Evaluation of advanced oxidation processes for water and wastewater treatment - A critical review

Removal efficiency and energy consumption optimization for carbamazepine degradation in wastewater by electrohydraulic discharge

OBJECTIVE

The treatment of recalcitrant emerging pollutants is a major concern in wastewater treatment. The purpose of this study was the optimization of emerging recalcitrant pollutant degradation using carbamazepine as a representative pollutant. Investigations of the carbamazepine degradation in wastewater was carried out by manipulating discharge current, air flow rate, and initial concentration to maximize removal efficiency and minimize energy consumption.

METHOD

The study utilized a three-factor at two levels factorial design with randomized central runs. Discharge current, air flow rate, and initial concentration were the independent variables while to maximize removal efficiency and minimize energy consumption were the response variables. Analysis of variance (ANOVA) was performed on the data.

RESULTS

Discharge current, air flow rate, and initial concentration significantly impacted the removal efficiency to different degrees. However, for energy consumption, only current and air flow rate were the significant variables. The highest removal efficiency obtained was 93% ± 4% for 10 and 40 mg/L initial carbamazepine concentration after 10 min of plasma treatment at a current of 0.45 A and no air flow rate.

CONCLUSION

The plasma reactor demonstrated the capability to treat high cyclic organic chemical contaminant concentration in wastewater with possible applications in preconcentrated wastewater remediation. However, there is still room for reactor design optimization. One key area of focus is reducing treatment cost, which may be achieved theoretically, pending further experimental investigation, by introducing an alternating current power supply, which can reduce energy consumption by 50%-60%.

PRACTITIONER POINTS

Discharge current, air flow rate, and initial concentration all influenced the removal efficiency of carbamazepine. For energy consumption, only current and air flow rate were significant variables. Higher currents result in an improved highly reactive species and UV generation. Treatment cost per m3 for the plasma reactor is higher than established technologies. The plasma reactor in the study still requires significant optimization.

An overview of biogenic metallic nanoparticles for water treatment and purification: the state of the art

The environment is fundamental to human existence, and protecting it from dangerous contaminants should be a top priority for all stakeholders. Reducing garbage output has helped, but as the world's population grows, more waste will be generated. Tons of waste inadvertently and advertently received by environmental matrixes adversely affect the sustainable environment. The pollution caused by these activities affects the environment and human health. Conventional remediation processes ranging from chemical, physical, and biological procedures use macroaggregated materials and microorganisms to degrade or remove pollutants. Undesirable limitations of expensiveness, disposal challenges, maintenance, and formation of secondary contaminants abound. Additionally, multiple stages of treatments to remove different contaminants are time-consuming. The need to avoid these limitations and shift towards sustainable approaches brought up nanotechnology options. Currently, nanomaterials are being used for environmental rejuvenation that involves the total degradation of pollutants without secondary pollution. As nanoparticles are primed with vast and modifiable reactive sites for adsorption, photocatalysis, and disinfection, they are more useful in remediating pollutants. Review articles on metallic nanoparticles usually focus on chemically synthesized ones, with a particular focus on their adsorption capacity and toxicities. Therefore, this review evaluates the current status of biogenic metallic nanoparticles for water treatment and purification.

Critical State of the Art of Sugarcane Industry Wastewater Treatment Technologies and Perspectives for Sustainability

The worldwide pressure on water resources is aggravated by rapid industrialization, with the food industry, particularly sugar factories, being the foremost contributor. Sugarcane, a primary source of sugar production, requires vast amounts of water, over half of which is discharged as wastewater, often mixed with several byproducts. The discharge of untreated wastewater can have detrimental effects on the environment, making the treatment and reuse of effluents crucial. However, conventional treatment systems may not be adequate for sugarcane industry effluent treatment due to the high organic load and variable chemical and mineral pollution. It is essential to explore pollution-remediating technologies that can achieve a nexus (water, energy, and food) approach and contribute to sustainable development. Based on the extensive literature, membrane technologies such as the membrane bioreactor have shown promising results in treating sugarcane industry wastewater, producing treated water of higher quality, and the possibility of biogas recovery. The byproducts generated from this treatment can also be recovered and used in agriculture for food security. To date, membrane technologies have demonstrated successful results in treating industrial wastewater. This critical review aims to evaluate the performance of traditional and conventional processes in order to propose sustainable perspectives. It also serves to emphasize the need for further research on operating conditions related to membrane bioreactors for valuing sugarcane effluent, to establish it as a sustainable treatment system.

Dual-bionic superwetting gears with liquid directional steering for oil-water separation

Developing an effective and sustainable method for separating and purifying oily wastewater is a significant challenge. Conventional separation membrane and sponge systems are limited in their long-term usage due to weak antifouling abilities and poor processing capacity for systems with multiple oils. In this study, we present a dual-bionic superwetting gears overflow system with liquid steering abilities, which enables the separation of oil-in-water emulsions into pure phases. This is achieved through the synergistic effect of surface superwettability and complementary topological structures. By applying the surface energy matching principle, water and oil in the mixture rapidly and continuously spread on preferential gear surfaces, forming distinct liquid films that repel each other. The topological structures of the gears facilitate the overflow and rapid transfer of the liquid films, resulting in a high separation flux with the assistance of rotational motion. Importantly, this separation model mitigates the decrease in separation flux caused by fouling and maintains a consistently high separation efficiency for multiple oils with varying densities and surface tensions.

Bisphenols in water: Occurrence, effects, and mitigation strategies

Bisphenols (bisphenol A (BPA), bisphenol S (BPS), bisphenol F (BPF) and bisphenol AF (BPAF)) are widely used as additives in numerous industries and therefore they are ubiquitously present throughout the world's natural environment including water. A review of the literature is presented on their sources, pathways of entry into the environment, and especially aquatic contexts, their toxicity to humans and other organisms and the technologies for removing them from water. The treatment technologies used are mostly adsorption, biodegradation, advanced oxidation, coagulation, and membrane separation processes. In the adsorption process, several adsorbents, especially carbon-based materials, have been tested. The biodegradation process has been deployed and it involves a variety of micro-organisms. Advanced oxidation processes (AOPs) such as UV/O₃-based, catalysis relevant AOPs, electrochemical AOPs and physical AOPs have been employed. Both the biodegradation process and AOPs generate by-products which may be toxic. These by-products need to be subsequently removed using other treatment processes. Effectiveness of the membrane process varies depending on the porosity, charge, hydrophobicity, and other properties of the membrane. The problems and limitations of each treatment technique are discussed and methods to overcome them are presented. Suggestions are articulated to use a combination of processes to improve the removal efficiencies.

Insight into Chinese medicine residue biochar combined with ultrasound for persulfate activation in atrazine degradation: Acanthopanax senticosus precursors, synergistic effects and toxicity assessment

The synergistic activation of persulfate by multiple factors could degrade pollutants more efficiently. However, the co-activation method based on metal ions has the risk of leakage. The non-metallic coupling method could achieve the same efficiency as the metal activation and meanwhile release environmental stress. In this study, the original biochar (BC) was prepared through using Chinese medicinal residue of Acanthopanax senticosus as the precursor. Compared with other biochar, the pore size structure was higher and toxicity risk was lower. The ultrasonic (US)/Acanthopanax senticosus biochar (ASBC)/persulfate oxidation system was established for Atrazine (ATZ). Results showed that 45KHz in middle and low frequency band cooperated with ASBC600 to degrade nearly 70 % of ATZ within 50 min, and US promoted the formation of SO₄^- and OH. Meanwhile, the synergy index of US and ASBC was calculated to be 1.18, which showed positive synergistic effect. Finally, the potential toxicity was examined by using Toxicity Characteristic Leaching Procedure (TCLP) and luminescent bacteria. This study provides a promising way for the activation of persulfate, which is expected to bring a new idea for the win-win situation of pollutant degradation and solid waste resource utilization.

