Activation of peroxymonosulfate by base: Implications for the degradation of organic pollutants

Facilely tuning the coating layers of Fe nanoparticles from iron carbide to iron nitride for different performance in Fenton-like reactions

In this study, a series of Fe-based materials are facilely synthesized using MIL-88A and melamine as precursors. Changing the mass ratio of melamine and MIL-88A could tune the coating layers of generated zero-valent iron (Fe0) particles from Fe3C to Fe3N facilely. Compared to Fe/Fe3N@NC sample, Fe/Fe3C@NC exhibits better catalytic activity and stability to degrade carbamazepine (CBZ) with peroxymonosulfate (PMS) as oxidant. Free radical quenching tests, open-circuit potential (OCP) test and electron paramagnetic resonance spectra (EPR) prove that hydroxyl radicals (OH) and superoxide radical (O2-) are dominant reactive oxygen species (ROSs) with Fe/Fe3C@NC sample. For Fe/Fe3N@NC sample, the main ROSs are changed into sulfate radicals (SO4-) and high valent iron-oxo (Fe (IV)=O) species. In addition, the better conductivity of Fe3C is beneficial for the electron transfer from Fe0 to the Fe3C, thus could keep the activity of the surface sites and obtain better stability. DFT calculation reveals the better adsorption and activation ability of Fe3C than Fe3N. Moreover, PMS can also be adsorbed on the Fe sites of Fe3N with shorter FeO bonds and longer SO bonds than on Fe3C, the Fe (IV)=O is thus present in the Fe/Fe3N@NC/PMS system. This study provides a novel strategy for the development of highly active Fe-based materials for Fenton-like reactions and thus could promote their real application.

Autocatalytic degradation of Cu-EDTA in the Calcite/PMS system: Singlet oxygen and Cu(III)

The simultaneous removal of heavy metal complexes (HMCs) and heavy metal ions presents a significant challenge in treating wastewater. To address this, we propose a Calcite/Peroxymonosulfate (Calcite/PMS) system aimed at simultaneously decomplexing Cu-EDTA and removing Cu ions. Calcite/PMS system could achieve 99.5 % Cu-EDTA decomplexation and 61.9 % Cu ions removal within 60 min under initial conditions of Cu-EDTA (10 mg/L), Calcite (3 g/L), and PMS (2 mM). Singlet oxygen (1O2) emerged as the predominant reactive species responsible for Cu-EDTA decomplexation, which selectively targeted the N-C bonds in the Cu-EDTA structure to produce intermediates with lower biotoxicity than EDTA. Interestingly, solid phase Cu(III) (≡Cu(III)) promoted the generation of superoxide radicals (O2•-) with a contribution of up to 72.8 %. Subsequently, nascent ≡Cu(III) and O2•- accelerated the degradation of intermediates. Besides, coexisting organic substances inhibited Cu-EDTA decomplexation, whereas inorganic ions had a weak impact. After five cycles of use, the Calcite/PMS system retained 99.3 % efficiency in decomplexing Cu-EDTA. This investigation provides valuable insights into using calcite to remove HMCs and enhances our comprehension of the decomplexation intermediates accelerating HMCs degradation.

Synergistic degradation of 2,4-dichlorophenoxyacetic acid in water by interfacial pre-reduction enhanced peroxymonosulfate activation derived from novel zero-valent iron/biochar

Iron-based biochar exhibits great potential in degrading emerging pollutants and remediation of water environments. In this study, a highly efficient catalytic Fe0/biochar (MZB-800) was synthesized by the co-pyrolysis of poplar sawdust and K2FeO4 at 800 °C. A novel water purification technology of pre-reduction followed by PMS activation for MZB-800 was proposed to degrade the refractory 2,4-dichlorophenoxyacetic acid (2,4-D) pesticide. The corrosive effect of the strong oxidizing potassium salt endowed the MZB-800 surface with more Fe0 and porous structure, achieving greater 2,4-D adsorption binding energy. The removal efficiency of MZB-800 on 2,4-D was greater than that of biochar (BC) and conventional Fe0/biochar (Fe-BC) prepared by FeCl3·6 H2O as the precursor. The proposed novel water purification technology showed the synergistic effect between the interfacial pre-reduction and the PMS activation derived by MZB-800. Regarding 2,4-D degradation and dechlorination performance, the synergistic coefficient between pre-reduction and subsequent PMS activation for MZB-800 were 2 and 1.4 respectively. Based on the normalized kinetic analysis and the Langmuir-Hinshelwood model, we proposed the underlying mechanism of MZB-800 interfacial pre-reduction and subsequent PMS activation for synergistic removal of 2,4-D. The large amount of Fe2+ and hydroxyl density accumulated by the Fe0 and hydroquinone structures on the MZB-800 surface during the pre-reduction stage provided abundant active sites for the subsequent activation of PMS. The improved activation reaction rate generated more reactive oxygen species, further strengthening the removal efficiency of 2,4-D. This work manifested that the novel water purification technology of pre-reduction/PMS activation of iron-based biochar is feasible for removing emerging pollutants in the water environment. ENVIRONMENTAL IMPLICATION: Extensive abuse of 2,4-dichlorophenoxyacetic acid (2,4-D) herbicide with high solubility and refractory degradation has caused environmental pollution and ecological deterioration. This manuscript described a novel water purification technology, centered on high-efficiency Fe0/biochar and utilizing pre-reduction and PMS reactivation strategies to synergistically degrade 2,4-D, which had strong environmental relevance. By elucidating the synergistic removal mechanism, the research provided valuable insights into removing emerging pollutants, thus promoting environmental sustainability and safeguarding ecosystem health. Overall, it is of high importance to provide a feasible and efficient method for removing hazardous 2,4-D from water environments, which contributes to addressing pressing environmental problems.

Nucleophilic hydrolysis of dichloroacetonitrile and trichloroacetonitrile disinfection byproducts by peroxymonosulfate: Kinetics and mechanisms

In this work, it was found that peroxymonosulfate (PMS) could appreciably accelerate the transformation rates of dichloroacetonitrile (DCAN) and trichloracetonitrile (TCAN) in aqueous solutions, especially under alkaline pHs. The impact of reactive oxygen species scavengers (methyl alcohol for sulfate radical, tert-butyl alcohol for hydroxyl radical, and azide for singlet oxygen) and water matrices (chloride (Cl-), bicarbonate (HCO3-), and natural organic matter (NOM)) on DCAN and TCAN transformation by PMS is evaluated, revealing negligible effects. A nucleophilic hydrolysis pathway, as opposed to an oxidation process, was proposed for the transformation of DCAN and TCAN by PMS, supported by the hydrolyzable characteristics of these compounds and validated through density functional theory calculations. Kinetic analysis indicated that the transformation of DCAN and TCAN by PMS adhered to a second-order kinetic law, with higher reaction rates observed at elevated pH levels within the range of 7.0-10.0. Kinetic modeling incorporating the hydrolytic contributions of water, hydroxyl ion, and protonated and deprotonated PMS (i.e., HSO5- and SO52-) effectively fitted the experimental data. Species-specific second-order rate constants reveal that SO52- exhibited significantly higher reactivity towards DCAN ((1.69 ± 0.22) × 104 M-1h-1) and TCAN ((6.06 ± 0.18) × 104 M-1h-1) compared to HSO5- ((2.14 ± 0.12) × 102 M-1h-1) for DCAN; and (1.378 ± 0.11) × 103 M-1h-1 for TCAN). Comparative analysis of DCAN and TCAN transformation efficiencies by four different oxidants indicated that PMS rivaled chlorine but falls short of hydrogen peroxide, with peroxydisulfate displaying negligible reactivity. Overall, this study uncovers the nucleophilic hydrolysis characteristics of PMS, supplementing its recognized role as an oxidant precursor or mild oxidant, and underscores its significant implications for environmental remediation.

The role of chitosan in promoting the catalytic activity of bismuth ferrite as peroxymonosulfate activator for antibiotics removal

Chitosan possesses electron-rich amino (-NH2) and hydroxyl (-OH) moieties which can anchor with transition metal ions during synthesis. Herein, chitosan was employed as an additive to prepare bismuth ferrite (BFO) via hydrothermal approach. The characterization studies revealed that adding chitosan during BFO synthesis leads to the creation of more oxygen vacancies. The performance of chitosan modified BFO (CMB) was evaluated as peroxymonosulfate (PMS) activator for ciprofloxacin (CIP) removal. Apparently, the addition of 10 wt% chitosan during BFO synthesis (CMB-10) resulted in 1.7 times increase of performance compared to the pristine BFO. Increasing the catalyst loading and PMS dosage resulted in positive effect with 5.7 and 1.9 times rate enhancement, respectively. The CMB-10 exhibited tolerance against pH variation, water matrix, and interfering species. The scavenging experiments indicated that singlet oxygen (1O2), superoxide radicals (O2•-) and sulfate radicals (SO4•-) played a major role in CIP degradation. These reactive oxygen species were generated from PMS activation via Fe3+/Fe2+ and Bi5+/Bi3+ coupling, and oxygen vacancies on the catalyst surface. The CIP degradation pathways were also elucidated based on the detected CIP intermediates. Overall, this study provides insights into the use of chitosan to prepare sustainable materials for pollutants removal via PMS activation.

