Field and Laboratory Evaluations of the Low-Cost Plantower Particulate Matter Sensor

Catastrophic impact of extreme 2019 Indonesian peatland fires on urban air quality and health

Tropical peatland fires generate substantial quantities of airborne fine particulate matter (PM2.5) and in Indonesia are intensified during El Niño-related drought leading to severe air quality impacts affecting local and distant populations. Limited in-situ data often necessitates reliance on air quality models, like that of the Copernicus Atmosphere Monitoring Service, whose accuracy in extreme conditions is not fully understood. Here we demonstrate how a network of low-cost sensors around Palangka Raya, Central Kalimantan during the 2019 fire season, quantified extreme air quality and city-scale variability. The data indicates relatively strong model performance. Health impacts are substantial with estimates of over 1200 excess deaths in the Palangka Raya region, over 3200 across Central Kalimantan and more than 87,000 nationwide in 2019 due to fire-induced PM2.5 exposure. These findings highlight the need for urgent action to mitigate extreme fire events, including reducing fire use and landscape remediation to prevent peat fire ignition.

Updated Smoke Exposure Estimate for Indonesian Peatland Fires Using a Network of Low-Cost PM2.5 Sensors and a Regional Air Quality Model

Indonesia accounts for more than one third of the world's tropical peatlands. Much of the peatland in Indonesia has been deforested and drained, meaning it is more susceptible to fires, especially during drought and El Niño events. Fires are most common in Riau (Sumatra) and Central Kalimantan (Borneo) and lead to poor regional air quality. Measurements of air pollutant concentrations are sparse in both regions contributing to large uncertainties in both fire emissions and air quality degradation. We deployed a network of 13 low-cost PM2.5 sensors across urban and rural locations in Central Kalimantan and measured indoor and outdoor PM2.5 concentrations during the onset of an El Niño dry season in 2023. During the dry season (September 1st to October 31st), mean outdoor PM2.5 concentrations were 136 μg m-3, with fires contributing 90 μg m-3 to concentrations. Median indoor/outdoor (I/O) ratios were 1.01 in rural areas, considerably higher than those reported during wildfires in other regions of the world (e.g., USA), indicating housing stock in the region provides little protection from outdoor PM2.5. We combined WRF-Chem simulated PM2.5 concentrations with the median fire-derived I/O ratio and questionnaire results pertaining to participants' time spent I/O to estimate 1.62 million people in Central Kalimantan were exposed to unhealthy, very unhealthy and dangerous air quality (>55.4 μg m-3) during the dry season. Our work provides new information on the exposure of people in Central Kalimantan to smoke from fires and highlights the need for action to help reduce peatland fires.

Mobile laboratory measurements of air pollutants in Baltimore, MD elucidate issues of environmental justice

The City of Baltimore, MD has a history of problems with environmental justice (EJ), air pollution, and the urban heat island (UHI) effect. Current chemical transport models lack the resolution to simulate concentrations on the scale needed, about 100 m, to identify the neighborhoods with anomalously high air pollution levels. In this paper we introduce the capabilities of a mobile laboratory and an initial survey of several pollutants in Baltimore to identify which communities are exposed to disproportionate concentrations of air pollution and to which species. High concentrations of black carbon (BC) stood out at some locations - near major highways, downtown, and in the Curtis Bay neighborhood of Baltimore. Results from the mobile lab are confirmed with longer-term, low-cost monitoring. In Curtis Bay, higher concentrations of BC were measured along Pennington Ave. (mean [5th to 95th percentiles] = 2.08 [2.0-10.9] μg m-3) than along Curtis Ave. just ~ 150 m away (0.67[0.1 - 1.8] μg m-3). Other species, including criteria pollutants ozone (O3), carbon monoxide (CO), nitrogen dioxide (NO2), sulfur dioxide (SO2), and fine particulate matter (PM2.5), showed little gradient. Observations with high spatial and temporal resolution help isolate the mechanisms leading to locally high pollutant concentrations. The difference in BC appears to result not from heavier truck traffic or slower dispersion but from the interruptions in traffic flow. Pennington Ave. has three stoplights while Curtis Ave. has none. As heavy-duty diesel-powered vehicles accelerate, they experience turbo-lag and the resulting rich air-fuel mixture exacerbates BC emissions. Immediate mediation might be achieved through smoother traffic flow, and the long-term solution through replacing heavy-duty trucks with electric vehicles.Implications: We present results documenting the locations within Baltimore of high concentrations of Black Carbon pollution and identify the likely source - diesel exhaust emissions exacerbated by stop-and-go traffic and associated turbo-lag. This suggests solutions (smoother traffic, retrofit particulate filters, replacement of diesel with electric vehicles) that would enhance Environmental Justice (EJ) and could be applied to other cities with EJ problems.Synopsis: This paper presents observations of atmospheric black carbon aerosol showing impacts on environmental justice, then identifies causes and suggests solutions.

A wearable real-time particulate monitor demonstrates that soaking hay reduces dust exposure

BACKGROUND

Affordable particulate matter (PM) monitors suitable for use on horses will facilitate the evaluation of PM mitigation methods and improve the management of equine asthma.

OBJECTIVE

Calibrate a real-time wearable PM monitor (Black Beauty [BB]) and compare the PM exposures of horses fed dry or soaked hay.

STUDY DESIGN

Laboratory calibration; complete cross-over feed trial.

METHODS

Side-by-side sampling with BB monitors and tapered element oscillating microbalances (TEOMs) was performed under varying concentrations of PM from alfalfa hay. Linear regression was used to derive a calibration formula for each unit based on TEOM PM measurements. Precision was evaluated by calculating the coefficient of variation and pairwise correlation coefficients between three BB monitors. PM exposure was measured at the breathing zone of 10 horses for 8 h after they were fed dry or soaked hay. Repeated measures generalised linear models were constructed to determine the effect of hay treatment and measurement duration (initial 20-min vs. 8-h) upon exposure to PM with diameters smaller than or equal to 10 μm (PM10) and 2.5 μm (PM2.5).

RESULTS

BB monitor PM2.5 and PM10 measurements were linearly correlated with TEOM data (coefficient of determination r2 > 0.85 and r2 > 0.90 respectively), but underestimated PM2.5 mass concentrations by a factor of 4 and PM10 concentrations by a factor of 44. Measures from the three BB monitors had a coefficient of variation <15% and pairwise r > 0.98. Feeding soaked hay significantly reduced average PM2.5 exposures (20-min: dry: 160 μg/m3, soaked: 53 μg/m3, p < 0.0001; 8-h: dry: 76 μg/m3, soaked: 31 μg/m3, p = 0.0008) and PM10 exposures (20-min: dry: 2829 μg/m3, soaked: 970 μg/m3, p < 0.0001; 8-h: dry: 1581 μg/m3, soaked: 488 μg/m3, p = 0.008).

MAIN LIMITATIONS

No health outcome measures were collected.

CONCLUSIONS

With appropriate corrections, the BB monitor can be used to estimate horse PM exposure. While 20-min measurements yielded higher estimates of exposure than 8-h measurements, both intervals demonstrate that soaking hay reduces PM exposures by more than 50%.

Feasibility of low-cost particulate matter sensors for long-term environmental monitoring: Field evaluation and calibration

Low-cost sensor networks offer the potential to reduce monitoring costs while providing high-resolution spatiotemporal data on pollutant levels. However, these sensors come with limitations, and many aspects of their field performance remain underexplored. During October to December 2023, this study deployed two identical low-cost sensor systems near an urban standard monitoring station to record PM2.5 and PM10 concentrations, along with environmental temperature and humidity. Our evaluation of the monitoring performance of these sensors revealed a broad data distribution with a systematic overestimation; this overestimation was more pronounced in PM10 readings. The sensors showed good consistency (R2 > 0.9, NRMSE<5 %), and normalization residuals were tracked to assess stability, which, despite occasional environmental influences, remained generally stable. A lateral comparison of four calibration models (MLR, SVR, RF, XGBoost) demonstrated superior performance of RF and XGBoost over others, particularly with RF showing enhanced effectiveness on the test set. SHAP analysis identified sensor readings as the most critical variable, underscoring their pivotal role in predictive modeling. Relative humidity consistently proved more significant than dew point and temperature, with higher RH levels typically having a positive impact on model outputs. The study indicates that, with appropriate calibration, sensors can supplement the sparse networks of regulatory-grade instruments, enabling dense neighborhood-scale monitoring and a better understanding of temporal air quality trends.

