Biochar-facilitated remediation of nanoplastic contaminated water: Effect of pyrolysis temperature induced surface modifications

Polyvinyl chloride nanoplastics transport inhibited in natural sandy soil by iron-modified biochar

The small particle size of nanoplastics allows them to migrate through soil and make them highly bioavailable, posing a potential threat to groundwater. Measures are urgently needed to reduce the migration of nanoplastics in soil. However, there is limited research available on this topic. In this study, two types of iron-modified biochar (magnetic corncob biochar (MCCBC) and magnetic walnut shell biochar (MWSBC)) were selected and their effects on the transport of polyvinyl chloride nanoplastics (PVC-NPs) in natural sandy soil columns under different ionic types and strengths were investigated. The results show that the transport of PVC-NPs in single sandy soil columns was rapid and efficient, with the estimated breakthrough rate of 85.10%. However, the presence of MCCBC and MWSBC (0.5%, w/w) significantly inhibited the transport of PVC-NPs in sandy soil columns (p < 0.05), and MCCBC had a stronger inhibitory effect on the transport of PVC-NPs than MWSBC. This can be attributed to the fact that the adsorption of PVC-NPs on adsorbents followed the order as: MCCBC > MWSBC > sandy soil. The retention of PVC-NPs by MCCBC and MWSBC is determined by ionic type and ionic strength. The presence of coexisting ions enhanced the inhibitory effect of iron-modified biochar on the transport of PVC-NPs, with the following order: Ca2+  > SO2- 4 > Cl- > NO- 3. The inhibitory effect of MCCBC and MWSBC on the transport of PVC-NPs in soil columns increased with increasing ionic strengths. Furthermore, MCCBC and MWSBC inhibited the migration of PVC-NPs in a rainwater-soil system. The mechanisms by which MCCBC and MWSBC affect the transport of PVC-NPs in soil columns were considered to enhancing adsorption and decreasing soil pore volume. The results provide new insights into the management of soil nanoplastic pollution.

Enhanced sinks of polystyrene nanoplastics (PSNPs) in marine sediment compared to freshwater sediment: Influencing factors and mechanisms

The difference in the transport behaviors of nanoplastics consistently assistant with their toxicities to benthic and other aquatic organisms is still unclear between freshwater and marine sediments. Here, the mobilities of polystyrene nanoplastics (PSNPs) and key environmental factors including salinity and humic acid (HA) were systematically studied. In the sand column experiments, both tested PSNPs in the freshwater system (100 nm NPs (100NPs): 90.15 %; 500 nm NPs (500NPs): 54.22 %) presented much higher penetration ratio than in the marine system (100NPs: 8.09 %; 500NPs: 19.04 %). The addition of marine sediment with a smaller median grain diameter caused a much more apparent decline in NPs mobility (100NPs: from 8.09 % to 1.85 %; 500NPs: from 19.04 % to 3.51 %) than that containing freshwater sediment (100NPs: from 90.15 % to 83.56 %; 500NPs: from 54.22 % to 41.63 %). Interestingly, adding HA obviously led to decreased and slightly increased mobilities for NPs in freshwater systems, but dramatically improved performance for NPs in marine systems. Electrostatic and steric repulsions, corresponding to alteration of zeta potential and hydrodynamic diameter of NPs and sands, as well as minerals owing to adsorption of dissolved organic matter (DOM) and aggregations from varied salinity, are responsible for the mobility difference.

Monitoring Poly(methyl methacrylate) and Polyvinyl Dichloride Micro/Nanoplastics in Water by Direct Solid-Phase Microextraction Coupled to Gas Chromatography-Mass Spectrometry

A simple, sustainable, and sensitive monitoring approach of micro/nanoplastics (MNPs) in aqueous samples is crucial since it helps in assessing the extent of contamination and understanding the potential risks associated with their presence without causing additional stress to the environment. In this study, a novel strategy for qualitative and quantitative determination of MNPs in water by direct solid-phase microextraction (SPME) coupled with gas chromatography-mass spectrometry (GC-MS) was proposed for the first time. Spherical poly(methyl methacrylate) (PMMA) and irregularly shaped polyvinyl dichloride (PVDC) were used to evaluate the feasibility and performance of the proposed method. The results demonstrated that both PMMA and PVDC MNPs were efficiently extracted by the homemade SPME coating of nitrogen-doped porous carbons (N-SPCs) and exhibited sufficient thermal decomposition in the GC-MS injection port. Excellent extraction performances of N-SPCs coating for MNPs are attributed to hydrophobic cross-linking, electrostatic forcing, hydrogen bonding, and pore trapping. Methyl methacrylate was identified as the marker for PMMA, while 1,3-dichlorobenzene and 1,3,5-trichlorobenzene were the indicators for PVDC. Under the optimal extraction and decomposition conditions, the proposed method exhibited ultrahigh sensitivity, with a limit of detection of 0.0041 μg/L for PMMA and 0.0054 μg/L for PVDC. Notably, a programmed temperature strategy for the GC-MS injector was developed to discriminate and eliminate the potential interferences of intrinsic indicator compounds. Owing to the integration of sampling, extraction, injection, and decomposition into one step by SPME, the proposed method demonstrates exceptional sensitivity, eliminating the necessity for complex sample pretreatment procedures and the use of organic solvents. Finally, the proposed method was successfully applied in the determination of PMMA and PVDC MNPs in real aqueous samples.

Assessment and accumulation of microplastics in the Indian riverine systems: Risk assessment and implications of translocation across the water-to-fish continuum

Microplastic (MP) pollution has engulfed global aquatic systems, and the concerns about microplastic translocation and bioaccumulation in fish and other aquatic organisms are now an unpleasant truth. In the past few years, MP pollution in freshwater systems, particularly rivers and subsequently in freshwater organisms, especially in fish, has caught the attention of researchers. Rivers provide livelihood to approximately 40 % of the global population through food and potable water. Hence, assessment of emerging contaminants like microplastics in rivers and the associated fauna is crucial. This study assessed microplastics (MPs) in fish, sediment and freshwater samples across the third largest riverine system of peninsular India, the Mahanadi River. The number concentrations of MPs measured in water, sediment and fish ranged from 337.5 ± 54.4-1333.3 ± 557.2 MPs/m3, 14.7 ± 3.7-69.3 ± 10.1 MPs/kg. Dry weight and 0.4-3.2 MPs/Fish, respectively. Surprisingly, MPs were found in every second fish sample, with a higher MP number in the gut than in the gills. Black and blue coloured filaments with <0.5 mm size were the dominant MPs with polypropylene and polyethylene polymers in abundance. The Polymer Hazard Index (PHI) and the Potential Ecological Risk Index (PERI) studies revealed that the majority of the sampling sites fell in Risk category V (dangerous category). An irregular trend in the MP concentration was observed downstream of the river, though relatively elevated MP concentrations in water and fish samples were observed downstream of the river. t-Distributed Stochastic Neighbour Embedding (t-SNE) unveiled distinct patterns in MP distribution with a higher similarity exhibited in the MPs found in fish gill and gut samples, unlike water and sediment, which shared certain characteristics. The findings in the current study contribute to filling the knowledge gap of MP assessment and accumulation in global freshwater systems and highlight the microplastic contamination and accumulation in fish with its potential implications on human health.

Microplastics increase cadmium absorption and impair nutrient uptake and growth in red amaranth (Amaranthus tricolor L.) in the presence of cadmium and biochar

Microplastic (MP) pollution in terrestrial ecosystems is gaining attention, but there is limited research on its effects on leafy vegetables when combined with heavy metals. This study examines the impact of three MP types-polyethylene (PE), polyethylene terephthalate (PET), and polystyrene (PS)-at concentrations of 0.02, 0.05, and 0.1% w/w, along with cadmium (Cd) and biochar (B), on germination, growth, nutrient absorption, and heavy metal uptake in red amaranth (Amaranthus tricolor L.). We found that different MP types and concentrations did not negatively affect germination parameters like germination rate, relative germination rate, germination vigor, relative germination vigor, and germination speed. However, they increased phytotoxicity and decreased stress tolerance compared to an untreated control (CK1). The presence of MPs, particularly the PS type, reduced phosphorus and potassium uptake while enhancing Cd uptake. For example, treatments PS0.02CdB, PS0.05CdB, and PS0.1CdB increased Cd content in A. tricolor seedlings by 158%, 126%, and 44%, respectively, compared to the treatment CdB (CK2). Additionally, MP contamination led to reduced plant height, leaf dry matter content, and fresh and dry weights, indicating adverse effects on plant growth. Moreover, the presence of MPs increased bioconcentration factors and translocation factors for Cd, suggesting that MPs might act as carriers for heavy metal absorption in plants. On the positive side, the addition of biochar improved several root parameters, including root length, volume, surface area, and the number of root tips in the presence of MPs, indicating potential benefits for plant growth. Our study shows that the combination of MPs and Cd reduces plant growth and increases the risk of heavy metal contamination in food crops. Further research is needed to understand how different MP types and concentrations affect various plant species, which will aid in developing targeted mitigation strategies and in exploring the mechanisms through which MPs impact plant growth and heavy metal uptake. Finally, investigating the potential of biochar application in conjunction with other amendments in mitigating these effects could be key to addressing MP and heavy metal contamination in agricultural systems.

