Occurrence, fate and risk assessment of parabens and their chlorinated derivatives in an advanced wastewater treatment plant

Solar-driven environmental fate of chlorinated parabens in natural and engineered water systems

Parabens are classified as emerging contaminants in global waters, and the ubiquitous emergence of their high-risk chlorinated products generated from chlorine-based wastewater disinfection has attracted increasing attention. However, rather limited information is available on their photofate after discharging into surface waters, and their degradation behavior after solar-based engineering water treatment is unclear. Herein, the reactivity of four chlorinated parabens with different photochemically produced reactive intermediates was measured. Quantitative contribution analysis in abating such compounds showed the dominance of direct photolysis in sunlit natural freshwaters. Introducing a technical solar/peroxymonosulfate (PMS) system could greatly improve the removal of chlorinated parabens. The economic analysis suggested that chlorinated parabens exhibited a minimum value of economic input as 93.41-158.04 kWh m-3 order-1 at 0.543-0.950 mM PMS. The high-resolution mass spectrometry analysis of the degradation products suggested that dechlorination, hydroxylation, and ester chain cleavage were the dominant transformation pathways during photolysis and solar/PMS treatment. Furthermore, the in silico prediction indicated severe aquatic toxicity of certain products but enhanced biodegradability. Overall, this investigation filled a knowledge gap on the reactivity of chlorinated parabens with diverse reactive transients and their quantitative contributions to the photolysis and solar/PMS treatment of emerging micropollutants in water.

Complete genome sequence of the 4-hydroxybenzoate-degrading bacterium Gymnodinialimonas sp. 57CJ19, a potential novel species from intertidal sediments

A bacterium Gymnodinialimonas sp. 57CJ19, was isolated from the intertidal sediments of Aoshan Bay, and further assays showed that it has the ability to degrade the antibacterial preservative 4-hydroxybenzoate. The complete genome sequence was sequenced, and phylogenomic analyses indicated that strain 57CJ19 represents a potential novel species in the genus Gymnodinialimonas (family Rhodobacteraceae). Its genome contains a 3,861,607-bp circular chromosome with 61.25% G + C content. Gene prediction revealed 3716 protein-encoding genes, 41 tRNA genes, 3 rrn operons, and 3 non-coding RNA genes. Functional annotation revealed a complete metabolic pathway for 4-hydroxybenzoate. The genome sequence of strain 57CJ19 provides new insights into the potential and underlying genomic basis of aromatic compound pollutant degradation by marine bacteria.

Accumulation of Parabens, Their Metabolites, and Halogenated Byproducts in Migratory Birds of Prey: A Comparative Study in Texas and North Carolina, USA

Parabens are alkyl esters of p-hydroxybenzoic acid that are commonly used as preservatives in personal care products such as cosmetics. Recent studies have revealed the presence of parabens in surface and tap water because of their use as disinfection products; however, little is known about their occurrence in biological samples and their bioaccumulation potential, particularly in raptor birds known as sentinels for pollutant detection. We examined the occurrence and tissue distribution of parabens, their metabolites, and halogenated byproducts in the liver, kidney, brain, and muscle of birds of prey from Texas and North Carolina (USA). Methylparaben (MeP), propylparaben (PrP), and butylparaben (BuP) were detected in more than 50% of all tissues examined, with the kidney exhibiting the highest concentration of MeP (0.65-6.84 ng/g wet wt). Para-hydroxybenzoic acid (PHBA), a primary metabolite, had the highest detection frequency (>50%) and a high accumulation range in the liver, of 4.64 to 12.55 ng/g. The chlorinated compounds chloromethylparaben and chloroethylparaben were found in over half of the tissues, of which dichloromethylparaben (2.20-3.99 ng/g) and dichloroethylparaben (1.01-5.95 ng/g) in the kidney exhibited the highest concentrations. The dibrominated derivatives dibromideethylparaben (Br2EtP) was detected in more than 50% of samples, particularly in muscle and brain. Concentrations in the range of 0.14 to 17.38 ng/g of Br2EtP were detected in the kidney. Dibromidepropylparaben (Br2PrP) was not frequently detected, but concentrations ranged from 0.09 to 21.70 ng/g in muscle. The accumulations of total amounts (sum) of parent parabens (∑P), metabolites (∑M), and halogenated byproducts (∑H) in different species were not significantly different, but their distribution in tissues differed among the species. Positive correlations were observed among MeP, PrP, BuP, and PHBA in the liver, suggesting similar origins and metabolic pathways. Environ Toxicol Chem 2024;00:1-12. © 2024 The Author(s). Environmental Toxicology and Chemistry published by Wiley Periodicals LLC on behalf of SETAC.

Enhanced oxidation of parabens in an aqueous solution by air-assisted cold plasma

Various contaminants of emerging concern (CECs) including pharmaceuticals and personal care products (PPCPs) have been known to threaten the aquatic ecosystem and human health even at low levels in surface water. Among them, the wide variety use of parabens as preservatives may pose potential threat to human because parabens may present estrogenic activity. Various advanced oxidation processes have been attempted to reduce parabens, but challenges using cold plasma (CP) are very rare. CP is worth paying attention to in reducing parabens because it has the advantage of generating radical ions, including reactive oxygen/nitrogen species and various ions. Accordingly, this study demonstrates how CP can be utilized and how CP competes with other advanced oxidation processes in energy requirements. Quantified ethyl-, propyl-, and butyl-paraben indicate that CP can effectively degrade them up to 99.1% within 3 h. Regression reveals that the kinetic coefficients of degradation can be increased to as high as 0.0328 min-1, comparable to other advanced oxidation processes. Many by-products generated from the oxidation of parabens provide evidence of the potential degradation pathway through CP treatment. In addition, we found that the electrical energy consumption per order of CP (39-95 kWh/m3/order) is superior to other advanced oxidation processes (69∼31,716 kWh/m3/order). Overall, these results suggest that CP may be a viable option to prevent adverse health-related consequences associated with parabens in receiving water.

Anaerobic co-metabolic biodegradation of pharmaceuticals and personal care products driven by glycerol fermentation

Anaerobic digestion in two sequential phases, acidogenesis and methanogenesis, has been shown to be beneficial for enhancing the biomethane generation from wastewater. In this work, the application of glycerol (GOH) as a fermentation co-substrate during the wastewater treatment was evaluated on the biodegradation of different pharmaceuticals and personal care products (PPCPs). GOH co-digestion during acidogenesis led to a significant increase in the biodegradation of acetaminophen (from 78 to 89%), ciprofloxacin (from 25 to 46%), naproxen (from 73 to 86%), diclofenac (from 36 to 48%), ibuprofen (from 65 to 88%), metoprolol (from 45 to 59%), methylparaben (from 64 to 78%) and propylparaben (from 68 to 74%). The heterotrophic co-metabolism of PPCPs driven by glycerol was confirmed by the biodegradation kinetics, in which kbio (biodegradation kinetics constant) values increased from 0.18 to 2.11 to 0.27-3.60 L g-1-VSS d-1, for the operational phases without and with GOH, respectively. The assessment of metabolic pathways in each phase revealed that the prevalence of aromatic compounds degradation, metabolism of xenobiotics by cytochrome P450, and benzoate degradation routes during acidogenesis are key factors for the enzymatic mechanisms linked to the PPCPs co-metabolism. The phase separation of anaerobic digestion was effective in the PPCPs biodegradation, and the co-fermentation of glycerol provided an increase in the generation potential of biomethane in the system (energetic potential of 5.0 and 6.3 kJ g-1-CODremoved, without and with GOH, respectively). This study showed evidence that glycerol co-fermentation can exert a synergistic effect on the PPCPs removal during anaerobic digestion mediated by heterotrophic co-metabolism.

Physiological impact of personal care product constituents on non-target aquatic organisms

Personal care products (PCPs) are products used in cleaning, beautification, grooming, and personal hygiene. The rise in diversity, usage, and availability of PCPs has resulted in their higher accumulation in the environment. Thus, these constitute an emerging category of environmental contaminants due to the potential of its constituents (chemical and non-chemical) to induce various physiological effects even at lower concentrations (ng/L). For analyzing the impact of the PCPs constituents on the non-target organism about 300 article including research articles, review articles and guidelines were studied from 2000 to 2023. This review aims to firstly discuss the fate and accumulation of PCPs in the aquatic environment and organisms; secondly provides overview of environmental risks that are linked to PCPs; thirdly review the trends, current status of regulations and risks associated with PCPs and finally discuss the knowledge gaps and future perspectives for future research. The article discusses important constituents of PCPs such as antimicrobials, cleansing agents and disinfectants, fragrances, insect repellent, moisturizers, plasticizers, preservatives, surfactants, UV filters, and UV stabilizers. Each of them has been found to display certain toxic impact on the aquatic organisms especially the plasticizers and UV filters. These continuously and persistently release biologically active and inactive components which interferes with the physiological system of the non-target organism such as fish, corals, shrimps, bivalves, algae, etc. With a rise in the number of toxicity reports, concerns are being raised over the potential impacts of these contaminant on aquatic organism and humans. The rate of adoption of nanotechnology in PCPs is greater than the evaluation of the safety risk associated with the nano-additives. Hence, this review article presents the current state of knowledge on PCPs in aquatic ecosystems.

