A green biochar/iron oxide composite for methylene blue removal

Sustainable efficient utilization of magnetic porous biochar for adsorption of orange G and tetracycline: Inherent roles of adsorption and mechanisms

Iron-doped biochar has been widely used as an adsorbent to remove contaminants due to the high adsorption performance, but it still suffers from complicated preparation methods, unstable iron loading, unsatisfactory specific surface area, and uneven distribution of active sites. Here, a novel magnetic porous biochar (FeCS800) with nanostructure on surface was synthesized by one-pot pyrolysis method of corn straw with K2FeO4, and used in orange G (OG) and tetracycline (TC) adsorption. FeCS800 exhibited outstanding adsorption capacities for OG and TC after K2FeO4 activation and the adsorption data were fitted satisfactorily to Langmuir isotherm and Pseudo-second-order kinetic model. The maximum adsorption capacities of FeCS800 for OG and TC were around 303.03 mg/g and 322.58 mg/g, respectively, at 25 °C and pH 7.0, which were 16.27 and 24.61 times higher than that before modification. Thermodynamic studies showed that the adsorption of OG/TC by FeCS800 were thermodynamically favorable and highly spontaneous. And the adsorption capacity of OG and TC by FeCS800 remained 77% and 81% after 5 cycles, respectively, indicating that FeCS800 had good stability. The outstanding adsorption properties and remarkable reusability of FeCS800 show its great potential to be an economic and environmental adsorbent in contaminants removal.

Dual biomass-derived porous carbon heterogeneous functionalized mesoporous CuCo2O4 nanocomposite combined with molecularly imprinted polymers as an electrochemical sensing platform for hypersensitive and selective determination of dimetridazole contaminants

In this study, an original molecularly imprinted electrochemical sensor (MIECS) is prepared using layer-by-layer modification of sensitization nanomaterials (CuCo2O4/BPC-E) coupled with molecularly imprinted polymers (MIPs) for the ultrasensitive and rapid determination of dimetridazole (DMZ) contaminants. The biomass waste of eggshell (ES) powders subtly introduced in situ in the carbonization process of psyllium husk (PSH) substantially promotes the physicochemical properties of the resulting biomass-derived porous carbon (BPC-E). The large specific surface area and abundant pores provide a favourable surface for loading mesoporous CuCo2O4 with a spinel structure. The assembly of CuCo2O4/BPC-E on the gold electrode (GE) surface enhances the electrochemical sensing signal. The MIPs constructed using DMZ and o-phenylenediamine (oPD) as templates and functional monomers boost the targeted recognition performance of the analyte. The combined DMZ targets then undergo an electrochemical reduction reaction in situ with the transfer of four electrons and four protons. Under optimum conditions, the current response of differential pulse voltammetry (DPV) exhibits two linear ranges for DMZ detection, 0.01-10 μM and 10-200 μM. The limit of detection (LOD) is 1.8 nM (S/N = 3) with a sensitivity of 5.724 μA μM-1 cm-2. The obtained MIECS exhibits excellent selectivity, reproducibility, repeatability and stability. This electrochemical sensing system is applied to the detection of real samples (tap water, coarse fodder and swine urine), yielding satisfactory recoveries (90.6%-98.1 %), which are consistent with those obtained via HPLC. This finding verifies that the utility of MIECS for monitoring pharmaceutical and environmental contaminants and ensuring food safety.

Structural properties and adsorption performance relationship towards three categories of lignin and their derived biochar

The growing interest in utilizing lignin for dye removal has gained momentum, but there is limited information on the intricate relationship between lignin structural characteristics and adsorption efficacy, especially for its biochar derivatives. This study focused on three types of lignin and their corresponding biochar derivatives. Among them, ZnCl2-activated acidic/alkali densified lignin preparation of lignin-derived active carbon exhibited superior adsorption performance, achieving 526.32 mg/g for methylene blue and 2156.77 mg/g for congo red. Its exceptional adsorption capacity was attributed to its unique structural properties, including low alkyl and O-alkyl group content and high aromatic carbon levels. Furthermore, the adsorption mechanisms adhered to pseudo-second-order kinetics and the Langmuir model, signifying a spontaneous process. Intriguingly, lignin-derived active carbon also demonstrated remarkable recovery capabilities. These findings provide valuable insights into the impact of structural attributes on lignin and its biochar's adsorption performance.

Properties and Possibilities of Using Biochar Composites Made on the Basis of Biomass and Waste Residues Ferryferrohydrosol Sorbent

Biochar enriched with metals has an increased potential for sorption of organic and inorganic pollutants. The aim of the research was to identify the possibility of using biochar composites produced on the basis of waste plant biomass and waste FFH (ferryferrohydrosol) containing iron atoms, after CO2 capture. The composites were produced in a one-stage or two-stage pyrolysis process. Their selected properties were determined as follows: pH, ash content, C, H, N, O, specific surface area, microstructure and the presence of surface functional groups. The produced biochar and composites had different properties resulting from the production method and the additive used. The results of experiments on the removal of methylene blue (MB) from solutions allowed us to rank the adsorbents used according to the maximum dye removal value achieved as follows: BC1 (94.99%), B (84.61%), BC2 (84.09%), BC3 (83.23%) and BC4 (83.23%). In terms of maximum amoxicillin removal efficiency, the ranking is as follows: BC1 (55.49%), BC3 (23.51%), BC2 (18.13%), B (13.50%) and BC4 (5.98%). The maximum efficiency of diclofenac removal was demonstrated by adsorbents BC1 (98.71), BC3 (87.08%), BC4 (74.20%), B (36.70%) and BC2 (30.40%). The most effective removal of metals Zn, Pb and Cd from the solution was demonstrated by BC1 and BC3 composites. The final concentration of the tested metals after sorption using these composites was less than 1% of the initial concentration. The highest increase in biomass on prepared substrates was recorded for the BC5 composite. It was higher by 90% and 54% (for doses of 30 g and 15 g, respectively) in relation to the biomass growth in the soil without additives. The BC1 composite can be used in pollutant sorption processes. However, BC5 has great potential as a soil additive in crop yield and plant growth.

Functionalization of porous silica with graphene oxide and polyethyleneimine, containing zinc copper ferrite nanoparticles for water treatment and antibacterial application

The article discusses the removal of methylene blue (MB) dye, a common cationic dye used in the textile industry, from aqueous solutions through an adsorption process. The use of porous components as adsorbents are shown to facilitate complete separation after the process is completed. The substrate was synthesized by connecting zinc copper ferrite (ZnCuFe2O4), polyethyleneimine (PEI), and Graphene Oxide (GO) sheets to MCM-48, which is a mesoporous material. The surface of MCM-48 was modified using CPTMS, which created an O-Si-Cl bridge, thereby improving the adsorption rate. The substrate was shown to have suitable sites for electrostatic interactions and creating hydrogen bonds with MB. The adsorption process from the Freundlich isotherm (R2 = 0.9224) and the pseudo-second-order diagram (R2 = 0.9927) demonstrates the adsorption of several layers of dye on the heterogeneous surface of the substrate. The synthesized substrate was also shown to have good bactericidal activity against E. coli and S. aureus bacterial strain. Furthermore, the substrate maintained its initial ability to adsorb MB dye for four consecutive cycles. The research resulted that ZnCuFe2O4@MCM-48/PEI-GO substrate has the potential for efficient and economical removal of MB dye from aqueous solutions (R = 88.82%) (qmax = 294.1176 mg. g-1), making it a promising solution for the disposal of harmful industrial waste.

