Advanced oxidation process-mediated removal of pharmaceuticals from water: A review

Degradation behaviors of Nabumetone and its metabolite during UV/monochloramine process: Experimental and theoretical study

This study investigated degradation behaviors of a nonsteroidal anti-inflammatory drug Nabumetone (NMT) and its major metabolite 6-methoxy-2-naphthylacetic acid (MNA) in the coupling process of ultraviolet and monochloramine (UV/NH2Cl). The second-order rate constants of the contaminants reacting with reactive radicals (HO•, Cl•, Cl2•⁻, and CO3•⁻) were determined by laser flash photolysis experiments. HO• and Cl• contributed predominantly with 52.3% and 21.7% for NMT degradation and 60.8% and 22.3% for MNA degradation. The presence of chlorides retarded the degradation of NMT, while promoted the destruction of MNA, which was ascribed to the photosensitization effects of MNA under UV irradiation. Density functional theory (DFT) calculations revealed that radical adduct formation (RAF) was dominant pathway for both HO• and Cl• reacting with the contaminants, and hydrogen atom transfer (HAT) preferred to occur on side chains of NMT and MNA. NMT reacted with NO2• through single electron transfer (SET) with the second-order rate constant calculated to be 5.35 × 107 (mol/L)-1 sec-1, and the contribution of NO2• was predicted to be 13.0% of the total rate constant of NMT in pure water, which indicated that NO2• played a non-negligible role in the degradation of NMT. The acute toxicity and developmental toxicity of NMT were enhanced after UV/NH2Cl treatment, while those of MNA were alleviated. The transformation products of both NMT and MNA exhibited higher mutagenicity than their parent compounds. This study provides a deep understanding of the mechanism of radical degradation of NMT and MNA in the treatment of UV/NH2Cl.

Theoretical insights, degradation, and sub-lethal toxicity of thiamethoxam to the planarian Girardia tigrina

Advanced oxidative processes, such as Photo-Fenton, transform organic contaminants due to the attack by radicals. In this context, the lethal and sub-lethal effects of the Cruiser® 350FS (CRZ) with the active ingredient thiamethoxam (TMX) were investigated using the planarian Girardia tigrina. Degradation of thiamethoxam by the Fenton process was also assessed by using theoretical studies and the efficiency of Solar-Fenton versus Fenton. The 48 h LC50 value of CRZ for planarians was 478.6 mg L-1. The regeneration of planarians was significantly affected for concentrations ≥ 17 mg·L-1 of TMX (24 h). The Solar-Fenton showed a high degradation percentage reaching ~70%. The theoretical model showed the atoms of the TMX molecule that will suffer attacks from the formed radicals. Current results open new perspectives concerning the treatment of TMX in the aquatic environment because the 70% degradation seems to be sufficient to reach concentrations that do not induce sub-lethal effects in planarians. Further studies should determine if the by-products generated might be toxic for planaria or other organisms.

Effects of TiO2 Nanoparticles Synthesized via Microwave Assistance on Adsorption and Photocatalytic Degradation of Ciprofloxacin

In this study, the optimal microwave-assisted sol-gel synthesis parameters for achieving TiO2 nanoparticles with the highest specific surface area and photocatalytic activity were determined. Titanium isopropoxide was used as a precursor to prepare the sol (colloidal solution) of TiO2. Isopropanol was used as a solvent; acetylacetone was used as a complexation moderator; and nitric acid was used as a catalyst. Four samples of titanium dioxide were synthesized from the prepared colloidal solution in a microwave reactor at a temperature of 150 °C for 30 min and at a temperature of 200 °C for 10, 20, and 30 min. The phase composition of the TiO2 samples was determined by X-ray diffraction analysis (XRD) and Fourier-transform infrared spectroscopy (FTIR). Nitrogen adsorption/desorption isotherms were used to determine the specific surface area and pore size distributions using the Brunauer-Emmett-Teller (BET) method. The band-gap energy values of the TiO2 samples were determined by diffuse reflectance spectroscopy (DRS). The distribution of Ti and O in the TiO2 samples was determined by SEM-EDS analysis. The effects of adsorption and photocatalytic activity of the prepared TiO2 samples were evaluated by the degradation of ciprofloxacin (CIP) as an emerging organic pollutant (EOP) under UV-A light (365 nm). The results of the photocatalytic activity of the synthesized TiO2 nanoparticles were compared to the benchmark Degussa P25 TiO2. Kinetic parameters of adsorption and photocatalysis were determined and analyzed. It was found that crystalline TiO2 nanoparticles with the highest specific surface area, the lowest energy band gap, and the highest photocatalytic degradation were the samples synthesized at 200 °C for 10 min. The results indicate that CIP degradation by all TiO2 samples prepared at 200 °C show a synergistic effect of adsorption and photocatalytic degradation in the removal process.

Ecological impact of pharmaceutical pollutants and options of river health improvements - A risk analysis-based approach

Pharmaceuticals are one of the emerging pollutants (EPs) in river waters across the world. Due to their toxic effects on aquatic organisms, they have drawn the global attention of the scientific community concerned with river ecosystems. This paper reviews the existing occurrence data for various pharmaceutical pollutants (PPs) reported in river waters in some part of the world and their ecological impacts. Using algae, macroinvertebrates (MI), and fish as biotic indicator groups in water to reflect river health conditions, an attempt has been made to assess the ecological risk due to the presence of PPs in the water environment. After ascertaining the predicted no-effect concentration (PNEC) of PPs for selected groups of aquatic organisms, the risk quotient (RQ) is estimated based on their measured environmental concentration (MEC). When MEC > PNEC and RQ > 1 for any of the biotic indicator, ecologically it is 'high risk' condition. The determination of PNEC uses a minimum assessment factor (AF) of 10 due to uncertainty in data over the no observed effect level (NOEL) or lowest observed effect level (LOEL). Accordingly, MEC 10 times higher than PNEC, (RQ = 10) represents a threshold risk concentration (RCT) beyond which adverse effects may start showing observable manifestations. In the present study, a new classification system of 'high risk' conditions for RQ = 1-10 has been proposed, starting from 'moderately high' to 'severely high'. For RQ > 10, the ecological condition of the river is considered 'impaired'. For river health assessment, in the present study, the whole range of physico-chemical characteristics of river water quality has been divided into three groups based on their ease of measurement and frequency of monitoring. Dissolved oxygen related parameters (DORPs), nutrients (NTs), and EPs. PPs represent EPs in this study. A framework for calculating separate indicator group score (IGS) and the overall river health index (RHI) has been developed to predict indicator group condition (IGC) and river health condition (RHC), respectively. Color-coded hexagonal pictorial forms representing IGC and RHC provide a direct visible perception of the existing aquatic environment and a scientific basis for prioritization of corrective measures in terms of treatment technology selection for river health improvements. The analyses indicate that many rivers across the world are under 'high risk' conditions due to PPs having MEC > PNEC and RQ > 1. Up to RCT, (where RQ = 10), the 'high risk' condition varies from 'moderately high' to 'severely high'. In many instances, RQ is found much more higher than 10, indicating that the ecological condition of river may be considered as 'impaired'. Algae is the most frequently affected group of biotic indicators, followed by MI and fish. A review of treatment methods for selection of appropriate technology to reduce the pollution load, especially PPs from the wastewater streams has been summarized. It appears that constructed wetlands (CWs) are at present the most suitable nature-based solutions, particularly for the developing economies of the world, to reduce the concentrations of PPs within limits to minimize the ecological impacts of pharmaceutical compounds on biotic indicators and restore the river health condition. Some suggestive design guidelines for the CWs have also been presented to initiate the process.

Epoxiconazole degradation in water samples: a comparative study of Fenton, photo-Fenton, solar photo-Fenton, and solar photolysis processes

Epoxiconazole (EPO) is classified as a persistent organic pollutant due to its ability to persist in the environment for prolonged periods. Its degradation is pivotal in mitigating its environmental impact. This investigation focuses on assessing the degradation of EPO using various methodologies, namely Fenton, photo-Fenton, solar photo-Fenton, and solar photolysis, conducted in both Milli-Q water and groundwater. These experiments encompassed evaluations at both the standard pH typically used in photo-Fenton reactions and the natural pH levels inherent to the respective aqueous environments. Additionally, EPO degradation products were analyzed after a 60-min reaction. Notably, in systems utilizing groundwater, the inclusion of additional iron was unnecessary, as the naturally occurring iron content in the groundwater facilitated the intended processes. Specifically, in Milli-Q water, solar photo-Fenton demonstrated an EPO degradation efficiency of 97%. Furthermore, the substitution of Milli-Q water with groundwater in Fenton-like processes did not significantly affect the efficacy of EPO degradation. These findings underscore the potential of solar photo-Fenton as an economically viable and environmentally sustainable strategy for EPO degradation.

