Sub-stoichiometric titanium oxide (Ti4O7) as a suitable ceramic anode for electrooxidation of organic pollutants: A case study of kinetics, mineralization and toxicity assessment of amoxicillin

Antibiotic amoxicillin degradation by electrochemical oxidation process: effects of process parameters and degradation pathway at environmentally relevant concentrations

Amoxicillin (AMX) is a common antibiotic used in both human and veterinary medicine in order to both cure and avoid bacterial infections. Traces of AMX have been found in ground and surface water, urban effluents, water, and wastewater treatment facilities due to its widespread use. The level of hazard and disposal of this class of micropollutants is the reason for concern. Advanced technology is required since conventional wastewater treatment plants are ineffective at eliminating these emerging contaminants. Electrochemical oxidation is a promising method of treating wastewater, which uses electrogenerated radicals to mineralize organic pollutants. This work investigated the detailed process mechanism for AMX degradation utilizing a low-cost, thin, flexible graphite sheet with lower AMX concentrations, initial pH value, voltage, electrolyte concentration, and wastewater matrix. The degradation of AMX by in situ generated hydroxyl radicals is a function of applied voltage and follows pseudo-first-order reaction kinetics. The removal efficiencies of AMX have been achieved up to 99% within 3 h. Moreover, intermediate by-products have been identified using liquid chromatography-mass spectrometry, and a plausible pathway has been proposed. This study could serve as a process reference for controlling AMX wastewater contamination via the electrochemical oxidation technique.

Electrochemical advanced oxidation combined to electro-Fenton for effective treatment of perfluoroalkyl substances "PFAS" in water using a Magnéli phase-based anode

Per-and polyfluoroalkyl substances (PFAS), known as "forever chemicals", are posing a considerable threat to human health and the environment, that conventional treatment methods are unable to treat. In recent years, electrochemical advanced oxidation emerged as a promising technology for the degradation of recalcitrant pollutants such as PFAS. This work reports the degradation of perfluorooctanoic acid (PFOA) and perfluorooctanesulfonic acid (PFOS), using a Magnéli phase-based anode type Ti4O7 by electro-oxidation and electro-oxidation combined with electro-Fenton. First the Ti4O7 anode was prepared from Rutile TiO2 powder and characterized, the results showed that the Ti n O2n-1 phase is the dominant phase. Afterward, the degradation of PFOA and PFOS was evaluated on the developed anode. After 5 hours of treatment, 52% and 82% of PFOA and PFOS were removed respectively. To improve this results electro-oxidation was combined with electro-Fenton, the degradation of both pollutants increased, 92% of PFOA was degraded and PFOS was totally removed after 5 hours of treatment. The energy consumption was also evaluated at t 1/2 which is defined as the time when half of the initial concentration of PFOA and PFOS was degraded. Combining the two degradation approaches showed promising results that need to be further optimized for potential application at large volumes.

Principles, challenges and prospects for electro-oxidation treatment of oilfield produced water

The oil industry is facing substantial environmental challenges, especially in managing waste streams such as Oilfield Produced Water (OPW), which represents a significant component of the industrial ecological footprint. Conventional treatment methods often fail to effectively remove dissolved oils and grease compounds, leading to operational difficulties and incomplete remediation. Electrochemical oxidation (EO) has emerged as a promising alternative due to its operational simplicity and ability to degrade pollutants directly and indirectly, which has already been applied in treating several effluents containing organic compounds. The application of EO treatment for OPW is still in an initial stage, due to the intricate nature of this matrix and scattered information about it. This study provides a technological overview of EO technology for OPW treatment, from laboratory scale to the development of large-scale prototypes, identifying design and process parameters that can potentially permit high efficiency, applicability, and commercial deployment. Research in this domain has demonstrated notable rates of removal of recalcitrant pollutants (>90%), utilizing active and non-active electrodes. Electro-generated active species, primarily from chloride, play a pivotal role in the oxidation of organic compounds. However, the highly saline conditions in OPW hinder the complete mineralization of these organics, which can be improved by using non-active anodes and lower salinity levels. The performance of electrodes greatly influences the efficiency and effectiveness of OPW treatment. Various factors must be considered when selecting the electrode material, such as its conductivity, stability, surface area, corrosion resistance, and cost. Additionally, the specific contaminants present in the OPW, and their electrochemical reactivity must be considered to ensure optimal treatment outcomes. Balancing these considerations can be challenging, but it is crucial for achieving successful OPW treatment. Active electrode materials exhibit a high affinity for chloride molecules, generating more active species than non-active materials, which exhibit more significant degradation potential due to the production of hydroxyl radicals. Regarding scale-up, key challenges include low current efficiency, the formation of by-products, electrode deactivation, and limitations in mass transfer. To address these issues, enhanced mass transfer rates and appropriate residence times can be achieved using flow-through mesh anodes and moderate current densities, which have proven to be the optimal configuration for this process.