A green and economic approach to synthesize magnetic Lagenaria siceraria biochar (γ-Fe2O3-LSB) for methylene blue removal from aqueous solution

In the printing and textile industries, methylene blue (a cationic azo dye) is commonly used. MB is a well-known carcinogen, and another major issue is its high content in industrial discharge. There are numerous removal methodologies that have been employed to remove it from industrial discharge; however, these current modalities have one or more limitations. In this research, a novel magnetized biochar (γ-Fe2O3-LSB) was synthesized using Lagenaria siceraria peels which were further magnetized via the co-precipitation method. The synthesized γ-Fe2O3-LSB was characterized using FTIR, X-ray diffraction, Raman, SEM-EDX, BET, and vibrating sample magnetometry (VSM) for the analysis of magnetic properties. γ-Fe2O3-LSB showed a reversible type IV isotherm, which is a primary characteristic of mesoporous materials. γ-Fe2O3-LSB had a specific surface area (SBET = 135.30 m2/g) which is greater than that of LSB (SBET = 11.54 m2/g). γ-Fe2O3-LSB exhibits a saturation magnetization value (Ms) of 3.72 emu/g which shows its superparamagnetic nature. The batch adsorption process was performed to analyze the adsorptive removal of MB dye using γ-Fe2O3-LSB. The adsorption efficiency of γ-Fe2O3-LSB for MB was analyzed by varying parameters like the initial concentration of adsorbate (MB), γ-Fe2O3-LSB dose, pH effect, contact time, and temperature. Adsorption isotherm, kinetic, and thermodynamics were also studied after optimizing the protocol. The non-linear Langmuir model fitted the best to explain the adsorption isotherm mechanism and resulting adsorption capacity ( q e =54.55 mg/g). The thermodynamics study showed the spontaneous and endothermic nature, and pseudo-second-order rate kinetics was followed during the adsorption process. Regeneration study showed that γ-Fe2O3-LSB can be used up to four cycles. In laboratory setup, the cost of γ-Fe2O3-LSB synthesis comes out to be 162.75 INR/kg which is low as compared to commercially available adsorbents. The results obtained suggest that magnetic Lagenaria siceraria biochar, which is economical and efficient, can be used as a potential biochar material for industrial applications in the treatment of wastewater.

Valorization of Waste Watermelon Rinds as a Bio-adsorbent for Efficient Removal of Methylene Blue Dye from Aqueous Solutions

Nature-based solutions (NBSs) for remediation of various emerging contaminants have gained impetus during the last few decades. In the current study, watermelon (citrullus lanatus), a highly consumed seasonal fruit, was used as a feedstock waste biomass for biochar synthesis through valorization of watermelon rinds. The watermelon biochar (WM-BC) was synthesized through slow pyrolysis at 550°C under anoxic conditions. Langmuir model with R2>99, was found to best fit the adsorption isotherm, and the adsorption kinetics was best described by the pseudo-second-order model. Various characterization tools including FTIR, SEM, BET, XRD, and TEM were used to evaluate the surface morphology of the biochar. The removal efficiency increased from 35% (dosage = 0.4 g), to 81% at WM-BC dosage of 2 g. A maximum adsorption capacity of 115.61 mg/g was found. The results from kinetic and isotherm model model suggested that the adsorption was favorable and multilayer adsorption can be considered. The adsorption mechanism was found to be governed by the co-existing factors such as hydrogen bonding, electrostatic interactions, and aromatic interactions. Results suggest that WM-BC has high potential to be employed as an adsorbent for efficient remediation of methylene blue dyes from aqueous solutions.

Evaluation of iron-modified biochar on arsenic accumulation by rice: a pathway to assess human health risk from cooked rice

Arsenic (As) contamination of rice grain poses a serious threat to human health. Therefore, it is crucial to reduce the bioavailability of As in the soil and its accumulation in rice grains to ensure the safety of food and human health. In this study, mango (Mangifera indica) leaf-derived biochars (MBC) were synthesized and modified with iron (Fe) to produce FeMBC. In this study, 0.5 and 1% (w/w) doses of MBC and FeMBC were used. The results showed that 1% FeMBC enhanced the percentage of filled grains/panicle and biomass yield by 17 and 27%, respectively, compared to the control. The application of 0.5 and 1% FeMBC significantly (p < 0.05) reduced bioavailable soil As concentration by 33 and 48%, respectively, in comparison to the control. The even higher As flux in the control group as compared to the biochar-treated groups indicates the lower As availability to biochar-treated rice plant. The concentration of As in rice grains was reduced by 6 and 31% in 1% MBC and 1% FeMBC, respectively, compared to the control. The reduction in As concentration in rice grain under 1% FeMBC was more pronounced due to reduced bioavailability of As and enhanced formation of Fe-plaque. This may restrict the entry of As through the rice plant. The concentrations of micronutrients (such as Fe, Zn, Se, and Mn) in brown rice were also improved after the application of both MBC and FeMBC in comparison to the control. This study indicates that the consumption of parboiled rice reduces the health risk associated with As compared to cooked sunned rice. It emphasizes that 1% MBC and 1% FeMBC have great potential to decrease the uptake of As in rice grains.

Waste derived modified biochar as promising functional material for enhanced water remediation potential

The waste management and water purification are daunting environmental challenges. Biochar, a carbonaceous material prepared from diverse organic waste (agricultural, household residues and municipal sewage sludge) has garnered substantial attention due to its excellent attributes, including carbon content, cation exchange efficacy, ample specific surface area, and structural robustness. Thus, the present review comprehensively analyzes bio waste-derived biochar with a particular emphasis on water remediation applications. This article primarily delves into various strategies for modifying biochar, elucidating the underlying mechanisms behind these modifications and their potential for bolstering pollutant removal efficiency. Furthermore, it addresses the impact of functionalization on both biochar stability and cost for commercialization. Lastly, the article outlines key developments, SWOT analysis, and future prospects, offering insights into the practical execution of biochar applications at a larger scale. Therefore, this article paves the way for future research to deepen the understanding of modified biochar with mechanisms for exploring water remediation applications in a more sustainable manner.

Adsorption behavior and mechanism of modified Pinus massoniana pollen microcarriers for extremely efficient and rapid adsorption of cationic methylene blue dye

Herein, a novel biosorbent was successfully fabricated through a two-step process employing Pinus massoniana pollen as raw material. The efficacy of this biosorbent in eliminating methylene blue (MB), a typical organic cationic dye, from highly concentrated industrial wastewater was investigated. The results demonstrated that by adjusting the wettability of pollen microcarriers, it is possible to significantly increase their adsorption capacity for cationic dyes, resulting in a remarkable 25-fold improvement. The modified Pinus massoniana pollen microcarriers (MPPMC) exhibited an optimal adsorption capacity (585 mg/g) under specific conditions and a rapid equilibrium (97.6% in 5 min, uptake 487.8 mg/g) even at room temperature, showing excellent performance in removing MB efficiently and quickly. It is worth noting that the modified microcarriers could be regenerated via a simple pH-controlled adsorption-desorption cycle, maintaining their superior efficiency (> 99%) even after undergoing five cycles, indicating their excellent reproducibility. The MB adsorption process on MPPMC obeyed the pseudo-second-order kinetic model and followed the Langmuir model. Through the introduced modifications, the substantial deprotonation of carboxyl groups notably augmented electrostatic and hydrogen bonding interactions between MPPMC and MB. Overall, this study offers a sustainable, eco-friendly biological adsorbent, and the MPPMC exhibit the considerable potential for efficient and rapid removal of organic cationic dyes in wastewater.

Advances in Fe-modified lignocellulosic biochar: Impact of iron species and characteristics on wastewater treatment

Lignocellulosic biomass is an attractive feedstock for biochar production owing to its high abundance and renewability. Various modified biochars have been extensively studied for wastewater treatment to improve the physical and chemical properties of lignocellulosic biochar (L-BC). Particularly, Fe-modified L-BCs have garnered attention owing to the abundance and eco-friendliness of Fe and the outstanding ability to remove various organic and inorganic contaminants via adsorption, oxidation, reduction, and catalytic reactions. Different iron species (e.g., Fe(0), Fe (hydr)oxide, Fe sulfide, and Fe-Metal) are formed during the preparation of Fe-L-BCs, which can completely differentiate the physical and chemical properties of BCs. This review discusses the advances in the synthesis of different Fe-L-BCs, specific changes in the physical and chemical properties of Fe-L-BCs upon Fe addition, and their impacts on wastewater treatment. The results of this review can demonstrate the unique advantages and drawbacks of Fe-L-BCs for the removal of different types of pollutants.