Research Progress on the Degradation of Organic Pollutants in Wastewater via Ultrasound/Periodate Systems: A Review

In recent years, the efficient removal of organic pollutants from wastewater has emerged as a critical area of global research interest. Against this backdrop, an array of innovative technologies for wastewater treatment has been developed. Among numerous advanced oxidation processes (AOPs), periodate (PI), an emerging oxidizing agent in AOPs, has garnered significant attention from researchers. Particularly, the integration of ultrasound (US)-activated PI systems has been recognized as an exceptionally promising approach for the synergistic degradation of organic pollutants in wastewater. In this paper, we conducted a thorough analysis of the mechanisms underlying the degradation of organic pollutants using the US/PI system. Furthermore, we comprehensively delineated the effects of ultrasonic power, periodate concentration, temperature, pH, coexisting inorganic ions, and dissolved organic matter on the removal efficiency of organic pollutants and summarized application cases of the US/PI system for the degradation of different pollutants. Finally, we also offered prospective discussions on the future trajectories of US/PI technology development.

Tackling Losartan Contamination: The Promise of Peroxymonosulfate/Fe(II) Advanced Oxidation Processes

Losartan, an angiotensin II receptor antagonist frequently detected in wastewater effluents, poses considerable risks to both aquatic ecosystems and human health. Seeking to address this challenge, advanced oxidation processes (AOPs) emerge as robust methodologies for the efficient elimination of such contaminants. In this study, the degradation of Losartan was investigated in the presence of activated peroxymonosulfate (PMS), leveraging ferrous iron as a catalyst to enhance the oxidation process. Utilizing advanced analytical techniques such as NMR and mass spectrometry, nine distinct byproducts were characterized. Notably, seven of these byproducts were identified for the first time, providing novel insights into the degradation pathway of Losartan. The study delved into the kinetics of the degradation process, assessing the degradation efficiency attained when employing the catalyst alone versus when using it in combination with PMS. The results revealed that Losartan degradation reached a significant level of 64%, underscoring the efficacy of PMS/Fe(II) AOP techniques as promising strategies for the removal of Losartan from water systems. This research not only enriches our understanding of pollutant degradation mechanisms, but also paves the way for the development of sustainable water treatment technologies, specifically targeting the removal of pharmaceutical contaminants from aquatic environments.

Role of biochar in superoxide-dominated dye degradation in catalyst-activated peroxymonosulphate process

In recent times, the application of biochar (BC) as an upcoming catalyst for the elimination of recalcitrant pollutants has been widely explored. Here, an iron loaded bamboo biochar activated peroxymonosulphate (PMS) process was tested for removing Congo red (CR) dye from water medium. The catalyst was synthesized using a green synthesis method using neem extracts and characterized using SEM, FTIR, and XRD. The effects of various operating parameters, including solution pH, catalyst dosage, and pollutant dosage, on dye degradation efficiency were examined. The results showed that at the optimized conditions of 300 mg L-1 PMS concentration, 200 mg L-1 catalyst dosage, and pH 6, about 89.7% of CR dye (initial concentration 10 ppm) was removed at 60 min of operation. Scavenging experiments revealed the significant contribution of O2•-, •OH, and 1O2 for dye degradation, with a major contribution of O2•-. The activation of PMS was mainly done by biochar rather than iron (loaded on biochar). The catalyst was highly active even after four cycles.

Sustainable bioelectric activation of periodate for highly efficient micropollutant abatement

The periodate (PI)-based advanced oxidation process is valued for environmental remediation, but current activation methods involve high costs, secondary contamination risks, and limited applicability due to external energy inputs (e.g., UV), catalyst incorporation (e.g., Fe2+), or environmental modifications (e.g., freezing). In this work, novel bioelectric activation of PI using the electrons generated by electroactive bacteria was developed and investigated for rapid removal of carbamazepine (CBZ), achieving 100 %, 100 %, and 76 % removal efficiency for 4.22 µM of CBZ in 20 min at pH 2, 120 min at pH 6.4, and HRT of 30 min at pH 8.5, respectively, with a 1 mM PI dose and without an input voltage. It was deduced that electrons derived from bacteria could directly activate PI using Ti mesh electrodes and generate •IO3 via single electron transfer under strongly acidic conditions (e.g., pH 2). Nevertheless, under weak alkaline conditions (e.g., pH 8.5), biogenic electrons indirectly activated PI by generating OH-via 4e-reduction at the Ti mesh cathode, resulting in the formation of •O2- and 1O2. In addition to the metal cathode, a carbon-based cathode finely modulates the 2e-reduction, yielding H2O2 and activating PI to mainly form •OH. Moreover, primarily non-toxic IO3- was produced during treatment, while no detectable reactive iodine species (HOI, I2, and I3-) were observed. Furthermore, the bioelectric activation of PI demonstrated its capability to remove various micropollutants present in secondary-treated municipal wastewater, showcasing its broad-spectrum degradation ability. This study introduces a novel, cost-effective, and environmentally friendly PI activation technique with promising applicability for micropollutant elimination in water treatment.

Enhanced Heterogeneous Fenton Degradation of Organic Dyes by Bimetallic Zirconia-Based Catalysts

The qualitative impact of pollutants on water quality is mainly related to their nature and their concentration, but in any case, they determine a strong impact on the involved ecosystems. In particular, refractory organic compounds represent a critical challenge, and several degradation processes have been studied and developed for their removal. Among them, heterogeneous Fenton treatment is a promising technology for wastewater and liquid waste remediation. Here, we have developed mono- and bimetallic formulations based on Co, Cu, Fe, and Mn, which were investigated for the degradation of three model organic dyes (methylene blue, rhodamine B, and malachite green). The treated samples were then analyzed by means of UV-vis spectrophotometry techniques. Bimetallic iron-based materials achieved almost complete degradation of all three model molecules in very short time. The Mn-Fe catalyst resulted in the best formulation with an almost complete degradation of methylene blue and malachite green at pH 5 in 5 min and of rhodamine B at pH 3 in 30 min. The results suggest that these formulations can be applied for the treatment of a broad range of liquid wastes comprising complex and variable organic pollutants. The investigated catalysts are extremely promising when compared to other systems reported in the literature.

UV/TiO2 photocatalysis as post-treatment of anaerobic membrane bioreactor effluent for reuse

Advanced oxidation processes have been widely applied as a post-treatment solution to remove residual organic compounds in water reuse schemes. However, UV/TiO2 photocatalysis, which provides a sustainable option with no continuous chemical addition, has very rarely been studied to treat anaerobically treated effluents. In the current study, the removal of organics and nutrients from an anaerobic membrane bioreactor (AnMBR) effluent is evaluated during adsorption and photocatalysis processes under various conditions of TiO2 dose and UV intensity and compared to the effluent from an aerobic membrane bioreactor (AeMBR). The sequence for preferential adsorption on TiO2 was found to be phosphorus, inorganic carbon and then ammonia/organic carbon were found. The competing effect between the organics and nutrients, along with the low UV transmission efficiency caused by the need for high doses of TiO2, ultimately compromise the organic removal efficiency in the AnMBR permeate. TiO2 dosage was found to have a greater impact than UV intensity on improving the overall removal performance as nutrients are competing for the adsorption site but are not photodegraded. Under the same operational condition, the UV/TiO2 photocatalysis displayed a higher removal efficiency of organic matter and phosphorus in the AeMBR effluent due to a lower initial organics concentration and absence of ammonia as compared to the AnMBR effluent.

Advanced degradation of organic pollutants using sonophotocatalytic peroxymonosulfate activation with CoFe2O4/Cu- and Ce-doped SnO2 composites

The rampant upsurge of organic pollutants in aqueous media has become one of the major concerns nowadays. Finding non-specific catalysts that can target a wide range of organic pollutants is a key challenge. Eco-friendly oxidative radicals, such as promoted by peroxymonosulfate (PMS), are necessary for efficient water decontamination. We propose a multicomponent composite catalyst for activating PMS using a dual strategy of sonophotocatalysis. The composite integrates cobalt ferrite and Cu- or Ce-doped SnO2, with the at. % of doping metal and the mixture ratio carefully balanced. The top-performing architectures were able to decompose rhodamine B (20 ppm), a representative pollutant, in under 3 min and achieve over 70% mineralization in just 5 min. The synthesized nanocomposites demonstrated exceptional sonophotocatalytic performance, even when treating complex and diverse multipollutant solutions (80 ppm), achieving over 75% mineralization after 150 min. Considering their high stability and reusability, the proposed CoFe2O4/Cu- and Ce-doped SnO2 materials are among the state-of-the-art heterogeneous catalysts for mineralizing organic pollutants through PMS activation.