Effective removal of microplastics by filamentous algae and its magnetic biochar: Performance and mechanism

In recent years, filamentous algae blooms and microplastics (MPs) pollution have become two major ecological and environmental problems in urban water systems. In order to solve these two problems at the same time, this study explored the loading capacity of MPs on fresh filamentous algae, and successfully synthesized magnetic filamentous algae biochar loading with Fe3O4 by hydrothermal method, with the purpose of removing MPs from water. The magnetic filamentous algal biochar was characterized by scanning electron microscopy (SEM), Fourier transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and so on. Experiments on adsorption kinetics, adsorption isotherms and optimum pH were carried out to explore the adsorption mechanism of MPs on magnetic filamentous algal biochar. The adsorption kinetics and adsorption isotherm models were evaluated, and the selection criterion for the appropriate model was determined by using the residual sum of squares (RSS) and Bayesian information criterion (BIC). Microscope images revealed that fresh filamentous algae could interact with MPs in the form of entanglement, adhesion and encapsulation. The average load of MPs in filamentous algae samples was 14.1 ± 5 items/g dry weight. The theoretical maximum adsorption capacities of polystyrene MPs (PS-MPs) by raw biochar (A500) and magnetic biochar with Fe3O4 (M2A500) were 176.99 mg/g and 215.58 mg/g, respectively. The adsorbent materials gave better reusability because they could be reused up to five times. Overall, these findings have provided new insights into the use of filamentous algae for in situ remediation of fluvial MPs pollution, as well as feasible strategies for the recycling of algal waste.

Eco-friendly hydrophobic ZIF-8/sodium alginate monolithic adsorbent: An efficient trap for microplastics in the aqueous environment

Microplastics (MPs), a newly emerging class of environmental contaminants, pose a severe threat to the entire ecosystem. The development of efficient and environmentally responsible adsorbents for removing the MPs is a particularly urgent research. Herein, a kind of monolithic ZIF-8 based adsorbents featuring stable hydrophobicity and micropore-mesopore-macropore hierarchical porous structure were fabricated by in situ growth of ZIF-8 nanoparticles on sodium alginate (SA) framework, and using polydimethylsiloxane (PDMS) as a hydrophobic agent. The monolithic nature of ZIF-8/SA allowed an easy solid-liquid separation process for adsorbents from water environment compared to powdered materials. The hierarchical porous structure ensures a remarkable MPs removal performance. The ZIF-8/SA showed high adsorption capacities of 594, 585, and 282 mg/g for polymethyl methacrylate (PMMA), poly (vinylidene difluoride) (PVDF), and polyvinyl chloride (PVC) respectively, and rapid adsorption kinetic progress within 120 min. The ZIF-8/SA adsorbents also exhibited excellent stability in the presence of interfering ions, acid/alkali, and humic acid, and displayed adsorption performance of > 70 % even in actual aquatic environment such as tap water, river water, and seawater. The results of characterizations showed that the synergistic effect of electrostatic interaction, hydrogen bonding, hydrophobic force, and van der Waals force was the main adsorption mechanism. The well-designed hydrophobic ZIF-8/SA monolithic materials would be promising to rapidly remove the MPs from the water environment.

Synthesis of recyclable and light-weight graphene oxide/chitosan/genipin sponges for the adsorption of diclofenac, triclosan, and microplastics

Emerging micropollutants, such as pharmaceuticals and microplastics (MPs), have become a pressing water environmental concern. The aim of this study is to synthesize chitosan sponges using graphene oxide (GO) and genipin (GP) for the removal of pharmaceuticals (diclofenac (DCF) and triclosan (TCS)) and MPs, verify their adsorption mechanisms, evaluate the effects of temperature, pH, and salinity on their adsorption capacities, and determine their reusability. The GO5/CS/GP sponge exhibited a macroporous nature (porosity = 95%, density = 32.6 mg/cm3). GO and cross-linker GP enhanced the adsorption of DCF, TCS, and polystyrene (PS) MPs onto the CS sponges. The adsorption of DCF, TCS, and PS MPs involved multiple steps: surface diffusion and pore diffusion of the sponge. The adsorption isotherms demonstrated that Langmuir model was the most fitted well model to explain adsorption of TCS (qm = 7.08 mg/g) and PS MPs (qm = 7.42 mg/g) on GO5/CS/GP sponge, while Freundlich model suited for DCF adsorption (qm = 48.58 mg/g). DCF adsorption was thermodynamically spontaneous and endothermic; however, the adsorption of TCS and PS MPs was exothermic (283-313 K). The optimal pH was 5.5-7 due to the surface charge of the GO5/CS/GP sponge (pHzpc = 5.76) and ionization of DCF, TCS, and PS MPs. As the salinity increased, DCF removal efficiency drastically decreased due to the weakening of electrostatic interactions; however, TCS removal efficiency remained stable because TCS adsorption was mainly caused by hydrophobic and π-π interactions rather than electrostatic interaction. The removal of PS MPs was enhanced by the electrostatic screening effects of high Na+ ions. PS nanoplastics (average size = 26 nm) were removed by the GO5/CS/GP sponge at a rate of 73.0%, which was better than that of PS MPs (41.5%). In addition, the GO5/CS/GP sponge could be recycled over five adsorption-desorption cycles.

Coagulative removal of polystyrene microplastics from aqueous matrices using FeCl3-chitosan system: Experimental and artificial neural network modeling

Effluent from sewage treatment plants (STPs) is a significant source of microplastics (MPs) re-entry into the environment. Coagulation-flocculation-sedimentation (CFS) process as an initial tertiary treatment step requires investigation for coagulative MPs removal from secondary-treated sewage effluents. In this study, experiments were conducted on synthetic water containing 25 mg/L polystyrene (PS) MPs using varying dosages of FeCl3 (1-10 mg/L) and chitosan (0.25-9 mg/L) to assess the effect of process parameters, such as pH (4-8), stirring speed (0-200 rpm), and settling time (10-40 min). Results revealed that ∼89.3% and 21.4% of PS removal were achieved by FeCl3 and chitosan, respectively. Further, their combination resulted in a maximum of 99.8% removal at favorable conditions: FeCl3: 2 mg/L, chitosan: 7 mg/L, pH: 6.3, stirring speed: 100 rpm, and settling time: 30 min, with a statistically significant (p < 0.05) effect. Artificial neural network (ANN) validated the experimental results with RMSE = 1.0643 and R2 = 0.9997. Charge neutralization, confirmed by zeta potential, and adsorption, ascertained by field-emission scanning electron microscope (FESEM) and Fourier-transform infrared spectroscopy (FTIR), were primary mechanisms for efficient PS removal. For practical considerations, the application of the FeCl3-chitosan system on the effluents from moving bed biofilm reactor (MBBR) and sequencing batch reactor (SBR)-based STPs, spiked with PS microbeads, showed > 98% removal at favorable conditions.

Lignin derived hydrophobic deep eutectic solvents for the extraction of nanoplastics from water

As a growing concern in aqueous systems, micro- and nano-plastics, especially nanoplastics (NPs), have been widely detected in the environment and organisms, posing a potential threat to ecosystems and human health. Hydrophobic deep eutectic solvents (HDESs) have emerged as environmentally friendly solvents that have shown promise for extracting pollutants from water, either for detection or removal purposes. Herein, we investigated the extraction of polystyrene (PS) and polyethylene terephthalate (PET) NPs from aqueous solution using lignin based HDESs as sustainable solvents. Rapid extraction of both PET and PS NPs was observed with the high extraction efficiency achieved (> 95%). The extraction capacities for PET and PS could reach up to 525.877 mg/mL and 183.520 mg/mL, respectively, by the Thymol-2,6-dimethoxyphenol 1:2 HDES. Moreover, the extraction mechanism was studied using various techniques including Fourier-transform infrared analysis, contact angle measurements, molecular dynamics simulation, kinetics, and isotherm studies. This work lays a foundational basis for the future development of innovative HDES-based technologies in the detection and remediation of NPs as part of the grand challenge of plastic pollution.

