Adsorption modeling, thermodynamics, and DFT simulation of tetracycline onto mesoporous and high-surface-area NaOH-activated macroalgae carbon

Antimicrobial polymer-based zeolite imidazolate framework composite membranes for uranium extraction from wastewater and seawater

Extraction uranium (VI) (U(VI)) from wastewater and seawater is highly important for environmental protection and life safety, but it remains a great challenge. In this work, the growth of the zeolitic imidazolate framework-8 (ZIF-8) nanoparticles on the tannic acid (TA)-3-aminopropyltriethoxysilane (APTES) modified PVDF (TAP) membrane was designed to obtain an excellent U(VI) adsorbent. The zeolite imidazolate framework composite membrane (TAPP-ZIF-60) was prepared through polyethyleneimine (PEI) bridging strategy and temperature regulation strategy in solvothermal method. The coordination bond between PEI and ZIF-8 and the covalent bond between PEI and TAP are essential in forming stable composite membrane. TAPP-ZIF with different properties was synthesized through a temperature regulation process and the TAPP-ZIF prepared at 60 °C has the uniform morphology and good performance. The adsorption capacity of TAPP-ZIF-60 is 153.68 mg/g (C0 = 95.01 mg/L and pH = 8.0) and water permeability is 5459 L m-2 h-1 bar-1. After ten adsorption-desorption cycles, it is proved that TAPP-ZIF-60 has good repeatability and stability. In addition, the TAPP-ZIF-60 composites membrane has a good inhibitory effect on Staphylococcus aureus and Escherichia coli. X-ray photoelectron spectroscopy (XPS) and density functional theory (DFT) analysis reveal that the coordination between TAPP-ZIF-60 and uranyl ions is the primary factor contributing to the high adsorption capacity.

Polydopamine coating for enhanced electrostatic adsorption of methylene blue by multiwalled carbon nanotubes in alkaline environments

The removal of dye molecules in alkaline environments is an issue that should receive increased attention. In this study, the interaction mechanism between polydopamine-modified multiwalled carbon nanotubes (P-MWCNTs) and multiwalled carbon nanotubes (MWCNTs) with the cationic dye methylene blue (MB) in alkaline environments was explained in depth by adsorption, spectroscopy, and density functional theory (DFT). The mechanism of action and dominant forces between the adsorbent and adsorbate were analyzed graphically by introducing energy decomposition analysis (EDA) and an independent gradient model (IGM) into the DFT calculations. In addition, the force distribution was investigated through an isosurface. Moreover, batch adsorption studies were conducted to evaluate the performance of MWCNTs and P-MWCNTs for MB removal in alkaline environments. The maximum MB adsorption capacities of the MWCNTs and P-MWCNTs in solution were 113.3 mg‧g-1 and 230.4 mg‧g-1, respectively, at pH 9. The IGM and EDA showed that the better adsorption capacity of the P-MWCNTs originated from the enhancement of the electrostatic effect by the proton dissociation of polydopamine. Moreover, the adsorption of MB by MWCNTs and P-MWCNTs in alkaline environments was governed by dispersion and electrostatic effects, respectively. Through this study, it is hoped that progress will be made in the use of DFT to explore the mechanism of adsorbent-adsorbate interactions.

Zirconium and cerium dioxide fabricated activated carbon-based nanocomposites for enhanced adsorption and photocatalytic removal of methylene blue and tetracycline hydrochloride

Activated carbon (AC) is a porous, amorphous form of carbon known for its strong adsorption capacity, making it highly effective for use in wastewater treatment. In this investigation, AC-based nanocomposites (NCs) loaded with zirconium dioxide and cerium dioxide nanoparticles (ZrO2/CeO2 NPs) were successfully synthesized for the effective elimination of methylene blue (MB) and tetracycline hydrochloride (TCH). The AC-ZrO2/CeO2 NCs have a size of 231.83 nm, a zeta potential of -20.07 mV, and a PDI value of 0.160. The adsorption capacities of AC-ZrO2/CeO2 NCs for MB and TCH were proved in agreement with the Langmuir isotherm and pseudo 1st order kinetic model, respectively. The maximum adsorption capacities were determined to be 75.54 mg/g for MB and 26.75 mg/g for TCH. Notably, AC-ZrO2/CeO2 NCs exhibited superior photocatalytic degradation efficiency for MB and TCH under sunlight irradiation with removal efficiencies reaching up to 97.91% and 82.40% within 90 min, respectively. The t1/2 for the photo-degradation process of MB and TCH were 11.55 min and 44.37 min. Analysis of active species trapping confirmed the involvement of hole (h+), superoxide anion (•O2-), and hydroxyl radical (•OH) in the degradation mechanism. Furthermore, the residual solution post-contaminant removal exhibited minimal toxicity towards Artemia salina and NIH3T3 cells. Importantly, the NCs did not exhibit antibacterial activity against tested pathogens post-absorption/degradation of TCH. Thus, AC-ZrO2/CeO2 NCs could be a promising nanomaterial for wastewater treatment applications.

Dual COF functionalized magnetic MXene composite for enhancing magnetic solid phase extraction of thiophene compounds from oilfield produced waters prior to GC-MS/MS analysis

In this study, a novel COFTABT@COFTATp modified magnetic MXene composite (CoFe2O4 @Ti3C2 @COFTABT@COFTATp) was synthesized by Schiff base reaction and irre-versible enol-keto tautomerization, and employed to establish a sensitive monitoring method for six thiophene compounds in oilfield produced water samples based on magnetic solid-phase extraction (MSPE) prior to gas chromatography coupled with a triple quadruple mass spectrometer (GC-MS/MS). The designed magnetic materials exhibited unexpected enrichment ability to target thiophene compounds and achieved good extraction efficiencies ranging from 83 % to 98 %. The developed MSPE/GC-MS/MS method exhibited good linearity in the range of 0.001-100 μg L-1, and obtained lower limits of detection ranging from 0.39 to 1.9 ng L-1. The spiked recoveries of thiophene compounds obtained in three oilfield produced water samples were over the range of 96.26 %-99.54 % with relative standard deviations (RSDs) less than 3.7 %. Notably, benzothiophene, 4-methyldibenzothiophene and 4,6-dimethyldibenzothiophene were detected in three oilfield-produced water samples. Furthermore, the material still kept favorable stability after six recycling experiments. The adsorption kinetics, adsorption isotherms as well as adsorption thermodynamics of thiophene compounds were investigated in detail to provide insight into the mechanisms. Overall, the present work contributed a promising strategy for designing and synthesizing new functionalized materials for the enrichment and detection of typical pollutants in the environment.

Synthesis of Self-Assembled Mesoporous ZnO Microspheres Designed for Microwave-Assisted Photocatalytic Degradation of Tetracycline

Microwave-assisted photocatalysis offers a novel approach for degrading antibiotics, while the mechanism of enhancement of microwave-induced photocatalysis remains poorly understood. In this study, tetracycline (TC) was degraded using the method of microwave-assisted photocatalysis with a ZnO catalyst, which was synthesized by the combination of hydrothermal and calcination methods. The self-assembled mesoporous ZnO catalyst exhibited superior catalytic activity in degrading TC. It is found that the degradation efficiency of TC by the ZnO catalysts with microwave-assisted photocatalysis is 4.27 times higher than that of photocatalysis alone. Of particular significance, we found that the optical absorption range of ZnO increased and the band gap decreased when microwave was introduced into the photocatalytic system. Semi-in situ photochemical tests demonstrated that more photogenerated electron-hole pairs were detected under microwave, thus further improving the photocatalytic activity of ZnO. The separation efficiency and charge transfer efficiency of photogenerated electron-hole pairs also improved due to the increase of oxygen vacancies in the synergistic effect. Meanwhile, h+ and ·OH were the main active species in the degradation system. The mechanism of microwave-induced photocatalysis is illustrated, and an efficient way for degrading antibiotic is provided in this work.

