Aging of drinking water transmission pipes during long-term operation as a potential source of nano- and microplastics

Microplastics (MPs) and nanoplastics (NPs) released into drinking water from transmission pipes can pose a potential health risk to consumers. This paper presents the results of a comprehensive study of PE and PVC pipes after long-term operation in drinking water distribution networks, which confirmed that degradable polymers can be a significant source of MPs. Both plastics age relatively quickly, and the degree of damage to the pipe surface depends on the time and operating conditions. During aging, polymer chains deteriorate, leading to a weakening of the structure and increased amorphousness of the plastics. As a result, the surfaces of PE and PVC crack and peel, resulting in the formation of particles with sizes corresponding to NP and MP with high potential for release into water. The magnitude of the phenomenon increases as the diameter of the pipes decreases, indicating that the most vulnerable customers are those at the ends of the network to which drinking water is supplied through small-diameter pipes. Aging PE and PVC pipes should be considered a real and very important source of MPs and NPs in drinking water, and water quality in this aspect should be monitored by manufacturers.

Influence of biofilm and calcium carbonate scaling on lead transport in plastic potable water pipes: A laboratory and molecular dynamics study

This study investigated lead (Pb) transport through new, biofilm-laden, and calcium carbonate-scaled crosslinked polyethylene (PEX-A) and high-density polyethylene (HDPE) potable water pipes. The research focused on Pb accumulation through short-term exposure incidents (6 h) and Pb release for a longer duration (5 d). A mechanistic investigation of the surface morphology variations of plastic pipes following biofilm and scale formation has been conducted. The nanoscale surface asperities in new PEX-A pipes and microscale roughness features in new HDPE pipes supported the differences in biofilm abundance, scale formation, and metal uptake results between these two pipes. Biomass analysis and dissolved organic matter (DOM) quantification using three-dimensional excitation emission spectroscopy revealed a greater release of biofilm biomass during the Pb accumulation and release experiments from biofilm-laden HDPE pipes. Both biofilm-laden plastic pipes accumulated a significantly greater level of Pb compared to the new and scaled pipes. However, scaled pipes showed the highest Pb release, while biofilm-laden pipes released the least. Additionally, investigation of Pb2+ exchange from the pipe surface in the presence of Ca2+ in the solution indicated that divalent cations in water can trigger further Pb release from the pipe surface. Furthermore, the molecular dynamics simulation provided valuable insights into the interaction between different pipe surfaces with Pb with respect to affinity and binding energy.

Coaggregation dynamics in drinking water biofilms and implications for chlorine disinfection

Biofilms in drinking water (DW) systems persistently challenge traditional disinfection methods due to intricate microbial interactions, with coaggregation playing a crucial role in forming multispecies biofilms. This study examined the implications of coaggregation on tolerance towards sodium hypochlorite (NaOCl) disinfection. Dual-species biofilms were formed for seven days on polyvinyl chloride coupons, comprising a strain of the emerging pathogen Stenotrophomonas maltophilia and the coaggregating strain Delftia acidovorans 005 P. For comparison, dual-species biofilms were also formed with a non-coaggregation strain (D. acidovorans 009 P). The minimum bactericidal concentration (MBC) for each planktonic strain varied (D. acidovorans: 1 mg/L, S. maltophilia: 1.5 mg/L) below the safe DW treatment limits. However, high NaOCl doses (10 ×MBC and 100 ×MBC,) showed low efficacy against dual-species biofilms, indicating significant biofilm tolerance to disinfection. Membrane damage occurred at sub-MBC without culturability loss, underscoring biofilm resilience. The biofilm analysis revealed a complex interplay between the composition of extracellular polymeric substances and the architecture, which was influenced by the presence of the coaggregating strain. Overall, coaggregation significantly influenced biofilm formation and resilience, impacting NaOCl disinfection. These findings underscore the challenges of microbial interactions in biofilms, emphasizing the need for improved disinfection strategies to control biofilms in drinking water systems.

The impact of methylparaben and chlorine on the architecture of Stenotrophomonas maltophilia biofilms

The biofilm architecture is significantly influenced by external environmental conditions. Biofilms grown on drinking water distribution systems (DWDS) are exposed to environmental contaminants, including parabens, and disinfection strategies, such as chlorine. Although changes in biofilm density and culturability from chemical exposure are widely reported, little is known about the effects of parabens and chlorine on biofilm morphology and architecture. This is the first study evaluating architectural changes in Stenotrophomonas maltophilia colony biofilms (representatives of bacterial communities presented in DWDS) induced by the exposure to methylparaben (MP) at environmental (15 μg/L) and in-use (15 mg/L) concentrations, and chlorine at 5 mg/L, using widefield epi-fluorescence mesoscopy with Mesolens. The GFP fluorescence of colony biofilms allowed the visualization of internal structures and Nile Red fluorescence permitted the inspection of the distribution of lipids. Our data show that exposure to MP triggers physiological and morphological adaptation in mature colony biofilms by increasing the complexity of internal structures, which may confer protection to embedded cells from external chemical molecules. These architectural modifications include changes in lipid distribution as an adaptive response to MP exposure. Although chlorine exposure affected colony biofilm diameter and architecture, the colony roundness was completely affected by the simultaneous presence of MP and chlorine. This work is pioneer in using Mesolens to highlight the risks of exposure to emerging environmental contaminants (MP), by affecting the architecture of biofilms formed by drinking water (DW) bacteria, even when combined with routine disinfection strategies.

The effects of methylparaben exposure on biofilm tolerance to chlorine disinfection

Parabens are emerging contaminants that have been detected in drinking water. Their presence in DW distribution systems (DWDS) can alter bacterial behaviour, characteristics, and structure, which may compromise DW disinfection. This work provides insights into the impact of methylparaben (MP) on the tolerance to chlorine disinfection and antibiotics from dual-species biofilms formed by Acinetobacter calcoaceticus and Stenotrophomonas maltophilia isolated from DW and grown on high-density polyethylene (HDPE) and polypropylene (PPL). Results showed that dual-species biofilms grown on PPL were more tolerant to chlorine disinfection, expressing a decrease of over 50 % in logarithmic reduction values of culturable cells in relation to non-exposed biofilms. However, bacterial tolerance to antibiotics was not affected by MP presence. Although MP-exposed dual-species biofilms grown on HDPE and PPL were metabolically more active than non-exposed counterparts, HDPE seems to be the material with lower impact on DW risk management and disinfection, if MP is present. Overall, results suggest that MP presence in DW may compromise chlorine disinfection, and consequently affect DW quality and stability, raising potential public health issues.

Impacts of water treatments on bacterial communities of biofilm and loose deposits in drinking water distribution systems

Treated drinking water is delivered to customers through drinking water distribution systems (DWDSs). Although studies have focused on exploring the microbial ecology of DWDSs, knowledge about the effects of different water treatments on the bacterial community of biofilm and loose deposits in DWDS is limited. This study assessed the effects of additional treatments on the bacterial communities developed in 10 months' old pilot DWDSs. The results showed a similar bacterial community in the pipe-wall biofilm, which was dominated by Novosphingobium spp. (20-82 %) and Sphingomonas spp. (11-53 %), regardless of the treatment applied. The bacterial communities that were retained in the distribution systems (including pipe-wall biofilm and loose deposits) were similar to the particle-associated bacteria (PAB) in the corresponding supply water. The additional treatments showed clear effects of the removal and/or introduction of particles. The genera Aeromonas spp., Clostridium spp., Legionella spp., and Pseudomonas spp., which contain opportunistic pathogenic species, were only detected among the PAB in ion exchange system. Our study demonstrated that the biofilm community is consistent across treatments, and the contribution from bacteria in loose deposits is important but can be controlled by removing particles. These findings offer more insight into the origin and development of microbial ecology in DWDSs and suggest paths for further research on the possibility of managing the microbial ecology in distribution systems.

