Biodegradable plastic agricultural mulches and key features of microbial degradation

Response of terrestrial crustacean Porcellio scaber and mealworm Tenebrio molitor to non-degradable and biodegradable fossil-based mulching film microplastics

Agricultural mulching films are potential sources of microplastics (MPs) in soil. As an alternative to conventional non-degradable mulching films, a variety of different biodegradable mulching films are used. However, it is not yet known whether MPs from biodegradable mulching films pose a lower risk to terrestrial invertebrates compared to MPs from conventional mulching films. In this study, the effects of MPs produced from two conventional polyethylene (PE-1 and PE-2) and two biodegradable (starch-based poly(butylene adipate co-terephthalate); PBAT-BD-1, and PBAT-BD-2) fossil-based mulching films on terrestrial crustacean woodlice Porcellio scaber and mealworm Tenebrio molitor were compared. A key finding was that no clear differences in induced responses between biodegradable and conventional MPs were detected. No adverse effects on P. scaber after two weeks and on T. molitor after four weeks of exposure were observed up to 5 % (w/w dry soil) of either MP type. However, some sublethal physiological changes in metabolic rate and immune parameters were found in P. scaber after two weeks of exposure indicating a response of organisms to the presence of MP exposure in soil. In addition, it was demonstrated that both types of MPs might affect the soil water holding capacity and pH. In conclusion, we confirmed that biodegradable MPs can induce responses in organisms hence further studies testing the environmental hazard of biodegradable MPs are justified.

Microplastic effects on carbon cycling in terrestrial soil ecosystems: Storage, formation, mineralization, and microbial mechanisms

Soil is the largest environmental reservoir of microplastics (MPs) on the earth. Incremental accumulation of MPs in the soil can cause significant changes in soil physicochemical and microbial traits, which may in turn interfere with soil biogeochemical processes such as carbon cycling. With published research regarding MPs impacts on soil carbon cycling growing rapidly, a systematic review summarizing the current knowledge and highlighting future research needs is warranted. As carbon-rich polymers, MPs can contribute to soil organic carbon (SOC) storage via degradation and leaching. MPs can also affect the humification of dissolved organic matters (DOM), consequently influencing the stability of SOC. Exposure to MPs can cause substantial impacts on the growth performance, litter decomposition, and root secretion of terrestrial plants as well as soil microbial carbon turnover, inducing changes in the formation of SOC. The presence of MPs has contrasting effects on the emissions of both CO2 and CH4 from the soil. The diverse effects of MPs on soil carbon metabolism could be partly attributed to the varying changes in soil microbial community structure, functional gene expression, and enzyme activity under MPs exposure. Further research is still highly needed to clarify the pathways of MPs impacts on soil carbon cycling and the driving biological and physicochemical factors behind these processes.

Comparative evaluation of the impacts of different microplastics on greenhouse gas emissions, microbial community structure, and ecosystem multifunctionality in paddy soil

Although the increasing accumulation of microplastics (MPs) in terrestrial soil ecosystems has aroused worldwide concern, research remains limited on their potential impacts on soil processes and ecosystem functionality. Here, through a 41-day microcosm experiment, we found that polylactic acid (PLA), low-density polyethylene (LDPE), and polypropylene (PP) MPs consistently increased soil carbon nutrients and pH but had varying effects on soil nitrogen nutrients and the chemodiversity of dissolved organic matter (DOM). Different treatments led to notable shifts in the α-diversity and composition of soil microbial community, with phyla Proteobacteria and Ascomycota consistently enriched by MPs regardless of polymer type. The emissions of CO2 and N2O were suppressed by MPs in most cases, which in combination led to a decline in global warming potential. LDPE and 1 - 1.5 % of PLA MPs significantly improved the multifunctionality of the soil ecosystem, while PP and 0.5 % of PLA MPs exerted an opposite effect. Soil total organic carbon, pH, DOM molecular mass and condensation degree, and CO2 emissions were identified as the most important variables for predicting soil ecosystem multifunctionality. Results of this study can extend the current understanding of the impacts of MPs on soil biogeochemical cycling and ecosystem functionality.

Research progress on degradation of biodegradable micro-nano plastics and its toxic effect mechanism on soil ecosystem

Biodegradable plastics (BPs) are known to decompose into micro-nano plastics (BMNPs) more readily than conventional plastics (CPs). Given the environmental risks posed by BMNPs in soil ecosystems, their impact has garnered increasing attention. However, research focusing on the toxic effects of BMNPs on soils remains relatively limited. The degradation process and duration of BMNPs in soil are influenced by numerous factors, which directly impact the toxic effects of BMNPs. This highlights the urgent need for further research. In this context, this review delineates the classification of BPs, investigates the degradation processes of BPs along with their influencing factors, summarizes the toxic effects on soil ecosystems, and explores the potential mechanisms that underlie these toxic effects. Finally, it provides an outlook on related research concerning BMNPs in soil. The results indicate that specific BMNPs release additives at a faster rate during decomposition, degradation, and aging, with certain compounds exhibiting increased bioavailability. Importantly, a substantial body of research has shown that BMNPs generally manifest more pronounced toxic effects in comparison to conventional micro-nano plastics (CMNPs). The toxic effects associated with BMNPs encompass a decline in soil quality and microbial biomass, disruption of nutrient cycling, inhibition of plant root growth, and negative impacts on invertebrate reproduction, survival, and fertilization rates. The rough and complex surfaces of BMNPs contribute to increased mechanical damage to tested organisms, enhance absorption by microorganisms, and disrupt normal physiological functions. Notably, the toxic effects of BMNPs on soil ecosystems are influenced by factors including concentration, type of BMNPs, exposure conditions, degradation products, and the nature of additives used. Therefore, it is crucial to standardize detection technologies and toxicity testing conditions for BMNPs. In conclusion, this review provides scientific evidence that supports effective prevention and management of BMNP pollution, assessment of its ecological risks, and governance of BMNPs-related products.

Mineralization and microbial utilization of poly(lactic acid) microplastic in soil

The current carbon dioxide (CO2) evolution-based standard method for determining biodegradable microplastics (MPs) degradation neglects its priming effect on soil organic matter decomposition, which misestimates their biodegradability. Here, a 13C natural abundance method was used to estimate the mineralization of poly(lactic acid) (PLA) MP in various agricultural soils, and to trace its utilization in different microbial groups. In alkaline soils, the PLA-derived CO2 emissions increased with increasing soil carbon/nitrogen (C/N) ratios, and the mineralization of PLA MP concentrations ranged from 3-33 %, whereas the CO2 evolution method probably over- or under-estimated the mineralization of PLA in alkaline soils with different soil C/N ratios. Low PLA mineralization (1-5 %) were found in the acidic soil, and the standard method largely overestimated the mineralization of PLA MP by 1.3- to 3.3-fold. Moreover, the hydrolysate of PLA MP was preferentially assimilated by Gram-negative bacteria, but Gram-positive bacterial decomposition mainly contributed to the release of PLA-derived CO2 at low MP concentrations (≤ 1 %). Overall, the 13C natural abundance method appears to be suitable for tracking the mineralization and microbial utilization of biodegradable PLA in soils, and the PLA-derived C is mainly assimilated and decomposed by bacterial groups.

