Transformation of CuO Nanoparticles in the Aquatic Environment: Influence of pH, Electrolytes and Natural Organic Matter

The role of rice husk in Oreochromis niloticus safety enhancement by bio-adsorbing copper oxide nanoparticles following its green synthesis: an endeavor to advance environmental sustainability

Lowering nanoparticles (NPs) toxicity before discharge into aquatic environments and employing agricultural waste materials for environmental sustainability are necessary nowadays. Since this has never been done, this work examines how green CuO NPs treated with rice husk (RH) as a bio-adsorbent may be safer for Nile tilapia (Oreochromis niloticus) than chemically manufactured ones. So, five groups of fish were randomly placed in glass aquaria. One group was a control, and four groups received 50 mg/L green and chemically produced CuO NPs (GS and CS) with and without RH for 24, 48, and 96 h. RH was collected from all groups, and the results showed GS-CuO NPs had a greater adsorptive capacity than CS-CuO NPs after all time intervals. After analyzing fish indicators in all groups compared to the control, higher Cu bioaccumulation was exhibited in the liver and gills. The liver and gills showed elevated levels of glutathione peroxidase (GPx), catalase (CAT), and thiobarbituric acid reactive substances (TBARS), while the levels of glutathione reduced (GSH) were significantly lower. In addition, Cu exposure impaired liver and gill histology. Finally, our results indicated that using RH as an adsorbent for CuO NPs after their green synthesis instead of chemical synthesis before they enter the aquatic environment can enhance the overall health of fish and environmental sustainability.

Location-dependent occurrence and distribution of metal-based nanoparticles in bay environments

Metal-based nanoparticles (MNPs) are increasingly being released into the marine environment, posing potential environmental risks. However, factors governing the environmental occurrence and distribution of MNPs in bays still lack a comprehensive understanding. Herein, we collected seawater and sediment samples from two adjacent bays (Daya Bay and Honghai Bay, which have similar water qualities), and determined the particle concentrations and sizes of multi-element MNPs (Ti-, Cu-, Zn-, Ag-, Mn-, Pb- and Cr-based NPs) via single particle inductively coupled plasma-mass spectrometry (spICP-MS). The internal circulation in Daya Bay has resulted in an even distribution of MNPs' particle concentrations and sizes in both seawater and sediments, while the terrestrial discharge in Honghai Bay has led to a gradient-decreasing trend in MNPs' concentrations from nearshore to offshore. Moreover, the relatively high abundance of MNPs in Honghai Bay has contributed to 2.35-fold higher environmental risks than Daya Bay. Overall, this study has provided solid evidence on the critical but overlooked factors that have shaped the occurrence and distribution of MNPs, providing new insights for risk management and emission regulation.

Recent advances on environmental behavior of Cu-based nanomaterials in soil-plant system: A review

In recent years, copper-based nanomaterials (Cu-based NMs) have shown great potential in promoting agriculture development due to their special physicochemical characteristics. With the mass production and overuse of Cu-based NMs, there are potential effects on the soil-plant environment. Soil organisms, especially soil microorganisms, play a significant part in terrestrial or soil ecosystems; plants, as indirect organisms with soil-related Cu-based NMs, may affect human health through plant agricultural products. Understanding the accumulation and transformation of Cu-based NMs in soil-plant systems, as well as their ecotoxicological effects and potential mechanisms, is a prerequisite for the scientific assessment of environmental risks and safe application. Therefore, based on the current literature, this review: (i) introduces the accumulation and transformation behaviors of Cu-based NMs in soil and plant systems; (ii) focuses on the ecotoxicological effects of Cu-based NMs on a variety of organisms (microorganisms, invertebrates, and plants); (iii) reveals their corresponding toxicity mechanisms. It appears from studies hitherto made that both Cu-based NMs and released Cu2+ may be the main reasons for toxicity. When Cu-based NMs enter the soil-plant environment, their intrinsic physicochemical properties, along with various environmental factors, could also affect their transport, transformation, and biotoxicity. Therefore, we should push for intensifying the multi-approach research that focuses on the behaviors of Cu-based NMs in terrestrial exposure environments, and mitigates their toxicity to ensure the promotion of Cu-based NMs.

Ecotoxicity and trophic transfer of metallic nanomaterials in aquatic ecosystems

Metallic nanomaterials (MNMs) possess unique properties that have led to their widespread application in fields such as electronics and medicine. However, concerns about their interactions with environmental factors and potential toxicity to aquatic life have emerged. There is growing evidence suggesting MNMs can have detrimental effects on aquatic ecosystems, and are potential for bioaccumulation and biomagnification in the food chain, posing risks to higher trophic levels and potentially humans. While many studies have focused on the general ecotoxicity of MNMs, fewer have delved into their trophic transfer within aquatic food chains. This review highlights the ecotoxicological effects of MNMs on aquatic systems via waterborne exposure or dietary exposure, emphasizing their accumulation and transformation across the food web. Biomagnification factor (BMF), the ratio of the contaminant concentration in predator to that in prey, was used to evaluate the biomagnification due to the complex nature of aquatic food chains. However, most current studies have BMF values of less than 1 indicating no biomagnification. Factors influencing MNM toxicity in aquatic environments include nanomaterial properties, ion variations, light, dissolved oxygen, and pH. The multifaceted interactions of these variables with MNM toxicity remain to be fully elucidated. We conclude with recommendations for future research directions to mitigate the adverse effects of MNMs in aquatic ecosystems and advocate for a cautious approach to the production and application of MNMs.

Design, fabrication, and evaluation of keratin and pectin incorporated supramolecular structured zero-oxidation state selenium nanogel blended 3D printed transdermal patch

This study investigates the synthesis of selenium nanoparticles (SeNPs), owing to the low cost and abundance of selenium. However, the toxicity of SeNP prompts the development of a selenium nanocomposite (SeNC) containing pectin, keratin, and ferulic acid to improve the bioactivity of Se[0]. Further, incorporating the SeNC in a suitable formulation for drug delivery as a transdermal patch was worth studying. Accordingly, various analytical techniques were used to characterize the SeNPs and the SeNC, confirming successful synthesis and encapsulation. The SeNC exhibited notable particle size of 448.2 ± 50.2 nm, high encapsulation efficiency (98.90 % ± 2.4 %), 28.1 ± 0.45 drug loading, and sustained drug release at pH 5.5. Zeta potential and XPS confirmed the zero-oxidation state. The supramolecular structure was evident from spectral analysis endorsing the semi-crystalline nature of the SeNC and SEM images showcasing flower-shaped structures. Further, the SeNC demonstrated sustained drug release (approx. 22 % at 48 h) and wound-healing potential in L929 fibroblast cells. Subsequently, the SeNC loaded into a gelling agent exhibited shear thinning properties and improved drug release by nearly 58 %. A 3D printed reservoir-type transdermal patch was developed utilizing the SeNC-loaded gel, surpassing commercially available patches in characteristics such as % moisture uptake, tensile strength, and hydrophobicity. The patch, evaluated through permeation studies and CAM assay, exhibited controlled drug release and angiogenic properties for enhanced wound healing. The study concludes that this patch can serve as a smart dressing with tailored functionality for different wound stages, offering a promising novel drug delivery system for wound healing.

Impact of nCuO containing treated wastewater on soil microbes and dissolved organic matter in paddy field leachate

Using treated wastewater (TWW) resources in agriculture is a major pathway for disseminating nanoparticles. Copper-oxide nanoparticles (nCuO) offer potential benefits, but their presence in the environment poses risks to agricultural and environmental sustainability. This study examined soil microbial transformations and the composition of leachate dissolved organic matter (DOM) of paddy soils irrigated with nCuO-contaminated TWW at different concentrations (T2: 0.02 mgL-1, T3: 0.2 mgL-1, T4: 2.0 mgL-1) and examined the differences in Cu source (T5: 0.2 mgL-1 CuSO4). Results showed negative impacts on the absolute microbial abundance with up to 46 % reduction relative to the control treatment (T1). Changes in relative abundance of specific microbes at the genus level deviated from the corresponding phyla. Acidobacteria, Actinobacteria, Chloroflexi, and Verrucomicrobia phyla increased in the surface (0-3 cm) and subsurface (3-15 cm) layers responding differently to nCuO. In the 0-3 cm layer, Nitrospirae, Euryarchaeota, and Crenarchaeota increased, but only Dechloromonas genus from Proteobacteria increased with increasing nCuO. No significant variations were observed in the DOM composition, except in T4, which had a significantly low content of dissolved organic carbon (DOC), total dissolved nitrogen, and terrestrial humic-like and protein-like components. Ninety-eight distinct genera were identified, of which 44%, including 15 bacteria and two archaea, varied between the surface and subsurface, among treatments, and significantly correlated with more DOM parameters in the subsurface. T4 had the highest microbial diversity in the 0-3 layer, and Cu treatments slightly increased the diversity index in the subsurface. Moreover, the effects differed by Cu source, with T3 showing 10 % more reduction in the subsurface and 17 % less reduction in the surface than T5. The variable microbial responses to nCuO and their strong correlations with DOM highlight the need to consider the potential consequences of low nCuO concentrations on biogeochemical cycles.