Full-length 16S rRNA gene sequencing reveals the operating mode and chlorination-aggravated SWRO biofouling at a nuclear power plant

Reverse osmosis (RO) membrane fouling and biological contamination problems faced by seawater desalination systems are microbiologically related. We used full-length 16S rRNA gene sequencing to assess the bacterial community structure and chlorine-resistant bacteria (CRB) associated with biofilm growth in different treatment processes under the winter mode of a chlorinated seawater desalination system in China. At the outset of the winter mode, certain CRB, such as Acinetobacter, Pseudomonas, and Bacillus held sway over the bacterial community structure, playing a pivotal role in biofouling. At the mode's end, Deinococcus and Paracoccus predominated, with Pseudomonas and Roseovarius following suit, while certain CRB genera still maintained their dominance. RO and chlorination are pivotal factors in shaping the bacterial community structure and diversity, and increases in total heterotrophic bacterial counts and community diversity in safety filters may adversely affect the effectiveness of subsequent RO systems. Besides, the bacterial diversity and culturable biomass in the water produced by the RO system remain high, and some conditionally pathogenic CRBs pose a certain microbial risk as a source of drinking water. Targeted removal of these CRBs will be an important area of research for advancing control over membrane clogging and ensuring water quality safety in the future.

Sunlight-triggered prebiotic nanomotors for inhibition and elimination of pathogen and biofilm in aquatic environment

Pathogen contamination in drinking water sources causes waterborne infectious diseases, seriously threatening human health. Nowadays, stimuli-responsive self-propelled nanomotors are appealing therapeutic agents for antibacterial therapy in vivo. However, achieving water disinfection using these nanobots is still a great challenge. Herein, we report on prebiotic galactooligosaccharide-based nanomotors for sunlight-regulated water disinfection. The nanomotors can utilize galactooligosaccharide-based N-nitrosamines as sunlight-responsive fuels for the spontaneous production of antibacterial nitric oxide. Such a solar-to-chemical energy conversion would power the nanomotors for self-diffusiophoresis, which could promote the diffusion of the nanomotors in water and their penetration in the biofilm, significantly enhancing the inhibition and elimination of the pathogens and their biofilms in aquatic environments. After water treatments, the prebiotic-based residual disinfectants can be selectively utilized by beneficial bacteria to effectively relieve safety risks to the environment and human health. The low-energy-cost, green and potent antibacterial nanobots show promising potential in water disinfection.

Influence of drinking water biofilm microbiome on water quality: Insights from a real-scale distribution system

Biofilms, constituting over 95 % of the biomass in drinking water distribution systems, form an ecosystem impacting both the aesthetic and microbiological quality of water. This study investigates the microbiome of biofilms within a real-scale drinking water distribution system in eastern Spain, utilizing amplicon-based metagenomics. Forty-one biofilm samples underwent processing and sequencing to analyze both bacterial and eukaryotic microbiomes, with an assessment of active biomass. Genus-level analysis revealed considerable heterogeneity, with Desulfovibrio, Ralstonia, Bradyrhizobium, Methylocystis, and Bacillus identified as predominant genera. Notably, bacteria associated with corrosion processes, including Desulfovibrio, Sulfuricella, Hyphomicrobium, and Methylobacterium, were prevalent. Potentially pathogenic bacteria such as Helicobacter, Pseudomonas, and Legionella were also detected. Among protozoa, Opisthokonta and Archaeplastida were the most abundant groups in biofilm samples, with potential pathogenic eukaryotes (Acanthamoeba, Naegleria, Blastocystis) identified. Interestingly, no direct correlation between microbiota composition and pipe materials was observed. The study suggests that the usual concentration of free chlorine in bulk water proved insufficient to prevent the presence of undesirable bacteria and protozoa in biofilms, which exhibited a high concentration of active biomass.

A review of research advances on disinfection strategies for biofilm control in drinking water distribution systems

The presence of biofilms in drinking water distribution systems (DWDS) is responsible for water quality deterioration and a possible source of public health risks. Different factors impact the biological stability of drinking water (DW) in the distribution networks, such as the presence and concentration of nutrients, water temperature, pipe material composition, hydrodynamic conditions, and levels of disinfectant residual. This review aimed to evaluate the current state of knowledge on strategies for DW biofilm disinfection through a qualitative and quantitative analysis of the literature published over the last decade. A systematic review method was performed on the 562 journal articles identified through database searching on Web of Science and Scopus, with 85 studies selected for detailed analysis. A variety of disinfectants were identified for DW biofilm control such as chlorine, chloramine, UV irradiation, hydrogen peroxide, chlorine dioxide, ozone, and others at a lower frequency, namely, electrolyzed water, bacteriophages, silver ions, and nanoparticles. The disinfectants can impact the microbial communities within biofilms, reduce the number of culturable cells and biofilm biomass, as well as interfere with the biofilm matrix components. The maintenance of an effective residual concentration in the water guarantees long-term prevention of biofilm formation and improves the inactivation of detached biofilm-associated opportunistic pathogens. Additionally, strategies based on multi-barrier processes by optimization of primary and secondary disinfection combined with other water treatment methods improve the control of opportunistic pathogens, reduce the chlorine-tolerance of biofilm-embedded cells, as well as decrease the corrosion rate in metal-based pipelines. Most of the studies used benchtop laboratory devices for biofilm research. Even though these devices mimic the conditions found in real DWDS, future investigations on strategies for DW biofilm control should include the validity of the promising strategies against biofilms formed in real DW networks.

Antibiotic resistance genes alterations in murine guts microbiome are associated with different types of drinking water

Antibiotic resistance genes (ARGs) are emerging contaminants threatening public health and commonly found in drinking water. However, the effect of different types of drinking water on ARG alterations in the gut microbiome is unclear. This study examines this issue in murine models in three phases (phase I: acclimation using ddH2O; phase II: treatment using different types of water, i.e. river water (RW), tap water (TW) and commercial bottled water (CBW); and phase III: recovery using ddH2O) using high-throughput qPCR and 16S rRNA amplicon sequencing. Results reveal that exposure to different types of drinking water could lead to significant changes in the gut microbiome, mobile genetic elements (MGEs), and ARGs. In phase II, treatment of RW and TW significantly increased the abundance of aminoglycoside and tetracycline resistance genes in mice guts (P < 0.01). In the recovery phase, consuming distilled water was found to restore ARG profiles to a certain extent in mice guts. Procrustes, network, redundancy and variation partitioning analysis indicated that ARG alterations in mice guts might relate to MGEs and bacterial communities. Our work suggests that the type of drinking water consumed may play a crucial role in shaping ARGs in gut microbiomes, emphasizing the urgent need for access to clean drinking water to mitigate the growing threat of antimicrobial resistance.

Effect of booster disinfection on the prevalence of microbial antibiotic resistance and bacterial community in a simulated drinking water distribution system

Booster disinfection was often applied to control the microorganism's growth in long-distance water supply systems. The effect of booster disinfection on the changing patterns of antibiotic resistance and bacterial community was investigated by a simulated water distribution system (SWDS). The results showed that the antibiotic resistance bacteria (ARB) and antibiotic resistance genes (ARGs) were initially removed after dosing disinfectants (chlorine and chloramine), but then increased with the increasing water age. However, the relative abundance of ARGs significantly increased after booster disinfection both in buck water and biofilm, then decreased along the pipeline. The pipe materials and disinfectant type also affected the antibiotic resistance. Chlorine was more efficient in controlling microbes and ARGs than chloramine. Compared with UPVC and PE pipes, SS pipes had the lowest total bacteria, ARB concentration, and ARB percentage, mainly due to higher disinfectant residuals and a smoother surface. The significant correlation (rs = 0.77, p < 0.001) of the 16S rRNA genes was observed between buck water and biofilm, while the correlations of targeted ARGs were found to be weak. Bray-Curtis similarity index indicated that booster disinfection significantly changed the biofilm bacterial community and the disinfectant type also had a marked impact on the bacterial community. At the genus level, the relative abundance of Pseudomonas, Sphingomonas, and Methylobacterium significantly increased after booster disinfection. Mycobacterium increased after chloramination while decreased after chlorination, indicating Mycobacterium might resist chloramine. Pseudomonas, Methylobacterium, and Phreatobacter were found to correlate well with the relative abundance of ARGs. These results highlighted antibiotic resistance shift and bacterial community alteration after booster disinfection, which may be helpful in controlling potential microbial risk in drinking water.

