A critical review on advanced oxidation processes for the removal of trace organic contaminants: A voyage from individual to integrated processes

The recent advances of MnFe2O4-based nanoparticles in environmental application: A review

The manganese ferrite (MnFe2O4)-based nanoparticles showed a substantial potential to remediate the various pollutants in environmental application due to low cost, simple magnetic separation and high removal capacity. Herein, the functionalization of various MnFe2O4-based nanoparticles was briefly summarized; Then the recent advances concerning the removal of pollutants (i.e., organics, heavy metals and antibacterial activity) on different MnFe2O4-based nanoparticles were reviewed in details. The reactivity of MnFe2O4-based nanoparticles was significantly influenced by environmental factors. It is demonstrated that interaction mechanism of various pollutants on magnetic MnFe2O4-based nanoparticles included degradation, adsorption, coordination, redox and precipitation. Finally, the current problems and future perspective of MnFe2O4-based nanoparticles were proposed. The highlight of this review is to compare the removal performance of MnFe2O4-based nanoparticles with the different hybrids. This review is crucial for the application of MnFe2O4-based nanoparticles in the environmental remediation.

Sustainable urea treatment by environmental-friendly and highly hydrophilic vesicle-like iron phosphate-based carbon

Despite the versatile potential applications of urea, its unfavorable characteristics for conventional treatment methods hinder its utilization. Therefore, this study developed vesicle-like iron phosphate-based carbon (IP@C400) as a breakthrough urea removal and recovery material for a wide range of urea-containing sources. IP@C400 rapidly exhibited an exceptional capacity (2242 mg/g in 1 h) across a wide range of pH, even in synthetic hemodialysis wastewater with high urea concentrations and diverse co-existing components, compared with the 60 prominent adsorbents. The adsorption process followed dual Pseudo-kinetic, Langmuir-isotherm models with the involvement of primary robust physical (i.e., H-bonding and electrostatic interaction) and chemical mechanisms (i.e., hydrolysis). Remarkably, IP@C400 can maintain high urea removal (90 %) or recovery efficiency (95 %) even after 10 cycles with minimal leakages of Fe and P (far below WHO and EUWFD standards)-a significant improvement over disposable options. IP@C400 could also perform efficiently on batch and a new approach integrating with a naturally accessible material based on the fixed-bed column using low-range urea realistic samples, achieving 65.2 L water over 10 cycles with undetected urea, neutral pH, and well-aligned water safety standards with a minimal adsorbent dose (0.1 g.L-1) and economical cost ($0.05 L-1). Lastly, its environmentally friendly nature, which contains essential nutrients for plant growth, further enhances its recyclability after release. Thus, IP@C400 offers a solution to environmental sustainability and the urgent ultrapure water issue that industries are facing.

Enhanced degradation of enoxacin using ferrihydrite-catalyzed heterogeneous photo-Fenton process

The ferrihydrite-catalyzed heterogeneous photo-Fenton reaction shows great potential for environmental remediation of fluoroquinolone (FQs) antibiotics. The degradation of enoxacin, a model of FQ antibiotics, was studied by a batch experiment and theoretical calculation. The results revealed that the degradation efficiency of enoxacin reached 89.7% at pH 3. The hydroxyl radical (∙OH) had a significant impact on the degradation process, with a cumulative concentration of 43.9 μmol L-1 at pH 3. Photogenerated holes and electrons participated in the generation of ∙OH. Eleven degradation products of enoxacin were identified, with the main degradation pathways being defluorination, quinolone ring and piperazine ring cleavage and oxidation. These findings indicate that the ferrihydrite-catalyzed photo-Fenton process is a valid way for treating water contaminated with FQ antibiotics.

Enhanced inactivation of Escherichia coli through hydrogen peroxide decomposition assisted by nanoscale cupric oxide-decorated activated carbon

In this study, nanoscale cupric oxide-decorated activated carbon (nCuO@AC) was synthesized by impregnation-calcination and employed to assist the decomposition of H2O2 for effective sterilization with Escherichia coli as target bacteria. Characteristic technologies demonstrated that copper oxide particles of 50-100 nm were uniformly distributed on AC surface. Owing to electron transfer from hydroxyl and aldehyde to CuO on AC, surface-bonded Cu(II) was partially reduced to Cu(I) in the nCuO matrix. The resultant Cu(I) expedited the decomposition of H2O2 and converted it into ·OH radicals which were identified by quenching experiment and electron paramagnetic resonance test. Due to oxidation attack of generated ·OH, the nCuO@AC-H2O2 system achieved a much higher inactivation rate of 6.0 log within 30 min as compared to those of 2.1 and 1.3 log in the nCuO@AC and nCuO-H2O2 systems. It also exhibited excellent pH adaptability and high inactivation efficiency under neutral conditions. After four cycles, the nCuO@AC-H2O2 system could still inactivate 5.5 log bacteria, indicating excellent stability and reusability of nCuO@AC. Spent nCuO@AC could be regenerated by eluting surficial copper oxides with hydrochloric acid, and re-coating nCuO particles through impregnation-calcination with a regeneration rate of 96.6%. Our results demonstrated that nCuO@AC was an efficient and prospective catalyst to assist the decomposition of H2O2 for effective inactivation of bacteria in water.

Machine learning modeling of fluorescence spectral data for prediction of trace organic contaminant removal during UV/H2O2 treatment of wastewater

Dynamic feedback of the removal performance of trace organic contaminants (TrOCs) is essential towards economical advanced oxidation processes (AOPs), whereas the corresponding quick-response feedback methods have long been desired. Herein, machine learning (ML) multi-target regression random forest (MORF) models were developed based on the fluorescence spectra to predict the removal of TrOCs during UV/H2O2 treatment of municipal secondary effluent as a typical AOP. The predictive performance of the developed MORF model (R2 = 0.83-0.95) exhibited higher accuracy over the traditional linear regression models with R2 increased by ∼0.15. Furthermore, through feature importance analysis, the spectral regions of high importance were identified for different groups of TrOCs, thus enabling faster data acquisition due to remarkably reduced size of required fluorescence spectral scanning region. Specifically, the fluorescence regions Ex(235-275 nm)/Em(325-400 nm) and Ex(240-360 nm)/Em(325-450 nm) were found highly correlated with the removal of the TrOCs susceptible to both photodegradation and •OH degradation and those primarily subject to •OH degradation, respectively. In addition, the spectral regions of high importance were also individually identified for the investigated TrOCs during the AOP. Through providing an efficient ML-based feedback method to monitor TrOC removal during AOP, this study sheds light on the development of dynamic feedback-based strategies for precise and economical advanced treatment of wastewater.

