Analytical, thermodynamical and kinetic characteristics of photoluminescence immunosensor for the determination of Ochratoxin A

Photoluminescence-based biosensor for the detection of antibodies against SARS-CoV-2 virus proteins by ZnO tetrapod structure integrated within microfluidic system

This paper reports on development of an optical biosensor for the detection of antibodies against SARS-CoV-2 virus proteins in blood serum. ZnO nanotetrapods with high surface area and stable room temperature photoluminescence (PL) were selected as transducers. Structure and optical properties of the ZnO tetrapods have been studied by XRD, SEM and Raman spectroscopy. Crystallinity, dimensions and emission peaks of the ZnO tetrapods were determined. The ZnO tetrapods were fixed on glass chip. Silanization of ZnO tetrapods surface resulted in forming of functional surface groups suitable for the immobilization of bioselective layer. Two types of recombinant proteins (rS and rN) have been used to form bioselective layer on the surface of the ZnO tetrapods. Flow through microfluidic system, integrated with optical system, has been used for the determination of antibodies against SARS-CoV-2 virus proteins present in blood samples. The SARS-CoV-2 probes, prepared in PBS solution, have been injected into the measurement chamber with a constant pumping speed. Steady-state photoluminescence spectra and photoluminescence kinetics have been studied before and after injection of the probes. The biosensor signal has been tested to anti-SARS-CoV-2 antibodies in the range of 0.001 nM-1 nM. Control measurements have been performed with blood serum of healthy person. ZnO-SARS-CoV-2-rS and ZnO-SARS-CoV-2-rN biosensors showed high stability and sensitivity to anti-SARS-CoV-2 antibodies in the range of 0.025-0.5 nM (LOD 0.01 nM) and 0.3-1 nM (LOD 0.3 nM), respectively. Gibbs free energy of interaction between ZnO/SARS-CoV-2-rS and ZnO/SARS-CoV-2-rN bioselective layers with anti-SARS-CoV-2 antibodies showed -35.5 and -21.4 kJ/mol, respectively. Average detection time of biosensor integrated within microfluidic system was 15-20 min. The detection time and pumping speed (50 μL/min) were optimized to make detection faster. The developed system and ZnO-SARS-CoV-2-rS nanostructures have good potential for detection of anti-SARS-CoV-2 antibodies from patient's probes.

Rapid, on-site quantitative determination of mycotoxins in grains using a multiple time-resolved fluorescent microsphere immunochromatographic test strip

The label probe plays a crucial role in enhancing the sensitivity of lateral flow immunoassays. However, conventional fluorescent microspheres (FMs) have limitations due to their short fluorescence lifetime, susceptibility to background fluorescence interference, and inability to facilitate multi-component detection. In this study, carboxylate-modified Eu(III)-chelate-doped polystyrene nanobeads were employed as label probes to construct a multiple time-resolved fluorescent microsphere-based immunochromatographic test strip (TRFM-ICTS). This novel TRFM-ICTS facilitated rapid on-site quantitative detection of three mycotoxins in grains: Aflatoxin B1 (AFB1), Zearalenone (ZEN), and Deoxynivalenol (DON). The limit of detection (LOD) for AFB1, ZEN, and DON were found to be 0.03 ng/g, 0.11 ng/g, and 0.81 ng/g, respectively. Furthermore, the TRFM-ICTS demonstrated a wide detection range for AFB1 (0.05-8.1 ng/g), ZEN (0.125-25 ng/g), and DON (1.0-234 ng/g), while maintaining excellent selectivity. Notably, the test strip exhibited remarkable stability, retaining its detection capability even after storage at 4 °C for over one year. Importantly, the detection of these mycotoxins relied solely on simple manual operations, and with a portable reader, on-site detection could be accomplished within 20 min. This TRFM-ICTS presents a promising solution for sensitive on-site mycotoxin detection, suitable for practical application in various settings due to its sensitivity, accuracy, simplicity, and portability.

Recent Advances of Food Hazard Detection Based on Artificial Nanochannel Sensors

Food quality and safety are related to the health and safety of people, and food hazards are important influencing factors affecting food safety. It is strongly necessary to develop food safety rapid detection technology to ensure food safety. As a new detection technology, artificial nanochannel-based electrochemical and other methods have the advantages of being real-time, simple, and sensitive and are widely used in the detection of food hazards. In this paper, we review artificial nanochannel sensors as a new detection technology in food safety for different types of food hazards: biological hazards (bacteria, toxins, viruses) and chemical hazards (heavy metals, organic pollutants, food additives). At the same time, we critically discuss the advantages and disadvantages of artificial nanochannel sensor detection, as well as the restrictions and solutions of detection, and finally look forward to the challenges and development prospects of food safety detection technology based on the limitations of artificial nanochannel detection. We expect to provide a theoretical basis and inspiration for the development of rapid real-time detection technology for food hazards and the production of portable detection equipment in the future.

1D ZnO-Au nanocomposites as label-free photoluminescence immunosensors for rapid detection of Listeria monocytogenes

In this study, we explore the potential of 1D ZnO-Au nanocomposites as innovative label-free photoluminescence (PL) immunosensors for rapidly detecting Listeria monocytogenes, a significant concern in food safety. We synthesized ZnO nanorods (ZnO_NR) and nanowires (ZnO_NW), followed by Au deposition to create ZnO_NR/Au and ZnO_NW/Au nanocomposites. Our analyses, including SEM, TEM, Raman spectroscopy, and photoluminescence (PL), revealed distinct structural and optical properties of these nanocomposites, especially noting the superior crystallinity and stability of ZnO_NR/Au. The biosensor performance was evaluated through PL sensitivity to Anti-Listeria antibodies, demonstrating that ZnO_NR with higher concentration of Au nanoparticles exhibited higher sensitivity and a lower limit of detection (LOD), attributed to a greater density of Listeria binding sites. The developed biosensor demonstrated a remarkable limit of detection (LOD) of 8.3 × 102 CFU/mL, rivaling or surpassing conventional culture-based methods and some molecular techniques. This research underscores the critical role of Au deposition duration in optimizing biosensor performance and presents a promising advancement in rapid and sensitive Listeria detection, with significant implications for enhancing food safety protocols.

Plasmonic immunosensors based on spoon-shaped waveguides for fast and on-site ultra-low detection of ochratoxin A in coffee samples

The high toxicity and occurrence of ochratoxin A (OTA) in grains and foods has been a growing concern due to the impacts on health and the economy in many countries. In this sense, simplified devices with high sensitivity and specificity for local monitoring are enthusiastically pursued. In this work, we report for the first time the detection of ochratoxin A in coffee samples using a spoon-shaped waveguide immunosensor. The biosensor was built with the surface of the spoon-shaped waveguide covered by a 60 nm layer of gold to enable the SPR phenomenon. The measurements indicated a linear relationship between the change in the SPR phenomenon values and the OTA concentration in the range from 0.2 ppt to 5 ppt. When analyzed in coffee samples, the biosensor was highly selective and did not suffer matrix interference. The developed biosensor represents a promising analytical device for coffee quality analyses, as it is portable, simple, and suitable for onsite detection of target analytes.

