Biochemical Behavior, Influence on Cell DNA Condition, and Microbiological Properties of Wool and Wool-Copper Materials

The paper presents the study concerning the preparation and physio-chemical and biological properties of wool-copper (WO-Cu) materials obtained by the sputter deposition of copper onto the wool fibers. The WO-Cu material was subjected to physio-chemical and biological investigations. The physio-chemical investigations included the elemental analysis of materials (C, N, O, S, and Cu), their microscopic analysis, and surface properties analysis (specific surface area and total pore volume). The biological investigations consisted of the antimicrobial activity tests of the WO-Cu materials against colonies of Gram-positive (Staphylococcus aureus) bacteria, Gram-negative (Escherichia coli) bacteria, and fungal mold species (Chaetomium globosum). Biochemical-hematological tests included the evaluation of the activated partial thromboplastin time and pro-thrombin time. The tested wool-copper demonstrated the ability to interact with the DNA in a time-dependent manner. These interactions led to the DNA's breaking and degradation. The antimicrobial and antifungal activities of the WO-Cu materials suggest a potential application as an antibacterial/antifungal material. Wool-copper materials may be also used as customized materials where the blood coagulation process could be well controlled through the appropriate copper content.

Electrospun polylactic acid nanofibers membrane with copper ion-loaded clay nanotubes for fresh-keeping packaging

The plastics derived from fossil fuels for food packaging results in serious environmental problems. Developing environment-friendly materials for food packaging is urgent and essential. In this study, polylactic acid (PLA) composite nanofibers membranes were prepared with good biocompatibility and antibacterial property. Cu2+ loaded in the natural halloysite nanotubes (HNTs) was used for the antibacterial agent. Cu2+ was loaded in the HNTs and was confirmed by the X-ray photoelectron spectroscopy (XPS). PLA nanofibers with different HNTs-Cu content were continuous nanofibers with the nanoscale range. HNTs-Cu entered into the nanofiber successfully. Thermal analysis results showed composite nanofibers had good thermal stability. Composite nanofiber membranes had the good hydrophobic property. HNTs-Cu improved the mechanical property of composite nanofibers than pure PLA nanofibers. Tensile strength and elasticity modulus of composite nanofibers with 4 % HNTs-Cu content were the most outstanding. L929 cells were cultured on the nanofiber membranes for biocompatibility evaluation. Cell viability of nanofiber membranes was above the 90 %. Cell live/dead staining results showed L929 cells was seldom dead on the nanofiber membranes. PLA/HNTs-Cu nanofiber membranes exhibited excellent antibacterial effects on S. aureus and E. coli. The inhibitory rates against S. aureus and E. coli were 98.31 % and 97.80 % respectively. The fresh-keeping effects of nanofiber membranes were evaluated by the strawberry preservation. Strawberries covered by nanofiber membranes exhibited better appearance, lower weight loss and higher firmness than control, PLA and PLA/HNTs groups. It promised that PLA/HNTs-Cu composite nanofiber membranes have the significant potential application for active food packaging.

Advances in amelioration of plasma electrolytic oxidation coatings on biodegradable magnesium and alloys

Magnesium and its alloys are considered excellent materials for biodegradable implants because of their good biocompatibility and biodegradability as well as their mechanical properties. However, the rapid degradation rate severely limits their clinical applications. Plasma electrolytic oxidation (PEO), also known as micro-arc oxidation (MAO), is an effective surface modification technique. However, there are many pores and cracks on the coating surface under conventional PEO process. The corrosive products tend to penetrate deeply into the substrate, reducing its corrosion resistance and the biocompatibility, which makes PEO-coated Mg difficult to meet the long-term needs of in vivo implants. Hence, it is necessary to modify the PEO coating. This review discusses the formation mechanism and the influential parameters of PEO coatings on Mg. This is followed by a review of the latest research of the pretreatment and typical amelioration of PEO coating on biodegradable Mg alloys in the past 5 years, including calcium phosphate (Ca-P) coating, layered double hydroxide (LDH)-PEO coating, ZrO2 incorporated-PEO coating, antibacterial ingredients-PEO coating, drug-PEO coating, polymer-PEO composite coating, Plasma electrolytic fluorination (PEF) coating and self-healing coating. Meanwhile, the improvements of morphology, corrosion resistance, wear resistance, biocompatibility, antibacterial abilities, and drug loading abilities and the preparation methods of the modified PEO coatings are deeply discussed as well. Finally, the challenges and prospects of PEO coatings are discussed in detail for the purpose of promoting the clinical application of biodegradable Mg alloys.

Cable Bacteria Skeletons as Catalytically Active Electrodes

Cable bacteria are multicellular, filamentous bacteria that use internal conductive fibers to transfer electrons over centimeter distances from donors within anoxic sediment layers to oxygen at the surface. We extracted the fibers and used them as free-standing bio-based electrodes to investigate their electrocatalytic behavior. The fibers catalyzed the reversible interconversion of oxygen and water, and an electric current was running through the fibers even when the potential difference was generated solely by a gradient of oxygen concentration. Oxygen reduction as well as oxygen evolution were confirmed by optical measurements. Within living cable bacteria, oxygen reduction by direct electrocatalysis on the fibers and not by membrane-bound proteins readily explains exceptionally high cell-specific oxygen consumption rates observed in the oxic zone, while electrocatalytic water oxidation may provide oxygen to cells in the anoxic zone.

pH-Responsive nanoplatform synergistic gas/photothermal therapy to eliminate biofilms in poly(L-lactic acid) scaffolds

To date, implant-associated infection is still a significant clinical challenge, which cannot be effectively eliminated by single therapies due to the formation of microbial biofilms. Herein, a pH-responsive nanoplatform was constructed via the in situ growth of zinc sulfide (ZnS) nanoparticles on the surface of Ti3C2 MXene nanosheets, which was subsequently introduced in poly(L-lactic acid) (PLLA) to prepare a composite bone scaffold via selective laser sintering technology. In the acidic biofilm microenvironment, the degradation of ZnS released hydrogen sulfide (H2S) gas to eliminate the biofilm extracellular DNA (eDNA), thus destroying the compactness of the biofilm. Then, the bacterial biofilm became sensitive to hyperthermia, which could be further destroyed under near-infrared light irradiation due to the excellent photothermal property of MXene, finally achieving gas/photothermal synergistic antibiofilm and efficient sterilization. The results showed that the synergistic gas/photothermal therapy for the composite scaffold not only evidently inhibited the formation of biofilms, but also effectively eradicated the eDNA of the already-formed biofilms and killed 90.4% of E. coli and 84.2% of S. aureus under near infrared light irradiation compared with single gas or photothermal therapy. In addition, the composite scaffold promoted the proliferation and osteogenic differentiation of mouse bone marrow mesenchymal stem cells. Thus, the designed scaffold with excellent biofilm elimination and osteogenesis ability has great potential as an alternative treatment for implant-associated bone infections.