Photocatalytic Degradation of Antibiotics via Exploitation of a Magnetic Nanocomposite: A Green Nanotechnology Approach toward Drug-Contaminated Wastewater Reclamation

In the quest for eco-conscious innovations, this research was designed for the sustainable synthesis of magnetite (Fe3O4) nanoparticles, using ferric chloride hexahydrate salt as a precursor and extract of Eucalyptus globulus leaves as both a reducing and capping agent, which are innovatively applied as a photocatalyst for the photocatalytic degradation of antibiotics "ciprofloxacin and amoxicillin". Sugar cane bagasse biomass, sugar cane bagasse pyrolyzed biochar, and magnetite/sugar cane bagasse biochar nanocomposite were also synthesized via environmentally friendly organized approaches. The optimum conditions for the degradation of ciprofloxacin and amoxicillin were found to be pH 6 for ciprofloxacin and 5 for amoxicillin, dosage of the photocatalyst (0.12 g), concentration (100 mg/L), and irradiation time (240 min). The maximum efficiencies of percentage degradation for ciprofloxacin and amoxicillin were found to be (73.51%) > (63.73%) > (54.57%) and (74.07%) > (61.55%) > (50.66%) for magnetic nanocomposites, biochar, and magnetic nanoparticles, respectively. All catalysts demonstrated favorable performance; however, the "magnetite/SCB biochar" nanocomposite exhibited the most promising results among the various catalysts employed in the photocatalytic degradation of antibiotics. Kinetic studies for the degradation of antibiotics were also performed, and notably, the pseudo-first-order chemical reaction showed the best results for the degradation of antibiotics. Through a comprehensive and comparative analysis of three unique photocatalysts, this research identified optimal conditions for efficient treatment of drug-contaminated wastewater, thus amplifying the practical significance of the findings. The recycling of magnetic nanoparticles through magnetic separation, coupled with their functional modification for integration into composite materials, holds significant application potential in the degradation of antibiotics.

Novel soy protein isolate/sodium alginate-based functional aerogel for efficient uptake of organic dye from effluents

In response to the increasing global concern regarding water pollution, there is a growing demand for the development of novel adsorbents capable of effectively eliminating hazardous organic pollutants from effluents. In this study, we present a functional soy protein isolate (SPI)/sodium alginate (ALG)/polyethyleneimine (PEI) aerogel prepared via a facile chemical crosslinking process as a novel adsorbent with excellent capabilities for removing toxic methyl blue (MB) dye from effluents. Thanks to the synergistic dense oxygen and nitrogen-containing functional groups in the networks, the ALG/SPI/PEI (ASP) aerogel displayed high adsorption capacity for MB (106.3 mg/g) complying the adsorption kinetics and isotherm with the pseudo-second-order and Langmuir models, respectively. Remarkably, the MB adsorption capability of the ASP aerogel surpasses that of its pristine counterpart and outperforms recently reported adsorbents. Moreover, the aerogel maintained >80% of initial adsorption capability in the fourth regenerative cycle, indicating excellent reusability. The superior MB adsorbability coupled with high-efficiency regenerability in this study reveal the significant potential of ASP aerogel in efficiently eliminating organic dye from wastewater.

Amino-grafted Biochar as a Novel Photocatalyst for degradation of high concentration dye

Photocatalytic degradation of organic pollution by biochar was a sustainable strategy for waste water remediation, nevertheless, it still suffers drawbacks like low efficiency due to the poor photocatalytic properties of pristine biochar. Herein, amino groups were grafted on the edge sites/defects of biochar by Friedel-Crafts acylation to enhance the degradation of high concentration dye solutions. The results suggested that the amino groups played an important role in imparting photocatalytic properties to biochar. Owing to the strong Lewis basicity and electron-donating ability of amino groups, their interaction with oxygen-containing functional groups/aromatic structures in biochar was improved, which enhanced the electron exchange ability of biochar under visible light irradiation, resulting in excellent degradation performances of high concentration RhB (∼10 times faster than ungrafted biochar). In this work, amino-grafted garlic peel biochar delivered a new idea for the future direction of biochar-based photocatalysis in wastewater remediation.

Removal of polystyrene microplastics using biochar-based continuous flow fixed-bed column

In the realm of environmental challenges, microplastics have emerged as a pressing threat, presenting risks to both individuals and ecosystems. Conventional treatment plants are presently not equipped for effectively removing these minute contaminants. This study presents an investigation into the potential of a continuous flow biochar column, utilizing biochar derived from banana peel through a nitrogen-free slow pyrolysis process for the removal of microplastics. A systematic exploration of various parameters, including bed height, flow rate, inflow microplastic concentration, and microplastic size is undertaken to discern their impact on polystyrene removal efficiency. A peak removal efficiency of 92.16% has been achieved under specific conditions: a 6-cm bed height, a 3-mL/min flow rate, an inlet concentration of 0.05 g/L, and microplastic sizes ranging from 150 to 300 µm. The removal efficiency was inversely affected by flow rate while directly influenced by bed height. To deepen the understanding of polystyrene removal on biochar, a detailed characterization of the synthesized material was carried out. The removal of microplastics by banana peel biochar (BPB) is observed to be dominated by adsorption and filtration processes. The entanglement of microplastics with minuscule biochar granules, capture between particles, and entrapment in the porous system were identified as the mechanisms of removal. Leveraging the hydrophobic nature of polystyrene microplastics, interactions with the hydrophobic functional groups in BPB result in effective adsorption. This is further complemented by self-agglomeration and filtration mechanisms that synergistically contribute to the elimination of larger agglomerates. The findings thus provide a comprehensive understanding, offering hope for a more effective strategy in mitigating the environmental impact of microplastics.

Effects of cation types in persulfate on physicochemical and adsorptive properties of biochar prepared from persulfate-pretreated bamboo

The adsorption behaviors of biochar are largely impacted by biomassfeedstock. In this study, two biochars were prepared from torrefaction of ammonium persulfate- and potassium persulfate-pretreated bamboo and then activated by cold alkali, which are named as ASBC and KSBC, respectively. The two biochars were characterized by different instruments, and their adsorption properties over cationic methylene blue (MB) were compared. The type of persulfates little affected the specific surface areas, but significantly impacted O (29.54 % vs. 35.113 %) and N (12.13 % vs. 3.74 %) contents, functional groups, and zeta potentials of biochars. MB adsorption onto ASBC/KSBC is a single-layer chemical endothermic process and ASBC/KSBC exhibit high adsorption capacity over MB (475/881 mg·g-1) at 303 K. Obviously, the sorption capacity of MB onto KSBC much surpasses that of MB onto ASBC. These results indicate biomass pre-treatment is a cheap and convenient method to prepare biochars with unique physicochemical and adsorptive properties.

Emerging iron-based mesoporous materials for adsorptive removal of pollutants: Mechanism, optimization, challenges, and future perspective

Iron-based materials (IBMs) have shown promise as adsorbents due to their unique physicochemical properties. This review provides an overview of the different types of IBMs, their synthesis methods, and their properties. Results found in the adsorption of emerging contaminants to a wide range of IBMs are discussed. The IBMs used were evaluated in terms of their maximum uptake capacity, with special consideration given to environmental conditions such as contact time, solution pH, initial pollutant concentration, etc. The adsorption mechanisms of pollutants are discussed taking into account the results of kinetic, isotherm, thermodynamic studies, surface complexation modelling (SCM), and available spectroscopic data. A current overview of molecular modeling and simulation studies related to density functional theory (DFT), surface response methodology (RSM), and artificial neural network (ANN) is presented. In addition, the reusability and suitability of IBMs in real wastewater treatment is shown. The review concludes with the strengths and weaknesses of current research and suggests ideas for future research that will improve our ability to remove contaminants from real wastewater streams.

Reshaping environmental sustainability: Poultry by-products digestate valorization for enhanced biochar performance in methylene blue removal

Anaerobic digestion is a highly effective and innovative method for treating organic waste while simultaneously generating energy. However, the treatment of the resulting digestate remains a challenging endeavor. To address this issue, poultry by-products digestate is used in this study to prepare biochars at two different pyrolysis temperatures (500/600 °C). Despite their potential, the utilization of untreated biochar is restricted due to its inadequate adsorption capacity. Therefore, each biochar was chemically activated using either HNO3 or KOH to synthesize four activated biochars (BC5@KOH, BC6@HNO3, BC5@HNO3, and BC6@HNO3). The aim is to investigate how the nature of chemical activation and pyrolysis temperature influence the adsorption of methylene blue dye. Characterization techniques, including X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, scanning electron microscopy (SEM), Raman analysis, and pHpzc determination, were exploited to comprehensively elucidate the structure and composition of both unprocessed and chemically activated biochars. Among the activated biochars, the adsorbent BC5@HNO3 exhibits the highest methylene blue (MB) adsorption capacity, reaching 101.72 mg.g-1 at 298 K under (pH = 2, ads dose = 0.6 g.L-1, shaking time of 20 min, as optimal conditions for MB adsorption. Adsorption data for each adsorbent strongly aligns with both the Langmuir isotherm model and the pseudo-second-order kinetic model. Moreover, the thermodynamic study reveals that the adsorption process was endothermic and spontaneous. The adsorption mechanism of MB dye was explored using various analytical techniques, including FTIR, SEM, PZC, and pH impact assessment. The findings suggest correlations with electrostatic interactions, hydrogen bonding, pore filling, as well as n-π and π-π interactions. Apparently, activated biochars play a crucial role in efficiently removing methylene blue dye, showcasing their potential as environmentally friendly and effective adsorbents.

