Air concentrations of PCDD/Fs, PCBs and PCNs using active and passive air samplers

Regulatory compliance of PCDD/F emissions by a municipal solid waste incinerator. A case study in Sant Adrià de Besòs, Catalonia, Spain

Despite incineration is an important emission source of toxic pollutants, such as heavy metals and polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), it is still one of the most widely used methods for the management of municipal solid waste. The current paper summarizes the results of a 20-year follow-up study of the emissions of PCDD/Fs by a municipal solid waste incinerator (MSWI) in Sant Adrià de Besòs (Catalonia, Spain). Samples of ambient air, soils and herbage were periodically collected near the facility and the content of PCDD/Fs was analyzed. In the last (2017) survey, mean levels in soil were 3.60 ng WHO-TEQ/kg (range: 0.40-10.6), being considerably higher than the mean concentrations of PCDD/Fs in soil samples collected near other MSWIs in Catalonia. Moreover, air PCDD/F concentrations were even higher than those found in a previous (2014) survey, as they increased from 0.026 to 0.044 pg WHO-TEQ/m3. Ultimately, the PCDD/F exposure would be associated to a cancer risk (2.5 × 10-6) for the population living in the surrounding area. Globally, this information indicates that the MSWI of Sant Adrià de Besòs could have had a negative impact on the environment and potentially on public health, being an example of a possible inappropriate management for years. The application of Best Available Techniques to minimize the emission of PCDD/Fs and other chemicals is critical.

The long-term spatial and temporal distributions of polychlorinated naphthalene air concentrations in Fildes Peninsula, West Antarctica

The knowledge of polychlorinated naphthalenes (PCNs) in the Antarctic atmosphere is quite limited compared to the Arctic. PCNs are a global concern because of their PBT characteristics (i.e., persistent, bioaccumulative, and toxic) and severe and often deadly biological effects on people and other animals. Therefore, the present study used a passive air sampling method to conduct long-term air monitoring of PCNs for almost a decade from 2013 to 2022, specifically on Fildes Peninsula, situated on King George Island, located in West Antarctica. The median sum of mono-CNs to octa-CN concentration (∑75PCNs) in the Antarctic atmosphere was 12.4 pg/m3. In terms of homologues, mono-CNs to tri-CNs predominated. Among these, the prevalent congeners observed were PCN-1 and PCN-2, originating from mono-CNs, followed by PCN-5/7 from di-CNs, and PCN-24/14 from tri-CNs, respectively. Between 2013 and 2022, the total levels of PCNs were found to have decreased approximately fourfold. Ratio analyses and principal component analysis (PCA) showed that the long-range atmospheric transport and combustion-related sources as the potential PCN sources in the study area. This paper provides the most up-to-date temporal trend analysis of PCNs in the Antarctic continent and is the first to document all 75 congeners (mono-CNs to octa-CN homologue groups).

Concentrations of PCDD/Fs and dl-PCBs in ambient air in Hanoi, Vietnam, between 2017 and 2021, and health risk assessments

The concentrations and seasonal and temporal variations in polychlorodibenzo-p-dioxins/polychlorodibenzofurans (PCDD/Fs) and dioxin-like polychlorobiphenyls (dl-PCBs) in ambient air from November 2017 to September 2021 were investigated via passive air samplers containing polyurethane foam (PUF) discs in three residential areas: the Cau Giay (CG) urban, Quang Minh (QM) industrial-suburban, and Ba Vi (BV) rural areas, Hanoi, Vietnam. The average total toxic equivalents (TEQs) of PCDD/Fs and dl-PCBs (∑TEQs), using WHO2005-TEFs, were highest in the QM area (506 fg WHO-TEQ/PUF day) and ranged from 317 to 752 fg WHO-TEQ/PUF day. Compared to that in the QM area, the average ∑TEQs were lower in the CG area, ranging between 372 and 615 fg WHO-TEQ/PUF day with an average value of 482 fg WHO-TEQ/PUF day. The average ∑TEQs were lowest in the BV area, ranging from 121 to 414 fg WHO-TEQ/PUF day with an average of 231 fg WHO-TEQ/PUF day. PCDD/F and dl-PCB air pollution increased during spring and winter. The highest seasonal average ∑TEQs in the CG area was 534 fg WHO-TEQ/PUF day in winter. The highest average ∑TEQs in the QM and BV areas were 653 and 280 fg WHO-TEQ/PUF day in spring, respectively. The average daily dose (ADD) values of PCDD/Fs and dl-PCBs through inhalation for adults in the three areas were minimal (9.9-96.2 fg WHO-TEQ/kg body weight (BW)/day) and below the 10% threshold of the tolerable daily intake (TDI) value recommended by the WHO (100-400 fg WHO-TEQ/kg BW/day). For children, the ADD values (15.1-244 fg WHO-TEQ/kg BW/day) were less than and within 10% of the recommended TDI value.

Characterization of PCDD/F and dl-PCB levels in air in Gipuzkoa (Basque Country, Spain)

This research examines the levels and trends of pollutants, specifically 17 congeners of PCDD/Fs and 12 dl-PCBs, in the air measured in the province of Gipuzkoa (Basque Country, Spain). The study used PCDD/Fs, dl-PCB, and the sum of dioxin-like compounds as separate response variables. A total of 113 air samples were collected and analyzed using the method described in the European Standard (EN-1948:2006) from two industrial areas. The results were analyzed using non-parametric test to assess the variability of these pollutants based on different factors (year, season and day of the week) and General Linear Models to assess the weight of each factor. The study found that the toxic equivalents (TEQs) for PCDD/Fs were 12.29 fg TEQm^-3 and for dl-PCBs were 1.63 fg TEQm^-3, which were in a similar range or lower than those observed in other national and international studies in industrial areas. The results showed temporal variations, with higher levels of PCDD/Fs in autumn-winter than in spring-summer and higher levels of PCDD/Fs and dl-PCBs during weekdays than on weekends. The industrial area where the energy recovery plant (ERP) will be located had higher levels of air pollutants due to the presence of two PCDD/Fs emitting industries nearby, as indicated by the Spanish Registry of Polluting Emission Sources. Both industrial areas showed similar profiles of PCDD/Fs and dl-PCBs, with the PCDD/F profiles dominated by OCDD, 1,2,3,4,6,7,8-HpCDD, and 1,2,3,4,6,7,8-HpCDF in terms of concentrations and 1,2,3,7,8-PeCDD, 2,3,4,7,8-PeCDF, and 2,3,7,8-TCDD in terms of TEQs. The dl-PCB profiles were dominated by PCB 118, PCB 105, and PCB 77 in terms of concentrations and PCB 126 in terms of TEQs. The findings of this study can serve as an indicator of the potential impact of ERP on the health of the resident population and the environment.

Spatial and temporal trends of polychlorinated naphthalenes in the Arctic atmosphere at Ny-Ålesund and London Island, Svalbard

Polychlorinated naphthalenes (PCNs) are ubiquitous atmospheric pollutants that can even be found in the most remote region of the Arctic. However, temporal trend analysis and reports on mono- to octa-CN in the Arctic air are still scarce. In the present study, 8 years of atmospheric monitoring data of PCNs on Svalbard was investigated using XAD-2 resin passive air samplers (PASs) from 2011-2019. The concentrations of ∑₇₅ PCNs in the Arctic air ranged from 4.56 to 85.2 pg/m³, with a mean of 23.5 pg/m³. The mono-CNs and di-CNs were the dominant homologue groups accounting for 80 % of the total concentrations. The most abundant congeners were PCN-1, PCN-2, PCN-24/14, PCN-5/7, and PCN-3, respectively. A declining time trend of PCN concentration was observed from 2013 to 2019. The reduction in PCN concentrations is likely due to declining global emissions and banned production. However, no significant spatial difference was observed among the sampling sites. The total PCN toxic equivalency (TEQ) concentrations in the Arctic atmosphere ranged from 0.043 to 1.93 fg TEQ/m³ (mean 0.41 fg TEQ/m³). The fraction of combustion-related congeners to ∑PCNs (tri- to octa-CN) analysis results indicated that the sources of PCNs in the Arctic air were contributed mainly from reemissions of historical Halowax mixtures and combustion-related sources. To the best of our knowledge, this is the first research to report all 75 PCN congeners and homologue groups in Arctic air. Therefore, this study provides data on recent temporal trend analysis as well as all the 75 PCN congeners in the Arctic atmosphere.

PCDD/F and DL-PCB exposure among residents upwind and downwind of municipal solid waste incinerators and source identification

Understanding the environmental and human impacts associated with polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDD/Fs) and dioxin-like polychlorinated biphenyls (DL-PCBs) exposure from municipal solid waste incinerators (MSWIs) is challenging because information on ambient and dietary exposure levels, spatial characteristics, and potential exposure routes is limited. In this study, 20 households from two villages located on the upwind and downwind sides of a MSWI were selected to characterize the concentration and spatial distribution of PCDD/F and DL-PCB compounds in ambient and food samples, such as dust, air, soil, chicken, egg, and rice samples. The source of exposure was identified using congener profiles and principal component analysis. Overall, the dust and rice samples had the highest and lowest mean dioxin concentrations, respectively. Significant differences were observed (p < 0.01) in PCDD/F concentrations in chicken samples and DL-PCB concentrations in rice and air samples between the upwind and downwind villages. The exposure assessment indicated that the primary risk source was dietary exposure, especially from eggs, which had a PCDD/F toxic equivalency (TEQ) range of 0.31-14.38 pg TEQ/kg body weight (bw)/day, leading to adults in one household and children in two households exceeding the World Health Organization-defined threshold of 4 pg TEQ/kg bw/day. Chicken was the main contributor to the differences between upwind and downwind exposure. Based on the established congener profiles, the exposure routes of PCDD/Fs and DL-PCBs from the environment to food to humans were clarified.