The Effect of Doping on the Electrical and Dielectric Properties of Hydroxyapatite for Medical Applications: From Powders to Thin Films

Recently, the favorable electrical properties of biomaterials have been acknowledged as crucial for various medical applications, including both bone healing and growth processes. This review will specifically concentrate on calcium phosphate (CaP)-based bioceramics, with a notable emphasis on hydroxyapatite (HA), among the diverse range of synthetic biomaterials. HA is currently the subject of extensive research in the medical field, particularly in dentistry and orthopedics. The existing literature encompasses numerous studies exploring the physical-chemical, mechanical, and biological properties of HA-based materials produced in various forms (i.e., powders, pellets, and/or thin films) using various physical and chemical vapor deposition techniques. In comparison, there is a relative scarcity of research on the electrical and dielectric properties of HA, which have been demonstrated to be essential for understanding dipole polarization and surface charge. It is noteworthy that these electrical and dielectric properties also offer valuable insights into the structure and functioning of biological tissues and cells. In this respect, electrical impedance studies on living tissues have been performed to assess the condition of cell membranes and estimate cell shape and size. The need to fill the gap and correlate the physical-chemical, mechanical, and biological characteristics with the electrical and dielectric properties could represent a step forward in providing new avenues for the development of the next-generation of high-performance HA-doped biomaterials for future top medical applications. Therefore, this review focuses on the electrical and dielectric properties of HA-based biomaterials, covering a range from powders and pellets to thin films, with a particular emphasis on the impact of the various dopants used. Therefore, it will be revealed that each dopant possesses unique properties capable of enhancing the overall characteristics of the produced structures. Considering that the electrical and dielectric properties of HA-based biomaterials have not been extensively explored thus far, the aim of this review is to compile and thoroughly discuss the latest research findings in the field, with special attention given to biomedical applications.

Recent advances in copper sulfide nanoparticles for phototherapy of bacterial infections and cancer

Copper sulfide nanoparticles (CuS NPs) have attracted growing interest in biomedical research due to their remarkable properties, such as their high photothermal and thermodynamic capabilities, which are ideal for anticancer and antibacterial applications. This comprehensive review focuses on the current state of antitumor and antibacterial applications of CuS NPs. The initial section provides an overview of the various approaches to synthesizing CuS NPs, highlighting the size, shape and composition of CuS NPs fabricated using different methods. In this review, the mechanisms underlying the antitumor and antibacterial activities of CuS NPs in medical applications are discussed and the clinical challenges associated with the use of CuS NPs are also addressed.

Copper infused fabric attenuates inflammation in macrophages

While inflammation is an important immune response for protection from infections, excessive or prolonged inflammation can lead to a variety of debilitating diseases including skin disease, diabetes, heart disease, stroke, autoimmune diseases and cancer. Inflammation is a graded response that is typically initiated when resident macrophages sense the presence of pathogens or damage in the tissue and produce inflammatory cytokines and chemokines to kill the pathogen, clear debris and dead tissue, and initiate tissue repair. Here we show that copper-infused fabrics can prevent inflammation by blocking the production of inflammatory cytokines from macrophages after being exposed to LPS, a component of bacterial cell wall. Mechanistically, we show that copper-infused fabrics can significantly reduce the NF-κB and IRF3 activation in LPS-stimulated macrophages. Given the importance of excessive inflammation in diabetes, we show that copper can reduce insulin resistance mediated by inflammatory cytokines in muscle cells. Our data show that copper infused fabrics may be useful to reduce excessive inflammation in macrophages and improve insulin sensitivity in skeletal muscles.

Toxicity Mechanisms of Copper Nanoparticles and Copper Surfaces on Bacterial Cells and Viruses

Copper is a metal historically used to prevent infections. One of the most relevant challenges in modern society are infectious disease outbreaks, where copper-based technologies can play a significant role. Currently, copper nanoparticles and surfaces are the most common antimicrobial copper-based technologies. Despite the widespread use of copper on nanoparticles and surfaces, the toxicity mechanism(s) explaining their unique antimicrobial properties are not entirely known. In general, toxicity effects described in bacteria and fungi involve the rupture of membranes, accumulation of ions inside the cell, protein inactivation, and DNA damage. A few studies have associated Cu-toxicity with ROS production and genetic material degradation in viruses. Therefore, understanding the mechanisms of the toxicity of copper nanoparticles and surfaces will contribute to developing and implementing efficient antimicrobial technologies to combat old and new infectious agents that can lead to disease outbreaks such as COVID-19. This review summarizes the current knowledge regarding the microbial toxicity of copper nanoparticles and surfaces and the gaps in this knowledge. In addition, we discuss potential applications derived from discovering new elements of copper toxicity, such as using different molecules or modifications to potentiate toxicity or antimicrobial specificity.

Inhibition of microbial extracellular electron transfer corrosion of marine structural steel with multiple alloy elements

The microbial corrosion of marine structural steels (09CrCuSb low alloy steel (LAS) and Q235 carbon steel (CS)) in Desulfovibrio vulgaris medium and Pseudomonas aeruginosa medium based on seawater was investigated. In the D. vulgaris medium, the weight loss and maximum pit depth of 09CrCuSb LAS were 0.59 and 0.56 times as much as those of Q235 CS, respectively. Meanwhile, in the P. aeruginosa medium, the values were 0.53 and 0.67 times, respectively. Compared to Q235 CS, 09CrCuSb LAS contains more alloy elements (Cr, Ni, Cu, Al and Sb), which led to obvious inhibition of sessile bacteria growth but had no effect on planktonic bacteria. The number of live sessile cells on the 09CrCuSb LAS surface was 23.4 % and 26.9 % of that on the Q235 CS surface in the D. vulgaris medium and P. aeruginosa medium, respectively. Fewer sessile cells on the steel surface led to a lower extracellular electron transfer (EET) rate so that less corrosion occurred. In addition, the combined effect of alloying elements on grain refinement and passive film formation also improved the anti-corrosion property of the steels.

Performance evaluation of an electrostatic precipitator with a copper plate using an aerosolized SARS-CoV-2 surrogate (bacteriophage phi 6)

The global spread of severe acute respiratory syndrome coronavirus-2 (SARS-CoV-2) has reminded us of the importance of developing technologies to reduce and control bioaerosols in built environments. For bioaerosol control, the interaction between researchers and biomaterials is essential, and considering the characteristics of target pathogens is strongly required. Herein, we used enveloped viral aerosols, bacteriophage phi 6, for evaluating the performance of an electrostatic precipitator (ESP) with a copper-collecting plate (Cu-plate). In particular, bacteriophage phi 6 is an accessible enveloped virus that can be operated in biosafety level (BSL)-1 as a promising surrogate for SARS-CoV-2 with structural and morphological similarities. ESP with Cu-plate showed >91% of particle removal efficiency for viral aerosols at 77 cm/s of airflow face velocity. Moreover, the Cu-plate presented a potent antiviral performance of 5.4-relative log reduction within <15 min of contact. We believe that the evaluation of ESP performance using an aerosolized enveloped virus and plaque assay is invaluable. Our results provide essential information for the development of bioaerosol control technologies that will lead the post-corona era.

How Effective are Metal Nanotherapeutic Platforms Against Bacterial Infections? A Comprehensive Review of Literature

The emergence of multidrug-resistant bacteria has been deemed a global crisis that affects humans worldwide. Novel anti-infection strategies are desperately needed because of the limitations of conventional antibiotics. However, the increasing gap between clinical demand and antimicrobial treatment innovation, as well as the membrane permeability obstacle especially in gram-negative bacteria fearfully restrict the reformation of antibacterial strategy. Metal-organic frameworks (MOFs) have the advantages of adjustable apertures, high drug-loading rates, tailorable structures, and superior biocompatibilities, enabling their utilization as drug delivery carriers in biotherapy applications. Additionally, the metal elements in MOFs are usually bactericidal. This article provides a review of the state-of-The-art design, the underlying antibacterial mechanisms and antibacterial applications of MOF- and MOF-based drug-loading materials. In addition, the existing problems and future perspectives of MOF- and MOF-based drug-loading materials are also discussed.

