CaF2 Nanoparticle-Induced γ-CsPbI2.81Br0.19 Heterogeneous Crystallization for High-Efficiency Flexible All-Inorganic Perovskite Solar Cells

All-inorganic CsPbI3 films necessitate higher annealing temperatures for high-quality crystallization. Consequently, the conventional low-temperature solution approach often results in poor crystallization in flexible CsPbI3 films, significantly degrading the optoelectronic performance and stability of flexible perovskite solar cells (f-PSCs). Herein, a heterogeneous CaF2 nanocrystal seed-induced strategy has been successfully utilized to achieve enhanced crystallization of a flexible CsPbI2.81Br0.19 film. Due to their good lattice match with the perovskite material, CaF2 nanoparticles can decrease the critical Gibbs free energy of CsPbI2.81Br0.19 perovskite nucleation, thereby accelerating γ-phase CsPbI2.81Br0.19 crystallization at low temperatures. This leads to an improved crystalline quality of the flexible perovskite film at low temperatures, which minimizes defects and enhances the stability of f-PSCs. The CsPbI2.81Br0.19 f-PSCs achieved a champion power conversion efficiency of 15.03% and demonstrated mechanical stability, retaining 98.1% of their initial efficiency even after 60 000 bending cycles with a curvature radius of 5 mm.

Enhancing Optoelectronic Performance of All-Inorganic Double Perovskites via Halogen Doping: Synergistic Screening Strategies and Multiscale Simulations

Designing all-inorganic double perovskites through element mixing is a promising strategy to enhance their optoelectronic performance and structural stability. The complex interplay between multilevel structures and optoelectronic properties in element-mixed double perovskites necessitates further in-depth theoretical exploration. In this study, we employ screening strategies and multiscale simulations combining first-principles methods and device-scale continuum models to identify two novel element-mixed compounds, Rb2AgInCl3I3 and Cs2AgInCl3I3, as promising candidates for photovoltaic applications. These compounds exhibit favorable structural factors and suitable direct band gaps. Theoretical investigations using first-principles methods with the HSE06 functional reveal direct band gaps of 0.98 and 1.26 eV for Rb2AgInCl3I3 and Cs2AgInCl3I3, respectively, with corresponding optical absorption coefficients exceeding 105 cm-1 in the visible light range. Cs2AgInCl3I3 features high charge mobilities of approximately 20 cm2·V-1·s-1 and a notable single-junction spectroscopic limited maximum efficiency (SLME) of 25.54%. Further analysis using the device-scale continuum model simulated the nonradiative recombination effects on power conversion efficiency, integrating quantum-mechanically calculated optoelectronic properties. These theoretical investigations, which bridge composition engineering with multiscale simulations, provide valuable insights into screening novel, lead-free, halogen-mixed double metal perovskite optoelectronic devices, highlighting their potential for high-performance solar energy applications.

Ternary Ag3AuS2 Nanocrystals for Thin-Film Solar Cells

The concept of clean and pollution-free energy development has promoted the rise of environmentally friendly silver-based chalcogenide nanocrystal (NC) solar cells, but currently reported silver-based NCs need complex synthesis processes at high temperatures that may bring zerovalent noble metal impurities for their high redox potentials. In this study, we report a facile synthesis of novel Ag3AuS2 NCs by injecting highly active oleylamine sulfur complexes as sulfur sources into metal precursor solutions at low temperatures of 60 °C. The obtained Ag3AuS2 NCs exhibit broad absorption spectra and high molar extinction coefficients (106 M-1 cm-1). Then, the Ag3AuS2 NCs are applied as the light-absorbing active layer in environmentally friendly thin-film solar cells. By introducing a hybrid mixture of charge acceptors and donors (NCs/P3HT hybrid film) at the interface, the device gains an absorption increment and enhanced charge extraction, achieving a final power conversion efficiency of 3.38%. This work demonstrates the enormous potential of Ag3AuS2 NCs from low-temperature preparation for photovoltaic applications.

Fabrication of Efficient and Simple-Structured Perovskite Solar Cells Using a Multifunctional Biocolina Surface Treatment

The electron transport layer (ETL)-free perovskite solar cells (PSCs) have gained significant interest by simplifying the manufacture process and reducing the time/energy required for the fabrication of ETLs. Unfortunately, the performance of these ETL-free PSCs still lags behind those of the conventional counterparts due to the slow electron extraction and undesired interfacial charge recombination loss at the buried interface. In this work, a facile and multifunctional biocolina thin layer is incorporated on the bottom electrodes to regulate the interface energy level alignment by forming an interface dipole layer, resulting in a suppressed nonradiative recombination and an improved charge extraction. Furthermore, the biocolina thin layer possess the capability to passivate the surface defects within the perovskite films while simultaneously facilitate the formation of perovskite crystals. Consequently, a remarkable enhancement in photovoltaic performance is observed in the biocolina-based ETL-free PSCs with an increase from 15.96 % to an outstanding 20.01 %. Additionally, the biocolina extends the stability and relieves the hysteresis effect through the interface defect passivation and inhibition of interface charge accumulation. This research contributes to the development of cost-effective, simplified designs for highly efficient ETL-free PSCs by modifying the bottom electrodes.

Deploying a Dipole Electric Field at the CsPbI3 Perovskite/Carbon Interface for Enhancing Hole Extraction and Photovoltaic Performance

Carbon-based CsPbI3 perovskite solar cells without hole transporter (C-PSCs) have achieved intense attention due to its simple device structure and high chemical stability. However, the severe interface energy loss at the CsPbI3/carbon interface, attributed to the lower hole selectivity for inefficient charge separation, greatly limits device performance. Hence, dipole electric field (DEF) is deployed at the above interface to address the above issue by using a pole molecule, 4-trifluoromethyl-Phenylammonium iodide (CF3-PAI), in which the ─NH3 group anchors on the perovskite surface and the ─CF3 group extends away from it and connects with carbon electrode. The DEF is proven to align with the built-in electric field, that is pointing toward carbon electrode, which well enhances hole selectivity and charge separation at the interface. Besides, CF3-PAI molecules also serve as defect passivator for reducing trap state density, which further suppresses defect-induced non-radiative recombination. Consequently, the CsPbI3 C-PSCs achieve an excellent efficiency of 18.33% with a high VOC of 1.144 V for inorganic C-PSCs without hole transporter.

High defect tolerance β-CsSnI3 perovskite light-emitting diodes

All-inorganic lead-free CsSnI3 has shown promising potential in optoelectronic applications, particularly in near-infrared perovskite light-emitting diodes (Pero-LEDs). However, non-radiative recombination induced by defects hinders the optoelectronic properties of CsSnI3-based Pero-LEDs, limiting their potential applications. Here, we uncovered that β-CsSnI3 exhibits higher defect tolerance compared to orthorhombic γ-CsSnI3, offering a potential for enhancing the emission efficiency. We further reported on the deposition and stabilization of highly crystalline β-CsSnI3 films with the assistance of cesium formate to suppress electron-phonon scattering and reduce nonradiative recombination. This leads to an enhanced photoluminescence quantum yield up to ∼10%. As a result, near-infrared LEDs based on β-CsSnI3 emitters are achieved with a peak external quantum efficiency of 1.81% and excellent stability under a high current injection of 1.0 A cm-2.