Treatment of Organics in Wastewater Using Electrogenerated Gaseous Oxidants

This work focuses on the comparison of the performance of direct electrochemical oxidation with indirect electrolysis mediated by gaseous oxidants in the treatment of diluted wastewater. To do this, energy consumptions of the electrolysis using mixed metal oxide (MMO) electrodes are compared with those required for the production and use of chlorine dioxide in the degradation of methomyl contained in aqueous solutions. Results demonstrate the feasibility of the mediated oxidation process and that this process is competitive with direct oxidation. The oxidants are produced under optimized conditions using the same anodic material applied for the direct degradation of organics, thus avoiding efficiency losses associated with mass transfer limitations in the degradation of dilute organic solutions. Thus, using the ClO2 gaseous oxidant, a concentration of 0.1 mM of methomyl from a solution containing 500 mL is completely removed with an energy consumption as low as 50 Wh. The application of the same energy to a direct electrolytic process for treating the same wastewater can only reach less than half of this removal. These findings may have a very important application in the use of electrochemical technology to achieve the remediation of persistent pollutants in wastewater, where their low concentrations typically make direct processes very inefficient.

Advancements in combined electrocoagulation processes for sustainable wastewater treatment: A comprehensive review of mechanisms, performance, and emerging applications

This review explores the potential and challenges of combining electrochemical, especially electrocoagulation (EC) process, with various - wastewater treatment methods such as membranes, chemical treatments, biological methods, and oxidation processes to enhance pollutant removal and reduce costs. It emphasizes the advantages of using electrochemical processes as a pretreatment step, including increased volume and improved quality of permeate water, mitigation of membrane fouling, and lower environmental impact. Pilot-scale studies are discussed to validate the effectiveness of combined EC processes, particularly for industrial wastewater. Factors such as electrode materials, coating materials, and the integration of a third process are discussed as potential avenues for improving the environmental sustainability and cost-effectiveness of the combined EC processes. This review also discusses factors for improvement and explores the EC process combined with Advanced Oxidation Processes (AOP). The conclusion highlights the need for combined EC processes, which include reducing electrode consumption, evaluating energy efficiency, and conducting pilot-scale investigations under continuous flow conditions. Furthermore, it emphasizes future research on electrode materials and technology commercialization. Overall, this review underscores the importance of combined EC processes in meeting the demand for clean water resources and emphasizes the need for further optimization and implementation in industrial applications.

Recent Development of Metal-Organic Frameworks for Water Purification

Water contamination is an increasing concern to mankind because of the increasing amount of pollutants in aquatic ecosystems. To purify the polluted water, various techniques have been used to remove hazardous components. Unfortunately, traditional cleanup techniques with a low uptake capacity are unable to achieve water purification. Metal-organic frameworks (MOFs) have recently shown potential in effective water pollutant isolation in terms of selectivity and adsorption capacity over traditional porous materials. The high surface area and versatile functionality of MOFs allow for the development of new adsorbents. The development of MOFs in a range of water treatments in the recent five years will be highlighted in this review, along with assessments of the adsorption performance relevant to the particular task. Moreover, the outlook on future opportunities for water purification using MOFs is also provided.

Synthesis of stabilized zero-valent iron particles and role investigation of humic acid-Fex+ shell in Fenton-like reactions and surface stability control

Herein, a novel humic acid-Fex+ complex-coated ZVI (HA-Fex+@ZVI) was synthesized and used to activate peroxydisulfate (PDS) for phenol degradation. The HA-Fex+ shell selectively reacted with PDS rather than O2, leading to the formation of modified ZVI with excellent surface stability in storage and ultraefficient PDS activation in advanced oxidation processes (AOPs). As a result, the phenol degradation and PDS activation efficiencies of HA-Fex+@ZVI/PDS were ∼14.4 and ∼1.8 times higher than those of ZVI/PDS, respectively. Mechanistic explorations revealed that the replacement of the HA-Fex+ shell relative to the original passivation layer of ZVI greatly changed the SO4•- generation pathway from a heterogeneous process to a homogeneous process, resulting from the slow exposure of Fe0 (generating dissolved Fe2+) and the depolymerized HA (enhancing the Fe3+/Fe2+ cycle). Based on experimental analysis and density functional theory (DFT) calculations, the Fe3+ in HA-Fex+ could be reduced to Fe2+ by PDS, resulting in the disintegration of the HA-Fex+ shell and exposure of Fe0 core active sites. Furthermore, compared to similar catalysts synthesized with commercial HA and traditional chemicals, HA-Fex+@ZVI synthesized with multiple waste biomasses exhibited better performance. This research provides valuable insights for designing ZVI-based catalysts with excellent storage stability and ultraefficient PDS catalytic activity for AOPs.

The analytic hierarchy process method to design applicable decision making for the effective removal of 2-MIB and geosmin in water sources

Numerous utilities encounter issues with taste and odor that alter the public's impression of the safety of drinking water. The creation of certain components in water naturally due to global climate change is another source of taste and odor components, in addition to industrial emissions. Geosmin and 2-methylisoborneol (2-MIB), both of which are generated by blue-green algae and actinomycetes, are two substances that contribute to the musty and earthy smells in drinking water sources. Unfortunately, current conventional treatment plants only partially remove 2-MIB and geosmin. Therefore, to protect the environment and public health, more up-to-date or optimized treatment methods should be applied to outdated treatment facilities. Best treatment practices, evaluation standards, and decision-making approaches, however, are still shrouded in mystery. The goal of this study was to identify the most effective treatment options for 2-MIB and geosmin. By using the analytical hierarchy process (AHP), a total of 22 assessment criteria were found and prioritized. A thorough literature search led to the identification of potential treatment options, and their effectiveness was evaluated. These options and priority rankings were decided upon using AHP in the decision-making process. Advanced oxidation techniques came out on top in the final priority ranking, followed by membrane filtering, adsorption, oxidation, hybrid processes, and traditional treatment methods. The applied analytical decision techniques may also be used to choose the optimal treatment options, even though the results are particular to 2-MIB and geosmin.

Elucidating the performance of UV-based photochemical processes for the removal of trace organic contaminants: Degradation and toxicity evaluation

In this study, the performance of standalone ultraviolet (UV) photolysis and UV-based advanced oxidation processes (AOPs), namely, UV/hydrogen peroxide, UV/chlorine, UV/persulphate, and UV/permonosulphate, were investigated for the degradation of 31 trace organic contaminants (TrOCs). Under the tested conditions, standalone UV photolysis did not achieve effective removal of TrOCs. To improve the degradation efficiency of UV photolysis, four different oxidants were added individually to the test solution. The effect of these oxidants in the absence of UV irradiation was also explored and only chlorine showed promising degradation of some contaminants. During the chlorination of 31 investigated TrOCs, only six demonstrated greater than 50% degradation. The combined UV-based AOPs demonstrated much improved degradation (ranging from 65 to 100%) depending on TrOC-structure and oxidant concentration. The UV/hydrogen peroxide process showed similar degradation of TrOCs, irrespective of the functional groups (i.e., electron withdrawing groups, EWGs and electron donating groups, EDGs) present in their structures. Conversely, the UV/sulphate and UV/chlorine based processes achieved better degradation of the TrOCs with EDGs in their structures. TrOCs degradation improved up to 40% when oxidants concentrations were increased from 0.1 to 1 mM, and further increasing the concentration to 2 mM did not improve degradation. Toxicity evaluation using bioluminescence test (BLT assay) demonstrated that except for UV/hydrogen peroxide, all UV-based AOPs increased the toxicity of the treated effluent, indicating generation of toxic by-products. This study elucidates the performance of four different UV-based AOPs for the removal of commonly detected diverse TrOCs for the first time.