Ultrasound‒induced facile synthesis of spinel CoFe2O4‒PAC magnetic nanocatalyst for remediation of hypersaline petrochemical wastewater: Degradation mechanism, biodegradability enhancement and phytotoxicity mitigation

In this study, magnetic CoFe2O4-PAC nanocatalysts were synthesized through facile hydrothermal and co‒precipitation approaches with ultrasonic irradiation, which were used for the treatment of hypersaline petrochemical wastewater (HPCW). When an ultrasound‒induced synthesis process (US@CoFe2O4‒PAC) was used, a more efficient and stable magnetic spinel CoFe2O4‒PAC nanocatalyst was developed. The application of this nanocatalyst as a PMS activator, not only caused eradication of 90.4% of chemical oxygen demand (COD) of a HPCW after 90 min reaction time under the optimum conditions (pH 5-6, catalyst dose 1.0 g/L and 1.0 mM PMS), but also led to marginal leaching of iron (314 μg/L) and cobalt (95 μg/L) from the nanocatalyst. Recycling experiments over five consecutive runs showed a negligible decrease (7.2%) in COD removal efficiency which proved the stability and reusability of magnetic US@CoFe2O4-PAC. Two main mechanisms of adsorption and catalytic oxidation processes (homogeneous and heterogeneous PMS) are involved simultaneously in the PMS/US@CoFe2O4-PAC system, which are responsible for the destruction of refractory contaminants of HPCW through the generation of SO4•‒ and OH• radicals. COD of HPCW was mainly removed through SO4•- radical attack (73.6%) and the biodegradability of HPCW was enhanced dramatically after 90 min reaction time. The germination index (GI) of raw HPCW was increased 17.1 ± 4.2% and 24.3 ± 8.8% after 15 and 90 min reaction time, respectively, even PMS/US@CoFe2O4-PAC system showed less impact on phytotoxicity mitigation. Hence, it can be recommended to dilute the effluent before using for irrigational purpose. The findings of this study present practical significance of spinel US@CoFe2O4-PAC, which is an environment‒friendly catalyst, easy to handle and can sustain long‒term operation for the treatment of recalcitrant hypersaline wastewater and the other potential practical applications.

Amphichdiral enhancement on singlet oxygen generation and stable thallium immobilization using iron-driven copper oxide

Thallium (Tl) as a prominent priority contaminant in aquatic environment necessitates rigorous regulation. However, limited horizon devotes the impact of selective oxidation on the process of thallium purification. In this study, selective active radical of singlet oxygen (1O2) was continually generated for Tl(Ⅰ) oxidation accomplished with efficient Tl(Ⅲ) immobilization using iron-driven copper oxide (CuFe)/peroxymonosulfate (PMS). Fe-doping changed the active center of electronic structure for enhancing the catalytic and adsorptive reactivities, and installed magnetism for solid-liquid separation. Rapid reaction rate (0.253 min-1) coupled with vigorous elimination efficiency (98.32%) relied on electrostatic attraction, surface complexation, and H-bond interaction. EPR and XPS analyses demonstrated that the synergistic effects of ≡ Cu(Ⅰ)/≡Cu(Ⅱ) and ≡ Fe(Ⅲ)/≡Fe(Ⅱ) redounded to the sustained generation of 1O2 through the pathway of PMS → •O2- → 1O2, and 1O2 exploited an advantage to selectively oxidize Tl(Ⅰ) to Tl(Ⅲ). 3D isosurface cubic charts revealed that the immobilizing ability of Tl(Ⅲ) hydrate for CuFe was notably superior to that of Tl(Ⅲ) hydrate for CuO and Tl(Ⅰ) hydrate for CuO/CuFe, which further attested surface reactivity promoted stable immobilization form. This work develops the continuous generation of 1O2 and stable immobilization with the goal of efficiently cleansing Tl-containing wastewater.

Simultaneous enhanced antibiotic pollutants removal and sustained permeability of the membrane involving CoFe2O4/MoS2 catalyst initiated with simple H2O2 backwashing

Membranes for wastewater treatment should ideally exhibit sustainable high permeate production, enhanced pollutant removal, and intrinsic physical rejection. In this study, CoFe2O4/MoS2 serves as a non-homogeneous phase catalyst; it is combined with polyether sulfone membranes via liquid-induced phase separation to simultaneously sustain membrane permeability and enhance antibiotic pollutant degradation. The prepared catalytic membranes have higher pure water flux (329.34 L m-2 h-1) than pristine polyethersulfone membranes (219.03 L m-2 h-1), as well as higher mean pore size, porosity, and hydrophilicity. Under a moderate transmembrane pressure (0.05 MPa), tetracycline (TC) in synthetic and real wastewater was degraded by the optimal catalytic membrane by 72.7 % and 91.2 %, respectively. Owing to the generation of the reactive oxygen species (ROS) during the Fenton-like reaction process, the catalytic membrane could exclude the natural organics during the H2O2 backwash step and selectively promote fouling degradation in the membrane channel. The irreversible fouling ratio of the catalyzed membrane was significantly reduced, and the flux recovery rate increased by up to 91.6 %. A potential catalytic mechanism and TC degradation pathways were proposed. This study offers valuable insights for designing catalytic membranes with enhanced filtration performance.

A review on recent advancements in the treatment of polyaromatic hydrocarbons (PAHs) using sulfate radicals based advanced oxidation process

Polyaromatic hydrocarbons (PAHs) are the most persistent compounds that get contaminated in the soil and water. Nearly 16 PAHs was considered to be a very toxic according US protection Agency. Though its concentration level is low in the environments but the effects due to it, is enormous. Advanced Oxidation Process (AOP) is an emergent methodology towards treating such pollutants with low and high molecular weight of complex substances. In this study, sulfate radical (SO4‾•) based AOP is emphasized for purging PAH from different sources. This review essentially concentrated on the mechanism of SO4‾• for the remediation of pollutants from different sources and the effects caused due to these pollutants in the environment was reduced by this mechanism is revealed in this review. It also talks about the SO4‾• precursors like Peroxymonosulfate (PMS) and Persulfate (PS) and their active participation in treating the different sources of toxic pollutants. Though PS and PMS is used for removing different contaminants, the degradation of PAH due to SO4‾• was presented particularly. The hydroxyl radical (•OH) mechanism-based methods are also emphasized in this review along with their limitations. In addition to that, different activation methods of PS and PMS were discussed which highlighted the performance of transition metals in activation. Also this review opened up about the degradation efficiency of contaminants, which was mostly higher than 90% where transition metals were used for activation. Especially, on usage of nanoparticles even 100% of degradation could be able to achieve was clearly showed in this literature study. This study mainly proposed the treatment of PAH present in the soil and water using SO4‾• with different activation methodologies. Particularly, it emphasized about the importance of treating the PAH to overcome the risk associated with the environment and humans due to its contamination.

Freezing-enhanced degradation of azo dyes in the chloride-peroxymonosulfate system

In this study, we investigated the freezing-induced acceleration of dye bleaching by chloride-activated peroxymonosulfate (PMS). It has been observed that the oxidation of chloride by PMS generates a free chlorine species, such as hypochlorous acid (HOCl), under mild acidic and circumneutral pH condition. This process is the major reason for the enhanced oxidation capacity for electron-rich organic compounds (e.g., phenol) in the chloride-PMS system. However, we demonstrated that the chloride-PMS system clearly reduced the total organic carbon concentration (TOC), whereas the HOCl system did not lead to decrease in TOC. Overall, the chemical reaction is negligible in an aqueous condition if the concentrations of reagents are low, and freezing the solution accelerates the degradation of dye pollutants remarkably. Most notably, the pseudo-first order kinetic rate constant for acid orange 7 (AO7) degradation is approximately 0.252 h-1 with 0.5 mM PMS, 1 mM NaCl, initial pH 3, and a freezing temperature of -20 °C. AO7 degradation is not observed when the solution is not frozen. According to a confocal Raman-microscope analysis and an experiment that used an extremely high dose of reactants, the freeze concentration effect is the main reason for the acceleration phenomenon. Because the freezing phenomenon is spontaneous at high latitudes and at mid-latitudes in winter, and the chloride is ubiquitous elsewhere, the frozen chloride-PMS system has potential as a method for energy-free and eco-friendly technology for the degradation of organic pollutants in cold environments.

