Ozone disinfection of chlorine-resistant bacteria in drinking water

Optimizing ozone treatment for pathogen removal and disinfection by-product control for potable reuse at pilot-scale

Reclaimed water poses environmental and human health risks due to residual organic micropollutants and pathogens. Ozonation of reclaimed water to control pathogens and trace organics is an important step in advanced water treatment systems for potable reuse of reclaimed water. Ensuring efficient pathogen reduction while controlling disinfection byproducts remains a significant challenge to implementing ozonation in reclaimed water reuse applications. This study aimed to investigate ozonation conditions using a plug flow reactor (PFR) to achieve effective pathogen removal/inactivation while minimizing bromate and N-Nitrosodimethylamine (NDMA) formation. The pilot scale study was conducted using three doses of ozone (0.7, 1.0 and 1.4 ozone/total organic carbon (O3/TOC) ratio) to determine the disinfection performance using actual reclaimed water. The disinfection efficiency was assessed by measuring total coliforms, Escherichia coli (E. coli), Pepper Mild Mottle Virus (PMMoV), Tomato Brown Rugose Fruit Virus (ToBRFV) and Norovirus (HNoV). The ozone CT values ranged from 1.60 to 13.62 mg min L-1, resulting in significant reductions in pathogens and indicators. Specifically, ozone treatment led to concentration reductions of 2.46-2.89, 2.03-2.18, 0.46-1.63, 2.23-2.64 and > 4 log for total coliforms, E. coli, PMMoV, ToBRFV, and HNoV, respectively. After ozonation, concentrations of bromate and NDMA increased, reaching levels between 2.8 and 12.0 μg L-1, and 28-40.0 ng L-1, respectively, for average feed water bromide levels of 86.7 ± 1.8 μg L-1 and TOC levels of 7.2 ± 0.1 mg L-1. The increases in DBP formation were pronounced with higher ozone dosages, possibly requiring removal/control in subsequent treatment steps in some potable reuse applications.

Assessment of microorganisms in drinking water disinfected by catalytic ozonation with fluorinated ceramic honeycomb and NaClO disinfectants under laboratory and pilot conditions

While sodium hypochlorite (NaClO) has long been used to disinfect drinking water, concerns have risen over its use due to causing potentially hazardous byproducts. Catalytic ozonation with metal-free catalysts has attracted increasing attention to eliminate the risk of secondary pollution of byproducts in water treatment. Here, we compared the disinfection efficiency and microbial community of catalytic ozone with a type of metal-free catalyst fluorinated ceramic honeycomb (FCH) and NaClO disinfectants under laboratory- and pilot-scale conditions. Under laboratory conditions, the disinfection rate of catalytic ozonation was 3∼6-fold that of ozone when the concentration of Escherichia coli was 1 × 106 CFU/ml, and all E. coli were killed within 15 s. However, 0.65 mg/L NaClO retained E. coli after 30 min using the traditional culturable approach. The microorganism inactivation results of raw reservoir water disinfected by catalytic ozonation and ozonation within 15 s were incomparable based on the cultural method. In pilot-scale testing, catalytic ozonation inactivated all environmental bacteria within 4 min, while 0.65 mg/L NaClO could not achieve this success. Both catalytic ozonation and NaClO-disinfected methods significantly reduced the number of microorganisms but did not change the relative abundances of different species, i.e., bacteria, viruses, eukaryotes, and archaea, based on metagenomic analyses. The abundance of virulence factors (VFs) and antimicrobial resistance genes (ARGs) was detected few in catalytic ozonation, as determined by metagenomic sequencing. Some VFs or ARGs, such as virulence gene 'FAS-II' which was hosted by Mycobacterium_tuberculosis, were detected solely by the NaClO-disinfected method. The enriched genes and pathways of cataO3-disinfected methods exhibited an opposite trend, especially in human disease, compared with NaClO disinfection. These results indicated that the disinfection effect of catalytic ozone is superior to NaClO, this finding contributed to the large-scale application of catalytic ozonation with FCH in practical water treatment.

A liquid culture method assisted by ATP analysis for accelerating laboratory experiments on ultraviolet disinfection of airborne bacteria

The solid culture method for measuring the efficiency of ultraviolet (UV) disinfection of airborne bacteria is time-consuming, typically taking 12-48 h. To expedite such experiments, this study proposed a liquid culture method assisted by adenosine triphosphate (ATP) analysis, as a liquid culture is faster than a solid culture, and measurement of ATP does not require waiting for visible colonies to form. Escherichia coli (E. coli) was used as the experimental bacterium. This study first compared the log reduction of bacteria in liquid as measured by the proposed method and by the traditional solid culture method. The minimum liquid culture time was determined for different bacterial concentration ranges. Finally, the feasibility of the proposed method was validated by UV disinfection experiments on airborne bacteria. The results indicated that the proposed method measured a similar log reduction to that of the solid culture method in liquid experiments. The minimum liquid culture time for E. coli in 105-106 colony forming units (CFU)/mL was 2 h. The validation experiments demonstrated that the proposed method is capable of measuring the UV disinfection efficiency of airborne bacteria. The proposed method can accelerate laboratory experiments on UV disinfection of airborne bacteria, which in turn can support the effective design and utilization of UV disinfection in real life.

Comprehensive assessment of chlorination disinfection on microplastic-associated biofilms

Chlorination on microplastic (MP) biofilms was comprehensively investigated with respect to disinfection efficiency, morphology, and core microbiome. The experiments were performed under various conditions: i) MP particles; polypropylene (PP) and polystyrene (PS), ii) MP biofilms; Escherichia coli for single-species and river water microorganisms for multiple-species, iii) different chlorine concentrations, and iv) different chlorine exposure periods. As a result, chlorination effectively inactivated the MP biofilm microorganisms. The disinfection efficiency increased with increasing the free chlorination concentration and exposure periods for both single- and multiple-species MP biofilms. The multiple-species MP biofilms were inactivated 1.3-6.0 times less than single-species MP biofilms. In addition, the PP-MP biofilms were more vulnerable to chlorination than the PS-MP biofilms. Morphology analysis verified that chlorination detached most MP biofilms, while a small part still remained. Interestingly, chlorination strongly changed the biofilm microbiome on MPs; the relative abundance of some microbes increased after the chlorination, suggesting they could be regarded as chlorine-resistant bacteria. Some potential pathogens were also remained on the MP particles after the chlorination. Notably, chlorination was effective in inactivating the MP biofilms. Further research should be performed to evaluate the impacts of residual MP biofilms on the environment.

Mechanism of antibiotic resistance spread during sub-lethal ozonation of antibiotic-resistant bacteria with different resistance targets

The increase and spread of antibiotic-resistant bacteria (ARB) in aquatic environments and the dissemination of antibiotic resistance genes (ARGs) greatly impact environmental and human health. It is necessary to understand the mechanism of action of ARB and ARGs to formulate measures to solve this problem. This study aimed to determine the mechanism of antibiotic resistance spread during sub-lethal ozonation of ARB with different antibiotic resistance targets, including proteins, cell walls, and cell membranes. ARB conjugation and transformation frequencies increased after exposure to 0-1.0 mg/L ozone for 10 min. During sub-lethal ozonation, compared with control groups not stimulated by ozone, the conjugative transfer frequencies of E. coli DH5α (CTX), E. coli DH5α (MCR), and E. coli DH5α (GEN) increased by 1.35-2.02, 1.13-1.58, and 1.32-2.12 times, respectively; the transformation frequencies of E. coli DH5α (MCR) and E. coli DH5α (GEN) increased by 1.49-3.02 and 1.45-1.92 times, respectively. When target inhibitors were added, the conjugative transfer frequencies of antibiotics targeting cell wall and membrane synthesis decreased 0.59-0.75 and 0.43-0.76 times, respectively, while that for those targeting protein synthesis increased by 1-1.38 times. After inhibitor addition, the transformation frequencies of bacteria resistant to antibiotics targeting the cell membrane and proteins decreased by 0.76-0.89 and 0.69-0.78 times, respectively. Cell morphology, cell membrane permeability, reactive oxygen species, and antioxidant enzymes changed with different ozone concentrations. Expression of most genes related to regulating different antibiotic resistance targets was up-regulated when bacteria were exposed to sub-lethal ozonation, further confirming the target genes playing a crucial role in the inactivation of different target bacteria. These results will help guide the careful utilization of ozonation for bacterial inactivation, providing more detailed reference information for ozonation oxidation treatment of ARB and ARGs in aquatic environments.

