Removal of emerging contaminants from the environment by adsorption

Limitations of wastewater treatment plants in removing trace anthropogenic biomarkers and future directions: A review

This review highlights the limitations faced by conventional wastewater treatment plants (WWTPs) in effectively removing contaminants of emerging concern (CECs), heavy metals (HMs), and Escherichia coli (E. coli). This emphasises the limitations of current treatment methods and advocates for innovative approaches to enhance the removal efficiency. By following the PRISMA guidelines, the study systematically reviewed relevant literature on detecting and remedying these pollutants in wastewater treatment facilities. Conventional wastewater treatment plants struggle to eliminate CECs, HMs, and E. coli owing to their small size, persistence, and complex nature. The review suggests upgrading WWTPs with advanced tertiary processes to significantly improve contaminant removal. This calls for cost-effective treatment parameters and standardised assessment techniques to enhance the fate of MPs in WWTPs and WRRFs. It recommends integrating insights from mass-balance model studies on MPs in WWTP to overcome modelling challenges and ensure model reliability. In conclusion, this review underscores the urgent need for advancements in wastewater treatment processes to mitigate the environmental impact of trace anthropogenic biomarkers. Future efforts should focus on conducting comprehensive studies, implementing advanced treatment methods, and optimising management practices in WWTPs and WRRFs.

Comprehensive review of emerging contaminants: Detection technologies, environmental impact, and management strategies

Emerging contaminants (ECs) are a diverse group of unregulated pollutants increasingly present in the environment. These contaminants, including pharmaceuticals, personal care products, endocrine disruptors, and industrial chemicals, can enter the environment through various pathways and persist, accumulating in the food chain and posing risks to ecosystems and human health. This comprehensive review examines the chemical characteristics, sources, and varieties of ECs. It critically evaluates the current understanding of their environmental and health impacts, highlighting recent advancements and challenges in detection and analysis. The review also assesses existing regulations and policies, identifying shortcomings and proposing potential enhancements. ECs pose significant risks to wildlife and ecosystems by disrupting animal hormones, causing genetic alterations that diminish diversity and resilience, and altering soil nutrient dynamics and the physical environment. Furthermore, ECs present increasing risks to human health, including hormonal disruptions, antibiotic resistance, endocrine disruption, neurological effects, carcinogenic effects, and other long-term impacts. To address these critical issues, the review offers recommendations for future research, emphasizing areas requiring further investigation to comprehend the full implications of these contaminants. It also suggests increased funding and support for research, development of advanced detection technologies, establishment of standardized methods, adoption of precautionary regulations, enhanced public awareness and education, cross-sectoral collaboration, and integration of scientific research into policy-making. By implementing these solutions, we can improve our ability to detect, monitor, and manage ECs, reducing environmental and public health risks.

Investigating a new approach for magnetic ionic liquids: Dispersive liquid-liquid microextraction coupled to pyrolysis gas-chromatography-mass spectrometry to determine flame retardants in sewage sludge samples

This study addresses the analysis of emerging contaminants, often using chromatographic techniques coupled to mass spectrometry. However, sample preparation is often required prior to instrumental analysis, and dispersive liquid-liquid microextraction (DLLME) is a viable strategy in this context. DLLME stands out for its ability to reduce sample and solvent volumes. Notably, dispersive liquid-liquid microextraction using magnetic ionic liquids (MILs) has gained relevance due to the incorporation of paramagnetic components in the chemical structure, thereby eliminating the centrifugation step. A pyrolizer was selected in this work to introduce sample onto the GC column, since the MIL is extremely viscous and incompatible with direct introduction through an autosampler. This study is the first to report the use of a DLLME/MIL technique for sample introduction through a pyrolizer in gas chromatography coupled to mass spectrometry (GC-MS). This approach enables the MIL to be compatible with gas chromatography systems, resulting in optimized analytical and instrument performance. The analysis of polybrominated diphenyl ether flame retardants (PBDEs) was focused on the PBDE congeners 28, 47, 99, 100, and 153 in sewage sludge samples. The [P6,6,6,14+]2[MnCl42-] MIL was thoroughly characterized using UV-Vis, Fourier transform infrared spectroscopy (FTIR), and Raman spectroscopy, as well as thermal analysis. In the chromatographic method, a pyrolyzer was used in the sample introduction step (Py-GC-MS), and critical injection settings were optimized using multivariate approaches. Optimized conditions were achieved with a temperature of 220 °C, a pyrolysis time of 0.60 min, and an injection volume of 9.00 μL. DLLME optimization was performed through central compound planning (CCD), and optimized training conditions were achieved with 10.0 mg of MIL, 3.00 μL of acetonitrile (ACN) as dispersive solvent, extraction time of 60 s, and volume of a sample of 8.50 mL. Precision was observed to range from 0.11 % to 12.5 %, with limits of detection (LOD) of 44.4 μg L-1 for PBDE 28, 16.9 μg L-1 for PBDE 47 and PBDE 99, 33.0 μg L-1 for PBDE 100 and 375 μg L-1 for PBDE 153. PBDE 28 was identified and analyzed in the sludge sample at a concentration of 800 μg L-1. The use of MIL in dispersive liquid-liquid microextraction combined with pyrolysis gas chromatography-mass spectrometry enables identification and quantification of PBDEs in sewage sludge samples at concentrations down to the µg L-1 level.

Preparation of mesoporous biogas residue biochar via a self-template strategy for efficient removal of ciprofloxacin: Effect of pyrolysis temperature

Biochar preparation and application is an anticipated pathway for the resource utilization of biogas residue. In this study, biochars were prepared by the pyrolysis of biogas residue from food waste anaerobic digestion (named as BRBCs) under various pyrolysis temperatures (300, 500, 700, and 900 °C), and the effect of pyrolysis temperatures on the physicochemical characteristics of BRBCs was examined. The adsorption performance toward ciprofloxacin (CIP), a typical antibiotic in waterbodies, was also investigated. The results showed that pyrolysis temperature significantly changed the physicochemical properties of BRBCs. In addition, the minerals in the biogas residue, especially SiO2, were rearranged to form a mesoporous structure in biochar through a self-template strategy (without activator). BRBC prepared at 900 °C exhibited a high specific surface area and pore volume, well-developed mesopore structure, and more carbon structure defects, and exhibited the largest CIP adsorption capacity with 70.29 mg g-1, which was ascribed to the combined interaction of pore diffusion, π-π interactions, hydrogen bonding, complexation, and electrostatic forces. Furthermore, the adsorption of CIP by BRBC900 was well described by two-compartment kinetic and Langmuir isotherm models. BRBC900 showed good adsorption performance toward CIP at pH 7-9. The adsorption of CIP by BRBC is a spontaneous, exothermic, entropy-increasing process. Moreover, BRBC also presented a good recycling potential. Therefore, the preparation of mesoporous biochar based on a self-template strategy not only provides an option for the resource utilization of biogas residue but also offers a new option for the treatment of antibiotic wastewater.

Knowledge graph and development hotspots of biochar as an emerging aquatic antibiotic remediator: A scientometric exploration based on VOSviewer and CiteSpace

As an emerging material in the field of environmental remediation, biochar produced by carbonisation of organic solid waste has been widely used in the remediation of antibiotic wastewater due to its environmental friendliness and excellent adsorption properties. This study analyses the current literature in the field in a comprehensive and scientific manner using CiteSpace and VOSviewer technologies. Between 2011 and 2023, a total of 1162 papers were published in this domain, spanning three distinct stages: applied methods, mechanism investigation, and enhanced improvement. The results of keyword clustering indicate that the remediation of antibiotics complexed with multiple pollutants by biochar is the main research topic, followed by the remediation of antibiotics by biochar in combination with other technologies. Furthermore, drawing from current research hotspots in antibiotic remediation using biochar, this study identified the pivotal mechanisms involved: (1) The primary mechanisms by which raw biochar remediates antibiotics include π-π electron donor-acceptor interactions, hydrophobic interactions, electrostatic interactions, hydrogen-bonding, and pore filling. (2) Steam activation, acid/base, metal salt/metal oxide, and clay mineral modification can improve the physical/chemical properties of biochar, enhancing its adsorptive removal of antibiotics. (3) Biochar activated persulfate and degraded antibiotics via free radical pathways (SO4-•, •OH and O2-•) as well as non-free radical pathways (1O2 and electron transfer). In addition, the challenge and prospect of biochar engineering applications for antibiotic remediation lies in improving the main mechanism of antibiotic remediation by biochar. The prospective utilization of biochar in enhancing the remediation of antibiotic-related pollutants holds tremendous value for the future.

