Predicting anaerobic biogasification potential of ingestates and digestates of a full-scale biogas plant using chemical and biological parameters

Exploring increased hydraulic retention time as a cost-efficient way of valorizing residual biogas potential

Effective substrate utilization with low residual methane yield in the digestate is crucial for the economy and sustainability of biogas plants. The composition and residual methane potential of 29 digestate samples from plants operating at hydraulic retention times of 13-130 days were determined to evaluate the economic viability of extended digestion. Considerable contents of fermentable fractions, such as cellulose (8-23%), hemicellulose (1-18%), and protein (13-22%), were present in the digestate dry matter. The ultimate residual methane yields varied between 55 and 236 ml/g of volatile solids and correlated negatively with the logarithm of the hydraulic retention time (r = -0.64, p < 0.05). Economic analysis showed that extending the retention time in 20 days would be viable for 18 systems if methane were sold for 1.00 €/m3, with gains up to 40 €/year/m3 of newly installed reactor capacity. The results show the importance of operating at sufficient hydraulic retention time.

Anaerobic co-digestion of coffee waste with other organic substrates: A mixture experimental design

The viability of the anaerobic co-digestion of coffee waste (CFW) with other organic waste (cow manure-CM, food waste-FW, anaerobic sludge-AS) was investigated through measurements of biogas generation of various mixtures of the above substrates. The experiments were designed following the principles of mixture experimental design. Four different mixtures were tested anaerobically at 37 °C in 500 mL and 1 L anaerobic vessels. AS was used in some mixtures as an inoculum. The results were fitted to two empirical models in which biogas generation was the dependent variable and the fractions of the components in the mixture were the independent variables. According to the empirical models, the co-digestion of CFW with AS appeared to have a positive (synergistic) effect, generating 201 mL g^-1 VS_mixture, which was 12% higher than the amount generated from the mono-digestion of AS (179 mL g^-1 VS). On the other hand, the co-digestion of CFW with CM and of CFW with FW had a negative (antagonistic) effect on biogas generation indicating that CFW inhibits biogas generation when mixed with CM and FW. Although the mono-digestion of CM resulted in an average of 149 mL g^-1 VS of biogas, when CM was combined with CFW in a mixture, biogas generation was highly reduced by 43.8%-85.1%, depending on the CFW content of the mixtures, which was 25% and 50%, respectively. When co-digesting CFW with FW, the biogas generated was 7.02 mL g^-1 VS that was obtained only from the FW in the mixture.

Assessing the anaerobic degradability and the potential recovery of biomethane from different biodegradable bioplastics in a full-scale approach

The aim of the present study was to evaluate the anaerobic degradability and the potential recovery of biomethane from different bioplastics using a full-scale approach. Bioplastics were placed inside a real anaerobic digestion plant working under thermophilic conditions and quantitative and qualitative degradation of bioplastics was evaluated. Laboratory-scale experiments were used to determine the amount of biomethane produced by anaerobic degradation of bioplastics. Polylactic acid-based items may degrade completely using retention times compatible with anaerobic digestion plants contributing positively to biomethane production, i.e., in 90 days 397 ± 8 NL CH₄ kg_{volatile solids}^-1 were produced by polylactic acid-based cutlery. Starch-based shoppers showed a quick degradation of the starch component in the first month of anaerobic digestion, followed by a slow degradation of the polyester component. Anaerobic digestion and/or anaerobic digestion coupled to digestate composting may represent the best strategy to dispose these wastes meeting the principles of Circular Economy.

Using highly stabilized digestate and digestate-derived ammonium sulphate to replace synthetic fertilizers: The effects on soil, environment, and crop production

Recovered fertilizers (a highly stabilized digestate and ammonium sulphate) obtained from anaerobic digestion of sewage sludge, were used on plot trials with a maize crop, in a comparison with synthetic fertilizers. After three consecutive cropping seasons, the soils fertilized with the recovered fertilizers (RF), compared to those fertilized with synthetic fertilizers (SF), did not show significant differences either in their chemical characteristics or in the accumulation of inorganic and organic pollutants (POPs). The RF ensured an ammonia N availability in the soil equal to that of the soil fertilized with SF, during the whole period of the experiment. Furthermore, no risks of N leaching were detected, and the use of RF did not result in a greater emission of ammonia or greenhouse gases than the use of SF. The agronomic results obtained using RF were equivalent to those obtained with SF (fertilizer use efficiency of 85.3 ± 10 and 93.6 ± 4.4% for RF and SF respectively). The data show that utilising a very stable digestate can be a good strategy to produce a bio-based fertilizer with similar performance to that of a synthetic fertilizer, without environmental risks.

The structure and diversity of microalgae-microbial consortia isolated from various local organic wastes

Pure microalgae cultivation in organic wastes may be hampered by their low adaptation to extreme growth conditions and by the risk of microbial contamination. This work aimed to isolate self-adapted microalgae-microbial consortia able to survive in organic wastes characterized by extreme conditions, to be then proposed for technological application in removing carbon and nutrients from wastes' streams. To do so, sixteen organic wastes with different origins and consistency were sampled. Twelve microbial consortia were isolated from wastes and their eukaryotic and prokaryotic compositions were analyzed by next generation sequencing. Eight eukaryotic communities were dominated by Chlorophyta, led by Chlorella, able to survive in different wastes regardless of chemical-biological properties. Tetradesmus, the second most represented genus, grew preferentially in substrates with less stressing chemical-physical parameters. Chlorella and Tetradesmus were mostly isolated from cow slurry and derived wastes which proved to be the best local residual organic source.

The link between organic matter composition and the biogas yield of full-scale sewage sludge anaerobic digestion

The principal parameters influencing anaerobic digestion (AD) of sewage sludge have been extensively studied in controlled laboratory experiments, but the effects of sludge composition on full-scale systems have received relatively little attention. Sludge samples from eight major wastewater treatment plants (WWTPs) in the UK were examined to determine the effects of sludge composition on digestion performance. The biogas yield (BY) was estimated by two different methods: (1) a standard approach based on the reduction in volatile solids (VS), and (2) a more detailed mass balance of major constituent fractions of organic matter in sludge. The results showed that BY increased significantly with the overall amount of VS contained in digester feed sludge. In terms of the effects of individual fractions, BY was significantly related to and increased with the fat and cellulose contents in raw sludge, consistent with the high calorific value of fat and the digestibilities of both substrates, relative to the other major organic components. The results demonstrated the importance of sludge composition on digester performance and strategies to maximise BY were identified, for instance, by increasing codigestion of high fat containing substrates, and by utilising fat, oil and grease collected in-sewer and at WWTP.