Conversion of locally available materials to biochar and activated carbon for drinking water treatment

For environmental sustainability and to achieve sustainable development goals (SDGs), drinking water treatment must be done at a reasonable cost with minimal environmental impact. Therefore, treating contaminated drinking water requires materials and approaches that are inexpensive, produced locally, and effortlessly. Hence, locally available materials and their derivatives, such as biochar (BC) and activated carbon (AC) were investigated thoroughly. Several researchers and their findings show that the application of locally accessible materials and their derivatives are capable of the adsorptive removal of organic and inorganic contaminants from drinking water. The application of locally available materials such as lignocellulosic materials/waste and its thermo-chemically derived products, including BC and AC were found effective in the treatment of contaminated drinking water. Thus, this review aims to thoroughly examine the latest developments in the use of locally accessible feedstocks for tailoring BC and AC, as well as their features and applications in the treatment of drinking water. We attempted to explain facts related to the potential mechanisms of BC and AC, such as complexation, co-precipitation, electrostatic interaction, and ion exchange to treat water, thereby achieving a risk-free remediation approach to polluted water. Additionally, this research offers guidance on creating efficient household treatment units based on the health risks associated with customized adsorbents and cost-benefit analyses. Lastly, this review work discusses the current obstacles for using locally accessible materials and their thermo-chemically produced by-products to purify drinking water, as well as the necessity for technological interventions.

Nanomaterials and biochar mediated remediation of emerging contaminants

The unrestricted release of various toxic substances into the environment is a critical global issue, gaining increased attention in modern society. Many of these substances are pristine to various environmental compartments known as contaminants/emerging contaminants (ECs). Nanoparticles and emerging sorbents enhanced remediation is a compelling methodology exhibiting great potential in addressing EC-related issues and facilitating their elimination from the environment, particularly those compounds that demonstrate eco-toxicity and pose considerable challenges in terms of removal. It provides a novel technique enabling the secure and sustainable removal of various ECs, including persistent organic compounds, microplastics, phthalate, etc. This extensive review presents a critical perspective on the current advancements and potential outcomes of nano-enhanced remediation techniques such as photocatalysis, nano-sensing, nano-enhanced sorbents, bio/phyto-remediation, which are applied to clean-up the natural environment. In addition, when dealing with residual contaminants, special attention is paid to both health and environmental implications; therefore, an evaluation of the long-term sustainability of nano-enhanced remediation methods has been considered. The integrated mechanical approaches were thoroughly discussed and presented in graphical forms. Thus, the critical evaluation of the integrated use of most emerging remediation technologies will open a new dimension in environmental safety and clean-up program.

Coagulation performance and mechanism of different hydrolyzed aluminum species for the removal of composite pollutants of polyethylene and humic acid

Microplastics (MPs) and natural organic matter (NOM) composite pollutants have become emerging contaminants with potential threats. Coagulation has been widely used to remove MPs and NOM, but the underlying mechanisms for the removal of MPs-NOM composite pollutants by hydrolyzed Al species remain unclear. Therefore, the coagulation performance and mechanism of AlCl3, polyaluminum chloride with basicity of 2.2 (PAC22), and PAC25 in treating polyethylene (PE), humic acid (HA), and PE-HA composite systems were systematically investigated. The results showed that in the single PE system, PAC25 with hexagonal clusters achieved the maximum removal (68.09 %) (pH: 5, dosage: 0.5 mM) since adsorption bridging and sweeping effect were the main mechanisms for PE removal. The adsorption of HA on the PE surface enhanced its hydrophilicity and electrostatic repulsion, resulting in decreased PE removal. In the AlCl3-PE-HA system, the oligomeric Al first interacted with the -COOH and C-OH of HA through complexation, followed by the meso- and polymers of Al interacted with PE by electrostatic adsorption. The pre-formed medium polymeric Al species (Alb) and colloidal or solid Al species (Alc) in PAC22 and PAC25 formed complexes with the -OH and -COOH groups of HA, respectively, and then removed PE by adsorption bridging and sweeping effect.

Microplastic pollutants in water: A comprehensive review on their remediation by adsorption using various adsorbents

Microplastics (MPs), as emerging pollutants, have attracted the attention of environmentalists, statespersons, and the scientific community over the last few decades. To address the spread of MPs in the environment, it is imperative to develop various removal techniques and materials that are effective, scalable, and ecologically benign. However, to the best of our knowledge, no review has systematically examined the removal of MPs using adsorption or provided an in-depth discussion on various adsorbents. Adsorption is an inexpensive and effective technology for wastewater treatment. Recently, many researchers have conducted studies on MP remediation using diverse adsorbent materials, such as biochar, activated carbon, sponges, carbon nanotubes, metal-layered oxides, metal-organic frameworks (MOFs), and zeolites. Each adsorbent has advantages and disadvantages. To overcome their disadvantages, researchers have been designing and developing hybrid adsorbents for MP remediation. This review provides insights into these individual adsorbents and also discusses hybrid adsorbents for MP removal. Finally, the review elaborates on future possibilities and ways to enable more efficient, scalable, and environmentally friendly MP cleanup. Overall, this review bridges the gap between contemporary MP remediation using adsorption techniques and adsorbent development.

Application of carbon-based adsorbents in the remediation of micro- and nanoplastics

Micro-nano plastics (MNPs) are emerging contaminants that can easily enter the food chain, posing risks to both the aquatic ecosystem and human health. Various physical, biological, and chemical methods have been explored to remove MNPs from water, and recently, adsorption technology has gained attention as an effective approach. Among the potential candidates, carbon-based adsorbent has emerged as a promising choice due to their low cost, eco-friendly nature, and sustainability. This paper summarizes recent advancements in MNP removal using carbon-based adsorbents, with a focus on the modification methods and adsorption mechanisms. Additionally, the factors influencing the adsorption performance and the methods for characterizing the adsorption mechanism are analyzed. Finally, the advantages and disadvantages of carbon-based adsorbents over other adsorbents are discussed, along with the current state of sustainable recycling and future research prospects.

Biochar-derived dissolved and particulate matter effects on the phytotoxicity of polyvinyl chloride nanoplastics

Nanoplastics in environments are potentially detrimental to plant growth. Appropriate doses of biochar can alleviate the phytotoxicity of nanoplastics under hydroponic conditions. However, the specific mechanisms remain unknown. In this study, the effects of biochar-derived dissolved matter (BCDM) and biochar-derived particulate matter (BCPM) on the phytotoxicity of polyvinyl chloride (PVC) nanoplastics were investigated and the underlying influencing mechanisms were elucidated. The results showed that PVC nanoplastics can be adsorbed and taken up by lettuce roots, inducing oxidative damage to lettuce shoots and roots and reducing their fresh weight. BCDM can promote the aggregation and sedimentation of PVC nanoplastics, and BCPM can adsorb PVC nanoplastics and cause barrier effect, which will reduce the exposure dose of PVC nanoplastics. Furthermore, nutrients in BCDM can promote lettuce growth. As a result, the presence of both BCDM and BCPM significantly mitigated the oxidative stress of lettuce shoots and roots as demonstrated by the decrease in hydrogen peroxide and malondialdehyde levels (p < 0.05). Meanwhile, lettuce biomass was significantly increased after addition of BCDM and BCPM compared to the single PVC treatment group (p < 0.05). This study provides a theoretical basis for finding solutions to alleviate the phytotoxicity of nanoplastics.

