Exploring the fate of dissolved organic matter at the molecular level in the reactive electrochemical ceramic membrane system using fluorescence spectroscopy and FT-ICR MS

Unraveling the role of black soldier fly larvae in chicken manure conversion: Facilitating maturation and enhancing humification

Black soldier fly larvae (BSFL) have garnered considerable attention for their efficacy in mitigating waste management challenges. However, their potential in treating antibiotics contaminated chicken manure remains uncertain. This study investigates the physicochemical properties changes and nutrient dynamics during the composting of contaminated-chicken manure using BSFL. The results indicate that BSFL treatment reduces electrical conductivity (by 6.01-58.09 %), organic matter, and dissolved organic carbon content in chicken manure throughout the composting process, while maintaining a more stable pH value (pH ∼ 6.0-8.0). This is attributed to the consumption of organic matter by BSFL and the subsequent promotion of organic acid formation. Additionally, BSFL treatment improves the degree of aromatization of dissolved organic matter (DOM) in chicken manure and increases the proportions of fulvic acid (up to 48.77 %) and humic acid (maximally 14.27 %) within the DOM. The germination index and pot experiments indicated improved compost maturity and plant growth in BSFL-treated composts. Furthermore, BSFL meal demonstrated high protein and essential fatty acid content, highlighting its potential as a protein supplement in animal feed. This study underscores the efficacy of BSFL in enhancing compost quality and nutrient availability, offering a sustainable solution for waste management and animal feed production.

Indicative impacts of sludge properties and biological metabolic characteristics on high-rate contact stabilization process performance

Regarding curtailing carbon emissions in wastewater treatment, the high-rate contact stabilization (HiCS) process outperforms others in removing dissolved organic matter (DOM) but struggles with poor settling performance. To boost operation performance and clarify the correlation between process parameters, DOM variations, effluent quality, and microbial metabolism within the HiCS system, the impacts of sludge properties on sludge settlement and organic matter (OM) capture efficiency were explored, and soluble fluorescent components in the DOM and extracellular polymeric substances (EPS) were identified and scrutinized. Results unveil that the feast/famine (F/F) regime in the HiCS process predominantly governs sludge activation in the stabilization phase, influencing sludge properties such as morphology characteristics, biological activity, and EPS secretion. At the same hydraulic retention time, reducing the sludge retention time (SRT) led to looser and smaller activated sludge flocs, increased microbial activity, and higher EPS production, particularly protein content in loosely bound EPS (LB-PN), which adversely impacted settling performance. High-throughput sequencing revealed that richness and diversity of the microbial community decreased with SRT. Acidobacteriota and Patescibacteria, associated with nitrifying and denitrifying bacteria, significantly decreased. EPS-producing Firmicutes increased, enhancing EPS secretion, while filamentous Chloroflexi decreased, aligning with a reduced organic mineralization rate. Settlement and biological activity emerged as key factors affecting OM recovery, peaking at 43.97% with a 4-day SRT. The ratio of the sum of tryptophan-like and tyrosine-like components to fulvic-like components ((C1+C2)/C3) was proposed as a fluorescence indicator, serving as a hub to connect operational parameters, F/F regime, sludge status and process performance. When this ratio falls within the range of 1.04-1.36 during the stabilization phase, HiCS sludge achieves optimal status for OM capture with low aeration energy consumption.

Structure and molecular-level transformation for oxidation of effluent organic matters by manganese oxides

As important organic components in water environments, effluent organic matters (EfOMs) from wastewater treatment plants are widely present in Mn-rich environments or engineered treatment systems. The redox interaction between manganese oxides (MnOx) and EfOMs can lead to their structural changes, which are crucial for ensuring the safety of water environments. Herein, the reactivities of MnOx with EfOMs were evaluated, and it was found that MnOx with high specific surface area, active high-valent manganese content and lattice oxygen content (i.e., amorphous MnO2) possessed stronger oxidizing ability towards EfOMs. Accompanying by EfOMs oxidation, Mn(IV) and Mn(III) were reduced into Mn(II), with Mn(III) as the significant active species. Through molecular-level transformation analysis by ultrahigh mass spectrometry (FT-ICR MS), the highly reactive compounds in EfOMs were clearly determined to be that with more aromatic and unsaturated structures, especially lignin-like compounds (the highest content in EfOMs (over 60 %)). EfOMs were oxidized by amorphous MnO2 into products with lower humification index (0.60 vs. 0.46), smaller apparent molecular weight (386.94 Da vs. 368.68 Da), and higher biodegradability (BOD5/COD: 0.12 vs. 0.78). This finding suggested that redox reactions between MnOx and EfOMs might alter their abiotic and biotic behaviors in receiving water environments.

