Prediction of mono- and polycyclic aromatic hydrocarbon degradation in spiked soils using cyclodextrin extraction

Determining the bioavailability of benzo(a)pyrene through standardized desorption extraction in a certified reference contaminated soil

There is a strong need for certified reference materials in the quality assurance of nonionic soil contaminant bioavailability estimations through physicochemical methods. We applied desorption extraction, a method recently standardized as ISO16751, to determine the bioavailable concentration of the most commonly regulated polycyclic aromatic hydrocarbon (PAH), benzo(a)pyrene (BaP), in the reference industrial soil BCR-524 with a certified BaP total concentration of 8.60 mg kg^-1. This concentration represented BaP levels found in many PAH-polluted soils. The method, based on single-point extraction of the analyte desorbed into the aqueous phase by a receiving phase (Tenax or cyclodextrin), was applied ten times. The data fulfilled highly demanding quality criteria based on recovery and repeatability. The bioavailable BaP concentration detected through Tenax extraction, 1.82 mg kg^-1, was comparable to bioavailable concentrations determined in field-contaminated soils and to environmental quality standards based on previously observed total BaP concentrations. There was good agreement (Student's t-test, P ≤ 0.05) with the bioavailable BaP concentration determined by cyclodextrin extraction (1.53 mg kg^-1). The methods were extended to four other certified 4- and 5-ringed PAHs for comparative purposes. We suggest ways of improving of the ISO16751 standard related to further systematic assessment of the Tenax-to-soil ratio and incorporation of mass balances. Furthermore, BCR-524 is suitable for quality-assurance protocols with these methods when used in site-specific risk assessments of PAH-polluted environments.

Computational Insights Into the Influence of Substitution Groups on the Inclusion Complexation of β-Cyclodextrin

Cyclodextrins (CDs) and their derivatives have good prospects in soil remediation application due to their ability to enhance the stability and solubility of low water-soluble compounds by inclusion performance. To investigate the effect of different structural properties of cyclodextrin and its derivatives on the inclusion complexation, molecular dynamic (MD) simulations were performed on the inclusion complexes formed by three kinds of CDs with polycyclic aromatic hydrocarbons (PAHs). Based on neutral β-CD, the other two CDs were modified by introducing substitutional groups, including 2-hydroxypropyl and sulfonated butyl (SBE) functional groups in the ring structure, called HP-CD and SBE-CD. MD results show that PAH can merely enter into the cavity of SBE–β-CD from its wide rim. The substitutional groups significantly affect the structure of CDs, which may also cause the flipping of the glucose units. However, the substitutional groups can also enlarge the volume of the hydrophobic cavity, resulting in a tight combination with the guest molecules.

Effect of ageing on benzo[a]pyrene extractability in contrasting soils

Changes in benzo[a]pyrene (B[a]P) extractability over 160 days ageing in four contrasting soils varying in organic matter content and clay mineralogy were investigated using dichloromethane: acetone 1:1 (DCM/Ace), 60 mM hydroxypropyl-β-cyclodextrin (HPCD) solution, 1-butanol (BuOH) and Milli-Q water. The B[a]P extractability by the four methods decreased with ageing and a first-order exponential model could be used to describe the kinetics of release. Correlation of the kinetic rate constant with major soil properties showed a significant effect of clay and sand contents and pore volume fraction (<6 nm) on sequestration of the desorbable fraction (by HPCD) and the water-extractable fraction. Analysis of (14)C-B[a]P in soils after ageing showed a limited loss of B[a]P via degradation. Fractionation of B[a]P pools associated with the soil matrix was analysed according to extractability of B[a]P by the different extraction methods. A summary of the different fractions is proposed for the illustration of the effect of ageing on different B[a]P-bound fractions in soils. This study provides a better understanding of the B[a]P ageing process associated with different fractions and also emphasises the extraction capacity of the different methods employed.

From Bioavailability Science to Regulation of Organic Chemicals

The bioavailability of organic chemicals in soil and sediment is an important area of scientific investigation for environmental scientists, although this area of study remains only partially recognized by regulators and industries working in the environmental sector. Regulators have recently started to consider bioavailability within retrospective risk assessment frameworks for organic chemicals; by doing so, realistic decision-making with regard to polluted environments can be achieved, rather than relying on the traditional approach of using total-extractable concentrations. However, implementation remains difficult because scientific developments on bioavailability are not always translated into ready-to-use approaches for regulators. Similarly, bioavailability remains largely unexplored within prospective regulatory frameworks that address the approval and regulation of organic chemicals. This article discusses bioavailability concepts and methods, as well as possible pathways for the implementation of bioavailability into risk assessment and regulation; in addition, this article offers a simple, pragmatic and justifiable approach for use within retrospective and prospective risk assessment.

The impact of biochar on the bioaccessibility of (14)C-phenanthrene in aged soil

Biochar is a carbon rich product from the incomplete combustion of biomass and it has been shown to reduce bioavailability of organic contaminants through adsorption. This study investigated the influence of 0%, 1%, 5% and 10% of two different particle sized wood biochars (≤2 mm and 3-7 mm) on the bioaccessibility of (14)C-phenanthrene (10 mg kg(-1)) in aged soil. The extent of (14)C-phenanthrene mineralisation by phenanthrene-degrading Pseudomonas sp. inoculum was monitored over a 14 day period in respirometric assays and compared to hydroxypropyl-β-cyclodextrin (HPCD) aqueous extraction. Notably, biochar amendments showed significant reduction in extents of mineralisation and HPCD extraction. Linear correlations between HPCD extractability and the total amount mineralised revealed good correlations, with 2 mm biochar showing a best fit (r(2) = 0.97, slope = 1.11, intercept = 1.72). Biochar reduced HPCD extractability and bioaccessibility of (14)C-phenanthrene to microorganisms in a similar manner. Biochar can aid risk reduction to phenanthrene exposure to biota in soil and HPCD can serve as a useful tool to assess the extent of exposure in biochar-amended soils.

Using chemical desorption of PAHs from sediment to model biodegradation during bioavailability assessment

This work compares the biodegradation potential of four polycyclic aromatic hydrocarbons (PAH) (phenanthrene, pyrene, chrysene and benzo(a)pyrene, chosen as representatives of the 3, 4 and 5 ring PAHs) with their desorption from sediment by XAD4 resin and methyl-β-cyclodextrin (MCD). The biodegradation study was conducted under various conditions (biostimulation, bioaugmentation and their combination). The results show that total PAH removal in all treatments except biostimulation gave similar results, whereby the total amount of PAHs was decreased by about 30-35%. The desorption experiment showed that XAD4 desorbed a greater fraction of phenanthrene (77% versus 52%), and benzo(a)pyrene (44% versus 25%) than MCD. The results for four ring PAHs were similar for both desorption agents (about 30%). Comparing the maximum biodegraded amount of each PAH with the rapidly desorbed XAD4 and MCD fraction, XAD4 was found to correlate better with biodegradation for the high molecular PAHs (pyrene, chrysene, benzo(a)pyrene), although it overestimated the availability of phenanthrene. In contrast, MCD showed better correlation with the biodegradation of low molecular weight PAHs.