Quercetin-loaded melanin nanoparticle mediated konjac glucomannan/polycaprolactone bilayer film with dual-mode synergistic bactericidal activity for food packaging

It is still difficult for a single antibacterial modality to realize satisfactory management of bacterial breeding in food preservation. To solve this problem, we developed a photothermal-derived dual-mode synergistic bactericidal konjac glucomannan (KGM)/polycaprolactone (PCL) bilayer film incorporated with quercetin-loaded melanin-like nanoparticles (Q@MNPs). The results showed that the mechanical properties (TS: 29.8 MPa, EAB: 43.1 %), UV shielding properties, and water resistance (WCA: 124.1°, WVP: 3.92 g mm/m2 day kPa) of KGM-Q@MNPs/PCL bilayer films were significantly improved. More importantly, KGM-Q@MNPs/PCL bilayer film presented outstanding photothermal inversion and controlled release behavior of Q triggered by near infrared (NIR) radiation, thus contributing to excellent dual-mode synergistic antibacterial properties against E. coli and S. aureus. Meanwhile, the KGM-Q@MNPs/PCL bilayer film possessed good biocompatibility and low toxicity. As a proof-of-concept application, we further verified the significant value of film for the preservation of cherry tomatoes. Since KGM-Q@MNPs/PCL bilayer film showed excellent biodegradability, this work will aid the development of sustainable antibacterial food packaging materials.

Toward a Circular Bioeconomy: Designing Microbes and Polymers for Biodegradation

Polymer production is rapidly increasing, but there are no large-scale technologies available to effectively mitigate the massive accumulation of these recalcitrant materials. One potential solution is the development of a carbon-neutral polymer life cycle, where microorganisms convert plant biomass to chemicals, which are used to synthesize biodegradable materials that ultimately contribute to the growth of new plants. Realizing a circular carbon life cycle requires the integration of knowledge across microbiology, bioengineering, materials science, and organic chemistry, which itself has hindered large-scale industrial advances. This review addresses the biodegradation status of common synthetic polymers, identifying novel microbes and enzymes capable of metabolizing these recalcitrant materials and engineering approaches to enhance their biodegradation pathways. Design considerations for the next generation of biodegradable polymers are also reviewed, and finally, opportunities to apply findings from lignocellulosic biodegradation to the design and biodegradation of similarly recalcitrant synthetic polymers are discussed.

The Impact of Abiotic and Biotic Conditions for Degradation Behaviors of Common Biodegradable Products in Stabilized Composts

This work examines the influence of the degradation behaviors of biotic and abiotic conditions on three types of biodegradable products: cups from PLA and from cellulose, and plates from sugarcane. The main objective of this study was to evaluate if biodegradable products can be degraded in composts that were stabilized by backyard composting. Furthermore, the impact of crucial abiotic parameters (temperature and pH) for the degradation behaviors process was investigated. The changes in the biopolymers were analyzed by FTIR spectroscopy. This work confirmed that abiotic and biotic conditions are important for an effective disintegration of the investigated biodegradable products. Under abiotic conditions, the degradation behaviors of PLA were observable under both tested temperature (38 and 59 °C) conditions, but only at the higher temperature was complete disintegration observed after 6 weeks of incubation in mature compost. Moreover, our research shows that some biodegradable products made from cellulose also need additional attention, especially with respect to incorporated additives, as composting could be altered and optimal conditions in composting may not be achieved. This study shows that the disintegration of biodegradable products is a comprehensive process and requires detailed evaluation during composting. The results also showed that biodegradable products can also be degraded post composting and that microplastic pollution from biodegradable polymers in soil may be removed by simple physical treatments.

Sustainable seedling pots: Development and characterisation of banana waste and natural fibre-reinforced composites for horticultural applications

Plastic pots used in horticultural nurseries generate substantial waste, causing environmental pollution. This study aimed to develop biodegradable composites from banana pseudo-stem reinforced with agricultural residues like pineapple leaves, taro and water hyacinth as eco-friendly substitutes. The aim of this study is to develop optimised banana biocomposite formulations with suitable reinforcements that balance mechanical durability, biodegradation, and seedling growth promotion properties to serve as viable eco-friendly alternatives to plastic seedling pots. This study was carried out by fabricating banana fibre mats through pulping, drying and hot pressing. Composite sheets were reinforced with 50 % pineapple, taro or water hyacinth fibres. The mechanical properties (tensile, yield strength, elongation, bursting strength), hydrophilicity (contact angle, water absorption), biodegradability (soil burial test), and seedling growth promotion were evaluated through appropriate testing methods. The results show that banana-taro composites exhibited suitable tensile strength (25 MPa), elongation (27 %), water uptake (41 %) and 82 % biodegradation in 60 days. It was observed that biodegradable seedling trays fabricated from banana-taro composite showed 95 % tomato seed germination and a 125 cm plant height increase in 30 days, superior to plastic trays. The finding shows that the study demonstrates the potential of banana-taro biocomposites as alternatives to plastic nursery pots, enabling healthy seedling growth while eliminating plastic waste pollution through biodegradation.

Comparison of the Effects of LDPE and PBAT Film Residues on Soil Microbial Ecology

The plastic film is extensively applied with limited recycling, leading to the long-run residue accumulation in soil, which offers a distinctive habitat for microorganisms, and creates a plastisphere. In this study, traditional low-density polyethylene (LDPE) plastic film and biodegradable polybutylene adipate terephthalate (PBAT) plastic film materials were selected to test their effects on soil microbial ecology. Based on high-throughput sequencing, compared to the soil environment, the alpha-diversity of bacterial communities in plastisphere was lower, and the abundance of Actinobacteria increased. Plastic film residues, as bacterial habitats, exhibited greater heterogeneity and harbor unique bacterial communities. The communities were distinguished between plastisphere and soil environment by means of a random-forest (RF) machine-learning model. Prominent distinctions emerged among bacterial functions between soil environment and plastisphere, especially regarding organics degradation. The neutral model and null model indicated that the constitution of bacterial communities was dominated by random processes except in LDPE plastisphere. The bacterial co-occurrence network of the plastisphere exhibited higher complexity and modularity. This study contributes to our comprehending of characteristics of plastisphere bacterial communities in soil environment and the associated ecological risks of plastic film residues accumulation.

Biochar as a sustainable alternative to carbon black in agricultural mulch films

Examples of biochar as an alternative to traditional plastic fillers, like carbon black, are numerous and growing. However, in the agricultural mulch film application, both the polymer and its fillers are pushed to their mechanical limit to obtain an effective product, using the least amount of plastic. Through a combined techno-economic analysis (TEA) and life cycle assessment (LCA), this study characterizes the use of carbon-negative biochar as an opacity filler in mulch film applications. Due to its larger particle size, the biochar demands additional thickness to achieve equivalent opacity as carbon black in films. A thicker film translates to additional polymer demand, and a significant increase in price and environmental impact. A comparable formulation for an equal price ($623 per mulched ha) as a 2.6 wt % carbon black with 25 μm thickness was derived, needing 15 wt % biochar and a thickness of 30 μm. The biochar formulation resulted in a slightly higher global warming potential (3% increase), but much larger impact in the land use category (+339%), and the sample was deemed not fit for use in the intended mulch application. These results indicate that in applications where the polymeric matrix and its fillers are pushed to their mechanical limit, the displacement of traditional fillers by biochar is challenging. However, biochar derived from waste biomass (thus reducing land use impact) remains a valid, environmentally beneficial solution to displace traditional fillers for non-extreme plastic uses (commodity plastics) and thicker composites.

Impacts of pristine, aged and leachate of conventional and biodegradable plastics on plant growth and soil organic carbon

Plastic is an essential component of agriculture globally, becoming a concerning form of pollution. Biodegradable alternatives are gaining attention as a potential replacement for commonly used, non-degradable plastics, but there is little known about the impacts of biodegradable plastics as they age and potential leachates are released. In this study, different types (conventional: polyethylene and polypropylene and biodegradable: polyhydroxybutyrate and polylactic acid) of micro- and meso-films were added to soil at 0.1% (w/w) prior to being planted with Lolium perenne (perennial ryegrass) to evaluate the plant and soil biophysical responses in a pot experiment. Root and shoot biomass and chlorophyll content were reduced when soil was exposed to plastics, whether conventional or biodegradable, pristine, aged or when just their leachate was present. The pH and organic matter content of soil exposed to these plastics and their leachates was significantly reduced compared to control samples; furthermore, there was an increase in CO2 respiration rate from soil. In general, meso (> 5 mm) and micro (< 5 mm) plastic films did not differ in the impact on plants or soil. This study provides evidence that conventional and biodegradable plastics have both physical and chemical impacts on essential soil characteristics and the growth of L. perenne, potentially leading to wider effects on soil carbon cycling.