Realism-based assessment of the efficacy of potassium peroxymonosulphate on Stenotrophomonas maltophilia biofilm control

The potential of pentapotassium bis(peroxymonosulphate) bis(sulphate) (OXONE) to control biofilms in drinking water distribution systems (DWDS) was evaluated and compared to chlorine disinfection. Mature biofilms of drinking water (DW)-isolated Stenotrophomonas maltophilia were formed using a simulated DWDS with a rotating cylinder reactor (RCR). After 30 min of exposure, OXONE at 10 × minimum bactericidal concentration (MBC) caused a significant 4 log reduction of biofilm culturability in comparison to the unexposed biofilms and a decrease in the number of non-damaged cells below the detection limit (4.8 log cells/cm2). The effects of free chlorine were restricted to approximately 1 log reduction in both biofilm culturability and non-damaged cells. OXONE in synthetic tap water (STW) at 25 ºC was more stable over 40 days than free chlorine in the same conditions. OXONE solution exhibited a disinfectant decrease of about 10% of the initial concentration during the first 9 days, and after this time the values remained stable. Whereas possible reaction of chlorine with inorganic and organic substances in STW contributed to free chlorine depletion of approximately 48% of the initial concentration. Electron paramagnetic resonance (EPR) spectroscopy studies confirmed the presence of singlet oxygen and other free radicals during S. maltophilia disinfection with OXONE. Overall, OXONE constitutes a relevant alternative to conventional DW disinfection for effective biofilm control in DWDS.

Biofilm Dispersal, Reduced Viscoelasticity, and Antibiotic Sensitization via Nitric Oxide-Releasing Biopolymers

Compared to planktonic bacteria, biofilms are notoriously difficult to eradicate due to their inherent protection against the immune response and antimicrobial agents. Inducing biofilm dispersal to improve susceptibility to antibiotics is an attractive therapeutic avenue for eradicating biofilms. Nitric oxide (NO), an endogenous antibacterial agent, has previously been shown to induce biofilm dispersal, but with limited understanding of the effects of NO-release properties. Herein, the antibiofilm effects of five promising NO-releasing biopolymer candidates were studied by assessing dispersal, changes in biofilm viscoelasticity, and increased sensitization to tobramycin after treatment with NO. A threshold level of NO was needed to achieve biofilm dispersal, with longer-releasing systems requiring lower concentrations. The most positively charged NO-release systems (from the presence of primary amines) led to the greatest reduction in viscoelasticity of Pseudomonas aeruginosa biofilms. Co-treatment of tobramycin with the NO-releasing biopolymer greatly decreased the dose of tobramycin required to eradicate tobramycin-susceptible and -resistant biofilms in both cellular and tissue models.

Biofouling in Membrane Bioreactors-Mitigation and Current Status: a Review

Biological fouling as termed biofouling is caused by varied living organisms and is difficult to eliminate from the environment thus becoming a major issue during membrane bioreactors. Biofouling in membrane bioreactors (MBRs) is a crucial problem in increasing liquid pressure due to reduced pore diameter, clogging of the membrane pores, and alteration of the chemical composition of the water which greatly limits the growth of MBRs. Thus, membrane biofouling and/or microbial biofilms is a hot research topic to improve the market competitiveness of the MBR technology. Though several antibiofouling strategies (addition of bioflocculant or sponge into MBRs) came to light, biological approaches are sustainable and more practicable. Among the biological approaches, quorum sensing-based biofouling control (so-called quorum quenching) is an interesting and promising tool in combating biofouling issues in the MBRs. Several review articles have been published in the area of membrane biofouling and mitigation approaches. However, there is no single source of information about biofouling and/or biofilm formation in different environmental settings and respective problems, antibiofilm strategies and current status, quorum quenching, and its futurity. Thus, the objectives of the present review were to provide latest insights on mechanism of membrane biofouling, quorum sensing molecules, biofilm-associated problems in different environmental setting and antibiofilm strategies, special emphasis on quorum quenching, and its futurity in the biofilm/biofouling control. We believe that these insights greatly help in the better understanding of biofouling and aid in the development of sustainable antibiofouling strategies.

The impact of potassium peroxymonosulphate and chlorinated cyanurates on biofilms of Stenotrophomonas maltophilia: effects on biofilm control, regrowth, and mechanical properties

The activity of two chlorinated isocyanurates (NaDCC and TCCA) and peroxymonosulphate (OXONE) was evaluated against biofilms of Stenotrophomonas maltophilia, an emerging pathogen isolated from drinking water (DW), and for the prevention of biofilm regrowth. After disinfection of pre-formed 48 h-old biofilms, the culturability was reduced up to 7 log, with OXONE, TCCA, and NaDCC showing more efficiency than free chlorine against biofilms formed on stainless steel. The regrowth of biofilms previously exposed to OXONE was reduced by 5 and 4 log CFU cm-2 in comparison to the unexposed biofilms and biofilms exposed to free chlorine, respectively. Rheometry analysis showed that biofilms presented properties of viscoelastic solid materials, regardless of the treatment. OXONE reduced the cohesiveness of the biofilm, given the significant decrease in the complex shear modulus (G*). AFM analysis revealed that biofilms had a fractured appearance and smaller bacterial aggregates dispersed throughout the surface after OXONE exposure than the control sample. In general, OXONE has been demonstrated to be a promising disinfectant to control DW biofilms, with a higher activity than chlorine. The results also show the impact of the biofilm mechanical properties on the efficacy of the disinfectants in biofilm control.

Stability of Drinking Water Distribution Systems and Control of Disinfection By-Products

The stability of drinking water distribution systems and the management of disinfection by-products are critical to ensuring public health safety. In this paper, the interrelationships between corrosion products in the network, microbes, and drinking water quality are elucidated. This review also discusses the mechanisms through which corrosive by-products from the piping network influence the decay of disinfectants and the formation of harmful disinfection by-products. Factors such as copper corrosion by-products, CuO, Cu₂O, and Cu²⁺ play a significant role in accelerating disinfectant decay and catalyzing the production of by-products. Biofilms on pipe walls react with residual chlorine, leading to the formation of disinfection by-products (DBPs) that also amplify health risks. Finally, this paper finally highlights the potential of peroxymonosulfate (PMS), an industrial oxidant, as a disinfectant that can reduce DBP formation, while acknowledging the risks associated with its corrosive nature. Overall, the impact of the corrosive by-products of pipe scale and microbial communities on water quality in pipe networks is discussed, and recommendations for removing DBPs are presented.