The effects of sewage sludge and sewage sludge biochar on PAHs and potentially toxic element bioaccumulation in Cucumis sativa L

The presence of contaminants such as polycyclic aromatic hydrocarbons (PAHs) and potentially toxic elements (PTEs), including As, Cd, Cu, Pb and Zn, restricts the application of sewage sludge (SS) to agricultural land. This research established that the conversion of SS to SS biochar (SSBC) significantly (p ≤ 0.01) decreased PAH and available PTE concentrations. Once added to soil both SS and SSBC significantly (p ≤ 0.05) decrease PAH availability. Bioaccumulation of PAHs into Cucumis sativa L. was reduced by both SSBC (44-57%) and (to a lesser extent 20-36%) by SS. Following addition to soil SSBC significantly (p ≤ 0.05) reduced available PTEs (except Cd), while SS significantly (p ≤ 0.05) increased PTE availability. As a consequence SSBC significantly (p ≤ 0.05) reduced PTE bioaccumulation (except Cd and Zn), while SS increased PTE bioaccumulation. These results suggest SSBC to be a candidate for soil amendment that offers advantages over SS in terms of PAH/PTE bioaccumulation mitigation.

Hydroxypropyl-β-cyclodextrin extractability and bioavailability of phenanthrene in humin and humic acid fractions from different soils and sediments

Organic matter (OM) plays a vital role in controlling polycyclic aromatic hydrocarbon (PAH) bioavailability in soils and sediments. In this study, both a hydroxypropyl-β-cyclodextrin (HPCD) extraction test and a biodegradation test were performed to evaluate the bioavailability of phenanthrene in seven different bulk soil/sediment samples and two OM components (humin fractions and humic acid (HA) fractions) separated from these soils/sediments. Results showed that both the extent of HPCD-extractable phenanthrene and the extent of biodegradable phenanthrene in humin fraction were lower than those in the respective HA fraction and source soil/sediment, demonstrating the limited bioavailability of phenanthrene in the humin fraction. For the source soils/sediments and the humin fractions, significant inverse relationships were observed between the sorption capacities for phenanthrene and the amounts of HPCD-extractable or biodegradable phenanthrene (p < 0.05), suggesting the importance of the sorption capacity in affecting desorption and biodegradation of phenanthrene. Strong linear relationships were observed between the amount of HPCD-extractable phenanthrene and the amount degraded in both the bulk soils/sediments and the humin fractions, with both slopes close to 1. On the other hand, in the case of phenanthrene contained in HA, a poor relationship was observed between the amount of phenanthrene extracted by HPCD and the amount degraded, with the former being much less than the latter. The results revealed the importance of humin fraction in affecting the bioavailability of phenanthrene in the bulk soils/sediments, which would deepen our understanding of the organic matter fractions in affecting desorption and biodegradation of organic pollutants and provide theoretical support for remediation and risk assessment of contaminated soils and sediments.

The prediction of PAHs bioavailability in soils using chemical methods: state of the art and future challenges

The evaluation of the available fraction of hydrophobic organic contaminants (HOCs) is extremely important for assessing their risk to the environment and human health. This available fraction, which can be solubilized and/or easily extracted, is believed to be the most accessible for bioaccumulation, biosorption and/or transformation by organisms. Based on this, two main types of chemical methods have been developed, closely related to the concepts of bioaccessibility and freely available concentrations: non-exhaustive extractions and biomimetic methods. Since bioavailability is species and compound specific, this work focused only in one of the most widespread group of HOCs in soils: polycyclic aromatic hydrocarbons (PAHs). This study aims at producing a state of the art knowledge base on bioavailability and chemical availability of PAHs in soils, clarifying which chemical methods can provide a better prediction of an organism exposure, and which are the most promising ones. Therefore, a review of the processes involved on PAHs availability to microorganisms, earthworms and plants was performed and the outputs given by the different chemical methods were evaluated. The suitability of chemical methods to predict bioavailability of the 16 US EPA PAHs in dissimilar naturally contaminated soils was not yet demonstrated, being especially difficult for high molecular weight compounds. Even though the potential to predict microbial mineralization using non-exhaustive extractions is promising, it will be very difficult to achieve for earthworms and plants, due to the complexity of accumulation mechanisms which are not taken into account by chemical methods. Yet, the existing models could be improved by determining compound, species and site specific parameters. Moreover, chemical availability can be very useful to understand the bioavailability processes and the behavior of PAHs in soils. The inclusion of chemical methods on risk assessment has been suggested and it is promising, despite some methods overpredict risks.

Tenax extraction for exploring rate-limiting factors in methyl-β-cyclodextrin enhanced anaerobic biodegradation of PAHs under denitrifying conditions in a red paddy soil

The effectiveness of anaerobic bioremediation systems for PAH-contaminated soil may be constrained by low contaminants bioaccessibility due to limited aqueous solubility and lack of suitable electron acceptors. Information on what is the rate-limiting factor in bioremediation process is of vital importance in the decision in what measures can be taken to assist the biodegradation efficacy. In the present study, four different microcosms were set to study the effect of methyl-β-cyclodextrin (MCD) and nitrate addition (N) on PAHs biodegradation under anaerobic conditions in a red paddy soil. Meanwhile, sequential Tenax extraction combined with a first-three-compartment model was employed to evaluate the rate-limiting factors in MCD enhanced anaerobic biodegradation of PAHs. Microcosms with both 1% (w/w) MCD and 20mM N addition produced maximum biodegradation of total PAHs of up to 61.7%. It appears rate-limiting factors vary with microcosms: low activity of degrading microorganisms is the vital rate-limiting factor for control and MCD addition treatments (CK and M treatments); and lack of bioaccessible PAHs is the main rate-limiting factor for nitrate addition treatments (N and MN treatments). These results have practical implications for site risk assessment and cleanup strategies.

Chemical measures of bioavailability/bioaccessibility of PAHs in soil: fundamentals to application

Risk assessment and remediation of contaminated land is inherently dependent on the contaminants present and their availability for interaction with soil biota. An ever-growing body of evidence suggests that current regulatory procedures over-estimate the 'true' fraction available to biota. Thus, a procedure that predicts the 'bioavailable fraction' would be useful for predicting 'actual' exposure limits and provide a more relevant basis for risk assessment. The aim of this paper is to address several important questions: "How should bioavailability be defined?" "What factors affect bioavailability measurement?" "To what extent have existing protocols measured bioavailability?" "What is actually measured by chemical techniques purported to determine bioavailability?" We offer two definitions (namely 'bioavailability' and 'bioaccessibility') and review commonly employed chemical extraction techniques to measure putative bioavailability. Relative advantages and disadvantages of the techniques are highlighted to elucidate underlying factors for the wide range of conclusions observed in the literature. Although the concept of bioavailability is implicit to contaminated land risk assessment and remediation, explicit reference to and use of adjustment factors is rare amongst regulatory bodies and remediators. Use of chemical determinants for bioavailability, applicable within current legislation and due consideration to inherent variability, are proposed and barriers to their implementation discussed.