Resource utilization of medical waste incineration fly ash to activate peroxydisulfate for tetracycline degradation: Synergy between adsorption and PDS activation

Medical waste incineration fly ash (MWI FA) is classified as a hazardous solid waste. Therefore, the development of recycling technologies to convert MWI FA into useful products is necessary and challenging. In this study, we developed a sustainable approach for preparing a catalyst through the pyrolysis of water-washed MWI FA (WW FA-x, where x corresponds to the pyrolysis temperature). Subsequently, it was applied as a potent peroxydisulfate (PDS) activator to remove tetracycline (TC) from water. The results showed that the WW FA-800 exhibited remarkable adsorption performance as well as highly efficient catalytic activation of PDS, with a 115 mg/g maximum TC adsorption capacity and 93.5% (reaction kinetic rate = 315 μmol/g/h) TC removal within 60 min. A synergistic effect was achieved by adsorption and PDS activation. TC degradation was primarily driven by non-radical (1O2 and electron transfer) processes. WW FA-800 possesses multiple active sites, including defects, π-π*, O-CO groups, Fe0, and Cu(I). Three possible pathways for TC decomposition have been proposed, with the majority of intermediates exhibiting less toxicity than TC. Furthermore, the WW FA/PDS system exhibited an excellent anti-interference ability, and universality in the degradation of various organic contaminants. Notably, energy consumption was minimal, approximately 2.80 kWh/(g·TC), and the leachability of heavy metals in the WW FA-800 was within acceptable limits. This study provides a MWI FA recycling route for the development of highly active catalysts.

Were Persulfate-Based Advanced Oxidation Processes Really Understood? Basic Concepts, Cognitive Biases, and Experimental Details

Persulfate (PS)-based advanced oxidation processes (AOPs) for pollutant removal have attracted extensive interest, but some controversies about the identification of reactive species were usually observed. This critical review aims to comprehensively introduce basic concepts and rectify cognitive biases and appeals to pay more attention to experimental details in PS-AOPs, so as to accurately explore reaction mechanisms. The review scientifically summarizes the character, generation, and identification of different reactive species. It then highlights the complexities about the analysis of electron paramagnetic resonance, the uncertainties about the use of probes and scavengers, and the necessities about the determination of scavenger concentration. The importance of the choice of buffer solution, operating mode, terminator, and filter membrane is also emphasized. Finally, we discuss current challenges and future perspectives to alleviate the misinterpretations toward reactive species and reaction mechanisms in PS-AOPs.

Degradation of organic pollutants by the Cl-/PMS process

The viewpoints on whether high concentrations of chloride ion (Cl-) promote or inhibit the oxidation activity of activated persulfates are still inconclusive. Furthermore, the degradation of organic pollutants by the persulfates in the presence of high Cl- concentrations without any activation medium has not yet been studied. In this work, the efficiency and mechanism of degradation of organic pollutants such as carbamazepine (CBZ), sulfadiazine (SDZ), and phenol (PN) by Cl--activated PMS (denoted as Cl-/PMS) were investigated. Results showed that Cl- could effectively activate PMS for the complete removal of CBZ, SDZ, and PN with reaction kinetic constants of 0.4516 min-1, 0.01753 min-1, and 0.06805 min-1, respectively. Parameters such as PMS dose, Cl- concentration, solution pH, and initial concentrations of organic pollutants that affect the degradation efficiencies of the Cl-/PMS process were optimized. Unlike conventional activated persulfates, it was confirmed that the free chlorine was the main active species in the Cl-/PMS process. Finally, the degradation by-products of CBZ and SDZ as well as their toxicity were detected, and a possible degradation pathway for CBZ and SDZ was proposed. Though higher toxic chlorinated by-products were generated, the Cl-/PMS process was still an efficient oxidation method for the removal of organic pollutants in aqueous solutions which contain high concentrations of Cl-.

Photo-electrochemical activation of persulfate for the simultaneous degradation of microplastics and personal care products

The recent widespread use of microplastics (MPs), especially in pharmaceuticals and personal care products (PPCPs), has caused significant water pollution. This study presents a UV/electrically co-facilitated activated persulfate (PS) system to co-degrade a typical microplastic polyvinyl chloride (PVC) and an organic sunscreen p-aminobenzoic acid (PABA). We investigated the effect of various reaction conditions on the degradation. PVC and PABA degradation was 37% and 99.22%, respectively. Furthermore, we observed alterations in the surface topography and chemical characteristics of PVC throughout degradation. The possible degradation pathways of PVC and PABA were proposed by analyzing the intermediate products and the free radicals generated. This study reveals the co-promoting effect of multiple mechanisms in the activation by ultraviolet light and electricity.

LaCoO3/SBA-15 as a high surface area catalyst to activate peroxymonosulfate for degrading atrazine in water

An efficient perovskite-based heterogeneous catalyst is highly desired to activate peroxymonosulfate (PMS) for removing organic pollutants in water. A high surface area PMS-activator was fabricated by loading LaCoO3 on SBA-15 to degrade atrazine (ATR) in water. The LaCoO3/SBA-15 depicted better textural properties and higher catalytic activity than LaCoO3. In 6.0 min, atrazine (ATZ) degradation in the selected LaCoO3/SBA-15/PMS system, LaCoO3, adsorption by LaCoO3/SBA-15, sole PMS processes reached approximately 100%, 55.15%, 12.80%, and 16.65 % respectively. Furthermore, 0.04 mg L-1 Co was leached from LaCoO3/SBA-15 during PMS activation by LaCoO3/SBA-15. The LaCoO3/SBA-15 showed stable catalytic activity after reuse. The use of radical scavengers and electron paramagnetic resonance spectroscopy (EPR) demonstrated that ROS such as 1O2, O2•-, •OH, and SO4•- were generated by PMS activated by LaCoO3/SBA-15 owing to redox reactions [Co2+/Co3+, and O2-/O2]. EPR, XPS, ATR-FTIR, EIS, LSV, and chronoamperometric measurements were used to explain the catalytic mechanism for PMS activation. Excellent atrazine degradation was due to high surface area, porous nature, diffusion-friendly structure, and ROS. Our investigation proposes that perovskites with different A and B metals and modified perovskites can be loaded on high surface area materials to activate PMS into ROS.

Facile synthesis of pyrite FeS2 on carbon spheres for high-efficiency Fenton-like reaction

Designing iron-based catalysts for Fenton-like reactions with peroxymonosulfate (PMS) as oxidants have attracted growing attentions. Herein, pyrite FeS2 supported on carbon spheres (FeS2@C) is synthesized by a facile low-temperature method. The FeS2@C/PMS system can degrade carbamazepine (CBZ) effectively in a wide pH range. Sulfate radicals (SO4·-), hydroxyl radicals (·OH), superoxide radical (O2·-), and singlet oxygen (1O2) are the responsible reactive oxygen species (ROSs) for CBZ degradation. Moreover, in the simulated fixed-bed reactor, the FeS2@C/PMS system can maintain a high CBZ removal ratio of >95% for than 8 h, exhibiting its excellent stability. The outstanding performance of FeS2@C/PMS system is attributed to the presence of carbon spheres and lattice S2-, which together promote the Fe(III)/Fe(II) redox cycle. The FeS2@C is a promising catalyst due to its facile synthesis, low cost, high efficiency, and excellent stability to activate PMS for organics degradation.

Role of biochar in superoxide-dominated dye degradation in catalyst-activated peroxymonosulphate process

In recent times, the application of biochar (BC) as an upcoming catalyst for the elimination of recalcitrant pollutants has been widely explored. Here, an iron loaded bamboo biochar activated peroxymonosulphate (PMS) process was tested for removing Congo red (CR) dye from water medium. The catalyst was synthesized using a green synthesis method using neem extracts and characterized using SEM, FTIR, and XRD. The effects of various operating parameters, including solution pH, catalyst dosage, and pollutant dosage, on dye degradation efficiency were examined. The results showed that at the optimized conditions of 300 mg L-1 PMS concentration, 200 mg L-1 catalyst dosage, and pH 6, about 89.7% of CR dye (initial concentration 10 ppm) was removed at 60 min of operation. Scavenging experiments revealed the significant contribution of O2•-, •OH, and 1O2 for dye degradation, with a major contribution of O2•-. The activation of PMS was mainly done by biochar rather than iron (loaded on biochar). The catalyst was highly active even after four cycles.

Research progress of persulfate activation technology

Persulfate-based advanced oxidation processes (PS-AOPs) have been widely investigated by academia and industry due to their high efficiency and selectivity for the removal of trace organic pollutants from complex water substrates. PS-AOPs have been extensively studied for the degradation of pesticides, drugs, halogen compounds, dyes, and other pollutants. Utilizing bibliometric statistics, this review presents a comprehensive overview of persulfate-based advanced oxidation technology research over the past decade. The number of published articles about persulfate activation has steadily increased during this time, reflecting extensive international collaboration. Furthermore, this review introduces the most widely employed strategies for persulfate activation reported in the past 10 years, including carbon material activation, photocatalysis, transition metal activation, electrochemical activation, ultrasonic activation, thermal activation, and alkali activation. Next, the potential activation mechanisms and influencing factors, such as persulfate dosage during activation, are discussed. Finally, the application of PS-AOPs in wastewater treatment and in situ groundwater treatment is examined. This review summarizes the previously reported experiences of persulfate-based advanced oxidation technology and presents the current application status of PS-AOPs in organic pollution removal, with the aim of avoiding misunderstandings and providing a solid foundation for future research on the removal of organic pollutants.