Enhanced biodegradable polyester film degradation in soil by sequential cooperation of yeast-derived esterase and microbial community

The degradation of biodegradable plastics poses a significant environmental challenge and requires effective solutions. In this study, an esterase derived from a phyllosphere yeast Pseudozyma antarctica (PaE) enhanced the degradation and mineralization of poly(butylene succinate-co-adipate) (PBSA) film in soil. PaE was found to substitute for esterases from initial degraders and activate sequential esterase production from soil microbes. The PBSA film pretreated with PaE (PBSA-E) rapidly diminished and was mineralized in soil until day 55 with high CO2 production. Soil with PBSA-E maintained higher esterase activities with enhancement of microbial abundance, whereas soil with inactivated PaE-treated PBSA film (PBSA-inact E) showed gradual degradation and time-lagged esterase activity increases. The fungal genera Arthrobotrys and Tetracladium, as possible contributors to PBSA-film degradation, increased in abundance in soil with PBSA-inact E but were less abundant in soil with PBSA-E. The dominance of the fungal genus Fusarium and the bacterial genera Arthrobacter and Azotobacter in soil with PBSA-E further supported PBSA degradation. Our study highlights the potential of PaE in addressing concerns associated with biodegradable plastic persistence in agricultural and environmental contexts.

Discrepant responses of bacterial community and enzyme activities to conventional and biodegradable microplastics in paddy soil

The prevalence of microplastics in soil ecosystems has raised concerns about their potential effects on soil properties. As promising alternatives to conventional plastics, biodegradable plastics have been increasingly applied in agricultural activities, which may release microplastics into the soil due to incomplete degradation. Compared to conventional microplastics, biodegradable microplastics in soil may induce different impacts on soil microbial properties, which have yet to be well studied. Through a 41-day microcosm experiment, we evaluated the differential effects of conventional (polypropylene, PP) and biodegradable (polylactic acid, PLA) microplastics on the geochemical properties, enzyme activities, and microbial community structure in paddy soil. Adding PLA or PP microplastics into soil significantly increased pH values and altered the contents of carbon and nitrogen nutrients. Exposure to microplastics significantly increased the activity of fluorescein diacetate hydrolase, but had varying effects on the activities of urease, sucrase, and alkaline phosphatase depending on microplastic types and doses. The addition of microplastics also influenced the structure of soil bacterial community, with Proteobacteria, Actinobacteriota, and Acidobacteriota being the dominant phyla. Significant differences in the genera of Pseudarthrobacter, Acidothermus, Bacillus, Aquisphaera, and Massilia were observed between treatments. Results of structural equation modeling (SEM) demonstrated that changes in soil carbon and nitrogen nutrients and pH values positively affected the bacterial community, while soil bacterial community as a whole exerted a negative impact on enzyme activities. FAPRPTAX analysis showed that the addition of microplastics altered the relative abundances of functional genes related to the metabolism of cellulose decomposition and ureolysis in paddy soil. Findings of this study clearly suggest that microplastic impacts on soil geochemical and microbial properties should be an integral part of future risk assessment and that to evaluate microplastic impacts, both the concentration and polymer type must be taken into account.

Are biodegradable mulch films a sustainable solution to microplastic mulch film pollution? A biogeochemical perspective

Mulch film residue contributes significantly to global plastic pollution, and consequently biodegradable mulch films (BDMs) are being adopted as a solution. BDMs decompose relatively quickly, but their complete biodegradation requires suitable conditions that are difficult to achieve in nature, causing biodegradable microplastics (bio-MPs) to be more likely to accumulate in soil than traditional microplastics (MPs). If BDMs are to be considered as a sustainable solution, long-term and in-depth studies to investigate the impact of bio-MPs on the biogeochemical processes are vital to agroecosystems operation and ecosystem services supply. Although bio-MP-derived carbon can potentially convert into biomass during decomposition, its contribution to soil carbon stocks is insignificant. Instead, given their biodegradability, bio-MPs can result in greater alterations of soil biodiversity and community composition. Their high carbon-nitrogen ratios may also significantly regulate various processes involved in the natural decomposition and transformation of soil organic matter, including the reduction of nutrient availability and increase in greenhouse gas emissions. Soil ecosystems are complex organic entities interconnected by disturbance-feedback mechanisms. Given the prevailing knowledge gaps regarding the impact of bio-MPs on soil biogeochemical cycles and ecosystem balance, this study emphasized the safety and sustainability assessment of bio-MPs and the prevailing comprehensive challenges.

Biodegradable mulch films improve yield of winter potatoes through effects on soil properties and nutrients

Biodegradable mulch films are recognized as a promising substitute of polyethylene (PE) films to alleviate the "white pollution". Biodegradable mulch films with optimum degradation rates increase crop yield even compared to PE films. However, the mechanisms underlying this yield-increasing effect remains elusive. In this study, three biodegradable film treatments (BFM1, BFM2 and BFM3) and one PE film treatment (PFM) were used to evaluate their effects on soil and winter potatoes, and a partial least squares path model (PLS-PM) was constructed to investigate their relationships. The degradation rates of films under different treatments were ranked as BFM3 > BFM2 >BFM1 > PFM, and presented distinctive effects on soil properties and nutrients, structure of soil bacterial community, and yield traits of winter potatoes. The PLS-PM showed that mulch treatments affected potato yield through effects on soil properties (soil water and temperature) and soil nutrients (TOC, DOC, TN and NO3--N). The disintegration of the biodegradable films decreased soil water content and temperature, and reduced the loss of soil nutrients in the topsoil at the later growth stage of winter potatoes compared to PE films. Additionally, the elevated content of soil TN and NO3--N under treatment BFM1 may play a key role in its yield-increasing effect on potatoes compared to treatments PFM and BFM2. Thus, biodegradable mulch films with proper degradation rates regulate soil TN and NO3--N through their effects on soil water and temperature, and subsequently improve the yield of winter potatoes compared to PE mulch films.

Organic composts as A vehicle for the entry of microplastics into the environment: A comprehensive review

Plastic pollution is a widespread issue that poses a threat to agroecosystems. Recent data on microplastic (MP) pollution from compost and its application to soil have highlighted the potential impact of micropollutants that may be transferred from compost. Thus, we aim with this review to elucidate the distribution-occurrence, characterization, fate/transport, and potential risk of MPs from organic compost to gain comprehensive knowledge and mitigate the adverse impacts of compost application. The concentration of MPs in compost was up to thousands of items/kg. Among micropollutants, fibers, fragments, and films are the most common, with small MPs having a higher potential to absorb other pollutants and cause harm to organisms. Various synthetic polymers, including polyethylene (PE), polypropylene (PP), polyethylene terephthalate (PET), polystyrene (PS), polyvinyl chloride (PVC), polyester (PES), and acrylic polymers (AP), have been widely used of plastic items. MPs are emerging pollutants that can have diverse effects on soil ecosystems, as they can transfer potential pollutants from MPs to compost and then to the soil. Following the microbial degradation scheme, the transfer chain from plastics to compost to soil can be broken down into main stages, i.e., colonization - (bio)fragmentation - assimilation - and mineralization. Microorganisms and adding biochar play an essential role during composting, which can be an effective solution to enhance MP degradation. Findings have shown that stimulating free radical generation could promote the biodegradation efficacy of MPs and possibly remove their occurrence in compost, thereby reducing their contribution to ecosystem pollution. Furthermore, future recommendations were discussed to reduce ecosystem risks and health challenges.