Impact of black carbon on the bioaccessibility of organic contaminants in soil

The ability of carbonaceous geosorbents (CGs) such as black carbon (BC) to extensively sorb many common environmental contaminants suggests that they potentially possesses qualities useful to the sequestration of harmful xenobiotics within contaminated land. Presently, however, there is limited understanding of the implications for the bioaccessibility, mobility and environmental risk of organic contaminants while sorbed to BC in soil and sediment, in addition to the inherent toxicity of BC itself to terrestrial flora and fauna. We review both the processes involved in and factors influencing BC sorption characteristics, and ultimately consider the impacts BC will have for bioavailability/bioaccessibility, toxicity and risk assessment/remediation of contaminated land. We conclude that while the application of BC is promising, additional work on both their toxicity effects and long-term stability is required before their full potential as a remediation agent can be safely exploited.

Experimental increase in availability of a PAH complex organic contamination from an aged contaminated soil: consequences on biodegradation

Although high PAH content and detection of PAH-degraders, the PAH biodegradation is limited in aged-contaminated soils due to low PAH availability (i.e., 1%). Here, we tried to experimentally increase the soil PAH availability by keeping both soil properties and contamination composition. Organic extract was first removed and then re-incorporated in the raw soil as fresh contaminants. Though drastic, this procedure only allowed a 6-time increase in the PAH availability suggesting that the organic constituents more than ageing were responsible for low availability. In the re-contaminated soil, the mineralization rate was twice more important, the proportion of 5-6 cycles PAH was higher indicating a preferential degradation of lower molecular weight PAH. The extraction treatment induced bacterial and fungal community structures modifications, Pseudomonas and Fusarium solani species were favoured, and the relative quantity of fungi increased. In re-contaminated soil the percentage of PAH-dioxygenase gene increased, with 10 times more Gram negative representatives.

Remediation of polycyclic aromatic hydrocarbon and metal-contaminated soil by successive methyl-β-cyclodextrin-enhanced soil washing-microbial augmentation: a laboratory evaluation

Polycyclic aromatic hydrocarbon (PAH) and metal-polluted sites caused by abandoned coking plants are receiving wide attention. To address the associated environmental concerns, innovative remediation technologies are urgently needed. This study was initiated to investigate the feasibility of a cleanup strategy that employed an initial phase, using methyl-β-cyclodextrin (MCD) solution to enhance ex situ soil washing for extracting PAHs and metals simultaneously, followed by the addition of PAH-degrading bacteria (Paracoccus sp. strain HPD-2) and supplemental nutrients to treat the residual soil-bound PAHs. Elevated temperature (50 °C) in combination with ultrasonication (35 kHz, 30 min) at 100 g MCD L(-1) was effective in extracting PAHs and metals to assist soil washing; 93 % of total PAHs, 72 % of Cd, 78 % of Ni, 93 % of Zn, 84 % of Cr, and 68 % of Pb were removed from soil after three successive washing cycles. Treating the residual soil-bound PAHs for 20 weeks led to maximum biodegradation rates of 34, 45, 36, and 32 % of the remaining total PAHs, 3-ring PAHs, 4-ring PAHs, and 5(+6)-ring PAHs after washing procedure, respectively. Based on BIOLOG Ecoplate assay, the combined treatment at least partially restored microbiological functions in the contaminated soil. The ex situ cleanup strategy through MCD-enhanced soil washing followed by microbial augmentation can be effective in remediating PAH and metal-contaminated soil.

Influence of activated charcoal on desorption kinetics and biodegradation of phenanthrene in soil

The observed strong sorption of polycyclic aromatic hydrocarbons (PAHs) to black carbon (BC) presents potential implications for PAH bioaccessibility in soils. The effects of BC on the desorption kinetics and mineralization of phenanthrene in four soils was investigated after 1, 25, 50, and 100 d soil-PAH contact time, using sequential hydroxypropyl-β-cyclodextrin (HPCD) extractions in soils amended with 0, 0.1, 1, and 5% (dry wt. soil) activated charcoal (AC, a form of BC). The rapidly (%F(rap)) and slowly (%F(slow)) desorbing phenanthrene fractions and their rate constants were determined using a first-order two-compartment (biphasic) desorption model. A minimum 7.8-fold decrease in %F(rap) occurred when AC was increased from 0 to 5%, with a corresponding increase in %F(slow). Desorption rate constants followed the progression k(rap) (% h(-1)) > k(slow) (% h(-1)) and were in the order of 10(-1) to 10(-2) and 10(-3) to 10(-4), respectively. Linear regressions between %F(rap) and the fractions degraded by a phenanthrene-degrading inoculum (%F(min)) indicated that slopes did not approximate 1 at concentrations greater than 0% AC; %F(min) often exceeded %F(rap), indicating a fraction of sorbed phenanthrene (%F(slow)) remained microbially accessible. Therefore, HPCD-desorption kinetics alone may not be an adequate basis for the prediction of the bioaccessibility of PAHs to microorganisms or bioremediation potential in AC-amended soils.

Mechanistic insights into the role of river sediment in the attenuation of the herbicide isoproturon

Mechanistic insights into the relative contribution of sorption and biodegradation on the removal of the herbicide isoproturon (IPU) are reported. (14)C-radiorespirometry indicated very low levels of catabolic activity in IPU-undosed and IPU-dosed (0.1, 1, 100 μg L(-1)) river water (RW) and groundwater (GW) (mineralisation: <2%). In contrast, levels of catabolic activity in IPU-undosed and IPU-dosed river sediment (RS) were significantly higher (mineralisation: 14.5-36.9%). Levels of IPU catabolic competence showed a positive log-linear relationship (r(2) = 0.768) with IPU concentration present. A threshold IPU concentration of between 0.1 μg L(-1) and 1 μg L(-1) was required to significantly (p < 0.05) increase levels of catabolic activity. Given the EU Drinking Water Directive limit for a single pesticide in drinking water of <0.1 μg L(-1) this result suggests that riverbed sediment infiltration is potentially an appropriate 'natural' means of improving water quality in terms of pesticide levels at concentrations that are in keeping with regulatory limits.

The effects of aging time on the fraction distribution and bioavailability of PAH

Understanding the effects of aging time on the fraction distribution and bioavailability of PAH, such as phenanthrene (PHE) and pyrene (PYR), has considerable benefits for risk assessment, food security and remediation strategies for contaminated soil. The results of the present study show that the proportion of the desorbed PHE decreased from ca. 82% at day 0 to ca. 65% at day 150. In addition, non-desorbed PHE increased from ca. 18% at day 0 to ca. 31% at day 150, whereas the changes of desorbed and non-desorbed PYR showed no significant trend during this aging period. The proportion of desorbed PYR was lower than that of PHE, whereas the opposite occurred with the non-desorbed fraction. After 150 d of aging, the proportion of bound residues (PHE and PYR) increased significantly with the cultivating time from ca. 0.2% to ca. 4.7% and ca. 0.1% to ca. 1.2% for PHE and PYR, respectively. In addition, the bioavailability of PAH (PHE and PYR) to earthworms was also assessed over 0-150 d. The results showed that the uptake rate and bioconcentration factor (BCF) of pollutants by earthworms displayed the following biphasic character: a rapid decrease over the first 15 d followed by a slow decrease over the next 135 d. Moreover, the earthworm uptake rate of PHE was greater than that of PYR throughout the incubation period, indicating that PHE has a higher bioavailability than PYR. In addition, the positive correlation between the uptake rate of earthworms and PAH extractability suggested that a three-step extraction is a reliable approach to predict PHE bioavailability in soil. However, a limit was observed for PYR.