Synergistic oxidation induced by underwater bubbling plasma and diatomite-CoFe2O4 activated peroxymonosulfate for the degradation of ciprofloxacin hydrochloride

Underwater bubbling plasma (UBP) coupled with diatomite-CoFe2O4 (Dt-CFO) activated peroxymonosulfate (PMS) was proposed for the degradation of ciprofloxacin hydrochloride (CIP) in this work. The catalyst sample of Dt-CFO with large specific surface area, rich active sites and excellent magnetic property was prepared by the hydrothermal method and systematically characterized to investigate its material properties. The combination of UBP and Dt-CFO activated PMS (UBP/Dt-CFO/PMS) showed excellent synergy with the synergistic factor of 1.98, and reached the CIP degradation percentage of 94.7%, which corresponded to the kinetic constant of 0.097 min-1. Dt-CFO with the diatomite content of 30 wt% achieved the best catalytic activity in the reaction system. Higher catalyst and PMS dose, peak voltage, pulse frequency and lower initial CIP concentration were beneficial for CIP removal. The addition of Cl-, HCO3-, SO42- and humic acid suppressed CIP degradation, while NO3- had no effect on CIP removal. The Dt-CFO composite exhibited excellent reusability and low leaching metal amount, demonstrating its good stability. SO4-·, ·OH, ·O2-, 1O2, eaq, O3 and H2O2 were the active species confirmed to be involved in CIP degradation. The redox circles of ≡ Co(Ⅱ)/≡Co(Ⅲ) and ≡ Fe(Ⅱ)/≡Fe(Ⅲ) on Dt-CFO surface and the plasma-induced physicochemical effects dominated PMS activation. The decomposition process of CIP was explored through fluorescence spectra. Three degradation pathways were inferred, and the toxicity analysis showed the toxicity of CIP solution weakened after discharge treatment.

Removal of tetracycline by ultraviolet/sodium percarbonate (UV/SPC)advanced oxidation process in water

Tetracycline (TC) was widely used and frequently detected in various water bodies, where the presence of TC posed a significant threat to the health of aquatic organisms. Furthermore, antibiotics were hardly degraded by biological treatment. Thus, in order to enhance the removal of TC, we proposed the use of a novel ultraviolet/sodium percarbonate (UV/SPC) advanced oxidation process and initiated an in-depth study. The study investigated the influence of oxidant dosage, initial pH, UV intensity, and TC concentration on the removal of TC. The results demonstrated that the UV/SPC system efficiently removed TC, with removal efficiency increasing as the SPC concentration increased. Within the pH range of 3-11, TC degradation exhibited minimal variation, indicating the UV/SPC system's strong adaptability to pH variations. The research on the impact of the water matrix on TC removal revealed that HCO3- had an inhibitory effect on TC degradation, while NO3- promoted TC degradation. Additionally, the presence of free radical species (·OH, ·CO3-, ·O2-) were detected and rate constants for the secondary reactions (k·OH,TC = 6.3 × 109 L mol-1·s-1, k·CO3-,TC = 3.4 × 108 L mol-1·s-1) were calculated, indicating that ·OH exhibited a stronger oxidative performance compared to ·CO3-. This study did not only present a novel strategy via UV/SPC to remove TC but also uncovered the unique role of ·CO3- for contaminant removal.

Trace Co(II) triggers peracetic acid activation in phosphate buffer: New insights into the oxidative species responsible for ciprofloxacin removal

Peracetic acid (PAA) emerges as a promising disinfectant and oxidant applied worldwide, and its application has been broadened for advanced oxidation processes (AOPs) in wastewater treatment. Current studies on transition metal-activated AOPs utilized relatively high concentrations of catalysts, leading to potential secondary pollution concerns. This study boosts the understanding of reaction mechanism in PAA activation system under a low-level concentration. Herein, trace levels of Co(II) (1 μM) and practical dosages of PAA (50-250 μM) were employed, achieving noticeable ciprofloxacin (CIP) degradation efficiencies (75.8-99.0%) within 20 min. Two orders of magnitude of the CIP's antibacterial activity significantly decreased after Co(II)/PAA AOP treatment, which suggested the effective ecological risk control capability of the reaction system. The degradation performed well in various water matrices and the primary reactive species is proposed to be CoHPO4-OO(O)CCH3 complexes with scavenging tests and electron paramagnetic resonance tests. The degradation pathway of fluoroquinolones including piperazine ring-opening (dealkylation and oxidation), defluorination, and decarboxylation, were systematically elucidated. This study boosts a comprehensive and novel understanding of PAA-based AOP for CIP degradation.

Advanced degradation of organic pollutants using sonophotocatalytic peroxymonosulfate activation with CoFe2O4/Cu- and Ce-doped SnO2 composites

The rampant upsurge of organic pollutants in aqueous media has become one of the major concerns nowadays. Finding non-specific catalysts that can target a wide range of organic pollutants is a key challenge. Eco-friendly oxidative radicals, such as promoted by peroxymonosulfate (PMS), are necessary for efficient water decontamination. We propose a multicomponent composite catalyst for activating PMS using a dual strategy of sonophotocatalysis. The composite integrates cobalt ferrite and Cu- or Ce-doped SnO2, with the at. % of doping metal and the mixture ratio carefully balanced. The top-performing architectures were able to decompose rhodamine B (20 ppm), a representative pollutant, in under 3 min and achieve over 70% mineralization in just 5 min. The synthesized nanocomposites demonstrated exceptional sonophotocatalytic performance, even when treating complex and diverse multipollutant solutions (80 ppm), achieving over 75% mineralization after 150 min. Considering their high stability and reusability, the proposed CoFe2O4/Cu- and Ce-doped SnO2 materials are among the state-of-the-art heterogeneous catalysts for mineralizing organic pollutants through PMS activation.

Degradation mechanisms and toxicity determination of bisphenol A by FeOx-activated peroxydisulfate under ultraviolet light

Ultraviolet light (UV)-assisted advanced oxidation processes (AOPs) are commonly used to degrade organic contaminants. However, this reaction system's extensive comprehension of the degradation mechanisms and toxicity assessment remains inadequate. This study focuses on investigating the degradation mechanisms and pathways of bisphenol A (BPA), generation of reactive oxygen species (ROS), and toxicity of degradation intermediates in UV/PDS/ferrous composites (FeOx) systems. The degradation rate of BPA gradually increased from the initial 11.92% to 100% within 120 min. Sulfate radicals (SO 4 . - ), hydroxyl radicals (.OH), superoxide anions (O 2 . - ), and singlet oxygen (1O2) were the primary factors in the photocatalytic degradation of BPA in the UV/PDS/FeOx systems. The main reactions of BPA in this system were deduced to be β-bond cleavage, hydroxyl substitution reaction, hydrogen bond cleavage, and oxidation reaction. A trend of decreasing toxicity for the degradation intermediates of BPA was observed according to the toxicity investigations. The efficient degradation of BPA in UV/PDS/FeOx systems provided theoretical data for AOPs, which will improve the understanding of organic contaminants by FeOx in natural industry wastewater.

Synthesis of CaCO3 supported nano zero-valent iron-nickel nanocomposite (nZVI-Ni@CaCO3) and its application for trichloroethylene removal in persulfate activated system

Nano zero-valent (nZVI) based composite have been widely utilized in environmental remediation. However, the rapid agglomeration and quick deactivation of nZVI limited its application on large scale. In this work, CaCO3 supported nZVI-Ni catalyst, namely nZVI-Ni@CaCO3 was prepared and used for the efficient removal of trichloroethylene (TCE) in PS oxidation process. The successful disbursement of nZVI-Ni on CaCO3 support material not only increased the surface area of nZVI-Ni@CaCO3 (69.45 m2/g) with respect to CaCO3 (5.92 m2/g) and bare nZVI (13.29 m2/g) but also improved the catalytic activity. XRD, XPS and FTIR analysis confirmed the successful formation of nZVI-Ni@CaCO3 nanoparticles. The nZVI-Ni@CaCO3 nanoparticles combined with PS had achieved complete removal of TCE (99.8%) with dosage of 36 mg/L and 1.34 mM respectively. These results showed that the use of CaCO3 as support material for nZVI-Ni could have significant influence on contaminant removal process. Scavenging and EPR tests validated the existence of SO4•-, OH• and O2•- radicals in PS/nZVI-Ni@CaCO3 system and highlighted the dominant role of SO4•- radicals in TCE removal process. HCO3- ions and humic acid have shown adverse effect on TCE removal due to radical scavenging and buffering effect. Owing to improved catalytic activity and easy preparation, the nZVI-Ni@CaCO3 nanoparticles could be served as an alternative strategy for environmental remediation.

Converting peracetic acid activation by Fe3O4 from nonradical to radical pathway via the incorporation of L-cysteine

Recently, peracetic acid (PAA) based Fenton (-like) processes have received much attention in water treatment. However, these processes are limited by the sluggish Fe(III)/Fe(II) redox circulation efficiency. In this study, L-cysteine (L-Cys), an environmentally friendly electron donor, was applied to enhance the Fe3O4/PAA process for the sulfamethoxazole (SMX) abatement. Surprisingly, the L-Cys incorporation was found not only to enhance the SMX degradation rate constant by 3.2 times but also to switch the Fe(IV) dominated nonradical pathway into the •OH dominated radical pathway. Experiment and theoretical calculation result elucidated -NH2, -SH, and -COOH of L-Cys can increase Fe solubilization by binding to the Fe sites of Fe3O4, while -SH of L-Cys can promote the reduction of bounded/dissolved Fe(III). Similar SMX conversion pathways driven by the Fe3O4/PAA process with or without L-Cys were revealed. Excessive L-Cys or PAA, high pH and the coexisting HCO3-/H2PO4- exhibit inhibitory effects on SMX degradation, while Cl- and humic acid barely affect the SMX removal. This work advances the knowledge of the enhanced mechanism insights of L-Cys toward heterogeneous Fenton (-like) processes and provides experimental data for the efficient treatment of sulfonamide antibiotics in the water treatment.

