Ultrasensitive Determination of Chloramphenicol in Milk

Quantitative detection of veterinary drug residues in animal-derived food is of great significance. In this work, a simple and label-free electrochemical aptasensor for the highly sensitive detection of chloramphenicol (CAP) in milk was successfully developed based on a new biosensing method, where the single- or few-layer Ti3C2 MXene nanosheets functionalized via the specific aptamer by self-assembly were used as electrode modifiers for a glassy carbon electrode (aptamer/Ti3C2 MXene/GCE). Differential pulse voltammetry (DPV), electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), scanning electron microscopy (SEM), atomic force microscope (AFM), and so on were utilized for electrochemical and morphological characterization. Under the optimized conditions, the constructed aptasensor exhibited excellent performance with a wider linearity to CAP in the range from 10 fM to 1 μM and a low detection limit of 1 fM. Aptamer/Ti3C2 MXene/GCE demonstrated remarkable selectivity over other potentially interfering antibiotics, as well as exceptional reproducibility and stability. In addition, the aptasensor was successfully applied to determine CAP in milk with acceptable recovery values of 96.13% to 108.15% and relative standard deviations below 9%. Therefore, the proposed electrochemical aptasensor is an excellent alternative for determining CAP in food samples.

Universal Capacitance Boost-Smart Surface Nanoengineering by Zwitterionic Molecules for 2D MXene Supercapacitor

Two-dimensional nanomaterials, as one of the most widely used substrates for energy storage devices, have achieved great success in terms of the overall capacity. Despite the extensive research effort dedicated to this field, there are still major challenges concerning capacitance modulation and stability of the 2D materials that need to be overcome. Doping of the crystal structures, pillaring methods and 3D structuring of electrodes have been proposed to improve the material properties. However, these strategies are usually accompanied by a significant increase in the cost of the entire material preparation process and also a lack of the versatility for modification of the various types of the chemical structures. Hence in this work, versatile, cheap, and environmentally friendly method for the enhancement of the electrochemical parameter of various MXene-based supercapacitors (Ti3 C2 , Nb2 C, and V2 C), coated with functional and charged organic molecules (zwitterions-ZW) is introduced. The MXene-organic hybrid strategy significantly increases the ionic absorption (capacitance boost) and also forms a passivation layer on the oxidation-prone surface of the MXene through the covalent bonds. Therefore, this work demonstrates a new, cost-effective, and versatile approach (MXene-organic hybrid strategy) for the design and fabrication of hybrid MXene-base electrode materials for energy storage/conversion systems.

Effective Surface Modification of 2D MXene toward Thermal Energy Conversion and Management

Thermal energy management is a crucial aspect of many research developments, such as hybrid and soft electronics, aerospace, and electric vehicles. The selection of materials is of critical importance in these applications to manage thermal energy effectively. From this perspective, MXene, a new type of 2D material, has attracted considerable attention in thermal energy management, including thermal conduction and conversion, owing to its unique electrical and thermal properties. However, tailored surface modification of 2D MXenes is required to meet the application requirements or overcome specific limitations. Herein, a comprehensive review of surface modification of 2D MXenes for thermal energy management is discussed. First, this work discusses the current progress in the surface modification of 2D MXenes, including termination with functional groups, small-molecule organic compound functionalization, and polymer modification and composites. Subsequently, an in situ analysis of surface-modified 2D MXenes is presented. This is followed by an overview of the recent progress in the thermal energy management of 2D MXenes and their composites, such as Joule heating, heat dissipation, thermoelectric energy conversion, and photothermal conversion. Finally, some challenges facing the application of 2D MXenes are discussed, and an outlook on surface-modified 2D MXenes is provided.

Emergence of MXene and MXene-Polymer Hybrid Membranes as Future- Environmental Remediation Strategies