Assessment of phenanthrene bioavailability in aged and unaged soils by mild extraction

It has become apparent that the threat of an organic pollutant in soil is directly related to its bioavailable fraction and that the use of total contaminant concentrations as a measure of potential contaminant exposure to plants or soil organisms is inappropriate. In light of this, non-exhaustive extraction techniques are being investigated to assess their appropriateness in determining bioavailability. To find a suitable and rapid extraction method to predict phenanthrene bioavailability, multiple extraction techniques (i.e., mild hydroxypropyl-β-cyclodextrin (HPCD) and organic solvents extraction) were investigated in soil spiked to a range of phenanthrene levels (i.e., 1.12, 8.52, 73, 136, and 335 μg g( - 1) dry soil). The bioaccumulation of phenanthrene in earthworm (Eisenia fetida) was used as the reference system for bioavailability. Correlation results for phenanthrene suggested that mild HPCD extraction was a better method to predict bioavailability of phenanthrene in soil compared with organic solvents extraction. Aged (i.e., 150 days) and fresh (i.e., 0 day) soil samples were used to evaluate the extraction efficiency and the effect of soil contact time on the availability of phenanthrene. The percentage of phenanthrene accumulated by earthworms and percent recoveries by mild extractants changed significantly with aging time. Thus, aging significantly reduced the earthworm uptake and chemical extractability of phenanthrene. In general, among organic extractants, methanol showed recoveries comparable to those of mild HPCD for both aged and unaged soil matrices. Hence, this extractant can be suitable after HPCD to evaluate risk of contaminated soils.

Methyl-beta-cyclodextrin enhanced biodegradation of polycyclic aromatic hydrocarbons and associated microbial activity in contaminated soil

The contamination of soils by polycyclic aromatic hydrocarbons (PAHs) is a widespread environmental problem and the remediation of PAHs from these areas has been a major concern. The effectiveness of many in situ bioremediation systems may be constrained by low contaminant bioavailability due to limited aqueous solubility or a large magnitude of sorption. The objective of this research was to evaluate the effect of methyl-beta-cyclodextrin (MCD) on bioaugmentation by Paracoccus sp. strain HPD-2 of an aged PAH-contaminated soil. When 10% (W/W) MCD amendment was combined with bioaugmentation by the PAH-degrading bacterium Paracoccus sp. strain HPD-2, the percentage degradation of total PAHs was significantly enhanced up to 34.8%. Higher counts of culturable PAH-degrading bacteria and higher soil dehydrogenase and soil polyphenol oxidase activities were observed in 10% (W/W) MCD-assisted bioaugmentation soil. This MCD-assisted bioaugmentation strategy showed significant increases (p < 0.05) in the average well color development (AWCD) obtained by the BIOLOG Eco plate assay, Shannon-Weaver index (H) and Simpson index (lambda) compared with the controls, implying that this strategy at least partially restored the microbiological functioning of the PAH-contaminated soil. The results suggest that MCD-aided bioaugmentation by Paracoccus sp. strain HPD-2 may be a promising practical bioremediation strategy for aged PAH-contaminated soils.

Aging of organochlorine pesticides and polychlorinated biphenyls in muck soil: volatilization, bioaccessibility, and degradation

An organic rich muck soil which is highly contaminated with native organochlorine pesticide (OCs) was spiked with known amounts of (13)C-labeled OCs and nonlabeled polychlorinated biphenyls (PCBs). Spiked soils were aged under indoor, outdoor, and sterile conditions and the change in volatility, surrogate bioaccessibility, and degradation of chemicals was monitored periodically over 730 d. Volatility was measured using a fugacity meter to characterize the soil-air partition coefficient (K(SA) = C(SOIL)/C(AIR)). The fraction of bioaccessible residues was estimated by comparing recoveries of chemical with a mild extractant, hydroxylpropyl-β-cyclodextrin (HPCD) vs a harsh extractant, DCM. K(SA) of the spiked OCs in the nonsterile (Indoor, Outdoor) soils were initially lower and approached the K(SA) of native OCs over time, showing reduction of volatility upon aging. HPCD extractability of spiked OCs and PCBs were negatively correlated with K(SA), which suggests that volatility can be used as a surrogate for bioaccessibility. Degradation of endosulfans, PCB 8 and 28 was observed in the nonsterile soils, and (13)C(6)-α-HCH showed selective degradation of the (+) enantiomer. Enantiomer fractions (EF) in air and HPCD extracts were lower than in nonsterile soils, suggesting greater sequestering of the (+) enantiomer in the soil during microbial degradation.

Assessment of pyrene bioavailability in soil by mild hydroxypropyl-β-cyclodextrin extraction

Bioavailability of organic pollutants in soil is currently a much-debated issue in risk assessment of contaminated sites. Ecorisk of an organic pollutant in soil is strongly influenced by the properties of the soil and its contamination history. To evaluate the effect of aging on the availability of pyrene, earthworm (Eisenia fetida) accumulation and chemical extraction by exhaustive and nonexhaustive techniques in soil spiked with a range of pyrene levels (1.07, 9.72, 88.4, 152, and 429 μg g⁻¹ dry soil) were measured in this study using both unaged (i.e., 0 days) and aged (i.e., 69, 150, and 222 days) soil samples. The results showed that the amount of pyrene accumulated by earthworms did not change greatly with aging time under different high-dose contamination levels, but changed significantly at lower concentrations. Moreover, aging (after 222 days) significantly decreased biological and chemical availability of pyrene. Furthermore, the relationship between earthworm bioaccumulation, hydroxypropyl-β-cyclodextrin (HPCD), and organic solvent extraction was investigated in order to find a suitable and rapid method to predict pyrene bioavailability. Results showed that, at different levels of pyrene, the mean values of earthworm uptake and HPCD extractability were 10-40% and 10-65%, respectively. Correlation (r² = 0.985) and extraction results for pyrene suggested that mild HPCD extraction was a better method to predict bioavailability of pyrene in soil compared with organic solvent extraction.