Highly efficient and sensitive detection of tetracycline in environmental water: Insights into the synergistic mechanism of biomass-derived carbon dots and N-methyl pyrrolidone solvent

The tetracycline (TC) residue in water environment has caused serious public safety issue. Thus, efficient sensing of TC is highly desirable for environmental protection. Herein, biomass-derived nitrogen-doped carbon dots (N-CDs) synthesized from natural Ophiopogon japonicus f. nanus (O. japonicus) were used for TC detection. The unique solvent synergism efficiently enhanced detection sensitivity, and the detailed sensing mechanism was deeply investigated. The blue fluorescence of N-CDs was quenched by TC via static quenching and inner filter effect. Moreover, the enhancement of green fluorescence from deprotonated TC was firstly proposed and sufficiently verified. The solvent effect of N-methyl pyrrolidone (NMP) and the fluorescence resonance energy transfer (FRET) with N-CDs achieved an instantaneous enhancement of the green emission by 64-fold. Accordingly, a ratiometric fluorescence method was constructed for rapid and sensitive sensing of TC with a low detection limit of 6.3 nM within 60 s. The synergistic effect of N-CDs and solvent assistance significantly improved the sensitivity by 7-fold compared to that in water. Remarkably, the biomass-derived N-CDs displayed low cost, good solubility, and desired stability. The deep insights into the synergism with solvent can provide prospects for the utilization of biomass-based materials and broaden the development of advanced sensors with promising applications.

Development of a NiFe2O4 covalent organic framework based magnetic solid-phase extraction approach for specific capture of quinolones in animal innards prior to UHPLC-Q-Orbitrap HRMS detection

This study aimed to present a selective and effective method for analyzing quinolones (QNs) in food matrix. Herein, a NiFe2O4-based magnetic sodium disulfonate covalent organic framework (NiFe2O4/COF) was prepared using a simple solvent-free grinding method, and was adopted as a selective adsorbent for magnetic solid phase extraction of QNs. Coupled with UHPLC-Q-Orbitrap HRMS, an efficient method for simultaneous detection of 18 kinds of QNs was established. The method exhibited good linearity (0.01-100 ng g-1), high sensitivity (LODs ranging from 0.0011 to 0.0652 ng g-1) and precision (RSDs below 9.5%). Successful extraction of QNs from liver and kidney samples was achieved with satisfactory recoveries ranging from 82.2% to 108.4%. The abundant sulfonate functional groups on NiFe2O4/COF facilitated strong affinity to QNs through electrostatic and hydrogen bonding interactions. The proposed method provides a new idea for the extraction of contaminants with target selectivity.

Advanced biopolymer-based Ti/Si-terephthalate hybrid materials for sustainable and efficient adsorption of the tetracycline antibiotic

This study involves the synthesis of an organic-inorganic hybrid material consisting of Ti/Si-terephthalate (Ti-TPA-Si) in a 1:1:1 ratio using sol-gel method and its reaction with cellulose and chitosan (Ti-TPA-Si-C and Ti-TPA-Si-CS). Characterization techniques such as XRD, FTIR, SEM, EDS, XPS, BET, TGA, and DTA were used. The incorporation of biopolymers (cellulose and chitosan) into the Ti/Si-terephthalate structure improved the morphology and textural properties of the hybrid materials, leading to increased adsorption capacity and sustainability. Adsorption experiments reveal that Ti-TPA-Si, Ti-TPA-Si-C, and Ti-TPA-Si-CS hybrid materials exhibit a high affinity towards tetracycline, achieving remarkable adsorption efficiencies of 88.27, 89.60, and 88.98 %, respectively. Isotherm studies indicate that the adsorption process follows both Langmuir (R2 = 0.971, 0.990, and 0.994) and Dubinin-Radushkevich (R2 = 0.922, 0.965, and 0.949) isotherm models. According to the Langmuir model, the maximum adsorption capacity (qm) of Ti-TPA-Si, Ti-TPA-Si-C, and Ti-TPA-Si-CS adsorbents was found to be 24.10, 33.56, and 26.59 mg/g, respectively. Kinetic studies indicate that the adsorption process follows both pseudo-second-order (R2 = 0.998, 0.984, and 0.989) and intra-particle diffusion (R2 = 0.995, 0.994, and 0.988) models. Thermodynamic studies reveal that adsorption processes are spontaneous and endothermic in nature. Reusability studies demonstrate their potential for repeated use without significant loss in performance.

Green synthesis of manganese ferrite magnetic nanoparticle and its modification with metallic-organic frameworks for the tetracycline adsorption from aqueous solutions: A mathematical study of kinetics, isotherms, and thermodynamics

In the current investigation, MnFe2O4/ZIF-8 nanocomposite was generated as a magnetic nanoadsorber using the extract of Dracocephalum plant and characterized by XRD, FTIR, VSM, BET, FESEM, EDS-mapping, TEM, XPS, TPD-NH3, and TGA analyses. Also, to determine its efficiency in the adsorption process of tetracycline, the effect of pH (3-9), nanocomposite dose (0.025-2 g/L), initial pollutant concentration (5-100 mg/L), contact time (5-200 min), and temperature (5-50 °C) were studied. The results of the morphological properties of the magnetic nanocomposite confirmed the spherical shape of this nanoadsorber with an average size of 54 ± 31 nm. BET analysis showed that modification of MnFe2O4 material with ZIF-8 as a new nanoadsorber leads to excellent modification of SBET (143.8 m2/g) and VTotal (0.44 cm3/g). The highest removal efficiency of tetracycline in optimal conditions (pH = 7, contact time = 120 min, nanocomposite dose = 1.5 g/L, and temperature = 20 °C for a tetracycline concentration of 20 mg/L) was 90.11%. As the temperature increased, the removal efficiency increased from 40.46% to 95.06% during 120 min, which indicates that the adsorption reaction is endothermic. In addition, the data obtained from the isotherms of Langmuir (R2 = 0.958), Freundlich (R2 = 0.534), and Temkin (R2 = 0.747) showed that the tetracycline adsorption is monolayer and on the homogeneous surface of the synthesized magnetic nanoadsorber. The elimination process of tetracycline by nanoadsorber followed the pseudo-second order model (R2 = 0.998). Investigating the effect of interfering ions also confirmed the decrease in the adsorption efficiency. Also, the investigation of the reusability of the synthesized magnetic nanoadsorber in tetracycline adsorption indicates that after eight cycles, the efficiency decreases by %16.51. According to the results, the magnetic nanocomposite synthesized in this work can be a suitable and economical adsorber for the removal of tetracycline from aqueous environments.

A sustainable carbon aerogel from waste paper with exceptional performance for antibiotics removal from water

In this work, a sustainable 3D carbon aerogel (AO-WPC) is prepared from waste paper (WP), and used for efficient antibiotics removal from water. The AO-WPC aerogel shows good mechanical property and can recover after 100th of 30 % compression strain. The specific surface area of AO-WPC aerogel is up to 654.58 m2/g. More importantly, this aerogel reveals proper pore size distribution, including micro sized macropores between carbon fibers and intrinsic nano scale mesopores (11.86 nm), which is conducive to remove antibiotics from water. Taking tetracycline (Tc) as an example, the maximum adsorption capacity and adsorption rate of AO-WPC for Tc are as high as 384.6 mg/g and 0.510 g/(mg‧min), respectively, which exhibits significant advantages over most of the recent absorbents, and the adsorption toward Tc reveals good resistance to various environmental factors, including pH, various ions, and dissolved organic matter (DOM). Moreover, good thermal stability enables the AO-WPC aerogel to be regenerated through simple burning, and the adsorption capacity of Tc only decreases by 10.4 % after 10 cycles. Mechanism research shows that hydrogen bonding and π-π electron-donor-acceptor (EDA) interaction play the important role in the adsorption. The excellent mechanical property and adsorption performance imply good practical prospect of the AO-WPC aerogel.

Removal of tetracycline from the aquatic environment using activated carbon: A comparative study of adsorption performance based on the activator agents

This research focus endeavour to compare the remediation of tetracycline (TC) through activated carbon (AC), crafted utilizing two distinct chemical activators: zinc chloride (ACZ), and potassium hydroxide (ACK), using pine cone biowaste as an effective carbon precursor, followed by microwave-assisted activation. The impact of TC removal by ACZ and ACK adsorbents was thoroughly examined. The influence of pH, adsorbent mass, adsorption isotherms, kinetics, and inclusive thermodynamics were studied. Our results revealed that the interaction between TC and ACZ or ACK adsorbents aligned well with the model of pseudo-second-order kinetics, whilst the Langmuir model fitted the adsorption isotherm data of ACZ and ACK. The ACZ have a maximum adsorption capacity of 327.87 mg/g compared to that of the ACK (283.29 mg/g). Adsorption of TC was facilitated by the suitable pore volume, abundant microporous, and mesoporous structure of these adsorbents. The ACZ adsorbent is abundant in oxygen-containing functional groups, compared to ACK with minimized reactive sites, in bonding with the TC molecules through hydrogen bonding, for faster removal of TC. Our finding from this work further highlights that the synthesized ACZ from pine cones evidenced significant environmental potentials in the elimination of antibiotics from aqueous solution, to promote clean application perspectives.

