A Review of the Properties and Applications of Poly (Methyl Methacrylate) (PMMA)

Comparison of methods for the synthesis of silver nanoparticles stabilized in a solid polymethacrylate matrix

Silver nanoparticles were synthesized inside the small plates of transparent polymer medium by reduction of silver cations. The difference in morphology and sizes of nanoparticles synthesized by chemical, photochemical and thermal reduction was revealed, which depends both on the component ratio of the mixture and on the reduction time for the specific component ratio The polymethacrylate matrix itself acts as the stabilizing agent. A colorimetric sensor based on polymethacrylate matrix and silver nanoparticles was developed for the detection of hydrogen peroxide. The optical properties of the sensor were characterized by spectrophotometer using the surface plasmon resonance. A colorimetric sensor with nanoparticles undergoing to thermal reduction showed a quick result for the determination of hydrogen peroxide in the range 0.2-4.4 mM with a detection limit 0.1 mM.

Disruption of early embryonic development in mice by polymethylmethacrylate nanoplastics in an oxidative stress mechanism

Polymethylmethacrylate (PMMA) has been used in many products, such as acrylic glass, and is estimated to reach 5.7 million tons of production per year by 2028. Thus, nano-sized PMMA particles in the environment are highly likely due to the weathering process. However, information on the hazards of nanoplastics, including PMMA in mammals, especially reproductive toxicity and action mechanism, is scarce. Herein, we investigated the effect of PMMA nanoplastics on the female reproductive system of mice embryos during pre-implantation. The treated plastic particles in embryos (10, 100, and 1000 μg/mL) were endocytosed into the cytoplasm within 30 min, and the blastocyst development and indices of embryo quality were significantly decreased from at 100 μg/mL. Likewise, the transfer of nanoplastic-treated embryos at 100 μg/mL decreased the morula implantation rate on the oviduct of pseudopregnant mice by 70%, calculated by the pregnant individual, and 31.8% by the number of implanted embryos. The PMMA nanoplastics at 100 μg/mL significantly increased the cellular levels of reactive oxygen species in embryos, which was not related to the intrinsic oxidative potential of nanoplastics. This study highlights that the nanoplastics that enter systemic circulation can affect the early stage of embryos. Thus, suitable action mechanisms can be designed to address nanoplastic occurrence.

Rheological Analysis and Evaluation of Measurement Techniques for Curing Poly(Methyl Methacrylate) Bone Cement in Vertebroplasty

Vertebroplasty is a minimally invasive surgical procedure used to treat vertebral fractures, which conventionally involves injecting poly(methyl methacrylate) (PMMA) bone cement into the fractured vertebra. A common risk associated with vertebroplasty is cement leaking out of the vertebra during the injection, which may occur due to a lack of understanding of the complex flow behavior. Therefore, experiments to quantify the cement's flow properties are necessary for understanding and proper handling of the bone cement. In this study, we aimed to characterize the behavior of PMMA bone cement in its curing stages to obtain parameters that govern the flow behavior during injection. We used rotational and oscillatory rheometry for our measurements, as well as a custom-made injector setup that replicated a typical vertebroplasty setting. Our results showed that the complex viscoelastic behavior of bone cement is significantly affected by deformations and temperature. We found that the results from rotational tests, often used for characterizing the bone cement, are susceptible to measurement artifacts caused by wall slip and "ridge"-like formations in the test sample. We also found the Cox-Merz rule to be conditionally valid, which affects the use of oscillatory tests to obtain the shear-thinning characteristics of bone cement. Our findings identify important differences in the measured flow behavior of PMMA bone cement when assessed by different rheological methods, an understanding that is crucial for its risk-free usage in downstream medical applications.

Recent advances in two-dimensional perovskite materials for light-emitting diodes

Light-emitting diodes (LEDs) are an indispensable part of our daily life. After being studied for a few decades, this field still has some room for improvement. In this regard, perovskite materials may take the leading role. In recent years, LEDs have become a most explored topic, owing to their various applications in photodetectors, solar cells, lasers, and so on. Noticeably, they exhibit significant characteristics in developing LEDs. The luminous efficiency of LEDs can be significantly enhanced by the combination of a poor illumination LED with low-dimensional perovskite. In 2014, the first perovskite-based LED was illuminated at room temperature. Furthermore, two-dimensional (2D) perovskites have enriched this field because of their optical and electronic properties and comparatively high stability in ambient conditions. Recent and relevant advancements in LEDs using low-dimensional perovskites including zero-dimensional to three-dimensional materials is reported. The major focus of this article is based on the 2D perovskites and their heterostructures (i.e., a combination of 2D perovskites with transition metal dichalcogenides, graphene, and hexagonal boron nitride). In comparison to 2D perovskites, heterostructures exhibit more potential for application in LEDs. State-of-the-art perovskite-based LEDs, current challenges, and prospects are also discussed.

Transparent and Colorless Luminescent Solar Concentrators Based on ZnO Quantum Dots for Building-Integrated Photovoltaics

Scientific interest in luminescent solar concentrators (LSCs) has reemerged mainly due to the application of semiconductor quantum dots (QDs) as highly efficient luminophores. Recently, LSCs have become attractive proposals for Building-Integrated photovoltaics (BIPV) since they could help conventional photovoltaics to improve sunlight harvesting and reduce production costs. However, most of the modern LSCs rely on heavy-metal QDs which are highly toxic and may cause environmental concerns. Additionally, their absorption spectra give them a characteristic color limiting their potential application in BIPV. Herein, we fabricated transparent and colorless LSCs by embedding nontoxic and cost-effective zinc oxide quantum dots (ZnO QDs) in a PMMA polymer matrix (ZnO-LSC), preserving the QD optical properties and PMMA transparency. The synthesized colloidal ZnO QDs have an average size of 5.5 nm, a hexagonal wurtzite crystalline structure, a broad yellow photoluminescent signal under ultraviolet excitation, and are highly visibly transparent at the employed concentrations (>95% in wavelengths above 400 nm). The optical characterization of the fabricated ZnO-LSCs showed a good visible transparency of 80.3% average visible transmission (AVT), with an LSC concentration factor (C) of 1.02. An optimal device (ZnO-LSC-O) could reach a C value of 2.66 with the combination of optical properties of colloidal ZnO QDs and PMMA. Finally, simulations of the performance of silicon solar cells coupled to the fabricated and optimal LSCs under standard AM 1.5G illumination were performed employing the software COMSOL Multiphysics. The fabricated ZnO-LSC achieved a simulated maximum power conversion efficiency (PCE) of 3.80%, while the optimal ZnO-LSC-O reached 5.45%. Also, the ZnO-LSC generated a maximum power of 15.02 mW and the ZnO-LSC-O generated 40.33 mW, employing the same active area as the simulated solar cell directly illuminated, which generated 14.39 mW. These results indicate that the ZnO QD-based LSCs may be useful as transparent photovoltaic windows for BIPV applications.

Development of Bioactive Hybrid Poly(lactic acid)/Poly(methyl methacrylate) (PLA/PMMA) Electrospun Fibers Functionalized with Bioglass Nanoparticles for Bone Tissue Engineering Applications

Hybrid scaffolds that are based on PLA and PLA/PMMA with 75/25, 50/50, and 25/75 weight ratios and functionalized with 10 wt.% of bioglass nanoparticles (n-BG) were developed using an electrospinning technique with a chloroform/dimethylformamide mixture in a 9:1 ratio for bone tissue engineering applications. Neat PLA and PLA/PMMA hybrid scaffolds were developed successfully through a (CF/DMF) solvent system, obtaining a random fiber deposition that generated a porous structure with pore interconnectivity. However, with the solvent system used, it was not possible to generate fibers in the case of the neat PMMA sample. With the increase in the amount of PMMA in PLA/PMMA ratios, the fiber diameter of hybrid scaffolds decreases, and the defects (beads) in the fiber structure increase; these beads are associated with a nanoparticle agglomeration, that could be related to a low interaction between n-BG and the polymer matrix. The Young's modulus of PLA/PMMA/n-BG decreases by 34 and 80%, indicating more flexible behavior compared to neat PLA. The PLA/PMMA/n-BG scaffolds showed a bioactive property related to the presence of hydroxyapatite crystals in the fiber surface after 28 days of immersion in a Simulated Body Fluids solution (SBF). In addition, the hydrolytic degradation process of PLA/PMMA/n-BG, analyzed after 35 days of immersion in a phosphate-buffered saline solution (PBS), was less than that of the pure PLA. The in vitro analysis using an HBOF-1.19 cell line indicated that the PLA/PMMA/n-BG scaffold showed good cell viability and was able to promote cell proliferation after 7 days. On the other hand, the in vivo biocompatibility evaluated via a subdermal model in BALC male mice corroborated the good behavior of the scaffolds in avoiding the generation of a cytotoxic effect and being able to enhance the healing process, suggesting that the materials are suitable for potential applications in tissue engineering.