First Results From a Calibrated Network of Low-Cost PM2.5 Monitors in Mombasa, Kenya Show Exceedance of Healthy Guidelines

The paucity of fine particulate matter (PM2.5) measurements limits estimates of air pollution mortality in Sub-Saharan Africa. Well calibrated low-cost sensors can provide reliable data especially where reference monitors are unavailable. We evaluate the performance of Clarity Node-S PM monitors against a Tapered element oscillating microbalance (TEOM) 1400a and develop a calibration model in Mombasa, Kenya's second largest city. As-reported Clarity Node-S data from January 2023 through April 2023 was moderately correlated with the TEOM-1400a measurements (R 2 = 0.61) and exhibited a mean absolute error (MAE) of 7.03 μg m-3. Employing three calibration models, namely, multiple linear regression (MLR), Gaussian mixture regression and random forest (RF) decreased the MAE to 4.28, 3.93, and 4.40 μg m-3 respectively. The R 2 value improved to 0.63 for the MLR model but all other models registered a decrease (R 2 = 0.44 and 0.60 respectively). Applying the correction factor to a five-sensor network in Mombasa that was operated between July 2021 and July 2022 gave insights to the air quality in the city. The average daily concentrations of PM2.5 within the city ranged from 12 to 18 μg m-3. The concentrations exceeded the WHO daily PM2.5 limits more than 50% of the time, in particular at the sites nearby frequent industrial activity. Higher averages were observed during the dry and cold seasons and during early morning and evening periods of high activity. These results represent some of the first air quality monitoring measurements in Mombasa and highlight the need for more study.

Low-Cost Indoor Sensor Deployment for Predicting PM2.5 Exposure

Indoor air quality is critical to human health, as individuals spend an average of 90% of their time indoors. However, indoor particulate matter (PM) sensor networks are not deployed as often as outdoor sensor networks. In this study, indoor PM2.5 exposure is investigated via 2 low-cost sensor networks in Pittsburgh. The concentrations reported by the networks were fed into a Monte Carlo simulation to predict daily PM2.5 exposure for 4 demographics (indoor workers, outdoor workers, schoolchildren, and retirees). Additionally, this study compares the effects of 4 different correction factors on reported concentrations from the PurpleAir sensors, including both empirical and physics-based corrections. The results of the Monte Carlo simulation show that mean PM2.5 exposure varied by 1.5 μg/m3 or less when indoor and outdoor concentrations were similar. When indoor PM concentrations were lower than outdoor, increasing the time spent outdoors on the simulation increased exposure by up to 3 μg/m3. These differences in exposure highlight the importance of carefully selecting sites for sensor deployment and show the value of having a robust low-cost sensor network with both indoor and outdoor sensor placement.

Assessment of PM2.5 Concentration at University Transit Bus Stops Using Low-Cost Aerosol Monitors by Student Commuters

Particulate matter of 2.5 µm and smaller (PM2.5) is known to cause many respiratory health problems, such as asthma and heart disease. A primary source of PM2.5 is emissions from cars, trucks, and buses. Emissions from university transit bus systems could create zones of high PM2.5 concentration at their bus stops. This work recruited seven university students who regularly utilized the transit system to use a low-cost personal aerosol monitor (AirBeam) each time they arrived at a campus bus stop. Each participant measured PM2.5 concentrations every time they were at a transit-served bus stop over four weeks. PM2.5 concentration data from the AirBeam were compared with an ADR-1500 high-cost monitor and EPA PM2.5 reference measurements. This methodology allowed for identifying higher-than-average concentration zones at the transit bus stops compared to average measurements for the county. By increasing access to microenvironmental data, this project can contribute to public health efforts of personal protection and prevention by allowing individuals to measure and understand their exposure to PM2.5 at the bus stop. This work can also aid commuters, especially those with pre-existing conditions who use public transportation, in making more informed health decisions and better protecting themselves against new or worsening respiratory conditions.

Data Evaluation of a Low-Cost Sensor Network for Atmospheric Particulate Matter Monitoring in 15 Municipalities in Serbia

Conventional air quality monitoring networks typically tend to be sparse over areas of interest. Because of the high cost of establishing such monitoring systems, some areas are often completely left out of regulatory monitoring networks. Recently, a new paradigm in monitoring has emerged that utilizes low-cost air pollution sensors, thus making it possible to reduce the knowledge gap in air pollution levels for areas not covered by regulatory monitoring networks and increase the spatial resolution of monitoring in others. The benefits of such networks for the community are almost self-evident since information about the level of air pollution can be transmitted in real time and the data can be analysed immediately over the wider area. However, the accuracy and reliability of newly produced data must also be taken into account in order to be able to correctly interpret the results. In this study, we analyse particulate matter pollution data from a large network of low-cost particulate matter monitors that was deployed and placed in outdoor spaces in schools in central and western Serbia under the Schools for Better Air Quality UNICEF pilot initiative in the period from April 2022 to June 2023. The network consisted of 129 devices in 15 municipalities, with 11 of the municipalities having such extensive real-time measurements of particulate matter concentration for the first time. The analysis showed that the maximum concentrations of PM2.5 and PM10 were in the winter months (heating season), while during the summer months (non-heating season), the concentrations were several times lower. Also, in some municipalities, the maximum values and number of daily exceedances of PM10 (50 μg/m3) were much higher than in the others because of diversity and differences in the low-cost sensor sampling sites. The particulate matter mass daily concentrations obtained by low-cost sensors were analysed and also classified according to the European AQI (air quality index) applied to low-cost sensor data. This study confirmed that the large network of low-cost air pollution sensors can be useful in providing real-time information and warnings about higher pollution days and episodes, particularly in situations where there is a lack of local or national regulatory monitoring stations in the area.

Dissecting PM sensor capabilities: A combined experimental and theoretical study on particle sizing and physicochemical properties

Recent advancements in particulate matter (PM) optical measurement technology have enhanced the characterization of particle size distributions (PSDs) across various temporal and spatial scales, offering a more detailed analysis than traditional PM mass concentration monitoring. This study employs field experiments, laboratory tests, and model simulations to evaluate the influence of physicochemical characteristics of particulate matter (PM) on the performance of a compact, multi-channel PM sizing sensor. The sensor is integrated within a mini air station (MAS) designed to detect particles across 52 channels. The field experiments highlighted the sensor's ability to track hygroscopicity parameter κ-values across particle sizes, noting an increasing trend with particle size. The sensor's capability in identifying the size and mass concentration of different PM types, including ammonium nitrate, sodium chloride, smoke, incense, and silica dust particles, was assessed through laboratory tests. Laboratory comparisons with the Aerodynamic Particle Sizer (APS) showed high consistency (R2 > 0.96) for various PM sources, supported by Kolmogorov-Smirnov tests confirming the sensor's capability to match APSsize distributions. Model simulations further elucidated the influence of particle refractive index and size distributions on sensor performance, leading to optimized calibrant selection and application-specific recommendations. These comprehensive evaluations underscore the critical interplay between the chemical composition and physical properties of PM, significantly advancing the application and reliability of optical PM sensors in environmental monitoring.

Multi-Scenario Validation and Assessment of a Particulate Matter Sensor Monitor Optimized by Machine Learning Methods

OBJECTIVE

The aim was to evaluate and optimize the performance of sensor monitors in measuring PM2.5 and PM10 under typical emission scenarios both indoors and outdoors.

METHOD

Parallel measurements and comparisons of PM2.5 and PM10 were carried out between sensor monitors and standard instruments in typical indoor (2 months) and outdoor environments (1 year) in Shanghai, respectively. The optimized validation model was determined by comparing six machining learning models, adjusting for meteorological and related factors. The intra- and inter-device variation, measurement accuracy, and stability of sensor monitors were calculated and compared before and after validation.

RESULTS

Indoor particles were measured in a range of 0.8-370.7 μg/m3 and 1.9-465.2 μg/m3 for PM2.5 and PM10, respectively, while the outdoor ones were in the ranges of 1.0-211.0 μg/m3 and 0.0-493.0 μg/m3, correspondingly. Compared to machine learning models including multivariate linear model (ML), K-nearest neighbor model (KNN), support vector machine model (SVM), decision tree model (DT), and neural network model (MLP), the random forest (RF) model showed the best validation after adjusting for temperature, relative humidity (RH), PM2.5/PM10 ratios, and measurement time lengths (months) for both PM2.5 and PM10, in indoor (R2: 0.97 and 0.91, root-mean-square error (RMSE) of 1.91 μg/m3 and 4.56 μg/m3, respectively) and outdoor environments (R2: 0.90 and 0.80, RMSE of 5.61 μg/m3 and 17.54 μg/m3, respectively), respectively.

CONCLUSIONS

Sensor monitors could provide reliable measurements of PM2.5 and PM10 with high accuracy and acceptable inter and intra-device consistency under typical indoor and outdoor scenarios after validation by RF model. Adjusting for both climate factors and the ratio of PM2.5/PM10 could improve the validation performance.

Selective Detection of Functionalized Carbon Particles based on Polymer Semiconducting and Conducting Devices as Potential Particulate Matter Sensors

This paper reports a new mechanism for particulate matter detection and identification. Three types of carbon particles are synthesized with different functional groups to mimic the real particulates in atmospheric aerosol. After exposing polymer-based organic devices in organic field effect transistor (OFET) architectures to the particle mist, the sensitivity and selectivity of the detection of different types of particles are shown by the current changes extracted from the transfer curves. The results indicate that the sensitivity of the devices is related to the structure and functional groups of the organic semiconducting layers, as well as the morphology. The predominant response is simulated by a model that yielded values of charge carrier density increase and charge carriers delivered per unit mass of particles. The research points out that polymer semiconductor devices have the ability to selectively detect particles with multiple functional groups, which reveals a future direction for selective detection of particulate matter.