Construction of functionalized In-based metal organic framework/BiOCl1-xIx Z-scheme heterojunction for efficient photocatalytic degradation of tetracycline: Performance and mechanism

The environmental implications of antibiotics have drawn widespread attention. Numerous monomer-based bismuth oxide halide catalysts have been extensively studied to remove tetracycline (TC) from aquatic environments. Integrating bismuth oxide halide composites with In-based metal organic framework (NH2-MIL-68(In)) might potentially serve as a novel strategy. By meticulously adjusting Cl and I within the composite bismuth halide oxide (B-x), a suite of purpose built heterojunctions (NMB-x) were synthesized, which were engineered to facilitate the efficient photodegradation of TC in simulated and actual aquatic environments. The incorporation of Z-scheme heterojunctions yielded a significant enhancement in photocatalytic responsiveness and charge carrier separation. Notably, NMB-0.3 demonstrated remarkable TC removal efficiency of 88.52 ± 3.05%, which is 3.74 times of B-0.3 within 90 min. The apparent quantum yield was also increased from 8.97% (B-0.3) to 19.68% (NMB-0.3). The removal of TC from natural water bodies was also assessed. Moreover, the photocatalyst concentration, assessed using response surface method, was found to show influential factors on TC removal. In addition, density functional theory (DFT) simulations were employed to identify vulnerable sites within TC. Intermediates and pathways in the photodegradation of TC have also been inferred. Furthermore, a comprehensive environmental toxicity assessment of representative intermediates demonstrated that these intermediates exhibited significantly reduced environmental toxicity compared to TC. This study provides a new approach to the design strategy of efficient and environmentally friendly MOF-based photocatalysts.

Unlocking the potential of Chinese herbal medicine residue-derived biochar as an efficient adsorbent for high-performance tetracycline removal

This study employed hydrothermal carbonization (HTC) in conjunction with ZnCl2 activation and pyrolysis to produce biochar from one traditional Chinese medicine astragali radix (AR) residue. The resultant biochar was evaluated as a sustainable adsorbent for tetracycline (TC) elimination from water. The adsorption performance of TC on two micropore-rich AR biochars, AR@ZnCl2 (1370 m2 g-1) and HAR@ZnCl2 (1896 m2 g-1), was comprehensively evaluated using adsorption isotherms, kinetics, and thermodynamics. By virtue of pore diffusion, π-π interaction, electrostatic attraction, and hydrogen bonding, the prepared AR biochar showed exceptional adsorption properties for TC. Notably, the maximum adsorption capacity (930.3 mg g-1) of TC on HAR@ZnCl2 can be achieved when the adsorbent dosage is 0.5 g L-1 and C0 is 500 mg L-1 at 323 K. The TC adsorption on HAR@ZnCl2 took place spontaneously. Furthermore, the impact of competitive ions behavior is insignificant when coexisting ion concentrations fall within the 10-100 mg L-1 range. Additionally, the produced biochar illustrated good economic benefits, with a payback of 701 $ t-1. More importantly, even after ten cycles, HAR@ZnCl2 still presented great TC removal efficiency (above 77%), suggesting a good application prosperity. In summary, the effectiveness and sustainability of AR biochar, a biowaste-derived product, were demonstrated in its ability to remove antibiotics from water, showing great potential in wastewater treatment application.

Endogenous iron-enriched biochar derived from steel mill wastewater sludge for tetracycline removal: Heavy metals stabilization, adsorption performance and mechanism

Steel mill wastewater sludge, as an iron-enriched solid waste, was expected to be converted into iron-enriched biochar with acceptable environmental risk by pyrolysis. The purpose of our study was to evaluate the chemical speciation transformation of heavy metals in biochar under various pyrolysis temperatures and its reutilization for tetracycline (TC) removal. The experimental data indicated that pyrolysis temperature was a key factor affecting the heavy metals speciation and bioavailability in biochar, and biochar with pyrolysis temperature at 450 °C was the most feasible for reutilization without potential risk. The endogenous iron-enriched biochar (FSB450) showed highly efficient adsorption towards TC, and its maximum adsorption capacity could reach 240.38 mg g-1, which should be attributed to its excellent mesoporous structure, abundant functional groups and endogenous iron cycling. The endogenous iron was converted to a stable iron oxide crystalline phase (Fe3O4 and MgFe2O4) by pyrolysis, which underwent a valence transition to form a coordination complex with TC by electron shuttling in the FSB450 matrix. The study provides a win-win approach for resource utilization of steel wastewater sludge and treatment of antibiotic contamination in wastewater.

Microbial synthesis of antimony sulfide to prepare catechol and hydroquinone electrochemical sensor by pyrolysis and carbonization

The application of antimony sulfide sensors, characterized by their exceptional stability and selectivity, is of emerging interest in detection research, and the integration of graphitized carbon materials is expected to further enhance their electrochemical performance. This study represents a pioneering effort in the synthesis of carbon-doped antimony sulfide materials through the pyrolysis of the mixture of microorganisms and their synthetic antimony sulfide. The prepared materials are subsequently applied to electrochemical sensors for monitoring the highly toxic compounds catechol (CC) and hydroquinone (HQ) in the environment. Via cyclic voltammetry (CV) and impedance testing, we concluded that the pyrolytic product at 700 °C (Sb-700) demonstrated the best electrochemical properties. Differential pulse voltammetry (DPV) revealed impressive separation when utilizing Sb-700/GCE for simultaneous detection of CC and HQ, exhibiting good linearity within the concentration range of 0.1-140 μM. The achieved sensitivities of 24.62 μA μM-1 cm-2 and 22.10 μA μM-1 cm-2 surpassed those of most CC and HQ electrochemical sensors. Meanwhile, the detection limits for CC and HQ were as low as 0.18 μM and 0.16 μM (S/N = 3), respectively. Additional tests confirmed the good selectivity, reproducibility, and long-term stability of Sb-700/GCE, which was effective in detecting CC and HQ in tap water and river water, with recovery rates of 100.7%-104.5% and 96.5%-101.4%, respectively. It provides a method that combines green microbial synthesis and simple pyrolysis for the preparation of electrode materials in CC and HQ electrochemical sensors, and also offers a new perspective for the application of microbial synthesized materials.

Urchin-like CO2-responsive magnetic microspheres for highly efficient organic dye removal

CO2-responsive materials have emerged as promising adsorbents for the remediation of refractory organic dyes-contaminated wastewater without the formation of byproducts or causing secondary pollution. However, realizing the simultaneous adsorption-separation or complete removal of both anionic and cationic dyes, as well as achieving deeper insights into their adsorption mechanism, still remains a challenge for most reported CO2-responsive materials. Herein, a novel type of urchin-like CO2-responsive Fe3O4 microspheres (U-Fe3O4 @P) has been successfully fabricated to enable ultrafast, selective, and reversible adsorption of anionic dyes by utilizing CO2 as a triggering gas. Meanwhile, the CO2-responsive U-Fe3O4 @P microspheres exhibit the capability to initiate Fenton degradation of non-adsorbable cationic dyes. Our findings reveal exceptionally rapid adsorption equilibrium, achieved within a mere 5 min, and an outstanding maximum adsorption capacity of 561.2 mg g-1 for anionic dye methyl orange upon CO2 stimulation. Moreover, 99.8% of cationic dye methylene blue can be effectively degraded through the Fenton reaction. Furthermore, the long-term unresolved interaction mechanism of organic dyes with CO2-responsive materials is deciphered through a comprehensive experimental and theoretical study by density functional theory. This work provides a novel paradigm and guidance for designing next-generation eco-friendly CO2-responsive materials for highly efficient purification of complex dye-contaminated wastewater in environmental engineering.