Effect of polyaniline dispersibility in chitin sponge matrix controlled by hydrophilicity on microplastics adsorption

Microplastics have become an emerging threat to global ecosystems, and their efficient removal faces with serious challenges. Herein, this study introduced different hydrophilic polyaniline (PANIs) into chitin matrix to fabricate Chitin-PANIs sponge (ChPANIs) and investigated the relationship between PANIs dispersibility in chitin sponge matrix controlled by its hydrophilicity and adsorption effects on MPs. With the increase of PANIs' hydrophilicity (WCA from 153.9° to 32.8°), the removal efficiency of sponges to MPs increased from 84.0 % to 91.7 %. More hydrophilic PANIs can provide more contact surfaces and adsorption sites, which enhanced the electrostatic interactions to MPs and obtained excellent adsorption properties. The adsorption of MPs on ChPANIs accorded with the pseudo-first-order adsorption, suggesting that physical adsorption plays a dominant role. The adsorption process also conformed to Freundlich model, which displayed the MPs adsorption on ChPANI-PA could be multi-layer. The adsorption strength of ChPANIs was 0.7552, suggesting that it was a strong adsorbent. The ChPANIs also exhibited good mechanical properties and reusability, which its MPs removal efficiency just decreased from 91.7 % to 86.9 % during the five cycles. These findings expand the understanding of the adsorption mechanism analysis of MPs on sponge materials, and exist guiding significance for the design of adsorbed materials.

Column-based removal of high concentration microplastics in synthetic wastewater using granular activated carbon

Microplastic (MP) is an emerging contaminant of concern due to its abundance in the environment. Wastewater treatment plant (WWTP) can be considered as one of the main sources of microplastics in freshwater due to its inefficiency in the complete removal of small MPs. In this study, a column-based MP removal which could serve as a tertiary treatment in WWTPs is evaluated using granular activated carbon (GAC) as adsorbent/filter media, eliminating clogging problems commonly caused by powder form activated carbon (PAC). The GAC is characterized via N2 adsorption-desorption isotherm, field emission scanning electron microscopy, and contact angle measurement to determine the influence of its properties on MP removal efficiency. MPs (40-48 μm) removal up to 95.5% was observed with 0.2 g/L MP, which is the lowest concentration tested in this work, but still higher than commonly used MP concentration in other studies. The performance is reduced with further increase in MP concentration (up to 1.0 g/L), but increasing the GAC bed length from 7.5 to 17.5 cm could lead to better removal efficiencies. MP particles are immobilized by the GAC predominantly by filtration process by being entangled with small GAC particles/chips or stuck between the GAC particles. MPs are insignificantly removed by adsorption process through entrapment in GAC porous structure or attachment onto the GAC surface.

Preparation of composite coagulant for the removal of microplastics in water

In this work, a composite flocculant (polyferric titanium sulfate-polydimethyldiallylammonium chloride [PFTS-PDMDAAC]) with a rich spatial network structure was prepared for the treatment of simulated wastewater containing polystyrene (PS) micro-nanoparticles. Characterization results showed that the surface of the PFTS-PDMDAAC was a three-dimensional network polymer of chain molecules that exhibited good thermal stability and formed an amorphous polymer containing multiply hydroxyl-bridged titanium and iron. When n(OH- ) : n(Fe) = 1:2, n(PO4 3- ) : n(Fe) = 0.35, n(Ti) : n(Fe) = 1:8, n(DMDAAC) : n(Fe) = 5:100, and the polymerization temperature is 60°C, the prepared composite flocculant has the best effect. The effects of dosage, pH, and agitation intensity on the flocculation properties of PFTS-PDMDAAC were also studied. The optimal removal rates of PS-μm and haze by PFTS-PDMDAAC were 85.60% and 90.10%, respectively, at a stirring intensity of 200 rpm, a pH of 9.0, and a PFTS-PDMDAAC dosage of 20 mg/L. The flocs produced by the PFTS-PDMDAAC flocculation were large and compact in structure, and the flocculation mechanism was mainly based on adsorption bridging. Kaolin played a promoting role in the process of PS-μm removal by PFTS-PDMDAAC floc and accelerated the formation of large and dense flocs. This study provided a reference for the coagulation method to remove micro-nanopollutants in the actual water treatment process. PRACTITIONER POINTS: A composite flocculant with rich spatial network structure (PFTS-PDMDAAC) was prepared. PFTS-PDMDAAC can effectively remove micro-nano polystyrene (PS) in wastewater. The floc produced by PFTS-PDMDAAC is large and compact in structure. The flocculation mechanism of PFTS-PDMDAAC is mainly adsorption bridging.

Microplastics removal technologies from aqueous environments: a systematic review

Purpose

Pollution of the environment with all kinds of plastics has become a growing problem. The problem of microplastics is mainly due to the absorption of stable organic pollutants and metals into them, and as a result, their environmental toxicity increases. The main purpose of this study is to investigate the appropriate and efficient methods of removing microplastics from aqueous environments through a systematic review.

Methods

Present study designed according to PRISMA guidelines. Two independent researchers followed all process from search to final analysis, for the relevant studies using international databases of PubMed, Scopus and ISI/WOS (Web of Science), without time limit. The search strategy developed based on the main axis of "microplastics", "aqueous environments" and "removal". This research was carried out from 2017 until the March of 2022. All relevant observational, analytical studies, review articles, and a meta-analysis were included.

Results

Through a comprehensive systematic search we found 2974 papers, after running the proses of refining, 80 eligible papers included to the study. According to the results of the review, the methods of removing microplastics from aquatic environments were divided to physical (12), chemical (18), physicochemical (27), biological (12) and integrated (11) methods. In different removal methods, the most dominant group of studied microplastics belonged to the four groups of polyethylene (PE), polystyrene (PS), polypropylene (PP) and polyethylene tetra phthalate (PET). Average removal efficiency of microplastics in different processes in each method was as: physical method (73.76%), chemical method (74.38%), physicochemical method (80.44%), biological method (75.23%) and integrated method (88.63%). The highest removal efficiency occurred in the processes based on the integrated method and the lowest efficiency occurred in the physical method. In total, 80% of the studies were conducted on a laboratory scale, 18.75% on a full scale and 1.25% on a pilot scale.

Conclusion

According to the findings; different processes based on physical, chemical, physicochemical, biological and integrated methods are able to remove microplastics with high efficiency from aqueous environments and in order to reduce their hazardous effects on health and environment, these processes can be easily used.

Control strategies for microplastic pollution in groundwater

Groundwater is the primary source of water that occurs below the earth's surface. However, the advancement in technology and the increasing population, which lead to the discharge of contaminants such as microplastics (MPs), have an adverse impact on the quality of groundwater. MPs are ubiquitous pollutants that are widely found throughout the world. The maximum abundance of MPs is 4 items/L and 15.2 items/L in groundwater at the specific location of China and USA. Various factors can affect the migration of MPs from soil to groundwater. The occurrence of MPs in water causes serious health issues. Therefore, taking appropriate strategies to control MP contamination in groundwater is urgent and important. This review summarizes the current literature on the migration process of MPs from soil to groundwater along with possible methods for the remediation of MP-polluted groundwater. The main objective of the review is to summarize the technical parameters, process, mechanism, and characteristics of various remediation methods and to analyze strategies for controlling MP pollution in groundwater, providing a reference for future research. Possible control strategies for MP pollution in groundwater include two aspects: i) prevention of MPs from entering groundwater; ii) remediation of polluted groundwater with MPs (ectopic remediation and in-situ remediation). Formulating legislative measures, strengthening public awareness and producing more environment-friendly alternatives can be helpful to reduce the production of MPs from the source. Manage plastic waste reasonably is also a good strategy and the most important part of the management is recycling. The shortcomings of the current study and the direction of future research are also highlighted in the review.

Scavenging microplastics and heavy metals from water using jujube waste-derived biochar in fixed-bed column trials

Extensive production and utilization of plastic products have resulted in the generation of microplastics (MPs), subsequently polluting the environment. The efficiency of biochars (BCs) derived from jujube (Ziziphus jujube L.) biomass (300 °C and 700 °C) for nylon (NYL) and polyethylene (PE) removal from contaminated water was explored in fixed-bed column trials. The optimum pH for the removal of both MPs was found 7. Both of the produced biochars demonstrated >99% removal of the MPs, while the sand filter exhibited a maximum of 78% removal of MPs. BC produced at 700 °C (BC700) showed 33-fold higher MPs retention, while BC produced at 300 °C (BC300) exhibited 20-fold higher retention, as compared to sand filters, indicating the higher efficiency of BC produced at higher pyrolysis temperature. Entrapment into the pores, entanglement with flaky structures of the BCs, and electrostatics interactions were the major mechanism for MPs retention in BCs. The efficiency of MPs-amended BCs was further explored for the removal of Pb(II) and Cd(II) in fixed-bed column trials. BC700 amended with PE and NYL exhibited the highest 50% breakthrough time (2114.23 and 2024.61 min, respectively, for Pb(II) removal and 2107.92 and 1965.19 min, respectively, for Cd(II) removal), as compared to sand filters (38.07 and 60.49 min for Pb(II) and Cd(II) removal, respectively). Thomas model predicted highest adsorption capacity was exhibited by BC700 amended with PE (584.34 and 552.80 mg g-1, for Pb(II) and Cd(II) removal, respectively), followed by BC700 amended with NYL (557.65 and 210.59 mg g-1 for Pb(II) and Cd(II) removal, respectively). Therefore, jujube waste-derived BCs could be used as efficient adsorbents to remove PE and NYL from contaminated water, while MPs-loaded BCs can further be utilized for higher adsorption of Pb(II) and Cd(II) from contaminated aqueous media. These findings suggest that BC could be used as an efficient adsorbent to remove the co-existing MPs-metals ions from the environment on a sustainable basis.