Degradation of bioplastics in organic waste by mesophilic anaerobic digestion, composting and soil incubation

The aim of the study was to assess the effects of high concentrations (10 % w/w, data projected for 2030) of commercial bioplastics, i.e. starch based shopping bags (SBSB) and polylactic acid (PLA) tableware, in the organic fraction of municipal solid wastes (MSW) on compost quality obtained by pilot-scale dry mesophilic anaerobic digestion and subsequent composting of the digestate. After the biological processes, 48.1 % total solids (TS) of SBSB and 15 % TS of PLA degraded, resulting in a high bioplastics content (about 18 % TS) in compost. Subsequent compost incubation in soils indicated that bioplastics degraded by pseudo-zero order kinetics (0.014 and 0.010 mg C cm^-2 d^-1 for SBSB and PLA, respectively), i.e. complete degradation was expected in 1.6 years (SBSB) and 7.2 years (PLA), confirming the intrinsic biodegradability of bioplastics. Nevertheless, enhancing the rate and amount of bioplastics degradation during waste management represents a goal to decrease the amount of bioplastics reaching the environment.

Estimation of long-term methane emissions from Mechanical-Biological Treatment waste through biomethane potential test

Mechanical-Biological Treatment (MBT) is a technology applied to reduce the environmental impacts of urban waste based on stabilizing the organic matter content. As the process is not entirely efficient, the residue can generate methane when it is landfilled. Long-term methane emissions estimation based on models is usually over or underestimated because the actual waste composition after stabilization is generally unknown. This work proposes a single tool to improve the emission estimations of the landfilled MBT waste based on the determination of the biomethane potential test (BMP). Experimental BMP of the crude and stabilized organic fractions of municipal solid waste obtained from an MBT plant were carried out, and the results were used to predict the methane emission from two models, LandGEM (2005) and IPCC (2006). In the LandGEM model, the experimental value of BMP represents the methane potential L0 while in the IPCC model it allowed to obtain the ultimate organic carbon anaerobically degraded (DOCf), based on a linear correlation (R2 = 0.944, p-value < .05) that can be used to obtain the DOCf in a waste of any composition. The results of the long-term (40 years) methane emissions of the stabilized waste disposed on land showed overestimations of up 56.0% (IPCC model) and 259.5% (Landgem model) when default data, instead the actual DOCf were applied in stabilized waste; similar behaviour was observed for the crude waste (23.3% and 241.3% overestimations). Moreover, the impact of the stabilization process revealed methane emission reductions of 5.1% and 20.9% based on LandGEM and IPCC models, respectively.

Silage of the organic fraction of municipal solid waste to improve methane production

The silage of the organic fraction of municipal solid waste (OFMSW) is a common practice in biogas plants. During silage, fermentation processes take place, affecting the later methanisation stage. There are no studies about how OFMSW silage affects methane production. This work aimed to determine the effects of silage (anaerobic acid fermentation) at different solids concentrations and temperatures on methane production. OFMSW was ensiled at 20, 35, and 55 °C with total solids (TS) concentrations of 10, 20, and 28% for 15 days. The ensiled OFMSW was then tested for methane production at the substrate to inoculum ratios (S/I) of 0.5, 1.0, and 1.5. Independently of the temperature, the production of the metabolites during silage increases with decreasing solids concentration. The highest production was of lactic acid, ethanol, and acetic acid, representing together 95% of the total. Methane production from ensiled OFMSW at 10% solids concentration shows, under every tested condition, better methane production than from fresh OFMSW. Ensiled OFMSW produces more methane than fresh OFMSW, and methane production was highest at 35 °C.

Thermophilic anaerobic digestion as suitable bioprocess producing organic and chemical renewable fertilizers: A full-scale approach

This work reports a full-scale study in which organic wastes were transformed by high-solid thermophilic anaerobic digestion (HSAD), into N fertilizers and organic fertilizers, i.e. digestate. The produced fertilizers were characterized over 42 months and their properties were discussed in comparisons with literature data. HSAD coupled with N stripping technology led to ammonia sulphate production having high N concentration (74 ± 2 g kg^-1 wet weight), neutral pH (6.8 ± 1.3) and low traces of other elements. Digestate showed both higher carbon (C) content (314 ± 30 g kg^-1 on dry matter (DM) and biological stability than green composts, indicating good amendment properties. Digestate was also interesting for its N (77 ± 3.7 g kg^-1 dry matter - DM) content, half of it in the ammonia form, and P content (28 ± 4.1 g kg^-1 DM) that was 43% readily available as soluble P-orthophosphate. K content was low (6.5 ± 1.3 g kg^-1 DM), indicating poor fertilizing ability of digestate for this element. All organic pollutants investigated were much lower than the limits required for agricultural use and levels of some of them were lower than the content revealed for other organic matrices such as agricultural and energy crop digestates and compost. Emerging pollutants (i.e., pharmaceuticals) were tested as markers and they were found to be below the detection limit (<0.01 mg kg^-1 DM) indicating very low content. The results obtained showed that HSAD coupled with N stripping allowed transforming sewage sludge into fertilizers and soil improvers exploitable in agriculture.

Assessment of Fruit and Vegetable Residues Suitable for Renewable Energy Production: GIS-Based Model for Developing New Frontiers within the Context of Circular Economy

Due to the necessity of developing renewable energy sources, the anaerobic digestion for producing biomethane has developed significantly in the last years, since it allows to both reduce disposal treatment and produce green energy. In this field, fruit and vegetable wastes have been recently put forward, since they could represent a suitable resource for producing biomethane as a new frontier within the context of a circular economy. This study aims at filling the gap in the knowledge of the production, quantities and biogas potential production of these residues. On this basis, a GIS-based model was developed and applied to the Sicily region by investigating the specific regulatory framework as well as by analysing descriptive statistics. The results of the GIS analyses enabled the localisation of the highest productive territorial areas and highlighted where fruit and vegetable wastes are abundantly located. In this regard, about 7 million Nm3 of biogas could be produced by reusing only the fruit and vegetable residues coming from the three most representative Sicilian wholesale markets among those considered. Finally, the regulatory framework is of crucial importance in inhibiting or supporting the use of the selected biomass in a specific sector, with regard to the case study considered.

Enhancement of Anaerobic Digestion of Waste-Activated Sludge by Conductive Materials under High Volatile Fatty Acids-to-Alkalinity Ratios

Anaerobic digestion (AD) represents a suitable option for the management of the waste-activated sludge (WAS) produced in municipal wastewater treatment plants. Nevertheless, due to its complex characteristics, WAS is often barely degradable under conventional anaerobic processes. The use of conductive materials during AD provides a promising route for enhancing WAS digestion, through the effects of direct inter-species electron transfer (DIET). The present paper aims to evaluate the effects of the addition of four different materials—granular activated carbon (GAC), granular iron, and aluminium and steel scrap powders—in semi-continuous lab-scale reactors under very high volatile fatty acids-to-alkalinity ratios. In particular, the use of metallic aluminium in WAS digestion was investigated for the first time and compared to the other materials. The AD of WAS without the addition of conductive materials was impossible, while the use of steel powder and zero-valent iron is shown not to improve the digestion process in a satisfactory way. On the contrary, both GAC and Al allow for effective WAS degradation. At stable conditions, methane yields of about 230 NmLCH4/gVS and 212 NmLCH4/gVS are recorded for GAC- and Al-amended reactors, respectively. These two materials are the most promising in sustaining WAS AD through DIET also in case of unbalanced volatile fatty acids-to-alkalinity ratios.