Degradation of refractory organic matter in MBR effluent from treating landfill leachate by UV/PMS and UV/H2O2: a comparative study

This study applied ultraviolet/peroxymonosulfate (UV/PMS) and UV/hydrogen peroxide (UV/H2O2) processes to the advanced treatment of membrane bioreactor (MBR) effluent. The degradation efficiency of refractory organic matter and the reaction mechanisms of the two processes were systematically investigated. The results showed that the degradation efficiency of the UV/PMS processes was significantly lower than that of the UV/H2O2 process when the PMS concentration was significantly lower than the H2O2 concentration, e.g. the UV254 removals under optimal conditions were 72.92% and 82.21%, respectively. Additionally, the UV/PMS process could operate over a broader pH range. The degradation efficiency of the UV/PMS process was slightly increased by HCO3- and Cl- due to the activation of PMS, while in the UV/H2O2 process, HCO3- and Cl- depressed the degradation efficiency by competing with organic matter to react with reactive oxygen species (ROS). After the two processes, the aromaticity, humification, condensation degree, and molecular weight of refractory organic matter in the MBR effluent were considerably decreased. Fulvic- (HA) and humic-like substances (FA) were greatly degraded by the two processes. The UV/PMS had a superior degradation efficiency for macromolecular HA in the early stage of the reaction, and the UV/H2O2 could degrade HA to protein-like substances in the latter stage of the reaction. These differences between the two processes could be attributed to the dominance of different ROS, with SO4•- and HO• dominating in the UV/PMS, and HO• dominating in the UV/H2O2. The results of this study provide theoretical support for the application of MBR effluent treatment.Highlights Comparison on the MBR effluent treatment of UV/PMS and UV/H2O2 is studied.UV/PMS process can better destroy humic-like substances in the early reaction stage.Humic-like substances are transformed into protein-like compounds in UV/H2O2 process.UV/PMS and UV/PMS performs differently due to their different dominant ROS.

Insights into the mechanism of multiple Cu-doped CoFe2O4 nanocatalyst activated peroxymonosulfate for efficient degradation of Rhodamine B

The multiple metal catalyst as a promising nanomaterial has shown excellent activity in the peroxymonosulfate (PMS) activation for pollutant degradation. However, the role of special sites and in-depth understanding of the PMS activation mechanism are not fully studied. In this study, a Cu-doped CoFe2O4 nanocatalyst (0.5CCF) was synthesized by a sol-gel and calcination method, and used for PMS activation to remove Rhodamine B (RhB). The results showed that the Cu doping obviously enhanced the catalytic performance of CoFe2O4, with 99.70% of RhB removed by 0.5CCF while 74.91% in the CoFe2O4 within 15 min. Based on the X-ray photoelectron spectroscopy and electrochemical analysis, this could be ascribed to the more low valence of Co and Fe species generated on the 0.5CCF and faster electron transfers occurred in the 0.5CCF due to the Cu doping. In addition, Cu doping could provide more reaction sites for the 0.5CCF to activate PMS for RhB removal. The metal species and the surface hydroxyl were the reaction sites of PMS activation, and the surface hydroxyl played an important role in surface-bound reactive species generation. During the PMS activation, the Cu not only activated PMS to produce reactive oxygen species (ROS), but also regenerated Co2+ and Fe2+ to accelerate the PMS activation. The non-radical of 1O2 was the main ROS with a 99.35% of contribution rate, and the SO5•- self-reaction was its major source. This study provides a new insight to enhance the PMS activation performance of multiple metal catalysts by Cu doping in wastewater treatment.

Degradation of triclosan by peroxydisulfate/peroxomonosulfate binary oxidants activation under thermal conditions: Efficiency and mechanism

Peroxydisulfate (PDS) and peroxymonosulfate (PMS) could be efficiently activated by heat to generate reactive oxygen species (ROS) for the degradation of organic contaminants. However, defects including the inefficiency treatment and pH dependence of monooxidant process are prominent. In this study, synergy of heat and the PDS-PMS binary oxidant was studied for efficient triclosan (TCS) degradation and apply in rubber wastewater. Under different pH values, the degradation of TCS followed pseudo-first-order kinetics, the reaction rate constant (kobs) value of TCS in heat/PDS/PMS system increased from 1.8 to 4.4 fold and 6.8-49.1 fold when compared to heat/PDS system and heat/PMS system, respectively. Hydroxyl radicals (·OH), sulfate radicals (SO4·-) and singlet oxygen (1O2) were the major ROS for the degradation of TCS in heat/PDS/PMS system. In addition, the steady-state concentrations of ·OH/1O2 and SO4·-/·OH/1O2 increased under acidic conditions and alkaline conditions, respectively. It was concluded that the pH regulated the ROS for degradation of TCS in heat/PDS/PMS system significantly. Based on the analysis of degradation byproducts, it was inferred that the dechlorination, hydroxylation and ether bond breaking reactions occurred during the degradation of TCS. Moreover, the biological toxicity of the ten byproducts was lower than that of TCS was determined. Furthermore, the heat/PDS/PMS system is resistant to the influence of water substrates and can effectively improve the water quality of rubber wastewater. This study provides a novel perspective for efficient degradation of TCS independent of pH in the heat/PDS/PMS system and its application of rubber wastewater.

Dynamic defects boost in-situ H2O2 piezocatalysis for water cleanup

Creating efficient catalysts for simultaneous H2O2 generation and pollutant degradation is vital. Piezocatalytic H2O2 synthesis offers a promising alternative to traditional methods but faces challenges like sacrificial reagents, harsh conditions, and low activity. In this study, we introduce a cobalt-loaded ZnO (CZO) piezocatalyst that efficiently generates H2O2 from H2O and O2 under ultrasonic (US) treatment in ambient aqueous conditions. The catalyst demonstrates exceptional performance with ~50.9% TOC removal of phenol and in situ generation of 1.3 mM H2O2, significantly outperforming pure ZnO. Notably, the CZO piezocatalyst maintains its H2O2 generation capability even after multiple cycles, showing continuous improvement (from 1.3 mM to 1.8 mM). This is attributed to the piezoelectric electrons promoting the generation of dynamic defects under US conditions, which in turn promotes the adsorption and activation of oxygen, thereby facilitating efficient H2O2 production, as confirmed by EPR spectrometry, XPS analysis, and DFT calculations. Moreover, the CZO piezocatalysts maintain outstanding performance in pollutant degradation and H2O2 production even after long periods of inactivity, and the deactivated catalyst due to metal ion dissolution could be rejuvenated by pH adjustment, offering a sustainable solution for wastewater purification.

Novel calcium oxide activated peroxymonosulfate system for methylene blue removal: Identification of key influencing factors, transformation pathway and toxicity assessment

The activation of peroxymonosulfate (PMS) has gained significant interest in the removal of organic pollutants. However, traditional methods usually suffer from drawbacks such as secondary contamination and high energy requirements. In this study, we propose a green and cost-effective approach utilizing calcium oxide (CaO) to activate PMS, aiming to construct a simple and reliable PMS based advanced oxidation processes (AOPs). The proposed CaO/PMS system achieved fast degradation of methylene blue (MB), where the degradation rate of CaO/PMS system (0.24 min-1) was nearly 2.67 times that of PMS alone (0.09 min-1). Under the optimized condition, CaO/PMS system exhibited remarkable durability against pH changes, co-exists ions or organic matters. Furthermore, singlet oxygen (1O2) was identified as the dominant reactive oxygen species by electron paramagnetic resonance (EPR) and quenching tests. Accordingly, the degradation pathways of MB are proposed by combing the results of LC/MS analysis and density functional theory (DFT) calculations, and the predicted ecotoxicity of the generated byproducts evaluated by EOCSAR could provide systematic insights into the fates and environmental risks of MB. Overall, the study provides an eco-friendly and effective strategy for treating dyeing wastewater, which should shed light on the application of PMS based AOPs.

Insights into the potential applications of permanganate/peroxymonosulfate systems: enhancement via amorphous MnO2, effects of water matrices, and optimization using response surface methodology

In this study, we developed a novel self-catalytic oxidation system involving peroxymonosulfate (PMS) and permanganate (KMnO4), named as CUPP, to efficiently mineralize sulfamethoxazole (SMX) in groundwater. It was found that amorphous MnO2 derived from the in situ reduction of KMnO4 can directly adsorb HSO5-, a complex hydroxyl group, mediate the internal disproportionation reaction of HSO5- with the manganese complex, and effectively activate PMS, thereby promoting the oxidation of SMX and its degradation intermediates through sulfonate radiation. Furthermore, by using electron spin resonance (EPR), HPLC/MS full scan, and response surface methodology, the coexistence of HO˙, SO4-˙, O2-˙, 1O2, and active chlorine (Cl2, HOCl) in the CUPP system was confirmed. A total of 24 intermediate products were detected, and four possible degradation pathways were identified for SMX. In addition, it was found that the CUPP system has a strong impact resistance to pH variations, groundwater anions, and natural organic matter stress. Undoubtedly, the CUPP system presents an innovative approach for the degradation of various emerging organic pollutants in groundwater.