A DYNAMIC SPATIAL FILTERING APPROACH TO MITIGATE UNDERESTIMATION BIAS IN FIELD CALIBRATED LOW-COST SENSOR AIR POLLUTION DATA

Low-cost air pollution sensors, offering hyper-local characterization of pollutant concentrations, are becoming increasingly prevalent in environmental and public health research. However, low-cost air pollution data can be noisy, biased by environmental conditions, and usually need to be field-calibrated by collocating low-cost sensors with reference-grade instruments. We show, theoretically and empirically, that the common procedure of regression-based calibration using collocated data systematically underestimates high air pollution concentrations, which are critical to diagnose from a health perspective. Current calibration practices also often fail to utilize the spatial correlation in pollutant concentrations. We propose a novel spatial filtering approach to collocation-based calibration of low-cost networks that mitigates the underestimation issue by using an inverse regression. The inverse-regression also allows for incorporating spatial correlations by a second-stage model for the true pollutant concentrations using a conditional Gaussian Process. Our approach works with one or more collocated sites in the network and is dynamic, leveraging spatial correlation with the latest available reference data. Through extensive simulations, we demonstrate how the spatial filtering substantially improves estimation of pollutant concentrations, and measures peak concentrations with greater accuracy. We apply the methodology for calibration of a low-cost PM2.5 network in Baltimore, Maryland, and diagnose air pollution peaks that are missed by the regression-calibration.

Evaluation of Calibration Approaches for Indoor Deployments of PurpleAir Monitors

Low-cost air quality monitors are growing in popularity among both researchers and community members to understand variability in pollutant concentrations. Several studies have produced calibration approaches for these sensors for ambient air. These calibrations have been shown to depend primarily on relative humidity, particle size distribution, and particle composition, which may be different in indoor environments. However, despite the fact that most people spend the majority of their time indoors, little is known about the accuracy of commonly used devices indoors. This stems from the fact that calibration data for sensors operating in indoor environments are rare. In this study, we sought to evaluate the accuracy of the raw data from PurpleAir fine particulate matter monitors and for published calibration approaches that vary in complexity, ranging from simply applying linear corrections to those requiring co-locating a filter sample for correction with a gravimetric concentration during a baseline visit. Our data includes PurpleAir devices that were co-located in each home with a gravimetric sample for 1-week periods (265 samples from 151 homes). Weekly-averaged gravimetric concentrations ranged between the limit of detection (3 μg/m3) and 330 μg/m3. We found a strong correlation between the PurpleAir monitor and the gravimetric concentration (R>0.91) using internal calibrations provided by the manufacturer. However, the PurpleAir data substantially overestimated indoor concentrations compared to the gravimetric concentration (mean bias error ≥ 23.6 μg/m3 using internal calibrations provided by the manufacturer). Calibrations based on ambient air data maintained high correlations (R ≥ 0.92) and substantially reduced bias (e.g. mean bias error = 10.1 μg/m3 using a US-wide calibration approach). Using a gravimetric sample from a baseline visit to calibrate data for later visits led to an improvement over the internal calibrations, but performed worse than the simpler calibration approaches based on ambient air pollution data. Furthermore, calibrations based on ambient air pollution data performed best when weekly-averaged concentrations did not exceed 30 μg/m3, likely because the majority of the data used to train these models were below this concentration.

Laboratory Comparison of Low-Cost Particulate Matter Sensors to Measure Transient Events of Pollution-Part B-Particle Number Concentrations

Low-cost Particulate Matter (PM) sensors offer an excellent opportunity to improve our knowledge about this type of pollution. Their size and cost, which support multi-node network deployment, along with their temporal resolution, enable them to report fine spatio-temporal resolution for a given area. These sensors have known issues across performance metrics. Generally, the literature focuses on the PM mass concentration reported by these sensors, but some models of sensors also report Particle Number Concentrations (PNCs) segregated into different PM size ranges. In this study, eight units each of Alphasense OPC-R1, Plantower PMS5003 and Sensirion SPS30 have been exposed, under controlled conditions, to short-lived peaks of PM generated using two different combustion sources of PM, exposing the sensors' to different particle size distributions to quantify and better understand the low-cost sensors performance across a range of relevant environmental ranges. The PNCs reported by the sensors were analysed to characterise sensor-reported particle size distribution, to determine whether sensor-reported PNCs can follow the transient variations of PM observed by the reference instruments and to determine the relative impact of different variables on the performances of the sensors. This study shows that the Alphasense OPC-R1 reported at least five size ranges independently from each other, that the Sensirion SPS30 reported two size ranges independently from each other and that all the size ranges reported by the Plantower PMS5003 were not independent of each other. It demonstrates that all sensors tested here could track the fine temporal variation of PNCs, that the Alphasense OPC-R1 could closely follow the variations of size distribution between the two sources of PM, and it shows that particle size distribution and composition are more impactful on sensor measurements than relative humidity.

Enhancing the reliability of particulate matter sensing by multivariate Tobit model using weather and air quality data

Low-cost particulate matter (PM) sensors have been widely used following recent sensor-technology advancements; however, inherent limitations of low-cost monitors (LCMs), which operate based on light scattering without an air-conditioning function, still restrict their applicability. We propose a regional calibration of LCMs using a multivariate Tobit model with historical weather and air quality data to improve the accuracy of ambient air monitoring, which is highly dependent on meteorological conditions, local climate, and regional PM properties. Weather observations and PM2.5 (fine inhalable particles with diameters ≤ 2.5 μm) concentrations from two regions in Korea, Incheon and Jeju, and one in Singapore were used as training data to build a visibility-based calibration model. To validate the model, field measurements were conducted by an LCM in Jeju and Singapore, where R2 and the error after applying the model in Jeju improved (from 0.85 to 0.88) and reduced by 44% (from 8.4 to 4.7 μg m-3), respectively. The results demonstrated that regional calibration involving air temperature, relative humidity, and other local climate parameters can efficiently correct the bias of the sensor. Our findings suggest that the proposed post-processing using the Tobit model with regional weather and air quality data enhances the applicability of LCMs.

Investigating the Sensitivity of Low-Cost Sensors in Measuring Particle Number Concentrations across Diverse Atmospheric Conditions in Greece and Spain

Low-cost sensors (LCSs) for particulate matter (PM) concentrations have attracted the interest of researchers, supplementing their efforts to quantify PM in higher spatiotemporal resolution. The precision of PM mass concentration measurements from PMS 5003 sensors has been widely documented, though limited information is available regarding their size selectivity and number concentration measurement accuracy. In this work, PMS 5003 sensors, along with a Federal Referral Methods (FRM) sampler (Grimm spectrometer), were deployed across three sites with different atmospheric profiles, an urban (Germanou) and a background (UPat) site in Patras (Greece), and a semi-arid site in Almería (Spain, PSA). The LCSs particle number concentration measurements were investigated for different size bins. Findings for particles with diameter between 0.3 and 10 μm suggest that particle size significantly affected the LCSs' response. The LCSs could accurately detect number concentrations for particles smaller than 1 μm in the urban (R² = 0.9) and background sites (R² = 0.92), while a modest correlation was found with the reference instrument in the semi-arid area (R² = 0.69). However, their performance was rather poor (R² < 0.31) for coarser aerosol fractions at all sites. Moreover, during periods when coarse particles were dominant, i.e., dust events, PMS 5003 sensors were unable to report accurate number distributions (R² values < 0.47) and systematically underestimated particle number concentrations. The results indicate that several questions arise concerning the sensors' capabilities to estimate PM_2.5 and PM₁₀ concentrations, since their size distribution did not agree with the reference instruments.

Performance-based protocol for selection of economical portable sensor for air quality measurement

An effective micro-level air quality management plan requires high-resolution monitoring of pollutants. India has already developed a vast network of air quality monitoring stations, both manual and real time, located primarily in urban areas, including megacities. The air quality monitoring network consists of conventional manual stations and real time Continuous Ambient Air Quality Monitoring Stations (CAAQMS) which comprise state-of-the-art analysers and instruments. India is currently in the early stages of developing and adopting economical portable sensor (EPS) in air quality monitoring systems. Protocols need to be established for field calibration and testing. The present research work is an attempt to develop a performance-based assessment framework for the selection of EPS for air quality monitoring. The two-stage selection protocol includes a review of the factory calibration data and a comparison of EPS data with a reference monitor, i.e. a portable calibrated monitor and a CAAQMS. Methods deployed include calculation of central tendency, dispersion around a central value, calculation of statistical parameters for data comparison, and plotting pollution rose and diurnal profile (peak and non-peak pollution measurement). Four commercially available EPS were tested blind, out of which, data from EPS 2 (S2) and EPS 3 (S3) were closer to reference stations at both locations. The selection was made by evaluating monitoring results, physical features, measurement range, and frequency along with examining capital cost. This proposed approach can be used to increase the usability of EPS in the development of micro-level air quality management strategies, other than regulatory compliance. For regulatory compliance, additional research is needed, including field calibration and evaluating EPS performance through additional variables. This proposed framework may be used as starting point, for such experiments, in order to develop confidence in the use of EPS.