An insight into the role of experimental parameters in advanced oxidation process applied for pharmaceutical degradation

The advanced oxidation process (AOP) is an efficient method to treat recalcitrance pollutants such as pharmaceutical compounds. The essential physicochemical factors in AOP experiments significantly influence the efficiency, speed, cost, and safety of byproducts of the treatment process. In this review, we collected recent articles that investigated the elimination of pharmaceutical compounds by various AOP systems in a water medium, and then we provide an overview of AOP systems, the formation mechanisms of active radicals or reactive oxygen species (ROS), and their detection methods. Then, we discussed the role of the main physicochemical parameters (pH, chemical interference, temperature, catalyst, pollutant concentration, and oxidant concentration) in a critical way. We gained insight into the most frequent scenarios for the proper and improper physicochemical parameters for the degradation of pharmaceutical compounds. Also, we mentioned the main factors that restrict the application of AOP systems in a commercial way. We demonstrated that a proper adjustment of AOP experimental parameters resulted in promoting the treatment performance, decreasing the treatment cost and the treatment operation time, increasing the safeness of the system products, and improving the reaction stoichiometric efficiency. The outcomes of this review will be beneficial for future AOP applicants to improve the pharmaceutical compound treatment by providing a deeper understanding of the role of the parameters. In addition, the proper application of physicochemical parameters in AOP systems acts to track the sustainable development goals (SDGs).

An Overview of Degradation Strategies for Amitriptyline

Antidepressant drugs play a crucial role in the treatment of mental health disorders, but their efficacy and safety can be compromised by drug degradation. Recent reports point to several drugs found in concentrations ranging from the limit of detection (LOD) to hundreds of ng/L in wastewater plants around the globe; hence, antidepressants can be considered emerging pollutants with potential consequences for human health and wellbeing. Understanding and implementing effective degradation strategies are essential not only to ensure the stability and potency of these medications but also for their safe disposal in line with current environment remediation goals. This review provides an overview of degradation pathways for amitriptyline, a typical tricyclic antidepressant drug, by exploring chemical routes such as oxidation, hydrolysis, and photodegradation. Connex issues such as stability-enhancing approaches through formulation and packaging considerations, regulatory guidelines, and quality control measures are also briefly noted. Specific case studies of amitriptyline degradation pathways forecast the future perspectives and challenges in this field, helping researchers and pharmaceutical manufacturers to provide guidelines for the most effective degradation pathways employed for minimal environmental impact.

A Comprehensive Review on Modification of Titanium Dioxide-Based Catalysts in Advanced Oxidation Processes for Water Treatment

It has become necessary to develop effective strategies to prevent and reduce water pollution as a result of the increase in dangerous pollutants in water reservoirs. Consequently, there is a need to design new catalyst materials to promote the efficiency of advanced oxidation processes (AOPs) in the field of wastewater treatment plant to ensure the mineralization of trace organic contaminants. A notable approach gaining attention involves the coupling of sulfate radicals-based AOPs to photocatalysis or electrocatalysis processes, aiming to achieve the complete removal of refractory contaminants into water and carbon dioxide. Titanium dioxide as metal oxide has received great attention for its catalytic application in water purification. TiO2 catalysts offer a multitude of advantages in AOPs. They are characterized by their high photocatalytic activity under both ultraviolet and visible light, making them environmentally friendly due to the absence of toxic byproducts during oxidation. Their versatility is remarkable, finding utility in various AOPs, from photocatalysis to photo-Fenton processes. TiO2's durability ensures long-lasting catalytic activity, which is crucial for continuous treatment processes, and their cost-effectiveness is particularly advantageous. Furthermore, their chemical stability allows it to withstand varying pH conditions. However, the large band gap energy and low electrical conductivity hinder the catalytic reaction effectiveness. This review aims to examine various approaches to enhance the catalytic performance of titanium dioxide, with the objective of enabling more efficient water purification methods.

The performance of pharmaceutical wastewater treatment system of electrocoagulation assisted adsorption using perforated electrodes to reduce passivation

The integrated electrocoagulation-assisted adsorption (ECA) system with a solar photovoltaic power supply has gained more attention as an effective approach for reduction chemical oxygen demand (COD) from pharmaceutical wastewater (PhWW). In this research, the ECA system was used for the treatment of PhWW. Several operating parameters were investigated, including electrode number, configuration, distance, operating time, current density, adsorption time, and temperature. A current density of 6.656 mA/cm2, six electrodes, a 20-min time, a 4 cm distance, an MP-P configuration, and a 45 °C temperature produced the maximum COD reductions, where the operating cost of conventional energy was 0.273 $/m3. The EC, adsorption, and combination of EC and adsorption processes achieved efficient COD reductions of 85.4, 69.1, and 95.5%, respectively. The pseudo-second-order kinetic model and the Freundlich isotherm fit the data of the endothermic adsorption process. Therefore, it was found that the combination processes were superior to the use of these processes in isolation to remove COD.

Removal characteristics of 53 micropollutants during ozonation, chlorination, and UV/H2O2 processes used in drinking water treatment plant

The removal of 53 emerging micropollutants (MPs), including 10 per- and polyfluorinated substances (PFASs), 25 pharmaceuticals and personal care products (PPCPs), 7 pesticides, 5 endocrine disrupters (EDCs), 3 nitrosamines, and 3 taste and odor compounds (T&Os), by chlorination, ozonation, and UV/H2O2 treatment was examined in deionized water and surface waters used as the raw waters in drinking water treatment plants (DWTPs) in South Korea. The UV/H2O2 treatment was effective in the removal of most MPs, whereas chlorination was selectively effective for 19 MPs, including EDCs (>70 %). MPs containing aromatic ring with electron-donating functional group, or primary and secondary amines were effectively removed by chlorination immediately upon reaction initiation. The removal of MPs by ozonation was generally lower than that of the other two processes at a low ozone dose (1 mg L-1), but higher than chlorination at a high ozone dose (3 mg L-1), particularly for 16 MPs, including T&Os. Compared in deionized water, the removals of MPs in the raw water samples were lower in all three processes. The regression models predicting the rate constants (kobs) of 53 MPs showed good agreement between modeled and measured value for UV/H2O2 treatment (R2 = 0.948) and chlorination (R2 = 0.973), despite using only dissolved organic carbon (DOC) and oxidant concentration as variables, whereas the ozonation model showed a variation (R2 = 0.943). Our results can provide the resources for determining which oxidative process is suitable for treating specific MPs present in the raw waters of DWTPs.

Advanced oxidation and biological integrated processes for pharmaceutical wastewater treatment: A review

The stress of pharmaceutical and personal care products (PPCPs) discharging to water bodies and the environment due to increased industrialization has reduced the availability of clean water. This poses a potential health hazard to animals and human life because water contamination is a great issue to the climate, plants, humans, and aquatic habitats. Pharmaceutical compounds are quantified in concentrations ranging from ng/Lto μg/L in aquatic environments worldwide. According to (Alsubih et al., 2022), the concentrations of carbamazepine, sulfamethoxazole, Lutvastatin, ciprofloxacin, and lorazepam were 616-906 ng/L, 16,532-21635 ng/L, 694-2068 ng/L, 734-1178 ng/L, and 2742-3775 ng/L respectively. Protecting and preserving our environment must be well-driven by all sectors to sustain development. Various methods have been utilized to eliminate the emerging pollutants, such as adsorption and biological and advanced oxidation processes. These methods have their benefits and drawbacks in the removal of pharmaceuticals. Successful wastewater treatment can save the water bodies; integrating green initiatives into the main purposes of actor firms, combined with continually periodic awareness of the current and potential implications of environmental/water pollution, will play a major role in water conservation. This article reviews key publications on the adsorption, biological, and advanced oxidation processes used to remove pharmaceutical products from the aquatic environment. It also sheds light on the pharmaceutical adsorption capability of adsorption, biological and advanced oxidation methods, and their efficacy in pharmaceutical concentration removal. A research gap has been identified for researchers to explore in order to eliminate the problem associated with pharmaceutical wastes. Therefore, future study should focus on combining advanced oxidation and adsorption processes for an excellent way to eliminate pharmaceutical products, even at low concentrations. Biological processes should focus on ideal circumstances and microbial processes that enable the simultaneous removal of pharmaceutical compounds and the effects of diverse environments on removal efficiency.

