Photocatalytic degradation of tetracycline using nanosized titanium dioxide in aqueous solution

Synthesis and characterization of an NH4CL-induced Eskanbil activated carbon (EAC) for the removal of penicillin G from contaminated water

Penicillin G (PG) is one of the most widely used antibiotics around the world. The release of PG in an aqueous solution leads to contamination of water resources. This study aimed to determine the efficiency of modified Eskanbil activated carbon for the removal of PG from aqueous solutions. The NH4Cl-induced activated carbon was synthesized by a simple method and used for the degradation of PG in contaminated water. Activated carbon was characterized by Fourier transform infrared spectroscopy (FTIR), Field emission scanning electron microscopy (FESEM), and Brunauer-Emmett-Teller (BET) surface area analysis. The four main reaction parameters optimized in this study were pH, time, the concentration of the EAC (Eskanbil Activated Carbon), and initial PG concentration. The synthesized carbon was characterized and the results showed it as a mesoporous material with the BET specific surface area of 1473 m²/g and pore volume of 0.81 cm³/g. The maximum PG adsorption onto EAC was observed at the pH of 6. The PG removal of 33% at an EAC concentration of 0.1 g/L increased to 99.98% at an activated carbon concentration of 0.5 g/L. The isotherm and kinetic studies of PG removal by EAC showed that the Freundlich model (R² > 0.995) and the pseudo-second-order (R² > 0.983) equation represented the best fit with the adsorption data. EAC is recommended as a suitable and cost-efficient adsorbent for removing poisons, pharmaceuticals, and other emerging contaminants from water resources.

Photocatalytic degradation of model pharmaceutical pollutant by novel magnetic TiO2@ZnFe2O4/Pd nanocomposite with enhanced photocatalytic activity and stability under solar light irradiation

In the last decades, the use of magnetic nanocomposites as a catalyst was considered for removal of organic pollutants due to its easy separation. Therefore, initially, TiO₂@ZnFe₂O₄/Pd nanocomposite was prepared and then used in the photodegradation of diclofenac under direct solar irradiation in the batch and continuous systems. The structure, morphology and other specifications of produced nanocatalyst were determined via XRD, VSM, FESEM/EDX, FTIR, GTA, UV-Vis, Zeta potential, XPS and ICP-OES. The effective factors on diclofenac removal via nanophotocatalyst viz. pH, catalyst concentration, initial concentration of diclofenac, and flow rate and column length on diclofenac photodegradation were studied. Based on the results, the optimal rate for pH, catalyst concentration, and initial concentration of diclofenac was 4, 0.03 g/l and 10 mg/l respectively. Pd-coated TiO₂@ZnFe₂O₄ magnetic photocatalyst had higher photocatalytic activity in diclofenac photodegradation in relation to ZnFe₂O₄ and TiO₂@ZnFe₂O₄ under solar light irradiation. The findings showed that after five recycles, the photocatalytic efficiency did not show much reduction i.e. the removal efficiency from 86.1% in the first cycle reduced only to 71.38% in the last cycle. Likewise, in this study, with flow rate reduction and column length increase diclofenac degradation rate increased.

Tetracycline Photocatalytic Degradation under CdS Treatment

Industrialization and the growing consumption of medicines leads to global aquatic contamination. One of the antibiotics widely used against bacterial infections in both human and veterinary medicine is tetracycline. Despite its positive antibiotic action, tetracycline is resistant against degradation, and therefore it accumulates in the environment, including the aquatic environment, creating great health hazards, possibly stimulating antibiotic resistance of pathogenic organisms. In this research, aqueous suspensions of semiconductor nanoparticles CdS were used for photocatalytic activity studies in the presence of methylene blue as a model compound, and finally, in the presence of tetracycline, a broad-spectrum antibiotic widely used against bacterial infections, as well as a live-stock food additive. The mechanism and kinetic rate constants of photocatalytic degradation processes of methylene blue and tetracycline were described in correlation with the energy diagram of CdS nanoparticles.

