High-efficiency electrochemical degradation of phenol in aqueous solutions using Ni-PPy and Cu-PPy composite materials

Detection and treatment of mono and polycyclic aromatic hydrocarbon pollutants in aqueous environments based on electrochemical technology: recent advances

Mono and polycyclic aromatic hydrocarbons are widely distributed and severely pollute the aqueous environment due to natural and human activities, particularly human activity. It is crucial to identify and address them in order to reduce the dangers and threats they pose to biological processes and ecosystems. In the fields of sensor detection and water treatment, electrochemistry plays a crucial role as a trustworthy and environmentally friendly technology. In order to accomplish trace detection while enhancing detection accuracy and precision, researchers have created and studied sensors using a range of materials based on electrochemical processes, and their results have demonstrated good performance. One cannot overlook the challenges associated with treating aromatic pollutants, including mono and polycyclic. Much work has been done and good progress has been achieved in order to address these challenges. This study discusses the mono and polycyclic aromatic hydrocarbon sensor detection and electrochemical treatment technologies for contaminants in the aqueous environment. Additionally mentioned are the sources, distribution, risks, hazards, and problems in the removal of pollutants. The obstacles to be overcome and the future development plans of the field are then suggested by summarizing and assessing the research findings of the researchers.

A Highly Selective Implantable Electrochemical Fiber Sensor for Real-Time Monitoring of Blood Homovanillic Acid

Homovanillic acid (HVA) is a major dopamine metabolite, and blood HVA is considered as central nervous system (CNS) dopamine biomarker, which reflects the progression of dopamine-associated CNS diseases and the behavioral response to therapeutic drugs. However, facing blood various active substances interference, particularly structurally similar catecholamines and their metabolites, real-time and accurate monitoring of blood HVA remains a challenge. Herein, a highly selective implantable electrochemical fiber sensor based on a molecularly imprinted polymer is reported to accurately monitor HVA in vivo. The sensor exhibits high selectivity, with a response intensity to HVA 12.6 times greater than that of catecholamines and their metabolites, achieving 97.8% accuracy in vivo. The sensor injected into the rat caudal vein tracked the real-time changes of blood HVA, which paralleled the brain dopamine fluctuations and indicated the behavioral response to dopamine increase. This study provides a universal design strategy for improving the selectivity of implantable electrochemical sensors.

Selective electrocatalytic transformation of highly toxic phenols in wastewater to para-benzoquinone at ambient conditions

The selective transformation of organics from wastewater to value-added chemicals is considered an upcycling process beneficial for carbon neutrality. Herein, we present an innovative electrocatalytic oxidation (ECO) system aimed at achieving the selective conversion of phenols in wastewater to para-benzoquinone (p-BQ), a valuable chemical widely utilized in the manufacturing and chemical industries. Notably, 96.4% of phenol abatement and 78.9% of p-BQ yield are synchronously obtained over a preferred carbon cloth-supported ruthenium nanoparticles (Ru/C) anode. Such unprecedented results stem from the weak Ru-O bond between the Ru active sites and generated p-BQ, which facilitates the desorption of p-BQ from the anode surface. This property not only prevents the excessive oxidation of the generated p-BQ but also reinstates the Ru active sites essential for the rapid ECO of phenol. Furthermore, this ECO system operates at ambient conditions and obviates the need for potent chemical oxidants, establishing a sustainable avenue for p-BQ production. Importantly, the system efficacy can be adaptable in actual phenol-containing coking wastewater, highlighting its potential practical application prospect. As a proof of concept, we construct an electrified Ru/C membrane for ECO of phenol, attaining phenol removal of 95.8% coupled with p-BQ selectivity of 73.1%, which demonstrates the feasibility of the ECO system in a scalable flow-through operation mode. This work provides a promising ECO strategy for realizing both phenols removal and valuable organics recovery from phenolic wastewater.

Sustainable Electrochemical Activation of Self-Generated Persulfate for the Degradation of Endocrine Disruptors: Kinetics, Performances, and Mechanisms

This study presents an electrolysis system utilizing a novel self-circulation process of sulfate (SO42-) and persulfate (S2O82-) ions based on a boron-doped diamond (BDD) anode and an activated carbon fiber (ACF) cathode, which is designed to enable electrochemical remediation of environmental contaminants with reduced use of chemical reagents and minimized residues. The production of S2O82- and hydrogen peroxide (H2O2) on the BDD anode and ACF cathode, respectively, is identified as the source of active radicals for the contaminant degradation. The initiator, sulfate, is identified by comparing the degradation efficiency in NaSO4 and NaNO3 electrolytes. Quenching experiments and electron paramagnetic resonance (EPR) spectroscopy confirmed that the SO4-· and ·OH generated on the ACF cathode are the main reactive radicals. A comparison of the degradation efficiency and the generated S2O82-/H2O2 of the divided/undivided electrolysis system is used to demonstrate the superiority of the synergistic effect between the BDD anode and ACF cathode. This work provides evidence of the effectiveness of the philosophy of "catalysis in lieu of supplementary chemical agents" and sheds light on the mechanism of the generation and transmission of reactive species in the BDD and ACF electrolysis system, thereby offering new perspectives for the design and optimization of electrolysis systems.

A state-of-art-review on emerging contaminants: Environmental chemistry, health effect, and modern treatment methods

Pollution problems are increasingly becoming e a priority issue from both scientific and technological points of view. The dispersion and frequency of pollutants in the environment are on the rise, leading to the emergence have been increasing, including of a new class of contaminants that not only impact the environment but also pose risks to people's health. Therefore, developing new methods for identifying and quantifying these pollutants classified as emerging contaminants is imperative. These methods enable regulatory actions that effectively minimize their adverse effects to take steps to regulate and reduce their impact. On the other hand, these new contaminants represent a challenge for current technologies to be adapted to control and remove emerging contaminants and involve innovative, eco-friendly, and sustainable remediation technologies. There is a vast amount of information collected in this review on emerging pollutants, comparing the identification and quantification methods, the technologies applied for their control and remediation, and the policies and regulations necessary for their operation and application. In addition, This review will deal with different aspects of emerging contaminants, their origin, nature, detection, and treatment concerning water and wastewater.

Controlling ultrafiltration membrane fouling in surface water treatment via combined pretreatment of O3 and PAC: Mechanism investigation on impacts of technological sequence

In this research, the effects of combined powdered activated carbon (PAC)-ozone (O3) pretreatment on ultrafiltration (UF) performance were comprehensively examined and compared with the conventional O3-PAC pretreatment. The performance of pretreatments on mitigating membrane fouling caused by Songhua River water (SHR) was evaluated by specific flux, membrane fouling resistance distribution, and membrane fouling index. Moreover, the degradation of natural organic matter in SHR was investigated by UV absorbance at 254 nm (UV254), dissolved organic carbon (DOC), and fluorescent organic matter. Results showed that the 100PAC-5O3 process was the most effective in improving the specific flux, with 82.89 % and 58.17 % reductions in the reversible fouling resistance and irreversible fouling resistance respectively. Additionally, the irreversible membrane fouling index was reduced by 20 % relative to 5O3-100PAC. The PAC-O3 process also exhibited superior performance in the degradation of UV254, DOC, three fluorescent components, and three micropollutants in the SHR system compared to O3-PAC pretreatment. The O3 stage played a major role in mitigating membrane fouling, while PAC pretreatment enhanced the oxidation in the subsequent O3 stage during the PAC-O3 process. Furthermore, the Extended Derjaguin-Landau-Verwey-Overbeek theory and pore blocking-cake layer filtration model fitting analysis were employed to explain the mechanisms of membrane fouling mitigation and fouling patterns transformation. It was found that PAC-O3 significantly increased the repulsive interactions between the foulants and the membrane, which restrained the formation of the cake layer filtration stage. Overall, this study evidenced the potential of PAC-O3 pretreatment in surface water treatment applications, providing new insights into the mechanism of controlling membrane fouling and improving the permeate quality.