Development of magnetic fluorescence aptasensor for sensitive detection of saxitoxin based on Fe3O4@Au-Pt nanozymes

In this work, on the basis of Fe3O4@Au-Pt nanozymes (MAP NZs) and aptamer recognition, a magnetic fluorescent aptasensor (MFA) was developed for sensitive and accurate detection of saxitoxin (STX). With the bridge of STX aptamer (AptSTX) and complementary DNA (cDNA), AptSTX decorated MAP NZs (MAP/Apt) and cDNA modified green quantum dots (cDNA@g-QDs) were connected to form MAP/Apt-cDNA@g-QDs complex. As STX behaves a strong binding ability towards AptSTX, it will compete with cDNA and hybridize with Apt to release cDNA@g-QDs. With the addition of TMB, MAP will catalyze TMB to the oxidized TMB (ox-TMB), thereby quenching the fluorescence of g-QDs due to the inner filter effect. Based on this finding, the quantitative relationship between the change in fluorescence of gQDs and STX concentration was explored with a limit of detection (LOD, S/N = 3) of 0.6 nM. An internal standard signal of oxTMB was adopted and reduced the fluctuation of fluorescence signal output. Besides, the fluorescence probe can selectively recognize and detect STX among five marine toxins. Eventually, the MFA method behaved good performance in detecting seafood samples with recoveries of 82.0 % ∼ 102.6 % as well as coefficient of variations (CV) of 7.2 % ∼ 10.3 %. Therefore, the method with internal signal is hopeful to be a potential candidate for sensitive and accurate detection of STX in seafood.

Comprehensive Insights into Ochratoxin A: Occurrence, Analysis, and Control Strategies

Ochratoxin A (OTA) is a toxic mycotoxin produced by some mold species from genera Penicillium and Aspergillus. OTA has been detected in cereals, cereal-derived products, dried fruits, wine, grape juice, beer, tea, coffee, cocoa, nuts, spices, licorice, processed meat, cheese, and other foods. OTA can induce a wide range of health effects attributable to its toxicological properties, including teratogenicity, immunotoxicity, carcinogenicity, genotoxicity, neurotoxicity, and hepatotoxicity. OTA is not only toxic to humans but also harmful to livestock like cows, goats, and poultry. This is why the European Union and various countries regulate the maximum permitted levels of OTA in foods. This review intends to summarize all the main aspects concerning OTA, starting from the chemical structure and fungi that produce it, its presence in food, its toxicity, and methods of analysis, as well as control strategies, including both fungal development and methods of inactivation of the molecule. Finally, the review provides some ideas for future approaches aimed at reducing the OTA levels in foods.

A novel competitive fluorescence colorimetric dual-mode immunosensor for detecting ochratoxin A based on the synergistically enhanced peroxidase-like activity of AuAg NCs-SPCN nanocomposite

The sensitive and rapid detection of Ochratoxin A in foods is particularly urgent for ensuring human security due to its larger toxicity to the body. Herein, a novel competitive fluorescence colorimetric dual-mode immunosensor for detecting Ochratoxin A based on AuAg NCs-SPCN nanocomposite was designed and constructed. The synergistic effect of SPCN and AuAg NCs dramatically improved the nanozyme activity. The fluorescence intensity was enhanced due to the aggregation luminescence effect, and a new emission peak appeared at 440 nm to form a fluorescence signal. For colorimetric, H2O2 was effectively decomposed by AuAg NCs-SPCN to form ·OH groups and oxidize 3,3',5,5'-tetramethylbenzidine to blue oxTMB. The dual-mode immunosensor showed a good linear relationship from 0.001 μg/L to 10 μg/L and the detection limits were 0.155 ng/L (fluorescence) and 0.213 ng/L (colorimetric). So, this dual-mode immunosensor would have a potential applicative prospect for sensitive detecting Ochratoxin A and other small molecules.

"Three-in-One" Multifunctional Hollow Nanocages with Colorimetric Photothermal Catalytic Activity for Enhancing Sensitivity in Biosensing

Immunochromatographic assays (ICAs) have been widely used in the field detection of mycotoxin contaminants. Nevertheless, the lack of multisignal readout capability and the ability of signaling tags to maintain their biological activity while efficiently loading antibodies remain a great challenge in satisfying diverse testing demands. Herein, we proposed a novel three-in-one multifunctional hollow vanadium nanomicrosphere (high brightness-catalytic-photothermal properties)-mediated triple-readout ICA (VHMS-ICA) for sensitive detection of T-2. As the key to this biosensing strategy, vanadium was used as the catalytic-photothermal characterization center, and natural polyphenols were utilized as the bridging ligands for coupling with the antibody while self-assembling with formaldehyde cross-linking into a hollow nanocage-like structure, which offers the possibility of realizing a three-signal readout strategy and improving the coupling efficiency to the antibody while preserving its biological activity. The constructed sensors showed a detection limit (LOD) of 2 pg/mL for T-2, which was about 345-fold higher than that of conventional gold nanoparticle-based ICA (0.596 ng/mL). As anticipated, the detection range of VHMS-ICA was extended about 8-fold compared with the colorimetric signal alone. Ultimately, the proposed immunosensor performed well in maize and oat samples, with satisfactory recoveries. Owing to the synergistic and complementary interactions between distinct signaling modes, the establishment of multimodal immunosensors with multifunctional tags is an efficient strategy to satisfy diversified detection demands.

MXene-Based Chemo-Sensors and Other Sensing Devices

MXenes have received worldwide attention across various scientific and technological fields since the first report of the synthesis of Ti3C2 nanostructures in 2011. The unique characteristics of MXenes, such as superior mechanical strength and flexibility, liquid-phase processability, tunable surface functionality, high electrical conductivity, and the ability to customize their properties, have led to the widespread development and exploration of their applications in energy storage, electronics, biomedicine, catalysis, and environmental technologies. The significant growth in publications related to MXenes over the past decade highlights the extensive research interest in this material. One area that has a great potential for improvement through the integration of MXenes is sensor design. Strain sensors, temperature sensors, pressure sensors, biosensors (both optical and electrochemical), gas sensors, and environmental pollution sensors targeted at volatile organic compounds (VOCs) could all gain numerous improvements from the inclusion of MXenes. This report delves into the current research landscape, exploring the advancements in MXene-based chemo-sensor technologies and examining potential future applications across diverse sensor types.

ZnO nanostructures: A promising frontier in immunosensor development

This review addresses the design of immunosensors, which employ ZnO nanostructures. Various methods of modifying ZnO nanostructures with antibodies or antigens are discussed, including covalent and non-covalent approaches and cross-linking techniques. Immunosensors based on different properties of ZnO nanomaterials are described and compared. This article provides a comprehensive review of electrochemical immunosensors based on ZnO nanostructures and various detection techniques, including cyclic voltammetry (CV), differential pulse voltammetry (DPV), photoelectrochemical (PEC) detection, electrochemical impedance spectroscopy (EIS), and other electrochemical methods. In addition, this review article examines the application of optical detection techniques, including photoluminescence (PL) and electrochemiluminescence (ECL), in the development of immunosensors based on ZnO nanostructures.

