Bridging the gap between development of point-of-care nucleic acid testing and patient care for sexually transmitted infections

The incidence rates of sexually transmitted infections (STIs), including the four major curable STIs - chlamydia, gonorrhea, trichomoniasis and, syphilis - continue to increase globally, causing medical cost burden and morbidity especially in low and middle-income countries (LMIC). There have seen significant advances in diagnostic testing, but commercial antigen-based point-of-care tests (POCTs) are often insufficiently sensitive and specific, while near-point-of-care (POC) instruments that can perform sensitive and specific nucleic acid amplification tests (NAATs) are technically complex and expensive, especially for LMIC. Thus, there remains a critical need for NAAT-based STI POCTs that can improve diagnosis and curb the ongoing epidemic. Unfortunately, the development of such POCTs has been challenging due to the gap between researchers developing new technologies and healthcare providers using these technologies. This review aims to bridge this gap. We first present a short introduction of the four major STIs, followed by a discussion on the current landscape of commercial near-POC instruments for the detection of these STIs. We present relevant research toward addressing the gaps in developing NAAT-based STI POCT technologies and supplement this discussion with technologies for HIV and other infectious diseases, which may be adapted for STIs. Additionally, as case studies, we highlight the developmental trajectory of two different POCT technologies, including one approved by the United States Food and Drug Administration (FDA). Finally, we offer our perspectives on future development of NAAT-based STI POCT technologies.

Visualized Genotyping from "Sample to Results" Within 25 Minutes by Coupling Recombinase Polymerase Amplification (RPA) With Allele-Specific Invasive Reaction Assisted Gold Nanoparticle Probes Assembling

A simple and rapid genotyping method with less-instrumentation is essential for realizing point-of-care detection of personalized medicine-related gene biomarkers. Herein, we developed a rapid and visualized genotyping method by coupling recombinase polymerase amplification (RPA) with allele-specific invader reaction assisted gold nanoparticle probes assembling. In the method, the DNA targets were firstly amplified by using RPA, which is a rapid isothermal amplification technology. Then an allele-specific invasion reaction was performed to recognize the single nucleotide polymorphisms (SNPs) site in the amplicons, to produce signal molecules that caused discoloration of gold nanoparticle probes. As a result, genotyping was achieved by observing the color change of the reaction by using naked eye without the requirement for any expensive instrument. In order to achieve rapid genotyping detection, the genomic DNA from oral swab lysate samples were used for the RPA templates amplification. In this way, a visualized genotyping from "samples to results" within 25 min was realized. Two clopidogrel related SNPs CYP2C19*2 and CYP2C19*3 of 56 clinical samples were correctly genotyped by using this rapid visualized genotyping assay. In addition, the feasibility for this pathogen genotyping method was also verified by detecting plasmid DNA containing three SARS-COV-2 gene mutation sites, indicating that this method has the potential for clinical sample detection.

Modified uvsY by N-terminal hexahistidine tag addition enhances efficiency of recombinase polymerase amplification to detect SARS-CoV-2 DNA

Background

Methods

Results

Conclusions

Supplementary Information

Fabrication of Wearable PDMS Device for Rapid Detection of Nucleic Acids via Recombinase Polymerase Amplification Operated by Human Body Heat

Pathogen detection by nucleic acid amplification proved its significance during the current coronavirus disease 2019 (COVID-19) pandemic. The emergence of recombinase polymerase amplification (RPA) has enabled nucleic acid amplification in limited-resource conditions owing to the low operating temperatures around the human body. In this study, we fabricated a wearable RPA microdevice using poly(dimethylsiloxane) (PDMS), which can form soft-but tight-contact with human skin without external support during the body-heat-based reaction process. In particular, the curing agent ratio of PDMS was tuned to improve the flexibility and adhesion of the device for better contact with human skin, as well as to temporally bond the microdevice without requiring further surface modification steps. For PDMS characterization, water contact angle measurements and tests for flexibility, stretchability, bond strength, comfortability, and bendability were conducted to confirm the surface properties of the different mixing ratios of PDMS. By using human body heat, the wearable RPA microdevices were successfully applied to amplify 210 bp from Escherichia coli O157:H7 (E. coli O157:H7) and 203 bp from the DNA plasmid SARS-CoV-2 within 23 min. The limit of detection (LOD) was approximately 500 pg/reaction for genomic DNA template (E. coli O157:H7), and 600 fg/reaction for plasmid DNA template (SARS-CoV-2), based on gel electrophoresis. The wearable RPA microdevice could have a high impact on DNA amplification in instrument-free and resource-limited settings.

Recombinase polymerase amplification combined with fast DNA extraction for on–spot identification of Deinagkistrodon acutus, a threatened species

This study addresses the use of recombinase polymerase amplification combined with fast DNA extraction for on–spot identification of Deinagkistrodon acutus, a snake species threatened due to over–exploitation and habitat destruction. For its conservation, an efficient species identification method is urgently neededto fight against illegal capture and trade. Fourteen individuals representing 12 snake species (including D. acutus and other snake species) were collected from mountainous regions in Southern China. Genomic DNA was extracted within five minutes by a modified alkaline lysis method. Species–specific primers for recombinase polymerase amplification (RPA) were designed based on the sequences of cytochrome C oxidase subunit I (COI) barcode region, and an optimized RPA assay system was set up. Specificity and sensitivity of the assay were checked, and the assay was validated by identifying 10 commercial Qi She crude drug samples derived from D. acutus. Under optimized RPA conditions, a distinct single band of 354 bp was amplified only for D. acutus but not for the related snake species. The entire procedure can be completed in 30 min at room temperature. Commercial Qi She crude drug identification validated effectiveness of the established assay system. Using a recombinase polymerase amplification (RPA) assay with rapid DNA extraction, we established an on–spot D. acutus identification method with good specificity and sensitivity. This method could become an efficient tool for rigorous supervision of illegal D. acutus capture and trade.

Sensitive, Single-Pot, Two-Stage Assay for Hepatitis Viruses

When left untreated, hepatitis B virus (HBV) and hepatitis C virus (HCV) infections may cause severe illnesses. Since these infections remain asymptomatic for many years, routine screening of populations at risk is critical for therapy initiation. The current standard of care mandates a screening antibody test for HCV, followed by a confirmatory laboratory-based molecular test and treatment. Multiple visits to the clinic are inconvenient, and many patients fail to follow up. To address this challenge, we have developed sensitive, two-stage, isothermal molecular (Penn-RAMP) point-of-care tests to enable test and treat strategy. Penn-RAMP's first stage is comprised of recombinase polymerase amplification (RPA), while its second stage is comprised of loop-mediated isothermal amplification (LAMP). Penn-RAMP is more sensitive than LAMP or RPA alone. We designed a custom pre-LAMP buffer to maximize the volume of RPA products that can be added to the LAMP reaction mix without inhibition and forward and backward primers. Penn-RAMP was implemented in a single pot comprised of two compartments separated by a thermally removable barrier. RAMP's first stage is carried out above the barrier at the RPA incubation temperature. When the pot is heated to the LAMP incubation temperature, the barrier melts away, and the RPA reaction volume mixes with the pre-LAMP buffer, facilitating second-stage amplification. This entire process can be carried out with minimal instrumentation. Our HBV and HCV tests detect, respectively, as few as 10 and 25 virions within 30 min. The viral load can be estimated based on signal threshold time.

