Growth of organic films on indoor surfaces

Reactive oxygen species on indoor surfaces

Reactive oxygen species (ROS) are relatively unstable oxygen-containing radicals or non-radicals, some of which may react with tissues and biomolecules after entering the body. ROS is present in indoor aerosols, but it is unclear how much of that ROS is of indoor origin. Indoor surface films have been hypothesized to be a major source of the ROS observed on indoor aerosols. In this study, the ROS concentration on residential indoor surfaces was measured using a xylenol orange ferrous oxidation assay after wiping and extraction. On genuine surfaces frequently touched by apartment occupants, the concentration was >0.2 nmol cm-2; infrequently touched surfaces were at or below detection limits. On clean glass plates that had been deployed in apartments for 6 weeks, horizontal plates had higher concentrations than vertically oriented plates. The highest concentration, 1.3 nmol cm-2, was observed on a horizontally oriented plate close to an electric stove. To simulate the dynamic oxidation of unsaturated hydrocarbons on indoor surfaces, a surface lipid mixture (SLM) was dosed on 19 glass plates which were then exposed to untreated laboratory air for periods ranging from 1 to 56 days. During the first 5-6 days, the ROS concentration increased roughly linearly to a maximum of 5-6 nmol cm-2. Then the concentration ceased to increase, perhaps because reactive sites had become depleted. After 2 weeks, ROS decreased slowly, possibly due to a combination of volatilization, decomposition and continued formation by autoxidation. These field and laboratory results support the hypothesis that indoor surfaces can be a source of ROS.

Ozone Chemistry on Greasy Glass Surfaces Affects the Levels of Volatile Organic Compounds in Indoor Environments

The chemistry of ozone (O3) on indoor surfaces leads to secondary pollution, aggravating the air quality in indoor environments. Here, we assess the heterogeneous chemistry of gaseous O3 with glass plates after being 1 month in two different kitchens where Chinese and Western styles of cooking were applied, respectively. The uptake coefficients of O3 on the authentic glass plates were measured in the dark and under UV light irradiation typical for indoor environments (320 nm < λ < 400 nm) at different relative humidities. The gas-phase product compounds formed upon reactions of O3 with the glass plates were evaluated in real time by a proton-transfer-reaction quadrupole-interface time-of-flight mass spectrometer. We observed typical aldehydes formed by the O3 reactions with the unsaturated fatty acid constituents of cooking oils. The formation of decanal, 6-methyl-5-hepten-2-one (6-MHO), and 4-oxopentanal (4-OPA) was also observed. The employed dynamic mass balance model shows that the estimated mixing ratios of hexanal, octanal, nonanal, decanal, undecanal, 6-MHO, and 4-OPA due to O3 chemistry with authentic grime-coated kitchen glass surfaces are higher in the kitchen where Chinese food was cooked compared to that where Western food was cooked. These results show that O3 chemistry on greasy glass surfaces leads to enhanced VOC levels in indoor environments.

When Does Multiphase Chemistry Influence Indoor Chemical Fate?

Human chemical exposure often occurs indoors, where large variability in contaminant concentrations and indoor chemical dynamics make assessments of these exposures challenging. A major source of uncertainty lies in the rates of chemical transformations which, due to high surface-to-volume ratios and rapid air change rates relative to rates of gas-phase reactions indoors, are largely gas-surface multiphase processes. It remains unclear how important such chemistry is in controlling indoor chemical lifetimes and, therefore, human exposure to both parent compounds and transformation products. We present a multimedia steady-state fugacity-based model to assess the importance of multiphase chemistry relative to cleaning and mass transfer losses, examine how the physicochemical properties of compounds and features of the indoor environment affect these processes, and investigate uncertainties pertaining to indoor multiphase chemistry and chemical lifetimes. We find that multiphase reactions can play an important role in chemical fate indoors for reactive compounds with low volatility, i.e., octanol-air equilibrium partitioning ratios (Koa) above 108, with the impact of this chemistry dependent on chemical identity, oxidant type and concentration, and other parameters. This work highlights the need for further research into indoor chemical dynamics and multiphase chemistry to constrain human exposure to chemicals in the built environment.

Indoor air levels of polycyclic aromatic compounds (PAC) in public buildings with creosote impregnated constructions - A pilot case study using passive samplers

Creosote has been used in Sweden as a wood preservative in buildings since the 19th century. These buildings can function as workplaces, homes, and cultural buildings to which the public has access. Creosote contains polycyclic aromatic hydrocarbons (PAH) which are well known carcinogens. To understand exposure and risks in an indoor environment, it is important to determine air levels of parent PAHs as well as the more toxic nitrated and oxygenated PAH derivatives (NPAH, OPAH). This study aims to investigate indoor air levels of polycyclic aromatic compounds (PACs) e.g., PAH, NPAH, OPAH and dibenzothiophenes in buildings containing creosote sources and whether these levels pose a health risk. Four cultural buildings were studied, all located within a radius of 130 m. Two were known to have creosote sources, and two had not. Polyurethane foam passive air samplers (PUF-PAS) were used to indicate possible point sources. PUF-PAS measurements were performed for one month in each building winter and summer. Simultaneously, PAC outdoor level measurements were performed. Buildings with creosote impregnated constructions had notably higher indoor air levels of PAC (31-1200 ng m-3) compared to the two buildings without creosote sources (14-45 ng m-3). The PAH cancer potency (sum of benzo[a]pyrene equivalents (BaPeq)) was more than one order of magnitude higher in the buildings containing creosote impregnated wood compared to reference buildings. The highest value was 5.1 BaPeq ng m-3 which was significantly higher than the outdoor winter measurement (1.3 BaPeq ng m-3). Fluoranthene and phenanthrene, with significant distribution in gas phase, but also several particulate NPAHs contributed significantly to the total cancer risk. Thus, creosote containing buildings can still contaminate the indoor air with PACs despite being over a hundred years old. The PUF-PAS was shown to be a good tool providing quantitative/semiquantitative measures of PACs exposure in indoor microenvironments.

Multiphase Ozonolysis of Bisphenol A: Chemical Transformations on Surfaces in the Environment

High global plastic production volumes have led to the widespread presence of bisphenol compounds in human living and working environments. The most common bisphenol, bisphenol A (BPA), despite being endocrine disruptive and estrogenic, is still not fully banned worldwide, leading to continued human exposure via particles in air, dust, and surfaces in both outdoor and indoor environments. While its abundance is well documented, few studies have addressed the chemical transformations of BPA, the properties of its reactive products, and their toxicity. Here, the first gas-surface multiphase ozonolysis experiment of BPA thin films, at a constant ozone mixing ratio of 100 ppb, was performed in a flow tube for periods up to 24 h. Three transformation products involving the addition of 1, 2, and 3 oxygen atoms to the molecule were identified by LC-ESI-HRMS analyses. Exposure of indoor air to thin BPA surface films and BPA-containing thermal paper over periods of days validated the flow tube experiments, demonstrating the rapid nature of this multiphase ozonolysis reaction at atmospherically relevant ozone levels. Multiple transformation pathways are proposed that are likely applicable to not only BPA but also emerging commercial bisphenol products.

Composition of indoor organic surface films in residences: simulating the influence of sources, partitioning, particle deposition, and air exchange

Indoor surfaces are coated with organic films that modulate thermodynamic interactions between the surfaces and room air. Recently published models can simulate film formation and growth via gas-surface partitioning, but none have statistically investigated film composition. The Indoor Model of Aerosols, Gases, Emissions, and Surfaces (IMAGES) was used here to simulate ten years of nonreactive film growth upon impervious indoor surfaces within a Monte Carlo procedure representing a sub-set of North American residential buildings. Film composition was resolved into categories reflecting indoor aerosol (gas + particle phases) factors from three sources: outdoor-originating, indoor-emitted, and indoor-generated secondary organic material. In addition to gas-to-film partitioning, particle deposition was modeled as a vector for organics to enter films, and it was responsible for a majority of the film mass after ∼1000 days of growth for the median simulation and is likely the main source of LVOCs within films. Therefore, the organic aerosol factor possessing the most SVOCs contributes most strongly to the composition of early films, but as the film ages, films become more dominated by the factor with the highest particle concentration. Indoor-emitted organics (e.g. from cooking) often constituted at least a plurality of the simulated mass in developed films, but indoor environments are diverse enough that any major organic material source could be the majority contributor to film mass, depending on building characteristics and indoor activities. A sensitivity analysis suggests that rapid film growth is most likely in both newer, more air-tight homes and older homes near primary pollution sources.

