Contaminants of emerging concern: a review of new approach in AOP technologies

In situ remediation of oil-contaminated soils by ozonation: Experimental study and numerical modeling

The goal of the present work is to quantify the performance of ozonation as a method for the in situ remediation of soils polluted at varying degree with different types of hydrocarbons, and assess its applicability, in terms of remediation efficiency, cost factors, and environmental impacts. Ozonation tests are conducted on dry soil beds, for three specific cases: sandy soil contaminated with low, moderate and high concentration of a non-aqueous phase liquid (NAPL) consisting of equal concentrations of n-decane, n-dodecane, and n-hexadecane; sandy soil polluted with diesel fuel; oil-drilling cuttings (ODC). The transient changes of the concentration of the total organic carbon (TOC), total petroleum hydrocarbons (TPH), polycyclic aromatic hydrocarbons (PAHs), and soluble chemical oxygen demand (SCOD) in soil and carbon dioxide (CO2), carbon monoxide (CO), volatile organic compounds (VOCs), and ozone (O3) in exhaust gases are recorded. A numerical model is suggested where the ozone is adsorbed on solid grains, reacts with adsorbed organic species, and desorbed CO2, CO along with unconsumed O3 are released. The model is used to estimate the ozonation kinetic parameters, upscale the process, and estimate the cost and gas emissions per 1 tn of treated soil. Experiments reveal that after 4h of treatment, the TOC decreases profoundly only for the low NAPL concentration (76.4%), the highest and fastest TPH removal efficiency occurs for the moderate NAPL concentration (∼88%), and diesel fuel (87%), while the TPH removal efficiency becomes high enough for oil-drilling cuttings (80%) after 8h of treatment. In all cases, mainly CO2 is detected in exhaust gases, its cumulative mass is fully consistent with the TOC losses, while the O3 consumption is enhanced for heavily polluted soils. The concentration of PAHs is reduced profoundly for both the diesel fuel and ODC. The lowest energy consumption per unit mass of degraded TPH or TOC occurs for the heavily polluted soils. The cost of soil treatment increases with the initial TPH concentration and pollutant complexity increasing.

Removal efficiencies for 52 pesticides and pharmaceuticals from wastewater effluent by coupling solar heterogeneous photo-oxidation with TiO2 and infiltration in saturated soil column

Water resource management has become a hot button issue in recent decades. Countries facing water shortages as a result to climate change must adapt their water supply. The reuse of wastewater treatment plant effluents is becoming increasingly common around the world. However, the effluent quality must be improved before its reutilization to avoid contamination of the receiving environment. Pharmaceuticals and pesticides are particularly monitored because of their ubiquitous behaviours and limited removal by conventional wastewater treatment plants. The aim of this study was to combine heterogeneous photo-oxidation with TiO2 and soil infiltration to increase the elimination of contaminants of emerging concern (CECs). These advanced treatments were applied on an effluent coming from a WWTP equipped with a Ultrafor membrane bioreactor (sludge ages: 8-30 days, biomass concentration: 8-12 g.L-1, hydraulic retention: 6.7-8 h). The concentration of CECs was determined to evaluate the efficiency of coupling treatments. Photo-oxidation alone showed an impressive 98 % removal under spring conditions, while 66 % removal was observed under winter conditions. The differences observed for photo-oxidation were related to UV flux density, lower in winter than in spring (4.4 kJ.L-1 vs 6.6 kJ.L-1) and initial concentrations of the effluent higher in winter (50 μg.L-1 vs 26 μg.L-1). For both experiments, additional soil infiltration increased the global concentration of CECs removal to at least 89 % with equal removal contributions observed for some compounds. From the 52 CECs quantified in the WWTP effluent, at least 30 were totally removed by the advanced treatments while 4 compounds showed recalcitrant behaviours with global removal <60 %.

Mechanochemical remediation of contaminated soil: A review

Mechanochemical techniques have been garnering growing attention in remediation of contaminated soil. This paper summarizes the performance, mechanism, influential factors, and environmental impacts of mechanochemical remediation (MCR) for persistent organic pollutants (POPs) contaminated soil and heavy metal(loid) s (HMs) contaminated soil. Firstly, in contrast to other technologies, MCR can achieve desirable treatment of POPs, HMs, and co-contaminated soil, especially with high-concentration pollutants. Secondly, POPs undergo mineralization via interaction with mechanically activated substances, where aromatic and aliphatic pollutants in soil may go through varied degradation routes; inorganic pollutants can be firmly combined with soil particles by fragmentation and agglomeration induced by mechanical power, during which additives may enhance the combination but their contact with anionic metal(loid)s may be partially suppressed. Thirdly, the effect of MCR primarily hinges on types of milling systems, the accumulation of mechanical energy, and the use of reagents, which is basically regulated through operating parameters: rotation speed, ball-to-powder ratio, reagent-to-soil ratio, milling time, and soil treatment capacity; minerals like clay, metal oxides, and sand in soil itself are feasible reagents for remediation, and alien additives play a crucial role in synergist and detoxification; additionally, various physicochemical properties of soil might influence the mechanochemical effect to varying degrees, yet the key influential performance and mechanism remain unclear and require further investigation. Concerning the assessment of soil after treatment, attention needs to be paid to soil properties, toxicity of POPs' intermediates and leaching HMs, and long-term appraisement, particularly with the introduction of aggressive additives into the system. Finally, proposals for current issues and forthcoming advancements in this domain are enumerated in items. This review provides valuable insight into mechanochemical approaches for performing more effective and eco-friendly remediation on contaminated soil.

Microbial degradation of contaminants of emerging concern: metabolic, genetic and omics insights for enhanced bioremediation

The perpetual release of natural/synthetic pollutants into the environment poses major risks to ecological balance and human health. Amongst these, contaminants of emerging concern (CECs) are characterized by their recent introduction/detection in various niches, thereby causing significant hazards and necessitating their removal. Pharmaceuticals, plasticizers, cyanotoxins and emerging pesticides are major groups of CECs that are highly toxic and found to occur in various compartments of the biosphere. The sources of these compounds can be multipartite including industrial discharge, improper disposal, excretion of unmetabolized residues, eutrophication etc., while their fate and persistence are determined by factors such as physico-chemical properties, environmental conditions, biodegradability and hydrological factors. The resultant exposure of these compounds to microbiota has imposed a selection pressure and resulted in evolution of metabolic pathways for their biotransformation and/or utilization as sole source of carbon and energy. Such microbial degradation phenotype can be exploited to clean-up CECs from the environment, offering a cost-effective and eco-friendly alternative to abiotic methods of removal, thereby mitigating their toxicity. However, efficient bioprocess development for bioremediation strategies requires extensive understanding of individual components such as pathway gene clusters, proteins/enzymes, metabolites and associated regulatory mechanisms. "Omics" and "Meta-omics" techniques aid in providing crucial insights into the complex interactions and functions of these components as well as microbial community, enabling more effective and targeted bioremediation. Aside from natural isolates, metabolic engineering approaches employ the application of genetic engineering to enhance metabolic diversity and degradation rates. The integration of omics data will further aid in developing systemic-level bioremediation and metabolic engineering strategies, thereby optimising the clean-up process. This review describes bacterial catabolic pathways, genetics, and application of omics and metabolic engineering for bioremediation of four major groups of CECs: pharmaceuticals, plasticizers, cyanotoxins, and emerging pesticides.

Ecological impacts and management strategies of pesticide pollution on aquatic life and human beings

Pesticide contamination has become a global concern. Pesticides can sorb onto suspended particles and deposit into the sedimentary layers of aquatic environments, resulting in ecosystem degradation, pollution, and diseases. Pesticides impact the behavior of aquatic environments by contaminating organic matter in water, which serves as the primary food source for aquatic food webs. Pesticide residues can increase ammonium, nitrite, nitrate, and sulfate in aquatic systems; thus, threatening ecological environment and human health. Several physical, chemical, and biological methodologies have been implemented to effectively remove pesticide traces from aquatic environments. The present review highlights the potential consequences of pesticide exposure on fish and humans, focusing on the (epi)genetic alterations affecting growth, behavior, and immune system. Mitigation strategies (e.g., bioremediation) to prevent/minimize the detrimental impacts of pesticides are also discussed. This review aims to shed light on the awareness in reducing the risk of water pollution for safe and sustainable pesticide management.

Factors in the decline of the African penguin: Are contaminants of emerging concern (CECs) a potential new age stressor?