Electrochemical Synthesis of Nanocrystalline CuAg Coatings on Stainless Steel from Cyanide-Free Electrolyte

Herein we demonstrate a novel plating bath, free from cyanide, to plate a highly adherent nanocrystalline copper-silver (ncCuAg) coating on a stainless-steel substrate and its application as an antimicrobial coating. The microstructures, such as the grain size, texture, microstrain, and the crystalline preferential orientation of CuAg deposits, are systematically investigated by X-ray diffraction analysis. The range of 13.4–16.6 nm was discovered to be the crystallite size determined from the X-ray peak broadening (Scherrer’s formula). Both HRTEM, FESEM-EDS, XPS, and mapping analysis revealed that the ncCuAg coatings are composed of both Ag and Cu atoms. Electrochemical processes occurring during CuAg co-deposition were investigated by using linear sweep voltammetry (LSV), cyclic voltammetry (CV), and anodic linear stripping voltammetry (ALSV). Additionally, the coatings made of ncCuAg produced by these baths work well as antibacterial agents against gram-positive (Staphylococcus) and gram-negative bacteria (Escherichia coli).

Recent Advances in Copper and Copper-Derived Materials for Antimicrobial Resistance and Infection Control

Antibacterial properties of copper have been known for ages. With the rise of antimicrobial resistance (AMR), hospital-acquired infections, and the current SARS-CoV-2 pandemic, copper and copper-derived materials are being widely researched for healthcare ranging from therapeutics to advanced wound dressing to medical devices. We cover current research that highlights the potential uses of metallic and ionic copper, copper alloys, copper nanostructures, and copper composites as antibacterial, antifungal, and antiviral agents, including those against the SARS-CoV-2 virus. The applications of copper-enabled engineered materials in medical devices, wound dressings, personal protective equipment, and self-cleaning surfaces are discussed. We emphasize the potential of copper and copper-derived materials in combating AMR and efficiently reducing infections in clinical settings.

Copper-containing nanoparticles: Mechanism of antimicrobial effect and application in dentistry-a narrative review

Copper has been used as an antimicrobial agent long time ago. Nowadays, copper-containing nanoparticles (NPs) with antimicrobial properties have been widely used in all aspects of our daily life. Copper-containing NPs may also be incorporated or coated on the surface of dental materials to inhibit oral pathogenic microorganisms. This review aims to detail copper-containing NPs' antimicrobial mechanism, cytotoxic effect and their application in dentistry.

One-step Green Fabrication of Antimicrobial Surfaces via In Situ Growth of Copper Oxide Nanoparticles

Microorganisms such as pathogenic bacteria, fungi, and viruses pose a serious threat to human health and society. Surfaces are one of the major pathways for the transmission of infectious diseases. Therefore, imparting antipathogenic properties to these surfaces is significant. Here, we present a rapid, one-step approach for practical fabrication of antimicrobial and antifungal surfaces using an eco-friendly and low-cost reducing agent, the extract of Cedrus libani. Copper oxide nanoparticles were grown in situ on the surface of print paper and fabric in the presence of the copper salt and extract, without the use of any additional chemicals. The morphology and composition of the grown nanoparticles were characterized using field emission scanning electron microscopy, energy-dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy, and X-ray diffraction techniques. The analysis revealed that the grown particles consist of mainly spherical CuO nanoparticles with an average size of ∼14 nm and its clusters with an average size of ∼700 nm. The in situ growth process enables strong bonding of the nanoparticles to the surface, resulting in enhanced durability against wear and tear. Moreover, the fabricated surface shows excellent growth inhibition ability and bactericidal activity against both gram-negative and gram-positive bacteria, Escherichia coli and Staphylococcus aureus, as well as antifungal activity against Candida albicans, a common pathogenic fungus. The ability to grow copper oxide nanoparticles on different surfaces paves the way for a range of applications in wound dressings, masks, and protective medical equipment.

Enhanced anti-microbial activity and osseointegration of Ta/Cu co-implanted polyetheretherketone

Polyetheretherketone (PEEK) has been widely applied for orthopedic and oral implants due to its excellent mechanical properties, biocompatibility, and radiolucency. However, its bioinert and the lack of anti-microbial activity limit its application. We modified the PEEK surface with Ta/Cu co-implantation using plasma immersion ion-implantation technology. After implantation of Ta/Cu ions, the morphology and roughness of the PEEK surface were not significantly changed at micron level. We estimated the cytocompatibility, anti-microbial ability, and osteogenic differentiation of rat bone mesenchymal stem cells (BMSCs) of the modified surfaces in vitro. Compared to the untreated surfaces, the Ta ion-treated surface showed improved adhesion, proliferation, ALP activity, ECM mineralization, and osteogenic gene expression of BMSCs. Further, the Cu ion-treated surface showed reduced initial adhesion and proliferation of Escherichia coli and Staphylococcus aureus in vitro and proliferation of Staphylococcus aureus in the mouse subcutaneous implant-associated infection model. According to a rat bone repair model, all Ta ion-implanted groups demonstrated improved new bone formation. In summary, Ta/Cu ion co-impanation improved anti-microbial activity and promoted osseointegration of the PEEK surface.

Antibacterial Activity of Electrospun Polyacrylonitrile Copper Nanoparticle Nanofibers on Antibiotic Resistant Pathogens and Methicillin Resistant Staphylococcus aureus (MRSA)

Bacteria induced diseases such as community-acquired pneumonia (CAP) are easily transmitted through respiratory droplets expelled from a person’s nose or mouth. It has become increasingly important for researchers to discover materials that can be implemented in in vitro surface contact settings which disrupt bacterial growth and transmission. Copper (Cu) is known to have antibacterial properties and have been used in medical applications. This study investigates the antibacterial properties of polyacrylonitrile (PAN) based nanofibers coated with different concentrations of copper nanoparticles (CuNPs). Different concentrations of copper sulfate (CuSO₄) and polyacrylonitrile (PAN) were mixed with dimethylformamide (DMF) solution, an electrospinning solvent that also acts as a reducing agent for CuSO₄, which forms CuNPs and Cu ions. The resulting colloidal solutions were electrospun into nanofibers, which were then characterized using various analysis techniques. Methicillin-Resistant isolates of Staphylococcus aureus, an infective strain that induces pneumonia, were incubated with cutouts of various nanocomposites using disk diffusion methods on Luria-Bertani (LB) agar to test for the polymers’ antibacterial properties. Herein, we disclose that PAN-CuNP nanofibers have successfully demonstrated antibacterial activity against bacteria that were otherwise resistant to highly effective antibiotics. Our findings reveal that PAN-CuNP nanofibers have the potential to be used on contact surfaces that are at risk of contracting bacterial infections, such as masks, in vivo implants, or surgical intubation.

