Recent advances in carbon nanomaterial-based adsorbents for water purification

Bio-derived carbon-based materials for sustainable environmental remediation and wastewater treatment

Biosynthesized nanocomposites, particularly those incorporating carbon-based materials, exhibit exceptional tunability and multifunctionality, surpassing the capabilities of conventional materials in these aspects. Developing practical solutions is critical to address environmental toxins from pharmaceuticals, heavy metals, pesticides, and dyes. Biomass waste is a readily available carbon source, which emerges as a promising material for producing biochar due to its inherent advantages: abundance, low cost, and environmentally friendly nature. This distribution mainly uses carbon-based materials (CBMs) and biomass waste in wastewater treatment. This review paper investigates several CBM types, including carbon aerogels, nanotubes, graphene, and activated carbon. The development of bio-derived carbon-based nanomaterials are discussed, along with the properties and composition of carbon materials derived from biomass waste and various cycles, such as photodegradation, adsorption, and high-level oxidation processes for natural remediation. In conclusion, this review examines the challenges associated with biochar utilization, including cost, recovery, and practical implementation.

Non-Invasive Detection of Early-Stage Fatty Liver Disease via an On-Skin Impedance Sensor and Attention-Based Deep Learning

Early-stage nonalcoholic fatty liver disease (NAFLD) is a silent condition, with most cases going undiagnosed, potentially progressing to liver cirrhosis and cancer. A non-invasive and cost-effective detection method for early-stage NAFLD detection is a public health priority but challenging. In this study, an adhesive, soft on-skin sensor with low electrode-skin contact impedance for early-stage NAFLD detection is fabricated. A method is developed to synthesize platinum nanoparticles and reduced graphene quantum dots onto the on-skin sensor to reduce electrode-skin contact impedance by increasing double-layer capacitance, thereby enhancing detection accuracy. Furthermore, an attention-based deep learning algorithm is introduced to differentiate impedance signals associated with early-stage NAFLD in high-fat-diet-fed low-density lipoprotein receptor knockout (Ldlr-/-) mice compared to healthy controls. The integration of an adhesive, soft on-skin sensor with low electrode-skin contact impedance and the attention-based deep learning algorithm significantly enhances the detection accuracy for early-stage NAFLD, achieving a rate above 97.5% with an area under the receiver operating characteristic curve (AUC) of 1.0. The findings present a non-invasive approach for early-stage NAFLD detection and display a strategy for improved early detection through on-skin electronics and deep learning.

Mechanisms and extended kinetic model of thermal desorption in organic-contaminated soil

Thermal desorption is a preferred technology for site remediation due to its various advantages. To ensure the effective removal of different pollutants in practical applications, it is necessary to understand the kinetic behaviors and removal mechanisms of pollutants in thermal desorption process. This paper explored the thermal desorption processes of five organic pollutants (nitrobenzene, naphthalene, n-dodecane, 1-nitronaphthalene, and phenanthrene) at 50-350 °C in two different subsoils with 6-18% moisture content. The results suggested that the thermal desorption process was well-fitted by the exponential decay model (R2 = 0.972-0.999) and could be divided into two distinct stages. The first stage was relatively fast and highly influenced by soil moisture, while the second stage showed a slower desorption rate due to the constraints imposed by the soil texture and structure. The influence of soil moisture on thermal desorption depended on the octanol/water partition coefficient (KOW) of pollutants. Pollutants with log KOW values lower than the critical value exhibited enhanced thermal desorption, while those with log KOW values higher than the critical value were inhibited. The critical value of log KOW might be between 3.33 and 4.46. Changes in soil texture and structure caused by heating promoted thermal desorption, especially for naphthalene, 1-nitronaphthalene and phenanthrene. The differences in texture and structure between the two soils diminished as the temperature increased. Finally, an extended kinetic model under changing temperature conditions was derived, and the simulation results for the two subsoils were very close to the actual thermogravimetric results, with the differences ranging from -1.28% to 0.94% and from -0.67% to 1.35%, respectively. These findings propose new insights into the influencing mechanisms of soil moisture and structure on the thermal desorption of organic pollutants. The extended kinetic model can provide reference for future kinetic research and guide practical site remediation.

An informative short-term study on the impacts of a triclocarban/weathered multi-walled carbon nanotube-adsorbed complex to benthic organisms

Freshwater organisms are suitable models to study the fate of environmental pollutants. Due to their versatile and everyday use, many environmental pollutants such as triclocarban (TCC) or multi-walled carbon nanotubes (MWCNTs) enter environmental compartments very easily. TCC is known as a disinfectant and is declared as a highly aquatic toxicant. Multi-walled carbon nanotubes are used, e.g., in the automotive industry to improve plastic properties. Both TCCs and MWCNTs can pose major pollution hazards to various organisms. In addition, these substances can bind to each other due to their tendency to interact via strong hydrophobic interactions. Therefore, a short-term test was conducted to investigate the effects of the individual chemicals TCC and weathered MWCNTs (wMWCNTs) on a benthic biofilm and a grazing organism, Lymnaea stagnalis. Furthermore, the two compounds were coupled by an adsorption experiment resulting in a coupled complex formation (TCC + wMWCNTs). L. stagnalis showed no effects in terms of mortality. For benthic biofilm, the coupling test (TCC + wMWCNTs) showed a decrease of 58% in chlorophyll a (Chl-a) concentration. The main effect could be attributed to the wMWCNTs' exposure alone (decrease of 82%), but not to presence of TCC. The concentration range of Chl-a upon TCC exposure alone was comparable to that in the control group (32 and 37 µg/cm2). With respect to the particulate organic carbon (POC) concentration, very similar results were found for the solvent control, the TCC, and also for the TCC + wMWCNTs group (3, 2.9, and 2.9 mg/cm2). In contrast to the control, a significant increase in POC concentration (100%) was observed for wMWCNTs, but no synergistic effect of TCC + wMWCNTs was detected.

Unveiling the contemporary progress of graphene-based nanomaterials with a particular focus on the removal of contaminants from water: a comprehensive review

Water scarcity and pollution pose significant challenges to global environmental sustainability and public health. As these concerns intensify, the quest for innovative and efficient water treatment technologies becomes paramount. In recent years, graphene-based nanomaterials have emerged as frontrunners in this pursuit, showcasing exceptional properties that hold immense promise for addressing water contamination issues. Graphene, a single layer of carbon atoms arranged in a hexagonal lattice, exhibits extraordinary mechanical, electrical, and chemical properties. These inherent characteristics have led to a surge of interest in leveraging graphene derivatives, such as graphene oxide (GO), reduced graphene oxide and functionalized graphene, for water treatment applications. The ability of graphene-based nanomaterials to adsorb, catalyze, and photocatalyze contaminants makes them highly versatile in addressing diverse pollutants present in water sources. This review will delve into the synthesis methods employed for graphene-based nanomaterials and explore the structural modifications and functionalization strategies implemented to increase their pollutant removal performance in water treatment. By offering a critical analysis of existing literature and highlighting recent innovations, it will guide future research toward the rational design and optimization of graphene-based nanomaterials for water decontamination. The exploration of interdisciplinary approaches and cutting-edge technologies underscores the evolving landscape of graphene-based water treatment, fostering a path toward sustainable and scalable solutions. Overall, the authors believe that this review will serve as a valuable resource for researchers, engineers, and policymakers working toward sustainable and effective solutions for water purification.