Spatial Variation of PM2.5 Indoors and Outdoors: Results from 261 Regulatory Monitors Compared to 14,000 Low-Cost Monitors in Three Western States over 4.7 Years

Spatial variation of indoor and outdoor PM_2.5 within three states for a five-year period is studied using regulatory and low-cost PurpleAir monitors. Most of these data were collected in an earlier study (Wallace et al., 2022 Indoor Air 32:13105) investigating the relative contribution of indoor-generated and outdoor-infiltrated particles to indoor exposures. About 260 regulatory monitors and ~10,000 outdoor and ~4000 indoor PurpleAir monitors are included. Daily mean PM_2.5 concentrations, correlations, and coefficients of divergence (COD) are calculated for pairs of monitors at distances ranging from 0 (collocated) to 200 km. We use a transparent and reproducible open algorithm that avoids the use of the proprietary algorithms provided by the manufacturer of the sensors in PurpleAir PA-I and PA-II monitors. The algorithm is available on the PurpleAir API website under the name "PM_2.5_alt". This algorithm is validated using several hundred pairs of regulatory and PurpleAir monitors separated by up to 0.5 km. The PM_2.5 spatial variation outdoors is homogeneous with high correlations to at least 10 km, as shown by the COD index under 0.2. There is also a steady improvement in outdoor PM_2.5 concentrations with increasing distance from the regulatory monitors. The spatial variation of indoor PM_2.5 is not homogeneous even at distances < 100 m. There is good agreement between PurpleAir outdoor monitors located <100 m apart and collocated Federal Equivalent Methods (FEM).

Unexpected Performance Improvements of Nitrogen Dioxide and Ozone Sensors by Including Carbon Monoxide Sensor Signal

Low-cost air quality (LCAQ) sensors are increasingly being used for community air quality monitoring. However, data collected by low-cost sensors contain significant noise, and proper calibration of these sensors remains a widely discussed, but not yet fully addressed, area of concern. In this study, several LCAQ sensors measuring nitrogen dioxide (NO2) and ozone (O3) were deployed in six cities in the United States (Atlanta, GA; New York City, NY; Sacramento, CA; Riverside, CA; Portland, OR; Phoenix, AZ) to evaluate the impacts of different climatic and geographical conditions on their performance and calibration. Three calibration methods were applied, including regression via linear and polynomial models and random forest methods. When signals from carbon monoxide (CO) sensors were included in the calibration models for NO2 and O3 sensors, model performance generally increased, with pronounced improvements in selected cities such as Riverside and New York City. Such improvements may be due to (1) temporal co-variation between concentrations of CO and NO2 and/or between CO and O3; (2) different performance levels of low-cost CO, NO2, and O3 sensors; and (3) different impacts of environmental conditions on sensor performance. The results showed an innovative approach for improving the calibration of NO2 and O3 sensors by including CO sensor signals into the calibration models. Community users of LCAQ sensors may be able to apply these findings further to enhance the data quality of their deployed NO2 and O3 monitors.

Identifying optimal co-location calibration periods for low-cost sensors

Low-cost sensors are often co-located with reference instruments to assess their performance and establish calibration equations, but limited discussion has focused on whether the duration of this calibration period can be optimized. We placed a multipollutant monitor that contained sensors that measure particulate matter smaller than 2.5 μm (PM_2.5), carbon monoxide (CO), nitrogen dioxide (NO₂), ozone (O₃), and nitric oxide (NO) at a reference field site for one year. We developed calibration equations using randomly selected co-location subsets spanning 1 to 180 consecutive days out of the 1-year period and compared the potential root mean square errors (RMSE) and Pearson correlation coefficients (r). The co-located calibration period required to obtain consistent results varied by sensor type, and several factors increased the co-location duration required for accurate calibration, including the response of a sensor to environmental factors, such as temperature or relative humidity (RH), or cross-sensitivities to other pollutants. Using measurements from Baltimore, MD, where a broad range of environmental conditions may be observed over a given year, we found diminishing improvements in the median RMSE for calibration periods longer than about six weeks for all the sensors. The best performing calibration periods were the ones that contained a range of environmental conditions similar to those encountered during the evaluation period (i.e., all other days of the year not used in the calibration). With optimal, varying conditions it was possible to obtain an accurate calibration in as little as one week for all sensors, suggesting that co-location can be minimized if the period is strategically selected and monitored so that the calibration period is representative of the desired measurement setting.

Wearable Sensor-Based Monitoring of Environmental Exposures and the Associated Health Effects: A Review

Recent advances in sensor technology have facilitated the development and use of personalized sensors in monitoring environmental factors and the associated health effects. No studies have reviewed the research advancement in examining population-based health responses to environmental exposure via portable sensors/instruments. This study aims to review studies that use portable sensors to measure environmental factors and health responses while exploring the environmental effects on health. With a thorough literature review using two major English databases (Web of Science and PubMed), 24 eligible studies were included and analyzed out of 16,751 total records. The 24 studies include 5 on physical factors, 19 on chemical factors, and none on biological factors. The results show that particles were the most considered environmental factor among all of the physical, chemical, and biological factors, followed by total volatile organic compounds and carbon monoxide. Heart rate and heart rate variability were the most considered health indicators among all cardiopulmonary outcomes, followed by respiratory function. The studies mostly had a sample size of fewer than 100 participants and a study period of less than a week due to the challenges in accessing low-cost, small, and light wearable sensors. This review guides future sensor-based environmental health studies on project design and sensor selection.

Evaluation of a new low-cost particle sensor as an internet-of-things device for outdoor air quality monitoring

Many low-cost particle sensors are available for routine air quality monitoring of PM_2.5, but there are concerns about the accuracy and precision of the reported data, particularly in humid conditions. The objectives of this study are to evaluate the Sensirion SPS30 particulate matter (PM) sensor against regulatory methods for measurement of real-time particulate matter concentrations and to evaluate the effectiveness of the Intelligent Air^TM sensor pack for remote deployment and monitoring. To achieve this, we co-located the Intelligent Air^TM sensor pack, developed at Clemson University and built around the Sensirion SPS30, to collect data from July 29, 2019, to December 12, 2019, at a regulatory site in Columbia, South Carolina. When compared to the Federal Equivalent Methods, the SPS30 showed an average bias adjusted R² = 0.75, mean bias error of -1.59, and a root mean square error of 2.10 for 24-hour average trimmed measurements over 93 days, and R² = 0.57, mean bias error of -1.61, and a root mean square error of 3.029, for 1-hr average trimmed measurements over 2300 hours when the central 99% of data was retained with a data completeness of 75% or greater. The Intelligent Air^TM sensor pack is designed to promote long-term deployment and includes a solar panel and battery backup, protection from the elements, and the ability to upload data via a cellular network. Overall, we conclude that the SPS30 PM sensor and the Intelligent Air^TM sensor pack have the potential for greatly increasing the spatial density of particulate matter measurements, but more work is needed to understand and calibrate sensor measurements.Implications: This work adds to the growing body of research that indicates that low-cost sensors of particulate matter (PM) for air quality monitoring has a promising future, and yet much work is left to be done. This work shows that the level of data processing and filtering effects how the low-cost sensors compare to existing federal reference and equivalence methods: more data filtering at low PM levels worsens the data comparison, while longer time averaging improves the measurement comparisons. Improvements must be made to how we handle, calibrate, and correct PM data from low-cost sensors before the data can be reliably used for air quality monitoring and attainment.

Non-linear probabilistic calibration of low-cost environmental air pollution sensor networks for neighborhood level spatiotemporal exposure assessment

BACKGROUND

Low-cost sensor networks for monitoring air pollution are an effective tool for expanding spatial resolution beyond the capabilities of existing state and federal reference monitoring stations. However, low-cost sensor data commonly exhibit non-linear biases with respect to environmental conditions that cannot be captured by linear models, therefore requiring extensive lab calibration. Further, these calibration models traditionally produce point estimates or uniform variance predictions which limits their downstream in exposure assessment.

OBJECTIVE

Build direct field-calibration models using probabilistic gradient boosted decision trees (GBDT) that eliminate the need for resource-intensive lab calibration and that can be used to conduct probabilistic exposure assessments on the neighborhood level.

METHODS

Using data from Plantower A003 particulate matter (PM) sensors deployed in Baltimore, MD from November 2018 through November 2019, a fully probabilistic NGBoost GBDT was trained on raw data from sensors co-located with a federal reference monitoring station and compared against linear regression trained on lab calibrated sensor data. The NGBoost predictions were then used in a Monte Carlo interpolation process to generate high spatial resolution probabilistic exposure gradients across Baltimore.

RESULTS

We demonstrate that direct field-calibration of the raw PM2.5 sensor data using a probabilistic GBDT has improved point and distribution accuracies compared to the linear model, particularly at reference measurements exceeding 25 μg/m3, and also on monitors not included in the training set.

SIGNIFICANCE

We provide a framework for utilizing the GBDT to conduct probabilistic spatial assessments of human exposure with inverse distance weighting that predicts the probability of a given location exceeding an exposure threshold and provides percentiles of exposure. These probabilistic spatial exposure assessments can be scaled by time and space with minimal modifications. Here, we used the probabilistic exposure assessment methodology to create high quality spatial-temporal PM2.5 maps on the neighborhood-scale in Baltimore, MD.

IMPACT STATEMENT

We demonstrate how the use of open-source probabilistic machine learning models for in-place sensor calibration outperforms traditional linear models and does not require an initial laboratory calibration step. Further, these probabilistic models can create uniquely probabilistic spatial exposure assessments following a Monte Carlo interpolation process.