A review on sustainable management of biomass: physicochemical modification and its application for the removal of recalcitrant pollutants-challenges, opportunities, and future directions

Adsorption is one of the most efficient methods for remediating industrial recalcitrant wastewater due to its simple design and low investment cost. However, the conventional adsorbents used in adsorption have several limitations, including high cost, low removal rates, secondary waste generation, and low regeneration ability. Hence, the focus of the research has shifted to developing alternative low-cost green adsorbents from renewable resources such as biomass. In this regard, the recent progress in the modification of biomass-derived adsorbents, which are rich in cellulosic content, through a variety of techniques, including chemical, physical, and thermal processes, has been critically reviewed in this paper. In addition, the practical applications of raw and modified biomass-based adsorbents for the treatment of industrial wastewater are discussed extensively. In a nutshell, the adsorption mechanism, particularly for real wastewater, and the effects of various modifications on biomass-based adsorbents have yet to be thoroughly studied, despite the extensive research efforts devoted to their innovation. Therefore, this review provides insight into future research needed in wastewater treatment utilizing biomass-based adsorbents, as well as the possibility of commercializing biomass-based adsorbents into viable products.

Amorphous MnO2 Lamellae Encapsulated Covalent Triazine Polymer-Derived Multi-Heteroatoms-Doped Carbon for ORR/OER Bifunctional Electrocatalysis

The intelligent construction of non-noble metal materials that exhibit reversible oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) with bifunctional electrocatalytic performance is greatly coveted in the realm of zinc-air batteries (ZABs). Herein, a crafted structure-amorphous MnO2 lamellae encapsulated covalent triazine polymer-derived N, S, P co-doped carbon sphere (A-MnO2/NSPC) is designed using a self-doped pyrolysis coupled with an in situ encapsulation strategy. The customized A-MnO2/NSPC-2 demonstrates a superior bifunctional electrocatalytic performance, confirmed by a small ΔE index of 0.64 V for ORR/OER. Experimental investigations, along with density functional theory calculations validate that predesigned amorphous MnO2 surface defects and abundant heteroatom catalytic active sites collectively enhance the oxygen electrocatalytic performance. Impressively, the A-MnO2/NSPC-based rechargeable liquid ZABs show a large open-circuit potential of 1.54 V, an ultrahigh peak power density of 181 mW cm-2, an enormous capacity of 816 mAh g-1, and a remarkable stability for more than 1720 discharging/charging cycles. Additionally, the assembled flexible all-solid-state ZABs also demonstrate outstanding cycle stability, surpassing 140 discharging/charging cycles. Therefore, this highly operable synthetic strategy offers substantial understanding in the development of magnificent bifunctional electrocatalysts for various sustainable energy conversions and beyond.

Na/N Co-doped Seaweed Biochar Composite for Efficient Removal of Aqueous Pb(II) and Cu(II)

Pollution from harmful heavy metal ions such as Pb(II) and Cu(II) is causing serious environmental and health problems. In this study, Sodium and nitrogen co-doped porous carbon material (Na/NABc) was successfully prepared from seaweed, sodium hydroxide, and dicyandiamide. The experimental results showed that Na/NABc is an excellent adsorbent for the effective removal of Pb(II) and Cu(II) from water bodies. Specifically, 99.8% of Pb(II) and 64.6% Cu(II) (100 mg/L) were removed within 12 h using 10 mg Na/NABc(10%) at 25 °C. The adsorption of Pb(II) and Cu(II) in aqueous solution by Na/NABc(10%) was efficient and rapid in the first stage. The theoretical maximum removal capacities of Na/NABc for Pb(II) and Cu(II) were 959.6 and 299.1 mg/g, respectively. Pb(II) and Cu(II) ions were adsorbed quickly in the first 60 min, and the kinetics data were generally consistent with a pseudo-second-order model. Na/NABc(10%) had a large distribution coefficient for Pb(II) (8.38 L/mg) and Cu(II) (1.17 L/mg). The possible mechanisms were precipitation, Ion exchange, and surface complexation. The removal rate can reach about 70% after five cycles, and the release of sodium meets the standard. The results of this study demonstrate the potential applicability of Na/NABc(10%) for adsorption of heavy metals from aqueous solution.

Sulfuric acid-assisted ball milling for the preparation of Si-O-enriched straw biochar: removal efficiency of rhodamine B and adsorption mechanism

Traditional pyrolysis biochar has been widely employed to treat dye wastewater. However, there are some problems in the pyrolysis process, such as the generation of harmful gases and the low content of silico-oxygen functional groups to promote adsorption. Straw biochar (Ac-BCbm) was prepared by sulfuric acid co-ball milling method. The adsorption performance and adsorption mechanism of rhodamine B (RhB) under different preparation conditions and factors were investigated. The results showed that the adsorption rate of Ac-BCbm on RhB was up to 94.9%, which was 60.5% and 55.8% higher than that of ball-milling straw (STbm) and biochar prepared by pyrolysis (STBC600), respectively. The Ac-BCbm had better adaptability under different pH and common interfering ions for remove RhB. Characterization and DFT simulation analysis revealed that the sulfuric acid co-ball milling process promoted the formation of Si-OH and Si-O-CH3 oxygen-containing functional groups of Si component in straw, which enhanced the hydrogen bonding interactions and effectively improved the adsorption efficiency. This study investigated a new strategy for biochar preparation by sulfuric acid co-ball milling, which provides an additional development direction for the efficient resource utilization of straw.

Near-infrared light-activatable, analgesic nanocomposite delivery system for comprehensive therapy of diabetic wounds in rats

Impaired angiogenesis, bacterial infection, persistent severe pain, exacerbated inflammation, and oxidative stress injury are intractable problems in the treatment of chronic diabetic ulcer wounds. A strategy that effectively targets all these issues has proven challenging. Herein, an in-situ sprayable nanoparticle-gel composite comprising platinum clusters (Pt) loaded-mesoporous polydopamine (MPDA) nanoparticle and QX-314-loaded fibrin gel (Pt@MPDA/QX314@Fibrin) was developed for diabetic wound analgesia and therapy. The composite shows good local analgesic effect of QX-314 mediated by near-infrared light (NIR) activation of transient receptor potential vanilloid 1 (TRPV1) channel, as well as multifunctional therapeutic effects of rapid hemostasis, anti-inflammation, antioxidation, and antibacterial properties that benefit the fast-healing of diabetic wounds. Furthermore, it demonstrates that the composite, with good biodegradability and biosafety, significantly relieved wound pain by inhibiting the expression of c-Fos in the dorsal root ganglion and the activation of glial cells in the spinal cord dorsal horn. Consequently, our designed sprayable Pt@MPDA/QX314@Fibrin composite with good biocompatibility, NIR activation of TRPV1 channel-mediated QX-314 local wound analgesia and comprehensive treatments, is promising for chronic diabetic wound therapy.

Adsorption and reduction of Cr(VI) by N, S co-doped porous carbon from sewage sludge and low-rank coal: Combining experiments and theoretical calculations

Herein, a novel N, S co-doped porous carbon (S5C5-AC) for Cr(VI) removal was prepared by co-hydrothermal carbonization (HTC) of sewage sludge (SS) and low-rank coal (LC) combining with KOH modification. The results showed that S5C5-AC had excellent adsorption performance on Cr(VI), and lower pH value, higher initial concentration and longer contact time were beneficial for Cr(VI) adsorption. The adsorption kinetics and isotherms revealed that Cr(VI) adsorption by S5C5-AC was homogeneous and dominated by chemisorption. The adsorption isotherm showed that the maximum equilibrium adsorption capacity of S5C5-AC for Cr(VI) was 382.04 mg/g at 25 °C. Furthermore, the results showed that the main mechanisms for Cr(VI) removal were the pore filling, electrostatic interaction and reduction. Moreover, the electron transfer mechanism during the adsorption and reduction process was further explored at the molecular and electronic levels by density functional theory (DFT) and front orbital theory (FOT) simulations. The analysis of DFT and FOT indicated that the synergistic effect between S and N functional groups was exhibited during the Cr(VI) removal process. Considering the existence of synergistic effects between N and S functional groups during adsorption, the S and N content and form were modified collaboratively. Increasing the relative content of pyrrolic N may be the most effective pathway for improving removal performance. Besides that, S5C5-AC exhibited excellent adsorption capacity over a high coexisting ion concentration range and various actual water bodies and regeneration performance, which indicated that S5C5-AC had promising potential for the remediation of wastewater in industrial applications.