Clean water production from plastic and heavy metal contaminated waters using redox-sensitive iron nanoparticle-loaded biochar

The unceasing release of tiny plastics (microplastics and nanoplastics) and their additives, like metal ions, into the aquatic systems from industries and other sources is a globally escalating problem. Their combined toxic effects and human health hazard are already proven; hence, their remediation is requisite. This study utilised the nano-zerovalent iron-loaded sugarcane bagasse-derived biochar (nZVI-SBC) for simultaneous removal of Nanoplastics (NPs) of different functionality and size along with metal ions (Ni2+, Cd2+, AsO43-, and CrO42-). Batch and column experiments were conducted, and the results showed an efficient removal of contaminants with maximum sorption of carboxylate-modified NPs of size 500 nm (qmax = 90.3 mg/g) among all three NPs types. Significant removal was observed in Cd2+ in case of cations and CrO42- in case of anions with qmax = 44.0 and 87.8 mg/g, respectively. Kinetics and the isotherm modelling better fitted the pseudo-second-order kinetic model and Sips isotherm model, respectively for both NPs and metal ions. The designed material worked well in pH range of 4-8, ionic strength 1-20 mM and in complex aqueous matrices, with >90% removal. FTIR, zeta potential and the imaging analysis of the reaction precipitates confirmed the electrostatic attraction, pore retention and complexation as the potential mechanisms for removing NPs, whereas, XPS studies confirmed the reduction co-precipitation and surface complexation as the possible mechanism for removing metal ions. High values of attachment efficiency factor calculated from colloidal filtration theory (CFT) validated the experimental results and justified the high sorption of carboxylate modified 500 nm NPs particles. The synthesized material successfully removed both NPs of varying size and functionality and metal ions simultaneously with significant efficacy in complex environmental samples proving the broad applicability of material in realistic environmental conditions and different types of water treatment processes.

Microplastics removal from aqueous environment by metal organic frameworks

This paper provides an overview of recent research performed on the applications of metal-organic frameworks (MOFs) for microplastics (MPs) removal from aqueous environments. MPs pollution has become a major environmental concern due to its negative impacts on aquatic ecosystems and human health. Therefore, developing effective and sustainable methods for removing them from aqueous environments is crucial. In recent years, MOFs have emerged as a promising solution for this purpose due to their unique properties such as high surface area, renewability, chemical stability, and versatility. Moreover, their specific properties such as their pore size and chemical composition can be tailored to enhance their efficiency in removing MPs. It has been shown that MOFs can effectively adsorb MPs from aqueous media in the range of 70-99.9%. Besides some high price concerns, the main drawback of using MOFs is their powder form which can pose challenges due to their instability. This can be addressed by supporting MOFs on other substrates such as aerogels or foams. Meanwhile, there is a need for more research to investigate the long-term stability of MOFs in aqueous environments and developing efficient regeneration methods for their repeated use.

Reviewing the role of biochar in paddy soils: An agricultural and environmental perspective

The main challenge of the twenty-first century is to find a balance between environmental sustainability and crop productivity in a world with a rapidly growing population. Soil health is the backbone of a resilient environment and stable food production systems. In recent years, the use of biochar to bind nutrients, sorption of pollutants, and increase crop productivity has gained popularity. This article reviews key recent studies on the environmental impacts of biochar and the benefits of its unique physicochemical features in paddy soils. This review provides critical information on the role of biochar properties on environmental pollutants, carbon and nitrogen cycling, plant growth regulation, and microbial activities. Biochar improves the soil properties of paddy soils through increasing microbial activities and nutrient availability, accelerating carbon and nitrogen cycle, and reducing the availability of heavy metals and micropollutants. For example, a study showed that the application of a maximum of 40 t ha-1 of biochar from rice husks prior to cultivation (at high temperature and slow pyrolysis) increases nutrient utilization and rice grain yield by 40%. Biochar can be used to minimize the use of chemical fertilizers to ensure sustainable food production.

Adsorptive removal of dimethyl phthalate using peanut shell-derived biochar from aqueous solutions: equilibrium, kinetics, and mechanistic studies

Rise in polymer industry and extensive use of their products leads to leaching of phthalate esters and distributed into the different matrices of the environment. This chemical group has the potential to hamper the life of living organisms and ecosystem. Thus, it is essential to develop cost-effective adsorbents capable of removing these harmful compounds from the environment. In this work, peanut hull-derived biochar was taken as the adsorbent, and DMP was selected as the model pollutant or adsorbates. The biochars of different properties were produced at three pyrolysis temperatures (i.e., 450, 550, and 650 °C) to check how temperature affected the adsorbent properties and adsorption performance. Consequently, the performance of biochars for DMP adsorption was thoroughly studied by the combination of experiments and compared with commercial activated carbon (CAC). All the adsorbents are meticulously characterized using various analytical techniques and used for adsorption DMP from aqueous solutions. The results suggested that adsorption was favoring chemisorption with multi-layered adsorption as adsorption kinetics and isotherm are in good alignment with pseudo-second-order kinetics and Freundlich isotherm, respectively. Further, thermodynamic study revealed DMP adsorption on adsorbent is physically spontaneous and endothermic. The removal efficiency order of four adsorbent was as follows: BC650 > CAC > BC550 > BC450 with maximum efficiency of 98.8% for BC650 followed by 98.6% for CAC at optimum conditions. And as it is a short carbon chain PAE, dominant mechanisms of adsorption for DMP onto porous biochar were H-bonding, π-π EDA interactions, and diffusion within the pore spaces. Therefore, this study can provide strategies for the synthesis of biochar for effectively removing DMP from aqueous solution.

A sustainable layered nanofiber/sheet aerogels enabling repeated life cycles for effective oil/water separation

Discarded oil-containing absorbents, which has been used in handling oil spills, are tricky to deal with and have rose global environmental concerns regarding release of microplastics. Herein, we developed a facile strategy to fabricate sustainable absorbents by a gas-inflating method, through which 2D electrospinning polycaprolactone nanofiber membranes were directly inflated into highly porous 3D nanofiber/sheet aerogels with layered long fiber structure. The membranes were inflated rapidly from a baseline porosity of 81.98% into 97.36-99.42% in 10-60 min. The obtained aerogels were further wrapped with -CH₃ ended siloxane structures using CH₃SiCl₃. This hydrophobic absorbent (CA ≈ 145°) could rapidly trap oils from water with sorption range of 25.60-42.13 g/g and be recycled by simple squeeze due to its mechanical robustness. As-prepared aerogels also showed high separation efficiency to separate oils from both oil/water mixtures and oil-in-water emulsions (>96.4%). Interestingly, the oil-loaded absorbent after cleaning with absolute ethanol could be re-dissolved in selected solvents and promptly reconstituted by re-electrospinning and gas-inflation. The reconstituted aerogels were used as fire-new oil absorbents for repeated life cycles. The novel design, low cost and sustainability of the absorbent provides an efficient and environmentally-friendly solution for handling oil spills.