Dissolution kinetics of copper oxide nanoparticles in presence of glyphosate

Recently CuO nanoparticles (n-CuO) have been proposed as an alternative method to deliver a Cu-based pesticide for controlling fungal infestations. With the concomitant use of glyphosate as an herbicide, the interactions between n-CuO and this strong ligand need to be assessed. We investigated the dissolution kinetics of n-CuO and bulk-CuO (b-CuO) particles in the presence of a commercial glyphosate product and compared it to oxalate, a natural ligand present in soil water. We performed experiments at concentration levels representative of the conditions under which n-CuO and glyphosate would be used (∼0.9 mg/L n-CuO and 50 μM of glyphosate). As tenorite (CuO) dissolution kinetics are known to be surface controlled, we determined that at pH 6.5, T ∼ 20 °C, using KNO3 as background electrolyte, the presence of glyphosate leads to a dissolution rate of 9.3 ± 0.7 ×10-3 h-1. In contrast, in absence of glyphosate, and under the same conditions, it is 2 orders of magnitude less: 8.9 ± 3.6 ×10-5 h-1. In a more complex multi-electrolyte aqueous solution the same effect is observed; glyphosate promotes the dissolution rates of n-CuO and b-CuO within the first 10 h of reaction by a factor of ∼2 to ∼15. In the simple KNO3 electrolyte, oxalate leads to dissolution rates of CuO about two times faster than glyphosate. However, the kinetic rates within the first 10 h of reaction are about the same for the two ligands when the reaction takes place in the multi-electrolyte solution as oxalate is mostly bound to Ca2+ and Mg2+.

Synthetic graphene-copper nanocomposites interact with the hACE-2 enzyme and inhibit its biochemical activity

This study demonstrates the copper nanocomposite-induced enzymatic inhibition of human angiotensin I-converting enzyme-2 (hACE-2) by complex stabilization through the formation of the enzyme nanocomposite. The immediate application of this work is related to ACE-2 as a mechanism of SARS-CoV-2 entry into cells. Moreover, ACE-2 enzyme regulation is a potential therapeutic strategy in hypertension and cardiovascular disease, diabetes, lung injury, and fibrotic disorders. Thus, inhibition of ACE-2 with nanocomposite therapy, may have pharmacologic application with regard to infectious and non-infectious diseases. Synthesized copper nanocomposites described here alone with a commercially available compound, were tested for their potential to inhibit hACE-2 activities. Following wet chemical synthesis, Cu/CuO nanoparticles and graphene-copper (GO-Cu) complexes were synthesized and characterized for their chemical integrity. Cu/CuO formed well-dispersed clusters of 390 ± 100 nm, that when complexed with the hACE-2 enzyme exhibited larger clusters of 506 ± 56 nm. The formation of the Cu/CuO and hACE-2 enzyme complex was monitored by analyzing the zeta potential, which reflected the surface charge distribution of the complex. A negatively charged Cu/CuO nanocomposite nearly becomes neutral when complexed with hACE-2 further assuring the complex formation. Formation of this complex and its inactivation of hACE-2 was evaluated using a standardized protocal for enzymatic activity. Similarly, carboxylate-functionalized graphene was complexed with copper, and its inhibitory effect was studied. Each step in the GO-Cu composite formation was monitored by characterizing its surface electrical properties, resulting in a decrease in its zeta potential and conductivity when complexed with copper. The interaction of the nanocomposites with hACE-2 was confirmed by 2D-FDS and gel electrophoresis analysis. GO-Cu was a rapid and efficacious inhibitor compared to Cu-CuO, especially at lower concentrations (2 μg ml-1). Considering the environmental friendliness of copper and graphene and their use in industries as surface coating materials, we anticipate that use of these composites once proven effective, may have future antimicrobial application. Utility of nanocomposites as antimicrobials, either as a surface antimicrobial or as an in vivo therapeutic, could be invisioned for use against current unknown and/or emergent pathogens.

Converting Nanotoxicity Data to Information Using Artificial Intelligence and Simulation

Decades of nanotoxicology research have generated extensive and diverse data sets. However, data is not equal to information. The question is how to extract critical information buried in vast data streams. Here we show that artificial intelligence (AI) and molecular simulation play key roles in transforming nanotoxicity data into critical information, i.e., constructing the quantitative nanostructure (physicochemical properties)-toxicity relationships, and elucidating the toxicity-related molecular mechanisms. For AI and molecular simulation to realize their full impacts in this mission, several obstacles must be overcome. These include the paucity of high-quality nanomaterials (NMs) and standardized nanotoxicity data, the lack of model-friendly databases, the scarcity of specific and universal nanodescriptors, and the inability to simulate NMs at realistic spatial and temporal scales. This review provides a comprehensive and representative, but not exhaustive, summary of the current capability gaps and tools required to fill these formidable gaps. Specifically, we discuss the applications of AI and molecular simulation, which can address the large-scale data challenge for nanotoxicology research. The need for model-friendly nanotoxicity databases, powerful nanodescriptors, new modeling approaches, molecular mechanism analysis, and design of the next-generation NMs are also critically discussed. Finally, we provide a perspective on future trends and challenges.

Metallic Nanosystems in the Development of Antimicrobial Strategies with High Antimicrobial Activity and High Biocompatibility

Antimicrobial resistance is a major and growing global problem and new approaches to combat infections caused by antibiotic resistant bacterial strains are needed. In recent years, increasing attention has been paid to nanomedicine, which has great potential in the development of controlled systems for delivering drugs to specific sites and targeting specific cells, such as pathogenic microbes. There is continued interest in metallic nanoparticles and nanosystems based on metallic nanoparticles containing antimicrobial agents attached to their surface (core shell nanosystems), which offer unique properties, such as the ability to overcome microbial resistance, enhancing antimicrobial activity against both planktonic and biofilm embedded microorganisms, reducing cell toxicity and the possibility of reducing the dosage of antimicrobials. The current review presents the synergistic interactions within metallic nanoparticles by functionalizing their surface with appropriate agents, defining the core structure of metallic nanoparticles and their use in combination therapy to fight infections. Various approaches to modulate the biocompatibility of metallic nanoparticles to control their toxicity in future medical applications are also discussed, as well as their ability to induce resistance and their effects on the host microbiome.

Internalization of the Metal-Organic Framework MIL-101(Cr)-NH2 by a Freshwater Alga and Transfer to Zooplankton

The common metal-organic framework (MOF) MIL-101(Cr)-NH₂ has attracted considerable attention due to its great potential applications in the environmental field. Nevertheless, its behavior and fate in aquatic systems are unknown. This study quantified and visualized the interactions of MIL-101(Cr)-NH₂ with the freshwater phytoplanktonic alga Chlamydomonas reinhardtii and its potential trophic transfer to zooplankton. The unicellular alga absorbed and accumulated the MOF by surface attachment, forming agglomerates and eventually cosettling out from water. Bioimaging revealed that MIL-101(Cr)-NH₂ was internalized by the algal cells and mainly occurred in the pyrenoid. Without algae in a freshwater system, MIL-101(Cr)-NH₂ was ingested by Daphnia magna, showing steadily increasing concentrations approaching 1-9% of dry body weight. Addition of algae substantially suppressed D. magna uptake of MIL-101(Cr)-NH₂ by 63.8-97.9%. Such inhibition could be explained by the competitive uptake of MOF by the algae and the inductive effects of algal food on MOF elimination by D. magna. The MOF (≤1 mg/L) ingested by D. magna was centered in the gut regions, whereas large MOF or algae-MOF aggregates were adsorbed onto the carapace and appendages, including the antennae, at 10 mg/L. Overall, the algae were the major targets for MIL-101(Cr)-NH₂, with nearly all algal cells settling out at 10 mg/L within 24 h. The possibility of trophic transfer of MIL-101(Cr)-NH₂ to D. magna in aquatic systems with algae present was limited due to its low accumulation potential and short retention time in D. magna.