Biological denitrification potential as an indicator for measuring digestate stability

Biological stability is an essential parameter for assessing the environmental impact from the land application of digestate as organic amendment. In this paper, a new indicator, biological denitrification potential (BDP), was developed for evaluating the biological stability of digestate. Digestate samples collected along the digestion process from a mesophilic anaerobic batch digester fed with food waste were investigated under different solid retention time. The value of BDP based on nitrate removal ranged from 176.3 to 48.3 mg-N/g-VS_digestate, corresponding well to the digestion time, and strongly correlated with total organic carbon content. Evolution trends similar to respiration index (RI) and biochemical methane potential (BMP) can be also observed for BDP, indicating that values presented of these stability indices decreased with the degree of digestate stabilization. The mass balance of the BDP process indicated that nitrate was mainly converted into N₂ gas with mineralizing organic carbon from digestate, implying that biostability evaluated by BDP depends on carbon source and denitrification activity in digestate. The denitrifying bacteria Thiopseudomonas and Pseudomonas accounted for the majority of microorganisms. These findings of this study concluded that BDP can be an efficient indicator to assess the bio-stability of digestate planned for agricultural or land use. Compared with the existing biostability index, BDP has the additional advantage of no exogenous inoculum addition, homogenous test condition and possibility of shortening incubation time.

Preliminary evaluation of the anaerobic biodegradability of three biobased materials used for the production of disposable plastics

Biodegradable plastics have been introduced to the market to substitute "traditional", non-biodegradable, petro-based plastics to alleviate plastic pollution. Biochemical methane potential tests were carried out on compostable bags made of MaterBi®, biodegradable bottle wine corks and cellulosic plates to examine the anaerobic biodegradability of those materials. The impact of four factors: type of pretreatment (predigestion, mechanical, alkaline, predigestion and alkaline), digestion duration, type of inoculum and temperature were statistically evaluated through regression modeling. Anaerobic tests on compostable and polyethylene bags (control) were carried out in mesophilic (35 °C) and thermophilic (55 °C) conditions, while tests on bottle wine corks and cellulosic plates were carried out in mesophilic conditions only. After 15 days of digestion, a dry mass reduction of 22.8 ± 6.2 % and 27.6 ± 14.0 % for mesophilic and thermophilic tests respectively was recorded for MaterBi®. Chemical pretreatment with NaOH led to a mass reduction of 78.2 ± 7.2 % and was the only statistically significant factor to affect both methane yields and dry mass loss. A higher digestion temperature led to an increased mass loss without a concurrent increase in methane production. The cellulosic plates were completely degraded (99.9 ± 0.03 % mass reduction), while the wine bottle corks weight did not change.

Removal of polycyclic aromatic hydrocarbons during anaerobic biostimulation of marine sediments

This study proposes the supplementation of digestate, fresh organic fraction of municipal solid waste (OFMSW) and a nutrient solution during the anaerobic biostimulation of marine sediments contaminated by polycyclic aromatic hydrocarbons (PAHs). The experimental activity was conducted with four PAHs (i.e. phenanthrene, anthracene, fluoranthene and pyrene) under controlled mesophilic conditions (37 ± 1 °C) in 100 mL serum bottles maintained at 130 rpm. After 120 days of incubation, the highest total PAH degradation of 53 and 55% was observed in the experiments with digestate + nutrients and OFMSW + nutrients, respectively. Phenanthrene was the most degraded PAH and the highest removal of 69% was achieved with OFMSW + nutrients. The anaerobic PAH degradation proceeded through the accumulation of volatile fatty acids and the production of hydrogen and methane as biogas constituents. The highest cumulative biohydrogen production of 80 mL H₂·g VS^-1 was obtained when OFMSW was used as the sole amendment, whereas the highest biomethane yield of 140 mL CH₄·g VS^-1 was obtained with OFMSW + nutrients. The evolution of PAH removal during anaerobic digestion revealed a higher impact of the methanogenic phase rather than acidogenic phase on PAH degradation.

An improved procedure to assess the organic biodegradability and the biomethane potential of organic wastes for anaerobic digestion

In this study a fractionation procedure was developed and applied to evaluate the potential of some organic wastes (two cattle manures and two catch crops, fresh and after ensiling) for anaerobic digestion. This procedure was based on water extraction of the raw sample, which enabled the evaluation of the contributions of water-soluble and particulate phases to the investigated properties. Biomethane potential (BMP) and chemical oxygen demand (COD) were determined and used to assess the anaerobic biodegradability of raw materials. Analysis of structural carbohydrates, total Kjeldahl nitrogen, water-soluble carbohydrates, volatile fatty acids and pH were also included to explain the main phenomena involved in methane production from the tested biomass. Results show that the origin and the preparation mode had a significant impact on BMP distribution. Based on a COD balance, the biodegradability of the various feedstocks ranged from 45% to 75%. Biodegradability of fresh materials was negatively correlated with the sum of structural carbohydrates and lignin content. Among the feedstock used, the water-soluble phase represented 8-69% of the total COD and 7-46% to the total BMP. Solubilization of organic matter during ensiling was due to the production and accumulation of organic acids from particulate carbohydrates and organic nitrogen. This procedure detects kinetic and biodegradability differences among biomass and thus it can be useful for the design of anaerobic digestion plants. Furthermore, it can be applied to evaluate the efficiency of biomass pretreatments.

The Evaluation of Indicators Used to Assess the Suitability of Agricultural Waste for Fermentation

To ensure high fermentation efficiency, it is necessary to assess the biodegradability of a substrate. These parameters are most often determined on the basis of the amount of loss on ignition and total organic carbon. We are more and more often using chemical indices. However, these indices do not provide information on how much an organic substance is susceptible to biodegradation. The actual assessment of the content of easily biodegradable matter in substrates that are used for fermentation should be performed on the basis of aerobic (AT4) and anaerobic tests (BMP), which require specialised equipment and are time consuming. The AT4 index is being more and more frequently adopted for the analysis of substrates that are used in the fermentation process, because AT4 takes a much shorter time than BMP and provides information on the biodegradability of substrates. The aim of the article is to answer the question of whether the AT4 parameter can be used to assess the suitability of the substrate from the agricultural sector for the fermentation process. The results show that the AT4 index could be used instead of the BMP parameter.