Characterization of UV/chlorine process for micropollutant abatement by probe compound-based kinetic models

Micropollutant (MP) abatement efficiencies are critical information for optimizing water treatment process for cost-effective operations. Nevertheless, due to the vast number of MPs in real water matrices, it is infeasible to measure their abatement efficiencies individually in practical applications. In this study, a probe compound-based kinetic model was developed for generalized prediction of MP abatement in various water matrices by the ultraviolet (UV)/chlorine process. The results show that by measuring the depletion of three probe compounds (ibuprofen, primidone, and dimetridazole) spiked in the water matrix, the exposures of main reactive chlorine species (RCS including chlorine radicals (Cl•), dichloride radicals (Cl₂^-•) and chlorine oxide radicals (ClO•)) and hydroxyl radicals (•OH) during the UV/chlorine process could be calculated using the model. Based on the determined exposures, the abatement efficiencies of various MPs in different water matrices (e.g., surface water, groundwater, and wastewater) could generally be predicted with acceptable accuracy by the model without prior water-specific calibration. In addition, the relative contribution of UV photolysis and oxidation with active chlorine, RCS, and •OH to MP abatement could be quantitatively simulated using the model to clarify the abatement mechanism of MPs during the UV/chlorine process. The probe-based kinetic model can thus offer a useful tool to guide practical water and wastewater treatment for MP abatement and to explore the mechanism of UV/chlorine process.

Efficient degradation of micropollutants in CoCaAl-LDO/peracetic acid (PAA) system: An organic radical dominant degradation process

As a novel strategy, peracetic acid (PAA) based advanced oxidation processes (AOPs) are being used in micropollutant elimination due to their high oxidation and low toxicity. In this study, Co₂Ca₁Al₁-LDO as a kind of layered double oxides (LDOs) was successfully synthesized, and it is the first time to apply Co₂Ca₁Al₁-LDO for activating PAA. The Co₂Ca₁Al₁-LDO/PAA system showed excellent removal efficiencies for various micropollutants with removal ratios ranging from 90.4% to 100% and k values from 0.087 min^-1 to 0.298 min^-1. In the degradation period, various reactive oxygen species (ROS) are involved in the system, while organic radicals (R-O^•) with a high concentration of 5.52 × 10^-13 M are the dominant ROS in the contaminants degradation process. Compared to other ROS, R-O^• had the largest contribution ratio (more than 85%) to pollutant degradation. Further analysis demonstrated that C1, C2, C3, C4, C5, C6 and N11 concentrated on the aniline group of SMX are the main attack sites based on the density functional theory (DFT) results, which is consistent with the degradation products. The toxicity of contaminants was obviously reduced after removing in this system. Furthermore, Co₂Ca₁Al₁-LDO showed good reusability and stability, and Co₂Ca₁Al₁-LDO/PAA system had excellent removal ability in actual water bodies containing inorganic anions, showing good application potential. Importantly, this study explored the feasibility of applying LDO catalysts in PAA-based AOPs for micropollutants elimination, providing new insights for subsequent research.

Copper Nanowire Networks: An Effective Electrochemical Peroxymonosulfate Activator toward Nitrogenous Pollutant Abatement

Herein, we developed an electrochemical filtration system for effective and selective abatement of nitrogenous organic pollutants via peroxymonosulfate (PMS) activation. Highly conductive and porous copper nanowire (CuNW) networks were constructed to serve simultaneously as catalyst, electrode, and filtration media. In one demonstration of the CuNW network's capability, a single pass through a CuNW filter (τ < 2 s) degraded 94.8% of sulfamethoxazole (SMX) at an applied potential of -0.4 V vs SHE. The exposed {111} crystal plane of CuNW triggered atomic hydrogen (H*) generation on sites, which contributed to effective PMS reduction. Meanwhile, with the involvement of SMX, a Cu-N bond was formed by the interactions between the -NH₂ group of SMX and the Cu sites of CuNW, accompanied by the redox cycling of Cu²⁺/Cu⁺, which was facilitated by the applied potential. The different charges of the active Cu sites made it easier to withdraw electrons and promote PMS oxidation. Theoretical calculations and experimental results were combined to suggest a mechanism for pollution abatement with CuNW networks. The results showed that system efficacy for the degradation of a wide array of nitrogenous pollutants was robust across a broad range of solution pH and complex aqueous matrices. The flow-through operation of the CuNW filter outperformed conventional batch electrochemistry due to convection-enhanced mass transport. This study provides a new strategy for environmental remediation by integrating state-of-the-art material science, advanced oxidation processes, and microfiltration technology.

Reductive Photodegradation of 4,4'-Isopropylidenebis(2,6-dibromophenol) on Fe3O4 Surface

BACKGROUND

Advanced Oxidation Processes (AOPs) are the water treatment techniques that are commonly used forthe decomposition of the non-biodegradable organic pollutants. However, some pollutants are electron deficient and thus resistant to attack by reactive oxygen species (e.g., polyhalogenated compounds) but they may be degraded under reductive conditions. Therefore, reductive methods are alternative or supplementary methods to the well-known oxidative degradation ones.

METHODS

In this paper, the degradation of 4,4'-isopropylidenebis(2,6-dibromophenol) (TBBPA, tetrabromobisphenol A) using two Fe₃O₄ magnetic photocatalyst (F1 and F2) is presented. The morphological, structural and surface properties of catalysts were studied. Their catalytic efficiency was evaluated based on reactions under reductive and oxidative conditions. Quantum chemical calculations were used to analyse early steps of degradation mechanism.

RESULTS

The studied photocatalytic degradation reactions undergo pseudo-first order kinetics. The photocatalytic reduction process follows the Eley-Rideal mechanism rather than the commonly used Langmuir-Hinshelwood mechanism.

CONCLUSIONS

The study confirms that both magnetic photocatalyst are effective and assure reductive degradation of TBBPA.

Degradation of micropollutants in flow-through VUV/UV reactors: Impact of internal diameter and baffle allocation

Application of VUV/UV process for micropollutants removal in decentralized water supply systems (e.g., rural drinking water treatment) is promising while few researches by far paid attention to the performance of practical flow-through reactors. This study investigated the degradation of atrazine (ATZ), sulfamethoxazole (SMX) and metoprolol (MET) under different hydrodynamic conditions in reactors with varied internal diameters and baffle allocations. Results showed that the target micropollutants could be degraded efficiently in the flow-through VUV/UV reactors following basically the pseudo-first order kinetics (R² ≥ 0.97). The largest degradation rate constants were found in the D35 reactor and incorporation of baffles in the D50 and D80 reactors accelerated obviously the micrpollutants degradation. The improved performances of the baffled reactors were due mainly to the elevated utilization of HO^•, and a new parameter named UE_HO (HO^• utilization efficiency) was proposed accordingly. The calculated UE_HO values of the reactors ranged between 30.2% and 69.2% with the largest found in the D50-5 reactor. This testified the usually insufficient utilization of radicals in flow-through reactors and the effectiveness of baffle implementation. Electrical energy per order (E_EO) values of micropollutants degradation in the reactors were in the range of 0.104-0.263 kWh m^-3 order^-1. The degradation was inhibited significantly by high-concentration nitrate yet the formed nitrite concentration stayed consistently below the drinking water limitation. The acute toxicity of the micropollutant solutions increased first and leveled off afterwards during the VUV/UV treatment, as indicated by the inhibition ratios of luminescence intensity of Vibrio fischeri.

Optimized photodegradation of palm oil agroindustry waste effluent using multivalent manganese-modified black titanium dioxide

This article presents a methodological approach to use manganese (Mn³⁺Mn⁷⁺)-modified black titanium dioxide (Mn/BTiO₂) as a photocatalyst to optimize and improve visible-light-driven photodegradation of treated agro-industrial effluent (TPOME). A modified wet chemical process was used to prepare BTiO₂. The BTiO₂ was then wet impregnated with Mn and calcined at 300 °C for 1 h to produce Mn/BTiO₂. The activity of Mn/BTiO₂ was investigated in terms of photo-assisted elimination of chemical oxygen demand (COD), phenolic compounds (PCs), color, and total organic carbon (TOC). Using the design of experiments (DOE), the conditions of the photocatalytic process, including photocatalyst loading, Mn concentration, hydrogen peroxide (H₂O₂) dose, and irradiation time, were optimized. Under the optimum conditions (0.85 g/L photocatalyst loading, 0.048 mol/L H₂O₂ dose, 0.301 wt.% Mn concentration, and 204 min irradiation time) COD, PCs, color, and TOC removal efficiencies of 88.87%, 86.04%, 62.8%, and 84.66%, respectively, were obtained. Statistical analysis showed that the response variable's removal from TPOME estimation had high R² and low RMSE, MSE, MAD, MAE, and MAPE values, indicating high reliability. This study demonstrated the significant potential of the developed photocatalytic system for the treatment of waste effluent generated by the palm oil industry and other agro-industries, with the ability to simultaneously reduce a number of organic pollution indicators (OPIs).