Recent Advances in Black Phosphorous-Based Photocatalysts for Degradation of Emerging Contaminants

The recalcitrant nature of emerging contaminants (ECs) in aquatic environments necessitates the development of effective strategies for their remediation, given the considerable impacts they pose on both human health and the delicate balance of the ecosystem. Semiconductor-based photocatalytic technology is recognized for its dual benefits in effectively addressing both ECs and energy-related challenges simultaneously. Among the plethora of photocatalysts, black phosphorus (BP) stands as a promising nonmetallic candidate, offering a host of advantages including its tunable direct band gap, broad-spectrum light absorption capabilities, and exceptional charge mobility. Nevertheless, pristine BP frequently underperforms, primarily due to issues related to its limited ambient stability and the rapid recombination of photogenerated electron-hole pairs. To overcome these challenges, substantial research efforts have been devoted to the creation of BP-based photocatalysts in recent years. However, there is a noticeable absence of reviews regarding the advancement of BP-based materials for the degradation of ECs in aqueous solutions. Therefore, to fill this gap, a comprehensive review is undertaken. In this review, we first present an in-depth examination of the fabrication processes for bulk BP and BP nanosheets (BPNS). The review conducts a thorough analysis and comparison of the merits and limitations inherent in each method, thereby delineating the most auspicious avenues for future research. Then, in line with the pathways followed by photogenerated electron-hole pairs at the interface, BP-based photocatalysts are systematically categorized into heterojunctions (Type I, Type II, Z-scheme, and S-scheme) and hybrids, and their photocatalytic performances against various ECs and the corresponding degradation mechanisms are comprehensively summarized. Finally, this review presents personal insights into the prospective avenues for advancing the field of BP-based photocatalysts for ECs remediation.

Transcriptome analysis reveals differences in developmental neurotoxicity mechanism of methyl-, ethyl-, and propyl- parabens in zebrafish embryos

Studies on the comparison of developmental (neuro) toxicity of parabens are currently limited, and unharmonized concentrations between phenotypic observations and transcriptome analysis hamper the understanding of their differential molecular mechanisms. Thus, developmental toxicity testing was conducted herein using the commonly used methyl- (MtP), ethyl- (EtP), and propyl-parabens (PrP) in zebrafish embryos. With a benchmark dose of 5%, embryonic-mortality-based point-of-departure (M-POD) values of the three parabens were determined, and changes in locomotor behavior were evaluated at concentrations of 0, M-POD/50, M-POD/10, and M-POD, where transcriptome analysis was conducted to explore the underlying neurotoxicity mechanism. Higher long-chained parabens were more toxic than short-chained parabens, as determined by the M-POD values of 154.1, 72.6, and 24.2 µM for MtP, EtP, and PrP, respectively. Meanwhile, exposure to EtP resulted in hyperactivity, whereas no behavioral effect was observed with MtP and PrP. Transcriptome analysis revealed that abnormal behaviors in the EtP-exposed group were associated with distinctly enriched pathways in signaling, transport, calcium ion binding, and metal binding. In contrast, exposure to MtP and PrP mainly disrupted membranes and transmembranes, which are closely linked to abnormal embryonic development rather than neurobehavioral changes. According to the changes in the expressions of signature mRNAs, tentative transcriptome-based POD values for each paraben were determined as MtP (2.68 µM), EtP (3.85 µM), and PrP (1.4 µM). This suggests that different molecular perturbations initiated at similar concentrations determined the extent and toxicity outcome differently. Our findings provide insight into better understanding the differential developmental neurotoxicity mechanisms of parabens.

Ipso Substitution of Aromatic Bromine in Chlorinated Waters: Impacts on Trihalomethane Formation

Parabens and salicylates were examined as disinfection byproduct (DBP) precursors to explore the possible influence of ipso substitution (i.e., halogen exchange) on the yield and speciation of trihalomethanes (THMs) formed during water chlorination. Substoichiometric conversion of C-Br bonds into C-Cl bonds was confirmed for several parabens and salicylates. The co-occurrence of (mono)brominated and nonhalogenated precursors in the presence of free chlorine (but in the absence of added Br-) generated polybrominated THMs, implicating ipso substitution. The THM molar yield, bromine incorporation, and bromine recovery from brominated and nonhalogenated precursor mixtures were commensurate with those observed from equimolar additions of NaBr, indicating efficient displacement of aromatic bromine by free chlorine followed by reincorporation of liberated HOBr into DBP precursors. The THM molar yield from brominated precursors was enhanced by a factor of ≤20 relative to that from nonhalogenated precursors. Trends in THM molar yields and bromine incorporation differed between brominated parabens and brominated salicylates, suggesting that the influence of ipso substitution on THM formation varies with the structure of the organic precursor. Collectively, these results provide new evidence of the often-overlooked role ipso substitution can play in promoting halogen exchange and bromine enrichment among DBPs in chlorinated waters.

The development and application of a novel hazard scoring tool for assessing impacts of cosmetic ingredients on aquatic ecosystems: A case study of rinse-off cosmetics

The cosmetic industry has been committed to promoting less hazardous products to reduce the environmental impacts of cosmetic ingredients. This requires identifying safer cosmetic ingredients for developing cosmetic formulations that are less harmful to the environment. However, one of the challenges in developing eco-friendly cosmetics relies on integrating all environmental hazard (EH) information of cosmetic ingredients to select the most eco-friendly ones (i.e., ingredients least harmful to the aquatic environment). Thus, we developed a hazard scoring tool (IARA matrix), which integrates data on biodegradation, bioaccumulation, and acute aquatic toxicity, providing a hazard index to classify cosmetic ingredients (raw materials) into categories of EH (low, moderate, high, or very high). The classification of the IARA was based on parameters established by Cradle to Cradle (C2C), the US Environmental Protection Agency (USEPA), and European Regulation 1272/2008, considering the most conservative values of each source. The Leopold matrix was employed as a model for the tool, using a numerical scale from 0 to 6 (lowest to highest EH). According to the IARA, we have successfully demonstrated that ultraviolet (UV) filter ingredients have the highest EH out of 41 cosmetic ingredients commonly used for rinse-off products. In addition to UV filters, triclosan (bactericide) and dimethicone (emollient) presented the second-highest EH for aquatic ecosystems, and humectants presented the lowest hazard index. By applying the IARA in the case study of rinse-off products, we have estimated that the aquatic hazard of cosmetic products can be reduced 46% by identifying less hazardous ingredients and combining them into a cosmetic formulation. In summary, the IARA tool allows the estimation of the EH of cosmetic ingredients, provides safer products, and helps achieve sustainability for cosmetic products. Integr Environ Assess Manag 2023;19:1619-1635. © 2023 SETAC.

Influences of Wastewater Treatment on the Occurrence of Parabens, p-Hydroxybenzoic Acid and Their Chlorinated and Hydroxylated Transformation Products in the Brazos River (Texas, USA)

Parabens are ubiquitous, being found in surface waters around the world. Although little is known about the release of paraben transformation products and fate of transformation products in surface water. This study evaluates both parabens and paraben transformation products in the Brazos River upstream and downstream of a wastewater facility located in Waco, Texas. Concentrations of thirteen compounds were reported in this study, five parent parabens and eight paraben disinfection by-products. Analyte concentrations were spatially evaluated to determine if release of wastewater effluent affects their concentrations in the river. Two Brazos River tributaries were also sampled to determine if they released parabens and related compounds to the Brazos. Sampling occurred weekly for one year with at least 40 samples collected at each site. Analyses were completed for both yearly and seasonal data. Sites downstream of wastewater treatment outfalls had lower concentrations of methyl paraben during the yearly analysis and across multiple seasons in the seasonal analysis with average yearly annual methyl paraben concentrations decreasing from 0.83 ng/L at site 3 to 0.09 ng/L at site 4. Para-hydroxybenzoic acid was the compound present in greatest concentration at most sites across most seasons, with the highest average annual concentration of 10.30 ng/L at site 2. Spatial changes in para-hydroxybenzoic acid varied by season, with seasonal trends only identifiable after normalization by flow. Dichlorinated paraben concentrations increased in the river at sites downstream of wastewater treatment with a yearly average dichlorinated methyl paraben concentration of 0.490 ng/L at site 3 to 1.53 at site 4, just downstream of the major wastewater treatment plant. Concentration increases indicate that wastewater effluent contains sufficiently high dichlorinated paraben concentrations to effect concentrations downstream of effluent discharges. Dichlorinated species also persisted in the environment, with no significant decreases at sites further downstream during any season with an annual average dichlorinated methyl paraben concentration of 1.23 ng/L at site 6. Methyl paraben concentrations decreased at the site furthest downstream to a concentration of 0.081 ng/L, while dichlorinated methyl paraben concentrations remained stable with a concentration of 1.10 ng/L at the site furthest downstream. Due to the dichlorinated species being released in higher concentrations in effluent than parents and being more resistant to degradation, the dichlorinated parabens are more likely to be environmentally relevant than are parent parabens.