Environmental Implications Associated with the Development of Nanotechnology: From Synthesis to Disposal

Nanotechnology remains under continuous development. The unique, fascinating, and tunable properties of nanomaterials make them interesting for diverse applications in different fields such as medicine, agriculture, and remediation. However, knowledge about the risks associated with nanomaterials is still poorly known and presents variable results. Furthermore, the interaction of nanomaterials with biological systems and the environment still needs to be clarified. Moreover, some issues such as toxicity, bioaccumulation, and physicochemical transformations are found to be dependent on several factors such as size, capping agent, and shape, making the comparisons even more complex. This review presents a comprehensive discussion about the consequences of the use and development of nanomaterials regarding their potential risks to the environment as well as human and animal health. For this purpose, we reviewed the entire production chain from manufacturing, product development, applications, and even product disposal to raise the important implications at each stage. In addition, we present the recent developments in terms of risk management and the recycling of nanomaterials. Furthermore, the advances and limitations in the legislation and characterization of nanomaterials are also discussed.

Impact of nanoplastic debris on the stability and transport of metal oxide nanoparticles: role of varying soil solution chemistry

The release of metal-based nanoparticles (MNPs) and nanoplastic debris (NPDs) has become ubiquitous in the natural ecosystem. Interaction between MNPs and NPDs may alter their fate and transport in the sub-surface environment and have not been addressed so far. Therefore, the present study has explored the role of NPDs on the stability and mobility of extensively used MNPs, i.e., CuO nanoparticles (NPs) under varying soil solutions (SS) chemistry. In the absence of NPDs, a very high aggregation of CuO NPs observed in SS extracted from black, lateritic, and red soils, which can be correlated with ionic strength (IS) and type of ionic species. The sedimentation rate (k_sed(1/h)) for CuO NPs was >0.5 h^-1 in the case of these SS. Interestingly, the stability and sedimentation behavior of CuO NPs varied significantly in the presence of NPDs. The k_sed for CuO NPs decreased to half and found <0.25 h^-1 in the presence of NPDs in all SS. C/C₀ values in breakthrough curves increased drastically (black < alluvial < laterite < red) in presence of NPDs. Results suggest that the release of NPDs in the terrestrial ecosystem is a potential threat leading to increased mobility of MNPs in the environment.

Stability, aggregation, and sedimentation behaviors of typical nano metal oxide particles in aqueous environment

The wide use of nano metal oxide particles (NMOPs) brings about their inevitable release into the water environment, affecting the environment and human health. Therefore, the stability, aggregation, and sedimentation process of four typical NMOPs (ZnO NPs, CeO₂ NPs, TiO₂ NPs, and CuO NPs) were investigated in artificial water and real municipal sewage to reveal their complicated behavior. Results showed that NMOPs aggregated at the pH of zero-charge point, and their hydrodynamic diameters and aggregation rates could reach the maximum values. The hydrodynamic diameters and aggregation rates of ZnO NPs, CeO₂ NPs, TiO₂ NPs, and CuO NPs at the zero-charge point were 617, 1760, 870, 1502 nm, and 31.7, 1158.1, 48.3, 115.7 nm/min, respectively. In addition, the dissolution of NMOPs led to the sedimentation rates under acidic conditions being much lower than those under neutral and alkaline conditions. The aggregation and sedimentation performance of NMOPs were affected by not only pH but also ionic strength (IS) and species. The aggregation rates of NMOPs increased with the increase of IS (0-10 mM), and the maximum aggregation rate of CeO₂ NPs was 470.1 nm/min (pH = 7 and CaCl₂ = 10 mM). According to Coulomb's law, divalent cations (Mg²⁺, Ca²⁺) were more competitively adsorbed on the surface of NMOPs than monovalent cations (K⁺, Na⁺), which increased the zeta potential and aggregation rate of NMOPs. Furthermore, the NMOPs were easier to aggregate in municipal sewage because of the homogeneous aggregation between nanoparticles and heterogeneous aggregation with natural colloids. The total interaction energy between NMOPs was calculated by the classical Derjaguin-Landau-Verwey-Overbeek (DLVO) theoretical formula, which was consistent with the experimental results.

Synthesis of CuO nanoparticles stabilized with gelatin for potential use in food packaging applications

In the present study, a method for the synthesis of gelatin-stabilized copper oxide nanoparticles was developed. Synthesis was carried out by direct chemical precipitation. Copper sulfate, chloride, and acetate were used as precursors for the copper oxide synthesis. Gelatin was used as a stabilizer. It was found that the formation of monophase copper oxide II only occurred when copper acetate was used as a precursor. Our results showed that particles of the smallest diameter are formed in an aqueous medium (18 ± 6 nm), and those of th largest diameter—in an isobutanol medium (370 ± 131 nm). According to the photon correlation spectroscopy data, copper oxide nanoparticles synthesized in an aqueous medium were highly stable and had a monomodal size distribution with an average hydrodynamic radius of 61 nm. The study of the pH effect on the colloidal stability of copper oxide nanoparticles showed that the sample was stable in the pH range of 6.8 to 11.98. A possible mechanism for the pH influence on the stability of copper oxide nanoparticles is described. The effect of the ionic strength of the solution on the stability of the CuO nanoparticles sol was also studied, and the results showed that Ca²⁺ ions had the greatest effect on the sample stability. IR spectroscopy showed that the interaction of CuO nanoparticles with gelatin occurred through the hydroxyl group. It was found that CuO nanoparticles stabilized with gelatin have a fungicidal activity at concentration equivalent 2.5 · 10⁻³ mol/L and as a material for food nanopackaging can provide an increase in the shelf life of products on the example of strawberries and tomatoes. We investigated the possibility of using methylcellulose films modified with CuO nanoparticles for packaging and storage of hard cheese “Holland”. The distribution of CuO nanoparticles in the methylcellulose film was uniform. We found that methylcellulose films modified with CuO nanoparticles inhibited the growth and development of QMAFAM, coliforms, yeast and mold in experimental cheese sa mples. Our research has shown that during the cheese storage in thermostat at 35 ± 1 °C for 7 days, CuO nanoparticles migrated to the product from the film. Nevertheless, it is worth noting that the maximum change in the concentration of copper in the experimental samples was only 0.12 µg/mg, which is not a toxic concentration. In general, the small value of migration of CuO nanoparticles confirms the high stability of the developed preparation. Our results indicated that the CuO nanoparticles stabilized with gelatin have a high potential for use in food packaging – both as an independent nanofilm and as part of other packaging materials.

Copper II oxide nanoparticles (CuONPs) alter metabolic markers and swimming activity in zebra-fish (Danio rerio)

The present study aimed to compare the metabolic effects caused by using copper oxide nanoparticles with two distinct morphologies nanorods and nanosphere. The CuONPs in the form of nanorods were characterized in the order of 500 nm, on a scale of 20, 100, and 500 nm. Meanwhile, the nanosphere CuONPs were characterized in the order of 5 nm, on a 30 nm scale. The analysis of metabolic rate was performed using the closed respirometry technique, specific ammonia excretion, and swimming ability as biomarkers, the physiological effects on Danio rerio were investigated. For the experiments, 88 fish were used, exposed for 24 h at concentrations of 0, 50, 100, and 200 μg/L of copper oxide nanoparticles in the form of nanospheres and nanorods, respectively. The tests carried out with the nanorods demonstrated metabolic alterations in fish, with an increase of 294% and 321% in the metabolic rate at concentrations of 100 μg/L and 200 μg/L, respectively. Furthermore, there was a decrease in specific ammonia excretion by 34% and 83% and in swimming capacity by 34% and 55% at concentrations of 100 and 200 μg/L, respectively, when compared to the control. The tests performed with nanospheres did not show significant changes compared to the control. These experiments showed that different morphological structures of the same copper oxide nanoparticle caused different effects on fish metabolism. It is concluded that the characterization of nanoparticles is essential to understand their effects on fish, since their structural forms can cause different toxic effects on D. rerio.