Insights into the abiotic fragmentation of biodegradable mulches under accelerated weathering conditions

Biodegradable mulches (BMs) can be tilled into soils to mitigate disposal and environmental problems. However, the content of biodegradable microplastics (BMPs) would increase with the addition of biodegradable macroplastics (BMaPs). The fragmented particles have a strong affinity to soil pollutants, having the potential to transfer via the terrestrial food web in an agroecosystem. Based on the spectral analysis and particle size analysis, this study explored the physicochemical characteristics of weathered BMaPs and BMP-derived dissolved organic matter (DOM_BMP). Ultraviolet (UV) irradiation reduced the mechanical strength of BMaPs and induced oxygenated functional groups, thus increasing surface roughness and hydrophilicity. This promoted the adsorption of aromatic compounds and heavy metals from soils to BMPs. After entering the water environment, the pH of the solution with DOM_BMP decreased, whereas the concentration of dissolved organic carbon (DOC) increased. Compared with paper mulch, bioplastic mulch contributed a higher amount of DOM_BMP, such as aromatic structure-containing chemicals and carboxylic acids, to the water environment but released fewer and smaller plastic particles. The findings from this study can help manage environmental risks and determine disposal strategies after the use of mulching.

Development of Epoxy and Urethane Thermosetting Resin Using Chlorella sp. as Curing Agent for Materials with Low Environmental Impact

In the current system, the disposal of plastic materials causes serious environmental pollution such as the generation of carbon dioxide and destruction of the ecosystem by micro-plastics. To solve this problem, bioplastics, biomass and biodegradable plastics have been developed. As part of our research, we have developed novel bioplastics called "cell-plastics", in which a unicellular green algal cell serves as a fundamental resource. The production of the cell-plastics would be expected to reduce environmental impact due to the usage of a natural product. Herein, to overcome the mechanical strength of cell-plastics, we used thermosetting epoxy and urethane resins containing Chlorella sp. as the green algae. We successfully fabricated thermosetting resins with a Chlorella sp. content of approximately 70 wt% or more. IR measurements revealed that the chemical structure of an epoxide or isocyanate monomer mixed with Chlorella sp. was modified, which suggests that the resins were hardened by the chemical reaction. In addition, we investigated the effect of thermosetting conditions such as temperature and compression for curing both resins. It was revealed that the Young's moduli and tensile strengths were controlled by thermosetting temperature and compression, whereas the elongation ratios of the resins were constant at low values regardless of the conditions.

Insights into the mechanisms involved in the fungal degradation of plastics

Fungi are considered among the most efficient microbial degraders of plastics, as they produce salient enzymes and can survive on recalcitrant compounds with limited nutrients. In recent years, studies have reported numerous species of fungi that can degrade different types of plastics, yet there remain many gaps in our understanding of the processes involved in biodegradation. In addition, many unknowns need to be resolved regarding the fungal enzymes responsible for plastic fragmentation and the regulatory mechanisms which fungi use to hydrolyse, assimilate and mineralize synthetic plastics. This review aims to detail the main methods used in plastic hydrolysis by fungi, key enzymatic and molecular mechanisms, chemical agents that enhance the enzymatic breakdown of plastics, and viable industrial applications. Considering that polymers such as lignin, bioplastics, phenolics, and other petroleum-based compounds exhibit closely related characteristics in terms of hydrophobicity and structure, and are degraded by similar fungal enzymes as plastics, we have reasoned that genes that have been reported to regulate the biodegradation of these compounds or their homologs could equally be involved in the regulation of plastic degrading enzymes in fungi. Thus, this review highlights and provides insight into some of the most likely regulatory mechanisms by which fungi degrade plastics, target enzymes, genes, and transcription factors involved in the process, as well as key limitations to industrial upscaling of plastic biodegradation and biological approaches that can be employed to overcome these challenges.

Molecular insights into effects of PBAT microplastics on latosol microbial diversity and DOM chemodiversity

The impact of biodegradable microplastics on the microbial community and dissolved organic matter (DOM) in latosol has not been well reported. In this study, an incubation experiment at 25 ºC for 120 days using latosol amended with low (5%) and high (10%) concentrations of polybutylene adipate terephthalate (PBAT) microplastics was carried out to explore the impacts of PBAT microplastics on soil microbial communities and DOM chemodiversity, and the intrinsic interactions between their shifts. The main bacterial and fungal phyla in soil, namely Chloroflexi, Actinobacteria, Chytridiomycota, and Rozellomycota showed a nonlinear relationship with PBAT concentration and played a pivotal role in shaping DOM chemodiversity. A higher decreased levels of lignin-like compounds and increased levels of protein-like and condensed aromatic compounds in the 5% treatment were observed than that in the 10% treatment. Furthermore, a higher increase relative abundance of CHO compounds in the 5% treatment than in the 10% treatment was ascribed to its higher oxidation degree. Co-occurrence network analysis suggested that bacteria formed more complex relationships with DOM molecules than fungi did, indicating their critical roles in DOM transformation. Our study has important implications for understanding the potential influence of biodegradable microplastics on carbon biogeochemical roles in soil.

Discovery of plastic-degrading microbial strains isolated from the alpine and Arctic terrestrial plastisphere

Increasing plastic production and the release of some plastic in to the environment highlight the need for circular plastic economy. Microorganisms have a great potential to enable a more sustainable plastic economy by biodegradation and enzymatic recycling of polymers. Temperature is a crucial parameter affecting biodegradation rates, but so far microbial plastic degradation has mostly been studied at temperatures above 20°C. Here, we isolated 34 cold-adapted microbial strains from the plastisphere using plastics buried in alpine and Arctic soils during laboratory incubations as well as plastics collected directly from Arctic terrestrial environments. We tested their ability to degrade, at 15°C, conventional polyethylene (PE) and the biodegradable plastics polyester-polyurethane (PUR; Impranil®); ecovio® and BI-OPL, two commercial plastic films made of polybutylene adipate-co-terephthalate (PBAT) and polylactic acid (PLA); pure PBAT; and pure PLA. Agar clearing tests indicated that 19 strains had the ability to degrade the dispersed PUR. Weight-loss analysis showed degradation of the polyester plastic films ecovio® and BI-OPL by 12 and 5 strains, respectively, whereas no strain was able to break down PE. NMR analysis revealed significant mass reduction of the PBAT and PLA components in the biodegradable plastic films by 8 and 7 strains, respectively. Co-hydrolysis experiments with a polymer-embedded fluorogenic probe revealed the potential of many strains to depolymerize PBAT. Neodevriesia and Lachnellula strains were able to degrade all the tested biodegradable plastic materials, making these strains especially promising for future applications. Further, the composition of the culturing medium strongly affected the microbial plastic degradation, with different strains having different optimal conditions. In our study we discovered many novel microbial taxa with the ability to break down biodegradable plastic films, dispersed PUR, and PBAT, providing a strong foundation to underline the role of biodegradable polymers in a circular plastic economy.

Effects of biodegradable and non-biodegradable microplastics on bacterial community and PAHs natural attenuation in agricultural soils

Anthropogenic activities such as in situ straw incineration and the widespread use of agricultural film led to the accumulation of polycyclic aromatic hydrocarbons (PAHs) and microplastics (MPs) in agricultural soils. In this study, four biodegradable MPs (BPs), including polylactic acid (PLA), polybutylene succinate (PBS), poly-β-hydroxybutyric acid (PHB) and poly (butylene adipate-co-terephthalate) (PBAT) and non-biodegradable low-density polyethylene (LDPE) were selected as representative MPs. The soil microcosm incubation experiment was conducted to analyze MPs effects on PAHs decay. MPs did not influence PAHs decay significantly on day 15 but showed different effects on day 30. BPs reduced PAHs decay rate from 82.4% to 75.0%- 80.2% with the order of PLA < PHB < PBS < PBAT while LDPE increased it to 87.2%. MPs altered beta diversity and impacted the functions to different extents, interfering in PAHs biodegradation. The abundance of most PAHs-degrading genes was increased by LDPE and decreased by BPs. Meanwhile, PAHs speciation was influenced with bioavailable fraction elevated by LDPE, PLA and PBAT. The facilitating effect of LDPE on 30-d PAHs decay can be attributed to the enhancement of PAHs-degrading genes and PAHs bioavailability, while the inhibitory effects of BPs were mainly due to the response of the soil bacterial community.