Efficient Adsorbent Derived from Phytolith-Rich Ore for Removal of Tetracycline in Wastewater

In recent decades, the tetracycline (TC) concentration in aquatic ecosystems has gradually increased, leading to water pollution problems. Various mineral adsorbents for the removal of tetracyclines have garnered considerable attention. However, efficient adsorbents suitable for use in a wide pH range environment have rarely been reported. Herein, a phytolith-rich adsorbent (PRADS) was prepared by a simple one-step alkali-activated pyrolysis treatment using phytolith as a raw material for effectively removing TC. PRADS, benefiting from its porous structure, which consists of acid- and alkali-resistant, fast-adsorbing macroporous silica and mesoporous carbon, is highly desirable for efficient TC removal from wastewater. The results indicate that PRADS exhibited excellent adsorption performance and stability for TC over a wide pH range of 2.0-12.0 under the coexistence of competing ions, which could be attributed to the fact that PRADS has a porous structure and contains abundant oxygen-containing functional groups and a large number of bonding sites. The adsorption mechanisms of PRADS for TC were mainly attributed to pore filling, hydrogen bonding, π-π electron-donor-acceptor, and electrostatic interactions. This work could offer a novel preparation strategy for the effective adsorption of pollutants by new functionalized phytolith adsorbents.

Constructing mesoporous biochar derived from waste carton: Improving multi-site adsorption of dye wastewater and investigating mechanism

The development of cost-efficient biochar adsorbent with a simple preparation method is essential to constructing efficient wastewater treatment system. Here, a low-cost waste carton biochar (WCB) prepared by a simple two-step carbonization was applied in efficiently removing Rhodamine B (RhB) in aqueous environment. The maximum ability of WCB for RhB adsorption was 222 mg/g, 6 and 10 times higher than both of rice straw biochar (RSB) and broadbean shell biochar (BSB), respectively. It was mainly ascribed to the mesopore structure (3.0-20.4 nm) of WCB possessing more spatial sites compared to RSB (2.2 nm) and BSB (2.4 nm) for RhB (1.4 nm✕1.1 nm✕0.6 nm) adsorption. Furthermore, external mass transfer (EMT) controlled mass transfer resistance (MTR) of the RhB sorption process by WCB which was fitted with the Langmuir model well. Meanwhile, the adsorption process was dominated by physisorption through van der Waals forces and π-π interactions. A mixture of three dyes in river water was well removed by using WCB. This work provides a straightforward method of preparing mesoporous biochar derived from waste carton with high-adsorption capacity for dye wastewater treatment.

Precursor-oriented design of nano-alumina for efficient removal of antibiotics

Rapid and efficient removal of environmental antibiotics is vital to curb bacterial resistance. Through rational precursors-oriented design, we attain the best Al2O3 absorbent by 500 °C calcination of ammonium aluminium carbonate hydroxide (AACH) precursor from NH4HCO3 route (AACH-NH4HCO3-500) for fast and efficient removal of tetracycline (TC) and other antibiotics from environmental waters including high-salinity wastewater. AACH-NH4HCO3-500 (0.25 g·L-1) can remove (69.92 ± 1.78)% of aqueous TC (0.025 g·L-1) within 5 min and (97.62 ± 2.75)% within 2 h, and the adsorption capacity is 444.4 mg·g-1, which is the highest qmax of TC for the 2 h-adsorptions among numerous adsorbents. AACH-NH4HCO3-500 has fine tolerance to the coexisting substances, and can be easily regenerated and reused, and has no harm even discarded. The relations among the synthetic methods, the structural features, and the adsorption functions of Al2O3 are disclosed through a systematic comparison of the commercial Al2O3 and different Al2O3 nanomaterials attained from three precursors produced by five different routes. The reasons behind the exceptional adsorption performance are discussed throughout. Our findings would facilitate the development of excellent adsorbents for removal of other pollutants.

Adsorption of tetracycline by polycationic straw: Density functional theory calculation for mechanism and machine learning prediction for tetracyclines' remediation

The abuse of antibiotics causes serious environmental pollution, whose removal has become a hot topic. The adsorption of tetracycline (TC) on a prepared polycationic straw (MMS) was investigated. The kinetic, thermodynamic and adsorption isotherm models showed that adsorption of TC by MMS was a spontaneous, monolayer reaction with coexistence of physical and chemical process. Density functional theory indicated that the adsorption of TC resulted from electrostatic interaction and hydrogen bonds, which proved the mechanism of TC by macromolecular biomass for the first time. The expected and empirical values of TC adsorption showed a high fit degree, through predication of machine learning, indicating the feasibility and avoiding lots of experiments. Further, the adsorption ability of MMS to other TCs was predicted, founding that the highest removal efficiency was doxycycline, which provides a novel strategy for removal of other pollution and reduce of economic and time cost in practical application.

Removal of methylene blue by acrylic polymer adsorbents loaded with magnetic iron manganese oxides: Synthesis, characterization, and adsorption mechanisms

Dyes pose significant risks for aquatic environments and biological health in general owing to their non-biodegradable nature, carcinogenicity, and toxicity. The effective treatment of dye wastewater has become an important research topic. In this study, acrylic polymers (AP) loaded with magnetic iron manganese oxides (MIMO) (AP/MIMO) were prepared and used for the first time for the adsorption of methylene blue (MB). Carbon in AP/MIMO exists predominantly in the C-H and C-C forms, with its content reaching 50.7%. Oxygen and nitrogen in AP/MIMO exist mainly in the -CO- and -N-C forms, with contents of up to 41.5% and 73.3%, respectively. MB removal by AP/MIMO was consistent with the pseudo-second-order kinetic model (R2 = 0.99), equilibrium was achieved within 20 min, and the highest MB capacity of 2611.23 mg g-1 was predicted by the Langmuir isotherm model (R2 = 0.91-0.94). AP/MIMO exhibited excellent MB adsorption performance in the pH range of 4-10, with a removal efficiency higher than 99.0% (MB = 100 mL 1000 mg L-1; AP/MIMO = 50 mg). Thermodynamic indicators, such as positive entropy (ΔS0; 98.30 J⋅mol-1⋅K-1), negative Gibbs free energy (ΔG0; -29.40, -28.50, and -27.50 KJ⋅mol-1), and positive enthalpy (ΔH0; 2.30 KJ⋅mol-1), demonstrated that MB removal by AP/MIMO was autonomous, favorable, and endothermic. In addition, the integration of experimental results and theoretical calculations verified that electrostatic interactions were the primary mechanism for MB adsorption at carboxyl sites on AP/MIMO. The total interaction energy between AP and MB was -310.43 kJ⋅mol-1, and the electrostatic effect had a decisive contribution to the MB adsorption, with a value of up to -341.06 kJ⋅mol-1. AP and MB were most likely bound by -COO and S atoms. Overall, AP/MIMO exhibits high adsorption capacity and shows potential as a high-performance magnetic polymer for MB removal.

Magnetic Persimmon Leaf Composite: Preparation and Application in Magnetic Solid-Phase Extraction of Pesticides in Water Samples

In recent years, the utilization of biomass materials for the removal and detection of water pollutants has garnered considerable attention. This study introduces, for the first time, the preparation of Fe3O4/persimmon leaf magnetic biomass composites. The magnetic composites were employed in a magnetic solid-phase extraction method, coupled with gas chromatography-electron capture detection (GC-ECD), for the analysis of four pesticides (trifluralin, triadimefon, permethrin, and fenvalerate) in environmental water samples. The innovative magnetic persimmon leaf composites were synthesized by in situ generation of Fe3O4 nanoparticles through coprecipitation and loaded onto persimmon leaves. These composites exhibit superparamagnetism with a saturation magnetization of 12.8 emu g-1, facilitating rapid phase separation using a magnetic field and reducing the extraction time to 10 min. Desorption can be achieved within 30 s by aspirating 20 times, eliminating the need for time-consuming and labor-intensive experimental steps like filtration and centrifugation. The specific surface area of the magnetic composite adsorbent increased from 1.3279 m2 g-1 for the original persimmon leaf to 5.4688 m2 g-1. The abundant hydroxyl and carboxyl groups on the composites provide ample adsorption sites, resulting in adsorption capacities ranging from 55.056 mg g-1 to 73.095 mg g-1 for the studied pesticides. The composites exhibited extraction recoveries ranging from 80% to 90% for the studied pesticides. Compared to certain previously reported MSPE methods, this approach achieves equivalent or higher extraction recoveries in a shorter operation time, demonstrating enhanced efficiency and convenience. Good linearity of the target analytes was obtained within the range of 0.75-1500 μg L-1, with a determination of coefficient (R2) greater than 0.999. These findings contribute to the use of magnetic persimmon leaf biomass materials as effective and environmentally friendly adsorbents for pollutant determination in water samples.

