Simultaneous adsorption of tetracycline, amoxicillin, and ciprofloxacin by pistachio shell powder coated with zinc oxide nanoparticles

Effectiveness of fullerene/magnesium oxide nanocomposite in removing ciprofloxacin and tetracycline from aqueous solutions

The excessive use of antibiotics, including ciprofloxacin (CIP) and tetracycline (TC), poses negative impacts on both human health and ecosystems. In this work, fullerene/magnesium oxide (F/MgO) nanocomposite was prepared and studied as adsorbent for CIP and TC removal. Adding metal oxide to F led to a change in its characteristics which was confirmed by XRD, FTIR, SEM, and TEM. A maximal removal for 50 mg L-1 CIP was 84.6% at 60 min, pH 7, and 0.2 g L-1 of adsorbent dose. 43.6% of 50 mg L-1 of TC adsorbed at 60 min, pH 5, and 1 g L-1 of adsorbent dose. Adsorption thermodynamics elucidated that the adsorption on F/MgO nanocomposite were spontaneous and exothermic, and non-spontaneous and endothermic for CIP and TC, respectively. Pseudo-second-order kinetic model fitted well the adsorption data of CIP and TC. Various coexisting ions had different impacts on the adsorption efficiency of CIP and TC. The competitive adsorption between CIP and TC on the surface of F/MgO nanocomposite was studied. The F/MgO nanocomposite was efficiently reused 5 cycles for CIP and TC removal and remained effective. This work explores a novel adsorbent for the elimination of CIP and TC from aqueous solutions.

Adsorptive Effect of Corn Silk-Loaded Nickel Oxide and Copper Oxide Nanoparticles for Elimination of Ciprofloxacin from Wastewater

Ciprofloxacin (CIP) is one of the most reported antibiotic pollutants in hospital and industrial wastewater systems. The inclusion of nanosized transition metal oxides in adsorbent materials is able to improve the affinity and aqueous phase uptake of CIP from water. In this study, we report for the first time composites of corn silk with impregnated nanoparticles of NiO (NiONPs-CS) and CuO (CuONPs-CS) for the removal of CIP from water. The adsorbent was characterized using scanning electron microscopy (SEM), Fourier transform infrared (FTIR), energy-dispersive X-ray spectroscopy (EDX), an adsorption/desorption analyzer, and X-ray diffractometer (XRD) to study the morphology, surface functionality, elemental composition, textural properties, and crystal phases. The monolayer adsorption capacities of NiONPs-CS and CuONPs-CS were 108.3 and 120.2 mg/g, which were over 2 times higher than the capacity for unloaded corn silk. The kinetics of the adsorptive uptake followed the pseudo-second-order kinetics, revealing that both adsorption site density and CIP aqueous concentration control the removal rate. NiONPs-CS and CuONPs-CS were reusable for five cycles, with the uptake efficiency being 63.1 and 66.9%, respectively. This dropped to 47.8% for the unloaded corn silk. The mechanism of uptake was mainly by electrostatic attraction, pi-pi interaction, hydrogen bonding, and hydrophobic interaction. Based on our findings, the adsorbents have proven to be an efficient, cheap, and reusable material for CIP uptake.

Phyto-fabricated ZnO nanoparticles for anticancer, photo-antimicrobial effect on carbapenem-resistant/sensitive Pseudomonas aeruginosa and removal of tetracycline

Alternanthera sessilis (AS) leaf extract was used to synthesize zinc oxide nanoparticles (ZnO NPs). Bioanalytical characterization techniques such as X-ray diffraction (XRD) and field emission scanning electron microscope (FESEM) confirmed the formation of crystalline ZnO NPs with average sizes of 40 nm. The AS-ZnO NPs antimicrobial activity was analyzed under dark (D) and white light (WL) conditions. The improved antimicrobial activity was observed against Escherichia coli, Staphylococcus aureus and Bacillus subtilis at the minimal inhibitory concentration (MIC) of 125 and 62.5 µg/mL under WL than the D at 125 and 250 µg/mL for E. coli, B. subtilis, and Pseudomonas aeruginosa, respectively. In contrast, the growth of P. aeruginosa and S. aureus was not completely inhibited until 1 mg/mL AS-ZnO NPs under WL and D. Similarly, AS-ZnO NPs displayed a weaker inhibitory effect against carbapenem-sensitive P. aeruginosa (CSPA) and carbapenem-resistant P. aeruginosa (CRPA) strains of PAC023, PAC041 and PAC032, PAC045 under D. Interestingly, the distinct inhibitory effect was recorded against CSPA PAC041 and CRPA PAC032 in which the bacteria growth was inhibited 99.9% at 250, 500 µg/mL under WL. The cytotoxicity results suggested AS-ZnO NPs demonstrated higher toxicity to MCF-7 breast cancer cells than the RAW264.7 macrophage cells. Further, AS-ZnO NPs exhibited higher catalytic potential against tetracycline hydrochloride (TC-H) degradation at 65.6% and 60.8% under WL than the dark at 59.35% and 48.6% within 120 min. Therefore, AS-ZnO NPs can be used to design a photo-improved antimicrobial formulation and environmental catalyst for removing TC-H from wastewater.

A novel and sustainable composite of L@PSAC for superior removal of pharmaceuticals from different water matrices: Production, characterization, and application

This study endeavors to develop cost-effective environmentally friendly technology for removing harmful residual pharmaceuticals from water and wastewater by utilizing the effective adsorption of pistachio shell (PS) biochar and the degradation potency of laccase immobilized on the biochar (L@PSAC). The carbonatization and activation of the shells were optimized regarding temperature, time, and NH4NO3/PS ratio. This step yielded an optimum PS biochar (PSAC) with the highest porosity and surface area treated at 700 °C for 3 h using an NH4NO3/PS ratio of 3% wt. The immobilization of laccase onto PSAC (L@PSAC) was at its best level at pH 5, 60 U/g, and 30 °C. The optimum L@PSAC maintained a high level of enzyme activity over two months. Almost a complete removal (>99%) of diclofenac, carbamazepine, and ciprofloxacin in Milli-Q (MQ) water and wastewater was achieved. Adsorption was responsible for >80% of the removal and the rest was facilitated by laccase degradation. L@PSAC maintained effective removal of pharmaceuticals of ≥60% for up to six treatment cycles underscoring the promising application of this material for wastewater treatment. These results indicate that activated carbon derived from the pistachio shell could potentially be utilized as a carrier and adsorbent to efficiently remove pharmaceutical compounds. This enzymatic physical elimination approach has the potential to be used on a large-scale.