Synergistic Effect of Defects Passivation and Energy Level Alignment Realizing P3HT-Based High-Efficiency CsPbI3 Perovskite Solar Cells

Poly (3-hexylthiophene) (P3HT) is one of the most efficient hole transport layers (HTLs) in perovskite solar cells (PSCs). However, surface and boundary defects in CsPbI3, and energy level mismatch between CsPbI3 and P3HT lead to a low power conversion efficiency (PCE) in P3HT-based CsPbI3 PSCs. Here, a synergistic strategy with anti-solvent (sec-pentyl alcohol, 2-PA) and passivators (LiX, X = F, Cl, Br, I) is developed to promote the photovoltaic performance of P3HT-based CsPbI3 PSCs. It is proved that the 2-PA washes away the residual DMF and DMAPbI3, and assists the secondary growth of CsPbI3 crystal. LiX not only can passivate iodine (I) vacancies, but also can reduce energy offset at CsPbI3/P3HT interface, accelerating hole extraction process. Finally, an impressive efficiency of 19.26% is obtained due to the synergistic effect of defects passivation and energy alignment, which is 34.4% higher than the 14.32% achieved in Control cell. These findings prove that synergistic strategy of defects passivation and energy alignment is an effective way for realizing high-efficiency in P3HT-based CsPbI3 PSCs.

Enhanced Responsivity and Photostability of Cs3Bi2I9-Based Self-Powered Photodetector via Chemical Vapor Deposition Engineering

Lead-based halide perovskites have gained significant prominence in recent years in optoelectronics and photovoltaics, owing to their exceptional optoelectronic properties. Nonetheless, the toxicity of lead (Pb) and the stability concern pose obstacles to their potential for future large-scale market development. Herein, stable lead-free Cs3Bi2I9 (CBI) films are presented with smooth and compact morphologies synthesized via chemical vapor deposition (CVD), demonstrating their application as an UV photodetector in a self-powered way. The self-powered photodetectors (SPDs) exhibit remarkable characteristics, including a responsivity of 1.57 A W-1 and an impressive specific detectivity of 3.38 × 1013 Jones under the illumination of 365 nm at zero bias. Furthermore, the SPDs exhibit a nominal decline (≈2.2%) in the photocurrent under constant illumination over 500 h, highlighting its impressive long-term operational stability. Finally, the real-time UV-detection capability of the device is demonstrated by measuring the photocurrent under various conditions, including room light and sunlight at different times. These findings offer a new platform for synthesizing stable and high-quality perovskite films, and SPDs for advancing the development of wearable and portable electronics.

Synchrotron Radiation-Based In Situ GIWAXS for Metal Halide Perovskite Solution Spin-Coating Fabrication

Solution-processable perovskite-based devices are potentially very interesting because of their relatively cheap fabrication cost but outstanding optoelectronic performance. However, the solution spin-coating process involves complicated processes, including perovskite solution droplets, nucleation of perovskite, and formation of intermediate perovskite films, resulting in complicated crystallization pathways for perovskite films under annealing. Understanding and therefore controlling the fabrication process of perovskites is difficult. Recently, synchrotron radiation-based in situ grazing-incidence wide-angle X-ray scattering (GIWAXS) techniques, which possess the advantages of high collimation, high resolution, and high brightness, have enabled to bridge complicated perovskite structure information with device performance by revealing the real-time crystallization pathways of perovskites during the spin-coating process. Herein, the developments of synchrotron radiation-based in situ GIWAXS are discussed in the study of the crystallization process of perovskites, especially revealing the important crystallization mechanisms of state-of-the-art perovskite optoelectronic devices with high performance. At the end, several potential applications and challenges associated with in situ GIWAXS techniques for perovskite-based devices are highlighted.

Pattern-Matched Polymer Ligands Toward Near-Perfect Synergistic Passivation for High-Performance and Stable Br/Cl Mixed Perovskite Light-Emitting Diodes

Mixed Br/Cl perovskite nanocrystals (PeNCs) exhibit bright pure-blue emission benefiting for fulfilling the Rec. 2100 standard. However, phase segregation remains a significant challenge that severely affects the stability and emission spectrum of perovskite light-emitting diodes (PeLEDs). Here, we demonstrate the optimization of the spacing between polydentate functional groups of polymer ligands to match the surface pattern of CsPbBr1.8Cl1.2 PeNCs, resulting in effective synergistic passivation effect and significant improvements in PeLED performances. The block and alternating copolymers with different inter-functional group spacing are facilely synthesized as ligands for PeNCs. Surprisingly, block copolymers with a higher functional group density do not match PeNCs, while alternating copolymers enable efficient PeNCs with the high photoluminescence intensity, low non-radiative recombination rate and high exciton binding energy. Density functional theory calculations clearly confirm the almost perfect match between alternating copolymers and PeNCs. Finally, pure-blue PeLEDs are achieved with the emission at 467 nm and Commission Internationale de l'Eclairage (CIE) coordinates of (0.131, 0.071), high external quantum efficiency (9.1 %) and record spectral and operational stabilities (~80 mins) in mixed-halide PeLEDs. Overall, this study contributes to designing the polymer ligands and promoting the development of high-performance and stable pure-color PeLEDs towards display applications.

Amorphous (lysine)2PbI2 layer enhanced perovskite photovoltaics

Passivation materials play a crucial role in a wide range of high-efficiency, high-stability photovoltaic applications based on crystalline silicon and state-of-the-art perovskite materials. Currently, for perovskite photovoltaic, the mainstream passivation strategies routinely rely on crystalline materials. Herein, we have invented a new amorphous (lysine)2PbI2 layer-enhanced halide perovskite. By utilizing a solid phase reaction between PbI2 and lysine molecule, an amorphous (lysine)2PbI2 layer is formed at surface/grain boundaries in the perovskite films. The amorphous (lysine)2PbI2 with fewer dangling bonds can effectively neutralize surface/interface defects, achieving an impressive efficiency of 26.27% (certified 25.94%). Moreover, this amorphous layer not only reduces crystal lattice stress but also functions as a barrier against the decomposition of organic components, leading to suppressed de-structuring of perovskite and highly stable perovskite solar cells.

Eliminating Hole Extraction Barrier in 1D/3D Perovskite Heterojunction for Efficient and Stable Carbon-Based CsPbI3 Solar Cells with a Record Efficiency

Carbon-based perovskite solar cells (C-PSCs) have the advantages of low-cost and high-stability, but their photovoltaic performance is limited by severe defect-induced recombination and low hole extraction efficiency. 1D perovskite is proven to effectively passivate the defects on the perovskite surface, therefore reducing non-radiative recombination loss. However, the unsuitable energy level of most 1D perovskite renders an undesired downward band bending for 3D perovskite, resulting in a high hole extraction barrier and reduced hole extraction efficiency. Therefore, rational design and selection of 1D perovskites as the modifiers are essential in balancing defect passivation and hole extraction. In this work, based on simulation calculations, thiocholine iodide (TchI) is selected to prepare 1D perovskite with high work function and then constructs TchPbI3/CsPbI3 1D/3D perovskite heterojunction. Experimental results show that this strategy eliminates the hole extraction barrier at the perovskite/carbon interface, which improves the hole extraction efficiency of corresponding devices. Meanwhile, the strong interaction between the thiol group and Pb suppresses defect-induced recombination effectively and improves the stability of CsPbI3. The assembled C-PSCs exhibit a champion efficiency of 19.08% and a certified efficiency of 18.7%. To the best of the knowledge, this is a new efficiency record for inorganic C-PSCs.