A comprehensive study on the application of FeNi3@SiO2@ZnO magnetic nanocomposites as a novel photo-catalyst for degradation of tamoxifen in the presence of simulated sunlight

Pharmaceutical compounds at trace concentrations are found in the environment, especially in drinking water and food, posing significant negative effects on humans as well as on animals. This paper aimed to examine the diagnostic catalytic properties and efficacy of a novel synthesized photocatalyst, namely FeNi₃@SiO₂@ZnO magnetic nanocomposite, for the removal of tamoxifen (TMX) from wastewater under simulated sunlight. According to the results, it was found that TMX was completely degraded operating under optimized conditions (i.e. pH = 7, catalyst dose = 0.01 g/L, initial TMX concentration = 20 mg/L and reaction time = 60 min). The reaction kinetics of TMX degradation followed a pseudo-first order kinetics model. The final by-products from the TMX photodegradation were water, carbon dioxide, acetic acid, nitroacetic acid methyl ester, 2-methyl-2-pentenal, and 4-methyl-2-pentanol. In addition, the synthesized photocatalyst could successfully performed five consecutive photodegradation cycles. The obtained results revealed that the synthesized FeNi₃@SiO₂@ZnO magnetic nanocomposite holds a great potential to be applied as a photocatalyst for the degradation of TMX on an industrial scale.

The practical utility of the synthesis FeNi3@SiO2@TiO2 magnetic nanoparticles as an efficient photocatalyst for the humic acid degradation

Humic acid (HA) compounds in drinking water and wastewater disinfection processes are viewed as precursors of highly toxic, carcinogenic, and mutagenic disinfection by-product chemicals. In recent times, these compounds have gained considerable attention of scientists for their successful removal from aqueous solutions to permissible limits. To achieve this aim, the present study investigated, for the first time, the photocatalytical performance of the synthesis FeNi₃@SiO₂@TiO₂ nanoparticles for the HA degradation under different environmental conditions. The photocatalytic reactions were performed using ultraviolet (UV) radiation, whose intensity was fixed at 2500 μW/cm² throughout the experimental study. The characterization study performed, using specific diagnostic techniques, revealed the presence of several good morphological, magnetic, and catalytic specifications of the synthesized nanoparticles. The use of the simplified form of the Langmuir-Hinshelwood equation sufficiently describes the experimental data of the HA kinetic degradation, as it shows a high coefficient of regression values. Furthermore, the complete HA degradation was reached under conditions of pH = 3; initial HA concentration = 10 mg/L; FeNi₃@SiO₂@TiO₂ nanoparticles dosage = 0.01 g/L; and reaction time >30 min. Thus, the results obtained from this research suggested that the catalyst of FeNi₃@SiO₂@TiO₂ nanoparticles was an attractive, novel, and effective agent, which could be used for the degradation of HA in the photocatalytic processes.

An overview of photocatalytic degradation: photocatalysts, mechanisms, and development of photocatalytic membrane

Photocatalysis is an ecofriendly technique that emerged as a promising alternative for the degradation of many organic pollutants. The weaknesses of the present photocatalytic system which limit their industrial applications include low-usage of visible light, fast charge recombination, and low migration ability of the photo-generated electrons and holes. Therefore, various elements such as noble metals and transition metals as well as non-metals and metalloids (i.e., graphene, carbon nanotube, and carbon quantum dots) are doped into the photocatalyst as co-catalysts to enhance the photodegradation performance. The incorporation of the co-catalyst which alters the photocatalytic mechanism was discussed in detail. The application of photocatalysts in treating persistent organic pollutants such as pesticide, pharmaceutical compounds, oil and grease and textile in real wastewater was also discussed. Besides, a few photocatalytic reactors in pilot scale had been designed for the effort of commercializing the system. In addition, hybrid photocatalytic system integrating with membrane filtration together with their membrane fabrication methods had also been reviewed. This review outlined various types of heterogeneous photocatalysts, mechanism, synthesis methods of biomass supported photocatalyst, photocatalytic degradation of organic substances in real wastewater, and photocatalytic reactor designs and their operating parameters as well as the latest development of photocatalyst incorporated membrane.

Removal of tetracycline from polluted water by chitosan-olive pomace adsorbing films

This paper focuses on the removal of tetracycline from polluted water by chitosan-olive pomace adsorbing films. More specifically, both raw olive solid wastes (olive pomace) and the olive solid wastes/chitosan composite were compared and used for this purpose. Adsorption capacities values of 16 mg × g^-1 and 1.6 mg × g^-1 were obtained for the two adsorbents respectively. However, chitosan/olive pomace is proposed as suitable for environmental applications avoiding the dispersion of the pomace blocked inside the chitosan film. To detail the adsorption process, the effect of several experimental parameters such as the pH values, ionic strength, amount of adsorbent and pollutant and temperature values was investigated. The results showed that the adsorption process improved increasing the pH values, with a maximum at pH 8, and it was negatively affected by the presence of salts that retarded the adsorption. Indeed, the desorption of tetracycline was obtained in a MgCl₂ 2 M solution. So, a low-cost and cleaner approach, fundamental for the pollutant recovery and for an adsorbent safe reuse, for several cycles of adsorption/desorption, transforming a waste in resource is presented. The kinetics, isotherms models of adsorption and the thermodynamic parameters (ΔG°, ΔH° and ΔS°) were also evaluated observing that the physisorption of the pollutant occurred with and an endothermic character (ΔH° > 0) with ΔG° < 0 and ΔS° > 0. The use of Advanced Oxidation Processes was proposed as possible alternative to the tetracycline recovery, obtaining its degradation after the desorption. With the present paper, the alternative reuse of olive pomace is reported avoiding its disposal in the environment claiming its potential in the removal/recover of emerging contaminants from water.