Formation kinetics of SVOC organic films and their impact on child exposure in indoor environments

We conducted an SVOC mass transfer and child-exposure modeling analysis considering the combined sorption of multiple SVOCs containing DnBP, BBP, DEHP, DINP and DINCH in indoor environments. A mechanistic model was applied to describe the organic film formation, and a partition-coefficient-prediction model was originally developed for the realistic organic films. The characteristics of film formation on impermeable surfaces were examined based on three different assumptions: the widely-used constant Kns,im assumption, Koa assumption, and the proposed Kom assumption (predicted specifically for the realistic organic films in this study). After long-term SVOC sorption, the organic film reached increasing equilibrium gradually under constant Kns,im assumption. While under Koa and Kom assumption, organic films exhibited nearly linear increases on surfaces, the trends of which agreed well with field studies. However, the film thicknesses calculated under Kom assumption with larger film partition coefficients were approximately twice larger than those under Koa assumption. Meanwhile, Horizontal surfaces with higher deposition rates of particle-phase SVOCs exhibited larger velocities of film growth compared to vertical surfaces. Under the Kom assumption, exposures of hazardous SVOCs for a 3-year-old child increased by 87.5 %-198.7 % even with the weekly cleaning of indoor impermeable surfaces, carpet and cloth. This study is anticipated to provide valuable insights into the film-forming characteristics of multiple SVOCs and the accompanying significant health risks to human beings in indoor environments.

The legalization of cannabis may result in increased indoor exposure to Δ9-tetrahydrocannabinol

Cannabis is a genus of plants in the Cannabaceae family that contains tetrahydrocannabinolic acid. When heated or burned, the acid decarboxylates to form tetrahydrocannabinol (THC). Its (-)-trans-Δ9-THC isomer is a psychoactive substance that has been used as a drug for centuries. In most countries, both the private sale of cannabis products and their use for non-medical purposes are still prohibited by law. However, for some time now there has been societal and political pressure to at least partially legalize cannabis products. It can be expected that such a measure will lead to a significant increase in the consumption of cannabis. However, this also increases the possibility of involuntary passive exposure to THC and contamination of the indoor environment. In indoor sciences, THC is still a largely unknown or underrepresented substance. In this perspective paper, THC will therefore first be presented on the basis of its physical properties. Then, the distribution of THC in different indoor compartments and potential routes of passive exposure are discussed. Finally, an assessment of the future importance of THC for indoor use is made. Previous experience has shown that early monitoring is always advantageous so that preventive and protective measures can be taken quickly if necessary.

Dust phase and window film phase phthalates in dormitories: profile characteristics, source screening, and estimated gas-phase concentration and dermal exposure comparison

Recently, phthalate exposure has become a major public health concern. However, gaps still remain in our understanding of phthalate profile characteristics, source screening, and gas-phase estimation. This study measured phthalate concentrations in dust and window films in 101 dormitories at 13 universities in Beijing, China, from October to December 2019. Based on the phthalate concentrations in the dust and window films, we estimated the gas-phase phthalate concentrations using steady-state and instantaneous equilibrium models, respectively, and male and female students' dermal exposure using the Monte Carlo simulation. Commonly used materials and supplies were screened for phthalate sources and evaluated using the positive matrix factorization (PMF) model. The results showed that the detection frequency of ten phthalates ranged from 79.2 to 100% in dust and from 84.2 to 100% in window films. Dicyclohexyl phthalate (DCHP), di-(2-ethylhexyl) phthalate (DEHP), and dibutyl phthalate (DBP) were the most abundant phthalates in both indoor media and were also predominant in the indoor materials and supplies. The PMF results indicated that the potential sources of phthalates in dust and window films had both similarities and differences. Indoor door seals, paint, coatings, cables, air-conditioning rubber cable ties, wallpaper, and window seals were highly probable sources of phthalates. The gas-phase phthalate concentrations estimated using the two methods differed, especially for phthalates with high octanol-air partition coefficients (Koa), varying by 1-2 orders of magnitude. Moreover, compared with related studies, the gas-phase concentrations were significantly underestimated for phthalates with high Koa values, while the estimated gas-phase concentrations of phthalates with low Koa values were closer to the measured values. The estimated dermal exposure using the two methodologies also considerably differed. Such findings suggest that more attention should be focused on the exposure risk from the dust phase and window film phase phthalates.

Gas-Phase and Surface-Initiated Reactions of Household Bleach and Terpene-Containing Cleaning Products Yield Chlorination and Oxidation Products Adsorbed onto Indoor Relevant Surfaces

The use of household bleach cleaning products results in emissions of highly oxidative gaseous species, such as hypochlorous acid (HOCl) and chlorine (Cl2). These species readily react with volatile organic compounds (VOCs), such as limonene, one of the most abundant compounds found in indoor enviroments. In this study, reactions of HOCl/Cl2 with limonene in the gas phase and on indoor relevant surfaces were investigated. Using an environmental Teflon chamber, we show that silica (SiO2), a proxy for window glass, and rutile (TiO2), a component of paint and self-cleaning surfaces, act as a reservoir for adsorption of gas-phase products formed between HOCl/Cl2 and limonene. Furthermore, high-resolution mass spectrometry (HRMS) shows that the gas-phase reaction products of HOCl/Cl2 and limonene readily adsorb on both SiO2 and TiO2. Surface-mediated reactions can also occur, leading to the formation of new chlorine- and oxygen-containing products. Transmission Fourier-transform infrared (FTIR) spectroscopy of adsorption and desorption of bleach and terpene oxidation products indicates that these chlorine- and oxygen-containing products strongly adsorb on both SiO2 and TiO2 surfaces for days, providing potential sources of human exposure and sinks for additional heterogeneous reactions.

Model Framework for Predicting Semivolatile Organic Material Emissions Indoors from Organic Aerosol Measurements: Applications to HOMEChem Stir-Frying

Cooking activities emit myriad low-volatility, semivolatile, and highly volatile organic compounds that together form particles that can accumulate to large indoor concentrations. Absorptive partitioning thermodynamics governs the particle-phase organic aerosol concentration mainly via temperature and sorbing mass impacts. Cooking activities can increase the organic sorbing mass by 1-2 orders of magnitude, increasing particle-phase concentrations and affecting emission rate calculations. Although recent studies have begun to probe the volatility characteristics of indoor cooking particles, parametrizations of cooking particle mass emissions have largely neglected these thermodynamic considerations. Here, we present an improved thermodynamics-based model framework for estimating condensable organic material emission rates from a time series of observed concentrations, given that adequate measurements or assumptions can be made about the volatility of the emitted species. We demonstrate the performance of this methodology by applying data from stir-frying experiments performed during the House Observations of Microbial and Environmental Chemistry (HOMEChem) campaign to a two-zone box model representing the UTest House. Preliminary estimates of organic mass emitted on a per-stir-fry basis for three types of organic aerosol factors are presented. Our analysis highlights that using traditional nonvolatile particle models and emission characterizations for some organic aerosol emitting activities can incorrectly attribute concentration changes to emissions rather than thermodynamic effects.

Chemical Fate of Oils on Indoor Surfaces: Ozonolysis and Peroxidation

Unsaturated triglycerides found in food and skin oils are reactive in ambient air. However, the chemical fate of such compounds has not been well characterized in genuine indoor environments. Here, we monitored the aging of oil coatings on glass surfaces over a range of environmental conditions, using mass spectrometry, nuclear magnetic resonance (NMR), and electron paramagnetic resonance (EPR) techniques. Upon room air exposure (up to 17 ppb ozone), the characteristic ozonolysis products, secondary ozonides, were observed on surfaces near the cooking area of a commercial kitchen, along with condensed-phase aldehydes. In an office setting, ozonolysis is also the dominant degradation pathway for oil films exposed to air. However, for indoor enclosed spaces such as drawers, the depleted air flow makes lipid autoxidation more favorable after an induction period of a few days. Forming hydroperoxides as the major primary products, this radical-mediated peroxidation behavior is accelerated by indoor direct sunlight, but the initiation step in dark settings is still unclear. These results are in accord with radical measurements, indicating that indoor photooxidation facilitates radical formation on surfaces. Overall, many intermediate and end products observed are reactive oxygen species (ROS) that may induce oxidative stress in human bodies. Given that these species can be widely found on both food and household surfaces, their toxicological properties are worth further attention.