Controlled Crystal Growth of All-Inorganic CsPbI2Br via Sequential Vacuum Deposition for Efficient Perovskite Solar Cells

Vacuum deposition of perovskites is a promising method for scale-up fabrication and uniform film growth. However, improvements in the photovoltaic performance of perovskites are limited by the fabrication of perovskite films, which are not optimized for high device efficiency in the vacuum evaporation process. Herein, we fabricate CsPbI2Br perovskite with high crystallinity and larger grain size by controlling the deposition sequence between PbI2 and CsBr. The nucleation barrier for perovskite formation is significantly lowered by first evaporating CsBr and then PbI2 (CsBr-PbI2), followed by the sequential evaporation of multiple layers. The results show that the reduced Gibbs free energy of CsBr-PbI2, compared with that of PbI2-CsBr, accelerates perovskite formation, resulting in larger grain size and reduced defect density. Furthermore, surface-modified homojunction perovskites are fabricated to efficiently extract charge carriers and enhance the efficiency of perovskite solar cells (PeSCs) by modulating the final PbI2 thickness before thermal annealing. Using these strategies, the best PeSC exhibits a power conversion efficiency of 13.41% for a small area (0.135 cm2), the highest value among sequential thermal deposition inorganic PeSCs, and 11.10% for a large area PeSC (1 cm2). This study presents an effective way to understand the crystal growth of thermally deposited perovskites and improve their performance in optoelectronic devices.

Hot Carrier Trapping and It's Influence to the Carrier Diffusion in CsPbBr3 Perovskite Film Revealed by Transient Absorption Microscopy

The defects in perovskite film can cause charge carrier trapping which shortens carrier lifetime and diffusion length. So defects passivation has become promising for the perovskite studies. However, how defects disturb the carrier transport and how the passivating affects the carrier transport in CsPbBr3 are still unclear. Here the carrier dynamics and diffusion processes of CsPbBr3 and LiBr passivated CsPbBr3 films are investigated by using transient absorption spectroscopy and transient absorption microscopy. It's found that there is a fast hot carrier trapping process with the above bandgap excitation, and the hot carrier trapping would decrease the population of cold carriers which are diffusible, then lower the carrier diffusion constant. It's proved that LiBr can passivate the defect and lower the trapping probability of hot carriers, thus improve the carrier diffusion rate. The finding demonstrates the influence of hot carrier trapping to the carrier diffusion in CsPbBr3 film.

Residual Stress Mitigation in Perovskite Solar Cells via Butterfly-Inspired Hierarchical PbI2 Scaffold

Residual stress in metal halide perovskite films intimately affects the photovoltaic figure of merit and longevity of perovskite solar cells. A delicate management of the crystallization kinetics is critical to the preparation of high-quality perovskite films. Only very limited methods, however, are available to regulate the residual stress of a perovskite film in a controllable manner, particularly for a perovskite film fabricated by a two-step method. Here, we demonstrate the construction of a hierarchical PbI2 scaffold inspired by Archaeoprepona demophon butterfly by combining an interlayer guided growth of porous structure and nanoimprinting. The hierarchically structured PbI2 that emulates the physical structure of the butterfly wing scale permits unimpeded permeation of organic amine salts and sufficient space for volume expansion during the crystallization process, accompanied by preferential perovskite growth of a defectless (001) crystal plane. The optimized perovskite film outperforms the control with reduced residual stress and defect density. Consequently, perovskite solar cells with a respectable power conversion efficiency reaching 23.4% (certified 23%) and an impressive open-circuit voltage of 1.184 V can be achieved. The target device can maintain 80% of initial efficiency after maximum power point tracking under illumination for 700 h. This work expands the range of engineering toward PbI2 by exploring a simultaneously tailored morphology and crystallinity and highlights the significance of a hierarchical PbI2 scaffold as an alternative choice to mitigate residual stress in a two-step processed perovskite active layer and boost the longevity of perovskite solar cells.

All-Inorganic Perovskite Solar Cells: Defect Regulation and Emerging Applications in Extreme Environments

All-inorganic perovskite solar cells (PSCs), such as CsPbX3, have garnered considerable attention recently, as they exhibit superior thermodynamic and optoelectronic stabilities compared to the organic-inorganic hybrid PSCs. However, the power conversion efficiency (PCE) of CsPbX3 PSCs is generally lower than that of organic-inorganic hybrid PSCs, as they contain higher defect densities at the interface and within the perovskite light-absorbing layers, resulting in higher non-radiative recombination and voltage loss. Consequently, defect regulation has been adopted as an important strategy to improve device performance and stability. This review aims to comprehensively summarize recent progresses on the defect regulation in CsPbX3 PSCs, as well as their cutting-edge applications in extreme scenarios. The underlying fundamental mechanisms leading to the defect formation in the crystal structure of CsPbX3 PSCs are firstly discussed, and an overview of literature-adopted defect regulation strategies in the context of interface, internal, and surface engineering is provided. Cutting-edge applications of CsPbX3 PSCs in extreme environments such as outer space and underwater situations are highlighted. Finally, a summary and outlook are presented on future directions for achieving higher efficiencies and superior stability in CsPbX3 PSCs.

Solvent-free preparation and thermocompression self-assembly: an exploration of performance improvement strategies for perovskite solar cells

Perovskite solar cells (PSCs) exhibit sufficient technological efficiency and economic competitiveness. However, their poor stability and scalability are crucial factors limiting their rapid development. Therefore, achieving both high efficiency and good stability is an urgent challenge. In addition, the preparation methods for PSCs are currently limited to laboratory-scale methods, so their commercialization requires further research. Effective packaging technology is essential to protect the PSCs from degradation by external environmental factors and ensure their long-term stability. The industrialization of PSCs is also inseparable from the preparation technology of perovskite thin films. This review discusses the solvent-free preparation of PSCs, shedding light on the factors that affect PSC performance and strategies for performance enhancement. Furthermore, this review analyzes the existing simulation techniques that have contributed to a better understanding of the interfacial evolution of PSCs during the packaging process. Finally, the current challenges and possible solutions are highlighted, providing insights to facilitate the development of highly efficient and stable PSC modules to promote their widespread application.

Photovoltaic-driven Ni(ii)/Ni(iii) redox mediator for the valorization of PET plastic waste with hydrogen production

Electrocatalytic valorization of PET plastic waste provides an appealing route by converting intermittent renewable energy into valuable chemicals and high-energy fuels. Normally, anodic PET hydrolysate oxidation and cathodic water reduction reactions occur simultaneously in the same time and space, which increases the challenges for product separation and operational conditions. Although these problems can be addressed by utilizing membranes or diaphragms, the parasitic cell resistance and high overall cost severely restrict their future application. Herein, we introduce a Ni(ii)/Ni(iii) redox mediator to decouple these reactions into two independent processes: an electrochemical process for water reduction to produce hydrogen fuel assisted by the oxidation of the Ni(OH)2 electrode into the NiOOH counterpart, followed subsequently by a spontaneous chemical process for the valorization of PET hydrolysate to produce formic acid with a high faradaic efficiency of ∼96% by the oxidized NiOOH electrode. This decoupling strategy enables the electrochemical valorization of PET plastic waste in a membrane-free system to produce high-value formic acid and high-purity hydrogen production. This study provides an appealing route to facilitate the transformation process of PET plastic waste into high-value products with high efficiency, low cost and high purity.

