Preparation of ferric-activated sludge-based adsorbent from biological sludge for tetracycline removal

Enhanced adsorption of tetracycline by lanthanum/iron co-modified rice shell biochar: Synthesis, adsorption performance, site energy distribution and regeneration

A novel La/Fe co-modified biochar derived from rice shell (La/Fe@RSBC) was prepared and employed in tetracycline (TC) adsorption from water. The characterizations, kinetics, isotherms, thermodynamics, and site energy distribution (SED) were studied to investigate TC adsorption behaviors. La/Fe@RSBC exhibited the maximum adsorption capacity towards TC of 414.84 mg/g, which was 1.27-2.41 folds than that of RSBC, La@RSBC, and Fe@RSBC. The possible adsorption mechanism of TC dominantly involved H bond, surface complexation, pore filling, electrostatic attraction, and π-π electron donor-acceptor (EDA) interaction. Moreover, TC adsorption behavior was spontaneous and endothermic, significantly related to the compositions and dosage of La/Fe@RSBC, initial pH, and solution temperature. Additionally, SED results promulgated that co-loaded Fe and La synergistically enhanced the affinity of biochar and provided more adsorption sites for TC at a higher temperature. The residual TC after regeneration by ethanol dominantly inhibited the third stage of adsorption, that is, the adsorption of TC on the inner surface of La/Fe@RSBC in next run. Importantly, H2O2 combined with La/Fe@RSBC-mediated advanced oxidation process could effectively clear residual TC after ethanol desorption, which obviously improved the service life of La/Fe@RSBC. In addition, the swine wastewater treatment demonstrated that La/Fe@RSBC had a promising potential application in practical application.

Enhanced Tetracycline Adsorption Using KOH-Modified Biochar Derived from Waste Activated Sludge in Aqueous Solutions

Antibiotic pollution poses a serious environmental concern worldwide, posing risks to ecosystems and human well-being. Transforming waste activated sludge into adsorbents for antibiotic removal aligns with the concept of utilizing waste to treat waste. However, the adsorption efficiency of these adsorbents is currently limited. This study identified KOH modification as the most effective method for enhancing tetracycline (TC) adsorption by sludge biochar through a comparative analysis of acid, alkali, and oxidant modifications. The adsorption characteristics of TC upon unmodified sludge biochar (BC) as well as KOH-modified sludge biochar (BC-KOH) were investigated in terms of equilibrium, kinetics, and thermodynamics. BC-KOH exhibited higher porosity, greater specific surface area, and increased abundance of oxygen-based functional groups compared to BC. The TC adsorption on BC-KOH conformed the Elovich and Langmuir models, with a maximum adsorption capacity of 243.3 mg/g at 298 K. The adsorption mechanisms included ion exchange, hydrogen bonding, pore filling, and electrostatic adsorption, as well as π-π interactions. Interference with TC adsorption on BC-KOH was observed with HCO3-, PO43-, Ca2+, and Mg2+, whereas Cl-, NO3-, and SO42- ions exhibited minimal impact on the adsorption process. Following three cycles of utilization, there was a slight 5.94% reduction in the equilibrium adsorption capacity, yet the adsorption capacity remained 4.5 times greater than that of unmodified sludge BC, underscoring its significant potential for practical applications. This research provided new insights to the production and application of sludge biochar for treating antibiotic-contaminated wastewater.

Evaluation and optimization of six adsorbents for removal of tetracycline from swine wastewater: Experiments and response surface analysis

The removal of tetracycline antibiotics using adsorbents is becoming an environmentally friendly and cost-effective method. This study systematically analyzed the stability, structure, morphology, and chemical properties of various adsorbents. Batch adsorption experiments (pH, time, temperature, tetracycline concentration, and adsorbent dosage) were conducted to compare the adsorption capacity of the six adsorbents (biochar, activated carbon, montmorillonite, zeolite, chitosan, and polymerized aluminum chloride) for tetracycline removal. The results indicated that montmorillonite had the highest adsorption efficiency, followed by biochar, with chitosan showing the lowest efficiency. At an adsorbent dose of 25 g/L and an initial tetracycline concentration of 120 mg/L, the removal rates of tetracycline by montmorillonite, biochar, and chitosan were 97.6%, 69.3%, and 12.2%, respectively. Furthermore, the removal rate of tetracycline by biochar, following the response surface methodology optimal mode, increased by 5.5%. The Elovich model was better suited to explain the adsorption process of tetracycline compared to the conventional pseudo-first kinetic model and second-order kinetic model. The isothermal adsorption model suggested that both chemisorption and physisorption occurred in all removal processes, in which chemisorption dominated. Tetracycline was efficiently adsorbed through the combined effects of pore filling, electrostatic attraction, π-π interactions, and complexation reactions of surface functional groups. Additionally, montmorillonite demonstrated superior performance as an adsorbent for tetracycline removal from swine wastewater compared to the other adsorbents studied.

Key role of Phyllanthus emblica L. fruit extract promotes ZVI/H2O2 process: rich titratable acid, suitable chelating ability, and antioxidant capacity

Phyllanthus emblica L. fruit extract (PFE) was introduced to improve ZVI/H2O2 technology, and the efficiency and mechanism of PFE promoting ZVI/H2O2 technology were explored. With the introduction of PFE, the Norfloxacin (NOR) removal rate and kobs of the process were improved by 41.17% and 5.08 times, respectively. In the ZVI/H2O2/PFE process, the degradation of NOR by the attack of ROS is the main pathway for decontamination and is dominated by the heterogeneous reaction on the catalyst surface. PFE contains 13.92 g/L titratable acid and has good complexing ability and antioxidant ability. The mechanism of PFE promoting ZVI/H2O2 technology was based on lowering the pH, complemented by chelation and antioxidant capacity. With the introduction of PFE, the utilization rate of the reagent was significantly increased (7.56 times for ZVI and 3.21 times for H2O2), the applicable pH range was widened (6-9) and the iron sludge was reduced (32.80%). Meanwhile, the concept of UPR is proposed for the first time. The result is the key role to the selection of green promoters in the ZVI/H2O2 process depends on the abundance of titratable acid, followed by a certain chelating ability and antioxidant capacity.

Low-cost eggshell-fly ash adsorbent for phosphate recovery: A potential slow-release phosphate fertilizer

Fly ash (FA) and eggshells (ES) are common solid wastes with significant potential for the recovery of phosphorus from water. This study focuses on synthesizing a low-cost and environmental-friendly phosphate adsorbent called eggshell-fly ash geopolymer composite (EFG) using eggshells instead of chemicals. The CaO obtained from the high-temperature pyrolysis of eggshells provides active sites for phosphate adsorption, and CO2 serves as a pore-forming agent. The phosphate adsorption performance of EFG varied with the eggshell-fly ash ratios and achieved a maximum of 49.92 mg P/g at an eggshell-fly ash ratio of 40 %. The adsorption process was well described by the pseudo-second-order model and the Langmuir model. EFG also exhibited a good regeneration performance through six-cycle experiments and achieved the highest phosphate desorption at pH 4.0. The results of the column experiment showed that EFG can be used as a filter media for phosphorus removal in a real-scale application with low cost. Soil burial test indicated saturated EFG has a good phosphate slow-release performance (maintained for up to 60 days). Overall, EFG has demonstrated to be a promising adsorbent for phosphorus recovery.