Hydrodynamic cavitation-enhanced activation of sodium percarbonate for estrogen removal

The present paper investigated the potential of hydrodynamic cavitation (HC) as an effective tool for activating sodium percarbonate (SPC). The method's efficiency was demonstrated by effectively removing estrogens, which are pollutants that have adverse impacts on aquatic ecosystems. The effects of the SPC concentration, temperature of solution, and cavitation time were evaluated. After SPC/HC treatment, the removal of estrogens was monitored by liquid chromatography-tandem mass spectrometry (LC -MS/MS). Already after 4 s of treatment and 24 h of reaction time, more than 97% of estrogens (initial concentration of 300 ng/L) were removed. The effect of post-treatment time is not considered in several papers, even though it seems to be crucial and is discussed here. The results were supported by the values of degradation rate constants, which fit the pseudo-first-order kinetic model. We also verified that HC alone was not effective for estrogen removal under the selected conditions. The sustainability of the SPC/HC system was evaluated based on electric energy per order calculation. The combination of SPC and HC is a promising approach for rapidly degrading micropollutants such as estrogenic compounds without the need for additional technological steps, such as pH or temperature adjustment.

Occurrence, toxicity, impact and removal of selected non-steroidal anti-inflammatory drugs (NSAIDs): A review

Non-steroidal anti-inflammatory drugs (NSAIDs) are among the most frequently used pharmaceuticals for human therapy, pet therapeutics, and veterinary feeds, enabling them to enter into water sources such as wastewater, soil and sediment, and seawater. The control of NSAIDs has led to the advent of the novel materials for treatment techniques. Herein, we review the occurrence, impact and toxicity of NSAIDs against aquatic microorganisms, plants and humans. Typical NSAIDs, e.g., ibuprofen, ketoprofen, diclofenac, naproxen and aspirin were detected at high concentrations in wastewater up to 2,747,000 ng L-1. NSAIDs in water could cause genotoxicity, endocrine disruption, locomotive disorders, body deformations, organs damage, and photosynthetic corruption. Considering treatment methods, among adsorbents for removal of NSAIDs from water, metal-organic frameworks (10.7-638 mg g-1) and advanced porous carbons (7.4-400 mg g-1) were the most robust. Therefore, these carbon-based adsorbents showed promise in efficiency for the treatment of NSAIDs.

Removal of water pollutants using plant-based nanoscale zero-valent iron: A review

Nanotechnology has been increasingly explored for the treatment of various waste streams. Among different nanoparticles, nanoscale zerovalent iron (nZVI) has been extensively investigated due to its high reactivity and strong reducing power. However, conventional methods for the synthesis of nZVI particles have several limitations and led to the green synthesis of nZVI using plant-based materials. Plant extracts contain various reducing agents that can be used for nZVI synthesis, eliminating the need for toxic chemicals, and reducing energy consumption. Additionally, each plant species used for nZVI synthesis results in unique physicochemical properties of the nanoparticles. This review paper provides an overview of plant-based nZVI particle synthesis, its characteristics, and its application for the removal of different classes of pollutants such as dyes, heavy metals, nutrients, and trace organic pollutants from water. The review shows that continued research on plant-based nZVI particles to fully understand its potential in wastewater treatment, especially for the removal of a wider variety of pollutants, and for improving sustainability and reducing the cost and environmental impact of the process, is necessary.

Performance of a Pilot-Scale Continuous Flow Ozone-Based Hospital Wastewater Treatment System

Antimicrobial resistance (AMR) is becoming a global concern. Recently, research has emerged to evaluate the human and environmental health implications of wastewater from medical facilities and to identify acceptable wastewater treatment methods. In this study, a disinfection wastewater treatment system using an ozone-based continuous flow system was installed in a general hospital located in Japan. The effectiveness of antimicrobial-resistant bacteria (ARB) and antimicrobials in mitigating the environmental impact of hospital wastewater was evaluated. Metagenomic analysis was conducted to characterize the microorganisms in the wastewater before and after treatment. The results demonstrated that ozone treatment enables effective inactivation of general gut bacteria, including Bacteroides, Prevotella, Escherichia coli, Klebsiella, DNA molecules, and ARGs, as well as antimicrobials. Azithromycin and doxycycline removal rates were >99% immediately after treatment, and levofloxacin and vancomycin removal rates remained between 90% and 97% for approximately one month. Clarithromycin was more readily removed than the other antimicrobials (81-91%), and no clear removal trend was observed for ampicillin. Our findings provide a better understanding of the environmental management of hospital wastewater and enhance the effectiveness of disinfection wastewater treatment systems at medical facilities for mitigating the discharge of pollutants into aquatic environments.

Antibiotic sorption onto microplastics in water: A critical review of the factors, mechanisms and implications

Microplastics as vectors for contaminants in the environment is becoming a topic of public interest. Microplastics have been found to actively adsorb heavy metals, per-fluorinated alkyl substances (PFAS), polychlorinated biphenyls (PCBs), polyaromatic hydrocarbons (PAHs), pharmaceuticals and personal care products (PPCPs) and polybrominated diethers (PBDs) onto their surface. Particular interest in microplastics capacity to adsorb antibiotics needs further attention due to the potential role this interaction plays on antibiotic resistance. Antibiotic sorption experiments have been documented in the literature, but the data has not yet been critically reviewed. This review aims to comprehensively assess the factors that affect antibiotic sorption onto microplastics. It is recognised that the physico- chemical properties of the polymers, the antibiotic chemical properties, and the properties of the solution all play a crucial role in the antibiotic sorption capacity of microplastics. Weathering of microplastics was found to increase the antibiotic sorption capacity by up to 171%. An increase in solution salinity was found to decrease the sorption of antibiotics onto microplastics, in some instances by 100%. pH also has a substantial effect on sorption capacity, illustrating the significance of electrostatic interactions on the sorption of antibiotics onto microplastics. The need for a uniform experimental design when testing antibiotic sorption is highlighted to remove inconsistencies in the data currently presented. Current literature examines the link between antibiotic sorption and antibiotic resistance, however, further studies are still required to fully understand this emerging global crisis.