Performance evaluation of the UV activated chlorite process on trimethoprim: Degradation efficiency, energy consumption and disinfection by-products formation

As the primary inorganic by-product species of ClO₂, chlorite is believed to have negative toxicological effects on human health and therefrom greatly limits the wide application of ClO₂ in water treatment. The synergistic trimethoprim (TMP) removal concerning degradation efficiency, energy consumption and disinfection by-products (DBPs) formation in the UV activated chlorite process accompanied by the simultaneously elimination of chlorite was comprehensively evaluated. UV/chlorite integrated process removed TMP far more rapidly than UV (1.52%) or chlorite (3.20%) alone due to the endogenous radicals (Cl•, ClO• and •OH), the contributing proportions of which were 31.96%, 19.20% and 44.12%. The second-order rate constants of TMP reaction with Cl•, ClO• and •OH were determined to be 1.75 × 10¹⁰, 1.30 × 10⁹ and 8.66 × 10⁹ M^-1 s^-1. The effects of main water parameters including chlorite dosage, UV intensity, pH as well as water matrixes (nature organic matter, Cl^- and HCO₃^-) were examined. k_obs obeyed the order as UV/Cl₂>UV/H₂O₂≈UV/chlorite>UV, and the cost ranking via electrical energy per order (EE/O, kWh m^-3 order^-1) parameter was UV/chlorite (3.7034) > UV/H₂O₂ (1.1625) >UV/Cl₂ (0.1631). The operational scenarios can be optimized to achieve the maximum removal efficiencies and the minimum energy costs. The destruction mechanisms of TMP were proposed by LC-ESI-MS analysis. The overall weighted toxicity in subsequent disinfection was assessed as UV/Cl₂>UV/chlorite > UV, the values of which in post-chlorination were 6.2947, 2.5806 and 1.6267, respectively. Owing to the vital roles of reactive chlorine species (RCS), UV/chlorite displayed far higher TMP degradation efficiency than UV, and concurrently presented much less toxicity than UV/Cl₂. In an effort to determine the viability of the promising combination technology, this study was devoted to reduce and reuse chlorite and synchronously realize the contaminants degradation efficiently.

The performance and mechanism of iron-mediated chemical oxidation: Advances in hydrogen peroxide, persulfate and percarbonate oxidation

Many studies have successfully built iron-mediated materials to activate or catalyze Fenton-like reactions, with applications in water and wastewater treatment being investigated. However, the developed materials are rarely compared with each other regarding their performance of organic contaminant removal. In this review, the recent advances of Fenton-like processes in homogeneous and heterogeneous ways are summarized, especially the performance and mechanism of activators including ferrous iron, zero valent iron, iron oxides, iron-loaded carbon, zeolite, and metal organic framework materials. Also, this work mainly compares three O-O bond containing oxidants including hydrogen dioxide, persulfate, and percarbonate, which are environmental-friendly oxidants and feasible for in-situ chemical oxidation. The influence of reaction conditions, catalyst properties and benefits are analyzed and compared. In addition, the challenges and strategies of these oxidants in applications and the major mechanisms of the oxidation process have been discussed. This work can help understand the mechanistic insights of variable Fenton-like reactions, the role of emerging iron-based materials, and provide guidance for choosing appropriate technologies when facing real-world water and wastewater applications.

Efficient utilization of free radicals in advanced oxidation processes under high-gravity environment for disposing pollutants in effluents and gases: A critical review

Advanced oxidation processes (AOPs) using strongly oxidizing radicals are promising for wastewater treatment and gas purification. Nevertheless, the short half-life of radicals and the limited mass transfer in traditional reactors cause under-utilization of radicals and low pollutant removal efficiency. High-gravity technology (HiGee)-enhanced AOPs (HiGee-AOPs) have been demonstrated a promising way to enhance radical utilization in a rotating packed bed reactor (RPB). Here, we review the potential mechanisms of intensified radical utilization in HiGee-AOPs, structures and performance of RPB, and applications of HiGee in AOPs. The intensification mechanisms are described from three aspects: enhanced generation of radicals by efficient mass transfer, in-situ radical utilization under frequent liquid film renewal, and selective effect on radical utilization due to micromixing in RPB. Based on these mechanisms, we propose a novel High-gravity flow reaction with the essence of efficiency, in-situ, and selectivity in order to better explain the strengthening mechanisms in HiGee-AOPs. HiGee-AOPs possess great potential for treating effluent and gaseous pollutants due to characteristics of High-gravity flow reaction. We discuss the pros and cons of different RPBs and their applications to specific HiGee-AOPs. HiGee improve the following AOPs: (1) facilitate interfacial mass transfer in homogeneous AOPs, (2) enhance mass transfer to expose more catalytically active sites and mass-produce nanocatalysts for heterogeneous AOPs, (3) inhibit bubble accumulation on the electrode surface of electrochemical AOPs, (4) increase the mass transfer between liquid and catalysts in UV-assisted AOPs, (5) improve the micromixing efficiency of ultrasound-based AOPs. Strategies outlined in this paper should inspire further development of HiGee-AOPs.

Valorization of Fibrous Plant-Based Food Waste as Biosorbents for Remediation of Heavy Metals from Wastewater-A Review

Mobilization of heavy metals in the environment has been a matter of concern for several decades due to their toxicity for humans, environments, and other living organisms. In recent years, use of inexpensive and abundantly available biosorbents generated from fibrous plant-based food-waste materials to remove heavy metals has garnered considerable research attention. The aim of this review is to investigate the applicability of using fibrous plant-based food waste, which comprises different components such as pectin, hemicellulose, cellulose, and lignin, to remove heavy metals from wastewater. This contribution confirms that plant-fiber-based food waste has the potential to bind heavy metals from wastewater and aqueous solutions. The binding capacities of these biosorbents vary depending on the source, chemical structure, type of metal, modification technology applied, and process conditions used to improve functionalities. This review concludes with a discussion of arguments and prospects, as well as future research directions, to support valorization of fibrous plant-based food waste as an efficient and promising strategy for water purification.

Mn(VII) enhanced by CaSO3 to remove trace organic pollutants in high salt organic wastewater: Further enhancement of salinity

The high concentration of salt in organic wastewater has a strong inhibitory effect on the removal of pollutants. A method for the efficient removal of trace pollutants in high-salinity organic wastewater was developed. This study investigated the effect of the combination of permanganate [Mn(VII)] and calcium sulfite [S(IV)] on pollutant removal in hypersaline wastewater. The Mn(VII)-CaSO₃ system removed more pollutants from high-salinity organic wastewater than from normal-salinity wastewater. Chloride (increasing from 1 M to 5 M) and low concentration of sulfate (increasing from 0.05 M to 0.5 M) significantly enhanced the system's resistance to pollutants under neutral conditions. Despite the fact that Cl^- can combine with the free radicals in the system and reduce their efficiency in removing pollutants, the presence of chloride ions greatly enhances the electron transfer rate in the system, promoting the conversion of Mn(VII) to Mn(III) and significantly increasing the reaction rate of Mn(III) as the primary active species. Therefore, chloride salts can greatly enhance the removal of organic pollutants by Mn(VII)-CaSO₃. Although sulfate does not react with free radicals, a high concentration of sulfate (1 M) will affect the formation of Mn(III), which greatly weakens the removal effect of the entire system on pollutants. The system can still have a good pollutant removal effect with mixed salt. Altogether, this study demonstrates that the Mn(VII)-CaSO₃ system offers new possibilities for the treatment of organic pollutants in hypersaline wastewater.