Tetracycline (TC) removal from wastewater with activated carbon (AC) obtained from waste grape marc: activated carbon characterization and adsorption mechanism

In this study, activated carbons were obtained from grape marc for tetracycline removal from wastewater. Activated carbons were obtained by subjecting them to pyrolysis at 300, 500, and 700 °C, respectively, and the effect of pyrolysis temperature on activated carbons was investigated. The physicochemical and surface properties of the activated carbons were evaluated by SEM, FTIR, XRD, elemental analysis, N2 adsorption/desorption isothermal, thermal gravimetric (TG) and derivative thermogravimetric (DTG), and BET surface area analysis. When the BET surface areas were examined, it was found that 4.25 m2/g for activated carbon was produced at 300 °C, 44.23 m2/g for activated carbon obtained at 500 °C and 44.23 m2/g at 700 °C, which showed that the BET surface areas increased with increasing pyrolysis temperatures. The pore volumes of the synthesized activated carbons were 0.0037 cm3/g, 0.023 cm3/g, and 0.305 cm3/g for pyrolysis temperatures of 300, 500, and 700 °C, respectively, while the average pore size was found to be 8.02 nm, 9.45 nm, and 10.29 nm, respectively. A better adsorption capacity was observed due to the decrease in oxygen-rich functional groups with increasing pyrolysis temperature. It was observed that the activated carbon obtained from grape skins can easily treat hazardous wastewater containing tetracycline due to its high carbon content and surface functional groups. It was also shown that the activated carbon synthesized in this study has a higher pore volume despite its low surface area compared to the studies in the literature. Thanks to the high pore volume and surface active groups, a successful tetracycline removal was achieved.

Adsorption Characteristics of Ball Milling-Modified Chinese Medicine Residue Biochar Toward Quercetin

Using traditional Chinese medicine residues as raw materials, different biochars (BC) were prepared through oxygen-limited pyrolysis at 300 °C, 500 °C, and 700 °C, and BC was ball-milled to produce ball-milled biochar (BMC). Using these adsorbents to adsorb the allelopathic autotoxic substance quercetin. The physical and chemical properties of various biochars derived from traditional Chinese medicine residues were characterized using the Brunauer-Emmett-Teller-N2 surface areas (BET), scanning electron microscopy (SEM), Fourier transform IR spectroscopy (FTIR), X-ray diffraction (XRD), and Raman spectroscopy (Raman). The study investigated the effects of the initial pH value, different humic acid concentrations, and multiple adsorption-desorption experiments on the removal of quercetin from the solution. The article discusses the adsorption mechanism of quercetin in solution by biochar from a traditional Chinese medicine residue, based on the results of adsorption kinetics and adsorption isotherm fitting. The findings indicate that increasing the pyrolysis temperature reduces the oxygen-containing functional groups of BC, enhances the aromaticity, and stabilizes the carbon structure. The pore structure of BMC becomes more complex after ball milling, which increases the number of oxygen-containing functional groups on the surface. Among the samples tested, BMC700 exhibits the best adsorption performance, with an adsorption capacity of 293.3 mg·g-1 at 318 K. The adsorption process of quercetin by BMC700 follows the pseudo-second-order kinetic model and the Freundlich adsorption isotherm model. The process is primarily a form of multimolecular layer adsorption. Its mechanism involves the pore-filling effect, hydrogen-bonding interaction, electrostatic interaction, and π-π coexistence, as well as the yoke effect. Additionally, they are highly recyclable and show promise in addressing continuous cropping issues.

Effective degradation of tetracycline and real pharmaceutical wastewater using novel nanocomposites of biosynthesized ZnO and carbonized toner powder

In this study, novel nanohybrids of biosynthesized zinc oxide (ZnO) and magnetite-nanocarbon (Fe3O4-NC) obtained from the carbonization of toner powder waste were fabricated and investigated for persulfate (PS) activation for the efficient degradation of tetracycline (TCN). The chemical and physical properties of the synthesized catalysts were analyzed using advanced techniques. ZnO/Fe3O4-NC nanohybrid with mass ratio 1:2, respectively in the presence of PS showed the highest TCN removal efficiency compared to the individual components (ZnO and Fe3O4-NC) and other nanohybrids with mass ratios of 1:1 and 2:1. The results indicated that efficient degradation of TCN could be attained at pH 3-7. The optimum operating parameters were TCN concentration of 12.8 mg/L, PS concentration of 7 Mm, and catalyst dose of 0.55 g/L. The high stability of ZnO/Fe3O4-NC (1:2) nanocomposite was assured by the slight drop in TCN degradation percentage from 97.27% to 85.45% after five successive runs under the optimum conditions and the concentrations of leached iron and zinc into the solution were monitored. The quenching experiments explored that the prevailing reactive entities were sulfate radicals. Additionally, the degradation of TCN in various water matrices was investigated, and a degradation pathway was suggested. Further, degradation of real pharmaceutical waste was conducted showing that the removal efficiencies of TCN, total organic carbon (TOC), and chemical oxygen demand (COD) were 89.79, 80.65, and 78.64% after 2 h under the optimum conditions. The effectiveness of the proposed system (ZnO/Fe3O4-NC (1:2) @ PS) for the degradation of real samples compiled from industrial effluents as well as its inexpensiveness and green nature qualify this system for the full-scale application.

Magnetic biochar enhanced copper immobilization in agricultural lands: Insights from adsorption precipitation and redox

Biochar has exceeded expectations for heavy metal immobilization and has been prepared from widely available sources and inexpensive materials. In this research, coconut shell biochar (CSB), bamboo biochar (BC), magnetic coconut shell charcoal (MCSB), and magnetic bamboo biochar (MBC) were manufactured via co-pyrolysis, and their adsorption properties were tested. The pseudo-secondary (R2 = 0.980-0.985) adsorption kinetic fittings for the four biochas were superior to the pseudo-primary kinetics (R2 = 0.969-0.982). Unmodified biochar adsorption isotherms were more consistent with the Freundlich model, while magnetic biochar fitted Langmuir models better. The maximum adsorption capacity of MCSB for Cu(Ⅱ) reached 371.50 mg g-1. The adsorption mechanisms quantitatively analysis of the biochar indicated that chemical precipitation and ion exchange contributed to the adsorption, in which the magnetic biochar metal-π complexation also enhanced the adsorption. The pot experiment revealed that MCSB (2.0 %DW) significantly enhanced the biomass of lettuce, and facilitated the immobilization of DTPA-Cu (p < 0.05). SEM-EDS, XPS, and FTIR were utilized for morphological characterization and functional group identification, and the increased active adsorption sites (-OH, -COOH, CO, and Fe-O) of MCSB enhanced chemisorption and π-π EDA complexation with Cu(Ⅱ). EEM-PARAFAC and RDA analysis further elucidated that magnetic biochar immobilized copper and reduced biotoxicity (efficiency: 76.12%) by adjusting soil pH, phosphate, and SOM release (negative correlation). The presence of iron oxides (FeOx) promoted in situ adsorption of metallic copper and offered new insights into soil remediation.