Enhanced degradation of 2,6-dimethylphenol by photocatalytic systems using TiO2 assisted with H2O2 and Fe(III)

In this study, several photocatalytic degradation systems were investigated using 2,6-dimethylphenol (2,6-DMP) as a model compound. Highly reactive species are formed in four systems, Fe(III), TiO₂, TiO₂/H₂O₂ and TiO₂/Fe(III) where complete degradation of 2,6-DMP was achieved under UV radiation. Photodegradation of the 2,6-DMP has been described by pseudo-first order kinetic model in the presence of TiO₂. In UV/TiO₂-H₂O₂ system, the addition of H₂O₂ in the TiO₂ suspension improves the degradation rate of 2,6-DMP from 70% to 100% for a H₂O₂ concentration of 10^-2 M in 3 h. In homogeneous system, HO^• and Fe²⁺ can be generated by the irradiation of Fe(III) solution. The speciation of Fe(III) obtained from Visual MINTEQ soft showed the formation of several species and Fe(OH)²⁺ were the most predominant and active species in a pH range of 2.5-3.5. At a low concentration of TiO₂ (30 mg L^-1), an important positive effect due to the iron addition has been shown in TiO₂/Fe(III) system, the entrance of metallic ions at different concentrations enhanced the photocatalytic activity of TiO₂. A degradation percentage of 90% was achieved in the UV/TiO₂-Fe(III) system under optimal conditions against 57% in UV/TiO₂ system. Strong synergistic effect was observed in the UV/TiO₂-H₂O₂ binary system. On the basis of literature, a pathway for 2,6-DMP degradation was proposed. The mechanism of degradation of the 2,6-DMP did not involve only HO^• radicals, an interaction of Fe(III) in the excited state with 2,6-DMP occurred giving rise to the formation of 2,6-dimethylphenoxyl radical.

Porous Materials for Water Purification

Water pollution is a growing threat to humanity due to the pervasiveness of contaminants in water bodies. Significant efforts have been made to separate these hazardous components to purify polluted water through various methods. However, conventional remediation methods suffer from limitations such as low uptake capacity or selectivity, and current water quality standards cannot be met. Recently, advanced porous materials (APMs) have shown promise in improved segregation of contaminants compared to traditional porous materials in uptake capacity and selectivity. These materials feature merits of high surface area and versatile functionality, rendering them ideal platforms for the design of novel adsorbents. This Review summarizes the development and employment of APMs in a variety of water treatments accompanied by assessments of task-specific adsorption performance. Finally, we discuss our perspectives on future opportunities for APMs in water purification.

OH-initiated degradation of 1,2,3-trimethylbenzene in the atmosphere and wastewater: Mechanisms, kinetics, and ecotoxicity

1,2,3-Trimethylbenzene (1,2,3-TMB) is an important volatile organic compound (VOC) present in petroleum wastewater and the atmosphere. This compound can be degraded by OH radicals via abstraction, addition and substitution mechanisms. Results show that the addition mechanism is dominant and H-abstraction is subdominant, while methyl abstraction and substitution mechanisms are negligible in the gas and aqueous phases. Moreover, H-abstraction products undergo further reactions with O₂, NO, NO₂, H₂O, and OH radicals in the atmosphere. Time-dependent density functional theory (TDDFT) calculations show that the degraded products, including 2,3,4-trimethylphenyl-nitroperoxoite, 1,2,3-trimethyl-4-nitrobenzene, 1,2,3-trimethyl-5-nitrobenzene, 2,6-dimethylbenzyl nitroperoxoite, 2,3-dimethylphenyl nitroperoxoite, 2,6-dimethylbenzaldehyde, and 2,3-dimethylbenzaldehyde, can photolyze under the sunlight. Kinetically, the calculated total rate constant is 5.57 × 10^-11 cm³ molecule^-1·s^-1 at 1 atm and 298 K, which is consistent with available experimental values measured in the atmosphere. In addition, the calculated total reaction rate constant in water is close to that in the gas phase. In terms of ecotoxicity, all degradation products are less toxic than the initial reactant to fish, green algae and daphnia. For mammals represented by rats, 1,2,3-TMB and its products are moderately toxic, except for 2,3-dimethylphenol and 2,6-dimethylphenol, which are slightly toxic.

Role of UV-based advanced oxidation processes on NOM alteration and DBP formation in drinking water treatment: A state-of-the-art review

Oxidative treatment of drinking water has been practiced for more than a century. UV-based advanced oxidation processes (UV-AOPs) have emerged as promising oxidative treatment technologies to eliminate recalcitrant chemicals and biological contaminants in drinking water. UV-AOPs inevitably alter the properties of natural organic matter (NOM) and affect the disinfection byproduct (DBP) formation in the post-disinfection. This paper provides a state-of-the-art review on the effects of UV-AOPs on the changes of NOM properties and the consequent impacts on DBP formation in the post-chlorination process. A tutorial review to the connotations of NOM properties (e.g., bulk properties, fractional constituents, and molecular structures) and the associated state-of-the-art analytical methods are firstly presented. The impacts of different radical-based AOPs on the changes of NOM properties together with the underlying NOM-radical reaction mechanisms are discussed. The impacts of alteration of NOM properties on DBP formation in the post-chlorination process are then reviewed. The current knowledge gaps and future research needs are finally presented, with emphases on the needs to strengthen the comparability of research data in literature, the accuracy in quantifying the reactive moieties of NOM, and the awareness of unknown DBPs in oxidative water treatment processes. The review and discussion improve the fundamental understanding of NOM-radical and NOM-chlorine chemistry. They also provide useful implications on the engineering design and operation of next-generation drinking water treatment plants.

Degradation of tetracycline by UV/Fe3+/persulfate process: Kinetics, mechanism, DBPs yield, toxicity evaluation and bacterial community analysis

As a widely produced and used antibiotic, tetracycline (TC) has been frequently found in rivers, soil and drinking water. In this study, the degradation of TC was investigated by UV/Fe³⁺/persulfate (PS) coupled process. The degradation behavior was well fitted with pseudo-first-order model. Hydroxyl radicals (·OH), sulfate radicals (SO₄^-·) and superoxide radical (O₂^-·) were identified as the primary reactive oxygen species (ROS) in UV/Fe³⁺/PS process, the contribution to TC degradation were found to be 41.94%, 33.94% and 17.44% at pH 3.0, respectively. Fe(IV) generated from the system also played a crucial role in TC removal. The effects of process parameters (PS/Fe³⁺ dosages, pH, humic acid, Cl^-, HCO₃^-, NO₃^- and CO₃^2-) on degradation were investigated. It was found that the degradation of TC was highly pH-dependent, and the optimal performance was obtained at pH 3.0. Except for Cl^-, the presence of HA, HCO₃^-, NO₃^- and CO₃^2- inhibited TC degradation. The possible transformation pathway involving the hydroxylation, N-demethylation, hydrogenation and dehydroxylation was proposed. Furthermore, the toxicity and mutagenicity of TC and transformation products (TPs) were estimated using ECOSAR and TEST softwares, demonstrating that the toxicity level of most TPs was lower/equal to their precursors. The evaluation of DBPs showed that UV/Fe³⁺/PS process could reduce the potential of DBPs formation, especially for TCAA and TCM. Microbial community composition was analyzed by 16 S rDNA sequencing, and the relative abundance of ARG-carrying opportunistic pathogens was significantly declined after UV/Fe³⁺/PS treatment. In general, this study provides an economical, efficient and safe strategy for TC removal.