Disinfection-residual bacteria (DRB) after chlorine dioxide treatment: Microbial community structure, regrowth potential, and secretion characteristics

This study investigates the effects of chlorine dioxide (ClO2) disinfection on the community structure, regrowth potential, and metabolic product secretion of disinfection-residual bacteria (DRB) in secondary effluent (SE), denitrification filter effluent (DFE), and ultrafiltration effluent (UE). Results show that ClO2 effectively reduces bacteria in SE and UE, achieving log removal values exceeding 3 at 1 mg/L within 30 min. A salient positive correlation (R2 > 0.95) exists between changes in total fluorescence intensity and disinfection efficacy. Post-treatment, Acinetobacter abundance increased in SE, while Pseudomonas decreased in DFE and UE. At lower ClO2 concentrations, Staphylococcus, Mycobacterium, Aeromonas, and Lactobacillus increased in DFE, but decreased at higher concentrations. After storage, bacterial counts in disinfected samples exceeded those in the control group, surpassing 105 CFU/mL. Despite an initial decline, species richness and evenness partially recovered but remained lower than control levels. Culturing DRB for 72 h showed elevated extracellular polymeric substances (EPS) secretion, quantified as total organic carbon (TOC), ranging from 5 to 27 mg/L, with significantly higher EPS in the disinfection group. Parallel factor analysis with self-organizing maps (PARAFAC-SOM) effectively differentiated water sample types and EPS fluorescent substances, underscoring the potential of three-dimensional fluorescence as an indirect measure of ClO2 disinfection efficacy.

Systematic investigation and modeling prediction of virus inactivation by ozone in wastewater: Decoupling the matrix effects

Water disinfection is undoubtedly regarded as a critical step in ensuring the water safety for human consumption, and ozone is widely used as a highly effective disinfectant for the control of pathogenic microorganisms in water. Although the diminished ozone efficiencies in complex water matrices have been widely reported, the specific extent to which individual components of matrix act on the virus inactivation by ozone remains unclear, and effective methodologies to predict the comprehensive effects of various factors are needed. In this study, the decoupled impact of the intricate water matrix on the ozone inactivation of viruses was systematically investigated and assessed from a simulative perspective. The concept of "equivalent ozone depletion rate constant" (k') was introduced to quantify the influence of different species, and a kinetic model was developed based on the k' values for simulating the ozone inactivation processes in complex matrix. The mechanisms through which diverse species influenced the ozone inactivation effectiveness were identified: 1) competition effects (k' = 105∼107 M-1s-1), including organic matters and reductive ions (SO32-, NO2-, and I-), which were the most influential species inhibiting the virus inactivation; 2) shielding effects (k' = 103∼104 M-1s-1), including Ca2+, Mg2+, and kaolin; 3) insignificant effects (k' = 0∼1 M-1s-1), including Cl-, SO42-, NO3-, NH4+, and Br-; 4) promotion effects (k' = ∼-103 M-1s-1), including CO32- and HCO3-. Prediction of ozone disinfection efficiency and evaluation of species contribution under complex aquatic matrices were successfully realized utilizing the model. The systematic understanding and methodologies developed in this research provide a reliable framework for predicting ozone inactivation efficiency under complex matrix, and a potential tool for accurate disinfectant dosage determination and interfering factors control in actual wastewater treatment processes.

Study on the inactivation effect and mechanism of EGCG disinfectant on Bacillus subtilis

The widespread use of chlorine-based disinfectants in drinking water treatment has led to the proliferation of chlorine-resistant bacteria and the risk of disinfection byproducts (DBPs), posing a serious threat to public health. This study aims to explore the effectiveness and potential applications of epigallocatechin gallate (EGCG) against chlorine-resistant Bacillus and its spores in water, providing new insights for the control of chlorine-resistant bacteria and improving the biological stability of distribution systems. The inactivation effects of EGCG on Bacillus subtilis (B. subtilis) and its spores were investigated using transmission electron microscopy, ATP measurement, and transcriptome sequencing analysis to determine changes in surface structure, energy metabolism, and gene expression levels, thereby elucidating the inactivation mechanism. The results demonstrate the potential application of EGCG in continuously inhibiting chlorine-resistant B. subtilis in water, effectively improving the biological stability of the distribution system. However, EGCG is not suitable for treating raw water with high spore content and is more suitable as a supplementary disinfectant for processes with strong spore removal capabilities, such as ozone, ultraviolet, or ultrafiltration. EGCG exhibits a disruptive effect on the morphological structure and energy metabolism of B. subtilis and suppresses the synthesis of substances, energy metabolism, and normal operation of the antioxidant system by inhibiting the expression of multiple genes, thereby achieving the inactivation of B. subtilis.

The resistance change and stress response mechanisms of chlorine-resistant bacteria under microplastic stress in drinking water distribution system

The presence of both chlorine-resistant bacteria (CRB) and microplastics (MPs) in drinking water distribution systems (DWDS) poses a threat to water quality and human health. However, the risk of CRB bio evolution under the stress of MPs remains unclear. In this study, polypropylene (PP) and polyethylene (PE) were selected to study the adsorption and desorption behavior of sulfamethoxazole (SMX), and it was clear that MPs had the risk of carrying pollutants into DWDS and releasing them. The results of the antibiotic susceptibility test and disinfection experiment confirmed that MPs could enhance the resistance of CRB to antibiotics and disinfectants. Bacteria epigenetic resistance mechanisms were approached from multiple perspectives, including physiological and biochemical characteristics, as well as molecular regulatory networks. When MPs enter DWDS, CRB could attach to the surface of MPs and directly interact with both MPs and the antibiotics they release. This attachment process promoted changes in the composition and content of extracellular polymers (EPS) within cells, enhanced surface hydrophobicity, stimulated oxidative stress function, and notably elevated the relative abundance of certain antibiotic resistance genes (ARGs). This study elucidates the mechanism by which MPs alter the intrinsic properties of CRB, providing valuable insights into the effective avoidance of biological risks to water quality during CRB evolution.

MnO2-based capacitive system enhances ozone inactivation of bacteria by disrupting cell membrane

The application of ozone (O3) disinfection has been hindered by its low solubility in water and the formation of disinfection by-products (DBPs). In this study, capacitive disinfection is applied as a pre-treatment for O3 oxidation, in which manganese dioxide with a rambutan-like hollow spherical structure is used as the electrode to increase the charge density on the electrode surface. When a voltage is applied, the negative-charged microbes are attracted to the electrodes and killed by electrical interactions. The contact between microbes and capacitive electrodes leads to changes in cell permeability and burst of reactive oxygen species, thereby promoting the diffusion of O3 into the cells. After O3 penetrates the cell membrane, it can directly attack the cytoplasmic constituents, accelerating fatal and irreversible damage to pathogens. As a result, the performance of the capacitance-O3 process is proved better than the direct sum of the two individual process efficiencies. The design of capacitance-O3 system is beneficial to reduce the ozone dosage and DBPs with a broader inactivation spectrum, which is conducive to the application of ozone in primary water disinfection.

Comparative analysis of chlorine-resistant bacteria after chlorination and chloramination in drinking water treatment plants

Chlorine-resistant bacteria (CRB) in drinking water treatment plants (DWTPs) jeopardize water quality and pose a potential risk to human health. However, the specific response of CRB to chlorination and chloramination remains uncharacterized. Therefore, we analyzed 16 S rRNA sequencing data from water samples before and after chlorination and chloramination taken between January and December 2020. Proteobacteria and Firmicutes dominated all finished water samples. After chloramination, Acinetobacter, Pseudomonas, Methylobacterium, Ralstonia, and Sphingomonas were the dominant CRB, whereas Ralstonia, Bacillus, Acinetobacter, Pseudomonas, and Enterococcus were prevalent after chlorination. Over 75% of the CRB e.g. Acinetobacter, Pseudomonas, Bacillus, and Enterococcus were shared between the chlorination and chloramination, involving potentially pathogens, such as Acinetobacter baumannii and Pseudomonas aeruginosa. Notably, certain genera such as Faecalibacterium, Geobacter, and Megasphaera were enriched as strong CRB after chloramination, whereas Vogesella, Flavobacterium, Thalassolituus, Pseudoalteromonas, and others were enriched after chlorination according to LEfSe analysis. The shared CRB correlated with temperature, pH, and turbidity, displaying a seasonal pattern with varying sensitivity to chlorination and chloramination in cold and warm seasons. These findings enhance our knowledge of the drinking water microbiome and microbial health risks, thus enabling better infectious disease control through enhanced disinfection strategies in DWTPs.