Photo-Assisted Removal of Tetracycline Using Bio-Nanocomposite-Immobilized Alginate Beads

In the present study, we report an efficient method for tetracycline (TC) removal from contaminated wastewater using alginate beads, immobilized with bio nanocomposite (BNC) consisting of Fe₃O₄ (iron oxide) and TiO₂ (titanium dioxide) nanoparticles along with dead biomass of TC-resistant bacteria Acinetobacter sp. Chemically synthesized Fe₃O₄ nanoparticles and commercially available TiO₂ (P₂₅) nanoparticles were combined to form nanocomposite followed by encapsulation within alginate beads along with heat-killed biomass of Acinetobactersp. for the efficient degradation and adsorption of the target pollutant. The primary characterization of chemically synthesized nanoparticles was carried out with Fourier transform infrared, scanning electron microscopy-energy-dispersive X-ray spectrometry, transmission electron microscopy, and X-ray diffraction techniques. The batch studies for TC removal were performed by varying the reaction parameters such as bead weight, initial TC concentration, and pH in a photoreactor with UV-C irradiation. TC concentration of 10 mg/L, bead weight 10 g, and pH 6 were fixed as the optimum condition where 98 ± 0.5% of TC was removed from the solution. The possible removal mechanism was investigated with the help of UV-visible, total organic carbon, oxidation-reduction potential, Brunauer-Emmett-Teller, and liquid chromatography-mass spectroscopy analyses. The applicability of the process was successfully tested with the natural water systems spiked with TC at 10 mg/L. To assess the ecotoxic effects of the treated effluents, the cell viability assay was performed with the algal strains, Chlorella, and Scenedesmussp. and the bacterial strains, Pseudomonas aeruginosaand Escherichia coli. Finally, the reusability of the BNC bead was successfully established up to the 4th cycle.

Reclamation of grey water for non-potable purposes using pilot-scale solar photocatalytic tubular reactors

Application of pilot-scale slurry-type tubular photocatalytic reactor was tested for the decentralized treatment of actual grey water. The reactors were fabricated by reusing the locally available materials at low cost, operated in batch recycle mode with 25 L of grey water. The influence of operational parameters such as catalysts' concentration, initial slurry pH and addition of H₂O₂ on COD abatement were optimized. The results show that Ag-decorated TiO₂ showed a two-fold increase in COD abatement than did pure TiO₂. Better COD abatement was observed under acidic conditions, and addition of H₂O₂ significantly increases the rate of COD abatement. Within 2 h, 99% COD abatement was observed when the reactor was operated with optimum operational conditions. Silver ion lixiviate was also monitored during the experiment and is five times less than the permissible limits. The catalyst shows good stability even after five cycles without much loss in its photocatalytic activity. The results clearly reveal that pilot-scale slurry tubular solar photocatalytic reactors could be used as a cost-effective method to treat grey water and the resulting clean water could be reused for various non-potable purposes, thus conserving precious water resource. This study favours decentralized grey water treatment and possible scaling up of solar photocatalytic reactor using locally available materials for the potential reuse of treated water.