Properties and Possibilities of Using Biochar Composites Made on the Basis of Biomass and Waste Residues Ferryferrohydrosol Sorbent

Biochar enriched with metals has an increased potential for sorption of organic and inorganic pollutants. The aim of the research was to identify the possibility of using biochar composites produced on the basis of waste plant biomass and waste FFH (ferryferrohydrosol) containing iron atoms, after CO2 capture. The composites were produced in a one-stage or two-stage pyrolysis process. Their selected properties were determined as follows: pH, ash content, C, H, N, O, specific surface area, microstructure and the presence of surface functional groups. The produced biochar and composites had different properties resulting from the production method and the additive used. The results of experiments on the removal of methylene blue (MB) from solutions allowed us to rank the adsorbents used according to the maximum dye removal value achieved as follows: BC1 (94.99%), B (84.61%), BC2 (84.09%), BC3 (83.23%) and BC4 (83.23%). In terms of maximum amoxicillin removal efficiency, the ranking is as follows: BC1 (55.49%), BC3 (23.51%), BC2 (18.13%), B (13.50%) and BC4 (5.98%). The maximum efficiency of diclofenac removal was demonstrated by adsorbents BC1 (98.71), BC3 (87.08%), BC4 (74.20%), B (36.70%) and BC2 (30.40%). The most effective removal of metals Zn, Pb and Cd from the solution was demonstrated by BC1 and BC3 composites. The final concentration of the tested metals after sorption using these composites was less than 1% of the initial concentration. The highest increase in biomass on prepared substrates was recorded for the BC5 composite. It was higher by 90% and 54% (for doses of 30 g and 15 g, respectively) in relation to the biomass growth in the soil without additives. The BC1 composite can be used in pollutant sorption processes. However, BC5 has great potential as a soil additive in crop yield and plant growth.

Bioinspired Stevia rebaudiana Green Zinc Oxide Nanoparticles for the Adsorptive Removal of Antibiotics from Water

Green zinc oxide nanoparticles (ZnO NPs) synthesized using Stevia rebaudiana as a reducing agent were investigated as ecofriendly adsorbents for the removal of the antibiotics ciprofloxacin (CIP) and tetracycline (TET) from water. Green ZnO NPs were synthesized using a rapid novel approach that did not require annealing or calcination at high temperatures to produce mesoporous NPs with a size range of 37.36-71.33 nm, a specific surface area of 15.28 m2/g, and a negative surface charge of -15 mV at pH 5. The green ZnO NPs exhibited an antioxidant activity of 85.57% at 250 μg/mL and an antibacterial activity with MIC and MBC of 50 and 100 mg/mL, respectively, against both Escherichia coli and Staphylococcus aureus. The best adsorption performance was achieved using a 4 g/L dose and pH 5, yielding, respectively, 86.77 ± 0.82% removal and 27.07 ± 0.26 mg/g adsorption capacity for CIP at 10 mg/L and 67.86 ± 3.41% and 15.88 ± 0.37 mg/g for TET at 25 mg/L. The green ZnO NPs achieved 79.71% ± 0.28 and 61.55% ± 0.53 removal of 10 mg/L CIP and 25 mg/L TET, respectively, in a spiked tap water binary system of the two contaminants. Adsorption of CIP and TET occurred mainly via electrostatic interactions, whereby CIP was bound more strongly than TET by virtue of its charge and size. The synthesis and adsorption processes were evaluated by a stepwise regression statistical model to optimize their parameters. Lastly, the green ZnO NPs were regenerated and reused for 5 cycles, indicating their functionality as simple, reusable, and low-cost adsorbents for the removal of CIP and TET from wastewater, in accordance with SDGs #6 and 12 for the sustainable management of water.

Ciprofloxacin antibiotic removal from aqueous solutions by ZnO nanoparticles coated on ACA: modeling and optimization

Antibiotics are one of the most widely used drug groups. The presence of antibiotics in urban water sources and sewage creates many environmental and medical risks for humans and other living organisms. In this study, the potential of zinc oxide (ZnO) coated on almond shell activated carbon (ACA-ZnO) in removing ciprofloxacin (CIP) from aqueous solutions was investigated. Almond shell was used to make activated carbon. Zinc oxide nanoparticles were prepared by the sol-gel method, and finally, ZnO nanoparticles were bonded to activated carbon. The effect of independent parameters pH, contact time, adsorbent dose, and initial CIP concentration on CIP removal efficiency using ACA-ZnO was investigated by response surface methodology. Optimal removal was obtained at pH = 5.4, CIP initial concentration = 7.4 mg/L, adsorbent dose = 0.82 g/L, and reaction time = 67.3 min. This study followed a quadratic model (R2 = 0.958). The best model of adsorption isotherm fits with the Freundlich model (R2 = 0.9972) and the maximum capacity was 251.42 mg/g adsorption kinetics, and pseudo-second-order kinetic model (R2 = 0.959). The results of this study showed that ACA-ZnO as an adsorbent is very efficient, without environmental side effect and cost-benefit.

In Situ Synthesis of Doped Bio-Graphenes as Effective Metal-Free Catalysts in Removal of Antibiotics: Effect of Natural Precursor on Doping, Morphology, and Catalytic Activity

Wastewater contaminated with antibiotics is a major environmental challenge. The oxidation process is one of the most common and effective ways to remove these pollutants. The use of metal-free, green, and inexpensive catalysts can be a good alternative to metal-containing photocatalysts in environmental applications. We developed here the green synthesis of bio-graphenes by using natural precursors (Xanthan, Chitosan, Boswellia, Tragacanth). The use of these precursors can act as templates to create 3D doped graphene structures with special morphology. Also, this method is a simple method for in situ synthesis of doped graphenes. The elements present in the natural biopolymers (N) and other elements in the natural composition (P, S) are easily placed in the graphene structure and improve the catalytic activity due to the structural defects, surface charges, increased electron transfers, and high absorption. The results have shown that the hollow cubic Chitosan-derived graphene has shown the best performance due to the doping of N, S, and P. The Boswellia-derived graphene shows the highest surface area but a lower catalytic performance, which indicates the more effective role of doping in the catalytic activity. In this mechanism, O2 dissolved in water absorbs onto the positively charged C adjacent to N dopants to create oxygenated radicals, which enables the degradation of antibiotic molecules. Light irradiation increases the amount of radicals and rate of antibiotic removal.

Static adsorption and photocatalytic degradation of amoxicillin using titanium dioxide/hydroxyapatite nanoparticles based on sea scallop shells

The objective of this study is to investigate the efficiency of two processes for the amoxicillin removal through static (batch) adsorption and photocatalytic degradation onto the prepared samples. Three solid materials as photocatalyst and/or adsorbent were synthesized viz. nanotitanium dioxide (NT) prepared by the sol-gel method, scallop shells-based nanohydroxyapatite (NP), and nanotitanium dioxide/nanohydroxyapatite composite (NTP). The physicochemical and morphological properties of the prepared samples were tested by TGA, XRD, DRS, ATR-FTIR, nitrogen adsorption/desorption isotherm, zeta potential, SEM, and TEM. The major operational conditions were optimized for catalyst or adsorbent mass, pH, shaking time, initial amoxicillin (AMX) concentration, power of UV lamp, and temperature. The results illuminated that NTP achieved the highest adsorption capacity (88.46 mg/g) at 20 ℃ and AMX adsorption onto all the solid materials was well applied by Langmuir, Temkin, pseudo-second order, and Elovich models. The maximum desorption percent (98%) was attained by acetone. The degradation percent of AMX reached 85.3 and 99.5% for NT and NTP, respectively, using 0.9 g/L of catalyst dosage through 90 min. AMX photodegradation onto the catalysts' surface was well fitted by Langmuir-Hinshelwood, Arrhenius, and Eyring-Polanyi models with endothermic, physical, and nonspontaneous nature of photocatalysis process. NTP acts as a promising adsorbent and photocatalyst for the antibiotics' removal in wastewater.