The African penguin is currently experiencing a significant decline, with just over 10,000 breeding pairs left. A substantial body of research reflects the impacts of contaminants of emerging concern (CECs) on the marine environment, with wastewater treatment plants reported as one of the main sources of CEC release. In South Africa, CECs were identified contaminating the marine environment and bioaccumulating in several marine species. Approximately 70 % of all African penguin colonies breed in close proximity to cities and/or harbors in South Africa. Currently, the impact of CECs as a stressor upon the viability of African penguin populations is unknown. Based on the search results there was a clear lack of information on CECs' bioaccumulation and impact on the African penguin. This narrative review will thus focus on the prevalent sources and types of CECs and examine the reported consequences of constant exposure in seabirds, particularly African penguins.

Optimization of TiO2-natural hydrogels for paracetamol and ibuprofen degradation in wastewaters

Agarose/micrometer titanium dioxide (TiO2) beads were essayed to test the photocatalytic capacity of two of the most widely prescribed drugs worldwide: paracetamol and ibuprofen. Although the initial tests demonstrated promising degradation rates for both drugs, the presence of turbidity, due to TiO2 leakage, during the photocatalytic essays induced to improve the stability of the photocatalytic composites. Among the different strategies adopted to strengthen such materials, crosslinking with citric acid and the use of alternative gelling agents: gellan, agargel™, and agar were chosen. Composites obtained by merging both strategies were characterized and employed to degrade both drugs under a simulated light that mimics the solar spectrum (indoor). Considering the superior degradation rates obtained when agar and agarose were used to shape the titanium oxide particles (up to 70-75% of drug destruction), such composites were subjected to a more realistic experiment (outdoor): solar illumination, tap water, and higher volumes, that should facilitate its ulterior scale up as a real wastewater depollution procedure. Degradation rates between 80 and 90% are attained under such conditions for both drugs.

Ultraviolet activation of monochloramine to treat contaminants of emerging concern: reactions, operating parameters, byproducts, and opportunities

The presence of CECs in aquatic systems has raised significant concern since they are potentially harmful to the environment and human health. Eliminating CECs has led to the development of alternatives to treat wastewater, such as advanced oxidation processes (AOPs). The ultraviolet-mediated activation of monochloramine (UV/NH2Cl) is a novel and relatively unexplored AOPs for treating pollutants in wastewater systems. This process involves the production of amino radicals (•NH2) and chlorine radicals (Cl•) from the UV irradiation of NH2Cl. Studies have demonstrated its effectiveness in mitigating various CECs, exhibiting advantages, such as the potential to control the amount of toxic disinfection byproducts (TDBPs) formed, low costs of reagents, and low energy consumption. However, the strong influence of operating parameters in the degradation efficiency and existence of NH2Cl, the lack of studies of its use in real matrices and techno-economic assessments, low selectivity, and prolonged treatment periods must be overcome to make this technology more competitive with more mature AOPs. This review article revisits the state-of-the-art of the UV/NH2Cl technology to eliminate pharmaceutical and personal care products (PPCPs), micropollutants from the food industry, pesticides, and industrial products in aqueous media. The reactions involved in the production of radicals and the influence of operating parameters are covered to understand the formation of TDBPs and the main challenges and limitations of the UV/NH2Cl to degrade CECs. This review article generates critical knowledge about the UV/NH2Cl process, expanding the horizon for a better application of this technology in treating water contaminated with CECs.

Photocatalytic Degradation of Naproxen: Intermediates and Total Reaction Mechanism

Photochemical and photocatalytic oxidation of naproxen (NPX) with UV-A light and commercial TiO2 under constant flow of oxygen have been investigated. Adsorption experiments indicated that 90% of the solute remained in the solution. Combined chemical analysis of samples on the photochemical degradation indicated that NPX in an aqueous solution (20 ppm) is efficiently transformed into other species but only 18% of the reactant is mineralized into CO2 and water after three hours of reaction. Performing the photocatalytic oxidation in the presence of TiO2, more than 80% of the organic compounds are mineralized by reactive oxidation species (ROS) within four hours of reaction. Analysis of reaction mixtures by a combination of analytical techniques indicated that naproxen is transformed into several aromatic naphthalene derivatives. These latter compounds are eventually transformed into polyhydroxylated aromatic compounds that are strongly adsorbed onto the TiO2 surface and are quickly oxidized into low-molecular-weight acids by an electron transfer mechanism. Based on this and previous studies on NPX photocatalytic oxidation, a unified and complete degradation mechanism is presented.

Development of dissolved organic matter-based indicators to understand the degradation of organic contaminants in reverse osmosis concentrate from potable reuse systems

Reverse osmosis (RO)-based treatment of municipal wastewater effluent allows for potable reuse, but this process generates reverse osmosis concentrate (ROC) that needs further treatment before disposal. This study investigated the application of UV-based advanced oxidation processes (AOPs) to degrade nine contaminants of emerging concern (CECs) from real ROC waste streams, using UV-only and UV-AOPs with hydrogen peroxide, free chlorine, and persulfate. Dissolved organic matter (DOM) in ROC was characterized using fluorescence excitation emission matrix data and analyzed by a four-component parallel factor (PARAFAC) analysis model. UV-only treatment showed considerable removal of CECs that displayed high values of quantum yields and molar absorption coefficients. UV-AOP treatment of ROC exhibited heavy scavenging of reactive species during CEC degradation. A probe-based approach established that hydroxyl radical was the dominant reactive species in all UV-AOPs. A kinetic analysis of PARAFAC components of DOM showed that the visible humic-like and protein-like components exhibited the higher reaction kinetics compared to UV humic-like and nutrient-like components. The strong linear correlation of protein-like component and seven of the nine CECs across multiple AOPs indicated that they have similar reactivity, enabling the establishment of chemical-reactivity based surrogates for prediction CEC fate in ROC wastes.

Solvothermally Grown Oriented WO3 Nanoflakes for the Photocatalytic Degradation of Pharmaceuticals in a Flow Reactor

Contamination by pharmaceuticals adversely affects the quality of natural water, causing environmental and health concerns. In this study, target drugs (oxazepam, OZ, 17-α-ethinylestradiol, EE2, and drospirenone, DRO), which have been extensively detected in the effluents of WWTPs over the past decades, were selected. We report here a new photoactive system, operating under visible light, capable of degrading EE2, OZ and DRO in water. The photocatalytic system comprised glass spheres coated with nanostructured, solvothermally treated WO3 that improves the ease of handling of the photocatalyst and allows for the implementation of a continuous flow process. The photocatalytic system based on solvothermal WO3 shows much better results in terms of photocurrent generation and photocatalyst stability with respect to state-of-the-art WO3 nanoparticles. Results herein obtained demonstrate that the proposed flow system is a promising prototype for enhanced contaminant degradation exploiting advanced oxidation processes.

Alps at risk: High-mountain lakes as reservoirs of persistent and emerging contaminants

Despite their remote locations, high-mountain lakes located in the Alps are vulnerable to chemical pollution. This discussion explores the important aspects of these lakes as repositories of Persistent Organic Pollutants (POPs) and Contaminants of Emerging Concern (CECs), elucidating their sources and implications for both the environment and human health. In terms of the presence of POPs in high-altitude lakes of the Alps, 14 studies have been identified examining the occurrence of polychlorinated biphenyls, dichlorodiphenyltrichloroethane an its metabolites, polybrominated diphenyl ethers, and polycyclic aromatic hydrocarbons. The bulk of research on POPs in high-mountain lakes is concentrated in the Italian Alps (63%), followed by Switzerland (22%), Austria (12%), and France (3%), respectively. Sediment is predominantly investigated (65%), followed by fish (33%) and water (2%). Similarly, in relation to the presence of CECs in high-mountain lakes of the Alps, six studies have been identified investigating the occurrence of musks, perfluorinated compounds, and microplastics. Investigations into CECs predominantly occur in Switzerland (42%), France (33%), and Italy (25%), with fish samples (muscle and liver) being the primary focus (46%), followed by sediment (17%) and water (17%). Other compartments like zooplankton, frog/tadpoles, and snow remain less explored. The discussion also shed light on various pathways through which pollutants reach these remote landscapes, including atmospheric transport, glacial meltwater, and human activities. Protecting these pristine peaks demands concerted efforts encompassing ongoing research, vigilant monitoring, and dedicated conservation initiatives.

