Tailoring of Novel Azithromycin-Loaded Zinc Oxide Nanoparticles for Wound Healing

Fabrication of novel vildagliptin loaded ZnO nanoparticles for anti diabetic activity

Diabetes mellitus (DM) is a rapidly prevailing disease throughout the world that poses boundless risk factors linked to several health problems. Vildagliptin is the standard dipeptidyl peptidase-4 (DPP-4) inhibitor type of medication that is used for the treatment of diabetes anti-hyperglycemic agent (anti-diabetic drug). The current study aimed to synthesize vildagliptin-loaded ZnO NPs for enhanced efficacy in terms of increased retention time minimizing side effects and increased hypoglycemic effects. Herein, Zinc Oxide (ZnO) nanoparticles (NPs) were constructed by precipitation method then the drug vildagliptin was loaded and drug loading efficiency was estimated by the HPLC method. X-ray diffraction analysis (XRD), UV-vis spectroscopy, FT-IR, scanning electron microscope (SEM), and EDX analysis were performed for the characterization of synthesized vildagliptin-loaded ZnO NPs. The UV-visible spectrum shows a distinct peak at 363 nm which confirms the creation of ZnO NPs and SEM showed mono-dispersed sphere-shaped NPs. EDX analysis shows the presence of desired elements along with the elemental composition. The physio-sorption studies, which used adsorption isotherms to assess adsorption capabilities, found that the Freundlich isotherm model explains the data very well and fits best. The maximum adsorption efficiency of 58.83% was obtained. Further, In vitro, anti-diabetic activity was evaluated by determining the α-amylase and DPP IV inhibition activity of the product formed. The formulation gave maximum inhibition of 82.06% and 94.73% of α-amylase and DPP IV respectively. While at 1000 µg/ml concentration with IC50 values of 24.11 μg/per ml and 42.94 μg/ml. The inhibition of α-amylase can be ascribed to the interactive effect of ZnO NPs and vildagliptin.

Preparation and Characterization of Chitosan/Hydroxypropyl Methylcellulose Temperature-Sensitive Hydrogel Containing Inorganic Salts for Forest Fire Suppression

Effective forest fire suppression remains a critical challenge, necessitating innovative solutions. Temperature-sensitive hydrogels represent a promising avenue in this endeavor. Traditional firefighting methods often struggle to address forest fires efficiently while mitigating ecological harm and optimizing resource utilization. In this study, a novel intelligent temperature-sensitive hydrogel was prepared specially for forest fire extinguishment. Utilizing a one-pot synthesis approach, this material demonstrates exceptional fluidity at ambient temperatures, facilitating convenient application and transport. Upon exposure to elevated temperatures, it undergoes a phase transition to form a solid, barrier-like structure essential for containing forest fires. The incorporation of environmentally friendly phosphorus salts into the chitosan/hydroxypropyl methylcellulose gel system enhances the formation of temperature-sensitive hydrogels, thereby enhancing their structural integrity and firefighting efficacy. Morphological and thermal stability analyses elucidate the outstanding performance, with the hydrogel forming a dense carbonized layer that acts as a robust barrier against the spread of forest fires. Additionally, comprehensive evaluations employing rheological tests, cone calorimeter tests, a swelling test, and infrared thermography reveal the multifaceted roles of temperature-sensitive hydrogels in forest fire prevention and suppression strategies.

Formulation and evaluation of azithromycin-loaded silver nanoparticles for the treatment of infected wounds

Infected wounds pose a significant challenge in healthcare, requiring innovative therapeutic strategies. Therefore, there is a critical need for innovative pharmaceutical materials to improve wound healing and combat bacterial growth. This study examined the efficacy of azithromycin-loaded silver nanoparticles (AZM-AgNPs) in treating infected wounds. AgNPs synthesized using a green method with Quinoa seed extract were loaded with AZM. Characterization techniques, including X-ray Powder Diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM), and Uv-Vis analysis were utilized. The agar diffusion assay and determination of the MIC were used to assess the initial antibacterial impact of the formulations on both MRSA and E. coli. In addition, the antimicrobial, wound-healing effects and histological changes following treatment with the AZM-AgNPs were assessed using an infected rat model. The nanoparticles had size of 24.9 ± 15.2 nm for AgNPs and 34.7 ± 9.7 nm for AZM-AgNPs. The Langmuir model accurately characterized the adsorption of AZM onto the AgNP surface, indicating a maximum loading capacity of 162.73 mg/g. AZM-AgNPs exhibited superior antibacterial properties in vivo and in vitro compared to controls. Using the agar diffusion technique, AZM-AgNPs showed enhanced zones of inhibition against E. coli and MRSA, which was coupled with decreased MIC levels. In addition, in vivo studies showed that AZM-AgNP treated rats had the best outcome characterized by improved healing process, lower bacterial counts and superior epithelialization, compared to the control group. In conclusion, AZM-AgNPs can be synthesized using a green method with Quinoa seed with successful loading of azithromycin onto silver nanoparticles. In vitro and in vivo studies suggest the promising use of AZM-AgNPs as an effective therapeutic agent for infected wounds.

ZnO nanoparticles induced biofilm formation in Klebsiella pneumoniae and Staphylococcus aureus at sub-inhibitory concentrations

Biofilm formation by the pathogenic bacteria generates a serious threat to the public health as it can increase the virulence potential, resistance to drugs, and escape from the host immune response mechanisms. Among the environmental factors that influence the biofilm formation, there are only limited reports available on the role of antimicrobial agents. During the antimicrobial drug administration or application for any purpose, the microbial population can expect to get exposed to the sub-minimum inhibitory concentration (sub-MIC) of the drug which will have an unprecedented impact on microbial responses. Hence, the study has been conducted to investigate the effects of sub-MIC levels of zinc oxide nanoparticles (ZnO NPs) on the biofilm formation of Klebsiella pneumoniae and Staphylococcus aureus. Here, the selected bacteria were primarily screened for the biofilm formation by using the Congo red agar method, and their susceptibility to ZnO NPs was also evaluated. Quantitative difference in biofilm formation by the selected organisms in the presence of ZnO NPs at the sub-MIC level was further carried out by using the microtiter plate-crystal violet assay. Further, the samples were subjected to atomic force microscopy (AFM) analysis to evaluate the properties and pattern of the biofilm modulated under the experimental conditions used. From these, the organisms treated with sub-MIC levels of ZnO NPs were found to have enhanced biofilm formation when compared with the untreated sample. Also, no microbial growth could be observed for the samples treated with the minimum inhibitory concentration (MIC) of ZnO NPs. The results observed in the study provide key insights into the impact of nanomaterials on clinically important microorganisms which demands critical thinking on the antimicrobial use of nanomaterials.