Transformation of sedimentary dissolved organic matter in electrokinetic remediation catalogued by FT-ICR mass spectrometry

In electrokinetic remediation (EKR), the sedimentary dissolved organic matter (DOM) could impede remediation by scavenging reactive species and generating unintended byproducts. Yet its transformation and mechanisms remained largely unknown. This study conducted molecular-level characterization of the water-extractable DOM (WEOM) in EKR using negative-ion electrospray ionization coupled to 21 tesla Fourier transform ion cyclotron resonance mass spectrometry (21 T FT-ICR MS). The results suggested that ∼55 % of the ∼7,000 WEOM compounds identified were reactive, and EKR lowered their diversity, molecular weight distribution, and double-bond equivalent (DBE) through a combination of electrochemical and microbial redox reactions. Heteroatom-containing WEOM (CHON and CHOS) were abundant (∼ 35% of the total WEOM), with CHOS generally being more reactive than CHON. Low electric potential (1 V/cm) promoted the growth of dealkylation and desulfurization bacteria, and led to anodic CO2 mineralization, anodic cleavage of -SO and -SO3, and cathodic cleavage of -SH2; high electric potential (2 V/cm) only enriched desulfurization bacteria, and differently, led to anodic oxygenation and cathodic hydrogenation of unsaturated and phenolic compounds, in addition to cathodic cleavage of -SH2. The long-term impact of these changes on soil quality and nitrogen-sulfur-carbon flux may be need to studied to identify unknown risks and new applications of EKR.

Molecular-level insight into the effect of fertilization regimes on the chemodiversity of dissolved organic matter in tropical cropland

Fertilization is a critical agronomic measure for croplands in tropical regions, owing to their low fertility. However, the effects of fertilization on the quantity and chemodiversity of latosolic dissolved organic matter (DOM) in tropical regions remain largely unknown. Therefore, in this study, the variations in latosol DOM concentrations and chemodiversity induced by inorganic fertilization and the co-application of inorganic fertilization with straw return, sheep manure, biochar, and vermicompost fertilizers at a molecular level were systematically investigated using multispectral techniques and ultrahigh-resolution mass spectrometry. In line with our expectations, the results showed that combined inorganic-organic fertilization improved soil quality by increasing soil organic carbon content compared to that under inorganic fertilization. However, as the most active and bioavailable organic carbon pool, dissolved organic carbonconcentrations between the fertilization treatments were not significantly different (p = 0.07). However, the dissolved organic carbon concentrations under combined inorganic-organic fertilization treatment (NPK plus straw return, 263.45 ± 37.51 mg/kg) were lower than those under inorganic fertilization treatment (282.10 ± 18.57 mg/kg). Spectral analysis showed that the DOM in the combined inorganic-organic fertilization treatments had a higher degree of humification and lower autogenetic contributions. Furthermore, Fourier transform ion cyclotron resonance mass spectrometry analysis indicated that the combined inorganic-organic fertilization increased the chemodiversity of latosolic DOM and promoted the production of large, oxidized, and stable molecules, including lignin, aromatic, and tannin compounds, which potentially benefits soil carbon sequestration in tropical regions. This study could provide a theoretical basis for elucidating on the potentially relevant ecological functions and environmental effects of DOM under fertilization regimes.