The persistence of smoke VOCs indoors: Partitioning, surface cleaning, and air cleaning in a smoke-contaminated house

Wildfires are increasing in frequency, raising concerns that smoke can permeate indoor environments and expose people to chemical air contaminants. To study smoke transformations in indoor environments and evaluate mitigation strategies, we added smoke to a test house. Many volatile organic compounds (VOCs) persisted days following the smoke injection, providing a longer-term exposure pathway for humans. Two time scales control smoke VOC partitioning: a faster one (1.0 to 5.2 hours) that describes the time to reach equilibrium between adsorption and desorption processes and a slower one (4.8 to 21.2 hours) that describes the time for indoor ventilation to overtake adsorption-desorption equilibria in controlling the air concentration. These rates imply that vapor pressure controls partitioning behavior and that house ventilation plays a minor role in removing smoke VOCs. However, surface cleaning activities (vacuuming, mopping, and dusting) physically removed surface reservoirs and thus reduced indoor smoke VOC concentrations more effectively than portable air cleaners and more persistently than window opening.

Effective mass accommodation for partitioning of organic compounds into surface films with different viscosities

Indoor surfaces can act as reservoirs and reaction media influencing the concentrations and type of species that people are exposed to indoors. Mass accommodation and partitioning are impacted by the phase state and viscosity of indoor surface films. We developed the kinetic multi-layer model KM-FILM to simulate organic film formation and growth, but it is computationally expensive to couple such comprehensive models with indoor air box models. Recently, a novel effective mass accommodation coefficient (αeff) was introduced for efficient and effective treatments of gas-particle partitioning. In this study, we extended this approach to a film geometry with αeff as a function of penetration depth into the film, partitioning coefficient, bulk diffusivity, and condensed-phase reaction rate constant. Comparisons between KM-FILM and the αeff method show excellent agreement under most conditions, but with deviations before the establishment of quasi-equilibrium within the penetration depth. We found that the deposition velocity of species and overall film growth are impacted by bulk diffusivity in highly viscous films (Db ∼<10-15 cm2 s-1). Reactions that lead to non-volatile products can increase film thicknesses significantly, with the extent of film growth being dependent on the gas-phase concentration, rate coefficient, partitioning coefficient and diffusivity. Amorphous semisolid films with Db > ∼10-17-10-19 cm2 s-1 can be efficient SVOC reservoirs for compounds with higher partitioning coefficients as they can be released back to the gas phase over extended periods of time, while glassy solid films would not be able to act as reservoirs as gas-film partitioning is impeded.

Ozone Loss: A Surrogate for the Indoor Concentration of Ozone-Derived Products

Ozone concentrations tend to be substantially lower indoors than outdoors, largely because of ozone reactions with indoor surfaces. When there are no indoor sources of ozone, a common condition, the net concentration of gaseous products derived from indoor ozone chemistry scales linearly with the difference between outdoor and indoor ozone concentrations, termed "ozone loss." As such, ozone loss is a metric that might be used by epidemiologists to disentangle the adverse health effects of ozone's oxidation products from those of exposure to ozone itself. The present paper examines the characteristics, potential utility, and limitations of the ozone loss concept. We show that for commonly occurring indoor conditions, the ozone loss concentration is directly proportional to the total rate constant for ozone removal on surfaces (ksum) and inversely proportional to the net removal of ozone by air exchange (λ) plus surface reactions (ksum). It follows that the ratio of indoor ozone to ozone loss is equal to the ratio of λ to ksum. Ozone loss is a promising metric for probing potential adverse health effects resulting from exposures to products of indoor ozone chemistry. Notwithstanding its virtues, practitioners using it should be mindful of the limitations discussed in this paper.

Cerium-modified amorphous manganese oxides for efficient catalytic removal of ozone

Manganese-based catalysts were widely developed for catalytic removal of ozone, and the low stability and water inactivation are major challenges. To improve removal performance of ozone, three methods were applied to modify amorphous manganese oxides, including acidification, calcination and Ce modification. The physiochemical properties of prepared samples were characterized, and the catalytic activity for ozone removal was evaluated. All modification methods can promote the removal of ozone by amorphous manganese oxides, and Ce modification showed the most significant enhancement. It was confirmed that the introduction of Ce markedly changed the amount and property of oxygen vacancies in amorphous manganese oxides. Superior catalytic activity of Ce-MnO_x can be ascribed to its more content and enhanced formation ability of oxygen vacancies, larger specific surface area and higher oxygen mobility. Furthermore, the durability tests under high relative humidity (80%) determined that Ce-MnO_x showed excellent stability and water resistance. These demonstrate the promising potential of amorphously Ce-modified manganese oxides for catalytic removal of ozone.

Polyaromatic hydrocarbon thin film layers on glass, dust, and polyurethane foam surfaces

An investigation was conducted into the dynamic behavior of two polyaromatic hydrocarbon (PAH) semi-volatile organic compound (SVOC) naphthalene (NAP) and benzo [ghi]perylene (BghiP) in air and on various surfaces including glass, dust, and polyurethane foam (PUF) to understand their interaction with different media. A confocal fluorescence microscope and an infrared microscope were employed to detect and monitor the concentration-, time-, and temperature-dependent changes of the aromatic NAP and BghiP species on the surfaces. Infrared two-dimensional mapping of the vibrational characteristic peaks was used to track the two PAHs on the surfaces. Gas chromatography-mass spectrometry (GC-MS) was employed to measure the gaseous concentrations. The sorption of NAP and BghiP on the surfaces was estimated using Arizona desert sand fine (ISO 12103-1 A2) dust and organic contaminant household (SRM 2585) dust. The surface-to-air partition coefficients of NAP and BghiP were estimated on the different surfaces of glass, dust, and PUF. Molecular dynamic simulations were performed on dust surfaces based on the Hatcher model to understand the behavior of NAP and BghiP on dust surfaces. The Weschler-Nazaroff model was introduced to predictPAH film accumulation on the surfaces, providing a better understanding of PAH interaction with different environmental media. These findings could contribute to developing effective strategies to mitigate the adverse impact of PAHs on the environment and human health.

Occurrence and risk of human exposure to organophosphate flame retardants in indoor air and dust in Hanoi, Vietnam

The presence and distribution of thirteen organophosphate flame retardants (OPFRs) were investigated in indoor air and dust samples collected in Hanoi, Vietnam. The total OPFRs (ƩOPFRs) concentrations in indoor air and dust samples were 42.3-358 ng m^-3 (median 101 ng m^-3) and 1290-17,500 ng g^-1 (median 7580 ng g^-1), respectively. The profile of OPFRs in both indoor air and dust indicated that tris(1-chloro-2-propyl) phosphate (TCIPP) was the most dominant compound with a median concentration of 75.3 ng m^-3 and 3620 ng g^-1, contributing 75.2% and 46.1% to ƩOPFRs concentrations in indoor air and dust, respectively, followed by tris(2-butoxyethyl) phosphate (TBOEP), with a median concentration of 16.3 ng m^-3 and 2500 ng g^-1, contributing 14.1% and 33.6% to ƩOPFRs concentrations in indoor air and dust, respectively. The levels of OPFRs in the indoor air samples and corresponding indoor dust samples showed a strong positive correlation. The total estimated daily intakes (EDI_total) of ƩOPFRs (via air inhalation, dust ingestion, and dermal absorption) for adults and toddlers under the median and high exposure scenarios were 36.7 and 160 ng kg^-1 d^-1, and 266 and 1270 ng kg^-1 d^-1, respectively. Among the investigated exposure pathways, dermal absorption was a primary exposure pathway to OPFRs for both toddlers and adults. The hazard quotients (HQ) ranged from 5.31 × 10^-8 to 6.47 × 10^-2 (<1), and the lifetime cancer risks (LCR) were from 2.05 × 10^-11 to 7.37 × 10^-8 (<10^-6), indicating that human health risks from exposure to OPFRs in indoor environments are not significant.