Influence of nano and bulk copper on agile frog development

Nanotechnology, as one of the fastest-growing industries, offers many benefits in various fields. However, properties that contribute to its positive effects, in other context, can cause adverse effects to various organisms, such as amphibians. Identifying possible negative effects on its survival is crucial since amphibians are the most threatened group of vertebrates. In that context, we investigated the influence of both nano and bulk copper on embryonic development of agile frog, Rana dalmatina. The embryos were exposed to various concentrations (0.01 mg/L, 0.075 mg/L, 0.15 mg/L or 0.3 mg/L) of either nano (CuO, declared size 40-80 nm) or bulk form (CuSO₄·5H₂O) for 16 days. Upon the experiment, tadpoles were measured and weighted, then homogenized and their protein, lipid, and carbohydrates content determined, as well as the activity of LDH. Our results suggest stronger negative influence of nano copper to size and weight of tadpoles, and bulk copper on lipid content, while both had strong negative effect on carbohydrates content, and LDH activity. In addition, our results suggest agile frog to be more susceptible to negative influence of both, nano and bulk copper, than commonly used Xenopus laevis.

Cutting-edge spectroscopy techniques highlight toxicity mechanisms of copper oxide nanoparticles in the aquatic plant Myriophyllum spicatum

Copper oxide nanoparticles (CuO-NPs) have been increasingly released in aquatic ecosystems over the past decades as they are used in many applications. Cu toxicity to different organisms has already been highlighted in the literature, however toxicity mechanisms of the nanoparticulate form remain unclear. Here, we investigated the effect, transfer and localization of CuO-NPs compared to Cu salt on the aquatic plant Myriophyllum spicatum, an ecotoxicological model species with a pivotal role in freshwater ecosystems, to establish a clear mode of action. Plants were exposed to 0.5 mg/L Cu salt, 5 and 70 mg/L CuO-NPs during 96 h and 10 days. Several morphological and physiological endpoints were measured. Cu salt was found more toxic than CuO-NPs to plants based on all the measured endpoints despite a similar internal Cu concentration demonstrated via Cu mapping by micro particle-induced X-ray emission (μPIXE) coupled to Rutherford backscattering spectroscopy (RBS). Biomacromolecule composition investigated by FTIR converged between 70 mg/L CuO-NPs and Cu salt treatments after 10 days. This demonstrates that the difference of toxicity comes from a sudden massive Cu²⁺ addition from Cu salt similar to an acute exposure, versus a progressive leaching of Cu²⁺ from CuO-NPs representing a chronic exposure. Understanding NP toxicity mechanisms can help in the future conception of safer by design NPs and thus diminishing their impact on both the environment and humans.

Transformation of copper oxide nanoparticles as affected by ionic strength and its effects on the toxicity and bioaccumulation of copper in zebrafish embryo

This study aimed to investigate the transformation of copper oxide nanoparticles (CuO NPs) in aquatic environments under different ionic strength and further examine its effects on copper toxicity and bioaccumulation by monitoring the responses and uptake behaviours of zebrafish embryo. Ionic strength (IS) was simulated according to surface water (1.5 mM), groundwater (15 mM), and wastewater (54 mM), representing low-, mid-, and high-IS water, respectively. At the highest exposure of 10 mg CuO/L, zebrafish larvae mortality was increased from 21.3% to 33.3%, when IS decreased from 54 to 1.5 mM. Low-IS solution also caused the highest numbers of delayed hatching embryo (81.3%) and opaque yolk deformation (36.3%). Copper bioaccumulation markedly increased when larvae were exposed to low-IS water (35%) relative to high-IS water (15%). Exposing to low-IS particularly enhanced copper uptake (~15 ng Cu/g inside embryo), facilitating the copper accumulation in the heart of larvae, whereas aggregated CuO NPs (>500 nm) in mid- and high-IS water were blocked from the embryo and found abundantly in the body axis and tail. Results indicate that CuO NPs in low-IS solutions rapidly form the relatively small CuO NP aggregates with a high copper dissolution, which would pose great concern for aquatic organisms.

The severe toxicity of CuO nanoparticles to the photosynthesis of the prokaryotic algae Arthrospira sp

This research first verified that prokaryotic algae are more sensitive to toxicity of CuO nanoparticles (CuO NPs) than eukaryotic algae and that CuO NPs damaged photosynthesis of prokaryotic algae (Arthrospira sp.) but had no effect on respiration. The Cu²⁺ released by CuO NPs caused a bending deformation of the thylakoid, which was an important cause of the decline in photosynthetic capacity. In addition, the D1 protein was the most susceptible site to CuO NPs. The degradation of D1 protein reduced photosynthetic electron transport, which enhanced the excess excitation energy to cause the accumulation of reactive oxygen species (ROS) to further result in oxidative stress on algae. Dissolved organic matter (DOM) increased the toxicity of CuO NPs to photosynthesis of Arthrospira sp. The damage of photosynthesis caused by CuO NPs is an important reason why CuO NPs have a serious toxicity to algae.

Removal of Tannic Acid Stabilizes CuO Nanoparticles from Aqueous Media by PAFC: Effect of Process Conditions and Water Chemistry

The increased utilization of CuO nanoparticles (CuO NPs) in various fields has raised concerns about their discharge into water containing a wide range of organic ligands. Moreover, the adsorption of these ligands can stabilize the CuO NPs in drinking water treatment plants. Thus, their removal from potable water is important to mitigate the risk to humans. The present study explored the efficacy of the coagulation-sedimentation (C/S) process for the removal of tannic acid (TA)-stabilized CuO NPs using polyaluminum ferric chloride (PAFC) as a coagulant. Moreover, the influence of process conditions (stirring speed) and water chemistry (i.e., pH and ionic strength (IS)) were also investigated to determine their impact on removal. The results showed that stirring speed in the reaction phase significantly affected the removal due to increased flocculation compared with stirring speed in the mixing phase. In addition, pH and IS affect the colloidal stability and removal efficiency of CuO NPs. A relatively better removal performance (<99%) of CuO NPs was found at lower coagulant dosage in the pH range 6-8. The addition of organic ligands reversed the surface charge potential and enhanced the colloidal stability of CuO NPs, resulting in the destabilization of TA-CuO NPs, thereby reducing the optimum PAFC dosage for removal. By contrast, the IS above the critical coagulation concentration decreased the removal efficiency due to inhibition of the ionic activity of PAFC hydrolysate in the aqueous environment. Fourier transform infrared findings of TA-CuO NPs composite flocs suggest that the primary removal mechanism might be mediated via the combined effect of neutralization, complexation as well as adsorption.

Glycerol Valorization over ZrO2-Supported Copper Nanoparticles Catalysts Prepared by Chemical Reduction Method

Copper nanoparticles (NPs) and ZrO2-supported copper NPs (Cu NPs/ZrO2) were synthesized via a chemical reduction method applying different pH (4, 7 and 9) and evaluated in a glycerol dehydration reaction. Copper NPs were characterized with transmission electron microscopy (TEM) and UV–vis spectroscopy. Transmission electron microcopy (TEM) results revealed a homogeneous distribution of copper NPs. A hypsochromic shift was identified with UV–vis spectroscopy as the pH of the synthesis increased from pH = 4 to pH = 9. Zirconia-supported copper NPs catalysts were characterized using N2 physisorption, X-ray diffraction (XRD), TEM, X-ray photoelectron spectroscopy (XPS), temperature-programmed reduction (TPR), temperature-programmed desorption of ammonia (NH3-TPD) and N2O chemisorption. The presence of ZrO2 in the chemical reduction method confirmed the dispersion of the copper nanoparticles. X-ray diffraction indicated only the presence of tetragonal zirconia patterns in the catalysts. XPS identified the Cu/Zr surface atomic ratio of the catalysts. TPR patterns showed two main peaks for the Cu NPS/ZrO2 pH = 9 catalyst; the first peak between 125 and 180 °C (region I) was ascribed to more dispersed copper species, and the second one between 180 and 250 °C (region II) was assigned to bulk CuO. The catalysts prepared at pH = 4 and pH = 7 only revealed reduction at lower temperatures (region I). Copper dispersion was determined by N2O chemisorption. With NH3-TPD it was found that Cu NPs/ZrO2 pH = 9 exhibited the highest total quantity of acidic sites and the highest apparent kinetic constant, with a value of 0.004 min−1. The different pH applied to the synthesis media of the copper nanoparticles determined the resultant copper dispersion on the ZrO2 support, providing active domains for glycerol conversion.

Features of Bioaccumulation and Toxic Effects of Copper (II) Oxide Nanoparticles Under Repeated Oral Exposure in Rats

BACKGROUND

Currently, the range of copper (II) oxide nanoparticles' (CuO NPs) applications is expanding and the global production of CuO NPs is increasing. In this regard, the risk of exposure of the population to this nanomaterial increases.