Microplastic-derived dissolved organic matter: Generation, characterization, and environmental behaviors

Microplastics (MPs) represent a substantial and emerging class of pollutants distributed widely in various environments, sparking growing concerns about their environmental impact. In environmental systems, dissolved organic matter (DOM) is crucial in shaping the physical, chemical, and biological processes of pollutants while significantly contributing to the global carbon budget. Recent findings have revealed that microplastic-derived dissolved organic matter (MP-DOM) constitutes approximately 10 % of the DOM present on the ocean surface, drawing considerable attention. Hence, this study's primary objective is to explore, the generation, characterization, and environmental behaviors of MP-DOM. The formation and characteristics of MP-DOM are profoundly influenced by leaching conditions and types of MPs. This review delves into the mechanisms of the generation of MP-DOM and provides an overview of a wide array of analytical techniques, including ultraviolet-visible (UV-Vis) spectroscopy, fluorescence spectroscopy, Fourier transform infrared spectroscopy (FTIR), and mass spectroscopy, used to assess the MP-DOM characteristics. Furthermore, this review investigates the environmental behaviors of MP-DOM, including its impacts on organisms, photochemical processes, the formation of disinfection by-products (DBPs), adsorption behavior, and its interaction with natural DOM. Finally, the review outlines research challenges, perspectives for future MP-DOM research, and the associated environmental implications.

High-Resolution Mass Spectrometry Combined with Reactive Oxygen Species Reveals Differences in Photoreactivity of Dissolved Organic Matter from Microplastic Sources in Aqueous Environments

Microplastics (MPs)-derived dissolved organic matter (MPs-DOM) is becoming a non-negligible source of DOM pools in aquatic systems, but there is limited understanding about the photoreactivity of different MPs-DOM. Herein, MPs-DOM from polystyrene (PS), polyethylene terephthalate (PET), poly(butylene adipate-co-terephthalate) (PBAT), PE, and polypropylene (PP), representing aromatic, biodegradable, and aliphatic plastics, were prepared to examine their photoreactivity. Spectral and high-resolution mass spectrometry analyses revealed that PS/PET/PBAT-DOM contained more unsaturated aromatic components, whereas PE/PP-DOM was richer in saturated aliphatic components. Photodegradation experiments observed that unsaturated aromatic molecules were prone to be degraded compared to saturated aliphatic molecules, leading to a higher degradation of PS/PET/PBAT-DOM than PE/PP-DOM. PS/PET/PBAT-DOM was mainly degraded by hydroxyl (•OH) via attacking unsaturated aromatic structures, whereas PE/PP-DOM by singlet oxygen (1O2) through oxidizing aliphatic side chains. The [•OH]ss was 1.21-1.60 × 10-4 M in PS/PET/PBAT-DOM and 0.97-1.14 × 10-4 M in PE/PP-DOM, while the [1O2]ss was 0.90-1.35 × 10-12 and 0.33-0.44 × 10-12 M, respectively. This contributes to the stronger photoreactivity of PS/PET/PBAT-DOM with a higher unsaturated aromatic degree than PE/PP-DOM. The photodegradation of MPs-DOM reflected a decreasing tendency from aromatic-unsaturated molecules to aliphatic-saturated molecules. Special attention should be paid to the photoreactivity and environmental impacts associated with MPs-DOM containing highly unsaturated aromatic compounds.

Novel insights into antimony mobilization in different high- antimony aquifers from the molecular signatures of dissolved organic matter

The crucial role of the fluorescent components of dissolved organic matter (DOM) in controlling antimony (Sb) mobilization in groundwater has been confirmed. However, the molecular signatures contributing to Sb enrichment in DOM remain unknown. This study aims to investigate the origins and molecular compositions of DOM in different high-Sb aquifers (Sb-mining and no-Sb-mining aquifer), as well as compare different molecular signatures of DOM and mechanisms for Sb migration. The findings showed that Sb concentrations in Sb-mining aquifer exhibited a positive correlation with lignin- and tannin-like molecules characterized by high O/C and low H/C ratios, indicating an increased abundance of aromatic components with higher Humification Index and SUV-absorbance at 254 nm, compared to no-Sb-mining aquifer. Correspondingly, the complexation and competitive adsorption were considered as the predominate formation mechanisms on Sb enrichment in Sb-mining aquifer. In addition, high abundances of bioreactivity DOM may facilitated the migration of Sb via electron transfer and competitive adsorption in native no-Sb-mining aquifer. The outcomes of this investigation offer novel insights into the mechanism on Sb enrichment influenced by DOM at the molecule level.