Enhanced electron-transfer for peroxymonosulfate activation by Ni single sites adjacent to Ni nanoparticles

Oriented generation of specific reactive oxygen species (ROS) has been challenging in peroxymonosulfate (PMS)-based advanced oxidation processes (AOPs). In this work, we constructed a multifunctional catalyst composed of Ni NPs embedded in N-doped carbon nanotubes (NCNTs) with exposed Ni single-atom sites (Ni-NCNTs). The Ni-N4 single sites adjacent to the Ni NPs are more efficient for PMS adsorption and activation, resulting in enhanced production of singlet oxygen (1O2). More interesting, we demonstrated that the superoxide anion radical (O2•-) was generated from 1O2 reduction via the electron transfer from the graphitic-N sites of Ni-NCNTs rather than from O2 reduction or PMS decomposition as reported in previous studies. Thus, Ni-NCNTs can act as both electron acceptor and donor to trigger the cascade production of 1O2 and O2•-, respectively, leading to fast and selective degradation of aqueous organic pollutants. The graphitic-N adjacent to the aromatic π-conjugation of NCNTs facilitated chemisorption of 1O2 onto NCNTs via the strong π*-π interactions, and more importantly, donated the lone pair electrons to trigger the reduction of 1O2 to O2•-. This study unravels the mechanisms for enhanced production of ROS in the nanoconfined Fenton-like systems and shed new light on the application of multifunctional nanocatalyst for rapid wastewater decontamination.

Singlet oxygen: Properties, generation, detection, and environmental applications

Singlet oxygen (1O2) is molecular oxygen in the excited state with high energy and electrophilic properties. It is widely found in nature, and its important role is gradually extending from chemical syntheses and medical techniques to environmental remediation. However, there exist ambiguities and controversies regarding detection methods, generation pathways, and reaction mechanisms which have hindered the understanding and applications of 1O2. For example, the inaccurate detection of 1O2 has led to an overestimation of its role in pollutant degradation. The difficulty in detecting multiple intermediate species obscures the mechanism of 1O2 production. The applications of 1O2 in environmental remediation have also not been comprehensively commented on. To fill these knowledge gaps, this paper systematically discussed the properties and generation of 1O2, reviewed the state-of-the-art detection methods for 1O2 and long-standing controversies in the catalytic systems. Future opportunities and challenges were also discussed regarding the applications of 1O2 in the degradation of pollutants dissolved in water and volatilized in the atmosphere, the disinfection of drinking water, the gas/solid sterilization, and the self-cleaning of filter membranes. This review is expected to provide a better understanding of 1O2-based advanced oxidation processes and practical applications in the environmental protection of 1O2.

Catalytic ozonation of bisphenol A by Cu/Mn@γ-Al2O3: Performance evaluation and mechanism insight

Herein, an alumina-based bimetallic catalyst (Cu1Mn7@γ-Al2O3) was synthesized for bisphenol A (BPA) degradation in the catalytic ozonation process. The catalytic ozonation system could degrade 93.9% of BPA within 30 min under the conditions of pH = 7.0, 10 mg L-1 O3 concentration, and 24 g L-1 catalyst dosage compared to ozone alone (21.0%). The enhanced BPA degradation efficiency was attributed to the abundant catalytic sites and synergistic effects of Cu and Mn. The results revealed that the synergistic interaction between Cu and Mn effectively accelerated the electron transfer process on the catalyst surface, thus promoting the generation of reactive oxygen species (ROS). Further studies indicated that the BPA degradation in Cu1Mn7@γ-Al2O3/O3 system predominantly followed the ·OH and O2·- oxidation pathway. Based on the density functional theory (DFT) calculations and intermediates detected by LC-MS analysis, two pathways for BPA degradation in the Cu1Mn7@γ-Al2O3/O3 system were proposed. The toxicity estimation illustrated that the toxicity of BPA and its byproducts was effectively reduced in the Cu1Mn7@γ-Al2O3/O3 system. This work provides a new protocol for O3 activation and pollutant elimination through a novel bimetallic catalyst during water purification.

Underwater bubbling plasma assisted with persulfate activation for the synergistic degradation of tetracycline hydrochloride

The performance and mechanism of persulfate consisting of peroxymonosulfate (PMS) and peroxydisulfate (PDS) activation by underwater bubbling plasma (UBP) for the synergistic removal of tetracycline hydrochloride (TCH) were comparatively investigated. Both PMS and PDS addition significantly promoted the removal of TCH in UBP system, indicating persulfate exhibited highly synergistic effect with UBP. Furthermore, enhancing the persulfate dosage, peak voltage and pulse frequency, as well as reducing initial TCH concentration were favorable for the elimination of TCH. Compared with neutral condition, acidic and alkaline condition were advantageous to TCH removal. The presence of coexisting substances including Cl-, SO42- and humic acid (HA) had an adverse effect on TCH degradation, while Fe2+ could improve the removal of TCH. The degradation of ciprofloxacin and metronidazole proved the applicability for other antibiotics degradation of the reaction system. SO4-·, ·OH, ·O2-, hydrated electrons, O3 and H2O2 were the active substances responsible for TCH removal. The reduction of aqueous O3 concentration and enhancement of H2O2 concentration were observed after persulfate addition. UV-vis spectra and TOC analysis illustrated the addition of PMS or PDS facilitated the degradation and mineralization of TCH. 3D-EEMF spectra visually displayed the degradation process of TCH. Plausible degradation routes were deduced based on LC-MS and the toxicities of TCH and its intermediates were evaluated by Toxicity Estimation Software Tool.

New insights into Co3O4-carbon nanotube membrane for enhanced water purification: Regulated peroxymonosulfate activation mechanism via nanoconfinement

Co-based peroxymonosulfate (PMS) activation system with fascinating catalytic performance has become a promising technology for water purification, but it always suffers from insufficient mass transfer, less exposed active sites and toxic metal leaching. In this work, a carbon nanotube membrane confining Co3O4 inside (Co3O4-in-CNT) was prepared and was coupled with PMS activation (catalytic membrane process) for sulfamethoxazole (SMX) removal. Compared with counterpart with surface-loaded Co3O4 (Co3O4-out-CNT), the Co3O4-in-CNT catalytic membrane process exhibited enhanced SMX removal (99.5% vs. 89.1%) within residence time of 2.89 s, reduced Co leaching (20 vs. 147 μg L-1) and more interestingly, the nonradical-to-radical mechanism transformation (from 1O2 and electron transfer to SO4•- and •OH). These phenomena were ascribed to the nanoconfinement effect in CNT, which enhanced mass transfer (2.80 × 10-4 vs. 5.98 × 10-5 m s-1), accelerated Co3+/Co2+ cycling (73.4% vs. 65.0%) and showed higher adsorption energy for PMS (cleavage of O-O bond). Finally, based on the generated abundant reactive oxygen species (ROS), the seven degradation pathways of SMX were formed in system.

Persulfate-based remediation of organic-contaminated soil: Insight into the impacts of natural iron ions and humic acids with complexation/redox functionality

The use of persulfate (PDS) for in-situ chemical oxidation of organic contaminants in soils has garnered significant interest. However, the presence of naturally occurring iron-containing substances and humic acid (HA) in environmental compartments can potentially influence the effectiveness of soil remediation. Thus, this study aimed to investigate the role of key functional groups (adjacent phenolic hydroxyl (Ar-OH) and carboxyl groups (-COOH)) in HA that interact with iron. Modified HAs were used to confirm the significance of these moieties in iron interaction. Additionally, the mechanism by which specific functional groups affect Fe complexation and redox was explored through contaminant degradation experiments, pH-dependent investigations, HA by-products analysis, and theoretical calculations using six specific hydroxybenzoic acids as HA model compounds. The results showed a strong positive correlation between accessible Ar-OH and -COOH groups and Fe3+/Fe2+ redox. This was attributed to HA undergoing a conversion process to a semiquinone-containing radical form, followed by a quinone-containing intermediate, while Fe3+ acted as an electron shuttle between HA and PDS, with Fe3+ leaching facilitated by generated H+ ions. Although the stability of HA-Fe3+ complexes with -COOH as the primary binding sites was slightly higher at neutral/alkaline conditions compared to acidic conditions, the buffering properties of the soil and acidification of the PDS solution played a greater role in determining the Ar-OH groups as the primary binding site in most cases. Therefore, the availability of Ar-OH groups on HA created a trade-off between accelerated Fe3+/Fe2+ redox and quenching reactions. Appropriate HA and iron contents were found to favor PDS activation, while excessive HA could lead to intense competition for reactive oxygen species (ROS), inhibiting pollutant degradation in soil. The findings provide valuable insights into the interaction of HA and Fe-containing substances in persulfate oxidation, offering useful information for the development of in-situ remediation strategies for organic-contaminated soil.