Statistical analysis for the quality assessment of digestates from separately collected organic fraction of municipal solid waste (OFMSW) and agro-industrial feedstock. Should input feedstock to anaerobic digestion determine the legal status of digestate?

Management options for digestate produced by anaerobic digestion plants influence the environmental and economic sustainability of the biogas sector. Further, digestate can be both used or disposed of according to its legal classification: that is, waste or by-product, or product (by using End of Waste procedure). Currently, legal digestate status is decided by EU member states on a case-by-case basis, according to specific positive lists of input feedstocks and quality requirements in terms of physical properties and chemical concentrations. Biased exclusion of input feedstock can force digestate to a specific waste classification and undergo post-treatment and disposal options that can negatively affect the profitability of biogas installations. This is the case of the Italian regulation, where the positive list of input feedstock excludes a priori separately collected organic fractions of municipal solid waste (OFMSW), while including agro-industrial residues (AGRO). This study determined the differences between the two digestate typologies (OFMSW versus AGRO) through statistical analysis, implemented on a dataset, designed to gather data about digestate's physical-chemical parameters from relevant scientific literature and unpublished private databases. The datasets consisted of 190 entries, derived from more than 2,000 samples. Further, the study provided a compliance assessment between the resulting parameter means and the current regulation limits. Upper confidence limits for the means (level of significance α = 0.05) calculated for both digestate typologies were found to be compliant with the legal requirements. Therefore, no statistical ratio seems to support the difference in the legislative approach as proposed by Italian law-makers. OFMSW resulted significantly different from AGRO for VS (650.1 g/kg TS vs. 843.8 g/kg TS, respectively), N-NH4 (81.9 g/kg TS vs. 46.19 g/kg TS), N-TOT (109.7 g/kg TS vs. 65.32 g/kg TS), P-TOT (7.22 g/kg TS vs. 21.9 g/kg TS), Pb (18.6 mg/kg TS vs. 4.66 mg/kg TS), Ni (11.03 mg/kg TS vs. 8.20 mg/kg TS), Cr-TOT (12.74 mg/kg TS vs. 8.74 mg/kg TS) and Hg (0.08 mg/kg TS vs. 0.05 mg/kg TS). However, the statistical analysis must be implemented on a wider set of parameters not covered by this study (e.g. ecotoxicological features).

A comparison of methods for early prediction of anaerobic biogas potential on biologically treated municipal solid waste

Anaerobic gas production tests, generically Biochemical Methane Potential (BMP) or Biogas Potential (BP) tests, are often used to assess biodegradability, though long duration limits their utility. This research investigated whether simple modelling approaches could provide a reliable earlier prediction of total biogas production. Data were assessed from a non-automated biogas test on a large number of both fresh and processed municipal solid waste (MSW) samples, sourced from a mechanical biological treatment (MBT) plant. Non-linear models of biogas production curves were useful in identifying a suitable test endpoint, supporting a test duration of 50 days. Biogas production at 50 days (B₅₀) was predicted using the first 14 days of test data, using (a) linear correlation, (b) a new linearisation process, and (c) non-linear kinetic models. Prediction errors were quantified as relative root mean squared error of prediction (rRMSEP), and bias. Predictions from most models were improved by removing the initial exponential increase phase. Linear correlation gave the most precise and accurate predictions at 14 days (rRMSEP = 2.8%, bias under 0.05%) and allowed acceptable prediction (rRMSEP <10%) both at 8 days, and at 6 days using separate correlations for each sample type. Of the other predictions, the new linearisation process gave the lowest rRMSEP (10.6%) at 14 days. More complex non-linear models conferred no advantage in prediction of B₅₀. These results demonstrate that early prediction of anaerobic gas production is possible for a well-optimised test, using only basic equipment and without recourse to external data sources or complex mathematical modelling.

Development of statistical predictive models for estimating the methane yield of Italian municipal sludges from chemical composition: a preliminary study

The biochemical methane potential (BMP) of primary and biological sludge varies in a wide range, mostly depending on location, sewer characteristics, wastewater treatment plant design and operating conditions. BMP tests are useful to verify the performance of a full scale digester, but they are not yet a common procedure in the operation of most Italian facilities because of cost and test duration. Changes in the composition of sewage sludge can lead to a high variation of biogas production. Aimed at developing BMP predictive models based on low cost and fast analyses, this study investigated the chemical composition of 20 sludge samples by means of principal component and multiple linear regression analyses. Three preliminary predictive models were developed based on soluble organic nitrogen, volatile solids, carbohydrates, proteins, lipids and an operational parameter, the sludge retention time: the explained variance and the standard errors of prediction of BMP are in the range 77-81% and 21-34 NmL_CH4·g_VS ^-1, respectively. Models were evaluated on five additional samples: errors ranged 2-15% for four samples and about 54% for one sample, collected from a peculiar facility. Further data and variables describing the operation mode of the waterline would certainly improve the reliability and robustness of the models.

Biological stability of multi-component agri-food digestates and post-digestates

The use of digestate in agriculture has been an efficient way to mitigate greenhouse gas emissions through the recycling of organic materials. However, harmful effects can arise if the organic matter is unstable. The goal of this study was to determine the biological stability (4-day oxygen demand for degradation of readily biodegradable organic matter (AT4), 21-day anaerobic biogas potential (GP21), and organic matter (VS) content) of six digestates after mesophilic digestion, and that of the corresponding post-digestates after psychrophilic post-digestion. Moreover, the kinetics of the changes in biological stability during post-digestion were determined. Mesophilic digestion of six multi-component agri-food feedstocks consisting of maize silage, bovine manure, mallow silage, pig slurry, glycerin, and spent wash from distillation was carried out at an organic loading rate of 2-3 kg VS/(m³·d), and at a hydraulic retention time of 45-60 days. Digestates were left in stirred reactors, imitating storage digesters, and kept for the next 120 d under anaerobic psychrophilic conditions (20 ± 1 °C) for further stabilization. The additional biogas yields during post-digestion (50.9-114.9 dm³/kg TS) accounted for 8.5-27.4% of the biogas productivity of the feedstocks and 40-80% of that of the digestates. The efficiency of the loss of organic matter content was 22.5-40.2%. The decrease in the values of AT4, GP21 and VS content made the post-digestates more biologically stable than the digestates (digestates: AT4 = 13.7-67.0 mg O₂/g TS, GP21 = 71.5-130.1 dm³/kg TS; post-digestates: AT4 = 6.6-37.4 mg O₂/g TS, GP21 = 15.7-79.2 dm³/kg TS). For digestates and post-digestates, AT4 values strongly correlated with GP21 values.