Electrochemical oxidation of reverse osmosis concentrate using a pilot-scale reactive electrochemical membrane filtration system: Performance and mechanisms

Scale-up treatment of real wastewater holds the key to promoting the practical application of electrochemical filtration technology. This work used a pilot-scale Ti/Pd reactive electrochemical membrane (REM) system (12 REM modules with a total REM area of 0.144 m2) to treat high-salinity reverse osmosis concentrate (ROC) from a chemical industry park. The pilot-scale Ti/Pd REM system demonstrated effective electrochemical degradation of ROC wastewater, achieving removal efficiencies of 82.3 ± 1.9% for COD and 46.7 ± 5.6% for TN at a membrane flux of 90 L/(m2·h) and a cell voltage of 5 V, with an energy consumption of 0.045 kWh/g-COD. Singlet oxygen (1O2) and reactive chlorine species were identified as the two primary reactive oxygen species generated in the Ti/Pd REM system. Fluorescence spectroscopy and Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR-MS) analysis indicated that the pilot-scale Ti/Pd REM treatment effectively oxidized humic acid-like substance and unsaturated aromatic compounds. Overall, the Ti/Pd REM technology shows a promising application potential for the treatment of high-salinity ROC from the chemical industry.

Chemical characteristics of dissolved organic matter in effluent from sludge alkaline fermentation liquid-fed sequencing batch reactors

Sludge alkaline fermentation liquid (SAFL) is a promising alternative to acetate for improving biological nitrogen removal (BNR) from wastewater. SAFL inevitably contains some refractory compounds, while the characteristics of dissolved organic matter (DOM) in effluent from SAFL-fed BNR process remain unclear. In this study, the molecular weight distribution, fluorescent composition and molecular profiles of DOM in effluent from SAFL and acetate-fed sequencing batch reactors (S-SBRs and A-SBRs, respectively) at different hydraulic retention time (12 h and 24 h) was comparatively investigated. Two carbon sources resulted in similar effluent TN, but a larger amount of DOM, which was bio-refractory or microorganisms-derived, was found in effluent of S-SBRs. Compared to acetate, SAFL increased the proportion of large molecular weight organics and humic-like substances in effluent DOM by 74.87%-101.3% and 37.52%-48.35%, respectively, suggesting their bio-refractory nature. Molecular profiles analysis revealed that effluent DOM of S-SBRs exhibited a more diverse composition and a higher proportion of lignin-like molecules. Microorganisms-derived molecules were found to be the dominant fraction (71.51%-72.70%) in effluent DOM (<800 Da) of S-SBRs. Additionally, a prolonged hydraulic retention time enriched Bacteroidota, Haliangium and unclassified_f_Comamonadaceae, which benefited the degradation of DOM in S-SBRs. The results help to develop strategies on reducing effluent DOM in SAFL-fed BNR process.

Deciphering fluorescent and molecular fingerprint of dissolved organic matter leached from microplastics in water

Despite extensive research into the presence and behavior of microplastics (MPs) in the environment, limited attention has been given to the investigation of the characteristics of dissolved organic matter (DOM) that leaches from MPs (MPs-DOM). Herein, two frequently encountered plastic particles in aquatic environments, specifically polyethylene terephthalate (PET)- and polyethylene (PE)-MPs, were subjected to leaching in the aquatic settings for seven days, both in the absence of light and under UV irradiation. Measurements of dissolved organic carbon (DOC) indicated that UV exposure enhanced the liberation of DOM from PET-MPs, while PE-MPs did not exhibit such leaching. After UV treatment for seven days, the DOM released from PET-MPs increased by 25 times, while that from PE-MPs remained almost unchanged. Then, the molecular diversity and the evolving formation of DOM originating from different MPs were comprehensively analyzed with fluorescence excitation-emission matrix (EEM) and Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR-MS). Specifically, both PET- and PE-DOM exhibited three fluorescence signatures, with the predominant C1 (tryptophan-like) component showing a decline in PET-DOM and a rise in PE-DOM during aging. The FT-ICR-MS analysis unveiled that PET-DOM grew more recalcitrant under UV exposure, while PE-DOM became increasingly labile. In brief, UV irradiation influences MPs-DOM release and transformation differently, depending on the plastic composition. This highlights the significance of exploring MPs-DOM transformation in securing environmental safety.