Thiamethoxam adsorption by ZnCl2 modified cow manure biochar: Mechanism and quantitative prediction

The overuse of thiamethoxam (THM) has threatened the survival of living organisms and it is necessary to find an environmentally friendly material to remove THM frequently detected in water. Biochar prepared from cow manure modified with ZnCl2 (Zn-CBC) was used to remove THM. Compared to the unmodified cow manure biochar (CBC), the removal ratio of THM by Zn-CBC was enhanced 35 times. In the mechanistic analysis, SEM and BET showed that Zn-CBC had a good pore structure and its specific surface area (166.502 m2 g-1) increased to 17 times that of CBC, indicating that Zn-CBC had good pore adsorption properties. The adsorption kinetic and isotherm implied that the main mechanism was chemisorption including π-π interaction and H-bonding. Furthermore, the stable graphitized structure of Zn-CBC allowed for efficient adsorption and reusability. In addition, this study constructed an intelligent prediction model using batch experiment data, and the high R2 (0.978) and low RMSE (0.057) implied that the model could accurately and quantitatively predict the adsorption efficiency. This paper provides a novel perspective to simultaneously remove the neonicotinoid insecticides and realize the resource utilization of cow manure.

Biochar for soil remediation: A comprehensive review of current research on pollutant removal

Biochar usage in soil remediation has turned out to be an enticing topic recently. Biochar, a product formed by pyrolysis of organic waste, which is rich in carbon, has the aptitude to ameliorate climate change by sequestering carbon while also enhancing soil quality and crop yields. Two-edged implications of biochar on soil amendment are still being discussed yet, clarity on the long-term implications of biochar on soil health and the environment is not yet achieved. As a result, it is crucial to systematically uncover the pertinent information regarding biochar remediation, as this can serve as a roadmap for future research on using biochar to remediate contaminated soils in mining regions. This review endeavors to bring forth run thoroughly the latest state of research on the use of biochar in soil remediation, along with its potential benefits, limitations, challenges, and future scope. By synthesizing existing literature on biochar soil remediation, this review aims to provide insights into the potential of biochar as a sustainable solution for soil remediation. Specifically, this review will highlight the key factors that influence the effectiveness of biochar for soil remediation and the potential risks associated with its use, as well as the current gaps in knowledge and future research directions.

Sustainable phosphorus adsorption and recovery from aqueous solution by a novel recyclable Ca-PAC-CTS

Phosphorus removal has been explored for a long time, however sustainable phosphorus adsorption and recovery with adsorbents recycling is rarely reported. This work proposes a sustainable phosphorus recycling route with calcium-modified powdered activated carbon with chitosan (Ca-PAC-CTS). The morphology, functional groups and crystal structure of Ca-PAC-CTS were characterized. The maximum phosphorus adsorption capacity was 16.73 mg/g Ca-PAC-CTS with Langmuir model at 298 K. Stable phosphorus sorption on Ca-PAC-CTS could be observed at the large range of pH (4- 10) when coexisting with NO3-, SO42-, Cl- and F-, except HCO3-. 98.95 % The recovery of adsorbed phosphorus could get to 98.95 % using 0.05 M sulfuric acid solution, and the phosphate adsorption efficiency through Ca-PAC-CTS remained to be more than 80 % after five adsorption-desorption cycles, suggesting that Ca-PAC-CTS was one of the promising adsorbents for sustainable removal and recovery of phosphorus in aqueous solution.

Characterization and application of Fe-modified biochar alleviating Cr(VI) stress in pak choi seedling cultivated in Cr-polluted hydroponics

Chromium (Cr) is one of the common environmental pollutants, which causes severe health hazards on human health and environmental security. In this study, we characterized two biochars, a raw biochar (RBC) and a Fe-modified biochar (MBC) made from poplar wood chips and determined the effect of the two biochars on remediation of hexavalent chromium (Cr(VI)) in hydroponic system by monitoring Pak choi growth. Results showed the surface area, pore number and pore volume were significantly higher in MBC than in PBC, but the pore size was larger in PBC than in MBC. When compared to the control, low concentrations of Cr(VI) (≤2 mg L-1) promoted the growth and biomass production of Pak choi by 10-78%. In contrast, the high concentrations of Cr(VI) (≥4 mg L-1) showed a significantly reduction of the growth and biomass production of Pak choi by 10-28%. Fe-modified biochar (MBC) had a more significant impact than RBC on the remediation of Cr in the Cr(VI) pollution and improved growth and biomass production of Pak choi to a greater extent. Our study indicated that MBC has a better effect on degrading Cr(VI) pollution. The findings provide scientific basis and reference for the remediation of heavy metals in aquatic ecosystems by using biochar.

Synthesis of co-pyrolyzed biochar using red mud and peanut shell for removing phosphate from pickling wastewater: Performance and mechanism

Iron (Fe)/iron oxide-modified biochar has practicable adsorption capability for phosphorus (P), but it is expensive. In this study, we synthesized novel low-cost and eco-friendly adsorbents co-pyrolyzed biochars using Fe-rich red mud (RM) and peanut shell (PS) wastes via a one-step pyrolysis process for removing P from pickling wastewater. The preparation conditions (heating rate, pyrolysis temperature, and feedstock ratio) and P adsorption behaviors were systematically investigated. In addition, a series of characterization and approximate site energy distribution (ASED) analyses were conducted to understand the P adsorption mechanisms. The magnetic biochar (BR7P3) with m (RM):m (PS) of 7:3 prepared at 900°C and 10 °C/min had a high surface area (164.43 m2/g) and different abundant ions (including Fe3+, and Al3+). In addition, BR7P3 exhibited the best P removal capability (142.6 mg/g). The Fe2O3 from RM was successfully reduced to Fe0, which was easily oxidized as Fe3+ to precipitate with H2PO4-. The electrostatic effect, Fe-O-P bonding, and surface precipitation were the main mechanisms of P removal. ASED analyses revealed that high distribution frequency and solution temperature led to a high P adsorption rate of the adsorbent. Therefore, this study provides new insight into the waste-to-wealth strategy by transforming PS and RM into mineral-biomass biochar with excellent P adsorption capability and environmental adaptability.

Super facile one-step synthesis of sugarcane bagasse derived N-doped porous biochar for adsorption of ciprofloxacin

A new N-doped biochar derived from sugarcane bagasse (NSB) was prepared by one-pot pyrolysis with sugarcane bagasse as feedstock, melamine as nitrogen source and NaHCO₃ as pore-forming agent, and then NSB was used to adsorb ciprofloxacin (CIP) in water. The optimal preparation conditions of NSB were determined based on the evaluation index of adsorbability of NSB for CIP. SEM, EDS, XRD, FTIR, XPS and BET characterizations were used to analyze the physicochemical properties of the synthetic NSB. It was found that the prepared NSB had excellent pore structure, high specific surface area and more nitrogenous functional groups. Meanwhile, it was demonstrated that the synergistic interaction between melamine and NaHCO₃ increased the pores of NSB and the largest surface area of NSB was 1712.19 m²/g. The CIP adsorption capacity of 212 mg/g was obtained under optimal parameters as follows: NSB amount 0.125 g/L, initial pH 6.58, adsorption temperature 30 °C, CIP initial concentration 30 mg/L and adsorption time 1 h. The isotherm and kinetics studies elucidated that the adsorption of CIP conformed both D-R model and Pseudo-second-order kinetic model. The high CIP adsorption capacity of NSB for CIP was due to the combined filling pore, π-π conjugation and hydrogen bonding. All results demonstrated that adsorption of CIP by the low-cost N-doped biochar of NSB is a reliable technology for the disposal of CIP wastewater.