The continuous deterioration of the environment due to extensive industrialization and urbanization has raised the requirement to devise high-performance environmental remediation technologies. Membrane technologies, primarily based on conventional polymers, are the most commercialized air, water, solid, and radiation-based environmental remediation strategies. Low stability at high temperatures, swelling in organic contaminants, and poor selectivity are the fundamental issues associated with polymeric membranes restricting their scalable viability. Polymer-metal-carbides and nitrides (MXenes) hybrid membranes possess remarkable physicochemical attributes, including strong mechanical endurance, high mechanical flexibility, superior adsorptive behavior, and selective permeability, due to multi-interactions between polymers and MXene's surface functionalities. This review articulates the state-of-the-art MXene-polymer hybrid membranes, emphasizing its fabrication routes, enhanced physicochemical properties, and improved adsorptive behavior. It comprehensively summarizes the utilization of MXene-polymer hybrid membranes for environmental remediation applications, including water purification, desalination, ion-separation, gas separation and detection, containment adsorption, and electromagnetic and nuclear radiation shielding. Furthermore, the review highlights the associated bottlenecks of MXene-Polymer hybrid-membranes and its possible alternate solutions to meet industrial requirements. Discussed are opportunities and prospects related to MXene-polymer membrane to devise intelligent and next-generation environmental remediation strategies with the integration of modern age technologies of internet-of-things, artificial intelligence, machine-learning, 5G-communication and cloud-computing are elucidated.

Recent Studies on Thermally Conductive 3D Aerogels/Foams with the Segregated Nanofiller Framework

As technology advances toward ongoing circuit miniaturization and device size reduction followed by improved power density, heat dissipation is becoming a key challenge for electronic equipment. Heat accumulation can be prevented if the heat from electrical equipment is efficiently exported, ensuring a device's lifespan and dependability and preventing otherwise possible mishaps or even explosions. Hence, thermal management applications, which include altering the role of aerogels from thermally insulative to thermally conductive, have recently been a hot topic for 3D-aerogel-based thermal interface materials. To completely comprehend three-dimensional (3D) networks, we categorized and comparatively analyzed aerogels based on carbon nanomaterials, namely fibers, nanotubes, graphene, and graphene oxide, which have capabilities that may be fused with boron nitride and impregnated for better thermal performance and mechanical stability by polymers, including epoxy, cellulose, and polydimethylsiloxane (PDMS). An alternative route is presented in the comparative analysis by carbonized cellulose. As a result, the development of structurally robust and stiff thermally conductive aerogels for electronic packaging has been predicted to increase polymer thermal management capabilities. The latest trends include the self-organization of an anisotropic structure on several hierarchical levels within a 3D framework. In this study, we highlight and analyze the recent advances in 3D-structured thermally conductive aerogels, their potential impact on the next generation of electronic components based on advanced nanocomposites, and their future prospects.

Three-dimensional hierarchically porous MoS2 foam as high-rate and stable lithium-ion battery anode

Architected materials that actively respond to external stimuli hold tantalizing prospects for applications in energy storage, wearable electronics, and bioengineering. Molybdenum disulfide, an excellent two-dimensional building block, is a promising candidate for lithium-ion battery anode. However, the stacked and brittle two-dimensional layered structure limits its rate capability and electrochemical stability. Here we report the dewetting-induced manufacturing of two-dimensional molybdenum disulfide nanosheets into a three-dimensional foam with a structural hierarchy across seven orders of magnitude. Our molybdenum disulfide foam provides an interpenetrating network for efficient charge transport, rapid ion diffusion, and mechanically resilient and chemically stable support for electrochemical reactions. These features induce a pseudocapacitive energy storage mechanism involving molybdenum redox reactions, confirmed by in-situ X-ray absorption near edge structure. The extraordinary electrochemical performance of molybdenum disulfide foam outperforms most reported molybdenum disulfide-based Lithium-ion battery anodes and state-of-the-art materials. This work opens promising inroads for various applications where special properties arise from hierarchical architecture.

3D Printing of Ultrathin MXene toward Tough and Thermally Resistant Nanocomposites

Liquid crystal display (LCD)-based 3D printing, a facile and cost-effective manufacturing technique, is often applied when fabricating objects with porcelain structures using photosensitive resins (PSRs). Currently, 3D printed constructions are typically used as models for demonstration purposes rather than industrial applications because of their poor performance. In this study, we prepared nanocomposites by incorporating Ti₃C₂ MXene nanosheets to enhance the overall characteristics of a PSR, including mechanical properties and thermal resistance. Notably, the designed nanocomposites showed optimum performance at an MXene loading of 0.5% w/w. The mechanical properties of the designed nanocomposites confirmed the enhanced ultimate tensile and flexural strengths (by 32.1% and 42.7%, respectively), at 0.5% w/w MXene loading. Moreover, the incorporated MXene presented no substantial influence on the toughness of the PSR. The glass transition and thermal degradation temperatures at 5% weight loss increased by 7.4 and 10.6 °C, respectively, resulting predominantly from the hydrogen bonding between the PSR and MXene. Together, the experimental results indicate that the designed PSR/MXene nanocomposites are expected to replace pristine resins for LCD printing in various practical applications.