Hybrid process of adsorption and electrochemically based green regeneration of bentonite clay for ofloxacin and ciprofloxacin removal

Removal of emerging contaminants, such as antibiotics, from wastewater by adsorption is a simple, low-cost, and high-performance process; however, regeneration and reuse of the exhausted adsorbent are necessary to make the process economically viable. This study aimed to investigate the possibility of electrochemical-based regeneration of clay-type materials. For this, the calcined Verde-lodo (CVL) clay was saturated with the antibiotics ofloxacin (OFL) and ciprofloxacin (CIP) in one-component systems by an adsorption process and then subjected to photo-assisted electrochemical oxidation (0.45 A, 0.05 mol/L NaCl, UV-254 nm, and 60 min), which promotes both pollutant degradation and adsorbent regeneration. The external surface of the CVL clay was investigated by X-ray photoelectron spectroscopy before and after the adsorption process. The influence of regeneration time was evaluated for the CVL clay/OFL and CVL clay/CIP systems, and the results demonstrate high regeneration efficiencies after 1 h of photo-assisted electrochemical oxidation. Clay stability during regeneration was investigated by four successive cycles in different aqueous matrices (ultrapure water, synthetic urine, and river water). The results indicated that the CVL clay is relatively stable under the photo-assisted electrochemical regeneration process. Furthermore, CVL clay was able to remove antibiotics even in the presence of natural interfering agents. The hybrid adsorption/oxidation process applied here demonstrated the electrochemical-based regeneration potential of CVL clay for the treatment of emerging contaminants, since it can be operated quickly (1h of treatment) and with lower consumption of energy (3.93 kWh kg^-1) than the traditional method of thermal regeneration (10 kWh kg^-1).

Multifunctional screen-printed films using polymer nanocomposite based on PPy/TiO2: conductive, photocatalytic, self-cleaning and antibacterial functionalities

In this work, two electrically conductive samples based on polypyrrole (PPy) and (PPy/TiO₂) were synthesized via mini-emulsion polymerization. Synthesized samples were used as functional fillers to formulate two different screen-printing pastes (pastes A and B) to obtain the multi-purpose printed films with excellent properties, including electrical conductivity, antibacterial, photocatalytic activity, and self-cleaning. The surface tension, pH, and conductivity measurements validated the acceptable features of the produced pastes. Because of the shear-thinning behavior and viscosity buildup properties of the produced pastes, rheological investigations confirmed their potential for screen-printing. According to I–V test results, the optimum sintering temperature was chosen as a function of electrical conductivity, and the properties of the printed patterns were investigated by varying the printing sequences as 3, 6, and 9 times and sintered at the optimum temperature (90 °C). The contact angle of water on the optimum sample printed by Paste B was ca. 127° and relatively higher than the counterpart printed by Paste A which verified the superiority of the self-cleaning properties of the printed films with latter paste over the former. The photocatalytic studies concerning the degradation of methylene blue showed that the removal percentage of ca. 63% was achieved within the first 90 min of performing the test under UV light. The photocatalytic printed film was addressed the issue of filtering the unused suspension of nanoparticles, which made it difficult to remove the particles from the treated wastewater, in terms of sustainability. The fabricated patterns using Paste B exhibited improved properties, including electrical conductivity, antibacterial and photocatalytic activity.

Phytofabrication of Silver Nanoparticles Using Trigonella foenum-graceum L. Leaf and Evaluation of Its Antimicrobial and Antioxidant Activities

Silver nanoparticles (AgNPs) were fabricated using Trigonella foenum-graceum L. leaf extract, belonging to the variety HM 425, as leaf extracts are a rich source of phytochemicals such as polyphenols, flavonoids, and sugars, which function as reducing, stabilizing, and capping agents in the reduction of silver ions to AgNPs. These phytochemicals were quantitatively determined in leaf extracts, and then, their ability to mediate AgNP biosynthesis was assessed. The optical, structural, and morphological properties of as-synthesized AgNPs were characterized using UV-visible spectroscopy, a particle size analyzer (PSA), FESEM (field emission scanning electron microscopy), HRTEM (high-resolution transmission electron microscopy), and FTIR (Fourier transform infrared spectroscopy). HRTEM analysis demonstrated the formation of spherically shaped AgNPs with a diameter of 4-22 nm. By using the well diffusion method, the antimicrobial potency of AgNPs and leaf extract was evaluated against microbial strains of Staphylococcus aureus, Xanthomonas spp., Macrophomina phaseolina, and Fusarium oxysporum. AgNPs showed significant antioxidant efficacy with IC₅₀ = 426.25 µg/mL in comparison to leaf extract with IC₅₀ = 432.50 µg/mL against 2,2-diphenyl-1-picrylhydrazyl (DPPH). The AgNPs (64.36 mg AAE/g) demonstrated greater total antioxidant capacity using the phosphomolybdneum assay compared to the aqueous leaf extract (55.61 mg AAE/g) at a concentration of 1100 μg/mL. Based on these findings, AgNPs may indeed be useful for biomedical applications and drug delivery systems in the future.

Synthesis of novel PANI/PVA-NiCu composite material for efficient removal of organic dyes

The present work aims the synthesis of a novel, low cost, and environmentally friendly PANI/PVA-CuNi composite by chemical oxidative polymerization of aniline monomer and polyvinyl alcohol (PVA) as film matrix; several percentages of copper (Cu) and Nickel (Ni) were used. UV-Visible spectroscopy, FTIR, SEM-EDX, and TGA were used to characterize the nanocomposites. While PANI/PVA-CuNi nanocomposites were investigated in adsorption experiments of methylene blue (MB) under different controlled conditions (time reaction, adsorbent dosage, initial dye concentration, stirring speed, temperature, and pH of the medium) also various kinetic models were employed to evaluate the efficiency of the adsorption. The results revealed that the10 mg of PANI/PVA-Cu₅₀N_i50 and PANI/PVA-Ni composites Catalyst removed (94% and 93% of methylene blue in 180 min respectively at 10^-5 M initial concentration of dye, pH of 13, stirring speed of 150 rpm, the temperature of 301 k. the kinetics data were properly fitted with the pseudo second-order model with a correlation coefficient of 0.98262 and 0.95881 using PANI/PVA-Cu₅₀N_i50 and PANI/PVA-Ni, respectively.

Polypyrrole-coated copper@graphene core-shell nanoparticles for supercapacitor application

The performance of supercapacitors strongly depends on the electrochemical characterizations of electrode materials. Herein, a composite material consisted of polypyrrole (PPy) and multilayer graphene-wrapped copper nanoparticles (PPy/MLG-Cu NPs) is fabricated on a flexible carbon cloth (CC) substrate via two-step synthesis process for supercapacitor application. Where, MLG-Cu NPs are prepared on CC by one-step chemical vapor deposition synthesis approach; thereafter, the PPy is further deposited on the MLG-Cu NPs/CC via electropolymerization. The related material characterizations of PPy/MLG-Cu NPs are well investigated by scanning electron microscopic, high resolution transmission electron microscopy, Raman spectrometer and x-ray photoelectron spectroscopy; the electrochemical behaviors of the pertinent electrodes are studied by cyclic voltammogram, galvanostatic charge/discharge and electrochemical impedance spectroscopy measurements. The flexible electrode with PPy/MLG-Cu NPs composites exhibits the best specific capacitance of 845.38 F g^-1at 1 A g^-1, which is much higher than those of electrodes with PPy (214.30 F g^-1), MLG-Cu NPs (6.34 F g^-1), multilayer graphene hollow balls (MLGHBs; 52.72 F g^-1), and PPy/MLGHBs (237.84 F g^-1). Finally, a supercapacitor system consisted of four PPy/MLG-Cu NPs/CC electrodes can efficiently power various light-emitting diodes (i.e. red, yellow, green and blue lighs), demonstrating the practical application of PPy/MLG-Cu NPs/CC electrode.