The toxicological profile of polychlorinated naphthalenes (PCNs)

The legacy of polychlorinated naphthalenes (PCNs) manufactured during the last century continues to persist in the environment, food and humans. Metrological advances have improved characterisation of these occurrences, enabling studies on the effects of exposure to focus on congener groups and individual PCNs. Liver and adipose tissue show the highest retention but significant levels of PCNs are also retained by the brain and nervous system. Molecular configuration appears to influence tissue disposition as well as retention, favouring the higher chlorinated (≥ four chlorines) PCNs while most lower chlorinated molecules readily undergo hydroxylation and excretion through the renal system. Exposure to PCNs reportedly provokes a wide spectrum of adverse effects that range from hepatotoxicity, neurotoxicity and immune response suppression along with endocrine disruption leading to reproductive disorders and embryotoxicity. A number of PCNs, particularly hexachloronaphthalene congeners, elicit AhR mediated responses that are similar to, and occur within similar potency ranges as most dioxin-like polychlorinated biphenyls (PCBs) and some chlorinated dibenzo-p-dioxins and furans (PCDD/Fs), suggesting a relationship based on molecular size and configuration between these contaminants. Most toxicological responses generally appear to be associated with higher chlorinated PCNs. The most profound effects such as serious and sometimes fatal liver disease, chloracne, and wasting syndrome resulted either from earlier episodes of occupational exposure in humans or from acute experimental dosing of animals at levels that reflected these exposures. However, since the restriction of manufacture and controls on inadvertent production (during combustion processes), the principal route of human and animal exposure is likely to be dietary intake. Therefore, further investigations should include the effects of chronic lower level intake of higher chlorinated PCN congeners that persist in the human diet and subsequently in human and animal tissues. PCNs in the diet should be evaluated cumulatively with other similarly occurring dioxin-like contaminants.

Graphical tools for the planning and interpretation of polyurethane foam based passive air sampling campaigns

Due to low cost and easy handling during sampling and extraction, passive air samplers (PASs) using polyurethane foam (PUF) as a sorbent have become the most commonly deployed PASs for semi-volatile organic compounds (SVOCs). However, depending on the scenario, PUF-PAS may not always be operating in the linear uptake phase, which implies the need to consider how temperature, wind speed, deployment length and chemical properties interact to determine the amount of a target chemical taken up and the fraction of a depuration compound (DC) being lost during deployment. Guidance is, therefore, necessary to quantitatively interpret curvi-linear uptake in the PUF-PAS and avoid selection of DCs unsuited to the deployment conditions. In this study, the PAS-SIM model is used to generate graphical tools that aid in addressing important questions frequently arising during the use of PUF-PASs. Specifically, we generated five charts that display (i) the inherent sampling rate as a function of wind speed and a chemical's molecular diffusivity, (ii) the length of the linear uptake period as a function of chemical properties, temperature and the acceptable deviation from linearity, (iii) the time to 95% equilibrium as influenced by chemical properties, temperature and wind speed, (iv) the dependence of the fractional loss of DCs on chemical properties, temperature, wind speed and deployment length, and (v) the influence of chemical properties, temperature and the total suspended particle concentration on the extent of sorption to atmospheric particles. The charts also facilitate the assessment of the influence of parameter uncertainty. It is hoped that these charts assist with planning and interpreting sampling campaigns based on a mechanistic and quantitative understanding of uptake in PUF-based PASs.

Field comparison of passive polyurethane foam and active air sampling techniques for analysis of gas-phase semi-volatile organic compounds at a remote high-mountain site

Polyurethane foam passive air samplers (PUF-PAS) are good candidates for the determination of gas-phase semi-volatile organic compound (SVOC) air concentrations in high-mountain areas over long periods because they do not require an energy supply. However, the harsh meteorological conditions present in such locations can increase the uncertainties inherently associated to PAS sampling rates due to the many variables involved in their calculation and to the assumptions made regarding PUF diffusive uptake mechanics, which can considerably bias the resulting concentrations. Therefore, we studied the performance of PUF-PASs in a remote location in the Pyrenees mountain range for the analysis of several SVOCs in air, including polychlorobiphenyls (PCBs), hexachlorobenzene, pentachlorobenzene, polycyclic aromatic hydrocarbons (PAHs), and the less studied emerging organophosphate flame retardants (OPFRs). An in-situ PUF-PAS calibration using Performance Reference Compounds (PRCs) provided compound- and sampler-specific sampling rates, showing mean experimental errors (12%) that adequately conformed to an estimate of their expanded theoretical uncertainties (15%). This showcases the suitability of this calibration strategy in an area with conditions beyond those typically considered in calibration efforts available to date. Moreover, gas-phase concentrations of the studied pollutants from PUF-PAS samples showed very good agreement (R² up to 0.91, p < 0.01) when compared to those obtained using a conventional high-volume active air sampler (PUF-AAS), with some minor deviations observed for PAHs caused by the seasonality in their atmospheric concentrations. No relevant levels of pollutants preferentially bound to the particle phase were detected in the PUF-PASs, the particle infiltration efficiency of the sampler configuration used was found to be low, and compounds typically distributed between the gas and particle phases of AAS samples revealed profiles consistent with their vapor pressures, except for some OPFRs.

Regional characteristics of atmospheric δ34S-SO42- over three parts of Asia monitored by quartz wool-based passive samplers

A new method is presented for measuring atmospheric contents and δ³⁴S-SO₄^2- in airborne particulate matter using quartz wool disk passive air samplers (Pas-QW). The ability of Pas-QW samplers to provide time-integrated measurements of atmospheric SO₄^2- was confirmed in a field calibration study. The average sampling rate of SO₄^2- measured was 2.3 ± 0.3 m³/day, and this was not greatly affected by changes in meteorological parameters. The results of simultaneous sampling campaign showed that the average SO₄^2- contents in Pakistan and the Indochina Peninsula (ICP) were relatively lower than that of China. The spatial distribution of SO₄^2- concentrations was largely attributed to the development of the regional economies. The range of δ³⁴S values observed in Pakistan (4.3 ± 1.4‰) and the ICP (4.5 ± 1.2‰) were relatively small, while a large range of δ³⁴S values was observed in China (3.9 ± 2.5‰). The regional distribution of sulfur isotope compositions was significantly affected by coal combustion. A source analysis based on a Bayesian mixing model showed that 80.4 ± 13.1% and 19.6 ± 13.1% of artificial sulfur dioxide (SO₂) sources in China could be attributed to coal combustion and oil combustion, respectively. The two sources differed greatly between regions, and the contribution of oil combustion in cities was higher than previously reported data obtained from emission inventories. This study confirmed that the Pas-QW is a promising tool for simultaneously monitoring atmospheric δ³⁴S-SO₄^2- over large regions, and that the results of the isotope models can provide a reference for the compilation of SO₂ emission inventories.

Evaluation of atmospheric sources of PCDD/Fs, PCBs and PBDEs around an MSWI plant using active and passive air samplers

This study evaluated the spatial distributions and concentrations of polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs), polychlorinated biphenyls (PCBs) and polybrominated diphenyl ethers (PBDEs) in ambient air around a municipal solid waste incineration (MSWI) plant located in eastern China in two sampling campaigns within one year. Twenty high-volume samples and 27 passive air samples were collected from May 2012 to May 2013. The mean sampling rate of the passive sampler was estimated to be 3.8 ± 1.8 m³ d^-1 in summer and autumn, while the mean sampling rate was 2.8 ± 1.0 m³ d^-1 in winter and spring. Hence, the annual mean sampling rate was approximately 3.2 ± 1.4 m³ d^-1. The mean levels of PCDD/Fs, PCBs, PBDEs (excluding BDE-209) and BDE-209 in the passive air samples varied in the ranges of 0.086 ± 0.058-0.76 ± 0.51 pg TEQ m^-3, 39 ± 26-170 ± 120 pg m^-3, 3.3 ± 2.2-36 ± 24 pg m^-3 and 58 ± 39-300 ± 150 pg m^-3, respectively. The levels, congener profiles and spatial distributions of PCDD/Fs, PCBs and PBDEs were investigated. The results showed that the concentrations of PCDD/Fs and PCBs decreased with increasing distance from the emission source and that different sampling sites had slightly different effects. However, this trend was opposite to that observed for PBDEs. Moreover, principal component analysis (PCA) demonstrated that the MSWI emission source was the primary factor for PCDD/Fs in ambient air. Further monitoring should be conducted to evaluate the noticeable impact on the environment and human health due to exposure.