The Influence of Oxidation and Nitrogenation on the Physicochemical Properties and Sorption Capacity of Activated Biocarbons Prepared from the Elderberry Inflorescence

The main objective of the study was to prepare a series of new activated biocarbons by means of physical and chemical activation of elderberry inflorescence. The influence of carbon matrix nitrogenation/oxidation on the physicochemical properties and sorption abilities of the carbonaceous materials was investigated. The impact of initial dye concentration, pH and temperature of the system on methylene blue and rhodamine B removal efficiency was checked. It was shown that activation of elderberry inflorescences with CO₂ or H₃PO₄, and their further modification by introducing nitrogen or oxygen functional groups, allowed us obtain a wide range of materials that differ significantly in terms of the chemical nature of the surface, degree of specific surface development and the type of porous structure generated. The samples prepared by chemical activation proved to be very effective in terms of cationic dyes adsorption. The maximum sorption capacity toward methylene blue and rhodamine B reached the level of 277.8 and 98.1 mg/g, respectively. A better fit to the experimental data was achieved with a Langmuir isotherm than a Freundlich one. It was also shown that the efficiency of methylene blue and rhodamine B adsorption from aqueous solutions decreased with increasing temperature of the system.

Novel synthesis of siligraphene/tungstates (g-SiC/AWO) with promoted transportation of photogenerated charge carriers via direct Z-scheme heterojunctions

We developed here the efficient photocatalysts for the removal of high concentrations of tetracycline under visible light by immobilizing the AWO (A = Ag, Bi, Na) nanocrystals on the surface of siligraphene (g-SiC) nanosheets. The g-SiC/AWO composites was synthesized by magnesiothermic synthesis of g-SiC and sonochemical immobilization of tungstates. These new heterojunctions of g-SiC/tungstates show superior photocatalytic activities in the degradation of high concentrations of tetracycline and 97, 98, and 94% of tetracycline were removed by using low amounts of g-SiC/Ag₂WO₄, g-SiC/Bi₂WO₆, and g-SiC/Na₂WO₄ catalysts, respectively. Based on band structures, the band gaps reduce and the photocatalytic activities were extremely enhanced due to the shortening of electron transfer distance through the Z-scheme mechanism. Also, the graphenic structure of g-SiC is another parameter that was effective in improving photocatalytic performance by increasing the electron transfer and decreasing the rate of electron-hole recombination. Furthermore, the π back-bonding of g-SiC with metal atoms increases the electron-hole separation to enhance the photocatalytic activity. Interestingly, g-SiC composites (g-SiC/AWO) showed much higher photocatalytic properties compared to graphene composites (gr/AWO) and can remove the tetracycline even at dark by producing the oxygenated radicals via adsorption of oxygen on the positive charge of Si atoms in siligraphene structure.

Carbon Adsorbents Obtained from Pistachio Nut Shells Used as Potential Ingredients of Drinking Water Filters

Water resources are increasingly degraded due to the discharge of waste generated in municipal, industrial and agricultural areas. Therefore, the search for new materials enabling the effective treatment of drinking water and sewage is currently of great interest. This paper deals with the adsorption of organic and inorganic pollutants on the surface of carbonaceous adsorbents prepared by thermochemical conversion of common pistachio nut shells. The influence of the direct physical activation with CO2 and chemical activation with H3PO4 on parameters, such as elemental composition, textural parameters, acidic-basic character of the surface as well as electrokinetic properties of the prepared carbonaceous materials was checked. The suitability of the activated biocarbons prepared as the adsorbents of iodine, methylene blue and poly(acrylic acid) from the aqueous solutions was estimated. The sample obtained via chemical activation of the precursor turned out to be much more effective in terms of all the tested pollutants adsorption. Its maximum sorption capacity toward iodine was 1059 mg/g, whereas in relation to methylene blue and poly(acrylic acid) 183.1 mg/g and 207.9 mg/g was achieved, respectively. For both carbonaceous materials, a better fit to the experimental data was achieved with a Langmuir isotherm than a Freundlich one. It has also been shown that the efficiency of organic dye, and especially anionic polymer adsorption from aqueous solutions, is significantly affected by solution pH and temperature of the adsorbate-adsorbent system.

Adsorption and Desorption Study of Reusable Magnetic Iron Oxide Nanoparticles Modified with Justicia adhatoda Leaf Extract for the Removal of Textile Dye and Antibiotic

The release of tetracycline hydrochloride (TCH) and methylene blue (MB) dye into the aquatic system uncontrollably caused major environmental and health problems; hence, their prevention required serious attention. Adsorption process is now being researched in order to increase adsorption efficiency and reprocess to alleviate environmental issues. The use of magnetic nanoparticle as an adsorbent for wastewater treatment has a lot of prospective. A magnetic iron oxide nanoparticle surface modified by Vasaka (Justicia adhatoda) leaf extract (JA-MIONs) is used to give a fast removal approach for MB dye and TCH antibiotics. Dynamic light scattering, UV-Vis and band gap measurement, powder X-ray diffraction, Fourier-transform infrared spectroscopy, and transmission electron microscopy were operated to analyse the formation and size of these magnetic nanoparticles. The impacts of different factors such as contact time (30-150 min), adsorbate concentration (10-50 mg/L), pH (4-10), and adsorbent dose (2-10 mg) were explored. Adsorption kinetics and isotherms show that it follows the pseudo-first-order kinetic and the Freundlich isotherm, with maximum adsorption capacities of 76.92 mg/g for MB and 200 mg/g for TCH at 298 K. The reusability of the JA-MIONs eventually exhibited a decline in the adsorption percentage of MB and TCH after five and four times respectively. After the desorption-adsorption cycles, this adsorbent continued to exhibit significant adsorption capacity. This investigation furnished the significant reference data for the synthesis of JA-MIONs as a novel and auspicious adsorbent for the industrial clean-up of toxic dyes and heavily used antibiotics from water.

Graphical abstract

Modification of Chlorella vulgaris carbon with Fe3O4 nanoparticles for tetracycline elimination from aqueous media

Tetracycline (TTC) is an antibiotic commonly prescribed to treat bacterial infections in animals and humans because of its low toxicity and antibacterial activity. This study focuses on the removal of TTC from an aqueous media using an activated carbon of Chlorella vulgaris modified with Fe₃O₄ magnetic composite (ACCV/Fe₃O₄ mc). The isothermal and kinetic models were studied to understand the adsorption mechanism. The Box-Behnken model was used for experimental design, and the main research parameters were ACCV/Fe₃O₄ mc mass (0.2-0.8 g/L), reaction time (10-60 min), TTC concentration (5-30 mg/L), and pH (3-11). The highest TTC removal rate of 90.47% was obtained at a pH of 7, a time of 60 min, an ACCV/Fe₃O₄ mc mass of 0.5 g/L, and an antibiotic concentration of 5 mg/L. TTC removal was fitted with the pseudo-second-order and the Langmuir model. The Langmuir adsorption capacity of TTC was computed to be 26.18 mg/g. The results show that the ACCV/Fe₃O₄ mc adsorbent significantly removes TTC from the aqueous solution.

