The fate of Microcystis aeruginosa cells during the ferric chloride coagulation and flocs storage processes

A novel chitosan and polyferric sulfate composite coagulant for biogas slurry pretreatment by simultaneous flocculation and floatation: Performance and underlying mechanisms

Biogas slurry from anaerobic digestion is rich in nutrients but has not been fully utilized due to a high content of suspended solids (SS) causing clogging during agricultural irrigation. This study aimed to evaluate the performance of a novel chitosan and polyferric sulfate (CTS-PFS) composite coagulant for simultaneous flocculation and floatation to enhance SS removal while preserving nutrients in biogas slurry. Orthogonal method was used for experimental design to determine the optimal synthesis and operational conditions of CTS-PFS. Results show that CTS-PFS outperformed individual CTS and PFS coagulant in terms of SS removal and nutrient (nitrogen, phosphorus, and potassium) preservation. Compared to individual CTS and PFS coagulation, the combination of CTS and PFS at the mass ratio of 1:6 showed significantly higher performance by 41.5 % increase in SS removal and 5.2 % reduction in nutrient loss. The improved performance of CTS-PFS was attributed to its formation of polynuclear hydroxyl complexes with ferric oxide groups (e.g. Fe-OH, Fe-O-Fe, Fe-OH-Fe and COO-Fe) to strengthen charge neutralization and adsorption bridging. Data from this study further confirm that CTS-PFS enhanced the removal of small suspended particles and dissolved organic matter in the molecular weight range of 0.4-2.0 kDa and preserved ammonia and potassium better in biogas slurry. Bubbles were generated as hydrogen ions from coagulant hydrolysis interacted with bicarbonate and carbonate in biogas slurry for removing the produced flocs by floatation. Floc flotation was more effective in CTS-PFS coagulation due to the significant production of uniform bubbles, evidenced by the reduction in the viscosity of biogas slurry.

Advances and challenges in the technologies for cyanobacterial cells removal in drinking water treatment

Harmful cyanobacteria in reservoirs pose a serious threat to drinking water safety due to the intracellular metabolites, such as toxins and unpleasant tastes & odours. Effective removal of harmful cyanobacteria with little to no cell damage is very important to ensure the safety of drinking water. This review first introduced development history of cyanobacterial removal technologies in drinking water treatment. Then, impacts of oxidation, coagulation and pre-oxidation enhanced coagulation processes on cyanobacterial removal and integrity of the cells were comprehensively evaluated and discussed. Oxidation can remove cyanobacteria, but high doses of oxidants can result in significant cell lysis and release of intracellular metabolites, especially when using chlorine or ozone. Although there is practically no cell damage during coagulation, the removal efficiency is low in many cases. Pre-oxidation may improve cyanobacterial removal by the subsequent solid-liquid separation processes, and moderate pre-oxidation with little to no cell lysis is very important. Mechanisms of interface interaction between pre-oxidants and cyanobacteria should be defined in future to ensure moderate pre-oxidation of algal cells. Fate of cyanobacterial cells in sludge is also reviewed because more and more waterworks return sludge supernatant to the inlet of plant. Damage to cyanobacterial cells in sludge depends mainly upon coagulant type and dosage, algal species, and cyanobacteria-containing sludge should be treated before cell lysis. Efficient techniques for harmless disposal of cyanobacteria-containing sludge should be developed in future. This paper will help to better understand the cyanobacterial removal processes and provide improved perspectives for future research in this field.

Characteristics of organic matter released from drinking water treatment sludge under different storage conditions: Evaluation based on activated carbon adsorbability

Recycling water from drinking water treatment sludge (DWTS) as raw water raises several problems in the drinking water supply. In this study, the impact of storage temperatures and oxygen conditions for DWTS on the characteristics of dissolved organic matter (DOM) released from sludge was evaluated in terms of adsorbability by activated carbon. Results showed that the adsorbability of the released DOM varied greatly with storage temperatures and oxygen conditions. The modified Freundlich isotherm model revealed that the average adsorption strength (KF) estimated based on dissolved organic carbon (DOC) and ultraviolet absorbance at 260 nm (UV260) varied in the ranges of 4.01-12.1 (mg g-1)1-1/n and 23.1-52.6 (L m-1 g-1)1-1/n, respectively. DOM released under the condition without aeration possessed higher adsorbability compared to DOM released under the condition with aeration (1.41-3.01 times for DOC-based; 1.14-2.28 times for UV260-based). Moreover, the KF values of fluorescence excitation-emission matrix (EEM)-based fulvic acid-like and humic acid-like substances were higher than those of tyrosine-like and tryptophan-like substances, indicating humic-like substances released from DWTS were more adsorbable than protein-like ones. The methods or adsorption conditions that can enhance the removal of protein-like substances are essential for dealing with water quality problems associated with recycling water from drinking water treatment sludge.