Intensification of heterogeneous TiO2 photocatalysis using the NETmix mili-photoreactor under microscale illumination for oxytetracycline oxidation

This study focuses on the intensification of heterogeneous TiO₂ photocatalysis for the removal of a contaminant of emerging concern (CEC), oxytetracycline (OTC), as a polishing step of urban wastewaters, using an innovative NETmix mili-photoreactor under UVA-LEDs illumination. The effect of catalyst coated surface per reactor volume and the illumination mechanism, back-side (BSI) or front-side (FSI) irradiation, on OTC oxidation were evaluated. For that, a thin film of photocatalyst was uniformly deposited on the front borosilicate slab (BS) (BSI mechanism; 333 m²_catalyst m^-3_reactor) or on the network of channels and chambers imprinted in the back stainless-steel slab (SSS) (FSI mechanism; 989 m²_catalyst m^-3_reactor) using a spray system. OTC removal was also assessed as a function of TiO₂ film thickness immobilized on both slabs. The photocatalyst reactivity in combination with photoreactor was significantly enhanced (3.4 times) from 0.64 to 2.19 mmol_OTC m^-3_{illuminated reactor volume} s^-1, when considering the BSI and FSI mechanisms, respectively. In addition, the influence of UVA-LEDs intensity on OTC oxidation rate was investigated. UVA-LEDs plates were placed on the top of the NETmix borosilicate window. Moreover, the effect of water matrix was assessed using a secondary effluent from an urban wastewater treatment plant fortified with OTC. OTC oxidation rate was only inhibited in about 1.3 times in the presence of the real matrix, showing the ability of the NETmix to overcome matrix effects due to its unique characteristics. Catalyst film stability over four consecutive reaction cycles was evaluated using synthetic and real matrices fortified with OTC.

Developing boron nitride-pyromellitic dianhydride composite for removal of aromatic pollutants from wastewater via adsorption and photodegradation

A series of boron nitride-pyromellitic dianhydride composites have been successfully synthesized by calcinating the mixtures of boron nitride (BN) and pyromellitic dianhydride (PA) at 350 °C, in which the composite (BNPA2) has the largest adsorption quantity (65.1 mg/g) for rhodamine B (RhB) and the best photo-removal efficiency for RhB under visible light irradiation. ¹H NMR characterizations for BN, PA and BNPA2 suggest that this composite is formed via the reaction between the OH groups in BN and PA. BNPA2 can also adsorb neutral red (NR), methyl orange (MO), tetracycline (TC) and atrazine (AT). NR and MO can be photo-removed by BNPA2 under visible light irradiation. Colorless TC and AT can also be degraded by BNPA2 under visible light irradiation, suggesting that BNPA2 is visible light responsible photocatalyst. BNPA2 has the highest photo-removal efficiency for the cationic RhB and NR, followed by the anionic MO. This is from that BNPA2 has negative surface. When anionic MO mixes with cationic RhB (or NR) together, BNPA2 prefers to remove cationic RhB (or NR) from the mixture solution under visible light irradiation and the removal efficiency of anionic MO by BNPA2 is also increased. Thus, electrostatic interactions between dyes and BNPA2 as well as between dyes play significant role in the removal process. •O^2- makes a main contribution for this photo-removal of these aromatic pollutants (dyes, TC and AT) by BNPA2 under visible light irradiation. Furthermore, the removal performance of BNPA2 for RhB, TC and AT can be effectively regenerated by visible light irradiation.

Review on the treatment of organic pollutants in water by ultrasonic technology

The application of ultrasonic technology in the treatment of organic pollutants in water has attracted more and more attention in recent years. Compared with conventional treatment, ultrasonic treatment is more efficient and time saving. Ultrasonic technology is effective for the degradation of many refractory organic pollutants. In this paper, the principle, influencing factors and various methods of ultrasonic degradation of organic pollutants are studied in view of ultrasonic treatment alone, ultrasound treatment methods combined with biocatalysts, chemical oxidation and adsorption techniques, respectively. In addition, the problems existing in the treatment of organic pollutants in water by ultrasonic technology are analyzed and the development direction is put forward.

Synthesis, characterization and photocatalytic application of Ag-doped Fe-ZSM-5@TiO2 nanocomposite for degradation of reactive red 195 (RR 195) in aqueous environment under sunlight irradiation

BACKGROUND

Most dyes have aromatic rings in their structures, which make them highly toxic for human being and aquatic life. Heterogeneous photodegradation using TiO₂ nanoparticles is one of the most applied methods used for dye removal. The wide band gap of TiO₂ nanoparticles disables its use of the visible light and thus the vast potential of sunlight. To overcome this deficiency, Ag doped TiO₂ nanoparticles were loaded on Fe-ZSM-5.

METHODS

Fe-ZSM-5@TiO₂-Ag photocatalyst was synthesized through sol-gel and hydrothermal methods to remove hazardous Reactive Red 195 (RR 195) from aqueous solution.