Magnetic two-dimensional nanocomposites for multimodal antitumor therapy: a recent review

Magnetic two-dimensional nanocomposites (M2D NCs) that synergistically combine magnetic nanomedicine and 2D nanomaterials have emerged in multimodal antitumor therapy, attracting great interest in materials science and biomedical engineering. This review provides a summary of the recent advances of M2D NCs and their multimodal antitumor applications. We first introduce the design and fabrication of M2D NCs, followed by discussing new types of M2D NCs that have been recently reported. Then, a detailed analysis and discussions about the different types of M2D NCs are presented based on the structural categories of 2D NMs, including 2D graphene, transition metal dichalcogenides (TMDs), transition metal carbides/nitrides/carbonitrides (MXenes), black phosphorus (BP), layered double hydroxides (LDHs), metal organic frameworks (MOFs), covalent organic frameworks (COFs) and other 2D nanomaterials. In particular, we focus on the synthesis strategies, magnetic or optical responsive performance, and the versatile antitumor applications, which include magnetic hyperthermia therapy (MHT), photothermal therapy (PTT), photodynamic therapy (PDT), drug delivery, immunotherapy and multimodal imaging. We conclude the review by proposing future developments with an emphasis on the mass production and biodegradation mechanism of the M2D NCs. This work is expected to provide a comprehensive overview to researchers and engineers who are interested in such a research field and promote the clinical translation of M2D NCs in practical applications.

Conversion of PET Bottle Waste into a Terephthalic Acid-Based Metal-Organic Framework for Removing Plastic Nanoparticles from Water

Micro- and nanoparticles of plastic waste are considered emerging pollutants with significant environmental and health impacts at high concentrations or prolonged exposure time. Here we report the synthesis and characterization of a known metal-organic framework (MOF) using terephthalic acid (TPA) recovered from the hydrolysis of polyethylene terephthalate (PET) bottle waste. This approach adds value to the existing large amounts of bottle waste in the environment. Fully characterized zinc-TPA MOF (MOF-5) was used for the extraction and removal of engineered polyvinyl chloride (PVC) and polymethylmethacrylate (PMMA) nanoparticles from water with a high efficiency of 97% and 95%, respectively. Kinetic and isotherm models for the adsorption of polymer nanoparticles (PNPs) on the MOF surface were investigated to understand the mechanism. The Qmax for PVC and PMMA NPs were recorded as 56.65 mg/g and 33.32 mg/g, respectively. MOF-5 was characterized before and after adsorption of PNPs on the surface of MOF-5 using a range of techniques. After adsorption, the MOF-5 was successfully regenerated and reused for the adsorption and removal of PNPs, showing consistent results for five adsorption cycles with a removal rate of 83-85%. MOF-5 was characterized before and after adsorption of PNPs on the surface using a range of techniques. The MOF-5 with PNPs on the surface was successfully regenerated and reused for the adsorption and removal of polymer nanoparticles, showing consistent results for five extraction cycles. As a proof of concept, MOF-5 was also used to remove plastic particles from commercially available body scrub gel solutions. Such methods and materials are needed to mitigate the health hazards caused by emerging micro- and nanoplastic pollutants in the environment.

Recent progress of heterogeneous catalysts for transfer hydrogenation under the background of carbon neutrality

Under the background of carbon neutrality, the direct conversion of greenhouse CO2 to high value added fuels and chemicals is becoming an important and promising technology. Among them, the generation of liquid C1 products (formic acid and methanol) has made great progress; nevertheless, it encounters the problem of how to use it efficiently to solve the overcapacity issue. In this review, we suggest that the catalytic transfer hydrogenation using formic acid and methanol as the hydrogen sources is a critical and potential route for the substitution for the fossil fuel-derived H2 to generate essential bulk and fine chemicals. We mainly focus on summarizing the recent progress of heterogeneous catalysts in such reactions, including thermal- and photo-catalytic processes. Finally, we also propose some challenges and opportunities for this development.

Emerging environmentally friendly bio-based nanocomposites for the efficient removal of dyes and micropollutants from wastewater by adsorption: a comprehensive review

Water scarcity will worsen due to population growth, urbanization, and climate change. Addressing this issue requires developing energy-efficient and cost-effective water purification technologies. One approach is to use biomass to make bio-based materials (BBMs) with valuable attributes. This aligns with the goal of environmental conservation and waste management. Furthermore, the use of biomass is advantageous because it is readily available, economical, and has minimal secondary environmental impact. Biomass materials are ideal for water purification because they are abundant and contain important functional groups like hydroxyl, carboxyl, and amino groups. Functional groups are important for modifying and absorbing contaminants in water. Single-sourced biomass has limitations such as weak mechanical strength, limited adsorption capacity, and chemical instability. Investing in research and development is crucial for the development of efficient methods to produce BBMs and establish suitable water purification application models. This review covers BBM production, modification, functionalization, and their applications in wastewater treatment. These applications include oil-water separation, membrane filtration, micropollutant removal, and organic pollutant elimination. This review explores the production processes and properties of BBMs from biopolymers, highlighting their potential for water treatment applications. Furthermore, this review discusses the future prospects and challenges of developing BBMs for water treatment and usage. Finally, this review highlights the importance of BBMs in solving water purification challenges and encourages innovative solutions in this field.

Theoretical design of transition metal-doped oxo-triarylmethyl as a disposable platform for adsorption of ibuprofen

Emerging environmental contaminants have become a crucial environmental issue because of the highly toxic effluents emitted by factories. Ibuprofen (IBP), as a typical anti-inflammatory drug, is frequently detected in water sources. Therefore, its removal using various adsorbents has drawn great interest. Herein, the structural, electronic, energetic, and optical properties of pristine oxo-triarylmethyl (oxTAM) and transition metal-doped oxo-triarylmethyl (TM@oxTAM, TM = Sc, Ti, V, Cr, and Mn) for adsorption of the IBU drug were investigated using density functional theory (DFT) calculations implemented in Gaussian and VASP codes. Frontier molecular orbital (FMO), density of states (DOS), and electronic band structure results demonstrated that transition metal-doped oxTAM causes a significant reduction in the energy band gap (Eg) value of pristine oxTAM, with the highest decrease (30.14 %) in the case of Mn@oxTAM. It was found that transition metal doping onto oxTAM leads to an increase in the adsorption energies (1.20-2.64 eV) and charge density between transition metal and IBU. Natural bond orbital (NBO) analysis revealed that charge was effectively transferred from the IBU towards the transition metal, which was further analyzed by charge decomposition analysis (CDA). Furthermore, quantum theory of atoms in molecules (QTAIM), interaction region indicator (IRI), electron localization function (ELF), and radial distribution function (RDF) analyses revealed that the IBU is adsorbed on the Sc@oxTAM surface via covalent interactions, while electrostatic with partially covalent interactions are dominated in other IBU/TM@oxTAM complexes. The results suggest that TM doping on the oxTAM provides a new insight for developing photocatalyst-based covalent organic frameworks (COFs) to remove emerging pollutants in wastewater.