Recent Developments on Cationic Polymerization of Vinyl Ethers

In recent times, the evolution of cationic polymerization has taken a multidirectional approach, with the development of cationic reversible addition-fragmentation chain transfer (RAFT) polymerization. In contrast to the conventional cationic polymerization methods, which were typically carried out under inert atmospheres and low temperatures, various novel polymerization techniques have been developed where the reactions are carried out in open air, operate at room temperature, are cost-effective, and are environmentally friendly. Besides, several external stimuli, such as heat, light, chemicals, electrical potential, etc. have been employed to activate and control the polymerization process. It also enables the combination of cationic polymerization with other polymerization methods in a single reaction vessel, eliminating the necessity for isolation and purification during intermediate steps. In addition, significant advancements have been made through various modifications in catalyst systems, resulting in polymers with an exceptionally high level of stereoregularity. This review article comprehensively analyses the recent developments in cationic polymerization, encompassing their applications and offering insights into future perspectives.

Bilateral Acrylic Hip Mold Arthroplasty in a Child With a Revision 60 years After Implantation: Clinical Case and Chemical Analysis of Endoprosthetic Material

A 68-year-old man was referred due to bilateral hip pain and gradual deterioration of walking. He had mold arthroplasties on both hips at the age of 7 years and has been functioning well for more than 5 decades. However, the original data on operative report and the prostheses were missing. The radiological examination revealed bilateral broken prosthetic material. Thus, stage bilateral revision total hip arthroplasty was performed. A detailed chemical analysis of retrieved mold arthroplasty implants proved that the acrylic material was noted to be the same composition with the difference in appearance likely being related to different thermal treatments originally applied to the implants. As presented in our clinical case, even obsolete implants may have good survivorship. According to the case presented, total hip arthroplasty could be considered an effective option with the desired functional outcome when conservative and joint-preserving measures are exhausted.

The Role of Life Stages in the Sensitivity of Hediste diversicolor to Nanoplastics: A Case Study with Poly(Methyl)Methacrylate (PMMA)

The presence of plastic particles in oceans has been recognized as a major environmental concern. The decrease in particle size increases their ability to directly interact with biota, with particles in the nanometer size range (nanoplastics-NPs) displaying a higher ability to penetrate biological membranes, which increases with the decrease in particle size. This study aimed to evaluate the role of life stages in the effects of poly(methyl)methacrylate (PMMA) NPs on the polychaete Hediste diversicolor, a key species in the marine food web and nutrient cycle. Thus, behavioral (burrowing activity in clean and spiked sediment) and biochemical endpoints (neurotransmission, energy reserves, antioxidant defenses, and oxidative damage) were assessed in juvenile and adult organisms after 10 days of exposure to spiked sediment (between 0.5 and 128 mg PMMA NPs/Kg sediment). Overall, the results show that H. diversicolor is sensitive to the presence of PMMA NPs. In juveniles, exposed organisms took longer to burrow in sediment, with significant differences from the controls being observed at all tested concentrations when the test was performed with clean sediment, whereas in PMMA NP-spiked sediment, effects were only found at the concentrations 8, 32, and 128 mg PMMA NPs/Kg sediment. Adults displayed lower sensitivity, with differences to controls being found, for both sediment types, at 8, 32, and 128 mg PMMA NPs/Kg sediment. In terms of Acetylcholinesterase, used as a marker of effects on neurotransmission, juveniles and adults displayed opposite trends, with exposed juveniles displaying increased activity (suggesting apoptosis), whereas in adults, overall decreased activity was found. Energy-related parameters revealed a generally similar pattern (increase in exposed organisms) and higher sensitivity in juveniles (significant effects even at the lower concentrations). NPs also demonstrated the ability to increase antioxidant defenses (higher in juveniles), with oxidative damage only being found in terms of protein carbonylation (all tested NPs conditions) in juveniles. Overall, the data reveal the potential of PMMA NPs to affect behavior and induce toxic effects in H. diversicolor, with greater effects in juveniles.

Microplastics and plastisphere at surface waters in the Southwestern Caribbean sea

Pollution generated by plastic waste has brought an environmental problem characterized by the omnipresence of smaller pieces of this material known as microplastics (MP). This issue was addresses by collecting samples with 250 μm pore size nets in two marine-coastal sectors of Southwestern Caribbean Sea during two contrasting seasons. Higher concentrations were found in rainy season than in dry season, reaching respectively 1.72 MP/m3 and 0.22 MP/m3. Within each sector, there were differences caused firstly by localities of higher concentrations of semi-closed water bodies localities during rainy season (Ciénaga Grande de Santa Marta and La Caimanera marsh), and secondly by lower concentrations of localities with less influenced of flow rates during dry season (Salamanca and Isla Fuerte). Moreover, the lowest concentration in dry season corresponding to La Caimanera marsh reflects how the community environmental management might decrease MP pollution. In both sectors and seasons, the particles of 0.3 mm (0.3-1.4 mm) size class dominated over those of 1.4 mm (1.4-5.0 mm) (reaching each respectively 1.33 MP/m3 and 0.39 MP/m3), with a dominance of fibers, except in the rainy season in Magdalena, where they were films. Using the FTIR technique, polypropylene was identified as the most abundant polymer in both sectors. The composition of the assemblage of microorganisms attached to microplastics presented higher richness and differed from that of free-living planktonic microbes. The most abundant members of the plastisphere were proteobacteria whose major representation was the pathogenic genus Vibrio, while the cyanobacteria dominated in seawater samples.

Ultrasound-Sensitive Intelligent Nanosystems: A Promising Strategy for the Treatment of Neurological Diseases

Neurological diseases are a major global health challenge, affecting hundreds of millions of people worldwide. Ultrasound therapy plays an irreplaceable role in the treatment of neurological diseases due to its noninvasive, highly focused, and strong tissue penetration capabilities. However, the complexity of brain and nervous system and the safety risks associated with prolonged exposure to ultrasound therapy severely limit the applicability of ultrasound therapy. Ultrasound-sensitive intelligent nanosystems (USINs) are a novel therapeutic strategy for neurological diseases that bring greater spatiotemporal controllability and improve safety to overcome these challenges. This review provides a detailed overview of therapeutic strategies and clinical advances of ultrasound in neurological diseases, focusing on the potential of USINs-based ultrasound in the treatment of neurological diseases. Based on the physical and chemical effects induced by ultrasound, rational design of USINs is a prerequisite for improving the efficacy of ultrasound therapy. Recent developments of ultrasound-sensitive nanocarriers and nanoagents are systemically reviewed. Finally, the challenges and developing prospects of USINs are discussed in depth, with a view to providing useful insights and guidance for efficient ultrasound treatment of neurological diseases.

Controlling glass forming kinetics in 2D perovskites using organic cation isomers

The recent discovery of glass-forming metal halide perovskites (MHPs) provides opportunities to broaden the application domain beyond traditionally celebrated optoelectronic research fueled by associated crystalline counterparts. In this regard, it is crucial to diversify the compositional space of glass-forming MHPs and introduce varied crystallization kinetics via synthetic structural engineering. Here, we compare two MHPs with slightly varying structural attributes, utilizing isomer organic cations with the same elemental composition, and demonstrate how this change in functional group position impacts the kinetics of glass formation and subsequent crystallization by multiple orders of magnitude. (S)-(-)-1-(1-Naphthyl)ethylammonium lead bromide (S(1-1)NPB) exhibits a lower melting point (Tm) of 175 °C and the melt readily vitrifies under a critical cooling rate (CCR) of 0.3 °C s-1. In contrast, (S)-(-)-1-(2-naphthyl)ethylammonium lead bromide (S(1-2)NPB) displays a Tm ∼193 °C and requires a CCR of 2500 °C s-1, necessitating the use of ultrafast calorimetry for glass formation and study of the underlying kinetics. The distinct Tm and glass-formation kinetics of the isomer MHPs are further understood through a combination of calorimetric and single-crystal X-ray diffraction studies on their crystalline counterparts, highlighting the influence of altered organic-inorganic hydrogen bonding interactions and entropic changes around melting, providing insights into the factors driving their divergent behaviors.