The Impact of Meteorological Conditions and Agricultural Waste Burning on PM Levels: A Case Study of Avellino (Southern Italy)

In this work, the effect of the meteorological conditions and the agricultural waste burning on PM air pollution levels has been investigated in the city of Avellino, located in the Sabato Valley (southern Italy). Avellino has been described among the most polluted towns in Italy in terms of particulate matter (PM) during the last 10 years. The main aim of this study was to analyze the air quality data collected in Avellino and its surroundings during September 2021. In this period, the air quality in the Sabato Valley has been adversely affected by agricultural practices, which represent a significant source of PM. The impact of agricultural waste burning on PM levels in Avellino has been determined through an integrated monitoring network, consisting of two fixed urban reference stations and by several low-cost sensors distributed in the Sabato Valley. In the considered period, the two reference stations recorded several exceedances of the daily average PM₁₀ legislative limit value (50 µg m^-3) in addition to high concentrations of PM_2.5. Moreover, we provide a detailed description of the event that took place on 25 September 2021, when the combined effect of massive agricultural practices and very stable atmospheric conditions produced a severe pollution episode. Results show PM exceedances in Avellino concurrent with high PM values in the areas bordering the city due to agricultural waste burning and adverse meteorological conditions, which inhibit PM dispersion in the atmosphere.

Feasibility of low-cost particle sensor types in long-term indoor air pollution health studies after repeated calibration, 2019-2021

Previous studies have explored using calibrated low-cost particulate matter (PM) sensors, but important research gaps remain regarding long-term performance and reliability. Evaluate longitudinal performance of low-cost particle sensors by measuring sensor performance changes over 2 years of use. 51 low-cost particle sensors (Airbeam 1 N = 29; Airbeam 2 N = 22) were calibrated four times over a 2-year timeframe between 2019 and 2021. Cigarette smoke-specific calibration curves for Airbeam 1 and 2 PM sensors were created by directly comparing simultaneous 1-min readings of a Thermo Scientific Personal DataRAM PDR-1500 unit with a 2.5 µm inlet. Inter-sensor variability in calibration coefficient was high, particularly in Airbeam 1 sensors at study initiation. Calibration coefficients for both sensor types trended downwards over time to < 1 at final calibration timepoint [Airbeam 1 Mean (SD) = 0.87 (0.20); Airbeam 2 Mean (SD) = 0.96 (0.27)]. We lost more Airbeam 1 sensors (N = 27 out of 56, failure rate 48.2%) than Airbeam 2 (N = 2 out of 24, failure rate 8.3%) due to electronics, battery, or data output issues. Evidence suggests degradation over time might depend more on particle sensor type, rather than individual usage. Repeated calibrations of low-cost particle sensors may increase confidence in reported PM levels in longitudinal indoor air pollution studies.

Real-Time Monitoring of Gas-Phase and Dissolved CO2 Using a Mixed-Matrix Composite Integrated Fiber Optic Sensor for Carbon Storage Application

Novel chemical sensors that improve detection and quantification of CO₂ are critical to ensuring safe and cost-effective monitoring of carbon storage sites. Fiber optic (FO)-based chemical sensor systems are promising field-deployable systems for real-time monitoring of CO₂ in geological formations for long-range distributed sensing. In this work, a mixed-matrix composite integrated FO sensor system was developed with a purely optical readout that reliably operates as a detector for gas-phase and dissolved CO₂. A mixed-matrix composite sensor coating consisting of plasmonic nanocrystals and hydrophobic zeolite embedded in a polymer matrix was integrated on the FO sensor. The mixed-matrix composite FO sensor showed excellent reversibility/stability in a high humidity environment and sensitivity to gas-phase CO₂ over a large concentration range. This remarkable sensing performance was enabled by using plasmonic nanocrystals to significantly enhance the sensitivity and a hydrophobic zeolite to effectively mitigate interference from water vapor. The sensor exhibited the ability to sense CO₂ in the presence of other geologically relevant gases, which is of importance for applications in geological formations. A prototype FO sensor configuration, which possesses a robust sensing capability for monitoring dissolved CO₂ in natural water, was demonstrated. Reproducibility was confirmed over many cycles, both in a laboratory setting and in the field. More importantly, we demonstrated on-line monitoring capabilities with a wireless telemetry system, which transferred the data from the field to a website. The combination of outstanding CO₂ sensing properties and facile coating processability makes this mixed-matrix composite FO sensor a good candidate for practical carbon storage applications.

Laboratory evaluation of low-cost air quality monitors and single sensors for monitoring typical indoor emission events in Dutch daycare centers

Daycare centers (DCCs) are where infants and toddlers (0-4 years old) spend the most time besides their homes. Given their higher susceptibility to the effects of air pollutants, as compared to older children and adults, indoor air quality (IAQ) is regarded as an essential parameter to monitor in DCCs. Recent advances in IAQ monitoring technologies have enabled the deployment of low-cost air quality monitors (LCMs) and single sensors (LCSs) to continuously monitor various indoor environments, and their performance testing should also be performed in the intended indoor applications. To our knowledge, there is no study evaluating the application of LCMs/LCSs in DCCs scenarios yet. Therefore, this study is aimed to assess the response of five types of LCMs (previously not tested) and five LCSs to typical DCCs emission activities in detecting multiple IAQ parameters, i.e., particulate matter, carbon dioxide, total volatile organic compounds, temperature, and relative humidity. These LCMs/LCSs were compared to outcomes from research-grade instruments (RGIs). All the experiments were performed in a climate chamber, where three kinds of typical activities (background; arts-and-crafts; cleaning; [in a total of 32 events]) were simulated by recruited subjects at two typical indoor climatic conditions (cool and dry [20 ± 1 °C & 40 ± 10%], warm and humid [26 ± 1 °C & 70 ± 5%]). Results showed that tested LCMs had the ability to capture DCCs activities by simultaneously monitoring multiple IAQ parameters, and LCMs/LCSs revealed a strong correlation with RGIs in most events (R2 values from 0.7 to 1), but, for some events, the magnitude of responses varied widely. Sensirion SCD41, an emerging CO2 sensor built on the photoacoustic sensing principle, had a more accurate performance than all tested NDIR-based CO2 sensors/monitors. In general, the study implies that the selection of LCMs/LCSs for a specific application of interest should be based on emission characteristics and space conditions.

Field measurements of indoor and community air quality in rural Beijing before, during, and after the COVID-19 lockdown

The coronavirus (COVID-19) lockdown in China is thought to have reduced air pollution emissions due to reduced human mobility and economic activities. Few studies have assessed the impacts of COVID-19 on community and indoor air quality in environments with diverse socioeconomic and household energy use patterns. The main goal of this study was to evaluate whether indoor and community air pollution differed before, during, and after the COVID-19 lockdown in homes with different energy use patterns. Using calibrated real-time PM2.5 sensors, we measured indoor and community air quality in 147 homes from 30 villages in Beijing over 4 months including periods before, during, and after the COVID-19 lockdown. Community pollution was higher during the lockdown (61 ± 47 μg/m3 ) compared with before (45 ± 35 μg/m3 , p < 0.001) and after (47 ± 37 μg/m3 , p < 0.001) the lockdown. However, we did not observe significantly increased indoor PM2.5 during the COVID-19 lockdown. Indoor-generated PM2.5 in homes using clean energy for heating without smokers was the lowest compared with those using solid fuel with/without smokers, implying air pollutant emissions are reduced in homes using clean energy. Indoor air quality may not have been impacted by the COVID-19 lockdown in rural settings in China and appeared to be more impacted by the household energy choice and indoor smoking than the COVID-19 lockdown. As clean energy transitions occurred in rural households in northern China, our work highlights the importance of understanding multiple possible indoor sources to interpret the impacts of interventions, intended or otherwise.

Laboratory and Field Evaluations of the GeoAir2 Air Quality Monitor for Use in Indoor Environments

Low-cost aerosol sensors open routes to exposure assessment and air monitoring in various indoor and outdoor environments. This study evaluated the accuracy of GeoAir2--a recently developed low-cost particulate matter (PM) monitor--using two types of aerosols (salt and dust), and the effect of changes in relative humidity on its measurements in laboratory settings. For the accuracy experiments, 32 units of GeoAir2 were used, and for the humidity experiments, 3 units of GeoAir2 were used, alongside the OPC-N3 low-cost sensor and MiniWRAS reference instrument. The normal distribution of slopes between the salt and dust aerosols was compared for the accuracy experiments. In addition, the performance of GeoAir2 in indoor environments was evaluated compared to the pDR-1500 reference instrument by collocating GeoAir2 and pDR-1500 at three different homes for five days. For salt and dust aerosols smaller than 2.5 μm (PM_2.5), both GeoAir2 (r = 0.96-0.99) and OPC-N3 (r = 0.98-0.99) were highly correlated with the MiniWRAS reference instrument. However, GeoAir2 was less influenced by changes in humidity than OPC-N3. While GeoAir2 reported an increase in mass concentrations ranging from 100% to 137% for low and high concentrations, an increase between 181% and 425% was observed for OPC-N3. The normal distribution of the slopes for the salt aerosols was narrower than dust aerosol, which shows closer slope similarities for salt aerosols. This study also found that GeoAir2 was highly correlated with the pDR-1500 reference instrument in indoor environments (r = 0.80-0.99). These results demonstrate potential for GeoAir2 for indoor air monitoring and exposure assessments.