Graphene Nanoplatelet/Multiwalled Carbon Nanotube/Polypyrrole Hybrid Fillers in Polyurethane Nanohybrids with 3D Conductive Networks for EMI Shielding

This work reports the preparation of graphene nanoplatelet (GNP)/multiwalled carbon nanotube (MWCNT)/polypyrrole (PPy) hybrid fillers via in situ chemical oxidative polymerization with the addition of a cationic surfactant, hexadecyltrimethylammonium bromide. These hybrid fillers were incorporated into polyurethane (PU) to prepare GNP/MWCNT/PPy/PU nanohybrids. The electrical conductivity of the nanohybrids was synergistically enhanced by the high conductivity of the hybrid fillers. Furthermore, the electromagnetic interference (EMI) shielding effectiveness (SE) was greatly increased by interfacial polarization between the GNPs, MWCNTs, PPy, and PU. The optimal formulation for the preparation of GNP/MWCNT/PPy three-dimensional (3D) nanostructures was determined by optimization experiments. Using this formulation, we successfully prepared GNP/PPy nanolayers (two-dimensional) that are extensively covered by MWCNT/PPy nanowires (one-dimensional), which interconnect to form GNP/MWCNT/PPy 3D nanostructures. When incorporated into a PU matrix to form a nanohybrid, these 3D nanostructures form a continuous network of conductive GNP-PPy-CNT-PPy-GNP paths. The EMI SE of the nanohybrid is 35-40 dB at 30-1800 MHz, which is sufficient to shield over 99.9% of electromagnetic waves. Therefore, this EMI shielding material has excellent prospects for commercial use. In summary, a nanohybrid with excellent EMI SE performance was prepared using a facile and scalable method and was shown to have great commercial potential.

Carbon-based photocatalysts for hydrogen production: A review

Future energy crises and environmental deterioration may only be avoided by converting solar energy into sustainable, safe, cost-effective, and environmentally friendly technologies such as water splitting. Many researchers and governments throughout the globe have stressed the imperative need for affordable, environmental benign, resistive to corrosion, and earth-abundant nanostructured photocatalysts. This has led scientists to look for a green and cost-effective way to generate energy. As a result, the significance of photo catalyst engineering and reactor design difficulties connected to the performance of the photocatalytic reactions, as well as the examination and analysis of photocatalyst behaviors for adaptable and cost effective H2 production, is emphasized and summarized. The carbon-based materials have an appealing band structure, strong chemical stability, is plentiful on Earth, and is relatively easy to produce, making them suitable for hydrogen production. As example, graphene oxide (GO) with the oxygenated functional groups and graphene and its counterparts, including Graphene quantum dots (GQDs), GO, reduce graphene oxide (rGO), have been demonstrated to be ideal nanocomposite materials due to their superior properties and distribution in matrix and CNTs with excellent electronic transmission efficiency, low cost, stability, and environmental friendly are a great alternative of electron mediators for photocatalytic devices to boost light absorptivity for efficient hydrogen generation but some of them have limited photocatalytic activity due to their low sunlight usage efficiency, therefore the numerous methods, such as doping ions, constructing heterostructure, and functionalizing carbon-based materials, have recently been proven to promote the photocatalytic activity of them. The pore structure of carbon material functions as an acceptor of photogenerated electrons, improved the photocatalyst's specific surface area. Generally low-dimensional carbon materials demonstrated immense promise as highly efficient, low-cost, and environmentally friendly catalysts for hydrogen generation as an energy source. This article reviews the recent research progress on carbon-based materials for hydrogen evolution for the first time. It commences with a quick overview of the present state of affairs and fundamental concepts of hydrogen production in carbon-based nanomaterials for use in this field. We anticipate that this study will inspire readers to expand the use of carbon-based materials in H₂ generation in a more environmentally friendly way.

Synthesis and characterization of g-C3N4-CoFe2O4-ZnO magnetic nanocomposites for enhancing photocatalytic activity with visible light for degradation of penicillin G antibiotic

Nowadays, antibiotic water pollution is an increasingly dangerous environmental threat. Thus, water treatment is essential for their reduction and removal. In recent decades, photocatalysts have attracted much attention due to their influential role in solving this issue. The photocatalytic process, which is one of the green processes and part of advanced oxidation processes, can be a good choice for treating contaminated water containing non-degradable organic matter. However, the design of high-performance photocatalysts under free sunlight can be challenging. In this study, g-C₃N₄-Ca, Mg codoped CoFe₂O₄-ZnO (gCN-CFO-ZnO) nanocomposite photocatalyst was applied in removing penicillin G (PENG) from drug effluents. Also, the effects of contaminant concentration, initial pH, irradiation time, and zinc oxide ratio in the nanocomposites were investigated. The hydrothermal method was carried out to prepare the appropriate composites. Then, the obtained products were characterized by powder X-Ray diffraction (PXRD), Fourier-transform infrared spectroscopy (FT-IR), Raman, field-emission scanning and transmission electron microscope (FE-SEM&TEM), energy dispersive X-Ray (EDX), diffuse reflectance spectroscopy (DRS), vibrating sample magnetometer (VSM) and Photoluminescence (PL) techniques. According to the findings, the degradation of PENG in an acidic environment occurred remarkably; under the same conditions, with decreasing pH from 9 to 5 in the gCN-CFO-ZnO (33.33%) nanocomposite, the degradation efficiency grew from 47% to 74%. Also, the degradation rate of PENG in gCN-CFO-ZnO (16.66%) and gCN-CFO-ZnO (50%) nanocomposites under optimal conditions (pH = 5, PENG the concentration of 10 ppm, and irradiation time of 120 min) was achieved 52% and 60%, respectively. Further, gCN-CFO-ZnO (33.33%) nanocomposite showed higher efficiency in PENG degradation compared to the other two nanocomposites.

Promoting a well-dispersion of MoO3 nanoparticles on fibrous silica catalyst via one-pot synthesis for enhanced photoredox environmental pollutants efficiency

The coexistence of pharmaceutical compounds and heavy metals in the aquatic environment has resulted in complications in the treatment process and thus, causing uproar among the citizens. The radical-based photocatalysis technology has aroused as an excellent method to eliminate both heavy metal and pharmaceutical compounds in the water. Herein, reported the utilization of the microemulsion technique for the preparation of nanoporous fibrous silica-molybdenum oxide (FSMo) towards simultaneous photocatalytic abatement of hexavalent chromium (Cr(VI)) and tetracycline (TC). The FESEM analysis showed the spherical morphology of the FSMo catalyst with dendrimeric silica fiber. The synthesized FSMo catalyst exhibited narrowed bandgap, high crystallinity, and well Mo element dispersion for enhanced photo-redox of Cr(VI) and TC. Remarkably, simultaneous remediation of the Cr(VI) and TC over FSMo demonstrated superior photocatalytic efficiency, 69% and 75%, respectively, than in the individual system, possibly due to the effective separation of photoinduced charges. The introduction of the Mo element to the silica framework via microemulsion technique demonstrated better dispersion of Mo compared to the incipient wetness impregnation method and thus, yielded higher photocatalytic activity towards simultaneous removal of TC and Cr(VI). Besides, quenching experiments revealed the electrons and holes as the active species that play a dominant role in the simultaneous photo-redox of Cr(VI) and TC. Lastly, the FSMo catalyst demonstrated high stability after four continuous cycles of simultaneous photocatalysis reactions, implying its potential as a suitable material for practical wastewater treatments.