Recycling and Reusing of Graphite from Retired Lithium-ion Batteries: A Review

The proliferation of rechargeable lithium-ion batteries (LIBs) over the past decade has led to a significant increase in the number of electric vehicles (EVs) powered by these batteries reaching the end of their lifespan. With retired EVs becoming more prevalent, recycling and reusing their components, particularly graphite, has become imperative as the world transitions toward electric mobility. Graphite constitutes ≈20% of LIBs by weight, making it a valuable resource to be conserved. This review presents an in-depth analysis of the current global graphite mining landscape and explores potential opportunities for the "second life" of graphitefrom depleted LIBs. Various recycling and reactivation technologies in both industry and academia are discussed, along with potential applications for recycled graphite forming a vital aspect of the waste management hierarchy. Furthermore, this review addresses the future challenges faced by the recycling industry in dealing with expired LIBs, encompassing environmental, economic, legal, and regulatory considerations. In conclusion, this review provides a comprehensive overview of the developments in recycling and reusing graphite from retired LIBs, offering valuable insights for forthcoming large-scale recycling efforts.

Recent advances in green technology and Industrial Revolution 4.0 for a sustainable future

This review gives concise information on green technology (GT) and Industrial Revolution 4.0 (IR 4.0). Climate change has begun showing its impacts on the environment, and the change is real. The devastating COVID-19 pandemic has negatively affected lives and the world from the deadly consequences at a social, economic, and environmental level. In order to balance this crisis, there is a need to transition toward green, sustainable forms of living and practices. We need green innovative technologies (GTI) and Internet of Things (IoT) technologies to develop green, durable, biodegradable, and eco-friendly products for a sustainable future. GTI encompasses all innovations that contribute to developing significant products, services, or processes that lower environmental harm, impact, and worsening while augmenting natural resource utilization. Sensors are typically used in IoT environmental monitoring applications to aid ecological safety by nursing air or water quality, atmospheric or soil conditions, and even monitoring species' movements and habitats. The industries and the governments are working together, have come up with solutions-the Green New Deal, carbon pricing, use of bio-based products as biopesticides, in biopharmaceuticals, green building materials, bio-based membrane filters for removing pollutants, bioenergy, biofuels and are essential for the green recovery of world economies. Environmental biotechnology, Green Chemical Engineering, more bio-based materials to separate pollutants, and product engineering of advanced materials and environmental economies are discussed here to pave the way toward the Sustainable Development Goals (SDGs) set by the UN and achieve the much-needed IR 4.0 for a greener-balanced environment and a sustainable future.

Surface/interfacial transport through pores control desalination mechanisms in 2D carbon-based membranes

The shortage of freshwater is a critical concern for contemporary society, and reverse osmosis desalination technology has gathered considerable attention as a potential solution to this problem. It has been recognized that the desalination process involving water flow through angstrom-sized pores has tremendous potential. However, it is challenging to obtain angstrom-sized pore structures with internal mass transfer and surface/interface properties matching the application conditions. Herein, a two-dimensional (2D) zeolite-like carbon structure (Carzeo-ANG) was constructed with unique angstrom-sized pores in the zeolite structure; then, the surface/interfacial transport behavior and percolation effect of the Carzeo-ANG desalination membrane were evaluated by density functional theory (DFT) calculations and classical molecular dynamics. The first-principles calculations in density functional theory were implemented through the Vienna ab initio simulation package (VASP), which is a commercial package for the simulation of carbon-based materials. The results show that Carzeo-ANG is periodically distributed with angstrom-sized pores (effective diameter = 5.4 Å) of dodecacyclic carbon rings, which ensure structural stability while maintaining sufficient mechanical strength. The remarkable salt-ion adsorption properties and mass transfer activity combined with the reasonable density distribution and free energy barrier for water molecules endow the membrane with superior desalination ability. At the pressure of 80 MPa, the rejection efficiency of Cl- and Na+ were 100% and 96.25%, and the membrane could achieve a water flux of 132.71 L cm-2 day-1 MPa-1. Moreover, the interconnected electronic structure of Carzeo-ANG imparts a self-cleaning effect.

Fabrication of bimetallic-doped materials derived from a Cu-based complex for enhanced dye adsorption and iodine capture

In this work, we used Cu(II) ions, a bis-pyridyl-bis-amide ligand [N,N'-bis(4-pyridinecarboxamide)-1,2-cyclohexane (4-bpah)], and an aromatic dicarboxylic acid [1,4-cyclohexanedicarboxylic acid (H2CHDA)] to construct a 1D binuclear Cu-based complex, namely {[Cu3(4-bpah)(CHDA)3(H2O)]·2H2O}n (1). Moreover, we also developed a facile method to synthesize two monometallic/bimetallic-doped materials which were derived from the Cu complex (C-N-1 and C-V-1, which were doped with nitrogen and vanadium, respectively). The as-synthesized derived materials were fully characterized and the iodine sorption/release capabilities were investigated in detail. We performed iodine adsorption experiments on the two monometallic/bimetallic-doped materials and found that C-N-1 and C-V-1 possess highly efficient adsorption activities for the adsorption of iodine from solution. The C-N-1 and C-V-1 complexes exhibited remarkable adsorption capacities of 1141.60 and 1170.70 mg g-1, respectively, for iodine from a cyclohexane solution. Moreover, the dye adsorption properties of C-N-1 and C-V-1 were also investigated in detail. The obtained C-N-1 and C-V-1 exhibit effective dye uptake performances in water solution. The adsorption of Congo red (CR) on a single metal carbon material C-N-1 doped with heteroatoms reached equilibrium within 240 min and reached an adsorption capacity of 1357.00 mg g-1 and the adsorption capacities of C-V-1 for methylene blue (MB), gentian violet (GV), rhodamine B (RhB), and CR at room temperature were found to be 187.60, 190.60 and 108.10 and 1501.00 mg g-1 in 180 min, respectively. By comparison, we found that doping vanadium could play an important role in the adsorption processes. The adsorption capacity of C-V-1 (containing the vanadium in its structure) was relatively higher than that of C-N-1, which indicated that the introduction of non-noble metals may effectively tune the adsorption kinetics activity and the introduction of noble metals can change the surface electronegativity of porous carbon materials, thus leading to significantly improved adsorption capabilities.

Pharmaceutical residues in the ecosystem: Antibiotic resistance, health impacts, and removal techniques

Hospital wastewater has emerged as a major category of environmental pollutants over the past two decades, but its prevalence in freshwater is less well documented than other types of contaminants. Due to compound complexity and improper operations, conventional treatment is unable to remove pharmaceuticals from hospital wastewater. Advanced treatment technologies may eliminate pharmaceuticals, but there are still concerns about cost and energy use. There should be a legal and regulatory framework in place to control the flow of hospital wastewater. Here, we review the latest scientific knowledge regarding effective pharmaceutical cleanup strategies and treatment procedures to achieve that goal. Successful treatment techniques are also highlighted, such as pre-treatment or on-site facilities that control hospital wastewater where it is used in hospitals. Due to the prioritization, the regulatory agencies will be able to assess and monitor the concentration of pharmaceutical residues in groundwater, surface water, and drinking water. Based on the data obtained, the conventional WWTPs remove 10-60% of pharmaceutical residues. However, most PhACs are eliminated during the secondary or advanced therapy stages, and an overall elimination rate higher than 90% can be achieved. This review also highlights and compares the suitability of currently used treatment technologies and identifies the merits and demerits of each technology to upgrade the system to tackle future challenges. For this reason, pharmaceutical compound rankings in regulatory agencies should be the subject of prospective studies.