Azithromycin-loaded liposomes and niosomes for the treatment of skin infections: Influence of excipients and preparative methods on the functional properties

The aim of this study was to develop azithromycin (AZT)-loaded liposomes (LP) and niosomes (NS) useful for the treatment of bacterial skin infections and acne. LP based on phosphatidylcholine from egg yolk (EPC) or from soybean lecithin (SPC), and NS composed of sorbitan monopalmitate (Span 40) or sorbitan monostearate (Span 60) were prepared through the thin film hydration (TFH) and the ethanol injection (EI) methods. The formulations were subsequently characterized for their physico-chemical and functional properties. Vesicles prepared through TFH showed higher average sizes than the corresponding formulations obtained by EI. All the vesicles presented adequate encapsulation efficiency and a negative ζ potential, which assured good stability during the storage period (except for LP-SPC). Formulations prepared with TFH showed a more prolonged AZT release than those prepared through EI, due to their lower surface area and multilamellar structure, as confirmed by atomic force microscopy nanomechanical characterization. Finally, among all the formulations, NS-Span 40-TFH and LP-EPC-TFH allowed the highest drug accumulation in the skin, retained the antimicrobial activity and did not alter fibroblast metabolism and viability. Overall, they could ensure to minimize the dosing and the administration frequency, thus representing promising candidates for the treatment of bacterial skin infections and acne.

Design and Self-Assembly of Peptide-Copolymer Conjugates into Nanoparticle Hydrogel for Wound Healing in Diabetes

Background

Delayed wound healing in skin injuries has become a significant problem in clinics, seriously affecting and even threatening life and health. Recently, research interest has increased in developing wound dressings containing bioactive compounds capable of improving outcomes for complex healing needs.

Methods

In this study, Puerarin-loaded nanoparticles (Pue-NPs) were prepared using the cell-penetrating peptide-poly (lactic-co-glycolic acid) (CPP-PLGA) as a drug carrier by the emulsified solvent evaporation method. Then, they were added into poly (acrylic acid) to obtain a self-assembled nanocomposite hydrogels (SANHs) drug delivery system using the co-polymerization method. The particle size, zeta potential, and micromorphology of Pue-NPs were measured; the appearance, mechanical properties, adhesive strength, and biological activity of SANHs were performed. Finally, the potential of SANHs for wound healing was further evaluated in streptozotocin-induced diabetic mice.

Results

Pue-NPs were regularly spherical, with an average particle size of 134.57 ± 1.42 nm and a zeta potential of 2.14 ± 0.78 mV. SANHs was colorless and transparent with a honeycomb-like porous structure and had an excellent swelling ratio (917%), water vapor transmission rate (3077 g·m-2·day-1), mechanical properties (Young's modulus of 18 kPa, elongation at break of 307%), and adhesive strength (15.5 kPa). SANHs exhibited sustained release of Pue over 48h, with a cumulative release of 55.60 ± 6.01%. In vitro tests revealed that the SANHs presented a 92.22% antibacterial rate against Escherichia coli after 4h, and a 61.91% scavenging rate of 1.1-diphenyl-2-trinitrophenylhydrazine (DPPH) radical. In vivo experiments showed that SANHs accelerated wound repair by reducing the inflammatory response at the wound site, promoting angiogenesis, and facilitating epidermal regeneration and collagen deposition.

Conclusion

In conclusion, we successfully prepared SANHs. Our results show that SANHs have excellent performance and improves wound healing in diabetic mice model, indicating that it can be used to develop an effective strategy for the treatment of diabetic wounds.

Tailoring of an anti-diabetic drug empagliflozin onto zinc oxide nanoparticles: characterization and in vitro evaluation of anti-hyperglycemic potential

Diabetes is a serious health issue that can be a great risk factor related to numerous physical problems. A class of drugs "Gliflozin" especially Sodium Glucose Co. Transporter 2 was inhibited by a novel drug, which is known as "empagliflozin". While ZnO nanoparticles (NPs) had considerable promise for combating diabetes, it was employed in the treatment and management of type-2 diabetes mellitus. The new drug empagliflozin was initially incorporated into Zinc Oxide NPs in this study using the surface physio-sorption technique, and the degree of drug adsorption was assessed using the HPLC method. The tailored product was characterized by using the FTIR, EDX, Ultraviolet-Visible, XRD and SEM techniques. With an average particle size of 17 nm, SEM revealed mono-dispersion of NPs and sphere-like form. The Freundlich isotherm model best fits and explains the data for the physio-sorption investigation, which examined adsorption capabilities using adsorption isotherms. The enzymes α-amylase and α-glucosidase, which are involved in the human metabolism of carbohydrates, were used in the in-vitro anti-diabetic assays. It was discovered that the composite showed the highest levels of 81.72 and 92.77% inhibition of -α-amylase and -glucosidase at an absolute concentration of 1000 μg per ml with IC50 values of 30.6 μg per ml and 72 μg per ml.

Probing analysis of Cu-doping on the structural, optical, morphological and magnetic properties of hematite nanoparticles and their antibacterial activity

The present study describes the synthesis of pure and Cu doped α-Fe2O3nanoparticles (with various concentrations of Copper 1, 3, 6, and 9 wt%) by conventional chemical precipitation technique and examines their structural, morphological, optical, magnetic, and antibacterial capabilities. The XRD pattern of pure and Cu-doped α-Fe2O3 nanoparticles exhibit rhombohedral structure and the estimated crystalline sizes were ranged from 39 to 58 nm. It is discovered that the estimated density dislocations linked to the agglomeration/cluster formations diminish when interstitial vacancies are filled with copper. The obtained bandgap from Tauc's plot, 2.07 eV of pure α-Fe2O3 is found to less than Cu doped α-Fe2O3 nanoparticles (2.9-3.4 eV), due to the structural changes and the tailing of localised states into deep bandgap energy levels. The intense blue emission bands (410-490 nm) arised due to the movement of trapped electrons from the donor level to the valance band and broad green emission bands (522-560 nm) are due to deep level CuO defect to the Fe2O3. The fundamental stretching of Fe-O vibrations and the presence of Cu in prepared samples were identified in FTIR and Raman spectra. SEM micrograph shows the uniform distribution of spherical nanoparticles with size ranged from 39 to 61 nm, which is in good accord with XRD studies. Further, the magnetic characteristics of the pure and Cu-doped α-Fe2O3 samples were assessed using a vibrating sample magnetometer (VSM); the ensuing hysteresis loop of the Cu-doped α-Fe2O3 displays weaker ferromagnetic behaviour. In the present investigations, the disc diffusion technique has been used to examine the antibacterial activity. Thus, the results of antibacterial activities demonstrated that at concentrations of 200 and 500 μg/ml of pure and Cu-doped α-Fe2O3 NPs, the highest zone of inhibition was found against gram (+ve) positive bacteria and was followed by the gram (-ve) negative bacteria's.