A Review of Isothermal Amplification Methods and Food-Origin Inhibitors against Detecting Food-Borne Pathogens

The isothermal amplification method, a molecular-based diagnostic technology, such as loop-mediated isothermal amplification (LAMP) and recombinase polymerase amplification (RPA), is widely used as an alternative to the time-consuming and labor-intensive culture-based detection method. However, food matrices or other compounds can inhibit molecular-based diagnostic technologies, causing reduced detection efficiencies, and false-negative results. These inhibitors originating from food are polysaccharides and polyphenolic compounds in berries, seafood, and vegetables. Additionally, magnesium ions needed for amplification reactions can also inhibit molecular-based diagnostics. The successful removal of inhibitors originating from food and molecular amplification reaction is therefore proposed to enhance the efficiency of molecular-based diagnostics and allow accurate detection of food-borne pathogens. Among molecular-based diagnostics, PCR inhibitors have been reported. Nevertheless, reports on the mechanism and removal of isothermal amplification method inhibitors are insufficient. Therefore, this review describes inhibitors originating from food and some compounds inhibiting the detection of food-borne pathogens during isothermal amplification.

Magnetic Field-Enhanced Agglutination Readout Combined With Isothermal Reverse Transcription Recombinase Polymerase Amplification for Rapid and Sensitive Molecular Detection of Dengue Virus

Among the numerous molecular diagnostic methods, isothermal reverse transcription recombinase polymerase amplification (RT-RPA) is a simple method that has high sensitivity and avoids the use of expensive instruments. However, detection of amplified genomes often requires a fluorescence readout on costly readers or migration on a lateral flow strip with a subjective visual reading. Aiming to establish a new approach to rapidly and sensitively detect viruses, we combined RT-RPA with a magnetic field-enhanced agglutination (MFEA) assay and assessed the ability of this method to detect the dengue virus (DENV). Magnetization cycles accelerated the capture of amplified DENV genomes between functionalized magnetic nanoparticles by a fast chaining process to less than 5 min; the agglutination was quantified by simple turbidimetry. A total of 37 DENV RNA+ and 30 DENV RNA− samples were evaluated with this combined method. The sensitivity and specificity were 89.19% (95% CI, 72.75–100.00%) and 100% (95% CI, 81.74–100.00%), respectively. This approach provides a solution for developing innovative diagnostic assays for the molecular detection of emerging infections.

Biosensors for the Determination of SARS-CoV-2 Virus and Diagnosis of COVID-19 Infection

Monitoring and tracking infection is required in order to reduce the spread of the coronavirus disease 2019 (COVID-19), induced by severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). To achieve this goal, the development and deployment of quick, accurate, and sensitive diagnostic methods are necessary. The determination of the SARS-CoV-2 virus is performed by biosensing devices, which vary according to detection methods and the biomarkers which are inducing/providing an analytical signal. RNA hybridisation, antigen-antibody affinity interaction, and a variety of other biological reactions are commonly used to generate analytical signals that can be precisely detected using electrochemical, electrochemiluminescence, optical, and other methodologies and transducers. Electrochemical biosensors, in particular, correspond to the current trend of bioanalytical process acceleration and simplification. Immunosensors are based on the determination of antigen-antibody interaction, which on some occasions can be determined in a label-free mode with sufficient sensitivity.

End-User Perspectives on Using Quantitative Real-Time PCR and Genomic Sequencing in the Field

Quantitative real-time PCR and genomic sequencing have become mainstays for performing molecular detection of biological threat agents in the field. There are notional assessments of the benefits, disadvantages, and challenges that each of these technologies offers according to findings in the literature. However, direct comparison between these two technologies in the context of field-forward operations is lacking. Most market surveys, whether published in print form or provided online, are directed to product manufacturers who can address their respective specifications and operations. One method for comparing these technologies is surveying end-users who are best suited for discussing operational capabilities, as they have hands-on experience with state-of-the-art molecular detection platforms and protocols. These end-users include operators in military defense and first response, as well as various research scientists in the public sector such as government and service laboratories, private sector, and civil society such as academia and nonprofit organizations performing method development and executing these protocols in the field. Our objective was to initiate a survey specific to end-users and their feedback. We developed a questionnaire that asked respondents to (1) determine what technologies they currently use, (2) identify the settings where the technologies are used, whether lab-based or field-forward, and (3) rate the technologies according to a set list of criteria. Of particular interest are assessments of sensitivity, specificity, reproducibility, scalability, portability, and discovery power. This article summarizes the findings from the end-user perspective, highlighting technical and operational challenges.

Visible-light and near-infrared fluorescence and surface-enhanced Raman scattering point-of-care sensing and bio-imaging: a review

This review article deals with the concepts, principles and applications of visible-light and near-infrared (NIR) fluorescence and surface-enhanced Raman scattering (SERS) in in vitro point-of-care testing (POCT) and in vivo bio-imaging. It has discussed how to utilize the biological transparency windows to improve the penetration depth and signal-to-noise ratio, and how to use surface plasmon resonance (SPR) to amplify fluorescence and SERS signals. This article has highlighted some plasmonic fluorescence and SERS probes. It has also reviewed the design strategies of fluorescent and SERS sensors in the detection of metal ions, small molecules, proteins and nucleic acids. Particularly, it has provided perspectives on the integration of fluorescent and SERS sensors into microfluidic chips as lab-on-chips to realize point-of-care testing. It has also discussed the design of active microfluidic devices and non-paper- or paper-based lateral flow assays for in vitro diagnostics. In addition, this article has discussed the strategies to design in vivo NIR fluorescence and SERS bio-imaging platforms for monitoring physiological processes and disease progression in live cells and tissues. Moreover, it has highlighted the applications of POCT and bio-imaging in testing toxins, heavy metals, illicit drugs, cancers, traumatic brain injuries, and infectious diseases such as COVID-19, influenza, HIV and sepsis.

Rapid molecular assays for the detection of the four dengue viruses in infected mosquitoes

The pantropic emergence of severe dengue disease can partly be attributed to the co-circulation of different dengue viruses (DENVs) in the same geographical location. Effective monitoring for circulation of each of the four DENVs is critical to inform disease mitigation strategies. In low resource settings, this can be effectively achieved by utilizing inexpensive, rapid, sensitive and specific assays to detect viruses in mosquito populations. In this study, we developed four rapid DENV tests with direct applicability for low-resource virus surveillance in mosquitoes. The test protocols utilize a novel sample preparation step, a single-temperature isothermal amplification, and a simple lateral flow detection. Analytical sensitivity testing demonstrated tests could detect down to 1,000 copies/µL of virus-specific DENV RNA, and analytical specificity testing indicated tests were highly specific for their respective virus, and did not detect closely related flaviviruses. All four DENV tests showed excellent diagnostic specificity and sensitivity when used for detection of both individually infected mosquitoes and infected mosquitoes in pools of uninfected mosquitoes. With individually infected mosquitoes, the rapid DENV-1, -2 and -3 tests showed 100% diagnostic sensitivity (95% CI = 69% to 100%, n=8 for DENV-1; n=10 for DENV 2,3) and the DENV-4 test showed 92% diagnostic sensitivity (CI: 62% to 100%, n=12) along with 100% diagnostic specificity (CI: 48-100%) for all four tests. Testing infected mosquito pools, the rapid DENV-2, -3 and -4 tests showed 100% diagnostic sensitivity (95% CI = 69% to 100%, n=10) and the DENV-1 test showed 90% diagnostic sensitivity (55.50% to 99.75%, n=10) together with 100% diagnostic specificity (CI: 48-100%). Our tests reduce the operational time required to perform mosquito infection status surveillance testing from > two hours to only 35 minutes, and have potential to improve accessibility of mosquito screening, improving monitoring and control strategies in low-income countries most affected by dengue outbreaks.

Evaluation of recombinase-based isothermal amplification assays for point-of-need detection of SARS-CoV-2 in resource-limited settings

OBJECTIVES

The democratization of diagnostics is one of the key challenges towards containing the transmission of coronavirus disease 2019 (COVID-19) around the globe. The operational complexities of existing PCR-based methods, including sample transfer to advanced central laboratories with expensive equipment, limit their use in resource-limited settings. However, with the advent of isothermal technologies, the detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) is possible at decentralized facilities.