Biodegradable mulch films significantly affected rhizosphere microbial communities and increased peanut yield

Biodegradable mulch films are widely used to replace conventional plastic films in agricultural fields. However, their ecological effects on different microbial communities that naturally inhabit agricultural fields are scarcely explored. Herein, differences in bacterial communities recovered from biofilms, bulk soil, and rhizosphere soil were comparatively assessed for polyethylene film (PE) and biodegradable mulch film (BDM) application in peanut planted fields. The results showed that the plastic film type significantly influenced the bacterial community in different ecological niches of agricultural fields (P < 0.001). Specifically, BDMs significantly increased the diversity and abundance of bacteria in the rhizosphere soil. The bacterial communities in each ecological niche were distinguishable from each other; bacterial communities in the rhizosphere soil showed the most pronounced response among different treatments. Acidobacteria and Pseudomonas were significantly enriched in the rhizosphere soil when BDMs were used. BDMs also increased the rhizosphere soil bacterial network complexity and stability. The enrichment of beneficial bacteria in the rhizosphere soil under BDMs may also have implications for the observed increase in peanut yield. Deepening analyses indicated that Pseudoxanthomonas and Glutamicibacter are biomarkers in biofilms of PE and BDMs respectively. Our study provides new insights into the consequences of the application of different types of plastic films on microbial communities in different ecological niches of agricultural fields.

Enzymes' Power for Plastics Degradation

Plastics are everywhere in our modern way of living, and their production keeps increasing every year, causing major environmental concerns. Nowadays, the end-of-life management involves accumulation in landfills, incineration, and recycling to a lower extent. This ecological threat to the environment is inspiring alternative bio-based solutions for plastic waste treatment and recycling toward a circular economy. Over the past decade, considerable efforts have been made to degrade commodity plastics using biocatalytic approaches. Here, we provide a comprehensive review on the recent advances in enzyme-based biocatalysis and in the design of related biocatalytic processes to recycle or upcycle commodity plastics, including polyesters, polyamides, polyurethanes, and polyolefins. We also discuss scope and limitations, challenges, and opportunities of this field of research. An important message from this review is that polymer-assimilating enzymes are very likely part of the solution to reaching a circular plastic economy.

Mechanical Degradation of Polyethylene Plastic Film by Oxo-Degradable Additives

Utilizing oxo-degradable additives is an alternate, efficient method of managing plastic trash. To prepare the polymer chain for microorganisms to break down the fragments over time, oxo-degradation of plastics involves breaking the chain into small pieces. In this study, a film with a thickness of 35 µm is created by mixing a mixture of linear low-density polyethylene (LLDPE) and d2w grade master batch (pro-oxidant). This thickness falls within the range of specifications for linear low-density polyethylene (LLDPE) films manufactured in petrochemical businesses. Additionally, is the study investigates how the mechanical characteristics of linear low-density polyethylene (LLDPE) are affected by the addition of a d2w pro-oxidant additive at five different weight percentages (0, 0.5, 1, 2, and 3% w/w). After thermal processing for films in an oven for one to seven days, the progress of LLDPE film is monitored by FTIR analysis to check for the presence of the carbonyl group by assessing the mechanical properties of the film. Tensile strength at break, tensile strength at yield, elongation at break, and elongation at yield are the mechanical qualities that are measured. Both the machine direction (MD) and the transverse direction (TD) are used to measure all properties. Following seven days of exposure to the oven at 70 °C, the mechanical properties of the film deteriorated. Both in the machine and transverse directions (MD and TD), the tensile strength at break dropped by 46.62% and 31.8%, respectively. Both in the machine and transverse directions (MD and TD), the tensile strength at yield dropped by 22% and 36.36%, respectively. Both machine and transverse elongation at break (MD and TD) were reduced by 21% and 38.36%, respectively. Following the addition of pro-oxidant and after thermo-oxidative treatment in an oven at 70 °C for 7 days, the results of the FTIR measurement for LLDPE did not significantly alter.

Accelerated degradation of plastic products via yeast enzyme treatment

Biodegradable plastics can solve the problem of unwanted plastics accumulating in the environment if they can be given the contradictory properties of durability in use and rapid degradation after use. Commercially available agricultural biodegradable mulch films are made from formulations containing polybutylene adipate-co-terephthalate (PBAT) to provide mechanical and UV resistance during the growing season. Although used films are ploughed into the soil using a tiller to promote decomposition, it is difficult if they remain durable. We showed that an enzyme produced by the leaf surface yeast Pseudozyma antarctica (PaE) degrades PBAT-containing films. In laboratory studies, PaE randomly cleaved the PBAT polymer chain and induced erosion of the film surface. In the field, commercial biodegradable films containing PBAT placed on ridges were weakened in both the warm and cold seasons by spraying the culture filtrate of P. antarctica. After the field was ploughed the next day, the size and total weight of residual film fragments decreased significantly (p < 0.05). Durable biodegradable plastics used in the field are degraded using PaE treatment and are broken down into small fragments by the plough. The resultant degradation products can then be more readily assimilated by many soil microorganisms.

Plastic biodegradation by in vitro environmental microorganisms and in vivo gut microorganisms of insects

Traditional plastics, such as polyethylene (PE), polystyrene (PS), polypropylene (PP), polyvinyl chloride (PVC), polyethylene terephthalate (PET), polyurethane (PUR), and other plastic polymers, are difficult to degrade and are gradually accumulated in the environment to cause a serious environmental problem, which is urgently needed to develop novel treatments or control technology. The biodegradation of plastics has gained great attention due to the advantages of green and safe characteristics. Microorganisms play a vital role in the biodegradation of plastics, including environmental microbes (in vitro) and gut microbes of insects (in vivo). Microbial degradation in environmental conditions in vitro is extremely slow for major plastics at degradation rates on the basis of a month or even a year time, but recent discoveries show that the fast biodegradation of specific plastics, such as PS, PE, and PUR, in some invertebrates, especially insects, could be enhanced at rates on basis of hours; the biodegradation in insects is likely to be gut microbial-dependent or synergetic bioreactions in animal digestive systems. This review comprehensively summarizes the latest 7-year (2016-2022) publications on plastic biodegradation by insects and microorganisms, elucidates the mechanism of plastic degradation in insects and environmental microbes, and highlights the cutting-edge perspectives for the potential applications of plastic biodegradation.

An update on polyethylene and biodegradable plastic mulch films and their impact on the environment

Many ways are being developed in the realm of agriculture to increase crop yield while inflicting minimal damage to the soil and environment. One among them is the application of agricultural, biodegradable mulch (BDM) films. Organic substances or synthetic materials are used for making mulches. Also, bio-based polymers derived from bacteria, microorganisms, or fossil fuels are used to make BDM films. BDM films are used in crop production because of their high agronomical advantages which lead to sustainable agriculture. These films are placed on the soil's surface, around the plants. Mulches help in conserving the moisture, control the temperature of the soil, control the growth of the weed, and help in the utilization of soil nutrients thus, overall enhancing the crop yield. The usage of plastic mulch in agriculture has expanded substantially all around the world, over the past ten years, this is because polyethylene films are cheaper, easily produced, highly flexible, and durable. However, the improper disposal of used plastic films has resulted in soil pollution and environmental contamination. Traditional mulches are replaced by BDM, which is a more environmentally friendly alternative. After being used, degradable mulch films could be tilled into the soil and are expected to disintegrate over time. This review focuses on the BDMs, their history, plastic mulches, how BDMs became an alternative source for plastic mulches, their composition, and also addresses their significance. In addition, we discuss the environmental impact of films, including how it alters the climate, soil, temperature, and weed management.