Low-cost materials as vehicles for pesticides in aquatic media: a review of the current status of different biosorbents employed, optimization by RSM approach

Water contamination by pesticides is increasing dramatically due to population growth and the extensive use of pesticides in agriculture, leading to grave environmental and health concerns. Thus, efficient processes and the design and development of effective treatment technologies are required due to the enormous demand for fresh water. The adsorption approach has been widely used to remove organic contaminants such as pesticides because of its performance, less expense, high selectivity, and simplicity of operation compared to other treatment technologies. Among alternative adsorbents, biomaterials abundantly available for pesticide sorption from water resources have attracted the attention of researchers worldwide. The main objective of this review article is to (i) present studies on a wide range of raw or chemically modified biomaterials potentially effective in removing pesticides from aqueous media; (ii) indicating the effectiveness of biosorbents as green and low-cost materials for removing pesticides from wastewater; and (iii) furthermore, report the application of response surface methodology (RSM) for modeling and optimizing adsorption.

Unlocking the potential of magnetic biochar in wastewater purification: a review on the removal of bisphenol A from aqueous solution

Bisphenol A (BPA) is an essential and extensively utilized chemical compound with significant environmental and public health risks. This review critically assesses the current water purification techniques for BPA removal, emphasizing the efficacy of adsorption technology. Within this context, we probe into the synthesis of magnetic biochar (MBC) using co-precipitation, hydrothermal carbonization, mechanical ball milling, and impregnation pyrolysis as widely applied techniques. Our analysis scrutinizes the strengths and drawbacks of these techniques, with pyrolytic temperature emerging as a critical variable influencing the physicochemical properties and performance of MBC. We explored various modification techniques including oxidation, acid and alkaline modifications, element doping, surface functional modification, nanomaterial loading, and biological alteration, to overcome the drawbacks of pristine MBC, which typically exhibits reduced adsorption performance due to its magnetic medium. These modifications enhance the physicochemical properties of MBC, enabling it to efficiently adsorb contaminants from water. MBC is efficient in the removal of BPA from water. Magnetite and maghemite iron oxides are commonly used in MBC production, with MBC demonstrating effective BPA removal fitting well with Freundlich and Langmuir models. Notably, the pseudo-second-order model accurately describes BPA removal kinetics. Key adsorption mechanisms include pore filling, electrostatic attraction, hydrophobic interactions, hydrogen bonding, π-π interactions, and electron transfer surface interactions. This review provides valuable insights into BPA removal from water using MBC and suggests future research directions for real-world water purification applications.

Theoretical and Experimental Analysis of Hydroxyl and Epoxy Group Effects on Graphene Oxide Properties

In this study, we analyzed the impact of hydroxyl and epoxy groups on the properties of graphene oxide (GO) for the adsorption of methylene blue (MB) dye from water, addressing the urgent need for effective water purification methods due to industrial pollution. Employing a dual approach, we integrated experimental techniques with theoretical modeling via density functional theory (DFT) to examine the atomic structure of GO and its adsorption capabilities. The methodology encompasses a series of experiments to evaluate the performance of GO in MB dye adsorption under different conditions, including differences in pH, dye concentration, reaction temperature, and contact time, providing a comprehensive view of its effectiveness. Theoretical DFT calculations provide insights into how hydroxyl and epoxy modifications alter the electronic properties of GO, improving adsorption efficiency. The results demonstrate a significant improvement in the dye adsorption capacity of GO, attributed to the interaction between the functional groups and MB molecules. This study not only confirms the potential of GO as a superior adsorbent for water treatment, but also contributes to the optimization of GO-based materials for environmental remediation, highlighting the synergy between experimental observations and theoretical predictions in advances in materials science to improve sustainability.

Unveiling combined ecotoxicity: Interactions and impacts of engineered nanoparticles and PPCPs

Emerging contaminants such as engineered nanoparticles (ENPs), pharmaceuticals and personal care products (PPCPs) are of great concern because of their wide distribution and incomplete removal in conventional wastewater and soil treatment processes. The production and usage of ENPs and PPCPs inevitably result in their coexistence in different environmental media, thus posing various risks to organisms in aquatic and terrestrial ecosystems. However, the existing literature on the physicochemical interactions between ENPs and PPCPs and their effects on organisms is rather limited. Therefore, this paper summarized the ecotoxicity of combined ENPs and PPCPs by discussing: (1) the interactions between ENPs and PPCPs, including processes such as aggregation, adsorption, transformation, and desorption, considering the influence of environmental factors like pH, ionic strength, dissolved organic matter, and temperature; (2) the effects of these interactions on bioaccumulation, bioavailability and biotoxicity in organisms at different trophic levels; (3) the impacted of ENPs and PPCPs on cellular-level biological process. This review elucidated the potential ecological hazards associated with the interaction of ENPs and PPCPs, and serves as a foundation for future investigations into the ecotoxicity and mode of action of ENPs, PPCPs, and their co-occurring metabolites.

Enhancing Methylene Blue Removal through Adsorption and Photocatalysis-A Study on the GO/ZnTiO3/TiO2 Composite

This study focuses on synthesizing and characterizing a graphene oxide/ZnTiO3/TiO2 (GO/ZTO/TO) composite to efficiently remove methylene blue (MB) from water, presenting a novel solution to address industrial dye pollution. GO and ZTO/TO were synthesized by the modified Hummers and sol-gel methods, respectively, while GO/ZTO/TO was prepared using a hydrothermal process. The structural and surface properties of the composite were characterized using various analytical techniques confirming the integration of the constituent materials and suitability for dye adsorption. The study revealed that GO/ZTO/TO exhibits an adsorption capacity of 78 mg g-1 for MB, with only a 15% reduction in adsorption efficiency until the fifth reuse cycle. Furthermore, the study suggests optimal adsorption near neutral pH and enhanced performance at elevated temperatures, indicating an endothermic reaction. The adsorption behavior fits the Langmuir isotherm, implying monolayer adsorption on homogeneous surfaces, and follows pseudo-second-order kinetics, highlighting chemical interactions at the surface as the rate-limiting step. The photocatalytic degradation of MB by GO/ZTO/TO follows pseudo-first-order kinetics, with a higher rate constant than that of GO alone, demonstrating the enhanced photocatalytic activity of the composite. In conclusion, GO/ZTO/TO emerges as a promising and sustainable approach for water purification, through an adsorption process and subsequent photocatalytic degradation.

Environmentally safe biopolymer-clay composite for efficient adsorption of ciprofloxacin in fresh and saline solutions

In alignment with the sustainable development goals (SDGs), recent trends in water management have been directed toward using environmentally friendly bio-based materials for removing contaminants. In this work, we prepared a biocomposite of chitosan (CS) intercalated into acid activated calcium bentonite (Bent). A thermally stable mesoporous CS-Bent composite was prepared with a zeta potential of 15.5 to -34.4 mV in the pH range of 2.22-10. The biocomposite successfully removed up to 99.2% and 50 mg/g of the antibiotic ciprofloxacin HCl (CPX) at pH 5.5 via electrostatic and hydrogen bonding forces. In a multi-component aqueous system of heavy metal and CPX, the composite was more selective to CPX than to the heavy metals and removal of CPX in this system was comparable to that in a single-component system. The composite also maintained its high adsorption efficiency in NaCl solutions which makes it suitable for treating fresh and saline solutions. The combination of CS and bent produced a biodegradable eco-friendly composite characterized with good thermal and surface properties along with efficient and selective adsorption performance.

A review on carbon-based biowaste and organic polymer materials for sustainable treatment of sulfonamides from pharmaceutical wastewater

Frequent detection of sulfonamides (SAs) pharmaceuticals in wastewater has necessitated the discovery of suitable technology for their sustainable remediation. Adsorption has been widely investigated due to its effectiveness, simplicity, and availability of various adsorbent materials from natural and artificial sources. This review highlighted the potentials of carbon-based adsorbents derived from agricultural wastes such as lignocellulose, biochar, activated carbon, carbon nanotubes graphene materials as well as organic polymers such as chitosan, molecularly imprinted polymers, metal, and covalent frameworks for SAs removal from wastewater. The promising features of these materials including higher porosity, rich carbon-content, robustness, good stability as well as ease of modification have been emphasized. Thus, the materials have demonstrated excellent performance towards the SAs removal, attributed to their porous nature that provided sufficient active sites for the adsorption of SAs molecules. The modification of physico-chemical features of the materials have been discussed as efficient means for enhancing their adsorption and reusable performance. The article also proposed various interactive mechanisms for the SAs adsorption. Lastly, the prospects and challenges have been highlighted to expand the knowledge gap on the application of the materials for the sustainable removal of the SAs.