Contribution to Understanding the Mechanisms Involved in Biofilm Formation, Tolerance and Control

Biofilms constitute a protected mode of growth that allows the colonizing microbial cells to survive in hostile environments, even when an antimicrobial agent is present. The scientific community has come to understand many things about the growth dynamics and behavior of microbial biofilms. It is now accepted that biofilm formation is a multifactorial process that starts with the adhesion of individual cells and (auto-)coaggregates of cells to a surface. Then, attached cells grow, reproduce and secrete insoluble extracellular polymeric substances. As the biofilm matures, biofilm detachment and growth processes come into balance, such that the total amount of biomass on the surface remains approximately constant in time. The detached cells retain the phenotype of the biofilm cells, which facilitates the colonization of neighboring surfaces. The most common practice to eliminate unwanted biofilms is the application of antimicrobial agents. However, conventional antimicrobial agents often show inefficacy in the control of biofilms. Much remains to be understood in the biofilm formation process and in the development of effective strategies for biofilm prevention and control. The articles contained in this Special Issue deal with biofilms of some important bacteria (including pathogens such as Escherichia coli, Pseudomonas aeruginosa and Staphylococcus aureus) and fungi (Candida tropicalis), providing novel insights into their formation mechanisms and implications, together with novel methods (e.g., use of chemical conjugates and combinations of molecules) that can be used to disrupt the biofilm structure and kill the colonizing cells.

Disruption of Pseudomonas aeruginosa Adherent Cells by NaCl and NaOCl in Drinking Water

The aim of this study was to compare and explain the disruptive effect of sodium chloride and sodium hypochlorite on the adherent cells of P. aeruginosa on glass slides. To this end, the surface characteristics of glass slides and P. aeruginosa were estimated using the contact angle method. In addition, the effects of NaCl and NaOCl on the attachment of the adherent cells were revealed using optical microscopy. The contact angle data showed moderate effects of NaCl and NaOCl on the P. aeruginosa surface, which became faintly more hydrophilic (21.9 mJ/m², 51.1 mJ/m²) and a stronger electrons donor (53.4 mJ/m², 54.3 mJ/m²). NaCl reversed the hydrophobicity of glass, with its surface becoming very hydrophobic (- 31.7 mJ/m²) and a weak electrons donor (7.4 mJ/m²), whereas NaOCl enhanced the hydrophobicity of glass (49.3 mJ/m²) and its electrons donor character (62.7 mJ/m²). The optical microscopy showed that NaCl caused a clear and progressive disruption of the colonization, while NaOCl had no effect. Briefly, this study suggests that a combination of NaCl and NaOCl may solve the problem of P. aeruginosa installation in water tracks.

Characterization of the aerosol produced from an aerated jet

Faucet aerators that form aerated water jets generate aerosols, which can constitute a risk of infection if the water is contaminated, particularly for vulnerable individuals near the sink. In this study, we characterize the size and trajectory of water droplets produced from an aerated jet. The detected particle diameter ranged from 3 to 150μm. The concentration of droplets in the air varied from near-zero to a maximum of 2×10¹¹particles/m³, depending on the location relative to the jet. We found four relevant categories of droplets based on their trajectories following their emission at the jet's free surface: particles with inertia high enough to escape the immediate vicinity of the jet (category 1), particles moving towards the jet (category 2), particles drawn into the aerator, which only included particles with a diameter smaller than 50μm (category 3), and particles with a near-vertical trajectory (category 4). Tracing category 1 particles to their generation location on the water interface shows a higher emission rate near the aerator. Finally, we employ a numerical model to compute the subsequent trajectories of droplets detected at the limits of the sampled domain. We find that particles whose diameter is smaller than 55μm completely dry and become airborne. Larger droplets deposit within a radius of 7cm around the jet, assuming a surface is located 20cm below the aerator tip. These results increase the fundamental understanding of the emission mechanisms of droplets in aerated jets and their fate in the sink environment.

Zwitterionic poly(sulfobetaine methacrylate)-based hydrogel coating for drinking water distribution systems to inhibit adhesion of waterborne bacteria

Presence of biofilms in drinking water distribution systems (DWDS) can be a nuisance, leading to several operational and maintenance issues (i.e., increased secondary disinfectants demand, pipe damage or increased flow resistance), and so far, no single control practice was found to be sufficiently effective. Here, we propose poly (sulfobetaine methacrylate) (P(SBMA))-based hydrogel coating application as a biofilm control strategy in DWDS. The P(SBMA) coating was synthetized through photoinitiated free radical polymerization on polydimethylsiloxane with different combinations of SBMA as a monomer, and N, N'-methylenebis (acrylamide) (BIS) as a cross-linker. The most stable coating in terms of its mechanical properties was obtained using 20% SBMA with a 20:1 SBMA:BIS ratio. The coating was characterized using Scanning Electron Microscopy, Energy Dispersive X-Ray Spectroscopy, and water contact angle measurements. The anti-adhesive performance of the coating was evaluated in a parallel-plate flow chamber system against adhesion of four bacterial strains representing genera commonly identified in DWDS biofilm communities, Sphingomonas and Pseudomonas. The selected strains exhibited varying adhesion behaviors in terms of attachment density and bacteria distribution on the surface. Despite these differences, after 4 h, presence of the P(SBMA)-based hydrogel coating significantly reduced the number of adhering bacteria by 97%, 94%, 98% and 99%, for Sphingomonas Sph5, Sphingomonas Sph10, Pseudomonas extremorientalis and Pseudomonas aeruginosa, respectively, compared to non-coated surfaces. These findings motivate further research into a potential application of a hydrogel anti-adhesive coating as a localized biofilm control strategy in DWDS, especially on materials known to promote excessive biofilm growth.

An Overview of the Impact of Pharmaceuticals on Aquatic Microbial Communities

Pharmaceuticals are present as pollutants in several ecosystems worldwide. Despite the reduced concentrations at which they are detected, their negative impact on natural biota constitutes a global concern. The consequences of pharmaceuticals' presence in water sources and food have been evaluated with a higher detail for human health. However, although most of the pharmaceuticals detected in the environment had not been designed to act against microorganisms, it is of utmost importance to understand their impact on the environmental native microbiota. Microbial communities can suffer serious consequences from the presence of pharmaceuticals as pollutants in the environment, which may directly impact public health and ecosystem equilibrium. Among this class of pollutants, the ones that have been studied in more detail are antibiotics. This work aims to provide an overview of the impacts of different pharmaceuticals on environmental biofilms, more specifically in biofilms from aquatic ecosystems and engineered water systems. The alterations caused in the biofilm function and characteristics, as well as bacteria antimicrobial tolerance and consequently the associated risks for public health, are also reviewed. Despite the information already available on this topic, the need for additional data urges the assessment of emerging pollutants on microbial communities and the potential public health impacts.

The impact of synthetic musk compounds in biofilms from drinking water bacteria

Musk fragrances have been detected in drinking water (DW) at trace concentrations. However, their impact on the microbial quality of DW has been disregarded. This work provides a pioneer evaluation of the effects of two synthetic musks contaminants, tonalide (AHTN) and galaxolide (HHCB), in microbial biofilms formed on two different surfaces, polyvinyl chloride (PVC) and stainless steel AISI 316 (SS316). Three bacterial species isolated from DW (Acinetobacter calcoaceticus, Burkholderia cepacia and Stenotrophomonas maltophilia), were used to develop 7-day-old single and mixed species biofilms. The impact of musks was assessed directly on biofilms but also on the bacteria motility, biofilm formation ability and biofilm susceptibility to chlorination. AHTN musk caused the most remarkable effects by increasing the cellular density and viability of mixed biofilms, and the extracellular polysaccharides content of biofilms on SS316. Most of the alterations caused by the direct exposure of biofilms to musks were observed when SS316 was used as an adhesion surface. In contrast, the ability to form biofilms and their susceptibility to chlorine were more affected for bacteria from HHCB-exposed biofilms on PVC. The overall results demonstrate that the presence of musks at residual concentrations influences DW bacterial dynamics, with the potential to impact the DW quality and safety. The type of plumbing material may further impact the effects of musks.