TiO2-MoS2-PMMA Nanocomposites for an Efficient Water Remediation

An improvement of water supply and sanitation and better management of water resources, especially in terms of water reuse, is one of the priorities of the European Green Deal. In this context, it is crucial to find new strategies to recycle wastewater efficiently in a low-cost and eco-friendly manner. The immobilization of inorganic nanomaterials on polymeric matrices has been drawing a lot of attention in recent years due to the extraordinary properties characterizing the as-obtained nanocomposites. The hybrid materials, indeed, combine the properties of the polymers, such as flexibility, low cost, mechanical stability, high durability, and ease of availability, with the properties of the inorganic counterpart. In particular, if the inorganic fillers are nanostructured photocatalysts, the materials will be able to utilize the energy delivered by light to catalyze chemical reactions for efficient wastewater treatment. Additionally, with the anchoring of the nanomaterials to the polymers, the dispersion of the nanomaterials in the environment is prevented, thus overcoming one of the main limits that impede the application of nanostructured photocatalysts on a large scale. In this work, we will present nanocomposites made of polymers, i.e., polymethyl methacrylate (PMMA), and photocatalytic semiconductors, i.e., TiO2 nanoparticles (Evonik). MoS2 nanoflakes were also added as co-catalysts to improve the photocatalytic performance of the TiO2. The hybrid materials were prepared using the sonication and solution casting method. The nanocomposites were deeply characterized, and their remarkable photocatalytic abilities were evaluated by the degradation of two common water pollutants: methyl orange and diclofenac. The relevance of the obtained results will be discussed, opening the route for the application of these materials in photocatalysis and especially for novel wastewater remediation.

Plastic pollution in Moreton Bay sediments, Southeast Queensland, Australia

The mounting issue of plastic waste in the aquatic ecosystem is a growing source of concern. Most plastic waste originates on land and a significant proportion of this eventually finds its way into the marine environment, which is widely regarded as a major repository for plastic debris. Currently, there exists a substantial gap in our understanding of how much plastic, the main polymer types, and the distribution of plastic in the marine environment. This study aimed to provide information on mass concentrations of a range of plastics in the surface sediments in the semi-enclosed Moreton Bay, just offshore the large city of Brisbane, Southeast Queensland, Australia. Surface sediment samples were quantitatively analysed for a suite of 7 common plastic polymer types (i.e., polystyrene (PS), polycarbonate (PC), poly-(methyl methacrylate) (PMMA), polypropylene (PP), polyethylene terephthalate (PET), polyethylene (PE) and polyvinyl chloride (PVC)) using a pressurized liquid extraction (PLE) followed by double-shot microfurnace pyrolysis coupled to gas chromatography mass spectrometry (Pyr-GC/MS). The advantage of this approach is that it can measure plastics below the limit of visual detection. The study revealed that Σ7plastics were consistently present in the samples, although the concentrations displayed a wide range of concentrations from 3.3 to 2194.2 μg/g across different sites. Among the polymers analysed, PE and PVC were found at the highest concentrations, ranging from 2.3 to 1885.9 μg/g and 3.0-979.5 μg/g, respectively. Based on the average concentrations of plastics measured, the dry bulk density and volume of sediments within the top 10 cm of the bay, it was estimated that there is a minimum of 7000 t of plastics stored in the surface sediments of the bay. This study is the first to report the mass concentrations of identified plastics and identify the main polymer types in Moreton Bay. This is important information to develop management plans to reduce the plastic waste entering the coastal marine environment.

Facile Synthesis of Poly(methyl methacrylate) Silica Nanocomposite Monolith by In Situ Free Radical Polymerization of Methyl Methacrylate in the Presence of Functionalized Silica Nanoparticles

Novel porous poly(methyl methacrylate) (PMMA) silica nanocomposites have been produced by utilization of polymerization-induced phase separation in a simple one-pot approach. A facile free radical polymerization of MMA in the presence of surface methacrylate-functionalized silica nanoparticles was carried out in ethanol-based solvents, successfully producing novel, morphologically designable porous nanocomposite monoliths. Differing from standard free radical polymerization in solution, a mixture of good and poor solvents (ethanol/N,N-dimethylformamide ratio) for the resulting polymer was used to trigger spinodal phase separation. The influence of monomer concentration, as well as solvent composition, on the morphology of the resulting porous polymers has been investigated. Porous monolith structures composed of connected particles and co-continuous morphologies were observed under a scanning electron microscope depending on the polymerization conditions. The resulting polymers were insoluble and showed swelling characteristics in some organic solvents that are capable of dissolving regular PMMA, indicating covalent bonds between the functionalized silica nanoparticles and the polymer chains. The presence of silica particles in the final polymer was proven via an ATR-IR analysis. The glass transition temperature of the present PMMA-silica nanocomposite was higher than that of the conventional PMMA. The porous polymer immersed in a mixed organic solvent showed coloration induced by the Christiansen effect.

Effect of methyl methacrylate concentrations on surface and thermal analysis of composite polymer polymethylmethacrylates with mesogen reactive RM82

This research report of the synthesis of composite polymers from liquid crystal mesogen reactive (RM82) monomers with Methyl methacrylate (MMA). The purpose of this research is analysis the effect concentration of MMA on the surface and thermal of the composite polymer PMMA-RM82. The result of the morphological analysis of composite surfaces performed by polarization optical microscopy (POM) technique showed liquid crystal textures affected composition from two monomers. SEM images show that the surface of the RM82 liquid crystal has a shape resembling fibrous and blade-like crystals with a length of up to 10 μm (micrometers). Analysis thermal showed the heat released by the PMMA-RM82 increased with the increase in MMA weight percent. This affects the rapid crystallization process of PMMA-RM82 which of concentration MMA 30%-RM82 the heat released is almost twice as much as the heat released by MMA 5%-RM82. The absence of PMMA and RM82 peaks both endothermic and exothermic in PMMA-RM82 samples indicates that polymerization has occurred and a new product has formed. Analysis structure molecule by FTIR found that the IR spectral form of each variation in the weight percent of MMA was almost the same, but there was a spectral shift that showed that polymerization had occurred in PMMA-RM82 which was characterized by a reaction to the free radical C=C bond released by the photoinitiator. XRD pattern of composite PMMA-RM82 showed the peaks formed are located at scattering angles similar to RM82 but there is a decrease in intensity as the percent weight of MMA increases.

Correlation between the Chemical Structure of (Meth)Acrylic Monomers and the Properties of Powder Clear Coatings Based on the Polyacrylate Resins

This paper presents studies on the influence of the chemical structure of (meth)acrylic monomers on the properties of powder coatings based on polyacrylate resins. For this purpose, a wide range of monomers were selected-2-hydroxyethyl methacrylate (HEMA), methyl methacrylate (MMA), n-butyl acrylate (nBA), tert-butyl acrylate (tBA), dodecyl acrylate (DA), ethyl acrylate (EA) and benzyl acrylate (BAZ)-for the synthesis of the polyacrylate resin. The average molecular mass and molecular mass distribution of the synthesized resins were measured by gel permeation chromatography (GPC). The glass transition temperature (Tg) and viscosity of polyacrylate resins were determined by using differential scanning calorimetry (DSC) and a Brookfield viscometer. These parameters were necessary to obtain information about storage stability and behavior during the application of powder clear coatings. Additionally, DSC was also used to checked the course of the low-temperature curing reaction between the hydroxyl group contained in the polyacrylate resin and the blocked polyisocyanate group derived from a commercial agent such as Vestanat B 1358/100. The properties of the cured powder clear coatings were tested, such as: roughness, gloss, adhesion to the steel surface, hardness, cupping, scratch resistance, impact resistance and water contact angle. The best powder clear coating based on the polyacrylate resin L_HEMA/6MMA/0.5nBA/0.5DA was characterized as having good scratch resistance (550 g) and adhesion to the steel surface, a high water contact angle (93.53 deg.) and excellent cupping (13.38 mm). Moreover, its crosslinking density (CD) and its thermal stability was checked by using dynamic mechanical analysis (DMA) and thermogravimetric analysis (TGA).