Numerical Simulations of Synthetic Ester Hydrolysis in the Indoor Environment

The hydrolysis of synthetic esters (SEs), including phthalates and adipates, in damp indoor environments can lead to the release of volatile organic compounds implicated in poor air quality and acute health impacts, known as "sick building syndrome" (SBS). We have adapted the multiphase atmospheric chemistry box model, GAMMA, to simulate SE hydrolysis occurring in surface films in the indoor environment, along with multilayer boundary layer mass transfer and ventilation, in order to investigate this phenomenon on a process level. We then applied the model to analyze three scenarios in which hydrolysis has been hypothesized to have a significant impact on indoor air quality. Simulation results suggest that (1) alkaline hydrolysis of bis(2-ethylhexyl) adipate (DEHA) and bis(2-ethylhexyl) phthalate (DEHP) from PVC flooring on damp surfaces alone is not sufficient to explain the levels of 2-ethylhexanol reported in indoor air during episodes of SBS; (2) acute exposure to 2,2,4-trimethyl-1,3-pentanediol (TMPD) may be of concern during and shortly after the application of latex paint on an alkaline surface; and (3) alkaline hydrolysis of SEs following their airborne uptake in aqueous films is not expected to generate considerable amounts of alcohols associated with SBS.

Distribution of polycyclic aromatic hydrocarbons in indoor/outdoor window films and the indoor film/air partition of northeastern Chinese college dormitories

Indoor window films can represent short-term air pollution conditions of indoor environment through rapidly capturing organic contaminants as effective passive air samplers. To investigate the temporal variation, influence factors of polycyclic aromatic hydrocarbons (PAHs) in indoor window films, and the exchange behavior with gas phase in college dormitories, 42 pairs window films of interior and exterior window surfaces and corresponding indoor gas phase and dust samples were collected monthly in six selected dormitories, Harbin, China, from August to December 2019 and September 2020. The average concentration of ∑₁₆PAHs in indoor window films (398 ng/m²) was significantly (p < 0.01) lower than that in outdoors (652 ng/m²). In addition, the median indoor/outdoor ∑₁₆PAHs concentration ratio was close to 0.5, showing that outdoor air acted as a major PAH source to indoor environment. The 5-ring PAHs were mostly dominant in window films whereas the 3-ring PAHs contributed mostly in gas phase. 3-ring PAHs and 4-ring PAHs were both important contributors for dormitory dust. Window films showed stable temporal variation, i.e. PAH concentrations in heating months were higher than those in non-heating months. The atmospheric O₃ concentration was the main influence factor of PAHs in indoor window films. PAHs with low molecular weight in indoor window films rapidly reached film/air equilibrium phase within in dozens of hours. The large deviation in the slope of the log K_F-A versus log K_OA regression line from that in reported equilibrium formula might be the difference between the window film composition and octanol.

A rapid micro chamber method to measure SVOC emission and transport model parameters

Assessing exposure to semivolatile organic compounds (SVOCs) that are emitted from consumer products and building materials in indoor environments is critical for reducing the associated health risks. Many modeling approaches have been developed for SVOC exposure assessment indoors, including the DustEx webtool. However, the applicability of these tools depends on the availability of model parameters such as the gas-phase concentration at equilibrium with the source material surface, y₀, and the surface-air partition coefficient, K_s, both of which are typically determined in chamber experiments. In this study, we compared two types of chamber design, a macro chamber, which downscaled the dimensions of a room to a smaller size with roughly the same surface-to-volume ratio, and a micro chamber, which minimized the sink-to-source surface area ratio to shorten the time required to reach steady state. The results show that the two chambers with different sink-to-source surface area ratios yield comparable steady-state gas- and surface-phase concentrations for a range of plasticizers, while the micro chamber required significantly shorter times to reach steady state. Using y₀ and K_s measured with the micro chamber, we conducted indoor exposure assessments for di-n-butyl phthalate (DnBP), di(2-ethylhexyl) phthalate (DEHP) and di(2-ethylhexyl) terephthalate (DEHT) with the updated DustEx webtool. The predicted concentration profiles correspond well with existing measurements and demonstrate the direct applicability of chamber data in exposure assessments.

Phthalates in glass window films are associated with dormitory characteristics, occupancy activities and habits, and environmental factors

Phthalates are environmental endocrine disruptors that enter the human body through a variety of pathways and harm human health. The study aimed to explore the associations between phthalate concentrations in glass window films with dormitory characteristics, occupancy activities and habits, and environmental factors, of university dormitories. We surveyed these associations and measured the indoor environmental parameters of 144 dormitories from 13 universities in Beijing. Based on the results, we further explored the factors affecting phthalate concentrations using multivariate logistic regression. The results showed that phthalate concentrations in glass window films were associated with dormitory type, duration of occupancy, daily ventilation duration, window cleaning frequency, indoor relative humidity, light intensity, temperature, and particulate matter (PM₁₀) concentration. To date, there have only been a few studies on the factors that influence phthalate concentrations in glass window films; therefore, further study is needed. Our findings determined the influence of external factors on the different types of phthalates in window films, which helps understand indoor phthalate pollution and evaluate human exposure based on phthalate concentrations in glass window films.

Evaluating the dynamic distribution process and potential exposure risk of chlorinated paraffins in indoor environments of Beijing, China

Chlorinated paraffins (CPs) are typical semi-volatile chemicals (SVOCs) that have been used in copious quantities in indoor material additives. SVOCs distribute dynamically between the gas phase and various condensate phases, especially organic films. Investigating the dynamic behaviors of existing CPs in indoor environments is necessary for understanding their potential risk to humans from indoor exposure. We investigate the distribution profiles of CPs in both gas phase and organic films in indoor environments of residential buildings in Beijing, China. The concentrations of CPs were in the range of 32.21-1447 ng/m³ in indoor air and in the range of 42.30-431.1 μg/m² and in organic films. Cooking frequency was identified as a key factor that affected the distribution profiles of CPs. Furthermore, a film/gas partitioning model was constructed to explore the transportation and fate of CPs. Interestingly, a re-emission phenomenon from organic films was observed for chemical groups with lower log K_oa components, and, importantly, their residue levels in indoor air were well predicted. The estimated exposure risk of CPs in indoor environment was obtained. For the first time, these results produced convincing evidence that the co-exposure risk of short-chain CPs (SCCPs), medium-chain CPs (MCCPs), and long-chain CPs (LCCPs) in indoor air could be further increased by film/gas distribution properties, which is relevant for performing risk assessments of exposure to these SVOCs in indoor environments.

Partitioning of reactive oxygen species from indoor surfaces to indoor aerosols

Reactive oxygen species (ROS) are among the species thought to be responsible for the adverse health effects of particulate matter (PM) inhalation. Field studies suggest that indoor sources of ROS contribute to measured ROS on PM in indoor air. We hypothesize that ozone reacts on indoor surfaces to form semi-volatile ROS, in particular organic peroxides (OPX), which partition to airborne particles. To test this hypothesis, we modeled ozone-induced formation of OPX, its decay and its partitioning to PM in a residential building and compared the results to field measurements. Simulations indicate that, while ROS of outdoor origin is the primary contributor to indoor ROS (in PM), a substantial fraction of ROS present in indoor PM is from ozone-surface chemistry. At an air change rate equal to 1/h, and an outdoor ozone mixing ratio of 35 ppb, 25% of the ROS concentration in air is due to indoor formation and partitioning of OPX to PM. For the same conditions, but with a modest indoor source of PM (1.5 mg h^-1), 44% of indoor ROS on PM is of indoor origin. An indoor source of ozone, such as an electrostatic air cleaner, also increases OPX present in indoor PM. The results of the simulations support the hypothesis that ozone-induced formation of OPX on indoor surfaces, and subsequent partitioning to aerosols, is sufficient to explain field observations. Therefore, indoor sourced ROS could contribute meaningfully to total inhaled PM-ROS.

Indoor partitioning and potential thirdhand exposure to carbonyl flavoring agents added in e-cigarettes and hookah tobacco

Flavoring agents added to the e-cigarettes and hookah tobacco have increased the attractiveness of novel nicotine products. Many widely used flavorings are carbonyls, which are toxic to humans. In an indoor environment, residents can be exposed to such harmful flavorings previously emitted to the surrounding environment, through a process termed thirdhand exposure. The recent discovery of a large volume of indoor reservoirs emphasizes the importance of indoor partitioning, which is responsible for thirdhand exposure. Indoor partitioning can be expressed with partitioning coefficients, such as Henry's law solubility constant (H). However, reliable H values for many key flavorings are currently lacking. To better understand their environmental behavior, this study experimentally determined the effective Henry's law constant (Hcps,eff) using the inert gas stripping (IGS) method. Further, the influence of the hydration process for target flavorings was quantified using proton nuclear magnetic resonance (¹H NMR) spectroscopy. We found that hydration of α-dicarbonyls (diacetyl and 2,3-pentanedione) enhanced their Hcps,eff from their intrinsic Henry's law constant (Hcps) by a factor of 3.52 and 2.88, respectively. The two-dimensional partitioning plots were employed to simulate the indoor phase distribution and evaluate the pathways of human exposure. Our findings show that the indoor partitioning of many harmful flavorings is highly sensitive to temperature and the size of indoor reservoirs, indicating that residents are likely to experience third-hand exposure.