Performance and mechanisms of zero valent iron enhancing short-chain fatty acids production during thermophilic anaerobic fermentation of waste activated sludge

This work first explored the feasibility and possible mechanisms of zero valent iron (ZVI) pretreatment on the generation of short-chain fatty acids (SCFAs) during thermophilic anaerobic fermentation of waste activated sludge (WAS). Results showed that ZVI enhanced the quantity of SCFAs. On Day 6, the SCFAs production reached 455.84 ± 47.88 mg COD/g VSS at 5 g/L of ZVI addition, which increased by 63.80 % relative to control. The presence of ZVI can effectively promote butyric-based fermentation. ZVI accelerated the destruction of extracellular polymeric substances (EPS) and interior sludge cells, as well as improved biodegradation of soluble organics. Also, ZVI enhanced key enzyme activities (i.e., BK and CoA-), thus promoting degradation rates of acidogenesis (6.30 ± 0.84 mg/(gVSS·h) in glucose) and acetogenesis (74.63 ± 0.29 mg/(gVSS·h) in butyrate). Compared to Fe(III), the contribution of Fe(II) was higher among the decomposition products of ZVI. Besides, ZVI favored Proteobacteria and Actinobacteria, which enhanced acetate formation and organic compounds disassimilation of the process, respectively. The abundance of Tepidiphilus, Thermobrachium and Tepidimicrobium was increased, indicating promoting the system stability of SCFAs production in thermophilic anaerobic fermentation.

Enhancing docosahexaenoic acid production in Aurantiochytrium species using atmospheric and room temperature plasma mutagenesis and comprehensive multi-omics analysis

Aurantiochytrium sp. belongs to marine heterotrophic single-cell protist, which is an important decomposer in marine ecosystem. Aurantiochytrium sp. has gained notoriety because of its ability to accumulate high-value docosahexaenoic acid (DHA), but the key factors of DHA synthesis were unclear at present. In this study, Atmospheric and Room Temperature Plasma technology was applied to the mutagenic breeding of Aurantiochytrium sp., and transcriptomics and proteomics were adopted to analyze the DHA-biosynthesis mechanism. According to the growth and DHA accumulation profiles, the mutant strain Aurantiochytrium sp. R2A35 was selected. The DHA content in total lipids was greatly improved from 49.39 % of the wild strain R2 to 63.69 % of the mutant strain. Moreover, the DHA content in the biomass of Aurantiochytrium sp. R2A35 as 39.72 % was the highest DHA productivity reported so far. The differentially expressed genes distinguished from transcriptome and the TMT-identified differential proteins distinguished from proteome confirmed that the expression of acetyl-CoA carboxylase and ketoacyl reductase was up-regulated by 4.78-fold and 6.95-fold, respectively and the fatty acid synthase was concurrently down-regulated by 2.79-fold, so that more precursor was transported to the polyketide synthase pathway, thereby increasing the DHA yield in Aurantiochytrium sp. R2A35. This research would provide reference for the DHA metabolism process and contribute to the understanding of the decomposer - Aurantiochytrium sp. in marine ecosystems.

Assessing impacts of municipal wastewater treatment plant upgrades on bacterial hazard contributions to the receiving urban river using SourceTracker

Upgrading municipal wastewater treatment plants (MWTPs) has been implemented in many megacities of China to reduce the discharges of nutrients and other pollutants and improve water quality of highly urbanized rivers. However, the contribution of MWTP discharge to bacterial hazards in the receiving rivers after upgrades has been largely unknown. In this study, high-throughput sequencing and shotgun metagenomics were applied to investigate the changes in the abundance, composition, potential risks, and contributions of bacteria and antibiotic resistance genes (ARGs) from effluent to receiving river after upgrading the third-largest MWTP in China with denitrification biofilters, ultrafiltration, ozonation, and disinfection processes. The annual loadings of total nitrogen and 27 types of pharmaceuticals were reduced by 42.4% ± 13.2% and 46.2% ± 15.4%, respectively. Bacterial biomass decreased from (3.58 ± 0.49) to (1.23 ± 0.27) × 107 16S rRNA gene copies/mL, and identified biomarkers in effluent and downstream shifted due to the adopted processes. Opportunistic pathogen bacteria downstream were also reduced. Although the relative abundance of total ARGs in MWTP effluent increased from 1.10 ± 0.02 to 2.19 ± 0.03 copies/16S rRNA gene after upgrades, that of total and high-risk ARGs downstream showed no significant difference. More importantly, the Bayesian-based SourceTracker method provided valuable insight by revealing that the contributions of MWTP discharge to downstream bacteria (from 44.2% ± 1.5%-31.4% ± 0.9%) and ARGs (from 61.2% ± 5.3%-47.6% ± 4.1%) were significantly reduced following the upgrades, indicating upgrading MWTP showed integrated benefits to the bacterial hazards in the receiving river. This study provides useful information for better control of bacterial hazard risks and operational strategy for the improvement of the urban aquatic ecosystem.

Inactivation of antibiotic-resistant bacteria in hospital wastewater by ozone-based advanced water treatment processes

The emergence and spread of antimicrobial resistance (AMR) continue on a global scale. The impacts of wastewater on the environment and human health have been identified, and understanding the environmental impacts of hospital wastewater and exploring appropriate forms of treatment are major societal challenges. In the present research, we evaluated the efficacy of ozone (O3)-based advanced wastewater treatment systems (O3, O3/H2O2, O3/UV, and O3/UV/H2O2) for the treatment of antimicrobials, antimicrobial-resistant bacteria (AMRB), and antimicrobial resistance genes (AMRGs) in wastewater from medical facilities. Our results indicated that the O3-based advanced wastewater treatment inactivated multiple antimicrobials (>99.9%) and AMRB after 10-30 min of treatment. Additionally, AMRGs were effectively removed (1.4-6.6 log10) during hospital wastewater treatment. The inactivation and/or removal performances of these pollutants through the O3/UV and O3/UV/H2O2 treatments were significantly (P < 0.05) better than those in the O3 and O3/H2O2 treatments. Altered taxonomic diversity of microorganisms based on 16S rRNA gene sequencing following the O3-based treatment showed that advanced wastewater treatments not only removed viable bacteria but also removed genes constituting microorganisms in the wastewater. Consequently, the objective of this study was to apply advanced wastewater treatments to treat wastewater, mitigate environmental pollution, and alleviate potential threats to environmental and human health associated with AMR. Our findings will contribute to enhancing the effectiveness of advanced wastewater treatment systems through on-site application, not only in wastewater treatment plants (WWTPs) but also in medical facilities. Moreover, our results will help reduce the discharge of AMRB and AMRGs into rivers and maintain the safety of aquatic environments.

Can microplastics and disinfectant resistance genes pose conceivable threats to water disinfection process?

Microplastic pollution in the environment has aroused widespread concerns, however, the potential environmental risks caused by excessive use of disinfectants are still unknown. Disinfectants with doses below the threshold can enhance the communication of resistance genes in pathogenic microorganisms, promoting the development and spread of antimicrobial activity. Problematically, the intensification of microplastic pollution and the increase of disinfectant consumption will become a key driving force for the growth of disinfectant resistance bacteria (DRB) and disinfectant resistance genes (DRGs) in the environment. Disinfection plays a crucial role in ensuring water safety, however, the presence of microplastics and DRGs seriously disturb the water disinfection process. Microplastics can reduce the concentration of disinfectant in the local environment around microorganisms and improve their tolerance. Microorganisms can improve their resistance to disinfectants or generate resistance genes via phenotypic adaptation, gene mutations, and horizontal gene transfer. However, very limited information is available on the impact of DRB and DRGs on disinfection process. In this paper, the contribution of microplastics to the migration and transmission of DRGs was analyzed. The challenges posed by the presence of microplastics and DRGs on conventional disinfection were thoroughly discussed. The knowledge gaps faced by relevant current research and further research priorities have been proposed in order to provide a scientific basis in the future.