Conversion of locally available materials to biochar and activated carbon for drinking water treatment

For environmental sustainability and to achieve sustainable development goals (SDGs), drinking water treatment must be done at a reasonable cost with minimal environmental impact. Therefore, treating contaminated drinking water requires materials and approaches that are inexpensive, produced locally, and effortlessly. Hence, locally available materials and their derivatives, such as biochar (BC) and activated carbon (AC) were investigated thoroughly. Several researchers and their findings show that the application of locally accessible materials and their derivatives are capable of the adsorptive removal of organic and inorganic contaminants from drinking water. The application of locally available materials such as lignocellulosic materials/waste and its thermo-chemically derived products, including BC and AC were found effective in the treatment of contaminated drinking water. Thus, this review aims to thoroughly examine the latest developments in the use of locally accessible feedstocks for tailoring BC and AC, as well as their features and applications in the treatment of drinking water. We attempted to explain facts related to the potential mechanisms of BC and AC, such as complexation, co-precipitation, electrostatic interaction, and ion exchange to treat water, thereby achieving a risk-free remediation approach to polluted water. Additionally, this research offers guidance on creating efficient household treatment units based on the health risks associated with customized adsorbents and cost-benefit analyses. Lastly, this review work discusses the current obstacles for using locally accessible materials and their thermo-chemically produced by-products to purify drinking water, as well as the necessity for technological interventions.

Promoting the circular economy: Valorization of a residue from industrial char to activated carbon with potential environmental applications as adsorbents

Pyrolysis of residues enriched with carbon, such as in agroforestry or industrial activities, has been postulated as an emerging technology to promote the production of biofuels, contributing to the circular economy and minimizing waste. However, during the pyrolysis processes a solid fraction residue is generated. This work aims to study the viability of these chars to develop porous carbonaceous materials that can be used for environmental applications. Diverse chars discharged by an industrial pyrolysis factory have been activated with KOH. Concretely, the char residues came from the pyrolysis of olive stone, pine, and acacia splinters, spent residues fuel, and cellulose artificial casings. The changes in the textural, structural, and composition characteristics after the activation process were studied by N2 adsorption-desorption isotherms, scanning electron microscopy, FTIR, elemental analysis, and XPS. A great porosity was developed, SBET within 776-1186 m2 g-1 and pore volume of 0.37-0.59 cm3 g-1 with 70-90% of micropores contribution. The activated chars were used for the adsorption of CO2, leading to CO2 maximum uptakes of 90-130 mg g-1. There was a good correlation between the CO2 uptake with microporosity and oxygenated surface groups of the activated chars. Moreover, their ability to adsorption of contaminants in aqueous solution was also evaluated. Concretely, there was studied the adsorption of aqueous heavy metals, i.e., Cd, Cu, Ni, Pb, and Zn, and organic pollutants of emerging concern such as caffeine, diclofenac, and acetaminophen.

Adsorptive behavior of engineered biochar /hydrochar for tetracycline removal from synthetic wastewater

In this research, engineered biochar and hydrochar derived from paddy husk were compared for the adsorption tetracycline (TC) in water effluents. Biochar was produced at three different pyrolysis temperatures (e.g., 250 °C, 300 °C and 350 °C) while hydrochar was produced using three different HTC temperatures (e.g., 180 °C, 200 °C and 220 °C). The adsorptive experiments were performed for both biochar and hydrochar using well-defined experimental conditions: pH (3); initial TC concentration (10 mg/L); adsorbent dosage (1 g/L); and temperature (27 °C) to study their adsorptive performances (qe in mg/g). After selecting the best qe values for both biochar and hydrochar, both materials were modified using 20% H3PO4. A comprehensive scientific evaluation of both engineered biochar (EBC 350) and hydrochar (EHC 220) was performed using adsorption isotherm, adsorption kinetics, rate-limiting, and thermodynamics tests along with their characterization using FTIR and point of zero charge (pzc). The effects of temperature, dosage, and initial TC concentration on the adsorption process were studied for both EBC 350 and EHC 220. Acid activation improved the adsorptive performance of EHC 220 almost four times (from 1.9 to 7.5 mg/g), whereas adsorptive performance of EBC 350 improved 2.4 times from 3.8 to 9.1 mg/g. The best pH for TC adsorption onto EHC 220 was 5, whereas it was 3 for EBC 350. EBC 350 exhibited a good fit with the Freundlich model, whereas EHC 220 followed the Langmuir model. At 100 mg/L TC concentration, EHC 220 exhibited higher qe value (46.9 mg/g) compared to EBC 350 (41.7 mg/g). The Pseudo-first order kinetic model was the best fit for EHC 220 adsorption, whereas Pseudo-second order model was most suitable for EBC 350. The adsorption mechanisms involved in TC adsorption by EHC 220 included hydrogen bonding, hydrophobic effect, and π-π interaction, whereas cation exchange, mass diffusion, and π-π interaction were involved for EBC 350. The results of this study will facilitate the development of cost-effective filters with the incorporation of engineered biochar/engineered hydrochar for the active removal of emerging contaminants, like tetracycline, from wastewater so as to increase its reusable potential.

Isolation of aqueous pesticides on surface-functionalized SBA-15: glyphosate kinetics and detailed empirical insights for atrazine

Atrazine and glyphosate are two of the most used pesticides around the world causing serious water contamination. In this study, amine-functionalized Santa Barbara Amorphous-15 silica (SBA-15-NH2) was synthesized and employed for the aqueous adsorption of atrazine and glyphosate. The adsorbent was mesoporous post-functionalization with lower surface area, pore volume, size, and stability when compared to the SBA-15. The pesticides adsorption rates were high with over 85% of potential adsorption having occurred within the initial 180 min. The equilibria for atrazine and glyphosate adsorption were 60 and 360 min, respectively, and the rate data fit the fractal pseudo-second-order and pseudo-second-order models, respectively. Atrazine adsorption was higher at lower solution pH with reduced adsorption as the pH value increased. There was enhanced atrazine adsorption as temperature increased from 22 to 32 °C, but further temperature rise resulted in lower adsorption compared to that recorded at 22 °C. The processes comprise electrostatic interaction, trapping of atrazine within mesopores, and multi-layer adsorption of atrazine on surface-adsorbed atrazine. The equilibrium data fitted the Langmuir adsorption isotherm model better than the Freundlich. The SBA-15-NH2 adsorption capacity for atrazine and glyphosate was better than many adsorbents reported in literature, the adsorbent is reusable, and exhibited sustained efficiencies for atrazine that was ≥82% even after 3-cycles, an indication of chemical stability and renewability.

Industrial waste-based adsorbents as a new trend for removal of water-borne emerging contaminants

Emerging contaminants in wastewater are one of the growing concerns because of their adverse effects on human health and ecosystems. Adsorption technology offers superior performance due to its cost-effectiveness, stability, recyclability, and reliability in maintaining environmental and health standards for toxic pollutants. Despite extensive research on the use of traditional adsorbents to remove emerging contaminants, their expensiveness, lack of selectivity, and complexity of regeneration remain some of the challenges. Industrial wastes viz. blast furnace slag, red mud, and copper slag can be used to develop efficacious adsorbents for the treatment of emerging contaminants in water. Advantages of the use of such industrial wastes include resource utilization, availability, cost-effectiveness, and waste management. Nevertheless, little is known so far about their application, removal efficacy, adsorption mechanisms, and limitations in the treatment of emerging contaminants. A holistic understanding of the application of such unique industrial waste-derived adsorbents in removing emerging contaminants from water is need of the hour to transform this technology from bench-scale to pilot and large-scale applications. This review investigates different water treatment techniques associated with industrial waste-based adsorbents derived from blast furnace slag, red mud, and copper slag. Besides, this review provides important insights into the growing trends of utilizing such novel types of adsorbents to remove emerging contaminants from water with an emphasis on removal efficacy, controlling measures, adsorption mechanisms, advantages, and limitations. The present timely review brings the current state of knowledge into a single reference which could be a strong platform for future research in understanding the latest advancements, decision making, and financial management related to the treatment of wastewater using industrial waste-based adsorbents.