Effect of three commercial algaecides on cyanobacteria and microcystin-LR: implications for drinking water treatment using activated carbon

Toxic cyanobacterial blooms in aquatic ecosystems are associated to both public health and environmental concerns worldwide. Depending on the treatment technologies used, the removal capacity of cyanotoxins by drinking water treatment plants (DWTPs) is not sufficient to reach safe levels in drinking water. Likewise, controlling these blooms with algaecide may impair the efficiency of DWTPs due to the possible lysis of cyanobacterial cells and consequent release of cyanotoxins. We investigated the effects of three commercial algaecides (cationic polymer, copper sulfate, and hydrogen peroxide) on the growth parameters of the cyanobacterium Microcystis aeruginosa and the release of microcystin-LR (MC-LR). The potential interference of each algaecide on the MC-LR removal by adsorption on activated carbon (AC) was also tested through adsorption isotherms and kinetics experiments. Most algaecides significantly decreased the cell density and biovolume of M. aeruginosa, as well as increased the release of MC-LR. Interestingly, the presence of the algaecides in binary mixtures with MC-LR affected the adsorption of the cyanotoxin. Relevant adsorption parameters (e.g., maximum adsorption capacity, adsorption intensity, and affinity between MC-LR and AC) were altered when the algaecides were present, especially in the case of the cationic polymer. Also, the algaecides influenced the kinetics (e.g., by shifting the initial adsorption and the desorption constant), which may directly affect the design and operation of DWTPs. Our study indicated that algaecides can significantly impact the fate and the removal of MC-LR in DWTPs when the adsorption process is employed, with important implications for the management and performance of such facilities.

Study on the inhibition mechanism of eucalyptus tannins against Microcystis aeruginosa

Microcystis aeruginosa is the competitively dominant algal species in eutrophic waters and poses a serious threat to the aquatic ecological environment. To investigate the effects of eucalyptus tannins (TFL) and black water in eucalyptus plantations on M. aeruginosa, this study exposed M. aeruginosa to different concentrations (0 (control), 20, 50, 80, 110, and 140 mg L-1) of tannic acid (TA; hydrolyzed tannins, HT; reagent tannin), epigallocatechin gallate (EGCG; condensed tannins, CT; reagent tannin), eucalyptus tannins (TFL, complex tannin) and mixed TFL + Fe3+ solution (tannin: Fe3+ molar ratio = 1:10). The cell density, chlorophyll-a (Chl-a) content, superoxide dismutase (SOD) activity, malondialdehyde (MDA) and soluble protein (SP) contents of algae under tannin stress were determined, and the algal cell density treated with under the combination of TFL and Fe3+ was determined. The results showed a reduction in the Chl-a content of algal cells, which inhibited photosynthesis; leading to membrane lipid peroxidation; and the complexation of soluble proteins resulting in blocked protein synthesis were the main mechanisms by which tannins inhibited the growth of M. aeruginosa. TFL achieved the same inhibition of algal cells as the tannin reagent at the same concentration. At 4 d, TFL at 80 mg L-1 and above could achieve more than 54.87 % algal density inhibition. The inhibition rate of 80 mg L-1 and above TFL + Fe3+ on algal density was more than 75 %, indicating that TFL + Fe3+ had a stronger inhibitory effect on algal density. The results may facilitate the resource utilization of eucalyptus harvesting residues, explorations of the potential application of eucalyptus tannins in the control of M. aeruginosa, and provide new ideas for ecological algal inhibition in eucalyptus plantations.

Self-floating capsule of algicidal bacteria Bacillus sp. HL and its performance in the dissolution of Microcystis aeruginosa

Algicidal bacteria is considered as an efficient and environmentally friendly approach to suppress Microcystis aeruginosa (M. aeruginosa). However, algicidal bacteria in natural water is limited during the practical application due to the interference of external factors and the low reuse capability. In this study, a bio-degradation capsule for M. aeruginosa is prepared by bio-compatible sodium alginate (SA) compositing with eco-friendly ethyl cellulose (EC) to improve the property and reuse capability of algicidal bacteria. Bacterial strain HL was well immobilized and the capsule was obtained with 2% of SA, 3% of calcium chloride (CaCl₂) and 3% of EC. It has been proved that capsules immobilizing bacteria HL shows considerable advantage over traditional bio-treatment systems (free-living bacteria) and good reusable performance. A better algicidal rate of 77.67% ± 1.14% at 7th day was obtained with the use of capsule embedding 50 mL of algicidal bacteria, enhanced by 11.05% comparing with same amount of free-living bacteria. Moreover, the algicidal rate of M. aeruginosa still reached 68.57% ± 2.88% after three times repetitive use. The effect of capsules on the fluorescence and antioxidant system of M. aeruginosa indicated that the photosystems were irreversibly damaged and the antioxidant response of superoxide dismutase (SOD), peroxidase (POD) and catalase (CAT) were significantly induced. Overall, capsules prepared in this study can provide a desirable environment for algicidal bacteria HL and ensure algicidal bacteria to in-situ work well in inhibiting booms of algae.

Nature-based coagulants for drinking water treatment: An ecotoxicological overview

The intensive human activities extensively contaminated water sources making its treatment a problem of paramount importance, especially with the increasing of global population and water scarcity. The application of natural coagulants has become a promising and environmentally friendly alternative to conventional ones. This study was aimed at evaluating the efficiency of four plant extracts namely Agave americana, Carpobrotus acinaciformis, Austrocylindropuntia subulate, and Senicio anteuphorbium as natural coagulants to remove Microcystis aeruginosa cyanobacterium from water. The effects of pH (4, 5, 6, 7, 8 9, and 10) and coagulant dose (5, 10, 15, 20, 25, and 30 mg/L) on the coagulation efficiency were investigated. Results showed that plant-based extracts exhibited high coagulant abilities significantly contributing to the removal of M. aeruginosa cells up to 80% on a case-by-case basis. The ecotoxicity (Daphnia magna, Aliivibrio fischeri, Raphidocelis subcapitata, and Sorghum saccharatum) was absent or presented very slight acute toxicity up to 12.5 mg/L being S. anteuphorbium the least toxic. PRACTITIONER POINTS: Nature-based plant extracts showed removal rates up to 80%. Lower pH and A. subulate and S. anteuphorbium were the most efficient coagulants Toxicity effects were plant extracts-based and dose function. A. subulate and S. anteuphorbium were the least toxic extracts.