Preparation and thermal responsiveness of microencapsulated fluorinated liquids for automatic fire extinguishing

Most early-stage fires originating in small confined spaces may not be effectively mitigated by automatic fire-extinguishing systems. Leveraging the unique controlled release capability and barrier properties of microcapsules presents a promising avenue for developing multifunctional and intelligent fire-extinguishing agents tailored for early-stage fire suppression. This paper introduces two types of microcapsules that integrate automatic detection and fire extinguishing functions, utilizing fluorinated liquids specifically perfluoro(2-methyl-3-pentanone) and 1,1,1,2,2,3,4,5,5,5 decafluoro-3-methoxy-4(trifluoromethyl)-pentane as core materials. The preparation process was optimized, and the thermal response of the microcapsules was evaluated by directly incorporating them into combustible materials. The results indicated a correlation between the preparation method, coating efficiency, and thermal stability of microcapsules with the core-wall materials. When the fluoride solution in the core material reaches the thermal response threshold temperature, the gas pressure generated during vaporization and phase change can break through the shell, enabling early active fire protection. Beyond a specific threshold of additive microcapsules in the material, the material exhibits self-extinguishing potential during combustion. In cases where the additive amount falls short of achieving self-extinguishing, the fire-resistant performance of materials can be enhanced through various measures. For instance, reducing the amount of fire-extinguishing agents, delaying the ignition time of fuel, and lowering the heat release rate during combustion are effective strategies. Moreover, the degree of improvement is related to the additional amount and the type of core-wall materials. The thermal-response mechanism of microcapsules constitutes a comprehensive mechanism with physical and chemical effects. The finding of this research offer a new technical approach for microencapsulating high-boiling-point gas extinguishing agents, facilitating intelligent and precise prevention of early fires resulting from combustible materials.

Reusable graphite-based electrochemical sensors for L-dopa and dopamine detection

A fully reusable electrochemical device is proposed for the first time made from laser cutting and a homemade conductive ink composed of carbon and nail polish. As a sensor substrate, we applied polymethyl methacrylate, which allows the surface to be renewed by simply removing and reapplying a new layer of ink. In addition to the ease of renewing the sensor's conductive surface, the design of the device has allowed for the integration of different forms of analysis. The determination of L-Dopa was performed using DPV, which presented a linear response range between 5.0 and 1000.0 μmol L-1, and a LOD of 0.11 μmol L-1. For dopamine, a flow injection analysis system was employed, and using the amperometric technique measurements were performed with a linear ranging from 2.0 to 100.0 μmol L-1 and a LOD of 0.26 μmol L-1. To demonstrate its applicability, the device was used in the quantification of analytes in pharmaceutical drug and synthetic urine samples.

Progress of Polymer Electrolytes Worked in Solid-State Lithium Batteries for Wide-Temperature Application

Solid-state Li-ion batteries have emerged as the most promising next-generation energy storage systems, offering theoretical advantages such as superior safety and higher energy density. However, polymer-based solid-state Li-ion batteries face challenges across wide temperature ranges. The primary issue lies in the fact that most polymer electrolytes exhibit relatively low ionic conductivity at or below room temperature. This sensitivity to temperature variations poses challenges in operating solid-state lithium batteries at sub-zero temperatures. Moreover, elevated working temperatures lead to polymer shrinkage and deformation, ultimately resulting in battery failure. To address this challenge of polymer-based solid-state batteries, this review presents an overview of various promising polymer electrolyte systems. The review provides insights into the temperature-dependent physical and electrochemical properties of polymers, aiming to expand the temperature range of operation. The review also further summarizes modification strategies for polymer electrolytes suited to diverse temperatures. The final section summarizes the performance of various polymer-based solid-state batteries at different temperatures. Valuable insights and potential future research directions for designing wide-temperature polymer electrolytes are presented based on the differences in battery performance. This information is intended to inspire practical applications of wide-temperature polymer-based solid-state batteries.

Bulk Depolymerization of Methacrylate Polymers via Pendent Group Activation

In this study, we present an efficient approach for the depolymerization of poly(methyl methacrylate) (PMMA) copolymers synthesized via conventional radical polymerization. By incorporating low mol % phthalimide ester-containing monomers during the polymerization process, colorless and transparent polymers closely resembling unfunctionalized PMMA are obtained, which can achieve >95% reversion to methyl methacrylate (MMA). Notably, our catalyst-free bulk depolymerization method exhibits exceptional efficiency, even for high-molecular-weight polymers, including ultrahigh-molecular-weight (106-107 g/mol) PMMA, where near-quantitative depolymerization is achieved. Moreover, this approach yields polymer byproducts of significantly lower molecular weight, distinguishing it from bulk depolymerization methods initiated from chain ends. Furthermore, we extend our investigation to polymethacrylate networks, demonstrating high extents of depolymerization. This innovative depolymerization strategy offers promising opportunities for the development of sustainable polymethacrylate materials, holding great potential for various applications in polymer science.

Identification of a potent palladium-aryldiphosphine catalytic system for high-performance carbonylation of alkenes

The development of stable and efficient ligands is of vital significance to enhance the catalytic performance of carbonylation reactions of alkenes. Herein, an aryldiphosphine ligand (L11) bearing the [Ph2P(ortho-C6H4)]2CH2 skeleton is reported for palladium-catalyzed regioselective carbonylation of alkenes. Compared with the industrially successful Pd/1,2-bis(di-tert-butylphosphinomethyl)benzene catalyst, catalytic efficiency catalyzed by Pd/L11 on methoxycarbonylation of ethylene is obtained, exhibiting better catalytic performance (TON: >2,390,000; TOF: 100,000 h-1; selectivity: >99%) and stronger oxygen-resistance stability. Moreover, a substrate compatibility (122 examples) including chiral and bioactive alkenes or alcohols is achieved with up to 99% yield and 99% regioselectivity. Experimental and computational investigations show that the appropriate bite angle of aryldiphosphine ligand and the favorable interaction of 1,4-dioxane with Pd/L11 synergistically contribute to high activity and selectivity while the electron deficient phosphines originated from electron delocalization endow L11 with excellent oxygen-resistance stability.

PMMA bone cement with L-arginine/nano fish bone nanocomplex for apatite formation

Bone cement is one of the materials used in orthopaedics that serves various functions, such as binding bone implants, replacing damaged bones and filling spaces within bones. Various materials have been used to synthesize bone cement, and one promising material for further research is fish bone waste-based bone cement. This study investigates the potential of fish bone waste-based bone cement by incorporating nano fish bone (NFB) and L-arginine (L-Arg) protein into polymethyl methacrylate (PMMA) to examine apatite growth. NFB derived from the Salmo salar fish positively influences osteoblast cell proliferation and differentiation, while L-Arg enhances biocompatibility and antibiotic properties. The NFB/L-Arg combination holds promise in accelerating new bone formation and cell growth, both of which are crucial for fracture healing and bone remodelling. Tensile strength tests reveal the superior performance of BC-PMMA-1-NFB/L-Arg (36.11 MPa) compared with commercial PMMA (32 MPa). Immersion tests with simulated body fluid (SBF) solution for 7 days reveal accelerated apatite layer formation, emphasizing the potential benefits of NFB/L-Arg in bone cement applications.

Biodegradable reactive compatibilizers for efficient in-situ compatibilization of poly (lactic acid)/poly (butylene adipate-terephthalate) blends

The wide application of fully biodegradable polylactic acid/polybutylene terephthalate (PLA/PBAT) blends in environmentally friendly packaging were limited because of poor compatibility. Normal compatibilizers suffer from poor thermal stability and non-biodegradability. In this work, epoxy copolymer (MDOG) with different molecular structures were made of 2-methylene-1, 3-dioxoheptane, and glycidyl methacrylate as raw materials by free radical copolymerization. MDOG copolymers have good biodegradability and a high thermal decomposition temperature of 361 °C. The chemical reaction of the epoxy groups in MDOG with PLA and PBAT during the melting reaction improved the interfacial bonding by decreasing the particle size of PBAT. Compared to the PLA/PBAT blends, the tensile strength and fracture toughness of PLA/PBAT/MDOG blends were enhanced to 34.6 MPa and 115.8 MJ/m3, which are 25 % and 81 % higher, respectively. As a result, this work offers new methods for developing thermally stable and biodegradable compatibilizers, which will hopefully promote the development of packaging industry.