Time-resolved fluorescence microspheres-antibody-penicillin-binding protein assisted construction of immunochromatographic assay for sensitive detection of 22 β-lactams in milk

A sensitive immunochromatographic assay (ICA) using time-resolved fluorescence microspheres (TRFMs) coupled with an indirect-labeling mode was developed for simultaneously determining 22 kinds of β-lactams in milk samples. The TRFMs labeled anti-receptor monoclonal antibodies (mAbs) conjugated to penicillin-binding proteins (PBPs) as ternary TRFMs-mAb-PBPs (TMP) nanoscaffolds provide excellent solubility, brightness, and stability. Thanks to the fact that they not only fully expose the binding sites of PBPs, thereby enhancing the biological affinity of PBPs towards the target, but also generated superb fluorescence signals, the versatile TMP manifested unique possibilities as efficient probes for ICA with remarkable enhancement in sensitivity in β-lactams screening. The results showed that the standard curves of the 22 varying β-lactams displayed linearity in their respective concentration ranges (R2 > 0.98), with the cutoff values of 1-100 ng/mL. The constructed TMP-ICA was successfully applied to the analysis of real milk, with consistent results compared with liquid chromatography-tandem mass spectrometry (LC-MS), providing an effective method for sensing β-lactams in food matrices.

Shaping the Structure and Properties of TiO2-ZnO Oxide Coatings Produced by Plasma Electrolytic Oxidation on Titanium Substrate

The paper presents the results of preliminary research on the possibility of synthesizing ZnO-TiO2 mixed coatings by plasma electrochemical oxidation (PEO). The aim of the work was to synthesize TiO2-ZnO mixed coatings on a titanium substrate from an electrolyte containing ZnO nanoparticles (NPs) and to assess the parameters of PEO on the structure, chemical composition, and properties of the obtained oxide coatings. The PEO process was carried out under various current-voltage conditions using different signals: DC, DC pulse, and AC. In this work, optimal conditions for the PEO process were determined to obtain well-adhering oxide coatings with the highest possible content of ZnO. The structure and morphology of the resulting oxide coatings were investigated, and their chemical and phase composition was comprehensively examined (EDX, XRD, XPS, and GD-OES). In addition, their basic optical properties were assessed. It has been shown that in the PEO DC pulse process, it is possible to obtain oxide coatings characterized by a high degree of structure order, high ZnO content in the oxide coating (3.6 at.%, XPS), and prospective applications for photocatalytic purposes (3.12 eV).

Homogeneous Electrochemical Aptasensor for Sensitive Detection of Zearalenone Using Nanocomposite Probe and Silica Nanochannel Film

Developing rapid and efficient analytical methods is of great importance for food safety Herein, we present a novel homogeneous electrochemical aptasensor for ultrasensitive quantitative determination of zearalenone (ZEN) based on a nanocomposite probe and silica nanochannel film. X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy and UV-Vis characterization techniques confirm that graphene oxide (GO) bears an aromatic conjugated structure, along with hydroxyl and carboxyl groups, facilitating the subsequent adsorption of cationic redox hexa-ammine-ruthenium (III) (Ru(NH3)63+) and anionic ZEN aptamer, to form a Ru(NH3)63+-ZEN aptamer-GO nanocomposite probe in a homogeneous solution. Vertically-ordered mesoporous silica films (VMSF) bearing silanol groups can be simply grown on the solid indium tin oxide (ITO) electrode surface and enable the selective preconcentration of Ru(NH3)63+, eventually leading to signal amplification. Since the detachment of Ru(NH3)63+ from the GO surface by the recognized ZEN aptamer in the presence of ZEN, more free Ru(NH3)63+ is released in solution and produces enhanced redox signals at the VMSF modified ITO electrode, allowing quantitative detection of ZEN. On the basis of the above sensing strategy, the proposed homogeneity, due to the assistance of graphene, as well as of the signal amplification and anti-fouling effects of VMSF, accurate analysis of ZEN can be realized in maize and Chinese chestnut samples.

Microfluidic Biosensor Integrated with Signal Transduction and Enhancement Mechanism for Ultrasensitive Noncompetitive Assay of Multiple Mycotoxins

To achieve high-throughput ultrasensitive detection of mycotoxins in food, a functional DNA-guided transition-state CRISPR/Cas12a microfluidic biosensor (named FTMB) was successfully constructed. The signal transduction CRISPR/Cas12a strategy in FTMB has utilized DNA sequences with a specific recognition function and activators to form trigger switches. Meanwhile, the transition-state CRISPR/Cas12a system was constructed by adjusting the composition ratio of crRNA and activator to achieve a high response for low concentrations of target mycotoxins. On the other hand, the signal enhancement of FTMB has efficiently integrated the signal output of quantum dots (QDs) with the fluorescence enhancement effect of photonic crystals (PCs). The construction of universal QDs for the CRISPR/Cas12a system and PC films matching the photonic bandgap produced a significant signal enhancement by a factor of 45.6. Overall, FTMB exhibited a wide analytic range (10^-5-10¹ ng·mL^-1), low detection of limit (fg·mL^-1), short detection period (∼40 min), high specificity, good precision (coefficients of variation <5%), and satisfactory practical sample analysis capacity (the consistency with HPLC at 88.76%-109.99%). It would provide a new and reliable solution for the rapid detection of multiple small molecules in the fields of clinical diagnosis and food safety.

Label-free electrochemical immunosensor for Ochratoxin a detection in coffee samples

Ochratoxin A (OTA) is a nephrotoxic and carcinogenic mycotoxin frequently found in coffee, which directly impacts human health and the economy of many countries. For this reason, there has been a growing need for simple and sensitive tools for the on-site detection of this mycotoxin. In this study, we developed a label-free impedimetric immunosensor to detect OTA. The biosensor was built on a thin-film gold electrode evaporated on glass substrtes, modified with a self-assembled cysteamine monolayer and anti-OTA antibodies. Atomic force microscopy and Microspectroscopy RAMAN confirmed the successful functionalization of the electrodes. The biosensor performance was evaluated by electrochemical impedance spectroscopy and the measurements indicated a linear relationship between the change in the impedance values and the OTA concentration in the range from 0.5 to 100 ng mL^-1 with a limit of detection of 0.15 ng mL^-1. The biosensor was highly selective and did not suffer matrix interference when analyzed in coffee samples. Furthermore, considering the small sample volumes, the short time required for analysis, and the possibility of miniaturization, the developed biosensor represents a promising analytical device for on-site coffee quality analyses.