METHODS

In this study, two recombinase-based isothermal techniques, reverse transcription recombinase polymerase amplification (RT-RPA) and reverse transcription recombinase-aided amplification (RT-RAA), were evaluated for the detection of SARS-CoV-2 in clinical samples. A total of 76 real-time reverse transcription PCR (real-time RT-PCR) confirmed COVID-19 cases and 100 negative controls were evaluated to determine the diagnostic performance of the isothermal methods.

RESULTS

This investigation revealed equally promising diagnostic accuracy of the two methods, with a sensitivity of 76.32% (95% confidence interval 65.18-85.32%) when the target genes were RdRP and ORF1ab for RT-RPA and RT-RAA, respectively; the combination of N and RdRP in RT-RPA augmented the accuracy of the assay at a sensitivity of 85.53% (95% confidence interval 75.58-92.55%). Furthermore, high specificity was observed for each of the methods, ranging from 94.00% to 98.00% (95% confidence interval 87.40-9.76%).

CONCLUSIONS

Considering the diagnostic accuracies, both RT-RPA and RT-RAA appear to be suitable assays for point-of-need deployment for the detection of the pathogen, understanding its epidemiology, case management, and curbing transmission.

A genosensor for detecting single-point mutations in dendron chips after blocked recombinase polymerase amplification

Dendron–probe conjugates were effectively immobilized on chip surfaces, improving assay sensitivity and simplifying coupling reactions. Combined with an isothermal amplification, the array method accurately detects single-base changes.

Fungal infections diagnosis - Past, present and future

Despite the scientific advances observed in the recent decades and the emergence of new methodologies, the diagnosis of systemic fungal infections persists as a problematic issue. Fungal cultivation, the standard method that allows a proven diagnosis, has numerous disadvantages, as low sensitivity (only 50% of the patients present positive fungal cultures), and long growth time. These are factors that delay the patient's treatment and, consequently, lead to higher hospital costs. To improve the accuracy and quickness of fungal infections diagnosis, several new methodologies attempt to be implemented in clinical microbiology laboratories. Most of these innovative methods are independent of pathogen isolation, which means that the diagnosis goes from being considered proven to probable. In spite of the advantage of being culture-independent, the majority of the methods lack standardization. PCR-based methods are becoming more and more commonly used, which has earned them an important place in hospital laboratories. This can be perceived now, as PCR-based methodologies have proved to be an essential tool fighting against the COVID-19 pandemic. This review aims to go through the main steps of the diagnosis for systemic fungal infection, from diagnostic classifications, through methodologies considered as "gold standard", to the molecular methods currently used, and finally mentioning some of the more futuristic approaches.

CRISPR-based platform for rapid, sensitive and field-deployable detection of scale drop disease virus in Asian sea bass (Lates calcarifer)

Scale drop disease virus (SDDV) is a major pathogen of Asian sea bass that has emerged in many countries across the Asia Pacific since 1992 and carries the potential to cause drastic economic losses to the aquaculture sector. The lack of an approved vaccine for SDDV necessitates timely prevention as the first line of defence against the disease, but current diagnostic platforms still face challenges that render them incompatible with field applications, particularly in resource-limited settings. Here, we developed a novel detection platform for SDDV based on a CRISPR-Cas12a-based nucleic acid detection technology combined with recombinase polymerase amplification (RPA-Cas12a). Using the viral adenosine triphosphatase (SDDV-ATPase) gene as a target, we achieved the detection limit of 40 copies per reaction and high specificity for SDDV. The coupling with fluorescence and lateral flow readouts enables naked-eye visualization and straightforward data interpretation requiring minimal scientific background. Compared with semi-nested PCR in field sample evaluation, our RPA-Cas12a assay is more sensitive and capable of detecting SDDV in asymptomatic fish. Importantly, the entire workflow can be carried out at a constant temperature of 37°C within an hour from start to finish, thus removing the need for an expensive thermal cycling apparatus and long turnaround times associated with PCR-based methods. Therefore, owing to its high accuracy, rapidity and user-friendliness, the developed RPA-Cas12a platform shows the potential for diagnosis of SDDV at point of need and could be a valuable tool to help protect fish farming communities from large-scale epidemics.

Rapid molecular assays for the detection of the four dengue viruses in infected mosquitoes

The pantropic emergence of severe dengue disease can partly be attributed to the co-circulation of different dengue viruses (DENVs) in the same geographical location. Effective monitoring for circulation of each of the four DENVs is critical to inform disease mitigation strategies. In low resource settings, this can be effectively achieved by utilizing inexpensive, rapid, sensitive and specific assays to detect viruses in mosquito populations. In this study, we developed four rapid DENV tests with direct applicability for low-resource virus surveillance in mosquitoes. The test protocols utilize a novel sample preparation step, a single-temperature isothermal amplification, and a simple lateral flow detection. Analytical sensitivity testing demonstrated tests could detect down to 1,000 copies/µL of virus-specific DENV RNA, and analytical specificity testing indicated tests were highly specific for their respective virus, and did not detect closely related flaviviruses. All four DENV tests showed excellent diagnostic specificity and sensitivity when used for detection of both individually infected mosquitoes and infected mosquitoes in pools of uninfected mosquitoes. With individually infected mosquitoes, the rapid DENV-1, -2 and -3 tests showed 100% diagnostic sensitivity (95% CI = 69% to 100%, n=8 for DENV-1; n=10 for DENV 2,3) and the DENV-4 test showed 92% diagnostic sensitivity (CI: 62% to 100%, n=12) along with 100% diagnostic specificity (CI: 48-100%) for all four tests. Testing infected mosquito pools, the rapid DENV-2, -3 and -4 tests showed 100% diagnostic sensitivity (95% CI = 69% to 100%, n=10) and the DENV-1 test showed 90% diagnostic sensitivity (55.50% to 99.75%, n=10) together with 100% diagnostic specificity (CI: 48-100%). Our tests reduce the operational time required to perform mosquito infection status surveillance testing from > two hours to only 35 minutes, and have potential to improve accessibility of mosquito screening, improving monitoring and control strategies in low-income countries most affected by dengue outbreaks.

A Rapid Drug Resistance Genotyping Workflow for Mycobacterium tuberculosis, Using Targeted Isothermal Amplification and Nanopore Sequencing

Phenotypic drug susceptibility testing (DST) for tuberculosis (TB) requires weeks to yield results. Although molecular tests rapidly detect drug resistance-associated mutations (DRMs), they are not scalable to cover the full genome and the many DRMs that can predict resistance. Whole-genome sequencing (WGS) methods are scalable, but if conducted directly on sputum, typically require a target enrichment step, such as nucleic acid amplification. We developed a targeted isothermal amplification-nanopore sequencing workflow for rapid prediction of drug resistance of TB isolates. We used recombinase polymerase amplification (RPA) to perform targeted isothermal amplification (37°C for 90 min) of three regions within the Mycobacterium tuberculosis genome, followed by nanopore sequencing on the MinION. We tested 29 mycobacterial genomic DNA extracts from patients with drug-resistant (DR) TB and compared our results to those of WGS by Illumina and phenotypic DST to evaluate the accuracy of prediction of resistance to rifampin and isoniazid. Amplification by RPA showed fidelity equivalent to that of high-fidelity PCR (100% concordance). Nanopore sequencing generated DRM predictions identical to those of WGS, with considerably faster sequencing run times of minutes rather than days. The sensitivity and specificity of rifampin resistance prediction for our workflow were 96.3% (95% confidence interval [CI], 81.0 to 99.9%) and 100.0% (95% CI, 15.8 to 100.0%), respectively. For isoniazid resistance prediction, the sensitivity and specificity were 100.0% (95% CI, 86.3 to 100.0%) and 100.0% (95% CI, 39.8 to 100.0%), respectively. The workflow consumable costs per sample are less than £100. Our rapid and low-cost drug resistance genotyping workflow provides accurate prediction of rifampin and isoniazid resistance, making it appropriate for use in resource-limited settings. IMPORTANCE Current methods for diagnosing drug-resistant tuberculosis are time consuming, resulting in delays in patients receiving treatment and in transmission onwards. They also require a high level of laboratory infrastructure, which is often only available at centralized facilities, resulting in further delays to diagnosis and additional barriers to deployment in resource-limited settings. This article describes a new workflow that can diagnose drug-resistant TB in a shorter time, with less equipment, and for a lower price than current methods. The amount of TB DNA is first increased without the need for bulky and costly thermocycling equipment. The DNA is then read using a portable sequencer called a MinION, which indicates whether there are tell-tale changes in the DNA that indicate whether the TB strain is drug resistant. Our workflow could play an important role in the future in the fight against the public health challenge that is TB drug resistance.