Efficient electro-oxidation-based degradation of per- and polyfluoroalkyl (PFAS) persistent pollutants by using plasma torch synthesized pure-Magnéli phase-Ti4O7 anodes

Pure Magnéli-phase Ti4O7 were prepared by means of a Plasma Torch (PT) coating method and integrated into an advanced electro-catalytic oxidation (AEO) process in order to degrade perfluorooctanoic acid (PFOA) and perfluorooctanesulfonic acid (PFOS) persistent pollutants present in waters. The X-ray diffraction analysis confirmed the polycrystalline nature of the pure Magnéli phase PT-Ti4O7 coatings (∼100 μm thick)). The Raman spectra of the PT-Ti4O7 coatings also exhibited the two characteristic peaks (at 138 and 183 cm-1) of the PT-Ti4O7 Magnéli phase. Scanning electron microscopy revealed the nanostructured hierarchical morphology of the PT-Ti4O7 thus conferring them high surface area. The PT-Ti4O7 anodes are shown to achieve higher degradation efficiencies towards PFOA and PFOS in comparison with the conventional boron-doped diamond anodes. By investigating several AEO parameters (including current density, treatment time, nature of the anode material), we were able to optimise the AEO process. Thus, for both PFOA and PFOS (at an initial concentration of 500 ppb in synthetic wastewaters), degradation efficiencies as high as 96.6% and 99.7% were achieved, respectively, with a current density of 20 mA/cm2, a treatment time of 120 min and PT-Ti4O7 mesh-type anodes. PFOA and PFOS can be degraded by both direct anodic electrochemical oxidation (•OH radicals) and indirect electrochemical oxidation via mediators, such as persulphate acid (H2S2O8) generated by sulphate anodic oxidation. The degradation of both compounds followed pseudo-first-order kinetics. The reaction rate constant (k) for PFOS removal was 4.63 × 10-2 min-1, whereas 2.76 × 10-2 min-1 was recorded for PFOA removal. Subsequently, we have used the above optimal AEO operating conditions to treat real wastewater effluents (containing 17 types of PFAS molecules with a total content of 8500 ppb) and achieved a degradation rate of 39.1%-87.4% for eight of the 17 PFAS compounds. The degradation rate was found to be dependent on the chemical structure and chain length of each PFOA/PFOS component.

Enhanced Mineralization of Organic Pollutants through Atomic Hydrogen-Mediated Alternative Transformation Pathways

Electrocatalytic hydrogen atom-hydroxyl radical (H*-·OH) redox system is a promising approach for contaminant removal and mineralization. However, its working mechanism, especially the effect of H*, remains unclear, hindering its practical application. Herein, we constructed an electrochemical reactor equipped with our self-made Pd-loaded Ti/TiO2 nanotube cathode and a commercial boron-doped diamond anode. After fulfilling the electrode characterization and free radical detection, we employed coumarin and 7-azido-4-methylcoumarin as probes to confirm the participation of H* in the transformation of organic compounds. A comprehensive study on the degradation kinetics, reaction, and mineralization mechanisms using benzoic acid (BA) and 4-chlorophenol (4-CP) as model compounds was further conducted. The rate constants and total organic carbon removal of BA and 4-CP in the redox system increased compared with those of the individual oxidation and reduction processes. Theoretical calculations demonstrate that H* opens up alternative pathways for BA and 4-CP ring cleavage, forming quinones as reactive intermediates. Furthermore, H* facilitates the mineralization of the typical intermediates, maleic acid and fumaric acid, through C=C bond addition and H-abstraction from the 1,1-diol structure. The presence of H* provides alternative pathways for pollutant transformation, consequently reducing the treatment duration.