Double-Enzyme Active Vanadium Nanospheres-Mediated Ratiometric Multicolor Immunosensors for Sensitive Detection of the T-2 Toxin

Owing to its high throughput, simplicity, and rapidity, enzyme-linked immunosorbent assay (ELISA) has attracted much attention in the field of immunoassays. However, the traditional ELISA usually affords a single signal readout and the labeling ability of the enzyme used is poor, resulting in low accuracy and a limited detection range. Herein, a vanadium nanospheres (VNSs)-mediated competitive ratio nanozymes-linked immunosorbent assay (VNSs-RNLISA) was created for the sensitive detection of the T-2 toxin (T-2). As the key to the biosensor, the VNSs with superoxide dismutase-like and peroxidase-like dual-enzyme mimetic activities were synthesized by a one-step hydrothermal method, which oxidized 1,1-diphenyl-2-picryl-hydrazyl fading and catalyzed 3,3',5,5'-tetramethylbenzidine (TMB) color development. Therefore, T-2 could not only be qualitatively measured with the naked eye but also be quantitatively evaluated by monitoring the ratio of absorbance at 450 and 517 nm wavelengths. Moreover, the characterization of a VNSs-labeled antibody probe showed strong dual-enzymatic activity, excellent stability, and high affinity with T-2 [the affinity constant (k_a) was approximately 1.36 × 10⁸ M^-1], which can significantly improve the detection sensitivity. The limit of detection of VNSs-RNLISA was 0.021 ng/mL, which was approximately 27-fold more sensitive than the single signal nanozymes-linked immunosorbent assay (0.561 ng/mL). Besides, the change in the ratio of absorbance (Δ450/Δ517) decreased linearly in a range of 0.22-13.17 ng/mL, outperforming the detection range of a single-mode nano-enzyme-linked immunosorbent assay using TMB by a factor of 1.6 times. Furthermore, the VNSs-RNLISA was successfully used to identify T-2 in maize and oat samples, with recoveries ranging from 84.216 to 125.371%. Overall, this tactic offered a promising platform for the quick detection of T-2 in food and might broaden the application range of the enzyme-linked immunosorbent assay.

Development of immunoassay based on a specific antibody for sensitive detection of nicosulfuron in environment

Nicosulfuron, one of the most widely used selective herbicides in corn field, can effectively control annual and perennial grass weeds, sedges, and some broadleaf weeds. The residual phytotoxicity of nicosulfuron in soil and water has become increasingly prominent. Therefore, an efficient method for detection of nicosulfuron was critical to ensure the sustainable and healthy development of agriculture and the ecological environment. In this paper, five nicosulfuron haptens which contained carboxyl group or aldehyde groups were designed and synthesized, and an indirect competitive immunoassay was developed for the first time. The assay showed an IC50 of 8.42 ng/mL and had negligible cross reactivities toward other sulfonylurea herbicides. In the spike and recovery studies, the recovery rate from soil samples was 95 %-104 %, and that of wheat roots was 92 %-98 %, which showed a good correlation with LC-MS analysis for nicosulfuron. The immunoassay was then used to quantify nicosulfuron concentration which could cause the obvious phytotoxic symptoms to wheat. Obvious symptoms of nicosulfuron phytotoxicity in wheat root was observed at the concentration of 0.068 ± 0.006 mg/kg (ELISA result) which was consistent with 0.072 ± 0.007 mg/kg obtained by LC-MS. The developed immunoassay method is an effective tool for environment contamination monitoring.

Impact of temperature on optical sensing in biology based on investigation of SARS-CoV-2

In this paper, we present an investigation of the influence of the temperature on the sensing of biological samples. We used biofunctionalized microsphere-based fiber-optic sensor to detect immunoglobulin G attached to the sensor head at temperatures relevant in biological research: 5°C, 25°C, and 55°C. The construction of the sensor allowed us to perform measurements in the small amount of solution. The results of our experiment confirm substantial changes in the measured reflected optical power, indicating the need to control the temperature during such measurements. The sensitivity of the sensor used in this research is 8.82 nW/°C. Coefficient R was also calculated and it equals 0.998, which shows good fit between theoretical linear fit and obtained measured data.

Influence of TiO2 and ZnO Nanoparticles on α-Synuclein and β-Amyloid Aggregation and Formation of Protein Fibrils

The most common neurological disorders, i.e., Parkinson's disease (PD) and Alzheimer's disease (AD), are characterized by degeneration of cognitive functions due to the loss of neurons in the central nervous system. The aggregation of amyloid proteins is an important pathological feature of neurological disorders.The aggregation process involves a series of complex structural transitions from monomeric to the formation of fibrils. Despite its potential importance in understanding the pathobiology of PD and AD diseases, the details of the aggregation process are still unclear. Nanoparticles (NPs) absorbed by the human circulatory system can interact with amyloid proteins in the human brain and cause PD. In this work, we report the study of the interaction between TiO₂ nanoparticles (TiO₂-NPs) and ZnO nanoparticles (ZnO-NPs) on the aggregation kinetics of β-amyloid fragment 1-40 (βA) and α-synuclein protein using surface-enhanced Raman spectroscopy (SERS) and tip-enhanced Raman spectroscopy (TERS). The characterizations of ZnO-NPs and TiO₂-NPs were evaluated by X-ray diffraction (XRD) spectrum, atomic force microscopy (AFM), and UV-Vis spectroscopy. The interaction of nanoparticles with amyloid proteins was investigated by SERS. Our study showed that exposure of amyloid protein molecules to TiO₂-NPs and ZnO-NPs after incubation at 37 °C caused morphological changes and stimulated aggregation and fibrillation. In addition, significant differences in the intensity and location of active Raman frequencies in the amide I domain were found. The principal component analysis (PCA) results show that the effect of NPs after incubation at 4 °C does not cause changes in βA structure.

Ochratoxin A as alarming health in livestock and human: A review on molecular interactions, mechanism of toxicity, detection, detoxification, and dietary prophylaxis

Ochratoxin A (OTA) is a toxic metabolite produced by Aspergillus and Penicillium fungi commonly found in raw plant sources and other feeds. This review comprises an extensive evaluation of the origin and proprieties of OTA, toxicokinetics, biotransformation, and toxicodynamics of ochratoxins. In in vitro and in vivo studies, the compatibility of OTA with oxidative stress is observed through the production of free radicals, resulting in genotoxicity and carcinogenicity. The OTA leads to nephrotoxicity as the chief target organ is the kidney. Other OTA excretion and absorption rates are observed, and the routes of elimination include faeces, urine, and breast milk. The alternations in the Phe moiety of OTA are the precursor for the amino acid alternation, bringing about Phe-hydroxylase and Phe-tRNA synthase, resulting in the complete dysfunction of cellular metabolism. Biodetoxification using specific microorganisms decreased the DNA damage, lipid peroxidation, and cytotoxicity. This review addressed the ability of antioxidants and the dietary components as prophylactic measures to encounter toxicity and demonstrated their capability to counteract the chronic exposure through supplementation as feed additives.

Dual-Modal Immunochromatographic Test for Sensitive Detection of Zearalenone in Food Samples Based On Biosynthetic Staphylococcus aureus-Mediated Polymer Dot Nanocomposites

The rapid detection of toxins is of great significance to food security and human health. In this work, a dual-modality immunochromatographic test (DICT) mediated by Staphylococcus aureus (SA)-biosynthesized polymer dots (SABPDs) was constructed for sensitive monitoring of zearalenone (ZEN) in agro products. The SABPDs as potent microorganism nanoscaffolds with excellent solubility, brightness, and stability were ingeniously fabricated employing hydroquinone and SA as precursors in the Schiff base reaction and a self-assembly technique. Thanks to the fact that they not only preserved an intact microsphere for loading Fc regions of monoclonal antibodies (mAbs) and the affinity of their labeled mAbs to antigen but also generated superb colorimetric-fluorescent dual signals, the versatile SABPDs manifested unique possibilities as the new carriers for dual-readout ICT with remarkable enhancement in sensitivity in ZEN screening (limit of detection = 0.036 ng/mL, which was 31-fold lower than that of traditional gold nanoparticle-based ICT). Ultimately, the proposed immunosensor performed well in millet and corn samples with satisfactory recoveries, demonstrating its potential for point-of-care testing. This work offers a bio-friendly strategy for biosynthesizing cell-based PD vehicles with bimodal signals for food safety analysis.