Impact of water matrices on oxidation effects and mechanisms of pharmaceuticals by ultraviolet-based advanced oxidation technologies: A review

The binding between water components (dissolved organic matters, anions and cations) and pharmaceuticals influences the migration and transformation of pollutants. Herein, the impact of water matrices on drug degradation, as well as the electrical energy demands during UV, UV/catalysts, UV/O₃, UV/H₂O₂-based, UV/persulfate and UV/chlorine processes were systemically evaluated. The enhancement effects of water constituents are due to the powerful reactive species formation, the recombination reduction of electrons and holes of catalyst and the catalyst regeneration; the inhibition results from the light attenuation, quenching effects of the excited states of target pollutants and reactive species, the stable complexations generation and the catalyst deactivation. The transformation pathways of the same pollutant in various AOPs have high similarities. At the same time, each oxidant also can act as a special nucleophile or electrophile, depending on the functional groups of the target compound. The electrical energy per order (EEO) of drugs degradation may follow the order of EEO_UV > EEO_UV/catalyst > EEO_UV/H2O2 > EEO_UV/PS > EEO_UV/chlorine or EEO_UV/O3. Meanwhile, it is crucial to balance the cost-benefit assessment and toxic by-products formation, and the comparison of the contaminant degradation pathways and productions in the presence of different water matrices is still lacking.

Modelling of the photo-Fenton process with flexible hydrogen peroxide dosage: Sensitivity analysis and experimental validation

The supply of hydrogen peroxide (H₂O₂) controlling the amount of highly oxidant hydroxyl radicals is the most critical operational issue for the photo-Fenton process. Accordingly, this study addresses the development of a model for photo-Fenton processes including a flexible H₂O₂ supply given as a function of time. The model is aimed at its future exploitation in treatment optimization and the determination of the optimal profile for H₂O₂ supply. The work has adopted a photo Fenton model previously reported that includes the inlet flow (fed-batch) and describes the system dynamics under a flexible dosage. Thus, model global sensitivity analysis (GSA) and parameter estimation were performed using Simulink® to examine the behavior of the model under flexible H₂O₂ dosage. GSA was carried out using partial rank correlation methods and the Latin hypercube sampling to assess to which extent variations of the model parameters affect each measured response (H₂O₂, total organic carbon, TOC, and dissolved oxygen, O₂ -the experimentally available information). Hence, the model is discussed in regard of its hypothesis and chances for reducing its complexity. This resulted in the rejection of two reactions of the initial model. Next, a set of 12 kinetic, stoichiometric and operative parameters was estimated through the fitting of H₂O₂, TOC, and O₂ profiles. Discussion on model fitting includes computational issues, the role of initial values for the estimation process, the goodness of fit criteria, and the sampling method. The model was fit to experimental data with assorted H₂O₂ supply profiles and validated, and Root Mean Square Error (RMSE) below 0.009 mM, 0.42 mM, and 0.127 mM were obtained for TOC, H₂O₂ and O₂, respectively. Therefore, this work contributes a practical model aimed at providing model-based optimization for the H₂O₂ dosage profile of the photo-Fenton process.

Synergistic Mechanism of Photocatalysis and Photo-Fenton by Manganese Ferrite and Graphene Nanocomposite Supported on Wood Ash with Real Sunlight Irradiation

The present research aimed to evaluate the photocatalytic activity of reduced graphene oxide and manganese ferrite nanocomposite supported on eucalyptus wood ash waste (WA) from industrial boilers, for the decolorization of methylene blue (MB) solutions, using sunlight as an irradiation source. For this, the photocatalyst named MnFe2O4-G@WA was synthesized by a solvothermal method and characterized by analyzes of scanning electron microscopy, transmission electron microscopy, X-ray diffraction, Fourier-transform infrared spectroscopy, Brunauer–Emmett–Teller and zeta potential. Firstly, the photocatalyst was evaluated for photocatalytic decolorization of MB under different reaction conditions. Then, the influence of pH, photocatalyst dose and H2O2 was evaluated. MnFe2O4-G@WA showed 94% of efficiency for photocatalytic decolorization of MB under operating conditions of solar irradiation, 0.25 g/L of catalyst, 300 mg/L of H2O2. The proposed degradation reaction mechanism suggested that the photodegradation of MB was through a synergistic mechanism of photocatalysis and photo-Fenton reactions, with the combined action of the three materials used. The data adjusted to the first order kinetics from the Langmuir–Hinshelwood model. In addition, MnFe2O4-G@WA showed high stability, maintaining its efficiency above 90% after 5 cycles. The results indicated that the nanophotocatalyst is a potential technology for the decolorization of MB solutions.

Conductive polymer layered semiconductor for degradation of triclopyr acid and 2,4-dichlorophenoxyacetic acid from aqueous stream using coalesce adsorption-photocatalysis technique

Polyaniline supported titanium dioxide nanoparticles (PTs) were fabricated using chemical oxidative aniline polymerization in the presence of titanium dioxide with ammonium peroxydisulfate as an oxidant. The synthesized PTs were thoroughly characterized for their morphological and functional features. PTs were employed for the photodegradation of acidic herbicides; 2,4-dichlorophenoxyacetic acid (2,4-D) and triclopyr acid (TCP). PT's surface modifications were imparted and their herbicide removal efficiencies were compared. The best operating conditions for adsorption/photocatalysis were 0.5 g/L photocatalyst, 10 mg/L concentration of individual herbicides resulted in 90.72% removal of TCP at pH 4 and 99.91% removal of 2,4-D at pH 5. Adsorption kinetics of herbicides, onto PT-1 showed the equilibrium attainment within 30 min and experimental data obeyed pseudo-second order model for TCP and 2,4-D removal which was governed by chemisorption. Analysis of TCP and 2,4-D adsorption indicated that the removal followed Sips model for TCP removal while Redlich-Peterson model explained the removal of 2,4-D by PT-1. Rate constants indicated that the amount of TiO₂ in the PTs played an important role in removing the herbicides and PT-1 material excellent remarkable activity for three cycles of photodegradation. Thus, this work reports the polymerization of aniline onto TiO₂ and their utility as photocatalyst for the expulsion of 2,4-D and TCP from water.