Mesoporous Activated Biochar from Crab Shell with Enhanced Adsorption Performance for Tetracycline

In this study, three mesoporous-activated crab shell biochars were prepared by carbonation and chemical activation with KOH (K-CSB), H₃PO₄ (P-CSB), and KMnO₄ (M-CSB) to evaluate their tetracycline (TC) adsorption capacities. Characterization by SEM and a porosity analysis revealed that the K-CSB, P-CSB, and M-CSB possessed a puffy, mesoporous structure, with K-CSB exhibiting a larger specific surface area (1738 m²/g). FT-IR analysis revealed that abundant, surface ox-containing functional groups possessed by K-CSB, P-CSB, and M-CSB, such as -OH, C-O, and C=O, enhanced adsorption for TC, thereby enhancing their adsorption efficiency for TC. The maximum TC adsorption capacities of the K-CSB, P-CSB, and M-CSB were 380.92, 331.53, and 281.38 mg/g, respectively. The adsorption isotherms and kinetics data of the three TC adsorbents fit the Langmuir and pseudo-second-order model. The adsorption mechanism involved aperture filling, hydrogen bonding, electrostatic action, π-π EDA action, and complexation. As a low-cost and highly effective adsorbent for antibiotic wastewater treatment, activated crab shell biochar has enormous application potential.

In situ fabrication of a novel CdS/ZnIn2S4/g-C3N4 ternary heterojunction with enhanced visible-light photocatalytic performance

In this study, a novel g-C3N4-based ternary heterojunction was rationally designed and constructed by the in situ growth of ZnIn2S4 nanosheets and CdS nanoparticles onto the g-C3N4 nanosheets using a facile two-step oil-bath method. Through optimizing the proportion of ZnIn2S4 and CdS component, g-C3N4 nanosheets coupled with ZnIn2S4 nanosheets and CdS nanoparticles (denoted as CdS/ZnIn2S4/g-C3N4) exhibited obviously higher photocatalytic properties for RhB removal than the single-component and dual-component systems. Among the as-obtained ternary photocatalysts, it was found that the ternary CdS/ZnIn2S4/g-C3N4-0.2 photocatalyst displayed the optimum photocatalytic property (96%) within a short time (30 min), which was almost 27.42 and 1.17 times higher than that of pure g-C3N4 and binary ZnIn2S4/g-C3N4-0.7 composite. The excellent activity of the ternary CdS/ZnIn2S4/g-C3N4 heterostructure is assigned to the synergetic effects of CdS nanoparticles, ZnIn2S4 nanosheets and g-C3N4 nanosheets, which not only broaden the visible-light absorption range, but also improve the charge mobility and separation rate, thus boosting the visible-light-driven photocatalytic property of g-C3N4.

Enhanced adsorption of tetracycline using modified second pyrolysis oil-based drill cutting ash

In this work, second pyrolysis oil-based drill cutting ash (OBDCA-sp) was modified using NaOH and cetyltrimethylammonium bromide (CTAB), respectively. The modified OBDCA-sp was used as the novel adsorbent for adsorption of tetracycline (TC) in aqueous solutions. The original and modified OBDCA-sp were characterized by SEM, XRD, FTIR, zeta potential analysis, contact angle, and BET. The maximum theoretical adsorption quantity (45 ℃) for TC was calculated as 1.7 mg/g using CTAB-OBDCA-sp as the adsorbent. The adsorption isotherm of TC on OBDCA-sp was fitted well with Freundlich model and the adsorption kinetic was illustrated by pseudo-second-order model. Neutral condition was favorable for the adsorption of TC. The result of regeneration experiment indicated the reusability of OBDCA-sp. The hydrogen bonding was the possible mechanism for TC adsorption. This paper developed the novel surface modification methods of OBDCA-sp and provided an approach for the resource utilization of OBDCA-sp as an environmental functional material.

Efficient adsorption of tetracycline in aquatic system by thermally-treated sediment

The disposal of dredged sediment is a considerable challenge for environmental protection and resource utilization. In this study, the dredged sediment was thermally-treated to prepare as adsorbent and utilized for tetracycline adsorption. Sediments based adsorbents under different pyrolysis temperature and atmosphere (N₂ and limited oxygen) were obtained and 600 °C and N₂ atmosphere (600AN) exhibited maximum TC adsorption capacity (15.45 mg/g). SEM, N₂ adsorption-desorption isotherm, XRD, FTIR and XPS analysis suggested larger pore volume, relatively higher surface area, effective pore size distribution and abundant surface functional groups were the main reasons. Moreover, the influence of key adsorption parameters, including adsorbent dosage, initial pH, coexisting ions, ionic strength, contact time, initial TC concentration and ambient temperature had also been investigated. Results revealed that TC adsorption by 600AN were more consistent with pseudo-second order kinetic and Freundlich isothermal models. Combined with characterization results, which reasonably inferred that the adsorption mechanisms of 600AN were mainly involved pore-filling effect, hydrogen bonding interaction and π-π EDA interaction. This work has provided a low-cost, high efficiency and promising method for the dredged sediment reduction and resource recovery.

Biomass ash pyrolyzed from municipal sludge and its adsorption performance toward tetracycline: effect of pyrolysis temperature and KOH activation

Large amount of municipal sludge is difficult to handle; its resource utilization is an effective measure. In this study, the municipal sludge from sewage treatment plant was pyrolyzed without gas protection at different temperatures and potassium hydroxide (KOH) concentrations for activation. The pyrolysis products, named biomass ash, with higher surface area and enriched pore structures could be obtained at the pyrolysis temperature of 773 K. Moreover, the KOH activation for raw municipal sludge could further increase the surface area of the pyrolysis biomass ash. The maximum specific surface area was 44.71 m2/g, which was obtained under 2 mol/L KOH activation before pyrolysis at 773 K. And in this situation, the obtained pyrolysis biomass ash as adsorbent showed the maximum adsorption capacity of 50.75 mg/g toward tetracycline (TC). Moreover, the TC adsorption onto pyrolysis biomass ash obtained under various conditions followed the pseudo-second-order kinetic model. Adsorption thermodynamics analysis suggested the TC adsorption onto the pyrolysis biomass ash with no pre-activation was mainly due to the multi-molecule heterogeneous adsorption, while the TC adsorption onto pyrolysis biomass ash pretreated through the activation of KOH followed the monomer adsorption mechanism. This different adsorption mechanism was largely related to the pore structure, polarity, and aromaticity of the adsorbent.

FeCl3-activated biochar catalyst for heterogeneous Fenton oxidation of antibiotic sulfamethoxazole in water

One-step FeCl₃-mediated pyrolysis/activation was developed for preparation of bermudagrass (BG)-derived FeCl₃-activated biochars (FA-BCs) from bermudagrass (BG) as a heterogenous Fenton catalyst for heterogeneous Fenton oxidation of sulfamethoxazole (SMX) in water. The FA-BC prepared at the FeCl₃ to BG mass ratio of 2 (FA-BC) exhibited higher adsorption and Fenton oxidation of SMX than other mass ratios of the FeCl₃ to BG. FA-BC presented the great surface area (835 m²/g) and high SMX adsorption capacity (195 mg SMX/g BC), which was higher than various BCs in the previous studies. Additionally, the surface of FA-BC was attached with Fe₂O₃, Fe⁰, and Fe₃O₄ after the FeCl₃ activation. Under the optimal conditions for Fenton reaction (SMX concentration, 100 mg/L; loading of FA-BC, 0.1 g/L; dose of H₂O₂, 200 mg/L; temperature, 20 °C; pH 3; reaction time, 12 h), SMX and COD removal efficiencies reached 99.94% and 65.19%, respectively. Increasing reaction temperature from 20 to 50 °C significantly improved the SMX oxidation rate from 0.46 to 1.04 h^-1. The HO· radicals were proved to play a major role during the Fenton oxidation of SMX. In addition, the SMX solution treated by Fenton oxidation showed much less toxicity than the initial SMX solution. Additionally, the reusability tests of FA-BC indicated that 89.58% removal efficiency for SMX was still achieved after 3 cycles of Fenton oxidation under the optimal conditions. Furthermore, FA-BC can also efficiently remove SMX from the dairy wastewater. Therefore, FA-BC showed a high potential to eliminate aqueous SMX through adsorption and heterogeneous Fenton oxidation.