Mechanical Alloying Integrated with Cold Spray Coating for Fabrication Cu50(Ti50-xNix),x ; 10, 20, 30, and 40 at.% Antibiofilm Metallic Glass Coated/SUS304 Sheets

Antibacterial agents derived from conventional organic compounds have traditionally been employed as a biofilm protective coating for many years. These agents, on the other hand, often include toxic components that are potentially hazardous to humans. Multiple approaches have been investigated over the last two decades, including the use of various metallic and oxide materials, in order to produce a diverse variety of usable coating layers. When it comes to material coating approaches, the cold spray technique, which is a solid-state method that works well with nanopowders, has shown superior performance. Its capacity to produce unique material coating in ways that are not possible with other thermal methods is the primary reason for its importance in contemporary production. The present work has been addressed in part to explore the possibility of employing mechanically alloyed Cu₅₀(Ti_50−xNi_x)_x; x = 10, 20, 30, and 40 at.% metallic glass powders, for producing an antibiofilm/SUS304 surface protective coating, using the cold spray approach. In this study, elemental Cu, Ti, and Ni powders were low-energy ball milled for 100 h to fabricate metallic glassy powders with different Ni contents. The as-prepared metallic glassy powders were utilized to coat SUS304 sheets, using the cold spraying process. With high nanohardness values, the as-fabricated coating material, in particular Cu₅₀Ti₂₀Ni_30, demonstrated remarkable performance in comparison to other materials in its class. Furthermore, it displayed excellent wear resistance while maintaining a low coefficient of friction, with values ranging from 0.32 to 0.45 in the tested range. E. coli biofilms were formed on 20 mm² SUS304 sheet coated coupons, which had been injected with 1.5 108 CFU mL⁻¹ of the bacterium. With the use of nanocrystalline Cu-based powders, it is feasible to achieve considerable biofilm inhibition, which is a practical strategy for accomplishing the suppression of biofilm formation.

Efficacy and Mechanisms of Copper Ion-Catalyzed Inactivation of Human Norovirus

The antinoroviral effect of copper ions is well known, yet most of this work has previously been conducted in copper and copper alloy surfaces, not copper ions in solution. In this work, we characterized the effects that Cu ions have on human norovirus capsids’ and surrogates’ integrity to explain empirical data, indicating virus inactivation by copper alloy surfaces, and as means of developing novel metal ion-based virucides. Comparatively high concentrations of Cu(II) ions (>10 mM) had little effect on the infectivity of human norovirus surrogates, so we used sodium ascorbate as a reducing agent to generate unstable Cu(I) ions from solutions of copper bromide. We found that significantly lower concentrations of monovalent copper ions (∼0.1 mM) compared to divalent copper ions cause capsid protein damage that prevents human norovirus capsids from binding to cell receptors in vitro and induce a greater than 4-log reduction in infectivity of Tulane virus, a human norovirus surrogate. Further, these Cu(I) solutions caused reduction of GII.4 norovirus from stool in suspension, producing about a 2-log reduction of virus as measured by a reverse transcriptase-quantitative polymerase chain reaction. Sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) data indicate substantial major capsid protein cleavage of both GI.7 and GII.4 norovirus capsids, and TEM images show the complete loss of capsid integrity of GI.7 norovirus. GII.4 virus-like particles (VLPs) were less susceptible to inactivation by copper ion treatments than GI.7 VLPs based upon receptor binding and SDS-PAGE analysis of viral capsids. The combined data demonstrate that stabilized Cu(I) ion solutions show promise as highly effective noroviral disinfectants in solution that can potentially be utilized at low concentrations for inactivation of human noroviruses.

Cobalamin cbiP mutant shows decreased tolerance to low temperature and copper stress in Listeria monocytogenes

Background

Listeria monocytogenes is a foodborne pathogen that causes listeriosis in humans. This pathogen activates multiple regulatory mechanisms in response to stress, and cobalamin biosynthesis might have a potential role in bacterial protection. Low temperature is a strategy used in the food industry to control bacteria proliferation; however, L. monocytogenes can grow in cold temperatures and overcome different stress conditions. In this study we selected L. monocytogenes List2-2, a strain with high tolerance to the combination of low temperature + copper, to understand whether the cobalamin biosynthesis pathway is part of the tolerance mechanism to this stress condition. For this, we characterized the transcription level of three cobalamin biosynthesis-related genes (cbiP, cbiB, and cysG) and the eutV gene, a transcriptional regulator encoding gene involved in ethanolamine metabolism, in L. monocytogenes strain List2-2 growing simultaneously under two environmental stressors: low temperature (8 °C) + copper (0.5 mM of CuSO₄ × 5H₂O). In addition, the gene cbiP, which encodes an essential cobyric acid synthase required in the cobalamin pathway, was deleted by homologous recombination to evaluate the impact of this gene in L. monocytogenes tolerance to a low temperature (8 °C) + different copper concentrations.

Results

By analyzing the KEGG pathway database, twenty-two genes were involved in the cobalamin biosynthesis pathway in L. monocytogenes List2-2. The expression of genes cbiP, cbiB, and cysG, and eutV increased 6 h after the exposure to low temperature + copper. The cobalamin cbiP mutant strain List2-2ΔcbiP showed less tolerance to low temperature + copper (3 mM) than the wild-type L. monocytogenes List2-2. The addition of cyanocobalamin (5 nM) to the medium reverted the phenotype observed in List2-2ΔcbiP.

Conclusion

These results indicate that cobalamin biosynthesis is necessary for L. monocytogenes growth under stress and that the cbiP gene may play a role in the survival and growth of L. monocytogenes List2-2 at low temperature + copper.

Supplementary Information

The online version contains supplementary material available at 10.1186/s40659-022-00376-4.

More Insights about the Efficacy of Copper Ion Treatment on Mycobacterium avium subsp. paratuberculosis (MAP): A Clue for the Observed Tolerance

Background: Scientific evidence is scarce for the antimicrobial effect of copper on bacteria characterized as more resistant. Using Mycobacterium avium subsp. paratuberculosis (MAP), a highly resistant microorganism, as a pathogen model, copper ion treatment has shown a significant bactericidal effect; however, the sustainability of MAP against copper toxicity was also reported in several studies. Accordingly, the present study aimed to evaluate the impacts of copper on MAP. Methodology: This study considered physicochemical properties and copper concentration in a buffer since it could modulate MAP response during the application of copper treatment. Results: Despite the efficacy of copper ions in significantly reducing the MAP load in Phosphate Buffered Saline, some MAP cells were able to survive. The copper concentration generated by the copper ion treatment device increased significantly with increasing exposure times. MAP bacterial load decreased significantly when treated with copper ions as the exposure times increased. An increase in pH decreased oxygen consumption, and an increase in conductivity was reported after treatment application. Conclusions: Even with higher concentrations of copper, the efficacy of MAP control was not complete. The concentration of copper must be a key element in achieving control of highly resistant microorganisms.

Antibacterial mechanism of Cu-bearing 430 ferritic stainless steel

Copper (Cu)-bearing stainless steel has testified its effectiveness to reduce the risk of bacterial infections. However, its antibacterial mechanism is still controversial. Therefore, three 430 ferritic stainless steels with different Cu contents are selected to conduct deeper research by the way of bacterial inactivation from two aspects of material and biology. Hereinto, electrochemical and antibacterial results show that the increase in Cu content simultaneously improves the corrosion resistance and antibacterial property of 430 stainless steel. In addition, it is found that Escherichia coli (E. coli) on the surface 430 Cu-bearing stainless steel by the dry method of inoculation possesses a rapid inactivation ability. X-ray photoelectron spectroscopy (XPS) aids with ion chelation experiments prove that Cu (I) plays a more crucial role in the contact-killing efficiency than Cu (II), resulting from more production of reactive oxygen species (ROS).