Adsorbents Used for Microcystin Removal from Water Sources: Current Knowledge and Future Prospects

The increasing occurrence of toxic cyanobacteria in water sources, driven by climate change and eutrophication, is of great concern worldwide today. Cyanobacterial blooms can negatively affect water bodies and generate harmful secondary metabolites, namely microcystins (MCs), which significantly impair water quality. Various adsorbents used for MC removal from water sources were assessed in this investigation. Activated carbon constitutes the most widely used adsorbent for treating contaminated waters due to its high affinity for adsorbing MCs. Alternative adsorbents have also been proposed and reported to provide higher efficiency, but the studies carried out so far in this regard are still insufficient. The mechanisms implicated in MC adsorption upon different adsorbents should be further detailed for a better optimization of the adsorption process. Certainly, adsorbent characteristics, water pH and temperature are the main factors influencing the adsorption of MCs. In this context, optimization studies must be performed considering the effectiveness, economic aspects associated with each adsorbent. This review provides guidelines for more practical field applications of the adsorption in the treatment of waters actually contaminated with MCs.

Evidence-Based Framework to Manage Cyanobacteria and Cyanotoxins in Water and Sludge from Drinking Water Treatment Plants

Freshwater bodies and, consequently, drinking water treatment plants (DWTPs) sources are increasingly facing toxic cyanobacterial blooms. Even though conventional treatment processes including coagulation, flocculation, sedimentation, and filtration can control cyanobacteria and cell-bound cyanotoxins, these processes may encounter challenges such as inefficient removal of dissolved metabolites and cyanobacterial cell breakthrough. Furthermore, conventional treatment processes may lead to the accumulation of cyanobacteria cells and cyanotoxins in sludge. Pre-oxidation can enhance coagulation efficiency as it provides the first barrier against cyanobacteria and cyanotoxins and it decreases cell accumulation in DWTP sludge. This critical review aims to: (i) evaluate the state of the science of cyanobacteria and cyanotoxin management throughout DWTPs, as well as their associated sludge, and (ii) develop a decision framework to manage cyanobacteria and cyanotoxins in DWTPs and sludge. The review identified that lab-cultured-based pre-oxidation studies may not represent the real bloom pre-oxidation efficacy. Moreover, the application of a common exposure unit CT (residual concentration × contact time) provides a proper understanding of cyanobacteria pre-oxidation efficiency. Recently, reported challenges on cyanobacterial survival and growth in sludge alongside the cell lysis and cyanotoxin release raised health and technical concerns with regards to sludge storage and sludge supernatant recycling to the head of DWTPs. According to the review, oxidation has not been identified as a feasible option to handle cyanobacterial-laden sludge due to low cell and cyanotoxin removal efficacy. Based on the reviewed literature, a decision framework is proposed to manage cyanobacteria and cyanotoxins and their associated sludge in DWTPs.

Research progress of advanced oxidation technology for the removal of Microcystis aeruginosa: a review

In recent years, cyanobacteria blooms have continued to erupt frequently, seriously jeopardizing the safety of drinking water and human health. The safe, quick, and economical removal of cyanobacteria from water bodies, especially the dominant species of cyanobacteria, Microcystis aeruginosa, has captured a lot of scientists' attention. The application of advanced oxidation technology in water treatment is very promising, but it has not yet been used in production. To further promote the application of the advanced oxidation method in water treatment, this article combines the results of advanced research in China and abroad to review this emergent technology. Briefly, advanced oxidation process methods employ various mechanisms to remove the dominant species of cyanobacteria blooms Microcystis aeruginosa. This provides a theoretical reference and support for the efficient removal of harmful cyanobacteria from water.

Removal of Microcystis aeruginosa cells using the dead cells of a marine filamentous bacterium, Aureispira sp. CCB-QB1

Inorganic and synthetic flocculants are widely investigated for removing harmful microalgae, such as Microcystis aeruginosa. However, their toxicity and non-biodegradability are shortcomings. Bioflocculants based on extracellular polysaccharides have attracted much attention as alternative flocculants. However, its high production cost is a limiting factor for applying bioflocculants. Here, we investigate the potential of the dead cells of a marine filamentous bacterium, Aureispira sp. CCB-QB1, as a novel flocculant on M. aeruginosa cells. The removal efficiency of M. aeruginosa cells by the dead cells was measured by mixing and shaking both components in a buffer with 5 mM CaCl₂ in different incubation times and concentrations of the dead cells. After that, the minimum effective concentration of CaCl₂ was determined. The combination effect of FeCl₃ and the dead cells on the removal efficiency was tested. The structure of cell aggregates consisted of the dead cells and M. aeruginosa cells were also observed using a scanning electron microscope. The maximum removal efficiency (75.39%) was reached within 3 min in the presence of CaCl₂ when 5 mg/ml of the dead cells (wet cells) were added. The optimal concentration of CaCl₂ was 5 mM. The combination of the dead cells and a low concentration of FeCl₃ (10 mg/L) with 5 mM of CaCl₂ significantly improved the removal efficiency by about 1.2 times (P < 0.05). This result indicates that the combination usage of the dead cells can reduce the use of FeCl₃. These results indicated that the dead cells could potentially be a novel biolfocculant to remove M. aeruginosa cells.