Main sources controlling atmospheric burdens of persistent organic pollutants on a national scale

National long-term monitoring programs on persistent organic pollutants (POPs) in background air have traditionally relied on active air sampling techniques. Due to limited spatial coverage of active air samplers, questions remain (i) whether active air sampler monitoring sites are representative for atmospheric burdens within the larger geographical area targeted by the monitoring programs, and thus (ii) if the main sources affecting POPs in background air across a nation are understood. The main objective of this study was to explore the utility of spatial and temporal trends in concert with multiple modelling approaches to understand the main sources affecting polychlorinated biphenyls (PCBs) and organochlorine pesticides (OCPs) in background air across a nation. For this purpose, a comprehensive campaign was carried out in summer 2016, measuring POPs in background air across Norway using passive air sampling. Results were compared to a similar campaign in 2006 to assess possible changes over one decade. We furthermore used the Global EMEP Multi-media Modeling System (GLEMOS) and the Flexible Particle dispersion model (FLEXPART) to predict and evaluate the relative importance of primary emissions, secondary emissions, long-range atmospheric transport (LRAT) and national emissions in controlling atmospheric burdens of PCB-153 on a national scale. The concentrations in air of both PCBs and most of the targeted OCPs were generally low, with the exception of hexachlorobenzene (HCB). A limited spatial variability for all POPs in this study, together with predictions by both models, suggest that LRAT dominates atmospheric burdens across Norway. Model predictions by the GLEMOS model, as well as measured isomeric ratios, further suggest that LRAT of some POPs are dictated by secondary emissions. Our results illustrate the utility of combining observations and mechanistic modelling approaches to help identify the main factors affecting atmospheric burdens of POPs across a nation, which, in turn, may be used to inform both national monitoring and control strategies.

Ambient air monitoring around the dioxin remediation site in Da Nang, Vietnam, using passive air samplers

The concentrations and temporal variations of polychlorodibenzo-p-dioxins and polychlorodibenzofurans (PCDDs/PCDFs) in ambient air between March 2013 and February 2017 were investigated by passive air samplers containing polyurethane foam (PUF) disks in the dioxin remediation area using in-pile thermal desorption (IPTD) technology at Da Nang airport, Vietnam. The PCDD/PCDF concentrations in ambient air at each site depended on the location of the emission sources and the wind direction, the dioxin contamination level of excavated materials, the periods of excavation and transport, and the operation of the IPTD treatment system. The PCDD/PCDF concentrations were the highest in the former Agent Orange mixing and loading area (AOMLA), which was the closest to the IPTD system, with total toxic equivalent (TEQ) values ranging from 0.437 to 15.3 pg/PUF/day. The total TEQ concentrations in the Sen Lake area ranged from 0.138 to 2.41 pg/PUF/day. The lowest concentration of PCDDs/PCDFs occurred in the northern perimeter area, with total TEQ values ranging from 0.164 to 0.972 pg/PUF/day. The decreasing trend of the PCDD/PCDF concentrations in ambient air was confirmed over time at all three monitoring sites, among which there was a strong decrease in the former AOMLA after February 2015. Residents living near the Da Nang airport were at a low risk of being exposed to PCDDs/PCDFs through inhalation during remediation project implementation, while residents living close to the former AOMLA faced elevated risks with an average daily dose of PCDDs/PCDFs through inhalation ranging from 0.017 to 0.82 pg TEQ/kg body weight/day.

Dioxins and dioxin-like PCBs in the ambient air of the Valencian Region (Spain): Levels, human exposure, and risk assessment

Dioxins (polychlorinated dibenzo-p-dioxins (PCDD) and polychlorinated dibenzofurans (PCDF), as well as dioxin-like PCBs (dl-PCBs), are listed as persistent organic pollutants in the Stockholm Convention. In this study, we measured their concentrations in the particulate phase (PM10) of the ambient air in seven monitoring stations of the Valencian Community (Spain). A total of 82 samples were collected from different sampling sites: four industrial, two urban, and one remote, from February to December 2019. The total concentrations of the sum of PCDD, PCDF, and dl-PCBs ranged from 2.90 fg TEQ/m³ to 317.98 fg TEQ/m³. Risk assessment for adults and children was performed using both daily and chronic exposure. Each station showed its specific dioxin profile, related to the main productive activities in each area. The daily inhalation dose (DID) in adults and children was lower than the tolerable daily intake (TDI) of 1-4 pg WHO TEQ kg^-1 b.w. d^-1 for dioxins. In the case of chronic exposure, the cancer risk for dioxins and dl-PCBs was estimated at values ranging from 5.27 E-07 to 5.52 E-05. The cancer risk for dioxins and PCBs estimated at the 95th percentile was higher than 1.0 E-06 in all of the industrial and urban areas.

Characterization, source apportionment, air/plant partitioning and cancer risk assessment of atmospheric PAHs measured with tree components and passive air sampler

In this study, ambient air and olive tree components (leaf and branch) were simultaneously collected and analyzed for polycyclic aromatic hydrocarbons (PAHs) to investigate their levels and accumulations, temporal variations, possible sources, air-plant partitioning and cancer risks for 12 months. During the sampling period, total of 14 PAH (∑₁₄PAH) concentrations measured in the olive leaves (dissolved and particle phase) and braches (1- and 2-year-old) were 593 ± 472, 81 ± 67, 558 ± 273 and 316 ± 213 ng/g dry weight (DW), respectively. Similarly, the average ∑₁₄PAH concentrations measured in the ambient air was found to be 15 ± 16 ng/m³. Generally, 4-, 5- and 6- ring PAHs were the dominant groups for all tree components, while 2- and 3-ring PAHs were predominant in the air samples. Ring distributions and molecular diagnosis ratios were employed to determine PAH sources in the sampling site. Petroleum and combustion-related sources were found to be important. The Pearson correlation coefficient was allowed to figure out the affinity between PAH levels in the sampling materials and meteorological factors. Temperature and mixing layer height were found to be effective factors on the concentrations. Atmospheric PAH levels were also predicted to employ a bark-air exchange model for determining the PAH movement direction. The predicted/measured ratios were above 1.0. This was probably due to utilizing the branch values rather than bark values in the model. Finally, the risk of cancer has been evaluated. The calculated cancer risks via inhalation were at low levels for adults and children.

Polychlorinated Naphthalenes across the Great Lakes: Lake Trout and Walleye Concentrations, Trends, and TEQ Assessment-2004-2018

Polychlorinated naphthalenes (PCNs) were measured in lake trout and walleye over the period 2004-2018, utilizing isotope dilution techniques with high-resolution gas chromatography/high-resolution mass spectrometry to assess concentrations and toxic equivalence (TEQ). An age-trend model was applied to mitigate the effect of a changing lake trout age structure. Most Great Lakes Fish Monitoring and Surveillance Program sampling sites demonstrated significant half-life and percent decreases for lake trout total PCNs and total TEQ over the 2004-2018 period, the exceptions being Lake Erie lake trout and walleye which illustrated increasing concentrations. Great Lakes total PCN concentrations ranged between 5701 and 100 pg/g ww, whereas total PCN TEQ concentrations ranged between 8.89 and 0.13 pg-TEQ/g ww. Based on the average number of chlorines per naphthalene, we determined that the overall lake trout and walleye PCN congener distribution has significantly shifted to a lower-chlorinated composition in the Great Lakes (5.33 to 4.48 Cl/CN) and has resulted in a substantial 59.1% reduction of the overall total PCN TEQ burden. A prominent PCN concentration trend breakpoint was observed in Lake Ontario lake trout over the 2012-2016 period likely associated with hazardous waste cleanups, channel dredging, and spoils disposal in the Detroit River and western-basin of Lake Erie.

Passive air sampling for semi-volatile organic chemicals

During passive air sampling, the amount of a chemical taken up in a sorbent from the air without the help of a pump is quantified and converted into an air concentration. In an equilibrium sampler, this conversion requires a thermodynamic parameter, the equilibrium sorption coefficient between gas-phase and sorbent. In a kinetic sampler, a time-averaged air concentration is obtained using a sampling rate, which is a kinetic parameter. Design requirements for kinetic and equilibrium sampling conflict with each other. The volatility of semi-volatile organic compounds (SVOCs) varies over five orders of magnitude, which implies that passive air samplers are inevitably kinetic samplers for less volatile SVOCs and equilibrium samplers for more volatile SVOCs. Therefore, most currently used passive sampler designs for SVOCs are a compromise that requires the consideration of both a thermodynamic and a kinetic parameter. Their quantitative interpretation depends on assumptions that are rarely fulfilled, and on input parameters, that are often only known with high uncertainty. Kinetic passive air sampling for SVOCs is also challenging because their typically very low atmospheric concentrations necessitate relatively high sampling rates that can only be achieved without the use of diffusive barriers. This in turn renders sampling rates dependent on wind conditions and therefore highly variable. Despite the overall high uncertainty arising from these challenges, passive air samplers for SVOCs have valuable roles to play in recording (i) spatial concentration variability at scales ranging from a few centimeters to tens of thousands of kilometers, (ii) long-term trends, (iii) air contamination in remote and inaccessible locations and (iv) indoor inhalation exposure. Going forward, thermal desorption of sorbents may lower the detection limits for some SVOCs to an extent that the use of diffusive barriers in the kinetic sampling of SVOCs becomes feasible, which is a prerequisite to decreasing the uncertainty of sampling rates. If the thermally stable sorbent additionally has a high sorptive capacity, it may be possible to design true kinetic samplers for most SVOCs. In the meantime, the passive air sampling community would benefit from being more transparent by rigorously quantifying and explicitly reporting uncertainty.