Electrochemical oxidation of surfactants as an essential step to enable greywater reuse

The practical application of electrochemical oxidation technology for the removal of surfactants from greywater was evaluated using sodium dodecyl sulfate (SDS) as a model surfactant. Careful selection of electrocatalysts and optimization of operational parameters demonstrated effective SDS removal in treating a complex greywater matrix with energy consumption below 1 kWh g-1 COD (Chemical Oxygen Demand), paving the way for a more sustainable approach to achieving surfactant removal in greywater treatment when aiming for decentralized water reuse. Chromatographic techniques identified carboxylic acids as key byproducts prior to complete mineralization. These innovative approaches represent a novel pathway for harnessing electrochemical technologies within decentralized compact devices, offering a promising avenue for further advancements in this field.

A Comprehensive Review on Modification of Titanium Dioxide-Based Catalysts in Advanced Oxidation Processes for Water Treatment

It has become necessary to develop effective strategies to prevent and reduce water pollution as a result of the increase in dangerous pollutants in water reservoirs. Consequently, there is a need to design new catalyst materials to promote the efficiency of advanced oxidation processes (AOPs) in the field of wastewater treatment plant to ensure the mineralization of trace organic contaminants. A notable approach gaining attention involves the coupling of sulfate radicals-based AOPs to photocatalysis or electrocatalysis processes, aiming to achieve the complete removal of refractory contaminants into water and carbon dioxide. Titanium dioxide as metal oxide has received great attention for its catalytic application in water purification. TiO2 catalysts offer a multitude of advantages in AOPs. They are characterized by their high photocatalytic activity under both ultraviolet and visible light, making them environmentally friendly due to the absence of toxic byproducts during oxidation. Their versatility is remarkable, finding utility in various AOPs, from photocatalysis to photo-Fenton processes. TiO2's durability ensures long-lasting catalytic activity, which is crucial for continuous treatment processes, and their cost-effectiveness is particularly advantageous. Furthermore, their chemical stability allows it to withstand varying pH conditions. However, the large band gap energy and low electrical conductivity hinder the catalytic reaction effectiveness. This review aims to examine various approaches to enhance the catalytic performance of titanium dioxide, with the objective of enabling more efficient water purification methods.

Enhanced oxidation of organic pollutants by regulating the interior reaction region of reactive electrochemical membranes

Reactive electrochemical membrane (REM) emerges as an attractive strategy for the elimination of refractory organic pollutants that exist in wastewater. However, the limited reaction sites in traditional REMs greatly hinder its practical application. Herein, a feed-through coating methodology was developed to realize the uniform loading of SnO2-Sb catalysts on the interior surface of a REM. The uniformly coated REM (Unif-REM) exhibited 2.4 times higher reaction kinetics (0.29 min-1) than that of surface coated REM (Surf-REM) for the degradation of 2 mM 4-chlorophenol (4-CP), rendering an energy consumption as low as 0.016 kWh gTOC-1. The fast degradation of various emerging contaminants, e.g., sulfamethoxazole (SMX), ofloxacin (OFLX), and tetracycline (TC), also confirms its superior oxidation capability. Besides, the Unif-REM exhibited good performance in generating hydroxyl radicals (•OH) and a relatively long service lifetime. The simulation of spatial current distribution demonstrates that the interior reaction region in the Unif-REM channels can be drastically extended, thereby maximizing the surface coupling of mass diffusion and electron transfer. This study offers an in-depth look at the spatially confined reactions in REM and provides a reference for the design of electrochemical systems with economically efficient water purification.

Electrochemical degradation of key drugs to treat COVID-19: Experimental analysis of the toxic by-products formation (PCDD/Fs)