Lanthanum nanoparticle (La2O3)-loaded adsorbents for removal of hexavalent chromium: a kinetics, isotherm, and thermodynamic study

Nanocomposite adsorbents for wastewater treatment gained popularity in recent times. In the present study, nanoparticles prepared from lanthanum have been loaded on the powdered form of aquatic plants Salvinia molesta (S. molesta) and Typha latifolia (T. latifolia). These new adsorbents were NPS (nanoparticle-loaded S. molesta) and NPT (nanoparticle-loaded T. latifolia). The batch study was carried out to assess the effect of several factors on the adsorption of Cr(VI) by novel adsorbents NPS and NPT. XRD, SEM, FTIR, EDX, and Zeta potential were used for the characterization of nanoparticles formed and novel adsorbents. The maximal adsorption was noticed by both adsorbents at pH 1, 20 ppm of initial metal concentration, and 1 h of contact period with 150 rpm at 25 ℃. The adsorbent dose of 60 mg and 80 mg was observed as the equilibrium dose for NPS and NPT, respectively. The maximum adsorption capacity observed was 27.18 mg/g for NPS and 19.85 mg/g for NPT. Freundlich isotherm was better fitted for both adsorbents. Pseudo-second-order kinetics depicts the better mechanism of adsorption with R2 = 0.9995 and 0.9982 for NPS and NPT, respectively. Thermodynamic parameters show that the adsorption process was exothermic and spontaneous.

Current trends in the detection and removal of heavy metal ions using functional materials

The shortage of freshwater resources caused by heavy metal pollution is an acute global issue, which has a great impact on environmental protection and human health. Therefore, the exploitation of new strategies for designing and synthesizing green, efficient, and economical materials for the detection and removal of heavy metal ions is crucial. Among the various methods for the detection and removal of heavy ions, advanced functional systems including nanomaterials, polymers, porous materials, and biomaterials have attracted considerable attention over the past several years due to their capabilities of real-time detection, excellent removal efficiency, anti-interference, quick response, high selectivity, and low limit of detection. In this tutorial review, we review the general design principles underlying the aforementioned functional materials, and in particular highlight the fundamental mechanisms and specific examples of detecting and removing heavy metal ions. Additionally, the methods which enhance water purification quality using these functional materials have been reviewed, also current challenges and opportunities in this exciting field have been highlighted, including the fabrication, subsequent treatment, and potential future applications of such functional materials. We envision that this tutorial review will provide invaluable guidance for the design of functional materials tailored towards the detection and removal of heavy metals, thereby expediting the development of high-performance materials and fostering the development of more efficient approaches to water pollution remediation.

Development of metal free carbon catalyst derived from Parthenium hysterophorus for the electrochemical detection of dopamine

Parthenium hysterophorus, one of the seven most hazardous weeds is widely known for its allergic, respiratory and skin-related disorders. It is also known to affect biodiversity and ecology. For eradication of the weed, its effective utilization for the successful synthesis of carbon-based nanomaterial is a potent management strategy. In this study, reduced graphene oxide (rGO) was synthesized from weed leaf extract through a hydrothermal-assisted carbonization method. The crystallinity and geometry of the as-synthesized nanostructure are confirmed from the X-ray diffraction study, while the chemical architecture of the nanomaterial is ascertained through X-ray photoelectron spectroscopy. The stacking of flat graphene-like layers with a size range of ∼200-300 nm is visualized through high-resolution transmission electron microscopy images. Further, the as-synthesized carbon nanomaterial is advanced as an effective and highly sensitive electrochemical biosensor for dopamine, a vital neurotransmitter of the human brain. Nanomaterial oxidizes dopamine at a much lower potential (0.13 V) than other metal-based nanocomposites. Moreover, the obtained sensitivity (13.75 and 3.31 μA μM-1 cm-2), detection limit (0.6 and 0.8 μM), the limit of quantification (2.2 and 2.7 μM) and reproducibility calculated through cyclic voltammetry/differential pulse voltammetry respectively outcompete many metal-based nanocomposites that were previously used for the sensing of dopamine. This study boosts the research on the metal-free carbon-based nanomaterial derived from waste plant biomass.

Treatment of textile wastewater using carbon-based nanomaterials as adsorbents: a review

Waste derived from the textile industry can contain a wide variety of pollutants of organic and inorganic natures, such as dyes (e.g., acid, basic, reactive, mordant dyes) and toxic metals (e.g., lead, chromium, cadmium). The presence of pollutants at high concentrations in textile waste makes them relevant sources of pollution in the environment. To solve this problem, various technologies have been developed for the removal of pollutants from these matrices. Thus, adsorption emerges as an efficient alternative for textile waste remediation, providing advantages as simplicity of operation, economy, possibility of using different adsorbent materials, and developing on-line systems that allow the reuse of the adsorbent during several adsorption/desorption cycles. This review will initially propose an introduction to the adsorption world, its fundamentals, and aspects related to kinetics, equilibrium, and thermodynamics. The possible mechanisms through which a pollutant can be retained on an adsorbent will be explained. The analytical techniques that offer valuable information to characterize the solid phases as well as each adsorbate/adsorbent system will be also commented. The most common synthesis techniques to obtain carbon nano-adsorbents have been also presented. In addition, the latest advances about the use of these adsorbents for the removal of pollutants from textile waste will be presented and discussed. The contributions reported in this manuscript demonstrated the use of highly efficient carbon-based nano-adsorbents for the removal of both organic and inorganic pollutants, reaching removal percentages from 65 to 100%.

High-capacity/high-rate hybrid column for high-performance ion exchange

Herein, a fixed-bed high-capacity/high-rate (HC/HR) hybrid column was developed using commercial ion-exchange beads (IEBs) and ion-exchange fibers (IEFs). The as-fabricated HC/HR hybrid column exhibited excellent breakthrough bed volume (BV) and utilization efficiency of capacity (UEC) at a high service flow rate (SFR) for the adsorption of Cd(II). The IEBs displayed a high adsorption capacity of 235.2 ± 9.8 mg g^-1 and slow adsorption kinetics (k₂ = 0.0001 g mg^-1 min^-1) for the sorption of Cd(II); meanwhile, the IEFs showed a maximum adsorption capacity of only 146.3 ± 7.5 mg g^-1, which is lower than that of the IEBs, but fast kinetics (k₂ = 0.0130 g mg^-1 min^-1). At an SFR of 104.23 BV h^-1, the HC/HR hybrid column showed excellent performance for the sorption of Cd(II), having a high breakthrough BV of 1009.11 and a UEC of 92.86%; these values are much higher than those of the IEB-packed column. Furthermore, at an increased SFR (318.47 BV h^-1), the HC/HR hybrid column maintained its high performance, demonstrating a breakthrough BV of 568.80 and UEC of 83.90%. The regeneration experiment indicates that 97% of the initial capacity was retained. Thus, the HC/HR hybrid column could easily be applied to existing column systems and shows promising performance in ion-exchange processes.