Nanoscale Local Contacts Enable Inverted Inorganic Perovskite Solar Cells with 20.8 % Efficiency

Inorganic perovskite solar cells (IPSCs) have gained significant attention due to their excellent thermal stability and suitable band gap (~1.7 eV) for tandem solar cell applications. However, the defect-induced non-radiative recombination losses, low charge extraction efficiency, energy level mismatches, and so on render the fabrication of high-efficiency inverted IPSCs remains challenging. Here, the use of 3-amino-5-bromopyridine-2-formamide (ABF) in methanol was dynamically spin-coated on the surface of CsPbI2.85Br0.15 film, which facilitates the limited etching of defect-rich subsurface layer, resulting in the formation of vertical PbI2 nanosheet structures. This enabled localized contacts between the perovskite film and the electron transport layer, suppress the recombination of electron-hole and beneficial to electron extraction. Additionally, the C=O and C=N groups in ABF effectively passivated the undercoordinated Pb2+ at grain boundaries and on the surface of CsPbI2.85Br0.15 film. Eventually, we achieved a champion efficiency of 20.80 % (certified efficiency of 20.02 %) for inverted IPSCs with enhanced stability, which is the highest value ever reported to date. Furthermore, we successfully prepared p-i-n type monolithic inorganic perovskite/silicon tandem solar cells (IPSTSCs) with an efficiency of 26.26 %. This strategy provided both fast extraction and efficient passivation at the electron-selective interface.

Hierarchical pore structure with a confined resonant mode for improving the solar energy utilizing efficiency of ultra-thin perovskite solar cells

The perovskite solar cell (PSC) has the benefits of flexibility, inexpensiveness, and high efficiency, and has important prospective applications. However, serious optical losing and low solar energy-utilizing efficiency remain a challenge for the ultra-thin PSCs because of the interface reflection of traditional planar structure. In this study, a hierarchical pore structure with a confined resonant mode is introduced and optimized by electromagnetic theory to improve the solar energy absorbing and utilizing efficiency of ultra-thin PSCs. The large pores in the top layer that support a whispering gallery mode can focus and guide the incident light into the solar cell. The small pores in the bottom layer enable backward scattering of the unabsorbed light and can improve the effective absorption of active layer. The finite-difference time-domain method is employed to optimize the geometric parameters of hierarchical pore structure to improve the light absorption of PSCs. The proposed resonant hierarchical pore structure can greatly improve sunlight absorption of ultra-thin PSCs, and the effective light absorption and photocurrent of PSCs with a hierarchical pore structure is 20.7% higher than that of PSCs with traditional planar structure. This work can offer a beneficial guideline for improving solar energy utilizing efficiency of various thin-film solar cells.

Textured Perovskite/Silicon Tandem Solar Cells Achieving Over 30% Efficiency Promoted by 4-Fluorobenzylamine Hydroiodide

Monolithic textured perovskite/silicon tandem solar cells (TSCs) are expected to achieve maximum light capture at the lowest cost, potentially exhibiting the best power conversion efficiency. However, it is challenging to fabricate high-quality perovskite films and preferred crystal orientation on commercially textured silicon substrates with micrometer-size pyramids. Here, we introduced a bulky organic molecule (4-fluorobenzylamine hydroiodide (F-PMAI)) as a perovskite additive. It is found that F-PMAI can retard the crystallization process of perovskite film through hydrogen bond interaction between F- and FA+ and reduce (111) facet surface energy due to enhanced adsorption energy of F-PMAI on the (111) facet. Besides, the bulky molecular is extruded to the bottom and top of perovskite film after crystal growth, which can passivate interface defects through strong interaction between F-PMA+ and undercoordinated Pb2+/I-. As a result, the additive facilitates the formation of large perovskite grains and (111) preferred orientation with a reduced trap-state density, thereby promoting charge carrier transportation, and enhancing device performance and stability. The perovskite/silicon TSCs achieved a champion efficiency of 30.05% based on a silicon thin film tunneling junction. In addition, the devices exhibit excellent long-term thermal and light stability without encapsulation. This work provides an effective strategy for achieving efficient and stable TSCs.

Efficient and Bright Deep-Red Light-Emitting Diodes based on a Lateral 0D/3D Perovskite Heterostructure

Bright and efficient deep-red light-emitting diodes (LEDs) are important for applications in medical therapy and biological imaging due to the high penetration of deep-red photons into human tissues. Metal-halide perovskites have potential to achieve bright and efficient electroluminescence due to their favorable optoelectronic properties. However, efficient and bright perovskite-based deep-red LEDs have not been achieved yet, due to either Auger recombination in low-dimensional perovskites or trap-assisted nonradiative recombination in 3D perovskites. Here, a lateral Cs4PbI6/FAxCs1- xPbI3 (0D/3D) heterostructure that can enable efficient deep-red perovskite LEDs at very high brightness is demonstrated. The Cs4PbI6 can facilitate the growth of low-defect FAxCs1- xPbI3, and act as low-refractive-index grids, which can simultaneously reduce nonradiative recombination and enhance light extraction. This device reaches a peak external quantum efficiency of 21.0% at a photon flux of 1.75 × 1021 m-2 s-1, which is almost two orders of magnitude higher than that of reported high-efficiency deep-red perovskite LEDs. Theses LEDs are suitable for pulse oximeters, showing an error <2% of blood oxygen saturation compared with commercial oximeters.

Metal-Halide Perovskite Lasers: Cavity Formation and Emission Characteristics

Hybrid metal-halide perovskites (MHPs) have shown remarkable optoelectronic properties as well as facile and cost-effective processability. With the success of MHP solar cells and light-emitting diodes, MHPs have also exhibited great potential as gain media for on-chip lasers. However, to date, stable operation of optically pumped MHP lasers and electrically driven MHP lasers-an essential requirement for MHP laser's insertion into chip-scale photonic integrated circuits-is not yet demonstrated. The main obstacles include the instability of MHPs in the atmosphere, rudimentary MHP laser cavity patterning methods, and insufficient understanding of emission mechanisms in MHP materials and cavities. This review aims to provide a detailed overview of different strategies to improve the intrinsic properties of MHPs in the atmosphere and to establish an optimal MHP cavity patterning method. In addition, this review discusses different emission mechanisms in MHP materials and cavities and how to distinguish them.

Understanding Defects in Perovskite Solar Cells through Computation: Current Knowledge and Future Challenge

Lead halide perovskites with superior optoelectrical properties are emerging as a class of excellent materials for applications in solar cells and light-emitting devices. However, perovskite films often exhibit abundant intrinsic defects, which can limit the efficiency of perovskite-based optoelectronic devices by acting as carrier recombination centers. Thus, an understanding of defect chemistry in lead halide perovskites assumes a prominent role in further advancing the exploitation of perovskites, which, to a large extent, is performed by relying on first-principles calculations. However, the complex defect structure, strong anharmonicity, and soft lattice of lead halide perovskites pose challenges to defect studies. In this perspective, on the basis of briefly reviewing the current knowledge concerning computational studies on defects, this work concentrates on addressing the unsolved problems and proposing possible research directions in future. This perspective particularly emphasizes the indispensability of developing advanced approaches for deeply understanding the nature of defects and conducting data-driven defect research for designing reasonable strategies to further improve the performance of perovskite applications. Finally, this work highlights that theoretical studies should pay more attention to establishing close and clear links with experimental investigations to provide useful insights to the scientific and industrial communities.

Spatially selective defect management of CsPbI3 films for high-performance carbon-based inorganic perovskite solar cells

Defects formed at the surface, buried interface and grain boundaries (GB) of CsPbI3 perovskite films considerably limit photovoltaic performance. Such defects could be passivated effectively by the most prevalent post modification strategy without compromising the photoelectric properties of perovskite films, but it is still a great challenge to make this strategy comprehensive to different defects spatially distributed throughout the films. Herein, a spatially selective defect management (SSDM) strategy is developed to roundly passivate various defects at different locations within the perovskite film by a facile one-step treatment procedure using a piperazine-1,4-diium tetrafluoroborate (PZD(BF4)2) solution. The small-size PZD2+ cations could penetrate into the film interior and even make it all the way to the buried interface of CsPbI3 perovskite films, while the BF4- anions, with largely different properties from I- anions, mainly anchor on the film surface. Consequently, virtually all the defects at the surface, buried interface and grain boundaries of CsPbI3 perovskite films are effectively healed, leading to significantly improved film quality, enhanced phase stability, optimized energy level alignment and promoted carrier transport. With these films, the fabricated CsPbI3 PSCs based on carbon electrode (C-PSCs) achieve an efficiency of 18.27%, which is among the highest-reported values for inorganic C-PSCs, and stability of 500 h at 85 °C with 65% efficiency maintenance.