RESULTS

Pure phase of Fe-ZSM-5@TiO₂-Ag with specific surface area of 332 m²/g was successfully synthesized. Formation of Ti-O-Ag functional group in the photocatalyst structure confirmed the nanocomposite form of the product. SEM and TEM images portrayed the synthesized zeolite and photocatalyst NPs in a size range of ≤100 nm with homogenous distribution of Ag doped TiO₂ on Fe-ZSM-5 surface. The band-gap energy of Fe-ZSM-5@TiO₂-Ag was calculated 1.97 eV at λ = 630 nm. Photocatalytic activity of the photocatalyst under natural sunlight was investigated through photodecomposition of RR 195 in an aqueous solution. The dye photodecomposition of about 98% was achieved at photocatalyst concentration of 400 mg/L, pH of 3, and dye concentration of 50 mg/L at ambient temperature after 120 min under sunlight using 0.5 ml of TiO₂ and silver ammonium nitrate. The photocatalyst reusability was found significant after 5 frequent cycles.

CONCLUSION

The novel Ag-doped TiO₂-Fe-ZSM-5 nanocomposite with sunlight sensitivity can be a promising candidate to purify wastewater containing organic pollutants.

Synthesis and characterizations of a novel CoFe2O4@CuS magnetic nanocomposite and investigation of its efficiency for photocatalytic degradation of penicillin G antibiotic in simulated wastewater

In the present study, efficiency of a new magnetic nanocomposite (CoFe₂O₄@CuS) for photocatalytic degradation of PG in aqueous solutions was investigated. Structural characteristics of synthesized magnetic nanoparticles were determined by scanning electron microscopy (SEM), transmission electron microscopy (TEM), fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), vibrating-sample magnetometer (VSM), Thermogravimetric analysis (TGA), Brunauer-Emmett-Teller (BET), Energy-dispersive X-ray spectroscopy (EDX) and Raman spectroscopy. Also, the effect of important parameters such as pH (3-11), nanoparticle dosage (0.1-0.8 g/L), PG concentration (10-100 mg/L) and contact time (10-120 min) were investigated. Results of FT-IR, XRD, EDX and Raman analyses showed successful synthesis of CoFe₂O₄@CuS magnetic nanocomposite. SEM and TEM images showed that the size of CoFe₂O₄@CuS magnetic nanocomposite was below 100 nm. Also, results of VSM analyses showed that CoFe₂O₄@CuS magnetic nanocomposite still has magnetic properties (Ms = 7.76 emu/g). According to the results of study, in photocatalytic degradation process of PG by CoFe₂O₄@CuS magnetic nanocomposite by UV light and in optimum condition (pH = 5, nanocomposite dose: 0.2 g/L, PG concentration: 10 mg/L and contact time: 120 min), maximum degradation of PG was 70.7%. Also the photocatalytic reaction almost followed the pseudo-first order kinetics. In addition, after five consecutive runs, the catalyst efficiency wasn't reduced significantly.

Synthesis and characterization of a novel CNT-FeNi3/DFNS/Cu(ii) magnetic nanocomposite for the photocatalytic degradation of tetracycline in wastewater

Herein, Cu(ii) complexes were anchored within the nanospaces of a magnetic fibrous silicate with a high surface area and easily accessible active sites via a facile approach, leading to the successful synthesis of a novel potent nanocatalyst (FeNi₃/DFNS/Cu). Furthermore, FeNi₃/DFNS/Cu was supported on carbon nanotubes (CNTs) via an usual nozzle electrospinning method (CNT-FeNi₃/DFNS/Cu). In addition, its performance as a photocatalyst for the degradation of tetracycline was tested in a batch reactor. Tetracycline is an antibiotic that is commonly utilized in veterinary medicine and in the treatment of human infections, but is hazardous to aquatic environments. However, the usual processes for the removal of tetracycline are not efficient. The eco-friendly attributes of this catalytic system include high catalytic activity and ease of recovery from the reaction mixture using an external magnet, and it can be reused several times without significant loss in its performance. Also, protocols such as hot filtration, and mercury poisoning provided complete insight into the nature of this heterogeneous catalyst.

Herein, Cu(ii) complexes were anchored within the nanospaces of a magnetic fibrous silicate with a high surface area and easily accessible active sites via a facile approach, leading to the successful synthesis of a novel potent nanocatalyst (FeNi₃/DFNS/Cu).

Preparation of Cu2O@TiOF2/TiO2and its photocatalytic degradation of tetracycline hydrochloride wastewater

Cu₂O@TiOF₂/TiO₂composites with large surfaces were prepared by a hydrothermal method and exhibited excellent activity under simulated solar light, showing high efficiency for tetracycline hydrochloride photocatalytic degradation, and reusability.