Assessment of new hydrogen peroxide activators in water and comparison of their active species toward contaminants of emerging concern

Advanced oxidation processes are the most efficient tool to thwart the overaccumulation of harmful organic compounds in the environment. In this direction bioinspired metal complexes may be a viable solution for oxidative degradations in water. However, their synthesis is often elaborated and their scalability consequently low. This study presents alternative easy-to-synthesize bioinspired metal complexes to promote degradations in water. The metals employed were iron and manganese ions, hence cheap and highly accessible ions. The complexes were tested toward Phenol, Estrone, Triclosan, Oxybenzone, Diclofenac, Carbamazepine, Erythromycin, Aspartame, Acesulfame K, Anisole and 2,4-Dinitrotoluene. The reaction favoured electron-rich compounds reaching a removal efficiency of over 90%. The central ion plays a crucial role. Specifically, Mn(II) induces a non-radical pathway while iron ions a predominant radical one (⋅OH is predominant). The iron systems resulted more versatile toward contaminants, while the manganese ones showed a higher turn-over number, hence higher catalytic behaviour.

Metagenomic insights into the toxicity of carbamazepine to functional microorganisms in sludge anaerobic digestion

Contaminants of emerging concern (CECs) contained in sludge, such as carbamazepine, may be toxic to microorganisms and affect the biogenesis of methane during anaerobic digestion. In this study, different scales of anaerobic digesters were constructed to investigate the inhibitory effect of carbamazepine. Results showed that carbamazepine reduced methane production by 11.3 % and 62.1 % at concentrations of 0.4 and 2 mg/g TS, respectively. Carbamazepine hindered the dissolution of organic matter and the degradation of protein. Carbamazepine inhibited some fermentative bacteria, especially uncultured Aminicenantales, whose abundance decreased by 9.5-93.4 % under carbamazepine stress. It is worth noting that most prior studies investigated the effects of CECs only based on well-known microorganisms, ignoring the metabolisms of uncultured microorganisms. Genome-predicted metabolic potential suggested that 54 uncultured metagenome-assembled genomes (MAGs) associated with acidogenesis or acetogenesis. Therein, uncultured Aminicenantales related MAGs were proved to be acetogenic fermenters, their significant reduction may be an important reason for the decrease of methane production under carbamazepine stress. The toxicity of carbamazepine to microorganisms was mainly related to the overproduction of reactive oxygen species. This study elucidates the inhibition mechanism of carbamazepine and emphasizes the indispensable role of uncultured microorganisms in anaerobic digestion.

Study on diazinon toxicity reduction by electro-Fenton process: A bioassay using daphnia magna

The realm of diazinon reduction from polluted water has witnessed a surge in the significance of advanced oxidation processes (AOPs) in recent times. However, there is a dearth of research focusing on the mitigation of its toxicity through AOPs. Thus, the primary objective of this study was to evaluate the effectiveness of the Electro-Fenton process (EFP) in the eradication and detoxification of diazinon in aqueous solutions. Synthetic wastewater samples with concentrations of 2, 2.5 and 3 mg/L were prepared. A total of 27 samples were determined using Box Behnken Design. Reaction time, pH and iron to hydrogen peroxide ratio (Fe2+/H2O2) were examined as operational parameters under a constant current of 5.4 amps. The quantification of diazinon concentration was performed using High-Performance Liquid Chromatography (HPLC). To evaluate the detoxification of diazinon, the Daphnia magna bioassay was employed as a methodology in this study. According to the results, the EFP could reduce the diazinon to zero and the LC50 values are increased by applying the process. The LC50 values for diazinon were determined using the Daphnia magna bioassay, considering initial concentrations of 2, 2.5, and 3 mg/L at a pH of 5, a reaction time of 15 min, and an iron to hydrogen peroxide molar ratio of 2. The recorded LC50 values were 3.039, 3.076, and 3.106, respectively, indicating the lowest frequency of cumulative death in Daphnia magna. In this case, after 96 h, only 3 cases (30%) of Daphnia magna death were observed. However, for all the mentioned concentrations of diazinon, after 96 h of exposure to samples without applying the Daphnia Magna death process, it was observed between 60 and 100%. Reducing the diazinon concentration and increasing the 96-h LC50 showed that the EFP can reduce the toxicity of diazinon on Daphnia Magna at the same time. Therefore, EFP can be considered a superior method with low ecotoxicity.

Recent advances in remediation strategies for mitigating the impacts of emerging pollutants in water and ensuring environmental sustainability

The proliferation of emerging pollutants (EPs), encompassing a range of substances such as phthalates, phenolics, pharmaceuticals, pesticides, personal care products, surfactants, and disinfection agents, has become a significant global concern due to their potential risks to the environment and human well-being. Over the past two decades, numerous research studies have investigated the presence of EPs in wastewater and aquatic ecosystems, with the United States Environmental Protection Agency (USEPA) categorizing these newly introduced chemical compounds as emerging contaminants due to their poorly understood impact. EPs have been linked to adverse health effects in humans, including genotoxic and cytotoxic effects, as well as conditions such as obesity, diabetes, cardiovascular disease, and reproductive abnormalities, often associated with their estrogenic action. Microalgae have shown promise in the detoxification of both inorganic and organic contaminants, and several large-scale microalgal systems for wastewater treatment have been developed. However, the progress of algal bioremediation can be influenced by accidental contaminations and operational challenges encountered in pilot-scale research. Microalgae employ various processes, such as bioadsorption, biouptake, and biodegradation, to effectively remediate EPs. During microalgal biodegradation, complex chemical compounds are transformed into simpler substances through catalytic metabolic degradation. Integrating algal bioremediation with existing treatment methodologies offers a viable approach for efficiently eliminating EPs from wastewater. This review focuses on the use of algal-based biological remediation processes for wastewater treatment, the environmental impacts of EPs, and the challenges associated with implementing algal bioremediation systems to effectively remove emerging pollutants.

Ginkgo biloba extract protects against tartrazine-induced testicular toxicity in rats: involvement of antioxidant, anti-inflammatory, and anti-apoptotic mechanisms

The use of additives, especially colorants, in food and pharmaceutical industry is increasing dramatically. Currently, additives are classified as contaminants of emerging concern (CECs). Concerns have been raised about the potential hazards of food additives to reproductive organs and fertility. The present study investigates the reproductive toxicity of tartrazine (TRZ), a synthetic colorant, in male rats and aims to explore the curative effect of Ginkgo biloba extract (EGb) against TRZ-induced testicular toxicity. Twenty-four rats were divided into four groups: the control (0.5 ml distilled water), the EGb group (100 mg/kg EGb alone), the TRZ group (7.5 mg/kg TRZ alone), and the TRZ-EGb group (7.5 mg/kg TRZ plus 100 mg/kg EGb). The doses were administered orally in distilled water once daily for 28 days. Toxicity studies of TRZ investigated testicular redox state, serum gonadotropins, and testosterone levels, testicular 17 ß-hydroxysteroid dehydrogenase activity, sperm count and quality, levels of inflammatory cytokines, and caspase-3 expression as an apoptotic marker. Also, histopathological alterations of the testes were examined. TRZ significantly affected the testicular redox status as indicated by the increase in malondialdehyde and the decrease in reduced glutathione, superoxide dismutase, and catalase. It also disrupted serum gonadotropins (follicle stimulating hormone and luteinizing hormone) and testosterone levels and the activity of testicular 17ß-hydroxysteroid dehydrogenase. Additionally, TRZ adversely affected sperm count, motility, viability, and abnormality. Levels of tumor necrosis factor-α, interleukin-1β, interleukin-6, and expression of caspase-3 were increased in the testes. Histopathological examination of the testes supported the alterations mentioned above. Administration of EGb significantly ameliorated TRZ-induced testicular toxicity in rats. In conclusion, EGb protected against TRZ-induced testicular toxicity through antioxidant, anti-inflammatory, and anti-apoptotic mechanisms.