Improvement of Thermal Stability and Photoelectric Performance of Cs2PbI2Cl2/CsPbI2.5Br0.5 Perovskite Solar Cells by Triple-Layer Inorganic Hole Transport Materials

Conventional hole transport layer (HTL) Spiro-OMeTAD requires the addition of hygroscopic dopants due to its low conductivity and hole mobility, resulting in a high preparation cost and poor device stability. Cuprous thiocyanate (CuSCN) is a cost-effective alternative with a suitable energy structure and high hole mobility. However, CuSCN-based perovskite solar cells (PSCs) are affected by environmental factors, and the solvents of an HTL can potentially corrode the perovskite layer. In this study, a Co3O4/CuSCN/Co3O4 sandwich structure was proposed as an HTL for inorganic Cs2PbI2Cl2/CsPbI2.5Br0.5 PSCs to address these issues. The Co3O4 layers can serve as buffer and encapsulation layers, protecting the perovskite layer from solvent-induced corrosion and enhancing hole mobility at the interface. Based on this sandwich structure, the photovoltaic performances of the Cs2PbI2Cl2/CsPbI2.5Br0.5 PSCs are significantly improved, with the power conversion efficiency (PCE) increasing from 9.87% (without Co3O4) to 11.06%. Furthermore, the thermal stability of the devices is also significantly enhanced, retaining 80% of its initial PCE after 40 h of continuous aging at 60 °C. These results indicate that the Co3O4/CuSCN/Co3O4 sandwich structure can effectively mitigate the corrosion of the perovskite layer by solvents of an HTL and significantly improves the photovoltaic performance and thermal stability of devices.

Recent Advances in Carbon Nanotube Utilization in Perovskite Solar Cells: A Review

Due to their exceptional optoelectronic properties, halide perovskites have emerged as prominent materials for the light-absorbing layer in various optoelectronic devices. However, to increase device performance for wider adoption, it is essential to find innovative solutions. One promising solution is incorporating carbon nanotubes (CNTs), which have shown remarkable versatility and efficacy. In these devices, CNTs serve multiple functions, including providing conducting substrates and electrodes and improving charge extraction and transport. The next iteration of photovoltaic devices, metal halide perovskite solar cells (PSCs), holds immense promise. Despite significant progress, achieving optimal efficiency, stability, and affordability simultaneously remains a challenge, and overcoming these obstacles requires the development of novel materials known as CNTs, which, owing to their remarkable electrical, optical, and mechanical properties, have garnered considerable attention as potential materials for highly efficient PSCs. Incorporating CNTs into perovskite solar cells offers versatility, enabling improvements in device performance and longevity while catering to diverse applications. This article provides an in-depth exploration of recent advancements in carbon nanotube technology and its integration into perovskite solar cells, serving as transparent conductive electrodes, charge transporters, interlayers, hole-transporting materials, and back electrodes. Additionally, we highlighted key challenges and offered insights for future enhancements in perovskite solar cells leveraging CNTs.

Passivating Defects via Retarding the Reaction Rate of FAI and PbI2 Enables Stable Perovskite Solar Cells

The two-step sequential deposition strategy has garnered widespread usage in the fabrication of high-performance perovskite solar cells based on FAPbI3. However, the rapid reaction between FAI and PbI2 during preparation often leads to incomplete reactions, reducing the device efficiency and stability. Herein, we introduced a multifunctional additive, 2-thiophenyl trifluoroacetone (TTA), into the FAI precursor. The incorporation of TTA has proven to be highly effective in slowing the reaction rate between FAI and PbI2, resulting in increased perovskite formation and improved efficiency and stability of the devices. TTA's CF3 groups interact with FAI via hydrogen bonding, effectively suppressing FA+ defects. The S and C═O groups share lone pair electrons with uncoordinated Pb2+, leading to a reduction in perovskite film defects and suppressing nonradiative recombination. Additionally, the CF3 groups impart hydrophobicity, protecting the perovskite film from moisture-induced erosion. As a result, the TTA-modified perovskite film achieves a Champion efficiency of 23.42% compared to the control's 21.52, with 20.58% efficiency for a 25 cm2 solar module. Remarkably, the unencapsulated Champion device retains 86% of its initial PCE after 1080 h under dark conditions (60 ± 5 °C, 35 ± 5% RH), indicating enhanced long-term stability. These findings offer a promising and cost-effective tactic for high-quality perovskite film fabrication.

High-throughput screening of the transport behavior of tetragonal perovskites

Halide perovskites have attracted attention due to their low cost and excellent optoelectronic properties. Although their optical properties gained widespread consensus, there was still divergence in understanding carrier transport behavior. In this study, the mobility of tetragonal perovskites was investigated by empirical models, including longitudinal acoustic phonon (LAP) and polar optical phonon (POP) models. The results revealed that the mobility predicted from the LAP model was much higher than that from the POP model. A longitudinal optical phonon (LOP) was considered as the decisive scattering source for charge carriers in perovskites. Furthermore, the mobility was extremely sensitive to z-axis strain, and 8 types of perovskites with high carrier mobility were screened. Using the experimental lattice constants, the predicted mobility of CsSnI3 was μe,z = 1428 and μh,z = 2310 cm2 V-1 s-1, respectively. The tetragonal CsSnI3 has high mobility and moderate bandgaps, suggesting potential applications in high-efficiency solar cells.

Unveiling the Potential of Ambient Air Annealing for Highly Efficient Inorganic CsPbI3 Perovskite Solar Cells

Here, we report a detailed surface analysis of dry- and ambient air-annealed CsPbI3 films and their subsequent modified interfaces in perovskite solar cells. We revealed that annealing in ambient air does not adversely affect the optoelectronic properties of the semiconducting film; instead, ambient air-annealed samples undergo a surface modification, causing an enhancement of band bending, as determined by hard X-ray photoelectron spectroscopy measurements. We observe interface charge carrier dynamics changes, improving the charge carrier extraction in CsPbI3 perovskite solar cells. Optical spectroscopic measurements show that trap state density is decreased due to ambient air annealing. As a result, air-annealed CsPbI3-based n-i-p structure devices achieved a 19.8% power conversion efficiency with a 1.23 V open circuit voltage.

Recent Progress of Low-Toxicity Poor-Lead All-Inorganic Perovskite Solar Cells

Organic-inorganic hybrid perovskite solar cells (PSCs) have achieved an impressive certified efficiency of 25.7%, which is comparatively higher than that of commercial silicon solar cells (23.3%), showing great potential toward commercialization. However, the low stability and high toxicity due to the presence of volatile organic components and toxic metal lead in the perovskites pose significant challenges. To obtain robust and low-toxicity PSCs, substituting organic cations with pure inorganic cations, and partially or fully replacing the toxic Pb with environmentally benign metals, is one of the promising methods. To date, continuous efforts have been made toward the construction of highly performed low-toxicity inorganic PSCs with astonishing breakthroughs. This review article provides an overview of recent progress in inorganic PSCs in terms of lead-reduced and lead-free compositions. The physical properties of poor-lead all-inorganic perovskites are discussed to unveil the major challenges in this field. Then, it reports notable achievements for the experimental studies to date to figure out feasible methods for efficient and stable poor-lead all-inorganic PSCs. Finally, a discussion of the challenges and prospects for poor-lead all-inorganic PSCs in the future is presented.