A review of indoor Gaseous organic compounds and human chemical Exposure: Insights from Real-time measurements

Gaseous organic compounds, mainly volatile organic compounds (VOCs), have become a wide concern in various indoor environments where we spend the majority of our daily time. The sources, compositions, variations, and sinks of indoor VOCs are extremely complex, and their potential impacts on human health are less understood. Owing to the deployment of the state-of-the-art real-time mass spectrometry during the last two decades, our understanding of the sources, dynamic changes and chemical transformations of VOCs indoors has been significantly improved. This review aims to summarize the key findings from mass spectrometry measurements in recent indoor studies including residence, classroom, office, sports center, etc. The sources and sinks, compositions and distributions of indoor VOCs, and the factors (e.g., human activities, air exchange rate, temperature and humidity) driving the changes in indoor VOCs are discussed. The physical and chemical processes of gas-particle partitioning and secondary oxidation processes of VOCs, and their impacts on human health are summarized. Finally, the recommendations for future research directions on indoor VOCs measurements and indoor chemistry are proposed.

Accumulations and equilibrium conditions of organophosphate esters (OPEs) in the indoor window film and the estimation of concentrations in air

The study of the fate of organophosphate esters (OPEs) in the interior environment is vital because of the growing use of OPEs. Organic films on glass are both sink and sources of indoor pollutants. Indoor window films have been employed as passive air samplers to collect OPEs in the indoor air. Nevertheless, little is known about the development and equilibrium condition of OPEs on indoor window films during the film formation process. In this study, the concentrations of twelve OPEs in indoor window films from different buildings on a university campus and the growth thickness of the films as a function of sampling time were investigated in different seasons. Ten out of the 12 OPEs were detected in window film with >50 % frequency. Tris (2-chloroethyl) phosphate (TCEP) and tris (1-chloro-2-propyl) phosphate (TCPP), which are chlorinated and toxic OPEs, were the dominant OPEs found in the winter. The majority of OPEs in window films exhibited linear growth patterns within 77 days. Temperature, humidity, ventilation, and seasonality all affected the concentrations of various OPEs in the window films. Low molecular weight OPEs, such as tri-n-butyl phosphate and TCEP, attained equilibrium between indoor air and window films within 49 or 77 days. The indoor air concentrations of OPEs were estimated from their film concentrations based on the theoretical approach for the passive air sampler. In winter, the predicted gas-phase air concentrations of OPEs (3.7 ng/m³ for TECP) were significantly lower than or comparable to summer (11 ng/m³, p < 0.05). To the best of our knowledge, this is the first attempt to combine uncertainty and sensitivity analysis to understand the behaviors of OPEs in indoor film and air.

Reactive Chlorine Emissions from Cleaning and Reactive Nitrogen Chemistry in an Indoor Athletic Facility

Indoor gas-phase radical sources are poorly understood but expected to be much different from outdoors. Several potential radical sources were measured in a windowless, light-emitting diode (LED)-lit room in a college athletic facility over a 2 week period. Alternating measurements between the room air and the supply air of the heating, ventilation, and air-conditioning system allowed an assessment of sources. Use of a chlorine-based cleaner was a source of several photolabile reactive chlorine compounds, including ClNO₂ and Cl₂. During cleaning events, photolysis rates for these two compounds were up to 0.0023 pptv min^-1, acting as a source of chlorine atoms even in this low-light indoor environment. Unrelated to cleaning events, elevated ClNO₂ was often observed during daytime and lost to ventilation. The nitrate radical (NO₃), which is rapidly photolyzed outdoors during daytime, may persist in low-light indoor environments. With negligible photolysis, loss rates of NO₃ indoors were dominated by bimolecular reactions. At times with high NO₂ and O₃ ventilated from outdoors, N₂O₅ was observed. Elevated ClNO₂ measured concurrently suggests the formation through heterogeneous reactions, acting as an additional source of reactive chlorine within the athletic facility and outdoors.

Host surface orientation impacts environmental film accumulations

Two environmental films were passively collected in different orientations (vertical or horizontal) at the same location over two months. We characterized these films using bright field microscopy, total dissolved species analysis, pH analysis, vibrational interfacial spectroscopy, and contact angle goniometry. Results show that horizontal films have significantly higher surface coverage than the vertical samples (+50%). The vertical and horizontal films also show different particle morphologies but the particle size distributions are not statistically different. Vertical surfaces have smaller, less compact particulate suggesting particle adsorption depends on the surface area in contact with the parent substrate. Horizontal surfaces also generate more total dissolved solid material per unit area when washed with water (+61%). The dissolved solids from the vertical substrate are more acidic per unit mass, suggesting increased pH active species like nitrate, sulfate, or organic acids. Vibrational spectroscopy provides evidence of nitrates and sulfates in both films, but spectroscopic profiles show these ions are present in different forms. Contact angle goniometry measurements show horizontal films are more hydrophilic than vertical films, despite being deposited on the same substrate material. We also report significantly different hydrogen bonding environments for condensed water between the two films. Our results suggest that environmental films deposited on vertical vs horizontal surfaces will have significantly different characteristics, informing models for deposition and impacts to human and environmental health.

Analysis of semi-volatile organic compounds in indoor dust and organic thin films by house type in South Korea

In this study, semi-volatile organic compounds (SVOCs) in samples of indoor dust and organic thin films obtained from 100 residential houses in South Korea, were examined, based on both target analysis using gas chromatography-mass spectrometry (GC-MS) and non-target analysis by gas chromatography-quadrupole time-of flight mass spectrometry (GC-QTOF-MS) screening. In the targeted approach, phthalates and polycyclic aromatic hydrocarbons (PAHs) were analyzed in dust and organic film samples, to find that both these classes of SVOCs were detected in dust and organic film samples, with the median concentrations of eight phthalates (Σ₈ phthalate) and 16 PAHs (Σ₁₆ PAH) being 1015.93 μg/g and 1824.97 ng/g in the dust samples, and 75.79 μg/m² and 2252.78 ng/m² in the organic film samples, respectively. Among the phthalates, in all house types. bis(2-ethylhexyl) phthalate (DEHP) was detected at the highest concentration, followed by dibutyl phthalate (DBP) and diisobuthyl phthalate (DiBP), with DEHP levels found to be highest in dwelling houses. DEHP levels were found to be significantly associated with building age and renovation status. Lower levels of DEHP were detected in houses less than 10 years old or that had undergone renovation in the previous 10 years. Among the assessed PAHs, a significant correlation was detected between benzo(a)pyrene in dust and building age (p < 0.05). These findings imply that the inhabitants of older houses are at a greater risk of exposure to SVOCs originating from indoor dust and organic films. Non-target screening of selected dust and organic film samples using GC-QTOF-MS data revealed the presence of numerous SVOC compounds, including triphenylphosphine oxide, (Z)-9-octadecenamide, and cyclosiloxanes, along with certain organophosphate flame retardants including tris(1-chloro-2-propyl) phosphate (TCPP) and tris(1,3-dichloroisopropyl) phosphate (TDCPP), and plasticizers. These compounds identified in the non-target screening are of emerging concern, and their presence in dust and organic films needs to be estimated.

Phase state of organic aerosols may limit temperature-driven thermodynamic repartitioning following outdoor-to-indoor transport

Ambient aerosols often experience temperature and humidity gradients following outdoor-to-indoor transport, causing organic aerosols (OA) to either gain or lose mass via gas-particle repartitioning. Recent models have sought to quantify these effects using equilibrium partitioning thermodynamics. However, evidence suggests some indoor OA may possess glassy or semisolid phase states with higher viscosities than liquid OA. Characteristic partitioning timescales of higher-viscosity particles are significantly longer than for liquid particles, which may either fully or partially inhibit repartitioning. For outdoor OA experiencing a temperature change during transport indoors, the ultimate repartitioning state depends on the relationship between the gas-particle partitioning rate coefficient (k_gp) of semivolatile organics and the indoor particle loss rate coefficient (l_p). That is, thermodynamic equilibrium partitioning may occur when semivolatile k_gp ≫ l_p, no repartitioning when semivolatile k_gp ≪ l_p, and partial repartitioning when their magnitudes are similar. Longer indoor particle lifetimes, higher particle number, and larger particle sizes all raise k_gp (driving repartitioning towards equilibrium). For simulated U.S. residences, equilibrium condensation was likely reached in humid climate zones during warm meteorological conditions. In colder regions, the degree of evaporative repartitioning depended on whether organics could repartition before the particle phase state adjusts to indoor conditions, which is uncertain. When an appreciable temperature gradient exists, this study not only confirmed that all outdoor-originating OA that is liquid indoors will reach thermodynamic equilibrium, but also concluded that a plurality (46% for this domain) of such OA that is semisolid may also achieve thermodynamic equilibrium during its indoor lifetime.