Gamma Radiation Synthesis of Ag/P25 Nanocomposites for Efficient Photocatalytic Degradation of Organic Contaminant

Titanium dioxide (TiO₂) has garnered significant attention among various photocatalysts, whereas its photocatalytic activity is limited by its wide bandgap and inefficient charge separation, making the exploration of new strategies to improve its photocatalytic performance increasingly important. Here, we report the synthesis of Ag/P25 nanocomposites through a one-step gamma-ray radiation method using AgNO₃ and commercial TiO₂ (Degussa P25). The resulting products were characterized by powder X-ray diffraction, UV-Vis diffused reflectance spectroscopy, transmission electron microscopy, and X-ray photoelectron spectroscopy. The effect of free radical scavengers, feed ratios of Ag/P25, and dose rates on the photocatalytic activity of the Ag/P25 nanocomposites were systematically investigated using rhodamine B under Xenon light irradiation. The results showed that the Ag/P25 photocatalyst synthesized with a feed ratio of 2.5 wt% and isopropyl alcohol as the free radical scavenger at a dose rate of 130 Gy/min exhibited outstanding photocatalytic activity, with a reaction rate constant of 0.0674 min^-1, much higher than that of P25. Additionally, we found that the particle size of Ag could be effectively controlled by changing the dose rate, and the Ag/P25 nanocomposites doped with smaller size of Ag nanoparticles performed higher photocatalytic activities. The synthesis strategy presented in this study offers new insight into the future development of highly efficient photocatalysts using radiation techniques.

A review of hybrid enzymatic-chemical treatment for wastewater containing antiepileptic drugs

Epilepsy is one of the most common neurological diseases worldwide and requires treatment with antiepileptic drugs for many years or for life. This fact leads to the need for constant production and use of these compounds, placing them among the four pharmaceutical classes most found in wastewater. Even at low concentrations, antiepileptics pose risks to human and environmental health and are considered organic contaminants of emerging concern. Conventional treatments have shown low removal of these drugs, requiring advanced and innovative approaches. In this context, this review covers the results and perspectives on (1) consumption and occurrence of antiepileptics in water, (2) toxicological effects in aquatic ecosystems, (3) enzymatic and advanced oxidation processes for degrading antiepileptics drugs from a molecular point of view (biochemical and chemical phenomena), (4) improvements in treatment efficiency by hybridization, and (5) technical aspects of the enzymatic-AOP reactors.

Alkyl halide formation from degradation of carboxylic acids in the presence of Fe(III) and halides under light irradiation

Advanced oxidation processes (AOPs) have been widely used in water and wastewater treatment and have shown excellent performance in remediating contaminated water. However, their oxidation byproducts, including halogenated organics, have recently attracted increasing attention. Alkyl halides are among the most important environmental pollutants in nature. Here, we report a Fenton-like reaction in which alkyl halides can form during the photodegradation of aliphatic carboxylic acids in the presence of Fe(III) and halides. Chloromethane, chloroethane, and 1-chloropropane were produced from the degradation of acetic acid, propionic acid and n-butyric acid, respectively. CH₃Cl, CH₂Cl₂ and CHCl₃ were all identified as the products of acetic acid with the yields of approximately 5.1%, 0.2% and 0.005%, respectively. It was demonstrated that hydroxyl radicals, halogen radicals and alkyl radicals were involved in the formation of alkyl halides. A possible mechanism of chloromethane formation was proposed based on the results. In real samples of saline water, the addition of carboxylic acid and Fe(III) significantly promoted the generation of CH₃Cl under xenon lamp irradiation. The results indicated that the coexistence of Fe(III), halides and carboxylic acids enhanced the photochemical release of alkyl halides. The reactions described in this paper may contribute to knowledge on the mechanism of halogenated byproduct formation during AOPs.

Advanced treatment of industrial wastewater by ozonation with iron-based monolithic catalyst packing: From mechanism to application

An Fe-based catalyst was prepared by oxidising waste Fe shavings directly in a solution. In engineering applications, Fe shavings were compressed and modified to form Fe-based monolithic catalyst packing. Both of which exhibited excellent catalytic activity in catalytic ozonation industrial wastewater after biochemical treatment. Fe-based monolithic catalyst packing has irregular channels, large porosity, small pore diameter, and the effective specific surface area (SSA) up to 3500 m²/m³, these characteristics are conducive to mass transfer, and promote the effective utilisation of •OH in the catalyst "action zone". A tower reactor (<3000 m³/d) and reinforced concrete construction reactor (>5000 m³/d) were designed according to the wastewater flow. Regression analysis showed that hydraulic residence time (HRT) and O₃/COD_in are important parameters in engineering design and operation. In addition, strategies for the application of Fe-based monolithic catalyst packing to wastewater with high salinity and high inorganic carbon concentration have been proposed. Fe-based monolithic catalyst packing catalytic ozonation is a relatively cost-effective and eco-friendly process with extremely broad application prospects in the advanced treatment of industrial wastewater.

Source preventing mechanism of florfenicol resistance risk in water by VUV/UV/sulfite advanced reduction pretreatment

To avoid the inhibition of microbial activity and the emergence of bacterial resistance, effective abiotic pretreatment methods to eliminate the antibacterial activity of target antibiotics before the biotreatment system for antibiotic-containing wastewater are necessary. In this study, the VUV/UV/sulfite system was developed as a pretreatment technique for the source elimination of florfenicol (FLO) resistance risk. Compared with the VUV/UV/persulfate and sole VUV photolysis, the VUV/UV/sulfite system had the highest decomposition rate (0.33 min^‒1) and the highest defluorination (83.0%), resulting in the efficient elimination of FLO antibacterial activity with less than 2.0% mineralization, which would effectively retain the carbon sources for the sludge microorganisms in the subsequent biotreatment process. Furthermore, H• was confirmed to play a more important role in the elimination of FLO antibacterial activity by controlling the environmental conditions for the formation and transformation of reactive species and adding their scavengers. Based on the theoretical calculation and proposed photolytic intermediates, the elimination of FLO antibacterial activity was achieved by dechlorination, defluorination and removal of sulfomethyl groups. When the pretreated FLO-containing wastewater entered the biological treatment unit, the abundance of associated antibiotic resistance genes (ARGs) and the relative abundance of integrons were efficiently prevented by approximately 55.4% and 22.9%, respectively. These results demonstrated that the VUV/UV/sulfite system could be adopted as a promising pretreatment option for the source elimination of FLO resistance risk by target decomposition of its responsible structures before the subsequent biotreatment process.

Mechanistic and quantitative profiling of electro-Fenton process for wastewater treatment

Electro-Fenton (EF) process represents an energy-efficient and scalable advanced oxidation technology (AOT) for micropollutants removal in wastewaters. However, mechanistic profiling and quantitation of contribution of each subprocess (i.e., adsorption at electrode, coagulation, radical oxidation, electrode oxidation/reduction, and H₂O₂ oxidation) to the overall degradation are substantially unclear, resulting in difficulty in tunability and optimization for different treatment scenarios. In this study, we investigated degradation kinetics of a target micropollutant in an EF system. The contribution of all possible subprocesses was elucidated by comparing the observed degradation rate in the EF system with the sum of the kinetics in each subprocess. The results indicated that the overall degradation can be attributed to the synergistic action of the above-mentioned subprocesses. The radical oxidation accounts for 87% elimination, followed by electrode reoxidation/reduction of 7.7%. These results not only advance the fundamental understanding of synergistic effect in EF system, but also open new possibilities to optimize these techniques for better scalability. In addition, the methodology in this study could potentially boost the in-depth exploration of subprocess contribution in other Fenton-like systems.

Photocatalytic Synthesis of Hydrogen Peroxide from Molecular Oxygen and Water

Hydrogen peroxide is a powerful and green oxidant that allows for the oxidation of a wide span of organic and inorganic substrates in liquid media under mild reaction conditions, and forms only molecular water and oxygen as end products. Hydrogen peroxide is therefore used in a wide range of applications, for which the well-documented and established anthraquinone autoxidation process is by far the dominating production method at the industrial scale. As this method is highly energy consuming and environmentally costly, the search for more sustainable synthesis methods is of high interest. To this end, the article reviews the basis and the recent development of the photocatalytic synthesis of hydrogen peroxide. Different oxygen reduction and water oxidation mechanisms are discussed, as well as several kinetic models, and the influence of the main key reaction parameters is itemized. A large range of photocatalytic materials is reviewed, with emphasis on titania-based photocatalysts and on high-prospect graphitic carbon nitride-based systems that take advantage of advanced bulk and surface synthetic approaches. Strategies for enhancing the performances of solar-driven photocatalysts are reported, and the search for new, alternative, photocatalytic materials is detailed. Finally, the promise of in situ photocatalytic synthesis of hydrogen peroxide for water treatment and organic synthesis is described, as well as its coupling with enzymes and the direct in situ synthesis of other technical peroxides.