Co-pyrolysis of orange peel and eggshell for oxygenated rich composite: Process optimization with response surface methodology

Co-pyrolysis of orange peel and chicken eggshell was performed for the synthesis of the composite, a co-pyrolysis technique used to promote natural fabrication and to allow the raw material elemental combination effect and the preparatory conditions such as pyrolysis temperature, residence time, and eggshell/orange peel mixing ratio, to be optimized with the response surface methodology through Box-Behnken Design(BBD). BBD involved a randomized series of 17 experimental runs, and the best optimal conditions were found with a pyrolysis temperature of 300 °C, a residence time of 1 h, and 0.5 as the mixing ratio. These conditions gave a maximum adsorption capacity of 167 mg/g for removal of the modal pollutant methylene blue. FTIR spectra of the composite showed new functional peaks of oxygenated groups, at two different bands. XRD confirmed an amorphous surface with inorganic component peaks, while SEM-EDS revealed rich defects sites along with an enhanced percentage of oxygen elements on the surface; the surface area was enhanced from 1 m2 with unmodified peel to 64 m2 with composite. The adsorption behavior of the composite was studied for dye removal and the adsorption behavior was well explained by the Langmuir isotherm model.

Green synthesis of MnO2-embedded Rauvolfia tetraphylla leaves (MnO2@RTL) for crystal violet dye removal and as an antibacterial agent

The application of green synthesized nanocomposites for the prevention of environmental pollution is increasing nowadays. Here, a green composite has been synthesized by embedding MnO2 on Rauvolfia tetraphylla leaves using its leaf extract hereinafter termed as MnO2@RTL, and demonstrated for crystal violet (CV) dye removal from simulated and real wastewater. The surface properties of the material were determined by scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM-EDX), Fourier transform infrared spectra (FTIR), X-ray diffraction (XRD), and Brunauer-Emmet-Teller (BET) surface area, pHZPC, and zeta potential. The material exhibits a remarkable adsorption capacity of 61.162 mg/g at 328 K and pH 7. The adsorption was best fitted with Pseudo-second-order kinetic (R2 = 0.998) and a combination of Langmuir and Freundlich isotherm model (R2 = 0.994-0.999). The thermodynamic study revealed spontaneous (ΔG values =  - 2.988 to - 4.978 kJ/mol) and endothermic (ΔH values = 6.830 to 11.018 kJ/mol) adsorption. After adsorption, 80% regeneration occurred with 50% methanol, and recycled up to five times. Advantageously, the material was able to remove CV dye in the presence of coexistent ions and from industrial wastewater, confirming field applicability. The adsorption capacity of the material is superior to previously reported materials. The standard deviation and relative standard deviations have been evaluated to be 0.000422-0.000667 and 0.473-0.749%, which suggests the reliability of the experiments. The exhausted material, after recycling, was pyrolyzed to overcome the disposal problem. It was established as a secondary adsorbent with 73% efficiency which makes the material win-win. The material showed antibacterial properties with Staphylococcus aureus bacteria with a zone of inhibition 5 mm.

FeS and Fe3O4 Co-modified biochar to build a highly resistant advanced oxidation process system for quinclorac degradation in irrigation water

Advanced oxidation processes (AOPs), based on sulfate radical (SO4·-) produced by peroxymonosulfate (PMS), can effectively mineralize refractory organic pollutants. However, the coexistence of anions and natural organic matters in actual wastewater prevents the application of AOPs. A simple one-step method was used to prepare FeS/Fe3O4 co-modified biochar materials (FFB) that could activate PMS to degrade quinclorac (QNC) with a removal rate of 100%, even exhibiting optimum degradation of QNC reached 99.31% in irrigation water, demonstrating excellent anti-interference performance for co-existing anions and natural organic matter. Meanwhile, ecotoxicity analysis showed that the toxicity of degradation intermediates was lower than that of QNC. Characterization results demonstrated the even distribution of FeS and Fe3O4 onto biochar, supplying abundant Fe2+ to activate PMS producing reactive oxygen species (ROS), while the generated Fe3+ after reactive continue to be reduced with sulfur species to promote the cycle of Fe2+/Fe3+. The coexistence of ·OH, SO4·-, 1O2, and O2·- in the FFB/PMS-QNC system suggest the possession of two pathway with free radical and non-free radical pathways to degrade QNC. The density functional theory (DFT) was used to analyze the adsorption sites and adsorption energy of PMS, as well as the differential charge density, which further proved the generation of SO4·-, O2·- and 1O2. In addition, the electrochemical test results showed that electron transfer also played an important role in the degradation of QNC. This study provides a feasible approach for the removal of organic pollutants in actual water.

Agricultural waste biochar after potassium hydroxide activation: Its adsorbent evaluation and potential mechanism

The agricultural waste (Goji branch) was pyrolyzed into biochars with one-step potassium hydroxide (KOH) activation under different processing conditions. The biochars were first characterized in structural features and functional groups and then evaluated for adsorptive performance with methylene blue as a model pollutant. Different adsorption models were applied to fit the adsorption process and reveal the possible mechanisms. The adsorption capacity was found to strongly correlate (R2 = 0.9642) with the surface area of the biochars, among which biochar K50%W29%C-700 (pyrolysis at 700 °C in the presence of 50 % KOH and 29 % water) possessed the largest surface area (1378 m2/g) and exhibited the highest adsorption capacity (769 mg/g) compared to its homologous products. Biochar K50%W29%C-700 also showed excellent recyclability and potent adsorption capacity toward other common organic pollutants. The results suggest that traces of water in agricultural wastes could significantly intensify the KOH-involved activation efficiency of producing porous biochar.

A novel biochar composite derived from oil-based drill sludge and cuttings: Structural characterization and electrochemical properties

How to dispose of large quantities of hazardous shale gas drilling waste is an important worldwide problem facing the oil and gas industry. In this study, we report an environmentally friendly and low energy consumption approach (carbonization followed by activation) to convert oil-based drill sludge (OBDS) and oil-based drill cuttings (OBDCs) into biochar composites and investigate the effect of hydrofluoric acid (HF) acidification on them. The biochar composites were prepared using the OBDS, OBDCs, the mixtures of OBDS and OBDCs, and HF treatment the mixtures were named OS, OC, OSC, and OSC-HF, respectively. The characterization result of synthesized biochar composites indicated that the OSC had a larger specific surface area and a higher degree of graphitization. The composites mainly consisted of SiO2 and BaSO4, except for biochar. The OSC electrode exhibited the highest oxygen evolution potential (1.72 V vs Ag/AgCl) and the lowest charge transfer resistance compared with OS, OC, and OSC-HF electrodes, implying that SiO2 plays an important role in electrochemical performance. Using the OSC electrode as an anode, the chemical oxygen demand removal efficiency of the OBDS supernatant was 79.4 ± 0.95%. Further, the OSC electrode could maintain higher degradation efficiency and stability after the fifth reuse. The study provides a promising route for the proper disposal and resource utilization of OBDS and OBDCs and proposes a novel biochar compound as an electrode for the efficient treatment of wastewater. Moreover, this work highlights the important significance of the simultaneous resource utilization of waste and the treatment of wastewater using waste materials.