Inactivation of Bacteria and Residual Antimicrobials in Hospital Wastewater by Ozone Treatment

The emergence and spread of antimicrobial resistance (AMR) has become a persistent problem globally. In this study, an ozone treatment facility was established for an advanced hospital wastewater treatment in a core hospital facility in an urban area in Japan to evaluate the inactivation of antimicrobial-resistant bacteria and antimicrobials. Metagenomic DNA-seq analysis and the isolation of potential extended-spectrum β-lactamase (ESBL)-producing bacteria suggested that ozone exposure for at least 20 min is required for the adequate inactivation of DNA and ESBL-producing bacteria. Escherichia coli and Klebsiella species were markedly susceptible to 20-min ozone exposure, whereas Raoultella ornithinolytica and Pseudomonas putida were isolated even after an 80-min exposure. These ozone-resistant bacteria might play a pivotal role as AMR reservoirs in the environment. Nine antimicrobials (ampicillin, cefdinir, cefpodoxime, ciprofloxacin, levofloxacin, clarithromycin, chlortetracycline, minocycline, and vancomycin) were detected at 373 ng/L to 27 μg/L in the hospital wastewater, and these were removed (96–100% removal) after a 40-min treatment. These results facilitate a comprehensive understanding of the AMR risk posed by hospital wastewater and provides insights for devising strategies to eliminate or mitigate the burden of antimicrobial-resistant bacteria and the flow of antimicrobials into the environment. To the best of our knowledge, this is the first report on the implementation of a batch-type, plant-scale ozone treatment system in a hospital facility to execute and evaluate the inactivation of drug-resistant bacteria and antimicrobials.

Natural Volcanic Material as a Sustainable Photocatalytic Material for Pollutant Degradation under Solar Irradiation

Recently, photocatalysis has been demonstrated as a solid approach for efficient wastewater cleaning. Using natural materials as photocatalysts means a promising solution to develop green catalysts for environmental purposes. This work aimed to study the suitability of a natural volcanic material (La Gomera, Canary Islands, Spain) as a photocatalytic material for the degradation of pollutants in wastewater with solar energy. After analysing the properties of the natural material (BET surface 0.188 m²/g and band-gap of 3 eV), the photocatalytic activity was evaluated at laboratory and pilot plant scale for the degradation of methylene blue (MB) in water (50 mg L⁻¹), at 20 °C, during a period of 4 h, under UV/Vis light and solar irradiation. Photolytic and adsorption studies were developed to distinguish the photocatalytic contribution to the wastewater decontamination process by photocatalysis. Our results enable us to determine the viability of black sand as a photocatalytic material activated by solar irradiation (photodegradation of MB up to 100% by using solar energy), developing a natural and green photocatalytic system with significantly high potential for application in a sustainable wastewater cleaning process.

Recent Progress in the Removal of Legacy and Emerging Organic Contaminants from Wastewater Using Metal-Organic Frameworks: An Overview on Adsorption and Catalysis Processes

Water covers about 70% of the Earth’s surface, but the amount of freshwater available for human use is only 2.5% and, although it is continuously replenished via the water cycle, freshwater is a finite and limited resource. The Earth’s water is affected by pollution and while water quality is an issue of global concern, the specific regulations on contaminants of emerging concern (CECs) are limited. In order to achieve the goals set by EU regulations, the treatment of wastewater is a scientifically and technologically challenging issue. Metal–organic frameworks (MOFs) are promising materials used for the removal of priority and emerging contaminants from wastewater, since they can mitigate those contaminants via both adsorption as well as catalysis processes. MOFs can offer selective adsorption of CECs by various adsorption mechanisms. The catalytic removal of priority and emerging organic contaminants from wastewater using MOFs implies Fenton, electro-Fenton, and photo-Fenton processes. Overall, MOFs can be considered as promising materials for the elimination of priority and emerging organic contaminants from various wastewater types, but the involved processes must be studied in detail for a larger number of compounds.

Efficient peroxymonosulfate (PMS) activation by visible-light-driven formation of polymorphic amorphous manganese oxides

Heterogeneous sulfate radical-based advanced oxidation processes (SR-AOPs) have been widely reported over the last decade as a promising technology for pollutant removal from wastewater. In this study, a novel peroxymonosulfate (PMS) activator was obtained by visible-light-driven Mn(II) oxidation in the presence of nitrate. The photochemically synthesized manganese oxides (PC-MnO_x) were polymorphic amorphous nanoparticles and nanorods, with an average oxidation state of approximately 3.0. It possesses effective PMS activation capacity and can remove 20 mg L^-1 acid organic II (AO7) within 30 min. The AO7 removal performance of PC-MnO_x was slightly decreased in natural waterbodies and in the presence of CO₃^2-, while it showed an anti-interference capacity for Cl^-, NO₃^- and humic acid. Chemical quenching, reactive oxygen species (ROS) trapping, X-ray photoelectric spectroscopy (XPS), in-situ Raman spectroscopy, and electrochemical experiments supported a nonradical mechanism, i.e., electron transfer from AO7 to the metastable PC-MnO_x-PMS complex, which was responsible for AO7 oxidation. The PC-MnO_x-PMS system also showed substrate preferences based on their redox potentials. Moreover, PC-MnO_x could activate periodate (PI) but not peroxydisulfate (PDS) or H₂O₂. Overall, this study provides a new catalyst for PMS activation through a mild and green synthesis approach.

Stability and Removal of Benzophenone-Type UV Filters from Water Matrices by Advanced Oxidation Processes

Benzophenone (BP) type UV filters are common environmental contaminants that are posing a growing health concern due to their increasing presence in water. Different studies have evidenced the presence of benzophenones (BP, BP-1, BP-2, BP-3, BP-4, BP-9, HPB) in several environmental matrices, indicating that conventional technologies of water treatment are not able to remove them. It has also been reported that these compounds could be associated with endocrine-disrupting activities, genotoxicity, and reproductive toxicity. This review focuses on the degradation kinetics and mechanisms of benzophenone-type UV filters and their degradation products (DPs) under UV and solar irradiation and in UV-based advanced oxidation processes (AOPs) such as UV/H₂O₂, UV/persulfate, and the Fenton process. The effects of various operating parameters, such as UV irradiation including initial concentrations of H₂O₂, persulfate, and Fe²⁺, on the degradation of tested benzophenones from aqueous matrices, and conditions that allow higher degradation rates to be achieved are presented. Application of nanoparticles such as TiO₂, PbO/TiO₂, and Sb₂O₃/TiO₂ for the photocatalytic degradation of benzophenone-type UV filters was included in this review.