Assessment of five bioaccessibility assays for predicting the efficacy of petroleum hydrocarbon biodegradation in aged contaminated soils

In this study, the bioaccessibility of petroleum hydrocarbons in aged contaminated soils (1.6-67gkg(-1)) was assessed using four non-exhaustive extraction techniques (100% 1-butanol, 100% 1-propanol, 50% 1-propanol in water and hydroxypropyl-β-cyclodextrin) and the persulfate oxidation method. Using linear regression analysis, residual hydrocarbon concentrations following bioaccessibility assessment were compared to residual hydrocarbon concentrations following biodegradation in laboratory-scale microcosms in order to determine whether bioaccessibility assays can predict the endpoint of hydrocarbon biodegradation. The relationship between residual hydrocarbon concentrations following microcosm biodegradation and bioaccessibility assessment was linear (r(2)=0.71-0.97) indicating that bioaccessibility assays have the potential to predict the extent of hydrocarbon biodegradation. However, the slope of best fit varied depending on the hydrocarbon fractional range assessed. For the C(10)-C(14) hydrocarbon fraction, the slope of best fit ranged from 0.12 to 0.27 indicating that the non-exhaustive or persulfate oxidation methods removed 3.5-8 times more hydrocarbons than biodegradation. Conversely, for the higher molecular weight hydrocarbon fractions (C(29)-C(36) and C(37)-C(40)), biodegradation removed up to 3.3 times more hydrocarbons compared to bioaccessibility assays with the resulting slope of best fit ranging from 1.0-1.9 to 2.0-3.3 respectively. For mid-range hydrocarbons (C(15)-C(28)), a slope of approximately one was obtained indicating that C(15)-C(28) hydrocarbon removal by these bioaccessibility assays may approximate the extent of biodegradation. While this study demonstrates the potential of predicting biodegradation endpoints using bioaccessibility assays, limitations of the study include a small data set and that all soils were collected from a single site, presumably resulting from a single contamination source. Further evaluation and validation is required using soils from a range of hydrocarbon contamination sources in order to develop robust assays for predicting bioremediation endpoints in the field.

Linking desorption kinetics to phenanthrene biodegradation in soil

The desorption of polycyclic aromatic hydrocarbons (PAHs) often exhibits a biphasic profile similar to that observed for biodegradation whereby an initial rapid phase of degradation or desorption is followed by a phase of much slower transformation or release. Most investigations to-date have utilised a polymeric sorbent, such as Tenax, to characterise desorption, which is methodologically unsuitable for the analysis of soil. In this study, desorption kinetics of (14)C-phenanthrene were measured by consecutive extraction using aqueous solutions of hydroxypropyl-beta-cyclodextrin (HPCD). The data indicate that the fraction extracted after 24 h generally approximated the linearly sorbed, rapidly desorbing fraction (F(rap)), calculated using a three-compartment model. A good linear correlation between phenanthrene mineralised and F(rap) was observed (r(2) = 0.89; gradient = 0.85; intercept = 8.20). Hence HPCD extraction (24 h) and first-order three-compartment modelling appear to provide an operationally straightforward tool for estimating mass-transfer limited biodegradation in soil.

Hydroxypropyl-beta-cyclodextrin as non-exhaustive extractant for organochlorine pesticides and polychlorinated biphenyls in muck soil

Hydroxypropyl-beta-cyclodextrin (HPCD) was used as a non-exhaustive extractant for organochlorine pesticides (OCs) and polychlorinated biphenyls (PCBs) in muck soil. An optimized extraction method was developed which involved using a HPCD to soil mass ratio of 5.8 with a single extraction period of 20 h. An aging experiment was performed by spiking a muck soil with (13)C-labeled OCs and non-labeled PCBs. The soil was extracted with the optimized HPCD method and Soxhlet apparatus with dichloromethane over 550 d periodically. The HPCD extractability of the spiked OCs was greater than of the native OCs. A decreased in HPCD extractability was observed for the spiked OCs after 550 d of aging and their extractability approached those of the natives. The partition coefficient between HPCD and soil (logK(CD-Soil)) was negatively correlated with the octanol-water partition coefficient (logK(OW)) with r(2)=0.67 and p<0.05.

Sequential extraction of polycyclic aromatic hydrocarbons using subcritical water

A rapid sequential subcritical (superheated) water extraction method for polycyclic aromatic hydrocarbons (PAHs) in contaminated soil and sediment is presented. Decreasing the polarity of water by successive increase of the extraction temperature from 50 degrees C to 200 degrees C at the moderate pressure (10.3MPa) enabled selective, non-exhaustive extractions to be performed. Concurrent with increasing temperatures to 150 degrees C there was an increase in PAH extraction efficiencies. For the majority of determinations no significant differences between extractions at 150 degrees C and 200 degrees C were observed. Varied extraction efficiencies of PAHs at the same extraction conditions reflected dissimilarities between environmental matrices investigated. Selective subcritical water extraction of PAHs was proportional to their octanol-water partition coefficients. This technique may be applicable in evaluation of risks associated with PAH contaminated sites and in assessments of their bioremediation potential.

Bioavailability of xenobiotics in the soil environment

It is often presumed that all chemicals in soil are available to microorganisms, plant roots, and soil fauna via dermal exposure. Subsequent bioaccumulation through the food chain may then result in exposure to higher organisms. Using the presumption of total availability, national governments reduce environmental threshold levels of regulated chemicals by increasing guideline safety margins. However, evidence shows that chemical residues in the soil environment are not always bioavailable. Hence, actual chemical exposure levels of biota are much less than concentrations present in soil would suggest. Because "bioavailability" conveys meaning that combines implications of chemical sol persistency, efficacy, and toxicity, insights on the magnitude of a chemicals soil bioavailability is valuable. however, soil bioavailability of chemicals is a complex topic, and is affected by chemical properties, soil properties, species exposed, climate, and interaction processes. In this review, the state-of-art scientific basis for bioavailability is addressed. Key points covered include: definition, factors affecting bioavailability, equations governing key transport and distributive kinetics, and primary methods for estimating bioavailability. Primary transport mechanisms in living organisms, critical to an understanding of bioavailability, also presage the review. Transport of lipophilic chemicals occurs mainly by passive diffusion for all microorganisms, plants, and soil fauna. Therefore, the distribution of a chemical between organisms and soil (bioavailable proportion) follows partition equilibrium theory. However, a chemical's bioavailability does not always follow partition equilibrium theory because of other interactions with soil, such as soil sorption, hysteretic desorption, effects of surfactants in pore water, formation of "bound residue", etc. Bioassays for estimating chemical bioavailability have been introduced with several targeted endpoints: microbial degradation, uptake by higher plants and soil fauna, and toxicity to organisms. However, there bioassays are often time consuming and laborious. Thus, mild extraction methods have been employed to estimate bioavailability of chemicals. Mild methods include sequential extraction using alcohols, hexane/water, supercritical fluids (carbon dioxide), aqueous hydroxypropyl-beta-cyclodextrin extraction, polymeric TENAX beads extraction, and poly(dimethylsiloxane)-coated solid-phase microextraction. It should be noted that mild extraction methods may predict bioavailability at the moment when measurements are carried out, but not the changes in bioavailability that may occur over time. Simulation models are needed to estimate better bioavailability as a function of exposure time. In the past, models have progressed significantly by addressing each group of organisms separately: microbial degradation, plant uptake via evapotranspiration processes, and uptake of soil fauna in their habitat. This approach has been used primarily because of wide differences in the physiology and behaviors of such disparate organisms. However, improvement of models is badly needed, Particularly to describe uptake processes by plant and animals that impinge on bioavailability. Although models are required to describe all important factors that may affect chemical bioavailability to individual organisms over time (e.g., sorption/desorption to soil/sediment, volatilization, dissolution, aging, "bound residue" formation, biodegradation, etc.), these models should be simplified, when possible, to limit the number of parameters to the practical minimum. Although significant scientific progress has been made in understanding the complexities in specific methodologies dedicated to determining bioavailability, no method has yet emerged to characterized bioavailability across a wide range of chemicals, organisms, and soils/sediments. The primary aim in studying bioavailability is to define options for addressing bioremediation or environmental toxicity (risk assessment), and that is unlikely to change. Because of its importance in estimating research is needed to more comprehensively address the key environmental issue of "bioavailability of chemicals in soil/sediment."