Cobalt oxide-chitosan based nanocomposites: Synthesis, characterization and their potential pharmaceutical applications

This research aimed to prepare, characterize, and investigate the biological efficacy of chitosan‑cobalt (II) oxide hybrid nanocomposites against a variety of micrograms. Analytical methods, FTIR, SEM, XRD, and EDX, were utilized to thoroughly characterize the produced CS-CoO nanocomposite. In FTIR spectra, the presence of the chitosan peaks in addition to that of CoO at 681 and 558 cm-1 confirmed that CoO molecules interact with the chitosan backbone. Moreover, in the XRD measurements, significantly less chitosan crystallinity was observed. Due to the incorporation of a larger amount of cobalt oxide within the polymer matrix. Applying the Debye-Sherrer calculation, the crystallite size was obviously reduced from 48.24 nm (5 wt %) to 19.27 nm (20 wt %) for the obtained nanocomposites. Furthermore, SEM measurements showed a transformation in the chitosan surface with the physical adsorption of CoO molecules on the surface active sites of chitosan that were visible in SEM graphs. Additionally, EDX determined the amount of Co element within the chitosan, with the sample of 20 wt % weight being found to be 19.26 wt %. The variable dose well-diffusion method was utilized to assess the efficacy of the CS-Co nanocomposite against a wide range of bacteria and fungi. CS - CoO nanocomposite is more effective than chitosan alone as an antibacterial agent against both Gram-positive and Gram-negative bacteria. Moreover, the MTT approach was employed to measure the cytotoxicity based on the cell viability of different cancer cell lines under different UV expositions. The proportion of the destroyed cells elevated due to the easy diffusion of CS - CoO nanocomposite into cancer cells as UV-free anticancer activity. UV exposition has stimulated the anticancer activity, which was attributed to an increase in ROS generation caused by the increased dose of the chitosan and its CS - CoO nanocomposites. Furthermore, the antioxidant capacities of the prepared nano-composites thin films were validated using the DPPH free radical scavenging method and showed good antioxidant activities with the DPPH radical compared with standard vitamin C. It has been noticed that by increasing the content of CoO nanoparticles from 5 to 20 wt %, the biological activity of the prepared nanocomposites was enhanced.

Investigation of the potential roles of adipose stem cells and substances of natural origin in the healing process of E. coli infected wound model in Rats

Skin infections by pathogenic microorganisms are a serious problem due to the potential of dissemination through the bloodstream to various organs causing toxic effects that may be up to mortality. Escherichia coli (E. coli) is one of the most predominant Gram-negative bacterial species present globally with great attention for investigation. The current study is designed to investigate the possible role of adipose tissue-derived stem cells (ADSCs), as well as natural products such as Trichoderma viride (T. viride) extract, Saccharomyces boulardii (S. boulardii) solution in the enhancement of wound healing process in the infected skin with E. coli. Ninety-six female rats were divided into 8 groups (12 animal/group): normal skin, wounded skin, wounded skin infected with E. coli, infected-wounded skin treated by ADSCs, infected-wounded skin treated by T. viride extract, infected-wounded skin treated by S. boulardii solution, infected-wounded skin treated a combination of treatments, infected-wounded skin treated by gentamicin. At day 21 animal weights and bacterial count were detected and compared. Animals were sacrificed and skin from various groups was investigated using a light microscope for sections stained by (hematoxylin eosin, Masson trichrome, and PCNA) as well as transmission electron microscopy. Pro-inflammatory (IL-1β, TNF- α, and IL-13), anti-inflammatory cytokine (IL-4), and antioxidant enzymes (Superoxide dismutase, glutathione, and catalase) were assessed in various groups revealing that ADSCs lightly shift levels of these parameters in various rat groups to regular levels, while administration of T. viride extract, S. boulardii solution, their combination with ADSCs and gentamicin treatment drive the tested cytokines and enzymes to significant levels similar to a normal level where combination therapy gave the best result. The current findings revealed the possibility of using certain natural products as possible substitutes to regularly applied antibiotics with successive protective results in the wound infection model.

Mechanical and radiation shielding characterization of W-based alloys for advanced nuclear unit

The paper aims to investigate the mechanical and radiation shielding properties of two tungsten-based alloys manufactured by powder technology; their features when compared with two standard stainless steel grades for advanced nuclear applications. Multiple measurements were performed to characterize the alloys' structural and mechanical properties. XRD analysis and average surface roughness measurements showed the crystalline and morphological structure of the alloys. Surface microhardness added to the abrasive wear analysis showed the final wear resistance of the selected alloys. In addition, the shielding features against gamma and fast neutrons radiation were calculated. The superior characteristics of W-based alloys manufactured by powder technology make them suitable to be used in advanced nuclear power units.

Recent advances in the synthesis, characterization and biomedical applications of zinc oxide nanoparticles

Zinc oxide nanoparticles (ZnONPs) have become the widely used metal oxide nanoparticles and drawn the interest of global researchers due to their biocompatibility, low toxicity, sustainability and cost-effective properties. Due to their unique optical and chemical properties, it emerges as a potential candidate in the fields of optical, electrical, food packaging and biomedical applications. Biological methods using green or natural routes are more environmentally friendly, simple and less use of hazardous techniques than chemical and/or physical methods in the long run. In addition, ZnONPs are less harmful and biodegradable while having the ability to greatly boost pharmacophore bioactivity. They play an important role in cell apoptosis because they enhance the generation of reactive oxygen species (ROS) and release zinc ions (Zn2+), causing cell death. Furthermore, these ZnONPs work well in conjunction with components that aid in wound healing and biosensing to track minute amounts of biomarkers connected to a variety of illnesses. Overall, the present review discusses the synthesis and most recent developments of ZnONPs from green sources including leaves, stems, bark, roots, fruits, flowers, bacteria, fungi, algae and protein, as well as put lights on their biomedical applications such as antimicrobial, antioxidant, antidiabetic, anticancer, anti-inflammatory, antiviral, wound healing, and drug delivery, and modes of action associated. Finally, the future perspectives of biosynthesized ZnONPs in research and biomedical applications are discussed.

Complexing Properties of Synthesized 1,3,5-Triaza-7-Phosphaadamantane Derivatives Towards Some Lanthanides and Transition Metal Cations With Significant Antimicrobial and Antioxidant Activities

The synthesis of new water-soluble N-alkylated derivatives of 1,3,5-triaza-7-phosphaadamantane is presented. Ru(PPh3)2Cl2 has been used to react with 1-(4-nitrobenzyl)-3,5-triaza-1-azonia-7-phosphaadamantane bromide (PTAR). By using elemental analysis, NMR, and IR spectroscopy, the obtained compounds were identified. The UV-visible absorption spectroscopy has been used to monitor the complexation of various transition metal cations. Studies on conductivity have been utilized to validate the complexes' stoichiometries. Using the disc diffusion method, five bacteria strains were used for the study of the antimicrobial activity of compounds 1-3. All tested pathogens, including M luteus LB 141107, were found to have strong biologic activity against the compounds tested in this study. Additionally, DPPH (2,2-diphenyl-1-picrylhydrazyl) has been tested for its ability to scavenge hydrogen peroxide and free radicals. According to our results, these compounds exhibit excellent radical scavenging properties.

Development and Evaluation of Topical Zinc Oxide Nanogels Formulation Using Dendrobium anosmum and Its Effect on Acne Vulgaris

Zinc oxide nanoparticles have high levels of biocompatibility, a low impact on environmental contamination, and suitable to be used as an ingredient for environmentally friendly skincare products. In this study, biogenically synthesized zinc oxide nanoparticles using Dendrobium anosum are used as a reducing and capping agent for topical anti-acne nanogels, and the antimicrobial effect of the nanogel is assessed on Cutibacterium acne and Staphylococcus aureus. Dendrobium anosmum leaf extract was examined for the presence of secondary metabolites and its total amount of phenolic and flavonoid content was determined. Both the biogenically and chemogenic-synthesized zinc oxide nanoparticles were compared using UV-Visible spectrophotometer, FE-SEM, XRD, and FTIR. To produce the topical nanogel, the biogenic and chemogenic zinc oxide nanoparticles were mixed with a carbomer and hydroxypropyl-methyl cellulose (HPMC) polymer. The mixtures were then tested for physical and chemical characteristics. To assess their anti-acne effectiveness, the mixtures were tested against C. acne and S. aureus. The biogenic zinc oxide nanoparticles have particle sizes of 20 nm and a high-phase purity. In comparison to chemogenic nanoparticles, the hydrogels with biogenically synthesized nanoparticles was more effective against Gram-positive bacteria. Through this study, the hybrid nanogels was proven to be effective against the microbes that cause acne and to be potentially used as a green product against skin infections.