Recent advances on SOA formation in indoor air, fate and strategies for SOA characterization in indoor air - A review

Recent studies proves that indoor air chemistry differs in many aspects from atmospheric one. People send up to 90 % of their life indoors being exposed to pollutants present in gas, particle and solid phase. Particle phase indoor is composed of particles emitted from various sources, among which there is an indoor source - secondary chemical reactions leading to formation of secondary organic aerosol (SOA). Lately, researchers' attentions turned towards the ultrafine particles, for there are still a lot of gaps in knowledge concerning this field of study, while there is evidence of negative influence of ultrafine particles on human health. Presented review sums up current knowledge about secondary particle formation in indoor environment and development of analytical techniques applied to study those processes. The biggest concern today is studying ROS, for their lifetime in indoor air is very short due to reactions at the very beginning of terpene oxidation process. Another interesting aspect that is recently discovered is monoterpene autooxidation process that leads to HOMs formation that in turn can influence SOA formation yield. A complex studies covering gas phase and particle phase characterization, but also toxicological studies are crucial to fully understand indoor air chemistry leading to ultrafine particle formation.

Estimated daily intake of per- and polyfluoroalkyl substances related to different particle size fractions of house dust

Indoor environmental pollutants are a threat to human health. In the current study, we analysed 25 per- and polyfluoroalkyl substances (PFASs) in seven different size fraction of house dust including the two relevant for exposure via ingestion and inhalation. The highest PFAS concentration is found in the inhalable particulate fraction which is explained by the increased surface area as the particulate's sizes decrease. The estimated daily intake (EDI) of the individual PFAS and exposure pathways were calculated for children and adults. In addition, the total EDI for PFOA and its precursors was estimated. The polyfluoroalkyl phosphoric acid diesters (diPAP), followed by PFOA and PFHxA fluortelomer, showed the highest concentrations of PFAS analysed. The cumulative EDI of PFAS for children was 3.0 ng/kg bw per day, a worst-case scenario, which is 17 times higher than the calculated EDI for adults. For children, ingestion of dust was found to result in 800 times higher PFOA exposure than via inhalation. The contribution from PFOA precursors corresponded to only 1% of the EDI from dust indicating PFOA as the main source of exposure. The EDI's of PFOA and PFOS from dust were lower than the calculated EDI's from food ingestion reported by the Swedish Food Agency. Our data indicate that the EDI for the sum of four PFASs: PFOA, PFNA, PFHxS and PFOS from dust intake alone is close to the established tolerable weakly intake of 4.4 ng/kg bw in children, set by European Food Safety Authority (EFSA) in 2020. The combined EDI levels PFOA and PFOS from both dust and food exceeded the EFSA TWI for both children and adults. This study demonstrates that dust is a relevant exposure pathway for PFAS intake and that analysis of relevant particle size fractions is important for evaluation of dust as an exposure pathway.

Strong temperature influence and indiscernible ventilation effect on dynamics of some semivolatile organic compounds in the indoor air of an office

Many manmade organic air pollutants are semivolatile and primarily used and exposed indoors. It remains unclear how indoor environmental parameters affect indoor air dynamics of semivolatile organic compounds (SVOCs) in real-world indoor conditions, which directly relates to human exposure. By making time-resolved SVOC measurements over multiple weeks in an office, we characterized the indoor air dynamics of six representative SVOCs which were mainly present in the gas phase and of indoor origins, and investigated the effects of the temperature and ventilation rate. The six species include di-isobutyl phthalate and di-n-butyl phthalate, as well as two n-alkanes and two siloxanes. Airborne concentrations of all six SVOCs responded strongly and quickly to changes in the indoor temperature. The temperature dependence of individual species can be well fitted in the form of the van't Hoff equation, and explained 65-86% of the observed variation in the logarithm-transformed concentrations. In contrast, increasing the ventilation rate by a factor of 3-5 for hours at a constant temperature had no discernible influence on the SVOC concentrations. Further kinetic modeling analysis suggests that the observed fast temperature response and indiscernible ventilation effect are both associated with SVOC sorption onto indoor surfaces, which dramatically slows the response of SVOC concentration to changes in the ventilation rate and speeds up the response to changes in the temperature. These results highlight the importance of sorption reservoirs on regulating indoor SVOC dynamics and also have important implications for controlling and assessing indoor air exposure to SVOCs.

Henry's Law Constants and Indoor Partitioning of Microbial Volatile Organic Compounds

Microbial volatile organic compounds (MVOCs) play an essential role in many environmental fields, such as indoor air quality. Long-term exposure to odorous and toxic MVOCs can negatively affect the health of occupants. Recently, the involvement of surface reservoirs in indoor chemistry has been realized, which signifies the importance of the phase partitioning of volatile organic pollutants. However, reliable partition coefficients of many MVOCs are currently lacking. Equilibrium partition coefficients, such as Henry's law constant, H, are crucial for understanding the environmental behavior of chemicals. This study aims to experimentally determine the H values and their temperature dependence for key MVOCs under temperature relevant to the indoor environment. The H values were determined with the inert gas-stripping (IGS) method and variable phase ratio headspace (VPR-HS) technique. A two-dimensional partitioning model was applied to predict the indoor phase distribution of MVOCs and potential exposure pathways to the residences. The findings show that the MVOCs are likely distributed between the gas and weakly polar (e.g., organic-rich) reservoirs indoors. Temperature and the volume of reservoirs can sensitively affect indoor partitioning. Our results give a more comprehensive view of indoor chemical partitioning and exposure.

A modular mechanistic framework for estimating exposure to SVOCs: Next steps for modeling emission and partitioning of plasticizers and PFAS

Estimates of human exposure to semi-volatile organic compounds (SVOCs) such as phthalates, phthalate alternatives, and some per- and polyfluoroalkyl substances (PFAS) are required for the risk-based evaluation of chemicals. Recently, a modular mechanistic modeling framework to rapidly predict SVOC emission and partitioning in indoor environments has been presented, in which several mechanistically consistent source emission categories (SECs) were identified. However, not all SECs have well-developed emission models. In addition, data on model parameters are missing even for frequently studied SVOCs. These knowledge gaps impede the comprehensive prediction of the fate of SVOCs indoors. In this paper, sets of high-priority phthalates, phthalate alternatives, and PFAS were identified based on chemical occurrence indoors and additional selection criteria. These high-priority chemicals served as the basis for exploring model parameter availability for existing indoor SVOC emission and partitioning models. The results reveal that additional experimental and modeling work is needed to fully understand the behavior of SVOCs indoors and to predict exposures with greater confidence and lower uncertainty. Modeling approaches to fill some of the identified gaps are proposed. The prioritized sets of chemicals and proposed new modeling approaches will help guide future research. The inclusion of polar phases in the framework will further expand its applicability and scope. IMPACT STATEMENT: This paper compiles data on high-priority chemicals commonly found indoors and information on the availability of applicable models and model parameters to predict emission, partitioning, and subsequent exposure to these chemicals. Modeling approaches for a selection of the missing SECs (source emission categories) are proposed, to illustrate the path forward. The comprehensive data set helps inform researchers, exposure assessors, and policy makers to better understand the state of the science regarding modeling of indoor exposure to semi-volatile organic compounds (SVOCs) and per- and polyfluoroalkyl substances (PFAS).