Atmospheric concentration, source identification, and health risk assessment of persistent organic pollutants (POPs) in two countries: Peru and Turkey

It is known that some persistent organic pollutants (POPs) are used worldwide, and these pollutants are dangerous for human health. However, there are still countries where measurements of these pollutants have not been adequately measured. Although many studies have been published for determining the concentrations of POPs in Turkey, there are limited studies in Latin American countries like Peru. For this reason, it is essential both to conduct a study in Peru and to compare the study with another country. This study is aimed at determining the atmospheric POPs such as polycyclic aromatic hydrocarbon (PAH), organochlorine pesticide (OCP), and polychlorinated biphenyl (PCB) concentrations using passive air samplers in Yurimaguas (Peru) and Bursa (Turkey). Molecular diagnosis ratios and ring distribution methods were used to determine the sources of PAHs. According to these methods, coal and biomass combustions were among the primary sources of PAHs in Peru, while petrogenic and petroleum were the primary sources of PAHs in Turkey. Then, α-HCH/γ-HCH and β-/(α+γ)-HCH ratios were used to determine the sources of OCPs. According to the α-HCH/γ-HCH ratios, the primary sources of OCPs in both countries were lindane. Similarly, according to β-/(α+γ)-HCH ratios, the HCHs have been historically used in Peru while they were recently utilized in Turkey. Finally, homologous group distributions were used to determine the sources of PCBs. Similar distributions of homologous groups were observed in the sampling sites in both countries. Also, the homologous group distributions obtained have been determined that industrial activities could be effective in the sampling areas in both countries. When the cancer risks that could occur via inhalation were evaluated, no significant cancer risk has been determined in both countries.

Environmental Exposure-Associated Human Health Risk of Dioxin Compounds in the Vicinity of a Municipal Solid Waste Incinerator in Shanghai, China

In order to assess environmental exposure-associated human health risk of dioxin compounds for the population in the vicinity of a municipal solid waste incinerator (MSWI) in Shanghai, the atmospheric samples (n = 24) and soils samples (n = 96) were collected and analyzed to obtain the concentration level, pollution characteristics and seasonal changes of dioxin compounds in environmental medias. The toxicity equivalent concentration range of 2,3,7,8-substituted polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) was 30.9-409 fg WHO-TEQ·m^-3 in atmosphere and 0.362-8.55 ng WHO-TEQ·kg^-1 in soil. The non-carcinogenic health risk and carcinogenic health risk from PCDD/Fs environmental exposure of people living in the vicinity of the MSWI in Shanghai were all within the allowable range of the US Environmental Protection Agency, which implied that the MSWI in Shanghai did not produce additional risk for the population living in its vicinity.

Compositional profiles, persistency and toxicity of polychlorinated naphthalene (PCN) congeners in edible cod liver products from 1972 to 2017

Edible cod liver products including cod liver oil and canned cod liver, sampled over the last five decades from the North Atlantic region, including the Baltic Sea were analysed for a set of persistent and toxicologically significant polychlorinated naphthalene (PCN) congeners with some of the highest relative potencies (dioxin-like toxicity) among PCNs. The targeted congeners showed a near-universality of occurrence in all samples apart from the most recent sample of cod liver oil which was assumed to be highly purified, as cod livers from the same period and location showed appreciable amounts of PCNs. The majority of dominant congeners in legacy technical PCN mixtures were absent or occurred in low concentrations, raising the possibility that congeners arising from combustion related sources may be acquiring a greater significance following the decline and elimination of PCN production. The apparent appreciation in the relative amounts of PCN#70 in the last three to four decades may provide support for this view. The PCN contribution to dioxin-like toxic equivalence (TEQ) that was estimated for these samples (range 1.2-15.9 pg TEQ g^-1) was significant in comparison to the EU regulated value of 1.75 pg TEQ g^-1 for dioxins in fish oils. Most of the TEQ was associated with PCNs 66/67, 64/68, 69 and 73. Although metabolic processes are likely to influence this distribution, the profile is a little different to that observed in the tissues of higher order animals where PCNs #66/67 and #73 may contribute approximately 90% to the summed TEQ.

PAH levels in a furniture-manufacturing city atmosphere

In this study, in order to determine atmospheric PAH concentrations in Inegol/Turkey, ambient air samples were collected from two different sites representing industrial and uncontrolled furniture manufacturers regions. Sampling campaign took place between December 2017 and November 2018. Air samples were collected using high volume air samplers (HVAS) and PAH concentrations were determined in both gas and particulate phases. The mean of the atmospheric PAH concentrations obtained in the gas phase in the furniture workshops (FW) and industrial district (ID) regions were 697.82 ± 637 ng/m³ and 772.92 ± 864.23 ng/m³, respectively. The concentrations in the particulate phase in the regions were 413.52 ± 430.23 ng/m³ and 342.40 ± 527.48 ng/m³, respectively. The average total (gas + particlulate phases) concentration of ∑₁₆PAH determined in the site of FW was 1111.34 ± 1045.24 ng/m³ while that was 772.92 ± 864.23 ng/m³ in ID. These values are over the ambient levels reported for urban sites wherein big industries exist around the world. Additionally, the average of particle phase percentage was 30% because of nearby combustion sources. The determination of possible sources of PAHs in the regions was performed using principal component analysis (PCA). PCA results showed that the main sources of pollutants of the regions are intertwined (combustion, traffic, industries). However, the most effective source is thought to be uncontrolled combustion of furniture wastes as fuel for residential heating. Health risks for the citizens were calculated for both regions and were found not to be at high-class risk.

Comparability of long-term temporal trends of POPs from co-located active and passive air monitoring networks in Europe

The comparability of data from active (ACT) and passive sampling (PAS) of persistent organic pollutants (POPs) in air is hindered by uncertainties related to the derivation of sampling rates and concentrations, as well as differences in the duration, volume and frequency of sampling. Although data from ACT have been used extensively in short-term PAS calibration studies, no attempts have been made to evaluate the comparability of long-term trends calculated from PAS to established ACT trends. This is crucial, as continuous long-term ACT is unfeasible in most regions of the world. To address these challenges, we calculated and compared trends for organochlorine pesticides (OCPs), polychlorinated biphenyls (PCBs) and polybrominated diphenyl ethers (PBDEs) at the six sites in Europe with at least 5 years of co-located ACT and PAS data (2012-2016): Birkenes, Košetice, Pallas, Råö, Stórhöfði and Zeppelin. Strong agreement of ACT and PAS trends was observed for most OCPs and PCBs. Apart from two PCBs at Stórhöfði, all pairs of ACT and PAS trends followed the same direction. However, differences in the magnitude, significance and confidence intervals of their slopes were observed for some compounds and were primarily attributed to the short duration of the PAS time series. Despite some limitations, our results suggest that the comparability of ACT and PAS POP trends will continue to improve with additional years of data. This study confirms the suitability of PAS for the calculation of long-term POP trends in air, and highlights the importance of continuous sampling at established monitoring sites with consistent analytical methods.

Preliminary investigation of polychlorinated dibenzo-p-dioxin and dibenzofuran, polychlorinated naphthalene, and dioxin-like polychlorinated biphenyl concentrations in ambient air in an industrial park at the northeastern edge of the Tibet-Qinghai Plateau, China

Ambient air samples collected in an industrial park at the northeastern edge of the Tibet-Qinghai Plateau (China) were analyzed for polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), polychlorinated naphthalenes (PCNs), and dioxin-like (dl) polychlorinated biphenyls (PCBs). The PCDD/F, PCN, and dl-PCB concentrations were 1.18-2.18, 21.9-75.1, and 0.49-0.90 pg/m³, respectively. The concentrations of these compounds were clearly higher than that observed at a remote site and were comparable with those found in ambient air in industrial areas in other locations. A principal component analysis indicated that emissions from local industrial sites (a secondary aluminum smelter, a cement kiln, and a lead-zinc smelter) at which thermal processes are performed were the sources of PCDD/Fs to the air. The combustion-related PCN congener profiles suggested that industrial thermal processes strongly affect PCN concentrations in ambient air at the industrial park. The results clearly indicated that the industrial park is a source of environmental PCDD/Fs and PCNs at the northeastern edge of the Tibet-Qinghai Plateau.

Using Polyurethane Foam-Based Passive Air Sampling Technique to Monitor Monosaccharides at a Regional Scale

Monosaccharides are important tracers of pollution aerosol from biomass burning. Air sampling of monosaccharides is often conducted using active samplers. However, applicability of sampling monosaccharides using polyurethane foam passive air samplers (PUF-PASs) has not been investigated, since passive air samplers are often applied to monitor semivolatile organic contaminants in large scale and remote area. Our study successfully collected atmospheric monosaccharides using PUF-PASs, providing a valuable tool for monosaccharides sampling. PUF-PAS sampling rates for individual monosaccharides were calibrated using an active sampler for 92 days, and were 1.1, 1.5, and 1.1 m³/d for levoglucosan, mannosan, and galactosan, respectively. Degradation of monosaccharides in PUF-PAS was demonstrated to be negligible by spike test of ¹³C-labeled levoglucosan. Furthermore, passive sampling was carried out at 11 sites in the Pearl River Delta of Southern China from January to April and July to September of 2015. Monosaccharide concentrations derived from PUF-PASs were comparable with the reported data obtained by active sampling, demonstrating that the PUF-PAS approach is valid for monosaccharides monitoring. On the basis of our approach, we found that there is a clear correlation between the monosaccharide concentrations and the MODIS fire activities during January-April.