How Combined Macrolide Nanomaterials are Effective Against Resistant Pathogens? A Comprehensive Review of the Literature

Macrolide drugs are among the broad-spectrum antibiotics that are considered as "miracle drugs" against infectious diseases that lead to higher morbidity and mortality rates. Nevertheless, their effectiveness is currently at risk owing to the presence of devastating, antimicrobial-resistant microbes. In view of this challenge, nanotechnology-driven innovations are currently being anticipated for promising approaches to overcome antimicrobial resistance. Nowadays, various nanostructures are being developed for the delivery of antimicrobials to counter drug-resistant microbial strains through different mechanisms. Metallic nanoparticle-based delivery of macrolides, particularly using silver and gold nanoparticles (AgNPs & AuNPs), demonstrated a promising outcome with worthy stability, oxidation resistance, and biocompatibility. Similarly, macrolide-conjugated magnetic NPs resulted in an augmented antimicrobial activity and reduced bacterial cell viability against resistant microbes. Liposomal delivery of macrolides also showed favorable synergistic antimicrobial activities in vitro against resistant strains. Loading macrolide drugs into various polymeric nanomaterials resulted in an enhanced zone of inhibition. Intercalated nanomaterials also conveyed an outstanding macrolide delivery characteristic with efficient targeting and controlled drug release against infectious microbes. This review abridges several nano-based delivery approaches for macrolide drugs along with their recent achievements, challenges, and future perspectives.

Biosynthesis approach of zinc oxide nanoparticles for aqueous phosphorous removal: physicochemical properties and antibacterial activities

In this study, phosphorus (PO43--P) is removed from water samples using zinc oxide nanoparticles (ZnO NPs). These nanoparticles are produced easily, quickly, and sustainably using Onion extracts (Allium cepa) at an average crystallite size of 8.13 nm using the Debye-Scherrer equation in the hexagonal wurtzite phase. The characterization and investigation of bio-synthesis ZnO NPs were carried out. With an initial concentration of 250 mg/L of P, the effects of the adsorbent dose, pH, contact time, and temperature were examined. At pH = 3 and T = 300 K, ZnO NPs achieved the optimum sorption capacity of 84 mg/g, which was superior to many other adsorbents. The isothermal study was found to fit the Langmuir model at a monolayer capacity of 89.8 mg/g, and the kinetic study was found to follow the pseudo-second-order model. The adsorption process was verified to be endothermic and spontaneous by thermodynamic characteristics. As a result of their low cost as an adsorbent and their high metal absorption, ZnO NPs were found to be the most promising sorbent in this investigation and have the potential to be used as effective sorbents for the removal of P from aqueous solutions. The antimicrobial activity results showed that ZnO NPs concentration had greater antibacterial activity than conventional Cefotaxime, which was utilized as a positive control in the inhibitory zone. However, no inhibitory zone was visible in the controlled wells that had been supplemented with onion extract and DMSO.

Cefoperazone rapidly and sensitive quantitative assessment via a validated RP-HPLC method for different dosage forms, in-use stability, and antimicrobial activities

Cefoperazone (Cfz) is a member of the third generation of parenteral cephalosporin antibiotics. It is used on a wide scale in prescribed antibiotic drugs as anti-infection, especially for Gram-negative and also against Gram-positive microorganisms. The current study aimed to find a rapid RP-HPLC method of Cfz analysis with high linearity, repeatability, sensitivity, selectivity, and inexpensive. In our developed method, there is no need to use special chemical reagents, a high percentage of organic solvent, a high flow rate, further guard column. The chromatographic system comprises an ODS column (150 mm × 4.6 mm × 5 μm). The mobile phase was prepared by mixing KH₂PO₄ solution: acetonitrile (80:20) with a flow rate of 1.0 mL/min at detection wavelength 230 nm, at room temperature using injection volume 20 μL. The method manifested a satisfied linearity regression R² (0.9993) with a good repeatability range (0.34-0.92%) with LOD and LOQ; 4.04 μg/mL and 12.24 μg/mL respectively. The method proved its efficiency via system suitability achievement in the robustness and ruggedness conduction according to the validation guidelines. The shorter analysis time makes the method very valuable in quality control to quantify the commercial Cfz in pharmaceutical preparations. This improved HPLC method has been successfully applied for Cfz analysis for Peracef and Peractam vials in our routine finished and stability studies testing laboratories. Additionally, the detection limit of Cfz has been tested in our quality control lab to detect the smallest amount of traces that may be present after the cleaning process of the production machines for cephalosporins preparations. In a precedent for the first time, we were able to use the current analysis method to determine the minimum inhibitory concentration (MIC) and minimum bacteriostatic concentration (MBC). The conventional broth micro-dilution tube method was used to determine MIC at 250 µg/mL and MBC at 125 µg/mL of Cfz against the standard strain of Burkholderia cepacia (B. cepacia) ATCC 25416 as Gram-negative bacteria in vitro.

Biosynthesis approach of copper nanoparticles, physicochemical characterization, cefixime wastewater treatment, and antibacterial activities

The aim of this paper is the green synthesis of copper nanoparticles (Cu NPs) via Quinoa seed extract. X-ray diffraction (XRD) results confirmed the production of the pure crystalline face center cubic system of the Cu NPs with an average crystallite size of 8.41 nm. Infrared spectroscopy (FT-IR) analysis confirmed the capping and stabilization of the Cu NPs bioreduction process. UV visible spectroscopy (UV-Vis). surface plasmon resonance revealed the absorption peak at 324 nm with an energy bandgap of 3.47 eV. Electrical conductivity was conducted assuring the semiconductor nature of the biosynthesized Cu NPs. Morphological analysis was investigated confirming the nano-characteristic properties of the Cu NPs as polycrystalline cubic agglomerated shapes in scanning electron microscopy (SEM) analysis. Transmission electron microscopy (TEM) analysis also was used to assess the cubic shapes at a particle size of 15.1 ± 8.3 nm and a crystallinity index about equal to 2.0. Energy dispersive spectroscopy (EDX) was conducted to investigate the elemental composition of the Cu NPs. As a potential utility of the biosynthesized Cu NPs as nano adsorbents to the removal of the Cefixime (Xim) from the pharmaceutical wastewater; adsorption studies and process parameters were being investigated. The following strategic methodology for maximum Xim removal was conducted to be solution pH 4, Cu NPs dosage 30 mg, Xim concentration 100 mg/L, and absolute temperature 313 K. The maximum monolayer adsorption capacity was 122.9 mg/g according to the Langmuir isothermal model, and the kinetic mechanism was pseudo-second-order. Thermodynamic parameters also were derived as spontaneous chemisorption endothermic processes. Antibacterial activity of the Xim and Xim@Cu NPs was investigated confirming they are highly potent against each Gram-negative and Gram-positive bacterium.