Evaluation of different functionalization methodologies for improving the removal of three target antibiotics from wastewater by a brewery waste activated carbon

This work aims to increase the efficiency of an activated carbon produced from brewery waste (AC) in the removal of three target antibiotics (sulfamethoxazole (SMX), trimethoprim (TMP), and ciprofloxacin (CIP)) by surface incorporation of oxygen, nitrogen or sulfur groups. AC was produced using spent brewery grains (the most abundant waste from the brewing industry) as raw material, K2CO3 as activating agent and microwave energy for pyrolysis. Then, seven different functionalized AC were prepared, characterized for their physicochemical properties, and tested for adsorption (%) of SMX, TMP and CIP from three different matrices (ultrapure water (pH ~5-6), buffered ultrapure water (pH 8), and effluent from a municipal wastewater treatment plant (WWTP effluent (pH 8)), under batch operation. Based on the obtained results, an oxygen functionalized AC was selected for further characterization and studies on the adsorption of the target antibiotics from the WWTP effluent. Kinetic results fitted the pseudo-second order model and the equilibrium isotherms were adequately described by the Langmuir model, reaching maximum adsorption capacities (qm) of 124 ± 1 μmol g-1, 315 ± 2 μmol g-1 and 201 ± 5 μmol g-1 for SMX, TMP and CIP, respectively. The selected functionalization increased qm by up to 58 % in comparison with the non-functionalized AC. The oxygen modified AC produced from a biomass waste remarkably improved its performance for an efficient application in the removal of antibiotics from wastewater.

Comparative study of Fe2+/H2O2 and Fe2+/persulfate systems on the pre-treatment process of real pharmaceutical wastewater

Advanced oxidation technologies based on hydroxyl radical (•OH) and sulfate radical (SO4-•) are two common types of advanced oxidation technologies, but there are not many reports on the application of advanced oxidation methods in actual wastewater pretreatment. This article compares the pre-treatment performance of Fe2+/H2O2 and Fe2+/Persulfate systems in actual pharmaceutical wastewater, and combines EEM, GC-MS, and toxicity testing results to explore the differences in TOC, COD, and NH3-N removal rates, optimal catalyst dosage, applicable pH range, toxicity of effluent after reaction, and pollutant structure between the two systems. The results indicate that the Fe2+/H2O2 system has a higher pollutant removal rate (TOC: 71.9%, COD: 66.9%, NH3-N: 34.1%), but also requires a higher catalyst (Fe2+) concentration (6.0 g/L), and its effluent exhibits characteristic peaks of aromatic proteins. The Fe2+/Persulfate system has a wider pH range (pH ≈ 3-7) and is more advantageous in treating wastewater containing more cyclic organic compounds, but the effluent contains some sulfur-containing compounds. In addition, toxicity tests have shown that the toxicity reduction effect of the Fe2+/Persulfate system is stronger than that of the Fe2+/H2O2 system.

Denim industry wastewater treatment by a heterogeneous solar-Fenton process catalyzed by Fe supported on recycled polyethylene terephthalate (PET) by ultrasonic modification

The textile industry is an important economic sector; however, its wastewater generates a great impact on the environment. A heterogeneous solar Fenton (HSF) process was evaluated for denim wastewater treatment. The catalyst was obtained through ultrasonic modification of recycled polyethylene terephthalate (PET) with Fe nanoparticles (PET/NPs- Fe3O4). The SFH process was optimized using surface response methodology with a face-centered central composite design considering the effects of the hydraulic retention time (10, 25, and 40 min), hydrogen peroxide dosage (500, 1000, and 1500 mg/L), and mass of the packed catalyst (4, 6 and 8 g) on the color, COD, and turbidity removal efficiencies. The operating conditions for maximum COD removal were H2O2 541.7 mg/L, HRT 33.9 min, and PET/NPs- Fe3O4 dose 7.9 g with solar radiation. The removal of 91.2% COD, 86.2% color, 90.4% turbidity, and 81.9% TOC was obtained at 14.2 kJ/L QUva. PET modification yielded 1.6 mg Fe/g PET, and the modification method does not allow Fe leaching. The effluent obtained from the SFH process complies with the maximum permissible limits in Mexican legislation in terms of COD, TOC, turbidity, and color and allows the reuse of PET.

Degradation of Ampicillin with antibiotic activity removal using persulfate and submersible UVC LED: Kinetics, mechanism, electrical energy and cost analysis

Effective water treatment to remove antibiotics and its activity from contaminated water is urgently needed to prevent antibiotic-resistant bacteria (ARB) emergence. In this study, we investigated degradation of Ampicillin (AMP), an extensively used β-lactam antibiotic, using submersible Ultraviolet C Light Emitting Diode (λmax = 276 nm) irradiation source, and Persulfate (UVC LED/PS system). Pseudo first order rate constant (kobs) for degradation of AMP (1 ppm) by UVC LED/PS system was determined to be 0.5133 min-1 (PS = 0.2 mM). kobs value at pH 2.5 (0.7259 min-1) was found to be higher than pH 6.5 (0.5133 min-1) and pH 12 (0.1745 min-1). kobs value for degradation of AMP in deionized water spiked with inorganic anions (Cl-=0.5369 min-1,SO42-=0.4545 min-1, NO3-=0.1526 min-1, HCO3-=0.0226 min-1), in real tap water (0.1182 min-1) and simulated ground water (0.0372 min-1) were presented. Radical scavenging experiment reveal involvement of sulfate radical anion and hydroxyl radical in UVC LED/PS system. EPR analysis confirms the generation of sulfate radical anion and hydroxyl radical. Importantly, 74% reduction of total organic carbon (TOC) occurred within 60 min of AMP treatment by UVC LED/PS system. Seven degradation by-products were identified by high resolution mass spectrometry, and degradation pathways were proposed. Antibacterial activity of AMP towards Bacillus subtilis and Staphylococcus aureus was completely removed after UVC LED/PS treatment. ECOSAR model predicted no very toxic degradation by-products generation by UVC LED/PS system. Electrical Energy per order (EEo) and cost of UVC LED/PS system were determined to be 0.9351 kW/m3/order and ₹ 7.91/m3 ($ 0.095/m3 or € 0.087/m3), respectively. Overall, this study highlights, UVC LED/PS system as energy efficient, low-cost, and its potential to emerge as sulfate radical anion based advanced oxidation process (AOP) to treat water with antibiotics.

Visible Light-Driven Photocatalytic Degradation of Methylene Blue Dye Using a Highly Efficient Mg-Al LDH@g-C3N4@Ag3PO4 Nanocomposite

The issue of water resource pollution resulting from the discharge of dyes is a matter of great concern for the environment. In this investigation, a new ternary heterogeneous Mg-Al LDH@g-C3N4X@Ag3PO4Y (X = wt % of g-C3N4 with respect to Mg-Al layered double hydroxide (LDH) and Y = wt % of Ag3PO4 loaded on Mg-Al LDH@g-C3N430) nanocomposite was prepared with the aim of increasing charge carrier separation and enhancement of photocatalytic performance to degrade methylene blue (MB) dye. The prepared samples were subjected to characterization via Fourier-transform infrared spectroscopy, field emission scanning electron microscopy, energy-dispersive X-ray, transmission electron microscopy, X-ray diffraction, UV-vis diffuse reflectance spectroscopy, photoluminescence, and photoelectrochemical analysis. It was observed that in the presence of the composite of Mg-Al LDH and g-C3N4, the photocatalytic decomposition of MB under 150 W mercury lamp illumination increases significantly as opposed to Mg-Al LDH alone, and the Mg-Al LDH@g-C3N4 level with Ag3PO4 coating causes the complete degradation of MB to occur in less time. The outcomes show that the Mg-Al LDH@g-C3N430@Ag3PO45 nanocomposite demonstrated the highest photodegradation activity (99%). Scavenger tests showed that the two most effective agents in the photodegradation of MB are holes and hydroxyl radicals, respectively. Finally, a type II heterojunction photocatalytic degradation mechanism for MB by Mg-Al LDH@g-C3N430@Ag3PO45 was proposed.

Advanced oxidation process of valsartan by activated peroxymonosulfate: Chemical characterization and ecotoxicological effects of its byproducts

In recent years, the antihypertensive drug Valsartan (VAL) has been detected in surface waters up to concentrations of 6300 ng/L, due to its high consumption and its mostly unchanged excretion. Moreover, wastewater treatment plants fail to completely mineralize/transform it, as evidenced by findings of up to 3800 ng/L in some effluents. In this paper, the possible degradation of VAL was evaluated through Fenton-like reaction with activation of peroxymonosulfate in the presence of Fe(II) under neutral conditions. Fourteen degradation byproducts were isolated and completely identified by both nuclear magnetic resonance and mass spectrometry, five of which were discovered for the first time, and a mechanism of their formation was proposed. Furthermore, the potential acute and chronic toxicity of valsartan and its byproducts in the aquatic environment were evaluated in key organisms of the freshwater trophic chain belonging to producers and consumers, the alga Raphidocelis subcapitata and the rotifer Brachionus calyciflorus, respectively. Acute effects occurred at concentrations in the order of tens/hundreds of mg/L, far from those of environmental concern. As regards chronic effects, algae were not particularly affected by the parent compound and its derivatives, while rotifers were less affected by derivatives (effective concentrations at units/tens of μg/L) compared to valsartan (effective concentrations at hundreds of ng/L).