Synergistic effect of ultrasonication and sulfate radical on recovering cobalt and lithium from the spent lithium-ion battery

Ultrasonication has been mechanically applied widely in the recycling of spent lithium-ion (SLI) batteries while its influence on chemical pathways has barely been reported. In this study, ultrasonication and sulfate radicals were used in a coupling system to obtain efficient recoveries of Co and Li from SLI batteries. The synergistic effect of ultrasonication and sulfate radicals on recycling was quantitatively analysed by significance analysis and surface responses in a central composite design. The employment of persulfate significantly affected the whole recycling process during the sonication. Factors including acoustic time, operating powers, and temperature all had a significant effect on the recoveries of Co and Li. The maximum recovery efficiencies of Co and Li of 97.33% and 99.25%, respectively, and the minimum loss rate of Al of 4.13% were simultaneously obtained by the fitting predictor. The optimal combination of factors for the sonication system included an acoustic time (min) of 5.5, an operating power (W) of 168, a temperature (°C) of 86, and a ratio of cathode foil to S-solution (mg/mL) of 1:60. A moiety of cathode active material was directly separated from the aluminium collector by sulfate radical-related reactions. Co and Li cations dissolved from LiCoO₂ by carbon dioxide radicals were reprecipitated by excess oxalate. The research demonstrated the positively synergistic influence caused by ultrasonication and sulfate radicals on achieving efficient recoveries of Co and Li from SLI batteries, explicitly expanding the technical choices for the recycling procedure.

A review of microwave-assisted advanced oxidation processes for wastewater treatment

Microwave (MW) technology has gained increasing interest in wastewater treatment due to its unique properties, such as fast and uniform heating, hot spots effect, and non-thermal effect. MW enhances the production of active radicals (e.g., OH, SO₄^-), which exerts a stronger integrated treatment effect in combination with advanced oxidation processes. Over the years, microwave-assisted advanced oxidation processes (MW-AOPs) have developed rapidly to degrade pollutants as innovative treatment approaches. This paper provides a detailed classification and a comprehensive review of MW-AOPs. The latest applications of MW in different advanced oxidation systems (oxidation systems, catalytic oxidation systems, and photochemical, electrochemical and sonochemical systems) are reviewed. The reaction parameters and performance of MW-AOPs in wastewater treatment are discussed, and the enhancement of pollutant degradation by MW is highlighted. In addition, the operating costs of MW-AOPs are evaluated. Some recommendations on MW-AOPs are made for future research. This review provides meaningful information on the potential development and evolution of MW-AOPs.

Enhanced activation of persulfate by CuCoFe2O4@MC/AC as a novel nanomagnetic heterogeneous catalyst with ultrasonic for metronidazole degradation

In this study, the degradation of Metronidazole (MNZ) using CuCoFe₂O₄@MC/AC catalyst synthesized by microwave-assisted method, as an efficient activator for persulfate (PS) in the presence of ultrasonic (US: 60 kHz) was investigated. X-ray powder diffraction (XRD), Field emission scanning electron microscope (FESEM), Energy dispersive spectroscopy (EDS)-Mapping and Line scan, Fourier transform infrared spectroscopy (FTIR), Vibrating-sample magnetometer (VSM), and Thermal gravimetric analysis (TGA) were conducted to characterize the structure of CuCoFe₂O₄@MC/AC catalyst and then the catalyst dose, PS dose, MNZ concentration, and pH parameters were optimized. The maximum MNZ degradation of 93.78 % was achieved after 15 min reaction at the optimized operation conditions: 0.4 g L^-1 of catalyst, 6 mM of PS, 5 mg L^-1 of MNZ, and pH of 3. The removal efficiency of Total Organic Carbon (TOC) was 87.5 % under optimal conditions. According to kinetic equations, it was found that the MNZ degradation followed both kinetics (pseudo-first-order and Langmuir-Hinshelwood) based on the coefficient of determination (R²) of 0.949, 0.9716, 0.9073, 0.9721, and 0.9662 at concentrations of 5, 10, 15, 20, and 30, respectively. The surface reaction rate constant (K_c) and the adsorption equilibrium constant (K_L-H) of the Langmuir-Hinshelwood model were 0.81 (mg L^-1 min^-1) and 2.184 (L mg^-1), respectively. The free radical scavenging experiments were conducted to illustration the proposed mechanism, which shown that the SO₄^-• was the predominant radicals involved in MNZ degradation. Finally, the regeneration of the catalyst was investigated and showed that after five cycles of use and regeneration by chemical and thermal methods, this catalyst has acceptable chemical stability.

A review on environmental occurrence, toxicity and microbial degradation of Non-Steroidal Anti-Inflammatory Drugs (NSAIDs)

In recent years, Non-Steroidal Anti-Inflammatory Drugs (NSAIDs) have surfaced as a novel class of pollutants due to their incomplete degradation in wastewater treatment plants and their inherent ability to promote physiological predicaments in humans even at low doses. The occurrence of the most common NSAIDs (diclofenac, ibuprofen, naproxen, and ketoprofen) in river water, groundwater, finished water samples, WWTPs, and hospital wastewater effluents along with their toxicity effects were reviewed. The typical concentrations of NSAIDs in natural waters were mostly below 1 μg/L, the rivers receiving untreated wastewater discharge have often showed higher concentrations, highlighting the importance of effective wastewater treatment. The critical analysis of potential, pathways and mechanisms of microbial degradation of NSAIDs were also done. Although studies on algal and fungal strains were limited, several bacterial strains were known to degrade NSAIDs. This microbial ability is attributed to hydroxylation by cytochrome P450 because of the decrease in drug concentrations in fungal cultures of Phanerochaete sordida YK-624 on incubation with 1-aminobenzotriazole. Moreover, processes like decarboxylation, dehydrogenation, dechlorination, subsequent oxidation, demethylation, etc. also constitute the degradation pathways. A wide array of enzymes like dehydrogenase, oxidoreductase, dioxygenase, monooxygenase, decarboxylase, and many more are upregulated during the degradation process, which indicates the possibility of their involvement in microbial degradation. Specific hindrances in upscaling the process along with analytical research needs were also identified, and novel investigative approaches for future monitoring studies are proposed.