Tungsten disulfide (WS2) is a highly active co-catalyst in Fe(III)/H2O2 Fenton-like reactions for efficient acetaminophen degradation

The most important factor that restricts the decomposition of H₂O₂ in the Fe³⁺/H₂O₂ reaction is the slow cycling efficiency of reducing Fe³⁺ to Fe²⁺. In this study, the addition of tungsten disulfide (WS₂) as a co-catalyst achieved a rapid cycling of the reaction rate-limiting step and a significant enhancement of H₂O₂ decomposition, which resulted in the effective degradation of acetaminophen (APAP). Results show that 99.6% of APAP (5 mg L^-1) could be degraded by H₂O₂/Fe³⁺/WS₂ system within 2.5 min. The conversion of Fe³⁺ to Fe²⁺ occurred mainly on the surface of WS₂ due to the redox reaction of the exposed W⁴⁺ active sites with Fe³⁺ after the unsaturated S atoms were bound to protons. Electron paramagnetic resonance (EPR) and radical quenching experiments evaluated the contribution of hydroxyl radical (•OH) and superoxide radical (O₂^•-) in the degradation of pollutants. WS₂ showed good recoverability after four cycles of the reaction. This study provides a new perspective to improve the efficiency of Fe³⁺/H₂O₂ and provides a reference for the involvement of transition metal sulfides in advanced oxidation processes (AOPs).

Occurrence and fate of an emerging drug pollutant and its by-products during conventional and advanced wastewater treatment: Case study of furosemide

Conventional wastewater treatment systems are not designed to remove pharmaceutical compounds from wastewater. These compounds can be degraded into many other transformation products which are hardly, if at all, studied. In this context, we studied the occurrence and degradation of furosemide, a very frequently detected diuretic, along with its known degradation products in several types of wastewater. Influent and effluent from the Seine-Centre Wastewater Treatment Plant (WWTP) (Paris, France) as well as outlet of residential care homes (Dordogne, France) were analyzed by Ultra-Performance Liquid Chromatography-tandem Mass Spectrometry (UPLC-MS/MS) to quantify furosemide and its known degradation products, saluamine and pyridinium of furosemide. Oxidation experiments (chlorination, ozonation and UV photolysis with hydrogen peroxide) were then performed on furosemide solutions and on water from residential care facilities to study the degradation of furosemide by potential advanced processes, and also to identify unknown oxidation products by high-resolution mass spectrometry. Furosemide was well degraded in Seine-Centre WWTP (>75%) but did not increase the concentrations of its main degradation products. Saluamine and pyridinium of furosemide were already present at similar concentrations to furosemide in the raw wastewater (∼2.5-3.5 μg.L^-1), and their removal in the WWTPs were very high (>80%). Despite their removal, the three compounds remained present in treated wastewater effluents at concentrations of hundreds of nanograms per liter. Chlorination degraded furosemide without pyridinium production unlike the other two processes. Chlorination and ozonation were also effective for the removal of furosemide and pyridinium in residential care home water, but they resulted in the production of saluamine. To our knowledge this is the first evidence of saluamine and pyridinium of furosemide in real water samples in either the particulate or dissolved phase.

Occurrence of herbicides in the aquatic environment and their removal using advanced oxidation processes: a critical review

Herbicides are chemicals used globally to kill unwanted plants so as to obtain high agricultural yields and good agricultural products. Herbicides are sometimes transported from the farmlands into water bodies mainly through runoffs. These chemicals are recalcitrant, and their accumulation is hazardous to abiotic and biotic components of the ecosystem. At present, the best alternative technology for elimination of herbicides in water is the usage of advanced oxidation processes (AOPs). The AOPs, which are performed homogeneously or heterogeneously, are capable of breaking down complex pollutants in water into carbon dioxide and mineral compounds. In these processes, ^·OH is produced and used for degradation process. It is recommended that the total organic carbon (TOC) produced during degradation reaction be monitored because the ‧OH produced or generated can react to form intermediates before complete mineralisation is achieved. Different kinds of AOPs for degradation of herbicides have their specific advantages as well as limitations. This report shows that AOPs are excellent techniques for degradation of herbicides in aqueous solutions, and the mechanisms showed that herbicides were mineralised. The amount and type of photocatalysts, pH of the medium, surface characteristics of the photocatalysts, doping of the photocatalysts, temperature of the medium, concentration of herbicides, presence of competing ions, intensity and irradiation period, and type of oxidants have great influence on the degradation of herbicides in water. Overall, this report showed that most AOPs could not completely degrade herbicides in water and complete degradation can be achieved by developing novel and robust AOPs that will completely mineralise herbicides in water-this will pave way for water and environmental safety.

Recent advances in the removal of emerging contaminants from water by novel molecularly imprinted materials in advanced oxidation processes-A review

Recently, there has been a global focus on effectively treating emerging contaminants (ECs) in water bodies. Advanced oxidation processes (AOPs) are the primary technology used for ECs removal. However, the low concentrations of ECs make it difficult to overcome the interference of background substances in complex water quality, which limits the practical application of AOPs. To address this limitation, many researchers are developing new catalysts with preferential adsorption. Molecular imprinting technology (MIT) combined with conventional catalysts has been found to effectively enhance the selectivity of catalysts for the targeted catalytic degradation of pollutants. This review presents a comprehensive summary of the progress made in research on molecularly imprinted polymers (MIPs) in the selective oxidation of ECs in water. The preparation methods, principles, and control points of novel MIP catalysts are discussed. Furthermore, the performance and mechanism of the catalysts in photocatalytic oxidation, electrocatalytic oxidation, and persulfate activation are analyzed with examples. The possible ecotoxicological risks of MIP catalysts are also discussed. Finally, the challenges and prospects of applying MIP catalysts in AOP are presented along with proposed solutions. This review provides a better understanding of using MIP catalysts in AOPs to target the degradation of ECs.

Catalytic degradation of dimethomorph by nitrogen-doped rice husk biochar

N-doped biochar is widely used for activating persulfate to degrade organic pollutants. Which type of N atom is the key factor for activation is still unclear and needs to be further explored and analyzed. In this study, four kinds of biochar were prepared using urea and rice husk as precursors, and tested for the catalytic degradation of dimethomorph. Increasing the nitrogen doping level caused the catalytic removal efficiency of dimethomorph in the presence of peroxymonosulfate increased from 16.6% to 86.8%. A correlation analysis showed that the ability of N-doped biochar to activate PMS is mainly related to the content of pyrrole N, graphite N and carbonyl and the degree of defects. In experiments on electron paramagnetic resonance and free radical suppression, the reactive species of SO₄^•-, ¹O₂,·OH and O₂^.- were detected, among which ¹O₂ was found to be the main agent in the nonradical pathway. The degradation pathways for dimethomorph were analyzed based on a total of 8 degradation products identified by high-performance liquid chromatography-time of flight mass spectrometry (HPLC-Q-TOFMS). The results of this study provide a fundamental basis for using agricultural waste to produce inexpensive and efficient nonmetal catalysts that are highly effective in reducing dimethomorph levels in agricultural lands.

Oxidation of the nitrogen-free phosphonate antiscalants HEDP and PBTC in reverse osmosis concentrates: Reaction kinetics and degradation rate

Reverse osmosis (RO) is an advanced technology used to produce potable water from a variety of water sources, including surface water, seawater and wastewater. The yield of the product water from the RO systems is increased by the addition of antiscalants which prevent scaling from calcium and other ions. Removal of antiscalants from RO concentrate can induce the precipitation of oversaturated scale-forming substances, enable additional water recovery from RO concentrates, and reduce the risk of eutrophication after concentrate disposal into the receiving water (e.g., river water). This study aims to provide a better insight into oxidation reactions of the N-free phosphonate antiscalants 1-hydroxyethane-1,1-diphosphonic acid (HEDP) and 2-phosphonobutane-1,2,4-tricarboxylic acid (PBTC) with ozone, hydroxyl radical (^•OH) and sulfate radicals (SO₄^•-). Ozone barely reacts with HEDP and PBTC at pH 7 (k < 10 M^-1s ^- 1), while second order reaction rates of SO₄^•- and ^•OH were determined to be in the range 10⁷-10⁸M ^- 1s ^- 1. Sulfate, silicate and chloride matrices increased HEDP ozone degradation rate possibly due to metal complexation effect. Whereas carbonate and chloride hindered PBTC ozone degradation, and natural organic matter (NOM) inhibited both HEDP and PBTC degradation through scavenging of ^•OH. The SO₄^•-- radical based oxidation process of HEDP and PBTC is mainly inhibited by carbonate and NOM, interestingly only HEDP degradation is inhibited by chloride whereby the PBTC could not be fully degraded (degradation < 60%). The oxidation of PBTC is in real RO concentrates in both processes limited to 10% degradation, whereas HEDP could be degraded up to 60% with ozone and UV/persulfate application.