Toehold-Mediated Cascade Catalytic Assembly for Mycotoxin Detection and Its Logic Applications

In this work, an enzyme-free biosensor is reported for mycotoxin detection based on a toehold-mediated catalytic hairpin assembly (CHA) and a DNAzyme-cascaded hydrolysis reaction. In the presence of a mycotoxin, the recognition between an aptamer and the mycotoxin releases the trigger DNA. The trigger DNA initiates the toehold-mediated CHA, generating large amounts of partial duplex B/C with four toeholds, which can be used to assemble the DNAzyme-cascaded hydrolysis reaction. Furthermore, through a collaborative autoassembly reaction among the B/C duplex, DNA1, and DNA2, supramolecular nanostructures corresponding to Mg²⁺-dependent DNAzymes can be formed. With the incubation of Mg²⁺, the dual-modified (TAMRA/BHQ2) substrate strand DNA2 will be cleaved into two fragments, yielding a high TAMRA fluorescence signal for mycotoxin testing. Under optimal conditions, the sensing system was ultrasensitive and showed low detection limits of 0.2 pM for ochratoxin A (OTA), 0.13 pM for aflatoxin B1 (AFB1), and 0.17 pM for zearalenone (ZEN). The mycotoxin aptasensor also exhibited high selectivity and was successfully applied for the quantitative analysis of OTA, AFB1, and ZEN in wine samples. Due to the advantages of flexibility and versatility, this mycotoxin platform was used to fabricate several concatenated logic gates including "AND-INHIBIT", "INHIBIT-OR", "OR-AND", and "OR-INHIBIT" logic biocomputings. Such multiple functions of the logic system provided a universal sensing strategy for the intelligent detection of multiplex mycotoxins, demonstrating considerable potential in food safety and environmental monitoring.

ZnO Transducers for Photoluminescence-Based Biosensors: A Review

Zinc oxide (ZnO) is a wide bandgap semiconductor material that has been widely explored for countless applications, including in biosensing. Among its interesting properties, its remarkable photoluminescence (PL), which typically exhibits an intense signal at room temperature (RT), arises as an extremely appealing alternative transduction approach due to the high sensitivity of its surface properties, providing high sensitivity and selectivity to the sensors relying on luminescence output. Therefore, even though not widely explored, in recent years some studies have been devoted to the use of the PL features of ZnO as an optical transducer for detection and quantification of specific analytes. Hence, in the present paper, we revised the works that have been published in the last few years concerning the use of ZnO nanostructures as the transducer element in different types of PL-based biosensors, namely enzymatic and immunosensors, towards the detection of analytes relevant for health and environment, like antibiotics, glucose, bacteria, virus or even tumor biomarkers. A comprehensive discussion on the possible physical mechanisms that rule the optical sensing response is also provided, as well as a warning regarding the effect that the buffer solution may play on the sensing experiments, as it was seen that the use of phosphate-containing solutions significantly affects the stability of the ZnO nanostructures, which may conduct to misleading interpretations of the sensing results and unreliable conclusions.

Biosensors for the Determination of SARS-CoV-2 Virus and Diagnosis of COVID-19 Infection

Monitoring and tracking infection is required in order to reduce the spread of the coronavirus disease 2019 (COVID-19), induced by severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). To achieve this goal, the development and deployment of quick, accurate, and sensitive diagnostic methods are necessary. The determination of the SARS-CoV-2 virus is performed by biosensing devices, which vary according to detection methods and the biomarkers which are inducing/providing an analytical signal. RNA hybridisation, antigen-antibody affinity interaction, and a variety of other biological reactions are commonly used to generate analytical signals that can be precisely detected using electrochemical, electrochemiluminescence, optical, and other methodologies and transducers. Electrochemical biosensors, in particular, correspond to the current trend of bioanalytical process acceleration and simplification. Immunosensors are based on the determination of antigen-antibody interaction, which on some occasions can be determined in a label-free mode with sufficient sensitivity.

Dual-heteroatom-templated lanthanoid-inserted heteropolyoxotungstates simultaneously comprising Dawson and Keggin subunits and their composite film applied for electrochemical immunosensing of auximone

Two unprecedented PIII–SbIII-heteroatom templated lanthanide-inserted heteropolyoxotungstates were obtained and their composite film was applied for the electrochemical immunosensing of auximone.

Self-assembled recombinant camel serum albumin nanoparticles-encapsulated hemin with peroxidase-like activity for colorimetric detection of hydrogen peroxide and glucose

The construction of enzyme mimics using protein protection layers possesses advantages of high biocompatibility and superior catalytic activity, which is desirable for biomedical applications including diseases diagnosis. Here, from E. coli expression system, recombinant protein of camel serum albumin (rCSA) from Camelus bactrianus was successfully obtained to encapsulate hemin via the self-assemble method without additional toxic organic reagents. As compared with that of horseradish peroxidase, the produced rCSA-hemin nanoparticles exhibited enhanced enzyme-mimicking activity and stability under harsh experimental conditions. Additionally, the steady-state kinetic analysis of rCSA-hemin in the solution revealed its higher affinity to the substrates. Therefore, a colorimetric detection method of H₂O₂ and glucose was constructed with a linear range of 2.5-500 μM with an LOD of 2.39 and 2.42 μM, respectively, which was also applied for the determination of glucose in the serum samples with satisfying recovery ratio ranging from 101.1% to 112.1%. The constructed camel protein-derived nanozyme system of remarkable stability holds promising potentials for the versatile biomedical uses.

Advances and insights in the diagnosis of viral infections

Viral infections are the most common among diseases that globally require around 60 percent of medical care. However, in the heat of the pandemic, there was a lack of medical equipment and inpatient facilities to provide all patients with viral infections. The detection of viral infections is possible in three general ways such as (i) direct virus detection, which is performed immediately 1-3 days after the infection, (ii) determination of antibodies against some virus proteins mainly observed during/after virus incubation period, (iii) detection of virus-induced disease when specific tissue changes in the organism. This review surveys some global pandemics from 1889 to 2020, virus types, which induced these pandemics, and symptoms of some viral diseases. Non-analytical methods such as radiology and microscopy also are overviewed. This review overlooks molecular analysis methods such as nucleic acid amplification, antibody-antigen complex determination, CRISPR-Cas system-based viral genome determination methods. Methods widely used in the certificated diagnostic laboratory for SARS-CoV-2, Influenza A, B, C, HIV, and other viruses during a viral pandemic are outlined. A comprehensive overview of molecular analytical methods has shown that the assay's sensitivity, accuracy, and suitability for virus detection depends on the choice of the number of regions in the viral open reading frame (ORF) genome sequence and the validity of the selected analytical method.