Adsorptive removal of antibiotic pollutants from wastewater using biomass/biochar-based adsorbents

This study explores adsorptive removal measures to shed light on current water treatment innovations for kinetic/isotherm models and their applications to antibiotic pollutants using a broad range of biomass-based adsorbents. The structure, classifications, sources, distribution, and different techniques for the remediation of antibiotics are discussed. Unlike previous studies, a wide range of adsorbents are covered and adsorption of comprehensive classes of antibiotics onto biomass/biochar-based adsorbents are categorized as β-lactam, fluoroquinolone, sulfonamide, tetracycline, macrolides, chloramphenicol, antiseptic additives, glycosamides, reductase inhibitors, and multiple antibiotic systems. This allows for an assessment of their performance and an understanding of current research breakthroughs in applying various adsorbent materials for antibiotic removal. Distinct from other studies in the field, the theoretical basis of different isotherm and kinetics models and the corresponding experimental insights into their applications to antibiotics are discussed extensively, thereby identifying the associated strengths, limitations, and efficacy of kinetics and isotherms for describing the performances of the adsorbents. In addition, we explore the regeneration of adsorbents and the potential applications of the adsorbents in engineering. Lastly, scholars will be able to grasp the present resources employed and the future necessities for antibiotic wastewater remediation.

Equilibrium, kinetics, and thermodynamics study on the biosorption of reactive levofloxacin antibiotic on Pithophora macroalgae in aqueous solution

Since untreated wastewater from hospitals and residential areas is being discharged directly into surface waterways, pharmaceutical contaminants have been shown to be higher in many countries. Therefore, the development of novel and effective techniques to extract antibiotic substances from wastewater is of utmost importance. The present work aims at the use of green Pithophora macroalgae to remove levofloxacin antibiotic from an aqueous solution through biosorption. Biosorption is an economical and eco-friendly method for treating wastewater. The macroalgae were dried, grounded, and used as biosorbent to remove the levofloxacin (LVX) antibiotics from the aqueous solution. The influence of operating conditions such as initial antibiotic concentration, biosorbent dosage, agitation speed, pH, and temperature was studied. The biosorbent was characterized by FTIR, SEM, and point zero charge. The experimental data were evaluated using Langmuir and Freundlich isotherms. The experimental data best fit the Freundlich isotherm model (R² = 0.969), while the kinetic model for the experiment follows the pseudo-second-order (R² = 0.998) with a maximum biosorption capacity of 17.8 mg/g. Maximized removal of LVX occurs at favorable conditions of 298 K temperature, 150 mg/L initial concentration of antibiotic, 0.5 g sorbent dose, and 6.5 pH. The calculated thermodynamic parameters reveal that the biosorption of LVX antibiotics occurs by an endothermic process. This study deduces that Pithophora macroalgae biomass proved to be an effective biosorbent for biosorption of LVX antibiotics and may be a novel alternative method for antibiotics removal from aqueous solutions.

Adsorptive removal of levofloxacin and antibiotic resistance genes from hospital wastewater by nano-zero-valent iron and nano-copper using kinetic studies and response surface methodology

In the twenty-first century, water contamination with pharmaceutical residues is becoming a global phenomenon and a threat. Antibiotic residues and antibiotic resistance genes (ARGs) are recognized as new emerging water pollutants because they can negatively affect aquatic ecosystems and human health, thereby posing a complex environmental problem. These nano-adsorbents of the next generation can remove these pollutants at low concentrations. This study focuses on the chemical synthesis of copper oxide nanoparticles (CuONPs) and nano-zero-valent iron (nZVI) used as nano-adsorbents for levofloxacin removal from water samples and antibiotic-resistant genes. The CuONPs and nZVI are initially characterized by transmission electron microscopy, scanning electron microscopy, and X-ray diffraction. The levofloxacin adsorption isotherm on the CuONPS and nZVI shows the best fit with the Langmuir isotherm model, exhibiting correlation coefficients (R2) of 0.993 and 0.999, respectively. The adsorption activities of CuONPS and nZVI were fitted to a pseudo-second-order kinetic model with correlation coefficients (R2) of 0.983 and 0.994, respectively. The maximum levofloxacin removal capacity was observed at (89%), (84%), (89%), (88%) and (71.6) at pH 7 and adsorbent dose(0.06 mg/L), initial LEV concentration (1 mg/L), temperature 25 °C, and contact time 120 min for CuONPs. Removal efficiency was (91%), (90.6%), (91%), (89%), and (80%), at pH 7, adsorbent dose(0.06), initial LEV concentration (1 mg/L), temperature 35 °C, and contact time 120 min. The levofloxacin adsorption is an exothermic process for nZVI and CuONPs, according to thermodynamic analysis. A thermodynamic analysis indicated that each adsorption process is spontaneous. Several genera, including clinically pathogenic bacteria (e.g., Acinetobacter_baumannii, Helicobacter_pylori, Escherichia_coli, Pseudomonas_aeruginosa, Clostridium_beijerinckii, Escherichia/Shigella_coli, Helicobacter_cetorum, Lactobacillus_gasseri, Bacillus_cereus, Deinococcus_radiodurans, Rhodobacter_sphaeroides, Propionibacterium_acnes, and Bacteroides_vulgatus) were relatively abundant in hospital wastewater. Furthermore, 37 antibiotic resistance genes (ARGs) were quantified in hospital wastewater. The results demonstrated that 95.01% of nZVI and 91.4% of CuONPs are effective adsorbents for removing antibiotic-resistant bacteria from hospital effluent. The synthesized nZVI and CuONPs have excellent reusability and can be considered cost effective and eco-friendly adsorbents.

Pharmaceutical residues: One of the significant problems in achieving 'clean water for all' and its solution

With the rapid emergence of various metabolic and multiple-drug-resistant infectious diseases, new pharmaceuticals are continuously being introduced in the market. The excess production and use of pharmaceuticals and their untreated/unmetabolized release in the environment cause the contamination of aquatic ecosystem, and thus, compromise the environment and human-health. The present review provides insights into the classification, sources, occurrence, harmful impacts, and existing technologies to curb these problems. A comprehensive detail of various biological and nanotechnological strategies for the removal of pharmaceutical residues from water is critically discussed focusing on their efficiencies, and current limitations to design improved-technologies for their lab-to-field applications. Furthermore, the review highlights and suggests the scope of integrated bionanotechnological methods for enhanced removal of pharmaceutical residues from water to fulfill the United Nations Sustainable Development Goal (UN-SDG) for providing clean potable water for all.

Adsorptive removal of tetracycline and ciprofloxacin drugs from water by using a magnetic rod-like hydroxyapatite and MIL-101(Fe) metal-organic framework nanocomposite

A novel porous nanocomposite composed of hydroxyapatite nanorods (HAP), a MIL-101(Fe) metal-organic framework, and Fe₃O₄ nanoparticles was successfully fabricated in this work. The magnetic HAP/MIL-101(Fe)/Fe₃O₄ ternary nanocomposite was identified by various techniques, namely FT-IR spectroscopy, XRD, Raman spectroscopy, SEM, EDX, TEM, BET specific surface area, zeta potential, and VSM measurements. Tetracycline (TC) and ciprofloxacin (CIP) aqueous solutions were used to evaluate the adsorption performance of the resulting HAP/MIL-101(Fe)/Fe₃O₄ composite. The adsorption rate and capacity of HAP/MIL-101(Fe)/Fe₃O₄ were increased as compared with HAP, MIL-101(Fe), and HAP/MIL-101(Fe) samples due to the increased attraction. The influence of initial drug concentration, adsorbent dosage, temperature, and pH on the adsorption process was investigated. The results showed that the removal efficiencies of HAP/MIL-101(Fe)/Fe₃O₄ for TC and CIP were 95% and 93%, under the determined optimum conditions: pH of 7, drug concentration of 50 mg L^-1, adsorbent dosage of 30 mg, and temperature of 25 °C. The maximum adsorption capacities of HAP/MIL-101(Fe)/Fe₃O₄ for TC and CIP were 120.48 mg g^-1 and 112.35 mg g^-1, respectively. Reusability of the prepared nanocomposite was easily achieved up to three times without significant change in its structure. As a result, the synthesized magnetic nanocomposite can be reused as a suitable absorbent for TC and CIP removal from aqueous solutions.