Peracetic acid activation via the synergic effect of Co and Fe in CoFe-LDH for efficient degradation of pharmaceuticals in hospital wastewater

As an oxidant, peracetic acid (PAA) is gradually applied in advanced oxidation processes (AOPs) for pollutants degradation due to its high oxidation and low toxicity. In this study, the prepared Co₂Fe₁-LDH showed excellent PAA activation ability for efficient degradation of various pharmaceuticals with a removal efficiency ranging from 82.3% to 100%. Taking sulfamethoxazole (SMX) as a model pharmaceutical, it's found that organic radical (R-O^•) with high concentration of 5.27 × 10^-13 M is the dominant ROS responsible for contaminants degradation. Further analysis demonstrated that bimetallic synergistic effect between Co and Fe can improve electron transfer ability of Co₂Fe₁-LDH, resulting in the accelerated conversion of Co from +3 to +2 valence state with a high reaction rate (4.3 × 10¹-1.483 × 10² M^-1 s^-1) in this system. Density functional theory (DFT) reveals that C1, C3, C5 and N11 with higher ƒ⁰ and ƒ^-values concentrated on aniline group of SMX are the main attack sites, which is consistent with the results of degradation products. Besides, Co₂Fe₁-LDH/PAA system can effectively reduce biological toxicity after reaction, due to lower biotoxicity of degradation products and the carbon sources provided by PAA. In application, Co₂Fe₁-LDH/PAA system was capable of resisting the influence of water matrix and effectively removing pollutants in actual hospital wastewater. Importantly, this study comprehensively evaluated the ability of Co₂Fe₁-LDH/PAA system to remove organics and improve the biodegradability of actual hospital wastewater, providing guidance for application of PAA activation system.

Inactivation of the waterborne marine pathogen Vibrio alginolyticus by photo-chemical processes driven by UV-A, UV-B, or UV-C LED combined with H2O2 or HSO5. WATER RESEARCH 2023;232:119686. [PMID: 36764105 DOI: 10.1016/j.watres.2023.119686]

Ultraviolet (UV) radiation is a well-implemented process for water disinfection. The development of emergent UV sources, such as light-emitting diodes (LEDs), has afforded new possibilities for advanced oxidation processes. The emission wavelength is considered to be an important factor for photo-chemical processes in terms of both biological damage and energetic efficiency, as the inactivation mechanisms and mode-of-action may differ according to the wavelength that is applied. In addition, these processes merit exploration for inactivating emerging pathogens, such as marine vibrios, that are important bacteria to control in maritime activities. The main goal of this study was to compare the disinfection efficacy of several UV-LED driven processes with different modes of action. First, the effect of UV-LEDs was assessed at different UV ranges (UV-A, UV-B, or UV-C). Second, the possible enhancement of a combination with hydrogen peroxide (H₂O₂) or peroxymonosulfate salt (HSO₅^-) was investigated under two different application strategies, i.e. simultaneous or sequential. The results obtained indicate a high sensitivity of Vibrio alginolyticus to UV radiation, especially under UV-B (k_obs = 0.24 cm²/mJ) and UV-C (k_obs = 1.47 cm²/mJ) irradiation. The highest inactivation rate constants were obtained for UV/HSO₅^- (k_obs (cm²/mJ)=0.0007 (UV-A); 0.39 (UV-B); 1.79 (UV-C)) with respect to UV/H₂O₂ (k_obs (cm²/mJ)=0.0006 (UV-A); 0.26 (UV-B); and 1.54 (UV-C)) processes, however, regrowth was avoided only with UV/H₂O₂. Additionally, the disinfection enhancement caused by a chemical addition was more evident in the order UV-A > UV-B > UV-C. By applying H₂O₂ (10 mg/L) or HSO₅^- (2.5 mg/L) in a sequential mode before the UV, negligible effects were obtained in comparison with the simultaneous application. Finally, promising electrical energy per order (EE_O) values were obtained as follows: UV/HSO₅^- (EE_O (kWh/m³)=1.68 (UV-A); 0.20 (UV-B); 0.04 (UV-C)) and UV/H₂O₂ (EE_O (kWh/m³)=2.15 (UV-A); 0.32 (UV-B); 0.04 (UV-C)), demonstrating the potential of UV-LEDs for disinfection in particular activities such as the aquaculture industry or maritime transport.

Advances of non-thermal plasma discharge technology in degrading recalcitrant wastewater pollutants. A comprehensive review

With development and urbanization, the amount of wastewater generated due to human activities drastically increases yearly, causing water pollution and intensifying the already worsened water crisis. Although convenient, conventional wastewater treatment methods such as activated sludge, stabilization ponds, and adsorption techniques cannot fully eradicate the complex and recalcitrant contaminants leading to toxic byproducts generation. Recent advancements in wastewater treatment techniques, specifically non-thermal plasma technology, have been extensively investigated for the degradation of complex pollutants in wastewater. Non-thermal plasma is an effective alternative for degrading and augmenting the biodegradability of recalcitrant pollutants due to its ability to generate reactive species in situ. This article critically reviews the non-thermal plasma technology, considering the plasma discharge configuration and reactor types. Furthermore, the influence of operational parameters on the efficiency of the plasma systems and the reactive species generated by the system during discharge has gained significant interest and hence been discussed. Also, the application of non-thermal plasma technology for the degradation of pharmaceuticals, pesticides, and dyes and the inactivation of microbial activities are outlined in this review article. Additionally, optimistic applications involving the combination of non-thermal plasma and catalysts and pilot and industrial-scale projects utilizing non-thermal plasma technology have been addressed. Concluding perceptions on the challenges and future perspectives of the non-thermal technology on wastewater treatment are accentuated. Overall, this review outlines a comprehensive understanding of the non-thermal plasma technology for recalcitrant pollutant degradation from a scientific perspective providing detailed instances for reference.

A review of advanced oxidation process towards organic pollutants and its potential application in fracturing flowback fluid

Fracturing flowback fluid (FFF) including various kinds of organic pollutants that do harms to people and new treatments are urgently needed. Advanced oxidation processes (AOPs) are suitable methods in consideration with molecular weight, removal cost and efficiency. Here, we summarize the recent studies about AOP treatments towards organic pollutants and discuss the application prospects in treatment of FFF. Immobilization and loading methods of catalysts, evaluation method of degradation of FFF, and continuous treatment process flow are discussed in this review. In conclusion, further studies are urgently needed in aspects of catalyst loading methods, macromolecule organic evaluation methods, industrial process, and pathways of macromolecule organics' decomposition.

Degradation of Phenol via an Advanced Oxidation Process (AOP) with Immobilized Commercial Titanium Dioxide (TiO2) Photocatalysts

Four commercial titanium dioxide (TiO₂) photocatalysts, namely P25, P90, PC105, and PC500, were immobilized onto steel plates using a sol-gel binder and investigated for phenol degradation under 365 nm UV-LED irradiation. High-performance liquid chromatography (HPLC) and total organic carbon (TOC) analyses were performed to study the impact of three types of oxygen sources (air, dispersed synthetic air, and hydrogen peroxide) on the photocatalytic performance. The photocatalyst films were stable and there were significant differences in their performance. The best result was obtained with the P90/UV/H₂O₂ system with 100% degradation and about 70% mineralization within 3 h of irradiation. The operating conditions varied, showing that water quality is crucial for the performance. A wastewater treatment plant was developed based on the lab-scale results and water treatment costs were estimated for two cases of irradiation: UV-LED (about 600 EUR/m³) and sunlight (about 60 EUR/m³). The data show the high potential of immobilized photocatalysts for pollutant degradation under advanced oxidation process (AOP) conditions, but there is still a need for optimization to further reduce treatment costs.