Drug consumption has grown exponentially in recent decades, particularly during the COVID-19 pandemic, leading to their presence in various water sources. In this way, degradation technologies for pollutants, such as electrochemical oxidation (ELOX), have become crucial to safeguard the quality of natural resources. This study has as its starting point a previous research, which demonstrated the efficacy of ELOX in the removal of COVID-19 related-drugs, such as dexamethasone (DEX), paracetamol (PAR), amoxicillin (AMX), and sertraline (STR), using the electrolytes NaCl and Na2SO4. The present research aims to study the potential risks associated with the generation of toxic by-products, during the ELOX of cited drugs, specifically focusing on the highly chlorinated persistent organic pollutants (POPs), such as polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). Dioxins and furans can be formed potentially in electrochemical systems from precursor molecules or non-precursor molecules in chloride medium. First, the degradation of the parent compounds was found to be complete. At this point, a comprehensive investigation was conducted to identify and analyse the by-products formed during the degradation process; precursors of PCDD/Fs, such as chlorophenols or hydroquinones were identified. Additionally, in continuation of the previous study, PCDD/Fs congeners were investigated, revealing elevated concentrations; the highest concentration obtained was for the congener 1,2,3,4,6,7,8-HpCDF (234.6 pg L-1 in NaCl) during degradation of the AMX. Finally, an assessment of the toxicity based on TEQ values was conducted, with DEX exhibiting the highest concentration among all compounds: 30.1 pg L-1 for NaCl medium. Therefore, the formation of minor by-products should not be underestimated, as they can significantly enhance the toxicity of the final sample, so the selection of the appropriate remediation technology, as well as the optimization of experimental operating variables, is determining in the treatment of pharmaceutical-contaminated waters.

Shifting Emphasis from Electro- to Catalytically Active Sites: Effects of Pore Size of Flow-Through Anodes on Water Purification

A flow-through anode has demonstrated high efficiency for micropollutant abatement in water purification. In addition to developing novel electrode materials, a rational design of its porous structure is crucial to achieve high electrooxidation kinetics while sustaining a low cost for flow-through operation. However, our knowledge of the relationship between the pore structure and its performance is still incomplete. Therefore, we systematically explore the effect of pore size (with a median from 4.7 to 49.4 μm) on the flow-through anode efficiency. Results showed that when the pore size was <26.7 μm, the electrooxidation kinetics was insignificantly improved, but the permeability declined dramatically. Traditional empirical evidence from hydrodynamic modeling and electrochemical tests indicated that a flow-through anode with a smaller pore size (e.g., 4.7 μm) had a high mass transfer capability and large electroactive area. However, this did not further accelerate the micropollutant removal. Combining an overpotential distribution model and an imprinting method has revealed that the reactivity of a flow-through anode is related to the catalytically active volume/sites. The rapid overpotential decay as a function of depth in the anode would offset the merits arising from a small pore size. Herein, we demonstrate an optimal pore size distribution (∼20 μm) of typical flow-through anodes to maximize the process performance at a low energy cost, providing insights into the design of advanced flow-through anodes in water purification applications.

Insights into antibiotic cefaclor mineralization by electro-Fenton and photoelectro-Fenton processes using a Ti/Ti4O7 anode: Performance, mechanism, and toxic chlorate/perchlorate formation

A comparative degradation of antibiotic cefaclor (CEC) between Ti/Ti4O7 and Ti/RuO2 anodes, in terms of degradation kinetics, mineralization efficiency, and formation of toxic chlorate (ClO3-) and perchlorate (ClO4-), was performed with electrochemical-oxidation (EO), electro-Fenton (EF), and photoelectro-Fenton (PEF) processes. Besides, CEC degradation by EF with boron-doped diamond (BDD) anode was also tested. Results showed CEC decays always followed pseudo-first-order kinetics, with increasing apparent rate constants in the sequence of EO < EF < PEF. The mineralization efficiency of the processes with Ti/Ti4O7 anode was higher than that of Ti/RuO2 anode, but slightly lower than that of BDD anode. Under the optimal conditions, 94.8% mineralization was obtained in Ti/Ti4O7-PEF, which was much higher than 64.4% in Ti/RuO2-PEF. The use of Ti/RuO2 gave no generation of ClO3- or ClO4-, while the use of Ti/Ti4O7 yielded a small amount of ClO3- and trace amounts of ClO4-. Conversely, the use of BDD led to the highest generation of ClO3- and ClO4-. The reaction mechanism was studied systematically by detecting the generated H2O2 and •OH. The initial N of CEC was released as NH4+ and, in smaller proportion, as NO3-. Four short-chain carboxylic acids and nine aromatic intermediates were also detected, a possible reaction sequence for CEC mineralization was finally proposed.