Measurement of bioaccessibility of organic pollutants in soil

The quantification of organic contaminant bioaccessibility in soils and sediments is essential for the risk assessment and remediation of contaminated land. Within this framework, practitioners require standardised protocols. Cyclodextrins are a group of macrocyclic compounds that can form inclusion complexes with organic xenobiotics. This occurrence can be exploited to measure the labile/rapidly desorbable compound fraction, which correlates with microbial degradation. We present a rapid and easily reproducible HPCD shake extraction technique that has been experimentally demonstrated to directly predict microbial availability and degradation in soil. This method can provide practitioners with both an indication of bioremediation end-points and may be valuable in the risk assessment of contaminated land.

Relative proportions of polycyclic aromatic hydrocarbons differ between accumulation bioassays and chemical methods to predict bioavailability

Chemical methods to predict the bioavailable fraction of organic contaminants are usually validated in the literature by comparison with established bioassays. A soil spiked with polycyclic aromatic hydrocarbons (PAHs) was aged over six months and subjected to butanol, cyclodextrin and tenax extractions as well as an exhaustive extraction to determine total PAH concentrations at several time points. Earthworm (Eisenia fetida) and rye grass root (Lolium multiflorum) accumulation bioassays were conducted in parallel. Butanol extractions gave the best relationship with earthworm accumulation (r(2) < or = 0.54, p < or = 0.01); cyclodextrin, butanol and acetone-hexane extractions all gave good predictions of accumulation in rye grass roots (r(2) < or = 0.86, p < or = 0.01). However, the profile of the PAHs extracted by the different chemical methods was significantly different (p < 0.01) to that accumulated in the organisms. Biota accumulated a higher proportion of the heavier 4-ringed PAHs. It is concluded that bioaccumulation is a complex process that cannot be predicted by measuring the bioavailable fraction alone.

Influence of hydroxypropyl-beta-cyclodextrin on the biodegradation of 14C-phenanthrene and 14C-hexadecane in soil

Soil was spiked with [9-(14)C]phenanthrene and [1-(14)C]hexadecane at 50 mg kg(-1) and aged for 1, 25, 50, 100 and 250 d. At each time point, the microcosms were amended with aqueous solutions of cyclodextrin (HP-beta-CD) at a range of concentrations (0-40 mM). Mineralisation assays and aqueous HP-beta-CD extractions were performed to assess the effect of the amendments on microbial degradation. The results showed that amendments had no significant impact on the microbial degradation of either of the (14)C-contaminants. Further, HP-beta-CD extractions were correlated with the mineralisation of the target chemicals in each of the soil conditions. It was found that the HP-beta-CD extraction was able to predict mineralisation in soils which had not been amended with cyclodextrin; however, in the soils containing the HP-beta-CD, there was no predictive relationship. Under the conditions of this study, the introduction of HP-beta-CD into soils did not enhance the biodegradation of the organic contaminants.

Application of a luminescence-based biosensor for assessing naphthalene biodegradation in soils from a manufactured gas plant

Despite numerous reviews suggesting that microbial biosensors could be used in many environmental applications, in reality they have failed to be used for which they were designed. In part this is because most of these sensors perform in an aqueous phase and a buffered medium, which is in contrast to the nature of genuine environmental systems. In this study, a range of non-exhaustive extraction techniques (NEETs) were assessed for (i) compatibility with a naphthalene responsive biosensor and (ii) correlation with naphthalene biodegradation. The NEETs removed a portion of the total soil naphthalene in the order of methanol > HPCD > betaCD > water. To place the biosensor performance to NEETs in context, a biodegradation experiment was carried out using historically contaminated soils. By coupling the HPCD extraction with the biosensor, it was possible to assess the fraction of the naphthalene capable of undergoing microbial degradation in soil.

Compatibility of hydroxypropyl-beta-cyclodextrin with algal toxicity bioassays

Numerous reports have indicated that hydrophobic organic compound bioaccessibility in sediment and soil can be determined by extraction using aqueous hydroxypropyl-beta-cyclodextrin (HPCD) solutions. This study establishes the compatibility of HPCD with Selenastrum capricornutum and assesses whether its presence influences the toxicity of reference toxicants. Algal growth inhibition (72 h) showed no significant (P>0.05) difference at HPCD concentrations up to and including 20 mM. HPCD presence did not influence the toxicity of the inorganic reference toxicant (ZnSO(4)), with IC50 values of 0.82 microM and 0.85 microM, in the presence and absence of HPCD (20 mM), respectively. However, HPCD presence (20 mM) reduced the toxicity of 2,4-dichlorophenol and the herbicides diuron and isoproturon. These reductions were attributed to inclusion complex formation between the toxicants and the HPCD cavity. Liberation of complexed toxicants, by sample manipulation prior to toxicity assessment, is proposed to provide a sensitive, high throughput, bioassay that reflects compound bioaccessibility.

Predicting the biodegradation of target hydrocarbons in the presence of mixed contaminants in soil

The aim of this study was to investigate the prediction of (14)C-phenanthrene and (14)C-hexadecane biodegradation in the presence of other hydrocarbons in soil using beta- and alpha-cyclodextrin (CD) solutions, respectively. Prediction of the biodegradation of (14)C-phenanthrene using the beta-CD extraction was robust under single, co-contaminant and multiple contaminant conditions (r(2)=0.92, slope of best fit line=0.87, intercept=7.24, n=84). Prediction of (14)C-hexadecane using the alpha-CD extraction was robust under single and co-contaminant conditions (r(2)=0.92, slope of best fit line=0.97, intercept=1.24, n=60); however, the alpha-CD could not accurately predict (14)C-hexadecane biodegradation in the presence of multiple contaminants. The presence of multiple contaminants enhanced (14)C-hexadecane mineralisation, but did not enhance extractability. The results from this study provide further evidence for the application of HPCD extractions for the measurement of microbial accessibility in soil.