A novel aminated lignin/geopolymer supported with Fe nanoparticles for removing Cr(VI) and naphthalene: Intermediates promoting the reduction of Cr(VI)

A novel, inexpensive and eco-friendly aminated lignin/geopolymer supported with Fe nanoparticles (Fe@N-L-GM) composite was successfully synthesized using kaolin and lignin as the major precursors. The prepared Fe@N-L-GM had larger specific surface area, rich oxygen-containing and nitrogen-containing functional groups, greater electron transfer ability and interconnective porous structure. The Fe@N-L-GM could be employed as the adsorbent of Cr(VI) and the activator of potassium peroxymonosulfate (PMS) for treatment of Cr(VI) and naphthalene (NAP) in wastewater. The adsorption and degradation results indicated that the maximum adsorption capacity of Cr(VI) could reach 65.83 mg g^-1, whereas the maximum NAP degradation efficiency could reach 97.81 %. The adsorbed Cr(VI) was mostly converted to the low toxic Cr(III) through the reduction of electron donors such as Fe(II), amino and hydroxyl groups. The quenching experiment results confirmed that ·OH might be the crucial ROSs in mediating NAP degradation. In the simultaneous removal experiment of Cr(VI) and NAP, the Cr(VI) removal rate was significantly improved in the presence of NAP, while phenol as the degradation intermediate of NAP might be the main substance for promoting the reduction of Cr(VI). This work provided the theoretical foundation and a new type of material for the simultaneous removal of heavy metal and persistent organic pollutants (POPs).

Integrated genotoxicity of secondary and tertiary treatment effluents in North China

Genotoxic effects on aquatic organisms caused by wastewater discharging have raised extensive concerns. However, the efficiency of various wastewater treatment processes to reduce effluent genotoxicity was not well known. Genotoxic effects of effluents from four secondary wastewater treatment plants (SWTPs) and a tertiary wastewater treatment plant (TTP) in north China on Chinese rare minnows (Gobiocypris rarus) were evaluated and the toxicity reduction efficiency of various treatment techniques was compared. SWTPs and TTP final effluents disturbed the antioxidant system and lipid peroxidation, with malondialdehyde (MDA) contents in the fish livers and gills increasing to 1.4-2.4 folds and 1.6-3.1 folds of control, respectively. Significant increases in erythrocytes micronucleus (MN) frequency were induced by effluent, and liver DNA damage caused by final SWTPs effluent was 29-54 % lower than TTP effluent. Further, DNA repair gene atm and growth arrest gene gadd45a were remarkably upregulated by SWTP and TTP final effluents to 1.8-12 folds and 4.1-15 folds, respectively, being consistent with the chromosomal aberration and DNA damage in liver tissue. Integrated biomarker response (IBR) of the tertiary effluent was 49 %-69 % lower than the secondary effluents. However, the final ozone disinfection at TTP caused an increase in the DNA damage, suggesting the generation of genotoxic by-products. UV disinfection at secondary treatment removed part of genotoxicity, with a reduction in IBR of 0 %-47 %. The total semi-volatile organic compounds (SVOCs) detected in the final effluent contained 5 %-56 % potential genotoxic substances, removal of which was 9 %-51 % lower than non-genotoxic compounds. Microfiltration and reverse osmosis process exhibited good performance in removing both the integrated genotoxicity and the potential genotoxic SVOCs. Our finding shows that TTP is superior than SWTP for wastewater treatment due to higher genotoxicity removal, but ozone disinfection needs improvement by optimizing performance parameters or adding post-treatment processes, to achieve better protection for aquatic organisms against genotoxic contaminants.

Roles of radical species in vacuum-UV/UV/peroxydisulfate advanced oxidation processes and contributions of the species to contaminant degradation at different water depths

Vacuum-UV (VUV) (wavelength 185 nm)/ UV (wavelength 254 nm) are applied to improve performances of UV-based advanced oxidation processes. However, the improvements were strongly affected by water depth because of poor VUV transmittance in water. In this study, VUV/UV and peroxydisulfate (PDS) were used to degrade carbamazepine. More SO₄^•- oxidation occurred in VUV/UV/PDS than VUV/UV with similar ^•OH oxidation occurring. The additional SO₄^•- oxidation could be caused by VUV/PDS in superficial water or UV/PDS in deeper water. The synergistic factor for VUV/UV/PDS processes relative to VUV/UV and UV/PDS processes was 1.32. VUV/UV/PDS performances were affected by competition for photon absorption by dissolved organic matter (32-58 % inhibition), radical quenching by CO₃^2-/HCO₃^- and NO₃^-, and conversion of ^•OH and SO₄^•- into reactive chlorine species by Cl^-. Radical probe experiments and steady-state kinetic modeling simulations indicated that 34 %, 25 %, and 40 % of carbamazepine degradation occurring in 2-cm-deep bulk solution was due to ^•OH oxidation through VUV/H₂O, SO₄^•- oxidation through VUV/PDS, and SO₄^•- oxidation through UV/PDS, respectively. Contribution of VUV-driven processes decreased with increasing water depth and became equivalent to contribution of 3.5-cm-deep UV-driven processes, which indicated the importance of optimizing water depth in VUV/UV-advanced oxidation process reactors.

Unraveling the critical role of iron-enriched sludge hydrochar in mediating the Fenton-like oxidation of triclosan

The traditional Fenton system is subject to the low efficiency of the Fe(III)/Fe(II) conversion cycle, with significant attempts made to improve the oxidation efficiency by overcoming this hurdle. In support of this goal, iron-enriched sludge-derived hydrochar was prepared as a high-efficiency catalyst by one-step hydrothermal carbonization and its performance and mechanisms in mediating the oxidation of triclosan were explored in the present study. The hydrochar prepared at 240 °C for 4 h (HC_240-4) had the highest removal of triclosan (97.0%). The removal of triclosan in the HC_240-4/H₂O₂ system was greater than 90% in both acidic and near-neutral environments and remained as high as 83.5% after three cycles, indicating the broad pH applicability and great recycling stability of sludge-derived hydrochar in Fenton-like systems. H₂O₂ was activated by both persistent free radicals (PFRs; 19.7%) and iron (80.3%). The binding of Fe(III) to carboxyl decreased the electron transfer energy from H₂O₂ to Fe(III), making its degradation efficiency 2.6 times greater than that of the conventional Fenton reaction. The study provides a way for iron-enriched sludge utilization and reveals a role for hydrochar in promoting iron cycling and electron transfer in the Fenton reaction.

Activation Mechanism of a Peroxymonosulfate-based Fenton-like System with Birnessite and Cu2+ Modified Birnessite

The peroxymonosulfate (PMS) activation mechanism is closely related to the structure/configuration of the "active site" of the Fenton-like catalysts. In this paper, it is shown that Cu²⁺ chemically bonds the surface of birnessite at the Mn vacancy site to form triple-corner-sharing inner-sphere surface complexes (Cu-Bir), which regulates the PMS activation mechanism. Birnessite/PMS Fenton-like system degrades phenol via a non-radical mechanism, which involves high valent Mn(V)=O generated from the surface reaction of Mn(III) with adsorbed PMS. While Cu-Bir initiates an additional radical mechanism that involves reactive oxygen species of ⋅O₂ ^- and ¹ O₂ , and the k value of 5Cu-Bir is 1.9 times higher than that of Bir. The Fenton-like reaction mechanism of the Cu-Bir/PMS system is thus proposed as a radical and non-radical cooccurrence mechanism, which involves a synergistic effect that the radical pathway accelerates the regeneration of Mn(III) for the non-radical pathway, and the non-radical pathway assists to produce ¹ O₂ for the radical pathway.