A Review: Synthesis and Applications of Titanium Sub-Oxides

Magnéli phase titanium oxides, also called titanium sub-oxides (TinO2n-1, 4 < n < 9), are a series of electrically conducting ceramic materials. The synthesis and applications of these materials have recently attracted tremendous attention because of their applications in a number of existing and emerging areas. Titanium sub-oxides are generally synthesized through the reduction of titanium dioxide using hydrogen, carbon, metals or metal hydrides as reduction agents. More recently, the synthesis of nanostructured titanium sub-oxides has been making progress through optimizing thermal reduction processes or using new titanium-containing precursors. Titanium sub-oxides have attractive properties such as electrical conductivity, corrosion resistance and optical properties. Titanium sub-oxides have played important roles in a number of areas such as conducting materials, fuel cells and organic degradation. Titanium sub-oxides also show promising applications in batteries, solar energy, coatings and electronic and optoelectronic devices. Titanium sub-oxides are expected to become more important materials in the future. In this review, the recent progress in the synthesis methods and applications of titanium sub-oxides in the existing and emerging areas are reviewed.

Sulfate Radical in (Photo)electrochemical Advanced Oxidation Processes for Water Treatment: A Versatile Approach

The search for a simple and clean approach toward the production of sulfate radicals for water treatment gave rise to electrochemical and photoelectrochemical activation techniques. The photoelectrochemical activation method does not just distinguish itself as a promising activation method, it is also used as an efficient water treatment method with the ability to treat a myriad of pollutants due to the complementary effects of highly reactive oxidizing species. This perspective highlights some merits that distinguish sulfate monoanion radicals from hydroxyl radicals. It highlights the electrochemical, photoelectrochemical, and in situ photoelectrochemical routes of generating sulfate radicals for advanced oxidation process approach to water treatment. We provide a detailed account of the few known applications of sulfate radical enhanced photoelectrochemical treatments of water laden with organics. Finally, we placed this area of research in perspective by providing outlooks and conclusive remarks.

In situ coagulation-electrochemical oxidation of leachate concentrate: A key role of cathodes

To efficiently remove organic and inorganic pollutants from leachate concentrate, an in situ coagulation-electrochemical oxidation (CO-EO) system was proposed using Ti/Ti₄O₇ anode and Al cathode, coupling the "super-Faradaic" dissolution of Al. The system was evaluated in terms of the removal efficiencies of organics, nutrients, and metals, and the underlying cathodic mechanisms were investigated compared with the Ti/RuO₂-IrO₂ and graphite cathode systems. After a 3-h treatment, the Al-cathode system removed 89.0% of COD and 36.3% of total nitrogen (TN). The TN removal was primarily ascribed to the oxidation of both ammonia and organic-N to N₂. In comparison, the Al-cathode system achieved 3-10-fold total phosphorus (TP) (62.6%) and metal removals (>80%) than Ti/RuO₂-IrO₂ and graphite systems. The increased removals of TP and metals were ascribed to the in situ coagulation of Al(OH)₃, hydroxide precipitation, and electrodeposition. With the reduced scaling on the Al cathode surface, the formation of Al³⁺ and electrified Al(OH)₃ lessened the requirement for cathode cleaning and increased the bulk conductivity, resulting in increased instantaneous current production (38.9%) and operating cost efficiencies (48.3 kWh kg_COD ^-1). The present study indicated that the in situ CO-EO process could be potentially used for treating persistent wastewater containing high levels of organic and inorganic ions.

Small-Molecule Adsorption Energy Predictions for High-Throughput Screening of Electrocatalysts

Predicting adsorption energies of small molecules (e.g., OH, OOH, CO) on electrocatalysts involved in electrochemical reactions aids in accelerating the design and screening of electrocatalysts. Avoiding computationally expensive electronic structure calculations increases the speed of such predictions. Geometric and electronic descriptors have been reported to characterize the environment around surface active sites and predict adsorption energies. However, these descriptors cannot be used to predict adsorption energies of small molecules on various substrates, e.g., metal-oxide and nonmetal electrocatalysts. We compare the performance of these descriptors in predicting adsorption energies of small molecules on various electrocatalysts with adsorption energies calculated from density functional theory. We show that two recently developed machine learning algorithms, Crystal Graph Convolutional Neural Network (CGCNN) and Atomistic Line Graph Neural Network (ALIGNN), outperform the reported descriptors based on geometric (coordination number of the active site and its nearest neighbors) and electronic (the bond-energy-integrated orbitalwise coordination number, the electronegativity, and the number of valence electrons of the active site) properties in predicting the adsorption energies. Our results suggest that ALIGNN is almost always more accurate than CGCNN in adsorption energy predictions. The improvement ranges from 0.02 to 1.0 eV in the mean absolute errors (MAEs). We also compare the performance of CGCNN and ALIGNN algorithms in predicting the overpotentials of the oxygen evolution reaction occurring on various electrocatalysts with MAEs of 0.06 and 0.05 V, respectively.