Removal of Acetaminophen Drug from Wastewater by Fe3O4 and ZSM-5 Materials

Adsorption of toxic compounds from water using zeolites and magnetite was developed due to the various advantages of their applicability. In the last twenty years, the use of zeolite-based compositions in the form of zeolite/inorganic or zeolite/polymer and magnetite has been accelerated for the adsorption of emergent compounds from water sources. The main adsorption mechanisms using zeolite and magnetite nanomaterials are high surface adsorption, ion exchange capacity and electrostatic interaction. This paper shows the capacity of Fe₃O₄ and ZSM-5 nanomaterials of adsorbing the emerging pollutant acetaminophen (paracetamol) during the treatment of wastewater. The efficiencies of the Fe₃O₄ and ZSM-5 in the wastewater process were systematically investigated using adsorption kinetics. During the study, the concentration of acetaminophen in the wastewater was varied from 50 to 280 mg/L, and the maximum Fe₃O₄ adsorption capacity increased from 25.3 to 68.9 mg/g. The adsorption capacity of each studied material was performed for three pH values (4, 6, 8) of the wastewater. Langmuir and Freundlich isotherm models were used to characterize acetaminophen adsorption on Fe₃O₄ and ZSM-5 materials. The highest efficiencies in the treatment of wastewater were obtained at a pH value of 6. Fe₃O₄ nanomaterial presented a higher removal efficiency (84.6%) compared to ZSM-5 nanomaterial (75.4%). The results of the experiments show that both materials have a potential to be used as an effective adsorbents for the removal of acetaminophen from wastewater.

Removal Performance of KOH-Modified Biochar from Tropical Biomass on Tetracycline and Cr(VI)

Biochar can be used to address the excessive use of tetracycline and micronutrient chromium (Cr) in wastewater that potentially threatens human health. However, there is little information about how the biochar, made from different tropical biomass, facilitates tetracycline and hexavalent chromium (Cr(VI)) removal from aqueous solution. In this study, biochar was prepared from cassava stalk, rubber wood and sugarcane bagasse, then further modified with KOH to remove tetracycline and Cr(VI). Results showed that pore characteristics and redox capacity of biochar were improved after modification. KOH-modified rubber wood biochar had the highest removal of tetracycline and Cr(VI), 1.85 times and 6 times higher than unmodified biochar. Tetracycline and Cr(VI) can be removed by electrostatic adsorption, reduction reaction, π-π stacking interaction, hydrogen bonding, pore filling effect and surface complexation. These observations will improve the understanding of the simultaneous removal of tetracycline and anionic heavy metals from wastewater.

Remediation of environmental toxicants using carbonaceous materials: opportunity and challenges

Adsorption and photocatalytic properties of carbonaceous materials, viz., carbon nanotubes (CNTs), fullerene, graphene, graphene oxide, carbon nanofiber nanospheres, and activated carbon, are the legitimate weapons for the remediation of emerging and persistent inorganic/organic contaminants, heavy metals, and radionucleotides from the environment. High surface area, low or non-toxic nature, ease of synthesis, regeneration, and chemical modification of carbonaceous material make them ideal for the removal of toxicants. The research techniques investigated during the last decade for the elimination of environmental toxicants using carbonaceous materials are reviewed to offer comprehensive insight into the mechanism, efficiency, applications, advantages, and shortcomings. Opportunities and challenges associated with carbon materials have been discussed to suggest future perspectives in the remediation of environmental toxicants.

Photothermal Nanomaterials: A Powerful Light-to-Heat Converter

All forms of energy follow the law of conservation of energy, by which they can be neither created nor destroyed. Light-to-heat conversion as a traditional yet constantly evolving means of converting light into thermal energy has been of enduring appeal to researchers and the public. With the continuous development of advanced nanotechnologies, a variety of photothermal nanomaterials have been endowed with excellent light harvesting and photothermal conversion capabilities for exploring fascinating and prospective applications. Herein we review the latest progresses on photothermal nanomaterials, with a focus on their underlying mechanisms as powerful light-to-heat converters. We present an extensive catalogue of nanostructured photothermal materials, including metallic/semiconductor structures, carbon materials, organic polymers, and two-dimensional materials. The proper material selection and rational structural design for improving the photothermal performance are then discussed. We also provide a representative overview of the latest techniques for probing photothermally generated heat at the nanoscale. We finally review the recent significant developments of photothermal applications and give a brief outlook on the current challenges and future directions of photothermal nanomaterials.

Metalloporphyrin reduced C70 fullerenes as adsorbents and detectors of ethenone; A DFT, NBO, and TD-DFT study

In the present work, the structure and electronic properties of Ti-, Cr-, Fe-, Ni-, Zn-, and Cu-inserted in porphyrin-reduced C70 fullerenes (TM-PIC70Fs) and their interactions with the ethenone were studied using DFT, NBO, and TD-DFT at CAM-B3LYP/6-31G(d) level of theory. 2.89-3.83 and 4.02-4.56 eV were obtained for the HOMO-LUMO gap energies and work functions of TM-PIC70Fs, respectively, compared with 3.76 and 4.54 eV for PIC70F. Among considered TM-PIC70Fs, the adsorption of the ethenone on Ti-PIC70F appreciably changed the HOMO-LUMO energy gap and work function. Consequently, Ti-PIC70F may be used as the ethenone's electronic conductivity and work function types sensor. According to calculated UV-visible spectra, the ethenone adsorption may change the color of Fe- and Ti-PIC70Fs. Therefore, they can be used as color-changing sensors of ethenone. In addition, Ti-, Cr-, Fe-, and Zn-PIC70Fs can be employed as suitable adsorbents of ethenone. Among proper sensors and adsorbents of ethenone, Cr-, Fe-, and Zn-PIC70Fs may be recovered and reused.

The control efficiency and mechanism of heavy metals by permeable pavement system in runoff based on enhanced infiltration materials

As one of the commonly used stormwater management measures, permeable pavement system (PPS) played a prominent role in controlling runoff pollution and alleviating urban waterlogging. In this study, new enhanced infiltration materials (construction waste brick, coal gangue, activated carbon, multi-walled carbon nanotube, multi-layer graphene) were applied in PPS and the control efficiency and mechanism of typical heavy metals (HMs, Mn²⁺, Pb²⁺, Zn²⁺, Cu²⁺, Cd²⁺, Ni²⁺) was investigated in runoff. Furthermore, the influences of different rainfall intensities and antecedent dry periods on HMs removal by PPS were evaluated. The results showed that all PPS with enhanced infiltration materials have little leaching effect on HMs (＜3 μg/L). All the selected enhanced infiltration materials meet the requirements of PPS. The concentration of HMs in the effluent of PPS dropped sharply first, followed rebounded and then maintained at a stable range. Activated carbon PPS (AC), Multi-walled carbon nanotube PPS (MCN), and Multi-layer graphene PPS (MG) could significantly improve the control effect of PPS on nearly all selected HMs. The average removal rates of AC, MCN and MG for six HMs were 75.48%-99.35%, 81.30%-97.59%, and 73.03%-99.33%, respectively. Compared with Traditional PPS (TR), the effluent concentrations of HMs in construction waste brick PPS (CW) and coal gangue PPS (CG) were relatively higher and unstable. AC, CN and MG could adapt to different rainfall conditions and the maximum removal rates of most HMs exceed to 99%. With antecedent dry periods increased, the control effect of HMs was significantly improved. The influences of the antecedent drying period on HMs removal followed as: CW＞CG＞TR＞MG＞CN＞AC. This study provided novel methods to eliminating HMs in runoff and provides implications for the design of PPS.