Calibration of PurpleAir PA-I and PA-II Monitors Using Daily Mean PM2.5 Concentrations Measured in California, Washington, and Oregon from 2017 to 2021

Large quantities of real-time particle data are becoming available from low-cost particle monitors. However, it is crucial to determine the quality of these measurements. The largest network of monitors in the United States is maintained by the PurpleAir company, which offers two monitors: PA-I and PA-II. PA-I monitors have a single sensor (PMS1003) and PA-II monitors employ two independent PMS5003 sensors. We determine a new calibration factor for the PA-I monitor and revise a previously published calibration algorithm for PA-II monitors (ALT-CF3). From the PurpleAir API site, we downloaded 83 million hourly average PM_2.5 values in the PurpleAir database from Washington, Oregon, and California between 1 January 2017 and 8 September 2021. Daily outdoor PM_2.5 means from 194 PA-II monitors were compared to daily means from 47 nearby Federal regulatory sites using gravimetric Federal Reference Methods (FRM). We find a revised calibration factor of 3.4 for the PA-II monitors. For the PA-I monitors, we determined a new calibration factor (also 3.4) by comparing 26 outdoor PA-I sites to 117 nearby outdoor PA-II sites. These results show that PurpleAir PM_2.5 measurements can agree well with regulatory monitors when an optimum calibration factor is found.

Socioeconomic and Demographic Associations with Wintertime Air Pollution Exposures at Household, Community, and District Scales in Rural Beijing, China

The Chinese government implemented a national household energy transition program that replaced residential coal heating stoves with electricity-powered heat pumps for space heating in northern China. As part of a baseline assessment of the program, this study investigated variability in personal air pollution exposures within villages and between villages and evaluated exposure patterns by sociodemographic factors. We randomly recruited 446 participants in 50 villages in four districts in rural Beijing and measured 24 h personal exposures to fine particulate matter (PM_2.5) and black carbon (BC). The geometric mean personal exposure to PM_2.5 and BC was 72 and 2.5 μg/m³, respectively. The variability in PM_2.5 and BC exposures was greater within villages than between villages. Study participants who used traditional stoves as their dominant source of space heating were exposed to the highest levels of PM_2.5 and BC. Wealthier households tended to burn more coal for space heating, whereas less wealthy households used more biomass. PM_2.5 and BC exposures were almost uniformly distributed by socioeconomic status. Future work that combines these results with PM_2.5 chemical composition analysis will shed light on whether air pollution source contributors (e.g., industrial, traffic, and household solid fuel burning) follow similar distributions.

Laboratory Chamber Evaluation of Flow Air Quality Sensor PM2.5 and PM10 Measurements

The emergence of low-cost air quality sensors as viable tools for the monitoring of air quality at population and individual levels necessitates the evaluation of these instruments. The Flow air quality tracker, a product of Plume Labs, is one such sensor. To evaluate these sensors, we assessed 34 of them in a controlled laboratory setting by exposing them to PM₁₀ and PM_2.5 and compared the response with Plantower A003 measurements. The overall coefficient of determination (R²) of measured PM_2.5 was 0.76 and of PM₁₀ it was 0.73, but the Flows’ accuracy improved after each introduction of incense. Overall, these findings suggest that the Flow can be a useful air quality monitoring tool in air pollution areas with higher concentrations, when incorporated into other monitoring frameworks and when used in aggregate. The broader environmental implications of this work are that it is possible for individuals and groups to monitor their individual exposure to particulate matter pollution.

Evaluating the Performance of Using Low-Cost Sensors to Calibrate for Cross-Sensitivities in a Multipollutant Network

As part of our low-cost sensor network, we colocated multipollutant monitors containing sensors for particulate matter, carbon monoxide, ozone, nitrogen dioxide, and nitrogen monoxide at a reference field site in Baltimore, MD, for 1 year. The first 6 months were used for training multiple regression models, and the second 6 months were used to evaluate the models. The models produced accurate hourly concentrations for all sensors except ozone, which likely requires nonlinear methods to capture peak summer concentrations. The models for all five pollutants produced high Pearson correlation coefficients (r > 0.85), and the hourly averaged calibrated sensor and reference concentrations from the evaluation period were within 3-12%. Each sensor required a distinct set of predictors to achieve the lowest possible root-mean-square error (RMSE). All five sensors responded to environmental factors, and three sensors exhibited cross-sensitives to another air pollutant. We compared the RMSE from models (NO₂, O₃, and NO) that used colocated regulatory instruments and colocated sensors as predictors to address the cross-sensitivities to another gas, and the corresponding model RMSEs for the three gas models were all within 0.5 ppb. This indicates that low-cost sensor networks can yield useable data if the monitoring package is designed to comeasure key predictors. This is key for the utilization of low-cost sensors by diverse audiences since this does not require continual access to regulatory grade instruments.

Development and Performance Evaluation of a Low-Cost Portable PM2.5 Monitor for Mobile Deployment

The concentration of fine particulate matter (PM2.5) is known to vary spatially across a city landscape. Current networks of regulatory air quality monitoring are too sparse to capture these intra-city variations. In this study, we developed a low-cost (60 USD) portable PM2.5 monitor called Smart-P, for use on bicycles, with the goal of mapping street-level variations in PM2.5 concentration. The Smart-P is compact in size (85 × 85 × 42 mm) and light in weight (147 g). Data communication and geolocation are achieved with the cyclist’s smartphone with the help of a user-friendly app. Good agreement was observed between the Smart-P monitors and a regulatory-grade monitor (mean bias error: −3.0 to 1.5 μg m−3 for the four monitors tested) in ambient conditions with relative humidity ranging from 38 to 100%. Monitor performance decreased in humidity > 70% condition. The measurement precision, represented as coefficient of variation, was 6 to 9% in stationary mode and 6% in biking mode across the four tested monitors. Street tests in a city with low background PM2.5 concentrations (8 to 9 μg m−3) and in two cities with high background concentrations (41 to 74 μg m−3) showed that the Smart-P was capable of observing local emission hotspots and that its measurement was not sensitive to bicycle speed. The low-cost and user-friendly nature are two features that make the Smart-P a good choice for empowering citizen scientists to participate in local air quality monitoring.

Intercomparison of PurpleAir Sensor Performance over Three Years Indoors and Outdoors at a Home: Bias, Precision, and Limit of Detection Using an Improved Algorithm for Calculating PM2.5

Low-cost particle sensors are now used worldwide to monitor outdoor air quality. However, they have only been in wide use for a few years. Are they reliable? Does their performance deteriorate over time? Are the algorithms for calculating PM_2.5 concentrations provided by the sensor manufacturers accurate? We investigate these questions using continuous measurements of four PurpleAir monitors (8 sensors) under normal conditions inside and outside a home for 1.5–3 years. A recently developed algorithm (called ALT-CF3) is compared to the two existing algorithms (CF1 and CF_ATM) provided by the Plantower manufacturer of the PMS 5003 sensors used in PurpleAir PA-II monitors. Results. The Plantower CF1 algorithm lost 25–50% of all indoor data due in part to the practice of assigning zero to all concentrations below a threshold. None of these data were lost using the ALT-CF3 algorithm. Approximately 92% of all data showed precision better than 20% using the ALT-CF3 algorithm, but only approximately 45–75% of data achieved that level using the Plantower CF1 algorithm. The limits of detection (LODs) using the ALT-CF3 algorithm were mostly under 1 µg/m³, compared to approximately 3–10 µg/m³ using the Plantower CF1 algorithm. The percentage of observations exceeding the LOD was 53–92% for the ALT-CF3 algorithm, but only 16–44% for the Plantower CF1 algorithm. At the low indoor PM_2.5 concentrations found in many homes, the Plantower algorithms appear poorly suited.

Characterization of Ambient Air Quality in Selected Urban Areas in Uganda Using Low-Cost Sensing and Measurement Technologies

Air pollution is prevalent in cities and urban centers in developing countries including sub-Saharan Africa, but ground monitoring data on local pollution remain inadequate, hindering effective mitigation. We employed low-cost sensing and measurement technologies to quantify pollution levels based on particulate matter (PM_2.5), NO₂, and O₃ over a 6 month period for selected urban centers in three of the four macroregions in Uganda. PM_2.5 diurnal profiles exhibited consistent patterns across all monitoring locations with higher pollution levels manifesting from 18:00 to 00:00 and from 06:00 to 09:00; while the periods from 00:00 to 05:00 and from 09:00 to 17:00 had the lowest levels. Daily PM_2.5 varied widely between 34 and 107 μg/m³ over a 7 day period, well within unhealthy levels (55.5-150.4 μg/m³) for short-term exposure. The inconsistent daily trend are instructive for multiple pollutant assessment to aid specific policy initiatives. The results also show inverse relations between seasonal particulate levels and precipitation, that is, R (correlation coefficient) = -0.93 and -0.62 for Kampala and Wakiso, R = -0.49 and -0.44 for the Eastern region, and R = -0.65 and -0.96 for the Western region. NO₂ monthly concentrations replicated PM_2.5 spatial levels, whereas O₃ exhibited inverse relations probably due to a higher retention time in less-urbanized environments. Both PM_2.5 and NO₂ correlated positively with the resident population. Our findings show significant spatiotemporal variations and exceedances of health guidelines by about 4-6 times across most study locations (with two exceptions) for longer-term exposure. This paper demonstrably highlights the practicability and potential of low-cost approaches for air quality monitoring, with strong prospects for citizen science. This paper also provides novel information regarding air pollution that is needed to improve control strategies for reducing exposures.