Application of Electrochemical Oxidation for Water and Wastewater Treatment: An Overview

In recent years, the discharge of various emerging pollutants, chemicals, and dyes in water and wastewater has represented one of the prominent human problems. Since water pollution is directly related to human health, highly resistant and emerging compounds in aquatic environments will pose many potential risks to the health of all living beings. Therefore, water pollution is a very acute problem that has constantly increased in recent years with the expansion of various industries. Consequently, choosing efficient and innovative wastewater treatment methods to remove contaminants is crucial. Among advanced oxidation processes, electrochemical oxidation (EO) is the most common and effective method for removing persistent pollutants from municipal and industrial wastewater. However, despite the great progress in using EO to treat real wastewater, there are still many gaps. This is due to the lack of comprehensive information on the operating parameters which affect the process and its operating costs. In this paper, among various scientific articles, the impact of operational parameters on the EO performances, a comparison between different electrochemical reactor configurations, and a report on general mechanisms of electrochemical oxidation of organic pollutants have been reported. Moreover, an evaluation of cost analysis and energy consumption requirements have also been discussed. Finally, the combination process between EO and photocatalysis (PC), called photoelectrocatalysis (PEC), has been discussed and reviewed briefly. This article shows that there is a direct relationship between important operating parameters with the amount of costs and the final removal efficiency of emerging pollutants. Optimal operating conditions can be achieved by paying special attention to reactor design, which can lead to higher efficiency and more efficient treatment. The rapid development of EO for removing emerging pollutants from impacted water and its combination with other green methods can result in more efficient approaches to face the pressing water pollution challenge. PEC proved to be a promising pollutants degradation technology, in which renewable energy sources can be adopted as a primer to perform an environmentally friendly water treatment.

Formation of polychlorinated dibenzo-p-dioxins and furans (PCDD/Fs) in the electrochemical oxidation of polluted waters with pharmaceuticals used against COVID-19

The COVID-19 pandemic has produced a huge impact on our lives, increasing the consumption of certain pharmaceuticals, and with this, contributing to the intensification of their presence in wastewater and in the environment. This situation demands the implementation of efficient remediation technologies, among them, electrochemical oxidation (ELOX) is one the most applied. This work studies the application of ELOX with the aim of eliminate pharmaceuticals used in the fight against COVID-19, assessing its degradation rate, as well as the risk of formation of toxic trace by-products, such as unintentional POPs like polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). To this end, model solutions containing 10 mg L^-1 of dexamethasone (DEX), paracetamol (PAR), amoxicillin (AMX), and sertraline (STR) with two different electrolytes (NaCl and Na₂SO₄) have been evaluated. However, electrochemical systems that contain chloride ions in solution together with PCDD/Fs precursor molecules may lead to the formation of these highly toxic by-products. So, PCDD/Fs were quantified under conditions of complete degradation of the drugs. Furthermore, the presence of PCDD/Fs precursors such as chlorophenols was determined, as well as the role of Cl^-, Cl^• and SO 4 • - radicals in the formation of the by-products and PCDD/Fs. The maximum measured concentration of PCDD/Fs was around 2700 pg L^-1 for the amoxicillin case in NaCl medium. The obtained results emphasise the importance of not underestimating the potential formation of these highly toxic trace by-products, in addition to the correct selection of oxidation processes and operation variables, in order to avoid final higher toxicity in the medium.