Quantification and characterization of microplastics in coastal environments: Insights from laser direct infrared imaging

The study identified and quantified nine plastic polymers frequently detected in the environment by collecting sediment and seawater samples from coastal areas in Auckland, New Zealand. Polymer types, size distributions, and number of microplastics (MPs) were analyzed using a laser direct infrared (LDIR) imaging technique. Compared to conventional spectroscopic or microscopic methods, LDIR enabled capturing and quantifying MPs in much lower size ranges (20-5000 μm). The results demonstrated the widespread occurrence of MPs in the Auckland coastal environment, with polyethylene terephthalate (PET) being the most frequently detected plastic polymer. MP contamination levels ranged from 13 to 83 particles per liter of coastal water and from 1200 to 3400 particles/kg of dry sand in beach sediments. Six additional locations were investigated to assess the contribution of MPs from stormwater drains to the coastal environment. The total count of identified MPs extracted from sediments near stormwater drains reached a maximum of 18,000 particles/kg of dry sand, representing an order of magnitude increase compared to MP levels found in beach sediments at the same location. In contrast to the prevalence of PET and polyamide observed in beach sediments and coastal waters, polyurethane and polyethylene emerged as the predominant plastic polymers in the vicinity of stormwater drain sediments, implying that the variation could potentially stem from distinct sources of plastics. This significant disparity in quality and quantity underscored the potential link between urban runoff and MP pollution in marine ecosystems. A sample preparation method using 100 g sediment samples was developed and used to assess and compare MPs detection in sediment samples. The commonly used 5 g sample method showed higher extraction efficiency and better detection of the most abundant MPs, but the new 100 g method enabled the detection of previously missed, less abundant plastics.

Creation of Polymer Datasets with Targeted Backbones for Screening of High-Performance Membranes for Gas Separation

A simple approach was developed to computationally construct a polymer dataset by combining simplified molecular-input line-entry system (SMILES) strings of a targeted polymer backbone and a variety of molecular fragments. This method was used to create 14 polymer datasets by combining seven polymer backbones and molecules from two large molecular datasets (MOSES and QM9). Polymer backbones that were studied include four polydimethylsiloxane (PDMS) based backbones, poly(ethylene oxide) (PEO), poly(allyl glycidyl ether) (PAGE), and polyphosphazene (PPZ). The generated polymer datasets can be used for various cheminformatics tasks, including high-throughput screening for gas permeability and selectivity. This study utilized machine learning (ML) models to screen the polymers for CO2/CH4 and CO2/N2 gas separation using membranes. Several polymers of interest were identified. The results highlight that employing an ML model fitted to polymer selectivities leads to higher accuracy in predicting polymer selectivity compared to using the ratio of predicted permeabilities.

Progress in Fabrication and Applications of Cholesteric Liquid Crystal Microcapsules

Liquid crystals (LCs) are well known for inherent responsiveness to external stimuli, such as light, thermal, magnetic, and electric fields. Cholesteric LCs are among the most fascinating, since they possess distinctive optical properties due to the helical molecular orientation. However, the good flow, easy contamination, and poor stability of small-molecule LCs limit their further applications, and microencapsulation as one of the most effective tools can evade these disadvantages. Microencapsulation can offer shell-core structure with LCs in the core can strengthen their stability, avoiding interference with the environment while maintaining the stimuli-responsiveness and optical properties. Here, we report recent progress in the fabrication and applications of cholesteric LC microcapsules (CLCMCs). We summarize general properties and basic principles, fabrication methods including interfacial polymerization, in-situ polymerization, complex coacervation, solvent evaporation, microfluidic and polymerization of reactive mesogens, and then give a comprehensive overview of their applications in various popular domains, including smart fabrics, smart sensor, smart displays, anti-counterfeiting, information encryption, biomedicine and actuators. Finally, we discuss the currently facing challenges and the potential development directions in this field.

Highly sensitive ammonia sensor based on a PMMA/PANI microwire structure

In this paper, a highly sensitive ammonia (N H 3) sensor based on a polymethyl methacrylate/polyaniline (PMMA/PANI) microwire structure is designed and implemented. First, a micron-sized PMMA microwire was fabricated and connected with two tapered single-mode fibers to form a coupling structure; thus, the Mach-Zehnder (MZ) interference was successfully excited due to the good light conductivity of the PMMA. It was demonstrated that the coupling structure behaved with a high refractive index detection sensitivity of 3044 nm/RIU. To make it sensitive to N H 3, the PANI was selected to mix with PMMA and then formed a micron-level PMMA/PANI fiber. The experimental results showed that the PMMA/PANI fiber can selectively sense N H 3 with a high sensitivity of 65.3 pm/ppm. This proposed N H 3 sensor not only solves the problem of sensitive film shedding, but also possesses the advantages of good integration, high sensitivity, good selectivity, and short response time.

Surfactant-free microemulsions (SFMEs) as a template for porous polymer synthesis

HYPOTHESIS

Surfactant-free microemulsions (SFMEs) were recently reported to be an interesting medium for free-radical polymerizations. The aim of this study is to investigate the link between the morphology of PMMA monopolymers as well as PMMA-PHEMA-copolymers with the expected nature of the SFME before polymerization. A surfactant-based microemulsion with nonionic surfactants was investigated as a reference system. It is expected that the kind of mesostructuring of the SFME (oil-in-water-like, bicontinuous, inverse) corresponds with the latter polymer morphology, just like it is the case in surfactant-based systems.

EXPERIMENTS

Simple SFME systems composed of water, a hydrotrope (isopropanol or tert-butyl alcohol), and methyl methacrylate (MMA) as polymerizable oil as well as the more complex system comprising 2-hydroxyethyl methacrylate (HEMA) as an additional amphiphilic co-monomer, were investigated. A surfactant-based system using a mixture of Tergitol 15-S-12 and Synperonic A11-LQ-(TH) as surfactants, water, and MMA in the presence and absence of HEMA as polymerizable co-surfactant was investigated as a reference system. Structural analysis was done by recording (pseudo-)ternary phase diagrams, dynamic light scattering (DLS), and conductivity measurements. Polymerizations were performed using the oil-soluble initiator PEROXAN BCC at 318 K for 24 h with adjacent lyophilization. The morphology of dried polymers was determined by light microscopy, scanning electron microscopy, and BET adsorption isotherms.

FINDINGS

Porous polymers of different morphologies (from coagulations of droplet-like aggregates to sponge-like ones) in the size range of 200 nm up to some µm can be derived from previously mesostructured, surfactant-free mixtures. Previously unstructured, oil-rich regions lead to solid, transparent polymers without nanostructured morphologies. The surfactant-based reference system comprises remarkably similar phase behavior before polymerizations and similar polymer morphologies as the comparable surfactant-free system. This leads to the assumption that the hydrotropic behavior of HEMA and its interplay with MMA and water is the structure-giving factor in this system.

Electrospun Tamarindus indica-loaded antimicrobial PMMA/cellulose acetate/PEO nanofibrous scaffolds for accelerated wound healing: In-vitro and in-vivo assessments

In this work, Tamarindus indica (T. indica)-loaded crosslinked poly(methyl methacrylate) (PMMA)/cellulose acetate (CA)/poly(ethylene oxide) (PEO) electrospun nanofibers were designed and fabricated for wound healing applications. T. indica is a plant extract that possesses antidiabetic, antimicrobial, antioxidant, antimalarial and wound healing properties. T. indica leaves extract of different concentrations were blended with a tuned composition of a matrix comprised of PMMA (10 %), CA (2 %) and PEO (1.5 %), and were electrospun to form smooth, dense and continuous nanofibers as illustrated by SEM investigation. In vitro evaluation of T. indica-loaded nanofibers on normal human skin fibroblasts (HBF4) revealed a high compatibility and low cytotoxicity. T. indica-loaded nanofibers significantly increased the healing activity of scratched HBF4 cells, as compared to the free plant extract, and the healing activity was significantly enhanced upon increasing the plant extract concentration. Moreover, T. indica-loaded nanofibers demonstrated significant antimicrobial activity in vitro against the tested microbes. In vivo, nanofibers resulted in a superior wound healing efficiency compared to the control untreated animals. Hence, engineered nanofibers loaded with potent phytochemicals could be exploited as an effective biocompatible and eco-friendly antimicrobial biomaterials and wound healing composites.