Rapidly, sensitive quantitative assessment of thiopental via forced stability indicating validated RP-HPLC method and its in-use stability activities

Thiopental sodium (Tho) is an intravenous anesthetic. The current study aimed to find a rapid RP-HPLC method of Tho analysis with high linearity, repeatability, sensitivity, selectivity, and inexpensive. In our developed method, there is no need to use special chemical reagents, a high percentage of organic solvent, a high flow rate, or a further guard column. The chromatographic system consists of an ODS column (150 mm × 4.6 mm × 5 μm). The mobile phase was prepared by mixing KH₂PO₄ solution: methanol (40:60) with a flow rate of 1.2 mL/min at a detection wavelength of 230 nm, at room temperature using an injection volume of 10 μL. The method manifested a satisfied linearity regression R² (0.9997) with a good repeatability precision range (0.16-0.47%) with LOD and LOQ; 14.4 μg/mL and 43.6 μg/mL respectively. Additionally, the method proved its efficiency via system suitability achievement in robustness and ruggedness, according to the validation guidelines. The shorter analysis time makes the method very valuable in quality control to quantify the commercial Tho in pharmaceutical preparations. This improved HPLC method has been successfully applied for Tho analysis for Thiopental UP Pharma 500 mg vials and Thiopental Eipico 1.0 g vials in our routine finished and stability studies testing laboratories. Additionally, the detection limit of Tho has been tested in our quality control lab to detect the smallest amount of traces that may be present after the cleaning process of the production machines for cephalosporins preparations. The method has shown positive results for Tho in low-level raw materials and pharmaceutical formulations.

Plant-ZnO nanoparticles interaction: An approach to improve guinea grass (Panicum maximum) productivity and evaluation of the impacts of its ingestion by freshwater teleost fish

We aimed to evaluate the possible effects of the application of zinc oxide nanoparticles [ZnO NPs; 68.96 ± 33.71 nm; at 100 and 500 mg/kg in a soil mixture of the Typic Dystrophic Red Latosol type and sand (2:1 ratio)] in the cultivation of Panicum maximum (until 125 days), using different biomarkers in addition to evaluating the uptake of Zn by the plants. Furthermore, we assessed the possible transfer of ZnO NPs from P. maximum leaves to zebrafish and their potential. Plants cultivated in substrates with ZnO NPs at 500 mg/kg showed reduced germination rate and growth. However, at 100 mg/kg, plants showed higher biomass and productivity, associated with higher Zn uptake, without inducing oxidative and nitrosative stress. Zinc content in zebrafish was not associated with ingesting leaves of P. maximum cultivated in substrate containing ZnCl₂ or ZnO NPs or with genotoxic, mutagenic, and biochemical effects. In conclusion, ZnO NPs (at 100 mg/kg) are promising in the cultivation of P. maximum, and their ingestion by zebrafish did not cause changes in the evaluated biomarkers. However, we recommend that studies with other animal models be conducted to comprehensively assess the ecotoxicological hazard associated with applying ZnO NPs in soil.

Potential ecotoxicity of substrate-enriched zinc oxide nanoparticles to Physalaemus cuvieri tadpoles

Although the ecotoxicological effects of ZnO nanoparticles (ZnO NPs) have already been reported in different taxa, little is known about their impacts on amphibians. Thus, we aimed to evaluate the potential effects of exposure of Physalaemus cuvieri tadpoles to substrates enriched with ZnO NPs (and with its ionic counterpart, Zn+2, ZnCl2 - both at 100 mg/kg) previously used in the cultivation of Panicum maximum (Guinea grass). We showed that although exposure for 21 days did not impact the survival, growth, and development of tadpoles, we noted an increase in the frequency of erythrocyte nuclear abnormalities in the "ZnCl2" and "ZnONP" groups, which was associated with suppression of antioxidant activity in the animals (inferred by SOD and CAT activity and DPPH free radical scavenging capacity). In the tadpoles of the "ZnONP" group, we also noticed a reduction in creatinine and bilirubin levels, alpha-amylase activity, and an increase in alkaline phosphatase activity. But the treatments did not alter the activity of the enzymes lactate dehydrogenase and gamma-glutamyl-transferase and total protein and carbohydrate levels. On the other hand, we report a cholinesterase and hypotriglyceridemic effect in the "ZnCl2" and "ZnONP" groups. Zn bioaccumulation in animals, from ZnO NPs, from Zn+2 released from them, or both, has been associated with causing these changes. Finally, principal component analysis (PCA) and the values of the "Integrated Biomarker Response" index revealed that the exposure of animals to substrates enriched with ZnO NPs caused more pronounced effects than those attributed to its ionic counterpart. Therefore, our study reinforces the need to consider the environmental risks of using these nanomaterials for agricultural purposes for amphibians.

Structural and Tribological Characterization of Carbon and Glass Fabrics Reinforced Epoxy for Bushing Applications Safety

This article investigates the effect of geometrical alternatives for fiber directions on the structural and tribological properties of glass and carbon fibers when molded with epoxy as polymeric composite fabrics for the safety and quality of bushing applications. To confirm the best composite fabric direction, scanning electron microscope and tribological analyses were carried out for the glass and carbon fabrics at horizontal and vertical geometrical alternative orientations. The tribological test was applied using a pin-on-disk tribometer at constant bark velocity of 0.520 m/s against different loads, beginning with 5, 10, 15, and 20 N for the investigated composite samples. The structural measurements demonstrated that the carbon fiber had a high ability to merge with the resin epoxy when compared with the glass fiber. The tribological analysis elucidated that the lower wear volume loss and friction coefficient were obtained when molding the resin epoxy horizontally to the fiber-stacking direction compared with the other vertical direction. Accordingly, the study deduced that the carbon fiber composite material achieves superior wear resistance when molded by resin epoxy horizontally to the direction of tribological wear, which is suitable for several advanced bushing applications.

Nano zinc oxide-functionalized nanofibrous microspheres: A bioactive hybrid platform with antimicrobial, regenerative and hemostatic activities

Bioactive hybrid constructs are at the cutting edge of innovative biomaterials. PLA nanofibrous microspheres (NF-MS) were functionalized with zinc oxide nanoparticles (nZnO) and DDAB-modified nZnO (D-nZnO) for developing inorganic/nano-microparticulate hybrid constructs (nZnO@NF-MS and D-nZnO@NF-MS) merging antibacterial, regenerative, and haemostatic functionalities. The hybrids appeared as three-dimensional NF-MS frameworks made-up entirely of interconnecting nanofibers embedding nZnO or D-nZnO. Both systems achieved faster release of Zn²⁺ than their respective nanoparticles and D-nZnO@NF-MS exhibited significantly greater surface wettability than nZnO@NF-MS. Regarding bioactivity, D-nZnO@NF-MS displayed a significantly greater and fast-killing effect against Staphylococcus aureus. Both nZnO@NF-MS and D-nZnO@NF-MS showed controllable concentration-dependent cytotoxicity to human gingival fibroblasts (HGF) compared with pristine NF-MS. They were also more effective than pristine NF-MS in promoting migration of human gingival fibroblasts (HGF) in the in vitro wound healing assay. Although D-nZnO@NF-MS showed greater in vitro hemostatic activity than nZnO@NF-MS, (blood-clotting index 22.82 ± 0.65% vs.54.67 ±2.32%) both structures exhibited instant hemostasis (0 s) with no blood loss (0 mg) in the rat-tail cutting technique. By merging the multiple therapeutic bioactivities of D-nZnO and the 3D-structural properties of NF-MS, the innovative D-nZnO@NF-MS hybrid construct provides a versatile bioactive material platform for different biomedical applications.