The Effects of Preservatives on Antibiotic- and Preservative-Resistant Microbes and Nitrogen/Sulfur Cycle Associated Microbial Communities in Freshwater River Sediments

The intensive use of benzoic acid (BA), 4-hydroxybenzoic acid (HB), and dehydroacetate (DHA) as additives and preservatives in cosmetics and foods causes emerging environmental pollutions. Anthropogenic releases of BA, HB and DHA are primarily emissions into water and soil. However, few studies investigate the effects of BA, HB and DHA on microbial communities in freshwater river sediments. The aim of this study is to reveal the effects of BA, HB and DHA on microbial communities in freshwater river sediments. Tetracycline-, sulfamethoxazole- and preservative-resistant microbes were increased in the river sediments treated with BA, HB and DHA. The relative abundances of methanogen- and xenobiotic-degradation-associated microbial communities were also increased in the BA-, HB- and DHA-treated sediments. The relative abundance of four nitrogen cycle associated microbial groups (anammox, nitrogen fixation, denitrification, and dissimilatory nitrate reduction) were increased after the eighth week in the BA-, HB- and DHA-treated sediments. For the sulfur cycle, the relative abundance of thiosulfate oxidation associated microbial communities were increased after the eighth week in the BA-, HB- and DHA-treated sediments. Results of this study provide insight into the effects of BA, HB and DHA on antibiotic resistance, nitrogen cycle, sulfur cycle, drug resistance and methane production in freshwater aquatic environments.

Evaluating seasonal differences in paraben transformation at two different wastewater treatment plants in Texas and comparing parent compound transformation to byproduct formation

Parabens are commonly used preservatives that are weakly estrogenic. Wastewater effluent is the greatest contributor to the spread of parabens into rivers and other surface water. While previous studies indicate parabens are well removed in wastewater treatment by way of transformation, not much is known about the paraben transformation products. This study evaluates paraben transformation and release at two different wastewater treatment plants in Texas. Paraben concentrations were quantified for influent and effluent by season and by year at both treatment plants. Both seasonal and annual transformation rates were compared between the two wastewater treatment plants. Compounds were compared to evaluate differences in transformation rates and to determine if decreases in parent product concentrations are correlated to changes in transformation product concentrations. The study took place over one year and evaluated each season. Spring had higher influent concentrations and transformation rates at treatment plant 1, while summer had higher influent concentrations and transformation rates at treatment plant 2. PHBA was present in greatest amounts in influent and effluent at both sites with average yearly influent concentrations at 223.9 pM at plant 1 and 211.4 pM at plant 2. Transformation rates of parent parabens were greater at plant 1 with concentration of all three shorter chained parabens decreasing by over 50% after treatment. Formation of dichlorinated transformation products were greater at plant 1 with concentrations of Cl₂MeP increasing by 1200% after treatment and Cl₂EtP increasing by 940%. While shorter chained parabens generally had a greater transformation rate, no correlations were found between decreases in methyl and ethyl parabens and the formation of their respective dichlorinated transformation products.

Impact of parabens on drinking water bacteria and their biofilms: The role of exposure time and substrate materials

Parabens have been detected in drinking water (DW) worldwide, however, their impact on DW microbial communities remains to be explored. Microorganisms can easily adapt to environmental changes. Therefore, their exposure to contaminants of emerging concern, particularly parabens, in DW distribution systems (DWDS) may affect the microbiological quality and safety of the DW reaching the consumers tap. This work provides a pioneer evaluation of the effects of methylparaben (MP), propylparaben (PP), butylparaben (BP), and their combination (MIX), in bacterial biofilms formed on different surfaces, representative of DWDS materials - high-density polyethylene (HDPE), polypropylene (PPL) and polyvinyl chloride (PVC). Acinetobacter calcoaceticus and Stenotrophomonas maltophilia, isolated from DW, were used to form single and dual-species biofilms on the surface materials selected. The exposure to MP for 7 days caused the most significant effects on biofilms, by increasing their cellular culturability, density, and thickness up to 233%, 150%, and 224%, respectively, in comparison to non-exposed biofilms. Overall, more pronounced alterations were detected for single biofilms than for dual-species biofilms when HDPE and PPL, demonstrating that the surface material used affected the action of parabens on biofilms. Swimming motility and the production of virulence factors (protease and gelatinase) by S. maltophilia were increased up to 141%, 41%, and 73%, respectively, when exposed to MP for 7 days. The overall results highlight the potential of parabens to interfere with DW bacteria in planktonic state and biofilms, and compromise the DW microbiological quality and safety.

Characterization of pregnant women exposure to halogenated parabens and bisphenols through water consumption

Exposure of pregnant women to endocrine disruptor compounds, such as parabens and bisphenol A is of concern for fetal transition. Their halogenated degradation products, mainly coming from water treatment plans, could be problematic as well, depending on their occurrence in drinking water in the first place. Thus, 25 halogenated compounds were synthesised in order to investigate 60 substances (Bisphenols, parabens and their degradation products) in 325 drinking water samples coming from a French cohort study of pregnant women. Analysis was performed by tandem mass spectrometry coupled to gas chromatography (GC-MS/MS) after SPE extraction and derivation of the contaminants. Results indicate that parabens (methylparaben, n-propylparaben, ethylparaben and n-butylparaben), bisphenols S, A and F, and their degradation product, 4-hydroxybenzoic acid, were detected up to several hundred ng/L in drinking water, with detection frequencies between 16% and 88%. Regarding halogenated degradation products, the highest detection frequencies were found for monochlorinated products (about 50% for 2-chlorobisphenol A), which were quantified up to several tens of ng/L. Such analytical approaches with broader spectrum of monitoring (i.e. chemical hazards and their degradation products) constitute in the beginning of a solution to exhaustively answer the questions related to the characterization of the human chemical exposome.

Endocrine disrupting activity in sewage sludge: Screening method, microbial succession and cost-effective strategy for detoxification

Sewage sludge (SS) presents a high agronomic potential due to high concentrations of organic matter and nutrients, encouraging its recycling as a soil conditioner. However, the presence of toxic substances can preclude this use. To enable the safe disposal of this waste in agriculture, SS requires additional detoxification to decrease the environmental risks of this practice. Although some alternatives have been proposed in this sense, little attention is provided to eliminating endocrine-disrupting chemicals (EDCs). To fill this gap, this study aimed to develop effective and low-cost technology to eliminate EDCs from SS. For this, a detoxification process combining microorganisms and biostimulating agents (soil, sugarcane bagasse, and coffee grounds) was performed for 2, 4, and 6 months with aerobic and anaerobic SSs. The (anti-)estrogenic, (anti-)androgenic, retinoic-like, and dioxin-like activities of SSs samples were verified using yeast-based reporter-gene assays to prove the effectiveness of the treatments. A fractionation procedure of samples, dividing the target sample extract into several fractions according to their polarity, was conducted to decrease the matrix complexity and facilitate the identification of EDCs. A decrease in the abundance and microbial diversity of the SS samples was noted along the biostimulation with the predominance of filamentous fungal species over yeasts and gram-positive bacteria and non-fermenting rods over enterobacteria. Among the 9 EDCs quantified by LC-ESI-MS/MS, triclosan and alkylphenols presented the highest concentrations in both SS. Before detoxification, the studied SSs induced significant agonistic activity, especially at the human estrogen receptor α (hERα) and the human aryl hydrocarbon receptor (AhR). The raw anaerobic sludge also activated the androgen (hAR), retinoic acid (RARα), and retinoid X (RXRα) receptors. However, no significant endocrine-disrupting activities were observed after the SS detoxification, showing that the technology applied here efficiently eliminates receptor-mediated toxicity.