Zirconium Doping to Enable High-Efficiency and Stable CsPbI2Br All-Inorganic Perovskite Solar Cells

All-inorganic wide-bandgap perovskite CsPbI2Br has attracted much attention because of its inherent thermal stability and ideal bandgap for the front subcell of tandem solar cells (TSCs). However, the low power conversion efficiency (PCE) and poor moisture stability of CsPbI2Br still restrict its future commercialization. Herein, zirconium tetrachloride (ZrCl4) was doped into CsPbI2Br films to modulate the crystal growth and improve the film quality. The partial substitution of the B-site Pb2+ of CsPbI2Br with Zr4+ suppresses the unwanted phase conversion from the crystallized black α-phase to the δ-phase, resulting in improved phase stability. Consequently, the humidity and thermal stability of the film are greatly improved. Additionally, the incorporation of ZrCl4 suppresses nonradiative recombination and forms a matched energy-level alignment with the hole-transport layer (Spiro-OMeTAD). Benefiting from these features, the ZrCl4-doped CsPbI2Br perovskite solar cell (PSC) shows an outstanding efficiency of 16.60% with a high open-circuit voltage of 1.29 V. The unencapsulated devices simultaneously show excellent humidity and thermal stability, retaining over 91% of PCEinitial after 1000 h of aging in ambient air conditions and 92% PCEinitial after 500 h of continuous heating at 85 °C in a nitrogen environment, respectively. Furthermore, ZrCl4-doped CsPbI2Br was employed as the front subcell of perovskite/organic TSCs and achieved a remarkable PCE of 19.42%, showing great potential for highly efficient and stable TSCs.

Metal Clusters Based Multifunctional Materials for Solar Cells

As a multifunctional material, metal clusters have recently received some attention for their application in solar cells.This review delves into the multifaceted role of metal clusters in advancing solar cell technologies, covering diverse aspects from electron transport and interface modification to serving as molecular precursors for inorganic materials and acting as photosensitizers in metal-cluster sensitized solar cells (MCSSCs). The studies conducted by various researchers illustrate the crucial impact of metal clusters, such as gold nanoclusters (Au NCs), on enhancing solar cell efficiency through size-dependent effects, distinct interface behaviors, and tailored interface engineering. From optimizing charge transfer rates to improving light absorption and reducing carrier recombination, metal clusters prove instrumental in shaping the landscape of solar energy conversion.The promising performance of metal-cluster sensitized solar cells, coupled with their scalability and flexibility, positions them as a exciting avenue for future clean energy applications. The article concludes by emphasizing the need for continued interdisciplinary research and technological innovation to unlock the full potential of metal clusters in contributing to sustainable and high-performance solar cells.

Defect Passivation and Lithium Ion Coordination Via Hole Transporting Layer Modification for High Performance Inorganic Perovskite Solar Cells

Metal halide inorganic perovskite solar cells (PSCs) have great potential to achieve high efficiency with excellent thermal stability. However, the surface defect traps restrain the achievement of high open circuit voltage (VOC ) and power conversion efficiency (PCE) of the devices due to the severe nonradiative charge recombination. Moreover, the state-of-the-art hole transporting layer (HTL) significantly hampers device moisture stability, even though it renders the highest solar cell efficiency. Herein, a one-stone-two-birds strategy is proposed using a biocompatible material tryptamine (TA) as an additive in HTL. First, TA bearing electron rich moieties can favorably passivate the surface defects of inorganic perovskite films, significantly reducing trap density and prolonging charge lifetime. It results in a drastic improvement of VOC from 1.192 to 1.251 V, with a VOC loss of 0.48 V. The corresponding PSCs achieve a 21.8% PCE under 100 mW cm-2 illumination. Second, TA in HTL can coordinate with lithium cations, retarding their reaction with moisture and increasing the moisture stability of HTL. Consequently, the black phase of inorganic perovskite films is well preserved, and the corresponding PSCs maintain 90% of the initial PCE after 800 h storage at relative humidity of 25-35%, much higher than the control devices.

Deciphering Reaction Products in Formamidine-Based Perovskites with Methylammonium Chloride Additive

The fabrication of formamidinium lead iodide (FAPbI3) perovskite solar cells (PSCs) involves the addition of methylammonium chloride (MACl) to promote low-temperature α-phase formation and grain growth. However, as the added MACl deprotonates and volatilizes into methylamine (MA0) and HCl for removal, MA0 can chemically interact with formamidinium (FA+), forming methyl formamidinium (MFA+) as a byproduct. Despite its significance, the chemical interactions among FAPbI3 perovskites, MACl additives, and their byproducts remain poorly understood. Our findings reveal that the FA+ and MA0 reaction primarily yields a mixture of cis/trans-N-methyl formamidinium iodide (MFAI) isomers, with cis-MFAI prevailing as the dominant species. Moreover, MFAI subsequently reacts with PbI2 to yield fully formed cis-MFAPbI3 2H-phase perovskite. We elucidated the effects of MFAI on the crystal growth, phase stability, and band gap of formamidine-based perovskites through the growth of single crystals. This research offers valuable insights into the role of these byproducts in influencing the efficiency and long-term stability of future PSCs.

Investigation of phase transition, mechanical behavior and lattice thermal conductivity of halogen perovskites using machine learning interatomic potentials

Using a machine learning (ML) approach to fit DFT data, interatomic potentials have been successfully extracted. In this study, the phase transition, mechanical behavior and lattice thermal conductivity are investigated for halogen perovskites using NEP-based MD simulations in a large supercell including 16 000 atoms, which breaks through the size and temperature effects in DFT. A clear phase transition from orthorhombic (γ) → tetragonal (β) → cubic (α) is observed during the heating process. During the cooling process, CsPbCl3 and CsPbBr3 exhibit perfect reversible behavior, while CsPbI3 only undergoes a phase transition from α to β. Then, the key mechanical parameters, including Poisson's ratio, tensile strength, critical strain and bulk modulus, are predicted. The thermal conductivity is also investigated using the NEP-based MD simulations. At room temperature, they exhibit extremely low thermal conductivity. The predicted results are compared with the experimental results, and the rationality of ML potentials has been confirmed.

Thermal annealing promoted room temperature phosphorescence: motion models and internal mechanism

Thermal annealing has been proven to be an efficient method to optimize the device performance of organic and polymeric opto-electronic materials. However, no detailed information of aggregate structures was obtained for a deeper understanding of what happens during thermal annealing. Herein, through modulation of molecular configurations by tunable linkage positions, and the amplified amplitudes of molecular motions by incorporation of additional methylene units, accurate changes of aggregated structures upon thermal annealing have been achieved, accompanying with the 'turn-on' room temperature phosphorescence (RTP) response by about 4800- and 177-fold increase of lifetimes. The stretching and swing motion models have been proposed, which afforded an efficient way to investigate the science of dynamic aggregation in depth.