Prevalence of antimicrobial resistance in a full-scale drinking water treatment plant

Antibiotic resistance in drinking water has received increasing attention in recent years. In this study, the occurrence and abundance of antibiotic resistance genes (ARGs) in a drinking water treatment plant (DWTP) was comprehensively investigated using metagenomics. Bioinformatics analysis showed that 381 ARG subtypes belonging to 15 ARG types were detected, and bacitracin had the highest abundance (from 0.26 × 10-2 to 0.86 copies/cell), followed by multidrug (from 0.57 × 10-1 to 0.47 copies/cell) and sulfonamide (from 0.83 × 10-2 to 0.35 copies/cell). Additionally, 933 ARG-carrying contigs (ACCs) were obtained from the metagenomic data, among which 153 contigs were annotated as pathogens. The most abundant putative ARG host was Staphylococcus (7.9%), which most frequently carried multidrug ARGs (43.2%). Additionally, 38 high-quality metagenome-assembled genomes (MAGs) were recovered, one of which was identified as Staphylococcus aureus (Bin.624) and harboured the largest number of ARGs (n = 16). Using the cultivation technique, 60 isolates were obtained from DWTP samples, and Staphylococcus spp. (n = 11) were found to be dominant in all isolates, followed by Bacillus spp. (n = 17). Antimicrobial susceptibility testing showed that most Staphylococcus spp. were multidrug resistant (MDR). These results deepen our understanding of the distribution profiles of ARGs and antibiotic resistant bacteria (ARB) in DWTPs for potential health risk evaluation. Our study also highlights the need for new and efficient water purification technologies that can be introduced and applied in DWTPs.

Use of Ozonized Water in the Prevention of Surgical Site Infection in Children Undergoing Cardiovascular Surgery

INTRODUCTION

Since the reduction of healthcare-associated infections has been a focus for quality patient care, this study aimed to evaluate the surgical site infection rate of children who underwent cardiovascular surgery after implementation of ozonized water system for hand and body hygiene allied to previously implemented preventive measures.

METHODS

Two uniformly comparable groups of pediatric patients underwent cardiovascular surgery. Group A (187) patients were operated prior to installation of ozonized water system (March 1 to August 31, 2019), and group B (214) patients were operated after installation of ozonized water system (October 1, 2019, to March 31, 2020). Ozonized water was used for professional hand hygiene and patient body hygiene.

RESULTS

There was statistical significance for surgical site infection reduction in group B (P=0.0289), with a relative risk of 0.560 (95% confidence interval = 0.298 to 0.920), inferring the risk of being diagnosed with surgical site infections in group B was 44% less than in group A. There was no statistical significance regarding mechanical ventilation time (P=0.1998) or mortality (P=0.4457).

CONCLUSION

Ozonized water for professional hand hygiene and patient body hygiene was an adjuvant combined with traditional preventive methods to reduce the risk of surgical site infection, although no impact on hospital stay or mortality was observed.

Inactivation of chlorine-resistant bacteria (CRB) via various disinfection methods: Resistance mechanism and relation with carbon source metabolism

With the widespread use of chlorine disinfection, chlorine-resistant bacteria (CRB) in water treatment systems have gained public attention. Bacterial chlorine resistance has been found positively correlated with extracellular polymeric substance (EPS) secretion. In this study, we selected the most suitable CRB controlling method against eight bacterial strains with different chlorine resistance among chloramine, ozone, and ultraviolet (UV) disinfection, analyzed the resistance mechanisms, clarified the contribution of EPS to disinfection resistance, and explored the role of carbon source metabolism capacity. Among all the disinfectants, UV disinfection showed the highest disinfection capacity by achieving the highest average and median log inactivation rates for the tested strains. For Bacillus cereus CR19, the strain with the highest chlorine resistance, 40 mJ/cm2 UV showed a 1.90 log inactivation, which was much higher than that of 2 mg-Cl2/L chlorine (0.67 log), 2 mg-Cl2/L chloramine (1.68 log), and 2 mg/L ozone (0.19 log). Meanwhile, the UV resistance of the bacteria did not correlate with EPS secretion. These characteristics render UV irradiation the best CRB controlling disinfection method. Chloramine was found to have a generally high inactivation efficiency for bacteria with high chlorine-resistance, but a low inactivation efficiency for low chlorine-resistant ones. Although EPS consumed up to 56.7% of chloramine which an intact bacterial cell consumed, EPS secretion could not explain chloramine resistance. Thus, chloramine is an acceptable CRB control method. Similar to chlorine, ozone generally selected high EPS-secreting bacteria, with EPS consuming up to 100% ozone. Therefore, ozone is not an appropriate method for controlling CRB with high EPS secretion. EPS played an important role in all types of disinfection resistance, and can be considered the main mechanism for bacterial chlorine and ozone disinfection resistance. However, as EPS was not the main resistance mechanism in UV and chloramine disinfection, CRB with high EPS secretion were inactivated more effectively. Furthermore, carbon source metabolism was found related to the multiple resistance of bacteria. Those with low carbon source metabolism capacity tended to have higher multiple resistance, especially to chlorine, ozone, and UV light. Distinctively, among the tested gram-negative bacteria, in contrast to other disinfectants, chloramine resistance was negatively correlated with EPS secretion and positively correlated with carbon source metabolism capacity, suggesting a special disinfection mechanism.

Ag Nanoparticle and Ti-MOF Cooperativity for Efficient Inactivation of E. coli in Water

Because of the limitations of traditional chlorine-based bactericidal water treatment, such as the formation of disinfection byproducts (DBPs) and resistance to chlorine, novel approaches and materials are required for effective disinfection of water. This study focuses on the development of a new sterilization material, Ag/NH2-MIL-125(Ti), which was designed to effectively inactivate Escherichia coli in water. The effectiveness of the as-designed material stems from the synergistic interactions between Ag nanoparticles (NPs) and photoactive metal-organic frameworks (MOFs). In this complex material, the MOFs play a critical role in dispersing and isolating the Ag NPs, thus preventing undesirable aggregation during bacterial inactivation. Simultaneously, Ag NPs enhance the photocatalytic performance of the MOFs. Sterilization experiments demonstrate the remarkable rapid E. coli inactivation performance of Ag/NH2-MIL-125(Ti) under illuminated and nonilluminated conditions. Within 25 min of visible light exposure, the as-prepared material achieves a >7-log E. coli reduction. In addition, Ag/NH2-MIL-125(Ti) efficiently decomposes acetic acid, which is the main DBP precursor, under visible light irradiation. Mechanistic investigations revealed that •O2- and h+ were the primary active substances responsible for the inactivation of E. coli and the decomposition of acetic acid, respectively.

Peracetic acid disinfection induces antibiotic-resistant E. coli into VBNC state but ineffectively eliminates the transmission potential of ARGs

The occurrence of a viable but nonculturable (VBNC) state in antibiotic-resistant E. coli (AR E. coli) and inefficient degradation of their antibiotic resistance genes (ARGs) may cause potential health risks during disinfection. Peracetic acid (PAA) is an alternative disinfectant for replacing chlorine-based oxidants in wastewater treatment, and the potential of PAA to induce a VBNC state in AR E. coli and to remove the transformation functionality of ARGs were investigated for the first time. Results show that PAA exhibits excellent performance in inactivating AR E. coli (over 7.0-logs) and persistently inhibiting its regeneration. After PAA disinfection, insignificant changes in the ratio of living to dead cells (∼4%) and the level of cell metabolism, indicating that AR E. coli were induced into VBNC states. Unexpectedly, PAA was found to induce AR E. coli into VBNC state by destroying the proteins containing reactive amino acids at thiol, thioether and imidazole groups, rather than the result of membrane damage, oxidative stress, lipid destruction and DNA disruption in the conventional disinfection processes. Moreover, the result of poor reactivity between PAA and plasmid strands and bases confirmed that PAA hardly reduced the abundance of ARGs and damaged the plasmid's integrity. Transformation assays and real environment validation indicated that PAA-treated AR E. coli could release large abundance of naked ARGs with high-efficiency transformation functionality (∼5.4 × 10-4 - ∼8.3 × 10-6) into the environment. This study has significant environmental implications for assessing the transmission of antimicrobial resistance during PAA disinfection.