Mechanisms of polystyrene nanoplastics adsorption onto activated carbon modified by ZnCl2

In this study, the adsorption capacity of activated carbon was enhanced after zinc chloride activation. The effects of pore filling, n-π and π-π interaction and electrostatic interaction on the adsorption of polystyrene nanoplastics (PSNPs) by activated carbon were determined by SEM, BET, Raman spectrum, FTIR and surface Zeta potential. Pore filling, electrostatic interaction and n-π interaction and π-π interaction all played a role in the adsorption process, but n-π interaction and π-π interaction was not the decisive role. The adsorption of PSNPs on activated carbon conformed to the pseudo-second-order kinetics and Langmuir isotherm, and there was spontaneous physical adsorption process driven by entropy in the adsorption process. Further, the effects of common anions SO₄^2-, HCO₃^-, and Cl^- in water on the adsorption of PSNPs by activated carbon were investigated, and the results showed that the presence of these ions could increase the adsorption capacity to some extent. ZCAC has a stable adsorption capacity under tap water, but its adsorption capacity is affected under lake water. In addition, the reuse of activated carbon was investugated, and the adsorption capacity of activated carbon was fully recovered after high temperature calcination. This study provided a direction for materials modification of adsorbed nanoplastics and a feasible method for removal of nanoplastics in drinking water treatment plants.

Removal of pristine and aged microplastics from water by magnetic biochar: Adsorption and magnetization

Adsorption is an efficient and eco-friendly removal technique for small pristine microplastics in water. However, small pristine microplastics are not representative of those large microplastics in natural water with different aging levels. Whether the adsorption technique is effective in removing large aged microplastics from water remained unknown. To this end, the removal efficiency of large polyamide (PA) microplastics with different aging time by magnetic corncob biochar (MCCBC) was evaluated under different experimental conditions. After treated by heated-activated potassium persulfate, the physicochemical properties of PA have changed dramatically, as evidenced by rough surface, decreased particle size and crystallinity, and increased oxygen-containing functional groups, which enhanced with aging time. These changes promoted the combination of aged PA and MCCBC, thereby resulting in a higher removal efficiency of aged PA (~97 %) than that of pristine ones (~25 %). It is supposed that the adsorption process was a result of complexation, hydrophobic interaction, and electrostatic interaction. Increased ionic strength inhibited the removal of both pristine and aged PA, and neutral pH conditions favored PA removal. Furthermore, particle size played a great role in the removal of aged PA microplastics. When the particle size of aged PA was smaller than 75 μm, their removal efficiency was significantly increased (p < 0.01). The small PA microplastics were removed by adsorption, whereas the large ones were removed by magnetization. These research findings highlight magnetic biochar as promising technique for removing environmental microplastics.

Trash to treasure: electrocatalytic upcycling of polyethylene terephthalate (PET) microplastic to value-added products by Mn0.1Ni0.9Co2O4-δ RSFs spinel

Microplastic pollution has emerged as a pressing environmental issue of global concern due to its detrimental effects on the environment and ecology. Restricted to their characters of complex composition, it is a great challenge to propose a more cost-effective approach to achieve highly selective conversion of microplastic into add-value products. Here we demonstrate an upcycling strategy for converting PET microplastics into added-value chemicals (formate, terephthalic acid and K₂SO₄). PET is initially hydrolyzed in KOH solution to produce terephthalic acid and ethylene glycol, which is subsequently used as an electrolyte to produce formate at the anode. Meanwhile, the cathode undergoes hydrogen evolution reaction to produce H₂. Preliminary techno-economic analysis suggests that this strategy has certain economic feasibility and a novel Mn_0.1Ni_0.9Co₂O_4-δ rod-shaped fiber (RSFs) catalyst we synthesized can achieve high Faradaic efficiency (> 95%) at 1.42 V vs. RHE with optimistic formate productivity. The high catalytic performance can be attributed to the doping of Mn changing the electronic structure and reducing the metal-oxygen covalency of NiCo₂O₄, reducing the lattice oxygen oxidation in spinel oxide OER electrocatalysts. This work not only put forward an electrocatalytic strategy for PET microplastic upcycling but also guides the design of electrocatalysts with excellent performance.

The potential risks posed by micro-nanoplastics to the safety of disinfected drinking water

Micro-nanoplastics (M-NPs) have become an emerging critical issue in the environment because they migrate easily, can bioaccumulate with toxic effects, and are difficult to degrade. Unfortunately, the current technologies for removing or degrading M-NPs in drinking water are insufficient to eliminate them completely, and residual M-NPs in drinking water may pose a threat to human health by impairing human immunity and metabolism. In addition to their intrinsic toxic effects, M-NPs may be even more harmful after drinking water disinfection than before disinfection. Herein, this paper comprehensively summarizes the negative impacts of several commonly used disinfection processes (ozone, chlorine, and UV) on M-NPs. Moreover, the potential leaching of dissolved organics from M-NPs and the production of disinfection byproducts during the disinfection process are discussed in detail. Moreover, due to the diversity and complexity of M-NPs, their adverse effects may exceed those of conventional organics (e.g., antibiotics, pharmaceuticals, and algae) after the disinfection process. Finally, we propose enhanced conventional drinking water treatment processes (e.g., enhanced coagulation, air flotation, advanced adsorbents, and membrane technologies), detection of residual M-NPs, and biotoxicological assessment as promising and ecofriendly candidates to efficiently remove M-NPs and avoid the release of secondary hazards.

Microplastics in facial cleanser: extraction, identification, potential toxicity, and continuous-flow removal using agricultural waste-based biochar

Microplastic (MP) is an emerging contaminant of concern due to its ubiquitous quantity in the environment, small size, and potential toxicity due to strong affinity towards other contaminants. In this work, MP particles (5-300 μm) were extracted from a commercial facial cleanser and determined to be irregular polyethylene (PE) microbeads based on characterization with field emission scanning electron microscopy (FESEM) and Raman spectroscopy. The potential of extracted MP acting as toxic pollutants' vector was analyzed via adsorption of methylene blue and methyl orange dye where significant dye uptake was observed. Synthetic wastewater containing the extracted MP was subjected to a continuous-flow column study using palm kernel shell and coconut shell biochar as the filter/adsorbent media. The prepared biochar was characterized via proximate and ultimate analysis, FESEM, contact angle measurement, atomic force microscopy (AFM), and Fourier transform infrared (FTIR) spectroscopy to investigate the role of the biochar properties in MP removal. MP removal performance was determined by measuring the turbidity and weighing the dry mass of particles remaining in the effluent following treatment. Promising results were obtained from the study with highest removal of MP (96.65%) attained through palm kernel shell biochar with particle size of 0.6-1.18 mm and continuous-flow column size of 20 mm.

Biomass Chitosan-Based Tubular/Sheet Superhydrophobic Aerogels Enable Efficient Oil/Water Separation

Water pollution, which is caused by leakage of oily substances, has been recognized as one of the most serious global environmental pollutions endangering the ecosystem. High-quality porous materials with superwettability, which are typically constructed in the form of aerogels, hold huge potential in the field of adsorption and removal of oily substances form water. Herein, we developed a facile strategy to fabricate a novel biomass absorbent with a layered tubular/sheet structure for efficient oil/water separation. The aerogels were fabricated by assembling hollow poplar catkin fiber into chitosan sheets using a directional freeze-drying method. The obtained aerogels were further wrapped with -CH₃-ended siloxane structures using CH₃SiCl₃. This superhydrophobic aerogel (CA ≈ 154 ± 0.4°) could rapidly trap and remove oils from water with a large sorption range of 33.06-73.22 g/g. The aerogel facilitated stable oil recovery (90.07-92.34%) by squeezing after 10 sorption-desorption cycles because of its mechanical robustness (91.76% strain remaining after 50 compress-release cycles). The novel design, low cost, and sustainability of the aerogel provide an efficient and environmentally friendly solution for handling oil spills.

Biochar as a Green Sorbent for Remediation of Polluted Soils and Associated Toxicity Risks: A Critical Review

Soil contamination with organic contaminants and various heavy metals has become a global environmental concern. Biochar application for the remediation of polluted soils may render a novel solution to soil contamination issues. However, the complexity of the decontaminating mechanisms and the real environment significantly influences the preparation and large-scale application of biochar for soil ramification. This review paper highlights the utilization of biochar in immobilizing and eliminating the heavy metals and organic pollutants from contaminated soils and factors affecting the remediation efficacy of biochar. Furthermore, the risks related to biochar application in unpolluted agricultural soils are also debated. Biochar production conditions (pyrolysis temperature, feedstock type, and residence time) and the application rate greatly influence the biochar performance in remediating the contaminated soils. Biochars prepared at high temperatures (800 °C) contained more porosity and specific surface area, thus offering more adsorption potential. The redox and electrostatic adsorption contributed more to the adsorption of oxyanions, whereas ion exchange, complexation, and precipitation were mainly involved in the adsorption of cations. Volatile organic compounds (VOCs), dioxins, and polycyclic aromatic hydrocarbons (PAHs) produced during biochar pyrolysis induce negative impacts on soil alga, microbes, and plants. A careful selection of unpolluted feedstock and its compatibility with carbonization technology having suitable operating conditions is essential to avoid these impurities. It would help to prepare a specific biochar with desired features to target a particular pollutant at a specific site. This review provided explicit knowledge for developing a cost-effective, environment-friendly specific biochar, which could be used to decontaminate targeted polluted soils at a large scale. Furthermore, future study directions are also described to ensure a sustainable and safe application of biochar as a soil improver for the reclamation of polluted soils.