Assessing biodegradation potential of PAHs in complex multi-contaminant matrices

This study sought to extend validation of a cyclodextrin based extraction method for the assessment of PAH-biodegradation potential to complex multi-contaminant matrices. To this end, four reference materials (RMs) were produced by blending, in different proportions, soils impacted with diesel, lubricating oil and spent oxide. These reference materials had modest summation operatorPAH (16 US EPA) concentrations that ranged from 5.6+/-0.5 to 44.4+/-4.5 mg kg(-1). However, extractable petroleum hydrocarbon (EPH) concentrations were comparatively high (up to 2520+/-204 mg kg(-1)). To complement these RMs, two further soils from a municipal gas plant (MGP) with highly elevated concentration of PAHs ranging from 877+/-52 to 2620+/-344 mg kg(-1) were also tested. Results showed, regardless of matrix complexity, that PAH biodegradation within the four RM substrates, and two MGP soils correlated well with biodegradation predicted by hydroxypropyl-beta-cyclodextrin (HPCD) extraction.

Environmentally friendly assessment of organic compound bioaccessibility using sub-critical water

The evaluation of microbial availability of contaminants is of high importance for better reflecting the processes governing contaminant fate in soil and for establishing the risk associated with contaminated sites. A sub-critical water extraction technique was assessed for its potential to determine the microbially degradable fraction of [(14)C]phenanthrene-associated activity in two dissimilar soils at three different ageing times (14, 28 and 49 days). For the majority of determinations, no significant (p>0.05) difference between sub-critical water-extracted (14)C-activity at 160 degrees C and the fraction mineralized by catabolically active Pseudomonas sp. was observed. Collectively, the results suggested that the sub-critical water extraction technique was an appropriate technique for predicting the biodegradable fraction of phenanthrene-associated (14)C-activity in dissimilar soils following increasing soil-contaminant contact time.

Fugacity modelling to predict the distribution of organic contaminants in the soil:oil matrix of constructed biopiles

Level I and II fugacity approaches were used to model the environmental distribution of benzene, anthracene, phenanthrene, 1-methylphenanthrene and benzo[a]pyrene in a four phase biopile system, accounting for air, water, mineral soil and non-aqueous phase liquid (oil) phase. The non-aqueous phase liquid (NAPL) and soil phases were the dominant partition media for the contaminants in each biopile and the contaminants differed markedly in their individual fugacities. Comparison of three soils with different percentage of organic carbon (% org C) showed that the % org C influenced contaminant partitioning behaviour. While benzene showed an aqueous concentration worthy of note for leachate control during biopiling, other organic chemicals showed that insignificant amount of chemicals leached into the water, greatly reducing the potential extent of groundwater contamination. Level II fugacity model showed that degradation was the dominant removal process except for benzene. In all three biopile systems, the rate of degradation of benzo(a)pyrene was low, requiring more than 12 years for soil concentrations from a spill of about 25 kg (100 mol) to be reduced to a concentration of 0.001 microgg(-1). The removal time of 1-methylphenanthrene and either anthracene or phenanthrene was about 1 and 3 years, respectively. In contrast, benzene showed the highest degradation rate and was removed after 136 days in all biopile systems. Overall, this study confirms the association of risk critical contaminants with the residual saturation in treated soils and reinforces the importance of accounting for the partitioning behaviour of both NAPL and soil phases during the risk assessment of oil-contaminated sites.

Application of hydroxypropyl[beta]cyclodextrin to evaluation of polycyclic aromatic hydrocarbon losses during sewage sludges composting

The aims of the present study were to test the application of the non-exhaustive extraction technique (NEET) with hydroxypropyl[beta]cyclodextrin (HPCD) for the evaluation of the content of potentially bioavailable polycyclic aromatic hydrocarbon (PAH) fraction as well as the evaluation of changes in the content of this fraction during composting of municipal sewage sludges. A possibility to apply this method for the forecasting of PAH losses during composting was also studied. Four sludges (from different sewage treatment plants) with varied properties have been selected for the present experiment. The sludges were composted for 76 days. PAH content was determined as extracted with dichloromethane (exhaustive extraction technique) and potentially bioavailable PAH content by means of HPCD (non-exhaustive extraction technique) in both sewage sludges and composts obtained from them. The content of fraction extracted with HPCD ranged from 63.5 to 83.1% depending on the sludge. After composting, a significant lowering of this fraction contribution was noted for 3 sludges. However, in the composts obtained, the fraction extracted with HPCD still constituted 54.7-62.1% of the total PAH content. The composting process clearly influenced a decrease in the bioavailable fraction in the case of 3- and 5-ring PAHs. However, the 4-ring PAHs content of bioavailable fraction did not undergo any significant changes. No satisfactory results were obtained when HPCD was used as a tool to forecast PAH losses. In a number of cases only, PAH remaining after HPCD extraction achieved a value similar to that of PAH after the composting process. In the case of a number of PAH, the method with HPCD application changed the values of the bioavailable fraction.

Microbial interactions with organic contaminants in soil: definitions, processes and measurement

There has been and continues to be considerable scientific interest in predicting bioremediation rates and endpoints. This requires the development of chemical techniques capable of reliably predicting the bioavailability of organic compounds to catabolically active soil microbes. A major issue in understanding the link between chemical extraction and bioavailability is the problem of definition; there are numerous definitions, of varying degrees of complexity and relevance, to the interaction between organic contaminants and microorganisms in soil. The aim of this review is to consider the bioavailability as a descriptor for the rate and extent of biodegradation and, in an applied sense, bioremediation of organic contaminants in soil. To address this, the review will (i) consider and clarify the numerous definitions of bioavailability and discuss the usefulness of the term 'bioaccessibility'; (ii) relate definition to the microbiological and chemical measurement of organic contaminants' bioavailability in soil, and (iii) explore the mechanisms employed by soil microorganisms to attack organic contaminants in soil.

In vitro bioaccessibility of soil-bound polycyclic aromatic hydrocarbons in successive digestive compartments in cows

Ruminants, which have a central place in the food chain, ingest soil that may contain pollutants. The bioaccessibility of three different polycyclic aromatic hydrocarbon compounds from soil was studied using an in vitro model based on the digestive tract of cows. For this purpose, pasture soil was spiked with (14)C radio-labeled compounds, aged, and then exposed to conditions which simulated the digestive compartments of the rumen, abomasum, and intestines. Our results show that aging generally reduced the bioaccessibility of all the compounds tested. Total bioaccessibilty in the first digestive compartment, i.e., the rumen, depended on the considered compound: elevated for phenanthrene (17-24%), moderate for pyrene (6.6-8.1%), and low for benzo[ a]pyrene (2.3-3.6%). Bioaccessibility was very low in abomasal acidity (generally <2%) and intestinal colloids (<8%). The liquid phases of intestinal medium successfully extracted compounds from freshly contaminated soil (25-28%), but the bioaccessibilty dropped markedly after aging (17% for phenanthrene and <9% for the more lipophylic compounds). Total bioaccessibilty in this in vitro model ranged from 11% for benzo[ a]pyrene in aged soil to 58% for phenanthrene in freshly contaminated soil, and the bioaccessibility of this latter compound was always higher compared to pyrene or benzo[ a]pyrene. Residual soil contained around half of the initial load, the highest residual levels being of benzo[ a]pyrene, which confirms the observed bioaccessibility.