OBJECTIVE

The aim of the study is to investigate the patterns of bioaccumulation and toxic effects of CuO NPs after multiple oral exposures.

METHODS

The particle size was determined by scanning electron microscopy and dynamic laser light scattering. Specific surface area was measured by the method of Brunauer, Emmett, Teller. Total pore volume - by the method of Barrett, Joyner, Khalenda. Twenty-four hours after the final exposure, blood samples were taken for biochemical and hematological analysis, and internal organs were taken to determine their mass, copper concentration and histological analysis. The study was carried out in comparison with copper (II) oxide microparticles (CuO MPs).

RESULTS

In terms of size, surface area, and pore volume, the studied copper (II) oxide sample is a nanomaterial. The median lethal dose of CuO NPs was 13187.5 mg/kg of body weight. Bioaccumulation occurs in the stomach, blood, intestines, liver, lungs, kidneys and brain. Pathomorphological changes in the liver are manifested in the form of necrosis, degeneration, hepatitis; kidney - proliferation of mesangial cells, dystrophy; stomach - gastritis; small intestine - hyperplasia, enteritis; large intestine - colitis; lungs - hyperplasia, abscess, pneumonia, bronchitis, vasculitis. Clumps of brown pigment were detected in the kidneys, stomach and lungs. The mass of the stomach and intestines increased, the mass of the liver, kidneys and lungs decreased. Pathomorphological changes in organs are likely to cause an increase in the levels of activity of alanine aminotransferase, aspartate aminotransferase, alkaline phosphatase, lactate dehydrogenase, amylase, malondialdehyde concentration and a decrease in plasma antioxidant activity. The proportion of segmented neutrophils, the number of leukocytes are raised, the proportion of lymphocytes is reduced.

CONCLUSION

The degree of bioaccumulation and toxicity of CuO NPs are more expressed in relation to CuO MPs.

Dissolution of copper oxide nanoparticles is controlled by soil solution pH, dissolved organic matter, and particle specific surface area

Dissolution is the primary process affecting the bioavailability and toxicity of nanoscale copper oxide (nano-CuO) to plants and soil organisms. In this study, particle morphology, organic acid, and soil properties were considered to understand the dissolution characteristics of nano-CuO in soil solutions. The results showed that the copper ions (Cu²⁺) released from spherical nano-CuO (CuO NPs), tubular nano-CuO (CuO NTs), and spherical microsized CuO (CuO MPs) in the ten soil solutions were 26.6-4194.0 μg/L, 4.90-217.1 μg/L, and 10.8-326.0 μg/L, respectively. The concentration of Cu²⁺ was negatively correlated with the pH of the soil solution and positively correlated with the contents of dissolved organic carbon (DOC), aluminum, and manganese. Multivariate stepwise regression analysis indicated that the dissolution of CuO NPs could be well predicted by pH and DOC contents of the soil solutions. In the GD soil solution (acidic), 4- and 8-fold of the DOC content amendments significantly promoted the dissolution of the three sizes of CuOs, resulting in an increase of Cu²⁺ 4.55-11.3 and 5.67-16.2 times, respectively. In the CQ soil solution (neutral), 8-fold DOC amendments increase the release of Cu²⁺ 2.13-16.6 times. While in the SD soil solution (alkaline), promoting effect on the dissolution was only observed for nano-CuOs, with Cu²⁺ elevated by factors of 1.56-4.64 and 1.38-4.48. The amendments of Al³⁺ and Mn²⁺ in soil solution increased the amounts of Cu²⁺ 1.13-4.80 and 1.02-1.46 times in the GD soil solution. In comparison, no significant promoting effects were observed in CQ and SD soil solutions due to their stronger buffering capacities. These findings offer insight into the dissolution behavior of nano-CuOs in soils and be helpful to evaluate their environmental risks.

Regulation mechanisms of humic acid on Pb stress in tea plant (Camellia sinensis L.)

Though the interaction between humic acid (HA) and heavy metals has been widely reported, the effects of HA on the toxicity of heavy metals to plants are still in debate. In this study, the regulation mechanisms of HA on Pb stress in tea plant (Camellia sinensis L.) was investigated through hydroponic experiments, and the experimental results were explained by using transmission electron microscope (TEM), scanning transmission X-ray microscopes (STXM) and isobaric tags for relative and absolute quantitation (iTRAQ) differential proteomics. Significant alleviation of Pb stress was found with HA coexistence. TEM results showed that HA greatly mitigated the damage of cells caused by Pb stress. Compared with sole Pb treatment, the addition of HA increased the contents of pectin and pectic acid in the cell wall by 10.5% and 30.5%, while arabinose (Ara) and galactose (Gal) decreased by 20.5% and 15.9%, respectively, which were beneficial for increasing Pb adsorption capacity of the cell wall and promoting cell elongation. Moreover, iTRAQ differential proteomics analysis proved that HA strengthened the antioxidant system, promoted the synthesis of cell wall, and stabilized protein and sulfur-containing substance metabolism in molecular level. Notably, the concentration of calcium (Ca) in the cell wall of HA coexistence treatment was 47.4% higher than Pb treatment. STXM results also indicated that the distribution of Ca in the cell wall was restored with the presence of HA. This might promote the formation of the egg-box model, thus alleviating Pb stress in cells. Our results reveal the regulation mechanisms of HA on Pb detoxification in plants and provide useful information for improving the safety of agricultural products.

Size-dependent cellular internalization and effects of polystyrene microplastics in microalgae P. helgolandica var. tsingtaoensis and S. quadricauda

Microplastics (MPs) are persistent contaminants in aquatic environments. Microalgae, as the main phytoplankton and primary producers, usually co-exist with MPs. Despite previous studies that have proved the interaction of MPs and microalgae, it is largely unknown whether MPs can be uptake into cells of microalgae. In this study, both marine P. helgolandica var. tsingtaoensis and freshwater microalgae S. quadricauda were respectively exposed to 10 mg/L polystyrene microbeads with five diameter sizes: 1.0, 2.0, 3.0, 4.0, and 5.0 μm. Confocal laser scanning and 3D image analysis showed that mean 24.0 % or 11.3 % cells of P. helgolandica var. tsingtaoensis contained 1.0 μm or 2.0 μm MPs after 72 h exposure. While mean 43.3 % or 15.3 % of S. quadricauda individuals engulfed 1.0 μm or 2.0 μm MPs within cells. But, none of 3.0-5.0 μm MPs were observed within algal cells. These results demonstrate the size-dependent cellular internalization of MPs in microalgae. Exposure to 1.0-2.0 μm PS MPs caused a significant reduction in the density of microalgae and influenced photosynthesis, which suggests cellular internalization of MPs can influence algal fertility and growth. This discovery first confirms cellular internalization of MPs in phytoplankton, of significance for the fate and eco-toxicity of MPs in the aquatic ecosystem.

Stability and characterization of mixture of three particle system containing ZnO-CuO nanoparticles and clay

The aim of this study was to understand heteroaggregation of mixture of ZnO and CuO nanoparticles (NPs) with clay, for the first time as per the authors' knowledge. Aggregation studies of mixture of ZnO and CuO nanoparticles with clay was done (ionic strength =5 mM; pH 7; nanoparticles concentration = 0.1 mg/L, 1 mg/L, 10 mg/L; Clay concentration = 1, 10, and 100 mg/L and HA concentration = 0.1,1, and 10 mg/L as total organic carbon). Critical coagulation concentration (CCC) and attachment efficiency values of suspensions with ZnO: CuO ratio = 0.1, 1, 10 were also determined. Aggregation and liquid portions of mixture suspension at equal mass ratio were characterized for size, zeta potential (ZP), metal and ion contents, pH and conductivity. Results indicated that CCC was found to be 120.7 mM for ZnO: CuO ratio 10 and 1144 mM for ZnO: CuO ratio 1. Values of attachment efficiency were obtained to be 0.9 and 0.8 for these two ZnO:CuO ratio. At natural water ionic strength (IS) condition, aggregate rate constant of mixture of particles ranged from 0.281 to 8.63 nm/min for 10 mg/L NP concentration. Aggregation in suspension containing mixture of particles was found to be affected by NP concentration, clay concentration, and humic acid (p < 0.05). During a 1-h aggregation study, 2.67 mg Cu metal/g aggregate and 0.38 mg Zn/g aggregate were found in aggregates of 5 mM suspension. Overall, this study provided information on aggregation characterization of mixture of metal oxide nanoparticles (ZnO and CuO) in HA and clay presence, which is useful in understanding aggregation formation and in characterizing exposure dose for environmental risk assessment. More detailed information on a three -particle system with natural colloids is required for predicting their fate in aquatic system and defining risk.