Facile synthesis of biogenic palladium nanoparticles using biomass strategy and application as photocatalyst degradation for textile dye pollutants and their in-vitro antimicrobial activity

Among biological applications, plant-mediated Pd NPs for multi-drug resistance (MDR) developed in pathogenic bacteria were synthesized with the help of biomass of lemon peel, a biological material, with a non-toxic, environmentally friendly, human-nature green synthesis method. Characterization of synthesized Pd NPs was carried out by UV-Vis spectrometry, Transmissive Electron Microscopy (TEM), X-ray diffraction (XRD), and Fourier Transform Infrared Spectroscopy (FTIR) techniques. According to TEM analysis, Pd NPs were confirmed to be in a spherical shape and the mean particle size was determined to be 4.11 nm. The crystal structure of Pd NPs was checked using XRD analysis and the mean particle size was observed to be 6.72 nm. Besides, the antibacterial activity of Pd NPs was determined against Escherichia coli (E. coli) (ATCC 8739), Bacillus subtilis (B. subtilis ATCC 6633), Staphylococcus aureus (S. aureus ATCC 6538), Klebsiella pneumoniae (K. pneumoniae ATCC 11296) and Serratia marcescens (S. marcescens ATCC) bacteria. Antibacterial activity was determined to be high in Pd NPs which is in conformance with the results acquired. The Pd NPs showed good photocatalytic activity, after 90 min illumination, about 81.55% and 68.45% of MB and MO respectively were catalysed by the Pd NPs catalyst, and 74.50% of RhB dyes were removed at 120 min of illumination. Within the scope of this project, it is recommended to use Pd NPs obtained by the green synthesis in the future as an antibacterial agent in biomedical use and for the cleaning of polluted waters.

Biosorption of heavy metals by microorganisms: Evaluation of different underlying mechanisms

Globally, ecotoxicologists, environmental biologists, biochemists, pathologists, and other experts are concerned about environmental contamination. Numerous pollutants, such as harmful heavy metals and emerging hazardous chemicals, are pervasive sources of water pollution. Water pollution and sustainable development have several eradication strategies proposed and used. Biosorption is a low-cost, easy-to-use, profitable, and efficient method of removing pollutants from water resources. Microorganisms are effective biosorbents, and their biosorption efficacy varies based on several aspects, such as ambient factors, sorbing materials, and metals to be removed. Microbial culture survival is also important. Biofilm agglomerates play an important function in metal uptake by extracellular polymeric molecules from water resources. This study investigates the occurrence of heavy metals, their removal by biosorption techniques, and the influence of variables such as those indicated above on biosorption performance. Ion exchange, complexation, precipitation, and physical adsorption are all components of biosorption. Between 20 and 35 °C is the optimal temperature range for biosorption efficiency from water resources. Utilizing living microorganisms that interact with the active functional groups found in the water contaminants might increase biosorption efficiency. This article discusses the negative impacts of microorganisms on living things and provides an outline of how they affect the elimination of heavy metals.

Existence of Ti3+ and dislocation on nanoporous CdO-TiO2 heterostructure applicable for degrading chlorophenol pollutant

This study addresses the significance of wastewater recuperation by a simple and facile treatment process known as photocatalyst technology using visible light. Titanium di-oxide (TiO₂) is the most promising photocatalyst ever since longing decades, has good activity under UV light, owing to its small band gap. Hence, TiO₂ has been modified with metal oxides for the positive response against visible light. Since this is an efficient process, the novelty has been made on nanometal oxide CdO (cadmium oxide) combined with TiO₂ to acquire the best efficiency of degrading organic chlorophenol contaminant. Initially, the composites were synthesized by sol-gel and thermal decomposition methods and investigated for their various outstanding properties. The characterized outcomes have exhibited heterostructures with reduced crystallite size from the X-ray diffraction studies. Then, the determination of nanoporous feature was recognized through HR-TEM analysis which was also detected with some dislocations. The EDX spectrum was identified the perfect elemental composition. The nitrogen adsorption-desorption equilibrium was attained that offers many pores measured with high surface area. The XPS result convinced that Ti³⁺ was accessible along with TIO₂/CdO composite. Further the absorption towards higher wavelength was obtained from UV-vis spectra. Finally, for the photocatalytic application of chlorophenol, the composite shows higher percentage of degrading efficiencies than the pristine TiO₂. The photocatalytic mechanism was discussed in detail.

Heavy metal remediation from wastewater using microalgae: Recent advances and future trends

Microalgae-based wastewater treatment has previously been carried out in huge waste stabilization ponds. Microalgae, which can absorb carbon dioxide while reusing nutrients from sewage, has recently emerged as a new trend in the wastewater treatment business. Microalgae farming is thought to be a potential match for the modern world's energy strategy, which emphasizes low-cost and environmentally benign alternatives. Microalgae are being used to treat wastewater and make useful products. Microalgae, for example, is a promising renewable resource for producing biomass from wastewater nutrients because of its quick growth rate, short life span, and high carbon dioxide utilization efficacy. Microalgae-based bioremediation has grown in importance in the treatment of numerous types of wastewater in recent years. This solar-powered wastewater treatment technology has huge potential. However, there are still issues to be resolved in terms of land requirements, as well as the process's ecological feasibility and long-term viability, before these systems can be widely adopted. Due to cost and the need for a faultless downstream process, it is difficult to deploy this technology on a large scale. Other recent breakthroughs in wastewater microalgae farming have been investigated, such as how varied pressures affect microalgae growth and quality, as well as the number of high-value components produced. In this review, the future of this biotechnology has also been examined.

Nano-architectural design of TiO2 for high performance photocatalytic degradation of organic pollutant: A review

In the past several decades, significant efforts have been paid toward photocatalytic degradation of organic pollutants in environmental research. During the past years, titanium dioxide nano-architectures (TiO₂ NAs) have been widely used in water purification applications with photocatalytic degradation processes under Uv/Vis light illumination. Photocatalysis process with nano-architectural design of TiO₂ is viewed as an efficient procedure for directly channeling solar energy into water treatment reactions. The considerable band-gap values and the subsequent short life time of photo-generated charge carriers are showed among the limitations of this approach. One of these effective efforts is the using of oxidation processes with advance semiconductor photocatalyst NAs for degradation the organic pollutants under UV/Vis irradiation. Among them, nano-architectural design of TiO₂ photocatalyst (such as Janus, yolk-shell (Y@S), hollow microspheres (HMSs) and nano-belt) is an effective way to improve oxidation processes for increasing photocatalytic activity in water treatment applications. In the light of the above issues, this study tends to provide a critical overview of the used strategies for preparing TiO₂ photocatalysts with desirable physicochemical properties like enhanced absorption of light, low density, high surface area, photo-stability, and charge-carrier behavior. Among the various nanoarchitectural design of TiO₂, the Y@S and HMSs have created a great appeal given their considerable large surface area, low density, homogeneous catalytic environment, favorable light harvesting properties, and enhanced molecular diffusion kinetics of the particles. In this review was summarized the developments that have been made for nano-architectural design of TiO2 photocatalyst. Additional focus is placed on the realization of interfacial charge and the possibility of achieving charge carriers separation for these NAs as electron migration is the extremely important factor for increasing the photocatalytic activity.