Prediction of microbial accessibility of carbon-14-phenanthrene in soil in the presence of pyrene or benzo[a]pyrene using an aqueous cyclodextrin extraction technique

Traditionally, solvent extractions are routinely used in the assessment of contaminated land. However, vigorous solvent extractions only give total concentrations rather than that relating to the bioaccessible fraction. Recently, less harsh, aqueous-based extraction methods have been shown to be a better estimate of the microbial degradation of polycyclic aromatic hydrocarbons (PAHs). The aqueous-based hydroxypropyl-beta-cyclodextrin (HPCD) extraction technique was tested using 14C-PAHs in soils and compared against indigenous microbial mineralization (a measure of bioaccessibility) of 14C-phenanthrene in the presence of pyrene or benzo[a]pyrene (B[a]P) over a range of concentrations (0, 5, 10, or 50 mg kg(-1)) and aged for 0, 25, 50, and 100 d in four soils. At each time point, the total loss, extractability, and mineralization of 14C-phenanthrene was measured in each of the soils. The presence of the other PAHs had little effect on the behavior of 14C-phenanthrene in any of the soils. Comparisons between the amounts of 14C-phenanthrene extracted using HPCD and mineralized were made and showed that there was a correlation (1:1). This study demonstrates that HPCD extraction is able to predict the microbial accessibility fraction of 14C-phenanthrene in the presence of other PAHs in a range of soils, further supporting the applicability of this technique.

Cyclodextrin enhanced biodegradation of polycyclic aromatic hydrocarbons and phenols in contaminated soil slurries

This work aimed to evaluate the relative contribution of soil catabolic activity, contaminant bioaccessibility, and nutrient levels on the biodegradation of field-aged polycyclic aromatic hydrocarbons and phenolic compounds in three municipal gas plant site soils. Extents of biodegradation achieved, in 6 week-long soil slurry assays, under the following conditions were compared: (i) with inoculation of catabolically active PAH and phenol-degrading microorganisms, (ii) with and without hydroxypropyl-beta-cyclodextrin supplementation (HPCD; 100 g L(-1)), and finally (iii) with the provision of additional inorganic nutrients in combination with HPCD. Results indicated no significant (p < 0.05) differences between biodegradation endpoints attained in treatments inoculated with catabolically active microorganisms as compared with the uninoculated control. Amendments with HPCD significantly (p < 0.05) lowered biodegradation endpoints for most PAHs and phenolic compounds. Only in one soil did the combination of HPCD and nutrients consistently achieve better bioremediation endpoints with respect to the HPCD-only treatments. Thus, for most compounds, biodegradation was not limited by the catabolic activity of the indigenous microorganisms but rather by processes resulting in limited availability of contaminants to degraders. It is therefore suggested that the bioremediation of PAH and phenol impacted soils could be enhanced through HPCD amendments. In addition, the biodegradability of in situ and spiked (deuterated analogues) PAHs following 120 days aging of the soils suggested that this contact time was not sufficient to obtain similar partitions to that observed for field-aged contaminants; with the spiked compounds being significantly (p < 0.05) more available for biodegradation.

Diffuse PAH contamination of surface soils: environmental occurrence, bioavailability, and microbial degradation

The purpose of this review is to recognize the scientific and environmental importance of diffuse pollution with polycyclic aromatic hydrocarbons (PAHs). Diffuse PAH pollution of surface soil is characterized by large area extents, low PAH concentrations, and the lack of point sources. Urban and pristine topsoils receive a continuous input of pyrogenic PAHs, which induces a microbial potential for PAH degradation. The significance of this potential in relation to black carbon particles, PAH bioaccessibility, microbial PAH degradation, and the fate of diffuse PAHs in soil is discussed. Finally, the state-of-the-art methods for future investigations of the microbial degradation of diffuse PAH pollution are reviewed.

Prediction of PAH biodegradation in field contaminated soils using a cyclodextrin extraction technique

Biodegradation has been identified as a major loss process for organic contaminants in soils and, as a result, microbial strategies have been developed for the remediation of contaminated land. Prediction of the biodegradable fraction would be important for determining bioremediation end-points in the clean-up of contaminated land. The aim of this study was to investigate the ability of a cyclodextrin extraction to predict the extent to which polycyclic aromatic hydrocarbons (PAHs) would be degraded microbiologically in field contaminated soils; further testing the robustness and reproducibility of this extraction in chemically complex systems. Dichloromethane and hydroxypropyl-beta-cyclodextrin (HPCD) extractable fractions were measured together with the PAH biodegradable fraction in each of the six field contaminated soils. The amounts of PAHs degraded by the catabolic activity of the indigenous microflora in each of the soils were correlated with HPCD-extractable PAH concentrations. The regressions showed that the amounts of lower molecular weight PAHs extracted by the HPCD were not significantly (P > 0.05) different to the amounts that were degraded. However, higher molecular weight PAHs that were extracted by HPCD did differ significantly (P < 0.05) from the amounts degraded. Although the HPCD extraction did overestimate the microbially degradable fraction of the higher molecular weight PAHs, overall the correlations between the HPCD extractable fraction and the microbially degradable fraction were very close, with mean values of the slope of line for the six soils equalling 1. This study further describes the robust and reproducible nature of the aqueous-based soil extraction technique reliably measuring the extent to which PAHs will be microbially degraded in soil.

Intra-laboratory evaluation of Microbial Assay for Risk Assessment (MARA) for potential application in the implementation of the Water Framework Directive (WFD)

The Microbial Assay for Risk Assessment (MARA) is an innovative system based on an array of 11 different microbial species freeze-dried in a 96-well micro-titre plate format. Developed for testing the toxicity of chemicals, mixtures and environmental samples, the assay employs species of a taxonomically diverse range. In addition to ten prokaryotic species, a eukaryote (yeast) is included in the range. The MARA's innate scope of a multi-dimensional test allows determination of toxicity based on a unique assay fingerprint or index, numerically expressed as the mean Microbial Toxic Concentration (MTC). The most significant potential of the test is in the additional inference that can be conveyed to the toxicity evaluation because of the presence of each of the constituent species. In view of the fact that conventional aquatic bioassays, like fish or cladoceran tests, are expensive and impractical, the MARA could provide a cost-effective solution for routine ecotoxicological testing. The performance of the MARA was evaluated to ascertain its capability and potential scope. Sensitivity to toxicants and different environmental samples was assessed. Evaluation included comparison with other tests: namely Microtox, invertebrate (Daphnia magna and Thamnocephalus platyurus) microbiotests, and respiration-inhibition and nitrification-inhibition tests. The most sensitive invertebrate test was found to be the T. platyurus microbiotest for three of the four metals tested. The LC(50) values for this test for Cd(ii), Cr(vi) and As(iii) were 0.2, 0.018 and 0.3 mg l(-1), respectively; and the corresponding most sensitive MARA species MTC values were 4.4, 2.8 and 17 mg l(-1), respectively.