Quantitative Evaluation of Nucleic Acid Degradability of Copper Alloy Surfaces and Its Correlation to Antibacterial Activity

Copper (Cu) and its alloys have bactericidal activity known as “contact killing” with degradation of nucleic acids inside the bacteria, which is beneficial to inhibit horizontal gene transfer (HGF). In order to understand the nucleic acid degradability of Cu and its alloy surfaces, we developed a new in vitro method to quantitatively evaluate it by a swab method under a “dry” condition and compared it with that of commercially available antibacterial materials such as antibacterial stainless steel, pure silver, and antibacterial resins. As a result, only Cu and its alloys showed continuous degradation of nucleic acids for up to 6 h of contact time. The nucleic acid degradability levels of the Cu alloys and other antibacterial materials correlate to their antibacterial activities evaluated by a film method referring to JIS Z 2801:2012 for Gram-negative (Escherichia coli) and Gram-positive (Staphylococcus aureus) bacteria. Nucleic acid degradation by copper (I) and (II) chlorides was confirmed at the ranges over 10 mM and 1–20 mM, respectively, suggesting that the copper ion release may be responsible for the degradation of the nucleic acids on Cu and its alloy surfaces. In conclusion, the higher Cu content in the alloys gave higher nucleic acid degradability and higher antibacterial activities.

Proteomic Analysis of Copper Toxicity in Human Fungal Pathogen Cryptococcus neoformans

Cryptococcus neoformans is an invasive human fungal pathogen that causes more than 181,000 deaths each year. Studies have demonstrated that pulmonary C. neoformans infection induces innate immune responses involving copper, and copper detoxification in C. neoformans improves its fitness and pathogenicity during pulmonary C. neoformans infection. However, the molecular mechanism by which copper inhibits C. neoformans proliferation is unclear. We used a metallothionein double-knockout C. neoformans mutant that was highly sensitive to copper to demonstrate that exogenous copper ions inhibit fungal cell growth by inducing reactive oxygen species generation. Using liquid chromatography-tandem mass spectrometry, we found that copper down-regulated factors involved in protein translation, but up-regulated proteins involved in ubiquitin-mediated protein degradation. We propose that the down-regulation of protein synthesis and the up-regulation of protein degradation are the main effects of copper toxicity. The ubiquitin modification of total protein and proteasome activity were promoted under copper stress, and inhibition of the proteasome pathway alleviated copper toxicity. Our proteomic analysis sheds new light on the antifungal mechanisms of copper.

Coating Technologies for Copper Based Antimicrobial Active Surfaces: A Perspective Review

Microbial contamination of medical devices and treatment rooms leads to several detrimental hospital and device-associated infections. Antimicrobial copper coatings are a new approach to control healthcare-associated infections (HAI’s). This review paper focuses on the efficient methods for depositing highly adherent copper-based antimicrobial coatings onto a variety of metal surfaces. Antimicrobial properties of the copper coatings produced by various deposition methods including thermal spray technique, electrodeposition, electroless plating, chemical vapor deposition (CVD), physical vapor deposition (PVD), and sputtering techniques are compared. The coating produced using different processes did not produce similar properties. Also, process parameters often could be varied for any given coating process to impart a change in structure, topography, wettability, hardness, surface roughness, and adhesion strength. In turn, all of them affect antimicrobial activity. Fundamental concepts of the coating process are described in detail by highlighting the influence of process parameters to increase antimicrobial activity. The strategies for developing antimicrobial surfaces could help in understanding the mechanism of killing the microbes.

Resistance and Adaptation of Bacteria to Non-Antibiotic Antibacterial Agents: Physical Stressors, Nanoparticles, and Bacteriophages

Antimicrobial resistance is a significant threat to human health worldwide, forcing scientists to explore non-traditional antibacterial agents to support rapid interventions and combat the emergence and spread of drug resistant bacteria. Many new antibiotic-free approaches are being developed while the old ones are being revised, resulting in creating unique solutions that arise at the interface of physics, nanotechnology, and microbiology. Specifically, physical factors (e.g., pressure, temperature, UV light) are increasingly used for industrial sterilization. Nanoparticles (unmodified or in combination with toxic compounds) are also applied to circumvent in vivo drug resistance mechanisms in bacteria. Recently, bacteriophage-based treatments are also gaining momentum due to their high bactericidal activity and specificity. Although the number of novel approaches for tackling the antimicrobial resistance crisis is snowballing, it is still unclear if any proposed solutions would provide a long-term remedy. This review aims to provide a detailed overview of how bacteria acquire resistance against these non-antibiotic factors. We also discuss innate bacterial defense systems and how bacteriophages have evolved to tackle them.

Brass Alloys: Copper-Bottomed Solutions against Hospital-Acquired Infections?

Copper has been used for its antimicrobial properties since Antiquity. Nowadays, touch surfaces made of copper-based alloys such as brasses are used in healthcare settings in an attempt to reduce the bioburden and limit environmental transmission of nosocomial pathogens. After a brief history of brass uses, the various mechanisms that are thought to be at the basis of brass antimicrobial action will be described. Evidence shows that direct contact with the surface as well as cupric and cuprous ions arising from brass surfaces are instrumental in the antimicrobial effectiveness. These copper ions can lead to oxidative stress, membrane alterations, protein malfunctions, and/or DNA damages. Laboratory studies back up a broad spectrum of activity of brass surfaces on bacteria with the possible exception of bacteria in their sporulated form. Various parameters influencing the antimicrobial activity such as relative humidity, temperature, wet/dry inoculation or wear have been identified, making it mandatory to standardize antibacterial testing. Field trials using brass and copper surfaces consistently report reductions in the bacterial bioburden but, evidence is still sparse as to a significant impact on hospital acquired infections. Further work is also needed to assess the long-term effects of chemical/physical wear on their antimicrobial effectiveness.

A novel methodology to study antimicrobial properties of high-touch surfaces used for indoor hygiene applications-A study on Cu metal

Metal-based high-touch surfaces used for indoor applications such as doorknobs, light switches, handles and desks need to remain their antimicrobial properties even when tarnished or degraded. A novel laboratory methodology of relevance for indoor atmospheric conditions and fingerprint contact has therefore been elaborated for combined studies of both tarnishing/corrosion and antimicrobial properties of such high-touch surfaces. Cu metal was used as a benchmark material. The protocol includes pre-tarnishing/corrosion of the high touch surface for different time periods in a climatic chamber at repeated dry/wet conditions and artificial sweat deposition followed by the introduction of bacteria onto the surfaces via artificial sweat droplets. This methodology provides a more realistic and reproducible approach compared with other reported procedures to determine the antimicrobial efficiency of high-touch surfaces. It provides further a possibility to link the antimicrobial characteristics to physical and chemical properties such as surface composition, chemical reactivity, tarnishing/corrosion, surface roughness and surface wettability. The results elucidate that bacteria interactions as well as differences in extent of tarnishing can alter the physical properties (e.g. surface wettability, surface roughness) as well as the extent of metal release. The results clearly elucidate the importance to consider changes in chemical and physical properties of indoor hygiene surfaces when assessing their antimicrobial properties.