Metal-organic framework-based materials for the abatement of air pollution and decontamination of wastewater

Developing new and efficient technologies for environmental remediation is becoming significant due to the increase in global concerns such as climate change, severe epidemics, and energy crises. Air pollution, primarily due to increased levels of H₂S, SO_x, NH₃, NO_x, CO, volatile organic compounds (VOC), and particulate matter (PM) in the atmosphere, has a significant impact on public health, and exhaust gases harm the natural sulfur, nitrogen, and carbon cycles. Similarly, wastewater discharged to the environment with metal ions, herbicides, pharmaceuticals, personal care products, dyes, and aromatics/organic compounds is a risk for health since it may lead to an outbreak of waterborne pathogens and increase the exposure to endocrine-disrupting agents. Therefore, developing new and efficient air and water quality management systems is critical. Metal-organic frameworks (MOFs) are novel materials for which the main application areas include gas storage and separation, water harvesting from the atmosphere, chemical sensing, power storage, drug delivery, and food preservation. Due to their versatile structural motifs that can be modified during synthesis, MOFs also have a great promise for green applications including air and water pollution remediation. The motivation to use MOFs for environmental applications prompted the modification of their structures via the addition of metal and functional groups, as well as the creation of heterostructures by mixing MOFs with other nanomaterials, to effectively remove hazardous contaminants from wastewater and the atmosphere. In this review, we focus on the state-of-the-art environmental applications of MOFs, particularly for water treatment and air pollution, by highlighting the groundbreaking studies in which MOFs have been used as adsorbents, membranes, and photocatalysts for the abatement of air and water pollution. We finally address the opportunities and challenges for the environmental applications of MOFs.

The synthesis of Pt doped WO3 nanosheets and application on colorimetric detection of cysteine by naked eye using response surface methodology for optimization

We present a simple, sensitive, and specific colorimetric using the peroxidase properties method based on Pt doped WO₃ nanosheets to detect the cysteine. Pt@WO₃NSs were synthesized by hydrothermal method and characterized by Fourier transform infrared (FTIR), Transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDX), and X-ray diffraction patterns (XRD) methods. The response surface methodology (RSM) method based on the central composite design (CCD) was used to optimize test parameters such as pH, nanosheet concentration, and temperature. When cysteine is present in the environment due to its competition with 3,3', 5,5'-Tetramethylbenzidine (TMB) in the use of hydrogen peroxide, the blue discoloration is reduced compared to the absence of cysteine and leads to its detection. We have favorably created a peculiar approach for sensing cysteine based on the colorimetric method in solution and paper with linear range 0.01-15 μM, 0.005-14 μM and R² = 0.9887 and R² = 0.9871 respectively. The detection limit for solution-based is 1.2 nM and for paper-based is 1 nM.

Recent trends and advancements in nanoporous membranes for water purification

When it comes to electrocatalysis, the creation of nanodevices, the research of energy and the environment, and diagnostics, nanoporous materials are an asset. Nanoporous membranes, which can be used to filter water, have recently been the subject of new research and are summarized in this review. These membranes are used to remove salts and metallic ions from the water following an analysis of several nanoporous membrane types and production procedures. Demonstrations and discussions of these membrane systems are then conducted. Nanoporous membranes can be used to filter water, according to the conclusions of this study, which will help readers better grasp how they work. As a result, novel water purification nanoporous compounds that are easy to manufacture, inexpensive, and effective will be developed. Merits and demerits of nanoporous membrane for water treatment and its advancements in purification were discussed.

A modified carbon paste electrode with N-rGO/CuO nanocomposite and ionic liquid for the efficient and cheap voltammetric sensing of hydroquinone in water specimens

This paper reports a voltammetric sensor based on copper oxide nanoparticles on nitrogen-doped reduced graphene oxide nanocomposite (N-rGO/CuO)-ionic liquid modified carbon paste electrode (N-rGO/CuO-ILCPE) for determining the hydroquinone (HQ). The N-rGO/CuO was prepared by a facile protocol, followed by characterization via fourier transform-infrared (FT-IR) patterns, field emission-scanning electron microscopy (FE-SEM), energy dispersive X-ray (EDX), and X-ray diffraction (XRD) analysis. The electrochemical behaviour was linearly symmetrical to various hydroquinone levels (1.0-600.0 μM) with a narrow limit of detection (LOD = 0.25 μM). The diffusion coefficient was also estimated to be 4.1 × 10^-6 cm²/s. The N-rGO/CuO-ILCPE was impressively applicable in determination of hydroquinone in the real specimens.

Electrochemical monitoring of bisphenol-s through nanostructured tin oxide/Nafion/GCE: A solution to environmental pollution

Over the past few decades, phenolic compounds have been broadly exploited in the industries to be utilized in several applications including polycarbonate plastic, food containers, epoxy resins, etc. One of the major compounds in phenolics is Bisphenol-S (BPS) which has dominantly replaced Bisphenol-A in several applications. Phenolic compounds are extensively drained into the environment without proper treatment and cause several health hazards. Thus, to tackle this serious problem an electrochemical sensor based on SnO₂/GCE has been successfully engineered to monitor the low-level concentration of BPS in water samples. The fabrication of SnO₂ nanoparticles (SnO₂ NPs) was confirmed through FTIR, XRD, and TEM to examine the size, crystallinity, internal texture, and functionalities of the prepared material. The fabricated material was exploited as a chemically modified sensor for the determination of BPS in water samples collected from different sources. Under optimal conditions such as scan sweep 100 mV/s, PBS electrolyte pH of 6, potential window (0.3-1.3 V), the proposed sensor manifested an excellent response for BPS. The LOD of the present method for BPS was calculated as 0.007 μM, respectively. Moreover, the stability and selectivity profile of SnO₂/GCE for BPS in the real matrix was examined to be outstanding.

A reusable and sensitive electrochemical sensor for determination of idarubicin in environmental and biological samples based on NiFe2O4 nanospheres anchored N-doped graphene quantum dots composite; an electrochemical and molecular docking investigation

An ultrasensitive and selective voltammetric sensor with ultra-trace level detection limit is introduced for idarubicin (IDA) determination in real samples. The as-synthesized nanocomposite was characterized by several techniques, including Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), Raman spectroscopy, Energy-dispersive X-ray spectroscopy (EDX), and Field emission scanning electron microscopy (FE-SEM). The electrocatalytic performance of the developed electrode was observed by cyclic voltammetry (CV), differential pulse voltammetry (DPV), electrochemical impedance spectroscopy (EIS), and chronoamperometry. The limit of detection (LOD) of the developed sensor for idarubicin is 1.0 nM, and the response is found to be in the dynamic concentration range of 0.01-1.9 μmol/L in a Britton-Robinson buffer (B-R, pH = 6.0). Moreover, the fabricated electrode illustrated high selectivity with good repeatability and reproducibility for diagnosing idarubicin as an anthracycline antileukemic drug. Furthermore, to evaluate the validity of the recommended method, three real samples, including human plasma, urine, and water samples, were analyzed with satisfactory recovery and compared with high-performance liquid chromatography (HPLC). The minor groove-binding mode of interaction was also supported by docking simulation studies, emphasizing that IDA can bind to ds-DNA preferably and confirmed experimental results. The reduced assay time and the possibility of measuring a single sample with another anticancer drug without any interference are significant advantages compared to the HPLC. The developed and validated sensor could be a valuable point-of-care diagnostic tool for IDA quantification in patients.