The seasonality of the concentration of endocrine phenolic compounds in the matter attached to the surface of microplastics

Rapid biofilm formation on microplastic (MP) surfaces in marine environments and the tendency of hydrophobic pollutants to bioaccumulate may increase the exposure of organisms to ingested plastics and transport pollutants far from their sources. The role of the matter attached to MPs (MaM) in the interactions between MPs and other pollutants in marine environments is poorly understood. This paper studies pollutant sorption in MaM for three phenolic endocrine-disrupting chemicals (EDCs): bisphenol A (BPA), 4-tert-octylphenol (4-t-OP), and 4-nonylphenol (4-NP). Polypropylene (PP), expanded polystyrene (EPS), and polylactide (PLA) MPs were exposed to an environment conducive to biofouling (Vistula Lagoon, Baltic Sea) for four weeks in summer, spring, and winter. The concentrations of EDCs in MaM and the suspended particulate matter (SPM) were similar and were 2-3 orders of magnitude higher than those in water and sediment. The type and morphology of the polymers were less significant for determining the concentrations of EDCs in MaM than the season. The concentrations were higher in the growing season than in winter. EDCs increased linearly with the increase in particulate organic carbon. The relationships between organic carbon partition coefficients and octanol/water partition coefficients indicate that hydrophobic partitioning into organic matter was the dominant mechanism of 4-t-OP and 4-NP binding in MaM and in SPM. For BPA, additional sorption mechanisms seem to be significant. In addition to the direct sorption from ambient water, the binding of phytoplankton-derived particles, most probably via attachment to extracellular polymeric substances, appears to be a source of EDCs in MPs. Rough estimates showed that the largest load of particulate matter and EDCs was attached to expanded polystyrene. This study suggests that the potential negative impacts of MPs on the environment are seasonal and that low-density porous plastics can be particularly effective carriers of large EDC loads.

Recent progress in mineralization of emerging contaminants by advanced oxidation process: A review

Emerging contaminants are chemicals generated due to the usage of pesticide, endocrine disrupting compounds, pharmaceuticals, and personal care products and are liberated into the environment in trace quantities. The emerging contaminants eventually become a greater menace to living beings owing to their wide range and inhibitory action. To diminish these emerging contaminants from the environment, an Advanced Oxidation Process was considered as an efficient option. The Advanced Oxidation Process is an efficient method for mineralizing fractional or generous contaminants due to the generation of reactive species. The primary aim of this review paper is to provide a thorough knowledge on different Advanced Oxidation Process methods and to assess their mineralization efficacy of emerging contaminants. This study indicates the need for an integrated process for enhancing the treatment efficiency and overcoming the drawbacks of the individual Advanced Oxidation Process. Further, its application concerning technical and economic aspects is reviewed. Until now, most of the studies have been based on lab or pilot scale and do not represent the actual scenario of the emerging contaminant mineralization. Thus, the scaling up of the process was discussed, and the major challenges in large scale implementation were pointed out.

Graphene Oxide, Carbon Nanotubes, and Polyelectrolytes-Based Impedanciometric E-Tongue for Estrogen Detection in Complex Matrices

Currently, it is necessary to maintain the quality of aquifers and water bodies, which means the need for sensors that detect molecules as emerging pollutants (EPs) at low concentrations in aqueous complex solutions. In this work, an electronic tongue (e-tongue) prototype was developed to detect 17β-estradiol in tap water. To achieve such a prototype, an array of sensors was prepared. Each sensor consists of a solid support with interdigitated electrodes without or with thin films prepared with graphene oxide, nanotubes, and other polyelectrolytes molecules adsorbed on them. To collect data from each sensor, impedance spectroscopy was used to analyze the electrical characteristics of samples of estrogen solutions with different concentrations. To analyze the collected data from the sensors, principal components analysis (PCA) method was used to create a three-dimensional plane using the calculated principal components, namely PC1 and PC2, and the estrogen concentration values. Then, damped least squares (DLS) was used to find the optimal values for the hyperplane calibration, as the sensitivity of this e-tongue was not represented by a straight line but by a surface. For the collected data, from nanotubes and graphene oxide sensors, a calibration curve for concentration given by the 10PC1×0.492-PC2×0.14-14.5 surface was achieved. This e-tongue presented a detection limit of 10-16 M of 17β-estradiol in tap water.

Application of Ion Mobility Spectrometry and the Derived Collision Cross Section in the Analysis of Environmental Organic Micropollutants

Ion mobility spectrometry (IMS) is a rapid gas-phase separation technique, which can distinguish ions on the basis of their size, shape, and charge. The IMS-derived collision cross section (CCS) can serve as additional identification evidence for the screening of environmental organic micropollutants (OMPs). In this work, we summarize the published experimental CCS values of environmental OMPs, introduce the current CCS prediction tools, summarize the use of IMS and CCS in the analysis of environmental OMPs, and finally discussed the benefits of IMS and CCS in environmental analysis. An up-to-date CCS compendium for environmental contaminants was produced by combining CCS databases and data sets of particular types of environmental OMPs, including pesticides, drugs, mycotoxins, steroids, plastic additives, per- and polyfluoroalkyl substances (PFAS), polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs), and polybrominated diphenyl ethers (PBDEs), as well as their well-known transformation products. A total of 9407 experimental CCS values from 4170 OMPs were retrieved from 23 publications, which contain both drift tube CCS in nitrogen (DTCCSN2) and traveling wave CCS in nitrogen (TWCCSN2). A selection of publicly accessible and in-house CCS prediction tools were also investigated; the chemical space covered by the training set and the quality of CCS measurements seem to be vital factors affecting the CCS prediction accuracy. Then, the applications of IMS and the derived CCS in the screening of various OMPs were summarized, and the benefits of IMS and CCS, including increased peak capacity, the elimination of interfering ions, the separation of isomers, and the reduction of false positives and false negatives, were discussed in detail. With the improvement of the resolving power of IMS and enhancements of experimental CCS databases, the practicability of IMS in the analysis of environmental OMPs will continue to improve.

Recent Advances on Electrochemical Sensors for Detection of Contaminants of Emerging Concern (CECs)

Contaminants of Emerging Concern (CECs), a new category of contaminants currently in the limelight, are a major issue of global concern. The pervasive nature of CECs and their harmful effects, such as cancer, reproductive disorders, neurotoxicity, etc., make the situation alarming. The perilous nature of CECs lies in the fact that even very small concentrations of CECs can cause great impacts on living beings. They also have a nature of bioaccumulation. Thus, there is a great need to have efficient sensors for the detection of CECs to ensure a safe living environment. Electrochemical sensors are an efficient platform for CEC detection as they are highly selective, sensitive, stable, reproducible, and prompt, and can detect very low concentrations of the analyte. Major classes of CECs are pharmaceuticals, illicit drugs, personal care products, endocrine disruptors, newly registered pesticides, and disinfection by-products. This review focusses on CECs, including their sources and pathways, health effects caused by them, and electrochemical sensors as reported in the literature under each category for the detection of major CECs.

Sustainable application of electrocatalytic and photo-electrocatalytic oxidation systems for water and wastewater treatment: a review

Wastewater treatment and reuse have risen as a solution to the water crisis plaguing the world. Global warming-induced climate change, population explosion and fast depletion of groundwater resources are going to exacerbate the present global water problems for the forthcoming future. In this scenario, advanced electrochemical oxidation process (EAOP) utilising electrocatalytic (EC) and photoelectrocatalytic (PEC) technologies have caught hold of the interest of the scientific community. The interest stems from the global water management plans to scale down centralised water and wastewater treatment systems to decentralised and semicentralised treatment systems for better usage efficiency and less resource wastage. In an age of rising water pollution caused by contaminants of emerging concern (CECs), EC and PEC systems were found to be capable of optimal mineralisation of these pollutants rendering them environmentally benign. The present review treads into the conventional electrochemical treatment systems to identify their drawbacks and analyses the scope of the EC and PEC to mitigate them. Probable electrode materials, potential catalysts and optimal operational conditions for such applications were also examined. The review also discusses the possible retrospective application of EC and PEC as point-of-use and point-of-entry treatment systems during the transition from conventional centralised systems to decentralised and semi-centralised water and wastewater treatment systems.

Insights in Pharmaceutical Pollution: The Prospective Role of eDNA Metabarcoding

Environmental pollution is a growing threat to natural ecosystems and one of the world's most pressing concerns. The increasing worldwide use of pharmaceuticals has elevated their status as significant emerging contaminants. Pharmaceuticals enter aquatic environments through multiple pathways related to anthropogenic activity. Their high consumption, insufficient waste treatment, and the incapacity of organisms to completely metabolize them contribute to their accumulation in aquatic environments, posing a threat to all life forms. Various analytical methods have been used to quantify pharmaceuticals. Biotechnology advancements based on next-generation sequencing (NGS) techniques, like eDNA metabarcoding, have enabled the development of new methods for assessing and monitoring the ecotoxicological effects of pharmaceuticals. eDNA metabarcoding is a valuable biomonitoring tool for pharmaceutical pollution because it (a) provides an efficient method to assess and predict pollution status, (b) identifies pollution sources, (c) tracks changes in pharmaceutical pollution levels over time, (d) assesses the ecological impact of pharmaceutical pollution, (e) helps prioritize cleanup and mitigation efforts, and (f) offers insights into the diversity and composition of microbial and other bioindicator communities. This review highlights the issue of aquatic pharmaceutical pollution while emphasizing the importance of using modern NGS-based biomonitoring actions to assess its environmental effects more consistently and effectively.