Fe2+ activating sodium percarbonate (SPC) to enhance removal of Microcystis aeruginosa and microcystins with pre-oxidation and in situ coagulation

The frequent occurrence of cyanobacterial blooms has become a concern for drinking water safety. Common pre-oxidation, which was widely considered to enhance the followed coagulation, can cause the rupture of algae cell, leading to the undesirable release of intracellular organic matter. In this study, the Fe²⁺ activating sodium percarbonate (SPC/Fe²⁺) process for pre-oxidation and in situ coagulation was proved to effectively remove Microcystis aeruginosa without damaging cell integrity at optimal combined doses of SPC (0.2 mM) and Fe²⁺ (0.2 mM). Moreover, the SPC/Fe²⁺ process can not only control the release of MCs, but also reduce extracellular MCs from 5.22 μg/L to 1.50 μg/L, due to their moderate oxidation. Meanwhile, the SPC/Fe²⁺ treatment produces low levels of residual Fe after settling. During sludge ageing, owing to oxidation damage on cells arising from the SPC/Fe²⁺ treatment, cells continually suffered severe damage and lysed on day 4, leading to large release of intracellular organic matter and MCs, correspondingly. As a result, it is worth noting that the M. aeruginosa cells in stored sludge should be treated or disposed of early. These findings support the development of a green and cost-effective technology to handle cyanobacteria-containing water based on SPC/Fe²⁺ for ensuring water quality.

One-step removal of harmful algal blooms by dual-functional flocculant based on self-branched chitosan integrated with flotation function

Harmful algal blooms induce severe environmental problems. It is challenging to remove algae by the current available treatments involving complicate process and costly instruments. Here, we developed a CaO₂@PEG-loaded water-soluble self-branched chitosan (CP-SBC) system, which can remove algae from water in one-step without additional instrumentation. This approach utilizes a novel flocculant (self-branched chitosan) integrated with flotation function (induced by CaO₂@PEG). CP-SBC exhibited better flocculation performance than commercial flocculants, which is attributed to the enhanced bridging and sweeping effect of branched chitosan. CP-SBC demonstrated outstanding biocompatibility, which was verified by zebrafish test and algae activity test. CaO₂@PEG-loaded self-branched chitosan can serve as an "Air flotation system" to spontaneous float the flocs after flocculation by sustainably released O₂. Furthermore, CP-SBC can improve water quality through minimizing dissolved oxygen depletion and reducing total phosphorus concentrations.

Can Cyanobacterial Diversity in the Source Predict the Diversity in Sludge and the Risk of Toxin Release in a Drinking Water Treatment Plant?

Conventional processes (coagulation, flocculation, sedimentation, and filtration) are widely used in drinking water treatment plants and are considered a good treatment strategy to eliminate cyanobacterial cells and cell-bound cyanotoxins. The diversity of cyanobacteria was investigated using taxonomic cell counts and shotgun metagenomics over two seasons in a drinking water treatment plant before, during, and after the bloom. Changes in the community structure over time at the phylum, genus, and species levels were monitored in samples retrieved from raw water (RW), sludge in the holding tank (ST), and sludge supernatant (SST). Aphanothece clathrata brevis, Microcystis aeruginosa, Dolichospermum spiroides , and Chroococcus minimus were predominant species detected in RW by taxonomic cell counts. Shotgun metagenomics revealed that Proteobacteria was the predominant phylum in RW before and after the cyanobacterial bloom. Taxonomic cell counts and shotgun metagenomic showed that the Dolichospermum bloom occurred inside the plant. Cyanobacteria and Bacteroidetes were the major bacterial phyla during the bloom. Shotgun metagenomics also showed that Synechococcus, Microcystis , and Dolichospermum were the predominant detected cyanobacterial genera in the samples. Conventional treatment removed more than 92% of cyanobacterial cells but led to cell accumulation in the sludge up to 31 times more than in the RW influx. Coagulation/sedimentation selectively removed more than 96% of Microcystis and Dolichospermum. Cyanobacterial community in the sludge varied from raw water to sludge during sludge storage (1-13 days). This variation was due to the selective removal of coagulation/sedimentation as well as the accumulation of captured cells over the period of storage time. However, the prediction of the cyanobacterial community composition in the SST remained a challenge. Among nutrient parameters, orthophosphate availability was related to community profile in RW samples, whereas communities in ST were influenced by total nitrogen, Kjeldahl nitrogen (N- Kjeldahl), total and particulate phosphorous, and total organic carbon (TOC). No trend was observed on the impact of nutrients on SST communities. This study profiled new health-related, environmental, and technical challenges for the production of drinking water due to the complex fate of cyanobacteria in cyanobacteria-laden sludge and supernatant.

The behaviors of Microcystis aeruginosa and microcystins during the Fe2+/persulfate (PS) preoxidation-coagulation and flocs storage period

The frequent occurrence of toxin-producing cyanobacteria blooms driven by anthropogenic eutrophication has become a major threat to aquaculture ecosystems worldwide. In this study, the behavior of M. aeruginosa cells during flocs storage period of 6 days was first investigated after pre-oxidation and coagulation of Fe²⁺/PS. Fe²⁺/PS achieved a superior removal efficiency of 90.7% for OD₆₈₀ and 90.4% for chl-a. The contents of extracellular MCs in the pre-oxidation and coagulation system were significantly (P < 0.05) lower than those in the control. A significant (P < 0.05) difference in intracellular protein between the control and the coagulated systems was observed. Three-dimensional fluorescence excitation emission matrix (EEM) was employed to investigate the variations in extracellular organic matter (EOM) during flocs storage. The results indicated the presence of four peaks, representing protein-like substances, intermediate dissolved microbial metabolites, fulvic and humic-like compounds in the Fe²⁺/PS process. And the intensities of four peaks were all decreased in the Fe²⁺/PS system compared to those in the control. A low level of accumulated residual Fe of 0.28 mg/L was observed without posing potential environmental risk. The results showed that the M. aeruginosa cells were under stressful conditions after 3-d storage due to the decomposition of extracellular polymeric substances (EPSs) and the insufficient supply of nutrients. However, SEM results indicated that no significant alteration in cell morphology was observed. Therefore, with high removal of M. aeruginosa, low MCs concentrations, and trivial cell damage, the Fe²⁺/PS preoxidation-coagulation was proved to be an environmental-friendly method for cyanobacteria removal without yielding serious secondary pollution. This work will contribute to better understanding and managing the cyanobacteria-laden aquaculture water after pre-oxidation and coagulation.