Preparation and Characterization of Poly(lactic acid) Membranes and Films Coated with Polyaniline for Potential Use in Environmental Remediation

This research outlines the fabrication of polymeric membranes and films of poly(lactic acid) (PLA), prepared via electrospinning and extrusion, respectively. These materials were subsequently coated with polyaniline (PANi) by using the in situ chemical polymerization technique. Scanning electron microscopy micrographs revealed that the best coatings were achieved when 3 and 30 min of contact time with the monomeric solution were used for the membrane and film, respectively. Additionally, Fourier transform infrared spectra, thermogravimetric studies, and contact angle measurements demonstrated proper interaction between PLA and PANi. The findings of these studies suggest that PLA membranes and films can serve as suitable substrates for the deposition of PANi, and the composite materials hold potential for use in environmental remediation applications.

Advances in identifying and managing emerging contaminants in aquatic ecosystems: Analytical approaches, toxicity assessment, transformation pathways, environmental fate, and remediation strategies

Emerging contaminants (ECs) are increasingly recognized as threats to human health and ecosystems. This review evaluates advanced analytical methods, particularly mass spectrometry, for detecting ECs and understanding their toxicity, transformation pathways, and environmental distribution. Our findings underscore the reliability of current techniques and the potential of upcoming methods. The adverse effects of ECs on aquatic life necessitate both in vitro and in vivo toxicity assessments. Evaluating the distribution and degradation of ECs reveals that they undergo physical, chemical, and biological transformations. Remediation strategies such as advanced oxidation, adsorption, and membrane bioreactors effectively treat EC-contaminated waters, with combinations of these techniques showing the highest efficacy. To minimize the impact of ECs, a proactive approach involving monitoring, regulations, and public education is vital. Future research should prioritize the refining of detection methods and formulation of robust policies for EC management.

Adsorption and photocatalytic applications of porphyrin-based materials for environmental separation processes: A review

As society progresses and industrializes, the issue of water pollution, caused by a wide array of organic and inorganic pollutants, poses significant risks to both human well-being and the environment. Given its distinctive characteristics, water pollution has become a paramount concern for society, necessitating immediate attention. Numerous studies have been conducted on wastewater treatment, primarily focusing on two key approaches: adsorption and photocatalytic degradation. Adsorption offers unparalleled advantages, including its simplicity, high removal efficiency, and cost-effectiveness. Conversely, photocatalysis harnesses abundant, clean, and non-polluting sunlight, addressing the critical issue of energy scarcity. Porphyrins, which are macrocyclic tetrapyrrole derivatives found widely in nature, have attracted growing interest in recent years. These lipophilic pigments exhibit remarkable chemical stability and have retained their major structural features for up to 1.1 billion years. As such, they are considered vital indicators of life and have been extensively studied, from the remnants of extinct organisms to gain insights into the principles of evolution. Porphyrins are often associated with a central metal ion within their ring system and can be modified through various substituents, including additional rings or ring opening, resulting in a wide range of functionalities. This comprehensive review summarizes recent advancements in the field of porphyrins. It begins by introducing the structures and preparation methods of porphyrins. Subsequently, it delves into notable applications of porphyrins in the context of pollutant adsorption in water and their environmentally friendly photocatalytic degradation.

Novel conjugated microporous polymers for efficient tetracycline adsorption: insights from theoretical investigations

This paper presents a detailed theoretical understanding of the noncovalent interactions between antibiotics tetracycline and conjugated microporous polymer (CMP), which is important to understand the recent experimental finding of efficient removal of antibiotics by CMP materials. We show that the co-work of π-π and H-π interactions determines the final equilibrium structures, when a tetracycline molecule spontaneously adsorbs to the surface or within the pores of the CMP network at physisorption distances. The binding energies for tetracycline/CMP systems are calculated to be -0.31 ∼ -1.15 eV, demonstrating the reliability of the adsorption. The electronic structures of CMP nanostructures remain basically undamaged upon the tetracycline adsorption. The replacement of benzothiadiazole unit with S and N heteroatoms to the phenyl moiety in the linker effectively enhanced the molecular polarity of CMP molecule and increases the interaction area between tetracycline and CMP network, consequently enhancing the average binding energies notably. Our calculations provide useful theoretical guidance for design of novel carbon-based porous adsorbents with good adsorption performance to remove residual tetracycline and other antibiotics in water.

Recent advances and future perspective on lignocellulose-based materials as adsorbents in diverse water treatment applications

The growing shortage of non-renewable resources and the burden of toxic pollutants in water have gradually become stumbling blocks in the path of sustainable human development. To this end, there has been great interest in finding renewable and environmentally friendly materials to promote environmental sustainability and combat harmful pollutants in wastewater. Of the many options, lignocellulose, as an abundant, biocompatible and renewable material, is the most attractive candidate for water remediation due to the unique physical and chemical properties of its constituents. Herein, we review the latest research advances in lignocellulose-based adsorbents, focusing on lignocellulosic composition, material modification, application of adsorbents. The modification and preparation methods of lignin, cellulose and hemicellulose and their applications in the treatment of diverse contaminated water are systematically and comprehensively presented. Also, the detailed description of the adsorption model, the adsorption mechanism and the adsorbent regeneration technique provides an excellent reference for understanding the underlying adsorption mechanism and the adsorbent recycling. Finally, the challenges and limitations of lignocellulosic adsorbents are evaluated from a practical application perspective, and future developments in the related field are discussed. In summary, this review offers rational insights to develop lignocellulose-based environmentally-friendly reactive materials for the removal of hazardous aquatic contaminants.

Graphene Oxide-Polyphenylsulfone Nanocomposite Beads for Paracetamol Removal from Aqueous Solution

This study introduces a promising and practical method for the removal of paracetamol from aqueous environments, employing graphene oxide-polymer nanocomposite beads. The approach involves the utilization of a straightforward and facile phase inversion method, offering a convenient and efficient one-step process for the creation of adsorbent beads by integrating polymers and graphene oxide (GO). The synthesized nanocomposite beads are tailored for the removal of paracetamol from simulated wastewater in batch systems. Extensive characterization techniques including XPS, FTIR, SEM, TGA, and zeta potential analysis are employed to scrutinize the chemical properties and structural attributes of the prepared beads. The investigation explores the impact of critical parameters such as adsorbent dosage, adsorption duration, initial paracetamol concentration, and solution pH on the adsorption process. These nanocomposite beads exhibit an exceptional paracetamol removal efficiency, achieving up to 99% removal. This research not only contributes to the advancement of efficient and sustainable adsorbent materials for pollutant removal but also underscores their potential for environmentally friendly and cost-effective solutions in the domain of wastewater treatment.

Construction of an allophane-based molecularly imprinted polymer for the efficient removal of antibiotic from aqueous solution

The widespread presence of ciprofloxacin (CIP) antibiotic in the water and soil poses substantial potential risks to the environment, threatening both human and animal health. In this study, we used nanoclay mineral allophane (Allo), β-cyclodextrin (β-CD) as a bifunctional monomer, and sodium alginate as a cross-linking agent, to prepare 3D porous Allo-β-CD molecularly imprinted polymers (MIPs) for the efficient removal of CIP from aqueous solution. The prepared Allo-β-CD MIP was characterized by scanning electron microscopy, transmission electron microscopy, Fourier-transform infrared spectroscopy, X-ray photoelectron spectroscopy, and zeta potential measurements. The effects of initial concentration, time, pH level, and ion concentration on CIP removal dynamics were systematically studied. The adsorption kinetics and equilibrium data of CIP were well-fitted by the pseudo-second-order kinetic model and Langmuir isotherm models, respectively. The Allo-β-CD MIP can efficiently remove CIP from an aqueous solution, with a maximal adsorption capacity of 635 mg/g. It also has impressive recyclability, and enhanced selectivity, and is widely adaptable to various environmental conditions. The adsorption mechanisms of the as-prepared adsorbent include H bonds, hydrophobic interactions, surface complexation, and n-π EDA interactions. Given the experimental evidence, as-prepared adsorbent is therefore a promising candidate for the effective removal of CIP from the aquatic environment.