Effect of Surface Hydrophobicity on the Adsorption of a Pilus-Derived Adhesin-like Peptide

Bacterial colonization of abiotic surfaces such as those of medical implants, membrane filters, and everyday household items is a process of tremendous importance for public health. Bacteria use adhesive cell surface structures called adhesins to establish contact with abiotic surfaces. Among them, protein filaments called type IV pili are particularly important and found in many Gram-negative pathogens such as Pseudomonas aeruginosa. Understanding the interaction of such adhesin proteins with different abiotic surfaces at the molecular level thus represents a fundamental prerequisite for impeding bacterial colonization and preventing the spread of infectious diseases. In this work, we investigate the interaction of a synthetic adhesin-like peptide, PAK128-144ox, derived from the type IV pilus of P. aeruginosa with hydrophilic and hydrophobic self-assembled monolayers (SAMs). Using a combination of molecular dynamics (MD) simulations, quartz crystal microbalance with dissipation monitoring (QCM-D), and spectroscopic investigations, we find that PAK128-144ox has a higher affinity for hydrophobic than for hydrophilic surfaces. Additionally, PAK128-144ox adsorption on the hydrophobic SAM is furthermore accompanied by a strong increase in α-helix content. Our results show a clear influence of surface hydrophobicity and further indicate that PAK128-144ox adsorption on the hydrophobic surface is enthalpically favored, while on the hydrophilic surface, entropic contributions are more significant. However, our spectroscopic investigations also suggest aggregation of the peptide under the employed experimental conditions, which is not considered in the MD simulations and should be addressed in more detail in future studies.

Direct evidence of microbiological water quality changes on bacterial quantity and community caused by plumbing system

Drinking water quality deteriorates from treatment plant to customer taps, especially in the plumbing system. There is no direct evidence about what the differences are contributed by plumbing system. This study compared the water quality in the water main and at customer tap by preparing a sampling tap on the water main. The biomass was quantified by adenosine triphosphate (ATP) and the microbial community was profiled by 454 pyrosequencing. The results showed that in distribution pipes, biofilm contributed >94% of the total biomass, while loose deposits showed little contribution (< 2%) because of the low amount of loose deposits. The distribution of biological stable water had minor effects on the microbiocidal water quality regarding both quantity (ATP 1 ng/L vs. 1.7 ng/L) and community of the bacteria. Whereas the plumbing system has significant contribution to the increase of active biomass (1.7 ng/L vs. 2.9 ng/L) and the changes of bacterial community. The relative abundance of Sphingomonas spp. at tap (22%) was higher than that at water main (2%), while the relative abundance of Pseudomonas spp. in tap water (15%) was lower than that in the water from street water main (29%). Though only one location was prepared and studied, the present study showed that the protocol of making sampling tap on water main offered directly evidences about the impacts of plumbing system on tap water quality, which makes it possible to distinguish and study the processes in distribution system and plumbing system separately.

Nationwide biogeography and health implications of bacterial communities in household drinking water

Drinking water at the point of use harbors microorganisms that may pose potential risks to human health. However, the microbial diversity and health impacts of household drinking water are poorly understood, since culture-based methods only target on specific microorganisms and low biomass of drinking water hinders a high-throughput profiling. Here, we used an optimized workflow to efficiently collect microorganisms from low-biomass drinking water and performed deep sequencing of 16S rRNA genes to profile the bacterial diversity and biogeography of 110 household drinking water samples covering 38 cities of 29 provinces/regions in China, and further explored environmental drivers and potential health implications. Our analyses revealed a diverse drinking water community comprising a total of 22,771 operational taxonomic units (OTUs). The spatial turnover of drinking water communities is scale-dependent and appears to be driven largely by rainfall and water source river. The identified potential pathogenic species may have the possibility of causing health risks. Our novel insights enhance the current understanding of the diversity and biogeography of drinking water bacterial communities within a theoretical ecological framework and have further important implications for safe drinking water management and public health protection.

Does Chlorination Promote Antimicrobial Resistance in Waterborne Pathogens? Mechanistic Insight into Co-Resistance and Its Implication for Public Health

Chemical agents including chlorine and antibiotics are used extensively to control infectious microorganisms. While antibiotics are mainly used to treat bacterial infections, chlorine is widely used for microbial inactivation in the post-secondary disinfection steps of water treatment. The extensive use of these agents has been acknowledged as a driving force for the expansion of antimicrobial resistance (AMR) and has prompted discourse on their roles in the evolution and proliferation of resistant pathogens in the aquatic milieus. We live in a possible “post-antibiotic” era when resistant microbes spread at startling levels with dire predictions relating to a potential lack of effective therapeutic antibacterial drugs. There have been reports of enhancement of resistance among some waterborne pathogens due to chlorination. In this context, it is pertinent to investigate the various factors and mechanisms underlying the emergence and spread of resistance and the possible association between chlorination and AMR. We, therefore, reflect on the specifics of bacterial resistance development, the mechanisms of intrinsic and acquired resistance with emphasis on their environmental and public health implications, the co-selection for antibiotic resistance due to chlorination, biofilm microbiology, and multidrug efflux activity. In-depth knowledge of the molecular basis of resistance development in bacteria will significantly contribute to the more rational utilization of these biocidal agents and aid in filling identified knowledge gap toward curbing resistance expansion.

Chlorinated cyanurates and potassium salt of peroxymonosulphate as antimicrobial and antibiofilm agents for drinking water disinfection

The understanding of microbial susceptibility to disinfectants is an important step to provide drinking water (DW) of adequate microbiological quality. In drinking water distribution systems (DWDS) the application of disinfectants is the main approach to control microorganisms. Although chlorine has been commonly used for DW treatment, the increase of microbial resistance and the production of harmful disinfection by-products promote the necessity to seek new alternatives. This study evaluated the antimicrobial activity of sodium dichloroisocyanurate (NaDCC), trichloroisocyanuric acid (TCCA), and pentapotassium bis(peroxymonosulphate) bis(sulphate) (OXONE) against two emerging pathogens isolated from DW, Acinetobacter calcoaceticus and Stenotrophomonas maltophilia. Free chlorine from calcium hypochlorite was used for comparison. The dose and time-responses against planktonic bacteria were performed as well as the assessment of the effects on membrane integrity. Moreover, the effects against 48 h-old biofilms formed on polyvinyl chloride and stainless steel were evaluated in terms of biofilm culturability and removal. Minimum bactericidal concentrations of 2.1 and 3.1 mg/L for NaDCC, 2.5 and 3.8 mg/L for TCCA, 340 and 690 mg/L for OXONE, and 0.80 and 1.0 mg/L for free chlorine alone were obtained against S. maltophilia and A. calcoaceticus, respectively. The kinetic modeling revealed that NaDCC and TCCA caused similar inactivation rates and the time for first log reduction by OXONE was less than 10 min, for both bacteria. All the disinfectants triggered significant bacterial cytoplasmic membrane destabilization, even at sub-lethal concentrations. A 30 min treatment with the disinfectants allowed a reduction in the biofilm culturability up to 5 log. OXONE was the disinfectant with the best efficiency against both bacterial biofilms. However, none of the disinfectants caused significant biofilm removal (reduction < 1 log cells/cm²). This study highlights NaDCC, TCCA, and OXONE as promising alternatives to free chlorine for DW disinfection, particularly for planktonic growth control and biofilm culturability reduction.