Acid mine drainage and sewage impacted groundwater treatment by membrane distillation: Organic micropollutant and metal removal and membrane fouling

Groundwater is the dominant source of freshwater in many countries around the globe, and the deterioration in its quality by contaminants originating from anthropogenic sources raises serious concern. In this study, a scenario where groundwater is contaminated by acid mine drainage (AMD) from mining activities and/or sewage was envisaged, and the performance of a direct contact membrane distillation (DCMD) system was investigated comprehensively for different compositions of the AMD- and sewage-impacted groundwater. Regardless of the composition, MD membrane achieved 98-100% removal of metals and bulk organics, while the removal of the selected micropollutants ranged between 80 and 100%. Effective retention of contaminants by the MD led to their accumulation over time, which affected the hydraulic performance of the MD membrane by reducing the permeate flux by 29-76%. When persulfate (PS)-mediated oxidation process was integrated with the DCMD, degradation of bulk organics (50-71%) and micropollutants (50-100%) by PS reduced their accumulation. Characterisation of the fouling layer revealed the occurrence of membrane scaling that was mainly due to the deposition of iron oxide or oxyhydroxide precipitates. For an identical composition of the AMD- and sewage-impacted groundwater, flux decline was 10% less in PS-assisted DCMD as compared to that in the standalone DCMD. However, this did not prevent the formation of iron oxide scales on MD membrane during the operation of PS-assisted DCMD. This study demonstrates the long-term performance of a standalone and PS-assisted DCMD operated in continuous-flow mode to treat AMD- and sewage-impacted groundwater for the first time.

A Review on the Treatment of Petroleum Refinery Wastewater Using Advanced Oxidation Processes

The petroleum industry is one of the most rapidly developing industries and is projected to grow faster in the coming years. The recent environmental activities and global requirements for cleaner methods are pushing the petroleum refining industries for the use of green techniques and industrial wastewater treatment. Petroleum industry wastewater contains a broad diversity of contaminants such as petroleum hydrocarbons, oil and grease, phenol, ammonia, sulfides, and other organic composites, etc. All of these compounds within discharged water from the petroleum industry exist in an extremely complicated form, which is unsafe for the environment. Conventional treatment systems treating refinery wastewater have shown major drawbacks including low efficiency, high capital and operating cost, and sensitivity to low biodegradability and toxicity. The advanced oxidation process (AOP) method is one of the methods applied for petroleum refinery wastewater treatment. The objective of this work is to review the current application of AOP technologies in the treatment of petroleum industry wastewater. The petroleum wastewater treatment using AOP methods includes Fenton and photo-Fenton, H2O2/UV, photocatalysis, ozonation, and biological processes. This review reports that the treatment efficiencies strongly depend on the chosen AOP type, the physical and chemical properties of target contaminants, and the operating conditions. It is reported that other mechanisms, as well as hydroxyl radical oxidation, might occur throughout the AOP treatment and donate to the decrease in target contaminants. Mainly, the recent advances in the AOP treatment of petroleum wastewater are discussed. Moreover, the review identifies scientific literature on knowledge gaps, and future research ways are provided to assess the effects of these technologies in the treatment of petroleum wastewater.

The Evolution of Photocatalytic Membrane Reactors over the Last 20 Years: A State of the Art Perspective

The research on photocatalytic membrane reactors (PMRs) started around the year 2000 with the study of wastewater treatment by degradation reactions of recalcitrant organic pollutants, and since then the evolution of our scientific knowledge has increased significantly, broadening interest in reactions such as the synthesis of organic chemicals. In this paper, we focus on some initial problems and how they have been solved/reduced over time to improve the performance of processes in PMRs. Some know-how gained during these last two decades of research concerns decreasing/avoiding the degradation of the polymeric membranes, improving photocatalyst reuse, decreasing membrane fouling, enhancing visible light photocatalysts, and improving selectivity towards the reaction product(s) in synthesis reactions (partial oxidation and reduction). All these aspects are discussed in detail in this review. This technology seems quite mature in the case of water and wastewater treatment using submerged photocatalytic membrane reactors (SPMRs), while for applications concerning synthesis reactions, additional knowledge is required.

Recent progress in transition metal oxide/sulfide quantum dots-based nanocomposites for the removal of toxic organic pollutants

Water is an essential solvent that is extremely necessary for the survival of life. Water pollution due to the increased utilization of water for various processes, including domestic and industrial activities, poses a special threat that contaminates both surface and ground water. In recent years, advanced oxidation processes (AOPs) have been applied to deal with wastewater problems, which is a green method used to oxidize organic contaminants with strong oxidative radical species. Among the AOPs, photocatalytic technology is one of the most promising strategies for wastewater cleaning, which fulfills the aims of environmentally friendly and sustainable development. Owing to their unique electronic, optical, and structural properties, nanoscale semiconductors have received substantial interest as materials for AOPs, particularly inspired by their superb quantum confinement effects and large surface-area-to-volume ratio, which are essential for catalytic reaction kinetics. Recent advancements have revealed that semiconductor nanocrystals, known as quantum dots (QDs), are newly emerging zero-dimensional (0-D) nanomaterials, which have garnered much attention owing to their special physiochemical characteristics such as high conductivity, thermo-chemical and opto-mechanical stability, high adsorption coefficients, and, most importantly, their admirable recyclability. In this review, we provide a clear understanding of the importance of semiconductor QD-based nanocomposites in the degradation of organic pollutants, in addition to the mechanism involved in the reaction process. Following this, the enhancement of different materials, such as metal oxides and metal sulfide QD-based nanocomposites, is discussed in the context of combating environmental pollution.

Sonochemical Synthesis, Characterization and Optical Properties of Tb-Doped CdSe Nanoparticles: Synergistic Effect between Photocatalysis and Sonocatalysis

In this study, Tb-doped CdSe nanoparticles with variable Tb³⁺ content were synthesized by a simple sonochemical technique. The synthesized nanoparticles were characterized by X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and powder X-ray diffraction (XRD). The sono-photocatalytic activities of the as-prepared specimens were assessed for the degradation of Reactive Black 5. The experimental results show that the sono-photocatalytic process (85.25%) produced a higher degradation percentage than the individual sono- (22%) and photocatalytic degradation (8%) processes for an initial dye concentration and Tb-doped CdSe dosage of 20 mg/L and 1 g/L, respectively. Response surface methodology (RSM) was utilized to assess model and optimize the impacts of the operational parameters, namely, the Tb³⁺ content, initial dye concentration, catalyst dosage, and time. The addition of benzoquinone results in remarkably inhibited degradation and the addition of ammonium oxalate reduced the removal percentage to 24%. Superoxide radicals and photogenerated holes were detected as the main oxidative species.

Enhanced Degradation of Sulfonamide Antibiotics by UV Irradiation Combined with Persulfate

In this study, the degradation of sulfonamide antibiotics was investigated through persulfate-enhanced UV advanced oxidation process. Factors that may affect the degradation efficiency were analyzed. Results showed that the persulfate imposed a significant enhancement on the UV oxidation process during the sulfathiazole degradation. The combined process of UV/persulfate can effectively remove about 96% of sulfathiazole within 60 min. With the increase in the dosage of persulfate, the removal efficiency increased as well. Different water matrix almost had no effect on the removal efficiency. Two intermediates were found during the sulfathiazole degradation. It can be predicted that the combined process of UV/persulfate has a broad application prospect for removing sulfonamide antibiotics in water treatment.