Study on the distribution characteristics and metabolic mechanism of chlorine-resistant bacteria in indoor water supply networks

The presence and attachment of chlorine-resistant bacteria on the surface of water distribution network will deteriorate water quality and threaten human health. Chlorination is critical in drinking water treatment to ensure the biosafety of drinking water. However, how disinfectants affect the structures of dominant flora during biofilm development and whether the changes are consistent with the free flora remain unclear. Therefore, we investigated changes in species diversity and relative abundance of different bacterial communities in planktonic and biofilm samples at different chlorine residual concentrations (blank, 0.3 mg/L, 0.8 mg/L, 2.0 mg/L and 4.0 mg/L), and the main reasons for the development of chlorine resistance in bacteria was also discussed. The results showed that the richness of microbial species in the biofilm was higher than that in planktonic microbial samples. In the planktonic samples, Proteobacteria and Actinobacteria were the dominant groups regardless of the chlorine residual concentration. For biofilm samples, the dominant position of Proteobacteria bacteria was gradually replaced by actinobacteria bacteria with the increase of chlorine residual concentration. In addition, at higher chlorine residual concentration, Gram-positive bacteria were more concentrated to form biofilms. There are three main reasons for the generation of chlorine resistance of bacteria: enhanced function of efflux system, activated bacterial self-repair system, and enhanced nutrient uptake capacity.

Kinetics and mechanisms of bacteria disinfection by performic acid in wastewater: In comparison with peracetic acid and sodium hypochlorite

Performic acid (PFA) has been increasingly used in wastewater disinfection due to its strong oxidizing ability and few disinfection byproducts. However, its disinfection pathways and mechanisms towards pathogenic bacteria disinfection are poorly understood. In this study, E. coli, S. aureus, and B. subtilis were inactivated using sodium hypochlorite (NaClO), PFA, and peracetic acid (PAA) in simulated turbid water and municipal secondary effluent. Cell culture-based plate counting showed that E. coli and S. aureus were extremely susceptible to NaClO and PFA and achieved a 4-log inactivation at CTs ≤ 1 mg/L·min with an initial disinfectant concentration of 0.3 mg/L. B. subtilis was much more resistant. At the initial disinfectant dose of 7.5 mg/L, PFA required CTs of 3-13 mg/L·min to achieve a 4-log inactivation. Turbidity negatively affected the disinfection. In the secondary effluent, the CTs required for PFA to achieve a 4-log inactivation of E. coli and B. subtilis were 6-12 times higher than those required in simulated turbid water, and a 4-log inactivation of S. aureus could not be achieved. PAA showed a much weaker disinfection ability than the other two disinfectants. The reaction pathways of E. coli inactivation by PFA included both direct and indirect reactions, in which the PFA molecule accounted for 73 %, and ·OH and peroxide radicals accounted for 20 % and 6 %, respectively. During PFA disinfection, E. coli cells were severely disintegrated, while the S. aureus cell exteriors remained mostly intact. B. subtilis was the least affected. Compared with cell culture-based analysis, the inactivation detected by flow cytometry was significantly lower. Viable but non-culturable bacteria after disinfection were believed to be primarily responsible for this inconsistency. This study suggested that PFA was able to control regular bacteria in wastewater, but it should be used with caution when treating recalcitrant pathogens.

Antidepressant exposure as a source of disinfectant resistance in waterborne bacteria

The emergence of disinfectant-resistant pathogens in water is a major threat to public health. However, whether human-consumed pharmaceuticals can induce bacterial resistance to disinfectants remains unclear. Herein, Escherichia coli was exposed to 12 antidepressants, and susceptibility of antidepressant-induced chloramphenicol (CHL)-resistant mutants to disinfectants was tested. Whole genome sequencing, global transcriptomic sequencing, and real-time quantitative polymerase chain reaction were used to elucidate the underlying mechanisms. We observed that duloxetine, fluoxetine, amitriptyline, and sertraline significantly increased the mutation frequency of E. coli against CHL by 15- to 2948-fold. The resultant mutants increased the average MIC₅₀ of sodium hypochlorite, benzalkonium bromide, and triclosan roughly 2- to 8-fold. Consistently, marRAB and acrAB-tolC genes, together with ABC transporter genes (e.g., yddA, yadG, yojI, and mdlA), were triggered to increase the efflux of disinfectants out of the cell, while ompF was inhibited, reducing disinfectant penetration into the cell. Additionally, the occurrence of DNA mutations in marR and acrR in the mutants was observed, potentially resulting in increased synthesis of the AcrAB-TolC pump. This study indicates that pharmaceutical exposure may create disinfectant-resistant bacteria, which may then be released into water systems, providing novel insights into the potential source of water-borne disinfectant-resistant pathogens.

In situ generation of highly localized chlorine by laser-induced graphene electrodes during electrochemical disinfection

Laser-induced graphene (LIG) has gained popularity for electrochemical water disinfection due to its efficient antimicrobial activity when activated with low voltages. However, the antimicrobial mechanism of LIG electrodes is not yet fully understood. This study demonstrated an array of mechanisms working synergistically to inactivate bacteria during electrochemical treatment using LIG electrodes, including the generation of oxidants, changes in pH-specifically high alkalinity associated with the cathode, and electro-adsorption on the electrodes. All these mechanisms may contribute to the disinfection process when bacteria are close to the surface of the electrodes where inactivation was independent of the reactive chlorine species (RCS); however, RCS was likely responsible for the predominant cause of antibacterial effects in the bulk solution (i.e., ≥100 mL in our study). Furthermore, the concentration and diffusion kinetics of RCS in solution was voltage-dependent. At 6 V, RCS achieved a high concentration in water, while at 3 V, RCS was highly localized on the LIG surface but not measurable in water. Despite this, the LIG electrodes activated by 3 V achieved a 5.5-log reduction in Escherichia coli (E.coli) after 120-min electrolysis without detectable chlorine, chlorate, or perchlorate in the water, suggesting a promising system for efficient, energy-saving, and safe electro-disinfection.

Use of ozonation technology to combat viruses and bacteria in aquatic environments: problems and application perspectives for SARS-CoV-2

COVID-19 is a global health threat with a large number of confirmed cases and deaths worldwide. Person-to-person transmission through respiratory droplets and contact with aerosol-infected surfaces are the main ways in which the virus spreads. However, according to the updated literature, the new coronavirus (SARS-CoV-2) has also been detected in aqueous matrices, with the main route of transmission being feces and masks from patients diagnosed with the disease. Given the emergence of public health and environmental protection from the presence of lethal viruses and bacteria, this review article aims to report the major challenges associated with the application of ozonation in water contaminated with viruses and bacteria, in order to clarify whether these communities can survive or infect after the disinfection process and if it is efficient. Available data suggest that ozonation is able to increase the inactivation effect of microorganisms by about 50% in the logarithmic range, reducing infectivity. In addition, the evidence-based knowledge reported in this article is useful to support water and sanitation safety planning and to protect human health from exposure to cited contaminants through water.

Proteomic analysis reveals mechanisms of mixed wastewater with different N/P ratios affecting the growth and biochemical characteristics of Chlorella pyrenoidosa

Effects of different nutrient ratios on the biochemical compositions of microalgae and the changes were rarely studied at the molecular level. In this study, the impacts of various nitrogen to phosphorus (N/P) ratios on growing of C. pyrenoidosa, as well as biochemical compositions and the metabolic regulation mechanism in mixed sewage, were investigated. The results suggested that 18 was optimal N/P ratio, while the dry weight (1.0 g/L), chlorophyll-a (Chla) (3.63 mg/L), and lipid production (0.28 g/L) were all the highest comparing with other groups. In contrast, the protein production (0.37 g/L) was the least. The nature of the regulatory mechanisms inthe metabolic pathways of these biochemical compositions was revealed by proteomic results, and there were 62 different expression proteins (DEPs) taken part in fatty acid and lipid biosynthesis metabolism (FA), amino acid biosynthesis metabolism (AA), photosynthesis (PHO), carbon fixation in photosynthetic organisms (CFP), and central carbon metabolism (CCM).

Environmental sporobiota: Occurrence, dissemination, and risks

Spore-forming bacteria known as sporobiota are widespread in diverse environments from terrestrial and aquatic habitats to industrial and healthcare systems. Studies on sporobiota have been mainly focused on food processing and clinical fields, while a large amount of sporobiota exist in natural environments. Due to their persistence and capabilities of transmitting virulence factors and antibiotic resistant genes, environmental sporobiota could pose significant health risks to humans. These risks could increase as global warming and environmental pollution has altered the life cycle of sporobiota. This review summarizes the current knowledge of environmental sporobiota, including their occurrence, characteristics, and functions. An interaction network among clinical-, food-related, and environment-related sporobiota is constructed. Recent and effective methods for detecting and disinfecting environmental sporobiota are also discussed. Key problems and future research needs for better understanding and reducing the risks of environmental sporobiota and sporobiome are proposed.