Immunosensing Based on Optical Fiber Technology: Recent Advances

The evolution of optical fiber technology has revolutionized a variety of fields, from optical transmission to environmental monitoring and biomedicine, given their unique properties and versatility. For biosensing purposes, the light guided in the fiber core is exposed to the surrounding media where the analytes of interest are detected by different techniques, according to the optical fiber configuration and biofunctionalization strategy employed. These configurations differ in manufacturing complexity, cost and overall performance. The biofunctionalization strategies can be carried out directly on bare fibers or on coated fibers. The former relies on interactions between the evanescent wave (EW) of the fiber and the analyte of interest, whereas the latter can comprise plasmonic methods such as surface plasmon resonance (SPR) and localized SPR (LSPR), both originating from the interaction between light and metal surface electrons. This review presents the basics of optical fiber immunosensors for a broad audience as well as the more recent research trends on the topic. Several optical fiber configurations used for biosensing applications are highlighted, namely uncladded, U-shape, D-shape, tapered, end-face reflected, fiber gratings and special optical fibers, alongside practical application examples. Furthermore, EW, SPR, LSPR and biofunctionalization strategies, as well as the most recent advances and applications of immunosensors, are also covered. Finally, the main challenges and an outlook over the future direction of the field is presented.

Electrochemical and photoluminescence response of laser-induced graphene/electrodeposited ZnO composites

The inherent scalability, low production cost and mechanical flexibility of laser-induced graphene (LIG) combined with its high electrical conductivity, hierarchical porosity and large surface area are appealing characteristics for many applications. Still, other materials can be combined with LIG to provide added functionalities and enhanced performance. This work exploits the most adequate electrodeposition parameters to produce LIG/ZnO nanocomposites. Low-temperature pulsed electrodeposition allowed the conformal and controlled deposition of ZnO rods deep inside the LIG pores whilst maintaining its inherent porosity, which constitute fundamental advances regarding other methods for LIG/ZnO composite production. Compared to bare LIG, the composites more than doubled electrode capacitance up to 1.41 mF cm-2 in 1 M KCl, while maintaining long-term cycle stability, low ohmic losses and swift electron transfer. The composites also display a luminescence band peaked at the orange/red spectral region, with the main excitation maxima at ~ 3.33 eV matching the expected for the ZnO bandgap at room temperature. A pronounced sub-bandgap tail of states with an onset absorption near 3.07 eV indicates a high amount of defect states, namely surface-related defects. This work shows that these environmentally sustainable multifunctional nanocomposites are valid alternatives for supercapacitors, electrochemical/optical biosensors and photocatalytic/photoelectrochemical devices.

Development of a functional impedimetric immunosensor for accurate detection of thyroid-stimulating hormone

Thyroid-stimulating hormone (TSH), which regulates the synthesis of thyroid gland hormones affecting the whole metabolism, is a pituitary hormone. Determination of TSH is crucial for monitoring thyroid gland-related disorders and some metabolic diseases.In this study, a nonlabeled immunosensor based on covalent immobilization of anti-TSH antibody by using the formation of self-assembled monolayers (SAM) of 4-mercaptophenylacetic acid (4-MPA) and functionalization of carboxyl ends with 1-ethyl-3-(3-dimetilaminopropil) carbodiimide (EDC)/N-Hydroxysuccinimide (NHS) was fabricated for detection of TSH. Immobilization steps including the concentration of 4-MPA, the concentration of anti-TSH antibody, and duration of anti-TSH antibody incubation were optimized by utilizing electrochemical impedance spectroscopy. Under optimal conditions, a sensitive, rapid, and accurate determination of TSH at a concentration range between 0.7 and 3.5 mIU/L was accomplished with a notable linearity and LOD value of 0.034 mIU/L, as well as reproducibility and repeatability. Moreover, for comparison, linear range experiments were also carried out by using other electrochemical methods, including linear sweep voltammetry, cyclic voltammetry, and capacitance spectroscopy. Finally, the constructed immunosensor was used for analyzing TSH levels spiked in the artificial serum samples.

Affinity Sensors for the Diagnosis of COVID-19

The coronavirus disease 2019 (COVID-19) outbreak caused by severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) was proclaimed a global pandemic in March 2020. Reducing the dissemination rate, in particular by tracking the infected people and their contacts, is the main instrument against infection spreading. Therefore, the creation and implementation of fast, reliable and responsive methods suitable for the diagnosis of COVID-19 are required. These needs can be fulfilled using affinity sensors, which differ in applied detection methods and markers that are generating analytical signals. Recently, nucleic acid hybridization, antigen-antibody interaction, and change of reactive oxygen species (ROS) level are mostly used for the generation of analytical signals, which can be accurately measured by electrochemical, optical, surface plasmon resonance, field-effect transistors, and some other methods and transducers. Electrochemical biosensors are the most consistent with the general trend towards, acceleration, and simplification of the bioanalytical process. These biosensors mostly are based on the determination of antigen-antibody interaction and are robust, sensitive, accurate, and sometimes enable label-free detection of an analyte. Along with the specification of biosensors, we also provide a brief overview of generally used testing techniques, and the description of the structure, life cycle and immune host response to SARS-CoV-2, and some deeper details of analytical signal detection principles.

Well-orientation strategy for direct binding of antibodies: Development of the immunochromatographic test using the antigen modified Fe2O3 nanoprobes for sensitive detection of aflatoxin B1

One of the major concerns in the application of nanocarriers in biosensing is the impair of the recognition molecules bioactivity loaded on their surfaces due to harsh and laborious cross-linking and random orientation, resulting in unsatisfactory sensitivity. Herein, we proposed a novel immunochromatographic test strip (FNS-ag-DICTS) by taking advantage of the antigen (ag) modified Fe₂O₃ nanostructures (FNSs) as new signal tags and goat anti-mouse IgG labeling on the detection line instead of ag, which was used for sensitive detection of aflatoxin B₁ (AFB₁). The fabricated FNS-ag can orientate the Fab region of monoclonal antibodies (mAbs), waiving the intrinsic limitations of traditional nanomaterials labeled mAbs. Under optimal conditions, FNS-ag-DICTS possessed excellent specificity and a wide detection range, with a visual limit of detection (vLOD) of 0.0125 ng mL^-1. In addition, the biosensor successfully detected AFB₁ in peanut, green bean and corn, with an average recovery rate of 82.8-124.9%.

Formation and Photoluminescence Properties of ZnO Nanoparticles on Electrospun Nanofibers Produced by Atomic Layer Deposition

The unique combination of optical, chemical, and structural properties of one-dimensional zinc oxide (1D ZnO) makes it one of the most attractive materials in a wide range of research and applications. In the present study, 1D ZnO nanomaterials were fabricated using a combination of two independent methods: electrospinning and atomic layer deposition (ALD). The electrospinning technique was used to produce 1D electrospun fibers consisting of four types of polymers: polylactic acid (PLLA), polyvinylidene fluoride (PVDF), polyvinyl alcohol (PVA), and polyamide 6 (PA6). The ALD technology, in turn, was selected as an excellent candidate for the synthesis of a ZnO thin layer over polymer fibers for the production of 1D ZnO/polymer nanofiber composites (PLLA/ZnO, PVDF/ZnO, PVA/ZnO, PA6/ZnO). Structural and optical properties of the produced nanofibers were studied by means of scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), diffuse reflectance, and photoluminescence (PL) spectroscopy. It was found that only PVDF/ZnO nanofibers exhibit stable room temperature PL that may be the result of a higher ZnO content in the sample. In addition, PL measurements were conducted as a function of excitation power and temperature in order to establish the main PL mechanisms and parameters for the PVDF/ZnO sample, as a most promising candidate for the biophotonic application.