PbS/graphene hybrid nanostructures coated glassy carbon electrode for the electrochemical sensing of copper ions in aqueous solution

In this research, we have studied the electrochemical sensing of Cu(II) ions in aqueous solution using PbS/Graphene composite nanostructure coated glassy carbon electrode (GCE). The SEM-EDAX analysis revealed that the lead sulphide nanocrystals are homogeneously embedded on the graphene nanosheets with an uniform particle size of 100 nm, and the elements presents 92.32% and Lead content of 5.45% and Sulfur content of 0.91%. Raman spectra exhibits G with respect to the E2g sp² hybridized C-C and D band with respect to the A1g mode in the disordered edge region of the GNS. The composite nanostructure coated GCE (PbS/Graphene/GCE) was prepared and its performance in the existence of metal ions such us Cd(II),Pb(II), Mg(II), Cu(II) and Ni(II) was studied using the current voltage curves in double distilled water within the scan rates of 25 to 300mVs-¹. The PbS/Graphene coated carbon electrode exhibited the higher anodic and cathodic peak current for copper solution than the other metal ions studied, which various linearly proportional to concentration. The electrochemical sensing characteristics PbS/GNS/GCE was found to be significant towards detecting Cu²⁺ ion within the concentration range of 1 × 10^-4 to 1 × 10^-8 M, with a lowest sensing detection limit of 1 × 10^-8 M.

Investigation into Biosorption of Pharmaceuticals from Aqueous Solutions by Biocomposite Material Based on Microbial Biomass and Natural Polymer: Process Variables Optimization and Kinetic Studies

Biosorbtive removal of the antibacterial drug, ethacridine lactate (EL), from aqueous solutions was investigated using as biosorbent Saccharomyces pastorianus residual biomass immobilized in calcium alginate. The aim of this work was to optimize the biosorption process and to evaluate the biosorption capacity in the batch system. Response surface methodology, based on a Box–Behnken design, was used to optimize the EL biosorption parameters. Two response functions (removal efficiency and biosorption capacity) were maximized dependent on three factors: initial concentration of EL solution, contact time, and agitation speed. The highest values for the studied functions (89.49%, 26.04 mg/g) were obtained in the following operational conditions: EL initial concentration: 59.73 mg/L; contact time: 94.26 min; agitation speed: 297.57 rpm. A number of nonlinear kinetic models, including pseudo-first-order, pseudo-second-order, Elovich, and Avrami, were utilized to validate the biosorption kinetic behavior of EL in the optimized conditions. The kinetic data fitted the pseudo-first-order and Avrami models. The experimental results demonstrated that the optimized parameters (especially the agitation speed) significantly affect biosorption and should be considered important in such studies.

Relationship between graphene and pedosphere: A scientometric analysis

The mass production and application of graphene have gradually expanded from academic research to industrial applications, which will inevitably lead to graphene entering the soil actively and passively. Therefore, the relationship between graphene and the pedosphere has attracted a lot of attention in the last decade. The most important question is whether graphene will harm soil health. Fortunately, the evidence is that graphene can alter soil physicochemical properties and microbial communities to some extent, but not dramatically. On this basis, the role of graphene in soil has been investigated in all directions. This review summarizes the literature on the relationship between graphene and soils. Topics include remediation and sensing of soil using graphene materials, the effects of graphene on soil, and the effects of graphene in soil on plant growth. At the same time, this review also uses bibliometrics to review the history of the topic. The number of papers published each year, participating countries, participating institutions and important articles were analyzed in detail. Finally, based on the published literature, we described the future perspectives of graphene and the pedosphere.

Development of paper-based DNA sensor for detection of O. tsutsugamushi using sustainable GQDs@AuNPs nanocomposite

The graphene quantum dots (GQDs) was synthesized using potato starch and water by hydrothermal method and further used for reduction of tetracholoroauric acid to form graphene quantum dots-gold (GQDs@AuNPs) nanocomposite. The GQDs/GQDs@AuNPs were analyzed using FTIR, UV-Vis, Flourometry and HR-TEM. The synthesized GQDs@AuNPs were further used for fabrication of cost-effective screen-printed paper electrode (SPPE) based DNA sensor for the detection of O. tsutsugamushi using htrA gene specific 5'NH2 linked DNA probe. Modification of SPPE using GQDs@AuNPs nanocomposite and ssDNA probe was monitored using EIS, FTIR, FE-SEM and AFM. The sensor detection limit (LOD) was assessed as 0.002 ng/μl from the standard calibration curve with the correlation coefficient, R² = 0.993. The sensitivity of the DNA sensor was calculated as 7700 μA/cm²/ng for ssGDNA of O. tsutsugamushi using cyclic voltammetry. The sensor validation was done using scrub typhus patient's blood DNA samples. The sensor showed good storage stability at 4 °C for six months with just a loss of 12% of the initial current values. The SPPE/DNA sensor developed is very specific, sensitive, stable and detects O. tsutsugamushi in less time.

An improved electrochemical sensor based on triton X-100 functionalized SnO2 nanoparticles for ultrasensitive determination of cadmium

The drastic increases in the concentration of heavy metals ions in the environment have become a serious concern for a number of years. Heavy metals pose serious impacts on human and aquatic life and cause severe health hazards. Amongst heavy metals, cadmium is known for its lethal effects on human health as it easily reacts with enzymes and creates free radicals in the biological system that causes carcinogenicity and other serious diseases. Thus, to tackle this challenge, TX-100 SnO₂ nanoparticles based chemically modified sensor is introduced to assess the quantity of Cd⁺² in the water system. The engineered SnO₂ nanoparticles were electrochemically characterized through cyclic voltammetry and electrochemical impedance spectroscopy to ensure the better charge transfer kinetics and electrocatalytic properties of fabricated sensors. Under the optimized conditions e.g., scan rate 80 mV/s, PBS electrolyte pH 7, and potential window (-0.2 to -1.4 V), the engineered TX-100/SnO₂/GCE-based sensor manifested a phenomenal response for cadmium ions in water media. The LOD and LOQ of developed TX-100/SnO₂/GCE were calculated in the nanomolar range as 0.0084 nM and 0.27 nM. The recovery values of the proposed method for Cd⁺² were found in an acceptable limit that witnesses the effectiveness of the fabricated sensor. Moreover, the excellent stability and anti-interference behavior of the sensor highlights its dynamic profile to be commercially utilized for the determination of Cd⁺² ions in water bodies.

Natural and anthropogenic origin of metallic contamination and health risk assessment: A hydro-geochemical study of Sehwan Sharif, Pakistan

Heavy metal contamination in groundwater is a serious threat to the environment and therefore its proper monitoring is a matter of great concern these days. In the present research, groundwater samples from Sehwan Sharif district Jamshoro, Pakistan were collected to estimate the concentration of various elements including potentially hazardous metals. Statistical analysis of the collected data based on Pearson co-relation metal clustering and Principal Component Analysis (PCA) divides the elements into three groups; Group I contains As, Cu, Ni, and Cd, Group II contains Mn, Fe, B, and Cr and Group III contains Pb and Zn. The elements Cu, Ni, As, Pb, Cd, and Zn found with higher RSD values demonstrate their anthropogenic origin whereas the lower concentration of Mn, Fe, B, and Cr indicate their natural origin (Tepanosyan et al., 2016). The histograms and box-plots of Mn, Fe, B and Cr were found normally distributed while abnormal for Cu, Ni, Pb, As, Cd and Zn. The HQs of these elements indicate their non-carcinogenic risks. However, results of individual metallic behavior indicate the highest HQ measured for B followed by HQs for Cu, and As. The toxic effects of investigated metal (loid)s calculated using HI were found to be 1.58 for adults and 1.35 for the child which is considered the medium chromic risk and cancer risk. About the toxicity of these heavy metals, their cancer risk was assessed on the levels of Cd, As, and Cr in groundwater. The carcinogenic risk of As was found to be 2.78 × 10^-4 and 1.62 × 10^-3 for child and adult, respectively. Furthermore, the values of this carcinogenic risk are 2.64 × 10^-6 and 1.54 × 10^-5 for Cd while 4.24 × 10^-3 and 2.48 × 10^-2 for Cr in child and adult, respectively. Since cancer risk exceeded the target risk of 1 × 10^-4 for As and Cr in adults and children, it can thus be considered 'non-acceptable'. The Geographic Information System (GIS) based maps were prepared using Inverse Distance Weighted (IDW) interpolation which showed the Spatial distribution of all elements throughout Sehwan Sharif from different sources of environment. Spatial maps of elements produced by ArcGIS show the hotspots of potentially hazardous elements such as the highest concentration of Pb, As, Zn, Cu, Ni, and Cd were found in urban areas of Sehwan Sharif district Jamshoro, Pakistan.