Ozone Decontamination of Medical and Nonmedical Devices: An Assessment of Design and Implementation Considerations

The control of infectious diseases can be improved via carefully designed decontamination equipment and systems. Research interest in ozone (a powerful antimicrobial agent) has significantly increased over the past decade. The COVID-19 pandemic has also instigated the development of new ozone-based technologies for the decontamination of personal protective equipment, surfaces, materials, and indoor environments. As this interest continues to grow, it is necessary to consider key factors affecting the applicability of lab-based findings to large-scale systems utilizing ozone. In this review, we present recent developments on the critical factors affecting the successful deployments of industrial ozone technologies. Some of these include the medium of application (air or water), material compatibility, efficient circulation and extraction, measurement and control, automation, scalability, and process economics. We also provide a comparative assessment of ozone relative to other decontamination methods/sterilization technologies and further substantiate the necessity for increased developments in gaseous and aqueous ozonation. Modeling methodologies, which can be applied for the design and implementation of ozone contacting systems, are also presented in this review. Key knowledge gaps and open research problems/opportunities are extensively covered including our recommendations for the development of novel solutions with industrial importance.

UV Disinfection Robots: A Review

The novel coronavirus (COVID-19) pandemic has completely changed our lives and how we interact with the world. The pandemic has brought about a pressing need to have effective disinfection practices that can be incorporated into daily life. They are needed to limit the spread of infections through surfaces and air, particularly in public settings. Most of the current methods utilize chemical disinfectants, which can be laborious and time-consuming. Ultraviolet (UV) irradiation is a proven and powerful means of disinfection. There has been a rising interest in the implementation of UV disinfection robots by various public institutions, such as hospitals, long-term care homes, airports, and shopping malls. The use of UV-based disinfection robots could make the disinfection process faster and more efficient. The objective of this review is to equip readers with the necessary background on UV disinfection and provide relevant discussion on various aspects of UV robots.

Ozone application in different industries: A review of recent developments

Ozone - a powerful antimicrobial agent, has been extensively applied for decontamination purposes in several industries (including food, water treatment, pharmaceuticals, textiles, healthcare, and the medical sectors). The advent of the COVID-19 pandemic has led to recent developments in the deployment of different ozone-based technologies for the decontamination of surfaces, materials and indoor environments. The pandemic has also highlighted the therapeutic potential of ozone for the treatment of COVID-19 patients, with astonishing results observed. The key objective of this review is to summarize recent advances in the utilisation of ozone for decontamination applications in the above-listed industries while emphasising the impact of key parameters affecting microbial reduction efficiency and ozone stability for prolonged action. We realise that aqueous ozonation has received higher research attention, compared to the gaseous application of ozone. This can be attributed to the fact that water treatment represents one of its earliest applications. Furthermore, the application of gaseous ozone for personal protective equipment (PPE) and medical device disinfection has not received a significant number of contributions compared to other applications. This presents a challenge for which the correct application of ozonation can mitigate. In this review, a critical discussion of these challenges is presented, as well as key knowledge gaps and open research problems/opportunities.

Assessment of relationship between aging and contaminant-carryover for different filter layer of surgical mask under urban environmental stressors

Abundant disposable surgical masks (SMs) remain in the environment and continue to age under urban environmental stressors. This study aimed to investigate the aging characteristics of SMs and the effect of different aged layers of SMs on phenanthrene (PHE), tylosin (TYL), and sulfamethazine (SMT) under two different urban environmental stressors (UV and ozone). The results show that UV exposure causes more severe aging of the SM layers than ozone. The middle layer, made of melt-brown fabric, has displayed the highest degree of aging due to its smaller diameter and mechanical strength. The two-dimensional correlation spectroscopy (2D-COS) analysis reveals the different aging sequences of functional groups and three layers in aged SMs under the two urban environmental stressors. Whether the SMs are aged or not, the adsorptions of three organic pollutants on SMs are positively correlated with the octanol-water partition coefficient. Furthermore, except for the dominant hydrophobic interaction, aged SMs can promote the adsorption of three organic pollutants by accessory interactions (hydrogen bonding and partition), depending on their structures. These findings highlight the environmental effects of new microplastic (MP) sources and coexisting pollutants under the influence of COVID-19, which is helpful in accurately evaluating the biological toxicity of SMs.

Synergistic nanowire-assisted electroporation and chlorination for inactivation of chlorine-resistant bacteria in drinking water systems via inducing cell pores for chlorine permeation

The widespread use of chlorination (Cl₂) in drinking water systems causes the selection of chlorine-resistant bacteria commonly with dense extracellular polymeric substance (EPS) against chlorine permeation, posing significant threat to public health. Herein, a nanowire-assisted electroporation (EP) via locally enhanced electric field was combined with Cl₂ to construct the synergistic EP/Cl₂ disinfection, with the purposes of inducing cell pores for chlorine permeation and bacterial inactivation. The synergistic effects of EP/Cl₂ were observed for inactivation of chlorine-resistant Bacillus cereus (G+, 304 μg DOC-EPS/10⁹ CFU) and Aeromonas media (G-, 35.8 μg), and chlorine-sensitive Escherichia coli (G-, 5.1 μg) that were frequent occurrence in drinking water systems. The EP/Cl₂ enabled above 6 log B. cereus inactivation (undetectable live bacteria) at 1.5 V-EP and 0.9 mg/L-Cl₂, which was much higher than the individual EP (1.11 log) and Cl₂ (1.13 log) disinfection. The cell membrane integrity, intracellular free chlorine levels, and morphology analyses revealed that the electroporation-induced pores on cell wall/membrane destructed the bound EPS barrier for chlorine permeation, and the pore sizes were further enlarged by chlorine oxidation, hence facilitating bacterial inactivation via destroying the cell structures. The excellent disinfection performance for tap water and lake water also suggested its sound application potentials.

Nutrients removal by Olivibacter jilunii immobilized on activated carbon for aquaculture wastewater treatment: ppk1 gene and bacterial community structure

In this study, immobilized biological activated carbon (IBAC) mediated with Olivibacter jilunii (strain PAO-9) was utilized to treat aquaculture wastewater for nutrients removal. IBAC with strain PAO-9 could load the greatest ppk1 gene copy numbers (129524.6) per gram on activated carbon at 28 °C for 2 d in 120 rpm of stirring speed and 2 d in stationary condition. Moreover, the results about the nutrients removal and microbiology community structure showed that strain PAO-9 on IBAC could alter the structure and diversity of microbial communities and then promoted to remove the total phosphorus and total nitrogen of eel aquaculture wastewater. The highest total phosphorus, chemical oxygen demand, ammonia and total nitrogen of the wastewater treated by strain PAO-9 on IBAC were 96.1 %, 98.0 %, 100.0 % and 97.4 %, respectively. In all, O. jilunii PAO-9 immobilized activated carbon was a potential and effective approach to remove the nutrients of eel aquaculture wastewater.

Molecular ecological networks reveal the spatial-temporal variation of microbial communities in drinking water distribution systems

Microbial activity and regrowth in drinking water distribution systems is a major concern for water service companies. However, previous studies have focused on the microbial composition and diversity of the drinking water distribution systems (DWDSs), with little discussion on microbial molecular ecological networks (MENs) in different water supply networks. MEN analysis explores the potential microbial interaction and the impact of environmental stress, to explain the characteristics of microbial community structures. In this study, the random matrix theory-based network analysis was employed to investigate the impact of seasonal variation including water source switching on the networks of three DWDSs that used different disinfection methods. The results showed that microbial interaction varied slightly with the seasons but was significantly influenced by different DWDSs. Proteobacteria, identified as key species, play an important role in the network. Combined UV-chlorine disinfection can effectively reduce the size and complexity of the network compared to chlorine disinfection alone, ignoring seasonal variations, which may affect microbial activity or control microbial regrowth in DWDSs. This study provides new insights for analyzing the dynamics of microbial interactions in DWDSs.