Early warning method for cyanobacteria toxin, taste and odor problems by the evaluation of fluorescence signals

Permanganate and ozone are often used in drinking water treatment plants for the oxidation of taste and odor compounds, toxins, and algae as well as the reduction of mussel activity. The disadvantage of an overuse of such oxidants is the potential lysis of cyanobacterial cells. Cell lysis causes taste and odor components as well as toxins to be released into the water, which results in the need for even more treatment to remove these compounds completely. Our research in the CLIENT-SIGN project investigated an innovative method to monitor the lysis of cyanobacteria cells: increases in a specific fluorescence emission spectrum of the cyanobacteria pigment phycocyanin were used as a proxy for cell lysis and other compounds (taste/odor, toxins) leaving the cells. We call this form of phycocyanin "free phycocyanin" or "unbound phycocyanin". By monitoring free phycocyanin via a relatively fast and inexpensive measurement, water utilities will be better able to optimize the dosage of pre-oxidation compounds to remove extracellular compounds while preventing the lysing of cells. Laboratory studies and a case study at Yangcheng Lake (adjacent to Lake Taihu, Yangcheng Lake Water Treatment Plant, Suzhou Industrial Park, China) are presented herein. An online surveillance system that monitors incoming raw water and the water after pre-oxidation is proposed to better cope with changing water conditions.

Application of N-TiO2 for visible-light photocatalytic degradation of Cylindrospermopsis raciborskii - More difficult than that for photodegradation of Microcystis aeruginosa ?

Nowadays Cylindrospermopsis raciborskii (C. raciborskii) and the metabolites produced, such as cylindrospermopsin (CYN), pose a serious threat to the ecosystem. Advanced oxidation technologies have been verified as constituting a very promising means to eliminate the risk from harmful algae. But so far little research has focused on the visible-light photocatalytic destruction of C. raciborskii cells and the degradation of their metabolites. In our study, N-doped TiO₂ (N-TiO₂) was used to degrade C. raciborskii and the degradation was compared with that of the Microcystis aeruginosa (M. aeruginosa). Results showed that although the photodegradation of C. raciborskii was more difficult than that of M. aeruginosa, the treatment with N-TiO₂ was still satisfactory. After adding 200 mg/L N-TiO₂, C. raciborskii cells (5 × 10⁶ cells/mL) were completely destroyed within 20 h under visible light irradiation, and nearly 90% of the organic matter and CYN in the suspensions were also degraded, thereby markedly improving the water quality. The photocatalytic process starts with damage to the cell membrane resulting in the leakage of internal components. Subsequently, the leaked metabolites were oxidised by the reactive oxidizing species produced by N-TiO₂. Thus, the application of N-TiO₂ is a promising method for the treatment of C. raciborskii.

Worse than cell lysis: The resilience of Oscillatoria sp. during sludge storage in drinking water treatment

Benthic Oscillatoria sp. may form dense surface blooms especially under eutrophic and calm conditions, which poses a threat to drinking water safety because it can produce toxic and odorous metabolites. This is the first study to investigate the effect of the conventional coagulant polyaluminium ferric chloride (PAFC) on removal of Oscillatoria sp., and the behavior of Oscillatoria sp. cells in sludges formed from different dosages of PAFC (control, optimum, and overdose system) during storage was also studied. Oscillatoria sp. cells can be removed efficiently by coagulation of PAFC. The adverse environmental stresses of sludge, such as lack of light and anoxic environment, decrease cell viability and induce the increase of superoxide dismutase activity (SOD) and malondialdehyde content (MDA) in Oscillatoria sp. cells during the first 4 days. Because Oscillatoria sp. can adapt to the low-light and hypoxic circumstances in sludge gradually, the cells regrow with prolonged storage time. Compared to planktonic Microcystis aeruginosa and Cylindrospermopsis raciborskii, regrowth of Oscillatoria sp. during storage may present a bigger threat, even though Microcystis aeruginosa and Cylindrospermopsis raciborskii cells will be damaged and release toxic compounds. Growth rates of algae in coagulated systems were lower than that in control system because of the restriction of flocs. It is worth noting that the chlorophyll a level was increased by a factor of 3.5 in the optimal-dose system, and worse, the overdose system increased by a factor of 6 in chlorophyll a after 8 d storage due to the benefit of higher Fe levels. Concentrations of extracellular geosmin and cylindrospermopsin also increased during storage, especially after 4 d, and varied in the following sequence for a given storage duration: control system > overdose system > optimum system. Overall, due to decrease of SOD and MDA in Oscillatoria sp. cells after 4 d storage, algae cells regrew rapidly, especially in overdose system. Hence, sludge should be treated within 4 d and excess PAFC dosing should be avoided.