Spinal fusion of biodegradable poly(propylene fumarate) and poly(propylene fumarate-co-caprolactone) copolymers in rabbits

Background

Autologous bone grafts are currently the standard in orthopedic surgery despite limited donor sources and the prevalence of donor site morbidity. Other alternatives such as allografts are more readily available than autografts but have lower rates of graft incorporation.

Methods

Here, we propose a novel graft alternative consisting of an injectable poly(propylene fumarate) (PPF) and poly(propylene fumarate-co-caprolactone) P(PF-co-CL) copolymer with a recombinant human bone morphogenetic protein-2 (rhBMP-2)/vascular epithelial growth factor (VEGF) release system accompanied by hydroxyapatite (HA). The efficacy of scaffold formulations was studied using a standard, bilateral, L-level (L5-L6) posterolateral transverse spinal fusion using New Zealand white rabbits. Rabbits were divided into 4 experimental groups: group I, negative control; group II, autograft (positive control); group III, injectable PPF scaffold with rhBMP-2/VEGF release system and HA; group IV, injectable P(PF-co-CL)scaffold with rhBMP-2/VEGF release system and HA. Spines were harvested at 6 weeks and 12 weeks after surgery, and spinal fusions were assessed using manual palpation, radiographic analysis, micro-computed tomography (μCT) assessment, and histologic analysis.

Results

Of the 4 experimental groups, the injectable P(PF-co-CL) scaffold displayed superior initial strength and faster degradation than scaffolds constructed from PPF alone and facilitated the fusion of lateral processes in the rabbit standard posterolateral spinal fusion model. The results obtained from manual palpation, radiology, and μCT showed no difference between the P(PF-co-CL) group and the PPF group. However, histologic sections showed more osteogenesis with the new injectable P(PF-co-CL) scaffold.

Conclusion

Injectable P(PF-co-CL) polymers showed promising spine fusion abilities in rabbits after 12 weeks of posterolateral implantation.

Poly(methyl methacrylate) in Orthopedics: Strategies, Challenges, and Prospects in Bone Tissue Engineering

Poly(methyl methacrylate) (PMMA) is widely used in orthopedic applications, including bone cement in total joint replacement surgery, bone fillers, and bone substitutes due to its affordability, biocompatibility, and processability. However, the bone regeneration efficiency of PMMA is limited because of its lack of bioactivity, poor osseointegration, and non-degradability. The use of bone cement also has disadvantages such as methyl methacrylate (MMA) release and high exothermic temperature during the polymerization of PMMA, which can cause thermal necrosis. To address these problems, various strategies have been adopted, such as surface modification techniques and the incorporation of various bioactive agents and biopolymers into PMMA. In this review, the physicochemical properties and synthesis methods of PMMA are discussed, with a special focus on the utilization of various PMMA composites in bone tissue engineering. Additionally, the challenges involved in incorporating PMMA into regenerative medicine are discussed with suitable research findings with the intention of providing insightful advice to support its successful clinical applications.

Fabrication, structural, and enhanced mechanical behavior of MgO substituted PMMA composites for dental applications

The most common denture material used for dentistry is poly-methyl-methacrylate (PMMA). Usually, the polymeric PMMA material has numerous biological, mechanical and cost-effective shortcomings. Hence, to resolve such types of drawbacks, attempts have been made to investigate fillers of the PMMA like alumina (Al2O3), silica (SiO2), zirconia (ZrO2) etc. For the enhancement of the PMMA properties a suitable additive is required for its orthopedic applications. Herein, the main motive of this study was to synthesize a magnesium oxide (MgO) reinforced polymer-based hybrid nano-composites by using heat cure method with superior optical, biological and mechanical characteristics. For the structural and vibrational studies of the composites, XRD and FT-IR were carried out. Herein, the percentage of crystallinity for all the fabricated composites were also calculated and found to be 14.79-30.31. Various physical and optical parameters such as density, band gap, Urbach energy, cutoff energy, cutoff wavelength, steepness parameter, electron-phonon interaction, refractive index, and optical dielectric constant were also studied and their values are found to be in the range of 1.21-1.394 g/cm3, 5.44-5.48 eV, 0.167-0.027 eV, 5.68 eV, 218 nm, 0.156-0.962, 4.273-0.693, 1.937-1.932, and 3.752-3.731 respectively. To evaluate the mechanical properties like compressive strength, flexural strength, and fracture toughness of the composites a Universal Testing Machine (UTM) was used and their values were 60.3 and 101 MPa, 78 and 40.3 MPa, 5.85 and 9.8 MPa-m1/2 respectively. Tribological tests of the composites were also carried out. In order to check the toxicity, MTT assay was also carried out for the PM0 and PM15 [(x)MgO + (100 - x) (C5O2H8)n] (x = 0 and 15) composites. This study provides a comprehensive insight into the structural, physical, optical, and biological features of the fabricated PMMA-MgO composites, highlighting the potential of the PM15 composite with its enhanced density, mechanical strength, and excellent biocompatibility for denture applications.

Enhancing the optical properties of [P(MMA-co-AN)/ZrO2]TF by doping fluorescein dye, TD-DFT/DMOl3 simulations and COVID-19 main protease docking

Poly methyl methacrylate-co-acrylonitrile [P(MMA-co-AN)]HB hybrid blend was first synthesized by precipitation polymerization and characterized by static light scattering. With a thickness of 200 ± 5 nm, the hybrid nanocomposite of [P(MMA-co-AN)/ZrO2]HNC thin films were fabricated by spin coating method. X-Ray diffraction studies showed a monoclinic cell structure with an average crystalline size of 180 nm for the fabricated films. An improvement in the optical properties were figured out when fluorescein dye was doped in the hybrid nanocomposite. Where the optical energy gap was decreased from 4.31 to 4.025 eV for fluorescein doped hybrid nanocomposite. While a possible energy transfer between ZrO2 and fluorescein was investigated in the laser photoluminescence spectra. DFT-CASTEP simulations were deployed to calculate the theoretical optical properties for the molecules under consideration. The structural and optical simulations of [P(MMA-co-AN)/ZrO2]HNC were found to match the experimental data. Molecular docking studies of [P(MMA-co-AN)/ZrO2]Iso against the main protease of novel corona virus COVID 19 (PDB code 6LU7 Hormone) showed an interesting interaction.

The spatial distribution and physico-chemical characteristic of microplastics in the sediment and cockle (Anadara granosa) from the coastal waters of East Java, Indonesia, and the health hazards associated with cockle consumption

This study evaluated microplastic (MP) abundances and physico-chemical characteristics in sediments and Anadara granosa along the East Java coast and their health implications. Fibers (74 %) dominated sediment MPs at south coast, while fragments (49-61 %) dominated north coast. Fiber (43-52 %) is the predominant MP in cockle tissues in all locations. Most MP in sediments (31-47 %) and cockle tissues (41-49 %) is black. The majority of microplastics (100-1500 μm) are found in sediment (73-90 %), and cockles (77-79 %). Very weak correlations found between the amount of MP and the length of the cockle shell. However, Spearman correlation shows that as the amount of MP in sediment increases, so does the amount of MP in cockle tissue. Each year, individuals of varying ages consume an average of 20,800 to 156,000 MP items. Cockles contain plasticizer components and microplastic polymers which are classified from II to V regarding of hazard levels, with V being the most hazardous.