Adsorption characteristics of magnetized biochar derived from Citrus limetta peels

Agro-industrial waste is an alarming issue that needs to be addressed. Waste valorization is an effective technique to deal with such effectively. Synthesis of biochar from fruit waste is one of the emerging approaches for adsorption, energy storage, air purification, catalysis, and biogas production trending these days. Magnetized Citrus limetta biochar (MCLB) was synthesized from Citrus limetta peels and was magnetized using iron oxide. Magnetization of biochar increases its functionalities as well as makes its separation easy. The removal of Methylene Blue (MB) dye from an aqueous solution is achieved through the use of MCLB. Methylene Blue is a prominent and widely used cationic-azo dye in the textile and printing industries. The accumulation of MB in wastewater is the major problem as MB is reported as a carcinogenic agent. The removal of MB dye with MCLB was analyzed by adsorption studies, wherein the effect of factors influencing adsorption such as initial concentration of MB dye, MCLB dosage, the effect of pH, contact time, and adsorption isotherms were studied. Characterization of MCLB was carried out using various techniques, such as FTIR, VSM, XRD, SEM, RAMAN, and Zeta potential. The adsorption isotherm mechanism was well explained with the non-linear Langmuir isotherm model resulting in a good adsorption capacity (q e  = 41.57 mg/g) of MCLB when MB (co = 60 mg/L, pH ~ 6.8, T = 273K). The thermodynamics analysis revealed that MB's spontaneous and endothermic adsorption onto the MCLB surface followed pseudo-second-order kinetics. The results obtained from this study suggest that the magnetized biochar derived from Citrus limetta peels has a wide range of potential applications in the treatment of dyeing wastewater.

Multifunctional 3D magnetic carbon aerogel for adsorption separation and highly sensitive SERS detection of malachite green

This work presents a novel strategy for the synthesis of a recyclable aerogel and its multifunctional application as effective adsorption material for organic pollutants and as a high-quality SERS substrate for on-site detection measurement. Silver nanoparticles (Ag NPs) were uniformly dispersed and adsorbed on the surface of an Fe3C-loaded carbon aerogel, resulting in the formation of a three-dimensional Ag-Fe3C-MCA (magnetic carbon aerogel) composite. The substrate preparation led to Ag-Fe3C-MCA with a mesoporous structure for high adsorption capacity, together with magnetic properties for easy separation capability. The Ag-Fe3C-MCA composite demonstrated an efficient removal ability for malachite green (MG), with an adsorption capacity of 296.7 mg g-1. Moreover, Ag-Fe3C-MCA composite provided ultrasensitive surface-enhanced Raman scattering detection for MG molecules, obtaining a limit of detection (LOD) of 3 × 10-10 M. Aquaculture water samples with spiked MG concentrations were used to simulate practical scenarios. The Ag-Fe3C-MCA presented has a significant potential for the removal of hazardous residues in wastewater, together with an efficient and sensitive method of quantification, all on the same substrate.

Adsorption properties of hollow carbon spheres to gaseous cyclohexane using DFT simulation and experiments

The cyclohexane is the common toxic volatiles emitted from the various industry in worldwide leading to environmental degradation and human illnesses. Hence, there is a requirement for an efficient and stable adsorbent for adsorbing these toxic molecules to safeguard human health and the air atmosphere. Hollow carbon spheres (HCS) are a new type of carbon nanomaterial with large specific surface area, low density, and good chemical and thermal stability. In this study, DFT simulations and static-dynamic adsorption studies of cyclohexane were carried out using HCS as the adsorbent material. Among them, static adsorption focuses on adsorption/desorption isotherm, adsorption isotherm model fitting and isosteric heat of adsorption. Dynamic adsorption was mainly studied the effect of initial concentrations, gas flow rate, and ambient temperature on adsorption performance. The results showed that HCS exhibited very good performance in cyclohexane adsorption.

Degradation performance of methylene blue in metal nanoparticle modified 3D mesoporous wood microchannels

Wood has a rich three-dimensional pore structure and many bottom-up nanochannels. However, the structure of wood itself has limited ability to adsorb dyes, so the effective combination of the unique structure of wood and Pd NPs was studied to achieve efficient degradation of dyes. First, the three-dimensional structure of natural wood is optimized by combining the complex pore structure of wood with Pd NPs to improve the contact process between the dye and Pd NPs. Then, Pd (II) ion can be well reduced to Pd NPs by wood lignin. In addition, Pd NPs can be fixed by hydroxyl groups on cellulose in wood. The flow state inside Pd NPs/wood film and the contact area between catalyst and dye were discussed in detail by hydrodynamic simulation, which filled the gap. It provides reference for composite structure. When Pd NPs/wood membrane was used to treat methylene blue (MB), the degradation efficiency was up to 96.7%, which was 90% higher than that of natural wood. Its TOF value was 1.82 molMB molPd-1min-1, which was higher than that in the previous literature. Therefore, the novelty of this study is that the mechanism of catalytic degradation of MB by Pd nanoparticles/wood composites is reported for the first time. The internal flow mode and contact condition of the new material are understood, which has a good application prospect.

Characterization and Adsorption Capacity of Modified Biochar for Sulfamethylimidine and Methylene Blue in Water

In this study, a composite of pond mud and lanthanum- and nano-zero valent iron-modified-biochar was investigated for its ability to adsorb methylene blue (MB) and sulfamethazine (SMZ). La-modified attapulgite and nano-zero valent iron (surface area enhanced by 43.7% via Brunauer-Emmett-Teller analysis) were successfully loaded onto the straw-sediment biochar (BC) surface. With the increase in pyrolysis temperature, the biocompatibility yield, the H, O, and N content, and the ratio of carbon elements decreased, while the pH value, surficial micropores, C element, and ash content increased. The biocarbon small molecules were gradually and tightly ordered, and the organic groups such as hydroxyl, carboxyl groups, and carbon oxygen double bonds were gradually lost or disappeared. The original Fe-BC had more phenolic hydroxyl groups forming an intermolecular hydrogen bond than others with a higher adsorption capacity possibly through the Schiff base reaction. The effect of various pH (2-9), temperature (15-35 °C), and initial concentration (1-25 mg L-1) on adsorption was investigated. pH and temperature were the main factors governing the adsorption process. The maximum adsorption capacity was observed at pH 4. The adsorption performances for MB followed the order Fe-BC > La-BC > BC, and the maximum removal rate was over 98.45% with pH = 7. The three types of BC dosages between 0.2 (6.67 g L-1) and 0.4 g showed a removal rate of 99% for MB. The adsorption capacity of Fe-BC, La-BC, and BC for MB was 2.201, 1.905, and 2.401 mg L-1 with pH = 4, while 4.79, 4.58, and 5.55 mg g-1 were observed with BC dosage at 0.025 g. For SMZ, the higher the temperature, the better the adsorption effect, and it reaches saturation at approximately 25 °C. To further evaluate the nature of adsorption, Langmuir/Freundlich/Temkin models were tested and the adsorption capacities were evaluated on the surface of the BC composite. The three modified materials were physisorbed to SMZ, while MB was chemisorbed. For MB, the adsorption performance of BC is the best < 0.2 g (6.67 g L-1) at pH 7.0 at 35 °C. The Elovich model was more suitable for MB, while the Freundlich and Temkin models could better fit the adsorption process of MB. The preparatory secondary dynamics equation and Langmuir equation were more compliant for SMZ, and the saturated adsorption capacities of straw-modified, La-BC, and Fe-BC reached 5.699, 6.088, and 5.678 mg L-1, respectively.

Removal of methylene blue by porous biochar obtained by KOH activation from bamboo biochar

A series of activated biochar (KBBC-700, KBBC-800 and KBBC-900) which were modified by KOH and pyrolysis at various temperatures from ball-milling bamboo powder were obtained. The physicochemical properties and pore structures of activated biochar were investigated by scanning electron microscopy (SEM), fourier transform infrared spectoscopy (FT-IR), X-ray diffraction (XRD) and N2 adsorption/desorption. The adsorption performance for the removal of methylene blue (MB) was deeply studied. The results showed that KBBC-900 obtained at activation temperature of 900 °C exhibited a great surface area which reached 562 m2/g with 0.460 cm3/g of total pore volume. The enhancement of adsorption capacity could be ascribed to the increase of surface oxygen-containing functional groups, aromatization and mesoporous channels. The adsorption capacity was up to 67.46 mg/g under the optimum adsorption parameters with 2 g/L of adsorbent dose, 11 of initial solution pH and 298 K of the reactive temperature. The adsorption capacity was 70.63% of the first time after the material was recycled for three cycles. The kinetics indicated that the adsorption equilibrium time for MB on KBBC-900 was of about 20 min with the data fitted better to the pseudo-second-order kinetics model. The adsorption process was mainly dominated by chemical adsorption. Meanwhile, the adsorption isotherm showed that the Langmuir model fitted the best, and thermodynamic parameters revealed that the adsorption reaction was the endothermic nature and the spontaneous process. Adsorption of MB mainly attributed to electrostatic interactions, cation-π electron interaction and redox reaction. This study suggested that the activated biochar obtained by KOH activation from bamboo biochar has great potentials in the practical application to remove MB from wastewater.