A critical review on utilization of sewage sludge as environmental functional materials

Sewage sludge (SS) is increasingly used as an environment functional material to reduce or control pollution and improve plant growth because of the large amounts of carbon and essential plant nutrients in it. To achieve the best application results, it is essential to comprehensively review recent progress in SS utilization. This review aims to fill the gaps in knowledge by describing the properties of SS, and its usage as adsorbents, catalysts and fertilizers, and certain application mechanisms. Although SS generates several benefits for the environment and humans, many challenges still exist to limit the application, including the risks posed by potentially toxic substances (e.g., heavy metals) in SS. Therefore, future research directions are discussed and how to make SS applications more feasible in terms of technology and economy.

Adsorption performance of tetracycline by the biomass ash derived from the pyrolysis of FeCl3-activated municipal sludge without gas protection

The municipal sludge activated by FeCl3 solution was pyrolyzed at 500 °C without gas protection, and the pyrolysis products, named as biomass ash, could effectively adsorb tetracycline (TC) from aqueous solution. Different FeCl3 concentrations could directly affect the physicochemical properties of the biomass ash, so that the biomass ash as adsorbent showed different adsorption efficiency toward TC. The activation of FeCl3 increased the oxygen-containing functional groups and surface polarities of the biomass ash. When the concentration of FeCl3 solution was 0.5 mol/L, the biomass ash behaved the maximum specific surface area (37.74 m2/g) and the best adsorption efficiency. The pseudo-second-order kinetics model and the Freundlich multi-molecule model could fully explain the TC adsorption process by the biomass ash pyrolyzed from municipal sludge activated by FeCl3. Moreover, the adsorption mechanism was mainly attributed to the chemical adsorption.

Production and characterization of cost-effective magnetic pine bark biochar and its application to remove tetracycline from water

Low-cost adsorbent, pine bark biochar (PBB) from the forest residue, was produced and applied to remove tetracycline (TC) from aqueous solution via adsorption pathway. The PBB, hence obtained, was modified using aqueous ferric and ferrous ion solutions to obtain magnetic pine bark biochar (M-PBB). Batch adsorption experiments were conducted to examine the adsorption of TC by PBB and M-PBB in the variation of pH, contact time, dosage, and temperature. The adsorbents were characterized by SEM/EDX, TGA, and pH_pzc. The adsorption mechanism was evaluated by fitting Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich (D-R) isotherms model. Also, the experimental data were analyzed by kinetics models (pseudo-first-order, pseudo-second-order, intra-particle diffusion, and Elovich) and thermodynamics. The maximum adsorption capacity (q_m) of M-PBB was 15.3 mg/g from the experiment at pH 6. A high correlation coefficient (R² ≈ 0.9) of Freundlich isotherm postulated multi-layer adsorption of TC on M-PBB at pH 6. The kinetic studies showed that the pseudo-first-order was more suitable for representing the adsorption of TC molecules on the surface. The thermodynamic analysis was showed that the adsorption process is favorable, spontaneous, and endothermic at studied temperatures. M-PBB demonstrated a potential for removal of TC from water as a low-cost and convenient adsorbent.

Enhanced adsorption performance of sulfamethoxazole and tetracycline in aqueous solutions by MgFe2O4-magnetic biochar

Biochar has been reported as an excellent adsorbent for antibiotics, but the application faces the challenges of complicated separation. Here, MgFe₂O₄-magnetic biochars (MBCs) derived from corncob were synthesized at 300 °C to remove sulfamethoxazole (SMX) and tetracycline (TC) simultaneously. The characteristics of MBC300 had a high magnetic intensity. MBC300 had the maximum adsorption capacity of SMX with 50.75 mg/g and the high adsorption amount of TC with 120.36 mg/g respectively, which were 4.49 and 6.48 times those of BC300. MBC300 had the advantage of energy conservation compared with MBC450 and MBC600. The better fitting kinetics and isotherms indicated that the SMX and TC sorption onto MBC300 were governed by chemisorption. FTIR and XPS analyses confirmed that the SMX sorption onto MBC300 was dominated by polar interactions and π-π electron donor-acceptor interactions (π-π EDA). Furthermore, the TC sorption was involved in pore filling, π-π EDA, H-bonds, and surface complexation. MBC300 presented effective adsorption of SMX and TC over a wide range of pH. The competition between antibiotics and coexisting pollutants of dissolved organic matter (DOM), Ca²⁺, CO₃^2-, and PO₄^3- significantly inhibited the sorption. The results indicate that MBC300 is an effective and promising adsorbent to treat SMX and TC simultaneously.

Ball milling sulfur-doped nano zero-valent iron @biochar composite for the efficient removal of phosphorus from water: Performance and mechanisms

This study successfully prepared a novel sulfur-doped nano zero-valent iron @biochar (BM-SnZVI@BC) by modifying corn stover biochar with Fe⁰ and S⁰ using a mechanical ball milling method for effective phosphorus (P) adsorption in the waterbody. Batch experiments revealed that BM-SnZVI@BC (BC/S⁰/Fe⁰ = 3:1:1) reached a Q_max of 25.00 mg P/g and followed PFO and Langmuir models. This work had shown that electrostatic attraction, surface chemical precipitation, hydrogen bonding, and ligand effects all contributed to P removal. Since the FeS layer mitigated the oxidation-induced surface passivation of nZVI, sulfidation significantly extended the lifetime of BM-SnZVI@BC, removing 84.4% of P even after 60 d aging in air. The regeneration experiments of composites showed that re-ball milling destroyed the surface iron oxide layer to improve the properties of the recovered material. This is an essential step in the design of P-removal agents to implement anti-aging and commercialization of adsorbents for engineering applications.

Tetracycline Removal by Hercynite-Biochar from the Co-Pyrolysis of Red Mud-Steel Slag-Sludge

The sludge-derived biochar is considered an effective emerging contaminants adsorbent for wastewater treatment. In this paper, red mud and steel slag (RMSS) was used for improving sludge dewaterability and enhancing the sludge-derived biochar adsorption capacity. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and a scanning electron microscope (SEM) were employed to comprehensively characterize the mineral composition, functional group, and morphology of the adsorbent. RMSS was able to improve the sludge dewatering performance by providing a skeleton structure to promote drainage and Fe(III) to decrease the Zeta potential. The dosage of 20 mg/g RMSS was able to reduce the specific resistance to filtration (SRF) and the Zeta potential of sludge from 1.57 × 1013 m/kg and −19.56 mV to 0.79 × 1013 m/kg and −9.10 mV, respectively. The co-pyrolysis of RMSS and sludge (2:8) induced the formation of biochar containing FeAl2O4 (PS80). The PS80 exhibited a large surface area (46.40 m2/g) and high tetracycline (TC) removal capacity (98.87 mg/g) when combined with H2O2 (PS80-H2O2). The adsorption process of TC onto PS80 and PS80-H2O2 was well described by the pseudo-first-order and pseudo-second-order kinetic model, indicating physisorption and chemisorption behavior. The results indicated that co-pyrolysis of RMSS sludge PS80-H2O2 could enhance the biochar adsorption capacity of TC, attributable to the degradation by ·OH generated by the heterogeneous Fenton reaction of FeAl2O4 and H2O2, the release of adsorbed sites, and the improvement of the biochar pore structure. This study proposed a novel method for the use of RMSS to dewater sludge as well as to induce the formation of FeAl2O4 in biochar with effective TC removal by providing a Fe and Al source, achieving a waste-to-resource strategy for the integrated management of industrial solid waste and sewage sludge.