Enhanced electrochemical treatment of humic acids and metal ions in leachate concentrate: Experimental and molecular mechanism investigations

Membrane technologies are effective for treating leachate, but they generate leachate concentrates (LCs), which contain elevated humic acids (HAs) and metals. LCs are very challenging and expensive to treat; but in-situ coagulation-electrochemical oxidation (CO-EO) treatment is promising. We previously hypothesized and proved that substituting the widely used graphite cathode with an Al cathode will generate Al(OH)3 floccules that would enhance HAs removal in CO-EO systems. However, the fundamental mechanisms are unclear. Here, we examined this hypothesis using laboratory experiments (using an Al cathode and a Ti/Ti4O7 anode CO-EO system) and performed molecular dynamics (MD) simulation to investigate the underlying mechanisms. Up to 84.2% HAs was removed by the Al-cathode system, which is ∼10% higher than a graphite cathode-based system. Based on MD simulation we found that enhanced HAs removal occurred via two steps: (1) degradation by oxidants produced at the anode, and (2) subsequent coagulation with the Al(OH)3 generated from the Al cathode. This finding challenges the current belief that whole HAs and Al(OH)3 directly flocculate. Meanwhile, metal removal efficiency by the graphite cathode system was only 0.8-13.9%, which increased up to 13-folds at most when in the Al cathode system. This work provides new molecular-level insights into an efficient electrochemical treatment of LC.

Nitroaromatic Compounds from Secondary Nitrate Formation and Biomass Burning Are Major Proinflammatory Components in Organic Aerosols in Guangzhou: A Bioassay Combining High-Resolution Mass Spectrometry Analysis

The limited characterization and detection capacity of unknown compounds hinder our understanding of the molecular composition of toxic compounds in PM2.5. The present study applied Fourier transform ion cyclotron resonance mass spectrometry coupled with negative and positive electrospray ionization sources (ESI-/ESI+ FT-ICR-MS) to probe the molecular characteristics and dynamic formation processes of the effective proinflammatory components in organic aerosols (OAs) of PM2.5 in Guangzhou for one year. We detected abundant proinflammatory molecules in OAs, mainly classified as CHON compounds (compounds composed of C, H, O, and N atoms) in elemental and nitroaromatic compounds (NACs) in structures. From the perspective of the formation process, we discovered that these proinflammatory molecules, especially toxic NACs, were largely driven by secondary nitrate formation and biomass burning (in emission source), as well as SO2 (in atmospheric evolution). In addition, our results indicated that the secondary processes had replaced the primary emission as the main contributing source of the toxic proinflammatory compounds in OAs. This study highlights the importance of community measures to control the production of nitroaromatic compounds derived from secondary nitrate formation and biomass burning in urban areas.

Effect of mixing intensity on volatile fatty acids production in sludge alkaline fermentation: Insights from dissolved organic matter characteristics and functional microorganisms

Alkaline fermentation for volatile fatty acids (VFAs) production has shown potential as a viable approach to treat sewage sludge. The hydrolysis and acidogenesis of sludge are greatly influenced by mixing. However, the effects of mixing intensity on VFAs production in sludge alkaline fermentation (SAF) remain poorly understood. This study investigated the impacts of mixing intensity (30, 90 and 150 rpm continuous mixing, and 150 rpm intermittent mixing) on VFAs production, dissolved organic matter (DOM) characteristics, phospholipid fatty acid profiles and microbial population distribution in SAF. Results showed that 150 rpm continuous and intermittent mixing enhanced the hydrolysis of sludge, while 150 rpm intermittent mixing resulted in the highest VFAs production (3886 ± 266.1 mg COD/L). Analysis of fluorescent and molecular characteristics of DOM revealed that 150 rpm intermittent mixing facilitated the conversion of released DOM, especially proteins-like substances, into VFAs. The abundance of unsaturated and branched fatty acids of microbes increased under 150 rpm intermittent mixing, which could aid in DOM degradation and VFAs production. Firmicutes and Tissierella were enriched at 150 rpm intermittent mixing, which favored the maximum VFAs yield. Moreover, Firmicutes were found to be the key functional microorganisms influencing the yield of VFAs during SAF. This study provides an understanding about the mixing intensity effects on VFAs production during SAF, which could be helpful to improve the yield of VFAs.