Use of agricultural by-products in the development of an agro-energy chain: A case study from the Umbria region

Use of agricultural and livestock by-products for anaerobic digestion (AD), in total or partial substitution of the maize silage was evaluated from an environmental and economical point of view. The evaluation process included three methodological interdependent and consequential steps: the chemical stage at laboratory and plant level, the environmental and economic steps developing the Life Cycle Assessment and Life Cycle Costing jointly. The laboratory test showed that the two mixtures prepared with by-products, in partial (MIX A) and total (MIX B) substitution of maize silage, did not show differences in bio-methane production compared to a reference mixture with the 33% of maize silage. All mixtures tested at full-scale plant, showed the same performances, resulting in a similar energy production. Environmentally, MIX B increased greenhouse gas credits derived from the avoided production of mineral fertiliser for the energetic crops, resulting also in better economic performances. The break-even transport distances follow the positive environmental pattern result, in contrast to what was found for the break-even transport distances from the economic point of view.

Strategies for the sustainable management of orange peel waste through anaerobic digestion

The processing of oranges is a major industry worldwide and leads to the production of large amounts of orange peel waste (OPW). Energy production through anaerobic digestion of OPW is a promising option; however, the high content of essential oil, mainly composed of d-limonene, a well-known antioxidant, can cause the inhibition of the biological activity. In this paper, different pretreatment methods were tested (e.g. ensiling, aeration, thermal and alkaline treatments) to optimize the anaerobic digestion of OPW focusing on d-limonene removal. The raw and pretreated substrates were characterized and their biochemical methane production was measured. The results demonstrated the ability of some of the treatments to reduce d-limonene content up to 80%. A relatively high biomethane potential production of OPW (up to about 500 NmL CH₄ g^-1VS) was measured. The importance of the acclimation of inoculum and the risk connected to the accumulation of inhibiting substances in the reactor is discussed.

The feasibility of putrescible components of municipal solid waste for biomethane production at Hyderabad, Pakistan

This study analyzes the feasibility of putrescible components of municipal solid waste (PCMSW) such as food waste (FW) and yard waste (YW) for methane production in Pakistan. The batch experiments have been conducted at two different inoculums to substrate ratios (ISR_s) by using various inoculums under mesophilic condition. The highest methane yield of FW and YW is achieved to be 428 Nml g^-1 volatile solids (VS) added and 304 Nml g^-1 VS added respectively by using buffalo dung inoculum at ISR-5. While, lowest methane yield of FW and YW is obtained as 236 Nml g^-1 VS added and 151Nml g^-1 VS added respectively by using effluent from a continuous stirrer tank reactor as inoculum at ISR-3. The first order decay model has been introduced, which gives best fit for methane potential of PCMSW with buffalo dung inoculum. Additionally, the feasibility of PCMSW in terms of power generation potential has been analyzed. About 60.63 million m³/year energy can be generated by converting PCMSW into methane gas leading to power generation. The finding of this study concludes that the replacement of imported energy and reduction up to 1.62% in other primary energy sources would be achieved, if PCMSW are properly converted into energy through anaerobic digestion in Pakistan.

Effect of three pretreatment techniques on the chemical composition and on the methane yields of Opuntia ficus-indica (prickly pear) biomass

Opuntia ficus-indica (OFI) is an emerging biomass that has the potential to be used as substrate in anaerobic digestion. The goal of this work was to investigate the effect of three pretreatment techniques (thermal, alkaline, acidic) on the chemical composition and the methane yield of OFI biomass. A composite experimental design with three factors and two to three levels was implemented, and regression modelling was employed using a total of 10 biochemical methane potential (BMP) tests. The measured methane yields ranged from 289 to 604 NmL/gVS_added; according to the results, only the acidic pretreatment (HCl) was found to significantly increase methane generation. However, as the experimental values were quite high with regards to the theoretical methane yield of the substrate, this effect still needs to be confirmed via further research. The alkaline pretreatment (NaOH) did not noticeably affect methane yields (an average reduction of 8% was recorded), despite the fact that it did significantly reduce the lignin content. Thermal pretreatment had no effect on the methane yields or the chemical composition. Scanning electron microscopy images revealed changes in the chemical structure after the addition of NaOH and HCl. Modelling of the cumulated methane production by the Gompertz modified equation was successful and aided in understanding kinetic advantages linked to some of the pretreatments. For example, the alkaline treatment (at the 20% dosage) at room temperature resulted to a μ_max (maximum specific methane production rate [NmLCH₄/(gVS_added·d)]) equal to 36.3 against 18.6 for the control.

Nutrient contributions and biogas potential of co-digestion of feedstocks and dairy manure

This study focused on collection of data on nutrient flow and biogas yield at a commercial anaerobic digester managed with dairy manure from a 1000 cow dairy and co-digestion of additional feedstocks. Feedstocks included: blood, fish, paper pulp, out of date beverages and grease trap waste. Mass flow of inputs and outputs, nutrient concentration of inputs and outputs, and biogas yield were obtained. It was determined that manure was the primary source of nutrients to the anaerobic digester when co-digested with feedstocks. The percentage of contribution from manure to the total nutrient inputs for total nitrogen, ammonia-nitrogen, phosphorus and total solids was 46.3%, 67.7%, 32.8% and 23.4%, respectively. On average, manure contributed the greatest amount of total nitrogen and ammonia-nitrogen. Grease trap waste contributed the greatest amount of phosphorus and total solids at approximately 50%. Results demonstrated that a reliable estimate of nutrient inflow could be obtained from the product of the nutrient analyses of a single daily composite of influent subsamples times the total daily flow estimated with an in-line flow meter. This approach to estimate total daily nutrient inflow would be more cost effective than testing and summing the contribution of individual feedstocks. Data collected after liquid-solid separation confirmed that the majority (>75%) of nutrients remain with the liquid effluent portion of the manure stream. It was demonstrated that the ash concentration in solids before and after composting could be used to estimate the mass balance of total solids during the compost process. This data confirms that biogas or methane yield could be accurately measured from the ratio of % volatile solids to % total solids.

Characterisation of the biodegradability of post-treated digestates via the chemical accessibility and complexity of organic matter

The stability of digestate organic matter is a key parameter for its use in agriculture. Here, the organic matter stability was compared between 14 post-treated digestates and the relationship between organic matter complexity and biodegradability was highlighted. Respirometric activity and CH₄ yields in batch tests showed a positive linear correlation between both types of biodegradability (R²=0.8). The accessibility and complexity of organic matter were assessed using chemical extractions combined with fluorescence spectroscopy, and biodegradability was mostly anti-correlated with complexity of organic matter. Post-treatments presented a significant effect on the biodegradability and complexity of organic matter. Biodegradability was low for composted digestates which comprised slowly accessible complex molecules. Inversely, solid fractions obtained after phase separation contained a substantial part of remaining biodegradable organic matter with a significant easily accessible fraction comprising simpler molecules. Understanding the effect of post-treatment on the biodegradability of digestates should help to optimize their valorization.