Preparation and application of metal-modified biochar in the purification of micro-polystyrene polluted aqueous environment

Microplastics (MPs) have already spread across the globe and have been found in drinking water and human tissues. This may pose severe threats to human health and water environment. Therefore, this study accurately evaluated the removal effect of metal-modified biochar on polystyrene microplastics (PS-MPs) (1.0 μm) in the water environment using a high-throughput fluorescence quantification method. The results indicated that Fe-modified biochar (FeBC) and Fe/Zn-modified biochar (Fe/ZnBC) had good removal efficiencies for PS-MPs under the dosage of 3 g/L, which were 96.24% and 84.77%, respectively. Although pore effects were observed (such as "stuck", "trapped"), the electrostatic interaction was considered the main mechanism for the adsorption of PS-MPs on metal-modified biochar, whereas the formation of metal-O-PS-MPs may also contribute to the adsorption process. The removal efficiency of PS-MPs by FeBC was significantly reduced under alkaline conditions (pH = 9 and 11) or in the presence of weak acid ions (PO43-, CO32-, HCO3-). A removal efficiency of 72.39% and 78.33% of PS-MPs was achieved from tap water (TW) and lake water (LW) using FeBC when the initial concentration was 20 mg/L. However, FeBC had no removal effect on PS-MPs in biogas slurry (BS) and brewing wastewater (BW) due to the direct competitive adsorption of high concentrations of chemical oxygen demand (COD). The findings of this study highlighted that metal-modified biochar had a potential application in purifying tap water or lake water which contaminated by MPs.

Applications of covalent organic frameworks for the elimination of dyes from wastewater: A state-of-the-arts review

Covalent organic frameworks (COFs) are class of porous coordination polymers made up of organic building blocks joined together by covalent bonding through thermodynamic and controlled reversible polymerization reactions. This review discussed versatile applications of COFs for remediation of wastewater containing dyes, emphasizing the advantages of both pristine and modified materials in adsorption, membrane separation, and advanced oxidations processes. The excellent performance of COFs towards adsorption and membrane filtration has been centered to their higher crystallinity and porosity, exhibiting exceptionally high surface area, pore size and pore volumes. Thus, they provide more active sites for trapping the dye molecules. On one hand, the photocatalytic performance of the COFs was attributed to their semiconducting properties, and when coupled with other functional semiconducting materials, they achieve good mechanical and thermal stabilities, positive light response, and narrow band gap, a typical characteristic of excellent photocatalysts. As such, COFs and their composites have demonstrated excellent potentialities for the elimination of the dyes.

Advancements and sustainable strategies for the treatment and management of wastewaters from metallurgical industries: an overview

Metallurgy is pivotal for societal progress, yet it yields wastewater laden with hazardous compounds. Adhering to stringent environmental mandates, the scientific and industrial sectors are actively researching resilient treatment and disposal solutions for metallurgical effluents. The primary origins of organic pollutants within the metallurgical sector include processes such as coke quenching, steel rolling, solvent extraction, and electroplating. This article provides a detailed analysis of strategies for treating steel industry waste in wastewater treatment. Recent advancements in membrane technologies, adsorption, and various other processes for removing hazardous pollutants from steel industrial wastewater are comprehensively reviewed. The literature review reveals that advanced oxidation processes (AOPs) demonstrate superior effectiveness in eliminating persistent contaminants. However, the major challenges to their industrial-scale implementation are their cost and scalability. Additionally, it was discovered that employing a series of biological reactors instead of single-step biological processes enhances command over microbial communities and operating variables, thus boosting the efficacy of the treatment mechanism (e.g., achieving a chemical oxygen demand (COD) elimination rate of over 90%). This review seeks to conduct an in-depth examination of the current state of treating metallurgical wastewater, with a particular emphasis on strategies for pollutant removal. These pollutants exhibit distinct features influenced by the technologies and workflows unique to their respective processes, including factors such as their composition, physicochemical properties, and concentrations. Therefore, it is of utmost importance for customized treatment and disposal approaches, which are the central focus of this review. In this context, we will explore these methods, highlighting their advantages and characteristics.

Water, Water Everywhere, but Every Drop Unique: Challenges in the Science to Understand the Role of Contaminants of Emerging Concern in the Management of Drinking Water Supplies

The protection and management of water resources continues to be challenged by multiple and ongoing factors such as shifts in demographic, social, economic, and public health requirements. Physical limitations placed on access to potable supplies include natural and human-caused factors such as aquifer depletion, aging infrastructure, saltwater intrusion, floods, and drought. These factors, although varying in magnitude, spatial extent, and timing, can exacerbate the potential for contaminants of concern (CECs) to be present in sources of drinking water, infrastructure, premise plumbing and associated tap water. This monograph examines how current and emerging scientific efforts and technologies increase our understanding of the range of CECs and drinking water issues facing current and future populations. It is not intended to be read in one sitting, but is instead a starting point for scientists wanting to learn more about the issues surrounding CECs. This text discusses the topical evolution CECs over time (Section 1), improvements in measuring chemical and microbial CECs, through both analysis of concentration and toxicity (Section 2) and modeling CEC exposure and fate (Section 3), forms of treatment effective at removing chemical and microbial CECs (Section 4), and potential for human health impacts from exposure to CECs (Section 5). The paper concludes with how changes to water quantity, both scarcity and surpluses, could affect water quality (Section 6). Taken together, these sections document the past 25 years of CEC research and the regulatory response to these contaminants, the current work to identify and monitor CECs and mitigate exposure, and the challenges facing the future.

A mini review of recent progress in the removal of emerging contaminants from pharmaceutical waste using various adsorbents

The presence of emerging contaminants (ECs) originating from pharmaceutical waste in water, wastewater, and marine ecosystems at various geographical locations has been clearly publicised. This review paper presents an overview of current monitoring data on the occurrences and distributions of ECs in coastal ecosystem, tap water, surface water, ground water, treated sewage effluents, and other sources. Technological advancements for EC removal are also presented, which include physical, chemical, biological, and hybrid treatments. Adsorption remains the most effective method to remove ECs from water bodies. Various types of adsorbents, such as activated carbons, biochars, nanoadsorbents (carbon nanotubes and graphene), ordered mesoporous carbons, molecular imprinting polymers, clays, zeolites, and metal-organic frameworks have been extensively used for removing ECs from water sources and wastewater. Extensive findings on adsorptive performances, process efficiency, reusability properties, and other related information are thoroughly discussed in this mini review.

Sustainable removal of phenol from wastewater using a biopolymer hydrogel adsorbent comprising crosslinked chitosan and κ-carrageenan

A biopolymer-based adsorbent comprising chitosan (CS) and κ-carrageenan (κ-Carr) was synthesised and evaluated to treat phenolic-contaminated water. The developed CS/κ-Carr hydrogel demonstrated excellent performance with a phenol adsorption uptake of 80 %. The morphologies of CS/κ-Carr hydrogels with different ratios of CS to κ-Carr ranging from 1:2 to 7:3 were characterised using scanning electron microscopy and atomic force microscopy; their chemical structures were investigated by spectral analyses using Fourier-transform infrared spectroscopy, thermogravimetric analysis, and differential scanning calorimetry; their adsorption characteristics were determined using tests for swelling, chemical stability, hygroscopic moisture content, and hydrophilicity. Finally, a batch-type evaluation method demonstrated adsorption performance at 25 °C and pH 6.9. Adsorption isotherms and kinetic data were successfully obtained using the Freundlich and pseudo-second-order models, respectively. The results indicate that one-pot synthesis of an insoluble CS/κ-Carr hydrogel adsorbent exhibits considerable potential for the removal of phenol from aqueous solutions, providing an environmentally friendly technology enhancing the phenol adsorption performance of CS.

Spring water quality monitoring using multiple bioindicators from multiple collection sites

The aim of this study was to examine the water quality of the Extrema River spring in a Brazilian Cerrado area. Three collection sites (P1 - P3) were sampled in the dry and rainy seasons, which are close to industries from different sectors. In the physicochemical analysis, a decrease in dissolved oxygen levels (<5 mg/L) and pH (< 6) at P3 was detected. An increase in heterotrophic bacteria count was recorded at all sites (> 500 colonies/ml). In ecotoxicological analyses, P2 and P3 exhibited toxicity using Vibrio fischeri (> 20%). In evaluating toxicity, the reduction in seed germination was significant utilizing Lactuca sativa at all locations and with Allium cepa only at P2; rootlet length was decreased at P3 on L. sativa and at all sites with A. cepa. In contrast, loss of membrane integrity and mitochondrial function of meristems was adversely affected at all locations using both L. sativa and A. cepa assays. Principal components analysis (PCA) approach indicated that seasonality apparently did not markedly interfere with the obtained data, but it is important to include more collection locations to be evaluated with multiple bioindicators in the spring region. Our data indicate the urgent need for more rigorous programs to monitor the discharge of effluents into water springs.