Continuous removal of caffeine in a horizontal-flow anaerobic immobilized biomass bioreactor: identification of transformation products

Anaerobic bioreactors are an efficient technology for the biodegradation of emerging contaminants in environmental matrices. In this work, a horizontal-flow anaerobic immobilized biomass (HAIB) bioreactor was used to remove caffeine (CAF), which is frequently found in various aqueous matrices. The acrylic bench top bioreactor, with dimensions of 100 × 5.00 cm, was operated with a hydraulic retention time (HRT) of 12 h, during 45 weeks, under mesophilic conditions. The operation was performed in 4 phases: without CAF addition (phase I); CAF spiked at 300 μg L-1 (phase II); CAF at 600 μg L-1 (phase III); and CAF at 900 μg L-1 (phase IV). Samples of bioreactor influent and effluent were analyzed by liquid chromatography/tandem mass spectrometry (LC-MS/MS). The bioreactor removed organic matter (OM) and CAF with efficiencies of 88 and 93%, respectively. The first-order apparent removal constant (Kapp) values for OM and CAF were 0.419 and 0.304 h-1, respectively. Five transformation products (TPs) were identified, with m/z 243, 227, 211, and 181 (two products). The HAIB bioreactor is a suitable system for the removal of CAF present in wastewater, even at a concentration level of µg L-1.

Target Exposome for Characterizing Early Gestational Exposure to Contaminants of Emerging Concern and Association with Gestational Diabetes Mellitus

Characterization of gestational exposure to complex contaminants of emerging concern (CECs) is critical to the identification of environmental risk factors for pregnancy complications. However, determination of various CECs with diverse physicochemical properties in biological fluids is technically challenging. In the present study, we developed a target exposome protocol, consisting of simple liquid-liquid extraction-based sample preparation and sensitive liquid chromatography-tandem mass spectrometry (LC-MS/MS) analysis, to determine 325 CECs covering 11 subclasses, including poly- and perfluoroalkyl substances, organophosphate esters, ultraviolet (UV) stabilizers, synthetic antioxidants, phthalate esters, and several others. The protocol exhibits exceptional advantages over traditional approaches in the coverage of chemicals, sample volume demand, and time and financial cost. The protocol was applied in a prospective nested gestational diabetes mellitus (GDM) study including 120 cases and 240 matched healthy controls. Thirty-three CECs were detected in >70% of the samples, with a combined concentration of 17.0-484.7 ng/mL. Bayesian kernel machine regression analysis showed that exposure to the CEC mixture was significantly associated with a higher GDM risk. For example, when increasing all CECs in the mixture from 50th percentile to 75th percentile, the estimated probit of GDM incidence had an increase of 92% (95% CI: 56%, 127%). Meanwhile, perfluorohexanesulfonic acid, 1,3-diphenylguanidine, and dibutyl fumarate were identified as the key CECs driving the joint effect. This work demonstrates great potential of our target exposome protocol for environmental risk factor identification in large-scale epidemiology or biomonitoring studies.

International Comparison, Risk Assessment, and Prioritisation of 26 Endocrine Disrupting Compounds in Three European River Catchments in the UK, Ireland, and Spain

Endocrine-disrupting compounds (EDCs) constitute a wide variety of chemistries with diverse properties that may/can pose risks to both humans and the environment. Herein, a total of 26 compounds, including steroids, flame retardants, and plasticizers, were monitored in three major and heavily urbanized river catchments: the R. Liffey (Ireland), the R. Thames (UK), and the R. Ter (Spain), by using a single solid-phase extraction liquid chromatography-mass spectrometry (SPE-LC-MS/MS) method. Occurrence and frequency rates were investigated across all locations over a 10-week period, with the highest concentration obtained for the flame retardant tris(2-chloroethyl) phosphate (TCEP) at 4767 ng∙L-1 in the R. Thames in Central London. Geographical variations were observed between sites and were partially explained using principal component analysis (PCA) and hierarchical cluster analysis (HCA). In particular, discrimination between the R. Ter and the R. Thames was observed based on the presence and concentration of flame retardants, benzotriazole, and steroids. Environmental risk assessment (ERA) across sites showed that caffeine, a chemical marker, and bisphenol A (BPA), a plasticizer, were classified as high-risk for the R. Liffey and R. Thames, based on relative risk quotients (rRQs), and that caffeine was classified as high-risk for the R. Ter, based on RQs. The total risks at each location, namely ΣRQriver, and ΣrRQriver, were: 361, 455, and 723 for the rivers Liffey, Thames, and Ter, respectively. Caffeine, as expected, was ubiquitous in all 3 urban areas, though with the highest RQ observed in the R. Ter. High contributions of BPA were also observed across the three matrices. Therefore, these two compounds should be prioritized independently of location. This study represents a comprehensive EDC monitoring comparison between different European cities based on a single analytical method, which allowed for a geographically independent ERA prioritization to be performed.

An overview of biogenic metallic nanoparticles for water treatment and purification: the state of the art

The environment is fundamental to human existence, and protecting it from dangerous contaminants should be a top priority for all stakeholders. Reducing garbage output has helped, but as the world's population grows, more waste will be generated. Tons of waste inadvertently and advertently received by environmental matrixes adversely affect the sustainable environment. The pollution caused by these activities affects the environment and human health. Conventional remediation processes ranging from chemical, physical, and biological procedures use macroaggregated materials and microorganisms to degrade or remove pollutants. Undesirable limitations of expensiveness, disposal challenges, maintenance, and formation of secondary contaminants abound. Additionally, multiple stages of treatments to remove different contaminants are time-consuming. The need to avoid these limitations and shift towards sustainable approaches brought up nanotechnology options. Currently, nanomaterials are being used for environmental rejuvenation that involves the total degradation of pollutants without secondary pollution. As nanoparticles are primed with vast and modifiable reactive sites for adsorption, photocatalysis, and disinfection, they are more useful in remediating pollutants. Review articles on metallic nanoparticles usually focus on chemically synthesized ones, with a particular focus on their adsorption capacity and toxicities. Therefore, this review evaluates the current status of biogenic metallic nanoparticles for water treatment and purification.

Comparison of effects of multiple oxidants with an ultrasonic system under unified system conditions for bisphenol A degradation

Bisphenol A (BPA) as a trace contaminant has been reported, due to widespread use in the plastics industry. This study applied the 35 kHz ultrasound (US) to activate four different common oxidants (H₂O₂, HSO₅^-, S₂O₈^2-, and IO₄^-) for BPA degradation. With increasing initial concentration of oxidants, the degradation rate of BPA increased. The synergy index confirmed that a synergistic relationship between US and oxidants. This study also examined the impact of pH and temperature. The results showed that the kinetic constants of US, US-H₂O₂, US-HSO₅^- and US-IO₄^-decreased when the pH increased from 6 to 11. The optimal pH for US-S₂O₈^2- was 8. Notably, increasing temperature decreased the performance of US, US-H₂O₂, and US-IO₄^- systems, while it could increase the degradation of BPA in US-S₂O₈^2- and US-HSO₅^-. The activation energy for BPA decomposition using the US-IO₄^- system was the lowest, at 0.453nullkJnullmol^-1, and the synergy index was the highest at 2.22. Additionally, the ΔG# value was found to be 2.11 + 0.29T when the temperature ranged from 25 °C to 45 °C. The main oxidation contribution is achieved by hydroxyl radicals in scavenger test. The mechanism of activation of US-oxidant is heat and electron transfer. In the case of the US-IO₄^- system, the economic analysis yielded 271 kwh m^-3, which was approximately 2.4 times lower than that of the US process.