Controllable Black-to-Yellow Phase Transition by Tuning the Lattice Symmetry in Perovskite Quantum Dots

The black-to-yellow phase transition in perovskite quantum dots (QDs) is more complex than in bulk perovskites, regarding the role of surface energy. Here, with the assistance of in situ grazing-incidence wide-angle and small-angle X-ray scattering (GIWAXS/GISAXS), distinct phase behaviors of cesium lead iodide (CsPbI3 ) QD films under two different temperature profiles-instant heating-up (IHU) and slow heating-up (SHU) is investigated. The IHU process can cause the phase transition from black phase to yellow phase, while under the SHU process, the majority remains in black phase. Detailed studies and structural refinement analysis reveal that the phase transition is triggered by the removal of surface ligands, which switches the energy landscape. The lattice symmetry determines the transition rate and the coexistence black-to-yellow phase ratio. The SHU process allows longer relaxation time for a more ordered QD packing, which helps sustain the lattice symmetry and stabilizes the black phase. Therefore, one can use the lattice symmetry as a general index to monitor the CsPbI3 QD phase transition and finetune the coexistence black-to-yellow phase ratio for niche applications.

Strengthened Surface Modification for High-Performance Inorganic Perovskite Solar Cells with 21.3% Efficiency

Metal halide inorganic perovskites show excellent thermal stability compared to organic-inorganic perovskites. However, the performance of inorganic perovskite solar cells (PSCs) is far from theoretical values, together with unsatisfactory stability, mainly due to the poor interfacial properties. In this work, a facial but effective method is reported to realize high-performance inorganic PSCs by post-modifying the perovskite surface with 2-thiophene ethylamine (TEA). It is found that amine group from TEA can favorably interact with the undercoordinated Pb2+ via Lewis acid-based coordination, while thiophene ring with electron-rich sulfur assists such interaction by functioning as an electron donor. The synergetic interaction allows TEA to passivate perovskite film defects more efficiently, as compared to phenethylamine (PEA) with less electron-donating ability. Moreover, perovskite valence band is slightly upward shift to match with hole transport material and facilitate hole transfer. These combinations result in a reduced non-radiative charge recombination and improved charge carrier lifetime. Consequently, PSCs with TEA modification shows a drastic improvement of VOC by 54 mV, yielding a champion PCE of 21.3%, much higher than the control PSCs (19.3%), along with improved ambient stability. This work demonstrates that surface modifier with an electron-rich moiety is critical for achieving efficient and stable inorganic PSCs.

Discovery of all-inorganic lead-free perovskites with high photovoltaic performance via ensemble machine learning

Growing evidence shows that all-inorganic lead-free perovskites hold promise for solving stability and toxicity problems in perovskite solar cells. However, the power conversion efficiency of all-inorganic perovskites cannot match that of hybrid organic-inorganic perovskites. To face the challenges of efficiency, stability and toxicity simultaneously for application in perovskite solar cells, this study conducts a high-throughput materials search via ensemble machine learning for nearly 12 million all-inorganic perovskites to obtain candidates with non-toxicity and excellent photovoltaic performance. Based on experimental data, models for structure identification and band gap classification are established for , and a physics-inspired multi-component neural network is proposed as part of the exploration of the model's logical structure. It is found that extracting key features for input into the model and treating non-key features as supplements make model learning easier and are more effective in reducing the model parameters. Then, based on established ensemble models as well as the new criteria of ion radius difference and the optimization rules of toxicity and cost, over 80 000 candidates are screened. Among the 34 lead-free identified with suitable band gaps and negative formation energies through first principles calculations, 17 candidates have theoretical power conversion efficiencies over 20%. The Debye temperature of 10 lead-free , basically Bi-based compounds, is greater than 350 K, which is advantageous for suppressing nonradiative recombination and thermally induced degradation.

Surface Termination on Unstable Methylammonium-based Perovskite Using a Steric Barrier for Improved Perovskite Solar Cells

Compared to widely adopted low-dimensional/three-dimensional (LD/3D) heterostructure, functional organic cation based surface termination on perovskite can not only realize advantage of defect passivation but also prevent potential disadvantage of the heterostructure induced intercalation into 3D perovskite. However, it is still very challenging to controllably construct surface termination on organic-inorganic hybrid perovskite because the functional organic cations' substitution reaction is easy to form LD/3D heterostructure. Here, we report using a novel benzyltrimethylammonium (BTA) functional cation with rational designed steric hindrance to effectively surface terminate onto methylammonium lead triiodide (MAPbI3 ) perovskite, which is composed of the most unstable MA cations. The BTA cation is difficult to form a specific 1.5-dimensional perovskite of BTA4 Pb3 I10 by cation substitution with MA cation, which then provides a wide processing window (around 10 minutes) for surface terminating on MAPbI3 films. Moreover, the BTAI surface terminated BTAI-MAPbI3 shows better passivation effect than BTA4 Pb3 I10 -MAPbI3 heterojunction. Finally, BTAI surface terminated solar cell (0.085 cm2 ) and mini-module (11.52 cm2 ) obtained the efficiencies of 22.03 % and 18.57 %, which are among the highest efficiencies for MAPbI3 based ones.

Interface Modification for Energy Level Alignment and Charge Extraction in CsPbI3 Perovskite Solar Cells

In perovskite solar cells (PSCs) energy level alignment and charge extraction at the interfaces are the essential factors directly affecting the device performance. In this work, we present a modified interface between all-inorganic CsPbI3 perovskite and its hole-selective contact (spiro-OMeTAD), realized by the dipole molecule trioctylphosphine oxide (TOPO), to align the energy levels. On a passivated perovskite film, with n-octylammonium iodide (OAI), we created an upward surface band-bending at the interface by TOPO treatment. This improved interface by the dipole molecule induces a better energy level alignment and enhances the charge extraction of holes from the perovskite layer to the hole transport material. Consequently, a Voc of 1.2 V and a high-power conversion efficiency (PCE) of over 19% were achieved for inorganic CsPbI3 perovskite solar cells. Further, to demonstrate the effect of the TOPO dipole molecule, we present a layer-by-layer charge extraction study by a transient surface photovoltage (trSPV) technique accomplished by a charge transport simulation.

Multislip-enabled morphing of all-inorganic perovskites

All-inorganic lead halide perovskites (CsPbX3, X = Cl, Br or I) are becoming increasingly important for energy conversion and optoelectronics because of their outstanding performance and enhanced environmental stability. Morphing perovskites into specific shapes and geometries without damaging their intrinsic functional properties is attractive for designing devices and manufacturing. However, inorganic semiconductors are often intrinsically brittle at room temperature, except for some recently reported layered or van der Waals semiconductors. Here, by in situ compression, we demonstrate that single-crystal CsPbX3 micropillars can be substantially morphed into distinct shapes (cubic, L and Z shapes, rectangular arches and so on) without localized cleavage or cracks. Such exceptional plasticity is enabled by successive slips of partial dislocations on multiple [Formula: see text] systems, as evidenced by atomic-resolution transmission electron microscopy and first-principles and atomistic simulations. The optoelectronic performance and bandgap of the devices were unchanged. Thus, our results suggest that CsPbX3 perovskites, as potential deformable inorganic semiconductors, may have profound implications for the manufacture of advanced optoelectronics and energy systems.

Stabilization of Inorganic Perovskite Solar Cells with a 2D Dion-Jacobson Passivating Layer

Inorganic metal halide perovskites such as CsPbI3 are promising for high-performance, reproducible, and robust solar cells. However, inorganic perovskites are sensitive to humidity, which causes the transformation from the black phase to the yellow δ, non-perovskite phase. Such phase instability has been a significant challenge to long-term operational stability. Here, a surface dimensionality reduction strategy is reported, using 2-(4-aminophenyl)ethylamine cation to construct a Dion-Jacobson 2D phase that covers the surface of the 3D inorganic perovskite structure. The Dion-Jacobson layer mainly grows at the grain boundaries of the perovskite, effectively passivating surface defects and providing favourable interfacial charge transfer. The resulting inorganic perovskite films exhibit excellent humidity resistance when submerged in an aqueous solution (isopropanol:water = 4:1 v/v) and exposed to a 50% humidity air atmosphere. The Dion-Jacobson 2D/3D inorganic perovskite solar cell (PSC) achieves a power conversion efficiency (PCE) of 19.5% with a Voc of 1.197 eV. It retains 83% of its initial PCE after 1260 h of maximum power point tracking under 1.2 sun illumination. The work demonstrates an effective way for stabilizing efficient inorganic perovskite solar cells.