Dataset for adsorptive removal of tetracycline (TC) from aqueous solution via natural light weight expanded clay aggregate (LECA) and LECA coated with manganese oxide nanoparticles in the presence of H2O2

In this data article, natural (NL) and manganese oxide-modified LECA (MML) adsorbents were applied for adsorptive removal of Tetracycline (TC) from aqueous solution. The used adsorbents was characterized using fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), X-ray diffraction (XRD) and X-ray fluorescence spectroscopy (XRF). The chemical analysis of XRF data revealed increased chemical composition of Mn as MnO to 8.96 wt%. The SEM patterns were illustrated the extent of surface and enhanced porosity in MML with Mn. In optimum operational conditions, maximum removal percentage of TC was achieved at 51.5 and 99.4% using NL and MML, respectively. The maximum adsorption capacities obtained from Langmuir modeling were 6.89 and 9.24 for NL and MML, respectively. The modeling of the adsorption kinetics revealed that TC adsorption by both NL and MML adsorbents was best-fitted with a pseudo-first-order model (R² = 0.978). The isotherm studies of TC adsorption by MML showed that the Freundlich isotherm was the most appropriate model, with a higher coefficient of determination. The obtained data was illustrated that high competitive capacity of chloride and hardness ions compared with other ions against TC adsorption.

Performance of granular ferric hydroxide process for removal of humic acid substances from aqueous solution based on experimental design and response surface methodology

Response surface methodology has been used to design experiments and to optimize the effect of independent variables responsible for higher adsorption of humic acid (HA) by granular ferric hydroxide (GFH) from aqueous solutions. The variables of pH (3–11), contact time (15–120 min), adsorbent dose (1–5 g/L) and initial concentration of humic acid (5–20 mg/L) were examined. The adsorption isotherms and kinetics of humic acid substances on granular ferric hydroxide (GFH) were studied. Also the design of the experiments was performed using R software by the CCD (central composite design) method. Variance analysis (ANOVA) was used as the statistical response analysis method. Result of this study proved the optimal values of the independent variables of the adsorbent dose, contact time, initial concentration of humic acid and pH were 4 g/L, 93.75 min, 16.25 mg/L, and 5, respectively. The experimental data followed the Langmuir isotherm and pseudo-second kinetic model. Based on the response surface methodology, higher HA removal efficiencies were obtained with acidic condition, longer reaction time, and appropriated loading amount of GFH.

Removal of metronidazole by TiO2 and ZnO photocatalysis: a comprehensive comparison of process optimization and transformation products

The photodegradation of antibiotic metronidazole (MNZ) was systematically studied and compared by using aqueous suspensions of TiO₂ and ZnO catalysts under 100-W UV irradiation. The degradation conditions were optimized using the central composite design and response surface methodology. The optimal photodegradation conditions obtained were at pH 6.0 with 1.5 g L^-1 of TiO₂ (86.10% removal for 50 mg L^-1 MNZ) and at pH 9.5 with 0.5 g L^-1 of ZnO (60.32% removal for 30 mg L^-1 MNZ) after 60-min irradiation at 20 °C. The degradation efficiency in the presence of TiO₂ was higher than that of ZnO. The participation of active species such as hydroxyl radicals (OH·), holes (h⁺), and superoxide radicals (O₂^-·) during MNZ photodegradation over TiO₂ and ZnO catalysts was also examined. Experimental results showed that MNZ oxidation was mainly driven by the presence of holes and superoxide radicals. Totally, 10 major intermediates were detected in UV/TiO₂ and UV/ZnO photocatalysis of MNZ using LC-QTof/MS system, in which 5 same intermediates were found. The remaining different intermediates led to the variations of degradation pathways of both processes. Moreover, some bigger transformation products than the parent MNZ were detected.

Degradation of tetracycline in a schorl/H2O2 system: Proposed mechanism and intermediates

Schorl could perform as an extremely promising catalyst for decomposing tetracycline hydrochloride (TC) due to its high degradation efficiency, low cost, chemical stability, easy recovery and repeatable utilization. Comparisons of TC degradation indifferent systems showed that schorl/H₂O₂ system exhibited the optimum pollutant elimination and TOC removal efficiencies. Kinetics and possible mechanisms of TC degradation were clarified. The OH generated on the schorl surface and O₂^-/HO₂ were the main reactive species responsible for TC oxidation. Six possible intermediates were identified, and possible transform mechanisms and pathways were explored. Active radicals were inclined to attack the CC double bond, dimethylamino and phenolic moieties of TC molecular. The principal intermediate products were generated through N-demethylation, oxidation and rearrangement.