An Electrochemical Sensor Based on a Porous Biochar/Cuprous Oxide (BC/Cu2O) Composite for the Determination of Hg(II)

Mercuric ion (Hg²⁺) in aqueous media is extremely toxic to the environment and organisms. Therefore, the ultra-trace electrochemical determination of Hg²⁺ in the environment is of critical importance. In this work, a new electrochemical Hg²⁺ sensing platform based on porous activated carbon (BC/Cu₂O) modified with cuprous oxide was developed using a simple impregnation pyrolysis method. Differential pulse anodic stripping voltammetry (DPASV) was used to investigate the sensing capability of the BC/Cu₂O electrode towards Hg²⁺. Due to the excellent conductivity and large specific surface area of BC, and the excellent catalytic activity of Cu₂O nanoparticles, the prepared BC/Cu₂O electrode exhibited excellent electrochemical activity. The high sensitivity of the proposed system resulted in a low detection limit of 0.3 ng·L^-1 and a wide linear response in the ranges from 1.0 ng·L^-1 to 1.0 mg·L^-1. In addition, this sensor was found to have good accuracy, acceptable precision, and reproducibility. All of these results show that the BC/Cu₂O composite is a promising material for Hg²⁺ electrochemical detection.

Improving adsorption performance of L-ascorbic acid from aqueous solution using magnetic rice husk as an adsorbent: experimental and RSM modeling

In this research, rice husk (RH) was utilized to prepare a magnetic adsorbent for adsorption of ascorbic acid (AA). The magnetic agent is iron(III) chloride (FeCl₃). The impact of acid concentration in the range of 400-800 ppm, adsorbent dosage in the range of 0.5-1 g, and contact time in the range of 10-130 min were studied. The Langmuir model had the highest R² of 0.9982, 0.9996, and 0.9985 at the temperature of 15, 25, and 35 °C, respectively, and the q_max values in these temperatures have been calculated at 19.157, 31.34, and 38.75 mg/g, respectively. The pseudo-second-order kinetic model had the best agreement with the experimental results. In this kinetic model, the values of q have been measured at 36.496, 45.248, and 49.019 mg/g at the acid concentration of 418, 600, and 718 ppm, respectively. The values of ΔH^o and ΔS^o were measured 31.972 kJ/mol and 120.253 kJ/mol K, respectively, which proves the endothermic and irregularity nature of the adsorption of AA. Besides, the optimum conditions of the design-expert software have been obtained 486.929 ppm of acid concentration, 0.875 g of the adsorbent dosage, and 105.397 min of the contact time, and the adsorption efficiency in these conditions was determined at 92.94%. The surface area of the RH and modified RH was determined of 98.17 and 120.23 m²/g, respectively, which confirms the high surface area of these two adsorbents.

Adsorption properties and mechanisms of methylene blue and tetracycline by nano-silica biochar composites activated by KOH

Dyestuff wastewater and pharmaceutical wastewater have become typical representatives of water pollution. In this study, a novel nano-silica-biochar composite (NSBC) was synthesized based on corn straw as raw material, by a combination of ball milling, pyrolysis and KOH activation. The modified biochar with rough surface had higher specific surface area (117.67-132.82 m²/g), developed pore structure (0.12-0.15 cm³/g) and abundant surface functional groups (-OH, -COOH, Si-O and aromatic CC were dominated). These provided abundant active sites for the adsorption of pollutants. The adsorption capacities of NSBC for Methylene Blue (MB) and Tetracycline (TC) were both higher than that of other similar products, the maximum adsorption capacity of Langmuir were 247.22 and 86.95 mg/g, respectively. After five adsorption-desorption cycle experiments, the adsorption capacities of NSBC for both were still excellent, reaching 99.30 and 19.87 mg/g, respectively. Due to the different structure and molecular size of MB and TC, the adsorption capacities of NSBC were significantly different, especially the influence of solution pH value. The adsorption mechanisms were comprehensively discussed by FTIR and XPS of the samples before and after adsorption, and combining experimental results of BET and simultaneously, which were manifested as monolayer chemisorption, specifically surface complexation, hydrogen bonding, n-π/π-π conjugation, electrostatic interaction and pore filling.

Qualitative and quantitative analysis for Cd2+ removal mechanisms by biochar composites from co-pyrolysis of corn straw and fly ash

Removal of heavy metals (e.g., Cd) from contaminated water using waste-converted adsorbents is promising, but the efficiency still needs to be improved. Here, we prepared a functional biochar composite as novel Cd adsorbents by co-pyrolysis of two typical solid wastes, i.e., agricultural corn straw and industrial fly ash. The adsorption behavior and mechanism were investigated using batch and column adsorption experiments and modern characterization techniques. Results showed that alkali-modified fly ash (AMFA) was loaded onto the surface of the corn straw biochar as some fine particle forms, with quartz (SiO₂) and silicate being the main mineral phases on the surface. The maximum sorption capacity fitted by Langmuir model for functionalized biochar composite (FBC700) was up to 137.1 mg g^-1, which was 7.7 times higher than that of the original corn straw biochar (BC700). Spectroscopic analysis revealed that adsorption mechanisms of Cd onto the FBC700 included mainly precipitation and ion exchange, with complexation and Cd-π interaction also contributing. The AMFA could effectively improve the mineral precipitation with Cd. The adsorption columns filled with FBC700 exhibited a longer breakthrough time than that filled with BC700. The adsorption capacity calculated by Thomas model for FBC700 was also approximately 6.0 times higher than that for BC700, showing that FBC700 was more suited to practical applications. This study provided a novel perspective for recycling solid wastes and treating Cd-contaminated water.

Optimization of pig manure-derived biochar for ammonium and phosphate simultaneous recovery from livestock wastewater

Livestock wastewater has led to serious eco-environmental issues. To effectively treat livestock wastewater and realize the resource utilization of livestock solid waste, manure waste has been widely used to prepare biochar for the recovery of nitrogen and phosphorus. However, fresh biochar has a poor ability to adsorb phosphate due to its negative charge. To overcome the defect, the proportion of biochar samples prepared at 400 °C and 700 °C was optimized under a mass ratio of 2:3 to obtain mixed biochar PM 4-7, achieving the purpose of enhanced ammonium and phosphate recovery in livestock wastewater simultaneously without any modification. The effects of pyrolysis temperature, dosage, and pH were studied, different adsorption models were used to explore the adsorption mechanism, and the effect of biochar loaded with nutrient elements on seed was verified through a seed germination experiment. It was revealed that the maximum removal rates of phosphate and ammonium were 33.88 % and 41.50 %, respectively, endorsing that mixed biochar PM 4-7 can recover nutrients from livestock wastewater, and could be used as a slow-release fertilizer to promote seed germination and growth. This method provides a new potential way for the efficient resource utilization of pig manure and the recovery of nutrients from breeding wastewater.

Simultaneously Cationic and Anionic Dyes Elimination via Magnetic Hydrochar Prepared from Copper Slag and Pinewood Sawdust

In practical wastewater, cationic and anionic dyes usually coexist, while synergistic removal of these pollutants is difficult due to their relatively opposite properties. In this work, copper slag (CS) modified hydrochar (CSHC) was designed as functional material by the one-pot method. Based on characterizations, the Fe species in CS can be converted to zero-valent iron and loaded onto a hydrochar substrate. The CSHC exhibited efficient removal rates for both cationic dyes (methylene blue, MB) and anionic dyes (methyl orange, MO), with a maximum capacity of 278.21 and 357.02 mg·g^-1, respectively, which was significantly higher than that of unmodified ones. The surface interactions of MB and MO between CSHC were mimicked by the Langmuir model and the pseudo-second-order model. In addition, the magnetic properties of CSHC were also observed, and the good magnetic properties enabled the adsorbent to be quickly separated from the solution with the help of magnets. The adsorption mechanisms include pore filling, complexation, precipitation, and electrostatic attraction. Moreover, the recycling experiments demonstrated the potential regenerative performance of CSHC. All these results shed light on the co-removal of cationic and anionic contaminates via these industrial by-products derived from environmental remediation materials.