Temperature and indoor environments

From the thermodynamic perspective, the term temperature is clearly defined for ideal physical systems: A unique temperature can be assigned to each black body via its radiation spectrum, and the temperature of an ideal gas is given by the velocity distribution of the molecules. While the indoor environment is not an ideal system, fundamental physical and chemical processes, such as diffusion, partitioning equilibria, and chemical reactions, are predictably temperature-dependent. For example, the logarithm of reaction rate and equilibria constants are proportional to the reciprocal of the absolute temperature. It is therefore possible to have non-linear, very steep changes in chemical phenomena over a relatively small temperature range. On the contrary, transport processes are more influenced by spatial temperature, momentum, and pressure gradients as well as by the density, porosity, and composition of indoor materials. Consequently, emergent phenomena, such as emission rates or dynamic air concentrations, can be the result of complex temperature-dependent relationships that require a more empirical approach. Indoor environmental conditions are further influenced by the thermal comfort needs of occupants. Not only do occupants have to create thermal conditions that serve to maintain their core body temperature, which is usually accomplished by wearing appropriate clothing, but also the surroundings must be adapted so that they feel comfortable. This includes the interaction of the living space with the ambient environment, which can vary greatly by region and season. Design of houses, apartments, commercial buildings, and schools is generally utility and comfort driven, requiring an appropriate energy balance, sometimes considering ventilation but rarely including the impact of temperature on indoor contaminant levels. In our article, we start with a review of fundamental thermodynamic variables and discuss their influence on typical indoor processes. Then, we describe the heat balance of people in their thermal environment. An extensive literature study is devoted to the thermal conditions in buildings, the temperature-dependent release of indoor pollutants from materials and their distribution in the various interior compartments as well as aspects of indoor chemistry. Finally, we assess the need to consider temperature holistically with regard to the changes to be expected as a result of global emergencies such as climate change.

Surface-dependent gas equilibrium of semi-volatile organic compounds on glass, wood, and polyurethane foam using SPME-GC/MS

The surface-dependent evaporation behavior of phthalates as semi-volatile organic compounds (SVOCs) on glass, wood, and polyurethane foam (PUF) was investigated. Three phthalates of di-2-ethylhexyl phthalate (DEHP), butyl benzyl phthalate (BBP), and dibutyl phthalate (DBP) were studied to compare the amount of gases vaporized from their surfaces. A 10 mL silicate glass vial was used to compare the gas equilibrium of the phthalates after 2 h. The gases accumulated in the air were transferred to a solid-phase microextraction (SPME) column and analyzed by gas chromatography-mass spectrometry (GC-MS). As correlated with the physicochemical properties of the phthalates, including molecular weights and vapor pressure, the surface-air partition coefficients (K_sa) were found to be in the range of 10¹-10⁵ m, 10⁶-10⁷ m, and 10⁷-10⁹ m on glass, wood, and PUF, respectively, implying that a significant amount of phthalates are retained on wood and PUF surfaces as compared to glass, and only a trace amount of phthalates can be volatilized into the air, especially the less volatile DEHP. The three-dimensional (3D) morphologies of glass and wood were also examined using a white-light interferometric surface profile microscope and an atomic force microscope (AFM). In contrast to smooth glass surfaces within the sub-micrometer vertical range, the wood surfaces exhibited uneven irregular structures at a height of 5-30 μm. The rough wood surfaces were found to adsorb substantial amounts of gases to prevent the effective volatilization of phthalates into the air, especially the low molecular DBP. Our results imply that wood and PUF surfaces may be superior to glass surfaces in storage and reduction of phthalates in the air, especially DBP.

Partitioning of airborne PAEs on indoor impermeable surfaces: A microscopic view of the sorption process

Organic films were widely found on indoor impermeable surfaces exposed to gaseous organic compounds, but few studies have addressed the film growth details on different indoor substrates. In this study, we observed the topography evolution of phthalic acid ester (PAE) organic films on three impermeable substrates: polished glass (G-P), mirror-polished stainless steel (SS-M) and drawn stainless steel (SS-D). PAE organic films were preferentially formed upon the flat surface with sparse inherent nano-peaks of substrate G-P and in valleys of substrate SS-M and SS-D. Surface uniformity of substrates and viscosity of PAE molecules were inferred as critical parameters determining the surface average adhesion forces. We obtained the partition coefficients of DEP, DnBP, BBP and DEHP on substrate G-P, SS-M and SS-D by fitting the initial monolayer adsorption process. Organic films continuously grew instead of reaching adsorption equilibrium after long-term PAE exposure, indicating that multilayer adsorption may occur. The organic film growth rates in saturated gas-phase PAE concentrations were quantified as about one-tenth of the results in previous studies where substrates were simultaneously exposed to multiple pollutants. To sum up, the results outline PAE adsorption details on impermeable materials and provide a reference for better estimation on PAE exposure assessment.

Nanoscopic Study of Water Uptake on Glass Surfaces with Organic Thin Films and Particles from Exposure to Indoor Cooking Activities: Comparison to Model Systems

Water uptake by thin organic films and organic particles on glass substrates at 80% relative humidity was investigated using atomic force microscopy-infrared (AFM-IR) spectroscopy. Glass surfaces exposed to kitchen cooking activities show a wide variability of coverages from organic particles and organic thin films. Water uptake, as measured by changes in the volume of the films and particles, was also quite variable. A comparison of glass surfaces exposed to kitchen activities to model systems shows that they can be largely represented by oxidized oleic acid and carboxylate groups on long and medium hydrocarbon chains (i.e., fatty acids). Overall, we demonstrate that organic particles and thin films that cover glass surfaces can take up water under indoor-relevant conditions but that the water content is not uniform. The spatial heterogeneity of the changes in these aged glass surfaces under dry (5%) and wet (80%) conditions is quite marked, highlighting the need for studies at the nano- and microscale.

Indoor heterogeneous photochemistry of molds and their contribution to HONO formation

To better understand the impact of molds on indoor air quality, we studied the photochemistry of microbial films made by Aspergillus niger species, a common indoor mold. Specifically, we investigated their implication in the conversion of adsorbed nitrate anions into gaseous nitrous acid (HONO) and nitrogen oxides (NO_x ), as well as the related VOC emissions under different indoor conditions, using a high-resolution proton transfer reaction-time of flight-mass spectrometer (PTR-TOF-MS) and a long path absorption photometer (LOPAP). The different mold preparations were characterized by the means of direct injection into an Orbitrap high-resolution mass spectrometer with a heated electrospray ionization (ESI-Orbitrap-MS). The formation of a wide range of VOCs, having emission profiles sensitive to the types of films (either doped by potassium nitrate or not), cultivation time, UV-light irradiation, potassium nitrate concentration and relative humidity was observed. The formation of nitrous acid from these films was also determined and found to be dependent on light and relative humidity. Finally, the reaction paths for the NO_x and HONO production are proposed. This work helps to better understand the implication of microbial surfaces as a new indoor source for HONO emission.

Indoor ozone: Concentrations and influencing factors

Because people spend most of their time indoors, much of their exposure to ozone occurs in buildings, which are partially protective against outdoor ozone. Measurements in approximately 2000 indoor environments (residences, schools, and offices) show a central tendency for average indoor ozone concentration of 4-6 ppb and an indoor to outdoor concentration ratio of about 25%. Considerable variability in this ratio exists among buildings, as influenced by seven building-associated factors: ozone removal in mechanical ventilation systems, ozone penetration through the building envelope, air-change rates, ozone loss rate on fixed indoor surfaces, ozone loss rate on human occupants, ozone loss by homogeneous reaction with nitrogen oxides, and ozone loss by reaction with gas-phase organics. Among these, the most important are air-change rates, ozone loss rate on fixed indoor surfaces, and, in densely occupied spaces, ozone loss rate on human occupants. Although most indoor ozone originates outdoors and enters with ventilation air, indoor emission sources can materially increase indoor ozone concentrations. Mitigation technologies to reduce indoor ozone concentrations are available or are being investigated. The most mature of these technologies, activated carbon filtration of mechanical ventilation supply air, shows a high modeled health-benefit to cost ratio when applied in densely occupied spaces.

Influence of Mechanical Ventilation Systems and Human Occupancy on Time-Resolved Source Rates of Volatile Skin Oil Ozonolysis Products in a LEED-Certified Office Building

Building mechanical ventilation systems are a major driver of indoor air chemistry as their design and operation influences indoor ozone (O₃) concentrations, the dilution and transport of indoor-generated volatile organic compounds (VOCs), and indoor environmental conditions. Real-time VOC and O₃ measurements were integrated with a building sensing platform to evaluate the influence of mechanical ventilation modes and human occupancy on the dynamics of skin oil ozonolysis products (SOOPs) in an office in a LEED-certified building during the winter. The ventilation system operated under variable recirculation ratios (RRs) from RR = 0 (100% outdoor air) to RR = 1 (100% recirculation air). Time-resolved source rates for 6-methyl-5-hepten-2-one (6-MHO), 4-oxopentanal (4-OPA), and decanal were highly dynamic and changed throughout the day with RR and occupancy. Total SOOP source rates during high-occupancy periods (10:00-18:00) varied from 2500-3000 μg h^-1 when RR = 0.1 to 6300-6700 μg h^-1 when RR = 1. Source rates for gas-phase reactions, outdoor air, and occupant-associated emissions generally decreased with increasing RR. The recirculation air source rate increased with RR and typically became the dominant source for RR > 0.5. SOOP emissions from surface reservoirs were also a prominent source, contributing 10-50% to total source rates. Elevated per person SOOP emission factors were observed, potentially due to multiple layers of soiled clothing worn during winter.