Effect of a typical antibiotic (tetracycline) on the aggregation of TiO2 nanoparticles in an aquatic environment

The effect of tetracycline (TC) on the behavior of TiO₂ nanoparticles (NPs) in solution is investigated. The results illustrate that TC molecules do not exhibit an obvious effect on the aggregation of TiO₂ NPs under circumneutral conditions (pH of approximately 5.5). However, the TC molecules exhibit a remarkable effect on the behavior of TiO₂ NPs when the environmental factors (such as pH, ionic strength, and humic acid; HA) are adjusted. In the pH range from 3.0 to 10.0, the zeta potentials of NPs become more positively charged after TC adsorption. The point of zero charge of the TiO₂ NPs increases from 6.5 to 7.5. The stability of the TiO₂ NPs is improved after TC adsorption in different salt solutions. The critical coagulation concentration (CCC) increases from 10.57mmol/L to 17.21mmol/L, 4.95mmol/L to 9.73mmol/L, and 0.23-1.67mmol/L in the presence of NaCl, CaCl₂, and Na₂SO₄ (where Cl^- and SO₄^2- are the counter-ions), respectively. Under different HA concentrations, the C_HAPZC (the HA concentration that causes the zeta potential of NPs to be zero) increases from 0.5mg/L to 1.3mg/L after TC adsorption. The sizes of the TiO₂ NP aggregates are larger than those without TC adsorption. All of these results are due to an increase in the surface charge of the TiO₂ NPs after TC adsorption. The adsorption of H⁺ during TC adsorption causes protonation of the dimethylamine group on the TC molecules.

Role of precursors on the photophysical properties of carbon nitride and its application for antibiotic degradation

In this paper, we provide a comprehensive evaluation of graphitic carbon nitride (C₃N₄) powders derived from the four different precursors melamine, cyanamide, thiourea, and urea for the photocatalytic degradation of tetracycline (TC) antibiotic under sunlight irradiation. The powders were synthesized by employing the conventional thermal decomposition method. The synthesized powders were examined using different characterization tools for evaluating the photophysical properties. The degradation profile revealed that urea-derived C₃N₄ showed the highest activity while melamine-derived C₃N₄ showed the least activity. The TC degradation efficiency of the photocatalyst was found to be influenced more by the surface area values despite extended absorption by melamine in the visible light region. Stability tests on urea-derived C₃N₄ and others were checked by four runs of TC degradation under sunlight irradiation. The synthesized C₃N₄ powders also confirmed the dominance of urea-derived powders for cyclic stability.

Great improvement on tetracycline removal using ZnO rod-activated carbon fiber composite prepared with a facile microwave method

New composite materials of activated carbon fiber (ACF) coated with zinc oxide (ZnO) were obtained by applying a green, cost-effective and rapid synthetic route using a commercial microwave oven. ZnO rods with a uniform and stable structure and an average diameter of 0.3-0.5μm and length of 1.0-1.5μm were achieved after only 3-min microwave treatment. The properties of ZnO were efficiently transferred to ACF, such that the resulting material, termed ZnO rod-ACF, demonstrated a promising potential as an efficient photocatalyst and simultaneously as an adsorbent. Pharmaceutical tetracycline at a concentration of 40mg/L was used to evaluate the organic pollutant removal capacity of the synthesized materials. At pH 8, ZnO rod-ACF exhibited excellent removal capacity (over 99%) and mineralization (90.7%) of tetracycline in aqueous solution within 1h under UV irradiation. The stability of ZnO rod-ACF was maintained and the mineralization of tetracycline was also maintained at 81.35% after multiple usage cycles. The photodegradation pathways of tetracycline were proposed based on the identified reaction intermediates.

An optimized SPE-LC-MS/MS method for antibiotics residue analysis in ground, surface and treated water samples by response surface methodology- central composite design

BACKGROUND

Antibiotic residues are being constantly identified in environmental waters at low concentration. Growing concern has been expressed over the adverse environmental and human health effects even at low concentration. Hence, it is crucial to develop a multi-residues analytical method for antibiotics to generate a considerable dataset which are necessary in the assessment of aquatic toxicity of environmental waters for aquatic organisms and human health. This work aimed to develop a reliable and sensitive multi-residue method based on high performance liquid chromatography coupled with quadrupole-linear ion trap tandem mass spectrometry (HPLC-MS-MS). The method was optimized and validated for simultaneous determination of four classes of antibiotics including, β-lactam, macrolide, fluoroquinolone and nitro-imidazole in treated, ground and surface water matrices.