Multifunctional zwitterionic microneedle dressings for accelerated healing of chronic infected wounds in diabetic rat models

Diabetic infected wounds are one of the major threats to public health but traditional wound dressings always have poor therapeutic efficacy influenced by the single treatment principle and limited penetration depth. Herein, we developed a novel kind of multifunctional degradable and removable zwitterionic microneedle dressings that could achieve multi-effective treatment of diabetic chronic wounds with a single dressing application. The substrates of microneedle dressings are composed of zwitterionic polymer polysulfobetaine methacrylate (PSBMA) and photothermal hair particles (HMPs), which can absorb wound exudate, form a barrier to the bacterial environment for the wound and exhibit an excellent photothermal bactericidal effect to promote wound healing. By loading zinc oxide nanoparticles (ZnO NPs) and asiaticoside in needle tips, drugs could diffuse in the wound area as the tips degrade to achieve highly effective antibacterial and anti-inflammatory effects and promote deep wound healing and tissue regeneration. The microneedles (MNs) were applied in diabetic rats with Staphylococcus aureus-infected wounds to demonstrate that the combination of drug and photothermal multi-treatment has accelerated tissue regeneration and collagen deposition and significantly promoted wound healing.

Improving the properties of commercial steel alloys in the industrial/nuclear field by RF plasma carbonitriding

The study investigates the effect of RF plasma on the commercial SS201 and Steel alloys physical, structural and nuclear properties, using an atmosphere of nitrogen (85%) plus acetylene (15%) at 500 W working for 0.5 h. The results were compared with untreated alloys and AISI304L. The study indicated the ability of RF plasma to improve both the mechanical and tribological properties of treated alloys compared to the original commercial alloys and the AISI304L, and achieve good shielding properties for industrial/nuclear applications.

Anti-Tumor Activity of Orally Administered Gefitinib-Loaded Nanosized Cubosomes against Colon Cancer

Gefitinib (GFT) is a tyrosine kinase inhibitor drug used as a first-line treatment for patients with advanced or metastatic non-small cell lung, colon, and breast cancer. GFT exhibits low solubility and hence low oral bioavailability, which restricts its clinical application. One of the most important trends in overcoming such problems is the use of a vesicular system. Cubosomes are considered one of the most important vesicular systems used to improve solubility and oral bioavailability. In this study, GFT cubosomal nanoparticles (GFT-CNPs) were prepared by the emulsification method. The selected formulation variables were analyzed and optimized by full factorial design and response surface methodology. Drug entrapment efficiency (EE%), transmission electron microscopy, particle size, polydispersity index, in vitro release and its kinetics, and the effect of storage studies were estimated. The chosen GFT-CNPs were subjected to further investigations as gene expression levels of tissue inhibitors of metalloproteinases-1 (TIMP-1) and matrix metalloproteinases-7 (MMP-7), colon biomarkers, and histopathological examination of colon tissues. The prepared GFT-CNPs were semi-cubic in shape, with high EE%, smaller vesicle size, and higher zeta potential values. The in vivo data showed a significant decrease in the serum level of embryonic antigen (CEA), carbohydrate antigen 19-9 (CA 19-9), and gene expression level of TIMP-1 and MMP-7. Histopathological examination showed enhancement in cancer tissue and highly decreased focal infiltration in the lamina propria after treatment with GFT-CNPs.

Advances in the Preparation of Nanofiber Dressings by Electrospinning for Promoting Diabetic Wound Healing

Chronic diabetic wounds are one of the main complications of diabetes, manifested by persistent inflammation, decreased epithelialization motility, and impaired wound healing. This will not only lead to the repeated hospitalization of patients, but also bear expensive hospitalization costs. In severe cases, it can lead to amputation, sepsis or death. Electrospun nanofibers membranes have the characteristics of high porosity, high specific surface area, and easy functionalization of structure, so they can be used as a safe and effective platform in the treatment of diabetic wounds and have great application potential. This article briefly reviewed the pathogenesis of chronic diabetic wounds and the types of dressings commonly used, and then reviewed the development of electrospinning technology in recent years and the advantages of electrospun nanofibers in the treatment of diabetic wounds. Finally, the reports of different types of nanofiber dressings on diabetic wounds are summarized, and the method of using multi-drug combination therapy in diabetic wounds is emphasized, which provides new ideas for the effective treatment of diabetic wounds.

Current Research on Zinc Oxide Nanoparticles: Synthesis, Characterization, and Biomedical Applications

Zinc oxide nanoparticles (ZnO-NPs) have piqued the curiosity of researchers all over the world due to their extensive biological activity. They are less toxic and biodegradable with the capacity to greatly boost pharmacophore bioactivity. ZnO-NPs are the most extensively used metal oxide nanoparticles in electronic and optoelectronics because of their distinctive optical and chemical properties which can be readily modified by altering the morphology and the wide bandgap. The biosynthesis of nanoparticles using extracts of therapeutic plants, fungi, bacteria, algae, etc., improves their stability and biocompatibility in many biological settings, and its biofabrication alters its physiochemical behavior, contributing to biological potency. As such, ZnO-NPs can be used as an effective nanocarrier for conventional drugs due to their cost-effectiveness and benefits of being biodegradable and biocompatible. This article covers a comprehensive review of different synthesis approaches of ZnO-NPs including physical, chemical, biochemical, and green synthesis techniques, and also emphasizes their biopotency through antibacterial, antifungal, anticancer, anti-inflammatory, antidiabetic, antioxidant, antiviral, wound healing, and cardioprotective activity. Green synthesis from plants, bacteria, and fungus is given special attention, with a particular emphasis on extraction techniques, precursors used for the synthesis and reaction conditions, characterization techniques, and surface morphology of the particles.

Preparation of zinc oxide nanoparticles using laser-ablation technique: Retinal epithelial cell (ARPE-19) biocompatibility and antimicrobial activity when activated with femtosecond laser

The unusual physical, chemical, and biological features of nanoparticles have sparked considerable attention in the ophthalmological applications. This study reports the synthesis and characterization of zinc oxide nanoparticles (ZnONPs) using laser-ablation at 100 mJ with different ablation times. The synthesized ZnONPs were spherical with an average size of 10.2 nm or 9.8 nm for laser ablation times of 20 and 30 min, respectively. The ZnONPs were screened for their antimicrobial activity against ophthalmological bacteria, methicillin-resistant S. aureus (MRSA) and Pseudomonas aeruginosa. The significant decrease in bacterial growth was observed after treatment with ZnONPs in combination with 400 nm femtosecond laser irradiation. ZnONPs were investigated for their antioxidant activity and biocompatibility towards retinal epithelial cells (ARPE-19). ZnONPs showed moderate antioxidant and free radical scavenging activity. ZnONPs prepared with an ablation time of 20 min were safer and more biocompatible than those prepared with an ablation time of 30 min, which were toxic to ARPE-19 cells with LC₅₀ (11.3 μg/mL) and LC₉₀ (18.3 μg/mL). In this study, laser ablation technique was used to create ZnONPs, and it was proposed that ZnONPs could have laser-activated antimicrobial activity for ophthalmological applications.