Influence of PDA Coating on the Structural, Optical and Surface Properties of ZnO Nanostructures

Polydopamine (PDA) is a new biocompatible material, which has prospects in biomedical and sensor applications. Due to functional groups, it can host wide range of biomolecules. ZnO nanostructures are well known templates for optical sensors and biosensors. The combination of ZnO and PDA results in a change of optical properties of ZnO-PDA composites as a shift of photoluminescence (PL) peaks and PL quenching. However, to date, the effect of the PDA layer on fundamental properties of ZnO-PDA nanostructures has not been studied. The presented paper reports on optical and surface properties of novel ZnO-PDA nanocomposites. PDA layers were chemically synthesized on ZnO nanostructures from different solution concentrations of 0.3, 0.4, 0.5 and 0.7 mg/mL. Structure, electronic and optical properties were studied by SEM, Raman, FTIR, diffuse reflectance and photoluminescence methods. The Z-potential of the samples was evaluated in neutral pH (pH = 7.2). The response of the samples towards poly-l-lysine adsorption, as a model molecule, was studied by PL spectroscopy to evaluate the correlation between optical and surface properties. The role of the PDA concentration on fundamental properties was discussed.

Molecularly imprinted photoelectrochemical sensing based on ZnO/polypyrrole nanocomposites for acrylamide detection

A highly sensitive quenching molecular imprinting (MIP) photoelectrochemical (PEC) sensor was proposed to detect acrylamide (AM) by using the photoactive composite of ZnO and polypyrrole (PPy) as the PEC signal probe. ZnO, with high electron mobility, excellent chemical and thermal stability as well as good biocompatibility, was selected as the photoelectrically active material. A polypyrrole film was formed on the nanodisk ZnO by electrochemical polymerization, and the recognition site of AM was left on the surface of the PPy film by elution, enabling the specific detection of AM. The transfer of electrons will be hindered when AM is adsorbed on the ZnO/PPy nanocomposites surface, which results in the decrease of photocurrent signal. The proposed molecularly imprinted PEC sensor exhibits significant detection performance of AM in the range of 10-1 M-2.5 × 10-9 M with a LOD of 2.147 × 10-9 M (S/N = 3). The use of photoelectrochemical technology combined with molecular imprinting technology enables the PEC sensor to have excellent selectivity, superior repeatability, preferable stability, low cost, and easy construction, providing a new method for the detection of AM. The high recovery rate in the detection of real samples of potato chips and biscuits indicates that the proposed PEC sensor has potential in monitoring the emerging food safety risks.

Advances in immunosensor technology

In recent years, advances in immunosensor device fabrication have significantly expanded the use of this technology in a broad range of applications including clinical diagnosis, food analysis, quality control, environmental studies and industrial monitoring. The most important aspect in fabrication is to obtain a design that provides a low detection limit. The utilization of nanomaterials as a label, catalyst and biosensing transducer is, perhaps, the most popular approach in ultrasensitive devices. This chapter reviews recent advances in immunosensor fabrication and summarizes the most recent studies. Strategies employed to significantly improve sensitivity and specificity of immunosensor technology and the advantages and limitations thereof are explored.

Photoluminescence label-free immunosensor for the detection of Aflatoxin B1 using polyacrylonitrile/zinc oxide nanofibers

The precise and rapid detection of hazardous molecules, microorganisms, pollutants, and toxins currently remains a global challenge. Aflatoxin B1 (AFB1) is a toxic and dangerous product of fungi that considered as cancerogenic, mutagenic, and immunosuppressive for humans and animals. Therefore, the screening of AFB1 in food and beverages plays an important role in preventing foodborne illnesses. In this study, AFB1 molecules were detected in a microfluidic device with integrated polyacrylonitrile/zinc oxide (PAN/ZnO) nanofibers fabricated via a combination of the electrospinning, and atomic layer deposition (ALD) techniques. The structural and optical analyses of PAN/ZnO nanofibers were performed and samples with the most suitable properties were utilized for AFB1 detection. In order to obtain the biorecognition layer towards AFB1, PAN/ZnO samples were modified by (3-Aminopropyl) triethoxysilane (APTES), and glutaraldehyde (GA), bovine serum albumin (BSA) and monoclonal antibodies (Anti-AFB1). Subsequently, photoluminescence (PL)-based immunosensor was integrated into a microfluidic cell and tested for AFB1 detection. The mechanism of PL changes caused by AFB1 & Anti-AFB1 complex formation was analyzed and developed. The proposed approach enables the detection of AFB1 with the lowest concentration (LOD) of about 39 pg/ml, while the sensitivity range was evaluated as 0.1-20 ng/ml. The obtained values of LOD and sensitivity, as well as the simplicity of the detection method, make this approach a prospect for further application.

Synthesis and photoluminescence properties of hybrid 1D core-shell structured nanocomposites based on ZnO/polydopamine

In the present work, we report on the modelling of processes at the zinc oxide and polydopamine (ZnO/PDA) interface. The PDA layer was deposited onto ZnO nanorods (NRs) via chemical bath deposition. The defect concentrations in ZnO before and after PDA deposition were calculated and analysed. The ZnONRs/PDA core–shell nanostructures were studied by transmission electron microscopy (TEM), X-ray diffraction (XRD), Raman and Fourier-transform infrared (FTIR) spectroscopy, photoluminescence (PL) measurements, and diffuse reflectance spectroscopy. The TEM and electron energy loss spectroscopy (EELS) measurements confirmed the conformal coating of PDA, while the PL emission from ZnO and ZnONRs/PDA samples showed a reduction of intensity after the PDA deposition. The decrease of defect concentration participating in PL and quantum efficiency explains the PL reduction. Finally, the observed decrease of activation energies and a shift of the PL peaks are attributed to the formation of an additional local electrical field between the PDA and ZnO nanostructures.

The results shown in this study provide a unique insight into the optical and electronic processes of the ZnO/PDA interface.

Multifunctional Fe3O4@Au supraparticle as a promising thermal contrast for an ultrasensitive lateral flow immunoassay

An ultrasensitive lateral flow immunoassay (LFIA) strip has been developed based on a multifunctional photothermal contrast Fe₃O₄@Au supraparticle (Fe₃O₄@Au SP) for quantitative Ochratoxin A (OTA) detection. The Fe₃O₄@Au SP composite not only shows a better photothermal effect over Fe₃O₄ and gold nanoparticles, but possesses magnetic property and excellent ability to directly adsorb protein (antibody). Under 808 nm irradiation, photothermal images of the test strips are recorded by a portable Infrared thermal camera. A quantitative analysis is easily achieved based on the thermal changes, which are proportional to the concentrations of analytes. Under an optimal condition, a wide linear detection range from 1 pg mL⁻¹ to 1μgmL⁻¹ and a limit of detection (LOD) at 0.12 pg mL⁻¹ have been achieved with OTA as a model analytes. The practical application potential has also been validated by detection of OTA in spiked corn, peanut, and soybean extractives with overall recoveries ranging from 98.6% to 115% and coefficient of variations (CVs) between 6.06% and 12.73%. The photothermal LFIA renders a rapid, sensitive, and quantitative bio-/chemo-sensing platform with only a portable laser source and a thermal camera.