TiO2-immobilized porous geopolymer composite membrane for removal of antibiotics in hospital wastewater

This experimental research proposes an environment-friendly and low-cost porous geopolymer composite membrane (PGCM) to treat antibiotics in hospital wastewater. The proposed PGCM consisted of two layers: a porous support layer and a dense coating layer. The dense coating layer was synthesized by incorporating variable TiO₂ content (0, 2, 6, and 10 wt%) into the geopolymer matrix. The dense coating layer was of hierarchical mesoporous structure with 700 μm in thickness and adhered to the porous support layer. The average pore size, total pore volume, and open porosity of the dense coating layer decreased with an increase in TiO₂, resulting in reduced water permeability. The PGCM was applied to remove six target antibiotics including amoxicillin, ciprofloxacin, norfloxacin, sulfamethoxazole, tetracycline, and trimethoprim in real hospital wastewater. By comparison, the PGCM with 10 wt% TiO₂ achieved the highest antibiotic removal efficiencies, with the adsorption and combined adsorption/photodegradation removal efficiencies for the target antibiotics of 38-75% and 74-86%, respectively. The novelty of this research lies in the use of a tailor-made porous geopolymer composite membrane incorporated with TiO₂ photooxidation as a single-step treatment of recalcitrant antibiotics contained in hospital wastewater.

The Dual Roles of Nano Zero-Valent Iron and Zinc Oxide in Antibiotics Resistance Genes (ARGs) SPREAD in Sediment

Nanoparticles (NPs) are widely used and ubiquitous in the environment, but the consequences of their release into the environment on antibiotics resistance genes (ARGs), microbial abundance, and community, are largely unknown. Therefore, this study examined the effect of nano zero-valent iron (nZVI) and zinc oxide (nZnO) on tetracycline resistance genes (tet-ARGs) and class 1 integron (intI1) in sediment under laboratory incubation. The coexistence of NPs and tetracycline (TC) on tet-ARGs/intI1 was also investigated. It was found that nZVI and nZnO promoted tet-ARGs/intI1 abundance in sediment without TC but reduced the inducing effect of TC on tet-ARGs/intI1 in sediment overlaid with TC solution. Without TC, nZVI, intI1, and the bacterial community could directly promote tet-ARGs spread in nZVI sediment, while intI1 and bacterial abundance were the most directly important reasons for tet-ARGs spread in nZnO sediment. With TC, nZVI and bacterial community could reduce tet-ARGs abundance in nZVI sediment, while nZnO and bacterial community could directly promote tet-ARGs in nZnO sediment. Finally, these findings provided valuable information for understanding the role of NPs in promoting and reducing ARGs in the environment.

New nanostructured activated biochar for effective removal of antibiotic ciprofloxacin from wastewater: Adsorption dynamics and mechanisms

Developing green inexpensive and effective adsorbents is critically needed for elimination of antibiotics from contaminated water. The current study assessed the nanostructured activated biochar (nPPAB) derived from pomegranate peels (PP) as a promising sorbent for efficient removal of the antibiotic ciprofloxacin (CIP). The results affirm that the second order and Langmuir models fit well to adsorption kinetics and equilibrium data respectively. The nPPAB adsorption capacity of Langmuir (q_max) for CIP was 142.86 mg g^-1 which is 26.85 times greater than that of bulk PP. Hydrogen bonding, π-π interaction, hydrophobic and electrostatic interactions are the dominant mechanisms of CIP adsorption by nPPAB. The efficiency of nPPAB for CIP removal from real wastewater using batch and packed-bed reactor were 89.94 and 84.74% respectively. This study clearly demonstrated the substantial capacity of nPPAB as an ecofriendly, feasible, and in-expensive adsorbent for successful elimination of CIP from wastewater.

Synthesis of silver nanoparticles from red and green parts of the pistachio hulls and their various in-vitro biological activities

In this study, synthesis of silver nanoparticles (AgNPs) was carried out utilizing the red and green parts of the pistachio hulls then their several biological activities were investigated. The DPPH (2,2-diphenyl-1-picryl-hydrazyl-hydrate) activities of the AgNPs synthesized from red pistachio hulls extracts (PhR-AgNPs) and green pistachio hulls extracts (PhG-AgNPs) were investigated. The DPPH scavenging capability at 200 mg/L concentration of PhR-AgNPs was around 93.01% however PhG-AgNPs displayed 91.00%. The synthesized PhR-AgNPs and PhG-AgNPs acted on the E. coli plasmid DNA, causing its complete degradation and exhibiting effective chemical nuclease activity. Furthermore, PhR-AgNPs and PhG-AgNPs showed quite good antimicrobial activity against the studied strains with a range of the minimum inhibition concentration (MIC) of 8-16 mg/L. Moreover, it was observed that both pistachio hulls coated with AgNPs were highly effective in inhibiting the biofilm generation studied strains. Moreover, PhR-AgNP and PhG-AgNP displayed a completely inhibition effect on cellular viability of E. coli with 100% at 125 mg/L.

Relevance of sorption in bio-reduction of amoxicillin taking place in forest and crop soils

The fate of antibiotics reaching soils is a matter of concern, given its potential repercussions on public health and the environment. In this work, the potential bio-reduction of the antibiotic amoxicillin (AMX), affected by sorption and desorption, is studied for 17 soils with clearly different characteristics. To carry out these studies, batch-type tests were performed, adding increasing concentrations of AMX (0, 2.5, 5, 10, 20, 30, 40, and 50 μmol L^-1) to the soils. For the highest concentration added (50 μmol L^-1), the adsorption values for forest soils ranged from 90.97 to 102.54 μmol kg^-1 (74.21-82.41% of the amounts of antibiotic added), while the range was 69.96-94.87 μmol kg^-1 (68.31-92.56%) for maize soils, and 52.72-85.40 μmol kg^-1 (50.96-82.55%) for vineyard soils. When comparing the results for all soils, the highest adsorption corresponded to those more acidic and with high organic matter and non-crystalline minerals contents. The best adjustment to adsorption models corresponded to Freundlich's. AMX desorption was generally <10%; specifically, the maximum was 6.5% in forest soils, and 16.9% in agricultural soils. These results can be considered relevant since they cover agricultural and forest soils with a wide range of pH and organic matter contents, for an antibiotic that, reaching the environment as a contaminant, can pose a potential danger to human and environmental health.