A highly orientational architecture formed by covalently bonded graphene to achieve high through-plane thermal conductivity of polymer composites

Combining the advantages of high thermal conductivities and low graphene contents to fabricate polymer composites for applications in thermal management is still a great challenge due to the high defect degree of exfoliated graphene, the poor orientation of graphene in polymer matrices, and the horrible phonon scattering between graphene/graphene and graphene/polymer interfaces. Herein, mesoplasma chemical vapor deposition (CVD) technology was successfully employed to synthesize vertically aligned graphene nanowalls (GNWs), which are covalently bonded by high-quality CVD graphene nanosheets. The unique architecture leads to an excellent thermal enhancement capacity of the GNWs, and a corresponding composite film with a matrix of polyvinylidene fluoride (PVDF) presented a high through-plane thermal conductivity of 12.8 ± 0.77 W m^-1 K^-1 at a low filler content of 4.0 wt%, resulting in a thermal conductivity enhancement per 1 wt% graphene loading of 1659, which is far superior to that using conventional graphene structures as thermally conductive pathways. In addition, this composite exhibited an excellent capability in cooling a high-power light-emitting diode (LED) device under real application conditions. Our finding provides a new route to prepare high-performance thermal management materials with low filler loadings via the rational design of the microstructures/interfaces of graphene skeletons.

An Efficient Method to Determine the Thermal Behavior of Composite Material with Loading High Thermal Conductivity Fillers

Improvement of the thermal conductivity of encapsulant material using doping filler is an important requirement for electronic device packaging. We proposed a simple method for determining the thermal characteristics of composite material that can help save time, increase research performance, and reduce the cost of buying testing equipment. Based on the theory of Fourier law, a general 3D model is simplified into a 2D model, which can then be applied to calculate the thermal conductivity of the tested sample. The temperature distribution inside the sample is simulated by the finite element method using MATLAB software; this is a simple and useful option for researchers who conduct studies on thermal conduction. In addition, an experimental setup is proposed to help determine the extent of thermal conductivity improvement in a sample with doping filler compared to a bare sample. This method is helpful for research on optoelectronics packaging, which relates to the enhancement of thermal conductivity composite material.

Curing and Molecular Dynamics Simulation of MXene/Phenolic Epoxy Composites with Different Amine Curing Agent Systems

Herein, the curing kinetics and the glass transition temperature (T_g) of MXene/phenolic epoxy composites with two curing agents, i.e., 4,4-diaminodiphenyl sulfone (DDS) and dicyandiamine (DICY), are systematically investigated using experimental characterization, mathematical modeling and molecular dynamics simulations. The effect of MXene content on an epoxy resin/amine curing agent system is also studied. These results reveal that the MXene/epoxy composites with both curing agent systems conform to the SB(m,n) two-parameter autocatalytic model. The addition of MXene accelerated the curing of the epoxy composite and increased the T_g by about 20 K. In addition, molecular dynamics were used to simulate the T_g of the cross-linked MXene/epoxy composites and to analyze microstructural features such as the free volume fraction (FFV). The simulation results show that the introduction of MXene improves the T_g and FFV of the simulated system. This is because the introduction of MXene restricts the movement of the epoxy/curing agent system. The conclusions are in good agreement with the experimental results.

Recent Advances in MXene/Epoxy Composites: Trends and Prospects

Epoxy resins are thermosets with interesting physicochemical properties for numerous engineering applications, and considerable efforts have been made to improve their performance by adding nanofillers to their formulations. MXenes are one of the most promising functional materials to use as nanofillers. They have attracted great interest due to their high electrical and thermal conductivity, hydrophilicity, high specific surface area and aspect ratio, and chemically active surface, compatible with a wide range of polymers. The use of MXenes as nanofillers in epoxy resins is incipient; nevertheless, the literature indicates a growing interest due to their good chemical compatibility and outstanding properties as composites, which widen the potential applications of epoxy resins. In this review, we report an overview of the recent progress in the development of MXene/epoxy nanocomposites and the contribution of nanofillers to the enhancement of properties. Particularly, their application for protective coatings (i.e., anticorrosive and friction and wear), electromagnetic-interference shielding, and composites is discussed. Finally, a discussion of the challenges in this topic is presented.