Synthetic Musk Fragrances in Water Systems and Their Impact on Microbial Communities

The presence of emerging contaminants in aquatic systems and their potential effects on ecosystems have sparked the interest of the scientific community with a consequent increase in their report. Moreover, the presence of emerging contaminants in the environment should be assessed through the “One-Health” approach since all the living organisms are exposed to those contaminants at some point and several works already reported their impact on ecological interactions. There are a wide variety of concerning emerging contaminants in water sources, such as pharmaceuticals, personal care products, house-care products, nanomaterials, fire-retardants, and all the vast number of different compounds of indispensable use in routine tasks. Synthetic musks are examples of fragrances used in the formulation of personal and/or house-care products, which may potentially cause significant ecotoxicological concerns. However, there is little-to-no information regarding the effect of synthetic musks on microbial communities. This study reviews the presence of musk fragrances in drinking water and their impact on aquatic microbial communities, with a focus on the role of biofilms in aquatic systems. Moreover, this review highlights the research needed for a better understating of the impact of non-pharmaceutical contaminants in microbial populations and public health.

Ancient Oriental Wisdom still Works: Removing ARGs in Drinking Water by Boiling as compared to Chlorination

Antibiotic resistance genes (ARGs) in municipal drinking water may not be effectively removed during centralized treatment. To reduce potential health risks, water disinfection at the point-of-use scale is warranted. This study investigated the performance of boiling, a prevalent household water disinfection means, in response to ARGs contamination. We found that boiling was more efficient in inactivating both Escherichia coli and environmental bacteria compared to chlorination and pasteurization. Boiling of environmental bacteria suspension removed a much broader spectrum of ARGs and mobile genetic elements (up to 141 genes) than chlorination (up to 13 genes), such better performance was largely attributed to a stronger inactivation of chlorine-tolerant bacteria including Acinetobacter and Bacillus. Accumulation of extracellular ARGs was found during low-temperature heating (≤ 80°C) and in the initial stage of chlorination (first 3 min when initial chlorine was 5 mg/L and first 12 min when initial chlorine was 1 mg/L). These extracellular ARGs as well as the intracellular ARGs got removed as the heating temperature increased or the chlorination time prolonged. Under the same treatment time (30 min), high-temperature heating (≥ 90.1°C) damaged the DNA structure more thoroughly than chlorination (5 mg/L). Taking into account the low transferability of ARGs after DNA melting, boiling may provide an effective point-of-use approach to attenuating bacterial ARGs in drinking water and is still worth promoting in the future.

Biofilm formation under high shear stress increases resilience to chemical and mechanical challenges

The effect that the hydrodynamic conditions under which biofilms are formed has on their persistence is still unknown. This study assessed the behaviour of Pseudomonas fluorescens biofilms, formed on stainless steel under different shear stress (τw) conditions (1, 2 and 4 Pa), to chemical (benzalkonium chloride - BAC, glutaraldehyde - GLUT and sodium hypochlorite - SHC) and mechanical (20 Pa) treatments (alone and combined). The biofilms formed under different τw  showed different structural characteristics. Those formed under a higher τw were invariably more tolerant to chemical and mechanical stresses. SHC was the biocide which caused the highest biofilm killing and removal, followed by BAC. The sequential exposure to biocides and mechanical stress was found to be insufficient for effective biofilm control. A basal layer containing biofilm cells mostly in a viable state remained on the surface of the cylinders, particularly for the 2 and 4 Pa-generated biofilms.

Intermittent Water Supply Impacts on Distribution System Biofilms and Water Quality

Intermittent water supplies (IWS) are routinely experienced by drinking water distribution systems around the world, either due to ongoing operational practices or due to one off interruptions. During IWS events changing conditions may impact the endemic biofilms leading to hydraulic mobilisation of organic and inorganic materials attached to pipes walls with a resulting degradation in water quality. To study the impact of IWS on the microbiological and physico-chemical characteristics of drinking water, an experimental full-scale chlorinated pipe facility was operated over 60 days under realistic hydraulic conditions to allow for biofilm growth and to investigate flow resumption behaviour post-IWS events of 6, 48 and 144 hours. Turbidity and metal concentrations showed significant responses to flow restarting, indicating biofilm changes, with events greater than 6 hours generating more turbidity responses and hence discolouration risk. The increase in pressure when the system was restarted showed a substantial increase in total cell counts, while the subsequent increases in flow led to elevated turbidity and metals concentrations. SUVA₂₅₄ monitoring indicated that shorter times of non-water supply increased the risk of aromatic organic compounds and hence risk of disinfection-by-products formation. DNA sequencing indicated that increasing IWS times resulted in increased relative abundance of potential pathogenic microorganisms, such as Mycobacterium, Sphingomonas, and the fungi Penicillium and Cladosporium. Overall findings indicate that shorter IWS result in a higher proportion of aromatic organic compounds, which can potentially react with chlorine and increase risk of disinfection-by-products formation. However, by minimising IWS times, biofilm-associated impacts can be reduced, yet these are complex ecosystems and much remains to be understood about how microbial interactions can be managed to best ensure continued water safe supply.

Analysis of Pathogenic Bacterial and Yeast Biofilms Using the Combination of Synchrotron ATR-FTIR Microspectroscopy and Chemometric Approaches

Biofilms are assemblages of microbial cells, extracellular polymeric substances (EPS), and other components extracted from the environment in which they develop. Within biofilms, the spatial distribution of these components can vary. Here we present a fundamental characterization study to show differences between biofilms formed by Gram-positive methicillin-resistant Staphylococcus aureus (MRSA), Gram-negative Pseudomonas aeruginosa, and the yeast-type Candida albicans using synchrotron macro attenuated total reflectance-Fourier transform infrared (ATR-FTIR) microspectroscopy. We were able to characterise the pathogenic biofilms' heterogeneous distribution, which is challenging to do using traditional techniques. Multivariate analyses revealed that the polysaccharides area (1200-950 cm^-1) accounted for the most significant variance between biofilm samples, and other spectral regions corresponding to amides, lipids, and polysaccharides all contributed to sample variation. In general, this study will advance our understanding of microbial biofilms and serve as a model for future research on how to use synchrotron source ATR-FTIR microspectroscopy to analyse their variations and spatial arrangements.

Metagenomics analysis of the key functional genes related to biofouling aggravation of reverse osmosis membranes after chlorine disinfection

Chlorine disinfection is a common technology to control biofouling in the pretreatment of the reverse osmosis (RO) system for wastewater reclamation. However, chlorine disinfection could even aggravate the RO membrane biofouling because of the changes of microbial community structure. In this study, the mechanism of biofilm formation and EPS secretion after chlorine disinfection was investigated by analyzing the genes coding quorum sensing, exopolysaccharide biosynthesis, and amino acid biosynthesis. After 1, 5, and 15 mg-Cl₂/L chlorine disinfection, the relative abundances of the functional genes all increased significantly. Compared with the control group, chlorine-resistant bacteria (Acidovorax, Arenimonas, and Pseudomonas) also harbored higher relative abundances of these functional genes. The high relative abundances of these genes might provide the bacterial community after chlorine disinfection with high potential of biofilm formation and EPS secretion and then cause severe RO membrane biofouling. In the sample with 5 mg-Cl₂/L chlorine disinfection, the correlation coefficients (r) between each two of the three kinds of functional genes were more than 0.9 and much stronger than that in the control group. These results indicated that the bacterial community selected by chlorine disinfection could build more stable biofilm to resist chlorine but also could cause more severe RO membrane biofouling.

Water delivery system effects on coliform bacteria in tap water in First Nations reserves in Manitoba, Canada

About one-half of the homes on First Nations (FN) reserves in Manitoba, Canada, receive piped water from a water treatment plant (WTP). Many other homes (31%) are equipped with cisterns that are filled by a water truck, and our objective was to determine how the use of cisterns affects drinking water safety relative to drinking water piped directly to homes from the WTP. The study included belowground concrete cisterns, belowground fiberglass cisterns, and aboveground polyethylene cisterns stored in insulated shelters, and all the data collection methods showed that the tap water in homes with cisterns were relatively more contaminated with coliform bacteria than the tap water in piped homes. The frequency and severity of Escherichia coli and total coliform contamination were numerically greater in drinking water samples from belowground concrete and fiberglass cisterns than in piped water samples in each community, and the contamination of belowground cisterns by coliform bacteria was greatest in late spring. As well, data obtained under the Access to Information Act showed no statistical differences in the percent of satisfactory samples (no detects) between 2014 and 2018, suggesting no clear indication of improved water quality in any of the Tribal Councils in which these three and other communities are a member off. Our results point to the need for additional treatment of drinking water in homes supplied by belowground concrete or fiberglass cisterns and replacement of belowground cisterns with aboveground cisterns or piped water to reduce the risk of water-borne illnesses.