Molecular insights into the dissolved organic matter of leather wastewater in leather industrial park wastewater treatment plant

Leather wastewater (LW) effluent is characterized by complex organic matter, high salinity, and poor biodegradability. To meet the discharge standards, LW effluent is often mixed with municipal wastewater (MW) before being treated at a leather industrial park wastewater treatment plant (LIPWWTP). However, whether this method efficiently removes the dissolved organic matter (DOM) from LW effluent (LWDOM) remains debatable. In this study, the transformation of DOM during full-scale treatment was revealed using spectroscopy and Fourier transform ion cyclotron resonance mass spectrometry. LWDOM exhibited higher aromaticity and lower molecular weight than DOM in MW (MWDOM). The DOM properties in mixed wastewater (MixW) were similar to those in LWDOM and MWDOM. The MixW was treated using a flocculation/primary sedimentation tank (FL₁/PST), anoxic/oxic (A/O) process, secondary sedimentation tank (SST), flocculation/sedimentation tank, denitrification filter (FL₂/ST-DNF), and an ozonation contact reactor (O₃). The FL₁/PST unit preferentially removed the peptide-like compounds. The A/O-SST units had the highest removal efficiencies for dissolved organic carbon (DOC) (61.34 %) and soluble chemical oxygen demand (SCOD) (52.2 %). The FL₂/ST-DNF treatment removed the lignin-like compounds. The final treatment showed poor DOM mineralization efficiency. The correlation between water quality indices, spectral indices, and molecular-level parameters indicated that lignin-like compounds were strongly correlated with spectral indices and CHOS compounds considerably contributed to the SCOD and DOC. Although the effluent SCOD met the discharge standard, some refractory DOM from LW remained in the effluent. This study illustrates the composition and transformation of DOM and provides theoretical guidance for improving the current treatment processes.

The transformation of dissolved organic matter and formation of halogenated by-products during electrochemical advanced oxidation pretreatment for shale gas produced water

Electrochemical advanced oxidation processes (EAOPs) have shown great potential for the treatment of shale gas produced water (SGPW). In this study, we investigated the transformation of dissolved organic matter (DOM) during EAOPs of SGPW and the formation of toxic halogenated by-products at various current densities, using fluorescence spectroscopy and Fourier transform ion cyclotron resonance mass spectrometry. We found that the priority of DOM removal was terrestrial humic-like > microbial humic-like > protein-like substances. Non-Halogenated organic compounds (non-HOCs) and HOCs were predominantly CHO, and CHOCl/CHOBr compounds in EAOP-treated SGPW, respectively. As applied current density and treatment time increased, the production of oxyhalides increased, with chlorate > bromate > perchlorate. Meanwhile, most DOM was mineralized, resulting in residual products with higher modified aromaticity index (AI_mod) and nominal oxidation state of carbon (NOSC). The resistants had lower mass-to-charge ratio (m/z), AI_mod, NOSC, and double bond equivalent minus oxygen per carbon ((DBE-O)/C). The dominant reactions were the addition of tri-oxygen and deallyl. Bromine addition dominated the reactions of halogenating addition, while chlorine addition took second place. Furthermore, the acute toxicity of SGPW was positively correlated with inorganic halogenated by-products. This study contributes to the understanding and improvement of EAOPs for the treatment of SGPW.

Three-dimensional structured electrode for electrocatalytic organic wastewater purification: Design, mechanism and role

Considering the growing need in decentralized water treatment, the application of electrocatalytic processes (EP) to achieve organic wastewater purification will be dominant in the near future due to high efficiency, small reactor assembly as well as the flexibility of operation and management. The catalytic performance of electrode materials determines the development of this technology. Among them, the unique three-dimensional (3D) structure electrode shows better performance than two-dimensional (2D) electrode in increasing mass transfer, enhancing adsorption and exposing more active sites. Hence, this review starts with the introduction of definition, classification, advantages and disadvantages of 3D electrode materials. Then a critical discussion on the design and construction of 3D electrode materials for organic wastewater purification application is provided. Next, the removal mechanism of organic pollutants on the surface of 3D electrode, the role of 3D structure, the design of reactor with 3D electrode, the conversion and toxicity of degradation products, electrode energy efficiency, stability and cost, are comprehensively reviewed. At last, current challenges and future perspectives for the development of 3D electrode materials are addressed. We deem that this review will provide a valuable insight into the design and application of 3D electrodes in environmental water purification.