Surface Modification of Biochar for Dye Removal from Wastewater

Nowadays, biochar is being studied to a great degree because of its potential for carbon sequestration, soil improvement, climate change mitigation, catalysis, wastewater treatment, energy storage, and waste management. The present review emphasizes on the utilization of biochar and biochar-based nanocomposites to play a key role in decontaminating dyes from wastewater. Numerous trials are underway to synthesize functionalized, surface engineered biochar-based nanocomposites that can sufficiently remove dye-contaminated wastewater. The removal of dyes from wastewater via natural and modified biochar follows numerous mechanisms such as precipitation, surface complexation, ion exchange, cation–π interactions, and electrostatic attraction. Further, biochar production and modification promote good adsorption capacity for dye removal owing to the properties tailored from the production stage and linked with specific adsorption mechanisms such as hydrophobic and electrostatic interactions. Meanwhile, a framework for artificial neural networking and machine learning to model the dye removal efficiency of biochar from wastewater is proposed even though such studies are still in their infancy stage. The present review article recommends that smart technologies for modelling and forecasting the potential of such modification of biochar should be included for their proper applications.

Enhanced removal of neonicotinoid pesticides present in the Decision 2018/840/EU by new sewage sludge-based carbon materials

Due to the increasingly strict legislation about the disposal of sewage sludge, it is necessary to find sustainable solutions to manage this waste at low-cost conditions. In addition, priority contaminants are now attracting much attention since they are usually detected in WWTP effluents. In this work, five sludge have been used as precursors for the synthesis of activated carbons subsequently tested in the removal by adsorption of three neonicotinoid pesticides listed in the EU Watch List: acetamiprid (ACT), thiamethoxam (THM), and imidacloprid (IMD). Generally, the activated carbons were prepared by chemical activation using ZnCl₂ as an activating agent and then the resulting materials were pyrolyzed at 800 °C for 2 h. The synthesized activated carbons showed different textural properties; thus, the best adsorption results were found for AC-Industrial activated carbon, obtained from an industrial origin sewage sludge, with high equilibrium adsorption capacities (q_e = 104.2, 137.0, and 119.9 mg g^-1), for ACT, THM, and IMD, respectively. Furthermore, it was elucidated that the use of CO₂ in the synthesis generated an opening, followed by widening, of the narrowest microporosity, increasing the specific surface area of the carbon materials. The kinetic and isotherm adsorption experimental data were obtained for each of the pesticide-activated carbon systems; thus, the kinetic curves were well-fitted to the pseudo-second-order kinetic model, as well as, Freundlich and Guggenheim-Anderson-de Boer (GAB) empirical models were used for the fitting of the equilibrium adsorption isotherms, finding that GAB model best fitted the experimental data. Additionally, the regeneration of the activated carbons using methanol as a regenerating agent and the single and simultaneous adsorption of a hospital wastewater effluent, fortified with the three studied pesticides have been explored.

Preparation of spiramycin fermentation residue derived biochar for effective adsorption of spiramycin from wastewater

Spiramycin (SPI) fermentation residue (SFR) is classified as hazardous waste in China because of the residual antibiotics in it. SFR disposal in the traditional way is costly and wasteful of resources. In this study, pyrolysis method was adopted to covert SFR to biochar for SPI removal from wastewater, and the SPI adsorption performance was investigated. The results showed that the optimal pyrolysis temperature was 700 °C as the prepared biochar BC700 exhibited the highest SPI removal efficiency. The specific surface area of BC700 was 451.68 m²/g, and the maximum adsorption capacity was 147.28 mg/g. The adsorption mechanism involved electrostatic interaction, pore filling, π-π interaction, hydrogen bonding, and the participation of C-C and O-CO functional groups in the adsorption. No residual SPI was detected in BC700 indicating the detoxification of SFR was achieved. Moreover, after recycling for 5 times, the SPI removal efficiency was still higher than 80.0%. Therefore, this study could provide a promising method for SFR disposal.

Seaweed-derived hierarchically porous carbon for highly efficient removal of tetracycline

Herein we present a facile approach for the preparation of a novel hierarchically porous carbon, in which seaweeds serve as carbon source and KOH as activator. The fabricated KOH-activated seaweed carbon (K-SC) displays strong affinity towards tetracycline with maximum uptake quantity of 853.3 mg/g, significantly higher than other tetracycline adsorbents. The superior adsorption capacity ascribes to large specific surface area (2614 m2/g) and hierarchically porous structure of K-SC, along with strong π- π interactions between tetracycline and K-SC. In addition, the as-prepared K-SC exhibits fast adsorption kinetics, capable of removing 99% of tetracycline in 30 min. Meanwhile, the exhausted K-SC can be regenerated for four cycling adsorption without an obvious degradation in capacities. More importantly, pH and ionic strengths barely affect the adsorption performance of K-SC, implying electrostatic interactions hardly play any role in tetracycline adsorption process. Furthermore, the K-SC packed fixed-bed column (0.1 g of adsorbents) can continually treat 2780 mL solution spiked with 5.0 mg/g tetracycline before reaching the breakthrough point. All in all, the fabricated K-SC equips with high adsorption capacity, fast adsorption rate, glorious anti-interference capability and good reusability, which make it hold great feasibilities for treating tetracycline contamination in real applications.

A novel g-C3N4 nanosheet/Ag3PO4/α-Bi2O3 ternary dual Z-scheme heterojunction with increased light absorption and expanded specific surface area for efficient photocatalytic removal of TC

A novel ternary dual Z-scheme 2D g-C₃N₄ nanosheet/Ag₃PO₄/α-Bi₂O₃ (CNN/AP/BO) photocatalyst was successfully synthesized by an in situ deposition and hydrothermal-calcination method. The coupling of AP and BO remarkably enhanced the photocatalytic tetracycline (TC) degradation under visible light illumination, with an optimal removal efficiency of 91.6% (60 min), which can be attributed to the extended visible-light absorption and increased specific surface area owing to the interfacial intimate coupling with well-matched energy band positions between semiconductors. The improved photocatalytic activity resulted from the abundant free radicals by the order of ˙O₂^- > h⁺ > ˙OH based on the electron spin resonance (ESR) and quenching experiment results. In addition, the possible mechanism of TC degradation over the ternary dual Z-scheme heterojunction CNN/AP/BO was proposed.