Biochar assisted cultivation of Chlorella protothecoides for adsorption of tetracycline and electrochemical study on self-cultured Chlorella protothecoides

Microalgae present a viable mechanism for purifying aquatic environments through the absorption of organic pollutants. In this paper, Chlorella protothecoides was cultured in a tetracycline environment, and biochar was added during the cultivation process. Compared with conventionally cultured Chlorella protothecoides, the addition of biochar for cultivation under a tetracycline environment increased the biomass of Chlorella protothecoides by 13.26 %. Moreover, the adsorption of tetracycline by biochar alone was not complete, but when mixed with Chlorella protothecoides, tetracycline was completely removed, which proved the biosorption of Chlorella protothecoides for low concentrations of tetracycline. Finally, the cultured Chlorella protothecoides was used further to prepare electrode materials, and it was found that the specific capacitance of the material reached 233.15F/g at a current density of 1 A/g. In this study, the use of biochar and Chlorella protothecoides to jointly adsorb tetracycline is of great significance for environmental protection and microalgae cultivation.

Exploring synergistic effects in physical-chemical activation of Acorus calamus for water treatment solutions

The research proposed a novel method of obtaining sorption material from readily available Acorus calamus biomass through a combination of physical and chemical activation processes. The material with the highest specific surface area (1652 m2 g-1) was obtained by physical activation with CO2, followed by chemical activation with KOH. Reversing the order of activation methods resulted in a lower specific surface area (1014 m2 g-1) of the carbon sample. Chemical activation produced activated carbon with a surface area of 1066 m2 g-1-, while physical activation produced 390 m2 g-1. This confirms the synergistic effect of combining the two activation methods for biocarbon. It was observed that physical activation with CO2 generates a diverse range of pores, including meso- and macropores, while chemical activation induces the formation of micropores. In contrast, reversing the order of these processes leads to the degradation of the porous structure. The application of physical-chemical activation with synergistic effects represents a significant advancement in producing high-quality activated biocarbon for various applications, such as wastewater treatment and energy storage. The combination of the two activation methods resulted in a synergistic effect, leading to the production of carbon material of higher quality. Additionally, the diversified pore sizes will enable the sorption of various pollutants in the aquatic environment and air pollutants, where gas particles are much smaller.

The adsorption of biogenetic odorants onto activated carbon: Adsorption characteristics and impacts of algal organic matter

Powdered activated carbon (PAC) adsorption is regarded as an efficient method for removing odorants from drinking water. However, in eutrophic aquatic environments, the presence of algal organic matter (AOM) produced by cyanobacteria considerably impedes the adsorption of odorous compounds by activated carbon. This study focused on investigating the adsorption characteristics of three representative odorants: 2-methylisoborneol (2-MIB), β-cyclocitral (β-cyclo), and butyl sulfide (BS) by PAC and the effects of AOM on the PAC adsorption of odorants. The removal of the three odorants reached 83.5-97.5% at a PAC dosage of 10 mg/L after 12 h of exposure in a competition-free scenario. The adsorption kinetics demonstrated higher conformity (R2 > 0.9) with the pseudo-second-order model, whereas the adsorption capacity exhibited stronger conformity (R2 > 0.9) with the Freundlich model. The presence of AOM resulted in varying levels of competition for PAC for the adsorption of the three odorants. As the concentration of AOM increased from 0 to 5 mg C/L, the removal of 2-MIB was the most affected (from 83.5% to 10.0%), followed by β-cyclo (from 86.6% to 55.0%), and BS (from 97.5% to 92.0%). The competitive adsorption of AOM at the molecular level was studied using density functional theory (DFT). The DFT results suggested that odorants with higher and more uniformly distributed electrostatic potentials exhibited a heightened affinity for PAC adsorption and a diminished susceptibility to disruption caused by AOM. This study provides valuable insights into the mitigation of odorous compounds during drinking water purification.

Production of activated carbon from date palm stones by hydrothermal carbonization and microwave assisted KOH/NaOH mixture activation for dye adsorption

Date palm stones are regarded as possible alternatives to activated carbon (AC) precursors with high potential for various environmental applications. In this research study, date palm stones derived activated carbon (DPSAC) was used as adsorbent for removing toxic remazol brilliant blue R (RBBR). The synthesis of DPSAC involved a chemical treatment using KOH and NaOH (1:1). Characterization of DPSAC revealed that it exhibited a BET surface area of 715.30 m2/g, Langmuir surface area of 1061.93 m2/g, total pore volume of 0.39 cm3/g, and average pore diameter of 2.15 nm. Adsorption uptake of RBBR increased (from 24.54 to 248.54 mg/g), whereas the removal percentage decreased (from 98.16 to 82.85%) when the initial RBBR concentration increased (from 25 to 300 mg/L). The adsorption process performed best under acidic conditions (pH 3), with an RBBR uptake of 98.33 mg/g. Because of the high R2 values (0.9906 and 0.9779) and low average errors (6.24 and 13.95%), this adsorption process followed the Freundlich isotherm and pseudo-first-order (PFO) models, respectively. The Langmuir adsorption capacity (Qm) was 319.63 mg/g. Thermodynamic parameters were - 11.34 kJ/mol for ∆H° (exothermic in nature), 0.05 kJ/mol K for ∆S° (increasing randomness level at solid-liquid interface), - 27.37 kJ/mol for ∆G° (spontaneous), and 6.84 kJ/mol for Ea (controlled by physisorption).

Response surface methodology for optimizing methylene blue dye removal by mesoporous activated carbon derived from renewable woody Bambusoideae waste

In this study, the focus was on utilizing tropical plant biomass waste, specifically bamboo (BB), as a sustainable precursor for the production of activated carbon (BBAC) via pyrolysis-induced K2CO3 activation. The potential application of BBAC as an effective adsorbent for the removal of methylene blue (MB) dye from aqueous solutions was investigated. Response surface methodology (RSM) was employed to evaluate key adsorption characteristics, which included BBAC dosage (A: 0.02-0.08 g/L), pH (B: 4-10), and time (C: 2-8 min). The adsorption isotherm analysis revealed that the adsorption of MB followed the Freundlich model. Moreover, the kinetic data were well-described by the pseudo-second-order model, suggesting the role of a chemisorption process. The BBAC demonstrated a notable MB adsorption capacity of 195.8 mg/g, highlighting its effectiveness as an adsorbent. Multiple mechanisms were identified as controlling factors in MB adsorption by BBAC, including electrostatic forces, π-π stacking, and H-bonding interactions. The findings of this study indicate that BBAC derived from bamboo has the potential to be a promising adsorbent for the treatment of wastewater containing organic dyes. The employment of sustainable precursors like bamboo for activated carbon production contributes to environmentally friendly waste management practices and offers a solution for the remediation of dye-contaminated wastewater.

Multi-stage adsorption of methyl orange on the nitrogen-rich biomass-derived carbon adsorbent: DFT and MD evaluation

Dyes that are released into the environment may have negative effects on living organisms. To address this issue, a biomass-derived carbon adsorbent made from Enteromorpha was tested for its ability to remove methyl orange (MO) from wastewater. The adsorbent was found to be effective in removing MO, with a 1:4 impregnation ratio producing an adsorbent that could remove 96.34% of MO from a 200 mg/L solution using only 0.1 g of adsorbent. At higher concentrations, the adsorption capacity increased up to 269.58 mg/g. Through molecular dynamics simulations, it was discovered that after mono-layer adsorption reached saturation, the remaining MO molecules in solution formed hydrogen bonds with the adsorbed MO, which led to further aggregation on the adsorbent surface and increased adsorption capacity. Additionally, theoretical investigations revealed that the adsorption energy of anionic dyes increased with Nitrogen-doped carbon materials, with the pyrrolic-N site having the highest adsorption energy for MO. The carbon material derived from Enteromorpha showed promise in treating wastewater containing anionic dyes, thanks to its high adsorption capacity and strong electrostatic interaction with the sulfonic acid groups of MO.