The aggregation and sedimentation of two different sized copper oxide nanoparticles in soil solutions: Dependence on pH and dissolved organic matter

Copper oxide nanoparticles (CuO NPs) in soil have received considerable attention because of their potential impact on the environment. In the present study, the stability of CuO NPs (50 nm and 80 nm) in eight soil solutions as well as the major influencing factors was investigated. The results showed that hetero-aggregation between natural colloids and NPs dominated the first stage of aggregation, afterwards the two different sized CuO NPs exhibited different aggregation behaviors. The aggregation of 80 nm CuO was inconspicuous except for notable aggregation observed in JX soil solution where the zeta potential of CuO NPs is close to zero. While for 50 nm CuO NPs, the aggregate size sharply decreased and the aggregates gradually reached a stable state. Further, the sedimentation rate and residual concentration of 50 nm CuO were found to be greater than those of 80 nm CuO. The residual amount of 80 nm CuO in the JX soil solution was lower than those in other soil solutions owing to the lowest zeta potential of the NPs. The pH of the soil solution has a significant effect on the stability of CuO NPs because of the shifting of the zeta potential of the NPs. In addition, dissolved organic carbon showed a statistically significant positive correlation with the residual concentration of CuO NPs. These findings imply the properties of CuO NPs as well as environmental factors including pH and DOC play key role in determining the fate, transport, and bioavailability of CuO NPs in soils.

Role of water chemistry on stability, aggregation, and dissolution of uncoated and carbon-coated copper nanoparticles

Intentional or accidental release of copper nanoparticles (Cu-NPs) from consumer products during manufacturing, use, and end-of-life management could pose health and ecological risks. This paper presents a detailed study on the role of water chemistry on the fate of uncoated and carbon-coated Cu-NPs dispersed in aqueous cetyltrimethylammonium bromide (CTAB) surfactant in the presence and absence of humic acids (HAs). A range of water chemistry and HAs had minimum impact on hydrodynamic diameter and zeta-potential values of uncoated and carbon-coated Cu-NPs. The water pH significantly (p < 0.001) affected the aggregation of uncoated Cu-NPs unlike that of carbon-coated Cu-NPs; however, the presence of HAs increased the stability of uncoated Cu-NPs. Although CTAB is considered as an efficient dispersant to stabilize Cu-NPs, the effect descended with time for uncoated Cu-NPs. The dissolution of Cu over time decreased with increasing pH for both uncoated (0.5-50% weight) and carbon-coated (0.5-40% weight) Cu-NPs. However, carbon-coated Cu-NPs exhibited significant dissolution (p < 0.001) at neutral pH than uncoated Cu-NPs may be due to the additional carbon it acquired during coating. Increasing HAs concentration from 0 to 15 mg L^-1 at pH 5.5 inhibited aggregations but enhanced dissolution of the uncoated and carbon-coated Cu-NPs. These findings inform risk analysis of Cu-NPs including how Cu-NPs fate, mobility and bioavailability are modulated by particles coating and dispersant, HAs presence, water chemistry and exposure time in dispersion media.

Chronic exposure to copper oxide nanoparticles causes muscle toxicity in adult zebrafish

Repeated deposition of copper oxide nanoparticles (CuO-NPs) into aquatic systems makes them a global threat since the NPs accumulate in various organs of the fish particularly skeletal muscle. In the present study, adult zebrafish were exposed to different concentrations of CuO-NPs (1 and 3 mg/L) for a period of 30 days. The status of functional markers (acetylcholinesterase, creatine kinase-MB, and lactate dehydrogenase) and oxidative stress markers (oxidants and antioxidants) were analyzed. The histological changes in muscle were studied followed by the immunohistochemistry expression for catalase. Further, the expression of myoD, myogenin, pax7, β-actin, and desmin was examined by semi-quantitative reverse transcriptase polymerase chain reaction. The results indicated that chronic exposure to CuO-NPs causes muscular damage as evidenced by elevated levels of functional markers. There was a significant increase in the oxidants with reduction in the antioxidant levels, implying that the antioxidant enzymes were unable to scavenge the free radicals induced by the CuO-NPs. The histopathological analysis showed degeneration and atrophy in the treated groups confirming muscle damage. The immunohistochemical catalase expression in the muscle was reduced in the treated groups further supporting the evidence that the antioxidant has suffered a decline. The altered gene expression indicates skeletal muscle damage due to the CuO-NPs exposure. Overall, the data suggest that chronic exposure to CuO-NPs caused muscular toxicity which may lead to muscle degeneration in adult zebrafish.

Sustainability Outcomes of Green Processes in Relation to Industry 4.0 in Manufacturing: Systematic Review

Green processes are very important for the implementation of green technologies in production to achieve positive sustainability outcomes in the Industry 4.0 era. The scope of the paper is to review how conventional green processes as a part of Industry 4.0 provide sustainability outcomes in manufacturing. The paper is based on the methodology of systematic literature review through the content analysis of literary resources. Twenty-nine studies were included in our content analysis. The results show the main focus of current literature related to Industry 4.0, sustainability outcomes and green processes. The authors present a conceptual Sustainability Green Industry 4.0 (SGI 4.0) framework that helps to structure and evaluate conventional green processes in relation to Industry 4.0 and sustainability. The study summarizes which technologies (big data, cyber-physical systems, Industrial Internet of Things and smart systems) and green processes (logistics, manufacturing and product design) are important for achieving a higher level of sustainability. The authors found that the most often common sustainability outcomes are energy saving, emission reduction, resource optimalization, cost reduction, productivity and efficiency and higher economic performance, human resources development, social welfare and workplace safety. The study suggests implications for practice, knowledge and future research.

A Review of Metal and Metal-Oxide Nanoparticle Coating Technologies to Inhibit Agglomeration and Increase Bioactivity for Agricultural Applications

Coatings offer a means to control nanoparticle (NP) size, regulate dissolution, and mitigate runoff when added to crops through soil. Simultaneously, coatings can enhance particle binding to plants and provide an additional source of nutrients, making them a valuable component to existing nanoparticle delivery systems. Here, the surface functionalization of metal and metal-oxide nanoparticles to inhibit aggregation and preserve smaller agglomerate sizes for enhanced transport to the rooting zone and improved uptake in plants is reviewed. Coatings are classified by type and by their efficacy to mitigate agglomeration in soils with variable pH, ionic concentration, and natural organic matter profiles. Varying degrees of success have been reported using a range of different polymers, biomolecules, and inorganic surface coatings. Advances in zwitterionic coatings show the best results for maintaining nanoparticle stability in solutions even under high salinity and temperature conditions, whereas coating by the soil component humic acid may show additional benefits such as promoting dissolution and enhancing bioavailability in soils. Pre-tuning of NP surface properties through exposure to select natural organic matter, microbial products, and other biopolymers may yield more cost-effective nonagglomerating metal/metal-oxide NPs for soil applications in agriculture.

Multistep Method to Extract Moderately Soluble Copper Oxide Nanoparticles from Soil for Quantification and Characterization

The objective of this study is to assess how method parameters impact the extraction of moderately soluble CuO nanoparticles (NPs) from a standard natural soil (LUFA 2.1) suitable for chemical analysis. The extraction procedure is comprised of three steps: (i) preconditioning the soil to increase the sodium adsorption ratio, (ii) extracting colloids/NPs from the soil matrix using sonication and a dispersing agent, and (iii) separating the dissolved and nanoparticulate CuO fractions using cloud point extraction. Method parameters of the extraction procedure, including sonication, number of extraction cycles, and dispersing agent, were adjusted to achieve the highest extraction of CuO NPs, while minimizing dissolution. The maximum recovery of CuO NPs ranged from 31% to 42% for an amended concentration range of 10-250 mg-Cu (kg soil)^-1 using a preconditioning step to exchange divalent cations for monovalent ions, 0.2% carboxymethyl cellulose (CMC) 700 kg mol^-1 as the dispersing agent, probe sonication for 1 min, 3 extraction cycles, and a 1:10 soil-to-liquid ratio. CuO NPs that are polyvinylpyrrolidone (PVP)-coated with a greater stability against aggregation had significantly higher extractability and dissolution. This procedure is the first to effectively extract moderately soluble NPs from soil and experimentally separate them from their dissolved fraction and can be applied to other moderately soluble metal containing natural, incidental, or engineered NPs in soil.