Reduced Graphene Oxide/Waste-Derived TiO2 Composite Membranes: Preliminary Study of a New Material for Hybrid Wastewater Treatment

This work reports the preliminary results of the development of composite self-assembling membranes obtained by the combination of reduced graphene oxide (rGO) with commercial Degussa P25 titanium dioxide (TiO₂). The purpose is to demonstrate the possibility of combining, in the same self-standing material, the capability to treat wastewater containing both inorganic and organic pollutants by exploiting the established ability of rGO to capture metal ions together with that of TiO₂ to degrade organic substances. Moreover, this study also investigates the potential photocatalytic properties of tionite (TIO), to demonstrate the feasibility of replacing commercial TiO₂ with such waste-derived TiO₂-containing material, fulfilling a circular economy approach. Thus, rGO-TiO₂ and rGO-TIO composite membranes, 1:1 by weight, were prepared and characterized by SEM-EDX, XRD, thermogravimetry, as well as by Raman and UV-Vis spectroscopies to verify the effective and homogeneous integration of the two components. Then, they were tested towards 3-mg L^-1 aqueous synthetic solutions of Fe³⁺ and Cu²⁺ ions to evaluate their metal adsorption ability, with values of the order of 0.1-0.2 mmol g_membrane^-1, comparable or even slightly higher than those of pristine rGO. Finally, the ability of the composites to degrade a common organic pesticide, i.e., Imidacloprid^®, was assessed in preliminary photocatalysis experiments, in which maximum degradation efficiencies of 25% (after 3 h) for rGO-TiO₂ and of 21% (after 1 h) for rGO-TIO were found. The result of tionite-containing membranes is particularly promising and worthy of further investigation, given that the anatase content of tionite is roughly 1/6 of the one in commercial TiO₂.

Embedding Lanthanide Organic Polyhedra into Mesoporous Silica Nanoparticles for the Photocatalytic Degradation of Organic Dyes

Organic pollutants cause severe environmental problems because of their damage to human health and ecological systems. Photocatalytic degradation of persistent organic pollutants is of great importance to address these hazards. Herein, we report a lanthanide organic polyhedra-based hybrid material Gd₈ L₁₂ ⊂MSN with the capability of photocatalytic dye degradation. Gd₈ L₁₂ ⊂MSN was prepared by embedding the Gd₈ L₁₂ complex into mesoporous silica nanoparticles (MSNs) using a "ship-in-a-bottle" strategy. Photocurrent response tests revealed that this hybrid material is a potential semiconductor and could generate a rapid and steady photocurrent upon irradiation. Further dye degradation experiments indicated that it could photocatalyze the degradation of familiar organic dyes. Thereinto, compared with the critical Gd₈ L₁₂ complex, the hybrid material exhibited an acceleration of 2.4 times and realized reusability. This not only offers a potential advanced photocatalyst for degrading persistent organic pollutants, but also provides a strategy for the application of supramolecular materials in environmental science.

Single-Atom Fe-N4 Sites for Catalytic Ozonation to Selectively Induce a Nonradical Pathway toward Wastewater Purification

Nonradical oxidation has been determined to be a promising pathway for the degradation of organic pollutants in heterogeneous catalytic ozonation (HCO). However, the bottlenecks are the rational design of catalysts to selectively induce nonradicals and the interpretation of detailed nonradical generation mechanisms. Herein, we propose a new HCO process based on single-atom iron catalysts, in which Fe-N₄ sites anchored on the carbon skeleton exhibited outstanding catalytic ozonation activity and stability for the degradation of oxalic acid (OA) and p-hydroxybenzoic acid (pHBA) as well as the advanced treatment of a landfill leachate secondary effluent. Unlike traditional radical oxidation, nonradical pathways based on surface-adsorbed atomic oxygen (*O_ad) and singlet oxygen (¹O₂) were identified. A substrate-dependent behavior was also observed. OA was adsorbed on the catalyst surface and mainly degraded by *O_ad, while pHBA was mostly removed by O₃ and ¹O₂ in the bulk solution. Density functional theory calculations and molecular dynamics simulations revealed that one terminal oxygen atom of ozone preferred bonding with the central iron atom of Fe-N₄, subsequently inducing the cleavage of the O-O bond near the catalyst surface to produce *O_ad and ¹O₂. These findings highlight the structural design of an ozone catalyst and an atomic-level understanding of the nonradical HCO process.

Enhanced antibiotic wastewater degradation by intimately coupled B-Bi3O4Cl photocatalysis and biodegradation reactor: Elucidating degradation principle systematically

Intimately coupled photocatalysis and biodegradation (ICPB) is an emerging technology that has potential applications in the degradation of bio-recalcitrant pollutants. However, the interaction principles between photocatalysts and biofilms in ICPB have not been well developed. This article covers a cooperative degradation scheme coupling photocatalysis and biodegradation for efficient degradation and mineralization of ciprofloxacin (CIP) using ICPB with B-doped Bi₃O₄Cl as the photocatalyst. In consequence, a removal rate of ∼95 % is reached after 40 d. The biofilms inside the ICPB carriers can mineralize the photocatalytic products, thus improving the removal rate of total organic carbon (TOC) by more than 20 %. Interior biofilms are not destroyed by CIP or photocatalysis, and they adapt to ICPB of CIP by enriching in Pseudoxanthomonas, Ferruginibacter, Clostridium, Stenotrophomonas and Comamonas and reconstructing their microbial communities using energy produced by the light-excited photoelectrons. Furthermore, this research gives new opinion into the degradation principles of the ICPB system.

Bismuth-based nanostructured photocatalysts for the remediation of antibiotics and organic dyes

A serious threat to human health and the environment worldwide, in addition to the global energy crisis, is the increasing water pollution caused by micropollutants such as antibiotics and persistent organic dyes. Nanostructured semiconductors in advanced oxidation processes using photocatalysis have recently attracted a lot of interest as a promising green and sustainable wastewater treatment method for a cleaner environment. Due to their narrow bandgaps, distinctive layered structures, plasmonic, piezoelectric and ferroelectric properties, and desirable physicochemical features, bismuth-based nanostructure photocatalysts have emerged as one of the most prominent study topics compared to the commonly used semiconductors (TiO₂ and ZnO). In this review, the most recent developments in the use of photocatalysts based on bismuth (e.g., BiFeO₃, Bi₂MoO₆, BiVO₄, Bi₂WO₆, Bi₂S₃) to remove dyes and antibiotics from wastewater are thoroughly covered. The creation of Z-schemes, Schottky junctions, and heterojunctions, as well as morphological modifications, doping, and other processes are highlighted regarding the fabrication of bismuth-based photocatalysts with improved photocatalytic capabilities. A discussion of general photocatalytic mechanisms is included, along with potential antibiotic and dye degradation pathways in wastewater. Finally, areas that require additional study and attention regarding the usage of photocatalysts based on bismuth for removing pharmaceuticals and textile dyes from wastewater, particularly for real-world applications, are addressed.

Facilely achieved enhancement of Fenton-like reactions by constructing electric microfields

In this work, we found that the presence of non-active ZnO crystals greatly accelerated the degradation of Bisphenol A (BPA) by 3.7 folds in the peroxymonosulfate (PMS, HSO₅^-)/Co₃O₄ system. Our mechanistic study revealed that the ZnO particles would create negative electric microfields around them, which are closely related with the zeta potentials (ζ) of ZnO and affected by solution pH. According to COMSOL simulation, the electrostatic repulsion between ZnO and PMS would drive HSO₅^- toward active Co₃O₄ surface, leading to the concentration increasing of HSO₅^- around active Co₃O₄ particles, which will then improve the degradation performance. The particle size of ZnO will also affect the promoting effect greatly by COMSOL simulation. Therefore, this study for the first time reveals synergy of electric microfields for enhanced heterogeneous Fenton-like reactions, providing a low-cost and effective strategy for enhanced persulfate catalysis.

Combined effect of atmospheric gas plasma and UVA light: A sustainable and green alternative for chemical decontamination and microbial inactivation of fish processing water

The simultaneous use of UVA light irradiation coupled with low energy cold plasma generated by a dielectric barrier discharge prototype, results in significant enhancement of efficiency of the integrated process with respect to the sole plasma treatment. This effect has been demonstrated both on microbial inactivation of a food-borne pathogen, i.e. Listeria monocytogenes, and on the degradation of a compound of biological origin such as phenylalanine. In the latter case, the analysis of its reaction intermediates and the spectroscopic identification and quantification of peroxynitrites, allowed to propose mechanistic hypotheses on the nature of the observed synergistic effects. Moreover, it has been demonstrated that the process does not affect the quality of trout fillets, indicating its suitability as a chlorine-free, green, and sustainable tool for the decontamination of fish processing water.