Intensive adsorption of tetracycline by cobalt oxide quantum dots-loaded mineral carbon

Spent bleaching earth (SBE), a waste by-product produced from the bleaching step of edible oil by montmorillonite clays (bleaching earth), causes serious public health and environmental problems. Accordingly, in this study, SBE was pyrolyzed to yield mineral carbon materials (SBE@C) and cobalt oxide (Co3O4) was loaded to improve the active site of those materials. Due to the carrier function of SBE@C, ultra-fine Co3O4 quantum dots (QDs) (2-6 nm) were homogeneously and robustly immobilized onto SBE@C. The obtained adsorbent exhibited high regeneration performance and an outstanding adsorption capacity (253.36 mg/g). It can be attributed to the surface complexation of cobalt with TC being the dominant process contributing to adsorption behavior. Further, Co3O4 QDs-SBE@C still maintained adequate sorption capacity at a broad range of pH values and in the presence of co-occurring ions. These results suggested the significant application potential of SBE and demonstrated the efficiency of using Co3O4 QDs-SBE@C for wastewater remediation.

Optimization and mechanistic approach for removal of crystal violet and methylene blue dyes via activated carbon from pyrolyzed-ZnCl2 bamboo waste

In this study, bamboo waste (BW) was subjected to pyrolysis-assisted ZnCl2 activation to produce mesoporous activated carbon (BW-AC), which was then evaluated for its ability to remove cationic dyes, specifically methylene blue (MB) and crystal violet (CV), from aqueous environments. The properties of BW-AC were characterized using various techniques, including potentiometric-based point of zero charge (pHpzc), scanning electron microscopy with energy dispersive X-rays (SEM-EDX), X-ray diffraction (XRD), gas adsorption with Brunauer-Emmett-Teller (BET) analysis, infrared (IR) spectroscopy. To optimize the adsorption characteristics (BW-AC dosage, pH, and contact time) of PBW, a Box-Behnken design (BBD) was employed. The BW-AC dose of 0.05 g, solution pH of 10, and time of 8 min are identified as optimal operational conditions for achieving maximum CV (89.8%) and MB (96.3%) adsorption according to the BBD model. The dye removal kinetics for CV and MB are described by the pseudo-second-order model. The dye adsorption isotherms revealed that adsorption of CV and MB onto BW-AC follow the Freundlich model. The maximum dye adsorption capacities (qmax) of BW-AC for CV (530 mg/g) and MB (520 mg/g) are favorable, along with the thermodynamics of the adsorption process, which is characterized as endothermic and spontaneous. The adsorption mechanism of CV and MB dyes by BW-AC was attributed to multiple contributions: hydrogen bonding, electrostatic forces, π-π attraction, and pore filling. The findings of this study highlight the potential of BW-AC as an effective adsorbent in wastewater treatment applications, contributing to the overall goal of mitigating the environmental impact of cationic dyes and ensuring the quality of water resources.

Adsorptive removal of malachite green dye from aqueous solution using Rumex abyssinicus derived activated carbon

The potential for malachite green dye saturated effluent to severely affect the environment and human health has prompted the search for effective treatment technologies. Thus, this study was conducted with the goal of developing activated carbon from Rumex abyssinicus for the adsorptive removal of malachite green dye from an aqueous solution. Unit operations such as drying, size reduction, impregnation with H3PO4, and thermal activation were used during the preparation of the activated carbon. An experiment was designed considering four main variables at their respective three levels: initial dye concentration (50, 100, and 150 mg/L), pH (3, 6, and 9), contact period (20, 40, and 60 min), and adsorbent dosage (0.05, 0.01, and 0.15 g/100 mL). Optimization of the batch adsorption process was carried out using the Response Surface methodology's Box Behnken approach. The characterization of the activated carbon was described by SEM for surface morphology with cracks and highly porous morphology, FTIR for multi-functional groups O-H at 3506.74 cm-1 and 3290.70 cm-1, carbonyl group stretching from aldehyde and ketone (1900-1700 cm-1), stretching motion of aromatic ring C=C (1543.12 cm-1), stretching motion of -C-H (1500-1200 cm-1), vibrational and stretching motion of -OH (1250.79 cm-1), and vibrational motion of C-O-C (1049.32 cm-1), pHpzc of 5.1, BET for the specific surface area of 962.3 m2/g, and XRD for the presence of amorphous structure. The maximum and minimum dye removal efficiencies of 99.9% and 62.4% were observed at their respective experimental conditions of (100 mg/L, 0.10 mg/100 mL, pH 6, and 40 min) and (100 mg/L, 0.15 mg/100 mL, pH 3, and 20 min), respectively. Langmuir, Freundlich, Toth, and Koble-Corrigan models were used to evaluate the experimental data, in which Koble-Corrigan model was found to be the best fit with the highest value of R2 0.998. In addition to this, the kinetic studies were undertaken using pseudo-first-order, pseudo-second-order, intraparticle diffusion, and Boyd models, and as a result, the pseudo-second-order model proved to have a better fit among the kinetic models. The kinetics and isotherm analysis revealed that the nature of the adsorption to be homogenous and monolayer surfaces driven by chemosorption. Furthermore, the thermodynamics study revealed the nature of adsorption to be feasible, spontaneous, and endothermic. On the other hand, the reusability study depicted the fact that the adsorbent can be utilized for five cycles with a negligible drop in the removal efficiencies from 99.9 to 95.2%. Finally, the low-cost, environmentally benign, and high adsorption capacity of the adsorbent material derived from Rumex abyssinicus stem could be used to treat industrial effluents.

Removal of tetracycline in aqueous solution by iron-loaded biochar derived from polymeric ferric sulfate and bagasse

In this study, the tetracycline (TC) removal performance of iron-loaded biochar (BPFSB) derived from sugarcane bagasse and polymerized iron sulfate was investigated, and the mechanism of TC removal was also explored by study of isotherms, kinetics and thermodynamics and characterization of fresh and used BPFSB (XRD, FTIR, SEM and XPS). The results showed that under optimized conditions (initial pH 2; BPFSB dosage 0.8 g·L-1; TC initial concentration 100 mg·L-1; Contact time 24 h; temperature 298 K), the removal efficiency of TC was as high as 99.03%. The isothermal removal of TC followed well the Langmuir, Freundlich, and Temkin models, indicating that multilayer surface chemisorption dominated the TC removal. The maximum removal capacity of TC by BPFSB at different temperatures was 185.5 mg·g-1 (298 K), 192.7 mg·g-1 (308 K), and 230.9 mg·g-1 (318 K), respectively. The pseudo-second-kinetic model described the TC removal better, while its rate-controlling step was a combination of liquid film diffusion, intraparticle diffusion, and chemical reaction. Meanwhile, TC removal was also a spontaneous and endothermic process, during which the randomness and disorder between the solid-liquid interface was increased. According to the characterization of BPFSBs before and after TC removal, H-bonding and complexation were the major interactions for TC surface adsorption. Furthermore, BPFSB was efficiently regenerated by NaOH. In summary, BPFSB had the potential for practical application in TC removal.

Functionally-designed floatable amino-modified ZnLa layered double hydroxides/cellulose acetate beads for tetracycline removal: Performance and mechanism

The over-reliance on tetracycline antibiotics (TC) in the animal husbandry and medical field has seriously affected the safety of the ecological environment. Therefore, how to effectively treat tetracycline wastewater has always been a long-term global challenge. Here, we developed a novel polyethyleneimine (PEI)/Zn-La layered double hydroxides (LDH)/cellulose acetate (CA) beads with cellular interconnected channels to strengthen the TC removal. The results of the exploration on its adsorption properties illustrated that the adsorption process exhibited a favorable correlation with the Langmuir model and the pseudo-second-order kinetic model, namely monolayer chemisorption. Among the many candidates, the maximum adsorption capacity of TC by 10 %PEI-0.8LDH/CA beads was 316.76 mg/g. Apart from that, the effects of pH, interfering species, actual water matrix and recycling on the adsorption of TC by PEI-LDH/CA beads were also analyzed to verify their superior removal capability. The potential for industrial-scale applications was expanded through fixed-bed column experiments. The proven adsorption mechanisms mainly included electrostatic interaction, complexation, hydrogen bonding, n-π EDA effect and cation-π interaction. The self-floating high-performance PEI-LDH/CA beads exploited in this work provided fundamental support for the practical application of antibiotic-based wastewater treatment.