Cupric Oxide Coating That Rapidly Reduces Infection by SARS-CoV-2 via Solids

The ongoing COVID-19 pandemic has created a need for coatings that reduce infection from SARS-CoV-2 via surfaces. Such a coating could be used on common touch surfaces (e.g., door handles and railings) to reduce both disease transmission and fear of touching objects. Herein, we describe the design, fabrication, and testing of a cupric oxide anti-SARS-CoV-2 coating. Rapid loss of infectivity is an important design criterion, so a porous hydrophilic coating was created to allow rapid infiltration of aqueous solutions into the coating where diffusion distances to the cupric oxide surface are short and the surface area is large. The coating was deposited onto glass from a dispersion of cuprous oxide in ethanol and then thermally treated at 700 °C for 2 h to produce a CuO coating that is ≈30 μm thick. The heat treatment oxidized the cuprous oxide to cupric oxide and sintered the particles into a robust film. The SARS-CoV-2 infectivity from the CuO film was reduced by 99.8% in 30 min and 99.9% in 1 h compared to that from glass. The coating remained hydrophilic for at least 5 months, and there was no significant change in the cross-hatch test of robustness after exposure to 70% ethanol or 3 wt % bleach.

Copper-Modified Polymeric Membranes for Water Treatment: A Comprehensive Review

In the last decades, the incorporation of copper in polymeric membranes for water treatment has received greater attention, as an innovative potential solution against biofouling formation on membranes, as well as, by its ability to improve other relevant membrane properties. Copper has attractive characteristics: excellent antimicrobial activity, high natural abundance, low cost and the existence of multiple cost-effective synthesis routes for obtaining copper-based materials with tunable characteristics, which favor their incorporation into polymeric membranes. This study presents a comprehensive analysis of the progress made in the area regarding modified membranes for water treatment when incorporating copper. The notable use of copper materials (metallic and oxide nanoparticles, salts, composites, metal-polymer complexes, coordination polymers) for modifying microfiltration (MF), ultrafiltration (UF), nanofiltration (NF), forward osmosis (FO) and reverse osmosis (RO) membranes have been identified. Antibacterial and anti-fouling effect, hydrophilicity increase, improvements of the water flux, the rejection of compounds capacity and structural membrane parameters and the reduction of concentration polarization phenomena are some outstanding properties that improved. Moreover, the study acknowledges different membrane modification approaches to incorporate copper, such as, the incorporation during the membrane synthesis process (immobilization in polymer and phase inversion) or its surface modification using physical (coating, layer by layer assembly and electrospinning) and chemical (grafting, one-pot chelating, co-deposition and mussel-inspired PDA) surface modification techniques. Thus, the advantages and limitations of these modifications and their methods with insights towards a possible industrial applicability are presented. Furthermore, when copper was incorporated into membrane matrices, the study identified relevant detrimental consequences with potential to be solved, such as formation of defects, pore block, and nanoparticles agglomeration during their fabrication. Among others, the low modification stability, the uncontrolled copper ion releasing or leaching of incorporated copper material are also identified concerns. Thus, this article offers modification strategies that allow an effective copper incorporation on these polymeric membranes and solve these hinders. The article finishes with some claims about scaling up the implementation process, including long-term performance under real conditions, feasibility of production at large scale, and assessment of environmental impact.

Antibacterial effect of a copper-containing titanium alloy against implant-associated infection induced by methicillin-resistant Staphylococcus aureus

Implant-associated infection (IAI) induced by methicillin-resistant Staphylococcus aureus (MRSA) is a devastating complication in the orthopedic clinic. Traditional implant materials, such as Ti6Al4V, are vulnerable to microbial infection. In this study, we fabricated a copper (Cu)-containing titanium alloy (Ti6Al4V-Cu) for the prevention and treatment of MRSA-induced IAI. The material characteristics, antibacterial activity, and biocompatibility of Ti6Al4V-Cu were systematically investigated and compared with those of Ti6Al4V. Ti6Al4V-Cu provided stable and continuous Cu²⁺ release, at a rate of 0.106 mg/cm²/d. Its antibacterial performance against MRSA in vitro was confirmed by plate counting analysis, crystal violet staining, and scanning electron microscopic observations. Reverse transcription quantitative polymerase chain reaction (RT-qPCR) analysis demonstrated that Ti6Al4V-Cu suppressed biofilm formation, virulence, and antibiotic-resistance of MRSA. The in vivo anti-MRSA effect was investigated in a rat IAI model. Implants were contaminated with MRSA solution, implanted into the femur, and left for 6 weeks. Severe IAI developed in the Ti6Al4V group, with increased radiological score (9.6 ± 1.3) and high histological score (10.1 ± 1.9). However, no sign of infection was found in the Ti6Al4V-Cu group, as indicated by decreased radiological score (1.3 ± 0.4) and low histological score (2.3 ± 0.5). In addition, Ti6Al4V-Cu had favorable biocompatibility both in vitro and in vivo. In summary, Ti6Al4V-Cu is a promising implant material to protect against MRSA-induced IAI.

Copper Surfaces in Biofilm Control

Biofilms are structures comprising microorganisms associated to surfaces and enclosed by an extracellular polymeric matrix produced by the colonizer cells. These structures protect microorganisms from adverse environmental conditions. Biofilms are typically associated with several negative impacts for health and industries and no effective strategy for their complete control/eradication has been identified so far. The antimicrobial properties of copper are well recognized among the scientific community, which increased their interest for the use of these materials in different applications. In this review the use of different copper materials (copper, copper alloys, nanoparticles and copper-based coatings) in medical settings, industrial equipment and plumbing systems will be discussed considering their potential to prevent and control biofilm formation. Particular attention is given to the mode of action of copper materials. The putative impact of copper materials in the health and/or products quality is reviewed taking into account their main use and the possible effects on the spread of antimicrobial resistance.

Biological properties of copper-doped biomaterials for orthopedic applications: A review of antibacterial, angiogenic and osteogenic aspects

Copper is an essential trace element required for human life, and is involved in several physiological mechanisms. Today researchers have found and confirmed that Cu has biological properties which are particularly useful for orthopedic biomaterials applications such as implant coatings or biodegradable filler bone substitutes. Indeed, Cu exhibits antibacterial functions, provides angiogenic ability and favors osteogenesis; these represent major key points for ideal biomaterial integration and the healing process that follows. The antibacterial performances of copper-doped biomaterials present an interesting alternative to the massive use of prophylactic antibiotics and help to limit the development of antibiotic resistance. By stimulating blood vessel growth and new bone formation, copper contributes to the improved bio-integration of biomaterials. This review describes the bio-functional advantages offered by Cu and focuses on the antibacterial, angiogenic and osteogenic properties of Cu-doped biomaterials with potential for orthopedic applications.

Metallic Antibacterial Surface Treatments of Dental and Orthopedic Materials

The oral cavity harbors complex microbial communities, which leads to biomaterial-associated infections (BAI) during dental and orthopedic treatments. Conventional antibiotic treatments have met great challenges recently due to the increasing emergency of drug-resistant bacteria. To tackle this clinical issue, antibacterial surface treatments, containing surface modification and coatings, of dental and orthopedic materials have become an area of intensive interest now. Among various antibacterial agents used in surface treatments, metallic agents possess unique properties, mainly including broad-spectrum antibacterial properties, low potential to develop bacterial resistance, relative biocompatibility, and chemical stability. Therefore, this review mainly focuses on underlying antibacterial applications and the mechanisms of metallic agents in dentistry and orthopedics. An overview of the present review indicates that much work remains to be done to deepen the understanding of antibacterial mechanisms and potential side-effects of metallic agents.