Characterization of phonon thermal transport of Ti3C2TxMXene thin film

Two-dimensional MXene materials with high electrotonic conductivity, good chemical stability, and unique laminar structure show great potential in the field of electrochemistry. In contrast to the widely concerned electrical properties, studies on the thermal properties of MXene materials are very limited. This paper presents a comprehensive analysis of the thermal properties of Ti₃C₂T_xMXene thin film. Thermal diffusivity and thermal conductivity of Ti₃C₂T_xfilms are characterized by the transient electro-thermal technique. The experimental results show a 16% enhancement in thermal conductivity when the temperature is increased from 307 K to 352 K. The phonon transport contributes substantially to thermal conductivity compared with electron transport. Molecular dynamic simulation is employed to further investigate the role of phonon thermal transport of Ti₃C₂layer. It is found that the combined effect of specific heat capacity, stacking structure and internal stress states is responsible for the thermal transport performance of Ti₃C₂T_xMXene thin film.

High-Efficiency Electromagnetic Interference Shielding of rGO@FeNi/Epoxy Composites with Regular Honeycomb Structures

With the rapid development of fifth-generation mobile communication technology and wearable electronic devices, electromagnetic interference and radiation pollution caused by electromagnetic waves have attracted worldwide attention. Therefore, the design and development of highly efficient EMI shielding materials are of great importance. In this work, the three-dimensional graphene oxide (GO) with regular honeycomb structure (GH) is firstly constructed by sacrificial template and freeze-drying methods. Then, the amino functionalized FeNi alloy particles (f-FeNi) are loaded on the GH skeleton followed by in-situ reduction to prepare rGH@FeNi aerogel. Finally, the rGH@FeNi/epoxy EMI shielding composites with regular honeycomb structure is obtained by vacuum-assisted impregnation of epoxy resin. Benefitting from the construction of regular honeycomb structure and electromagnetic synergistic effect, the rGH@FeNi/epoxy composites with a low rGH@FeNi mass fraction of 2.1 wt% (rGH and f-FeNi are 1.2 and 0.9 wt%, respectively) exhibit a high EMI shielding effectiveness (EMI SE) of 46 dB, which is 5.8 times of that (8 dB) for rGO/FeNi/epoxy composites with the same rGO/FeNi mass fraction. At the same time, the rGH@FeNi/epoxy composites also possess excellent thermal stability (heat-resistance index and temperature at the maximum decomposition rate are 179.1 and 389.0 °C respectively) and mechanical properties (storage modulus is 8296.2 MPa).

A Double-Deck Structure of Reduced Graphene Oxide Modified Porous Ti3C2Tx Electrode towards Ultrasensitive and Simultaneous Detection of Dopamine and Uric Acid

Considering the vital physiological functions of dopamine (DA) and uric acid (UA) and their coexistence in the biological matrix, the development of biosensing techniques for their simultaneous and sensitive detection is highly desirable for diagnostic and analytical applications. Therefore, Ti₃C₂T_x/rGO heterostructure with a double-deck layer was fabricated through electrochemical reduction. The rGO was modified on a porous Ti₃C₂T_x electrode as the biosensor for the detection of DA and UA simultaneously. Debye length was regulated by the alteration of rGO mass on the surface of the Ti₃C₂T_x electrode. Debye length decreased with respect to the rGO electrode modified with further rGO mass, indicating that fewer DA molecules were capable of surpassing the equilibrium double layer and reaching the surface of rGO to achieve the voltammetric response of DA. Thus, the proposed Ti₃C₂T_x/rGO sensor presented an excellent performance in detecting DA and UA with a wide linear range of 0.1-100 μM and 1-1000 μM and a low detection limit of 9.5 nM and 0.3 μM, respectively. Additionally, the proposed Ti₃C₂T_x/rGO electrode displayed good repeatability, selectivity, and proved to be available for real sample analysis.