Recent advances in application of metal-organic frameworks (MOFs) as adsorbent and catalyst in removal of persistent organic pollutants (POPs)

The presence of persistent organic pollutants (POPs) in the aquatic environment is causing widespread concern due to their bioaccumulation, toxicity, and possible environmental risk. These contaminants are produced daily in large quantities and released into water bodies. Traditional wastewater treatment plants are ineffective at degrading these pollutants. As a result, the development of long-term and effective POP removal techniques is critical. In water, adsorption removal and photocatalytic degradation of POPs have been identified as energy and cost-efficient solutions. Both technologies have received a lot of attention for their efforts to treat the world's wastewater. Photocatalytic removal of POPs is a promising, effective, and long-lasting method, while adsorption removal of persistent POPs represents a simple, practical method, particularly in decentralized systems and isolated areas. It is critical to develop new adsorbents/photocatalysts with the desired structure, tunable chemistry, and maximum adsorption sites for highly efficient removal of POPs. As a class of recently created multifunctional porous materials, Metal-organic frameworks (MOFs) offer tremendous prospects in adsorptive removal and photocatalytic degradation of POPs for water remediation. This review defines POPs and discusses current research on adsorptive and photocatalytic POP removal using emerging MOFs for each type of POPs.

Screening of antimicrobials, fragrances, UV stabilizers, plasticizers and preservatives in sewage treatment plants (STPs) and their risk assessment in India

Community/industrial wastewater is the prime source of anthropogenic chemicals, its treatment is often a daunting task and unaffordable for many countries. Emerging Contaminants (ECs) have been drained into wastewater after continuous use/misuse and Conventional treatments in STPs do not remove them completely. ECs including antimicrobial agents, synthetic musks, Benzotriazole UV stabilizers (BUVSs), plasticizers, and preservatives are frequently reported in environment, and cause health effects to non-target organisms. Monitoring of ECs is important to understand their status in aquatic environment. Hence, it was aimed to monitor ECs (n = 21) from 11 STPs in Tamil Nadu, India. The detection frequency of most of these analytes was >90%. Antimicrobials ranged from 247 to 22,714 ng/L and 11-14,369 ng/L in influents and effluents, respectively. The synthetic musks were in the order of Tonalide > Galaxolide > Musk Ketone. BUVSs ranged from 4 to 1632 ng/L (influents) and < LOD to 29,853 ng/L (effluents). Concentration of phthalates in influents and effluents were < LOD - 11,311 ng/L and < LOD - 17,618 ng/L, respectively. Parabens were found in the order of Prophyl > Methyl > Ethyl > Butyl in influents and Methyl > Prophyl > Butyl > Ethyl in effluents. Mass loads of ECs through STPs were found as antimicrobials > plasticizers > fragrances > BUVSs > Preservatives. This study reveals increasing usage of ECs and inadequate treatment processes at STPs in India. Also helps to adopt suitable treatment processes to remove ECs from wastewater and to reuse the wastewater.

Monitoring and eco-toxicity effect of paraben-based pollutants in sediments/seawater, north of the Persian Gulf

The current work is documented as the first record of the characteristics, removal efficiency, partitioning behavior, fate, and eco-toxicological effects of paraben congeners in a municipal wastewater treatment plant (WWTP, stabilization ponds) and hospital WWTPs (septic tank and activated sludge), as well as seawater-sediments collected from runoff estuarine stations (RES) and coastal stations (CS) of the north of the Persian Gulf. The median values of Σparabens at the raw wastewater and effluent of the studied WWTPs were 1884 ng/L and 468 ng/L, respectively. The activated sludge system had a greater removal efficiency (56.10%) in removing ∑parabens than the septic tank (45.05%) and stabilization pond (35.54%). The discharge rates of methyl paraben (MeP) was computed to be 2.23, 21.18, and 9.12 g/d/1000 people for stabilization ponds, septic tank, and activated sludge, respectively. Median concentrations of Σparabens in seawater (103.42 ng/L) and sediments (322.05 ng/g dw) from RES stations were significantly larger than from CS stations (61.2 and 262.0 ng/g dw in seawater and sediments, respectively) (P < 0.05). The median of field-based k_oc for Σparabens was 130.81 cm³/g in RES stations and 189.51 cm³/g in CS stations. It was observed that the concentration of parabens could have negative impacts on some living aquatic populations (invertebrates and bacteria), but the risk was not significant for fishes and algae.

Effect of Iron Complex Source on MWWTP Effluent Treatment by Solar Photo-Fenton: Micropollutant Degradation, Toxicity Removal and Operating Costs

Benzophenone-3, fipronil and propylparaben are micropollutants that are potential threats to ecosystems and have been detected in aquatic environments. However, studies involving the investigation of new technologies aiming at their elimination from these matrices, such as advanced oxidation processes, remain scarce. In this study, different iron complexes (FeCit, FeEDTA, FeEDDS and FeNTA) were evaluated for the degradation of a mixture of these micropollutants (100 µg L−1 each) spiked in municipal wastewater treatment plant (MWWTP) effluent at pH 6.9 by solar photo-Fenton. Operational parameters (iron and H2O2 concentration and Fe/L molar ratio) were optimized for each complex. Degradation efficiencies improved significantly by increasing the concentration of iron complexes (1:1 Fe/L) from 12.5 to 100 µmol L−1 for FeEDDS, FeEDTA and FeNTA. The maximum degradation reached with FeCit for all iron concentrations was limited to 30%. Different Fe/L molar ratios were required to maximize the degradation efficiency for each ligand: 1:1 for FeNTA and FeEDTA, 1:3 for FeEDDS and 1:5 for FeCit. Considering the best Fe/L molar ratios, higher degradation rates were reached using 5.9 mmol L−1 H2O2 for FeNTA and FeEDTA compared to 1.5 and 2.9 mmol L−1 H2O2 for FeEDDS and FeCit, respectively. Acute toxicity to Canton S. strain D. melanogaster flies reduced significantly after treatment for all iron complexes, indicating the formation of low-toxicity by-products. FeNTA was considered the best iron complex source in terms of the kinetic constant (0.10 > 0.063 > 0.051 > 0.036 min−1 for FeCit, FeNTA, FeEDTA and FeEDDS, respectively), organic carbon input and cost-benefit (USD 327 m−3 > USD 20 m−3 > USD 16 m−3 > USD 13 m−3 for FeEDDS, FeCit, FeEDTA and FeNTA, respectively) when compared to the other tested complexes.

Mass trends of parabens, triclocarban and triclosan in Arizona wastewater collected after the 2017 FDA ban on antimicrobials and during the COVID-19 pandemic

Antimicrobials like parabens, triclosan (TCS), and triclocarban (TCC) are of public health concern worldwide due to their endocrine-disrupting properties and ability to promote antimicrobial drug resistance in human pathogens. The overall use of antimicrobials presumably has increased during the COVID-19 pandemic, whereas TCS and TCC may have experienced reductions in use due to their recent ban from thousands of over-the-counter (OTC) personal care products by the U.S. Food and Drug Administration (FDA). No quantitative data are available on the use of parabens or the impact the FDA ban had on TCC and TCS. Here, we use wastewater samples (n = 1514) from 10 different communities in Arizona to measure the presence of the six different antimicrobial products (TCS, TCC, and four alkylated parabens [methylparaben (MePb), ethylparaben (EtPb), propylparaben (PrPb), butylparaben (BuPb)]) collected before and during the COVID-19 pandemic using a combination of solid-phase extraction, liquid chromatography/tandem mass spectrometry (LC-MS/MS), and isotope dilution for absolute quantitation. The average mass loadings of all antimicrobials combined (1,431 ± 22 mg/day per 1,000 people) after the onset of the local epidemic (March 2020 - October 2020) were significantly higher (945 ± 62 mg/day per 1,000 people; p < 0.05) than before the pandemic (January 2019 - February 2020). Overall, parabens (∑Pbs = 999 ± 16 mg/day per 1,000 people) were the most used antimicrobials, followed by TCS (117 ± 14 mg/day per 1,000 people) and TCC (117 ± 14 mg/day per 1,000 people). After the 2017 U.S. FDA ban, we found a statistically significant (p < 0.05) reduction in the mass loadings of TCS (-89%) and TCC (-80%) but a rise in paraben use (+72%). Mass flows of 3 of a total of 4 parabens (MePb, EtPb, and PrPb) in wastewater were significantly higher upon the onset of the epidemic locally (p < 0.05). This is the first longitudinal study investigating the use of antimicrobials during the COVID-19 pandemic by employing wastewater-based epidemiology. Whereas an overall increase in the use of antimicrobials was evident from analyzing Arizona wastewater, a notable reduction in the use of TCS and TCC was evident during the pandemic, triggered by the U.S. FDA ban.