Enzymatic degradation of tetracycline by Trametes versicolor laccase in a fluidized bed reactor

Laccase from Trametes Versicolor was successfully immobilized on gelatin beads by a crosslinking reaction with glutaraldehyde. Immobilized laccases showed better stability towards pH and temperature than free laccases. Moreover, the immobilized laccases retained a good relative activity of 85 % after 20 days of storage at 4 °C. The degradation of tetracycline (TC) was studied with immobilized enzymes in both batch and fluidized bed reactors (FBR). The average degradation rate (1.59 mg h-1 Uenzymes-1) estimated over 24 h in the FBR was almost 5 times higher than in the stirred tank reactor. Maximum degradation rate achieved was 72 ± 1 % with a circulation flow rate of 80 mL min-1 and addition of air at a flowrate of 15 mL min-1. Study of the stability of the active beads under reaction conditions, shows that 45 % of the TC was degraded after 5 cycles of 24 h each. The toxicity of the TC solution before and after treatment was also investigated with microtox assays.

3D printed monoliths: From powder to an efficient catalyst for antibiotic degradation

To improve the effectiveness and durability of wastewater treatment technologies, researchers are showing a growing interest in 3D printing technology. This technology has attracted significant interest owing to its ability to fabricate challenging complex geometries using different material compositions. This manuscript is focused on the development of 3D monoliths from noncommercial filaments, i.e., a powder blend of iron oxide and polylactic acid (PLA) at 15 wt% of the former. Different monolith designs have been prepared to improve the fluid dynamics of the process, so a simple cylinder (15-Fe3O4@PLA) and a cylinder with double the length and an internal mesh (15-Fe3O4@PLA-DM) were used. These monoliths were characterized by Scanning electron microscopy (SEM), Differential scanning calorimetry (DSC) and Mössbauer spectroscopy, then used for water-based ofloxacin degradation in a continuous down-up flow configuration. Additionally, computational fluid dynamics simulations were performed to estimate the degradation rate constants and analyze the distribution of fluid velocity and pollutant concentration along the 15-Fe3O4@PLA-reactor. The oxidant dose was also optimized to develop the highest degradation rate. The degradation of the target pollutant for those monoliths was 55 and 82 % under optimized conditions. In addition, the 15-Fe3O4@PLA-DM monolith was operated for long term experiments, keeping the degradation performance at a good 67 % for up to 120 h. Finally a fixed-bed reactor was mounted with printed pellets of the mixture (15:85), Fe3O4:PLA, after being ground in a range of 125-200 μm. Under this setup configuration, we observed the total degradation of ofloxacin. 3D printing technology is cheap, reproducible and time saving in the development of supported catalysts in comparison with conventional deposition techniques. Moreover, the leaching of active sites on streams was largely diminished. In fact under continuous operation the leached Fe concentration is below 0.1 ppm, corroborating the good adhesion of the catalyst in the PLA support.

Theoretical design of transition metal-doped oxo-triarylmethyl as a disposable platform for adsorption of ibuprofen

Emerging environmental contaminants have become a crucial environmental issue because of the highly toxic effluents emitted by factories. Ibuprofen (IBP), as a typical anti-inflammatory drug, is frequently detected in water sources. Therefore, its removal using various adsorbents has drawn great interest. Herein, the structural, electronic, energetic, and optical properties of pristine oxo-triarylmethyl (oxTAM) and transition metal-doped oxo-triarylmethyl (TM@oxTAM, TM = Sc, Ti, V, Cr, and Mn) for adsorption of the IBU drug were investigated using density functional theory (DFT) calculations implemented in Gaussian and VASP codes. Frontier molecular orbital (FMO), density of states (DOS), and electronic band structure results demonstrated that transition metal-doped oxTAM causes a significant reduction in the energy band gap (Eg) value of pristine oxTAM, with the highest decrease (30.14 %) in the case of Mn@oxTAM. It was found that transition metal doping onto oxTAM leads to an increase in the adsorption energies (1.20-2.64 eV) and charge density between transition metal and IBU. Natural bond orbital (NBO) analysis revealed that charge was effectively transferred from the IBU towards the transition metal, which was further analyzed by charge decomposition analysis (CDA). Furthermore, quantum theory of atoms in molecules (QTAIM), interaction region indicator (IRI), electron localization function (ELF), and radial distribution function (RDF) analyses revealed that the IBU is adsorbed on the Sc@oxTAM surface via covalent interactions, while electrostatic with partially covalent interactions are dominated in other IBU/TM@oxTAM complexes. The results suggest that TM doping on the oxTAM provides a new insight for developing photocatalyst-based covalent organic frameworks (COFs) to remove emerging pollutants in wastewater.

Non-steroidal anti-inflammatory drugs (NSAIDs) in the environment: Recent updates on the occurrence, fate, hazards and removal technologies

Non-steroidal Anti-inflammatory Drugs (NSAIDs) are extensively utilized pharmaceuticals worldwide. However, owing to the improper discharge and disposal practices, they have emerged as significant contaminants that are widely distributed in water, soils, and sewage sediments. This ubiquity poses a substantial threat to the ecosystem and human health. Consequently, it is imperative to develop rapid, cost-effective, efficient and reliable approaches for containing these substance in order to mitigate the deleterious impact of NSAIDs. This research provides a comprehensive review of the occurrence, fate, and hazards associated with NSAIDs in the general environment. Additionally, various removal technologies, including advanced oxidation processes, biodegradation, and adsorption, were systematically summarized. The study also presents a comparative analysis of the benefits and drawbacks of different removal technologies while interpreting challenges related to NSAIDs' removal and proposing strategies for future development.

Efficient degradation of 2,4-dichlorophenol by heterogeneous electro-Fenton using bulk carbon aerogels modified in situ with FeCo-LDH as cathodes: Operational parameters and mechanism exploration

In this study, an in situ grown FeCo-Layered double hydroxide anchored to the surface of a bulk carbon aerogel (FeCo-LDH/CA) for contaminant degradation during the heterogeneous electro-Fenton (EF) process. The results exhibited that the FeCo-LDH/CA cathode achieved 100% of 2,4-dichlorophenol (2,4-DCP = 20 mg/L) degradation within 120 min at pH = 3, application current 20 mA, and Na2SO4 concentration 0.05 M. Moreover, the degradation efficiency was impressive in the range of pH = 2-9. The coexistence of the Fe (III)/Fe (II) and Co (III)/Co (II) as active sites on the cathode surface promoted the in-situ decomposition of H2O2 to form reactive oxygen species (ROS). •OH and O2- were confirmed to be the major degradation pollutants of ROS. Furthermore, density functional theory (DFT) was used to predict the reaction sites of 2,4-DCP, and its possible degradation pathways were proposed. The toxicity of intermediate products was evaluated and decreased after degradation. In addition, the eight cycle experiments and the degradation of other typical contaminants demonstrated the satisfactory stability and applicability of the synthetic cathode. This study presents the preparation of an efficient and stable EF cathode, further promoting the application of iron-based composites in wastewater treatment.

Low-cost test rig for characterization of photocatalytic planar materials using photonically sized UV-A LED light sources

In the presented studies, a system for the characterization of planar photocatalysts was developed and tested. In the system, reference substances can be studied online with regard to their degradability and adsorption on photocatalytic materials. In order to perform accurate calculations of the quantum and photon efficiency of the catalysts, the LED arrays used were adjusted in their spacing by simulations so that a homogeneous light field is imaged on the catalysts. The system was tested with respect to measurement accuracy and reproducibility and the photocatalytic degradation of methylene blue, methyl orange and rhodamine B was investigated. Exemplarily, the reaction kinetics, photolysis and adsorption on the tested photocatalysts were determined for these compounds and the calculation was presented in detail. The exact construction plans and circuits as well as the sensors and their programming are presented in detail and should encourage other scientists to replicate the experimental setup, since especially in the field of photocatalysis research, often the results of publications cannot be compared with each other.