Possibility of using ionizing radiation treated sludge from drinking water treatment plant as fertilizer in agriculture: Effects of aging

Using ionizing radiation in treating waste sludge from a drinking water treatment plant is a well-known technique. Sludge treated with ionizing radiation can be used as fertilizer in agriculture. In this paper, the effects of aging on the physicochemical characteristics, the content of microorganisms, molds, acrylamide, heavy metal concentration, and total nutrient content in waste sludge treated with e-beam and gamma irradiation were investigated. The possibility of using treated sludge as a fertilizer in agriculture was evaluated. It has been shown that the content of acrylamide in treated sludge after 15 months of storage does not exceed the limits for sludge to be used as fertilizer. If the sludge is stored in closed bags in a dark place, aging does not increase total microorganisms and molds. The research also showed that the sludge's physicochemical characteristics treated in this way do not decrease under the influence of aging. Finally, it has been shown that aging does not change the concentration of heavy metals and total nutrients in sludge treated by ionizing irradiation.

A novel aquatic worm (Limnodrilus hoffmeisteri) conditioning method for enhancing sludge dewaterability by decreasing filamentous bacteria

In this study, a novel aquatic worm conditioning method was proposed to enhance sludge dewaterability by reducing filamentous bacteria. The optimal treatment time was 4 days and the optimal sludge concentration was 5000 mg/L. Under these conditions, the sludge dewaterability was improved with CST of 16.69 s, reduction in sludge SRF of 48.95 %, and reduction in LfA of 58.23 %. After bio-conditioning, sludge flocs broke up by the aquatic worm predation. The absolute zeta potential decreased to -8.27 mV, and the particle size increased from 36.64 μm to 48.05 μm. Proteins, polysaccharides and other organic substances in sludge EPS and microbial cells were released, with the viscosity reduced to 1.16 mPa·s and the bound water converted into free water. Besides, the number and abundance of representative filamentous Chloroflexi decreased, resulting in the enhancement of sludge dewatering performance. Overall, the aquatic worm conditioning process can be divided into two steps: Sludge destruction by the aquatic worm predation and sludge re-coagulation by filamentous bacteria as a skeleton.

Sono-Enzymatically Embedded Antibacterial Silver-Lignin Nanoparticles on Cork Filter Material for Water Disinfection

Providing clean drinking water is a great challenge worldwide, especially for low-income countries where the access to safe water is limited. During the last decade, new biotechnological approaches have been explored to improve water management. Among them, the use of antimicrobial nanoparticles for designing innovative centralized and decentralized (point-of-use) water treatment systems for microbial decontamination has received considerable attention. Herein, antimicrobial lignin capped silver nanoparticles (AgLNP) were embedded on residual cork pieces using high-intensity ultrasound coupled with laccase-mediated grafting to obtain biofunctionalized nanomaterial. The developed AgLNP-coated cork proved to be highly efficient to drastically reduce the number of viable Gram-negative Escherichia coli and Gram-positive Staphylococcus aureus in liquid medium. Additionally, the coated-cork was characterized using FTIR-ATR spectroscopy and SEM imaging, and further used as a filter bed in a point-of-use device for water disinfection. The constructed water filtering system significantly reduced the amount of viable E. coli and resistant Bacillus cereus spores from filtered water operating at increasing residence times of 1, 4, 6, 16, 24, and 48 h. Therefore, the presented results prove that the obtained cork-based antimicrobial nanocomposite material could be used as a filtering medium for the development of water filtration system to control pathogen dissemination.

Global occurrence of SARS-CoV-2 in environmental aquatic matrices and its implications for sanitation and vulnerabilities in Brazil and developing countries

This paper includes a systematic review of the SARS-CoV-2 occurrence in environmental aquatic matrices and a critical sanitation analysis. We discussed the interconnection of sanitation services (wastewater, water supply, solid waste, and stormwater drainage) functioning as an important network for controlling the spread of SARS-CoV-2 in waters. We collected 98 studies containing data of the SARS-CoV-2 occurrence in aquatic matrices around the world, of which 40% were from developing countries. Alongside a significant number of people infected by the virus, developing countries face socioeconomic deficiencies and insufficient public investment in infrastructure. Therefore, our study focused on highlighting solutions to provide sanitation in developing countries, considering the virus control in waters by disinfection techniques and sanitary measures, including alternatives for the vulnerable communities. The need for multilateral efforts to improve the universal coverage of sanitation services demands urgent attention in a pandemic scenario.

An overview of nanomaterial-based novel disinfection technologies for harmful microorganisms: Mechanism, synthesis, devices and application

Harmful microorganism (e.g., new coronavirus) based infection is the most important security concern in life sciences and healthcare. This article aims to provide a state-of-the-art review on the development of advanced technology based on nanomaterial disinfection/sterilization techniques (NDST) for the first time including the nanomaterial types, disinfection techniques, bactericidal devices, sterilization products, and application scenarios (i.e., water, air, medical healthcare), with particular brief account of bactericidal behaviors referring to varied systems. In this emerging research area spanning the years from 1998 to 2021, total of ~200 publications selected for the type of review paper and research articles were reviewed. Four typical functional materials (namely type of metal/metal oxides, S-based, C-based, and N-based) with their development progresses in disinfection/sterilization are summarized with a list of synthesis and design. Among them, the widely used silver nanoparticles (AgNPs) are considered as the most effective bacterial agents in the type of nanomaterials at present and has been reported for inactivation of viruses, fungi, protozoa. Some methodologies against (1) disinfection by-products (DBPs) in traditional sterilization, (2) noble metal nanoparticles (NPs) agglomeration and release, (3) toxic metal leaching, (4) solar spectral response broadening, and (5) photogenerated e^-/h⁺ pairs recombination are reviewed and discussed in this field, namely (1) alternative techniques and nanomaterials, (2) supporter anchoring effect, (3) nonmetal functional nanomaterials, (4) element doping, and (5) heterojunction constructing. The feasible strategies in the perspective of NDST are proposed to involve (1) non-noble metal disinfectors, (2) multi-functional nanomaterials, (3) multi-component nanocomposite innovation, and (4) hybrid techniques for disinfection/sterilization system. It is promising to achieve 100% bactericidal efficiency for 10⁸ CFU/mL within a short time of less than 30 min.

Enhancing harvest of biodiesel-promising microalgae using Daphnia domesticated by amino acids

Mass production of microalgal biodiesel is hindered by microalgae harvesting efficiency and costs. In this study, Daphnia domesticated by amino acids were used to harvest microalgae via ingesting. The main factors (density of Daphnia, salinity, pH, light-environment, temperature and algal concentration) that were conducive to Daphnia feeding were optimized. Under the optimal condition, Microalgae-feeding Daphnia were domesticated by adding D-glutamic acid and L-cysteine as stimulating factors. After that, the ingestion rate of domesticated Daphnia increased by 24.93%. The presence of Daphnia as a predator can induce microalgae to mass into clusters. Combining Daphnia feeding and the inductive defense flocculation of microalgae, the harvesting rate of mixed algae (Chlorella pyrenoidosa and Scenedesmus obliquus) reached over 95% after 9 h. Overall, this work suggested that Daphnia feeding process is a green and economical approach for microalgae harvesting.

An Efficient, Multiplexed Strategy for Instant Detection of Bacterial Biomarker by a Lanthanide-Organic Material

Water contamination is a highly critical issue owing to its strong relationship to human health. In addition to chemical pollutants, microorganisms such as multiresistant pathogenic bacteria have received significant attention from the World Health Organization. The main problem associated with monitoring pathogenic bacteria in water is the interference from concomitant species and their low concentrations. To address this problem, we synthesized a bilanthanide-organic material as an efficient luminescence sensor for the detection of Pseudomonas aeruginosa, a representative bacterium, via its two unique biomarkers: 1-hydroxyphenazine (1-HX) and 2-aminoacetophenone (2-AA). This multiplexed sensing approach overcomes a common issue encountered by single-marker luminescence sensors that may report false positives due to coexisting species in the complex environment. High sensitivities and low limits of detection for 1-HX and 2-AA were obtained with very fast response time. The key structural factors governing the high-performance sensing function were revealed. This work provides an alternative route for the effortless and instant detection of bacterial biomarkers in water.