The potential application of bio-based ceramic/organic xerogel derived from the plant sources: A new green adsorbent for removal of antibiotics from pharmaceutical wastewater

A bio-based ceramic/organic xerogel (BCO-xerogel) was obtained from the combination of sugarcane bagasse ash, polyvinyl alcohol, and pine cone-derived tannin extract, which are abundant, non-toxic, and renewable sources. The as-prepared BCO-xerogel was used as a low-cost green adsorbent for the eliminate of four types of the most widely used antibiotics, including amoxicillin (AMX), tetracycline (TC), cefalexin (CLX), and penicillin G (PEN G) residuals from contaminated water. The simultaneous effects conventional variables including adsorbent dosage, antibiotic concentrations, solution pH, and contact time were studied and optimized by central composite design (CCD) under response surface methodology (RSM). Analysis of variance (ANOVA) was employed as a statistical formula to determine the significance of operating environmental conditions and their interactions with 95% confidence limits. Under optimized conditions, the experimental removal efficiencies for AMX, TC, CLX, and PEN G were 98.78 ± 3.25, 99.12 ± 2.52, 98.02 ± 1.98, and 98.42 ± 2.19, respectively. The adsorption isotherms and kinetics were better fitted with Langmuir and pseudo-second-order models, respectively. Thermodynamic studies showed that the adsorption process was endothermic, spontaneous, and occurred by combination of physical and chemical mechanisms. Also, evaluating the ability of BCO-xerogel to adsorptive removal of AMX, TC, CLX, and PEN G antibiotics in real wastewaters showed about 97.4-98.6% adsorption efficiency in river water and about 67.1-71.3% in three hospital effluents. After the adsorption process, the antibiotic-loaded adsorbent was regenerated by NaOH (0.01 mol L^-1), and the reusability tests showed that the removal efficiencies of the antibiotics in the four recovery steps were still above 90%. This work explored the development of green, efficient, and economical bio-adsorbent that can be utilized for the removal of antibiotics from contaminated wastewaters.

Amoxicillin Retention/Release in Agricultural Soils Amended with Different Bio-Adsorbent Materials

The antibiotic amoxicillin (AMX) may reach soils and other environmental compartments as a pollutant, with potential to affect human and environmental health. To solve/minimize these hazards, it would be clearly interesting to develop effective and low-cost methods allowing the retention/removal of this compound. With these aspects in mind, this work focuses on studying the adsorption/desorption of AMX in different agricultural soils, with and without the amendment of three bio-adsorbents, specifically, pine bark, wood ash and mussel shell. For performing the research, batch-type experiments were carried out, adding increasing concentrations of the antibiotic to soil samples with and without the amendment of these three bio-adsorbents. The results showed that the amendments increased AMX adsorption, with pine bark being the most effective. Among the adsorption models that were tested, the Freundlich equation was the one showing the best fit to the empirical adsorption results. Regarding the desorption values, there was a decrease affecting the soils to which the bio-adsorbents were added, with overall desorption not exceeding 6% in any case. In general, the results indicate that the bio-adsorbents under study contributed to retaining AMX in the soils in which they were applied, and therefore reduced the risk of contamination by this antibiotic, which can be considered useful and relevant to protect environmental quality and public health.

Sustainable green nanoadsorbents for remediation of pharmaceuticals from water and wastewater: A critical review

In the last three decades, pharmaceutical research has increased tremendously to offer safe and healthy life. However, the high consumption of these harmful drugs has risen devastating impact on ecosystems. Therefore, it is worldwide paramount concern to effectively clean pharmaceuticals contaminated water streams to ensure safer environment and healthier life. Nanotechnology enables to produce new, high-technical material, such as membranes, adsorbent, nano-catalysts, functional surfaces, coverages and reagents for more effective water and wastewater cleanup processes. Nevertheless, nano-sorbent materials are regarded the most appropriate treatment technology for water and wastewater because of their facile application and a large number of adsorbents. Several conventional techniques have been operational for domestic wastewater treatment but are inefficient for pharmaceuticals removal. Alternatively, adsorption techniques have played a pivotal role in water and wastewater treatment for a long, but their rise in attraction is proportional with the continuous emergence of new micropollutants in the aquatic environment and new discoveries of sustainable and low-cost adsorbents. Recently, advancements in adsorption technique for wastewater treatment through nanoadsorbents has greatly increased due to its low production cost, sustainability, better physicochemical properties and high removal performance for pharmaceuticals. Herein, this review critically evaluates the performance of sustainable green nanoadsorbent for the remediation of pharmaceutical pollutants from water. The influential sorption parameters and interaction mechanism are also discussed. Moreover, the future prospects of nanoadsorbents for the remediation of pharmaceuticals are also presented.

Magnetic alginate/glycodendrimer beads for efficient removal of tetracycline and amoxicillin from aqueous solutions

The release of antibiotic drugs into aquatic environments is a serious environmental and health problem in recent years. Therefore, the development of potential adsorbents for the effective removal of tetracycline (TC) and amoxicillin (AMX) of aqueous media is of great importance. In this study, new alginate beads were successfully prepared by encapsulation of Fe₃O₄@maltose-functionalized triazine dendrimer in alginate (Alg/Fe₃O₄@C@TD) for the first time. The obtained beads were utilized as a well adsorbent for the removal of TC and AMX antibiotics from aqueous solutions by batch adsorption procedure. The characteristics of the synthesized beads were investigated using FT-IR, Zeta potential, SEM, XRD, EDX, VSM, and BET. The effects of various operation factors such as adsorbent dose, pH of the solution, contact time, antibiotic initial concentration, temperature, and ionic strength on the removal of antibiotics were studied. Moreover, Langmuir and Freundlich adsorption isotherm results showed that the Langmuir model fitted well for the adsorption of both antibiotics onto Alg/Fe₃O₄@C@TD beads. Based on the Langmuir model, the maximum adsorption capacity of TC and AMX onto Alg/Fe₃O₄@C@TD beads at 25 °C was 454.54 and 400 mg/g, respectively. Kinetic and thermodynamic studies also indicated that the TC and AMX adsorption were found to be well fitted with a pseudo-second-order kinetic model, feasible, endothermic, and spontaneous in nature. In addition, the Alg/Fe₃O₄@C@TD beads showed excellent reusability for removal from both antibiotics after six adsorption cycles. Overall, the obtained results suggest that Alg/Fe₃O₄@C@TD beads could be considered as a low-cost and eco-friendly adsorbent for antibiotic contaminants removal from aquatic media.

Low-Cost and Eco-Friendly Hydroxyapatite Nanoparticles Derived from Eggshell Waste for Cephalexin Removal

This work describes the hydroxyapatite nanoparticle (HAP) preparation from eggshell waste and their application as an adsorbent for Cephalexin (Ceph) antibiotic removal from aqueous solutions. Chemical precipitation with phosphoric acid was used to evaluate the feasibility of calcium oxide for HAP preparation. The structural properties of HAP were characterized by X-ray diffraction, which revealed the formation of the hydroxyapatite crystalline phase formation. In addition, transmitting electron spectroscopy showed an irregular shape with a variation in size. The impact of various experimental conditions on the removal efficiency such as the solution’s pH, contact time, HAP mass, solution temperature, and Ceph concentration were studied. Experimental data showed that HAP could remove most Ceph species from aqueous solutions within 1 h at pH = 7 with 70.70% adsorption efficiency utilizing 50 mg of the HAP. The removal process of Ceph species by HAP was kinetically investigated using various kinetic models, and the results showed the suitability of the pseudo-second-order kinetic model for the adsorption process description. Moreover, the removal process was thermodynamically investigated; the results showed that the removal was spontaneous endothermic and related to the randomness increase. The data confirmed that HAP had high efficiency in removing Ceph antibiotics from an aqueous solution.