Primary investigation of the antialgal activity of shrimp shell on Microcystis aeruginosa

This study aimed to explore the application potential of an eco-friendly waste-shrimp shell in Microcystis aeruginosa (M. aeruginosa) control-for the first time. Four treatments with different doses (0.75, 1.5, 3.0, and 6.0 g/L) were built to investigate the effects of shrimp shell on the growth, cell viability, physiological changes, and microcystins (MCs) release of M. aeruginosa cells. The water quality after shrimp shell treatment was also detected. Results showed that the growth of M. aeruginosa was effectively inhibited by shrimp shell, and the inhibition rates were dose-dependent within 7 days. Though shrimp shells at high doses could inhibit the cell growth greatly, the MC release was accelerated as they led to the cells lysis. While with the low shrimp shell dose (0.75 g/L), both satisfied inhibition effect and low MC release could be achieved simultaneously. For the water quality, we found that the turbidity and TN was not affected obviously with low dosage of shrimp shell, but it resulted in the increasing of COD_Mn and TP contents. In summary, the shrimp shell can be used as an effective algicide to control algal blooms but its adverse effect on COD_Mn and TP of water should be further solved.

Changes in Microcystis aeruginosa cell integrity and variation in microcystin-LR and proteins during Tanfloc flocculation and floc storage

The objective of this study was to determine the influence of Tanfloc on Microcystis aeruginosa cell integrity, microcystin-LR (MC-LR), and proteins during flocculation and floc storage. The effects of Tanfloc addition, stirring, and floc storage time were considered to minimize cell damage and the release of MC-LR and proteins. Optimal flocculation conditions (Tanfloc dosage 10.42 mg L^-1, rapid agitation for 0.36 min at 568.88 rpm and slow agitation for 14.14 min at 12.1 rpm) were obtained using the response surface methodology. Up to 98.9% of the M. aeruginosa cells were removed intact at low Tanfloc dosage. During floc storage, Tanfloc initially protected the cells. After 8 d, large-scale cell lysis occurred because Tanfloc had substantially decomposed. Nevertheless, Tanfloc also extended the extracellular MC-LR and protein release time to 8 d. This delay ensured adequate time to decontaminate sludge containing the algae, thereby reducing the risk of secondary pollution. In addition, the low cost of Tanfloc facilitates its widespread application in the management of harmful algal blooms.

Enhanced algae removal by Ti-based coagulant: comparison with conventional Al- and Fe-based coagulants

The water eutrophication caused by cyanobacteria seasonally proliferates, which is a hot potato to be resolved for water treatment plants. This study firstly investigated coagulation performance of titanium tetrachloride (TiCl₄) for Microcystis aeruginosa synthetic water treatment. Results show complete algal cell removal by TiCl₄ coagulation without damage to cell membrane integrity even under harsh conditions; 60 mg/L TiCl₄ was effective in removing the microcystins up to 85%. Furthermore, besides having stronger UV₂₅₄ removal capability and the higher removal of fluorescent substances over Al- and Fe-based coagulants, TiCl₄ coagulant required more compact coagulation and sedimentation tanks due to its significantly improved floc growth and sedimentation speed. Meanwhile, its' short hydraulic retention time avoided algal cell breakage and subsequent algal organic matter release. Microcystin concentrations were kept at a low level during sludge storage period, indicating that the TiCl₄ flocs could prevent algal cells from natural lysis. To facilitate water recycling without secondary contamination, the algae-containing sludge after TiCl₄ coagulation ought to be disposed within 12 days at 20 °C and 8 days at 35 °C.

Behavior of Cylindrospermopsis raciborskii during coagulation and sludge storage - higher potential risk of toxin release than Microcystis aeruginosa?

Owing to the global warming and its strong adaptability, Cylindrospermopsis raciborskii has spread world-wide. However, as one of toxic cyanobacteria in many drinking water sources, it has not been drawn proper consideration in drinking water treatment plants so far. The investigation aimed at unveiling the fate of C. raciborskii during polyaluminum ferric chloride (PAFC) coagulation and sludge storage, revealing its differences from Microcystis aeruginosa. Results showed that C. raciborskii cells were effectively removed intactly under optimum coagulation conditions, but PAFC at higher dosages (>10 mg/L) triggered additional cylindrospermopsins release. In sludge storage, coagulated C. raciborskii cells suffered severe oxidative damage, leading to significant cylindrospermopsins release after day 6. C. raciborskii manifested different behaviors from M. aeruginosa which cells didn't release much microcystins during coagulation and sludge storage. This was mostly due to their differences in physiology and morphology. In flocs, M. aeruginosa could be enveloped by coagulant which can protect cells against the nasty attack from outside, whereas C. raciborskii with long filaments was hard to be wrapped and prone to suffering oxidative damage. These results confirmed C. raciborskii had a higher risk of toxin release in water production process than M. aeruginosa, which should deserve more attention.

Removal of intra- and extracellular microcystin by submerged ultrafiltration (UF) membrane combined with coagulation/flocculation and powdered activated carbon (PAC) adsorption

In this study, we investigated the performance of conventional (coagulation/flocculation→powdered activated carbon [PAC] adsorption) and advanced treatment (coagulation/flocculation→PAC adsorption→submerged ultrafiltration [UF] membrane) processes separately and sequentially for the removal of total (intra- and extracellular) microcystin. Results of the conventional treatment process demonstrated that coagulation/flocculation alone was not effective (up to 70%) for the removal of total microcystin, while the uptake of total microcystin was achieved up to 84% by PAC adsorption (PAC dose of 20mg/L). In addition, the adsorption kinetic mechanism of PAC was also examined using several kinetic models. Results showed that the pseudo-second order (PSOM) and Weber-Morris intraparticle diffusion model (IPDM) are the most suitable models for this study (r²>0.98 and p-values ≤0.05). On the other hand, up to 94% of microcystin was effectively removed when the coagulation/flocculation and PAC systems were combined with UF membranes. Also, the permeate concentration was found to be 0.3mg/L, which is below the World Health Organization (WHO) guideline value of 1μg/L. Overall results indicated that higher removal of microcystin occurred using the advanced treatment process. Therefore, this combined system appears to be a promising treatment technique for the removal of total microcystin.