Electrochemical biofilm control by reconstructing microbial community in agricultural water distribution systems

Biofilm causes considerable technical challenges in agricultural water distribution systems. Electrochemical treatment (ECT) is a potential technique for controlling biofilm in the systems. Given the limited information on how ECT performance changes of irrigation systems and microbial biofilm community shifts. In this study, the effect of anti-biofilm was assessed. Illumina Miseq high-throughput sequencing, combined with molecular ecological network analysis, were applied to detect the effects of ECT on attached biofilm microbial communities. We found that ECT effectively mitigated biofilm formation with the fixed-biofilm biomass reduced by 37.5 %-79.9 %. ECT significantly shifted the bacterial community structures in the biofilm, reduced the communities' diversity, and changed the dominant species. Molecular ecological network analysis showed that the complexity and size of bacterial networks were destabilized under ECT and decreased the interactions among bacterial species. The reconstruction in bacterial community and networks were responsible for the decline in extracellular polymer substances and biofilm biomass. However, chlorine-resistant bacteria were found increased after ECT, and higher relative abundance and low biofilm removal was identified in continuous ECT as compared with intermittent ECT. These results aimed to highlight the opportunity for biofouling mitigation by ECT for irrigation systems, and reveal the potential anti-biofilm microbial mechanisms of ECT.

Review on Stress Tolerance in Campylobacter jejuni

Campylobacter spp. are the leading global cause of bacterial colon infections in humans. Enteropathogens are subjected to several stress conditions in the host colon, food complexes, and the environment. Species of the genus Campylobacter, in collective interactions with certain enteropathogens, can manage and survive such stress conditions. The stress-adaptation mechanisms of Campylobacter spp. diverge from other enteropathogenic bacteria, such as Escherichia coli, Salmonella enterica serovar Typhi, S. enterica ser. Paratyphi, S. enterica ser. Typhimurium, and species of the genera Klebsiella and Shigella. This review summarizes the different mechanisms of various stress-adaptive factors on the basis of species diversity in Campylobacter, including their response to various stress conditions that enhance their ability to survive on different types of food and in adverse environmental conditions. Understanding how these stress adaptation mechanisms in Campylobacter, and other enteric bacteria, are used to overcome various challenging environments facilitates the fight against resistance mechanisms in Campylobacter spp., and aids the development of novel therapeutics to control Campylobacter in both veterinary and human populations.

The role of biofilm in the development and dissemination of ubiquitous pathogens in drinking water distribution systems: an overview of surveillance, outbreaks, and prevention

A variety of pathogenic microorganisms can survive in the drinking water distribution systems (DWDS) by forming stable biofilms and, thus, continually disseminating their population through the system's dynamic water bodies. The ingestion of the pathogen-contaminated water could trigger a broad spectrum of illnesses and well-being-related obstacles. These waterborne diseases are a significant concern for babies, pregnant women, and significantly low-immune individuals. This review highlights the recent advances in understanding the microbiological aspects of drinking water quality, biofilm formation and its dynamics, health issues caused by the emerging microbes in biofilm, and approaches for biofilm investigation its prevention and suppression in DWDS.

Pseudomonas putida as a potential biocontrol agent against Salmonella Java biofilm formation in the drinking water system of broiler houses

Background

Environmental biofilms can induce attachment and protection of other microorganisms including pathogens, but can also prevent them from invasion and colonization. This opens the possibility for so-called biocontrol strategies, wherein microorganisms are applied to control the presence of other microbes. The potential for both positive and negative interactions between microbes, however, raises the need for in depth characterization of the sociobiology of candidate biocontrol agents (BCAs). The inside of the drinking water system (DWS) of broiler houses is an interesting niche to apply BCAs, because contamination of these systems with pathogens plays an important role in the infection of broiler chickens and consequently humans. In this study, Pseudomonas putida, which is part of the natural microbiota in the DWS of broiler houses, was evaluated as BCA against the broiler pathogen Salmonella Java.

Results

To study the interaction between these species, an in vitro model was developed simulating biofilm formation in the drinking water system of broilers. Dual-species biofilms of P. putida strains P1, P2, and P3 with S. Java were characterized by competitive interactions, independent of P. putida strain, S. Java inoculum density and application order. When equal inocula of S. Java and P. putida strains P1 or P3 were simultaneously applied, the interaction was characterized by mutual inhibition, whereas P. putida strain P2 showed an exploitation of S. Java. Lowering the inoculum density of S. Java changed the interaction with P. putida strain P3 also into an exploitation of S. Java. A further increase in S. Java inhibition was established by P. putida strain P3 forming a mature biofilm before applying S. Java.

Conclusions

This study provides the first results showing the potential of P. putida as BCA against S. Java in the broiler environment. Future work should include more complex microbial communities residing in the DWS, additional Salmonella strains as well as chemicals typically used to clean and disinfect the system.

Supplementary Information

The online version contains supplementary material available at 10.1186/s12866-020-02046-5.

Copper Surfaces in Biofilm Control

Biofilms are structures comprising microorganisms associated to surfaces and enclosed by an extracellular polymeric matrix produced by the colonizer cells. These structures protect microorganisms from adverse environmental conditions. Biofilms are typically associated with several negative impacts for health and industries and no effective strategy for their complete control/eradication has been identified so far. The antimicrobial properties of copper are well recognized among the scientific community, which increased their interest for the use of these materials in different applications. In this review the use of different copper materials (copper, copper alloys, nanoparticles and copper-based coatings) in medical settings, industrial equipment and plumbing systems will be discussed considering their potential to prevent and control biofilm formation. Particular attention is given to the mode of action of copper materials. The putative impact of copper materials in the health and/or products quality is reviewed taking into account their main use and the possible effects on the spread of antimicrobial resistance.

The destruction of Escherichia coli adhered to pipe surfaces in a model drinking water distribution system via various antibiofilm agents

The aim of the study is to estimate the effectiveness of three antibiofilm agents against Escherichia coli biofilm that formed in six different types of pipelines. A laboratory-scale water system was built for this work to allow for the creation of biofilm in the pipelines studied. The level of the growth rate of E. coli biofilm cells was monitored over 90 days on those tested pipe materials. The results of bacterial cell densities displayed that the highest biofilm growth was observed in the biofilm formed on the iron (Fe) pipe. In contrast, the biofilm formation rate was significantly lower on copper (Cu) pipe compared to other materials. Three antibiofilm agents, including chlorine, silver ions (Ag⁺ ), and silver nanoparticles (AgNPs), were employed to eradicate the biofilm cells. E. coli counts indicated that AgNPs are more efficient in destructing any formed biofilm cells on all tested materials. At the same time, the chlorine was only useful in the case of biofilm developed on plastic and Cu. However, the antibiofilm efficiency of Ag⁺ performs similarly to chlorine against E. coli biofilm cells. Ultimately, AgNPs are considred the most powerful antibiofilm agent among the other agents toward the biofilm cells in their maturation stage, which offers an encouraging way for the long-term functioning of water systems. PRACTITIONER POINTS: The growth rate of E. coli biofilm cells was investigated on different materials. The count of biofilm cells developed on iron pipes was higher than other materials. The E. coli biofilm on iron pipe could resist chlorine and AgNPs to a large extent. The developed biofilm on copper pipe was more sensitive to chlorine, Ag⁺ . and AgNPs. The biofilm cells could be easily eradicated from plastic-based materials with all tested disinfectants.