Novel Life Prediction Method of PMMA for Cultural Relics Protection Based on the BP Neural Network

Poly(methyl methacrylate) (PMMA) is widely used in the preservation and exhibition of cultural relics in museums. Accurately predicting its service life can help avoid many negative effects caused by PMMA aging. To study the change in the yellowing index of PMMA after aging in a UV light environment, an aging experiment was conducted. A prediction model for the service life of PMMA was established using nonlinear curve fitting and a back propagation (BP) neural network. By comparing the goodness of fit, simulation and modeling capabilities of the initial data, and the predictive ability for new data, it was found that the BP neural network prediction model outperformed the nonlinear curve fitting prediction model. In this study, the service life of newly produced PMMA samples was calculated as 7.83, 8.47, and 8.42 years, based on the yellowing index of retired PMMA as a benchmark and using the output data from the BP neural network prediction model. At this time, the performance and exhibition effect of the PMMA are poor, and the batch of PMMA needs to be updated.

Polymeric materials for ultrasound imaging and therapy

Ultrasound (US) is routinely used for diagnostic imaging and increasingly employed for therapeutic applications. Materials that act as cavitation nuclei can improve the resolution of US imaging, and facilitate therapeutic US procedures by promoting local drug delivery or allowing temporary biological barrier opening at moderate acoustic powers. Polymeric materials offer a high degree of control over physicochemical features concerning responsiveness to US, e.g. via tuning chain composition, length and rigidity. This level of control cannot be achieved by materials made of lipids or proteins. In this perspective, we present key engineered polymeric materials that respond to US, including microbubbles, gas-stabilizing nanocups, microcapsules and gas-releasing nanoparticles, and discuss their formulation aspects as well as their principles of US responsiveness. Focusing on microbubbles as the most common US-responsive polymeric materials, we further evaluate the available chemical toolbox to engineer polymer shell properties and enhance their performance in US imaging and US-mediated drug delivery. Additionally, we summarize emerging applications of polymeric microbubbles in molecular imaging, sonopermeation, and gas and drug delivery, based on refinement of MB shell properties. Altogether, this manuscript provides new perspectives on US-responsive polymeric designs, envisaging their current and future applications in US imaging and therapy.

Critical review on modified floating photocatalysts for emerging contaminants removal from landscape water: problems, methods and mechanism

Due to the disorderly discharge in modern production and daily life of people, emerging contaminants(ECs) began to appear in landscape water, and have become a key public concern. Because of the unique characteristics of landscape water, it is difficult to efficiently remove ECs either by natural purification or by traditional large-scale sewage treatment facilities. The ideal purification method is to remove them while maintaining a beautiful environment. Possessing the feature of low-density, floating photocatalysts could harvest sufficient light on the surface of the water for photocatalytic degradation, which may be an important supplement for ECs treatment in landscape water. This paper gave a review related to floating photocatalysts and proposed an idea of combining floating photocatalysts to construct bionic photocatalytic materials for contaminative landscape water treatment. Six types of common floating substrates and corresponding applications for floating photocatalysts were concluded in this paper, and the main problem leading to the low efficiency of photocatalysts and three corresponding three improvement strategies were discussed. Besides, the modification mechanisms of photocatalysts were discussed thoroughly. On this basis, the engineering application prospects of bionic photocatalytic materials were proposed to remove ECs in landscape water.

Progress in Nanostructured Mechano-Bactericidal Polymeric Surfaces for Biomedical Applications

Bacterial infections and antibiotic resistance remain significant contributors to morbidity and mortality worldwide. Despite recent advances in biomedical research, a substantial number of medical devices and implants continue to be plagued by bacterial colonisation, resulting in severe consequences, including fatalities. The development of nanostructured surfaces with mechano-bactericidal properties has emerged as a promising solution to this problem. These surfaces employ a mechanical rupturing mechanism to lyse bacterial cells, effectively halting subsequent biofilm formation on various materials and, ultimately, thwarting bacterial infections. This review delves into the prevailing research progress within the realm of nanostructured mechano-bactericidal polymeric surfaces. It also investigates the diverse fabrication methods for developing nanostructured polymeric surfaces with mechano-bactericidal properties. We then discuss the significant challenges associated with each approach and identify research gaps that warrant exploration in future studies, emphasizing the potential for polymeric implants to leverage their distinct physical, chemical, and mechanical properties over traditional materials like metals.

Direct deep UV lithography to micropattern PMMA for stem cell culture

Microengineering is increasingly being used for controlling the microenvironment of stem cells. Here, a novel method for fabricating structures with subcellular dimensions in commonly available thermoplastic poly(methyl methacrylate) (PMMA) is shown. Microstructures are produced in PMMA substrates using Deep Ultraviolet lithography, and the effect of different developers is described. Microgrooves fabricated in PMMA are used for the neuronal differentiation of mouse embryonic stem cells (mESCs) directly on the polymer. The fabrication of 3D, curvilinear patterned surfaces is also highlighted. A 3D multilayered microfluidic chip is fabricated using this method, which includes a porous polycarbonate (PC) membrane as cell culture substrate. Besides directly manufacturing PMMA-based microfluidic devices, an application of the novel approach is shown where a reusable PMMA master is created for replicating microstructures with polydimethylsiloxane (PDMS). As an application example, microchannels fabricated in PDMS are used to selectively expose mESCs to soluble factors in a localized manner. The described microfabrication process offers a remarkably simple method to fabricate for example multifunctional topographical or microfluidic culture substrates outside cleanrooms, thereby using inexpensive and widely accessible equipment. The versatility of the underlying process could find various applications also in optical systems and surface modification of biomedical implants.

A Coherent Assessment of the Compressive Strain Rate Response of PC, PETG, PMMA, and TPU Thermoplastics in MEX Additive Manufacturing

In this study, we successfully address a significant research and engineering gap by quantitatively assessing the impact of varying compressive loading rates on the mechanical behavior of four popular thermoplastic polymers in material-extrusion-based (MEX) 3D printing. Raw powders of polycarbonate (PC), polyethylene terephthalate glycol (PETG), polymethyl methacrylate (PMMA), and thermoplastic polyurethane (TPU) were processed through melt extrusion, and the filaments were used to 3D-print the test samples. For completeness, thermogravimetric analysis and a compressive test following the ASTM-D695 standard were conducted. Ultimately, the compressive strength and yield stress, the compressive modulus of elasticity and toughness, and the maximum compressive sensitivity index were thoroughly documented. Specimens were tested in strain rates from 1.3 mm/min to 200 mm/min. The compressive strength (40% for the PMMA) and stiffness (29% for the TPU) increased with the increase in the strain rate in all polymers tested. PC had the highest strain rate sensitivity. Significant variations in deformation and fracture modes were observed and thoroughly documented throughout this study. Our findings can be useful in industrial engineering as valued design optimization input parameters in various applications involving the above-mentioned polymeric materials.

Colorimetric Multigas Sensor Arrays and an Artificial Olfactory Platform for Volatile Organic Compounds

Herein, we develop colorimetric multigas sensor arrays assembling chemo-reactive fluorescent patch arrays and 10 × 10 indium gallium zinc oxide phototransistor arrays and apply them to an artificial olfactory platform to recognize five different volatile organic compounds (VOCs). Porous nanofibers, coupled with two organic emitters and emitting fluorescence, rapidly respond to gas-phased VOCs and offer unique fluorescent patterns associated with particular gas conditions, including gas kinds, concentrations, and exposure times by forming patch arrays with different fluorophore component ratios. These VOC-induced fluorescent patterns could be quantified and amplified by indium gallium zinc oxide (IGZO) phototransistor arrays functioning as a signal-generating component, resulting in gas-fingerprint patterns regarding electrical signals. Thus, the pattern library associated with VOCs and their concentration enables us to determine each airborne analyte as the artificial olfactory platform. Therefore, this system could achieve rapid, early quantitative recognition of hazardous gases and be applied as a preventative, portable, and wearable multigas identifier in various fields.