Comparative risk assessment studies estimating the hazard posed by long-term consumption of PPCPs in river water

This study assesses the risk due to Emerging Contaminants (ECs), present in Indian rivers - Ganga (650 million inhabitants), Yamuna (57 million inhabitants), and Musi (7,500,000 inhabitants), 13 ECs in total, have been used for risk assessment studies. Their concentrations (e.g., Fluconazole: 236950 μg/l, Ciprofloxacin: 31000 μg/l, Caffeine: 21.57 μg/l, etc.) were higher than the threshold concentrations for safe consumption (e.g. Fluconazole allowable level is 3.8 μg/l, and Ciprofloxacin allowable level is 0.51 μg/l). Three different pathways of emerging contaminants (ECs) transfer (oral water ingestion, oral fish ingestion, and dermal water contact) have been considered and the study is carried out in 2 ways: (i) deterministic and (ii) probabilistic approaches (using Monte Carlo iterative methods with 10000 simulations) with the aid of a software - Risk (version 7.5). The risk value, quantified by Hazard Quotient (HQ) is higher than the allowable limit of 1 for several compounds in the three rivers like Fluconazole (HQ = 18276.713), Ciprofloxacin (HQ = 278.675), Voriconazole (HQ = 14.578), Cetirizine (HQ = 1006.917), Moxifloxacin (HQ = 8.076), Caffeine (HQ = 55.150), and Ibuprofen (HQ = 9.503). Results show that Fluconazole and Caffeine pose the maximum risk in the rivers via the "oral pathway" that allows maximum transfer of the ECs present in the river (93% and 82% contribution to total risk). The risk values vary from nearly 25 times to 19000 times the United States Environmental Protection Agency (USEPA) threshold limit of 1 (e.g., Caffeine Infant Risk = 25.990 and Fluconazole Adult Risk = 18276.713). The most susceptible age group, from this study, is "Adults" (19-70 years old), who stand the chance of experiencing the adverse health hazards associated with prolonged over-exposure to the ECs present in the river waters. Musi has the maximum concentration of pollutants and requires immediate remediation measures. Further, both methods indicate that nearly 60-70% of the population in all the three study areas are at risk of developing health hazards associated with over-exposure to ECs regularly, making the areas inhabitable.

Accelerated Ultraviolet Treatment of Carbamazepine and NDMA in Water under 222 nm Irradiation

Krypton chloride (KrCl*) excimer ultraviolet (UV) light may provide advantages for contaminant degradation compared to conventional low-pressure (LP) UV. Direct and indirect photolysis as well as UV/hydrogen peroxide-driven advanced oxidation (AOP) of two chemical contaminants were investigated in laboratory grade water (LGW) and treated secondary effluent (SE) for LPUV and filtered KrCl* excimer lamps emitting at 254 and 222 nm, respectively. Carbamazepine (CBZ) and N-nitrosodimethylamine (NDMA) were chosen because of their unique molar absorption coefficient profiles, quantum yields (QYs) at 254 nm, and reaction rate constants with hydroxyl radical. Quantum yields and molar absorption coefficients at 222 nm for both CBZ and NDMA were determined, with measured molar absorption coefficients of 26 422 and 8170 M-1 cm-1, respectively, and QYs of 1.95 × 10-2 and 6.68 × 10-1 mol Einstein-1, respectively. The 222 nm irradiation of CBZ in SE improved degradation compared to that in LGW, likely through promotion of in situ radical formation. AOP conditions improved degradation of CBZ in LGW for both UV LP and KrCl* sources but did not improve NDMA decay. In SE, photolysis of CBZ resulted in decay similar to that of AOP, likely due to the in situ generation of radicals. Overall, the KrCl* 222 nm source significantly improves contaminant degradation compared to that of 254 nm LPUV.

Iron(III)-(1,10-Phenanthroline) Complex Can Enhance Ferrate(VI) and Ferrate(V) Oxidation of Organic Contaminants via Mediating Electron Transfer

Recent research has primarily focused on the utilization of reductants as activators for Fe(VI) to generate high-valent iron species (Fe(IV)/Fe(V)) for the degradation of emerging organic contaminants (EOCs). However, a significant drawback of this approach arises from the reaction between reductants and ferrates, leading to a decrease in oxidation capacity. This study introduces a novel discovery that highlights the potential of the iron(III)-(1,10-phenanthroline) (Fe(III)-Phen) complex as an activator, effectively enhancing the degradation of EOCs by Fe(VI) and augmenting the overall oxidation capacity of Fe(VI). The degradation of EOCs in the Fe(VI)/Fe(III)-Phen system is facilitated through two mechanisms: a direct electron transfer (DET) process and electron shuttle action. The DET process involves the formation of a Phen-Fe(III)-Fe(VI)* complex, which exhibits a stronger oxidation ability than Fe(VI) alone and can accept electrons directly from EOCs. On the other hand, the electron shuttle process utilizes Fe(III)-Phen as a redox mediator to transfer electrons from EOCs to Fe(VI) through the Fe(IV)/Fe(III) or Fe(IV)/Fe(II)/Fe(III) cycle. Moreover, the Fe(III)-Phen complex can improve the utilization efficiency of Fe(V) by preventing its self-decay. This study's findings may present a viable option for utilizing an effective catalyst to enhance the oxidation of EOCs by Fe(VI) and Fe(V).

Hybrid chitosan/molecularly imprinted polymer hydrogel beads doped with iron for selective ibuprofen adsorption

Pharmaceutical pollutants are a group of emerging contaminants frequently found in water streams. In this study, the composite chitosan beads with incorporated molecularly imprinted polymers (monoliths or microparticles) and iron(III) hydroxide were fabricated to remove ibuprofen from aqueous solutions. The adsorptive properties were investigated in different conditions to evaluate the influence of solution pH, adsorbent dose, ibuprofen initial concentration, adsorption time, and temperature. The highest adsorption capacity (79.41 mg g-1), about twice as large as that for the chitosan beads without polymers (39.42 mg g-1), was obtained for the ones containing monoliths imprinted with ibuprofen. The theoretical maximum adsorption capacity of 103.93 mg g-1 was obtained based on the experiments in optimal pH 5. The adsorption of ibuprofen on the hybrid hydrogel beads followed the Freundlich isotherm and pseudo-second-order kinetic models. The process was found as endothermic and thermodynamically spontaneous. The adsorbent with a molecularly imprinted polymer retained its selectivity in the presence of other molecules. The imprinted cavities, chitosan functional groups, and iron hydroxide were presumably responsible for interactions with ibuprofen molecules. Additionally, the effectiveness of the adsorbent did not change significantly in real water samples and remained at a satisfactory level for up to four desorption-adsorption cycles.

Scalability of advanced oxidation processes (AOPs) in industrial applications: A review

Disinfection and decontamination of water by application of oxidisers is an essential treatment step across numerous industrial sectors including potable supply and industry waste management, however, could be greatly enhanced if operated as advanced oxidation processes (AOPs). AOPs destroy contaminants including pathogens by uniquely harnessing radical chemistry. Despite AOPs offer great practical opportunities, no reviews to date have highlighted the critical AOP virtues that facilitate AOPs' scale up under growing industrial demand. Hence, this review analyses the critical AOP parameters such as oxidant conversion efficiency, batch mode vs continuous-flow systems, location of radical production, radical delivery by advanced micro-/mesoporous structures and AOP process costs to assist the translation of progressing developments of AOPs into their large-scale applications. Additionally, the state of the art is analysed for various AOP inducing radical/oxidiser measurement techniques and their half-lives with a view to identify radicals/oxidisers that are suitable for in-situ production. It is concluded that radicals with short half-lives such as hydroxyl (10-4 μsec) and sulfate (30-40 μsec) need to be produced in-situ via continuous-flow reactors for their effective transport and dosing. Meanwhile, radicals/oxidisers with longer half-lives such as ozone (7-10 min), hydrogen peroxide (stable for several hours), and hypochlorous acid (10 min -17 h) need to be applied through batch reactor systems due to their relatively longer stability during transportation and dosing. Complex and costly synthesis as well as cytotoxicity of many micro-/mesoporous structures limit their use in scaling up AOPs, particularly to immobilising and delivering the short-lived hydroxyl and sulfate radicals to their point of applications. Overall, radical delivery using safe and advanced biocompatible micro-/mesoporous structures, radical conversion efficiency using advanced reactor design and portability of AOPs are priority areas of development for scaling up to industry.

Multi-antibiotics removal under UV-A light using sol-gel prepared TiO2: Central composite design, effect of persulfate addition and degradation pathway study

The removal of three antibiotics i.e., metronidazole (MNZ), ciprofloxacin (CIP) and tetracycline (TET), from aqueous system via TiO2 photocatalysis under UV-A light was investigated. Photocatalyst(s) were prepared using sol-gel method under different calcination temperatures (400-800 °C) and water-alcohol ratio. The spherical shaped catalyst (mean particle size ∼ 61 nm) was characterized via FTIR, XRD, BET, SEM, Raman, XPS, UV-DRS, and Fluorometry, and point of zero charge was also determined (pHPZC ∼ 6.6). Batch photo-catalytic degradation studies have shown complete degradation of MNZ, CIP and TET after 50, 75 and 20 min with a TOC removal of 37%, 44% and 31%, respectively. The activity of sol-gel prepared TiO2 was comparatively higher than commercially available pure anatase TiO2 nanoparticles due to lesser mean particle size. The ratio of water to alcohol in the preparation of TiO2 catalyst was found to have significant effect on antibiotic removal. Moreover, persulfate (PS) addition of 0.1 g/L amplified the pseudo-first-order removal-rate constant by 2.75, 3.3 and 1.6 times for MNZ, CIP and TET, respectively. The higher initial pH values (8 and 10) have shown the best removal efficiency for all antibiotics. Subsequently, central composite design (CCD) experiments were conducted under multi-antibiotic conditions. Near complete removal of all antibiotics were observed within 120 min. Scavenging studies revealed that hydroxyl and superoxide radicals play major roles in photo-catalytic degradation of MNZ, CIP and TET. During photocatalysis, MNZ degradation was initiated by hydroxylation reaction, CIP by piperazine ring opening by hydroxyl attack and TET by multiple hydroxylation process. Overall, TiO2 showed good efficiency at degrading multiple antibiotics and has the potential for practical application on a larger scale.