Existing Filtration Treatment on Drinking Water Process and Concerns Issues

Water is one of the main sources of life's survival. It is mandatory to have good-quality water, especially for drinking. Many types of available filtration treatment can produce high-quality drinking water. As a result, it is intriguing to determine which treatment is the best. This paper provides a review of available filtration technology specifically for drinking water treatment, including both conventional and advanced treatments, while focusing on membrane filtration treatment. This review covers the concerns that usually exist in membrane filtration treatment, namely membrane fouling. Here, the parameters that influence fouling are identified. This paper also discusses the different ways to handle fouling, either based on prevention, prediction, or control automation. According to the findings, the most common treatment for fouling was prevention. However, this treatment required the use of chemical agents, which will eventually affect human health. The prediction process was usually used to circumvent the process of fouling development. Based on our reviews up to now, there are a limited number of researchers who study membrane fouling control based on automation. Frequently, the treatment method and control strategy are determined individually.

Green synthesis of iron oxide nanoparticles derived from water and methanol extract of Centaurea solstitialis leaves and tested for antimicrobial activity and dye decolorization capability

In this research, nanoparticles derived from water extract of Centaurea solstitialis leaves were used as green adsorbent in Fenton reaction for Reactive Red 180 (RR180) and Basic Red 18 (BR18) dyes removal. At optimum operating conditions, nanoparticles proved high performance in the tested dyes removal with more than 98% of removal elimination. The free-radical scavenging, DNA nuclease, biofilm inhibition capability, antimicrobial activity, microbial cell viability, and antimicrobial photodynamic therapy activities of the iron oxide nanoparticles (FeO-NPs) derived from water and methanol extract of plant were investigated. Each of the following analysis: SEM-EDX, XRD, and Zeta potential was implemented for the prepared NPs characterization and to describe their morphology, composition and its behavior in an aqueous solution, respectively. It was found that, the DPPH scavenging activities increased when the amount of nanoparticles increased. The highest radical scavenging activity achieved with FeO-NPs derived from water extract of plant as 97.41% at 200 mg/L. The new green synthesized FeO-NPs demonstrated good DNA cleavage activity. FeO-NPs showed good in vitro antimicrobial activities against human pathogens. The results showed that both synthesized FeO-NPs displayed 100% antimicrobial photodynamic therapy activity after LED irradiation. The water extract of FeO-NPs and methanol extract of FeO-NPs also showed a significant biofilm inhibition.

Poly(ethylene glycol) Diacrylate Hydrogel with Silver Nanoclusters for Water Pb(II) Ions Filtering

Poly(ethylene glycol) diacrylate (PEGDA) hydrogels modified with luminescent silver nanoclusters (AgNCs) are synthesized by a photo-crosslinking process. The hybrid material thus obtained is employed to filter Pb(II) polluted water. Under the best conditions, the nanocomposite is able to remove up to 80-90% of lead contaminant, depending on the filter composition. The experimental results indicate that the adsorption process of Pb(II) onto the modified filter can be well modeled using the Freundlich isotherm, thus revealing that the chemisorption is the driving process of Pb(II) adsorption. In addition, the parameter n in the Freundlich model suggests that the adsorption process of Pb(II) ions in the modified hydrogel is favored. Based on the obtained remarkable contaminant uptake capacity and the overall low cost, this hybrid system appears to be a promising sorbent material for the removal of Pb(II) ions from aqueous media.

Sustainable synthesis of graphene sand composite from waste cooking oil for dye removal

Waste cooking oil (WCO) appears to be a potential carbonaceous source for synthesizing graphene sand composite (GSC) adsorbent in removing pollutants. This study presents a green synthesis method of GSC using WCO as a sustainable carbon source for the synthesis of GSC through the thermal graphitization method. Characterization analysis conducted on GSCWCO verified the successful coating of WCO onto the sand surface and conversion to graphene, which possessed distinct functional groups and features of graphene materials. GSCWCO adsorbent effectiveness in removing Congo Red dye through batch adsorption was studied under the influence of different initial concentrations (20 to 100 mg/L), and the optimum pH (pH 2 to 10), contact time (5 to 240 min), and temperature (25 to 45 °C) were investigated. The GSCWCO showed removal rates of 91.5% achieved at an initial dye concentration of 20 mg L-1, 1.0 g of adsorbent dosage, a temperature of 25 °C, and 150 min of contact time. The GSCWCO exhibited a maximum capacity of 5.52 mg g-1, was well-fitted to the Freundlich isotherm model with an R2 value of 0.989 and had an adsorption mechanism that followed the pseudo-second-order kinetic model. Negative values of enthalpy (ΔH) and Gibbs free energy (ΔG) revealed that CR adsorption onto GSCWCO was a spontaneous and exothermic process. The presence of functional groups on the surface of GSCWCO with such interactions (π-π attractive forces, hydrophobic forces, and hydrogen bonding) was responsible for the anionic dye removal. Regeneration of GSCWCO adsorbent declined after four cycles, possibly due to the chemisorption of dyes with GSC that resulted in inefficient adsorption. Being a waste-to-wealth product, GSCWCO possessed great potential to be used for water treatment and simultaneously benefited the environment through the effort to reduce the excessive discharge of WCO.

A review on recent advancements on removal of harmful metal/metal ions using graphene oxide: Experimental and theoretical approaches

Graphene oxide is a two-dimensional carbon nanomaterial and has gained huge popularity over the last decade. Because, the graphene oxide can be dispersed in water easily and it is one of the most researched two-dimensional materials in the current time. The extraordinary properties shown by graphene oxide (GO) are due to its unique chemical structure; includes various hydrophilic functional groups containing oxygen such as carboxyl, hydroxyl, carbonyl and tiny sp² carbon domains surrounded by sp³ domains. These groups are very peculiar for various applications as they allow covalent functionalisation with a plethora of compounds. Large surface area, intrinsic fluorescence, excellent surface functionality, amphiphilicity, improved conductivity, high adsorption capacity and superior biocompatibility are some of the chemical properties have drawn research from various fields. Graphene oxide has various interactions such as coordination, chelation, hydrogen bonding, electrostatic interaction, hydrophobic effects, π-π interaction, acid base interaction etc., with various metal ions. This review is focused on the removal of metals and metal ions due to their interactions mentioned above. Further, potential of composites of graphene oxide in the removal of metal and metal ions is also discussed. Further, the current challenges in this field at industrial-scale are also discussed.

Preconcentration and Removal of Pb(II) Ions from Aqueous Solutions Using Graphene-Based Nanomaterials

Direct determination of lead trace concentration in the presence of relatively complex matrices is often a problem. Thus, its preconcentration and separation are necessary in the analytical procedures. Graphene-based nanomaterials have attracted significant interest as potential adsorbents for Pb(II) preconcentration and removal due to their high specific surface area, exceptional porosities, numerous adsorption sites and functionalization ease. Particularly, incorporation of magnetic particles with graphene adsorbents offers an effective approach to overcome the separation problems after a lead enrichment step. This paper summarizes the developments in the applications of graphene-based adsorbents in conventional solid-phase extraction column packing and its alternative approaches in the past 5 years.