Assessment of POPs in air from Spain using passive sampling from 2008 to 2015. Part II: Spatial and temporal observations of PCDD/Fs and dl-PCBs

Time series (2008-2015) of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and dioxin-like polychlorinated biphenyls (dl-PCBs) in ambient air from the Spanish Monitoring Program were analyzed. A total of 321 samples were collected seasonally each year in 5 urban and 7 background sites by means of passive air sampling. Air concentrations were higher at urban than background sites (urban vs. background concentration ranges): PCDD/Fs (26.9-1010 vs. 20.0-357 fg/m³), non-ortho PCBs (0.113-3.14 vs. 0.042-2.00 pg/m³) and mono-ortho PCBs (0.644-41.3 vs. 0.500-32.8 pg/m³). Results showed significant decreases from 2009 for non-ortho PCBs and PCDD/Fs as well as for WHO₂₀₀₆-TEQs. These declines were sharper, and sometimes only significant, in urban places resulting in converging levels at urban and background sites for these pollutants at the end of the study period. In contrast, mono-ortho PCBs did not show any significant variation but a steady flat temporal behavior in their concentrations, suggesting the existence of different sources between mono-ortho and non-ortho PCBs. Seasonality was observed for air burdens of all these POPs. PCDD/Fs were mostly measured at higher concentrations in colder than in hot seasons, and the opposite was true for dl-PCBs. Seasonal variations for PCDD/Fs appeared to be related to changes in their sources (e.g. domestic heating, open burning) rather than to temperature per se. In contrast, environmental temperature dependent factors (e.g. increased partitioning into the gas phase) drove seasonal variations in dl-PCBs instead of seasonal changes in their sources. Regarding spatial patterns, significant greater levels of PCDD/Fs and dl-PCBs were generally found in cities compared to background areas, pointing out the role of densely populated areas as sources for these pollutants in Spain. As proven by our results, long-term monitoring activities are essential to assess and understand temporal behaviors for these POPs, as well as to evaluate the achievement of Stockholm Convention objectives.

Chemical indicators of exposure to polychlorodibenzo-p-dioxins, polychlorodibenzofurans and polychlorobiphenyls in breast milk samples from mothers residing in Trento, Italy, and neighboring country municipalities

A human biomonitoring study was carried out in the province of Trento, northern Italy, on two groups of women residing in areas with presumably different levels of exposure to polychlorodibenzo-p-dioxins (PCDDs), polychlorodibenzofurans (PCDFs) and polychlorobiphenyls (PCBs). The aim was characterization of the possible impact of a steel plant and an urban environment on the internal doses of these contaminants. The areas investigated were the following: (i) the municipality of Borgo Valsugana, where a steel plant has been operating for the last 30 years, and (ii) the city of Trento. Ten women were enrolled from each area, and breast milk samples were collected from each woman. The amounts of PCDDs, PCDFs and PCBs were analyzed in all samples, and the data obtained were evaluated by descriptive and multivariate statistical approaches. For all samples, the concentrations observed were in the current acceptable concentration range observed in Europe. The descriptive statistics, however, clearly showed that some differences existed between the two groups: the PCDD, PCDF and DL-PCB concentrations were consistently higher in the Trento group of women living in the area surrounding the steel plant. Congener-profile analysis was carried out on both groups, and an appropriate multivariate approach, such as classical factor analysis (CFA), was used to investigate possible differential exposure sources. The application of this approach made it possible to show the quantitative and qualitative differences that characterized the two areas.

Multi-component determination of atmospheric semi-volatile organic compounds in soils and vegetation from Tarragona County, Catalonia, Spain

Tarragona County (Spain) is home to the most important chemical/petrochemical industrial complex in Southern Europe, which raises concerns about the presence and effects of the numerous environmental contaminants. In order to assess the levels and patterns of five classes of semi-volatile organic compounds (SVOCs) - polycyclic aromatic hydrocarbons (PAHs), synthetic musks (SMs), polychlorinated biphenyls (PCBs), brominated flame retardants (BFRs) and one organochlorine pesticide, hexachlorobenzene (HCB), 27 samples of soil and vegetation (Piptatherum L.) from different areas (petrochemical, chemical, urban/residential, and background) of Tarragona County were analysed. The results show that PAHs levels in soils ranged from 45.12 to 158.00ng/g and the urban areas presented the highest concentrations, mainly associated with the presence of a nearby highway and several roads with heavy traffic. PAHs levels in vegetation samples ranged from 42.13 to 80.08ng/g, where the greatest influence came from the urban and petrochemical areas. In the case of SMs, levels in soils and vegetation samples ranged from 5.42 to 10.04ng/g and from 4.08 to 17.94ng/g, respectively, and in both cases, background areas (at least 30km away from the main SVOCs emission sources) showed the highest levels, suggesting an influence of the personal care products derived from beach-related tourism in the coast. PCBs (from 6.62 to 14.07ng/g in soils; from 0.52 to 4.41ng/g in vegetation) prevailed in the chemical area in both matrices, probably associated with the presence of two sub-electrical stations located in the vicinities. In general terms, BFRs and HCB values recorded in soil and vegetation samples were quite similar between matrices and sampling areas.

An assessment of polyurethane foam passive samplers for atmospheric metals compared with active samplers

In this study, we conducted an assessment of polyurethane foam (PUF) passive sampling for metals combining active sampling. Remarkably, we found that the metals collected in the passive samples differed greatly from those collected in active samples. By composition, Cu and Ni accounted for significantly higher proportions in passive samples than in active samples, leading to significantly higher uptake rates of Cu and Ni. In assessing seasonal variation, metals in passive samples had higher concentrations in summer (excluding Heshan), which differed greatly from the pattern of active samples (winter > summer), indicating that the uptake rates of most metals were higher in summer than in winter. Overall, due to the stable passive uptake rates, we considered that PUF passive samplers can be applied to collect atmospheric metals. Additionally, we created a snapshot of the metal pollution in the Pearl River Delta using principal component analysis of PUF samples and their source apportionment.

Seasonal variations of PCDD/Fs congeners in air, soil and eggs from a Polish small-scale farm

The transfer of dioxin from the environment to the food is a problem in a consumers' health protection. The study aimed to determine the concentration of dioxins in free-range chicken eggs, air and soil samples, collected during 12 months on an individual small farm, located in Małopolska region, Poland. In the majority of analyzed eggs, the concentrations of dioxin exceeded several times the legal limit of 2.5 pg WHO-TEQ g-1fat. Seasonal changes in the PCDD/Fs congeners in egg, air and soil samples were studied. During the winter season, when the combustion processes of the solid fuel in domestic furnaces are intensive, the PM10 concentration in the Małopolska region exceeds the legal limit (50μg/m3) even eight times. In this period, eggs, air and soil samples showed a higher share of PCDFs with a specific contribution of 2,3,7,8-TCDF. During the summer months, in the egg, air and soil samples, the share of PCDDs is higher with dominant OCDD and 1,2,3,4,6,7,8-HpCDDs, showing the effect of other combustion processes such as grass utilization or burning plastic wastes in controlled fires. In August, the month of the highest average air temperature and lowest rainfall amount, the highest toxicity of PCDD/Fs in eggs (9.52pgWHO-TEQ g-1fat) was found. Due to the similarity of the shares of PCDD/Fs congeners in total WHO-TEQ value we can take into account the influence of toxicity of PCDD/Fs in the air and soil on the toxicity in the eggs.

Calibration and evaluation of PUF-PAS sampling rates across the Global Atmospheric Passive Sampling (GAPS) network

Passive air samplers equipped with polyurethane foam (PUF-PAS) are frequently used to measure persistent organic pollutants (POPs) in ambient air. Here we present and evaluate a method to determine sampling rates (R_S), and the effective sampling volume (V_eff), for gas-phase chemical compounds captured by a PUF-PAS sampler deployed anywhere in the world. The method uses a mathematical model that requires only publicly available hourly meteorological data, physical-chemical properties of the target compound, and the deployment dates. The predicted R_S is calibrated from sampling rates determined from 5 depuration compounds (¹³C PCB-9, ¹³C PCB-15, ¹³C PCB-32, PCB-30, and d₆-γ-HCH) injected in 82 samples from 24 sites deployed by the Global Atmospheric Passive Sampling (GAPS) network around the world. The dimensionless fitting parameter, gamma, was found to be constant at 0.267 when implementing the Integrated Surface Database (ISD) weather observations and 0.315 using the Modern Era Retrospective-Analysis for Research and Applications (MERRA) weather dataset. The model provided acceptable agreement between modelled and depuration determined sampling rates, with ¹³C PCB-9, ¹³C PCB-32, and d₆-γ-HCH having mean percent bias near zero (±6%) for both weather datasets (ISD and MERRA). The model provides inexpensive and reliable PUF-PAS gas-phase R_S and V_eff when depuration compounds produce unusual or suspect results and for sites where the use of depuration compounds is impractical, such as sites experiencing low average wind speeds, very cold temperatures, or remote locations.