Energetic evaluation of phenol wastewater treatment by reverse electrodialysis reactor using different anodes

Efficient electrode materials are essential to convert salinity gradient energy into oxidative degradation energy and electrical energy by reverse electrodialysis reactor (REDR). In this context, comparative experiments of REDR using different anodes (Ti/IrO₂-RuO₂, Ti/PbO₂ and Ti/Ti₄O₇) were conducted. The effects of output current and electrode rinse solution (ERS) flowrate on mineralization efficiency and energy output were discussed. Results demonstrated that the COD removal rate(η_COD) rose almost linearly with output current and ERS flowrate when using Ti/Ti₄O₇ anode, but excessive operating conditions caused a slow increase or even decrease of η_COD when using Ti/IrO₂-RuO₂ or Ti/PbO₂ anodes. The order of electrode system potential loss (E_ele) for the three anodes was Ti/Ti₄O₇> Ti/PbO₂> Ti/IrO₂-RuO₂. High E_ele was beneficial to η_COD but had a negative effect on the net output power (P_net) of REDR. Regardless of the applied anodes, increasing the current and decreasing the ERS flowrate was detrimental to P_net due to higher E_ele. Based on these findings, four energy efficiency parameters were defined to evaluate energy recovery from multiple perspectives by linking energy output with mineralization capacity. They were electrode efficiency (η_ele), energy efficiency (EE), general current efficiency (GCE) and energy consumption (EC), respectively. Results showed that REDR with Ti/Ti₄O₇ anodes and suitable operating conditions achieved the optimal energy indicators and mineralization efficiency, which provided an efficient and economical option for wastewater treatment and energy recovery.

Wastewater treatment by anodic oxidation in electrochemical advanced oxidation process: Advance in mechanism, direct and indirect oxidation detection methods

Electrochemical Advanced Oxidation Process (EAOP) has been applied to the degradation of refractory pollutants in wastewater due to its strong oxidation capacity, high degradation efficiency, simple operation, and mild reaction. Among electrochemical processes, anodic oxidation (AO) is the most widely used and its mechanism is mainly divided into direct oxidation and indirect oxidation. Direct oxidation means that pollutants are oxidized at the anode by direct electron transfer. Indirect oxidation refers to the generation of active species during the electrolytic reaction, which acts on pollutants. The mechanism of AO process is controlled by many factors, including electrode type, electrocatalyst material, wastewater composition, pH, applied current and voltage levels. It is very important to explore the reaction mechanism of electrochemical treatment, which determines the efficiency of the reaction, the products of the reaction, and the extent of reaction. This paper firstly reviews the current research progress on the mechanism of AO process, and summarizes in detail the different mechanisms caused by influencing factors under common AO process. Then, strategies and methods to distinguish direct oxidation and indirect oxidation mechanisms are reviewed, such as intermediate product analysis, electrochemical test analysis, active species detection, theoretical calculation, and the limitations of these methods are analyzed. Finally some suggestions are put forward for the study of the mechanism of electrochemical advanced oxidation.

A review of radical and non-radical degradation of amoxicillin by using different oxidation process systems

Pharmaceutical compounds have piqued the interest of researchers due to an increase in their demand, which increases the possibility of leakage into the environment. Amoxicillin (AMX) is a penicillin derivative used for the treatment of infections caused by gram-positive bacteria. AMX has a low metabolic rate in the human body, and around 80-90% is unmetabolized. As a result, AMX residuals should be treated immediately to avoid further accumulation in the environment. Advanced oxidation process techniques are an efficient way to degrade AMX. This review attempts to collect, organize, summarize, and analyze the most up to date research linked to the degradation of AMX by different advanced oxidation process systems including photocatalytic, ultrasonic, electro-oxidation, and advanced oxidation process-based on partials. The main topics investigated in this review are degradation mechanism, degradation efficiency, catalyst stability, the formation of AMX by-products and its toxicity, in addition, the influence of different experimental conditions was discussed such as pH, temperature, scavengers, the concentration of amoxicillin, oxidants, catalyst, and doping ratio. The degradation of AMX could be inhibited by very high values of pH, temperature, AMX concentration, oxidants concentration, catalyst concentration, and doping ratio. Several AMX by-products were discovered after oxidation treatment, and several of them had lower or same values of LC₅₀ (96 h) fathead minnow of AMX itself, such as m/z 384, 375, 349, 323, 324, 321, 318, with prediction values of 0.70, 1.10, 1.10 0.42, 0.42, 0.42, and 0.42 mg/L, respectively. We revealed that there is no silver bullet system to oxidize AMX from an aqueous medium. However, it is recommended to apply hybrid systems such as Photo-electro, Photo-Fenton, Electro-Fenton, etc. Hybrid systems are capable to cover the drawbacks of the single system. This review may provide important information, as well as future recommendations, for future researchers interested in treating AMX using various AOP systems, allowing them to improve the applicability of their systems and successfully oxidize AMX from an aqueous medium.