Effect of Dietary Selenium on the Growth and Immune Systems of Fish

Dietary selenium (Se) is an essential component that supports fish growth and the immune system. This review attempts to provide insight into the biological impacts of dietary Se, including immunological responses, infection defense, and fish species growth, and it also identifies the routes via which it enters the aquatic environment. Dietary Se is important in fish feed due to its additive, antioxidant, and enzyme properties, which aid in various biological processes. However, excessive intake of it may harm aquatic ecosystems and potentially disrupt the food chain. This review explores the diverse natures of dietary Se, their impact on fish species, and the biological methods for eliminating excesses in aquatic environments. Soil has a potential role in the distribution of Se through erosion from agricultural, industrial, and mine sites. The research on dietary Se's effects on fish immune system and growth can provide knowledge regarding fish health, fish farming strategies, and the health of aquatic ecosystems, promoting the feed industry and sustainable aquaculture. This review provides data and references from various research studies on managing Se levels in aquatic ecosystems, promoting fish conservation, and utilizing Se in farmed fish diets.

Perchlorate and chlorate assessment in drinking water in northern Chilean cities

Perchlorate and chlorate are endocrine disruptors considered emerging contaminants (ECs). Both oxyanions are commonly associated with anthropogenic contamination from fertilizers, pesticides, explosives, and disinfection byproducts. However, the soils of the Atacama Desert are the most extensive natural reservoirs of perchlorate in the world, compromising drinking water sources in northern Chile. Field campaigns were carried (2014-2018) to assess the presence of these ECs in the water supply networks of twelve Chilean cities. Additionally, the occurrence of perchlorate, chlorate and other anions typically observed in drinking water matrices of the Atacama Desert (i.e., nitrate, chloride, sulfate) was evaluated using a Spearman correlation analysis to determine predictors for perchlorate and chlorate. High concentrations of perchlorate (up to 114.48 μg L-1) and chlorate (up to 9650 μg L-1) were found in three northern cities. Spatial heterogeneities were observed in the physicochemical properties and anion concentrations of the water supply network. Spearman correlation analysis indicated that nitrate, chloride, and sulfate were not useful predictors for the presence of perchlorate and chlorate in drinking water in Chile. Hence, this study highlights the need to establish systematic monitoring, regulation, and treatment for these EC of drinking water sources in northern Chilean cities for public health protection.

Self-Assembled Chitosan/Dialdehyde Carboxymethyl Cellulose Hydrogels: Preparation and Application in the Removal of Complex Fungicide Formulations from Aqueous Media

Environmental contamination with pesticides occurs at a global scale as a result of prolonged usage and, therefore, their removal by low-cost and environmentally friendly systems is actively demanded. In this context, our study was directed to investigate the feasibility of using some self-assembled hydrogels, comprising chitosan (CS) and carboxymethylcellulose (CMC) or dialdehyde (DA)-CMC, for the removal of four complex fungicide formulations, namely Melody Compact (MC), Dithane (Dt), Curzate Manox (CM), and Cabrio®Top (CT). Porous CS/CMC and CS/DA-CMC hydrogels were prepared as discs by combining the semi-dissolution acidification sol-gel transition method with a freeze-drying approach. The obtained CS/CMC and CS/DA-CMC hydrogels were characterized by gel fraction yield, FTIR, SEM, swelling kinetics, and uniaxial compression tests. The batch-sorption studies indicated that the fungicides' removal efficiency (RE%) by the CS/CMC hydrogels was increased significantly with increasing sorbent doses reaching 94%, 93%, 66% and 48% for MC, Dt, CM and CT, respectively, at 0.2 g sorbent dose. The RE values were higher for the hydrogels prepared using DA-CMC than for those prepared using non-oxidized CMC when initial fungicide concentrations of 300 mg/L or 400 mg/L were used. Our results indicated that CS/DA-CMC hydrogels could be promising biosorbents for mitigating pesticide contamination of aqueous environments.

A comprehensive review of coconut-based porous materials for wastewater treatment and CO2 capture

For several decades, water pollution has become a major threat to aquatic and non-aquatic species, including humans. Different treatment techniques have already been proposed and implemented depending on wastewater characteristics. But many of these treatment techniques are expensive and inefficient. Adsorption-based techniques have shown impressive performances as an inexpensive treatment method previously. Coconut-based resources have been considered as adsorbents for wastewater treatment because of their abundance, low cost, and favorable surface properties. However, over the last decade, no comprehensive study has been published regarding biochar from coconut-based materials for wastewater treatment and CO2 capture. This review discusses biochar production technology for coconut-based materials, its modification and characterization, its utilization as an adsorbent for removing metals and organics from wastewater, and the associated removal mechanisms and the economic aspects of coconut-based biochar. Coconut-based materials are cheap and effective for removing various organic compounds such as pesticides, hormones, phenol, and phenolic compounds from solutions and capturing CO2 from air mainly through the pore-filling mechanism. Utilizing coconut-based biochars in a hybrid system that combines adsorption and other techniques, such as biotechnology or chemical coagulation is a promising way to increase their performance as an adsorbent in wastewater treatment.

Aquatic toxicity of hydroquinone and catechol following metal oxide treatment to Ceriodaphnia dubia and Pimephales promelas

Metal oxides comprise a large group of chemicals used in water treatment to adsorb organic pollutants. The ability of titanium dioxide (TiO₂) and iron (III) oxide (Fe₂O₃) to reduce the chronic toxicity of (phenolic) C₆H₆(OH)₂ isomers, namely hydroquinone (HQ) and catechol (CAT) to Ceriodaphnia dubia and Pimephales promelas (less than 24 h-old) were investigated. The toxic endpoints following metal oxide treatment were compared to endpoints of untreated CAT and HQ. In chronic toxicity testing, HQ resulted in greater toxicity than CAT for both test organisms; the median lethal concentrations (LC₅₀) for CAT were 3.66 to 12.36 mg.L^-1 for C. dubia and P. promelas, respectively, while LC₅₀ for HQ were 0.07 to 0.05 mg.L^-1, respectively. Although both treated solutions presented lower toxic endpoints than those in the untreated solutions, Fe₂O₃ had a better potential to reduce the toxic effects of CAT and HQ than TiO₂.

Adsorption of Omeprazole on Biobased Adsorbents Doped with Si/Mg: Kinetic, Equilibrium, and Thermodynamic Studies

This paper proposes an easy and sustainable method to prepare high-sorption capacity biobased adsorbents from wood waste. A biomass wood waste (spruce bark) was employed to fabricate a composite doped with Si and Mg and applied to adsorb an emerging contaminant (Omeprezole) from aqueous solutions, as well as synthetic effluents loaded with several emerging contaminants. The effects of Si and Mg doping on the biobased material's physicochemical properties and adsorptive performance were evaluated. Si and Mg did not influence the specific surface area values but impacted the presence of the higher number of mesopores. The kinetic and equilibrium data presented the best fitness by the Avrami Fractional order (AFO) and Liu isotherm models, respectively. The values of Q_max ranged from 72.70 to 110.2 mg g^-1 (BP) and from 107.6 to 249.0 mg g^-1 (BTM). The kinetic was faster for Si/Mg-doped carbon adsorbent, possibly due to different chemical features provoked by the doping process. The thermodynamic data showed that the adsorption of OME on biobased adsorbents was spontaneous and favorable at four studied temperatures (283, 293, 298, 303, 308, 313, and 318 K), with the magnitude of the adsorption correspondent to a physical adsorption process (ΔH° < 2 kJ mol^-1). The adsorbents were applied to treat synthetic hospital effluents and exhibited a high percentage of removal (up to 62%). The results of this work show that the composite between spruce bark biomass and Si/Mg was an efficient adsorbent for OME removal. Therefore, this study can help open new strategies for developing sustainable and effective adsorbents to tackle water pollution.