Biochemical methane potential, biodegradability, alkali treatment and influence of chemical composition on methane yield of yard wastes

In this study, the biochemical CH4 potential, rate, biodegradability, NaOH treatment and the influence of chemical composition on CH4 yield of yard wastes generated from seven trees were examined. All the plant parts were sampled for their chemical composition and subjected to the biochemical CH4 potential assay. The component parts exhibited significant variation in biochemical CH4 potential, which was reflected in their ultimate CH4 yields that ranged from 109 to 382 ml g(-1) volatile solids added and their rate constants that ranged from 0.042 to 0.173 d(-1). The biodegradability of the yard wastes ranged from 0.26 to 0.86. Variation in the biochemical CH4 potential of the yard wastes could be attributed to variation in the chemical composition of the different fractions. In the Thespesia yellow withered leaf, Tamarindus fruit pericarp and Albizia pod husk, NaOH treatment enhanced the ultimate CH4 yields by 17%, 77% and 63%, respectively, and biodegradability by 15%, 77% and 61%, respectively, compared with the untreated samples. The effectiveness of NaOH treatment varied for different yard wastes, depending on the amounts of acid detergent fibre content. Gliricidia petals, Prosopis leaf, inflorescence and immature pod, Tamarindus seeds, Albizia seeds, Cassia seeds and Delonix seeds exhibited CH4 yields higher than 300 ml g(-1) volatile solids added. Multiple linear regression models for predicting the ultimate CH4 yield and biodegradability of yard wastes were designed from the results of this work.

Anaerobic digestion of tomato processing waste: Effect of alkaline pretreatment

The objective of the work was to assess the effect of mild alkaline pretreatment on the anaerobic biodegradability of tomato processing waste (TPW). Experiments were carried out in duplicate BMP bottles using a pretreatment contact time of 4 and 24 h and a 1% and 5% NaOH dosage. The cumulative methane production during a 30 d period was recorded and modelled. The alkaline pretreatment did not significantly affect methane production in any of the treatments in comparison to the control. The average methane production for all runs was 320 NmL/gVS. Based on first order kinetic modelling, the alkaline pretreatment was found to slow down the rate of methanogenesis, mainly in the two reactors with the highest NaOH dosage. The biodegradability of the substrates ranged from 0.75 to 0.82 and from 0.66 to 0.72 based on two different approaches.

The role of biological processes in reducing both odor impact and pathogen content during mesophilic anaerobic digestion

Mesophilic anaerobic digestion (MAD) produces renewable energy, but it also plays a role in reducing the impact of digestates, both by reducing odor and pathogen content. Ten full-scale biogas plants characterized by different plant designs (e.g. single digesters, parallel or serial digesters), plant powers (ranging from 180 to 999 kWe), hydraulic retention time (HRT) (ranging between 20 to 70 days) and feed mixes were monitored and odors and pathogens were observed in both ingestates and digestates. Results obtained indicated that MAD reduced odors (OU) from, on average, OUingestate=99,106±149,173 OU m(-2) h(-1) (n=15) to OU digestate=1106±771 OU m(-2) h(-1) (n=15). Pathogens were also reduced during MAD both because of ammonia production during the process and competition for substrate between pathogens and indigenous microflora, i.e. Enterobacteriaceae from 6.85∗10(3)±1.8∗10(1) to 1.82∗10(1)±3.82∗10(1); fecal Coliform from 1.82∗10(4)±9.09 to 2.45∗10(1)±3.8∗10(1); Escherichia coli from 8.72∗10(3)±2.4∗10(1) to 1.8∗10(1)±2.94∗10(1); Clostridium perfringens from 6.4∗10(4)±7.7 to 5.2∗10(3)±8.1 (all data are expressed as CFU g(-1) ww). Plants showed different abilities to reduce pathogen indicators, depending on the pH value and toxic ammonia content.

Comparison of different pretreatments for the production of bioethanol and biomethane from corn stover and switchgrass

In this study the efficiency of mild ionic liquid (IL) pretreatment and pressurized hot water (PHW) is evaluated and compared in terms of bioethanol and biomethane yields, with corn stover (CS) and switchgrass (SG) as model bioenergy crops. Both feedstocks pretreated with the IL 1-ethyl-3-methylimidazolium acetate [C2C1Im][OAc] at 100°C for 3h exhibited lower glucose yield that those treated with harsher pretreatment conditions previously used. Compared to PHW, IL pretreatment demonstrated higher bioethanol yields; moreover IL pretreatment enhanced biomethane production. Taking into consideration both bioethanol and biomethane productions, results indicated that when using IL pretreatment, the total energy produced per kg of total solids was higher compared to untreated biomasses. Specifically energy produced from CS and SG was +18.6% and +34.5% respectively, as compared to those obtained by hot water treatment, i.e. +2.3% and +23.4% for CS and SG, respectively.

Early prediction of Biochemical Methane Potential through statistical and kinetic modelling of initial gas production

A major drawback of Biochemical Methane Potential (BMP) tests is their long test duration, which could be reduced substantially if the final gas production could be predicted at an earlier stage. For this purpose, this study evaluates 61 different algorithms for their capability to predict the final BMP and required degradation time based on data from 138 BMP tests of various substrate types. By combining the best algorithms it was possible to predict the BMP with a relative root mean squared error (rRMSE) of less than 10% just 6days after initiation of the experiment. The results from this study indicate that there is a possibility to shorten the test length substantially by combining laboratory tests and intelligent prediction algorithms. Shorter test duration may widen the possible applications for BMP tests in full-scale biogas plants, allowing for a better selection and proper pricing of biomass.

Predicting the methane yield of lignocellulosic biomass in mesophilic solid-state anaerobic digestion based on feedstock characteristics and process parameters

In this study, multiple linear regression (MLR) and artificial neural network (ANN) models were explored and validated to predict the methane yield of lignocellulosic biomass in mesophilic solid-state anaerobic digestion (SS-AD) based on the feedstock characteristics and process parameters. Out of the eleven factors analyzed in this study, the inoculation size (F/E ratio), and the contents of lignin, cellulose, and extractives in the feedstock were found to be essential in accurately determining the 30-day cumulative methane yield. The interaction between F/E ratio and lignin content was also found to be significant. MLR and ANN models were calibrated and validated with different sets of data from literature, and both methods were able to satisfactorily predict methane yields of SS-AD, with the lowest standard error for prediction obtained by an ANN model. The models developed in this study can provide guidance for future feedstock evaluation and process optimization in SS-AD.