Preparation of structured biochar, its adsorption capacity of N and P and its characterization

Structured biochar (SC) was prepared by biochar from cattail-sludge mixture (CS) and high-density polyethylene (HDPE) and treated as an adsorbent, and the KH₂PO₄ and NH₄Cl solution were treated as adsorbates, to explore the adsorption capacity of phosphorus (P) and nitrogen (N) on SC in water. A single factor experimental method was employed to determine the optimal parameters for SC. The results showed that: 60% sizing amount, 5 N (cm²)^-1 molding pressure, 160 °C molding temperature and 95 min molding time were optimal parameters for SC preparation. The adsorption of P and N on SC conforms to the Langmuir model, with the distribution of adsorption sites on the surface tending to be even. The adsorption of P and N on SC is favorable and spontaneous, and the adsorption tends to be monolayer adsorption with a major role for chemical adsorption. The higher the temperature, the higher the adsorption capacity of P and N on SC is, and the affinity of SC with P is higher than that with N. The pseudo-second-order kinetic model for the adsorption of N and P by SC has a high degree of fit. The pH_pzc value of SC was 8.57. The hydrophobicity and stability of SC are rather high, with the surface particles closely bonded and increased roughness and pore diameter. The adsorption mechanism of P and N on SC can be attributed to pore filling, electrostatic attraction and hydrogen bonding. The results can provide a new technology for the resource utilization of cattails and sludge, a new idea for the recycling and reuse of biochar, and a basis for the selection of materials for the treatment of eutrophic water bodies.

Enhanced Tetracycline Removal from Highly Concentrated Aqueous Media by Lipid-Free Chlorella sp. Biomass

Microalgae are used as a lipid source for different applications, such as cosmetics and biofuel. The nonliving biomass and the byproduct from the lipid extraction procedure can efficiently remove antibiotics. This work has explored the potential use of Chlorella sp. biomasses for tetracycline (Tc) removal from highly concentrated aqueous media. Non-living biomass (NLB) is the biomass before the lipid extraction procedure, while lipid-extracted biomass (LEB) is the byproduct mentioned before. LEB removed 76.9% of Tc at 40 mg/L initial concentration and 40 mg of biomass, representing an adsorption capacity of 19.2 mg/g. Subsequently, NLB removed 68.0% of Tc at 50 mg/L and 60 mg of biomass, equivalent to 14.2 mg/g of adsorptive capacity. These results revealed an enhanced removal capacity by LEB compared with NLB and other microalgae-based materials. On the other hand, the adsorption kinetics followed the pseudo-second-order and Elovich models, suggesting chemisorption with interactions between adsorbates. The adsorption isotherms indicate a multilayer mechanism on a heterogeneous surface. Additionally, the interactions between the surface and the first layer of tetracycline are weak, and the formation of the subsequent layers is favored. The Chlorella sp. biomass after the lipid extraction process is a promising material for removing tetracycline; moreover, the use of this residue contributes to the zero-waste strategy.

An efficient, green and sustainable potassium hydroxide activated magnetic corn cob biochar for imidacloprid removal

The extensive use of imidacloprid (IMI) has led to its being frequently detected in natural water, also caused the potential damage to the ecosystem. Development of efficient, green and sustainable technique is demanded to eliminate this problem. A novel biochar (KMCBC) derived from agriculture waste of corn cob was first time co-modified by potassium hydroxide (KOH), ferric chloride (FeCl₃) and zinc chloride (ZnCl₂), which showed the greater adsorption amount (410 mg g^-1 at 298 K) for imidacloprid (IMI). Pseudo-second-order kinetic and Langmuir isotherm models fitted well with the experimental data, together with the physicochemical characterization analysis, demonstrating that the adsorption process of IMI by KMCBC might be mainly controlled by micropore filling, π-π electron donor-acceptor and functional groups interactions (H-bonding and complexation). Additionally, the thermodynamics parameters suggested that IMI adsorption in this study was a spontaneous, endothermic and randomly increasing process. Besides, KMCBC owned the easy separation performance and promising environmental safety, also exhibited a high selective adsorption capacity regardless of solution pH (its optimum adsorption performance for IMI was obtained at pH = 5), inorganic ions strength and humic acid (HA) concentrations. The regenerated KMCBC (synergistic ultrasound/ethanol) could sustainably and efficiently adsorb IMI in the reuse cycles. Therefore, this study provided an efficient, green and sustainable adsorbent of KMCBC for IMI removal.

Synthesis of magnetic hydrochar from Fenton sludge and sewage sludge for enhanced anaerobic decolorization of azo dye AO7

A novel magnetic hydrochar synthesized from Fenton sludge (FS) and sewage sludge (SS) was employed in the anaerobic decolorization of acid orange 7 (AO7). The stable presence of Fe₃O₄ in magnetic hydrochar was confirmed by physicochemical characterization. The degradation efficiency of AO7 in the anaerobic system with the addition of hydrochar prepared in an optimal proportion (SS:FS=1:3, named as HC-1:3) could reach 98.55%, which was 1.91 times higher than the control system. Particularly, superior electrical conductivity, electron transport system activity and azo reductase activity of the sludge in anaerobic system with HC-1:3 were achieved. The redox of Fe(Ⅲ)/Fe(Ⅱ) in anaerobic system was realized by dissimilatory iron-reducing bacteria enriched with HC-1:3. According to the six-cycle batch experiments and 120-day continuous-flow UASB experiments, the addition of HC-1:3 into the anaerobic system facilitated the diversity of microbiological community and increased the ecological stability of anaerobic system. The possible electron transfer mechanism involving in the magnetic hydrochar-based anaerobic system for AO7 removal was speculated preliminarily. The as-prepared magnetic hydrochar not only showed a promising future in anaerobic system for recalcitrant contaminants degradation, but also provided a new approach for the resource utilization of FS and SS.

Rapid and efficient adsorption of tetracycline from aqueous solution in a wide pH range by using iron and aminoacetic acid sequentially modified hierarchical porous biochar

The object of this work was to synthesize an iron and aminoacetic acid sequentially modified hierarchical porous biochar (AC-Fe@HPBC) for tetracycline (TC) removal from aqueous solution. Results showed that AC-Fe@HPBC had a larger surface area (362.5370 m²/g), developed microporous structure (0.1802 cm³/g), and numerous functional groups, which provided more adsorption sites. The maximum adsorption capacity towards TC by AC-Fe@HPBC was 457.85 mg/g, 1.43, 1.29 and 1.20-fold than that of HPBC, AC@PHBC and Fe@HPBC, respectively, and the super-fast adsorptive equilibrium was achieved within 10 min. Additionally, introducing amino and carboxyl functional groups on the AC-Fe@HPBC surface significantly broadened the operation pH range (3-11). Site energy analysis indicated TC and AC-Fe@HPBC had stronger adsorption affinity at a higher temperature. The adsorption mechanism involved pore filling, surface complexation, H-bond and π-π interaction. Moreover, the reusability experiments proved AC-Fe@HPBC as an effective adsorbent for TC removal from aqueous solution.

Removal of pharmaceuticals from water using sewage sludge-derived biochar: A review

In recent years, considerable attention has been paid to the beneficial utilization of sewage sludge to reduce the risks associated with sludge disposal. Besides other applications of sludge, biochar produced from sludge has also been employed for the elimination of various pollutants from water. This review critically evaluates the recent progress in applications of sludge-based biochar for the adsorption of pharmaceuticals from water. The synthesis techniques of biochar production from sludge and their effects on physicochemical characteristics of produced biochar are discussed. The removal of various pharmaceuticals by sludge-based biochar are described in detail, with the emphasis on the adsorption mechanism and their reusability potential. It is evident from the literature that sludge-based biochar has demonstrated excellent potential for the adsorption of numerous pharmaceuticals from the aqueous phase. The major hurdles and issues related to the synthesis of sludge-based biochar and applications are highlighted, with reference to the adsorption of pharmaceuticals. Finally, a roadmap is suggested along with future research directions to ensure the sustainable production of biochar from sludge and its applications in water treatment.