Iron oxide nanoparticles/nanocomposites derived from steel and iron wastes for water treatment: A review

Iron oxide nanoparticles (IONPs) are characterized by superior magnetic properties, high surface area to volume ratio, and active surface functional groups. These properties aid in removal of pollutants from water, through adsorption and/or photocatalysis, justifying the choice of IONPs in water treatment systems. IONPs are usually developed from commercial chemicals of ferric and ferrous salts alongside other reagents, a procedure that is costly, environmentally unfriendly and limits their mass production. On the other hand, steel and iron industries produce both solid and liquid wastes which in most cases are piled, discharged into water streams or landfilled as strategies to dispose them off. Such practices are detrimental to environmental ecosystems. Given the high content of iron present in these wastes, they can be used to generate IONPs. This work reviewed published literature through selected key words on the deployment of steel and/or iron-based wastes as IONPs precursors for water treatment. The findings reveal that steel waste-derived IONPs have properties such as specific surface area, particle sizes, saturation magnetization, and surface functional groups that are comparable or sometimes better than those synthesized from commercial salts. Furthermore, the steel waste-derived IONPs have high removal efficacy for heavy metals and dyes from water with possibilities of being regenerated. The performance of steel waste-derived IONPs can be enhanced by functionalization with different reagents such as chitosan, graphene, and biomass based activated carbons. Nonetheless, there is need to explore the potential of steel waste-based IONPs in removing contaminants of emerging concern, modifying pollutant detection sensors, their techno-economic feasibility in large treatment plants, toxicity of these nanoparticles when ingested into the human body, among other areas.

Assessment of the properties of aging biochar used as a substrate in constructed wetlands

Biochar has gained global recognition as an effective tool for environmental remediation, and is increasingly being used as an alternative substrate in constructed wetlands (CWs). While, most studies have focused on the positive effects of biochar for the pollutant removal in CWs, less is known about aging and longevity of the embedded biochar. This study investigated the aging and stability of biochar embedded in CWs post-treating the effluent of a municipal and an industrial wastewater treatment plant. Litter bags containing biochar were inserted into two aerated horizontal subsurface flow CWs (350 m² each), and retrieved on several dates (8-775 days after burial) for assessment of weight loss/gain and changes in biochar characteristics. Additionally, a 525-day laboratory incubation test was conducted to analyze biochar mineralization. The results showed that there was no significant biochar weight loss over time, but a slight increase in weight (2.3-3.0%) was observed at the end, likely due to mineral sorption. Biochar pH remained stable except for a sudden drop at the beginning (8.6-8.1), while the electrical conductivity continued to increase (96-256 μS cm^-1) throughout the experiment. The sorption capacity of the aged biochar for methylene blue significantly increased (1.0-1.7 mg g^-1), and a change in the biochar's elemental composition was also noted, with O-content increasing by 13-61% and C content decreasing by 4-7%. Despite these changes, the biochar remained stable according to the criteria of the European Biochar Foundation and International Biochar Initiative. The incubation test also showed negligible biochar mass loss (<0.02%), further validating the stability of the biochar. This study provides important insights into the evolution of biochar characteristics in CWs.

Efficient removal of Cr(VI) and As(V) from an aquatic system using iron oxide supported typha biochar

The removal of Cr(VI) and As(V) from aqueous solutions has been a worldwide concern. In this study, Typha biochar (FBC) with magnetic iron oxide was prepared by impregnating Typha with FeCl₃ and performing pyrolysis, and the possible mechanism of Cr(VI) and As(V) removal was investigated by combining characterization means and adsorption experiments. The results showed that the modified Typha biochar is rich in pores and has the potential to eliminate Cr and As through processes such as exchange and reduction. The single molecule uptake capacities of FBC for Cr(VI) and As(V) were 32.82 and 21.56 mg g^-1, respectively. The adsorption process is spontaneous heat absorption, and the adsorption results are also consistent with the proposed secondary kinetic model. FBC still had >60% removal efficiency in the second and third reuse of Cr(VI), indicating its good recyclability. Therefore, this study confirms that FBC can effectively remove both Cr(VI) and As(V).

Bio-inspired sustainable synthesis of novel SnS2/biochar nanocomposite for adsorption coupled photodegradation of amoxicillin and congo red: Effects of reaction parameters, and water matrices

This study aims to fabricate a novel integrated photocatalytic adsorbent (IPA) via a green solvothermal process employing tea (Camellia sinensis var. assamica) leaf extract as a stabilizing and capping agent for the removal of organic pollutants from wastewater. An n-type semiconductor photocatalyst, SnS_2, was chosen as a photocatalyst due to its remarkable photocatalytic activity supported over areca nut (Areca catechu) biochar for the adsorption of pollutants. The adsorption and photocatalytic properties of fabricated IPA were examined by taking amoxicillin (AM) and congo red (CR) as two emerging pollutants found in wastewater. Investigating synergistic adsorption and photocatalytic properties under varying reaction conditions mimicking actual wastewater conditions marks the novelty of the present research. The support of biochar for the SnS₂ thin films induced a reduction in charge recombination rate, which enhanced the photocatalytic activity of the material. The adsorption data were in accordance with the Langmuir nonlinear isotherm model, indicating monolayer chemosorption with the pseudo-second-order rate kinetics. The photodegradation process follows pseudo-first-order kinetics with the highest rate constant of 0.0450 min^-1 for AM and 0.0454 min^-1 for CR. The overall removal efficiency of 93.72 ± 1.19% and 98.43 ± 1.53% could be achieved within 90 min for AM and CR via simultaneous adsorption and photodegradation model. A plausible mechanism of synergistic adsorption and photodegradation of pollutants is also presented. The effect of pH, Humic acid (HA) concentration, inorganic salts and water matrices have also been included.The photodegradation activity of SnS₂ under visible light coupled with the adsorption capability of the biochar results in the excellent removal of the contaminants from the liquid phase.

A novel green synthesized magnetic biochar from white tea residue for the removal of Pb(II) and Cd(II) from aqueous solution: Regeneration and sorption mechanism

A novel biochar-based magnetic nanocomposite (GSMB) was prepared from white tea waste via green synthesis method. The sorption properties and regeneration of GSMB were studied using Pb(II) and Cd(II) to better understand its ability in heavy metal recovery. The adsorption kinetics data were modelled using pseudo-first order, pseudo-second order, Elovich and intraparticle diffusion models, while Pb(II) and Cd(II) isotherms were modelled with Langmuir, Freundlich, Temkin and Dubinin-Radushkevich models. Results showed that Pb(II) adsorption was well described by pseudo-second order while the Elovich model best described the Cd(II) adsorption trend, indicating the sorption of Pb(II) and Cd(II) onto GSMB were dominated by chemisoprtion than physisorption. Langmuir model gave the best fit to Pb(II) sorption, and the Cd(II) adsorption was well described by Temkin model. The maximum adsorption capacity of Pb(II) and Cd(II) onto GSMB were 81.6 mg/g and 38.6 mg/g, respectively. Scanning electron microscope coupled with energy dispersive x-ray, X-ray diffraction and Fourier transform infrared spectroscopy analyses revealed that iron oxides played a key role during adsorption process and the adsorption mechanisms include surface electrostatic attraction and surface complexation for both metals. Among the five regenerating agents studied, 0.1 M EDTA-2Na was favoured for the desorption of Pb(II) onto GMSB. The findings from the regeneration studies revealed ∼54% of Pb(II) adsorption capacity was remained after three sorption-desorption cycles implying the adsorbent could potentially be further reused.

Enhanced selective separation of vanadium(V) and chromium(VI) using the CeO2 nanorod containing oxygen vacancies

Adsorption of vanadium from wastewater defends the environment from toxic ions and contributes to recover the valuable metal. However, it is still challenging for the separation of vanadium (V⁵⁺) and chromium (Cr⁶⁺) because of their similar properties. Herein, a kind of CeO₂ nanorod containing oxygen vacancies is facilely synthesized which displays ultra-high selectivity of V⁵⁺ against various competitive ions (i.e., Fe, Mn, Cr, Ni, Cu, Zn, Ga, Cd, Ba, Pb, Mg, Be, and Co). Moreover, a large separation factor (SF_V/Cr) of 114,169.14 for the selectivity of V⁵⁺ is achieved at the Cr⁶⁺/V⁵⁺ ratio of 80 with the trace amount of V⁵⁺ (~ 1 mg/L). The results show that the process of V⁵⁺ uptake is the monolayer homogeneous adsorption and is controlled by external and intraparticle diffusions. In addition, it also shows that V⁵⁺ is reduced to V³⁺ and V⁴⁺ and then formation of V-O complexation. This work offers a novel CeO₂ nanorod material for efficient separation of V⁵⁺ and Cr⁶⁺ and also clarifies the mechanism of the V⁵⁺ adsorption on the CeO₂ surface.