Effective Removal of Metal ion and Organic Compounds by Non-Functionalized rGO

Effective removal of heavy metals from water is critical for environmental safety and public health. This work presents a reduced graphene oxide (rGO) obtained simply by using gallic acid and sodium ascorbate, without any high thermal process or complex functionalization, for effective removal of heavy metals. FTIR and Raman analysis show the effective conversion of graphene oxide (GO) into rGO and a large presence of defects in rGO. Nitrogen adsorption isotherms show a specific surface area of 83.5 m2/g. We also measure the zeta-potential of the material showing a value of -52 mV, which is lower compared to the -32 mV of GO. We use our rGO to test adsorption of several ion metals (Ag (I), Cu (II), Fe (II), Mn (II), and Pb(II)), and two organic contaminants, methylene blue and hydroquinone. In general, our rGO shows strong adsorption capacity of metals and methylene blue, with adsorption capacity of qmax = 243.9 mg/g for Pb(II), which is higher than several previous reports on non-functionalized rGO. Our adsorption capacity is still lower compared to functionalized graphene oxide compounds, such as chitosan, but at the expense of more complex synthesis. To prove the effectiveness of our rGO, we show cleaning of waste water from a paper photography processing operation that contains large residual amounts of hydroquinone, sulfites, and AgBr. We achieve 100% contaminants removal for 20% contaminant concentration and 63% removal for 60% contaminant concentration. Our work shows that our simple synthesis of rGO can be a simple and low-cost route to clean residual waters, especially in disadvantaged communities with low economical resources and limited manufacturing infrastructure.

Nanotechnology- A ray of hope for heavy metals removal

Environmental effects of heavy metal pollution are considered as a widespread problem throughout the world, as it jeopardizes human health and also reduces the sustainability of a cleaner environment. Removal of such noxious pollutants from wastewater is pivotal because it provides a propitious solution for a cleaner environment and water scarcity. Adsorption treatment plays a significant role in water remediation due to its potent treatment and low cost of adsorbents. In the last two decades, researchers have been highly focused on the modification of adsorption treatment by functionalized and surface-modified nanomaterials which has spurred intense research. The characteristics of nano adsorbents attract global scientists as it is also economically viable. This review shines its light on the functionalized nanomaterials application for heavy metals removal from wastewater and also highlights the importance of regeneration of nanomaterials in the view of visualizing the economic aspects along with a cleaner environment. The review also focused on the proper disposal of nanomaterials with crucial issues that persist in the adsorption process and also emphasize future research modification at a large-scale application in industries.

Pharmaceutical residues: One of the significant problems in achieving 'clean water for all' and its solution

With the rapid emergence of various metabolic and multiple-drug-resistant infectious diseases, new pharmaceuticals are continuously being introduced in the market. The excess production and use of pharmaceuticals and their untreated/unmetabolized release in the environment cause the contamination of aquatic ecosystem, and thus, compromise the environment and human-health. The present review provides insights into the classification, sources, occurrence, harmful impacts, and existing technologies to curb these problems. A comprehensive detail of various biological and nanotechnological strategies for the removal of pharmaceutical residues from water is critically discussed focusing on their efficiencies, and current limitations to design improved-technologies for their lab-to-field applications. Furthermore, the review highlights and suggests the scope of integrated bionanotechnological methods for enhanced removal of pharmaceutical residues from water to fulfill the United Nations Sustainable Development Goal (UN-SDG) for providing clean potable water for all.

Nano-modified feather keratin derived green and sustainable biosorbents for the remediation of heavy metals from synthetic wastewater

In this study, we employed a facile method to synthesize feather keratin derived biosorbents using water dispersed graphene oxide. The successful cross-linking of feather keratin with graphene oxide was investigated through X-ray photoelectrons spectroscopy (XPS), scanning and transmission electron microscopy, and Brunauer-Emmett-Teller (BET) analysis. The modifications resulted in increased surface area of the keratin proteins with substantial morphological changes including the development of cracked and rough patches on the surface. The chicken feather keratin/graphene oxide based biosorbents exhibited excellent performance for the simultaneous removal of metal oxyanions including arsenic (As), selenium (Se), chromium (Cr) and cations including nickel (Ni), cobalt (Co), lead (Pb), cadmium (Cd) and zinc (Zn) up to 99%, from polluted synthetic water containing 600 μgL^-1 of each metal concentration in 24 h. The insights into the biosorption mechanism revealed that the electrostatic interaction, chelation and complexation primarily contributed to the removal of multiple heavy metal ions in a single treatment. This study has demonstrated that modification of chicken feather keratin with graphene oxide is an effective way to improve its sorption capacity for removing multiple trace metal ions from contaminated water.

Synthesis of Chlorine- and Nitrogen-Containing Carbon Nanofibers for Water Purification from Chloroaromatic Compounds

Chlorine- and nitrogen-containing carbon nanofibers (CNFs) were obtained by combined catalytic pyrolysis of trichloroethylene (C₂HCl₃) and acetonitrile (CH₃CN). Their efficiency in the adsorption of 1,2-dichlorobenzene (1,2-DCB) from water has been studied. The synthesis of CNFs was carried out over self-dispersing nickel catalyst at 600 °C. The produced CNFs possess a well-defined segmented structure, high specific surface area (~300 m²/g) and high porosity (0.5-0.7 cm³/g). The addition of CH₃CN into the reaction mixture allows the introduction of nitrogen into the CNF structure and increases the volume of mesopores. As a result, the capacity of CNF towards adsorption of 1,2-DCB from its aqueous solution increased from 0.41 to 0.57 cm³/g. Regardless of the presence of N, the CNF samples exhibited a degree of 1,2-DCB adsorption from water-organic emulsion exceeding 90%. The adsorption process was shown to be well described by the Dubinin-Astakhov equation. The regeneration of the used CNF adsorbent through liquid-phase hydrodechlorination was also investigated. For this purpose, Pd nanoparticles (1.5 wt%) were deposited on the CNF surface to form the adsorbent with catalytic function. The presence of palladium was found to have a slight effect on the adsorption capacity of CNF. Further regeneration of the adsorbent-catalyst via hydrodechlorination of adsorbed 1,2-DCB was completed within 1 h with 100% conversion. The repeated use of regenerated adsorbent-catalysts for purification of solutions after the first cycle of adsorption ensures almost complete removal of 1,2-DCB.