High cancer risks by exposure to PCDD/Fs in the neighborhood of an Integrated Waste Management Facility

In 2014, we conducted a study aimed at screening the concentrations of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), polychlorinated biphenyls (PCBs) and various trace elements in air and soil samples collected in an urban area of Sant Adrià de Besòs (Barcelona, Spain) in the vicinity of an Integrated Waste Management Facility (IWMF). It consists of a mechanical-biological treatment plant (MBT) and an old municipal solid waste incinerator (MSWI). Human health risks for the population living in the area were also assessed. The most worrying result was the high cancer risks estimated for the area (2.5×10^-6). In March 2017, we have carried out a new survey to check if the authorities had taken the necessary and urgent measures to reduce the environmental concentrations of PCDD/Fs -and the human health risks- until acceptable levels. Although the concentrations of PCDD/Fs in soils are currently lower (mean value: 1.66 vs. 3.6ng WHO-TEQ/kg in 2014), they are still are notably higher than those found near other MSWIs of Catalonia. In turn, the levels of PCDD/Fs in air are even higher than in 2014 (mean value: 0.044 vs. 0.026pgWHO-TEQ/m³ in 2014), being also the highest detected in similar zones of Catalonia. The current cancer risk due to PCDD/F exposure for the residents in the neighborhood of the IWMF is 2.3×10^-6, a worrying fact as the 10^-6 threshold continues to be exceeded.

Occurrence, Loading, and Exposure of Atmospheric Particle-Bound POPs at the African and European Edges of the Western Mediterranean Sea

A comparative study for 62 toxic chemicals based on the simultaneous monthly collection of aerosol samples during 2015-2016 in two coastal cities at both the African (Bizerte, Tunisia) and European (Marseille, France) edges of the Western Mediterranean basin is presented. Legacy polychlorinated biphenyls (∑₁₈PCBs) and polychlorinated dibenzo-p-dioxins and dibenzofurans (∑₁₇PCDD/Fs) show generally higher median levels at the African edge (2.1 and 0.2 pg m^-3, respectively) compared to the European coastal site (1.0 and 0.08 pg m^-3, respectively). Contrarily, the "emerging" polybrominated diphenyl ethers' (∑₂₇PBDEs) median concentrations were higher in Marseille (∼9.0 pg m^-3) compared to Bizerte (∼6.0 pg m^-3). Different past usages and current emission patterns were found at both edges of the Western Mediterranean, most probably linked to the respective different regulatory frameworks for toxic chemicals. Our results indicate that the total organic carbon (TOC) and/or the elemental carbon (EC) contents in the atmospheric aerosol may have a stronger effect than the total suspended particle (TSP) content as a whole on the spatial-temporal variability and the long-range atmospheric transport potential of the studied POPs. A "jumping" of the PBDE local atmospheric stocks from the Northwestern European Mediterranean edge to the Northwestern African coast seems to be possible under favorable conditions at present. While a higher PBDE median loading is estimated for the Marseille area (∼550 ng m^-2 y^-1) compared to Bizerte (∼400 ng m^-2 y^-1), the median PCB and PCDD/F dry deposition fluxes were higher at the African site, resulting in a 3-fold higher toxic equivalent (TEQ) loading of dioxin-like pollutants (400 pg TEQ m^-2 y^-1) compared to Marseille (∼140 pg TEQ m^-2 y^-1), with potential implications for aquatic organisms. However, the inhalation exposure assessment points to a minimum risk for human health at both sites.

Monitoring PAHs in the petrochemical area of Tarragona County, Spain: comparing passive air samplers with lichen transplants

The levels of 16 polycyclic aromatic hydrocarbons (PAHs) were determined in 8 passive air samples (PAS) and 6 lichen transplants (Ramalina fastigiata) deployed for a period of 2 months in different zones of Tarragona County (Catalonia, Spain), an area with an important number of chemical and petrochemical industries. The accumulated amount of the sum of the 16 PAHs ranged between 1363 to 7866 ng/sample in air samples. The highest concentration was found in the neighborhood of Puigdelfí (village of Perafort), in the vicinity of a big oil refinery and well under the potential influence of the petrochemical emissions. In lichen samples, the sum of the 16 PAHs ranged between 247 and 841 ng/g (dry weight), being the greatest value also observed in Puigdelfí. Data on the levels and profiles of PAHs in both passive monitoring methods were compared. A significant positive linear correlation was found between the concentrations of low molecular weight PAHs in lichens and the amounts accumulated in passive air samples (R = 0.827, P < 0.05), being especially significant the correlation of 4-ring PAHs (R = 0.941, P < 0.05). These results strongly suggest that lichens can be used to monitor gas-phase PAHs, providing data that can be quantitatively translated into equivalents for air.

Occurrence and seasonal distribution of polycyclic aromatic hydrocarbons and legacy and current-use pesticides in air from a Mediterranean coastal lagoon (Mar Menor, SE Spain)

The occurrence and seasonal distribution of polycyclic aromatic hydrocarbons (PAHs) and legacy and current-use pesticides (CUPs) in air were characterized around the Mar Menor lagoon using both active and passive sampling devices. The seasonal distribution of these pollutants was determined at 6 points using passive samplers. Passive sampler sampling rates were estimated for all detected analytes using an active sampler, considering preferentially winter data, due to probable losses in active sampling during summer (high temperatures and solar irradiation). The presence of 28 compounds (14 CUPs, 11 PAHs and 3 organochlorinated pesticides) were detected in air by polyurethane passive sampling. The most commonly detected contaminants (>95% of samples) in air were chlorpyrifos, chlorpyrifos-methyl and phenanthrene. The maximum concentrations corresponded to phenanthrene (6000 pg m^-3) and chlorpyrifos (4900 pg m^-3). The distribution of contaminants was spatially and seasonally heterogeneous. The highest concentrations of PAHs were found close to the airport, while the highest concentrations of pesticides were found in the influence area of agricultural fields (western stations). PAH and herbicide concentrations were higher in winter than in the other seasons, although some insecticides such as chlorpyrifos were more abundant in autumn. The presence of PAHs and legacy and current-use pesticides in air confirmed their transference potential to marine coastal areas such as the Mar Menor lagoon.

Airborne PCDD/F profiles in rural and urban areas of Buenos Aires Province, Argentina

Passive air samplers were deployed in 18 rural and urban locations in the densely populated Buenos Aires district to investigate airborne polychlorinated dibenzo-p-dioxin and polychlorinated-dibenzofuran (PCDD/Fs) profiles, sources and spatial patterns. Atmospheric concentrations reported as total toxic equivalents (TEQs), 2378-substituted (∑₁₇PCDD/F) and 4-8 homologous groups (∑_4-8PCDD/F) were highly variable and significantly correlated to urban scale. The rural average (3.0±2.7fgTEQm^-3) was thirty times less than metropolitan values (90±51fgTEQm^-3), with urban cluster (5.4±4.0fgTEQm^-3) and urbanized area (33±50fgTEQm^-3) in an intermediate position. A rural outlier exhibited the highest TEQ values (295-296fgTEQm^-3) suggesting a local source. Principal component analyses (PCA) performed for ∑₁₇PCDD/F and ∑_4-8PCDD/F to identify source contributions showed more significant results for homologue groups compared to 17 congeners (83 and 45% of total variability explained, respectively) pointing to dominant diesel emissions enriched in TeCDF in rural areas, and open burning and industrial sources characterized by TeCDD, PeCDD contributing most in urbanized and metropolitan areas. Homologue group PCA also performed better clustering samples according to sources and TEQ concentrations. The PCDD/Fs profile of the rural outlier dominated by HxCDF and HpCDD/F showed a typical municipal incineration signature confirming the presence of local source.

PCDD, PCDF, dl-PCB and organochlorine pesticides monitoring in São Paulo City using passive air sampler as part of the Global Monitoring Plan

The persistent organic pollutants (POPs), such as organochlorine pesticides and PCBs, are ordinarily monitored in the aquatic environment or in soil in the environmental quality monitoring programs in São Paulo, Brazil. One of the core matrices proposed in the POPs Global Monitoring Plan (GMP) from the Stockholm Convention list is the ambient air, which is not a usual matrix for POPs monitoring in the country. In this study POP levels were evaluated in the air samples from an urban site in São Paulo City over five years, starting in 2010 as a capacity building project for Latin America and the Caribbean region for POP monitoring in ambient air using passive samplers. Furthermore, after the end of the Project in 2012, the monitoring continued in the same sampling site as means to improving the analytical capacity building and contribute to the GMP data. The POPs monitored were 17 congeners of 2,3,7,8 chloro-substituted PCDDs and PCDFs, dioxin-like PCBs, indicator PCBs, organochlorine pesticides and toxaphene. The results show a slight decrease in PCDD/F, dl-PCBs and indicator PCBs levels along the five years. The organochlorine pesticide endosulfan was present at its highest concentration at the beginning of the monitoring period, but it was below detection level in the last year of the monitoring. Some other organochlorine pesticides were detected close to or below quantitation limits. The compounds identified were dieldrin, chlordane, α-HCH, γ-HCH, heptachlor, heptachlor epoxide, hexachlorobenzene and DDTs. Toxaphene congeners were not detected. These results have confirmed the efficacy of passive sampling for POP monitoring and the capacity building for POP analysis and monitoring was established. However more needs to be done, including expansion of sampling sites, new POPs and studies on sampling rates to be considered in calculating the concentration of POPs in ambient air using a passive sampler.