H2O2 activation and contaminants removal in heterogeneous Fenton-like systems

Emerging contaminants can be removed effectively in heterogeneous Fenton-like systems. Currently, catalyst activity and contaminant removal mechanisms have been studied extensively in Fenton-like systems. However, a systematic summary was lacking. This review summarized: 1) The effects of various heterogeneous catalysts on emerging contaminants degradation by activating H₂O₂; 2) The role of active sites in different catalysts during the activation of H₂O₂ and their contribution to the generation of active species; 3) The modulation of degradation pathways of emerging contaminants. This paper will help scholars to advance the controlled construction of active sites in heterogeneous Fenton-like systems. Suitable heterogeneous Fenton catalysts can be selected in practical water treatment processes.

Novel Sb-doped SnO2 ceramic anode coated with a photoactive BiPO4 layer for the photoelectrochemical degradation of an emerging pollutant

In the present work, a study about the electrochemical and photoelectrochemical degradation of an emerging pollutant using an Sb-doped SnO₂ anode coated with a photocatalytic layer of BiPO₄ has been performed. The electrochemical characterization of the material was carried out by means of linear sweep voltammetry, light-pulsed chronoamperometry and electrochemical impedance spectroscopy. These studies confirmed that the material is photoactive at intermediate potential values (around 2.5 V), and that the charge transfer resistance decreases in the presence of light. A positive effect of the illuminated area on the degradation degree of norfloxacin was observed: at 15.50 mA cm^-2, the degradation rate was 83.37% in the absence of light, 92.24% with an illuminated area of 5.7 cm², and it increased up to 98.82% with an illuminated area of 11.4 cm². The kinetics of the process were evaluated, and the by-products of the degradation were identified by ion chromatography and HPLC. In the case of the mineralization degree, the effect of light is less significant, especially at higher current densities. The specific energy consumption of the process was lower in the photoelectrochemical experiments as compared to the experiments in dark conditions. At intermediate current densities (15.50 mA cm^-2) a decrease in energy consumption of 53% was achieved by illuminating the electrode.

Exploring the Impact of Contaminants of Emerging Concern on Fish and Invertebrates Physiology in the Mediterranean Sea

In this historical context, the Mediterranean Sea faces an increasing threat from emerging pollutants such as pharmaceuticals, personal care products, heavy metals, pesticides and microplastics, which pose a serious risk to the environment and human health. In this regard, aquatic invertebrates and fish are particularly vulnerable to the toxic effects of these pollutants, and several species have been identified as bio-indicators for their detection. Among these, bivalve molluscs and elasmobranchs are now widely used as bio-indicators to accurately assess the effects of contaminants. The study focuses on the catshark Scyliorhinus canicular and on the Mediterranean mussel Mytilus galloprovincialis. The first one is a useful indicator of localised contamination levels due to its exposure to pollutants that accumulate on the seabed. Moreover, it has a high trophic position and plays an important role in the Mediterranean Sea ecosystem. The bivalve mollusc Mytilus galloprovincialis, on the other hand, being a filter-feeding organism, can acquire and bioaccumulate foreign particles present in its environment. Additionally, because it is also a species of commercial interest, it has a direct impact on human health. In conclusion, the increasing presence of emerging pollutants in the Mediterranean Sea is a serious issue that requires immediate attention. Bivalve molluscs and elasmobranchs are two examples of bio-indicators that must be used to precisely determine the effects of these pollutants on the marine ecosystem and human health.

Calibration of a microporous polyethylene tube passive sampler for polar organic compounds in wastewater effluent

Water resources are vulnerable to contamination from polar organic compounds (POCs) originating from sources such as wastewater effluent. Two configurations of a microporous polyethylene tube (MPT) passive sampler were investigated for the time-integrative detection and quantification of POCs in effluent. One configuration contained the polymeric reversed phase sorbent Strata-X (SX) and the other Strata-X suspended in agarose gel (SX-Gel). These were deployed for up to 29 days and analysed for forty-nine POCs including pesticides, pharmaceuticals and personal care products (PPCPs) together with illicit drugs. Complementary composite samples were collected on days 6, 12, 20 and 26 representing the previous 24 h. Thirty-eight contaminants were detected in composite samples and MPT extracts, with MPT sampling rates (R_s) for 11 pesticides and 9 PPCPs/drugs ranging from 0.81 to 10.32 mL d^-1 in SX and 1.35-32.83 mL d^-1 in SX-Gel. Half-times to equilibrium of contaminants with the SX and SX-Gel equipped samplers ranged from two days to >29 days. MPT (SX) samplers were also deployed at 10 wastewater treatment effluent discharge sites across Australia for 7 days (again with complementary composite samples), to validate the sampler performance under varying conditions. Extracts from these MPTs detected 48 contaminants in comparison with 46 in composite samples, with concentrations ranging from 0.1 to 138 ng mL^-1. An advantage of the MPT was preconcentration of contaminants, resulting in extract levels often markedly above instrument analytical detection limits. The validation study demonstrated a high correlation between accumulated contaminant mass in the MPTs and wastewater concentrations from composite samples (r² > 0.70, where concentrations in composite samples were > 3× LOD). The MPT sampler shows promise as a sensitive tool for detecting POCs at trace levels in wastewater effluent and also quantifying these levels if temporal concentration variations are not significant.

An overview on ZnO-based sonophotocatalytic mitigation of aqueous phase pollutants

Over the past several decades, the increase in industrialization provoked the discharge of harmful pollutants into the environment, affecting human beings and ecosystems. ZnO-based photocatalysts seem to be the most promising photocatalysts for treating harmful pollutants. However, fast charge carrier recombination, photo corrosion, and long reaction time are the significant factors that reduce the photoactivity of ZnO-based photocatalysts. In order to enhance the photoactivity of such photocatalysts, a combined process i.e., sonocatalysis + photocatalysis = sonophotocatalysis was used. Sonophotocatalysis is one of several different AOP methods that have recently drawn considerable interest, as it produces high reactive oxygen species (ROS) which helps in the oxidation of pollutants by acoustic cavitation. This combined technique enhanced the overall efficiency of the individual method by overcoming its limiting factors. The current review aims to present the theoretical and fundamental aspects of sonocatalysis and photocatalysis along with a detailed discussion on the benefits that can be obtained by the combined process i.e., US + UV (sonophotocatalysis). Also, we have provided a comparison of the excellent performance of ZnO to that of the other metal oxides. The purpose of this study is to discuss the literature concerning the potential applications of ZnO-based sonophotocatalysts for the degradation of pollutants i.e., dyes, antibiotics, pesticides, phenols, etc. That are carried out for future developments. The role of the produced ROS under light and ultrasound stimulation and the degradation mechanisms that are based on published literature are also discussed. In the end, future perspectives are suggested, that are helpful in the development of the sonophotocatalysis process for the remediation of wastewater containing various pollutants.

The Minus Approach Can Redefine the Standard of Practice of Drinking Water Treatment

Chlorine-based disinfection for drinking water treatment (DWT) was one of the 20th century's great public health achievements, as it substantially reduced the risk of acute microbial waterborne disease. However, today's chlorinated drinking water is not unambiguously safe; trace levels of regulated and unregulated disinfection byproducts (DBPs), and other known, unknown, and emerging contaminants (KUECs), present chronic risks that make them essential removal targets. Because conventional chemical-based DWT processes do little to remove DBPs or KUECs, alternative approaches are needed to minimize risks by removing DBP precursors and KUECs that are ubiquitous in water supplies. We present the "Minus Approach" as a toolbox of practices and technologies to mitigate KUECs and DBPs without compromising microbiological safety. The Minus Approach reduces problem-causing chemical addition treatment (i.e., the conventional "Plus Approach") by producing biologically stable water containing pathogens at levels having negligible human health risk and substantially lower concentrations of KUECs and DBPs. Aside from ozonation, the Minus Approach avoids primary chemical-based coagulants, disinfectants, and advanced oxidation processes. The Minus Approach focuses on bank filtration, biofiltration, adsorption, and membranes to biologically and physically remove DBP precursors, KUECs, and pathogens; consequently, water purveyors can use ultraviolet light at key locations in conjunction with smaller dosages of secondary chemical disinfectants to minimize microbial regrowth in distribution systems. We describe how the Minus Approach contrasts with the conventional Plus Approach, integrates with artificial intelligence, and can ultimately improve the sustainability performance of water treatment. Finally, we consider barriers to adoption of the Minus Approach.