Innovations in the Development of Promising Adsorbents for the Remediation of Microplastics and Nanoplastics - A Critical Review

Microplastics and nanoplastics are being assumed as emerging toxic pollutants owing to their unique persistent physicochemical attributes, chemical stability, and nonbiodegradable nature. Owing to their possible toxicological impacts (not only on aquatic biota but also on humans), scientific communities are developing innovative technologies to remove microplastics and nanoplastics from polluted waters. Various technologies, including adsorption, coagulation, photocatalysis, bioremediation, and filtration, have been developed and employed to eliminate microplastics and nanoplastics. Recently, adsorption technology has been getting great interest in capturing microplastics and nanoplastics and achieving excellent removal performance. Therefore, this review is designed to discuss recent innovations in developing promising adsorbents for the remediation of microplastics and nanoplastics from wastewater and natural water. The developed adsorbents have been classified into four main classes: sponge/aerogel-based, metal-based, biochar-based, and other developed adsorbents, and their performance efficiencies have been critically examined. Further, the influence of various pertinent factors, including adsorbents' characteristics, microplastics/nanoplastics' characteristics, solution pH, reaction temperature, natural organic matter, and co-existing/interfering ions on the removal performance of advanced adsorbents, have been critically assessed. Importantly, the particle application of the developed adsorbents in removing microplastics and nanoplastics from natural water has been elucidated. In addition, barriers to market penetration of the developed adsorbents are briefly discussed to help experts transfer adsorption-based technology from laboratory-scale to commercial applications. Finally, the current knowledge gaps and future recommendations are highlighted to assist scientific communal for improving adsorption-based technologies to battle against microplastics and nanoplastics pollution.

Removal of nanoplastics from aqueous solution by aggregation using reusable magnetic biochar modified with cetyltrimethylammonium bromide

Nanoplastics (NPs) pollution has become an emerging threat to the aquatic environment and its organisms. The removal of NPs from contaminated water is a global challenge. In this study, an efficient and reusable composite was prepared from cetyltrimethylammonium bromide (CTAB) modified magnetic biochar. The performances of CTAB modified magnetic biochar (CMB) to remove polystyrene (PS) and carboxylate-modified polystyrene (CPS) nanoparticles from water were systematically evaluated. The results showed that the PS and CPS removal performance of magnetic biochar was improved by CTAB modification. These increases were assigned to the increase in the surface hydrophobicity of CMB. Due to the strong electrostatic repulsion between the nanoparticles, PS and CPS maintained high stability in alkaline conditions, resulting in a significant decrease in removal efficiency. The removal efficiency was decreased to 67.4% for PS and to 40.7% for CPS at pH 11. The inhibition effects of NaCl on the PS and CPS removal efficiencies were decreased gradually with the increase of NaCl concentration. Among the anions studied, H₂PO₄^- had the biggest impact on the removal performance of CMB. Besides, CMB could be used to remove PS and CPS in real surface water, and the removal efficiencies of PS and CPS were 95.3% and 97.8%, respectively. Particularly, the removal efficiencies of PS and CPS were 90.2% for PS and 94.8% for CPS when CMB was recycled five times. According to the characterization results of XRD, TGA, SEM, FTIR and XPS, PS and CPS nanoparticles were removed by CMB from water mainly through aggregation instead of adsorption. The efficient removal of PS and CPS by CMB via aggregation process offers new insight into the removal of NPs from aquatic environment.

Biochar for the Removal of Emerging Pollutants from Aquatic Systems: A Review

Water contaminated with emerging pollutants has become a serious environmental issue globally. Biochar is a porous and carbon-rich material produced from biomass pyrolysis and has the potential to be used as an integrated adsorptive material. Many studies have shown that biochar is capable to adsorb emerging pollutants from aquatic systems and could be used to solve the water pollution problem. Here, we provided a dual perspective on removing emerging pollutants from aquatic systems using biochar and analyzed the emerging pollutant removal efficiency from the aspects of biochar types, pollutant types and coexistence with heavy metals, as well as the associated mechanisms. The potential risks and future research directions of biochar utilization are also presented. This review aims to assist researchers interested in using biochar for emerging pollutants remediation in aquatic systems and facilitate research on emerging pollutants removal, thereby reducing their environmental risk.

Current status of microplastics and nanoplastics removal methods: Summary, comparison and prospect

In modern society, plastics also play an indispensable role in people's lives due to their various excellent properties. However, when these plastic products are discarded after being used, after being subjected to external influences, they will continue to be worn, damaged and degraded into micro- and nano-scale plastics, which are microplastics and nanoplastics (M/NPs). Although people's attention has been paid to M/NPs at present, the focus is still mainly on the detection and hazard of M/NPs, and how to remove M/NPs is relatively less popular. This review was written in order to draw the attention of more researchers to remove M/NPs. This review first briefly introduces the research background of M/NPs, and also shows the main analytical methods currently used for qualitative and quantitative M/NPs. Then, most of the current literature on the removal of M/NPs was collected, and they were classified, summarized, and introduced according to the classification of physical, physicochemical, and biological methods. The advantages and disadvantages of various methods are summarized, and they are also compared, which can help more researchers choose the appropriate method for research. In addition, the application scenarios of these methods are briefly introduced. Finally, some future research directions are proposed for the current research status of M/NPs removal. It is hoped that this will further promote the development on the method of removing M/NPs.

Global distribution of microplastic contaminants in aquatic environments and their remediation strategies

This review describes the occurrence and distribution of microplastics in freshwater and marine environments in recent years (2017-2022). Use of microplastics often results in contamination of aquatic environments, threatens biodiversity, and creates the need for environmental remediation. Such remediation strategies can involve primary, secondary, and tertiary treatments. Tertiary treatment is a frequent research subject due to its high efficiency and the possibility for advancements and enhancements. This study discusses tertiary treatments with remediation efficiencies of 95% and greater and their advantages, disadvantages, and future perspectives. Biochar-mediated remediation of microplastics is an effective method that may be able to achieve efficiencies approaching 100%. The study concludes by exploring methods of removing microplastics, including constructed wetlands and biochar, which offer high efficiency. PRACTITIONER POINTS: Tertiary treatments are an effective microplastic remediation strategy applicable succeeding secondary or primary treatments or as an individual remediation strategy. Biochar is a highly efficient adsorbent for microplastic remediation from aquatic environment with eco-friendly aspect and reusability. Modifications in tertiary treatments and enhancement in remediation efficiency are still a subject of research for future studies.

Removal of nanoplastics in water treatment processes: A review

Nanoplastics are drawing a significant attention as a result of their propensity to spread across the environment and pose a threat to all organisms. The presence of nanoplastics in water is given attention nowadays as the transit of nanoplastics occurs through the aquatic ecosphere besides terrestrial mobility. The principal removal procedures for macro-and micro-plastic particles are effective, but nanoparticles escape from the treatment, increasing in the water and significantly influencing the society. This critical review is aimed to bestow the removal technologies of nanoplastics from aquatic ecosystems, with a focus on the treatment of freshwater, drinking water, and wastewater, as well as the importance of transit and its impact on health concerns. Still, there exists a gap in providing a collective knowledge on the methods available for nanoplastics removal. Hence, this review offered various nanoplastic removal technologies (microorganism-based degradation, membrane separation with a reactor, and photocatalysis) that could be the practical/effective measures along with the traditional procedures (filtration, coagulation, centrifugation, flocculation, and gravity settling). From the analyses of different treatment systems, the effectiveness of nanoplastics removal depends on various factors, source, size, and type of nanoplastics apart from the treatment method adopted. Combined removal methods, filtration with coagulation offer great scope for the removal of nanoplastics from drinking water with >99 % efficiency. The collected data could serve as base-line information for future research and development in water nanoplastics cleanup.