Evaluating UV254 absorbance reductions in landfill leachate for municipal sewage co-treatment through timed UV/electrooxidation

Landfill leachate contains dissolved organic matter (DOM) exhibiting high ultraviolet absorbance at 254 nm (UVA₂₅₄). The UVA₂₅₄ limits leachate co-treatment with municipal sewage by hindering the downstream UV disinfection efficiency at wastewater treatment plants. Here, we alleviated the UVA₂₅₄ by timing the radiation in a UV/electrooxidation (UV/EO) process to accelerate reactive species formation. At 200 A·m^-2, the UV radiation was delayed by 10 min to accumulate 21 mg·L^-1 as Cl₂, which enhanced the initial radical formation rate by 5.25 times compared with a simultaneous UV/EO. The timed operation increased the steady-state concentrations of ClO^• by 700 times to 4.11 × 10^-14 M and reduced the leachate UVA₂₅₄ by 78.2% after 60 min. We identified that aromatic formulas with low oxygen content were susceptible to UV/EO from Fourier-transform ion cyclotron resonance mass spectrometry analysis. The toxicity of the treated leachate and generated byproducts was assessed through specific oxygen uptake rates (SOUR) and developmental assays with Platynereis dumerilii. After quenching the residual chlorine, leachate co-treatment at 3.5% v/v presented minimal toxicological risk. Our findings provide operational insights for applying UV/EO in high UVA₂₅₄ matrices such as landfill leachate.

Molecular-level transformation of refractory organic matter during flocculation-ultraviolet/peroxymonosulfate treatment of MBR-treated landfill leachate

Refractory organic matter in membrane bioreactor effluent resulting from landfill leachate treatment has a complex composition. This paper identified the transformation mechanism of organic matter in a flocculation-ultraviolet (UV)/peroxymonosulfate (PMS) system at the molecular level using electrospray ionization coupled with Fourier transform ion cyclotron resonance mass spectrometry. The results showed that the flocculation system was able to remove a large amount of dissolved organic matter (DOM) with high oxidation and unsaturation/saturation. UV radiation displayed a relatively strong reactivity for DOM with an electron-rich structure, which it can transform into DOM with lower aromaticity through photolysis and photosensitivity, although the effectiveness of the transformation was poor. In comparison, due to the action of reactive oxygen species, the UV/PMS system can enable reactions such as demethylation, dehydrogenation, decarboxylation, dehydroxylation, ring cleavage, and decarbonylation. It can remove approximately 60% quantity of the total DOM and produce DOM featuring a higher degree of oxidation and saturation than that of the UV system alone. The results showed that the UV/PMS system was a complementary of flocculation in DOM removal from the membrane bioreactor effluent, while the system also resulted in a large number of sulfuric compounds; thus, requiring further evaluation of its ecological effects.

Molecular-level characterization of natural organic matter in the reactive electrochemical ceramic membrane system for drinking water treatment using FT-ICR MS

Applications of electrochemical advanced oxidation processes are rising in drinking water treatment for effective mitigation of refractory organic compounds. This study explored the fate of natural organic matter (NOM) (lake water and standard NOM (SRNOM solution)) at molecular-level in the reactive electrochemical membrane (REM) system utilizing Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS). Fluorescence spectroscopy showed above 90 % removal of the humic-like component in both lake water and SRNOM solution in 10 min of REM operation compared to 70-80 % removal of the fulvic-like component after 30 min. REM-based treatment effectively eliminated (>70 %) the disinfection byproduct precursors. The lake water, sharing ~70 % of similar compounds with SRNOM, displayed a different propensity toward electrochemical oxidation, and its finished water was characterized with relatively lower double-bond equivalent (DBE), nominal oxidation state of carbon (NOSC), and aromaticity compared to that of SRNOM. The chloride ions in the water matrix of lake water impacted the electrochemical oxidation and generated significantly different transformation products than SRNOM solution. The heteroatoms (N and S) containing compounds (CHON and CHOS) were preferentially degraded in lake water; however, CHOS compounds were removed fewer in SRNOM. The electrosorption and electrochemical oxidation on the REM surface were the significant contributors for NOM removal. The newly formed compounds were mostly retained on the REM surface and fewer were released in finished water. This study is believed to help understand the fate of NOM in real source drinking water during electrochemical treatment.