Biodegradation of Biodegradable Polymers in Mesophilic Aerobic Environments

Finding alternatives to diminish plastic pollution has become one of the main challenges of modern life. A few alternatives have gained potential for a shift toward a more circular and sustainable relationship with plastics. Biodegradable polymers derived from bio- and fossil-based sources have emerged as one feasible alternative to overcome inconveniences associated with the use and disposal of non-biodegradable polymers. The biodegradation process depends on the environment's factors, microorganisms and associated enzymes, and the polymer properties, resulting in a plethora of parameters that create a complex process whereby biodegradation times and rates can vary immensely. This review aims to provide a background and a comprehensive, systematic, and critical overview of this complex process with a special focus on the mesophilic range. Activity toward depolymerization by extracellular enzymes, biofilm effect on the dynamic of the degradation process, CO2 evolution evaluating the extent of biodegradation, and metabolic pathways are discussed. Remarks and perspectives for potential future research are provided with a focus on the current knowledge gaps if the goal is to minimize the persistence of plastics across environments. Innovative approaches such as the addition of specific compounds to trigger depolymerization under particular conditions, biostimulation, bioaugmentation, and the addition of natural and/or modified enzymes are state-of-the-art methods that need faster development. Furthermore, methods must be connected to standards and techniques that fully track the biodegradation process. More transdisciplinary research within areas of polymer chemistry/processing and microbiology/biochemistry is needed.

Extraction of biodegradable microplastics from tissues of aquatic organisms

Biodegradable plastics (BPs) have been given high hopes to substitute conventional plastics, but their biodegradation requires strict conditions. BPs can accumulate for a long time in the environment and even derive biodegradable microplastics (BMPs), thus threatening wildlife and ecosystems. However, no efficient method is available for extracting BMPs from organisms' tissues. This study used multi-criteria decision-making (MCDM) methods to comprehensively evaluate and optimize extraction protocols of five BMPs from economic aquatic species. Digestion time, digestion efficiency, mass loss, cost, polymer integrity and size change were selected as evaluating indictors. According to the screening results of MCDM methods, Pepsin+H₂O₂ was selected as the optimal digestion method of BMPs because of its highest comprehensive score, which has high digestion efficiency (99.56%) and minimum plastic damage. Compared with olive oil, NaI is more suitable for separating BMPs from the digested residues. Furthermore, the combination of Pepsin+H₂O₂ digestion and NaI density separation was used to extract all five kinds of BMPs from the bivalve, crab, squid, and crayfish tissues, and all the recovery rates exceeded 80%. These results suggest that the optimal protocol is practicable to extract various BMPs from various aquatic organisms.

Microplastic presence significantly alters soil nitrogen transformation and decreases nitrogen bioavailability under contrasting temperatures

Plastic mulch is frequently used to increase crop yield, resulting in large quantities of residues accumulating in soil due to low recovery rates. However, the effects of microplastic residues from traditional and biodegradable plastic films on soil nitrogen (N) transformation and bioavailability are not well understood. Here, the main objectives were to examine the effects of micro-sized residues (diameter <5 mm) of polyethylene (PE) and biodegradable plastic mulch films (PLA) on the soil N in two contrasting soils (clay soil and sandy loam soil) in different temperatures (15 °C vs. 25 °C). Results showed that the microplastic presence showed a little effect on soil N transformation and bioavailability at 15 °C, but both microplastics significantly decreased NO₃^-, mineral N (MN), total dissolved N (TDN), the net cumulative N nitrification (Nn), and the net cumulative N mineralization (Nm) at 25 °C, indicating that microplastics decreased soil N bioavailability at elevated temperature. Meanwhile, the microplastics significantly reduced the temperature sensitivity (Q₁₀) of N mineralization. The presence of microplastics changed the composition of soil mineral N with lower relative NO₃^- and higher NH₄⁺ compared to the control in clay soil. The sandy loam soil was more susceptible to microplastic pollution compared to clay soil in N transformation, due to different textures and biochemistry properties in the two soils, which showed that microplastics have a significant soil heterogeneity-dependent effect on soil N processes. Therefore, the results underline that the effects of microplastic residues on soil N cycling can be partly linked to soil properties, suggesting the urgent need for further studies examining their impacts on soil nutrient cycling in different soil systems.

Succession of soil bacterial communities and network patterns in response to conventional and biodegradable microplastics: A microcosmic study in Mollisol

Significant soil contamination of microplastics (MPs) by the application of agricultural mulching films has aroused global concern, however, the effects of conventional and biodegradable MPs on the dynamics of soil microbial communities and network patterns have not been sufficiently reported. In this study, we conducted a soil microcosmic experiment by adding low-density polyethylene and biodegradable MPs (PE and BD) into a black soil at the dosages of 0 % (CK), 0.1 % (low-dose, w/w), 1 % (medium-dose, w/w) and 5 % (high-dose, w/w), and soils were sampled on the 15th, 30th, 60th and 90th day of soil incubation for high-throughput sequencing. The results showed that the incubation time was the most influential factor driving the variations in bacterial community structures, and significant effects of MP dosages and types were also detected. With the increase in MP dosage, bacterial diversity markedly increased and decreased at the beginning (D15) and end of sampling day (D90), respectively. Compared to CK, BD induced a larger community dissimilarity than PE and tended to enrich environmentally friendly taxa, while PE likely promoted the growth of hazardous taxa. Moreover, BD simplified interspecies interactions compared to the networks of PE and CK, and Nitrospira was identified as a keystone species in both PE and BD networks. These findings provide new insights into the influences of conventional and biodegradable MPs on the succession patterns of soil bacterial communities, and further studies are needed to explore the soil metabolic potentials affected by the presence of MPs.

Mulching as a Sustainable Water and Soil Saving Practice in Agriculture: A Review

This research was carried out in order to demonstrate that mulching the ground helps to conserve water, because agricultural sustainability in dryland contexts is threatened by drought, heat stress, and the injudicious use of scarce water during the cropping season by minimizing surface evaporation. Improving soil moisture conservation is an ongoing priority in crop outputs where water resources are restricted and controlled. One of the reasons for the desire to use less water in agriculture is the rising demand brought on by the world’s growing population. In this study, the use of organic or biodegradable mulches was dominated by organic materials, while inorganic mulches are mostly comprised of plastic-based components. Plastic film, crop straw, gravel, volcanic ash, rock pieces, sand, concrete, paper pellets, and livestock manures are among the materials put on the soil surface. Mulching has several essential applications, including reducing soil water loss and soil erosion, enriching soil fauna, and improving soil properties and nutrient cycling in the soil. It also reduces the pH of the soil, which improves nutrient availability. Mulching reduces soil deterioration by limiting runoff and soil loss, and it increases soil water availability by reducing evaporation, managing soil temperature, or reducing crop irrigation requirements. This review paper extensively discusses the benefits of organic or synthetic mulches for crop production, as well as the uses of mulching in soil and water conservation. As a result, it is very important for farmers to choose mulching rather than synthetic applications.