A real-time recombinase polymerase amplification assay for fast and accurate detection of Ditylenchus destructor

Ditylenchus destructor is a plant-parasitic nematode that seriously infests sweet potato crop in China. Thus, fast and accurate detection of D. destructor in soil and plant tissue samples is of great significance. In this study, a real-time recombinase polymerase amplification (RPA) assay was developed for the rapid and accurate detection of D. destructor in various samples. The RPA assay could be easily operated and detected as low as 1/500 individual J4 nematode DNA per reaction in 20 min at 39 °C with high specificity. The assay meets the requirements of rapid detection prior to port quarantine as well as on-site real-time detection and can be applied to detect the parasite in soil and plant samples. The modified gDNA extraction method for a single nematode established in this study significantly reduced the time of detection and improved the applicability of the real-time RPA assay for on-site detection in different environments. The real-time RPA assay to detect D. destructor will be useful for epidemiological investigations in the field as well as for quarantine processes in the sweet potato and potato trade.

Rapid visual detection of Aeromonas salmonicida by loop-mediated isothermal amplification with hydroxynaphthol blue dye

To make crucial prevention, reduce fish losses and minimize the economic damage of diseases on the fish farm owners, a rapid detection of fish pathogens is mandatory. In this study, a loop-mediated isothermal amplification assay combined with hydroxynaphthol blue dye (LAMP-HNB) was developed and used for the rapid detection of Aeromonas salmonicida that caused significant economic losses in fish farming. Firstly, a pair of outer and inner primers specific for conserved fragment of vapA gene in A. salmonicida were designed and synthesized. Secondly, by optimizing the reaction conditions including reaction temperature, time, Mg²⁺ concentration, dNTP concentration and primer ratio, a LAMP-HNB assay was successfully established for the detection of A. salmoncida. Thirdly, the assay showed good specificity with no false-positive and false-negative results, and good sensitivity with the detection limit of 3.077 × 10^-6  ng/μl, which was 10² times more sensitive than the conventional PCR. Finally, the LAMP-HNB assay was validated by the fish samples inoculated with different concentrations of A. salmoncida. This is the first development of rapid visual detection of A. salmonicida based on LAMP-HNB assay, which has great application prospect and market for diagnostic testing, health certification and active surveillance programmers.

Rapid detection of Decapod iridescent virus 1 (DIV1) by recombinase polymerase amplification

A recombinase polymerase amplification (RPA) assay was established for the rapid detection of Decapod iridescent virus 1 using primers targeted to the virus's ATPase gene (ORF114R). Optimization experiments showed that the optimal amplification temperature of the RPA assay was 37 °C and that the reaction could be completed within only 15 min. The target band of 15 min. is bright enough. In order to shorten the operational reaction time, consequently, 15 min was the optimal amplification time for our new RPA assay for DIV1. Specificity tests showed that the RPA assay did not exhibit any cross-reactivity with other shrimp pathogens(TSV, MrNV, YHV-1, WSSV, EHP, AHPND, EHNV, RSIV, RGV and IHHNV). Sensitivity tests further showed that the detection limit of the new RPA assay was 200 copies/50 μL, indicating that this assay was more sensitive than a nested polymerase chain reaction (PCR) method. A total of 509 clinical samples were assayed using the RPA and the PCR assays; analysis showed that the RPA method could detect weak-positive samples more effectively than the PCR method. Collectively, these findings indicated that the RPA assay was fast, simple, specific, sensitive and has significant potentials for clinical and on-site testing.

Point of care diagnosis of plant virus: Current trends and prospects

Plant viral diseases accounts for major global economic losses in modern-day agriculture. Plant viral disease management is the primary challenge for both farmers and researchers. Detection and identification of plant viruses are of paramount importance for successful management of a viral disease. Recent advancements in molecular biology have contributed to significant progress in the development of new, sensitive, and effective diagnostic methods. However, most techniques are neither time/cost-effective nor user-friendly and require sophisticated labs. Hence, the past few decades of agricultural research have mainly focused on developing farmer-friendly, point-of-care diagnostic tools that provide high-sensitive rapid diagnosis. The current trend in plant virus diagnostic tools is cheaper, easy-to-use portable devices with no compromise on sensitivity and reproducibility.

The Potential Use of Isothermal Amplification Assays for In-Field Diagnostics of Plant Pathogens

Rapid, sensitive, and timely diagnostics are essential for protecting plants from pathogens. Commonly, PCR techniques are used in laboratories for highly sensitive detection of DNA/RNA from viral, viroid, bacterial, and fungal pathogens of plants. However, using PCR-based methods for in-field diagnostics is a challenge and sometimes nearly impossible. With the advent of isothermal amplification methods, which provide amplification of nucleic acids at a certain temperature and do not require thermocyclic equipment, going beyond the laboratory has become a reality for molecular diagnostics. The amplification stage ceases to be limited by time and instruments. Challenges to solve involve finding suitable approaches for rapid and user-friendly plant preparation and detection of amplicons after amplification. Here, we summarize approaches for in-field diagnostics of phytopathogens based on different types of isothermal amplification and discuss their advantages and disadvantages. In this review, we consider a combination of isothermal amplification methods with extraction and detection methods compatible with in-field phytodiagnostics. Molecular diagnostics in out-of-lab conditions are of particular importance for protecting against viral, bacterial, and fungal phytopathogens in order to quickly prevent and control the spread of disease. We believe that the development of rapid, sensitive, and equipment-free nucleic acid detection methods is the future of phytodiagnostics, and its benefits are already visible.

Solid-Phase Primer Elongation Using Biotinylated dNTPs for the Detection of a Single Nucleotide Polymorphism from a Fingerprick Blood Sample

Isothermal recombinase polymerase amplification-based solid-phase primer extension is used for the optical detection of a hypertrophic cardiomyopathy associated single nucleotide polymorphism (SNP) in a fingerprick blood sample. The assay exploits four thiolated primers which have the same sequences with the exception of the 3'-terminal base. Target DNA containing the SNP site hybridizes to all four of the immobilized probes, with primer extension only taking place from the primer containing the terminal base that is complementary to the SNP under interrogation. Biotinylated deoxynucleotide triphosphates are used in the primer extension, allowing postextension addition of streptavidin-poly-horseradish peroxidase to bind to the incorporated biotinylated dNTPs. The signal generated following substrate addition can then be measured optically. The percentage of biotinylated dNTPs and the duration of primer extension is optimized and the system applied to the identification of a SNP in a fingerprick blood sample. A methodology of thermal lysis using a 1 in 5 dilution of the fingerprick blood sample prior to application of 95 °C for 30 s is used to extract genomic DNA, which is directly used as a template for solid-phase primer extension on microtiter plates, followed by optical detection. The SNP in the fingerprick sample was identified and its identity corroborated using ion torrent next generation sequencing. Ongoing work is focused on extension to the multiplexed detection of SNPs in fingerprick and other biological samples.