Deposition of Copper on Polyester Knitwear Fibers by a Magnetron Sputtering System. Physical Properties and Evaluation of Antimicrobial Response of New Multi-Functional Composite Materials

In this study, copper films were deposited by magnetron sputtering on poly(ethylene terephthalate) knitted textile to fabricate multi-functional, antimicrobial composite material. The modified knitted textile composites were subjected to microbial activity tests against colonies of Gram-positive (Staphylococcus aureus) and Gram-negative (Escherichia coli) bacteria and antifungal tests against Chaetomium globosum fungal molds species. The prepared samples were characterized by UV/VIS transmittance, scanning electron microscopy (SEM), tensile and filtration parameters and the ability to block UV radiation. The performed works proved the possibility of manufacturing a new generation of antimicrobial textile composites with barrier properties against UV radiation, produced by a simple, zero-waste method. The specific advantages of using new poly(ethylene terephthalate)-copper composites are in biomedical applications areas.

Advances in Antibacterial Functionalized Coatings on Mg and Its Alloys for Medical Use—A Review

As a revolutionary implant material, magnesium and its alloys have many exciting performances, such as biodegradability, mechanical compatibility, and excellent biosecurity. However, the rapid and uncontrollable degradation rate of magnesium greatly hampers its clinical use. Many efforts have been taken to enhance the corrosion resistance of magnesium. However, it must be noted that improving the corrosion resistance of magnesium will lead to the compromise of its antibacterial abilities, which are attribute and proportional to the alkaline pH during its degradation. Providing antibacterial functionalized coating is one of the best methods for balancing the degradation rate and the antibacterial ability of magnesium. Antibacterial functionalized magnesium is especially well-suited for patients with diabetes and infected wounds. Considering the extremely complex biological environment in the human body and the demands of enhancing corrosion resistance, biocompatibility, osteogenesis, and antibacterial ability, composite coatings with combined properties of different materials may be promising. The aim of this review isto collect and compare recent studies on antibacterial functionalized coatings on magnesium and its alloys. The clinical applications of antibacterial functionalized coatings and their material characteristics, antibacterial abilities, in vitro cytocompatibility, and corrosion resistance are also discussed in detail.

A Surface Coating that Rapidly Inactivates SARS-CoV-2

SARS-CoV-2, the virus that causes the disease COVID-19, remains viable on solids for periods of up to 1 week, so one potential route for human infection is via exposure to an infectious dose from a solid. We have fabricated and tested a coating that is designed to reduce the longevity of SARS-CoV-2 on solids. The coating consists of cuprous oxide (Cu2O) particles bound with polyurethane. After 1 h on coated glass or stainless steel, the viral titer was reduced by about 99.9% on average compared to the uncoated sample. An advantage of a polyurethane-based coating is that polyurethane is already used to coat a large number of everyday objects. Our coating adheres well to glass and stainless steel as well as everyday items that people may fear to touch during a pandemic, such as a doorknob, a pen, and a credit card keypad button. The coating performs well in the cross-hatch durability test and remains intact and active after 13 days of being immersed in water or after exposure to multiple cycles of exposure to the virus and disinfection.

Validation of a Worst-Case Scenario Method Adapted to the Healthcare Environment for Testing the Antibacterial Effect of Brass Surfaces and Implementation on Hospital Antibiotic-Resistant Strains

The evaluation of antibacterial activity of metal surfaces can be carried out using various published guidelines which do not always agree with each other on technical conditions and result interpretation. Moreover, these technical conditions are sometimes remote from real-life ones, especially those found in health-care facilities, and do not include a variety of antibiotic-resistant strains. A worst-case scenario protocol adapted from published guidelines was validated on two reference strains (Staphylococcus aureus ATCC 6538 and Enterobacter aerogenes ATCC 13048). This protocol was designed to be as close as possible to a healthcare facility environment, including a much shorter exposure-time than the one recommended in guidelines, and evaluated the impact of parameters such as the method used to prepare inocula, seed on the surface, and recover bacteria following exposure. It was applied to a panel of 12 antibiotic-resistant strains (methicillin resistant, vancomycin-resistant, beta-lactamase, and carbapenemase producing strains as well as efflux pump-overexpressing ones) chosen as representative of the main bacteria causing hospital acquired infections. Within a 5-min exposure time, the tested brass surface displayed an antibacterial effect meeting a reduction cut-off of 99% compared to stainless steel, whatever the resistance mechanism harbored by the bacteria.

In vitro evaluation of antimicrobial efficacy and durability of three copper surfaces used in healthcare

Antimicrobial properties of solid copper (Cu) surfaces against various microorganisms have been demonstrated, but little is known about the durability and relative antimicrobial efficacy of different Cu formulations currently used in healthcare. The aim of this study was to assess whether three different formulations of copper-bearing alloys (integral, spray-on and Cu-impregnated surfaces) and a stainless steel control differed in their antimicrobial efficacy, durability, and compatibility with hospital-grade cleaner/disinfectants. The U.S. Environmental Protection Agency draft protocol for the evaluation of bactericidal activity of Cu containing alloys was modified to more accurately reflect cleaning methods in healthcare. The three different Cu alloys were evaluated using 25 × 25 × 3 mm disks subjected to one year of simulated cleaning and disinfection using the Wiperator™ with microfiber cloths presoaked in three common hospital disinfectants: accelerated hydrogen peroxide, quaternary ammonium, or sodium hypochlorite solutions. Bactericidal activity was evaluated using Staphylococcus aureus and Pseudomonas aeruginosa. While all Cu formulations exhibited some antimicrobial activity, integral and spray-on Cu alloys showed the greatest efficacy. Assessments of durability included documentation of changes in mass, morphological changes by scanning electron microscopy, chemical composition alteration by energy-dispersive x-ray spectroscopy, and surface roughness alteration using profilometry over one year of simulated use. The integral Cu alloy had the least mass loss (0.20% and 0.19%) and abrasion-corrosion rate (6.28 and 6.09 μm/yr) compared to stainless steel. The integral product also showed the highest durability. Exposure to disinfectants affected both the antimicrobial efficacy and durability of the various copper products.

Optimization of Antibacterial Properties of “Hybrid” Metal-Sputtered Superhydrophobic Surfaces

Bacterial attachment and colonization to hygiene sensitive surfaces, both public and nosocomial, as well as in food industry areas, poses a serious problem to human healthcare. Several infection incidents are reported, while bacterial resistance to antibiotics is increasing. Recently, novel techniques for the design of antibacterial surfaces to limit bacterial spreading have emerged, including bifunctional antibacterial surfaces with antifouling and bactericidal action. In this context, we have recently developed smart, universal, metal-sputtered superhydrophobic surfaces, demonstrating both bacterial repulsion and killing efficacy. Herein, we present the optimization process that led to the realization of these “hybrid” antibacterial surfaces. To this end, two bactericidal agents, silver and copper, were tested for their efficiency against Gram-negative bacteria, with copper showing a stronger bactericidal action. In addition, between two low surface energy coatings, the fluorinated-alkyl self-assembled chlorosilane layer from perfluorinated octyltrichlorosilane (pFOTS) solution and the fluorocarbon layer from octafluorocyclobutane (C4F8) plasma were both approved for their anti-adhesive properties after immersion in bacterial solution. However, the latter was found to be more efficient when engrafted with the bactericidal agent in shielding its killing performance. Furthermore, the thickness of the plasma-deposited fluorocarbon layer was optimized, in order to simultaneously retain both the superhydrophobicity of the surface and its long-term bactericidal activity.