Differentiation of DNA or membrane damage of the cells in disinfection by flow cytometry

Recently, the viabilities changes of fungal spores in the water supply system during different disinfection processes have been revealed. SYBR Green I (SG), a nucleic acid stain, its fluorescence intensity is correlated with the amount of double-stranded DNA. This study established a new method through successive SG-SG-PI staining (PI: Propidium Iodide) with flow cytometry (FCM). It could successfully distinguish DNA damage and membrane damage of fungal spores, clearly elucidating the intrinsic disinfection mechanism during the chemical disinfection. This method was briefly described as follows: firstly, (1) the fungal spores were stained with SG and washed by centrifugation; and then, (2) the washed spores were treated with disinfectants and terminated; after that, (3) the disinfected spores were re-stained with SG and analyzed by FCM; finally, (4) the SG re-stained spores were stained with PI and analyzed by FCM. The percentages of spores with DNA damage and membrane damage were determined by the fluorescence intensity obtained from steps (3) and (4), respectively. The repeatability and applicability of this developed method were confirmed. It was further applied to explore the inactivation mechanism during chlorine-based disinfection, and results demonstrated that chloramine attacked the DNA more seriously than the membrane, while chlorine and chlorine dioxide worked in a reverse way.

Surface-enhanced Raman spectroscopy enabled evaluation of bacterial inactivation

An improved understanding of bacterial inactivation mechanisms will provide useful insights for infectious disease control and prevention. We evaluated bacterial response to several inactivation methods using surface-enhanced Raman spectroscopy (SERS). The results indicate that changes in the SERS signal are highly related to cellular disruption and that cellular changes arising after cell inactivation cannot be ignored. The membrane integrity of heat and the combination of UV₂₅₄ and free chlorine (UV₂₅₄/chlorine) treated Pseudomonas syringae (P. syringae) cells were severely disrupted, leading to significantly increased peak intensities. Conversely, ethanol treated bacteria exhibited intact cell morphologies and the SERS spectra remained virtually unchanged. On the basis of time dependent SERS signals, we extracted dominant SERS patterns. Peaks related to nucleic acids accounted for the main changes observed during heat, UV₂₅₄, and UV₂₅₄/chlorine treatment, likely due to their outward diffusion from the cell cytoplasm. For free chlorine treated P. syringae, carbohydrates and proteins on the cell membrane were denatured or lost, resulting in a decrease in related peak intensities. The nucleobases were likely oxidized when treated with UV₂₅₄ and chlorine, thus leading to shifts in the related peaks. The generality of the method was verified using two additional bacterial strains: Escherichia coli and Bacillus subtilis as well as in different water matrices. The results suggest that SERS spectral analysis is a promising means to examine bacterial stress response at the molecular level and has applicability in diverse environmental implementations.

Control for chlorine resistant spore forming bacteria by the coupling of pre-oxidation and coagulation sedimentation, and UV-AOPs enhanced inactivation in drinking water treatment

Spore forming bacteria (SFB) are strongly chlorine resistant. Their presence in drinking water may cause diseases and pose threat to public health. Three SFB strains, i.e. Bacillus alvei, Bacillus cereus, and Lysinibacillus fusiformis, were isolated and identified from the finished water of a drinking water treatment plant where bacteria colonies occasionally reached the limit value. Due to their chlorine resistance, a SFB control strategy coupling pre-oxidation, coagulation sedimentation, and UV-AOPs inactivation in water treatment process was studied in lab scale. Five minutes pre-oxidation treatment by applying Cl₂ and ClO₂ induced remarkable spore transformation. Longer pre-oxidation exposure time didn't have apparent improvement. Cl₂ and ClO₂ dosages of 0.9 mg/L and 0.5 mg/L were suggested, respectively. The formed spores can be efficiently removed by the following coagulation sedimentation treatment. At a suggested dosage combination of 20 mg/L PAC and 0.08 mg/L PAM, spore removal efficiency reached about 3.15-lg. Comparing to applying sole UV irradiation, enhanced UV inactivation by adding 0.1 mM H₂O₂, or Cl₂, or peroxymonosulfate (PMS) substantially improved the inactivation of the most chlorine resistant SFB strain, Lysinibacillus fusiformis. UV-AOPs stably achieved 2-lg inactivation rate at UV dosage of 40 mJ/cm². UV/H₂O₂, UV/Cl₂ and UV/PMS inactivation kinetically enhanced 1.20 times, 1.36 times and 1.91 times over sole UV irradiation. Intracellular DNA and ATP leakages were detected, and remarkable damages of Lysinibacillus fusiformis cells' surface and ultrastructure were observed. These findings evidenced cell wall and cell membrane destructions, guaranteeing substantial SFB cells inactivation. This study was carried out based on three SFB strains isolated from a finished water, and common engineering practical operations. By providing engineeringly relevant references, the outcomes obtained would be helpful for dealing with SFB outbreak risk in drinking water treatment.

Ozone in wineries and wine processing: A review of the benefits, application, and perspectives

Ozone (O₃ ) is an emerging eco-friendly technology that has been widely used in the beverage industry due to its broad spectrum of usages, such as fermentation, microbial inactivation, Clean-in-Place (CIP) systems, and postharvest treatment. Wine is among the most financially profitable sectors of the beverage industry. Ozone technology as an alternative approach to conventional methods to inhibit microbes in wine processing and wineries has attracted researchers' attention as this emerging technology will probably play important roles in wineries in the future. This review discusses the prospective applications of ozone in winemaking and wineries and elaborates on ozone's antimicrobial effects on the control of the broad spectrum of microorganisms during wine processing. Also, this paper provides discussions on its effects of O₃  on wine quality and the benefits this emerging technology can bring to wineries. Ozone treatments can improve yeast fermentation by impacting the yeast ecology of postharvested wine grapes, mainly by affecting apiculate yeasts and adjusting the population of undesirable yeasts, such as Brettanomyces spp., during the fermentation process. Furthermore, ozone treatment may enhance wine's anthocyanin concentration, physicochemical properties, color, pH, oxidative stability, and concentration of pleasant volatile compounds and esters. This article presents important information to have a better understanding of the impact of ozone treatment on different stages of wine preparation.

Exploring the use of flow cytometry for understanding the efficacy of disinfection in chlorine contact tanks

A pilot scale chlorine contact tank (CCT) with flexible baffling was installed at an operational water treatment plant (WTP), taking a direct feed from the outlet of the rapid gravity filters (RGF). For the first time, disinfection efficacy was established by direct microbial monitoring in a continuous reactor using flow cytometry (FCM). Disinfection variables of dose, time, and hydraulic efficiency (short circuiting and dispersion) were explored following characterisation of the reactor's residence time distributions (RTD) by tracer testing. FCM enabled distinction to be made between changes in disinfection reactor design where standard culture-based methods could not. The product of chlorine concentration (C) and residence time (t) correlated well with inactivation of microbes, organisms, with the highest cell reductions (N/N₀) reaching <0.025 at Ct_x¯ of 20 mg.min/L and above. The influence of reactor geometry on disinfection was best shown from the Ct₁₀. This identified that the initial level of microbial inactivation was higher in unbaffled reactors for low Ct₁₀ values, although the highest levels of inactivation of 0.015 could only be achieved in the baffled reactors, because these conditions enabled the highest Ct₁₀ values to be achieved. Increased levels of disinfection were closely associated with increased formation of the trihalomethane disinfection by-products. The results highlight the importance of well-designed and operated CCT. The improved resolution afforded by FCM provides a tool that can dynamically quantify disinfection processes, enabling options for much better process control.

Interaction Mechanisms and Application of Ozone Micro/Nanobubbles and Nanoparticles: A Review and Perspective

Ozone micro/nanobubbles with catalytic processes are widely used in the treatment of refractory organic wastewater. Micro/nanobubble technology overcomes the limitations of ozone mass transfer and ozone utilization in the application of ozone oxidation, and effectively improves the oxidation efficiency of ozone. The presence of micro/nanobubbles keeps the catalyst particles in a dynamic discrete state, which effectively increases the contact frequency between the catalyst and refractory organic matter and greatly improves the mineralization efficiency of refractory organic matter. This paper expounds on the characteristics and advantages of micro/nanobubble technology and summarizes the synergistic mechanism of microbubble nanoparticles and the mechanism of catalyst ozone micro/nanobubble systems in the treatment of refractory organics. An interaction mechanism of nanoparticles and ozone microbubbles is suggested, and the proposed theories on ozone microbubble systems are discussed with suggestions for future studies on systems of nanoparticles and ozone microbubbles.