Molecular Detection of Infectious Laryngotracheitis Virus in Chickens with a Microfluidic Chip

Simple Summary

Infectious laryngotracheitis (ILT) presents a major risk to the chicken industry. Rapid, specific, simple, and point-of-need molecular detection of the virus is crucial to enable chicken farms to take timely action and contain the spread of infection. The current study describes an isothermal amplification assay for infectious laryngotracheitis virus (ILTV) infection and the implementation of this assay in a microfluidic chip suitable for molecular detection and quasi-quantification of ILTV in diagnostic veterinary laboratories with low resources and poultry farms. Our assay performance was compared and favorably agreed with quantitative PCR (qPCR). Clinical tests of our assay and chip with samples from diseased chickens demonstrated good concordance with the gold-standard benchtop qPCR assay.

Abstract

Infectious laryngotracheitis (ILT) is a viral disease of chickens’ respiratory system that imposes considerable financial burdens on the chicken industry. Rapid, simple, and specific detection of this virus is crucial to enable proper control measures. Polymerase chain reaction (PCR)-based molecular tests require relatively expensive instruments and skilled personnel, confining their application to centralized laboratories. To enable chicken farms to take timely action and contain the spread of infection, we describe a rapid, simple, semi-quantitative benchtop isothermal amplification (LAMP) assay, and a field-deployable microfluidic device for the diagnosis of ILTV infection in chickens. Our assay performance was compared and favorably agreed with quantitative PCR (qPCR). The sensitivity of our real-time LAMP test is 250 genomic copies/reaction. Clinical performance of our microfluidic device using samples from diseased chickens showed 100% specificity and 100% sensitivity in comparison with benchtop LAMP assay and the gold-standard qPCR. Our method facilitates simple, specific, and rapid molecular ILTV detection in low-resource veterinary diagnostic laboratories and can be used for field molecular diagnosis of suspected ILT cases.

Development of a recombinase polymerase amplification assay for rapid detection of Streptococcus suis type 2 in nasopharyngeal swab samples

Streptococcus suis serotype 2 (SS2), an emerging zoonotic pathogen, may induce severe infections and symptoms manifested as septicemia, meningitis and even death both in human and pigs. The aim of this article was to develop a new methodology as real-time recombinase polymerase amplification (RT-RPA) assay targeting cps2J gene for the detection of SS2 (or SS1/2). The sensitivity and reproducibility of RT-RPA results were evaluated and compared with a real-time quantitative PCR (RT-qPCR). The established RT-RPA reaction could be completed in 20 minutes with distinguishable specificity against the predominant S. suis infection serotypes of 3, 4, 5, 7, 9, 14, and 31. Lower detection limit for RT-RPA was 10² genomic DNA copies per reaction. The specimen performance of RT-RPA was tested in nasopharyngeal swab samples with the sensitivity and specificity as 97.5% and 100%, respectively. Thus, this RT-RPA method is a rapid and potential molecular diagnostic tool for SS2 detection.

Recombinase Polymerase Amplification Assay with and without Nuclease-Dependent-Labeled Oligonucleotide Probe

The combination of recombinase polymerase amplification (RPA) and lateral flow test (LFT) is a strong diagnostic tool for rapid pathogen detection in resource-limited conditions. Here, we compared two methods generating labeled RPA amplicons following their detection by LFT: (1) the basic one with primers modified with different tags at the terminals and (2) the nuclease-dependent one with the primers and labeled oligonucleotide probe for nuclease digestion that was recommended for the high specificity of the assay. Using both methods, we developed an RPA-LFT assay for the detection of worldwide distributed phytopathogen-alfalfa mosaic virus (AMV). A forward primer modified with fluorescein and a reverse primer with biotin and fluorescein-labeled oligonucleotide probe were designed and verified by RPA. Both labeling approaches and their related assays were characterized using the in vitro-transcribed mRNA of AMV and reverse transcription reaction. The results demonstrated that the RPA-LFT assay based on primers-labeling detected 103 copies of RNA in reaction during 30 min and had a half-maximal binding concentration 22 times lower than probe-dependent RPA-LFT. The developed RPA-LFT was successfully applied for the detection of AMV-infected plants. The results can be the main reason for choosing simple labeling with primers for RPA-LFT for the detection of other pathogens.

The CRISPR-Cas toolbox for analytical and diagnostic assay development

Clustered Regularly Interspaced Short Palindromic Repeats (CRISPR) and CRISPR-associated (Cas) systems have revolutionized biological and biomedical sciences in many ways. The last few years have also seen tremendous interest in deploying the CRISPR-Cas toolbox for analytical and diagnostic assay development because CRISPR-Cas is one of the most powerful classes of molecular machineries for the recognition and manipulation of nucleic acids. In the short period of development, many CRISPR-enabled assays have already established critical roles in clinical diagnostics, biosensing, and bioimaging. We describe in this review the recent advances and design principles of CRISPR mediated analytical tools with an emphasis on the functional roles of CRISPR-Cas machineries as highly efficient binders and molecular scissors. We highlight the diverse engineering approaches for molecularly modifying CRISPR-Cas machineries and for devising better readout platforms. We discuss the potential roles of these new approaches and platforms in enhancing assay sensitivity, specificity, multiplexity, and clinical outcomes. By illustrating the biochemical and analytical processes, we hope this review will help guide the best use of the CRISPR-Cas toolbox in detecting, quantifying and imaging biologically and clinically important molecules and inspire new ideas, technological advances and engineering strategies for addressing real-world challenges such as the on-going COVID-19 pandemic.

Electroanalytical Paper-Based Nucleic Acid Amplification Biosensors with Integrated Thread Electrodes

Nucleic acid amplification tests (NAATs) are very sensitive and specific methods, but they mainly rely on centralized laboratories and therefore are not suitable for point-of-care testing. Here, we present a 3D microfluidic paper-based electrochemical NAAT. These devices use off-the-shelf gold plasma-coated threads to integrate electroanalytical readouts using ex situ self-assembled monolayer formation on the threads prior to assembling into the paper device. They further include a sandwich hybridization assay with sample incubation, rinsing, and detection steps all integrated using movable stacks of filter papers to allow time-sequenced reactions. The devices use glass fiber substrates for storing recombinase polymerase amplification reagents and conducting the isothermal amplification. We used the paper-based device for the detection of the toxic microalgae Ostreopsis cf. ovata. The NAAT, completed in 95 min, attained a limit of detection of 0.06 pM target synthetic DNA and was able to detect 1 ng/μL O. cf. ovata genomic DNA with negligible cross-reactivity from a closely related microalgae species. We think that the integration of thread electrodes within paper-based devices paves the way for digital one-time use NAATs and numerous other advanced electroanalytical paper- or textile-based devices.

Development of Quantitative Rapid Isothermal Amplification Assay for Leishmania donovani

Quantification of pathogen load, although challenging, is of paramount importance for accurate diagnosis and clinical management of a range of infectious diseases in a point-of-need testing (PONT) scenario such as in resource-limited settings. We formulated a quantification approach to test the standard-curve based absolute quantification ability of isothermal recombinase polymerase amplification (RPA) assay. As a test of principle, a 10-fold dilution series of Leishmania donovani (LD) genomic DNA prepared in nuclease-free-water (NFW), and from culture-spiked-blood (CSB) were tested, and a 15 min assay was performed. A modified algorithm was formulated to derive the detection outcome. The threshold-record times (Tr) in seconds thus obtained were plotted against the initial load of parasite genomes for log-linear regression analysis. The quantitative RPA (Q-RPA) assay was further evaluated against a LD quantitative (q)-PCR assay with DNA extracted from visceral and post-Kala-azar dermal leishmaniasis case specimens and stratified into different ranges of threshold cycle (Ct). The best-fitted regression models were found linear with mean r²/root mean square error (RMSE) values of residual points (in seconds) estimated as 0.996/8.063 and 0.992/7.46 for replicated series of NFW and CSB, respectively. In both series, the lower limit of detection reached less than 0.1 parasite genome equivalent DNA. Absolute agreement between Q-RPA and LD-qPCR was found for test positivity, and strong positive correlations were observed between the Tr and Ct values (r = 0.89; p < 0.0001) as well as between the absolute parasite loads (r = 0.87; p < 0.0001) quantified by respective assays. The findings in this very first Q-RPA assay for leishmaniasis are suggestive of its potential in monitoring LD load in clinical specimens, and the development of rapid Q-RPA assays for other infectious diseases.