Impregnation of biochar with montmorillonite and its activation for the removal of azithromycin from aqueous media

An inexpensive and environmentally friendly composite synthesized from rice husk, impregnated with montmorillonite and activated by carbon dioxide, was investigated for the removal of azithromycin from an aqueous solution. Various techniques were used to characterize adsorbents in detail. The sorption process was primarily regulated by the solution pH, pollutant concentration, contact duration, adsorbent dose, and solution temperature. The equilibrium data were best analyzed using the nonlinear Langmuir and Sips (R² > 0.97) isotherms, which revealed that adsorption occurs in a homogenous manner. The adsorption capacity of pristine biochar and carbon dioxide activated biochar-montmorillonite composite was 33.4 mg g^-1 and 44.73 mg g^-1, respectively. Kinetic studies identified that the experimental data obeyed the pseudo-second-order and Elovich models (R² > 0.98) indicating the chemisorption nature of adsorbents. The thermodynamic parameters determined the endothermic and spontaneous nature of the reaction. The ion exchange, π-π electron-donor-acceptor (EDA) interactions, hydrogen-bonding, and electrostatic interactions were the plausible mechanisms responsible for the adsorption process. This study revealed that a carbon dioxide activated biochar-montmorillonite composite may be used as an effective, sustainable, and economical adsorbent for the removal of azithromycin from polluted water.

Remediation of environmental toxicants using carbonaceous materials: opportunity and challenges

Adsorption and photocatalytic properties of carbonaceous materials, viz., carbon nanotubes (CNTs), fullerene, graphene, graphene oxide, carbon nanofiber nanospheres, and activated carbon, are the legitimate weapons for the remediation of emerging and persistent inorganic/organic contaminants, heavy metals, and radionucleotides from the environment. High surface area, low or non-toxic nature, ease of synthesis, regeneration, and chemical modification of carbonaceous material make them ideal for the removal of toxicants. The research techniques investigated during the last decade for the elimination of environmental toxicants using carbonaceous materials are reviewed to offer comprehensive insight into the mechanism, efficiency, applications, advantages, and shortcomings. Opportunities and challenges associated with carbon materials have been discussed to suggest future perspectives in the remediation of environmental toxicants.

Insight into the adsorptive removal of ibuprofen using porous carbonaceous materials: A review

Over the last decade, the removal of pharmaceuticals from aquatic bodies has garnered substantial attention from the scientific community. Ibuprofen (IBP), a non-steroidal anti-inflammatory drug, is released into the environment in pharmaceutical waste as well as medical, hospital, and household effluents. Adsorption technology is a highly efficient approach to reduce the IBP in the aquatic environment, particularly at low IBP concentrations. Due to the exceptional surface properties of carbonaceous materials, they are considered ideal adsorbents for the IBP removal of, with high binding capacity. Given the importance of the topic, the adsorptive removal of IBP from effluent using various carbonaceous adsorbents, including activated carbon, biochar, graphene-based materials, and carbon nanostructures, has been compiled and critically reviewed. Furthermore, the adsorption behavior, binding mechanisms, the most effective parameters, thermodynamics, and regeneration methods as well as the cost analysis were comprehensively reviewed for modified and unmodified carbonaceous adsorbents. The compiled studies on the IBP adsorption shows that the IBP uptake of some carbon-based adsorbents is significantly than that of commercial activated carbons. In the future, much attention is needed for practical utilization and upscaling of the research findings to aid the management and sustainability of water resource.

Magnetically Guided Synthesis of Anisotropic Porous Carbons toward Efficient CO2 Capture and Magnetic Separation of Oil

Conventional synthetic strategies do not allow one to impart structural anisotropy into porous carbons, thus leading to limited control over their textural properties. While structural anisotropy alters the mechanical properties of materials, it also introduces an additional degree of directionality to increase the pore connectivity and thus the flux in the designed direction. Accordingly, in this work the structure of porous carbons prepared from resorcinol-formaldehyde gels has been rendered anisotropic by integrating superparamagnetic colloids to the sol-gel precursor solution and by applying a uniform magnetic field during the sol-gel transition, which enables the self-assembly of magnetic colloids into chainlike structures to template the growth of the gel phase. Notably, the anisotropic pore structure is maintained upon pyrolysis of the gel, leading to hierarchically porous carbon monoliths with tunable structure and porosities. With an advantage granted to anisotropic materials, these porous carbons showed higher porosity, a higher CO₂ uptake capacity of 3.45 mmol g^-1 at 273 K at 1.1 bar, and faster adsorption kinetics compared to the ones synthesized in the absence of magnetic field. Moreover, these materials were also used as magnetic sorbents with fast adsorption kinetics for efficient oil-spill cleanup and retrieved easily by using an external magnetic field.

New trajectories of technologies for the removal of pollutants and emerging contaminants in the environment

Modern society has increasingly a diffusion of pollutants and emerging contaminants (e.g., different types of chemicals and endocrine disruptors in pharmaceuticals, pesticides, household cleaning, and personal care products, etc.) that have detrimental effects on the environment (atmosphere, hydrosphere, biosphere and anthroposphere) and also generate diseases and disorders on the people health. Environmental science requires efforts in the detection and elimination of manifold pollutants and emerging pollutants with appropriate product and process technologies. This study aims to analyze different paths of treatment technologies to investigate their evolution and predict new directions of promising technological trajectories to support the removal of contaminants directed to reach, whenever possible, sustainable development objectives. The work is mainly devoted to wastewater treatment technologies. A proposed model analyzes the evolution of patents (proxy of innovation and new technology) on publications (proxy of science and knowledge advances) to quantify the relative growth rate of new trajectories of technologies to remove pollutants and emerging contaminants. Results reveal that new directions of treatment technologies having an accelerated rate of growth are (in decreasing order): biochar and reverse osmosis in physical-based technologies, coagulation, and disinfection water treatments in chemical-based technologies and anaerobic processes in biological-based technologies. Other main technologies, such as carbon nanotubes and advanced oxidation processes, seem to be in the initial phase of development and need learning by using processes and further science and technology advances to be implemented as effective treatments and cost-effective. The results here are in accord with global water and wastewater equipment treatment market revenues by technology, showing a similar trend. These findings bring us to the main information to extend the knowledge about new directions of technologies for the treatment and/or elimination of pollutants and microorganisms that can support decisions of policymakers towards goals of sustainable development by reducing environmental degradation and people health disorders.

Catalytic degradation of dimethomorph by nitrogen-doped rice husk biochar

N-doped biochar is widely used for activating persulfate to degrade organic pollutants. Which type of N atom is the key factor for activation is still unclear and needs to be further explored and analyzed. In this study, four kinds of biochar were prepared using urea and rice husk as precursors, and tested for the catalytic degradation of dimethomorph. Increasing the nitrogen doping level caused the catalytic removal efficiency of dimethomorph in the presence of peroxymonosulfate increased from 16.6% to 86.8%. A correlation analysis showed that the ability of N-doped biochar to activate PMS is mainly related to the content of pyrrole N, graphite N and carbonyl and the degree of defects. In experiments on electron paramagnetic resonance and free radical suppression, the reactive species of SO₄^•-, ¹O₂,·OH and O₂^.- were detected, among which ¹O₂ was found to be the main agent in the nonradical pathway. The degradation pathways for dimethomorph were analyzed based on a total of 8 degradation products identified by high-performance liquid chromatography-time of flight mass spectrometry (HPLC-Q-TOFMS). The results of this study provide a fundamental basis for using agricultural waste to produce inexpensive and efficient nonmetal catalysts that are highly effective in reducing dimethomorph levels in agricultural lands.

Preparation of Nanocellulose-Based Aerogel and Its Research Progress in Wastewater Treatment

Nowadays, the fast expansion of the economy and industry results in a considerable volume of wastewater being released, severely affecting water quality and the environment. It has a significant influence on the biological environment, both terrestrial and aquatic plant and animal life, and human health. Therefore, wastewater treatment is a global issue of great concern. Nanocellulose's hydrophilicity, easy surface modification, rich functional groups, and biocompatibility make it a candidate material for the preparation of aerogels. The third generation of aerogel is a nanocellulose-based aerogel. It has unique advantages such as a high specific surface area, a three-dimensional structure, is biodegradable, has a low density, has high porosity, and is renewable. It has the opportunity to replace traditional adsorbents (activated carbon, activated zeolite, etc.). This paper reviews the fabrication of nanocellulose-based aerogels. The preparation process is divided into four main steps: the preparation of nanocellulose, gelation of nanocellulose, solvent replacement of nanocellulose wet gel, and drying of nanocellulose wet aerogel. Furthermore, the research progress of the application of nanocellulose-based aerogels in the adsorption of dyes, heavy metal ions, antibiotics, organic solvents, and oil-water separation is reviewed. Finally, the development prospects and future challenges of nanocellulose-based aerogels are discussed.