Influence of the hydraulic retention time on the removal of emerging contaminants in an anoxic-aerobic algal-bacterial photobioreactor coupled with anaerobic digestion

This work evaluated, for the first time, the performance of an integral microalgae-based domestic wastewater treatment system composed of an anoxic reactor and an aerobic photobioreactor, coupled with an anaerobic digester for converting the produced algal-bacterial biomass into biogas, with regards to the removal of 16 contaminants of emerging concern (CECs): penicillin G, tetracycline, enrofloxacin, ciprofloxacin, sulfamethoxazole, tylosin, trimethoprim, dexamethasone, ibuprofen, naproxen, acetaminophen, diclofenac, progesterone, carbamazepine, triclosan and propylparaben. The influence of the hydraulic retention time (HRT) in the anoxic-aerobic bioreactors (4 and 2.5 days) and in the anaerobic digester (30 and 10 days) on the fate of these CECs was investigated. The most biodegradable contaminants (removal efficiency >80% regardless of HRT) were tetracycline, ciprofloxacin, sulfamethoxazole, tylosin, trimethoprim, dexamethasone, ibuprofen, naproxen, acetaminophen and propylparaben (degraded predominantly in the anoxic-aerobic bioreactors), and tetracycline, sulfamethoxazole, tylosin, trimethoprim and naproxen (degraded predominantly in the anaerobic reactor). The anoxic-aerobic bioreactors provided removal of at least 48% for all CECs tested. The most recalcitrant contaminants in the anaerobic reactor, which were not removed at any of the HRT tested, were enrofloxacin, ciprofloxacin, progesterone and propylparaben.

Enhanced photocatalytic treatment using plasmonic Ag@Ag3PO4/Ag@AgCl nanophotocatalyst for simultaneous degradation of multiple parabens and UV-filters in various aquatic environments under visible light irradiation

In this study, simultaneous photocatalytic degradation of different parabens (methyl-, ethyl-, propyl-, and butyl paraben) and UV filters (benzophenone-3, 4-methylbenzylidene camphor, 2-ethylhexyl 4-(dimethylamino) benzoate, ethylhexyl methoxycinnamate and octocrylene) in water matrices was performed under visible light irradiation using novel double plasmonic Ag^@Ag₃PO₄/Ag^@AgCl nanophotocatalyst, synthesized by an easy and fast photochemical conversion and photo-reduction. It was found that the nanophotocatalyst with appropriate mole ratio of Ag^@Ag₃PO₄/Ag^@AgCl (1:3) showed superior photocatalytic activity than individual plasmonic nanoparticles. This is because there are two simultaneous surface plasmon resonances (SPR) generated by the metallic Ag nanoparticles, in addition to the hetero-junction structure formed at the interface between Ag^@Ag₃PO₄ and Ag^@AgCl. The structures of the synthesized photocatalysts were characterized, and the principal reactive oxygen species in the photocatalytic process were identified via a trapping experiment, confirming superoxide radicals (^∙O₂^-) as the key reactive species of the photocatalytic system. The process of photodegradation of the target pollutants was monitored using an optimized method that incorporated solid-phase extraction in combination with gas chromatography-mass spectrometry. The simultaneous photodegradation process was modeled and optimized using central composite design. The kinetic study revealed that the degradation process over Ag^@Ag₃PO_{4 (30%)}/Ag^@AgCl _(70%) under visible light followed a pseudo-first-order kinetic model. The simultaneous degradation of target compounds was further investigated in sewage treatment plant effluent as well as tap water. It was found that the matrix constituents can reduce the photodegradation efficiency, especially in the case of highly contaminated samples.

Reaction kinetics and degradation efficiency of halogenated methylparabens during ozonation and UV/H2O2 treatment of drinking water and wastewater effluent

This study investigated the reaction kinetics and degradation efficiency of methylparaben and its halogenated products (Cl-, Br-, Cl,Cl-, Br,Cl-, and Br,Br-methylparabens) during ozonation and UV₂₅₄/H₂O₂ treatment. Second-order rate constants for reactions of the parabens with ozone and ^•OH were [Formula: see text] = 10⁷ - 10⁸ M^-1 s^-1 and [Formula: see text] = (2.3 - 4.3)× 10⁹ M^-1 s^-1 at pH 7. Species-specific [Formula: see text] values of the protonated and deprotonated parabens were closely related to phenol ring substituent effects via quantitative structure-activity relationships with other substituted phenols. The UV photolysis rate of the parabens [k_UV = (2.4 - 7.2)× 10^-4 cm² mJ^-1] depended on the halogenation state of the paraben and solution pH, from which species-specific quantum yields were also determined. In simulated treatments of drinking water and wastewater effluent, the parabens were efficiently eliminated during ozonation, requiring a specific ozone dose of > 0.26 gO₃/gDOC for > 97% degradation. During UV/H₂O₂ treatment with 10 mg L^-1 H₂O₂, the degradation levels were > 90% at a UV fluence of 2000 mJ cm^-2, except for Cl,Cl-methylparaben. Kinetic models based on the obtained reaction kinetic parameters could successfully predict the degradation levels of the parabens. Overall, ozonation and UV/H₂O₂ were effective in controlling parabens and their halogenated products during advanced water treatment.

Identifying potential paraben transformation products and evaluating changes in toxicity as a result of transformation

Parabens are a class of compounds often used as preservatives in personal care products, pharmaceuticals, and food. They have received attention recently due to findings that demonstrate estrogenic impacts and other adverse effects of parabens. Release into wastewater effluent is considered a major contributor to the spread of parabens into surface water. Current regulations in areas such as Japan, Europe, and Southeast Asia limit the concentrations of parabens that can be used in formulations but do not address concentrations discharged into waterbodies. Recent studies suggest that parent parabens are effectively eliminated by transformation during the wastewater treatment processes. Common tertiary treatments include ultrafiltration, chlorination, UV disinfection and ozonation. Ultrafiltration is used to remove solids before a disinfection step. Of the disinfection steps, ozonation is often the most effective at removing parabens. Not much is known about the toxicities of paraben transformation products. Of the transformation products, chlorinated parabens and PHBA are the most studied. Previous studies have shown that chlorinated parabens have greatly reduced estrogen agonistic activity when compared with the activity of parents. However, more recent studies have found that halogenated parabens actually have estrogen antagonistic activity. Further research involving chlorinated parabens could include other toxic endpoints. No known studies have evaluated adverse effects of oxygenated parabens. Parabens can interact with chlorine residues in the environment and form chlorinated products, this will occur at a faster rate during chlorination. Ozonation will oxidize parabens and UV disinfection can both oxidize and halogenate parabens. All studies determining potential transformation products have been done in laboratory settings or specific conditions. Further research is needed to determine if these transformations occur in situ. PRACTITIONER POINTS: Common chemical processes utilized by wastewater treatment facilities are effective at transforming parabens. Paraben transformation products are released in greater concentration in effluent than parent paraben compounds. Halogenated transformation products have been identified as estrogen receptor antagonists.

Environmental risk assessment of parabens in surface water from a Brazilian river: the case of Mogi Guaçu Basin, São Paulo State, under precipitation anomalies

Parabens are preservatives widely used by industry since these compounds have antifungal properties, relative low cost, and stability over a wide pH range. This study aims to quantify and assess the environmental risks of methylparaben (MP), ethylparaben (EP), propylparaben (PP), and butylparaben (BP) in surface water from a Brazilian River, Mogi Guaçu. The State of São Paulo, including the Mogi Guaçu River region, suffered from a period of intense drought and high temperatures, which caused anomalies in river flows and water supply problems. The water samples were collected from 14 locations, along 300 km of river extension, at four different seasons. Samples were previously extracted and pre-concentrated by dispersive liquid-liquid microextraction (DLLME) and later analyzed by ultra-performance liquid chromatography coupled with electrospray ionization in tandem with mass spectrometry (UPLC-ESI-MS/MS) detector. During the sampling period, PP was detected in 89.3% of the water samples, MP in 87.5%, EP in 73.2%, and BP in 48.2%. The sum of parabens' average levels was 42.2 μg L^-1 in Winter, 41.5 μg L^-1 in Summer, 36.6 μg L^-1 in Autumn, and 31.5 μg L^-1 in Spring. These levels can be attributed to the smaller dilution effect caused by the drought period. Also, ecological risk assessment indicated that parabens could take a low, medium, and high risk for target organisms in the measured aquatic environments, especially considering Pimephales promelas where 15% of the samples do not present potential risk, 84% of samples can present medium risk and only 1% have low risk. Besides, the risks for BP are also considerably higher, when almost 40% presents for high risks and 60% for medium risks. The present study indicates worrisome threats to the water source and to allegedly protected biodiversity and, therefore, urgent actions are needed to effectively protect.