Multiplex Assay of Viruses Integrating Recombinase Polymerase Amplification, Barcode-Anti-Barcode Pairs, Blocking Anti-Primers, and Lateral Flow Assay

A multiplex assay based on recombinase polymerase amplification (RPA) and lateral flow test (LFT) is a desirable tool for many areas. This multiplex assay could be efficiently realized using single-stranded (ss) DNAs located in separate zones on the test strip and bound complementary ssDNA tags of double-stranded (ds) DNA amplicons. Here, we investigate how to enrich multiplex assay capabilities using ssDNAs. Bifunctional oligonucleotide probes integrating (1) a forward primer for RPA, (2) a C9 spacer to stop polymerase, and (3) a ssDNA tag for binding at test strip are developed. The amplicons have a unique individual ssDNA tag at one end and a universal label of fluorescein introducing through a reverse primer at the other end. A conjugate of gold nanoparticles (GNP) with antibodies to fluorescein is used to detect all amplicons. The remainder of primers after RPA interacting with GNP conjugate was found to be a limiting factor for sensitive and specific multiplex assay. The addition of anti-RPA-primers before the use of test strips was proposed to simply and effectively eliminate remaining primers. This approach was successfully applied for the detection of three priority plant RNA viruses: potato virus Y (PVY), -S (PVS) and potato leafroll virus (PLRV). The total time of the assay is 30 min. The multiplex RPA-LFT detected at least 4 ng of PVY per g of plant leaves, 0.04 ng/g for PVS, and 0.04 ng/g for PLRV. The testing of healthy and infected potato samples showed concordance between the developed assay and reverse transcription-polymerase chain reaction. Thus, the capabilities of the proposed universal modules (ssDNA anchors, bifunctional probes, and blocking anti-primers) for multiplex detection of RNA analytes with high specificity and sensitivity were demonstrated.

Using Cy5-dUTP labelling of RPA-amplicons with downstream microarray analysis for the detection of antibiotic resistance genes

In this report we describe Cy5-dUTP labelling of recombinase-polymerase-amplification (RPA) products directly during the amplification process for the first time. Nucleic acid amplification techniques, especially polymerase-chain-reaction as well as various isothermal amplification methods such as RPA, becomes a promising tool in the detection of pathogens and target specific genes. Actually, RPA even provides more advantages. This isothermal method got popular in point of care diagnostics because of its speed and sensitivity but requires pre-labelled primer or probes for a following detection of the amplicons. To overcome this disadvantages, we performed an labelling of RPA-amplicons with Cy5-dUTP without the need of pre-labelled primers. The amplification results of various multiple antibiotic resistance genes indicating great potential as a flexible and promising tool with high specific and sensitive detection capabilities of the target genes. After the determination of an appropriate rate of 1% Cy5-dUTP and 99% unlabelled dTTP we were able to detect the bla_CTX-M15 gene in less than 1.6E-03 ng genomic DNA corresponding to approximately 200 cfu of Escherichia coli cells in only 40 min amplification time.

Sensitive and Rapid Detection of Citrus Scab Using an RPA-CRISPR/Cas12a System Combined with a Lateral Flow Assay

Citrus is the most extensively produced fruit tree crop in the world and is grown in over 130 countries. Fungal diseases in citrus can cause significant losses in yield and quality. An accurate diagnosis is critical for determining the best management practices and preventing future losses. In this study, a Recombinase polymerase amplification (RPA)-clustered regularly interspaced short palindromic repeats (CRISPR)/associated (Cas) system was established with the integration of a lateral flow assay (LFA) readout system for diagnosis of citrus scab. This detection can be completed within 1 h, is highly sensitive and prevents cross-reactions with other common fungal citrus diseases. Furthermore, the detection system is compatible with crude DNA extracted from infected plant tissue. This RPA-CRISPR/Cas12a-LFA system provides a sensitive, rapid, and cost-effective method with promising and significant practical value for point-of-care diagnosis of citrus scab. To our knowledge, this is the first report to establish an RPA- and CRISPR-based method with LFA for fungal diseases in plants.

A Rapid and Sensitive Detection Method for Pseudomonas aeruginosa Using Visualized Recombinase Polymerase Amplification and Lateral Flow Strip Technology

Pseudomonas aeruginosa is a common opportunistic pathogen that causes acute nosocomial necrotizing pneumonia and is the predominant source of chronic lung infections in patients with the genetic disorder cystic fibrosis. Early diagnosis in infected patients and monitoring P. aeruginosa contamination is therefore of great importance in controlling disease spread and development with timely drugs intervention treatment and cut off infection source. Traditional culture-biochemical methods are time consuming and highly dependent on technicians and expensive instruments. To address these challenges, the present study aimed to develop a rapid, sensitive, and specific, on-site detection method for P. aeruginosa based on recombinase polymerase amplification (RPA) combined with lateral flow strip (LFS) technology. The experimental process included screening and modification of primer and probe sets targeting the unique virulence gene elastase B (lasB); specificity detection in 29 strains of P. aeruginosa and 23 closely-related pathogenic bacteria; sensitivity measurements with gradient-diluted P. aeruginosa genomic DNA and probit regression analysis; and clinical application evaluation using 574 patients samples and calculating coincidence rate and kappa index value in comparison with the culture-biochemical method. The P. aeruginosa RPA-LFS assay could complete the amplification process at 37°C constant temperature within 30 min and results could be visualized by the naked eye within 10 min on LFS. The assay displayed high sensitivity with a limit of detection of 3.05 CFU/reaction. It also demonstrated high specificity by showing no cross reaction with other pathogenic bacteria, and rapidness by being completed in less than an hour. Furthermore, when used with clinical samples, the assay had a coincidence rate of 98.26% with the culture-biochemical method and a kappa index value of 0.9433. These data indicate that the RPA-LFS assay represents a major improvement for P. aeruginosa detection, especially in resource-limited areas.

Polydopamine aggregation: A novel strategy for power-free readout of loop-mediated isothermal amplification integrated into a paper device for multiplex pathogens detection

Loop-mediated isothermal amplification (LAMP) has been widely used for detecting pathogens. However, power-free and clear visualization of results still remain challenging. In this study, we developed a paper device integrated with power-free DNA detection strategy realized by polydopamine aggregation. In the presence of DNA amplicons, the polymerization of dopamine into aggregated polydopamine was hindered, while in the absence of DNA amplicons, polydopamine aggregation is facilitated. The porosity of the paper enabled the capillary flow of dispersed polydopamine for positive sample, while aggregated polydopamine remained at the bottom of the paper strip due to large size of the aggregates for negative sample. Based on this mechanism, we fabricated a slidable paper device integrating LAMP with dopamine polymerization for the naked-eye detection, operated in a seamless manner. Moreover, the introduced paper device was successfully used to detect DNA extracted from Escherichia coli O157:H7 and SARS-CoV-2 within 25 min, as well as Enterococcus faecium within 35 min. The detection limits of both Escherichia coli O157:H7 and SARS-CoV-2 were 10^-4 ng/μL. The introduced paper device can be used as a simple and sensitive tool for detecting multiple infectious pathogens, making it an ideal tool particularly for resource-limited environment.