Potent removal of cyanobacteria with controlled release of toxic secondary metabolites by a titanium xerogel coagulant

Cyanobacteria blooming is a serious environmental issue throughout the world. Removal of cyanobacterial cells from surface water with controlled release of cyanobacterial organic matter (COM), especially toxic microcystins (MCs), would potentially reduce the processing burden in follow-up water treatment. Coagulation is a key technique in water treatment. Herein, the potential application of a novel titanium xerogel coagulant (TXC) was evaluated for the treatment of cyanobacteria-laden water in terms of cyanobacteria removal efficiency, variation of cell viability, the release and evolution of COM in the floc accumulation and storage process. Under acidic to neutral conditions, TXC showed a higher removal efficiency of approximately 99% for cyanobacteria and a lower residual Ti concentration than the widely-used commercial polyferric sulfate (PFS) and polyaluminum chloride (PAC). Another advantage of TXC was the reduced MCs concentration caused by the released acetylacetone (AcAc) from the hydrolysis of TXC. Under solar irradiation, AcAc degraded the extracellular MCs from an initial concentration of 40 μg/L to a residual concentration of 7 μg/L during a 16-day floc storage process. The low residual Ti concentration (< 0.04 mg/L) and the efficient removal of COM/MCs following TXC coagulation reduced the toxicity to photobacteria. The results demonstrate that TXC is a promising dual-effect coagulant for treatment of cyanobacteria-laden water.

16S rRNA Gene Amplicon Sequencing Reveals Significant Changes in Microbial Compositions during Cyanobacteria-Laden Drinking Water Sludge Storage

This is the first study to systematically investigate the microbial community structure in cyanobacteria-laden drinking water sludge generated by different types of coagulants (including AlCl₃, FeCl₃, and polymeric aluminum ferric chloride (PAFC)) using Illumina 16S rRNA gene MiSeq sequencing. Results show that Cyanobacteria, Proteobacteria, Firmicutes, Bacteroidetes, Verrucomicrobia, and Planctomycetes were the most dominant phyla in sludge, and because of the toxicity of high Al and Fe level in AlCl₃ and FeCl₃ sludges, respectively, the PAFC sludge exhibited greater microbial richness than that in AlCl₃ and FeCl₃ sludges. Due to lack of light and oxygen in sludge, relative abundance of the dominant genera Microcystis, Rhodobacter, Phenylobacterium, and Hydrogenophaga clearly decreased, especially after 4 days storage, and the amounts of extracellular microcystin and organic matter rose. As a result, the relative abundance of microcystin and organic degradation bacteria increased significantly, including pathogens such as Bacillus cereus, in particular after 4 days storage. Hence, sludge should be disposed of within 4 days to prevent massive growth of pathogens. In addition, because the increase of extracellular microcystins, organic matter, and pathogens in AlCl₃ sludge was higher than that in FeCl₃ and PAFC sludges, FeCl₃ and PAFC may be ideal coagulants in drinking water treatment plants.

Using quartz sand to enhance the removal efficiency of M. aeruginosa by inorganic coagulant and achieve satisfactory settling efficiency

In this study, low-cost and non-polluting quartz sand was respectively mixed with AlCl₃, FeCl₃ and PAFC to synergistically remove Microcystis aeruginosa. Results showed that quartz sand could markedly increase the algae removal efficiency and decrease the coagulant doses. The increase of removal efficiency with AlCl₃ and FeCl₃ was only due to the enhancement of floc density by the quartz sand. However, the removal efficiency with PAFC was increased not only by the enhanced floc density, but also by the enlarged floc size. Flocs from 50 mg/L sand addition were larger than that with other sand doses, which was on account of the appropriate enhancement of collision efficiency at this dose. After coagulation, the extracellular organic matter (EOM) and microcystins (MCs) in system with quartz sand was remarkably reduced. That’s because quartz sand can enhance the coagulation so as to improve capping the EOM and MCs in flocs during coagulation process. Owing to 200 mg/L quartz sand could damage the cell’s membrane during coagulation proces, algal cells in the system lysed two days earlier than with 50 mg/L sand during flocs storage. In addition, cells with PAFC incurred relatively moderate cellular oxidative damage and could remain intact for longer time.

WITHDRAWN: Removal of microcystins in water by ultrasound coupled advanced oxidation techniques

This article has been withdrawn at the request of the author(s) and/or editor. The Publisher apologizes for any inconvenience this may cause. The full Elsevier Policy on Article Withdrawal can be found at https://www.elsevier.com/about/our-business/policies/article-withdrawal.

A promising application of chitosan quaternary ammonium salt to removal of Microcystis aeruginosa cells from drinking water

This work was aimed toward studying the new application of chitosan quaternary ammonium salt (HTCC), a water-soluble chitosan derivative, on removal of Microcystis aeruginosa (M. aeruginosa) cells during HTCC coagulation and floc storage. Results showed that all cells were removed without damage under optimum coagulation conditions: HTCC dosage 1.5mg/L, rapid mixing for 0.5min at 5.04g and slow mixing for 30min at 0.20g. The high removal efficiency was due to the large size and compact structure of flocs formed by HTCC, which readily settled. During floc storage, HTCC could induce production of reactive oxygen species (ROS), which would accelerate M. aeruginosa cell lysis. But the flocs, into which the cells aggregated, could protect cells from cellular oxidative damage caused by ROS, thus keeping the cells intact for a longer time.