Environmental variation of PCDD/Fs and dl-PCBs in two tropical Andean Colombian cities using passive samplers

Passive air-sampling data of polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs) and dioxin-like polychlorinated biphenyls (dl-PCBs) taken in Manizales (a medium-sized city) and Bogotá (a megacity), Colombia, were analyzed in order to identify potential sources of pollution and the possible influence of meteorological variables like temperature and precipitation. The results indicate important differences in levels of PCDD/Fs and dl-PCBs between Bogotá and Manizales, attributed to differences in site characteristics and potential local/regional sources. Higher PCDD/Fs concentrations were observed in Bogotá (373fg/m(3)) compared to those observed in Manizales, with mean levels ranging from 64fg/m(3) in a residential zone to 151fg/m(3) around a vehicular-influenced area. Higher dl-PCBs concentrations were observed in the industrial area of Manizales compared to those observed in Bogotá, with mean levels of 6668fg/m(3) and 4388fg/m(3) respectively. In terms of PCDD/Fs congener distribution, there was a predominance of octachlorodibenzodioxin (OCDD) followed by 1,2,3,4,6,7.8-heptachlorodibenzofuran (HpCDF) congeners, with both cities showing higher levels in zones of high vehicular activity. Industrial influence was most evident in dl-PCB levels. In comparison to the mean levels of dl-PCB congeners obtained in the vehicular zones of Bogotá and Manizales, the industrially influenced sampling stations showed higher concentrations of dl-PCB congeners. Passive sampling results suggested that congener concentration profiles are characteristic of their different emission sources, and can be used to distinguish between their industrial or vehicular origins.

Towards the implementation of the Stockholm Convention in Spain: Five-year monitoring (2008-2013) of POPs in air based on passive sampling

Within the framework of the Spanish monitoring program, this study reports on air concentration of DDTs, HCB, HCHs, NDL-PCBs, DL-PCBs, PCDD/Fs and PBDEs measured during the five-year sampling period 2008-2013. Spanish coastal remote and urban locations were studied using PUF disk passive air samplers which were deployed and collected every three months. Despite the wide range of concentrations measured for most contaminants, a common pattern of relative abundance (median values): NDL-PCBs (36.6 pg/m(3)) > HCB (24.8 pg/m(3)) ≈ HCHs (17.9 pg/m(3)) ≈ DDTs (16.6 pg/m(3)) > PBDEs (3.65 pg/m(3)) > DL-PCBs (2.99 pg/m(3)) >> PCDD/Fs (0.060 pg/m(3)) was found fairly consistent across most seasons and locations. Nevertheless, important variations in yearly concentrations were measured for different POPs. In general, higher levels of DDTs, HCHs, NDL-PCBs, DL-PCBs and PCDD/Fs were found in urban sites highlighting important differences between remote and urban sampling locations for most target contaminants. Greater concentrations of the banned organochlorine pesticides in urban locations suggested the existence of unexpected pointed sources that need to be further investigated and characterized. The limited dataset collected thus far rendered no clear temporal trends for most study target compounds, which emphasizes the necessity of the Spanish monitoring program future maintenance in time.

Time trends of persistent organic pollutants in spanish air

Passive air samplers consisting of polyurethane foam (PUF) disks were deployed in seven remote points and four urban locations to assess levels of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), polychlorinated biphenyls (PCBs), polybrominated diphenyl ethers (PBDEs), and some organochlorine pesticides including: 1,1'-(2,2,2-trichloroethane-1,1-diyl)bis(4-chlorobenzene) (DDT) and their metabolites (1,1-bis-(4-chlorophenyl)-2,2-dichloroethene (DDE) and 1-chloro-4-[2,2-dichloro-1-(4-chlorophenyl)ethyl]benzene (DDD)), hexaclorobenzene (HCB) and hexachlorocyclohexanes (HCHs), in the Spanish ambient air. Results revealed HCB (49 pg m(-3); median) as the major pollutant, followed in decreasing order by HCHs (21 pg m(-3)), ∑DDT/E/Ds (20 pg m(-3)), PCBs (20 pg m(-3)), PBDEs (3.3 pg m(-3)) and PCDD/Fs (0.04 pg m(-3)), when urban and remote locations are evaluated together. Urban areas presented statistically significant (p < 0.05, Mann-Whitney U test) higher levels for all families studied, except for HCB, compared to remote locations revealing anthropogenic activities as potential sources for these chemicals. On the contrary, HCB concentrations seem to reflect background levels. Interestingly, results reveal a decreasing trend for PCBs, PBDEs and DDTs levels in remote areas, while this behaviour is only statistically significant in the case of the former chemicals in urban locations. The present study is framed in the Spanish air monitoring plan and represents the first complete analysis related to POP presence in Spanish air coming from inner sites.

A review of polychlorinated biphenyls (PCBs) pollution in indoor air environment

Polychlorinated biphenyls (PCBs) were widely used in industrial production due to the unique physical and chemical properties. As a kind of persistent organic pollutants, the PCBs would lead to environment pollution and cause serious problems for human health. Thus, they have been banned since the 1980s due to the environment pollution in the past years. Indoor air is the most direct and important environment medium to human beings; thus, the PCBs pollution research in indoor air is important for the protection of human health. This paper introduces the industrial application and potential harm of PCBs, summarizes the sampling, extracting, and analytical methods of environment monitoring, and compares the indoor air levels of urban areas with those of industrial areas in different countries according to various reports. This paper can provide a basic summary for PCBs pollution control in the indoor air environment.

IMPLICATIONS

The review of PCBs pollution in indoor air in China is still limited. In this paper, we introduce the industrial application and potential harm of PCBs, summarize the sampling, extracting, and analytical methods of environment monitoring, and compare the indoor air levels of urban areas with industrial areas in different countries according to various reports.

Computational fluid dynamics (CFD) simulation of a newly designed passive particle sampler

In this work a series of computational fluid dynamics (CFD) simulations were performed to predict the deposition of particles on a newly designed passive dry deposition (Pas-DD) sampler. The sampler uses a parallel plate design and a conventional polyurethane foam (PUF) disk as the deposition surface. The deposition of particles with sizes between 0.5 and 10 μm was investigated for two different geometries of the Pas-DD sampler for different wind speeds and various angles of attack. To evaluate the mean flow field, the k-ɛ turbulence model was used and turbulent fluctuating velocities were generated using the discrete random walk (DRW) model. The CFD software ANSYS-FLUENT was used for performing the numerical simulations. It was found that the deposition velocity increased with particle size or wind speed. The modeled deposition velocities were in general agreement with the experimental measurements and they increased when flow entered the sampler with a non-zero angle of attack. The particle-size dependent deposition velocity was also dependent on the geometry of the leading edge of the sampler; deposition velocities were more dependent on particle size and wind speeds for the sampler without the bend in the leading edge of the deposition plate, compared to a flat plate design. Foam roughness was also found to have a small impact on particle deposition.

Seasonal and spatial distributions of atmospheric polychlorinated naphthalenes in Shanghai, China

Air samples were collected in Shanghai during summer and winter 2013, and the gas and particulate concentrations of polychlorinated naphthalenes (PCNs) were measured. All 75 congeners were quantified and the corresponding toxic equivalents (TEQs) were calculated. PCN concentrations were higher in summer than winter, at 8.22-102 pg/m(3) (average of 61.3 pg/m(3)) in summer and 16.5-61.1 pg/m(3) (average of 37.7 pg/m(3)) in winter. Their seasonal TEQ values were in contrast, at 1.35-7.31 fg/m(3) (average of 3.84 fg/m(3)) in summer and 4.08-23.3 fg/m(3) (average of 8.80 fg/m(3)) in winter, because of the seasonal change in congener profiles. Tri-CNs were the predominant homologs in both the summer and winter samples. However, the major congeners in summer were PCNs containing less chlorine, but these decreased over winter. Air mass back trajectories suggested that wind direction over various sites was similar in the summer and winter seasons, yet there were clear seasonal variations in atmospheric PCN concentrations. Ratios of several characteristic congeners were calculated and the results indicated that the ratios varied only to a limited extent with PCN emissions profile from industrial thermal sources, but varied strongly with profiles of technical PCN and PCN contaminants in polychlorinated biphenyl mixtures. The results of principal component analysis suggest that local industrial thermal emissions (thermal processes containing waste incineration and secondary metal smelting processes) still play a considerable role in influencing the atmospheric PCNs in Shanghai.

Seasonal variations in concentrations, distributions, and air-soil exchange fluxes of dioxin-like polychlorinated biphenyls in Shanghai, China

Dioxin-like polychlorinated biphenyl (dl-PCB) concentrations in ambient air and soil in Shanghai, China, were measured to allow seasonal and spatial differences in the dl-PCB concentrations, profiles, distributions, fugacity fractions, and air-soil fluxes to be determined. The toxic equivalent (TEQ) DL-PCB concentrations in the air were higher in summer (mean 9.46 fg m(-3), range 1.32-26.3 fg m(-3)) than in winter (mean 4.57 fg m(-3), range 1.55-10.9 fg m(-3)). The DL-PCB concentrations in air were different in different areas, and the concentrations decreased in the order industrial areas > commercial and residential areas > suburban areas > rural area. The mean DL-PCB concentration in soil was 0.25 pg TEQ g(-1) dry weight (dw) and the range was 0.05-0.90 pg TEQ g(-1) dw. The highest DL-PCB concentration in soil was found in a sample from a commercial/residential area. The DL-PCB fluxes were negative (-216 pg m(-2) h(-1) in summer and -41.1 pg m(-2) h(-1) in winter), and the fugacity fractions were below 0.5, indicating that dl-PCBs in Shanghai are deposited from the air to the soil in all seasons. The net fluxes were higher in summer than in winter, and the deposition fluxes were higher in industrial areas than in other areas in both summer and winter.

Spatial Distribution of Atmospheric PCBs in Zurich, Switzerland: Do Joint Sealants Still Matter?