Efficient Degradation of Ciprofloxacin in Water over Copper-Loaded Biochar Using an Enhanced Non-Radical Pathway

The development of an efficient catalyst with excellent performance using agricultural biomass waste as raw materials is highly desirable for practical water pollution control. Herein, nano-sized, metal-decorated biochar was successfully synthesized with in situ chemical deposition at room temperature. The optimized BC-Cu (1:4) composite exhibited excellent peroxymonosulfate (PMS) activation performance due to the enhanced non-radical pathway. The as-prepared BC-Cu (1:4) composite displays a superior 99.99% removal rate for ciprofloxacin degradation (initial concentration 20 mg·L-1) within 40 min. In addition, BC-Cu (1:4) has superior acid-base adaptability (3.98~11.95) and anti-anion interference ability. The trapping experiments and identification of reactive oxidative radicals confirmed the crucial role of enhanced singlet oxygen for ciprofloxacin degradation via a BC-Cu (1:4)/PMS system. This work provides a new idea for developing highly active, low-cost, non-radical catalysts for efficient antibiotic removal.

Engineered hydrochar from waste reed straw for peroxymonosulfate activation to degrade quinclorac and improve solanaceae plants growth

Hydrochar from agricultural wastes is regarded as a prospective and low-cost material to activate peroxymonosulfate (PMS) for degrading pollutants. Herein, a novel in-situ N-doped hydrochar composite (RHCM4) was synthesized using montmorillonite and waste reed straw rich in nitrogen as pyrolysis catalyst and carbon source, respectively. The fabricated RHCM4 possessed excellent PMS activation performance for decomposing quinclorac (QC), a refractory herbicide, with a high removal efficiency of 100.0% and mineralization efficiency of 75.1%. The quenching experiments and electron spin resonance (ESR) detection disclosed free radicals (•OH, •SO4-, and •O2-) and non-radicals (1O2) took part in the QC degradation process. Additionally, the catalytic mechanisms were analyzed in depth with the aid of various characterizations. Moreover, the QC degradation intermediates and pathways were clarified by density functional theory calculations and HPLC-MS. Importantly, phytotoxicity experiments showed that RHCM4/PMS could efficaciously mitigate the injury of QC to Solanaceae crops (pepper, tomato, and tobacco). These findings give a new idea for enhancing the catalytic activity of hydrochar from agricultural wastes and broaden its application in the field of agricultural environment.

Unraveling the single-atom Fe-N4 catalytic site selectivity generate singlet oxygen via activation of persulfate: Polarizing electric fields changes the electron transfer pathway

Single-atom catalysts have been proved to be an effective material for the removal of organic pollutants from water and wastewater, and yet, the relationship between their internal structures and their roles still remains elusive. In this work, a catalyst Fe (MIL)-SAC with single-atom Fe-N4 active site was prepared. Fe (MIL)-SAC/Peroxydisulfate (PDS) system was able to achieve complete degrade of the Sulfamethoxazole (SMX) with kobs at 0.466 min-1, which was faster than the Fenton system under the same conditions (kobs = 0.422 min-1) and 16 times faster than Fe (MIL) (kobs = 0.029 min-1). Density functional calculations reveal that the Fe-N4 structure will affect the electron transport path and lead to selective generation of 1O2 by triggering S-O breakage and O-O polarization in PDS. Furthermore, Fe (MIL)-SAC/PDS system exhibits strong resistance to common influencing factors and has good application prospects. This work provides a new approach for the selectively generation of 1O2 for the efficient treatment of organic pollutants in aqueous environment.

Acid-modified red mud biochar for the degradation of tetracycline: Synergistic effect of adsorption and nonradical activation

In this study, a novel acid-modified red mud biochar catalyst (MMBC) was synthesized by industrial waste red mud (RM) and peanut shell (PSL) to activate peroxodisulfate (PDS) for the degradation of TC. Meanwhile, MMBC exhibited remarkable adsorption capacity, reaching a 60% removal ratio of TC within 60 min (equilibrium adsorption capacity = 12 mg/g). After adding PDS, MMBC/PDS system achieved a 93.8% removal ratio of TC within 60 min. Quenching experiments and electron paramagnetic resonance (EPR) results showed that 1O2 played a dominant role in the degradation of TC and O2•- was the mainly precursor for the production of 1O2 in the MMBC/PDS system. X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR) analysis showed that the surface Fe(II), -OH and -COOH provided the active sites for the activation of PDS by MMBC. In addition, acid modification optimised the surface structure of the catalyst and enhanced the conversion of Fe (mainly Fe(III) to Fe(II)), thereby improving the adsorption and catalytic efficiency of MMBC. This study confirmed that modified red mud biochar is an efficient composite with both adsorption and catalysis, providing new ideas for the practical treatment of antibiotic wastewater and the resource utilization of red mud.

Biochar-Based Single-Atom Catalyst with Fe-N3O-C Configuration for Efficient Degradation of Organic Dyes by Peroxymonosulfate Activation

Iron single-atom catalysts (Fe SACs) hold great promise for peroxymonosulfate (PMS) activation and degradation of organic pollutants in wastewater. However, insights into crucial catalytic sites and activation mechanisms of biochar-based Fe SACs for PMS remain a challenge. Herein, cotton stalk-derived biochar-based Fe SACs (Fe SACs-BC) with an asymmetric Fe-N/O-C configuration were prepared, and their PMS activation and acid orange 7 (AO7) degradation mechanisms were investigated. The results showed that the removal efficiency of the Fe SACs-BC catalyst with Fe-N3O-C configuration for AO7 and other five investigated organic dyes reached 95-99% within 15 min. The EPR spectrums, quenching experiments, electrochemical analysis, masking experiments, XPS, and theoretical calculations indicated that degradations of organic dyes were dominated by singlet oxygen, which was generated by direct PMS conversion at the electron-deficient carbon and iron sites in the Fe-N3O-C configuration. The Fe SACs-BC/PMS exhibited high removal efficiency and strong tolerance in different water matrices with a wide pH range, various coexisting anions and interfering substances, showing great potential and applicability for efficient treatment of actual textile wastewaters.

ABTS as Both Activator and Electron Shuttle to Activate Persulfate for Diclofenac Degradation: Formation and Contributions of ABTS•+, SO4•-, and •OH

The activation of peroxydisulfate (PDS) by organic compounds has attracted increasing attention. However, some inherent drawbacks including quick activator decomposition and poor anti-interference capacity limited the application of organic compound-activated PDS. It was interestingly found that 2,2'-azino-bis (3-ethylbenzothiazoline-6-sulfonate) (ABTS) could act as both activator and electron shuttle for PDS activation to enhance diclofenac (DCF) degradation over a pH range of 2.0-11.0. Multiple reactive species of ABTS•+, •OH, and SO4•- were generated in the PDS/ABTS system, while only ABTS•+ and •OH directly contributed to DCF degradation. ABTS•+, generated via the reactions of ABTS with PDS, SO4•-, and •OH, was the dominant reactive species of DCF degradation. No significant decomposition of ABTS was observed in the PDS/ABTS system, and ABTS acted as both activator and electron shuttle. Four possible degradation pathways of DCF were proposed, and the toxicity of DCF decreased after treatment with the PDS/ABTS system. The PDS/ABTS system had good anti-interference capacity to common natural water constituents. Additionally, ABTS was encapsulated into cellulose to obtain ABTS@Ce beads, and the PDS/ABTS@Ce system possessed excellent performance on DCF degradation. This study proposes a new perspective to reconsider the mechanism of activating PDS with organic compounds and highlights the considerable contribution of organic radicals on contaminant removal.

Peroxymonosulfate-Based Electrochemical Advanced Oxidation: Complication by Oxygen Reduction Reaction

Peroxymonosulfate (PMS)-based electrochemical advanced oxidation processes (EAOPs) have received widespread attention in recent years, but the precise nature of PMS activation and its impact on the overall process performance remain poorly understood. This study presents the first demonstration of the critical role played by the oxygen reduction reaction in the effective utilization of PMS and the subsequent enhancement of overall pollutant remediation. We observed the concurrent generation of H2O2 via oxygen reduction during the cathodic PMS activation by a model nitrogen-doped carbon nanotube catalyst. A complex interplay between H2O2 generation and PMS activation, as well as a locally increased pH near the electrode due to the oxygen reduction reaction, resulted in a SO4•-/•OH-mixed oxidation environment that facilitated pollutant degradation. The findings of this study highlight a unique dependency between PMS-driven and H2O2-driven EAOPs and a new perspective on a previously unexplored route for further enhancing PMS-based treatment processes.