Characteristics of water obtained by dewatering cyanobacteria-containing sludge formed during drinking water treatment, including C-, N-disinfection byproduct formation

This is the first study to systematically investigate the characteristics of the water obtained by dewatering cyanobacteria-containing sludge generated in the drinking water treatment plant, including formation of C- and N-disinfection by-products (DBPs). Results showed that this 'dewatering water' (DW) had different properties when the sludge was stored at different times. The content of dissolved organic matter (DOM) and microcystins (MCs) in the DW were low when the sludge was treated or disposed of within 4 days; correspondingly, the C-, N-DBP production was also low. However, due to the damage of algal cells to some extent, the DOM and MC levels increased significantly for storage time longer than 4 days; the production of C-, N-DBPs also increased. There were also obvious differences in the characteristics of the DW from sludges generated with different coagulant species. Due to the better protective effect of FeCl₃ and polymeric aluminium ferric chloride (PAFC) flocs, the DOM and MC levels and the production of C-, N-DBPs in the DW with FeCl₃ and PAFC coagulation were lower than those with AlCl₃ coagulation, even though the sludges were stored for the same amount of time. Furthermore, because of the formation of Al and Fe hydroxides, precipitated onto the surface of flocs, the soluble Al and Fe in the DW decreased with increased storage time, especially in the first four days. Overall, this study revealed the trends in variation of DW quality for cyanobacteria-containing sludges formed with different coagulants, then FeCl₃ and PAFC coagulants are recommended and sludge should be treated or disposed of within 4 days.

Behaviors of Microcystis aeruginosa cells during floc storage in drinking water treatment process

This is the first study to systematically investigate the different behaviors of Microcystis aeruginosa in the sludges formed by AlCl₃, FeCl₃, and polymeric aluminium ferric chloride (PAFC) coagulants during storage. Results show that the viability of Microcystis aeruginosa in PAFC sludge was stronger than that of cells in either AlCl₃ or FeCl₃ sludge after the same storage time, while the cells’ viability in the latter two systems stayed at almost the same level. In AlCl₃ and FeCl₃ sludges high concentrations of Al and Fe were toxic to Microcystis aeruginosa, whereas in PAFC sludge low levels of Al showed little toxic effect on Microcystis aeruginosa growth and moderate amounts of Fe were beneficial to growth. The lysis of Microcystis aeruginosa in AlCl₃ sludge was more serious than that in PAFC sludge, for the same storage time. Although the cell viability in FeCl₃ sludge was low (similar to AlCl₃ sludge), the Microcystis aeruginosa cells remained basically intact after 10 d storage (similar to PAFC sludge). The maintenance of cellular integrity in FeCl₃ sludge might be due to the large floc size and high density, which had a protective effect for Microcystis aeruginosa.

Fate of cyanobacteria in drinking water treatment plant lagoon supernatant and sludge

In conventional water treatment processes, where the coagulation and flocculation steps are designed to remove particles from drinking water, cyanobacteria are also concentrated into the resultant sludge. As a consequence, cyanobacteria-laden sludge can act as a reservoir for metabolites such as taste and odour compounds and cyanotoxins. This can pose a significant risk to water quality where supernatant from the sludge treatment facility is returned to the inlet to the plant. In this study the complex processes that can take place in a sludge treatment lagoon were investigated. It was shown that cyanobacteria can proliferate in the conditions manifest in a sludge treatment lagoon, and that cyanobacteria can survive and produce metabolites for at least 10days in sludge. The major processes of metabolite release and degradation are very dependent on the physical, chemical and biological environment in the sludge treatment facility and it was not possible to accurately model the net effect. For the first time evidence is provided to suggest that there is a greater risk associated with recycling sludge supernatant than can be estimated from the raw water quality, as metabolite concentrations increased by up to 500% over several days after coagulation, attributed to increased metabolite production and/or cell proliferation in the sludge.

The performance of chitosan/montmorillonite nanocomposite during the flocculation and floc storage processes of Microcystis aeruginosa cells

This study aimed to investigate the performance of chitosan-modified nano-sized montmorillonite (CTS/NMMT) during the flocculation of Microcystis aeruginosa (MA). The release of intracellular microcystins (MCs) caused by the damage of intact MA cells during the flocculation and floc storage processes was also comprehensively evaluated through scanning electron microscopy (SEM) and measurement of K(+) and Mg(2+) release. With the application of the Box-Behnken experimental design combined with response surface methodology, the quadratic statistical model was established to predict and optimize the interactive effects of content of CTS/NMMT, weight ratio of NMMT to CTS, and agitation time on the removal efficiency of MA cells. A maximum removal of 94.7 % MA cells was observed with content of CTS/NMMT 300-320 mg L(-1), weight ratio of NMMT to CTS 14-16, and agitation time 16-50 min. During the flocculation process, CTS/NMMT aggregated MA cells as flocs and served as a protection shield for cells. The extracellular and intracellular microcystin-leucine-arginine (MC-LR) decreased remarkably and the yield of intracellular MC-LR showed a decreasing trend during the flocculation. The cell integrity was slightly damaged by the mechanical actions rather than by the flocculant. During the floc storage process, cell lysis and membrane damage were remarkably aggravated. The noticeable increase of K(+) and Mg(2+) release indicated that CTS/NMMT damaged the integrity of most MA cells in the flocs and liberated the intracellular MC-LR. Meanwhile, NMMT and CTS polymers assisted the adsorptive removal of extracellular MC-LR released to water. The flocs should be timely treated within 12 h to prevent the leakage of MCs.