Contaminants of Emerging Concern (CECs) and Male Reproductive Health: Challenging the Future with a Double-Edged Sword

Approximately 9% of couples are infertile, with half of these cases relating to male factors. While many cases of male infertility are associated with genetic and lifestyle factors, approximately 30% of cases are still idiopathic. Contaminants of emerging concern (CECs) denote substances identified in the environment for the first time or detected at low concentrations during water quality analysis. Since CEC production and use have increased in recent decades, CECs are now ubiquitous in surface and groundwater. CECs are increasingly observed in human tissues, and parallel reports indicate that semen quality is continuously declining, supporting the notion that CECs may play a role in infertility. This narrative review focuses on several CECs (including pesticides and pharmaceuticals) detected in the nearshore marine environment of False Bay, Cape Town, South Africa, and deliberates their potential effects on male fertility and the offspring of exposed parents, as well as the use of spermatozoa in toxicological studies. Collective findings report that chronic in vivo exposure to pesticides, including atrazine, simazine, and chlorpyrifos, is likely to be detrimental to the reproduction of many organisms, as well as to sperm performance in vitro. Similarly, exposure to pharmaceuticals such as diclofenac and naproxen impairs sperm motility both in vivo and in vitro. These contaminants are also likely to play a key role in health and disease in offspring sired by parents exposed to CECs. On the other side of the double-edged sword, we propose that due to its sensitivity to environmental conditions, spermatozoa could be used as a bioindicator in eco- and repro-toxicology studies.

Elucidating the Effects of the Lipids Regulators Fibrates and Statins on the Health Status of Finfish Species: A Review

The most documented fibrates are gemfibrozil, clofibrate and bezafibrate, while for statins, the majority of the published literature focuses on atorvastatin and simvastatin. The present work reviews previously published research concerning the effects of these hypocholesterolaemic pharmaceuticals on fish, with a particular focus on commercially important species, commonly produced by the European aquaculture industry, specifically in recirculated aquaculture systems (RAS). Overall, results suggest that both acute and chronic exposures to lipid-lowering compounds may have adverse effects on fish, disrupting their capacity to excrete exogenous substances, as well as both lipid metabolism and homeostasis, causing severe ontogenetic and endocrinological abnormalities, leading to hampered reproductive success (e.g., gametogenesis, fecundity), and skeletal or muscular malformations, having serious repercussions on fish health and welfare. Nonetheless, the available literature focusing on the effects of statins or fibrates on commonly farmed fish is still limited, and further research is required to understand the implications of this matter on aquaculture production, global food security and, ultimately, human health.

In-situ Electrochemical Synthesis of H2O2 for p-nitrophenol Degradation Utilizing a Flow-through Three-dimensional Activated Carbon Cathode with Regeneration Capabilities

The growing ubiquity of recalcitrant organic contaminants in the aqueous environment poses risks to effective and efficient water treatment and reuse. A novel three-dimensional (3D) electrochemical flow-through reactor employing activated carbon (AC) encased in a stainless-steel (SS) mesh as a cathode is proposed for the removal and degradation of a model recalcitrant contaminant p-nitrophenol (PNP), a toxic compound that is not easily biodegradable or naturally photolyzed, can accumulate and lead to adverse environmental health outcomes, and is one of the more frequently detected pollutants in the environment. As a stable 3D electrode, granular AC supported by a SS mesh frame as a cathode is hypothesized to 1) electrogenerate H2O2 via a 2-electron oxygen reduction reaction on the AC surface, 2) initiate decomposition of this electrogenerated H2O2 to form hydroxyl radicals on catalytic sites of the AC surface 3) remove PNP molecules from the waste stream via adsorption, and 4) co-locate the PNP contaminant on the carbon surface to allow for oxidation by formed hydroxyl radicals. Additionally, this design is utilized to electrochemically regenerate the AC within the cathode that is significantly saturated with PNP to allow for environmentally friendly and economic reuse of this material. Under flow conditions with optimized parameters, the 3D AC electrode is nearly 20% more effective than traditional adsorption in removing PNP. 30 grams of AC within the 3D electrode can remove 100% of the PNP compound and 92% of TOC under flow. The carbon within the 3D cathode can be electrochemically regenerated in the proposed flow system and design thereby increasing the adsorptive capacity by 60%. Moreover, in combination with continuous electrochemical treatment, the total PNP removal is enhanced by 115% over adsorption. It is anticipated this platform holds great promises to eliminate analogous contaminants as well as mixtures.

Degradation of contaminants of emerging concern in a secondary effluent using synthesized MOF-derived photoanodes: A comparative study between photo-, electro- and photoelectrocatalysis

Three metal-organic framework (MOF)-based photoanodes were prepared by deposition on TiO₂ nanotubes using Ti as substrate (Ti/TiO₂NT): i) Ti/TiO₂NT-Au@ZIF-8, ii) Ti/TiO₂NT-Ru₃(BTC)₂, iii) Ti/TiO₂NT-UiO-66(Zr)NH₂. These photoanodes were characterized by FEG-SEM, EDX and DRX. The analyses showed a successful modification and a high homogeneity of the different MOFs on the Ti/TiO₂NT surface. The photoanodes were studied in the degradation of Contaminants of Emerging Concern (CECs) in a spiked secondary effluent from a Municipal Wastewater Treatment Plant (MWWTP). Sodium diclofenac (DCF), sulfamethazine (SMT) and carbamazepine (CBZ) were used as CECs at low concentration (200 μg/L each CEC). The samples were preconcentrated using Solid Phase Extraction (SPE) and analyzed by a HPLC-DAD system. The MOF-based photoanodes exhibited a high photoelectrochemical (PEC) activity towards the oxidation of CECs, achieving up to 50%, 70% and 80% of removal using Ti/TiO₂NT-Au@ZIF-8, Ti/TiO₂NT-UiO-66(Zr)NH₂, Ti/TiO₂NT-Ru₃(BTC), respectively. The influence of the generation of hydroxyl radical was then studied. The results indicate that PEC degradation using Ti/TiO₂NT-Ru₃(BTC)₂ and Ti/TiO₂NT-UiO-66(Zr)NH₂ is more affected by the concentration of the radical.

A critical review over the removal of paracetamol (acetaminophen) from synthetic waters and real wastewaters by direct, hybrid catalytic, and sequential ozonation processes

Paracetamol (PCT) or acetaminophen is a widely prescribed drug to treat fever and mild to moderate pain. The PCT uptake by animals and humans is not complete, being excreted through their urine to contaminate the aquatic/natural environments. Trace amounts of this drug have been found in sewage sludge, hospital wastewaters, wastewater plant treatments, surface waters, and even drinking water. PCT denatures proteins and oxidize lipids in cells with damage of their genetic code. Its toxicity over macrophytes, protozoan, algae, bacteria, and fishes has been reported. Ozonation methods have been proposed as efficient treatments to solve this pollution. This comprehensive and critical review is focused on the application of ozonation processes to remove PCT polluted water from different sources, like natural waters, synthetic waters, and real wastewaters. The fundamentals, operating variables, and best results by direct ozonation and hybrid catalytic ozonation are described, with attention to produced reactive oxygen species and their oxidative action. Single ozonation, catalytic modification of materials, and hybrid non-catalytic processes are detailed as direct ozonation methods. Ozonation with metal-based catalysts and photolytic and photocatalytic ozonation as hybrid catalytic methods are analyzed. Sequential non-biological and biological treatments with ozone and ozonation for wastewater remediation in treatment plants are described. Reaction sequences proposed for PCT mineralization are finally discussed, showing the initial formation of hydroquinone and 2-hydroxy-4-(N-acetyl)-aminophenol and their consecutive evolution to ultimate carboxylic acids like oxalic and oxamic. The ability of the methods to destroy these acids and their iron- and/or copper-complexes explains their mineralization performance.

Photocatalytic Degradation of Inherent Pharmaceutical Concentration Levels in Real Hospital WWTP Effluents Using g-C3N4 Catalyst on CPC Pilot Scale Reactor

The objective of this work was to evaluate the efficiency of a solar photocatalytic process using g-C₃N₄ as photocatalyst on the degradation of pharmaceutical compounds detected in hospital wastewater treatment plant secondary effluents. A compound parabolic collector pilot plant, established in the secondary effluent stream of the Ioannina city hospital wastewater treatment plant, was used for the photocatalytic experiments. The analysis of the samples before and after the photocatalytic treatment was accomplished using solid phase extraction (SPE), followed by UHPLC-LTQ/Orbitrap HRMS. Initial effluent characterization revealed the presence of ten pharmaceutical compounds. Among these, amisulpride, O-desmethyl venlafaxine, venlafaxine and carbamazepine were detected in all experiments. Initial concentrations ranged from 73 ng L^-1 for citalopram to 2924.53 ng L^-1 for O-desmethyl venlafaxine. The evolution of BOD₅ and COD values were determined before and after the photocatalytic treatment. All detected pharmaceuticals were removed in percentages higher than 54% at an optimum catalyst loading ranging between 200 and 300 mg L^-1. The potential of the catalyst to be reused without any treatment for two consecutive cycles was studied, showing a significant efficiency decrease.