Bis(thienyl)ethenes with α-methoxymethyl groups. Syntheses, spectroscopic Hammett plots, and stabilities in PMMA films

A series of bis(thienyl)ethenes (BTEs) possessing perfluorocyclopentene backbones and methoxymethyl groups (MOM) in the 2/2'-positions of the thiophenes was prepared and examined. The substitution pattern of the 5/5'-positions was varied, covering the range from electron-donating to electron-withdrawing. The substituent effects of the absorption wavelengths of the ring-opened and the ring-closed isomers, which are interconverted by reversible 6π-electrocyclizations and cycloreversions, are studied by means of the spectroscopic Hammett equation and the Hammett-Brown equation. Excellent correlations of these linear free energy relationships were found, when the σp values of the Hammett equation, which summarize inductive, mesomeric and field effects, were replaced to the Hammett-Brown σp+ and σp- values which also take direct conjugation into account. We studied solvent effects on the spectroscopic properties and embedded the BTEs into polymethylmethacrylate (PMMA) coatings to examine their fatigue resistance. By our studies, the spectroscopic properties of BTEs can be adjusted by variation of the substitution pattern to a desired excitation wavelength for switching processes.

An effective device to enable consistent scratches for in vitro scratch assays

BACKGROUND

The in-vitro scratch assay is a useful method in wound healing research to assess cell migration. In this assay, a scratch is created in a confluent cell layer by mechanically removing cells through manual scraping with a sharp-edged tool. This step is traditionally done with pipette tips and is unsuitable for high-throughput assays, as the created scratches are highly variable in width and position. Commercially available solutions are often expensive, and require specific cultureware which might not be suitable for all studies.

RESULTS

In this study, we have developed a flexible cell scratch device comprising a single wounding tool, a guide and an imaging template for consistent and reproducible scratch assays in 96-well plates. Our results showed that the device produced a more consistent scratch profile compared to the conventional method of using pipette tips. The imaging template also allowed operators to easily locate and image the same region of interest at different time points, which potentially could be used for other assays.

CONCLUSIONS

Our flexible yet effective scratch device thus enables robust scratch assays that can be applied to different experimental needs, providing researchers with an easy and reliable tool for their studies.

Advanced Injection Molding Methods: Review

Injection molding is a method commonly used to manufacture plastic products. This technology makes it possible to obtain products of specially designed shape and size. In addition, the developed mold allows for repeated and repeatable production of selected plastic parts. Over the years, this technology grew in importance, and nowadays, products produced by injection molding are used in almost every field of industry. This paper is a review and provides information on recent research reports in the field of modern injection molding techniques. Selected plastics most commonly processed by this technique are discussed. Next, the chosen types of this technique are presented, along with a discussion of the parameters that affect performance and process flow. Depending on the proposed method, the influence of various factors on the quality and yield of the obtained products was analyzed. Nowadays, the link between these two properties is extremely important. The work presented in the article refers to research aimed at modifying injection molding methods enabling high product quality with high productivity at the same time. An important role is also played by lowering production costs and reducing the negative impact on the environment. The review discusses modern injection molding technologies, the development of which is constantly progressing. Finally, the impact of the technology on the ecological environment is discussed and the perspectives of the process were presented.

Different Polymers for the Base of Removable Dentures? Part I: A Narrative Review of Mechanical and Physical Properties

Even before considering their introduction into the mouth, the choice of materials for the optimization of the prosthesis depends on specific parameters such as their biocompatibility, solidity, resistance, and longevity. In the first part of this two-part review, we approach the various mechanical characteristics that affect this choice, which are closely related to the manufacturing process. Among the materials currently available, it is mainly polymers that are suitable for this use in this field. Historically, the most widely used polymer has been polymethyl methacrylate (PMMA), but more recently, polyamides (nylon) and polyether ether ketone (PEEK) have provided interesting advantages. The incorporation of certain molecules into these polymers will lead to modifications aimed at improving the mechanical properties of the prosthetic bases. In the second part of the review, the safety aspects of prostheses in the oral ecosystem (fragility of the undercuts of soft/hard tissues, neutral pH of saliva, and stability of the microbiota) are addressed. The microbial colonization of the prosthesis, in relation to the composition of the material used and its surface conditions (roughness, hydrophilicity), is of primary importance. Whatever the material and manufacturing process chosen, the coating or finishes dependent on the surface condition remain essential (polishing, non-stick coating) for limiting microbial colonization. The objective of this narrative review is to compile an inventory of the mechanical and physical properties as well as the clinical conditions likely to guide the choice between polymers for the base of removable prostheses.

Multicomponent Acrylic Formulation Design for Corrosion Casting with Controlled Mechanical Properties

Corrosion casting based on the curing of acrylic resins enables one to create casts as replicas of body systems, enhancing our knowledge of veterinary medicine. The identification of the optimal chemical formulations as well as the processing conditions, the delivery of good control during the liquid state and the excellent macroscopic properties during solidification and after use are remaining challenges. In the present work, based on the identification of more qualitative trends, it is demonstrated that multicomponent comonomer mixtures are interesting materials that can be used to expand the range of mechanical properties and can specifically result in a better balance between stiffness and flexibility while guaranteeing dimensional stability. Emphasis is put on a large pool of formulations in the testing phase to then perform a detailed mechanical flexural analysis for the most promising cases during a more rigorous testing phase, accounting for a new pragmatic protocol for the pot life. This protocol consists of a vial-based turning test and a measurement of the viscosity variation up to 1000 mPa∙s and highlights the complex interplay between the overall initial concentrations and the impact of the absence of mixing once the system is at rest. It is demonstrated that the use of only low-molar-mass crosslinkers should be avoided, and overall, an intermediate amount of crosslinkers is recommendable.

Improving the Mechanical Properties of Orthodontic Occlusal Splints Using Nanoparticles: Silver and Zinc Oxide

The goal of the current study was to determine the mechanical proprieties of polymethylmethacrylate (PMMA) and the improved compound, the graphene-based PMMA, with Zn and Ag and to compare the results. Scanning electron microscopy analysis of the samples before and after the mechanical test was conducted. The compression behavior, flexural properties, tensile strength, and shape of the samples were all investigated and compared between the variants of PMMA. Commercially available polymethylmethacrylate was used (Orthocryl^®-Dentaurum, Ispringen, Germany) with the salt and pepper technique according to the manufacturer's instructions to produce 20 samples for each mechanical trial with standard cylinders (4 mm diameter × 8 mm length) for compression, parallelepipedal prisms for flexing (2 mm × 2 mm × 25 mm) and flat samples for traction. There was no statistical difference in the mechanical proprieties of the samples evaluated, although there were values that could suggest significance. The graphene-based PMMA demonstrated good mechanical proprieties, like the commercially available PMMA, and appears promising for future clinical use based on its multiple advantages.

Pendant Modification of Poly(methyl methacrylate) to Enhance Its Stability against Photoirradiation

Photostabilization of functional polymeric materials is important for protection against aging and ultraviolet (UV) irradiation. There is, therefore, the impetus to modify polymers to increase their resistance to photodegradation and photooxidation on extended exposure to UV light in harsh conditions. Various polymeric additives have been designed and synthesized in recent years, and their potential as photostabilizers has been explored. Reported here is the effect of pendant functionalization of poly(methyl methacrylate) (PMMA) through organometallic moiety incorporation into the polymer's backbone. The reaction of PMMA with ethylenediamine leads to the formation of an amino residue that can react with salicylaldehyde to produce the corresponding Schiff base. Adding metal chlorides (zinc, copper, nickel, and cobalt) led to the formation of organometallic residues on the polymeric chains. Thin films of modified and unmodified PMMA were produced and irradiated with UV light to determine the effect of pendant modification on photostability. The photostabilization of PMMA was assessed using a range of methods, including infrared spectroscopy, weight loss, decomposition rate constant, and surface morphology. The modified PMMA incorporating organic Schiff base metal complexes showed less photodecomposition than the unmodified polymer or one containing the Schiff base only. Thus, the metals significantly reduced the photodegradation of polymeric materials. The polymer containing the Schiff base-cobalt unit showed the least damage in the PMMA surface due to photoirradiation, followed by those containing nickel, zinc, and copper, in that order.

Degradation of Polymethylmethacrylate (PMMA) Bioreactors Used for Algal Cultivation

This paper depicts characteristics of degradation of walls of bioreactors made of polymethylmethacrylate (PMMA) which was used to culture algae. The degradation processes take place stimulated by lighting of external surface and interaction with cultured species on internal surface. Results presented are representative for degradation of a bioreactor tube after the 4-year cultivation of Chlorella sp. Microscopic observations, roughness and transmission tests showed that changes have occurred on the inner surface. The result of use is a decrease in transmission and an increase in roughness. Microscopic observations showed that particles remained after culture, especially in cracks.