Production costs and operative margins in electric energy generation from biogas. Full-scale case studies in Italy

The purpose of this study was to observe the economic sustainability of three different biogas full scale plants, fed with different organic matrices: energy crops (EC), manure, agro-industrial (Plants B and C) and organic fraction of municipal solid waste (OFMSW) (Plant A). The plants were observed for one year and total annual biomass feeding, biomass composition and biomass cost (€ Mg(-1)), initial investment cost and plant electric power production were registered. The unit costs of biogas and electric energy (€ Sm(-3)biogas, € kWh(-1)EE) were differently distributed, depending on the type of feed and plant. Plant A showed high management/maintenance cost for OFMSW treatment (0.155 € Sm(-3)biogas, 45% of total cost), Plant B suffered high cost for EC supply (0.130 € Sm(-3)biogas, 49% of total cost) and Plant C showed higher impact on the total costs because of the depreciation charge (0.146 € Sm(-3)biogas, 41% of total costs). The breakeven point for the tariff of electric energy, calculated for the different cases, resulted in the range 120-170 € MWh(-1)EE, depending on fed materials and plant scale. EC had great impact on biomass supply costs and should be reduced, in favor of organic waste and residues; plant scale still heavily influences the production costs. The EU States should drive incentives in dependence of these factors, to further develop this still promising sector.

Programmed iron oxide nanoparticles disintegration in anaerobic digesters boosts biogas production

A novel concept of dosing iron ions using Fe3O4 engineered nanoparticles is used to improve biogas production in anaerobic digestion processes. Since small nanoparticles are unstable, they can be designed to provide ions in a controlled manner, and the highest ever reported improvement of biogas production is obtained. The nanoparticles evolution during operation is followed by an array of spectroscopic techniques.

Assessment of factors influencing the biomethane yield of maize silages

A large set of maize silage samples was produced to assess the major traits influencing the biomethane production of this crop. The biomass yield, the volatile solids contents and the biochemical methane potential (BMP) were measured to calculate the biomethane yield per hectare (average=7266m(3)ha(-1)). The most influential factor controlling the biomethane yield was the cropping environment. The biomass yield had more impact than the anaerobic digestibility. Nevertheless, the anaerobic digestibility of maize silages was negatively affected by high VS content in mature maize. Late maturing maize varieties produced high biomass yield with high digestibility resulting in high biomethane yield per hectare. The BMP was predicted with good accuracy using solely the VS content.

Biogas production from Pongamia biomass wastes and a model to estimate biodegradability from their composition

In this study, I investigated the chemical characteristics, biochemical methane potential, conversion kinetics and biodegradability of untreated and NaOH-treated Pongamia plant parts, and pod husk and press cake from the biodiesel industry to evaluate their suitability as an alternative feedstock for biogas production. The untreated Pongamia seeds exhibited the maximum CH4 yield of 473 ml g (-1) volatile solid (VS) added. Yellow, withered leaves gave a yield as low as 122 ml CH4 g (-1) VS added. There were significant variations in the CH4 production rate constants, which ranged from 0.02 to 0.15 d (-1), and biodegradability, which ranged from 0.25 to 0.98. NaOH treatment of leaf and pod husk, which were highly rich in fibers, increased the yields by 15-22% and CH4 production rate constants by 20-75%. Utilization of Pongamia wastes in biogas digesters not only influences the economics of biodiesel production but also yields CH4 fuel and protects the environment. The experimental data from this study were used to develop a multiple regression model, which could estimate biodegradability based on biochemical characteristics. The model predicted the biodegradability of previously published biomass wastes (r(2) = 0.88) from their biochemical composition. The theoretical CH4 yields estimated as 350 ml g(-1) chemical oxygen demand destroyed are much higher than the experimental yields as 100% biodegradability is assumed for each substrate. Upon correcting the theoretical CH4 yields with biodegradability data obtained from chemical analyses of substrates, their ultimate CH4 yields could be predicted rapidly.

Feasibility of grass co-digestion in an agricultural digester, influence on process parameters and residue composition

This study investigated the potential of co-digestion of grass clippings in a typical Flemish agro-digester characterized by an input of 30% manure, 30% maize silage and 40% side streams. No significant adverse effects in the microbiological functioning of the reactors were detected when part of the maize input was replaced by 10-20% grass. However at the highest dosage of grass input, dry matter content and the viscosity of the reactor content increased substantially. These parameters could be reduced again by enzyme addition in the form of MethaPlus L100. It can be concluded that co-digestion of 20% grass in an agricultural digester would not pose any problem if dry matter content and viscosity are improved by the use of an enzyme mixture.

Short mechanical biological treatment of municipal solid waste allows landfill impact reduction saving waste energy content

The aim of this work was to evaluate the effects of full scale MBT process (28 d) in removing inhibition condition for successive biogas (ABP) production in landfill and in reducing total waste impact. For this purpose the organic fraction of MSW was treated in a full-scale MBT plant and successively incubated vs. untreated waste, in simulated landfills for one year. Results showed that untreated landfilled-waste gave a total ABP reduction that was null. On the contrary MBT process reduced ABP of 44%, but successive incubation for one year in landfill gave a total ABP reduction of 86%. This ABP reduction corresponded to a MBT process of 22 weeks length, according to the predictive regression developed for ABP reduction vs. MBT-time. Therefore short MBT allowed reducing landfill impact, preserving energy content (ABP) to be produced successively by bioreactor technology since pre-treatment avoided process inhibition because of partial waste biostabilization.

Aerobic biological pretreatment of municipal solid waste with a high content of putrescibles: effect on landfill emissions

The objective of this work was to study the effect of aerobic biological pretreatment on the emissions of municipal solid waste (MSW) with a high content of putrescibles after landfilling. For this purpose, the organic fraction of MSW was simulated by a mixture of food waste and office paper at a 2.4:1 wet weight ratio. MSW was first pretreated aerobically for three different time periods (8, 45 and 90 days) resulting in organic matter reductions equal to 15%, 45% and 81% respectively. MSW were then placed in 160-L air-tight anaerobic bioreactors. The control anaerobic bioreactors contained untreated MSW. Anaerobic experiments lasted from 300 to 550 days. Results showed that the biogas production from untreated MSW was 372 NL dry kg(-1) (average of two replications) after 530 days. The MSW that was pretreated aerobically for 45 days and 90 days yielded 130 and 62 NL dry kg(-1) of biogas after 310 days and 230 days respectively. However, the 8-day (very short-term) pretreatment period led to an increase of the biogas yield (550 NL dry kg(-1) after 340 days) compared with that of raw refuse. All three runs with aerobically pretreated MSW reached the steady methanogenic phase faster than raw MSW. Leachate emissions were significantly lower in the aerobically-pretreated MSWthan the untreated ones. The leachate ammonium concentrations had an increasing trend in all anaerobic reactors and reached a plateau of between 2 and 3.5 g L(-1) at the end of the process.