Synergistic Remediation of Organic Dye by Titanium Dioxide/Reduced Graphene Oxide Nanocomposite

In this work, nanocomposites based on titanium dioxide and reduced graphene oxide (TiO2@rGO) with different weight percentages of rGO (4, 8, and 16 wt%) were prepared by the hydrothermal/solvothermal synthesis method and thermally treated at 300 °C. The prepared nanocomposites were explored for the removal of methylene blue dye (MB) in the presence of simulated solar illumination as well as natural sunlight. The structural, morphological, chemical, and optical properties of the as-synthesized TiO2@rGO nanocomposites were characterized. The obtained results of the graphene-based nanocomposite materials indicated the existence of interactions between TiO2 and rGO, i.e., the Ti-O-C bond, which confirmed the successful integration of both components to form the TiO2@rGO nanocomposites. The addition of rGO increased the specific surface area, decreased the band gap energy, and increased the photocatalytic degradation efficiency of MB from water compared to TiO2 nanoparticles. The results of photocatalytic activity indicated that the amount of rGO in the prepared TiO2@rGO nanocomposites played a significant role in the application of different photocatalytic parameters, including the initial dye concentration, catalyst concentration, water environment, and illumination source. Our studies show that the reinforcement of the nanocomposite with 8 wt% of rGO allowed us to obtain the maximum photocatalytic decomposition performance of MB (10 mg·L-1) with a removal percentage of 99.20 after 2 h. Additionally, the obtained results show that the prepared TiO2@rGO_8 wt% nanocomposite can be used in three consecutive cycles while maintaining photocatalytic activity over 90%.

Facile fabrication of plasmonic Ag/ZIF-8: an efficient catalyst for investigation of antibacterial, haemolytic and photocatalytic degradation of antibiotics

Present article represents the fabrication of plasmonic Ag/ZIF-8 composite and its effect on antibacterial, haemolytic and photocatalytic degradation of antibiotics. Ag/ZIF-8 was prepared by varying molar concentrations (1 mM, 2.5 mM, and 5 mM) of AgNO3 into ZIF-8 using NaBH4 as a reducing agent by the sol-gel process. The material was then characterised using the XRD, XPS, FTIR, SEM, HRTEM, UVDRS, BET and EIS techniques. When it comes to breaking down the antibiotic CIP, the optimised Ag2.5/ZIF-8 exhibits the strongest photocatalytic capability, with a degradation efficiency of 82.3% after 90 minutes. Due to LSPR (Localised Surface Plasmon Resonance) as well as the efficient movement and separation of the interfaces of photo-generated charge carriers in Ag2.5/ZIF-8 may be the causes of this increase in photocatalytic degradation. The effect of several parameters, such as pH, a variety of catalysts, varying dose concentrations, scavenging and sustainability are being investigated. The para benzoquinone (OH˙) and citric acid (h+) the primary active species in the photocatalytic breakdown pathway, according to trapping study. Whereas, Ag5/ZIF-8 was optimised for greater antibacterial activity against S. aureus and E. coli due to the synergistic impact of Ag+ and Zn2+ in Ag5/ZIF-8 and in haemolytic experiment, all samples were discovered to be non-toxic to blood cells. Overall, the synthesised compound was discovered to be a reusable, affordable catalyst for water remediation that can also be used in biomedicine.

Pharmaceutically active compounds in aqueous environment: recent developments in their fate, occurrence and elimination for efficient water purification

The existence of pharmaceutically active compounds (PhACs) in the water is a major concern for environmentalists due to their deleterious effects on living organisms even at minuscule concentrations. This review focuses on PhACs such as analgesics and anti-inflammatory compounds, which are massively excreted in urine and account for the majority of pharmaceutical pollution. Furthermore, other PhACs such as anti-epileptics, beta-blockers and antibiotics are discussed because they also contribute significantly to pharmaceutical pollution in the aquatic environment. This review is divided into two parts. In the first part, different classes of PhACs and their fate in the wastewater environment are presented. In the second part, recent advances in the removal of PhACs by conventional wastewater treatment plants, including membrane bioreactors (MBRs), activated carbon adsorption and bench-scale studies concerning a broad range of advanced oxidation processes (AOPs) that render practical and appropriate strategies for the complete mineralization and degradation of pharmaceutical drugs, are reviewed. This review indicates that drugs like diclofenac, naproxen, paracetamol and aspirin are removed efficiently by conventional systems. Activated carbon adsorption is suitable for the removal of diclofenac and carbamazepine, whereas AOPs are leading water treatment strategies for the effective removal of reviewed PhACs.

Advanced electrocatalytic redox processes for environmental remediation of halogenated organic water pollutants

Halogenated organic compounds are widespread, and decades of heavy use have resulted in global bioaccumulation and contamination of the environment, including water sources. Here, we introduce the most common halogenated organic water pollutants, their classification by type of halogen (fluorine, chlorine, or bromine), important policies and regulations, main applications, and environmental and human health risks. Remediation techniques are outlined with particular emphasis on carbon-halogen bond strengths. Aqueous advanced redox processes are discussed, highlighting mechanistic details, including electrochemical oxidations and reductions of the water-oxygen system, and thermodynamic potentials, protonation states, and lifetimes of radicals and reactive oxygen species in aqueous electrolytes at different pH conditions. The state of the art of aqueous advanced redox processes for brominated, chlorinated, and fluorinated organic compounds is presented, along with reported mechanisms for aqueous destruction of select PFAS (per- and polyfluoroalkyl substances). Future research directions for aqueous electrocatalytic destruction of organohalogens are identified, emphasizing the crucial need for developing a quantitative mechanistic understanding of degradation pathways, the improvement of analytical detection methods for organohalogens and transient species during advanced redox processes, and the development of new catalysts and processes that are globally scalable.

New insight into the removal process of benzotriazole UV stabilizers by UV/H2O2: Integrating quantum chemical calculation with CFD simulation

Benzotriazole UV stabilizers (BT-UVs) are important UV absorbers. As high-production chemicals and potential hazards, their ubiquitous presence in aquatic environments is of greatly pressing concern. Herein, the removal of six typical BT-UVs by UV/H2O2 was comprehensively investigated by quantum chemistry calculation integrated with CFD simulation. Utilizing such a micro and macro incorporated model in treating contaminants is the first report. From the micro-view, degradation mechanisms of BT-UVs by •OH oxidation were determined, and corresponding rate constants were obtained with values of 109∼1010 M-1s-1. In a macroscopic aspect, combining the established kinetic model and CFD simulation, the effects of UV lamp power (P), volumetric flow rate (Qv), and H2O2 dosage ([H2O2]0) on removal yields of BT-UVs were expounded, increasing P or [H2O2]0 or decreasing Qv are effective in improving removal yields of BT-UVs, but the enhancement was abated when P or [H2O2]0 increased to a certain level. When [H2O2]0 is 5 mg/L and Qv is decreased from 0.1 to 0.05 m3/h, the removal yields of BT-UVs could achieve more than 95% (P = 150 W) and 99% (P = 250 W), respectively. This work provides a new interdisciplinary insight for investigating organic contaminant removal in potential industrial applications of UV/H2O2 systems.

Performance and mechanism of FeS2/FeSxOy as highly effective Fenton-like catalyst for phenol degradation

Developing a highly efficient Fenton-like catalyst working in a wide pH range is imperative to accomplish its practical wastewater treatment. Herein, FeS2/FeSxOy catalyst was synthesized by hydrothermal-solvothermal vulcanization with thioacetamide as a sulfur source. Characterization results confirmed FeS2/FeSxOy consisted of pyrite, kornelite, and szomolnokite. FeS2/FeSxOy exhibited superior catalytic activity toward H2O2 activation with more than 96% phenol removal within 5 min in pH 3.0 ∼ 8.0 at 30°C. Radical scavenging experiment and EPR analysis revealed both hydroxyl radicals (·OH) and superoxide anion radicals (O2·-) anticipated in phenol elimination, but ·OH played a dominant role. The detailed degradation experiments and density functional theory (DFT) calculation confirmed the vital role of FeS2 in enhancing phenol abatement. This study not only developed a highly active catalyst for H2O2 activation but also theoretically analyzed the FeS2 function in depth, which provided a guide for designing a highly efficient Fenton-like catalyst.