Biosynthesis of SiO2 nanoparticles using extract of Nerium oleander leaves for the removal of tetracycline antibiotic

Tetracycline (TC) is one of the antibiotics that is found in wastewaters. TC is toxic, carcinogenic, and teratogenic. In this study, the tetracycline was removed from water by adsorption using dioxide silicon nanoparticles (SiO₂ NPs) biosynthesized from the extract of Nerium oleander leaves. These nanoparticles were characterized using SEM-EDX, BET-BJH, FTIR-ATR, TEM, and XRD. The influences of various factors such as pH solution, SiO₂ NPs dose, adsorption process time, initial TC concentration, and ionic strength on adsorption behaviour of TC onto SiO₂ NPs were investigated. TC adsorption on SiO₂ NPs could be well described in the pseudo-second-order kinetic model and followed the Langmuir isotherm model with a maximum adsorption capacity was 552.48 mg/g. At optimal conditions, the experimental adsorption results indicated that the SiO₂ NPs adsorbed 98.62% of TC. The removal of TC using SiO₂ NPs was 99.56% at conditions (SiO₂ NPs dose = 0.25 g/L, C₀ = 25 mg/L, and t = 40 min) based on Box-Behnken design (BBD) combined with response surface methodology (RSM) modelling. Electrostatic interaction governs the adsorption mechanism is attributed. The reusability of SiO₂ NPs was tested, and the performance adsorption was 85.36% after the five cycles. The synthesized SiO₂ NPs as promising adsorbent has a potential application for antibiotics removal from wastewaters.

Understanding the factors affecting adsorption of pharmaceuticals on different adsorbents - A critical literature update

Remediation of emerging pharmaceutically active compounds (PhACs) as micropollutants in wastewater is of foremost importance as they can cause extremely detrimental effects on life upon bioaccumulation and generation of drug-resistance microorganisms. Presently used physicochemical treatments, such as electrochemical oxidation, nanofiltration and reverse osmosis, are not feasible owing to high operating costs, incomplete removal of contaminants along with toxic by-products formation. Adsorption with the utilization of facile and efficient nanoparticulate adsorbents having distinctive properties of high surface area, excellent adsorption capacity, ability to undergo surface engineering and good regeneration displays great potential in this aspect along with the incorporation of nanotechnology for effective treatment. The application of such nanosorbents provides optimal performance under a wide range of physicochemical conditions, decreased secondary pollution with reduced mechanical stress along with excellent organic compound sequestration capacity, which in turn improves the quality of potable water in a sustainable way compared to current treatments. The present review intends to consolidate the range of factors that affect the process of adsorption of different PhACs on to various nanosorbents and also highlights the adsorption mechanism aiding in the retrieval.

Adsorption and detoxification of pharmaceutical compounds from wastewater using nanomaterials: A review on mechanism, kinetics, valorization and circular economy

Antibiotics overuse, inappropriate conduct, and discharge have led to adverse effects on various ecosystems. The occurrence of antibiotics in surface and drinking water is a matter of global concern. It is responsible for multiple disorders, including disruption of endocrine hormones and high chronic toxicity. The hospitals, pharmaceutical industries, households, cattle farms, and aquaculture are the primary discharging sources of antibiotics into the environment. This review provides complete detail on applying different nanomaterials or nanoparticles for the efficient removal of antibiotics from the diverse ecosystem with a broader perspective. Efforts have been made to focus on the degradation pathways and mechanism of antibiotic degradation using nanomaterials. More light has been shed on applying nanostructures in photocatalysis, which would be an economical and efficient solution. The nanoscale material or nanoparticles have incredible potential for mineralizing pharmaceutical compounds in aqueous solutions at low cost, easy handling characteristics, and high efficacy. Furthermore, nanoparticles can absorb the pharmaceutical by-products and wastes at a minimum cost as they can be easily recycled. With the increasing number of research in this direction, the valorization of pharmaceutical wastes and by-products will continue to expand as we progress from old conventional approaches towards nanotechnology. The utilization of nanomaterials in pharmaceutical wastewater remediation is discussed with a major focus on valorization, energy generation, and minimization and its role in the circular economy creating sustainable development.

Alternanthera spp. based-phytoremediation for the removal of acetaminophen and methylparaben at mesocosm-scale constructed wetlands

Recently, the spread of pharmaceuticals and personal care products (PPCPs) in the aquatic environment has steadily increased. In this study, phytoremediation technology, using an ornamental plant (Alternanthera spp.), was investigated to improve the removal of acetaminophen (AC) and methylparaben (MP) from a synthetically prepared wastewater. Three exposure lines (AC-line, MP-line and control-line) were performed with a total of 26 subsurface-horizontal constructed wetlands (SSH-CWs) that operated in batch feeding mode. The influence of plants in addition to the initial spiking concentration (20, 60 and 100 mg/L) of AC and MP on the removal efficiency was evaluated throughout the 35-days experiments. The highest removal efficiencies for AC and MP were 88.6% and 66.4%, respectively, achieved in the planted CWs; whereas only 29.7% and 21.9% were achieved in the control CWs for AC and MP, respectively. The results confirmed the role of Alternanthera spp. for accelerating the removal of AC and MP from synthetically contaminated wastewater in CWs.

Novel plantain peel activated carbon-supported zinc oxide nanocomposites (PPAC-ZnO-NC) for adsorption of chloroquine synthetic pharmaceutical used for COVID-19 treatment

Chloroquine has been reported as an effective drug for the treatment of COVID-19 and with the rise in its administration and continued use, metabolites of chloroquine invariably find their way into the environment. There are many concerns recently on the presence of pharmaceuticals in the aquatic environment, hence the need for environmental remediation via effective adsorbent. Plantain peel activated carbon-supported zinc oxide (PPAC-ZnO) nanocomposite was prepared and characterized using physicochemical and spectroscopic techniques. The rate of uptake of chloroquine by PPAC-ZnO nanocomposite was investigated by batch technique under different operational parameters. PPAC-ZnO nanocomposite was characterized by various physicochemical techniques by SBET = 606.07 m2g-1, pH(pzc) = 4.98 surface area by Saer's method = 273.4 m2g-1. The carboxylic, phenols, lactone, and basic sites were determined by the Boehm method. Chloroquine uptake was confirmed by FTIR and SEM before and after adsorption. Change in morphology after adsorption was revealed by scanning electron microscopy (SEM). X-ray diffraction (XRD) showed the crystallinity of PPAC-ZnO nanocomposite. The batch adsorption experiment results showed that adsorption capacity increased with an increase in temperature. The maximum chloroquine sorption was 78.89% at a concentration of 10 ppm and a temperature of 313 K. Equilibrium sorption fitted well to Langmuir and Temkin isotherms with a high correlation coefficient (R 2) of 0.99. Pseudo-second-order best described the kinetic data and adsorption mechanism was pore diffusion dependent. Thermodynamics parameters (ΔG =  - 25.65 to - 28.79 kJmol-1; ΔH = 22.06 kJmol-1 and ΔS = 157.69 Jmol-1) demonstrated feasibility, spontaneity, and endothermic behavior of the process with degrees of randomness. The activation energy for adsorption was less than 40 kJmol-1 suggesting a physisorption mechanism. This study results revealed that PPAC-ZnO nanocomposites are a sustainable and effective adsorbent for the removal of pharmaceutical waste.