Influence of Calcium Carbonate Nanoparticles on the Soil Burial Degradation of Polybutyleneadipate-Co-Butylenetherephthalate Films

A polybutyleneadipate-co-butylenetherephthalate (PBAT) sample, commercially known as Ecoflex^®, was processed via melt extrusion with CaCO₃ nanoparticles coated with a hydrophobic coating. Blown films of PBAT and two composites with nanofiller (2% and 5%wt) were prepared and degradation tests in soil at 30 °C up to 180 days were carried out with weight loss measurements. Furthermore, biodegradation test according to ISO 14851 was carried out at 30 °C. The effect of CaCO₃ on soil burial degradation was assessed by surface wettability and SEM. ATR-FTIR and XPS analyses highlighted chemical modifications induced by soil degradation. CaCO₃ nanoparticles decreased surface wettability and discouraged the disintegration in soil. Interestingly, SEM images after soil degradation highlighted in the nanocomposite films selective zones of disintegration. XPS showed an increasing peak area C 1s ratio of C–O to C=O with degradation time. Moreover, after the soil burial test, carbonyl index determined by ATR-FTIR increased in both nanocomposites. In fact, the addition of CaCO₃ leads to a rise in the carbonyl zone due to the presence of the carbonate group. Remarkably, FTIR data after soil degradation showed an enrichment of the aromatic content, a preferential cleavage and erosion of the aliphatic moiety in PBAT films, amplified by the presence of the CaCO₃ nanofiller.

Closing the Carbon Loop in the Circular Plastics Economy

Today, plastics are ubiquitous in everyday life, problem solvers of modern technologies, and crucial for sustainable development. Yet the surge in global demand for plastics of the growing world population has triggered a tidal wave of plastic debris in the environment. Moving from a linear to a zero-waste and carbon-neutral circular plastic economy is vital for the future of the planet. Taming the plastic waste flood requires closing the carbon loop through plastic reuse, mechanical and molecular recycling, carbon capture, and use of the greenhouse gas carbon dioxide. In the quest for eco-friendly products, plastics do not need to be reinvented but tuned for reuse and recycling. Their full potential must be exploited regarding energy, resource, and eco efficiency, waste prevention, circular economy, climate change mitigation, and lowering environmental pollution. Biodegradation holds promise for composting and bio-feedstock recovery, but it is neither the Holy Grail of circular plastics economy nor a panacea for plastic littering. As an alternative to mechanical downcycling, molecular recycling enables both closed-loop recovery of virgin plastics and open-loop valorization, producing hydrogen, fuels, refinery feeds, lubricants, chemicals, and carbonaceous materials. Closing the carbon loop does not create a Perpetuum Mobile and requires renewable energy to achieve sustainability. This article is protected by copyright. All rights reserved.

Nanoarchitectonics for Biodegradable Superabsorbent Based on Carboxymethyl Starch and Chitosan Cross-Linked with Vanillin

Due to the growing demand for sustainable hygiene products (that will exhibit biodegradability and compostability properties), the challenge of developing a superabsorbent polymer that absorbs significant amounts of liquid has been raised so that it can be used in the hygiene sector in the future. The work covers the study of the swelling and dehydration kinetics of hydrogels formed by grafting polymerization of carboxymethyl starch (CMS) and chitosan (Ch). Vanillin (Van) was used as the crosslinking agent. The swelling and dehydration kinetics of the polymers were measured in various solutes including deionized water buffers with pH from 1 to 12 and in aqueous solutions of sodium chloride at 298 and 311 K. The surface morphology and texture properties of the analyzed hydrogels were observed by scanning electron microscopy (SEM). The influence of this structure on swelling and dehydration is discussed. Fourier transform infrared (FTIR) analyses confirmed the interaction between the carboxymethyl starch carbonyl groups and the chitosan amino groups in the resulting hydrogels. Additionally, spectroscopic analyses confirmed the formation of acetal crosslink bridges including vanillin molecules. The chemical dynamics studies revealed that new hydrogel dehydration kinetics strongly depend on the vanillin content. The main significance of the study concerns the positive results of the survey for the new superabsorbent polymer material, coupling high fluid absorbance with biodegradability. The studies on biodegradability indicated that resulting materials show good environmental degradability characteristics and can be considered true biodegradable superabsorbent polymers.

Biodegradation of PBSA Films by Elite Aspergillus Isolates and Farmland Soil

Plastic films are widely used in current agricultural practices; however, most mulch films used are discarded and buried in the land after harvest, having adverse environmental impacts. To solve this environmental problem, the demand for biodegradable mulch has been increasing in recent years. Polybutylene succinate-co-adipate (PBSA) is a biodegradable polymer with good ductility and can be used for packaging and mulching. In this study, we isolated two elite fungal strains for PBSA degradation from farmlands, i.e., Aspergillus fumigatus L30 and Aspergillus terreus HC, and the latter showed better degradation ability than the former. It is noteworthy that biodegradation of PBSA by A. terreus is reported for the first time, which revealed unique characteristics. In the soil burial test, even the soil with relatively poor degradation ability could be improved by the addition of elite fungal mycelia. In substrate specificity analyses of soil samples, PBSA could induce the synthesis of lipolytic enzymes of indigenous microbes to degrade substrates with medium and long carbon chains in soil. Furthermore, PBSA residues or fungal mycelia supplementation in soils had no adverse effect on the seed germination rate, seedling growth, or mature plant weight of the test green leafy vegetable. Taken together, the results of this study not only advance our understanding of the biodegradation of PBSA films by filamentous fungi but also provide insight into improving the efficiency of biodegradation in soil environments.

Field studies on the deterioration of microplastic films from ultra-thin compostable bags in soil

In recent years, some countries have replaced single-use plastic bags with bags manufactured from compostable plastic film that can be used for collecting food wastes and composted together with the waste. Because industrial compost contains undeteriorated fragments of these bags, application to field soil is a potential source of small-sized residues from these bags. This study was undertaken to examine deterioration of these compostable film microplastics (CFMPs) in field soil at three different localities in Italy. Deterioration of CFMPs did not exceed 5.7% surface area reduction during the 12-month experimental period in two sites located in Northern Italy. More deterioration was observed in the Southern site, with 7.2% surface area reduction. Deterioration was significantly increased when fields were amended with industrial compost (up to 9.6%), but not with home compost. Up to 92.9% of the recovered CFMPs were associated with the soil fungus Aspergillus flavus, with 20.1%-71.2% aflatoxin-producing isolates. Application of industrial compost resulted in a significant increase in the percentage of CFMPs associated with A. flavus. This observation provides an argument for government regulation of accumulation of CFMPs and elevation of hazardous fungi levels in agricultural soils that receive industrial compost.

Microbial communities on biodegradable plastics under different fertilization practices in farmland soil microcosms

Plastic mulching is a common practice in agricultural systems and is often combined with fertilization. Biodegradable plastics (BPs) are becoming an alternative to non-biodegradable plastics (non-BPs) for soil mulching. However, the effects of fertilization on the microbial communities on BPs remain unclear. Here, we explored the responses of the plastisphere to different fertilization practices in soil-based microcosms containing three BPs: polylactic acid (PLA), poly (butylene succinate) (PBS), and poly (butylene-adipate-co-terephthalate) (PBAT), and one non-BP (low-density polyethylene, LDPE). The 16S and ITS rRNA gene-based Illumina sequencing method were used to identify the bacterial and fungal communities on the plastics and in the soils. Microbial community structure on BPs was significantly different from that in soils and on LDPE. The predicted functional profiles of bacteria on BPs, especially PBAT, were distinct from those in soils. The plastisphere communities on BPs were dominated by microbes adapted to access and utilize carbon sources compared with of the communities on LDPE. Application of manure increased the alpha diversity of bacterial communities on BPs but decreased it on LDPE. The structure of bacterial communities on BPs changed with the application of manure. Our research establishes the baseline dynamics of plastisphere communities on BPs in soils.

Effects of biodegradable film mulching on bacterial diversity in soils

The spread of biodegradable plastic films (BDFs) not only increases grain yield but also reduces environmental pollution from plastic film to a large extent. Soil microbes are considered to be involved in biodegradation processes. However, the study of microbe diversity in soil mulched with biodegradable plastic film remains limited. Here, we compared the diversity of microbes between soils with biodegradable film and nonbiodegradable film (NBDF) mulch. The results showed that BDFs affected total C, P and NH₄⁺-N, especially organism C content, as well as microbe species richness (ACE; Chao1) and diversity (Simpson index; Shannon index). In terms of dominant phyla and genera, BDFs and NBDF can influence the abundance of disparate species. Furthermore, BDFs could also contribute to improving the richness of the important functional bacterial groups in soil, e.g., Pedomicrobium and Comamonas, both of which are involved in the degradation of plastic residues in soil. Finally, we found that BDFs improved the transformation of nitrogen by significantly increasing the abundances of Nitrobacter and Nitrospira. Our results highlight the impact of BDF mulch on the abundance of functional bacteria in the soil.