The Effect of the Alkyl Chains of the Alkylammonium Pesudohalide Additives on the Performance of Dion Jacobson Perovskite Solar Cells

Dion-Jacobson perovskite (DJP) films suffer from the high structural disorder and non-compact morphology, leading to inefficient and unstable solar cells (SCs). Here, how the alkyl chains of alkylammonium pseudohalide additives including methylammonium thiocyanate (MASCN) and ethylammonium thiocyanate (EASCN), and propylammonium thiocyanate (PASCN), impact the microstructures, optoelectronic properties and the performance of the solar cells is investigated. These additives substantially improve the structural order and the morphology of the DJP films, yielding more efficient and stable solar cells than the control device. They behave quite differently in modifying the morphological features. Particularly, EASCN outstands the additives in terms of the superior morphology, which is compact and uniform and consists of the largest flaky grains. Consequently, the corresponding device delivers a power conversion efficiency (PCE) of 15.27% and maintains ≈86% of the initial PCE after aging in the air for 182 h. Conversely, MASCN as an additive produces uneven DJP film and the device maintains only 46% of the initial PCE. PASCN as an additive produces the finest grains in the DJP film, and the corresponding device yields a PCE of 11.95%. From the economical point of view, it costs 0.0025 yuan per device for the EASCN additive, allowing for cost-effective perovskite solar cells.

Solvent-antisolvent interactions in metal halide perovskites

The fabrication of metal halide perovskite films using the solvent-engineering method is increasingly common. In this method, the crystallisation of the perovskite layer is triggered by the application of an antisolvent during the spin-coating of a perovskite precursor solution. Herein, we introduce the current state of understanding of the processes involved in the crystallisation of perovskite layers formed by solvent engineering, focusing in particular on the role of antisolvent properties and solvent-antisolvent interactions. By considering the impact of the Hansen solubility parameters, we propose guidelines for selecting the appropriate antisolvent and outline open questions and future research directions for the fabrication of perovskite films by this method.

Built-in Electric Field in Quasi-2D CsPbI3 Perovskites Using High-Polarized Zwitterionic Spacer for Enhanced Charge Separation/Transport

Two-dimensional (2D) halide perovskites are promising candidates for the fabrication of stable and high-efficiency solar cells. However, the low power conversion efficiency (PCE) of cell devices using 2D perovskites is attributed to reduced charge transport caused by poor organic barrier conductivity. In this study, we propose the use of a high-polarized organic zwitterionic spacer, p-aminobenzoic acid (PABA), to construct novel quasi-2D perovskite structures with enhanced self-driven charge separation and transfer. The NH3+ and COO- groups in PABA generate an aligned electric field, promoting carrier separation and aggregation on the opposite edges of the inorganic layer. This enables efficient in-plane transportation along the inorganic layer. Additionally, PABA intercalated quasi-2D perovskite exhibits improved stability compared with counterparts with diamine cation spacers due to the strong interaction between -COO- and inorganic layers. Our findings suggest that high-polarized organic zwitterionic spacers, with NH3+ and COO- functionality, hold promise for stable and efficient quasi-2D perovskite solar cells.

Indoor Photovoltaic Fiber with an Efficiency of 25.53% under 1500 Lux Illumination

Photovoltaic devices represent an efficient electricity generation mode. Integrating them into textiles offers exciting opportunities for smart electronic textiles-with the ultimate goal of supplying power for wearable technology-which is poised to change how electronic devices are designed. Many human activities occur indoors, so realizing indoor photovoltaic fibers (IPVFs) that can be woven into textiles to power wearables is critical, although currently unavailable. Here, a dye-sensitized IPVF is constructed by incorporating titanium dioxide nanoparticles into aligned nanotubes to produce close contact and stable interfaces among active layers on a curved fiber substrate, thus presenting efficient charge transport and low charge recombination in the photoanode. With the combination of highly conductive core-sheath Ti/carbon nanotube fiber as a counter electrode, the IPVF shows a certified power conversion efficiency of 25.53% under 1500 lux illuminance. Its performance variation is below 5% after bending, twisting, or pressing for 1000 cycles. These IPVFs are further integrated with fiber batteries as self-charging power textiles, which are demonstrated to effectively supply electricity for wearables, solving the power supply problem in this important direction.

Towards low-temperature processing of efficient γ-CsPbI3 perovskite solar cells

Inorganic cesium lead iodide (CsPbI3) perovskite solar cells (PSCs) have attracted enormous attention due to their excellent thermal stability and optical bandgap (∼1.73 eV), well-suited for tandem device applications. However, achieving high-performance photovoltaic devices processed at low temperatures is still challenging. Here we reported a new method for the fabrication of high-efficiency and stable γ-CsPbI3 PSCs at lower temperatures than was previously possible by introducing the long-chain organic cation salt ethane-1,2-diammonium iodide (EDAI2) and regulating the content of lead acetate (Pb(OAc)2) in the perovskite precursor solution. We find that EDAI2 acts as an intermediate that can promote the formation of γ-CsPbI3, while excess Pb(OAc)2 can further stabilize the γ-phase of CsPbI3 perovskite. Consequently, improved crystallinity and morphology and reduced carrier recombination are observed in the CsPbI3 films fabricated by the new method. By optimizing the hole transport layer of CsPbI3 inverted architecture solar cells, we demonstrate efficiencies of up to 16.6%, surpassing previous reports examining γ-CsPbI3 in inverted PSCs. Notably, the encapsulated solar cells maintain 97% of their initial efficiency at room temperature and under dim light for 25 days, demonstrating the synergistic effect of EDAI2 and Pb(OAc)2 in stabilizing γ-CsPbI3 PSCs.

Significantly Improved Efficiency and Stability of Pure Tin-Based Perovskite Solar Cells with Bifunctional Molecules

Tin-based perovskite solar cells (TPSCs) have become one of the most prospective photovoltaic materials due to their remarkable optoelectronic properties and relatively low toxicity. Nevertheless, the rapid crystallization of perovskites and the easy oxidization of Sn²⁺ to Sn⁴⁺ make it challenging to fabricate efficient TPSCs. In this work, a piperazine iodide (PI) material with -NH- and -NH₂⁺- bifunctional groups is synthesized and introduced into the PEA_0.1FA_0.9SnI₃-based precursor solution to tune the microstructure, charge transport, and stability of TPSCs. Compared with piperazine (PZ) containing only the -NH- group, the PI additive displays better effects on regulating the microstructure and crystallization, inhibiting Sn²⁺ oxidation and reducing trap states, resulting in an optimal efficiency of 10.33%. This is substantially better than that of the reference device (6.42%). Benefiting from the fact that PI containing -NH- and -NH₂⁺- groups can passivate both positively charged defects and negatively charged halogen defects, unencapsulated TPSCs modified with the PI material can maintain about 90% of their original efficiency after being kept in a N₂ atmosphere for 1000 h, much higher than the value of 47% in reference TPSCs without additives. This work provides a practical method to prepare efficient and stable pure TPSCs.