Emerging investigator series: the role of chemical properties in human exposure to environmental chemicals

One of the ultimate goals of environmental exposure science is to mechanistically understand how chemical properties and human behavior interactively determine human exposure to the wide spectrum of chemicals present in the environment. This comprehensive review assembles state-of-the-art knowledge of the role of partitioning, dissociation, mass transfer, and reactive properties in human contact with and absorption of organic chemicals via oral, dermal, and respiratory routes. Existing studies have revealed that chemicals with different properties vary greatly in mass distribution and occurrence among multiple exposure media, resulting in distinct patterns of human intake from the environment. On the other hand, these chemicals encounter different levels of resistance in the passage of intestinal, dermal, and pulmonary absorption barriers and demonstrate different levels of bioavailability, due to the selectivity of biochemical, anatomical and physiological structures of these absorption barriers. Moving forward, the research community needs to gain more in-depth mechanistic insights into the complex processes in human exposure, advance the technique to better characterize and predict chemical properties, generate and leverage experimental data for a more diverse range of chemicals, and describe better the interactions between chemical properties and human behavior.

Kinetic multi-layer model of film formation, growth, and chemistry (KM-FILM): Boundary layer processes, multi-layer adsorption, bulk diffusion, and heterogeneous reactions

Large surface area-to-volume ratios indoors cause heterogeneous interactions to be especially important. Semi-volatile organic compounds can deposit on impermeable indoor surfaces forming thin organic films. We developed a new model to simulate the initial film formation by treating gas-phase diffusion and turbulence through a surface boundary layer and multi-layer reversible adsorption on rough surfaces, as well as subsequent film growth by resolving bulk diffusion and chemical reactions in a film. The model was applied with consistent parameters to reproduce twenty-one sets of film formation measurements due to multi-layer adsorption of multiple phthalates onto different indoor-relevant surfaces, showing that the films should initially be patchy with the formation of pyramid-like structures on the surface. Sensitivity tests showed that highly turbulent conditions can lead to the film growing by more than a factor of two compared to low turbulence conditions. If surface films adopt an ultra-viscous state with bulk diffusion coefficients of less than 10^-18  cm² s^-1 , a significant decrease in film growth is expected. The presence of chemical reactions in the film has the potential to increase the rate of film growth by nearly a factor of two.

Spatial and temporal scales of variability for indoor air constituents

Historically air constituents have been assumed to be well mixed in indoor environments, with single point measurements and box modeling representing a room or a house. Here we demonstrate that this fundamental assumption needs to be revisited through advanced model simulations and extensive measurements of bleach cleaning. We show that inorganic chlorinated products, such as hypochlorous acid and chloramines generated via multiphase reactions, exhibit spatial and vertical concentration gradients in a room, with short-lived ⋅OH radicals confined to sunlit zones, close to windows. Spatial and temporal scales of indoor constituents are modulated by rates of chemical reactions, surface interactions and building ventilation, providing critical insights for better assessments of human exposure to hazardous pollutants, as well as the transport of indoor chemicals outdoors.

Evaluating Indoor Air Chemical Diversity, Indoor-to-Outdoor Emissions, and Surface Reservoirs Using High-Resolution Mass Spectrometry

Detailed offline speciation of gas- and particle-phase organic compounds was conducted using gas/liquid chromatography with traditional and high-resolution mass spectrometers in a hybrid targeted/nontargeted analysis. Observations were focused on an unoccupied home and were compared to two other indoor sites. Observed gas-phase organic compounds span the volatile to semivolatile range, while functionalized organic aerosols extend from intermediate volatility to ultra-low volatility, including a mix of oxygen, nitrogen, and sulfur-containing species. Total gas-phase abundances of hydrocarbon and oxygenated gas-phase complex mixtures were elevated indoors and strongly correlated in the unoccupied home. While gas-phase concentrations of individual compounds generally decreased slightly with greater ventilation, their elevated ratios relative to controlled emissions of tracer species suggest that the dilution of gas-phase concentrations increases off-gassing from surfaces and other indoor reservoirs, with volatility-dependent responses to dynamically changing environmental factors. Indoor-outdoor emissions of gas-phase intermediate-volatility/semivolatile organic hydrocarbons from the unoccupied home averaged 6-11 mg h^-1, doubling with ventilation. While the largest single-compound emissions observed were furfural (61-275 mg h^-1) and acetic acid, observations spanned a wide range of individual volatile chemical products (e.g., terpenoids, glycol ethers, phthalates, other oxygenates), highlighting the abundance of long-lived reservoirs resulting from prior indoor use or materials, and their gradual transport outdoors.

Observing ozone chemistry in an occupied residence

Outdoor ozone transported indoors initiates oxidative chemistry, forming volatile organic products. The influence of ozone chemistry on indoor air composition has not been directly quantified in normally occupied residences. Here, we explore indoor ozone chemistry in a house in California with two adult inhabitants. We utilize space- and time-resolved measurements of ozone and volatile organic compounds (VOCs) acquired over an 8-wk summer campaign. Despite overall low indoor ozone concentrations (mean value of 4.3 ppb) and a relatively low indoor ozone decay constant (1.3 h^-1), we identified multiple VOCs exhibiting clear contributions from ozone-initiated chemistry indoors. These chemicals include 6-methyl-5-hepten-2-one (6-MHO), 4-oxopentanal (4-OPA), nonenal, and C8-C12 saturated aldehydes, which are among the commonly reported products from laboratory studies of ozone interactions with indoor surfaces and with human skin lipids. These VOCs together accounted for ≥12% molecular yield with respect to house-wide consumed ozone, with the highest net product yield for nonanal (≥3.5%), followed by 6-MHO (2.7%) and 4-OPA (2.6%). Although 6-MHO and 4-OPA are prominent ozonolysis products of skin lipids (specifically squalene), ozone reaction with the body envelopes of the two occupants in this house are insufficient to explain the observed yields. Relatedly, we observed that ozone-driven chemistry continued to produce 6-MHO and 4-OPA even after the occupants had been away from the house for 5 d. These observations provide evidence that skin lipids transferred to indoor surfaces made substantial contributions to ozone reactivity in the studied house.

Polycyclic aromatic hydrocarbon contamination along roads based on levels on vehicle window films

Vehicular emissions are known to be major contributors of airborne polycyclic aromatic hydrocarbons (PAHs) in cities. In order to assess the long-term contamination of PAHs along roads, we collected organic films from vehicle windows (26 private cars and 4 buses, in Shanghai, China) and used mathematical models to convert the film-bound PAH concentrations to the airborne PAH concentrations. The field measurements of airborne PAHs revealed that the partitioning and Level III fugacity model was suitable to estimate the airborne concentrations of high and low volatile PAHs (expect for naphthalene), respectively. The total airborne PAH concentrations along roads in Shanghai ranged from 0.83 to 3.37 μg m^-3 and the incremental lifetime cancer risks (ILCR_total) by exposure to PAHs along roads were greater than the USEPA lower guideline of 10^-6, indicating non-negligible carcinogenic risks to drivers and passengers, especially via ingestion processes. This study provided a practicable method to investigate long-term air contamination of PAHs in vehicles and along roads based on film-bound PAH on vehicle windows. In addition, it was also possible to investigate the health risk in vehicles as a result of exposure to PAHs. Comparisons of PAHs between roads and shipping lanes also facilitated the delineation of vehicular and shipping PAH inventories. A capsule that summarizes the main finding of the work: Investigating film-bound PAH on vehicle windows is a practicable pathway to investigate the long-term contamination of PAHs in vehicles and along roads. This method can not only simplify the sampling processes, but the model calculations. The results also enabled investigations into ILCR in vehicles and specified source apportionment of traffic PAHs.