Chemicals/materials of emerging concern in farmlands: sources, crop uptake and potential human health risks

Certain chemicals/materials that are contaminants of emerging concern (CECs) have been widely detected in water bodies and terrestrial systems worldwide while other CECs occur at undetectable concentrations. The primary sources of CECs in farmlands are agricultural inputs, such as wastewater, biosolids, sewage sludge, and agricultural mulching films. The percent increase in cropland area during 1950-2016 was 30 and the rise in land use for food crops during 1960-2018 was 100-500%, implying that there could be a significant CEC burden in farmlands in the future. In fact, the alarming concentrations (μg kg^-1) of certain CECs such as PBDEs, PAEs, and PFOS that occur in farmlands are 383, 35 400 and 483, respectively. Also, metal nanoparticles are reported even at the mg kg^-1 level. Chronic root accumulation followed by translocation of CECs into plants results in their detectable concentrations in the final plant produce. Thus, there is a continuous flow of CECs from farmlands to agricultural produce, causing a serious threat to the terrestrial food chain. Consequently, CECs find their way to the human body directly through CEC-laden plant produce or indirectly via the meat of grazing animals. Thus, human health could be at the most critical risk since several CECs have been shown to cause cancers, disruption of endocrine and cognitive systems, maternal-foetal transfer, neurotoxicity, and genotoxicity. Overall, this comprehensive review provides updated information on contamination of chemicals/materials of concern in farmlands globally, sources for their entry, uptake by crop plants, and their likely impact on the terrestrial food chain and human health.

Structural features promoting adsorption of contaminants of emerging concern onto TiO2 P25: experimental and computational approaches

The study of the structural features affecting the adsorption of organics, especially contaminants of emerging concern (CECs), onto TiO₂ P25 in aqueous medium has far-reaching implications for the understanding and modification of TiO₂ P25 in the roles such as an adsorbent and photocatalyst. The effect of pH and γ(TiO₂ P25) as variables on the extent of removal of organics by adsorption on TiO₂ P25 was investigated by response surface methodology (RSM) and quantitative structure-property relationship (QSPR) modeling. Experimentally determined coefficients of adsorption were used as responses in RSM, yielding a quadratic polynomial equation (QPE) for each of the studied organics. Furthermore, coefficients (A, B, C, D, E, and F) obtained from QPEs were used as responses in QSPR modeling to establish their dependence on the structural features of the studied organics. The functional stability and predictive power of the resulting QSPR models were confirmed with internal and external cross validation. The influence of structural features of organics on the adsorption process is explained by molecular descriptors included in the derived QSPR models. The most influential descriptors on the adsorption of organics on TiO₂ P25 are found to be those correlated with ionization potential, molecular mass, and volume, then molecular fragments (e.g., -CH =) and particular topological features such as C and N atoms, or two heteroatoms (e.g., N and N or O and Cl) at certain distance. Derived QSPR models can be considered as robust predictive tools for evaluating efficiency of adsorption processes onto TiO₂ P25, providing insights into influential structural features facilitating adsorption process.

Integrated full-scale solar CPC/UV-LED–filtration system as a tertiary treatment in a conventional WWTP for agricultural reuse purposes

Today, the emergence of increasingly restrictive treatment and reuse policies make the implementation of full-scale tertiary treatment, capable of improving the quality of water, a priority. Full-scale TiO2 photocatalysis systems are resulting in a promising option, since TiO2 is commercially available. However, questions such as how to work continuously during day/night irradiation cycle, or the removing of TiO2 in outlet flow are still unresolved. In this work, a full-scale system integrating a solar CPC/UV-LED step combined with commercial microfiltration membranes was installed in a conventional WWTP for agricultural reuse purposes. After optimization, 0.5 g/L of catalyst and combined SOLAR + UV-LED showing the highest pharmaceutical removal percentages, while a self-designed UV-LED included in the own reaction tank resulting in higher efficiencies compared with commercial lamps. Longer membrane surface area decreased fouling problems in the system. However, 60 min of irradiation time was necessary to reach the most restrictive water quality values according with (EU 2020/741). After optimization step, total costs were reduced by 45%. However, it was shown that a reduction in operating and maintenance costs, along with the development of more effective and economical commercial filtration membranes is a key factor; therefore, working on these aspects is essential in the treated water cost reduction.

Graphical abstract

Mechanisms and application of microalgae on removing emerging contaminants from wastewater: A review

This study reviews the development of the ability of microalgae to remove emerging contaminants (ECs) from wastewater. Contaminant removal by microalgae-based systems (MBSs) includes biosorption, bioaccumulation, biodegradation, photolysis, hydrolysis, and volatilization. Usually, the existence of ECs can inhibit microalgae growth and reduce their removal ability. Therefore, three methods (acclimation, co-metabolism, and algal-bacterial consortia) are proposed in this paper to improve the removal performance of ECs by microalgae. Finally, due to the high removal performance of contaminants from wastewater by algal-bacterial consortia systems, three kinds of algal-bacterial consortia applications (algal-bacterial activatedsludge, algal-bacterial biofilm reactor, and algal-bacterial constructed wetland system) are recommended in this paper. These applications are promising for ECs removal. But most of them are still in their infancy, and limited research has been conducted on operational mechanisms and removal processes. Extra research is needed to clarify the applicability and cost-effectiveness of hybrid processes.

Surface-Enhanced Raman Spectroscopy Chips Based on Silver Coated Gold Nanostars

Surface-enhanced Raman scattering (SERS) is becoming widely used as an analytical tool, and the search for stable and highly responsive SERS substrates able to give ultralow detection of pollutants is a current challenge. In this paper we boosted the SERS response of Gold nanostars (GNS) demonstrating that their coating with a layer of silver having a proper thickness produces a 7-fold increase in SERS signals. Glass supported monolayers of these GNS@Ag were then prepared using simple alcoxyliane chemistry, yielding efficient and reproducible SERS chips, which were tested for the detection of molecules representative of different classes of pollutants. Among them, norfloxacin was detected down to 3 ppb, which is one of the lowest limits of detection obtained with this technique for the analyte.

A critical review on paracetamol removal from different aqueous matrices by Fenton and Fenton-based processes, and their combined methods

Paracetamol (PCT), also known as acetaminophen, is a drug used to treat fever and mild to moderate pain. After consumption by animals and humans, it is excreted through the urine to the sewer systems, wastewater treatment plants, and other aquatic/natural environments. It has been detected in trace amounts in effluents of wastewater plant treatments, sewage sludge, hospital wastewaters, surface waters, and drinking water. PCT can cause genetic code damage, oxidative degradation of lipids, and denaturation of protein in cells, and its toxicity has been well-proven in bacteria, algae, macrophytes, protozoan, and fishes. To avoid its harmful health problems over living beings, powerful Fenton and Fenton-based treatments as pre-eminent advanced oxidation processes (AOPs) have been developed because of the inefficient treatment by conventional treatments. This paper presents a comprehensive and critical review over the application of such Fenton technologies to remove PCT from natural waters, synthetic wastewaters, and real wastewaters. The characteristics and main results obtained using Fenton, photo-Fenton, electro-Fenton, and photoelectro-Fenton are described, making special emphasis in the oxidative action of the generated reactive oxygen species. Hybrid processes based on the coupling with ultrasounds, gamma radiation, photocatalysis, photoelectrocatalysis, zero-valent iron-activated persulfate, adsorption, and microbial fuel cells, are analyzed. Sequential treatments involving the initiation with plasma gliding arc discharge and post-biological process are detailed. Comparative results with other available AOPs are also described and discussed. Finally, 13 aromatic by-products and 9 short-linear aliphatic carboxylic acid detected during the PCT removal by Fenton and Fenton-based processes are reported, with the proposal of three parallel pathways for its initial degradation.