The effect of pH and ageing on the fate of CuO and ZnO nanoparticles in soils

The objective of this study was to evaluate the fractionation of ZnO and CuO engineered nanoparticles (ENPs) in soils with a pH adjusted to 4.0, 6.5, and 9.0 after 1 day and 30 days of incubation. Based on the multi-stage extraction, 5 fractions of metals were determined. Moreover, the effect of ENPs on the activity of acid, neutral and alkaline phosphatase was determined. The results of the study revealed that pH had a dominant effect on the metal participation in soils. The levels of those fractions of metals differed between nano-ZnO and nano-CuO, which could have resulted from differences in the dissolution of the ENPs. After 1 day, the concentration of Zn²⁺ (0.02-7.4 mg L^-1) was 10 times higher than that of Cu²⁺. The metal fractionation in soil treated with ENPs and metal salts may also confirm the role of ENP dissolution. The concentration of potentially bioavailable fraction of Zn increased with a drop in pH. At a 4 pH concentration of Zn in the treatment with nano-ZnO and ZnCl₂ was at a similar level (42.1-45 mg kg^-1), whereas the addition of nano-CuO resulted in a lower content of Cu (24.7 mg kg^-1) than CuCl₂ (36.5 mg kg^-1). On the other hand, the concentration of fraction exchangeable of both metals in the alkaline soil did not exceed the level of 5.0 mg kg^-1. Sample incubation time was especially important for metal participation in samples with a pH of 6.5. The greatest differentiation of metal fractionation between the soils was also noted at a pH of 6.5, which could also have been a result of other properties of the soils. The strong effect of pH on the lability of ENPs in soils confirmed a need to trace the fate of ENPs in extreme soil conditions as well as in changing environment.

Phytotoxicity Assessment of Copper Oxide Nanoparticles on the Germination, Early Seedling Growth, and Physiological Responses in Oryza sativa L

The increasing utilization of copper oxide nanoparticles (CuO NPs) and their release into the environment has made it imperative to elucidate their impact on the ecological system including plants. However, their potential toxic impact and mechanisms on plant growth are still unclear. The aim of this study was to investigate the effects of CuO NPs and released Cu ions on seed germination and early seedling growth, as well as physiological and biochemical parameters of Oryza sativa. The results showed that CuO NPs at high concentration significantly inhibited seed germination and early seedling growth. The toxicity of CuO NPs originated from the particulate NPs rather than the released Cu²⁺. The phytotoxicity of CuO NPs to rice seed germination and seedling growth probably induced by high Cu accumulation along with the lignification and oxidative damage. The work presented here will increase our knowledge of phytotoxicity of CuO NPs.

Bioavailability and translocation of metal oxide nanoparticles in the soil-rice plant system

To determine the bioavailability and translocation of metal oxide nanoparticles (MONPs) in the soil-rice plant system, we examined the accumulation and micro-distribution of ZnO nanoparticles (NPs), CuO NPs and CeO₂ NPs (50, 100 and 500 mg/kg) in the paddy soil and rice plants under flooded condition for 30 days using single-step chemical extraction and diffusive gradients in thin films (DGT) technique combined with micro X-ray fluorescence spectroscopy (μ-XRF). The results show that various MONPs changed the soil properties, especially the redox potential was enhanced to -165.33 to -75.33 mV compared to the control. The extraction efficiency of Zn, Cu and Ce in the paddy soil from high to low was EDTA, DTPA, CaCl₂ and DGT. Moreover, exposure to 500 mg/kg CuO NPs and CeO₂ NPs induced the primary accumulation of Cu and Ce elements in rice roots as high as 235.48 mg Cu/kg and 164.84 mg Ce/kg, respectively, while the Zn concentration in shoots was up to 313.18 mg/kg under highest ZnO NPs with a 1.5 of translocation factor. The effect of MONPs on the plant growth was mainly related to the chemical species and solubility of MONPs. Micro-XRF analysis shows that Zn was mostly located in the root cortex while Cu was primarily accumulated in the root exodermis and few Ce distributed in the root. Pearson correlation coefficients indicate that only DTPA-extracted metals in soil were significantly and well correlated to the Zn, Cu and Ce accumulation in rice seedlings exposed to MONPs. This work is of great significance for evaluating the environmental risks of MONPs in soil and ensuring the safety of agricultural products.

The promoted dissolution of copper oxide nanoparticles by dissolved humic acid: Copper complexation over particle dispersion

Humic substances are the dominant dissolved organic matter fraction in the aqueous phase of environmental media. They would inevitably react with chemicals released into the environment. The influence of dissolved humic acid (DHA) on the dissolution and dispersion of copper oxide nanoparticles (CuO NPs, 50 nm, 49.57 mg L^-1) was therefore investigated in the present study. In addition to dispersing CuO NPs and reducing the size of the aggregates, the amount of released Cu from CuO NPs was found to increase over time with increasing concentrations of DHA, 96% of which was present as organic complexes after 72 h. At DHA concentrations exceeding 16.09 mg C L^-1, the complexation coefficients of DHA with Cu and the adsorptivity of CuO NPs to DHA were both reduced due to increased homo-conjugation of DHA as promoted by negative charge-assisted H-bond. Although the adsorption capacity of DHA kept increasing up to 57.07 mg C L^-1, the hydrodynamic diameter and ζ-potential were similar and the percentages of total released Cu continued to increase linearly to 4.92% at higher levels of DHA (30.13-57.07 mg C L^-1). Thereupon, DHA promoted the dissolution of CuO NPs in a concentration-dependent fashion. The driving force was complexation of Cu by DHA, rather than the balancing between the exposed and the covered surface area of the CuO NPs due to DHA adsorption. Our findings facilitate understanding the underlying mechanisms on how DHA impacts the CuO NPs environmental behavior (or fate) as well as on their kinetics.

Toxicities of copper oxide nanomaterial and copper sulphate in early life stage zebrafish: Effects of pH and intermittent pulse exposure

Effort has been made to standardise regulatory ecotoxicity tests for engineered nanomaterials (ENMs), but the environmental realism of altered water quality and/or pulse exposure to these pollutants should be considered. This study aimed to investigate the relative toxicity to early life-stage zebrafish of CuO ENMs at acid pH and then under pulse exposure conditions, all compared to CuSO₄. At all pH values, CuSO₄ was more toxic to zebrafish than CuO ENMs. Additions of H⁺ were protective of CuSO₄ toxicity, with median lethal concentrations LC₅₀ (with 95% confidence intervals) of: 0.36 (0.33-0.40), 0.22 (0.20-0.24) and 0.27 (0.25-0.29) mg L^-1 at pH 5, pH 6 and pH 7, respectively. In contrast, the toxicity of CuO ENMs increased with acidity; LC₅₀ values were: 6.6 (4.5-8.5), 19.4 (11.6-27.2) and >100 mg L^-1 at pH 5, pH 6 and pH 7, respectively. The increased toxicity of the CuO ENMs in acid water corresponded with greater dissolution of dissolved Cu from the particles at low pH, suggesting free Cu²⁺ ion delivery to the zebrafish was responsible for the pH-effect. In continuous 96 h exposures to the substances at the LC₁₀ values and at pH 6, both CuSO₄ and CuO ENMs caused Cu accumulation, inhibition of Na⁺/K⁺-ATPase and depletion of total glutathione in zebrafish. However, two 24 h pulses of CuSO₄ or CuO ENMs at the same peak concentration caused similar effects to the continuous 96 h exposure, despite the shorter exposure durations of the former; suggesting that the pulses were more hazardous than the continuous exposure. In conclusion, the current water quality correction for pH with respect to Cu toxicity to freshwater fish should not be applied to the nano form. Crucially, CuO ENMs are more toxic in pulse than continuous exposure and new corrections for both water pH and the Cu exposure profile are needed for environmental risk assessment.