Biochar derived carbonaceous material for various environmental applications: Systematic review

Biochar is the solid material produced from the carbonization of organic feedstock biomass. This material has several unique characteristics such as greater carbon content, good electrical conductivity, high stability and large surface area, which can be applied in several research areas such as generation of power and wastewater treatment. In connection with this, recently, the investigations on biochar significantly focus on the removal of toxic heavy metals since the biochar material is easily available and environmentally friendly. According to an environmental analytical device, biochar-derived carbonaceous material has been additionally applied to the synthesis of an effective, sensitive, and low-cost electrochemical sensor. Biochar with an assessment of electrochemical properties has engaged with different redox reactions in water. In this survey, electrochemical ways of behaving of biochar in light of the electrochemical structures were analytically compiled as well as the impact from biomass sources and manufacturing process including carbonization strategies, pre-treatment/changed techniques. This review emphasizes the various synthesis methods of biochar form organic feedstock, properties and different modulations of biochar for the bioremediation of heavy metals. This review study emphasizes the utilization of biochar as sensing platform and supercapacitor for electrode fabrication in electrochemical biosensor to enhance the remediation of toxic contaminants from water streams and by switching the less ecological traditional materials. Brief information on the techniques employed for packaging biochar as carbon electrode is summarized. Scope in the aspect of environmental concern of biochar, future challenges and prospects are proposed in detail.

Addition of biochar as thin preamble layer into sand filtration columns could improve the microplastics removal from water

The release of microplastics (MPs) especially those with sizes less than 10 μm from effluent of wastewater treatment plants (WWTPs) is one of the major sources of plastics into aquatic environment. To reduce the discharge of MPs into environment, it is essential to further enhance their removal efficiencies in WWTPs. In present study, to boost the removal performance of MPs in sand filtration systems (units that commonly employed in WWTPs to remove colloidal pollutants), six types of biochar fabricated from three raw biomass materials (i.e. lignin, cellulose, and woodchips) at two pyrolysis temperatures (400 °C and 700 °C) was respectively amended into sand columns as thin permeable layer. We found that adding all six types of biochar into sand columns as thin permeable layer could greatly improve the retention of MPs with the diameter of 1 μm under either slow (4 m/d) or fast flow rates (160 m/d) due to the high adsorption capability of biochar. Woodchip-derived biochar exhibited the highest MPs retention performance, which was followed by cellulose-derived biochar and then lignin-derived biochar. Moreover, for biochar derived from three raw biomasses, increasing pyrolysis temperature could improve MPs retention performance. The direct observation of real-time plastics retention processes on different types of biochar via a visible flow chamber showed that woodchip-derived biochar especially that fabricated at 700 °C exhibited more MPs trapping processes relative to lignin and cellulose-derived biochar due to their more complex surface morphology. Thus, the highest MPs retention performance was achieved in sand columns with amendment by 1 wt% woodchip-derived biochar fabricated at 700 °C. More importantly, we found that for these modified sand filtration column systems, complete MPs removal could be achieved in real river water and actual sewage water, in multiple filtration cycles, longtime filtration process (100 pore volumes injection) as well as with interval flow conditions. Moreover, biochar could be regenerated and reused as thin permeable layer to effectively remove MPs. The results of this study clearly showed that biochar especially woodchip-derived biochar fabricated at 700 °C had the potential to immobilize MPs especially those with small sizes in WWTPs.

Emerging electrochemical techniques for identifying and removing micro/nanoplastics in urban waters

The ubiquitous micro/nanoplastics (MPs/NPs) in urban waters are priority pollutants due to their toxic effects on living organisms. Currently, great efforts have been made to realize a plastic-free urban water system, and the identification and removal of MPs/NPs are two primary issues. Among diverse methods, emerging electrochemical techniques have gained growing interests owing to their facile implementation, high efficiency, eco-compatibility, onsite operation, etc. Herein, recent progress in the electrochemical identification and removal of MPs/NPs in urban waters are comprehensively reviewed. The electrochemical sensing of MPs/NPs and their released pollutants (e.g., bisphenol A (BPA)) has been analyzed, and the sensing principles and the featured electrochemical devices/electrodes are examined. Afterwards, recent applications of electrochemical methods (i.e., electrocoagulation, electroadsorption, electrokinetic separation and electrochemical degradation) in MPs/NPs removal are discussed in detail. The influences of critical parameters (e.g., plastics' property, current density and electrolyte) in the electrochemical identification and removal of MPs/NPs are also analyzed. Finally, the current challenges and prospects in electrochemical sensing and removal of MPs/NPs in urban waters are elaborated. This review would advance efficient electrochemical technologies for future MPs/NPs pollutions management in urban waters.

Removal of microplastics and nanoplastics from urban waters: Separation and degradation

The omnipresent micro/nanoplastics (MPs/NPs) in urban waters arouse great public concern. To build a MP/NP-free urban water system, enormous efforts have been made to meet this goal via separating and degrading MPs/NPs in urban waters. Herein, we comprehensively review the recent developments in the separation and degradation of MPs/NPs in urban waters. Efficient MP/NP separation techniques, such as adsorption, coagulation/flocculation, flotation, filtration, and magnetic separation are first summarized. The influence of functional materials/reagents, properties of MPs/NPs, and aquatic chemistry on the separation efficiency is analyzed. Then, MP/NP degradation methods, including electrochemical degradation, advanced oxidation processes (AOPs), photodegradation, photocatalytic degradation, and biological degradation are detailed. Also, the effects of critical functional materials/organisms and operational parameters on degradation performance are discussed. At last, the current challenges and prospects in the separation, degradation, and further upcycling of MPs/NPs in urban waters are outlined. This review will potentially guide the development of next-generation technologies for MP/NP pollution control in urban waters.

Biochar in environmental friendly fertilizers - Prospects of development products and technologies

According to the circular economy concept, the production of fertilizers should be closed in a loop, which prevents excessive emissions and harmful effects to the environment. Biological wastes are problematic to collect and transport. They undergo a biological transformation that causes greenhouse gases emission and sanitary hazards. Biomass sources used for organic or organo-mineral fertilizers must be free of pathogens and rich in macro and microelements. Solid residues can be processed thermally. Biochar is a carbon produced by biomass pyrolysis without oxygen presence and has been used for many years to improve soil quality and enhance the efficiency of fertilization. There are many research works on the use of biochar in fertilization. This study is also extended by the latest developments and technologies from the patent database (recent year) and biochar-based fertilizers market. To the best of our knowledge, there is no such review currently available in scientific databases. Based on the collected data, the best method of biochar management was proposed - soil application. Biochar applied to soil has several advantages: it improves soil structure and its sorption capacity, enhances soil-nutrient retention and water-holding capacity, immobilizes contaminants from soil (sorption), reduces greenhouse gas emissions and soil nutrient leaching losses while stimulating the growth of a plant.

Microplastics and nanoplastics: Recent literature studies and patents on their removal from aqueous environment

The presence of microplastics (MP) and nanoplastics (NP) in the environment poses significant hazards towards microorganisms, humans, animals and plants. This paper is focused on recent literature studies and patents discussing the removal process of these plastic pollutants. Microplastics and nanoplastics can be quantified by counting, weighing, absorbance and turbidity and can be further analyzed using scanning electron microscopy (SEM), dynamic light scattering (DLS), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, surface-enhanced Raman spectroscopy and Raman tweezers. Mitigation methods reported are categorized depending on the removal characteristics: (i) Filtration and separation method: Filtration and separation, electrospun nanofiber membrane, constructed wetlands; (ii) Capture and surface attachment method: coagulation, flocculation and sedimentation (CFS), electrocoagulation, adsorption, magnetization, micromachines, superhydrophobic materials and microorganism aggregation; and (iii) Degradation method: photocatalytic degradation, microorganism degradation and thermal degradation; where removal efficiency between 58 and 100% were reported. As these methods are significantly distinctive, the parameters which affect the MP/NP removal performance e.g., pH, type of plastics, presence of interfering chemicals or ions, surface charges etc. are also discussed. 42 granted international patents related to microplastics and nanoplastics removal are also reviewed where the majority of these patents are focused on separation or filtration devices. These devices are efficient for microplastics up to 20 μm but may be ineffective for nanoplastics or fibrous plastics. Several patents were found to focus on methods similar to literature studies e.g., magnetization, CFS, biofilm and microorganism aggregation; with the addition of another method: thermal degradation.