Iron-loaded leonardite powder for Fenton oxidation of Reactive Red 180 dye removal

Fenton oxidation is an effective and valuable method for wastewater treatment. To inhibit environmental impacts and increase overall reaction efficiencies, it is important to develop advanced catalysts. This paper illustrates an experimental study on the elimination of RR180 dye from synthetic aqueous solutions with raw leonardite and different iron-loaded leonardite powders, Fe(0)-loaded leonardite, and Fe(II)-loaded leonardite. The effect of solution pH (2.0-6.0), catalyst amount (0.10-1.5 g/L), H₂O₂ concentration (10-50 µL/L), and dye concentration (10-30 ppm) was tested to achieve maximum color removal efficiency using the three catalysts. At pH = 2, color removal efficiencies were higher and more suitable. Initial experiments showed the advantage of using Fe(II)-loaded leonardite on using Fe(0)-loaded leonardite. Fe(II)-loaded leonardite catalyst was the most efficient in RR180 color removal compared to the other tested reagents. Color removal in function of solution pH did not decrease much when Fe(II)-loaded leonardite was used (100 to 96%) when pH was increased from 2.0 to 6.0. In the other hand, dye removal has been significantly affected in the case of using raw leonardite, Fe(0)-loaded leonardite (93 to 0%), and (100 to 13%) in the same pH range, respectively. At optimum experimental conditions, catalyst amount: 0.75 g/L for Fe(II) and Fe(0)-loaded leonardite and 1.5 g/L for raw leonardite; dye concentration: 10 ppm; solution pH: 2.0; H₂O₂ concentration: 50 µL/L; volume: 100 mL and reaction time: 60 min, RR180 dye removal efficiencies were 91%, 100%, and 100% by raw leonardite, Fe(0)-loaded leonardite and Fe(II)-loaded leonardite, respectively. The stability and reusability of the tested catalyst was investigated up to ten cycles. The experimental results revealed that both Fe(0)-loaded leonardite and Fe(II)-loaded leonardite can be used in Fenton reaction up to four cycles without decreasing their efficiency in RR180 color removal. The characterization of the catalysts was established using scanning electron microscope with energy dispersive X-ray spectroscopy (SEM-EDX). The synthesized catalyst can be used at large scale in any textile industry to effectively remove dyes resulting in high elimination rates at the optimal determined and studied conditions.

Developing a Chromatographic 99mTc Generator Based on Mesoporous Alumina for Industrial Radiotracer Applications: A Potential New Generation Sorbent for Using Low-Specific-Activity 99Mo

The commercial low-pressure column chromatographic ⁹⁹Mo/^99mTc generator represents a reliable source of onsite, ready-to-use ^99mTc for industrial applications. These generators use fission-produced ⁹⁹Mo of high specific activity, posing serious production challenges and raising proliferation concerns. Therefore, many concepts are aimed at using low-specific-activity (LSA) ⁹⁹Mo. Nonetheless, the main roadblock is the low sorption capacity of the used alumina (Al₂O₃). This study investigates the feasibility of using commercial alumina incorporated with LSA ⁹⁹Mo to develop a useful ⁹⁹Mo/^99mTc generator for industrial radiotracer applications. First, the adsorption profiles of some commercial alumina sorbents for LSA ⁹⁹Mo were tested under different experimental conditions. Then, the potential materials to develop a ⁹⁹Mo/^99mTc generator were selected and evaluated regarding elution yield of ^99mTc and purity. Among the sorbents investigated in this study, mesoporous alumina (SA-517747) presented a unique sorption-elution profile. It demonstrated a high equilibrium and dynamic sorption capacity of 148 ± 8 and 108 ± 6 mg Mo/g. Furthermore, ^99mTc was eluted with high yield and adequate chemical, radiochemical, and radionuclidic purity. Therefore, this approach provides an efficient and cost-effective way to supply onsite ^99mTc for radiotracer applications independent of fission-produced ⁹⁹Mo technology.

Recent trends and advancements in nanoporous membranes for water purification

When it comes to electrocatalysis, the creation of nanodevices, the research of energy and the environment, and diagnostics, nanoporous materials are an asset. Nanoporous membranes, which can be used to filter water, have recently been the subject of new research and are summarized in this review. These membranes are used to remove salts and metallic ions from the water following an analysis of several nanoporous membrane types and production procedures. Demonstrations and discussions of these membrane systems are then conducted. Nanoporous membranes can be used to filter water, according to the conclusions of this study, which will help readers better grasp how they work. As a result, novel water purification nanoporous compounds that are easy to manufacture, inexpensive, and effective will be developed. Merits and demerits of nanoporous membrane for water treatment and its advancements in purification were discussed.

Scale-Up of Solvent-Free, Mechanochemical Precursor Synthesis for Nanoporous Carbon Materials via Extrusion

The mechanochemical synthesis of nitrogen-rich nanoporous carbon materials has been scaled up using an extruder. Lignin, urea, and K₂ CO₃ were extruded under heat and pressure to yield nanoporous carbons with up to 3500 m²  g^-1 specific surface area after pyrolysis. The route was further broadened by applying different nitrogen sources as well as sawdust as a low-cost renewable feedstock to receive carbons with a C/N ratio of up to 15 depending on nitrogen source and extrusion parameters. The texture of obtained carbons was investigated by scanning electron microscopy as well as argon and nitrogen physisorption, while the chemical structure was analyzed by X-ray photoelectron spectroscopy. The received carbon was tested as a supercapacitor electrode, showing comparable performance to similar ball-mill-synthesized materials. Lastly, the space-time yield was applied to justify the use of a continuous reactor versus the ball mill.

Controlling oxygen vacancies of CoMn2O4 by loading on planar and tubular clay minerals and its application for boosted PMS activation

A representative transition metal oxide (TMO), CoMn₂O₄ (CMO), is recognized as an effective peroxymonosulfate (PMS) activator with disadvantages like limited reactive sites and metal leakage. Herein, novel catalysts were synthesized by anchoring CMO on kaolinite (Kln) and halloysite (Hal) matrixes, two natural clay minerals with lamellar and tubular structures, for PMS activation in pharmaceutical degradation. Hal and Kln helped to control the crystallinity of CMO spontaneously with induce oxygen vacancies (OVs), which significantly enhanced the working efficiency. The reaction rate constants of Hal/CMO and Kln/CMO towards OFX degradation were nearly triple and twice that of bare CMO, respectively, with a 60% decrease in metal usage. The formation of OVs provided additional active sites for the reaction and accelerated the electron transfer. CMO/Hal and CMO/Kln exhibited better stability and durability than CMO, while CMO/Kln showed higher structural stability with lower metal leaching after 3 rounds of reaction. The higher crystallinity of CMO/Kln resulted in less OVs, but higher structural stability. The universal applicability of CMO/Hal and CMO/Kln were verified by using three other pharmaceuticals as probes. This work shed light on the modification of TMO catalysts by introducing clay mineral substrates for the efficient and ecofriendly remediation of pharmaceuticals in wastewater.

Covalent and Non-covalent Functionalized Nanomaterials for Environmental Restoration

Nanotechnology has emerged as an extraordinary and rapidly developing discipline of science. It has remolded the fate of the whole world by providing diverse horizons in different fields. Nanomaterials are appealing because of their incredibly small size and large surface area. Apart from the naturally occurring nanomaterials, synthetic nanomaterials are being prepared on large scales with different sizes and properties. Such nanomaterials are being utilized as an innovative and green approach in multiple fields. To expand the applications and enhance the properties of the nanomaterials, their functionalization and engineering are being performed on a massive scale. The functionalization helps to add to the existing useful properties of the nanomaterials, hence broadening the scope of their utilization. A large class of covalent and non-covalent functionalized nanomaterials (FNMs) including carbons, metal oxides, quantum dots, and composites of these materials with other organic or inorganic materials are being synthesized and used for environmental remediation applications including wastewater treatment. This review summarizes recent advances in the synthesis, reporting techniques, and applications of FNMs in adsorptive and photocatalytic removal of pollutants from wastewater. Future prospects are also examined, along with suggestions for attaining massive benefits in the areas of FNMs.