A Novel C@Fe@Cu Nanocomposite Loaded with Doxorubicin Tailored for the Treatment of Hepatocellular Carcinoma

High mortality and morbidity rates are related to hepatocellular carcinoma (HCC), which is the most prevalent type of liver cancer. A new vision for cancer treatment and cancer cell targeting has emerged with the application of nanotechnology, which reduces the systemic toxicity and adverse effects of chemotherapy medications while increasing their effectiveness. It was the goal of the proposed work to create and investigate an anticancer C@Fe@Cu nanocomposite (NC) loaded with Doxorubicin (DOX) for the treatment of HCC. Scanning and transmission electron microscopes (SEM and TEM) were used to examine the morphology of the produced NC. The formulation variables (DOX content, C@Fe@Cu NC weight, and stirring speed) were analyzed and optimized using Box-Behnken Design (BBD) and Response Surface Methodology (RSM). Additionally, X-ray diffraction patterns (XRD) and Fourier Transform Infrared (FTIR) were investigated. Doxorubicin and DOX- loaded C@Fe@Cu NC (DOX-C@Fe@Cu NC) were also assessed against HEPG2 cells for anticancer efficacy (Hepatic cancer cell line). The results revealed the formation of C@Fe@Cu NC with a mean size of 7.8 nm. A D-R model with a mean size of 24.1 nm best fits the adsorption behavior of DOX onto the C@Fe@Cu NC surface. DOX-C@Fe@Cu NC has also been demonstrated to have a considerably lower IC50 and higher cytotoxicity than DOX alone in an in vitro investigation. Therefore, DOX-C@Fe@Cu NC is a promising DOX delivery vehicle for the full recovery of HCC.

Development and Characterization of Azithromycin-Loaded Microemulsions: A Promising Tool for the Treatment of Bacterial Skin Infections

In recent years, the treatment of bacterial skin infections has been considered a major healthcare issue due to the growing emergence of antibiotic-resistant strains of Staphylococcus aureus. The incorporation of antibiotics in appropriate nanosystems could represent a promising strategy, able to overcome several drawbacks of the topical treatment of infections, including poor drug retention within the skin. The present work aims to develop microemulsions containing azithromycin (AZT), a broad-spectrum macrolide antibiotic. Firstly, AZT solubility in various oils, surfactants and co-surfactants was assessed to select the main components. Subsequently, microemulsions composed of vitamin E acetate, Labrasol^® and Transcutol^® P were prepared and characterized for their pH, viscosity, droplet size, zeta potential and ability to release the drug and to promote its retention inside porcine skin. Antimicrobial activity against S. aureus methicillin-resistant strains (MRSA) and the biocompatibility of microemulsions were evaluated. Microemulsions showed an acceptable pH and were characterized by different droplet sizes and viscosities depending on their composition. Interestingly, they provided a prolonged release of AZT and promoted its accumulation inside the skin. Finally, microemulsions retained AZT efficacy on MRSA and were not cytotoxic. Hence, the developed AZT-loaded microemulsions could be considered as useful nanocarriers for the treatment of antibiotic-resistant infections of the skin.

Cefotaxime removal enhancement via bio-nanophotocatalyst α-Fe2O3 using photocatalytic degradation technique and its echo-biomedical applications

The present paper evaluates the photocatalytic degradation (PCD) performance of the biofabricated hematite nanoparticles (α-HNPs) for the degradation approach of the Cefotaxime (Cfm). The optimum pH of the solution to achieve the best PCD was found to be 10.5. The kinetics study for the PCD of the Cfm via α-HNPs has been investigated and the reaction was found to be fellow pseudo-first-order at R² = 0.992. The mass loading impact of α-HNPs was investigated and estimated for the maximum degradation of Cfm 0.4 mg/mL. UV–Vis confirmed that α-HNPs had a direct transition bandgap at 3.78 eV at a maximum absorption wavelength of 362 nm with suspension stability for 7 days. The probable mechanism of the Cfm PCD via α-HNPs and the degradation pathway was conducted. The validation of the suspension stability of the α-HNPs (−68.6 ± 11.8 mV) was determined using the zeta potential investigation test. XRD investigation was conducted after Cfm PCD showing an average crystallite size of 27.0 nm. XRD, TEM, SEM, EDX, and FT-IR analyses have been conducted for the α-HNPs before and after Cfm PCD confirming the high efficiency for the reusability of the current biocatalyst α-HNPs for further use. TEM results of the particle sizes of α-HNPs were found at 19.2 ± 4.4 and 20.6 ± 7.4 nm respectively before and after Cfm PCD. The efficiency of the Cfm PCD was found to be 99.1% after 6 h. High potent as an antibacterial agent of α-HNPs was investigated either α-HNPs alone or after its PCD activity against Cfm. The antibacterial activity revealed high sensitivity, especially toward Gram-positive species indicating its promising ability against pathogenic issues. Interestingly, Cfm@α-HNPs showed superior anti-proliferative activity as tested by MTT assay and were able to induce apoptosis in MCF7 and HepG2 cell lines using the flow cytometry technique at 20.7% and 17% respectively. Also, The IC₅₀ of hydrogen peroxide scavenging was estimated and it was manifested that 635.8 and 665.6 μg/mL of α-HNPs before and after the PCD process of Cfm respectively.

Functionalization of Se-Te Nanorods with Au Nanoparticles for Enhanced Anti-Bacterial and Anti-Cancer Activities

The use of medical devices for therapeutic and diagnostic purpose is globally increasing; however, bacterial colonization on therapeutic devices can occur, causing severe infections in the human body. It has become an issue for public health. It is necessary to develop a nanomaterial based on photothermal treatment to kill toxic bacterial strains. Appropriately, high photothermal conversion and low-cost powerful photothermal agents have been investigated. Recently, gold nanocomposites have attracted great interest in biological applications. Here, we prepared rod-shaped Se-Te@Au nanocomposites of about 200 nm with uniform shape and surface-coated with gold nanoparticles for the first time showing high anti-bacterial and anti-cancer activities. Se-Te@Au showed proper structural consistency and natural resistance to bacterial and cancer cells. The strong absorption and high photothermal conversion efficacy made it a good photothermal agent material for the photothermal treatment of bacterial and cancer cells. The Se-Te@Au rod showed excellent anti-bacterial efficacy against Gram-negative Escherichia coli and Gram-positive Staphylococcus aureus, with highest recorded inhibition zones of 25 ± 2 mm and 22 ± 2 mm, respectively. More than 99% of both types of strains were killed after 5 min with a near-infrared (NIR) laser at the very low concentration of 48 µg/mL. The Se-Te@Au rod’s explosion in HeLa cells was extensively repressed and demonstrated high toxicity at 100 µg/mL for 5 min when subjected to an NIR laser. As a result of its high photothermal characteristics, the exceptional anti-bacterial and anti-cancer effects of the Se-Te@Au rod are considerably better than those of other methods previously published in articles. This study could open a new framework for sterilization applications on the industrial level.