Passive air samplers were deployed at 23 sites across the city of Zurich, Switzerland to investigate the spatial distribution of polychlorinated biphenyls (PCBs) in air. Concentrations of the six indicator PCBs (iPCBs) in air ranged from 54 to 3160 pg·m(-3) in the two sampling campaigns (spring 2011 and spring 2013). Measurements at two sampling sites were significantly higher than the median in both years, because of the proximity to primary PCB sources. Concentrations at most other stations were in a narrow range, suggesting that atmospheric PCB concentrations in Zurich are mainly caused by a high number of rather small sources. A correlation of iPCB concentrations in air with the number of buildings constructed between 1955 and 1975 in the surrounding areas of the sampling sites was observed. This demonstrates that PCB-containing building materials, such as joint sealants, influence PCB levels in urban air. Additionally, atmospheric iPCB concentrations were measured in the surrounding of a housing complex with PCB-contaminated joint sealants. Using a Gaussian diffusion model, annual iPCB emissions of 110-190 g were calculated for this housing complex. This appreciable amount released by a single building points out that more efforts are required to further eliminate remaining PCB stocks.

Passive air sampling for determining the levels of ambient PCDD/Fs and their seasonal and spatial variations and inhalation risk in Shanghai, China

The seasonal and spatial variations, compositional profiles, and possible sources of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) in ambient air samples in Shanghai of China were investigated by passive air samplers, and the potential inhalation risks posed by these chemicals were evaluated. The following results were obtained: (1) The World Health Organization (WHO) toxic equivalency (TEQ) values for PCDD/Fs were in the range of 10.8-259 fg m(-3) (mean 63.4 fg m(-3)) in summer and 24.1-154 fg m(-3) (mean 83.4 fg m(-3)) in winter. Atmospheric PCDD/F levels were in the following order: industrial areas > commercial and residential areas > rural areas. (2) 2,3,4,7,8-PeCDF (24 %), 2,3,7,8-TeCDD (16 %), 1,2,3,7,8-PeCDD (13 %), and 2,3,7,8-TeCDF (12 %) were the predominant contributors to the TEQ of PCDD/Fs. (3) There was a slight seasonal trend with higher TEQ values in winter than in summer, which could be related to seasonal variations in the dispersion of PCDD/Fs in ambient air. (4) The children's daily intake was at the lower end of the range for the tolerable daily intake of PCDD/Fs recommended by WHO, which indicates that the inhalation risk of PCDD/Fs for local residents in Shanghai is relatively low.

Health risks for the population living in the vicinity of an Integrated Waste Management Facility: screening environmental pollutants

We performed a screening investigation to assess the human health risks of the Integrated Waste Management Facility (IWMF: mechanical-biological treatment (MBT) plant plus municipal solid waste incinerator (MSWI); Ecoparc-3) of Barcelona (Spain). Air concentrations of pollutants potentially released by the MBT plant (VOCs and bioaerosols) and the MSWI (trace elements, PCDD/Fs and PCBs) were determined. Trace elements, PCDD/Fs and PCBs were also analyzed in soil samples. The concentrations of trace elements and bioaerosols were similar to those previously reported in other areas of similar characteristics, while formaldehyde was the predominant VOC. Interestingly, PCDD/F concentrations in soil and air were the highest ever reported near a MSWI in Catalonia, being maximum concentrations 10.8 ng WHO-TEQ/kg and 41.3 fg WHO-TEQ/m(3), respectively. In addition, there has not been any reduction in soils, even after the closure of a power plant located adjacently. Human health risks of PCDD/F exposure in the closest urban nucleus located downwind the MSWI are up to 10-times higher than those nearby other MSWIs in Catalonia. Although results must be considered as very preliminary, they are a serious warning for local authorities. We strongly recommend to conduct additional studies to confirm these findings and, if necessary, to implement measures to urgently mitigate the impact of the MSWI on the surrounding environment. We must also state the tremendous importance of an individual evaluation of MSWIs, rather than generalizing their environmental and health risks.

Assessing polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans in air across Latin American countries using polyurethane foam disk passive air samplers

A passive air sampling network has been established to investigate polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) at Global Atmospheric Passive Sampling (GAPS) sites and six additional sites in the Group of Latin American and Caribbean Countries (GRULAC) region. The air sampling network covers background, agricultural, rural, and urban sites. Samples have been collected over four consecutive periods of 6 months, which started in January 2011 [period 1 (January to June 2011), period 2 (July to December 2011), period 3 (January to June 2012), and period 4 (July 2012 to January 2013)]. Results show that (i) the GAPS passive samplers (PUF disk type) and analytical methodology are adequate for measuring PCDD/F burdens in air and (ii) PCDD/F concentrations in air across the GRULAC region are widely variable by almost 2 orders of magnitude. The highest concentrations in air of Σ4-8PCDD/Fs were found at the urban site São Luis (Brazil, UR) (i.e., 2560 fg/m3) followed by the sites in São Paulo (Brazil, UR), Mendoza (Argentina, RU), and Sonora (Mexico, AG) with values of 1690, 1660, and 1610 fg/m3, respectively. Very low concentrations of PCDD/Fs in air were observed at the background site Tapanti (Costa Rica, BA), 10.8 fg/m3. This variability is attributed to differences in site characteristics and potential local/regional sources as well as meteorological influences. The measurements of PCDD/Fs in air agree well with model-predicted concentrations performed using the Global EMEP Multimedia Modeling System (GLEMOS) and emission scenario constructed on the basis of the UNEP Stockholm Convention inventory of dioxin and furan emissions.

Emissions of polychlorinated biphenyls in Switzerland: a combination of long-term measurements and modeling

Ambient air concentrations of polychlorinated biphenyls (PCBs) in Zurich, Switzerland, are reported for the years 2011-2013. These measurements reveal a distinct seasonal trend with PCB concentrations in air during the summer that were three to five times higher than in the winter. We used a long-term dynamic multimedia model to analyze the seasonal trend and to back-calculate urban emissions of PCBs. In contrast to previous short-term studies that considered time periods of several days to months to extrapolate annual emissions, the use of long-term field data and the corresponding model reduces the uncertainty in these extrapolations. Comparison with measured PCB concentrations in air shows that our model is able to reproduce seasonal trends of the six indicator PCBs (iPCBs). The good agreement of the model results with measurements over a time period of three years provides confidence in model outputs and allows us to estimate the total annual PCB emissions of Zurich (86 μg capita(-1) d(-1)). The resulting summer emissions are nine times higher than emissions during winter. Interestingly, this factor corresponds to the expected increase in PCB volatilization due to the effect of temperature on vapor pressure. This finding implies that PCBs in Zurich are probably released mainly by volatilization from sources that are directly exposed to ambient air temperature (i.e., outdoor sources). The derived emissions are in accordance with previous studies performed at the same location and are also in agreement with an existing emission inventory.

Current challenges in air sampling of semivolatile organic contaminants: sampling artifacts and their influence on data comparability

With current science and policy needs, more attention is being given to expanding and improving air sampling of semivolatile organic contaminants (SVOCs). However, a wide range of techniques and configurations are currently used (active and passive samplers, different deployment times, different sorbents, etc.) and as the SVOC community looks to assess air measurements on a global scale, questions of comparability arise. We review current air sampling techniques, with a focus on sampling artifacts that can lead to uncertainties or biases in reported concentrations, in particular breakthrough, degradation, meteorological influences, and assumptions regarding passive sampling. From this assessment, we estimate the bias introduced for SVOC concentrations from all factors. Due to the effects of breakthrough, degradation, particle fractions and sampler uptake periods, some current passive and active sampler configurations may underestimate certain SVOCs by 30-95%. We then recommend future study design, appropriateness of sampler types for different study goals, and finally, how the SVOC community should move forward in both research and monitoring to best achieve comparability and consistency in air measurements.

Spatial and seasonal distributions of polychlorinated dibenzo-p-dioxins and dibenzofurans and polychlorinated biphenyls around a municipal solid waste incinerator, determined using polyurethane foam passive air samplers

Twenty-six ambient air samples were collected around a municipal solid waste incinerator (MSWI) in the summer and winter using polyurethane foam passive air samplers, and analyzed to assess the spatial and seasonal distributions of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and polychlorinated biphenyls (PCBs). Three stack gas samples were also collected and analyzed to determine PCDD/F (971 pg m(-3) in average) and PCB (2,671 pg m(-3) in average) emissions from the MSWI and to help identify the sources of the pollutants in the ambient air. The total PCDD/F concentrations in the ambient air samples were lower in the summer (472-1,223 fg m(-3)) than the winter (561-3913 fg m(-3)). In contrast, the atmospheric total PCB concentrations were higher in the summer (716-4,902 fg m(-3)) than the winter (489-2,298 fg m(-3)). Principal component analysis showed that, besides emissions from the MSWI, the domestic burning of coal and wood also contributed to the presence of PCDD/Fs and PCBs in the ambient air. The PCDD/F and PCB spatial distributions were analyzed using ordinary Kriging Interpolation and limited effect was found to be caused by emissions from the MSWI. Higher PCDD/F and PCB concentrations were observed downwind of the MSWI than in the other directions, but the highest concentrations were not to be found in the direction with the greatest wind frequency which might be caused by emissions from domestic coal and wood burning. We used a systemic method including sampling and data analysis method which can provide pioneering information for characterizing risks and assessing uncertainty of PCDD/Fs and PCBs in the ambient air around MSWIs in China.