METHODS

In order to optimize the solid phase extraction process, main parameters influencing the extraction process including, pH, the volume of elution solvent and the amount of Na₄EDTA were evaluated. The optimization of extraction process was carried out by response surface methodology using central composite design. Analysis of variance was performed for nine target antibiotics using response surface methodology.

RESULTS

The extraction recoveries were found to be sensitive to the independent variables of pH, the volume of elution solvent and the amount of Na₄EDTA. The extraction process was pH-dependent and pH was a significant model term in the extraction process of all target antibiotics. Method validation was performed in optimum operation conditions in which the recoveries were obtained in the range of 50-117% for seven antibiotics in spiked treated and ground water samples and for six antibiotics in spiked river water samples. Method validation parameters in terms of method detection limit were obtained in the range of 1-10 ng/L in treated water, 0.8-10 ng/L in the ground water and 0.8-25 ng/L in river water, linearity varied from 0.95 to 0.99 and repeatability in term of relative standard deviation values was achieved less than 10% with the exception for metronidazole and ceftriaxone. The developed method was applied to the analysis of target antibiotics in treated, ground and surface water samples.

CONCLUSIONS

Target antibiotics were analyzed in different water matrices including treated, ground and river water. Seven out of nine antibiotics were detected in Kan River and Firozabad Ditch water samples, although none of them were detected in treated water and ground water samples.

Sonocatalytic degradation of humic acid by N-doped TiO2 nano-particle in aqueous solution

Background

Un-doped and N-doped TiO₂ nano-particles with different nitrogen contents were successfully synthesized by a simple sol–gel method, and were characterized by X-ray diffraction, field emission scanning electron microscopy, Energy dispersive X-ray analysis and UV–visible diffuse reflectance spectra techniques. Then enhancement of sonocatalytic degradation of humic acid by un-doped and N-doped TiO₂ nano-particles in aqueous environment was investigated. The effects of various parameters such as initial concentration of humic acid, N-doping, and the degradation kinetics were investigated.

Results

The results of characterization techniques affirmed that the synthesis of un-doped and N-doped TiO₂ nano-particles was successful. Degradation of humic acid by using different nano-particles obeyed the first-order kinetic. Among various nano-particles, N-doped TiO₂ with molar doping ratio of 6 % and band gap of 2.92 eV, exhibited the highest sonocatalytic degradation with an apparent-first-order rate constant of 1.56 × 10^-2 min⁻¹.

Conclusions

The high degradation rate was associated with the lower band gap energy and well-formed anatase phase. The addition of nano-catalysts could enhance the degradation efficiency of humic acid as well as N-doped TiO₂ with a molar ratio of 6 %N/Ti was found the best nano-catalyst among the investigated catalysts. The sonocatalytic degradation with nitrogen doped semiconductors could be a suitable oxidation process for removal of refractory pollutants such as humic acid from aqueous solution.

Electronic supplementary material

The online version of this article (doi:10.1186/s40201-016-0242-2) contains supplementary material, which is available to authorized users.

Optimization of sonochemical degradation of tetracycline in aqueous solution using sono-activated persulfate process

BACKGROUND

In this study, a central composite design (CCD) was used for modeling and optimizing the operation parameters such as pH, initial tetracycline and persulfate concentration and reaction time on the tetracycline degradation using sono-activated persulfate process. The effect of temperature, degradation kinetics and mineralization, were also investigated.

RESULTS

The results from CCD indicated that a quadratic model was appropriate to fit the experimental data (p < 0.0001) and maximum degradation of 95.01 % was predicted at pH = 10, persulfate concentration = 4 mM, initial tetracycline concentration = 30.05 mg/L, and reaction time = 119.99 min. Analysis of response surface plots revealed a significant positive effect of pH, persulfate concentration and reaction time, a negative effect of tetracycline concentration. The degradation process followed the pseudo-first-order kinetic. The activation energy value of 32.01 kJ/mol was obtained for US/S2O8 (2-) process. Under the optimum condition, the removal efficiency of COD and TOC reached to 72.8 % and 59.7 %, respectively. The changes of UV-Vis spectra during the process was investigated. The possible degradation pathway of tetracycline based on loses of N-methyl, hydroxyl, and amino groups was proposed.

CONCLUSIONS

This study indicated that sono-activated persulfate process was found to be a promising method for the degradation of tetracycline.