Characteristics of Cu(II)-modified aerobic granular sludge biocarbon in removal of doxycycline hydroxide

In this study, the biocarbon derived from aerobic granular sludge with different nutritive proportions was modified by Cu(NO₃)₂•3H₂O (Cu-BC) to improve its adsorption capacity of doxycycline hydrochloride (DOX). The surface area, pores, functional groups, and element composition of biocarbon were characterized by scanning electron microscopy (SEM), Brunauer-Emmett-Teller (BET) surface area, X-ray photoelectron spectrometer, X-ray diffraction (XRD), the X-ray photoelectron spectrometer, and Fourier transform infrared spectrometry (FT-IR), respectively. Effects of DOX concentration, initial pH, and background electrolyte on adsorption effects of composite were analyzed. Furthermore, the adsorption kinetics, isotherm, thermodynamics, and diffusion model were investigated. Results demonstrated that biocarbons which were prepared with aerobic granular sludge under different nutritive proportions presented different performances. The BET specific surface area of Cu-NaAC/AGS-BC was 260.1592 m²/g, and the micropore volume was 0.054101 cm³/g. The BET specific surface area of Cu-GLC /AGS-BC was only 10.6821 m²/g, and the micropore volume was 0.008687 cm³/g. Both kinds of modified biochar contain a large number of oxygen-containing functional groups. The highest adsorption efficiency of Cu-BC could reach 99.54%. The adsorption of DOX on two modified biocarbons conforms to the pseudo-second-order dynamic model and Temkin isothermal model.

Tetracycline adsorption mechanisms by NaOH-modified biochar derived from waste Auricularia auricula dregs

Tetracycline (TC) is not easy to degrade in human or animal and can even be converted to more toxic substances. The overuse and wanton discharge of TC also caused serious problem of water pollution. This study investigated the removal of TC by biochar (BC) prepared from waste Auricularia auricula dregs and modified with NaOH by characterizing the pH and adsorption kinetics, and using isotherm models. Three BC samples were prepared and that produced using the highest concentration of NaOH (8 M) was more suitable for removing TC, where the adsorption amount was 26.65 mg/g. Pseudo-second order and Freundlich models both fitted well to the adsorption kinetics, and diffusion of the liquid film was considered the rate-controlling step. The multivariate mechanism involved electron interplay, H-bonding, and π-π electron donor-acceptor interactions. The results of this work can not only make the waste Auricularia auricula dregs resourceful, but also provide a new method for the removal of TC in wastewater, which is of great practical significance.

Facile synthesis of Fe-modified lignin-based biochar for ultra-fast adsorption of methylene blue: Selective adsorption and mechanism studies

A novel Fe-modified lignin-based biochar (Fe-LB) was fabricated via a facile one-step carbonization method for methylene blue (MB) removal from wastewater. Fe-LB exhibited a high specific surface area (885.97 m²/g) and micropore volume (0.3203 m³/g), and demonstrated high affinity for MB with the maximum adsorption capacity of 2.7-fold by Fe-LB than LB. It was found that quick adsorption could be achieved in 15 min with the MB removal efficiency of 100% and adsorption capacity reached 200 mg/g. Selective adsorption studies indicated that Fe-LB preferentially adsorbed MB in high salt and multiple dye systems (binary, ternary, and quaternary) over a wide pH range from 2 to 12. The removal efficiency of CR was greatly improved due to the synergistic effect between MB and CR in the binary system. This work demonstrated that Fe-LB can effectively remove dye contaminants and possessed great potential in the treatment of MB polluted dye wastewater.

Application of layered double hydroxide-biochar composites in wastewater treatment: Recent trends, modification strategies, and outlook

In recent years, layered double hydroxide-biochar (LDH-BC) composites as adsorbents and catalysts for contaminants removal (inorganic anions, heavy metals, and organics) have received increasing attention and became a new research point. It is because of the good chemical stability, abundant surface functional groups, excellent anion exchange ability, and good electronic properties of LDH-BC composites. Hence, we offer an overall review on the developments and processes in the synthesis of LDH-BC composites as adsorbents and catalysts. Special attention is devoted to the strategies for enhancing the properties of LDH-BC composites, including (1) magnetic treatment, (2) acid treatment, (3) alkali treatment, (4) controlling metal ion ratios, (5) LDHs intercalation, and (6) calcination. In addition, further studies are called for LDH-BC composites and potential areas for future application of LDH-BC composites are also proposed.

Highly Mesoporous g-C3N4 with Uniform Pore Size Distribution via the Template-Free Method to Enhanced Solar-Driven Tetracycline Degradation

A highly mesoporous graphitic carbon nitride g-C3N4 (GCN) has been produced by a template-free method and effectively photodegrade tetracycline (TC) antibiotic under solar light irradiation. The mesoporous GCN (GCN-500) greatly improves the photoactivity (0.0247 min-1) by 2.13 times, as compared to that of bulk GCN (0.0116 min-1). The efficiently strengthened photoactivity is ascribed to the high porosity (117.05 m2/g), and improves the optical absorption under visible light (Eg = 2.65 eV) and good charge carrier separation efficiency. The synthesized mesoporous GCN shows a uniform pore size (~3 nm) distribution. GCN-500 shows large pore volume (0.210 cm3/g) compared to GCN-B (0.083 cm3/g). Besides, the GCN-500 also exhibits good recyclability and photostability for TC photodegradation. In conclusion, GCN-500 is a recyclable photocatalyst for the removal of TC under visible light irradiation.

Preparation of ultrahigh-surface-area sludge biopolymers-based carbon using alkali treatment for organic matters recovery coupled to catalytic pyrolysis

In this work, we employed waste activated sludge (WAS) as carbon source to prepare ultrahigh specific surface area (SSA) biopolymers-based carbons (BBCs) through alkali (KOH) treatment coupled to pyrolysis strategy. Before the pyrolysis process, the involvement of KOH made a great recovery of soluble biopolymers from WAS, resulting in highly-efficient catalytic pyrolysis. The Brunner-Emmett-Teller and pore volume of BBCs prepared at 800°C (BBC₈₀₀) reached the maximum at 2633.89 m²·g^-1 and 2.919 m³·g^-1, respectively. X-ray photoelectron spectroscopy suggested that aromatic carbon in the form of C=C was the dominant fraction of C element in BBCs. The N element in BBCs were composed of pyrrolic nitrogen and pyridinic nitrogen at 700°C, while a new graphitic nitrogen appeared over 800°C. As a refractory pollutant of wastewater treatment plants, tetracycline (TC) was selected to evaluate adsorption performance of BBCs. The adsorption behavior of BBCs towards TC was conformed to the pseudo-second-order kinetic and the Langmuir models, signifying that chemisorption of monolayers was dominant in TC adsorption. The adsorption capacity of BBC₈₀₀ reached the maximum at 877.19 mg·g^-1 for 90 min at 298 K. Thermodynamic analysis indicated that the adsorption process was endothermic and spontaneous. Hydrogen bonding and π-π stacking interaction were mainly responsible for TC adsorption, and interfacial diffusion was the main rate-control step in adsorption process. The presence of soluble microbial products (SMPs) enhanced TC removal. This work provided a novel strategy to prepare bio-carbon with ultrahigh SSA using WAS for highly-efficient removal of organic pollutants.