Ultrasensitive detection of ochratoxin A based on biomimetic nanochannel and catalytic hairpin assembly signal amplification

In this paper, an ultrasensitive nanochannel sensor has been proposed for label-free Ochratoxin A (OTA) assay in combination with graphene oxide (GO) and catalyzed hairpin assembly (CHA). The high-performance sensor is segmented into two parts. One is composed of graphene oxide (GO) and DNA probes. In the presence of target OTA, OTA works as a catalyst to trigger the self-assembly pathway of the two probes and initiate the cycling of CHA circuits, which results in numerous double-stranded DNAs (dsDNA) in solution. The excess ssDNA probes are removed by GO. The other part is composed of biomimetic nanochannel coated with polyethyleneimine (PEI) and Zr⁴⁺, which can quantify the concentration of OTA by detecting the dsDNA in solution. The nanofluidic device has a detection limit of as low as 6.2 pM with an excellent selectivity. The nanochannel based assay was used to analyse food samples (red wine) with satisfied results. Thus, the proposed analytical method will provide a new approach the detection of OTA and can be applied for quality control to ensure food safety.

Evaluation of electrochemical quartz crystal microbalance based sensor modified by uric acid-imprinted polypyrrole

Uric acid-imprinted polypyrrole-based (MIP_(UA)-Ppy) electrochemical quartz crystal microbalance sensor (EQCM) was developed. Experiments and theoretical calculations were focused on molecular interactions between uric acid molecule and: i) polypyrrole imprinted by uric acid (MIP_(UA)-Ppy) ii) polypyrrole film without any molecular imprints (NIP-Ppy). Resonant frequency differences during electrochemical deposition of MIP_(UA)-Ppy and NIP-Ppy films were observed and were attributed to the phenomenon of molecule capture within formed Ppy matrix. EQCM-resonators modified by MIP-Ppy showed the following advantages: selectivity, qualitative response, cost-effectiveness, and simple procedure. The selectivity of MIP_(UA)-Ppy was tested by the replacement of uric acid in the PBS solution with several different concentrations of caffeine and glucose. Langmuir isotherm based molecular adsorption model was applied to evaluate the interaction of MIP_(UA)-Ppy with uric acid. From experimental results calculated the standard Gibbs free energy of association (ΔG_a) of uric acid with MIP_(UA)-Ppy is -16.4 ± 2.05 kJ/mol and with NIP-Ppy is -13.3 ± 8.56 kJ/mol ΔG values illustrate that the formation of uric acid complex with MIP_(UA)-Ppy is thermodynamically more favourable than that for complexation with NIP-Ppy.

Photoluminescent Detection of Human T-Lymphoblastic Cells by ZnO Nanorods

The precise detection of cancer cells currently remains a global challenge. One-dimensional (1D) semiconductor nanostructures (e.g., ZnO nanorods) have attracted attention due to their potential use in cancer biosensors. In the current study, it was demonstrated that the possibility of a photoluminescent detection of human leukemic T-cells by using a zinc oxide nanorods (ZnO NRs) platform. Monoclonal antibodies (MABs) anti-CD5 against a cluster of differentiation (CD) proteins on the pathologic cell surface have been used as a bioselective layer on the ZnO surface. The optimal concentration of the protein anti-CD5 to form an effective bioselective layer on the ZnO NRs surface was selected. The novel biosensing platforms based on glass/ZnO NRs/anti-CD5 were tested towards the human T-lymphoblast cell line MOLT-4 derived from patients with acute lymphoblastic leukemia. The control tests towards MOLT-4 cells were performed by using the glass/ZnO NRs/anti-IgG2a system as a negative control. It was shown that the photoluminescence signal of the glass/ZnO NRs/anti-CD5 system increased after adsorption of T-lymphoblast MOLT-4 cells on the biosensor surface. The increase in the ZnO NRs photoluminescence intensity correlated with the number of CD5-positive MOLT-4 cells in the investigated population (controlled by using flow cytometry). Perspectives of the developed ZnO platforms as an efficient cancer cell biosensor were discussed.

Porous Silicon-Zinc Oxide Nanocomposites Prepared by Atomic Layer Deposition for Biophotonic Applications

In the current research, a porous silicon/zinc oxide (PSi/ZnO) nanocomposite produced by a combination of metal-assisted chemical etching (MACE) and atomic layer deposition (ALD) methods is presented. The applicability of the composite for biophotonics (optical biosensing) was investigated. To characterize the structural and optical properties of the produced PSi/ZnO nanocomposites, several studies were performed: scanning and transmission electron microscopy (SEM/TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), diffuse reflectance, and photoluminescence (PL). It was found that the ALD ZnO layer fully covers the PSi, and it possesses a polycrystalline wurtzite structure. The effect of the number of ALD cycles and the type of Si doping on the optical properties of nanocomposites was determined. PL measurements showed a “shoulder-shape” emission in the visible range. The mechanisms of the observed PL were discussed. It was demonstrated that the improved PL performance of the PSi/ZnO nanocomposites could be used for implementation in optical biosensor applications. Furthermore, the produced PSi/ZnO nanocomposite was tested for optical/PL biosensing towards mycotoxins (Aflatoxin B1) detection, confirming the applicability of the nanocomposites.

Application of Organic-Inorganic Hybrids in Chemical Analysis, Bio- and Environmental Monitoring

Organic-inorganic hybrids (OIH) are considered to be a powerful platform for applications in many research and industrial fields. This review highlights the application of OIH for chemical analysis, biosensors, and environmental monitoring. A methodology toward metrological traceability measurement and standardization of OIH and demonstration of the role of mathematical modeling in biosensor design are also presented. The importance of the development of novel types of OIH for biosensing applications is highlighted. Finally, current trends in nanometrology and nanobiosensors are presented.

A Fluorescent DNA Hydrogel Aptasensor Based on the Self-Assembly of Rolling Circle Amplification Products for Sensitive Detection of Ochratoxin A

A sensitive fluorescent DNA hydrogel aptasensor based on the self-assembly of rolling circle amplification (RCA) products was developed for ochratoxin A (OTA) detection in beer. A competitive binding mode of aptamer, complementary sequence, and target was integrated into the DNA hydrogel for OTA detection. The OTA aptamer first combined with the primer to form the hybridized product. Then, in the presence of OTA, the aptamer combined with OTA, which released the primer. The released primer hybridized with the padlock probe to form a circular template, and the RCA reaction was initiated by adding ligase, polymerase, and dNTPs. The fluorescent DNA hydrogel was obtained by adding Cy3-dUTP together with dNTPs, and the fluorescence (FL) intensity of the DNA hydrogel was positively correlated with OTA concentration. Under the optimal experimental conditions, the linear range of the relationship varied from 0.05 ng/mL to 100 ng/mL with a detection limit for OTA of 0.01 ng/mL. The fluorescent DNA hydrogel aptasensor showed good specificity and stability in beer samples. Therefore, the fabricated DNA hydrogel aptasensor shows considerable potential applications in detecting OTA for food safety.