Sustainable adsorbents for the removal of pharmaceuticals from wastewater: A review

Over the previous three decades, the worldwide use of pharmaceuticals has surged by more than 2.5 times. Although being considered essential to save many lives, pharmaceuticals have also emerged as a large source of complex environmental contaminants in recent decades. Consequently, the pharmaceuticals and their breakdown products are ending up into the water bodies thus progressively contaminating them and the surrounding environments. Based on recent studies concentrations in water sources are typically >0.1 μg/l and the concentration in treated water is typically >0.05 μg/l. These pharma drugs are removed from aquatic systems by processes such as oxidation, Ultraviolet degradation, reverse osmosis and nano-filtration. However, hazardous sludge creation, incomplete removal, expensive capital and operating costs, and the need for professional operating and maintenance personnel have all limited the economic sustainability of these systems. As a result, the presence of pharmaceuticals in water necessitates even more advanced technologies of purification to harvest clean water, yet present approaches are constrained by their high costs, low reusability, and disposal issues. Here, we review sustainable adsorbents for the removal of pharmaceuticals from wastewater. In this comprehensive review, an evaluation of water contamination caused by pharmaceutical compounds is discussed. An overview of current research on the employment of sustainable adsorbents for the removal of the major pharmaceuticals prevalent in water sources. Numerous aspects of high adsorption efficiencies of these pharmaceutical compounds with such sustainable adsorbents were observed; however, other factors, such as adsorbent regeneration and cost evaluation, must be taken into account in order to assess the true applicability of adsorbents.

Magnetic nanoparticles based on cerium MOF supported on the MWCNT as a fluorescence quenching sensor for determination of 6-mercaptopurine

In this study, a new magnetic nanocomposite was developed as an efficient and fast-response fluorescence quenching sensor for determination of anticancer drug 6-mercaptopurine (6-MP). For this purpose, the needle-shape fluorescence metal-organic framework of cerium (Ce-MOF) were successfully synthesized on the surface of multiwalled carbon nanotubes using 1,3,5-benzenetricarboxylic acid ligand via a facile solvothermal assisted route and magnetized. The accuracy of the proposed synthesis was confirmed using the FT-IR, FE-SEM, XRD, and VSM methods. The obtained product as presented the fluorescence emission in 331 nm by excitation of 293 nm in excitation/emission slit widths of 10.0 nm. The operation of suggested method is based on quenching the fluorescence signal in accordance with increasing the 6-MP concentration. The proposed assay effectively detected the trace amount of 6-MP in the linear range of 1.0 × 10^-6 to 7 × 10^-5 M. The limit of detection and limit of quantification were obtained as 8.6 × 10^-7 and 2.86 × 10^-6 M, respectively. The analyte molecule was determined in real samples with satisfactory recoveries between 98.75 and 105.33.

Synthesis of green benzamide-decorated UiO-66-NH2 for biomedical applications

Metal-organic frameworks (MOFs) biocompatible systems can host enzymes/bacteria/viruses. Herein we synthesized a series of fatty acid amide hydrolase (FAAH)-decorated UiO-66-NH₂ based on Citrus tangerine leaf extract for drug delivery and biosensor applications. Five chemically manipulated FAAH-like benzamides were localized on the UiO-66-NH₂ surface with physical interactions. Comprehensive cellular and molecular analyses were conducted on HEK-293, HeLa, HepG2, PC12, MCF-7, and HT-29 cell lines (cytotoxicity assessment after 24 and 48 h). MTT results proved above 95 and 50% relative cell viability in the absence and presence of the drug, respectively. A complete targeted drug-releasing capability of nanocarriers was demonstrated after capping with leaf extract from Citrus tangerine, with a stimuli-responsive effect in acidic media. Targeted delivery was complete to the nucleus and cytoplasm of HT-29 cell, but merely to the cytoplasm of HeLa cell lines. Nanocarrier could be targeted for drug delivery to the cytoplasm of the HeLa cell line and to both the nucleus and cytoplasm of HT-29 cell lines. MOF-based nanocarriers proved authentic in vivo towards kidney and liver tissues with targeted cancerous cells efficiently. Besides, FAAH-like molecules revealed optical biosensor potential with high selectivity (even ˂5 nM LOD) towards ssDNA, sgRNA, and Anti-cas9 proteins.

Removal of pharmaceuticals (diclofenac and amoxicillin) by maltodextrin/reduced graphene and maltodextrin/reduced graphene/copper oxide nanocomposites

Due to the scarcity of water and the growing industrialization, pharmaceutical wastewater treatment is of particular importance. For this reason, it is necessary to achieve an efficient method to eliminate all types of pharmaceutical pollutants. Herein, synthetic nano-composite is proposed to take a step towards improving the operation of removing pharmaceutical contaminants from the environment and aquatic and industrial effluents. Binary (maltodextrin/reconstituted graphene nanocomposite) and ternary (maltodextrin/reconstituted graphene nanocomposite/copper oxide) nanocomposites were prepared and characterized using, FT-IR, FESEM-EDS, TEM, DLS, and XRD. The nanocomposites were used to eliminate diclofenac and amoxicillin as Pharmaceuticals. The removal of amoxicillin at a concentration of 30 mg/L with an adsorbent dose of 0.05 g and a pH of 7.4 and an optimal temperature of 20 °C in 10 min has the highest removal rate of 86%. In addition, diclofenac with nano-adsorbents prepared under optimal conditions, including an initial concentration of 20 mg/L, adsorbent dose of 0.05 g, adsorption time of 7 min, a temperature of 20 °C and a pH of 7, has the highest removal efficiency of 94%. The results indicated that the prepared nanocomposites are alternative adsorbents to remove Pharmaceuticals from water.

Recent progress on the phytotoxic effects of hydrochars and toxicity reduction approaches

Hydrothermal carbonization of wet biomasses has been known to produce added-value materials for a wide range of applications. From catalyst substrates, to biofuels and soil amendments, hydrochars have distinct advantages to offer compared to conventional materials. With respect to the agricultural application of hydrochars, both positive and negative results have been reported. The presence of N, P and K in certain hydrochars is appealing and may contribute to the reduction of chemical fertilizer application. However, regardless of biomass, hydrothermal carbonization results in the production of phytotoxic organic compounds. Additionally, hydrochars from sewage sludge often contain heavy metal concentrations which exceed the regulatory limits set for agricultural use. This review critically discusses the phytotoxic aspects of hydrochar and provides an account of the substances commonly responsible for these. Furthermore, phytotoxicity reduction approaches are proposed and compared with each other, in view of field-scale applications.