Thermophilic anaerobic co-digestion of separated solids from acidified dairy cow manure

This study examined the potential for partly substituting dairy cow manure (DCM) with solids from solid to liquid separation of acidified dairy cow manure (SFDCM) during thermophilic anaerobic digestion. Three different substituting levels with a maximum of 30% substitution were tested. All digesters substituting DCM with SFDCM showed a stable biogas production with low volatile fatty acid concentrations after a short transition period. An increased methane yield in terms of digester volume compared to DCM alone was obtained with increasing amount of SFDCM and about 50% more methane was achieved when 30% of DCM was substituted with SFDCM. The digestates were subsequently digested in a post digestion, during which the methane yield increased proportionally with increasing amounts of SFDCM. It can be concluded that SFDCM is a suitable biomass for co-digestion and can be used to increase methane yield in terms of digester volume at ratios up to at least 30%.

Effect of cerium dioxide, titanium dioxide, silver, and gold nanoparticles on the activity of microbial communities intended in wastewater treatment

Growth in production and use of nanoparticles (NPs) will result increased concentrations of these in industrial and urban wastewaters and, consequently, in wastewater-treatment facilities. The effect of this increase on the performance of the wastewater-treatment process has not been studied systematically and including all the microbial communities involved in wastewater treatment. The present work investigates, by using respiration tests and biogas-production analysis, the inhibitory effect of four different commonly used metal oxide (CeO(2) and TiO(2)) and zero-valent metal (Ag and Au) nanoparticles on the activity of the most important microbial communities present in a modern wastewater-treatment plant. Specifically, the actions of ordinary heterotrophic organisms, ammonia oxidizing bacteria, and thermophilic and mesophilic anaerobic bacteria were tested in the presence and absence of the nanoparticles. In general, CeO(2) nanoparticles caused the greatest inhibition in biogas production (nearly 100%) and a strong inhibitory action of other biomasses; Ag nanoparticles caused an intermediate inhibition in biogas production (within 33-50%) and a slight inhibition in the action of other biomasses, and Au and TiO(2) nanoparticles caused only slight or no inhibition for all tested biomasses.

Anaerobic and aerobic transformations affecting stability of dewatered sludge during long-term storage in a lagoon

The goal of this work was to study long-term behavior of anaerobically digested and dewatered sludge (biosolids) in a lagoon under anaerobic and aerobic conditions to determine the stability of the final product as an indicator of its odor potential. Field lagoons were sampled to estimate spatial and temporal variations in the physical-chemical properties and biological stability characteristics such as volatile solids content, accumulated oxygen uptake, and soluble protein content and odorous compound assessment. The analyses of collected data suggest that the surface layer of the lagoon (depth of above 0.15 m) undergoes long-term aerobic oxidation resulting in a higher degree of stabilization in the final product. The subsurface layers (depth 0.15 m below the surface and deeper) are subjected to an anaerobic environment where the conditions favor the initial rapid organic matter degradation within approximately the first year, followed by slow degradation.

On-field study of anaerobic digestion full-scale plants (Part II): new approaches in monitoring and evaluating process efficiency

Biogas plants need easy and practical tools for monitoring and evaluating their biological process efficiency. As soon as, in many cases, biomass supply present considerable costs, full-scale anaerobic digestion (AD) processes must approach, as much as possible, the potential biogas yield of the organic mixture fed to the biodigesters. In this paper, a new indicator is proposed (the bio-methane yield, BMY), for measuring the efficiency in full-scale AD processes, based on a balance between the biochemical methane potential (BMP) of the input biomass and the residual BMP of the output materials (digestate). For this purpose, a one-year survey was performed on three different full-scale biogas plants, in the Italian agro-industrial context, and the bio-chemical processes were fully described in order to calculate their efficiencies (BMY = 87-93%) and to validate the new indicator proposed, as useful and easily applicable tool for full-scale AD plants operators.

Biogas production and saccharification of Salix pretreated at different steam explosion conditions

Different steam explosion conditions were applied to Salix chips and the effect of this pretreatment was evaluated by running both enzymatic hydrolysis and biogas tests. Total enzymatic release of glucose and xylose increased with pretreatment harshness, with maximum values being obtained after pretreatment for 10 min at 210°C. Harsher pretreatment conditions did not increase glucose release, led to degradation of xylose and to formation of furfurals. Samples pretreated at 220 and 230°C initially showed low production of biogas, probably because of inhibitors produced during the pretreatment, but the microbial community was able to adapt and showed high final biogas production. Interestingly, final biogas yields correlated well with sugar yields after enzymatic hydrolysis, suggesting that at least in some cases a 24h enzymatic assay may be developed as a quick method to predict the effects of pretreatment of lignocellulosic biomass on biogas yields.

On-field study of anaerobic digestion full-scale plants (part I): an on-field methodology to determine mass, carbon and nutrients balance

The mass balance (input/output mass flows) of full-scale anaerobic digestion (AD) processes should be known for a series of purposes, e.g. to understand carbon and nutrients balances, to evaluate the contribution of AD processes to elemental cycles, especially when digestates are applied to agricultural land and to measure the biodegradation yields and the process efficiency. In this paper, three alternative methods were studied, to determine the mass balance in full-scale processes, discussing their reliability and applicability. Through a 1-year survey on three full-scale AD plants and through 38 laboratory-scale batch digesters, the congruency of the considered methods was demonstrated and a linear equation was provided that allows calculating the wet weight losses (WL) from the methane produced (MP) by the plant (WL=41.949*MP+20.853, R(2)=0.950, p<0.01). Additionally, this new tool was used to calculate carbon, nitrogen, phosphorous and potassium balances of the three observed AD plants.

Parameter identification and modeling of the biochemical methane potential of waste activated sludge

Anaerobic digestion is widely used in waste activated sludge treatment. In this paper, partial least-squares (PLS) is employed to identify the parameters that are determining the biochemical methane potential (BMP) of waste activated sludge. Moreover, a model is developed for the prediction of the BMP. A strong positive correlation is observed between the BMP and volatile fatty acids and carbohydrate concentrations in the sludge. A somewhat weaker correlation with COD is also present. Soluble organics (sCOD, soluble carbohydrates and soluble proteins) were shown not to influence the BMP in the observed region. This finding could be most-valuable in the context of application of sludge pretreatment methods. The obtained model was able to satisfactory predict the BMP.

The methane yield of digestate: effect of organic loading rate, hydraulic retention time, and plant feeding

In biogas plants, huge volumes of digestate are produced daily and stored in uncovered tanks, which leak methane into the atmosphere and cause negative environmental impacts. To better understand the effect that different operating parameters of anaerobic digestion plants have on digestate residual methane yield, four digestate samples collected from plants with very different operations were analysed in batch reactors. Their methane yields were very heterogeneous and varied between 2.88 and 37.63 NL/kgVS. The methane yield was shown to be highly influenced by the A.D. plant Organic Loading Rate and by feedstock quality; hydraulic retention time had only limited effects.