Tailored Sky-Parking Architectures of 3D Graphene Oxide Towards Highly-Efficient Water Purification

The widespread use of chemicals has brought serious water pollution threatening human health and environment, which requires green, fast, and low-cost purification urgently. Here, we build up a novel material family of sky-parking-like 3D structured graphene oxides (SP-GOs) with adjustable interlayer-space of 0.8-1.7 nm via the insertion of different sized diamine compounds as support pillars between GO layers. The assembled 3D SP-GOs exhibit superior adsorption capacity and short removal time for various aromatic organic compounds in water, achieving record-breaking maximum adsorption capacity of 535.79 mg g^-1 toward the most common water-pollutant bisphenol A (BPA) at ambient conditions as well as significantly improved removal of other organic pollutants including sulfapyridine, carbamazepine, ketoprofen and 2-naphthol. The construction of SP-GO provides a simple approach for evolving the GO material from 2D to 3D and a new avenue for the decontamination of pollutants in environmental remediation.

Engineering sodium alginate-SiO2 composite beads for efficient removal of methylene blue from water

The lack of sufficient active binding sites in commonly reported sodium alginate (SA)-based porous beads hampers their performances in adsorption of water contaminants. To address this problem, porous SA-SiO₂ beads functionalized with poly(2-acrylamido-2-methylpropane sulfonic acid) (PAMPS) are reported in this work. Due to the porous properties and the existence of abundant sulfonate groups, the obtained composite material SA-SiO₂-PAMPS shows excellent adsorption capacity toward cationic dye methylene blue (MB). The adsorption kinetic and adsorption isotherm studies reveal that the adsorption process fits closely to pseudo-second-order kinetic model and Langmuir isotherm model, respectively, suggesting the existence of chemical adsorption and monolayer adsorption behavior. The maximum adsorption capacity obtained from Langmuir model is found to be 427.36, 495.05, and 564.97 mg/g under 25, 35, and 45 °C, respectively. The calculated thermodynamic parameters indicate that MB adsorption on SA-SiO₂-PAMPS is spontaneous and endothermic.

β-Cyclodextrin functionalized adsorbents for removal of organic micropollutants from water

The presence of organic micropollutants in water is an ongoing concern due to the potential risks to living organisms. β-Cyclodextrin-based adsorbents have been developed to remove organic micropollutants from water as they are deemed to be efficient, selective and reusable. This literature review establishes the current state of the knowledge on the application of β-Cyclodextrin adsorbents for the removal of organic micropollutants from water and determines knowledge gaps and recommendations for future studies. An inventory of organic micropollutants that have been studied was developed and it revealed that bisphenol-A has been the most commonly studied. Adsorbent configurations were reviewed and modifications to the adsorbent structures that have provided enhanced adsorption properties were identified. The size and shape of the organic micropollutants was found to affect the adsorption behavior. The surface charge of β-Cyclodextrin adsorbents influence adsorption when repulsive forces are present and the extent of repulsion can depend on the pH of the solution. Common competitors such as natural organic matter and inorganic ions do not significantly impact the adsorption of organic micropollutants however relatively small fulvic acids may compete for the β-Cyclodextrin cavity depending on the adsorbent type. Desorption of organic micropollutants from these adsorbents has been accomplished with alcohols and most adsorbents have been recovered and reused in adsorption/desorption cycles. The need for enhanced recovery processes that maintain water quality and adsorbent integrity was identified. The use of quantitative structure-activity relationships and molecular computational tools could potentially guide future environmental applications of β-Cyclodextrin adsorbents.

Multifunctional Cross-Linked Shrimp Waste-Derived Chitosan/MgAl-LDH Composite for Removal of As(V) from Wastewater and Antibacterial Activity

This work synthesized a novel chitosan-loaded MgAl-LDH (LDH = layered double hyroxide) nanocomposite, which was physicochemically characterized, and its performance in As(V) removal and antimicrobial activity was evaluated. Chitosan-loaded MgAl-LDH nanocomposite (CsC@MgAl-LDH) was prepared using cross-linked natural chitosan from shrimp waste and modified by Mg-Al. The main mechanisms predominating the separation of As(V) were elucidated. The characteristic changes confirming MgAl-LDH modification with chitosan were analyzed through Fourier transform infrared spectroscopy, X-ray diffraction, thermogravimetric analysis-differential thermal analysis, and Brunauer-Emmett-Teller measurements. Porosity and the increased surface area play an important role in arsenic adsorption and microbial activity. Adsorption kinetics follows the general order statistically confirmed by Bayesian Information Criterion differences. To understand the adsorption process, Langmuir, Freundlich, and Liu isotherms were studied at three different temperatures. It was found that Liu's isotherm model was the best-fitted model. CsC@MgAl-LDH showed the maximum adsorption capacity of 69.29 mg g^-1 toward arsenic at 60 °C. It was observed that the adsorption capacity of the material rose with the increase in temperature. The spontaneous behavior and endothermic nature of adsorption was confirmed by the thermodynamic parameters study. Minimal change in percentage removal was observed with coexisting ions. The regeneration of material and adsorption-desorption cycles revealed that the adsorbent is economically efficient. The nanocomposite was very effective against Staphylococcus aureus and Bacillus subtilus.

Porous Materials for Water Purification

Water pollution is a growing threat to humanity due to the pervasiveness of contaminants in water bodies. Significant efforts have been made to separate these hazardous components to purify polluted water through various methods. However, conventional remediation methods suffer from limitations such as low uptake capacity or selectivity, and current water quality standards cannot be met. Recently, advanced porous materials (APMs) have shown promise in improved segregation of contaminants compared to traditional porous materials in uptake capacity and selectivity. These materials feature merits of high surface area and versatile functionality, rendering them ideal platforms for the design of novel adsorbents. This Review summarizes the development and employment of APMs in a variety of water treatments accompanied by assessments of task-specific adsorption performance. Finally, we discuss our perspectives on future opportunities for APMs in water purification.

Experimental investigation for treating ibuprofen and triclosan by biosurfactant from domestic wastewater

The presence of emerging pollutants of pharmaceutical products and personal care products (PPCPs) in the aquatic environment overspreads the threat on living beings. Bioremediation is a promising option for treating wastewater. In the present study, an experimental investigation was carried out to produce a biosurfactant by Pseudomonas aeruginosa (MTCC 1688) for the removal of Ibuprofen (IBU) and Triclosan (TCS) from domestic wastewater. It was performed in three stages. Firstly, the production and optimization of biosurfactant was carried out to arrive at the best combination of crude sunflower oil, sucrose and ammonium bicarbonate (10%: 5.5 g/L: 1 g/L) to yield effective biosurfactant production (crude biosurfactant) and further extended to achieve critical micelle concentration (CMC) formation by dilution (biosurfactant at 10.5%). The stability of the biosurfactant was also confirmed. Biosurfactant showed a reduction in the surface tension to 41 mN/m with a yield concentration of 11.2 g/L. Secondly, its effectiveness was evaluated for the removal of IBU and TCS from the domestic wastewater collected during the dry and rainy seasons. Complete removal of IBU was achieved at 36 h & 6 h and TCS at 6 h & 1 h by crude biosurfactant and biosurfactant at CMC formation for the dry season sample. IBU removal was achieved in 2 h by both crude and biosurfactant at CMC and no TCS was detected in the rainy season sample. Thirdly, biotransformation intermediates of IBU and TCS formed during the application of the biosurfactant and degradation pathways are proposed based on the Liquid Chromatography-Mass Spectrometry (LC-MS) and it indicates that there is no formation of toxic by-products. Based on the results, it is evident that biosurfactant at CMC has performed better for the removal of IBU and TCS than crude biosurfactants without any formation of toxic intermediates. Hence, this study proved to be an eco-friendly, cost-effective and sustainable treatment option for domestic wastewater treatment.