Emerging MXene-Polymer Hybrid Nanocomposites for High-Performance Ammonia Sensing and Monitoring

Ammonia (NH3) is a vital compound in diversified fields, including agriculture, automotive, chemical, food processing, hydrogen production and storage, and biomedical applications. Its extensive industrial use and emission have emerged hazardous to the ecosystem and have raised global public health concerns for monitoring NH3 emissions and implementing proper safety strategies. These facts created emergent demand for translational and sustainable approaches to design efficient, affordable, and high-performance compact NH3 sensors. Commercially available NH3 sensors possess three major bottlenecks: poor selectivity, low concentration detection, and room-temperature operation. State-of-the-art NH3 sensors are scaling up using advanced nano-systems possessing rapid, selective, efficient, and enhanced detection to overcome these challenges. MXene-polymer nanocomposites (MXP-NCs) are emerging as advanced nanomaterials of choice for NH3 sensing owing to their affordability, excellent conductivity, mechanical flexibility, scalable production, rich surface functionalities, and tunable morphology. The MXP-NCs have demonstrated high performance to develop next-generation intelligent NH3 sensors in agricultural, industrial, and biomedical applications. However, their excellent NH3-sensing features are not articulated in the form of a review. This comprehensive review summarizes state-of-the-art MXP-NCs fabrication techniques, optimization of desired properties, enhanced sensing characteristics, and applications to detect airborne NH3. Furthermore, an overview of challenges, possible solutions, and prospects associated with MXP-NCs is discussed.

Comparative antibacterial activity of 2D materials coated on porous-titania

Plasma electrolytic oxidation (PEO) is a well-established technique for the treatment of titanium-based materials. The formed titania-PEO surface can improve the osseointegration properties of titanium implants. Nevertheless, it can not address bacterial infection problems associated with bone implants. Recently, 2-dimensional (2D) materials such as graphene oxide (GO), MXene, and hexagonal boron nitride (hBN) have received considerable attention for surface modifications showing their antibacterial properties. In this paper, a comparative study on the effect of partial deposition of these three materials over PEO titania substrates on the antibacterial efficiency and bioactivity is presented. Their partial deposition through drop-casting instead of continuous film coating is propsed to simultaneously address both antibacterial and osseointegration abilities. Our results demonstrate the dose-dependent nature of the deposited antibacterial agent on the PEO substrate. GO-PEO and MXene-PEO samples showed the highest antibacterial activity with 70 (±2) % and 97 (±0.5) % inactivation of S. aureus colonies in the low concentration group, respectively. Furthermore, only samples in the higher concentration group were effective against E. coli bacteria with 18 (±2) % and 17 (±4) % decrease in numbers of colonies for hBN-PEO and GO-PEO samples, respectively. Moreover, all antibacterial samples demonstrated acceptable bioactivity and good biocompatibility, making them a considerable candidates for the next generation of antibacterial titanium implants.

Ambient-Stable Two-Dimensional Titanium Carbide (MXene) Enabled by Iodine Etching

MXene (e.g., Ti3 C2 ) represents an important class of two-dimensional (2D) materials owing to its unique metallic conductivity and tunable surface chemistry. However, the mainstream synthetic methods rely on the chemical etching of MAX powders (e.g., Ti3 AlC2 ) using hazardous HF or alike, leading to MXene sheets with fluorine termination and poor ambient stability in colloidal dispersions. Here, we demonstrate a fluoride-free, iodine (I2 ) assisted etching route for preparing 2D MXene (Ti3 C2 Tx , T=O, OH) with oxygen-rich terminal groups and intact lattice structure. More than 71 % of sheets are thinner than 5 nm with an average size of 1.8 μm. They present excellent thin-film conductivity of 1250 S cm-1 and great ambient stability in water for at least 2 weeks. 2D MXene sheets with abundant oxygen surface groups are excellent electrode materials for supercapacitors, delivering a high gravimetric capacitance of 293 F g-1 at a scan rate of 1 mV s-1 , superior to those made from fluoride-based etchants (<290 F g-1 at 1 mV s-1 ). Our strategy provides a promising pathway for the facile and sustainable production of highly stable MXene materials.

2D MXenes: Tunable Mechanical and Tribological Properties

2D transition metal carbides, nitrides, and carbonitrides, known as MXenes, were discovered in 2011 and have grown to prominence in energy storage, catalysis, electromagnetic interference shielding, wireless communications, electronic, sensors, and environmental and biomedical applications. In addition to their high electrical conductivity and electrochemically active behavior, MXenes' mechanical properties, flexibility, and strong adhesion properties play crucial roles in almost all of these growing applications. Although these properties prove to be critical in MXenes' impressive performance, the mechanical and tribological understanding of MXenes, as well as their relation to the synthesis process, is yet to be fully explored. Here, a fundamental overview of MXenes' mechanical and tribological properties is provided and the effects of MXenes' compositions, synthesis, and processing steps on these properties are discussed. Additionally, a critical perspective of the compositional control of MXenes for innovative structural, low-friction, and low-wear performance in current and upcoming applications of MXenes is provided. It is established here that the fundamental understanding of MXenes' mechanical and tribological behavior is essential for their quickly growing applications.