Influence of sulfur fertilization on CuO nanoparticles migration and transformation in soil pore water from the rice (Oryza sativa L.) rhizosphere

The biogeochemical cycling of sulfur in soil is closely associated with the mobility and bioavailability of heavy metals; however the influence of sulfur on the behavior of metal-based nanoparticles has not yet been studied. The influence of S fertilizer (S⁰ and Na₂SO₄) applied in paddy soils on CuO NPs behavior in soil pore water was explored in the present study. Synchrotron-based techniques were applied to investigate the migration and speciation transformation of CuO NPs in soil pore water colloids. The application of sulfur fertilizer increased the zeta potential of soil colloids from the rice rhizosphere region and reduced the size of the colloids. Sulfur fertilization decreased the concentration of Cu in soil pore water in the rice rhizosphere region. S⁰ fertilizer reduced the Cu concentration in soil colloids (by 55.8%-73.5%), while Na₂SO₄ increased the Cu concentration in soil colloids (by 173.8%-265.1%). Sulfur fertilization changed the spatial distribution of Fe³⁺ and Cu²⁺ in colloids, making these ions more likely to be aggregated on the edges of soil colloids. Speciation transformation of CuO NPs happened during the process of migration. The main Cu speciation in the soil colloids were CuO NPs, Cu-Cysteine, Cu₂S and Cu-Citrate. Sulfur fertilization increased the proportion of Cu₂S (by 40.5%) in soil pore water colloids from the rice rhizosphere region, while the proportion of CuO NPs was reduced (by 18.4%). Sulfur fertilization changed the morphology and elementary composition of colloids in soil pore water, thus influencing the migration of CuO NPs in the soil column through soil colloids.

Does soil CuO nanoparticles pollution alter the gut microbiota and resistome of Enchytraeus crypticus?

Growing evidence suggests that metallic oxide nanoparticles can pose a severe risk to the health of invertebrates. Previous attention has been mostly paid to the effects of metallic oxide nanoparticles on the survival, growth and physiology of animals. In comparison, the effects on gut microbiota and incidence of antibiotic resistance genes (ARGs) in soil fauna remain poorly understood. We conducted a microcosm study to explore the responses of the non-target soil invertebrate Enchytraeus crypticus gut microbiota and resistomes to copper oxide nanoparticles (CuO NPs) and copper nitrate by using bacterial 16S rRNA gene amplicons sequencing and high throughput quantitative PCR. The results showed that exposure to Cu²⁺ resulted in higher bioaccumulation (P < 0.05) and lower body weight and reproduction (P < 0.05) of Enchytraeus crypticus than exposure to CuO NPs. Nevertheless, exposure to CuO NPs for 21 days markedly increased the alpha-diversity of the gut microbiota of Enchytraeus crypticus (P < 0.05) and shifted the gut microbial communities, with a significant decline in the relative abundance of the phylum Planctomycetes (from 37.26% to 19.80%, P < 0.05) and a significant elevation in the relative abundance of the phyla Bacteroidetes, Firmicutes and Acidobacteria (P < 0.05). The number of detected ARGs in the Enchytraeus crypticus gut significantly decreased from 45 in the Control treatment to 16 in the Cu(NO₃)₂ treatment and 20 in the CuO NPs treatment. The abundance of ARGs in the Enchytraeus crypticus gut were also significantly decreased to 38.48% when exposure to Cu(NO₃)₂ and 44.90% when exposure to CuO NPs (P < 0.05) compared with the controls. These results extend our understanding of the effects of metallic oxide nanoparticles on the gut microbiota and resistome of soil invertebrates.

Influence of water chemistry on colloid-size Cu-based pesticides particles: A case of Cu(OH)2 commercial fungicide/bactericide

The intensive, widespread, and ever-increasing applications of Cu-based pesticides in agriculture could potentially increase environmental exposures via different routes. Unlike ionic/bulk forms, the fate, transport, and toxicity of colloid-size Cu-based pesticides are not well studied. This paper provides evaluation outcomes of granule and dispersion characterizations, stability, and dissolution of colloid-size particles of Cu(OH)₂ commercial pesticide product at a range of water chemistry. The evaluated product contained about 35% weight of metallic Cu equivalent and Cu(OH)₂ particles with sizes < 1 μm of which a fraction of nanoscale particles exist. The presence of Ca²⁺ at ionic strengths of >0.01 M and 0.001-0.2 M significantly influenced (p < 0.001) particle size (PS) and ζ-potential values, respectively at all investigated pH values. Cu dissolution at pH 5.5 was significant (p < 0.001) and exceeded Cu dissolutions at pH 7.0 by 87-90% and at pH 8.5 by 87-95% in all dispersions. The order of Cu dissolution was pH 5.5 > pH 7.0 > pH 8.5 in all dispersions. Cu dissolution was relatively reduced by 53% by increasing HA from 0 to 5 mg L^-1 and enhanced by 55% by increasing HA from 5 to 15 mg L^-1, however, the overall Cu dissolution was decreased by 27% by increasing HA from 0 to 15 mg L^-1. Thus, HAs reduced the dissolution of Cu at pH < 7. The findings provide an insight into how water chemistry influences the fate and transport of colloid-size Cu-based pesticides particles.

The effect of natural organic compounds on the adsorption of toluene and ethylene benzene on MWCNT

PURPOSE

The present study aimed to investigate the effect of humic acid (as a NOM model) on the adsorption capacity of MWCNT.

METHODS

Ethyl benzene and toluene were removed from aqueous solution and adsorbed on multi walled carbon nanotubes in batch adsorption experiments at the presence of different concentrations of humic acid.

RESULTS

The results showed that the highest adsorption of multi walled carbon nanotubes was 72 mg/g for ethyl benzene and 35 mg/g for toluene in an aqueous solution without humic acid. Langmuir isotherm model and pseudo-second-order kinetic model were the predominant models of adsorption process. Pre-loading of humic acid on MWCNT reduced the adsorption capacity of MWCNT from 14 mg/g to 8 mg/g for toluene and from 25 mg/g to 10 mg/g for ethyl benzene, when the experiments were conducted with MWCNT pre-loaded by humic acid from 0 to 30% .

CONCLUSIONS

The batch adsorption experiments showed that the presence of dissolved humic acid in the aqueous environment slightly affected the adsorption of ethyl benzene and toluene by MWCNT but, Pre-loading of humic acid on MWCNT could reduce the adsorption capacity of multi walled carbon nanotubes.

Montmorillonite clay and humic acid modulate the behavior of copper oxide nanoparticles in aqueous environment and induces developmental defects in zebrafish embryo

Copper oxide nanoparticles (CuO NPs) is one of the most commonly used metal oxide nanoparticles for commercial and industrial products. An increase in the manufacturing and use of the CuO NPs based products has increased the likelihood of their release into the aquatic environment. This has attracted major attention among researchers to explore their impact in human as well as environmental systems. CuO NPs, once released into the environment interact with the biotic and abiotic constituents of the ecosystem. Hence the objective of the study was to provide a holistic understanding of the effect of abiotic factors on the stability and aggregation of CuO NPs and its correlation with their effect on the development of zebrafish embryo. It has been observed that the bioavailability of CuO NPs decrease in presence of humic acid (HA) and heteroagglomeration of CuO NPs occurs with clay minerals. CuO NPs, CuO NPs + HA and CuO NPs + Clay significantly altered the expression of genes involved in development of dorsoventral axis and neural network of zebrafish embryos. However, the presence of HA with clay showed protective effect on zebrafish embryo development. These findings provide new insights into the interaction of NPs with abiotic factors and combined effects of such complexes on developing zebrafish embryos genetic markers.

Biogenic synthesis of copper oxide nanoparticles using plant extract and its prodigious potential for photocatalytic degradation of dyes

The development of benign and efficient approaches for treating industrial grade toxic organic dyes is an ongoing challenge. To this end, copper oxide nanoparticles (CuO NPs) were prepared by a simple, environment friendly, and economical green synthesis procedure by using Psidium guajava leaf extract as reducing agent (i.e., for the reduction of metal salt) as well as capping agent and copper acetate monohydrate as metal salt. The formation of mono-dispersed and spherical (average size 2-6 nm with BET surface area 52.6 m²/g) CuO NPs was confirmed by various spectroscopic and microscopic techniques. The CuO NPs exhibited excellent degradation efficiency for the industrial dyes, i.e., Nile blue (NB) (93% removal in 120 min) and reactive yellow 160 (RY160) (81% removal in 120 min) with apparent rate constants of 0.023 and 0.014 min^-1, respectively. The CuO catalyst was found to be reusable for photocatalytic dye degradation even after five consecutive cycles. The limit of detection (LOD) values for NB and RY160 were 4 and 9 mg/L, respectively. In light of their high reusability and photocatalytic efficiency along with adaptability to green synthesis, the use of biogenic CuO NPs is a promising option for the purification of water resources contaminated with industrial dye.