Sorption of organic contaminants by biochars with multiple porous structures: Experiments and molecular dynamics simulations mediated by three-dimensional models

Interactions between organic pollutants and carbon-based particles are critical for understanding and predicting the fate of organic contaminants in the environment. However, traditional modeling concepts did not consider three-dimensional (3-D) structures of carbon-based materials. This prevents a deep understanding of the sequestration of organic pollutants. Therefore, this study revealed interactions between organics and biochars by combining experimental measurements and molecular dynamics simulations. Biochars displayed the best and worst sorption performances for naphthalene (NAP) and benzoic acid (BA), respectively, among the five adsorbates. The kinetic model fitting suggested that biochar pores played a vital role during sorption and led to the fast and slow sorption of organics on the biochar surface and in pores, respectively. Active sites on the biochar surface predominantly sorbed organics. Organics were only sorbed in pores when the surface's active sites were fully occupied. These results can guide the development of efficient organic pollution control strategies to protect human health and improve ecological security.

Porous biochar derived from walnut shell as an efficient adsorbent for tetracycline removal

In this study, a high-performance porous adsorbent was prepared from biochar through a simple one-step alkali-activated pyrolysis treatment of walnut shells, and it was effective in removing tetracycline (TC). The specific surface area (SSA) of potassium hydroxide-pretreated walnut shell-derived biochar pyrolyzed at 900°C (KWS900) increased remarkably compared to that of the pristine walnut shell and reached 1713.87±37.05 m²·g^-1. The maximum adsorption capacity of KWS900 toward TC was 607.00±31.87 mg·g^-1. The pseudo-second-order kinetic and Langmuir isotherm models were well suited to describe the TC adsorption process onto KWS900. The KWS900 exhibited high stability and reusability for TC adsorption in the presence of co-existing anions or cations over a wide pH range of 1.0-11.0. Further investigations demonstrated that the proposed adsorption mechanism involved pore filling, hydrogen bonding, π-π stacking, and electrostatic interaction. These findings provide a valuable reference for developing biochar-based adsorbents for pollutant removal.

Facile synthesis of chlorella-derived autogenous N-doped porous biochar for adsorption on tetracycline

In this study, an autogenous N-doped biochar derived from Chlorella (CVAC) was prepared with NaOH as activator at 800 °C. The surface structural properties of CVAC and the adsorption performance of CVAC on tetracycline (TC) under different adsorption variables were analyzed and investigated using different characterization methods. The results showed that the specific surface area of CVAC was 491.16 m² g^-1 and the adsorption process was in accordance with Freundlich model and pseudo-second-order kinetic model. The maximum adsorption capacity of TC was 310.696 mg g^-1 at pH 9 and 50 °C, and it was mainly physical adsorption. Furthermore, the cyclic adsorption-desorption behavior of CVAC using ethanol as eluent was evaluated and the feasibility of its long-term application was explored. CVAC also showed good cyclic performance. The variation of ΔG° and ΔH° confirmed that the adsorption of TC by CVAC was a spontaneous heat absorption process.

Benchmarking First-Principles Reaction Equilibrium Composition Prediction

The availability of thermochemical properties allows for the prediction of the equilibrium compositions of chemical reactions. The accurate prediction of these can be crucial for the design of new chemical synthesis routes. However, for new processes, these data are generally not completely available. A solution is the use of thermochemistry calculated from first-principles methods such as Density Functional Theory (DFT). Before this can be used reliably, it needs to be systematically benchmarked. Although various studies have examined the accuracy of DFT from an energetic point of view, few studies have considered its accuracy in predicting the temperature-dependent equilibrium composition. In this work, we collected 117 molecules for which experimental thermochemical data were available. From these, we constructed 2648 reactions. These experimentally constructed reactions were then benchmarked against DFT for 6 exchange-correlation functionals and 3 quality of basis sets. We show that, in reactions that do not show temperature dependence in the equilibrium composition below 1000 K, over 90% are predicted correctly. Temperature-dependent equilibrium compositions typically demonstrate correct qualitative behavior. Lastly, we show that the errors are equally caused by errors in the vibrational spectrum and the DFT electronic ground state energy.

High capacity adsorption of oxytetracycline by lignin-based carbon with mesoporous structure: Adsorption behavior and mechanism

In this study, an adsorbent with mesoporous structure and PO/PO bonds is prepared by hydrothermal and phosphoric acid activation from industrial alkali lignin for the adsorption of oxytetracycline (OTC). The adsorption capacity is 598 mg/g, which is three times higher than that of the adsorbent with microporous structure. The rich mesoporous structure of the adsorbent provides adsorption channels and filling sites, and π-π attraction, cation-π interaction, hydrogen bonds, and electrostatic attraction provide adsorption forces at the adsorption sites. The removal rate of OTC exceeds 98 % over a wide range of pH values (3-10). It has high selectivity for competing cations in water, with higher than 86.7 % removal rate of OTC from medical wastewater. After 7 consecutive adsorption-desorption cycles, the removal rate of OTC remains as high as 91 %. This efficient removal rate and excellent reusability indicate the strong potential of the adsorbent for industrial applications. This study prepares a highly efficient, environmentally friendly antibiotic adsorbent that can not only efficiently remove antibiotics from water but also recycle industrial alkali lignin waste.

Response surface optimization of product yields and biofuel quality during fast hydrothermal liquefaction of a highly CO2-tolerant microalgae

The effects of biochemical components and processing variables (e.g., temperatures, solid-liquid ratio, ethanol concentration, and time) during fast hydrothermal liquefaction of a highly CO₂-tolerant microalgae (Micractinium sp.) on the product yields and biofuel quality were explored using response surface methodology coupled with central composite design. Results showed that the maximum bio-oil yield (51.4 %) was obtained at 321 °C for 49 min at ethanol concentration of 75 % and solid-liquid ratio of 15.3 %. Among different studied parameters, ethanol concentration showed the highest significant impact on the bio-oil yield due to the low P-value and high F-value in ANOVA analysis. Furthermore, the chemical compositions of bio-oils were determined, which showed that the increase of ethanol concentration in the solvent not only increased the bio-oil yield but also promoted the bio-oil quality by reduction of carboxylic acids and nitrogen-containing compounds with simultaneous enhancement of esters in the bio-oil. The present results show that fast hydrothermal liquefaction is a promising approach to convert the microalgae into high quality biofuels rich in esters.

Edge-oriented phosphatizing engineering of 2D Ni-MOFs with a tailored d-band center for boosting catalytic activity

Metal-organic framework (MOF)-based heterostructures have aroused widespread interest owing to their extensive compositional tunability and interesting catalytic properties. However, the precise edge-oriented growth of transition metal compounds at the edges of 2D MOFs to construct edge mode heterostructures remains a great challenge due to their inherent thermodynamic instability. Here, edge-oriented growth of Ni₂P at the edges of a 2D Ni-MOF was achieved for the first time by precisely tuning the phosphorus source content and phosphating temperature. Owing to the formation of the edge mode Ni-MOF/Ni₂P heterostructure, the as-prepared heterostructure showed upregulated d-band center, more robust 4-nitrophenol (4-NP) adsorption capacity, lowered energy barrier of the rate-determining step (RDS), and higher specific surface area, resulting in the best performance of the hydrogenation reduction of 4-NP to 4-aminophenol (4-AP) in the presence of non-precious metal catalysts.

Lanthanum-modified polydopamine loaded Acinetobacter lwoffii DNS32 for phosphate and atrazine removal: Insights into co-adsorption and biodegradation mechanisms

A novel biobased composite was developed for the removal of phosphate (P) and atrazine from agricultural wastewater. A composite with strong P affinity and good biocompatibility, synthesized from La³⁺ and polydopamine (PDA), was immobilized onto an atrazine-degrading bacterium Acinetobacter lwoffii DNS32 (La/PDA/DNS32). Following Box-Behnken design optimization, the maximum removal rate of P (500 mg L^-1) and atrazine (100 mg L^-1) by La/PDA/DNS32 reached 28 % and 100 %, respectively. Density functional theory calculations revealed that La/PDA had more negative adsorption energy (-5.90 eV) than PDA alone and exhibited prominent electrophilic sites. Additionally, La/PDA-induced sorption of atrazine improved transmembrane transport and enhanced expression of degradation-associated genes in strain DNS32. La/PDA nanoparticles surrounding strain DNS32 provided a shielding effect and exhibited desirable biostability, thermal stability, and acid-alkaline resistance under contamination stress. This study demonstrates the promising potential of La/PDA/DNS32 in reducing the P and atrazine pollution caused by agricultural production.