Molecular Detection of Feline Coronavirus Based on Recombinase Polymerase Amplification Assay

Feline coronavirus (FCoV) is endemic in cat populations worldwide. Persistently, subclinically infected cats play a significant role in spreading the infection. Testing fecal samples of cats may facilitate efforts to decrease the viral burden within a population. Real-time RT-PCR is highly sensitive and specific for the detection of FCoV but must be performed in a fully equipped laboratory. A simple and accurate assay is needed to identify FCoV at the point-of-need. The aim of this study was to develop a rapid FCoV detection assay based on isothermal amplification technology, i.e., reverse transcription-recombinase polymerase amplification (RT-RPA). Primers were designed to target the highly conserved 3′ untranslated region of the 7b gene. Running on a constant temperature of 42 °C, reverse transcription as well as DNA amplification and detection was achieved in a maximum of 15 min. A probit analysis revealed a detection limit of 58.5 RNA copies/reaction. For cross-detection, nucleic acids from 19 viruses were tested. Both RT-RPA and real-time RT-PCR showed cross-detection with canine coronavirus and transmissible gastroenteritis virus, but not with other pathogens. To evaluate clinical performance, RNA was extracted from 39 fecal samples from cats. All samples were tested simultaneously with real-time RT-PCR resulting in a RT-RPA sensitivity and specificity of 90.9% and 100%, respectively. RT-RPA can be considered a promising simple method for rapid detection of FCoV.

Evaluation of molecular assays to detect Leishmania donovani in Phlebotomus argentipes fed on post-kala-azar dermal leishmaniasis patients

BACKGROUND

Post-kala-azar dermal leishmaniasis (PKDL) caused by Leishmania donovani (LD) is a skin disorder that often appears after treatment of visceral leishmaniasis (VL) patients. PKDL patients are potential reservoirs of LD parasites, which can initiate a new epidemic of anthroponotic VL. Therefore, host infectiousness to its sand fly vector is a critical factor for transmission, and its accurate estimation can facilitate control strategies. At present, conventional microscopy serves as the reference method to detect parasites in its vector. However, low sensitivity of microscopy can be a limiting factor.

METHODS

In this study, real-time quantitative PCR (LD-qPCR) and recombinase polymerase amplification (LD-RPA) assays were evaluated against microscopy for the detection of LD DNA extracted from live sand flies five days after controlled feeding on PKDL cases.

RESULTS

The sensitivity of LD-qPCR and LD-RPA assays were found to be 96.43 and 100%, respectively, against microscopy for the selected fed sand flies (n = 28), and an absolute specificity of both molecular tools for apparently unfed sand flies (n = 30). While the proportion of infectious cases among 47 PKDL patients was estimated as 46.81% as defined by microscopic detection of LD in at least one fed sand fly per case, LD-RPA assay evaluation of only the microscopy negative sand flies fed to those 47 PKDL cases estimated an even greater proportion of infectious cases (51.06%). In overall estimation of the infectious cases in retrospective manner, discordance in positivity rate was observed (p < 0.05) between LD-RPA (59.57%) assay and microscopy (46.81%), while LD-RPA had slightly better positivity rate than LD-qPCR (55.32%) as well.

CONCLUSIONS

Considering the sensitivity, cost, detection time, and field applicability, RPA assay can be considered as a promising single molecular detection tool for investigations pertaining to LD infections in sand flies and/or host infectiousness in PKDL, while it can also be useful in confirmation of microscopy negative sand fly samples.

Establishment of a visualized isothermal nucleic acid amplification method for on-site diagnosis of acute hepatopancreatic necrosis disease in shrimp farm

Acute hepatopancreatic necrosis disease (AHPND) is a significant deadly infectious disease in the shrimp farming industry, causing serious economic losses globally every year. Because of the rapid progress speed, lack of effective treatment and high mortality rate of AHPND, monitoring with frequent diagnostic tests is vital for a successful prevention. The conventional histopathological diagnosis fell far short of the requirement for efficient monitoring, and the polymerase chain reaction (PCR)-based molecular diagnostic methods that rely on sophisticated thermocycler and trained personnel are hardly applicable in the field. Combining the recombinase polymerase amplification (RPA) and the lateral flow strips (LFSs), a diagnostic method suitable for on-site everyday monitoring of AHPND has been established in this study. This RPA-LFS method targeted the binary toxic photorhabdus insect-related genes PirA and PirB on a virulence plasmid of the AHPND-causative Vibrio parahaemolyticus strains. The diagnostic test was completed within 30 min at 37°C and showed good specificity and good sensitivity of 20 fg DNA of the AHPND shrimp or one colony-forming unit of the causative bacterium per reaction, which was better than the administration-approved standard AP4 assay. Crude templates from sample boiling could be directly used. Tests of clinical samples showed 100% consistency of this method with the standard AP4 assay. This RPA-LFS method can be a good choice for on-site diagnosis of AHPND with quick response time, easy procedure and low demand for resources, and should have significant value for the control of spreading of this dangerous disease in farmed shrimp.

Loop-Mediated Isothermal Amplification Detection of SARS-CoV-2 and Myriad Other Applications

As the second year of the COVID-19 pandemic begins, it remains clear that a massive increase in the ability to test for SARS-CoV-2 infections in a myriad of settings is critical to controlling the pandemic and to preparing for future outbreaks. The current gold standard for molecular diagnostics is the polymerase chain reaction (PCR), but the extraordinary and unmet demand for testing in a variety of environments means that both complementary and supplementary testing solutions are still needed. This review highlights the role that loop-mediated isothermal amplification (LAMP) has had in filling this global testing need, providing a faster and easier means of testing, and what it can do for future applications, pathogens, and the preparation for future outbreaks. This review describes the current state of the art for research of LAMP-based SARS-CoV-2 testing, as well as its implications for other pathogens and testing. The authors represent the global LAMP (gLAMP) Consortium, an international research collective, which has regularly met to share their experiences on LAMP deployment and best practices; sections are devoted to all aspects of LAMP testing, including preanalytic sample processing, target amplification, and amplicon detection, then the hardware and software required for deployment are discussed, and finally, a summary of the current regulatory landscape is provided. Included as well are a series of first-person accounts of LAMP method development and deployment. The final discussion section provides the reader with a distillation of the most validated testing methods and their paths to implementation. This review also aims to provide practical information and insight for a range of audiences: for a research audience, to help accelerate research through sharing of best practices; for an implementation audience, to help get testing up and running quickly; and for a public health, clinical, and policy audience, to help convey the breadth of the effect that LAMP methods have to offer.

Rapid Extraction and Detection of African Swine Fever Virus DNA Based on Isothermal Recombinase Polymerase Amplification Assay

African swine fever virus (ASFV) is the causative agent of a deadly disease in pigs and is spread rapidly across borders. Samples collected from suspected cases must be sent to the reference laboratory for diagnosis using polymerase chain reaction (PCR). In this study, we aimed to develop a simple DNA isolation step and real-time recombinase polymerase amplification (RPA) assay for rapid detection of ASFV. RPA assay based on the p72 encoding B646L gene of ASFV was established. The assays limit of detection and cross-reactivity were investigated. Diagnostic performance was examined using 73 blood and serum samples. Two extraction approaches were tested: silica-column-based extraction method and simple non-purification DNA isolation (lysis buffer and heating, 70 °C for 20 min). All results were compared with well-established real-time PCR. In a field deployment during a disease outbreak event in Uganda, 20 whole blood samples were tested. The assay’s analytical sensitivity was 3.5 DNA copies of molecular standard per µL as determined by probit analysis on eight independent assay runs. The ASFV RPA assay only detected ASFV genotypes. Compared to real-time PCR, RPA diagnostic sensitivity and specificity were 100%. Using the heating/lysis buffer extraction procedure, ASFV-RPA revealed better tolerance to inhibitors than real-time PCR (97% and 38% positivity rate, respectively). In Uganda, infected animals were identified before the appearance of fever. The ASFV-RPA assay is shown to be as sensitive and specific as real-time PCR. Moreover, the combination of the simple extraction protocol allows its use at the point of need to improve control measures.