Sustainable green conversion of coal gangue waste into cost-effective porous multimetallic silicate adsorbent enables superefficient removal of Cd(II) and dye

Converting solid wastes into new materials for wastewater decontamination is a feasible "one stone, three birds" strategy to achieve sustainable value-added utilization of resources and minimize waste emissions, but significant challenges remain. In response to this, we proposed an efficient "mineral gene reconstruction" method to synchronously transform coal gangue (CG) into a green porous silicate adsorbent without using any harmful chemicals (i.e., surfactants, organic solvents). The one of the synthesized adsorbents with a high specific surface area (582.28 m²/g) and multimetallic active centres shows outstanding adsorption performance (adsorption capacities: 168.92 mg/g for Cd(II), 234.19 mg/g for methylene blue (MB); removal rate: 99.04% for Cd(II) and 99.9% for MB). The adsorbent can also reach a high removal rate of 99.05%∼99.46% and 89.23%∼99.32% for MB and Cd(II) in real water samples (i.e., Yangtze River, Yellow River, seawater and tap water), respectively. After 5 adsorption-desorption cycles, the adsorption efficiency remained above 90%. The adsorbents mainly adsorbed Cd(II) by electrostatic attraction, surface complexation and partial ion exchange and MB by electrostatic and hydrogen bonding interactions. This study provides a sustainable and promising platform for developing a new-generation cost-efficient adsorbent from waste for clean water production.

Efficient removal of phytochrome using rice straw-derived biochar: Adsorption performance, mechanisms, and practical applications

Rice straw derived biochar was fabricated and applied as a purification agent. The adsorption kinetics, isotherms, and thermodynamics for adsorbates were determined using the biochar. Adsorption kinetics and isotherms were best fitted by the pseudo-second order and Langmuir models. Biochar could effectively remove chlorophyll in 9 different solutions. Biochar was employed as a clean-up reagent for 149 pesticides detection, which revealed that biochar had a higher phytochrome removal capacity than graphitized carbon black and 123 pesticides had satisfactory recovery values. The biochar was prepared into a sample pad by electrospinning and was then used for online sample clean-up in a test strip, and it showed high ability of removing phytochrome and improving detection sensitivity. Thus, biochar could be applied as a purification agent to remove pigmentation, making it a promising candidate not only for sample pretreatment but also in the fields of food, agriculture and environment.

The mechanism of water pollutant photodegradation by mixed and core-shell WO3/TiO2 nanocomposites

Environmental pollution is one of the biggest concerns in the world today, and solar energy-driven photocatalysis is a promising method for decomposing pollutants in aqueous systems. In this study, the photocatalytic efficiency and catalytic mechanism of WO₃-loaded TiO₂ nanocomposites of various structures were analyzed. The nanocomposites were synthesized via sol-gel reactions using mixtures of precursors at various ratios (5%, 8%, and 10 wt% WO₃ in the nanocomposites) and via core-shell approaches (TiO₂@WO₃ and WO₃@TiO₂ in a 9 : 1 ratio of TiO₂ : WO₃). After calcination at 450 °C, the nanocomposites were characterized and used as photocatalysts. The kinetics of photocatalysis with these nanocomposites for the degradation of methylene blue (MB⁺) and methyl orange (MO^-) under UV light (365 nm) were analyzed as pseudo-first-order reactions. The decomposition rate of MB⁺ was much higher than that of MO^-, and the adsorption behavior of the dyes in the dark suggested that the negatively charged surface of WO₃ played an important role in adsorbing the cationic dye. Scavengers were used to quench the active species (superoxide, hole, and hydroxyl radicals), and the results indicated that hydroxyl radicals were the most active species; however, the active species were generated more evenly on the mixed surfaces of WO₃ and TiO₂ than on the core-shell structures. This finding shows that the photoreaction mechanisms could be controlled through adjustments to the nanocomposite structure. These results can guide the design and preparation of photocatalysts with improved and controlled activities for environmental remediation.

Treatment of hazardous landfill leachate containing 1,4 dioxane by biochar-based photocatalysts in a solar photo-oxidation reactor

This study investigates a combined photocatalytic and adsorption system to maximize the removal of 1,4 dioxane from hazardous landfill leachate (HLL). The production of transformation products was also investigated to obtain a comprehensive evaluation of the treatment system. Copper/iron doped zinc oxide (Cu-Fe-ZnO) was introduced to biochar to form a hybrid materials and used to treat HLL contaminated with 1,4 dioxane of 355.0 ± 11.7 mg/L. The Cu-Fe-ZnO/biochar removed 93.1 ± 8.7% of 1,4 dioxane at a dose of 0.6 g/L within 90 min, as compared with only 42.7 ± 3.3% by 1.2 g/L of bare biochar within 210 min. The Cu-Fe-ZnO/biochar degraded 1,4 dioxane into ethylene glycol, glycolic acid, and formic acid. The 1,4 dioxane removal mechanisms were investigated using the density functional theory, demonstrating that doping of ZnO with metal atoms (Cu-Fe) narrowed the bandgap from 3.307 eV to 2.736 eV. The enhanced photocatalytic activity of ZnO was also supported by the role of biochar in increasing the reactive species and adsorbing the pollutant molecules. The high degradation efficiency of 1,4 dioxane using small catalyst doses with short reaction times would reduce the treatment cost and improve the system's applicability for treating HLL and industrial effluents.

A comprehensive review on the metal-based green valorized nanocomposite for the remediation of emerging colored organic waste

In today's era, "green" synthesis is an emerging research trend. It has gained widespread attention owing to its dynamic behavior, reliability, simplicity, sustainability, and environment friendly approach for fabricating various nanomaterials. Green fabrication of metal/metal oxides nanomaterials, hybrid materials, and other metal-based nanocomposite can be utilized to remove toxic colored aqueous pollutants. Nanomaterials synthesized by using green approach is considered to be the significant tool to minimize unwanted or harmful by-products otherwise released from traditional synthesis methods. Various kinds of biosynthesized nanomaterials, such as animal waste and plant-based, have been successfully applied and well documented in the literature. However, their application part, especially for the cure of colored organic polluted water, has not been reported as a single review article. Therefore, the current work aims to assemble reports on using novel biosynthesized green metal-based nanomaterials to exclude harmful dyes from polluted water.

Effective removal of methylene blue with zero-valent iron/tea residual biochar composite: Performance and mechanism

Zero-valent iron (Fe⁰)-modified biochar (BFN) was prepared via low-temperature pyrolysis of tea residue (TR) and ferric nitrate hexahydrate (FN) coupled with NaOH activation for the removal of methylene blue (MB). BFN exhibited a specific surface area of 382.66 m²·g^-1, an average pore diameter of 4.97 nm and an equilibrium adsorption capacity as high as 452.5 mg·g^-1 of 0.33 g·L^-1 toward 150 mg·L^-1 MB within 60 min at 30 °C and pH 7.0. The recovered MB is far below of the removal rate in each of adsorption-desorption cycle because the removal mechanism is that MB molecular was firstly chemically adsorbed, then it was reduced and mineralized by BFN with the formation of nitrate, sulfate, CO₂ and H₂O.

Twice-milled magnetic biochar: A recyclable material for efficient removal of methylene blue from wastewater

Although magnetic modification has potential for preparing recyclable biochar, the traditional preparation methods of loading magnetic materials on biochar will probably lead to pore blockage and consequently remarkable adsorption recession. Herein, a preparation method was developed in which ball milled biochar was loaded with ultrafine magnetite and then milled for a second time, thus generating a magnetic, recyclable biochar with minimal pore blockage. The deposits of magnetite did not significantly wrap the biochar, although a decreased sorption performance was still detectable. Benefitting from the extra milling step, surface functional groups and specific surface areas of the adsorbents were largely restored, thus leading to a 93.8 % recovery adsorption of 84.6 ± 2.5 mg/L on methylene blue. Meanwhile, the recyclability of the material was not affected. The adsorption was driven by multiple interactions. These twice-milled magnetic biochar is quite outstanding for sustainable removal of aqueous contaminants with its recyclability and high sorption efficiency.