Fabrication of activated carbon supported modified with bimetallic-platin ruthenium nano sorbent for removal of azo dye from aqueous media using enhanced ultrasonic wave

Herein, activated carbon supported modified with bimetallic-platin ruthenium nano sorbent (PtRu@AC) was synthesized by a thermal decomposition process and used in the removal of methylene blue (MB) from aqueous solutions. The synthesized nano sorbents were characterized by X-ray Diffraction (XRD), Transmission Electron Microscopy (TEM), and X-ray Photoelectron Spectroscopy (XPS) spectroscopic techniques. The data obtained from characterization studies showed that PtRu@AC nano sorbent was highly crystalline and in a form of PtRu alloy with a monodispersed composition. The results indicated that the maximum adsorption capacity (qemax) for the removal of MB with PtRu@AC under optimum conditions was detected to be 1.788 mmol/g (569.4 mg/g). The experimental kinetic results of the study revealed that the adsorption of methylene blue was found to be more compatible with the false second-order model compared to some tested models. Calculations for thermodynamic functions including enthalpy change (ΔHo), entropy change (ΔSo), and Gibbs free energy change (ΔGo) values were performed to get an idea about the adsorption mechanism. As a result, the synthesized PtRu@AC nano adsorbent was detected as a highly effective adsorbent material in the removal of MB from aquatic mediums.

Ball milling transformed electroplating sludges with different components to spinels for stable electrocatalytic ammonia production under ambient conditions

Electroplating sludge is classified as hazardous waste, but it is also a potential raw resource since it contains plenty of transition metals. However, the component of electroplating sludge is unstable, which hinders recycling. This work investigates the possibility to synthesize spinels with stable catalytic performances by different electroplating sludges. The obtained catalysts are used in electrocatalytic N₂ reduction to produce ammonia. As a result, CuCr₂O₄, ZnCr₂O₄, and NiCr₂O₄ spinels are successfully synthesized by a ball-milling and calcination method. These spinels result in ammonia yields of 7.30-8.86 μg h^-1 mg^-1_cat. Among the three spinels, CuCr₂O₄ shows the highest yield of 8.86 μg h^-1 mg^-1_cat at -0.9 V. Its faradaic efficiency reaches 0.57%. In addition, no by-product N₂H₄ is detected, indicating a high selectivity. The catalytic process is carried out by both distal and alternating pathways, in which metal doping and oxygen vacancy function as binding sites for N₂ adsorption and reduction. Above results indicate that electroplating sludges with unstable components are feasible to produce spinels for stable electrocatalytic ammonia production under ambient temperature. This is in favor of high-value-added utilization of hazardous waste, and devotes to circular economy.

Development of electrochemical aptasensors detecting phosphate ions on TMB substrate with epoxy-based mesoporous silica nanoparticles

This study, it is aimed to develop an electrochemical aptasensor that can detect phosphate ions using 3.3'5.5' tetramethylbenzidine (TMB). It is based on the principle of converting the binding affinity of the target molecule phosphate ion (PO₄^3-) into an electrochemical signal with specific aptamer sequences for the aptasensor to be developed. The aptamer structure served as a gate for the TMB to be released and was used to trap the TMB molecule in mesoporous silica nanoparticles (MSNPs). The samples for this study were characterized by transmission electron spectroscopy (TEM), Brunner-Emmet-Teller, dynamic light scattering&electrophoretic light scattering, and induction coupled plasma atomic emission spectroscopy. According to TEM analysis, MSNPs have a morphologically hexagonal structure and an average size of 208 nm. In this study, palladium-carbon nanoparticles (Pd/C NPs) with catalytic reaction were used as an alternative to the biologically used horseradish peroxidase (HRP) enzyme for the release of TMB in the presence of phosphate ions. The limit of detection (LOD) was calculated as 0.983 μM, the limit of determination (LOQ) was calculated as 3.276 μM, and the dynamic linear phosphate range was found to be 50-1000 μM. The most important advantage of this bio-based aptasensor assembly is that it does not contain molecules such as a protein that cannot be stored for a long time at room temperature, so its shelf life is very long compared to similar systems developed with antibodies. The proposed sensor shows good recovery in phosphate ion detection and is considered to have great potential among electrochemical sensors.

Preparation of highly sensitive electrochemical sensor for detection of nitrite in drinking water samples

Nitrite is both an environmental contaminant and a food additive. Excessive intake of nitrites not only causes blood diseases, but also has the potential risk of causing cancer. Therefore, rapid detection of nitrite in water is necessary. In this work, we propose an electrochemical sensor for the sensing of nitrite. Glassy carbon electrodes modified with noble metal nanomaterials have been widely used in the preparation of sensors, but the surface properties of noble metals largely affect the sensing performance. This work proposes the biosynthesis of Au nanoparticles using the pollen extract of Lycoris radiata as a reducing agent. Flavonoids rich in pollen can be used as weak reducing agents for the reduction of chloroauric acid, and slowly synthesize uniformly dispersed Au nanoparticles. These Au nanoparticles do not agglomerate because they contain small biological molecules on the surface and can form a homogeneous sensing interface on the electrode surface. The electrochemical sensor assembled with biosynthesized Au nanoparticles provides linear detection of nitrite between 0.01 and 3.8 mM. The sensor also has excellent immunity to interference. In addition, the proposed sensor was also successfully used for the detection of nitrite in drinking water.

Aurivillius Oxides Nanosheets-Based Photocatalysts for Efficient Oxidation of Malachite Green Dye

Aurivillius oxides ferroelectric layered materials are formed by bismuth oxide and pseu-do-perovskite layers. They have a good ionic conductivity, which is beneficial for various photo-catalyzed reactions. Here, we synthesized ultra-thin nanosheets of two different Aurivillius oxides, Bi2WO6 (BWO) and Bi2MoO6 (BMO), by using a hard-template process. All materials were characterized through XRD, TEM, FTIR, TGA/DSC, DLS/ELS, DRS, UV-Vis. Band gap material (Eg) and potential of the valence band (EVB) were calculated for BWO and BMO. In contrast to previous reports on the use of multi composite materials, a new procedure for photocatalytic efficient BMO nanosheets was developed. The procedure, with an additional step only, avoids the use of composite materials, improves crystal structure, and strongly reduces impurities. BWO and BMO were used as photocatalysts for the degradation of the water pollutant dye malachite green (MG). MG removal kinetics was fitted with Langmuir-Hinshelwood model obtaining a kinetic constant k = 7.81 × 10-2 min-1 for BWO and k = 9.27 × 10-2 min-1 for BMO. Photocatalytic dye degradation was highly effective, reaching 89% and 91% MG removal for BWO and BMO, respectively. A control experiment, carried out in the absence of light, allowed to quantify the contribution of adsorption to MG removal process. Adsorption contributed to MG removal by a 51% for BWO and only by a 19% for BMO, suggesting a different degradation mechanism for the two photocatalysts. The advanced MG degradation process due to BMO is likely caused by the high crystallinity of the material synthetized with the new procedure. Reuse tests demonstrated that both photocatalysts are highly active and stable reaching a MG removal up to 95% at the 10th reaction cycle. These results demonstrate that BMO nanosheets, synthesized with an easy additional step, achieved the best degradation performance, and can be successfully used for environmental remediation applications.

Pomegranate Punica granatum peel waste as a naked-eye natural colorimetric sensor for the detection and determination of Fe+3 and I- ions in water

The utilization of renewable and abundant agricultural waste such as Pomegranate (Punica granatum L.) peel extract has been developed wherein a simple extraction of dried peel in water offered a natural sensor; ensuing yellowish solution comprising phenolic compounds reacted explicitly to detect Fe⁺³ and I^- solutions by naked-eye. The UV-Vis absorption spectrum of the resulting extracted mixture was drastically changed toward the longer wavelengths only after the addition of the Fe³⁺ and I^- while there was no discernible spectral change due to the addition of a broad range of other common cations and anions. In the case of Fe³⁺ and I^-, the transformation can be followed by the naked eye in the concentration range of 5 × 10^-4 M and 1 × 10^-2 M, respectively. An acceptable and reasonable detection with 47.05426 μM efficiency was attained in comparison to other Fe³⁺ indicators such as ferroin.