Phycoremediation integrated approach for the removal of pharmaceuticals and personal care products from wastewater - A review

Pharmaceuticals and personal care products (PPCPs) are of emerging concerns because of their large usage, persistent nature which promised their continuous disposal into the environment, as these pollutants are stable enough to pass through wastewater treatment plants causing hazardous effects on all the organisms through bioaccumulation, biomagnification, and bioconcentration. The available technologies are not capable of eliminating all the PPCPs along with their degraded products but phycoremediation has the advantage over these technologies by biodegrading the pollutants without developing resistant genes. Even though phycoremediation has many advantages, industries have found difficulty in adapting this technology as a single-stage treatment process. To overcome these drawbacks recent research studies have focused on developing technology that integrated phycoremediation with the commonly employed treatment processes that are in operation for treating the PPCPs effectively. This review paper focuses on such research approaches that focused on integrating phycoremediation with other technologies such as activated sludge process (ASP), advanced oxidation process (AOP), Up-flow anaerobic sludge blanket reactor (UASBR), UV irradiation, and constructed wetland (CW) with the advantages and limitations of each integration processes. Furthermore, augmenting phycoremediation by co-metabolic mechanism with the addition of sodium chloride, sodium acetate, and glucose for the removal of PPCPs has been highlighted in this review paper.

Electrochemical degradation of a methyl paraben and propylene glycol mixture: Interference effect of competitive oxidation and pH stability

Endocrine disrupting compounds (EDCs) are one of the many classes of harmful pollutants frequently found in water resources. Even at low concentrations, EDCs might accumulate in the organisms and interfere on numerous processes controlled by hormones. Parabens, for example, are preservatives widely used in pharmaceutical and cosmetic industries, but several studies related them to human breast cancer. It is well-known that electrochemical technologies are an efficient alternative for wastewater treatment, promoting the appropriate destruction of EDCs. However, most studies are applied to single target contaminant solutions, which may neglect the impact from co-exited inorganic/organic pollutants. Based on that, this study aimed to elucidate the interfering effects of two target organic contaminants of very different nature during electrochemical mediated process. For that, methyl paraben (MeP) and propylene glycol (PG) were selected as models of aromatic/phenolic and carboxylate compounds versus low-molecular aliphatic alcohols. These two compounds are often together used in preservative blends and cosmetic/pharmaceutical formulations. PG is not a harmful chemical, but it is present in several types of effluents in relatively high concentrations. Thus, it may interfere on the degradation of numerous pollutants of low concentrations. The electrochemical treatment of a mixture containing 100 mg L^-1 MeP +1000 mg L^-1 PG showed that both contaminants suffered interfering effects. The presence of MeP negatively interfered on PG degradation; the carboxylate compound is more easily oxidized even at lower molecular concentration. On the other hand, the presence of PG showed an unexpected positive effect on MeP degradation, that was not reflected on its mineralization. The results indicate that in addition to the expected effect of anodic competition, polymerization and copolymerization reactions may also occur in the studied system. The use of an acidic buffer medium increased the removal of both contaminants and favored the oxidation pathway over the polymerization. In this case, the increase in the removal was reflected in the mineralization process, which increased up to 6 times when the mixture was treated in the buffered medium.

Toxicity and removal of parabens from water: A critical review

Parabens are biocides used as preservatives in food, cosmetics and pharmaceuticals. They possess antibacterial and antifungal activity due to their ability to disrupt cell membrane and intracellular proteins, and cause changes in enzymatic activity of microbial cells. Water, one of our most valuable natural resource, has become a huge reservoir for parabens. Halogenated parabens from chlorination/ozonation of water contaminated with parabens have shown to be even more persistent in water than other types of parabens. Unfortunately, there is dearth of data on their (halogenated parabens) presence and fate in groundwater which serves as a major source of drinking water for a huge population in developing countries. An attempt to neglect the presence of parabens in water will expose man to it through ingestion of contaminated food and water. Although there are reviews on the occurrence, fate and behaviour of parabens in the environment, they largely omit toxicity and removal aspects. This review therefore, presents recent reports on the acute and chronic toxicity of parabens, their estrogenic agonistic and antagonistic activity and also their relationship with antimicrobial resistance. This article further X-rays several techniques that have been employed for the removal of parabens in water and their drawbacks including adsorption, biodegradation, membrane technology and advanced oxidation processes (AOPs). The heterogeneous photocatalytic process (one of the AOPs) appears to be more favoured for removal of parabens due to its ability to mineralize parabens in water. However, more work is needed to improve this ability of heterogeneous photocatalysts. Perspectives that will be relevant for future scientific studies and which will drive policy shift towards the presence of parabens in our drinking waters are also offered. It is hoped that this review will elicit some spontaneous actions from water professionals, scientists and policy makers alike that will provide more data, effective technologies, and adaptive policies that will address the growing threat of the presence of parabens in our environment with respect to human health.

Fate processes of Parabens, Triclocarban and Triclosan during wastewater treatment: assessment via field measurements and model simulations

The high levels of parabens (including methyl-, ethyl- and propyl congeners), triclocarban (TCC) and triclosan (TCS) used every year in China might be a problem to the typical wastewater treatment plant (WWTP). This study addresses measurements of parabens, TCC and TCS Northern China WWTP and a modelling assessment on the occurrence, fate and removal pathways in WWTP. Per-capita emissions of the three parabens, TCC and TCS to the WWTP were estimated as 0.41, 0.11 and 0.07 mg/d. After the wastewater treatment processes, 94, 92 and 87% of parabens, TCC and TCS were removed. The major removal pathway of parabens was biodegradation while that of TCC and TCS were sorption to sludge. Computer simulations on the fate processes of parabens, TCC and TCS in the WWTP using the SimpleTreat 4.0 model suggested the model could generally reproduce the measurements with root mean squared errors (RMSEs) of less than 10 ng/L. However, the model underestimated the removal of TCC and TCS from water to sludge in the primary tank. These discrepancies were attributed to the uncertainty of the predicted organic carbon-water partition coefficients (K_oc) to which the modelling results are highly sensitive. The model predictions using updated K_oc became more accurate and RMSEs of TCC and TCS were reduced by 40 and 80%, respectively. The modelling assessment suggests that the SimpleTreat, as a generic model to simulate chemical fate processes in WWTPs, has the potential to be applied to other similar WWTPs in China for estimating environmental releases of parabens, TCC and TCS at a larger spatial scale.

Parabens as chemicals of emerging concern in the environment and humans: A review

Parabens are one of the most widely used preservatives in food, pharmaceuticals and personal care products (PCPs) because of their advantageous properties and low toxicity based on the early assessments. However, recent research indicates that parabens may act as endocrine-disrupting chemicals (EDCs) and thus, are considered as chemicals of emerging concern that have adverse human health effects. To provide the basis for future human health studies, we reviewed relevant literature, published between 2005 and 2020, regarding the levels of parabens in the consumer products (pharmaceuticals, PCPs and food), environmental matrices and humans, including susceptible populations, such as pregnant women and children. The analysis showed that paraben detection rates in consumer products, environmental compartments and human populations are high, while the levels vary greatly by country and paraben type. The concentrations of parabens reported in pregnant women (~20-120 μg/L) were an order of magnitude higher than in the general population. Paraben concentrations in food and pharmaceuticals were at the ng/g level, while the levels in PCPs reached mg/g levels. Environmental concentrations ranged from ng/L-μg/L in surface waters to tens of μg/g in wastewater and indoor dust. The levels of human exposure to parabens appear to be higher in the U.S. and EU countries than in China and India, which may change with the increasing production of parabens in the latter countries. The review provides context for future studies to connect paraben exposure levels with human health effects.

Removal efficiency of emerging micropollutants in biofilter wastewater treatment plants in tropical areas

We studied the removal of 61 emerging micropollutants, including illicit drugs, in a biofilter wastewater treatment plant located in the French Indies (Martinique). Raw wastewater concentrations were the highest for paracetamol followed by caffeine, naproxen, ibuprofen, its metabolite 2-hydroxyibuprofen, atenolol, ketoprofen, furosemide, methylparaben, cocaine, benzoylecgonine, and 11-nor-delta-9-carboxytetrahydrocannabinol (THC-COOH). The calculated removals were better than those reported in the literature, while the cumulative removal efficacy (i.e., removal of the total mass load) was estimated to be 92 ± 4%. However, this good performance may be partly explained by the removal of paracetamol (also named acetaminophen) and caffeine, which represented 86.4% of the total mass load. Our results point to the adsorption of some molecules on sludge, thus raising the question about local soil pollution from sludge spreading.