Supercapacitors based on Ti3C2Tx MXene extracted from supernatant and current collectors passivated by CVD-graphene

An ultrahigh capacity supercapacitor is fabricated using a nano-layered MXene as an active electrode material, and Ni-foil is used as a current collector. The high-quality Ti₃C₂T_x obtained from supernatant during etching and washing processes improves the specific capacitance significantly. As another strategy, the surface of Ni-foil is engineered by coating chemical vapor deposition-grown graphene. The graphene grown directly on the Ni-foil is used as a current collector, forming the electrode structure of Ti₃C₂T_x/graphene/Ni. The surface passivation of the current collectors has a high impact on charge-transfer, which in turn increases the capacitance of the supercapacitors. It is found that the capacitance of the graphene-based supercapacitors is more than 1.5 times of the capacitance without graphene. A high specific capacitance, ~ 542 F/g, is achieved at 5 mV/s scan rate based on cyclic voltammetry analysis. Also, the graphene-based supercapacitor exhibits a quasi-rectangular form in cyclic voltammetry curves and a symmetric behavior in charge/discharge curves. Furthermore, cyclic stability up to 5000 cycles is confirmed with high capacitance retention at high scan rate 1000 mV/s. A reduced series resistance with a high limit capacitance is revealed by equivalent circuit analysis with the Nyquist plot.

Effect of Ti3C2T x MXenes etched at elevated temperatures using concentrated acid on binder-free supercapacitors

The effect of Ti₃C₂T_x MXene etched at different temperatures (25 °C, 50 °C, and 80 °C) on the capacitance of supercapacitors without the use of conducting carbon-black or a binder was studied. The MXene etched using concentrated HCl acid (12 M)/LiF was used as an active electrode and Ni-foil as a current collector. It was observed that the elevated etching temperature facilitates the etching of the MAX phase and the exfoliation of MXene layers. However, this led to the formation of additional functional groups at the MXene surface as the temperature was increased to 80 °C. The specific capacitance of Ti₃C₂T_x-based supercapacitors increased from 581 F g⁻¹ for MXene etched at 25 °C to 657 F g⁻¹ for those etched at 50 °C at the scan rate of 2 mV s⁻¹. However, the specific capacitance reduced to 421 F g⁻¹ as the etching temperature was increased to 80 °C at the same scan rate. The supercapacitors based on MXenes etched at the intermediate temperature (50 °C) exhibited higher specific capacitance in a wide range of scan rate, symmetry in charge/discharge curves, high cyclic stability at a scan rate of 1000 mV s⁻¹ for up to 3000 cycles. The electrochemical impedance spectroscopy studies indicated low series resistance, reduced charge-transfer resistance, and decreased Warburg impedance for the supercapacitor based on the MXene etched at the intermediate temperature.

The effect of Ti₃C₂T_x MXene etched at different temperatures (25 °C, 50 °C, and 80 °C) on the capacitance of supercapacitors without the use of conducting carbon-black or a binder was studied.

Arbitrary deformable and high-strength electroactive polymer/MXene anti-exfoliative composite films assembled into high performance, flexible all-solid-state supercapacitors