Low-temperature molten-salt synthesis of Co3O4 nanoparticles grown on MXene can rapidly remove ornidazole via peroxymonosulfate activation

We further developed previous work on MXene materials prepared using molten salt methodology. We substituted single, with mixed salts, and reduced the melting point from >724 °C to <360 °C. Cobalt (Co) compounds were simultaneously etched and doped while the MXene material was created using various techniques in which Co compounds occur as Co3O4. The synthesized Co3O4/MXene compound was used as a peroxymonosulfate (PMS) activator that would generate free radicals to degrade antibiotic ornidazole (ONZ). Under optimal conditions, almost 100% of ONZ (30 mg/L) was degraded within 10 min. The Co3O4/MXene + PMS system efficiently degraded ONZ in natural water bodies, and had a broad pH adaptation range (4-11), and strong anion anti-interference. We investigated how the four active substances were generated using radical quenching and electron paramagnetic resonance (EPR) spectroscopy. We identified 12 ONZ intermediates by liquid chromatography-mass spectrometry and propose a plausible degradative mechanism.

Elucidating sulfate radical-induced oxidizing mechanisms of solid-phase pharmaceuticals: Comparison with liquid-phase reactions

As a class of organic micropollutants of global concern, pharmaceuticals have prevalent distributions in the aqueous environment (e.g., groundwater and surface water) and solid matrices (e.g., soil, sediments, and dried sludge). Their contamination levels have been further aggravated by the annually increased production of expired drugs as emerging harmful wastes worldwide. Sulfate radicals (SO4•-)-based oxidation has attracted increasing attention for abating pharmaceuticals in the environment, whereas the transformation mechanisms of solid-phase pharmaceuticals remain unknown thus far. This investigation presented for the first time that SO4•-, individually produced by mechanical force-activated and heat-activated persulfate treatments, could effectively oxidize three model pharmaceuticals (i.e., methotrexate, sitagliptin, and salbutamol) in both solid and liquid phases. The high-resolution mass spectrometric analysis suggested their distinct transformation products formed by different phases of SO4•- oxidation. Accordingly, the SO4•--mediated mechanistic differences between the solid-phase and liquid-phase pharmaceuticals were proposed. It is noteworthy that the products from both systems were predicted with the remaining persistence, bioaccumulation, and multi-endpoint toxicity. Therefore, some post-treatment strategies need to be considered during practical applications of SO4•--based technologies in remediating different phases of micropollutants. This work has environmental implications for understanding the comparative transformation mechanisms of pharmaceuticals by SO4•- oxidation in remediating the contaminated solid and aqueous matrices.

A Theoretical Study on the Degradation Mechanism, Kinetics, and Ecotoxicity of Metronidazole (MNZ) in •OH- and SO4•--Assisted Advanced Oxidation Processes

Metronidazole (MNZ), a typical example of nitroimidazole antibiotics, is widely used in the treatment of infectious diseases caused by anaerobic bacteria. The degradation mechanism and kinetics of MNZ in the presence of HO• and SO4•- were studied using density functional theory (DFT). It was confirmed that both HO• and SO4•- easily added to the carbon atom bonded to the NO2 group in the MNZ molecule as the most feasible reaction channel. This study shows that subsequent reactions of the most important product (M-P) include the O2 addition, hydrogen abstraction and bond breakage mechanisms. The rate constants of HO• and SO4•--initiated MNZ in the aqueous phase were calculated in the temperature range of 278-318 K. The total rate constants of MNZ with HO• and SO4•- were determined to be 8.52 × 109 and 1.69 × 109 M-1s-1 at 298 K, which were consistent with experimental values of (3.54 ± 0.42) × 109 and (2.74 ± 0.13) × 109 M-1s-1, respectively. The toxicity of MNZ and its degradation products to aquatic organisms has been predicted. The results proposed that the toxicity of the initial degradation product (M-P) was higher than that of MNZ. However, further degradation products of MNZ induced by HO• were not harmful to three aquatic organisms (fish, daphnia, and green algae). This study provides a comprehensive theoretical basis for understanding the degradation behavior of MNZ.

Nanostructured copper-organic frameworks for the generation of sulphate radicals: application in wastewater disinfection

In recent years, the presence of pathogens in the environment has become an issue of widespread concern in society. Thus, new research lines have been developed regarding the removal of pathogens and persistent pollutants in water. In this research, the efficacy of nanostructure copper-organic framework, HKUST-1, has been evaluated for its ability to eliminate Escherichia coli and generate sulphate radicals as catalyst for the treatment of effluents with a high microbiological load via peroxymonosulphate (PMS) activation. The disinfection process has been optimized, achieving complete elimination of Escherichia coli growth after 30 min of testing using a concentration of 60.5 mg/L HKUST-1 and 0.1 mM of PMS. To overcome the operational limitations of this system and facilitate its handling and reutilization in a flow disinfection process, HKUST-1 has been efficiently encapsulated on polyacrylonitrile as a novel development that could be scaled up to achieve continuous treatment.

Rice husk coated with copper oxide nanoparticles for 17α-ethinylestradiol removal from an aqueous solution: adsorption mechanisms and kinetics

The 17 α-ethinylestradiol (EE2) adsorption from aqueous solution was examined using a novel adsorbent made from rice husk powder coated with CuO nanoparticles (CRH). Advanced analyses of FTIR, XRD, SEM, and EDSwere used to identify the classification parameters of a CRH-like surface morphology, configuration, and functional groups. The rice husk was coated with CuO nanoparticles, allowing it to create large surface area materials with significantly improved textural qualities with regard to functional use and adsorption performance, according to a detailed characterization of the synthesized materials. The adsorption process was applied successfully with elimination effectiveness of 100% which can be kept up to 61.3%. The parameters of adsorption were affecting the adsorption process significantly. Thermodynamic data stated that the process of adsorption was endothermic, spontaneous, chemisorption and the molecules of EE2 show affinity with the CRH. It was discovered that the adsorption process controlled by a pseudo-second-order kinetic model demonstrates that the chemisorption process was controlling EE2 removal. The Sips model is regarded as optimal for representing this practice, exhibiting a significantly high determination coefficient of 0.948. This coefficient implies that the adsorption mechanism indicates the occurrence of both heterogeneous and homogeneous adsorption. According to the findings, biomass can serve as a cheap, operative sorbent to remove estrogen from liquified solutions.

Carbon Gels-Green Graphene Composites as Metal-Free Bifunctional Electro-Fenton Catalysts

The Electro-Fenton (EF) process has emerged as a promising technology for pollutant removal. However, the EF process requires the use of two catalysts: one acting as an electrocatalyst for the reduction of oxygen to H2O2 and another Fenton-type catalyst for the generation of ·OH radicals from H2O2. Thus, the search for materials with bifunctionality for both processes is required for a practical and real application of the EF process. Thus, in this work, bifunctional electrocatalysts were obtained via doping carbon microspheres with Eco-graphene, a form of graphene produced using eco-friendly methods. The incorporation of Eco-graphene offers numerous advantages to the catalysts, including enhanced conductivity, leading to more efficient electron transfer during the Electro-Fenton process. Additionally, the synthesis induced structural defects that serve as active sites, promoting the direct production of hydroxyl radicals via a 3-electron pathway. Furthermore, the spherical morphology of carbon xerogels enhances the accessibility of the reagents to the active sites. This combination of factors results in the effective degradation of Tetracycline (TTC) using metal-free catalysts in the Electro-Fenton process, achieving up to an impressive 83% degradation without requiring any other external or additional catalyst.

CaCu3Ti4O12 Perovskite Materials for Advanced Oxidation Processes for Water Treatment

The many pollutants detected in water represent a global environmental issue. Emerging and persistent organic pollutants are particularly difficult to remove using traditional treatment methods. Electro-oxidation and sulfate-radical-based advanced oxidation processes are innovative removal methods for these contaminants. These approaches rely on the generation of hydroxyl and sulfate radicals during electro-oxidation and sulfate activation, respectively. In addition, hybrid activation, in which these methods are combined, is interesting because of the synergistic effect of hydroxyl and sulfate radicals. Hybrid activation effectiveness in pollutant removal can be influenced by various factors, particularly the materials used for the anode. This review focuses on various organic pollutants. However, it focuses more on pharmaceutical pollutants, particularly paracetamol, as this is the most frequently detected emerging pollutant. It then discusses electro-oxidation, photocatalysis and sulfate radicals, highlighting their unique advantages and their performance for water treatment. It focuses on perovskite oxides as an anode material, with a particular interest in calcium copper titanate (CCTO), due to its unique properties. The review describes different CCTO synthesis techniques, modifications, and applications for water remediation.