Occurrence of filamentous fungi in drinking water: their role on fungal-bacterial biofilm formation

Water is indispensable to life and safe and accessible supply must be available to all. The presence of microorganisms is a threat to this commitment. Biofilms are the main reservoir of microorganisms inside water distribution systems and they are extremely ecologically diverse. Filamentous fungi and bacteria can coexist inside these systems forming inter-kingdom biofilms. This review has the goal of summarizing the most relevant and recent reports on the occurrence of filamentous fungi in water distribution systems along with the current knowledge and gaps about filamentous fungal biofilm formation. Special focus is given on fungal-bacterial interactions in water biofilms.

Intra-colony channels in E. coli function as a nutrient uptake system

The ability of microorganisms to grow as aggregated assemblages has been known for many years, however their structure has remained largely unexplored across multiple spatial scales. The development of the Mesolens, an optical system which uniquely allows simultaneous imaging of individual bacteria over a 36 mm2 field of view, has enabled the study of mature Escherichia coli macro-colony biofilm architecture like never before. The Mesolens enabled the discovery of intra-colony channels on the order of 10 μm in diameter, that are integral to E. coli macro-colony biofilms and form as an emergent property of biofilm growth. These channels have a characteristic structure and re-form after total mechanical disaggregation of the colony. We demonstrate that the channels are able to transport particles and play a role in the acquisition of and distribution of nutrients through the biofilm. These channels potentially offer a new route for the delivery of dispersal agents for antimicrobial drugs to biofilms, ultimately lowering their impact on public health and industry.

Safety and Effectiveness of Monochloramine Treatment for Disinfecting Hospital Water Networks

The formation of potentially carcinogenic N-nitrosamines, associated with monochloramine, requires further research due to the growing interest in using this biocide for the secondary disinfection of water in public and private buildings. The aim of our study was to evaluate the possible formation of N-nitrosamines and other toxic disinfection by-products (DBPs) in hospital hot water networks treated with monochloramine. The effectiveness of this biocide in controlling Legionella spp. contamination was also verified. For this purpose, four different monochloramine-treated networks, in terms of the duration of treatment and method of biocide injection, were investigated. Untreated hot water, municipal cold water and, limited to N-nitrosamines analysis, hot water treated with chlorine dioxide were analyzed for comparison. Legionella spp. contamination was successfully controlled without any formation of N-nitrosamines. No nitrification or formation of the regulated DBPs, such as chlorites and trihalomethanes, occurred in monochloramine-treated water networks. However, a stable formulation of hypochlorite, its frequent replacement with a fresh product, and the routine monitoring of free ammonia are recommended to ensure a proper disinfection. Our study confirms that monochloramine may be proposed as an effective and safe strategy for the continuous disinfection of building plumbing systems, preventing vulnerable individuals from being exposed to legionellae and dangerous DBPs.

The limitations of hydrodynamic removal of biofilms from the dead-ends in a model drinking water distribution system

Biofilm formation and removal from dead-ends is a particularly difficult and understudied area of water distribution system biology. In this work, we have built a model drinking water distribution system to probe the effect of different hydrodynamic flow regimes on biofilm formation and removal in the main pipe and in the dead-end. The test rig was built to include all major drinking water distribution system components with materials and dimensions used in standard plumbing systems. We have simulated the effect of stagnant, laminar, turbulent, and intense turbulent flushing conditions on the growth and removal of biofilms from the main pipe and the dead-end. The growth of the biofilm in the main pipe was not prevented at a volumetric flow rate of 9.4 L min^-1 and flow velocity of 2 m s^-1. Mature biofilms were more difficult to remove. Biofilms grown under shear stress conditions could withstand significantly higher shear stresses than those to which they were exposed to during growth. The biofilms grew twice as fast in the dead-end when flow in the main pipe was turbulent compared to stagnant conditions. Biofilms in the dead-end were not affected by the flushing conditions in the main pipe (Q = 52 L min^-1, Re = 9.0 · 10⁴). The computational fluid dynamics simulation suggests that biofilms cannot be hydrodynamically removed from the dead-end at depths that are larger than one pipe diameter. Biofilms beyond this limit present a possible source for reinoculation and recolonization of the rest of the water distribution system.

Cryptosporidium spp. in groundwater supplies intended for human consumption - A descriptive review of global prevalence, risk factors and knowledge gaps

Cryptosporidiosis is one of the leading causes of diarrhoeal illness and mortality induced by protozoan pathogens worldwide. As a largely waterborne disease, emphasis has been given to the study of Cryptosporidium spp. in surface waters, readily susceptible to pathogenic contamination. Conversely, the status of Cryptosporidium in potable groundwater sources, generally regarded as a pristine and "safe" drinking-water supply owing to (sub)-soil protection, remains largely unknown. As such, this investigation presents the first literature review aimed to ascertain the global prevalence of Cryptosporidium in groundwater supply sources intended for human consumption. Thirty-seven peer-reviewed studies were identified and included in the review. Groundwater sample and supply detection rates (estimated 10-20%) indicate Cryptosporidium is frequently present in domestic groundwater sources, representing a latent health concern for groundwater consumers. Specifically, sample (10.4%) and source (19.1%) detection rates deriving from comprehensive "temporal" investigations are put forward as representative of a contamination 'baseline' for Cryptosporidium in 'domestic' groundwater supplies. Proposed 'baseline' prevalence figures are largely applicable in preventive risk-based catchment and groundwater quality management including the formulation of Quantitative Microbial Risk Assessment (QMRA). Notwithstanding, a large geographical disparity in available investigations and lack of standardized reporting restrict the transferability of research findings. Overall, the mechanisms responsible for Cryptosporidium transport and ingress into groundwater supplies remain ambiguous, representing a critical knowledge gap, and denoting a distinctive lack of integration between groundwater and public-health sub-disciplines among investigations. Key recommendations and guidelines are provided for prospective studies directed at more integrative and multi-disciplinary research.

Survey of pathogenic bacteria of biofilms in a metropolitan drinking water distribution system

Bacteria, especially pathogenic bacteria, were detected in order to estimate the safety of drinking water distribution systems (DWDSs). Sixteen biofilms and 12 water samples (six retained and six flowing) were collected from a city DWDS in eastern China. Biofilms were observed using scanning electron microscopy. Cultivable bacteria of biofilms were counted by heterotrophic plate counts, ranging from 3.61 × 101 to 1.67 × 106 CFU·cm-2. Coliforms, Salmonella, Shigella, Vibrio and Legionella were separated by Eosin-Methylene Blue (EMB) agar, Salmonella chromogenic medium, Shigella chromogenic medium, Thiosulfate Citrate Bile Salts Sucrose (TCBS) agar and Buffered Charcoal Yeast Extract (BCYE) agar and 13/16, 8/16, 7/16, 6/16, 0/16 biofilm samples were found to be positive, respectively. Retained and flowing water samples were collected to estimate the influence of hydrodynamic conditions on biofilm detachment. All six retained water samples were positive for bacteria, the count ranged from 1.2 × 103 to 2.8 × 104 CFU·mL-1 and 2/6, 3/6, 2/6, 0/6, 0/6 samples were positive for coliforms, Salmonella, Shigella, Legionella and Vibrio, respectively. While only three of six flowing water samples were bacteria positive, the counts ranged from 102 to 103 CFU·mL-1, 2/6 were coliform positive and no pathogens were detected under testing. The results show that there are pathogens in DWDS biofilms, which can cause health-related problems if detached from their surfaces.