Flexible all-solid-state supercapacitors (ASSSs) are excellent energy storage devices for portable/wearable electronics, although the development of an excellent comprehensive performance film electrode for the extraordinary flexible ASSSs still faces a great challenge. Here, bendable, foldable and anti-exfoliative Ti3C2Tx MXene-based films utilized as supercapacitor electrodes are reported. Polyaniline/Ti3C2Tx composites (i-PANI@Ti3C2Tx) were prepared by in situ oxidant-free polymerization of aniline on Ti3C2Tx nanosheets with p-phenylenediamine (PPD) as an initiator. Lignosulfonate (Lig) and Ti3C2Tx were constructed into a compact composite (Lig@Ti3C2Tx) film based on the hydrogen bonds formed between Lig and Ti3C2Tx. The Lig@Ti3C2Tx/i-PANI@Ti3C2Tx(5/5) hybrid film was produced by vacuum-assisted filtration of the mixed two composite dispersions. The as-prepared films can be arbitrarily deformed (such as bending and folding). They show high tensile strength and vertical-plane (the plane of film) tensile strength with 33.2 and 0.28 MPa for the i-PANI@Ti3C2Tx film, 75.4 and 0.77 MPa for the Lig@Ti3C2Tx film, and 53.7 and 0.58 MPa for the Lig@Ti3C2Tx/i-PANI@Ti3C2Tx(5/5) film (those of Ti3C2Tx film are 17.4 and 0.21 MPa), respectively. The enhanced vertical-plane tensile strength of the as-prepared composite films indicates that the large binding force generated between the Ti3C2Tx nanosheets can effectively prevent the exfoliation of films. The electrodes of the as-prepared i-PANI@Ti3C2Tx, Lig@Ti3C2Tx and Lig@Ti3C2Tx/i-PANI@Ti3C2Tx(5/5) films assembled into symmetric flexible ASSSs can deliver excellent specific capacitances of 310 F g-1 (∼1001 F cm-3), 271 F g-1 (∼881 F cm-3) and 295 F g-1 (∼959 F cm-3), respectively. In addition, the corresponding supercapacitors exhibit ultrahigh energy densities of 34.8, 30.6 and 33.3 W h L-1, respectively. It is expected that the as-prepared MXene-based films can be applied in various fields, such as electromagnetic-interference shielding and batteries. Furthermore, the as-prepared flexible ASSSs can be practically used as a wearable energy storage device.

Mechanotribological Aspects of MXene-Reinforced Nanocomposites

MXenes are recently discovered 2D nanomaterial with superior mechanical, thermal, and tribological properties, being commonly employed in a wide variety of critical research areas, ranging from cancer therapy to energy and environmental applications. Due to their special properties, such as mechanoceramic nature with excellent mechanical performance, thermal stability and rich surface properties, MXenes have tremendous potential as advanced composite structures, especially those based on polymers due to a great affinity between macromolecules and the terminating groups of 2D MXenes. MXenes have been extensively explored in metal matrix nanocomposites as well as in solid- or liquid-based lubrication systems owing to the 2D structure and antifriction characteristics. The purpose of the this paper is to provide a comprehensive insight into the material, mechanical, and tribological properties of the MXene nanolayers with discussions on the recent advancements attained from MXene-reinforced nanocomposites starting with the synthesis, fabrication techniques, intricacies of the underlying physics and mechanisms, and finally focusing on the progress in computational studies. This analysis of MXene-based composites will stimulate an emerging field with innumerable opportunities and ample potentials to produce newfangled materials and structures with targeted properties.

An effective utilization of MXene and its effect on electromagnetic interference shielding: flexible, free-standing and thermally conductive composite from MXene–PAT–poly(p-aminophenol)–polyaniline co-polymer

MXene and conductive polymers are attractive candidates for electromagnetic interference shielding (EMI) applications. The MXene–PAT-conductive polymer (CP) composites were fabricated by a cost-effective spray coating technique and characterized using X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), X-ray diffraction (XRD) and Raman spectroscopy. A new approach has been developed for the synthesis of exfoliated MXene. The MXene–PAT–poly(p-aminophenol)–polyaniline co-polymer composite exhibited good electric conductivity (EC) of 7.813 S cm⁻¹. The composites revealed an excellent thermal properties, which were 0.687 W (m K)⁻¹ thermal conductivity, 2.247 J (g K)⁻¹ heat capacity, 0.282 mm² s⁻¹ thermal diffusivity and 1.330 W s^1/2 m⁻² K⁻¹ thermal effusivity. The composites showed 99.99% shielding efficiency and the MXene–PAT–PANI–PpAP composite (MXPATPA) had EMI shielding effectiveness of 45.18 dB at 8.2 GHz. The reduced form of MXene (r-Ti₃C₂T_x) increased the shielding effectiveness (SE) by 7.26% and the absorption (SE_A) was greatly enhanced by the ant farm like structure. The composites possess excellent thermal and EMI SE characteristics, thus can be applied in areas, such as mobile phones, military utensils, heat-emitting electronic devices, automobiles and radars.

MXene and conductive polymers are attractive candidates for electromagnetic interference shielding (EMI) applications.