RPAcan3990: an Ultrasensitive Recombinase Polymerase Assay To Detect Angiostrongylus cantonensis DNA

Angiostrongylus cantonensis is one of the leading causes of eosinophilic meningitis worldwide. A field-deployable molecular detection method could enhance both environmental surveillance and clinical diagnosis of this emerging pathogen. Accordingly, RPAcan3990, a recombinase polymerase assay (RPA), was developed to target a region predicted to be highly repeated in the A. cantonensis genome. The assay was then adapted to produce a visually interpretable fluorescent readout using an orange camera lens filter and a blue light. Using A. cantonensis genomic DNA, the limit of detection was found to be 1 fg/μl by both fluorometer measurement and visual reading. All clinical samples known to be positive for A. cantonensis from various areas of the globe were positive by RPAcan3990. Cerebrospinal fluid samples from other etiologies of eosinophilic meningitis (i.e., Toxocara sp. and Gnathostoma sp.) were negative in the RPAcan3990 assay. The optimal incubation temperature range for the reaction was between 35°C and 40°C. The assay successfully detected 1 fg/μl of A. cantonensis genomic DNA after incubation at human body temperature (in a shirt pocket). In conclusion, these data suggest RPAcan3990 is potentially a point-of-contact molecular assay capable of sensitively detecting A. cantonensis by producing visually interpretable results with minimal instrumentation.

Development of robust isothermal RNA amplification assay for lab-free testing of RNA viruses

Simple tests of infectiousness that return results in minutes and directly from samples even with low viral loads could be a potential game-changer in the fight against COVID-19. Here, we describe an improved isothermal nucleic acid amplification assay, termed the RICCA (RNA Isothermal Co-assisted and Coupled Amplification) reaction, that consists of a simple one-pot format of ‘sample-in and result-out’ with a primary focus on the detection of low copy numbers of RNA virus directly from saliva without the need for laboratory processing. We demonstrate our assay by detecting 16S rRNA directly from E. coli cells with a sensitivity as low as 8 CFU/μL and RNA fragments from a synthetic template of SARS-CoV-2 with a sensitivity as low as 1740 copies/μL. We further demonstrate the applicability of our assay for real-time testing at the point of care by designing a closed format for paper-based lateral flow assay and detecting heat-inactivated SARS-COV-2 virus in human saliva at concentrations ranging from 28,000 to 2.8 copies/μL with a total assay time of 15–30 min.

Nonspecific Synthesis in the Reactions of Isothermal Nucleic Acid Amplification

The review focuses on the main factors involved in the formation of nonspecific products in isothermal nucleic acid amplification, such as mispriming, ab initio DNA synthesis, and additional activities of DNA polymerases, and discusses approaches to prevent formation of such nonspecific products in LAMP, RPA, NASBA, RCA, SDA, LSDA, NDA, and EXPAR.

Development of a Multiplex High-Throughput Diagnostic Assay for the Detection of Strawberry Crown Rot Diseases Using High-Resolution Melting Analysis

Rapid and accurate disease diagnosis is a prerequisite for an effective disease management program in strawberry production. In Florida, Colletotrichum spp., Phytophthora spp., and Macrophomina phaseolina are the primary microorganisms causing strawberry crown rot. Even though the diseases can be caused by different pathogens, symptoms are indistinguishable and equally devastating. To inform strawberry growers in a timely fashion of diagnostic results for effective deployment of chemical control practices, we developed a multiplex high-resolution melting (HRM) assay to rapidly and accurately detect the abovementioned pathogens. The multiplex HRM assays using three predesigned primer pairs showed high specificity for individual species by generating specific melting peaks without cross-reaction between primers or with other common strawberry pathogens. The amplification limit of the assay was 1 pg of Colletotrichum and Phytophthora and 100 pg of M. phaseolina DNA per 10-μl reaction. However, the presence of different melting peaks was observed in mixed DNA samples and was concentration and target DNA dependent. A crude DNA extraction protocol was developed to allow high-throughput screening by minimizing the inhibitory effects. Moreover, we applied the HRM assay to 522 plant samples and found high correlations between conventional pathogen isolation and HRM and between singleplex and multiplex assays. Altogether, this multiplex HRM assay is specific, cost effective, and reliable for the timely detection of strawberry crown rot pathogens.

Isothermal amplifications - a comprehensive review on current methods

The introduction of nucleic acid amplification techniques has revolutionized the field of medical diagnostics in the last decade. The advent of PCR catalyzed the increasing application of DNA, not just for molecular cloning but also for molecular based diagnostics. Since the introduction of PCR, a deeper understanding of molecular mechanisms and enzymes involved in DNA/RNA replication has spurred the development of novel methods devoid of temperature cycling. Isothermal amplification methods have since been introduced utilizing different mechanisms, enzymes, and conditions. The ease with which isothermal amplification methods have allowed nucleic acid amplification to be carried out has had a profound impact on the way molecular diagnostics are being designed after the turn of the millennium. With all the advantages isothermal amplification brings, the issues or complications surrounding each method are heterogeneous making it difficult to identify the best approach for an end-user. This review pays special attention to the various isothermal amplification methods by classifying them based on the mechanistic characteristics which include reaction formats, amplification information, promoter, strand break, and refolding mechanisms. We would also compare the efficiencies and usefulness of each method while highlighting the potential applications and detection methods involved. This review will serve as an overall outlook on the journey and development of isothermal amplification methods as a whole.

New DNA-hydrolyzing DNAs isolated from an ssDNA library carrying a terminal hybridization stem

DNA-hydrolyzing DNAs represent an attractive type of DNA-processing catalysts distinctive from the protein-based restriction enzymes. The innate DNA property has enabled them to readily join DNA-based manipulations to promote the development of DNA biotechnology. A major in vitro selection strategy to identify these DNA catalysts relies tightly on the isolation of linear DNAs processed from a circular single-stranded (ss) DNA sequence library by self-hydrolysis. Herein, we report that by programming a terminal hybridization stem in the library, other than the previously reported classes (I & II) of deoxyribozymes, two new classes (III & IV) were identified with the old selection strategy to site-specifically hydrolyze DNA in the presence of Zn²⁺. Their representatives own a catalytic core consisting of ∼20 conserved nucleotides and a half-life of ∼15 min at neutral pH. In a bimolecular construct, class III exhibits unique broad generality on the enzyme strand, which can be potentially harnessed to engineer DNA-responsive DNA hydrolyzers for detection of any target ssDNA sequence. Besides the new findings, this work should also provide an improved approach to select for DNA-hydrolyzing deoxyribozymes that use various molecules and ions as cofactors.

Assessment and Management of Diabetic Patients During the COVID-19 Pandemic

COVID-19 has become a great challenge across the globe, particularly in developing and densely populated countries, such as India. COVID-19 is extremely infectious and is transmitted via respiratory droplets from infected persons. DM, hypertension, and cardiovascular disease are highly prevalent comorbidities associated with COVID-19. It has been observed that COVID-19 is associated with high blood-glucose levels, mainly in people with type 2 diabetes mellitus (T2DM). Several studies have shown DM to be a significant risk factor affecting the severity of various kinds of infection. Dysregulated immunoresponse found in diabetic patients plays an important role in exacerbating severity. DM is among the comorbidities linked with mortality and morbidity in COVID-19 patients. Chronic conditions like obesity, cardiovascular disorders, and hypertension, together with changed expression of ACE2, dysregulated immunoresponse, and endothelial dysfunction, may put diabetic patients at risk of greater COVID-19 severity. Therefore, it is important to study specific characteristics of COVID-19 in diabetic people and treat these comorbidities along with COVID-19 infection, mainly among old individuals who are already suffering from serious and critical infections. This review will be helpful in understanding the mechanisms involved in COVID-19 and DM, the role of ACE2 in COVID-19 pathogenesis, management of DM, and associated complications in COVID-19 patients.