Controlled surface functionalization of Ni-S nanostructures for pH-responsive selective and superior pollutants adsorption

Herein, we developed a synthetic strategy to functionalize Ni-S nanostructures (NS) using a facile precipitation method at moderate temperature. The surface functionality of NS is controlled by varying amount of mixed surfactants to achieve the pH-responsive selective adsorption of anionic and cationic dyes and the adsorption of ciprofloxacin (CIP) and tetracycline (TC) antibiotics. Powder XRD diffraction pattern revealed the phase of NS was changed from α-NiS to mixed phases after functionalization. The surface area of functionalized NS was significantly enhanced by ~5 times of that unfunctionalized NS as 6.6 m²g^-1 to 30.3 m²g^-1. The NS selectively adsorbed methyl orange (MO) at pH 4.5 and methylene blue (MB) at pH 11.5 with separation efficiency values of 94.2% and 97.9% respectively. The maximum adsorption capacity for MO, MB, TC and CIP are obtained as 1526.3, 1031.2, 1540.8 and 632.4 mg g^-1, respectively. The electrostatic interaction is predominantly involved in the adsorption of dyes whereas adsorption of antibiotics changed to hydrogen bonding and metal coordination. Thermodynamics parameters indicated exothermic and spontaneous adsorption of dyes. The optimized adsorbent is easily recyclable. Thus, the developed strategy of functionalization of nanostructures unveils a practical approach towards selective and efficient adsorption of organic pollutants.

Removal of amoxicillin from wastewater in the presence of H2O2 using modified zeolite Y- MgO catalyst: An optimization study

In this paper, Zeolite-MgO was generated using alkali-thermal method and was utilized as a catalyst to decrease amoxicillin (AMX) concentration in the presence of H₂O₂ from wastewater. Different tests like Fourier-transform infrared (FTIR), Brunauer-Emmett-Teller (BET), field emission scanning electron microscopy-energy dispersive X-ray analysis (FESEM-EDX), thermogravimetric analysis (TGA), and X-ray diffraction (XRD) were done to determine catalyst properties. Active groups of C-S-C, CO, CC, C-N, C-O, N-O, and N-H were identified in catalyst frame. According to XRD results, lower crystallinity of nanoparticles after modification of zeolite by MgO can lead to improvement of AMX removal. Active surface of zeolite (2.32 m²/g) was increased after optimization by MgO to 2.96 m²/g, indicating an increase in the catalyst capacity for activation of H₂O₂. In addition, furnace temperature (200-500 °C), residence time in the furnace (1-4 h), and Mg(NO₃)₂: zeolite ratio (0.25: 2, 0.5:2, 1:2 w/w) were studied to achieve the optimized catalyst for AMX removal. Different parameters like pH (5-9), H₂O₂ concentration (0-6 mL/100 mL), dose of catalyst (0-10 g/L), AMX concentration (50-300 mg/L), and reaction time (10-130 min) were also studied. The best efficiency (97.9%) of AMX removal was achieved at acidic pH with the lowest amount of H₂O₂ (0.1 mL/100 mL) and 7 g/L of catalyst. AMX removal using the developed process followed pseudo-first-order kinetics. Reclaimable Zeolite-MgO catalyst can be effectively utilized in wastewater works.

Evaluating the Removal of the Antibiotic Cephalexin from Aqueous Solutions Using an Adsorbent Obtained from Palm Oil Fiber

This study aimed to understand the adsorption process of cephalexin (CPX) from aqueous solution by a biochar produced from the fiber residue of palm oil. Scanning electron microscopy, Fourier transform infrared spectroscopy, Boehm titration, and the point of zero charge were used to characterize the morphology and surface functional groups of the adsorbent. Batch tests were carried out to evaluate the effects of the solution pH, temperature, and antibiotic structure. The adsorption behavior followed the Langmuir model and pseudo-second-order model with a maximum CPX adsorption capacity of 57.47 mg g^-1. Tests on the thermodynamic behavior suggested that chemisorption occurs with an activation energy of 91.6 kJ mol^-1 through a spontaneous endothermic process. Electrostatic interactions and hydrogen bonding represent the most likely adsorption mechanisms, although π-π interactions also appear to contribute. Finally, the CPX removal efficiency of the adsorbent was evaluated for synthetic matrices of municipal wastewater and urine. Promising results were obtained, indicating that this adsorbent can potentially be applied to purifying wastewater that contains trace antibiotics.

Green synthesis of ZnO coated hybrid biochar for the synchronous removal of ciprofloxacin and tetracycline in wastewater

Preparation of biochar from kaolinite and coconut husk (KCB) and further activated with HCl (KCB-A) and KOH (KCB-B) via a microwave technique for the remediation of ciprofloxacin (CIP) and tetracycline (TET) from water was carried out. Characterization using scanning electron microscopy, energy dispersive X-ray, Fourier transform infrared spectroscopy and X-ray diffraction showed the successful synthesis of functionalized biochars. Batch adsorption experiments demonstrated the potential of the adsorbents for fast and efficient removal of CIP and TET from solution. The adsorption capacities were found to be 71, 140 and 229 mg g-1 for CIP and 118, 117 and 232 mg g-1 for TET removal on KCB, KCB-A and KCB-B, respectively. For KCB, KCB-B and KCB-B, CIP adsorption best followed the pseudo second order kinetic model (PSOM), pseudo first order kinetic model (PFOM) and intraparticle diffusion (IDP) respectively. TET adsorption followed PSOM for KCB, IPD for KCB-B and PFOM for KCB-A. CIP adsorption on KCB, KCB-A and KCB-B best fit the Temkin, Langmuir and Brouers-Sotolongo isotherms, respectively, and TET adsorption on KCB best fit Brouers-Sotolongo while KCB-A and KCB-B best fit Langmuir-Freundlich. Adsorption of both contaminants was thermodynamically feasible showing that these materials are excellent adsorbents for the treatment of pharmaceuticals in water.

Cotton textile waste valorization for removal of tetracycline and paracetamol alone and in mixtures from aqueous solutions: Effects of H3 PO4 as an oxidizing agent

The use of waste and by-products locally available in large quantities and at low cost as adsorbents can be considered an appropriate approach for improving waste management and protecting the environment. Cotton textile waste was used to prepare adsorbents (MC) via pyrolysis followed by a chemical modification with H₃ PO₄ . MC samples were characterized by scanning electron microscopy, FTIR spectroscopy, and N₂ adsorption-desorption isotherm. The results revealed that MC treated with 1 M H₃ PO₄ (MC₁ ) showed an excellent adsorption performance. The single and binary adsorption of tetracycline (TC) and paracetamol (Pa) onto MC₁ were studied. In a single system, TC was better adsorbed than Pa and maximum adsorption capacities q_m are 87.7 mg/g and 62 mg/g, respectively. The adsorption follows the Langmuir and pseudo-second-order kinetic models. For a binary system, the experimental data indicate that Pa (44.04 mg/g) is better adsorbed than TC (24.13 mg/g). Adsorption equilibrium data of TC and Pa evaluated by the selectivity extended-Langmuir model in which selectivity factor was introduced provided good correlation results with the binary adsorption data. Cotton textile waste is potentially promising for the preparation of effective adsorbents for the removal of pharmaceutical residues in aqueous solutions. PRACTITIONER POINTS: Valorization of cotton textile waste into adsorbents. Adsorbents were prepared by pyrolysis at 600°C followed by chemical modification in the presence of H₃ PO₄ . Removal of tetracycline (TC) and paracetamol (Pa) alone or in mixtures by adsorption. Adsorbent showed high-capacity adsorption of the TC and Pa even in a mixture from solutions at low concentrations. The Langmuir and selectivity extended-Langmuir models describe the adsorption of TC and Pa alone and in mixtures, respectively.