Molecular transformations of dissolved organic matter during UV/O3-assisted membrane filtration of UASB-treated real textile wastewater

A ceramic membrane reactor (CMR) integrated with in-situ UV/O₃ was assessed for post-treatment of the effluent out of an up-flow anaerobic sludge blanket (UASB) reactor treating real textile wastewater, focusing on the transformation of dissolved organic matter (DOM). Fourier transform ion cyclotron resonance mass spectrometry (FTICR-MS) revealed the transformation of heteroatomic DOM containing S, N or both to simpler DOM containing mainly C, H, and O atoms. The decreased N contents in products (N/C = 0.0249) compared to precursors (N/C = 0.0311) and the higher O/C ratios in the N-containing products suggest the removal of R-NH₂ groups accompanying DOM oxidation. While, S-containing compounds in the products had lower O/C and H/C ratios, suggesting a reduced state and the transformation of R-SO₃ to R-S-R. H-abstraction and OH addition were identified as the primary oxidation mechanisms, thus enhancing the dominance of highly unsaturated and phenolic DOM in the effluent (70.3%) compared to the feed (56.6%). The double bond equivalent (DBE) was also increased by 26% in the effluent compared to the feed and by 33% in products compared to precursors. These findings help understand the DOM transformation in UV/O₃-assisted ceramic membrane reactors and call for comprehensive toxicity analyses of effluents from the advanced oxidation processes.

Using Potential Molecular Transformation To Understand the Molecular Trade-Offs in Soil Dissolved Organic Matter

Understanding the chemical composition and molecular transformation in soil dissolved organic matter (DOM) is important to the global carbon cycle. To address this issue, ultrahigh-resolution Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR-MS) was applied to investigate DOM molecules in 36 paddy soils collected from subtropical China. All the detected 7576 unique molecules were divided into seven compound groups, and nine trade-off relationships between different compound groups were revealed based on principal component analysis and Pearson's correlation. An optimized method was developed to evaluate all potential molecular transformations in DOM samples. The concept of thermodynamics was introduced to evaluate the identified molecular transformations and classify them as thermodynamically favorable (TFP) and thermodynamically limited (TLP) processes. Here, we first tried to understand the molecular trade-offs by using the potential molecular transformations. All the nine trade-offs could be explained by molecular transformations. Six trade-offs had bases of biochemical reactions, and the trade-off-related direct transformations could explain the content variations of carbohydrate-like, condensed aromatic-like, tannin-like, and lignin-like compounds in TLP. More reasonable explanations existed in the TLP rather than TFP, which demonstrated the critical role of external energy in the molecular transformation of soil DOM.

Unraveling dissolved organic matter in drinking water through integrated ozonation/ceramic membrane and biological activated carbon process using FT-ICR MS

The performance of an integrated process comprising coagulation, ozonation, and catalytic ceramic membrane filtration (CMF) followed by treatment with biological active carbon (BAC) was evaluated in a pilot-scale (96 m³/d) experiment to understand the biostability and quality of the finished water. The fate of dissolved organic matter (DOM) at the molecular level was explored using Fourier-transform ion cyclotron resonance mass spectrometry (FT-ICR MS). Biostable finished water with an assimilable organic carbon (AOC) concentration of 30.2-45.4 µg/L was obtained by the integrated process, and the high hydraulic retention time (HRT) (≥ 45 min) of the BAC filter was necessary to provide biostable finished water. The coagulation/O₃/CMF unit efficiently transformed nitrogen-containing polyaromatic hydrocarbons (PAH) with aromaticity and large molecular weight (Mw) (500-1000 Da) into CHO-type highly unsaturated phenolic compounds (HuPh) with less aromaticity and medium Mw (300-500 Da), which were effectively removed by subsequent BAC filtering. The main reaction was oxygen addition, followed by deamination and dealkylation of the coagulation/O₃/CMF unit and decarboxylation of the BAC filter. Principal component analysis revealed that N-containing and large-Mw PAH are potential AOC precursors, and the chemical characteristics of CHO-type and medium-Mw HuPh make them AOC candidates (correlation coefficients > 0.96). This study provides insights into the management of drinking water biostability and its suitability for the practical application of the integrated coagulation/O₃/CMF-BAC process in drinking water treatment plants.