Insights about the Sources of PM2.5 in an Urban Area from Measurements of a Low-Cost Sensor Network

PM2.5 measurements using a network of lost-cost sensors were conducted during 2017–2019 in the greater area of Patras, Greece. The average PM2.5 concentration in all sites during the study period was 9.4 μg m−3, varying from 6.2 μg m−3 in the background areas to 12.8 μg m−3 at the city center. The site with the peak PM2.5 levels was not located in an area with high traffic density but rather in a square with pedestrian-only zones and a high restaurant density. The highest PM2.5 concentrations were observed during the colder period (November–March) due to high emissions from residential wood burning for heating purposes. The measurements of the sensors were used to estimate the importance of regional and local PM2.5 sources. During the warm period, regional transport dominated, contributing approximately 80–85% of the PM2.5 in the city center; however, during the colder period, the local sources were responsible for approximately half the PM2.5. The network operated reliably during this multiyear study. Such measurements provide, at a very low cost, valuable insights not only about the temporal and spatial variability of PM2.5 in a city but also about its sources, including the role of regional transport.

Data-Driven Techniques for Low-Cost Sensor Selection and Calibration for the Use Case of Air Quality Monitoring

With the emergence of Low-Cost Sensor (LCS) devices, measuring real-time data on a large scale has become a feasible alternative approach to more costly devices. Over the years, sensor technologies have evolved which has provided the opportunity to have diversity in LCS selection for the same task. However, this diversity in sensor types adds complexity to appropriate sensor selection for monitoring tasks. In addition, LCS devices are often associated with low confidence in terms of sensing accuracy because of the complexities in sensing principles and the interpretation of monitored data. From the data analytics point of view, data quality is a major concern as low-quality data more often leads to low confidence in the monitoring systems. Therefore, any applications on building monitoring systems using LCS devices need to focus on two main techniques: sensor selection and calibration to improve data quality. In this paper, data-driven techniques were presented for sensor calibration techniques. To validate our methodology and techniques, an air quality monitoring case study from the Bradford district, UK, as part of two European Union (EU) funded projects was used. For this case study, the candidate sensors were selected based on the literature and market availability. The candidate sensors were narrowed down into the selected sensors after analysing their consistency. To address data quality issues, four different calibration methods were compared to derive the best-suited calibration method for the LCS devices in our use case system. In the calibration, meteorological parameters temperature and humidity were used in addition to the observed readings. Moreover, we uniquely considered Absolute Humidity (AH) and Relative Humidity (RH) as part of the calibration process. To validate the result of experimentation, the Coefficient of Determination (R²), Root Mean Square Error (RMSE), and Mean Absolute Error (MAE) were compared for both AH and RH. The experimental results showed that calibration with AH has better performance as compared with RH. The experimental results showed the selection and calibration techniques that can be used in designing similar LCS based monitoring systems.

Low-Cost Sensors for Air Quality Monitoring - the Current State of the Technology and a Use Overview

In recent years the monitoring of air quality using cheap sensors has become an interesting alternative to conventional analytical techniques. Apart from vast price differences conventional techniques need to be performed by the trained personnel of commercial or research laboratories. Sensors capable of measuring dust, ozone, nitrogen and sulphur oxides, or other air pollutants are relatively simple electronic devices, which are comparable in size to a mobile phone. They provide the general public with the possibility to monitor air quality which can contribute to various projects that differ in regional scale, commercial funding or community-base. In connection with the low price of sensors arises the question of the quality of measured data. This issue is addressed by a number of studies focused on comparing the sensor data with the data of reference measurements. Sensory measurement is influenced by the monitored analyte, type and design of the particular sensor, as well as by the measurement conditions. Currently sensor networks serve as an additional source of information to the network of air quality monitoring stations, where the density of the network provides concentration trends in the area that may exceed specific measured values of pollutant concentrations and low uncertainty of reference measurements. The constant development of all types of sensors is leading to improvements and the difference in data quality between sensors and conventional monitoring techniques may be reduced.

Establishing A Sustainable Low-Cost Air Quality Monitoring Setup: A Survey of the State-of-the-Art

Low-cost sensors (LCS) are becoming popular for air quality monitoring (AQM). They promise high spatial and temporal resolutions at low-cost. In addition, citizen science applications such as personal exposure monitoring can be implemented effortlessly. However, the reliability of the data is questionable due to various error sources involved in the LCS measurement. Furthermore, sensor performance drift over time is another issue. Hence, the adoption of LCS by regulatory agencies is still evolving. Several studies have been conducted to improve the performance of low-cost sensors. This article summarizes the existing studies on the state-of-the-art of LCS for AQM. We conceptualize a step by step procedure to establish a sustainable AQM setup with LCS that can produce reliable data. The selection of sensors, calibration and evaluation, hardware setup, evaluation metrics and inferences, and end user-specific applications are various stages in the LCS-based AQM setup we propose. We present a critical analysis at every step of the AQM setup to obtain reliable data from the low-cost measurement. Finally, we conclude this study with future scope to improve the availability of air quality data.

Quantify individual variation of real-time PM2.5 exposure in urban Chinese homes based on a novel method

Fine particulate matter (PM_2.5 ) concentrations show high variations in different microenvironments indoors, which has considerable impact on risk management. However, the real-time variations of PM_2.5 exposure associated with per activity/microenvironment and intra-variation among family members remain undefined. In this study, real-time monitors were used to collect real-time PM_2.5 data in different microenvironments in 32 households in urban community of China. Peak concentrations of PM_2.5 were found in kitchen. The parallel levels of PM_2.5 household indoor and outdoor indicated the benefit of clean energies use. To validly assess the health risk of individuals, we proposed a novel method to estimate the real-time exposure of all residents and firstly investigate the intra-variation of PM_2.5 exposure among family members. The member who is responsible for cooking in the family had the maximum PM_2.5 exposure. The ratios among intraindividual variations demonstrated children usually had lower exposure compared to the adults as they stayed more time in lower polluted microenvironments such as living room and bedroom. The exposure intensity in living room was above 1.0 for most residents, indicating it is warranted to alleviate the air pollution in living room. This study firstly focused on the intra differences of PM_2.5 exposure among family members and provided a new insight for indoor air pollution management. The results suggested when adopting measures to reduce exposure, the microenvironments pattern of each member should be taken into consideration. Future work is welcomed to move another big step on this issue to protect the human health.

Publicly available low-cost sensor measurements for PM2.5 exposure modeling: Guidance for monitor deployment and data selection

High-resolution, high-quality exposure modeling is critical for assessing the health effects of ambient PM_2.5 in epidemiological studies. Using sparse regulatory PM_2.5 measurements as principal model inputs may result in two issues in exposure prediction: (1) they may affect the models' accuracy in predicting PM_2.5 spatial distribution; (2) the internal validation based on these measurements may not reliably reflect the model performance at locations of interest (e.g., a cohort's residential locations). In this study, we used the PM_2.5 measurements from a publicly available commercial low-cost PM_2.5 network, PurpleAir, with an external validation dataset at the residential locations of a representative sample of participants from the Adult Changes in Thought - Air Pollution (ACT-AP) study, to improve the accuracy of exposure prediction at the cohort participant locations. We also proposed a metric based on principal component analysis (PCA) - the PCA distance - to assess the similarity between monitor and cohort locations to guide monitor deployment and data selection. The analysis was based on a spatiotemporal modeling framework with 51 "gold-standard" monitors and 58 PurpleAir monitors for model development, as well as 105 home monitors at the cohort locations for model validation, in the Puget Sound region of Washington State from June 2017 to March 2019. After including calibrated PurpleAir measurements as part of the dependent variable, the external spatiotemporal validation R² and root-mean-square error, RMSE, for two-week concentration averages improved from 0.84 and 2.22 μg/m³ to 0.92 and 1.63 μg/m³, respectively. The external spatial validation R² and RMSE for long-term averages over the modeling period improved from 0.72 and 1.01 μg/m³ to 0.79 and 0.88 μg/m³, respectively. The exposure predictions incorporating PurpleAir measurements demonstrated sharper urban-suburban concentration gradients. The PurpleAir monitors with shorter PCA distances improved the model's prediction accuracy more substantially than the monitors with longer PCA distances, supporting the use of this similarity metric.