Essential oil-incorporated carbon nanotubes filters for bacterial removal and inactivation

In this study, essential oils (EO)-incorporated multi-walled carbon nanotubes (MWCNTs) filters were developed for achieving dual functions in effective removing bacteria from aqueous solutions and inactivating bacteria cells captured on the filters. Tea tree essential oil (TTO), lemon essential oil (LEO), and TTO-LEO-mixture were coated on MWCNTs filters with different MWCNTs loadings ranging from 3 mg to 6 mg. MWCNTs filters with 6.0 mg MWCNTs showed complete removal (100%) of E. coli cells from PBS buffer with 6.35 log10 decrease of cell numbers. TTO, LEO, and TTO/LEO Mix (1:1) coatings at the volume of 50 μL on MWCNTs filters achieved bacterial removal rates of >98%, and highly effective inactivation efficiency. TTO coatings had the highest antimicrobial efficacies than LEO and Mix coatings, MWCNTs filters with 50 μL TTO coating showed 100% inhibitory rate of the captured bacteria on the filter surfaces. Those captured but survived cells on filters with less TTO coating (20μL) significantly reduced their salt tolerances to 30 and 40 g/L NaCl in LB agar, and became less salt tolerance with longer incubation time on the filters. The developed TTO-MWCNTs filters had much higher antimicrobial efficacies than the filters with dual functions developed previously.

Antibacterial Copper-Hydroxyapatite Composite Coatings via Electrochemical Synthesis

Antibacterial copper-hydroxyapatite (Cu-HA) composite coatings on titanium were synthesized using a novel process consisting of two consecutive electrochemical reactions. In the first stage, HA nanocrystals were grown on titanium using the cathodic electrolytic synthesis. The HA-coated titanium was then used as the cathode in a second reaction stage to electrochemically reduce Cu²⁺ ions in solution to metallic Cu nanoparticles. Reaction conditions were found that result in nanoscale Cu particles growing on the surface of the HA crystals. The two-stage synthesis allows facile control of copper content in the HA coatings. Antibacterial activity was measured by culturing Escherichia coli (Gram-negative) and Staphylococcus aureus (Gram-positive) in the presence of coatings having varying copper contents. The coatings displayed copper concentration-dependent antibacterial activity against both types of bacteria, likely due to the slow release of copper ions from the coatings. The observation of antibacterial activity from a relatively low loading of copper on the bioactive HA support suggests that multifunctional implant coatings can be developed to supplement or supplant prophylactic antibiotics used in implant surgery that are responsible for creating resistant bacteria strains.

Influence of chlorides and phosphates on the antiadhesive, antibacterial, and electrochemical properties of an electroplated copper-silver alloy

Antimicrobial surfaces such as copper alloys can reduce the spread of pathogenic microorganisms, e.g., in healthcare settings; however, the surface chemistry and thus the antibacterial activity are influenced by environmental parameters such as cleaning and disinfection procedures. Therefore, the purpose of the present study was to assess how copper-complexing compounds (chlorides and phosphates), common to the clinical environment, can affect the surface chemistry and the antiadhesive and antibacterial properties of a newly developed antibacterial copper-silver alloy and the single alloying metals. The authors demonstrated that the antiadhesion efficacy against S. aureus 8325 was the highest when the copper-silver alloy and copper surfaces (four- and two-log bacterial reduction compared to stainless steel controls, respectively) were exposed to chloride-containing suspensions. This was explained by the electrochemical activity of copper that dissolved as Cu⁺, highly toxic to the bacterial cells, in the presence of Cl^- and eventually formed a chlorine- and oxygen-rich layer with the incorporation of phosphorus, if also phosphates were present. If chlorides were omitted from the wet environment, there was no difference (P > 0.05) in bacterial counts on copper-silver alloy, copper, silver, and AISI 316 stainless steel control surfaces, due to the fact that no oxidizing conditions were established and therefore there was no dissolution of copper ions from copper-silver alloy and copper surfaces. However, under dry conditions, copper-silver alloy and pure copper surfaces were antibacterial also in the absence of chlorides, suggesting a marked difference between dry and wet conditions in terms of the interactions between surfaces and bacteria. The authors conclude that an attentive design of control policies integrating disinfection interventions and antimicrobial surfaces, such as the copper-silver alloy coating, can be a beneficial solution in fighting the spread of antibiotic resistant bacterial strains and potentially reducing the number of disease outbreaks.

Relationship between Dislocation Density and Antibacterial Activity of Cryo-Rolled and Cold-Rolled Copper

In the present work, cold rolling and cryo-rolling were performed on 99% commercially pure copper substrates. Both cold and cryo-rolling processes caused severe plastic deformation that led to an increase in dislocation density by 14× and 28× respectively, as compared to the pristine material. Increases in average tensile strengths, by 75% (488 MPa) and 150% (698 MPa), were observed in the two rolled materials as the result of the enhancement in dislocation density. In addition to strength, enhanced antibacterial property of cryo-rolled copper was observed in comparison to cold rolled and pristine copper. Initial adhesion and subsequent proliferation of bio-film forming Gram-positive bacteria Staphylococcus aureus was reduced by 66% and 100% respectively for cryo-rolled copper. Approximately 55% protein leakage, as well as ethidium bromide (EtBr) uptake, were observed confirming rupture of cell membrane of S. aureus. Inductively coupled plasma-mass spectroscopy reveals higher leaching of elemental copper in nutrient broth media from the cryo-rolled copper. Detailed investigations showed that increased dislocation led to leaching of copper ions that caused damage to the bacterial cell wall and consequently killing of bacterial cells. Cryo-rolling enhanced both strength, as well as antibacterial activity, due to the presence of dislocations.

Influence of Dental Prosthesis and Restorative Materials Interface on Oral Biofilms

Oral biofilms attach onto both teeth surfaces and dental material surfaces in oral cavities. In the meantime, oral biofilms are not only the pathogenesis of dental caries and periodontitis, but also secondary caries and peri-implantitis, which would lead to the failure of clinical treatments. The material surfaces exposed to oral conditions can influence pellicle coating, initial bacterial adhesion, and biofilm formation, due to their specific physical and chemical characteristics. To define the effect of physical and chemical characteristics of dental prosthesis and restorative material on oral biofilms, we discuss resin-based composites, glass ionomer cements, amalgams, dental alloys, ceramic, and dental implant material surface properties. In conclusion, each particular chemical composition (organic matrix, inorganic filler, fluoride, and various metallic ions) can enhance or inhibit biofilm formation. Irregular topography and rough surfaces provide favorable interface for bacterial colonization, protecting bacteria against shear forces during their initial reversible binding and biofilm formation. Moreover, the surface free energy, hydrophobicity, and surface-coating techniques, also have a significant influence on oral biofilms. However, controversies still exist in the current research for the different methods and models applied. In addition, more in situ studies are needed to clarify the role and mechanism of each surface parameter on oral biofilm development.