Cobalt-aluminum spinel supported on modified γ-alumina for peroxymonosulfate activation: Si-Al ratio of support to optimize performance and reusability

The development of cobalt-based supported catalysts with high PMS catalytic activity and stability by adjusting the composition of the support is highly desirable yet remains scarce. In the work, a series of catalysts (Co2AlO4/Al2O3-xSiO2) were prepared by impregnation and high-temperature calcination using Al2O3-xSiO2 with a low Si-Al ratio as the support. Measurement techniques such as XRD, XPS, UV-DRS, FTIR, BET, SEM and HRTEM were used to characterize textural and chemical properties (ratio of Co3+/Co2+, specific surface area, pore size, pore volume, etc.). The ratio of Co3+/Co2+ and pore volume of Co2AlO4/Al2O3-xSiO2 can be turned by controlling the ratio of Si to Al, which are closely related to the catalytic performance and reusability of the catalysts. The optimized catalyst (Co2AlO4/Al2O3-0.25SiO2) can completely degrade 10 mg/L p-nitrophenol (PNP) in 40 min in the pH range of 3-9 with excellent reusability. The effects of several reaction parameters (i.e., PMS dosage, Co2AlO4/Al2O3-0.25SiO2 dosage, reaction temperature, initial pH value, and inorganic ions) on PNP removal were comprehensively investigated. Sulfate radical (SO4•-) and singlet oxygen (1O2) are making a major contribution to the degradation of PNP. Moreover, a millimeter-scale catalyst (CoSiAl-0.25/Al2O3 pellet) was prepared by sol adsorption and high-temperature calcination method, which maintained high oxidation activity after treatment of 18 L wastewater (PNP of 10 mg/L) in a continuous flow process. The method is simple and easy to operate on a large scale, providing a new perspective on the design and preparation of cobalt-aluminum spinel catalysts for activated PMS.

A novel 3-dimensional graphene-based cobalt-manganese bimetallic layered double hydroxide:Formation mechanism and performance in photo-assisted permonosulfate-activated degradation of sulfamethoxazole in aqueous solution

Sulfamethoxazole (SMX) is a common antibiotic used mainly for bacterial treatment. In this study, a novel three-dimensional cobalt-manganese bimetallic layered double hydroxide graphene hydrogel (CoMn-LDHs/rGO) has been prepared for photo-assisted permonosulfate (PMS)-activated degradation of SMX in water. Compared with the CoMn-LDHs/rGO + PMS and CoMn-LDHs/rGO + Vis systems, the degradation effect of CoMn-LDHs/rGO + PMS + Vis system is the best, and the degradation effect of CoMn-LDHs/rGO system could reach more than 98% under the optimal conditions. After 10 cycles, the catalytic degradation performance of CoMn-LDHs/rGO system remained good, while effectively preventing the leaching of metal ions. Based on the synergistic effect of photocatalysis and PMS oxidation, electron spin resonance spectroscopy and quenching experiments showed that three active substances (•OH, •SO4- and O2•-) were involved in the degradation of SMX. Density functional theory and liquid chromatography-mass spectrometry (LC-MS) results further proposed the SMX degradation transformation calculation. As expected, the study of the reaction mechanism of 3D CoMn-LDHs/rGO assisted PMS activation under visible light provides an efficient and rapid method for the sustainable degradation of pollutants in water system.

Realism-based assessment of the efficacy of potassium peroxymonosulphate on Stenotrophomonas maltophilia biofilm control

The potential of pentapotassium bis(peroxymonosulphate) bis(sulphate) (OXONE) to control biofilms in drinking water distribution systems (DWDS) was evaluated and compared to chlorine disinfection. Mature biofilms of drinking water (DW)-isolated Stenotrophomonas maltophilia were formed using a simulated DWDS with a rotating cylinder reactor (RCR). After 30 min of exposure, OXONE at 10 × minimum bactericidal concentration (MBC) caused a significant 4 log reduction of biofilm culturability in comparison to the unexposed biofilms and a decrease in the number of non-damaged cells below the detection limit (4.8 log cells/cm2). The effects of free chlorine were restricted to approximately 1 log reduction in both biofilm culturability and non-damaged cells. OXONE in synthetic tap water (STW) at 25 ºC was more stable over 40 days than free chlorine in the same conditions. OXONE solution exhibited a disinfectant decrease of about 10% of the initial concentration during the first 9 days, and after this time the values remained stable. Whereas possible reaction of chlorine with inorganic and organic substances in STW contributed to free chlorine depletion of approximately 48% of the initial concentration. Electron paramagnetic resonance (EPR) spectroscopy studies confirmed the presence of singlet oxygen and other free radicals during S. maltophilia disinfection with OXONE. Overall, OXONE constitutes a relevant alternative to conventional DW disinfection for effective biofilm control in DWDS.

Dual Activation of Peroxymonosulfate Using MnFe2O4/g-C3N4 and Visible Light for the Efficient Degradation of Steroid Hormones: Performance, Mechanisms, and Environmental Impacts

Single activation of peroxymonosulfate (PMS) in a homogeneous system is sometimes insufficient for producing reactive oxygen species (ROS) for water treatment applications. In this work, manganese spinel ferrite and graphitic carbon nitride (MnFe2O4/g-C3N4; MnF) were successfully used as an activator for PMS under visible light irradiation to remove the four-most-detected-hormone-contaminated water under different environmental conditions. The incorporation of g-C3N4 in the nanocomposites led to material enhancements, including increased crystallinity, reduced particle agglomeration, amplified magnetism, improved recyclability, and increased active surface area, thereby facilitating the PMS activation and electron transfer processes. The dominant active radical species included singlet oxygen (1O2) and superoxide anions (O2•-), which were more susceptible to the estrogen molecular structure than testosterone due to the higher electron-rich moieties. The self-scavenging effect occurred at high PMS concentrations, whereas elevated constituent ion concentrations can be both inhibitors and promoters due to the generation of secondary radicals. The MnF/PMS/vis system degradation byproducts and possible pathways of 17β-estradiol and 17α-methyltestosterone were identified. The impact of hormone-treated water on Oryza sativa L. seed germination, shoot length, and root length was found to be lower than that of untreated water. However, the viability of both ELT3 and Sertoli TM4 cells was affected only at higher water compositions. Our results confirmed that MnF and visible light could be potential PMS activators due to their superior degradation performance and ability to produce safer treated water.

Peroxymonosulfate assisted pesticide breakdown: Unveiling the potential of a novel S-scheme ZnO@CoFe2O4 photo-catalyst, anchored on activated carbon

A ternary hetero-junction was prepared by anchoring ZnO@CoFe2O4 (ZCF) on activated carbon (AC) and employed as a UV-assisted peroxymonosulfate (PMS) activator to boost the degradation of diazinon (DZN) pesticide. The structure, morphology, and optical properties of the ZCFAC hetero-junction were characterized through a series of techniques. The highest degradation efficiency of DZN (100% in 90 min) was achieved by the PMS-mediated ZCFAC/UV system, superior to other single or binary catalytic systems due to the strong synergistic effect between ZCFAC, PMS, and UV. The operating reaction conditions, synergistic effects, and the possible pathways of DZN degradation were investigated and discussed. Optical analysis showed that the band-gap energy of the ZCFAC hetero-junction not only enhanced the absorption of UV light but also reduced the recombination of photo-induced electron/hole pairs. Both radical and non-radical species (HO•, SO4•-, O2•-, 1O2, and h+) took part in the photo-degradation of DZN, assessed by scavenging tests. It was found that AC as a carrier not only improved the catalytic activity of CF and ZnO nanoparticles and conferred high stability for the catalyst but also played a crucial role in accelerating the catalytic PMS activation mechanism. Moreover, the PMS-mediated ZCFAC/UV system showed good reusability, universality, and practical applicability potential. Overall, this work explored an efficient strategy for the best use of hetero-structure photo-catalysts towards PMS activation to achieve high performance in decontaminating organic compounds.

Facile synthesis of NaA zeolite supported Co2Fe1 for highly efficient degradation of Acid Orange 7 by activation of peroxymonosulfate

The development of heterogeneous Co-based catalysts with an effective combination mode of Co/Fe and supporter, a facile synthetic method, and a low treatment cost is an important environment challenge for azo dyes degradation by peroxymonosulfate (PMS) activation. In this study, NaA zeolite supported CoxFey with various molar ratio of Fe/Si and Co/Fe was synthesized by a facile hydrothermal process, and used to activate PMS for Acid Orange 7 (AO7) degradation. NaA zeolite supported Co2Fe1 with the Fe/Si molar ratio of 1:10 showed superior catalytic performance compared with other NaA zeolite supported CoxFey. In a system containing 0.6 g/L catalysts, 4 mM PMS, pH 5 and T = 30℃, 95.8% AO7 and 79.1% COD conversion could be achieved at 20 and 60 min, respectively, and the first order kinetic rate constant reached 0.14795 min-1. Moreover, NaA zeolite supported Co2Fe1/PMS system exhibited excellent catalytic effect in a wide pH range of 3-9. Temperature had an obvious effect on AO7 degradation, and the activation energy was 31.36 kJ/mol. HCO3- demonstrated an obvious depression on AO7 degradation, while Cl-, SO42- and H2PO4- had a relatively poor impact. Quenching experiments showed that both sulfate radicals ([Formula: see text]) and hydroxyl radicals (·OH) were generated in the PMS reaction system, and the [Formula: see text] was the dominant active radical. During 3 cycles experiments, an acceptable AO7 conversion ratio (91.8%) within 30 min arrived, suggesting the good stability of NaA zeolite supported Co2Fe1.