Assessment of the endocrine-disrupting potential of halogenated parabens: An in silico approach

Parabens are endocrine-disrupting chemicals present in a variety of pharmaceutical and personal care products. Due to their wide-spread use, significant amounts are also released into the aquatic domain of the environment. During water disinfection, parabens give rise to halogenated transformation products. As opposed to parabens, there is considerable lack of knowledge with regard to the endocrine-disrupting potential of their halogenated counterparts, which presents a challenge for regulatory decision making. We aimed to fill this knowledge gap by using the Endocrine Disruptome and VirtualToxLab™ to predict their endocrine-disrupting potential on the basis of calculated affinities for different nuclear receptors. The applied computational approach indicates a high probability of halogenated parabens binding to glucocorticoid, thyroid and aryl hydrocarbon receptors and suggests that disinfection is likely to form transformation products with more pronounced endocrine-disrupting activities than those of parent parabens. The obtained results not only highlight the need for additional in vitro/in vivo investigations of these chemicals as endocrine disruptors but also provide a means of guiding and prioritizing these future studies, in order to assess fully their hazard to human health.

Parabens in aerobic granular sludge systems: Impacts on granulation and insights into removal mechanisms

This work assessed the impact of methylparaben, ethylparaben, propylparaben, and butylparaben (200 μg L^-1 each) on the granulation process as well as on the organic matter and nutrient removal of an aerobic granular sludge (AGS) system (6-h cycle). Additionally, some insights into the main paraben removal mechanisms were provided. In the presence of parabens, aerobic granules with good settleability, but with fragile and irregular structure, were grown. No significant effect of parabens on organic matter (>90%) and nitrogen (~70%) removal was evidenced. On the other hand, phosphorus removal was slightly impaired, although high removal efficiencies (~70%) were reached. High paraben removal efficiencies were achieved (>85%) in the AGS system, with methylparaben being the most recalcitrant compound. Concerning the removal mechanisms, biotransformation was the main mechanism in the removal of all parabens (85.5% for methylparaben and 100% for the others), whereas, apparently, adsorption played a role only in the removal of methylparaben. In addition, this compound was also suggested as a probable intermediate of the degradation of the larger alkyl-chain parabens. Lastly, regarding the microbial community, with the exception of Mycobacterium, the reactors shared the same genera, which may explain their comparable operational performances. Additionally, some genera that developed more in the presence of parabens may be related to their degradation. Therefore, although antimicrobial agents such as parabens compromised the granule structure, AGS system maintained a good operational performance and showed to be very efficient in paraben removal.

Removal, seasonal variation, and environmental impact of parabens in a municipal wastewater treatment facility in Guangzhou, China

The occurrence, seasonal variation, and environmental impact of five widely used parabens, methyl-(MeP), ethyl-(EtP), n-propyl-(n-PrP), n-butyl-(n-BuP), and benzyl-(BzP) parabens, were investigated in a municipal wastewater treatment plant (WWTP) located in Guangzhou, China, for 1 year. The concentrations of ∑₅parabens in the influent and the effluent were 94.2-957 and 0.89-14.7 ng L^-1, respectively. The influent paraben concentrations in autumn were significantly lower than in winter, spring, and summer, and the concentrations were generally higher in spring. The removal efficiencies of ∑₅parabens in the dissolved phase were over 96%, with high efficiencies in MeP, EtP, and n-PrP. Risk assessment indicated that parabens in the effluent were not likely to pose an environmental risk to aquatic ecosystems. The present study indicates that the treatment processes employed in full-scale WWTPs are effective at removing parabens and highlights the possibility of utilizing WWTPs for restoring water quality in riverine and coastal regions heavily impacted by paraben contamination.

Ibuprofen as an emerging organic contaminant in environment, distribution and remediation

Pharmaceutical and personal care products (PPCPs) are the one of sub-class under emerging organic contaminants (EOCs). Ibuprofen is the world's third most consumable drug. This drug enters into our water system through human pharmaceutical use. It attracts the attention of environmentalist on the basis of risk associated, presence and transformation in the environment. The detection and removal are the two key area where we need to focus. The concentration of such compounds in waterbodies detected through conventional and also by the advanced methods. This review we described the available technologies including chemical, physical and biological methods, etc used the for removal of Ibuprofen. The pure culture based method, mixed culture approach and activated sludge culture approach focused and pathway of degradation of ibuprofen was deciphered by using the various methods of structure determination. The various degradation methods used for Ibuprofen are discussed. The advanced methods coupled with physical, chemical, biological, chemical methods like ozonolysis, oxidation and adsorption, nanotechnology based methods, nanocatalysis and use of nonosensors to detect the presence of small amount in waterbodies can enhance the future degradation of this drug. It is necessary to develop the new detection methods to enhance the detection of such pollutants. With the developments in new detection methods based on GC-MS//MS, HPLC, LC/MS and nanotechnology based sensors makes easier detection of these compounds which can detect even very minute amount with great sensitivity and in less time. Also, the isolation and characterization of more potent microbial strains and nano-photocatalysis will significantly increase the future degradation of such harmful compounds from the environment.

Occurrence, fate and environmental risk of anionic surfactants, bisphenol A, perfluorinated compounds and personal care products in sludge stabilization treatments

In this work, twenty-three endocrine disrupting compounds have been monitored in sludge from different stages of four sludge stabilization treatments (anaerobic digestion, aerobic digestion, composting and anaerobic stabilization ponds). Their occurrence and fate in sludge stabilization plants and their potential environmental risk in treated sludge and in treated sludge-amended soils have been evaluated. Monitored compounds were six perfluoroalkyl compounds (PFC), four anionic surfactants (sodium alkylsulfates), a plasticiser (bisphenol A (BPA)), four preservatives (parabens), six UV-filters (benzophenones) and two biocides (triclosan and triclocarban). Only two of the UV-filters were not detected in any of the 141 analysed samples. Anionic surfactants (mean concentrations up to 1673 ng/g dry matter (dm) for the sum of surfactants) were the compounds at the highest concentration levels followed by biocides (up to 512 ng/g dm) and UV-filters (up to 662 ng/g dm). The concentrations of anionic surfactants, preservatives and UV-filters decreased 78, 25 and 80%, respectively, after anaerobic digestion. The concentration of perfluorinated carboxylic acids only decreased after composting (80% reduction) whereas biocides and BPA were not affected by any of the studied treatments. Environmental risks (risk quotients > 1) were obtained for all compounds, except for triclocarban and sodium octadecylsulfate, in treated sludge. In treated sludge-amended soils, risk quotients were lower than 1 for all compounds except for triclosan.

Validation of sampling techniques and SPE-UPLC/MS/MS for home and personal care chemicals in the Songhua Catchment, Northeast China

A method for the simultaneous determination of 18 home and personal care chemicals (HPCCs) in river water and wastewater was developed using solid-phase extraction and ultra-high-performance liquid chromatography with tandem mass spectrometry (SPE and UPLC/MS/MS). A series of tests were designed to find the potential background interference and loss of HPCCs during the sample preservation and pretreatment process. Our results suggested that a considerable amount of some target compounds were lost with increasing days of storage even at 4 °C. Accordingly, the samples were stored acidified and refrigerated, including during transportation, to reduce the losses. Experiments on filtration of water samples suggested that recoveries of many HPCCs were significantly affected by the filtration. It is therefore recommended to avoid filtration of water samples where possible. The internal standard corrected recoveries for the HPCCs ranged from 64.2 to 107.0%, except for benzisothiazolone which did not have an appropriate internal standard, in river water which was considered to be the most difficult matrix. The method detection limits for river water, influent and effluent samples were in the ranges of 0.17 to 42 ng/L, 13 to 5100 ng/L, and 0.50 to 200 ng/L, respectively. The validated method was applied for the determination of HPCCs in sewage water collected from a full-scale wastewater treatment plant (WWTP) in a typical urban city in Northeast China and from river water upstream and downstream of the WWTP. Linear alkylbenzene sulphonate, caffeine, methyl paraben, benzalkonium chloride, triclocarban, and triclosan were the major compounds detected in the river water and wastewater samples. Sampling variability for the WWTP (intra-day and inter-day) and cross-river was also determined with the purpose of designing future monitoring requirements. Small variations in these samples confirmed that composite samples and a single sampling event would be representative for future use.