Milk Protein-Based Edible Films: Influence on Mechanical, Hydrodynamic, Optical and Antioxidant Properties

Edible films are thin preformed layers that provide food protection against adverse environmental conditions. Despite milk proteins being functional ingredients that can provide interesting features to films, there is scarce information evaluating their influence on film properties and stability. For this reason, this research work compared the mechanical (thickness, tensile strength, elongation at break), hydrodynamic (moisture content, water solubility, swelling ratio, water vapor transmission rate), color and antioxidant (DPPH) properties of edible films based on casein and whey protein isolate (two types, WPI1 and WPI2). Films with casein displayed the highest thickness (0.193 mm), elongation at break (49.67%), moisture content (40.21%) and antioxidant capacity (32.64% of DPPH inhibition), while obtaining the lowest water vapor transmission rate (15.28 g/m2·day). Significant differences were found in the color properties, mainly between films with casein and those made with WPI. Films containing WPI1 and WPI2 were statistically similar in thickness, tensile strength and color properties. The results showed that the properties of the edible films depended on the type of milk protein used. Thus, it is important to evaluate the features provided by different ingredients and formulations for obtaining edible films that properly preserve food.

Design, Simulation and Experimentation of a Polythene Film Debris Recovery Machine in Soil

With the rapid development of planting techniques using plastic film mulching, the content of residual plastic film in soil increases year by year, which pollutes the soil and water, endangers the growth of crops and reduces the quality and yield of agricultural products. Therefore, in order to solve the problem that plastic film with a thickness of 0.008 mm, commonly used in China, is difficult to recycle, this study designed the residue film recycling machine based on the existing research results. After harvesting cotton in Xinjiang, the working performance of the residue film recovery machine of plough layer was measured. Through theoretical optimization and field experiments, the effects of conveyor speed, distance between elastic teeth and type of elastic teeth on residual film recovery were studied. The relationship between the parameters of the residual film recovery machine and the recovery effect of the residual film was analyzed. When the rotational speed and inclination angle of the conveying and separating device were 74 rpm, 35° and 120 rpm, 45°, respectively, under the condition that the distance between C-shaped elastic teeth was 59 mm, the recovery and separation rate of residual plastic film were 88.12% and 83.27%, respectively. Based on the study results, it is recommended to accelerate the development of naturally degradable agricultural plastic film or to popularize and apply thickened film. Relevant local standards and policies have been formulated to address the problem of residual film pollution, and a governance system has been established for the benefit of the government, scientific research institutions, enterprises and farmers. This study provides a reference for mechanized recovery of residual plastic film in soil and treatment of soil pollution.

Microplastics in the soil-groundwater environment: Aging, migration, and co-transport of contaminants - A critical review

Microplastic contamination in soil has received increasing attention since excessive plastic debris has been emitted directly into the terrestrial environment. Once released into the terrestrial environment, microplastics can be aged via photo- and thermally-initiated oxidative degradation, hetero-aggregation, and bioturbation. Aging affects the physiochemical properties of microplastics with the increase of surface roughness and oxygen-containing groups, which could enhance the sorption and mobility of microplastics in the soil and groundwater environment. However, the interactions among aging, sorption, and transport of microplastics in the terrestrial system have not been unveiled. This review clarifies the key processes of microplastics transport pathways in soil and groundwater ecosystems influenced by aging and sorption under various scenarios. Co-transport of microplastics and sorbed contaminants are also addressed to help understand the risks associated with heavy metals, organic contaminants, and engineered nanoparticles in the soil environment. Overall, this review elaborates the most pressing research limitations on the present literature and highlights the future perspectives to investigate the possible broad transport pathways of microplastics in soil.

Fate of plastic film residues in agro-ecosystem and its effects on aggregate-associated soil carbon and nitrogen stocks

Biodegradable (Bio) plastic films are widely viewed as promising alternative products of low-density polyethylene (LDPE) films to minimize plastic debris accumulation and pollution in agroecosystems. Yet, this speculation indeed lacks of sufficient evidences. We conducted a landfill investigation on the aging characteristics of Bio and LDPE plastic films in maize field, and the effects on soil aggregate composition and carbon & nitrogen stocks. The degradation rate of Bio film was up to 41.1% while that of LDPE film was zero. Scanning electron microscope (SEM) showed that the crack formation of Bio film had a pronounced domino effect, and FTIR showed that old Bio film displayed an extra wide peak threshold ranging from 3000 to 3500 cm^-1. Particularly, the abundance of microplastics was elevated with the increased plastic residues, and the increment mostly resulted from Bio residues. Critically, plastic residues significantly lowered the soil macro-aggregates (>0.25 mm) proportion, while increasing that of micro-aggregates (0.1-0.25 mm) in LDPE, and silt/clay fraction (<0.1 mm) in Bio respectively. They significantly promoted total nitrogen content of the aggregates with the same size, but decreased the organic carbon content, dramatically lowering the C/N. Therefore, we first identified the fate of plastic film residues in agroecosystems and revealed the serious deficiencies of Bio plastic film.

Mechanistic aspects of poly(ethylene terephthalate) recycling-toward enabling high quality sustainability decisions in waste management

Since plastic waste pollution is a severe environmental concern in modern life, the demand for recycling poly(ethylene terephthalate) (PET) has increased due to its versatile applications. Taking advantage of plastic recycling methods creates the chances of minimizing overall crude oil-based materials consumption, and as a result, greenhouse gasses, specifically CO₂, will be decreased. Although many review articles have been published on plastic recycling methods from different aspects, a few review articles exist to investigate the organic reaction mechanism in plastic recycling. This review aims to describe other processes for recycling bottle waste of PET, considering the reaction mechanism. Understanding the reaction mechanism offers practical solutions toward protecting the environment against disadvantageous outgrowths rising from PET wastes. PET recycling aims to transform into a monomer/oligomer to produce new materials from plastic wastes. It is an application in various fields, including the food and beverage industry, packaging, and textile applications, to protect the environment from contamination and introduce a green demand for the near future. In this review, the chemical glycolysis process as an outstanding recycling technique for PET is also discussed, emphasizing the catalysts' performance, reaction conditions and methods, degradation agents, the kinetics of reactions, and reprocessing products. In general, a correct understanding of the PET recycling reaction mechanism leads to making the right decisions in waste management.

Microplastics disrupt accurate soil organic carbon measurement based on chemical oxidation method

Microplastics are widespread contaminants in soils and terrestrial ecosystems in many areas worldwide. In this study, we measured soil organic carbon (SOC) and soil organic matter (SOM) in microplastic-treated soils to determine if the presence of microplastics could affect the accuracy of carbon-based soil quality indicator measurements. Six different sizes and types of microplastics were selected, and six soil samples were used to evaluate the impacts. Treating soil with polyethylene and low-density polyethylene significantly increased SOC (p < 0.05) when measured with the modified Walkley & Black method; microplastic addition (0.01%, v/v) increased SOC by >40% compared to control organic carbon-poor soil (<10.0 g kg^-1). We conclude that the microplastics can disrupt the accurate measurement of SOC. Likely, the physicochemical treatment used in the SOC measurement process can cause the organic compounds and/or carbon complexes to be extracted from microplastics, and this can affect the results. Considering that SOC is a main indicator for assessing soil quality and the global carbon cycle, overestimations caused by microplastic contamination should be further discussed to identify appropriate ways to deal with microplastics as a new carbon source in the environment.