Diabetes mellitus and diabetic foot ulcer: Etiology, biochemical and molecular based treatment strategies via gene and nanotherapy

Diabetes mellitus (DM) is a collection of metabolic and pathophysiological disorders manifested with high glucose levels in the blood due to the inability of β-pancreatic cells to secrete an adequate amount of insulin or insensitivity of insulin towards receptor to oxidize blood glucose. Nevertheless, the preceding definition is only applicable to people who do not have inherited or metabolic disorders. Suppose a person who has been diagnosed with Type 1 or Type 2DM sustains an injury and the treatment of the damage is complicated and prolonged. In that case, the injury is referred to as a diabetic foot ulcer (DFU). In the presence of many proliferating macrophages in the injury site for an extended period causes the damage to worsen and become a diabetic wound. In this review, the scientific information and therapeutic management of DM/DFU with nanomedicine, and other related data were collected (Web of Science and PubMed) from January 2000 to January 2022. Most of the articles revealed that standard drugs are usually prescribed along with hypoglycaemic medications. Conversely, such drugs stabilize the glucose transporters and homeostasis for a limited period, resulting in side effects such as kidney damage/failure, absorption/gastrointestinal problems, and hypoglycemic issues. In this paper, we review the current basic and clinical evidence about the potential of medicinal plants, gene therapy, chemical/green synthesized nanoparticles to improving the metabolic profile, and facilitating the DM and DFU associated complications. Preclinical studies also reported lower plasma glucose with molecular targets in DM and DFU. Research is underway to explore chemical/green synthesized nanoparticle-based medications to avoid such side effects. Hence, the present review is intended to address the current challenges, recently recognized factors responsible for DM and DFU, their pathophysiology, insulin receptors associated with DM, medications in trend, and related complications.

Environmentally azithromycin pharmaceutical wastewater management and synergetic biocompatible approaches of loaded azithromycin@hematite nanoparticles

Pharmaceutical wastewater contamination via azithromycin antibiotic and the continuous emergence of some strains of bacteria, cancer, and the Covid-19 virus. Azithromycin wastewater treatment using the biosynthesized Hematite nanoparticles (α-HNPs) and the biocompatible activities of the resulted nanosystem were reported. Biofabrication of α-HNPs using Echinacea purpurea liquid extract as a previously reported approach was implemented. An evaluation of the adsorption technique via the biofabricated α-HNPs for the removal of the Azr drug contaminant from the pharmaceutical wastewater was conducted. Adsorption isotherm, kinetics, and thermodynamic parameters of the Azr on the α-HNPs surface have been investigated as a batch mode of equilibrium experiments. Antibacterial, anticancer, and antiviral activities were conducted as Azr@α-HNPs. The optimum conditions for the adsorption study were conducted as solution pH = 10, 150 mg dose of α-HNPs, and Azr concentration 400 mg/L at 293 K. The most fitted isothermal model was described according to the Langmuir model at adsorption capacity 114.05 mg/g in a pseudo-second-order kinetic mechanistic at R² 0.9999. Thermodynamic study manifested that the adsorption behavior is a spontaneous endothermic chemisorption process. Subsequently, studying the biocompatible applications of the Azr@α-HNPs. Azr@α-HNPs antibacterial activity revealed a synergistic effect in the case of Gram-positive more than Gram-negative bacteria. IC₅₀ of Azr@α-HNPs cytotoxicity against MCF7, HepG2, and HCT116 cell lines was investigated and it was found to be 78.1, 81.7, and 93.4 µg/mL respectively. As the first investigation of the antiviral use of Azr@α-HNPs against SARS-CoV-2, it was achieved a safety therapeutic index equal to 25.4 revealing a promising antiviral activity. An admirable impact of the use of the biosynthesized α-HNPs and its removal nanosystem product Azr@α-HNPs was manifested and it may be used soon as a platform of the drug delivery nanosystem for the biomedical applications.

Fabrication of Zinc loaded silicon carbide Nanocomposite for in vitro cell viability and in vivo wound dressing care

AIM

In this investigation, Zinc-silicon carbide (Zn-SiC) materials were fabricated by a simple approach by using Zn nanoparticles (Zn-NPs) loaded on silicon carbide (SiC) with enhanced antibacterial and healing activity.

METHODS

Zn-NPs loaded on SiC fabricated by the DIY laser melting technique. The TEM and Zeta-sizer confirmed the morphology and size of the nanoparticles. The characterization was done using Fourier transforms infrared spectroscopy (FTIR), and X-ray diffraction (XRD), Thermogravimetric analysis (TGA). Further, the fabricated nanoparticles were evaluated for their mechanical properties and biocompatibility under storage conditions. In-vivo wound healing was measured by observing a percentage reduction in the wound.

RESULTS

Zn-SiC NPs have 54.6 ± 5.25 nm mean particle size, -15.9 ± 2.35 mV zeta potential with 0.187 ± 0.05 polydispersity index (PD1). The nanoparticles showed good biocompatibility and in-vivo wound healing properties.

CONCLUSIONS

These results strongly support the possibility of using these Zn particles loaded on SiC NPs as a promising wound healing agent after cesarean section.

Tolmetin Sodium Fast Dissolving Tablets for Rheumatoid Arthritis Treatment: Preparation and Optimization Using Box-Behnken Design and Response Surface Methodology

Tolmetin sodium (TLM) is a non-steroidal anti-inflammatory drug (NSAIDs). TLM is used to treat inflammation, skeletal muscle injuries, and discomfort associated with bone disorders. Because of the delayed absorption from the gastro intestinal tract (GIT), the currently available TLM dosage forms have a rather protracted start to the effect, according to pharmacokinetic studies. The aim of this study was to create a combination for TLM fast dissolving tablets (TLM-FDT) that would boost the drug's bioavailability by increasing pre-gastric absorption. The TLM-FDTs were developed using a Box-Behnken experimental design with varied doses of crospovidone (CP), croscarmellose sodium (CCS) as super-disintegrants, and camphor as a sublimating agent. In addition, the current study used response surface approach to explore the influence of various formulation and process factors on tablet qualities in order to verify an optimized TLM-FDTs formulation. The optimized TLM-FDTs formula was subsequently evaluated for its in vivo anti-inflammatory activity. TLM-FDTs have good friability, disintegration time, drug release, and wetting time, as well as fast disintegration and dissolution behavior. Significant increase in drug bioavailability and reliable anti-inflammatory efficacy were also observed, as evidenced by considerable reductions in paw thickness in rats following carrageenan-induced rat paw edema. For optimizing and analyzing the effect of super-disintegrants and sublimating agents in the TLM-FDTs formula, the three-factor, three-level full factorial design is a suitable tool. TLM-FDTs are a possible drug delivery system for enhancing TLM bioavailability and could be used to treat rheumatoid arthritis.