Four typical personal care products in a municipal wastewater treatment plant in China: Occurrence, removal efficiency, mass loading and emission

The occurrence, removal efficiency, mass loading and environmental emission of four categories (benzotriazoles; parabens; antimicrobials; benzophenones) of personal care products were simultaneously determined along the whole process line through an integrated approach (involving both dissolved and adsorbed phase) at a typical wastewater treatment plant in Hunan Province, Southern China. The results showed the prevalence of 13 and 11 target compounds in wastewater and suspended particulate matter, respectively. Twelve substances were detected in the sludge with the mean concentrations ranging from 0.12 to 591.23 ng/g dry weight. Benzotriazoles were the dominant compounds existing in water and antimicrobials were readily being absorbed onto suspended particulate matter and sludge. The overall removal efficiencies of compounds in the total treatment were -84.06%-98.53%. Mass balance results revealed that 85.17%-98.73% of the parabens and benzophenones were removed by degradation, while antimicrobials were removed by being adsorbed onto sludge. However, benzotriazoles could not be efficiently removed and the mass loss was lower than 61.03%. Although ultraviolet radiation played a limited role in removing most target compounds, it still had an impact on removing antimicrobials, 5,6-dimethyl-1H-benzotriazole and 2-hydroxy-4-methoxybenzophenone. The total mass loading and emission of personal care products were 506.35 mg/d/1000 people and 357.56 mg/d/1000 people, respectively. This work would help understand the removal approaches and real pollution of personal care products in the water environment.

The occurrence and risk assessment of phenolic endocrine-disrupting chemicals in Egypt's drinking and source water

This is the first nationwide survey of bisphenol A (BPA), methylparaben, ethylparaben, propylparaben, butylparaben, and o-phenylphenol, in Egypt's water. Five hundred fifty-five water samples were collected from source water (SW, 109 samples) and drinking water (DW, 446 samples) of twenty-three Egyptian governorates. These chemicals were determined by direct ultra-performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) analysis of a filtered aliquot of samples. The impacts of the measured concentrations on the aquatic organisms and human health were evaluated as well. BPA, methylparaben, propylparaben, and butylparaben were frequently detected in SW and DW, while ethylparaben and o-phenylphenol were not detected whatsoever. The most frequently detected endocrine-disrupting chemical (EDC) was BPA in SW and methylparaben in DW. The recorded highest concentrations of BPA and methylparaben in SW and BPA and methylparaben, propylparaben, and butylparaben in DW were the highest worldwide. Of the investigated twenty-three governorates, the SW and DW of Aswan, Red Sea, Cairo, Sharqia, and Damietta were free of the studied EDCs. Contrarily, BPA, MeP, PrP, and BuP were detected in Sohag's SW and DW. A detection ratio > 70% was recorded in SW of Faiyum, Dakahlia, and Ismailia, and > 90% in DW of Sohag, Port Said, Dakahlia, and Faiyum. The environmental risk assessment results excluded any human health risk even in the worst-case scenario and showed that BPA represents the highest risk to the aquatic organisms.

An Insight into Ingredients of Toxicological Interest in Personal Care Products and A Small–Scale Sampling Survey of the Greek Market: Delineating a Potential Contamination Source for Water Resources

Wastewater is not a waste but a valuable resource that should be reused. Nevertheless, it should be devoid of physical, chemical, and microbiological parameters that can harm the consumer. Along with the multitude of possible pollutants found in wastewater treatment plants (WWTPs), emerging pollutants, such as Personal Care Products (PCPs), have arisen. The present research examines some of the main ingredients commonly found in PCPs, focusing on their toxicological profile on their occurrence in WWTPs influents and effluents worldwide and on their persistence and biodegradability. A small-scale market sampling of PCPs was performed in Athens, Greece, in June 2019, and their individual ingredients were recorded, coded according to their main activity, scanned for the presence of ingredients of important toxicological profile, and finally analyzed for the presence of other candidates of toxicological interest. Results show that some ingredients of concern (i.e., parabens and triclosan) are a decreasing trend. On the other hand, information on the presence of synthetic musks and perfume synthesis is scarce and encumbered by brand protection. Finally, UV filters are numerous, and they are used in various combinations, while other ingredients of toxicological interest are also present. Since the reclaimed water may well be used to cover irrigation needs in Greek areas with water deficiency or to enrich bodies of surface water, it is important to know what PCP ingredients are on the rise in the market, to monitor their presence in WWTPs influents and effluents and to extend research on their environmental fate and behavior.

Occurrence, fate and risk assessment of biocides in wastewater treatment plants and aquatic environments in Thailand

This study investigated the occurrence and fate of 19 biocides in 8 wastewater treatment plants and receiving aquatic environments (both freshwater and estuarine systems) in Thailand. The predominant compound in wastewater and surface water was methylparaben with the maximum concentration of 15.2 μg/L detected in the receiving river, while in sludge and sediment was triclocarban with the maximum concentration of 8.47 μg/g in sludge. Triclosan was the main contaminants in the fish samples with the maximum concentration of 1.20 μg/g. Similar results of biocides were found in the estuarine system in Pattaya city, with the maximum concentration of 185 ng/L in sea water for methylparaben, and 242 ng/g in estuarine sediment for triclocarban. The aqueous removal rates for the biocides ranged from 15% to 95% in average. The back estimated-usage and total estimated emission of Ʃ19 biocides in Thailand was 279 and 202 tons/year, respectively. Preliminary ecological risk assessment showed that clotrimazole and triclosan could pose high risks to aquatic organisms in the receiving aquatic environments.

Biodegradation of methyl and butylparaben by bacterial strains isolated from amended and non-amended agricultural soil. Identification, behavior and enzyme activities of microorganisms

The aim of the present study was to investigate the kinetics of methylparaben (MPB) and butylparaben (BPB) removal, two emerging pollutants with possible endocrine disrupting effects, from agricultural soil with and without amendment with compost from sewage sludge used as biostimulant. Compound removal is explained by a first-order kinetic model with half-life times of 6.5/6.7 days and 11.4/8.2 days, in presence/absence of compost, for MPB and BPB respectively. % R² for the fitted model were higher than 96% in all cases. Additionally, isolation of bacteria capable to grow using MPB or BPB as carbon source was also carry out. Laboratory tests demonstrated the ability of these bacteria to biodegrade MPB and BPB from culture media in more than 95% in some cases. These strains showed high ability to biodegrade the compounds. Ten isolates, most of them related to Gram positive bacteria of the genus Bacillus, were identified by 16S rRNA gene sequencing. The study of the enzymatic activities of the isolates revealed both esterase (C4) and esterase-lipase activities.

Distribution and Chemical Analysis of Pharmaceuticals and Personal Care Products (PPCPs) in the Environmental Systems: A Review

PPCPs are found almost everywhere in the environment especially at an alarming rate and at very low concentration in the aquatic systems. Many methods-including pressurized hot water extraction (PHWE), pressurized liquid extraction (PLE), ultrasound-assisted extraction (UAE), and micro-assisted extraction (MAE)-have been employed for their extraction from both surface waters and biota. Solid-phase extraction (SPE) proved to be the best extraction method for these polar, non-volatile, and thermally unstable compounds in water. However, ultrasonic extraction works better for their isolation from sediment because it is cheap and consumes less solvent, even though SPE is preferred as a clean-up method for sediment samples. PPCPs are in groups of-acidic (e.g., diclofenac, ibuprofen, naproxen), neutral (e.g., caffeine, carbamazepine, fluoxetine), and basic pharmaceuticals, as well as antibiotics and estrogens amongst others. PPCPs which are present in trace levels (ng/L) are more often determined by liquid chromatography-mass spectrometry (LC-MS), gas chromatography-mass spectrometry (GC-MS), and high-performance liquid chromatography-ultraviolent (HPLC-UV). Of these, LC-MS and LC-MS-MS are mostly employed for the analysis of this class of compounds, though not without a draw-back of matrix effect. GC-MS and GC-MS-MS are considered as alternative cost-effective methods that can also give better results after derivatization.

Spatial and temporal trends of melamine and its derivatives in sediment from Lake Shihwa, South Korea

Occurrence, spatial distribution, and temporal trends of melamine and its derivatives (ammeline, ammelide, and cyanuric acid) were investigated in surface sediment and two sediment cores collected from Lake Shihwa, South Korea. ∑Melamine (sum of melamine and its three derivatives) was found in all surface sediment samples at concentrations that ranged from 16.6 to 4390 ng/g dry weight (dw), with an average value of 202 ng/g dw. ∑Melamine concentrations exhibited a clear spatial gradient, in decreasing order, as: creeks (mean: 577 ng/g dw) > inshore locations (41.9 ng/g dw) > offshore locations (24.3 ng/g dw). ∑Melamine concentrations were notably high in sediment collected near wastewater treatment plant (WWTP) outfalls. Melamine was the most prevalent compound in sediment collected from creeks (87%) and WWTP outfall locations (48%), whereas cyanuric acid was the dominant compound in sediment from inshore (51%) and offshore (63%) locations. The historical profiles of ∑Melamine in sediment cores corresponded with coastal development and environmental changes in this region. This is the first study to document the occurrence and temporal distribution of melamine in sediment cores, and this information is useful in understanding the fate of these relatively less-studied chemicals in the environment.