Exposure assessment of PM2.5 using smart spatial interpolation on regulatory air quality stations with clustering of densely-deployed microsensors

Accurate mapping of air pollutants is essential for epidemiological studies and environmental risk assessments. Concentrations measured by air quality monitoring stations (AQMS) have primarily been used to assess the exposure of PM_2.5. However, the low coverage and amount of monitoring stations affect the errors of spatial interpolation or geostatistical estimates. In contrast to other integrated approaches developed for improved air pollution estimates, this study utilizes data from low-cost microsensors densely deployed in Taiwan to improve the popular spatial interpolation approach called inverse distance weighting (IDW). A large dataset from thousands of low-cost sensors could improve spatial interpolation by describing the distribution of PM_2.5 in detail. Therefore, this study presents a clustering-based method to assess the distribution of PM_2.5. Then, a smarter IDW is performed based on correlated observations from the selected air quality stations. The publicly available data chosen for this investigation pertained to Taiwan, which has deployed 74 monitoring stations and more than 11,000 low-cost sensors since December 2020. The results of leave-one-out cross-validation indicate that there are fewer PM_2.5 estimation errors in the developed approach than in estimations that use kriging across almost all of the months and sampled dates of 2019 and 2020, particularly those with higher PM_2.5 spatial heterogeneities. Spatial heterogeneities could result in more significant estimation errors in mainstream approaches. The root mean square error of the monthly average estimate for PM_2.5 ranged from 1.17 to 3.86 μg/m³. We also found that the clustering of one month characterizing the pattern of PM_2.5 distribution could perform well in spatial interpolations based on historical data from monitoring stations. According to the information on the openaq platform, low-cost sensors are in demand in cities and areas. This trend might pave the way for the application of the proposed approach in other areas for superior exposure assessments.

Design and Testing of a Low-Cost Sensor and Sampling Platform for Indoor Air Quality

Americans spend most of their time indoors at home, but comprehensive characterization of in-home air pollution is limited by the cost and size of reference-quality monitors. We assembled small "Home Health Boxes" (HHBs) to measure indoor PM2.5, PM10, CO2, CO, NO2, and O3 concentrations using filter samplers and low-cost sensors. Nine HHBs were collocated with reference monitors in the kitchen of an occupied home in Fort Collins, Colorado, USA for 168 h while wildfire smoke impacted local air quality. When HHB data were interpreted using gas sensor manufacturers' calibrations, HHBs and reference monitors (a) categorized the level of each gaseous pollutant similarly (as either low, elevated, or high relative to air quality standards) and (b) both indicated that gas cooking burners were the dominant source of CO and NO2 pollution; however, HHB and reference O3 data were not correlated. When HHB gas sensor data were interpreted using linear mixed calibration models derived via collocation with reference monitors, root-mean-square error decreased for CO2 (from 408 to 58 ppm), CO (645 to 572 ppb), NO2 (22 to 14 ppb), and O3 (21 to 7 ppb); additionally, correlation between HHB and reference O3 data improved (Pearson's r increased from 0.02 to 0.75). Mean 168-h PM2.5 and PM10 concentrations derived from nine filter samples were 19.4 μg m-3 (6.1% relative standard deviation [RSD]) and 40.1 μg m-3 (7.6% RSD). The 168-h PM2.5 concentration was overestimated by PMS5003 sensors (median sensor/filter ratio = 1.7) and underestimated slightly by SPS30 sensors (median sensor/filter ratio = 0.91).

Probabilistic Machine Learning with Low-Cost Sensor Networks for Occupational Exposure Assessment and Industrial Hygiene Decision Making

Occupational exposure assessments are dominated by small sample sizes and low spatial and temporal resolution with a focus on conducting Occupational Safety and Health Administration regulatory compliance sampling. However, this style of exposure assessment is likely to underestimate true exposures and their variability in sampled areas, and entirely fail to characterize exposures in unsampled areas. The American Industrial Hygiene Association (AIHA) has developed a more realistic system of exposure ratings based on estimating the 95th percentiles of the exposures that can be used to better represent exposure uncertainty and exposure variability for decision-making; however, the ratings can still fail to capture realistic exposure with small sample sizes. Therefore, low-cost sensor networks consisting of numerous lower-quality sensors have been used to measure occupational exposures at a high spatiotemporal scale. However, the sensors must be calibrated in the laboratory or field to a reference standard. Using data from carbon monoxide (CO) sensors deployed in a heavy equipment manufacturing facility for eight months from August 2017 to March 2018, we demonstrate that machine learning with probabilistic gradient boosted decision trees (GBDT) can model raw sensor readings to reference data highly accurately, entirely removing the need for laboratory calibration. Further, we indicate how the machine learning models can produce probabilistic hazard maps of the manufacturing floor, creating a visual tool for assessing facility-wide exposures. Additionally, the ability to have a fully modeled prediction distribution for each measurement enables the use of the AIHA exposure ratings, which provide an enhanced industrial decision-making framework as opposed to simply determining if a small number of measurements were above or below a pertinent occupational exposure limit. Lastly, we show how a probabilistic modeling exposure assessment with high spatiotemporal resolution data can prevent exposure misclassifications associated with traditional models that rely exclusively on mean or point predictions.

Room HVAC Influences on the Removal of Airborne Particulate Matter: Implications for School Reopening during the COVID-19 Pandemic

(1) Background: Many schools and higher education settings have confronted the issue of reopening their facilities after the COVID-19 pandemic. In response, several airflow strategies spanning from adding portable air purifiers to major mechanical overhauls have been suggested to equip classrooms with what is necessary to provide a safe and reliable environment. Yet, there are many unknowns about specific contributions of the building system and its design and performance on indoor air quality (IAQ) improvements. (2) Methods: this study examined the combined effect of ventilation type, airflow rates, and filtration on IAQ in five different classrooms. Experiments were conducted by releasing inert surrogate particles into the classrooms and measuring the concentrations in various locations of the room. (3) Results: we showed that while the distribution of particles in the space is a complex function of space geometry and air distribution configurations, the average decay rate of contaminants is proportional to the number of air changes per hour in the room. (4) Conclusions: rooms with a central HVAC system responded quicker to an internal source of contamination than rooms with only fan coil units. Furthermore, increasing the ventilation rate without improved filtration is an inefficient use of energy.

An accessible method for screening aerosol filtration identifies poor-performing commercial masks and respirators

BACKGROUND

The COVID-19 pandemic has presented an acute shortage of regulation-tested masks. Many of the alternatives available to hospitals have not been certified, leaving uncertainty about their ability to properly protect healthcare workers from SARS-CoV-2 transmission.

OBJECTIVE

For situations where regulatory methods are not accessible, we present experimental methods to evaluate mask filtration and breathability quickly via cost-effective approaches (e.g., ~$2000 USD) that could be replicated in communities of need without extensive infrastructure. We demonstrate the need for screening by evaluating an existing diverse inventory of masks/respirators from a local hospital.

METHODS

Two experimental approaches are presented to examine both aerosol filtration and flow impedance (i.e., breathability). For one of the approaches ("quick assessment"), screening for appropriate filtration could be performed under 10 min per mask, on average. Mask fit tests were conducted in tandem but are not the focus of this study.

RESULTS

Tests conducted of 47 nonregulation masks reveal variable performance. A number of commercially available masks in hospital inventories perform similarly to N95 masks for aerosol filtration of 0.2 μm and above, but there is a range of masks with relatively lower filtration efficiencies (e.g., <90%) and a subset with poorer filtration (e.g., <70%). All masks functioned acceptably for breathability, and impedance was not correlated with filtration efficiency.

SIGNIFICANCE

With simplified tests, organizations with mask/respirator shortages and uncertain inventories can make informed decisions about use and procurement.

Performance and Deployment of Low-Cost Particle Sensor Units to Monitor Biomass Burning Events and Their Application in an Educational Initiative

Biomass burning smoke is often a significant source of airborne fine particles in regional areas where air quality monitoring is scarce. Emerging sensor technology provides opportunities to monitor air quality on a much larger geographical scale with much finer spatial resolution. It can also engage communities in the conversation around local pollution sources. The SMoke Observation Gadget (SMOG), a unit with a Plantower dust sensor PMS3003, was designed as part of a school-based Science, Technology, Engineering and Mathematics (STEM) project looking at smoke impacts in regional areas of Victoria, Australia. A smoke-specific calibration curve between the SMOG units and a standard regulatory instrument was developed using an hourly data set collected during a peat fire. The calibration curve was applied to the SMOG units during all field-based validation measurements at several locations and during different seasons. The results showed strong associations between individual SMOG units for PM2.5 concentrations (r2 = 0.93-0.99) and good accuracy (mean absolute error (MAE) < 2 μg m-3). Correlations of the SMOG units to reference instruments also demonstrated strong associations (r2 = 0.87-95) and good accuracy (MAE of 2.5-3.0 μg m-3). The PM2.5 concentrations tracked by the SMOG units had a similar response time as those measured by collocated reference instruments. Overall, the study has shown that the SMOG units provide relevant information about ambient PM2.5 concentrations in an airshed impacted predominantly by biomass burning, provided that an adequate adjustment factor is applied.

Toward Clean Residential Energy: Challenges and Priorities in Research

Solid fuels used for cooking, heating, and lighting are major emission sources of many air pollutants, specifically PM_2.5 and black carbon, resulting in adverse environmental and health impacts. At the same time, the transition from using residential solid fuels toward using cleaner energy sources can result in significant health benefits. Here, we briefly review recent research progress on the emissions of air pollutants from the residential sector and the impacts of emissions on ambient and indoor air quality, population exposure, and health consequences. The major challenges and future research priorities are identified and discussed.