Magnéli phase titanium sub-oxides synthesis, fabrication and its application for environmental remediation: Current status and prospect

Sub-stoichiometric titanium oxide, also called titanium suboxides (TSO), had been a focus of research for many decades with a chemical composition of Ti_nO_2n-1 (n ≥ 1). It has a unique oxygen-deficient crystal structure which provides it an outstanding electrical conductivity and high corrosion resistance similar to ceramic materials. High electrical conductivity and ability to sustain in adverse media make these phases a point of attention for researchers in energy storage and environmental remediation applications. The Magnéli phase-based reactive electroconductive membranes (REM) and electrodes have demonstrated the electrochemical oxidation of pollutants in the water in flow-through and flow by configuration. Additionally, it has also shown its potential for visible light photochemical degradation as well. This review attempts to summarize state of the art in various Magnéli phases materials synthesis routes and their electrochemical and photochemical ability for environmental application. The manuscript introduces the Magnéli phase, its crystal structure, and catalytic properties, followed by the recent development in synthesis methods from diverse titanium sources, notably TiO₂ through thermal reduction. The various fabrication methods for Magnéli phase-base REMs and electrodes have also been summarized. Furthermore, the article discussed the environmental remediations via electrochemical and photochemical advanced oxidation processes. Additionally, the hybrid technology with REMs and electrodes is used to counter membrane biofouling and develop electrochemical sensing devices for the pollutants. The Magnéli phase materials have a bright future for both electrochemical and photochemical advanced oxidation of emerging contaminants in water and wastewater treatment.

Recent development on core-shell photo(electro)catalysts for elimination of organic compounds from pharmaceutical wastewater

Pharmaceutical organics are a vital milestone in contemporary human research since they treat various diseases and improve the quality of human life. However, these organic compounds are considered one of the major environmental hazards after the conception, along with the massive rise in antimicrobial resistance (AMR) in an ecosystem. There are various biological and catalytic technologies existed to eliminate these organics in aqueous system with their limitation. Advanced Oxidation processes (AOPs) are used to decompose these pharmaceutical organic compounds in the wastewater by generating reactive species with high oxidation potential. This review focused various photocatalysts, and photocatalytic oxidation processes, especially core-shell materials for photo (electro)catalytic application in pharmaceutical wastewater decomposition. Moreover, we discussed in details about the design and recent developments of core shell catalysts and comparison for photocatalytic, electrocatalytic and photo electrocatalytic applications in pharmaceutical wastewater treatment. In addition, the mixture of inorganic and organic core-shell materials, and metal-organic framework-based core-shell catalysts discussed in detail for antibiotic degradation.

Flow-through electrochemical removal of benzotriazole by electroactive ceramic membrane

Benzotriazole (BTA) is a widely used anticorrosive additive that is of endurance, bioaccumulation and toxicity, and BTA industrial wastewater treatment remains a challenge. This study reports efficient electrochemical removal of BTA by titanium oxide (TiSO) electroactive ceramic membrane (ECM), indicated by 98.1% removal at current density of 20 mA∙cm-2 and permeate flux of 692 LHM under cathode-to-anode flow pattern (1 h). Electrochemical analysis demonstrated the pH-dependent formation of anti-corrosive BTA film on the TiSO anode, which was responsible for improved BTA removal for cathode-to-anode (CA) flow pattern compared with that for anode-to-cathode (AC). The modelling results showed the CA flow pattern to be more favourable for BTA oxidation mediated by electro-generated •OH by preventing the formation of deactivation film via creating an alkaline boundary layer at the anode/electrolyte interface. Intermediates and essential active sites were identified by using experimental analysis and theoretical density functional theory (DFT) calculations, thereby the most likely degradation pathways were underlined. Toxicity analysis revealed remarkable decrease in oral rat LD50 values and bioaccumulation factor during electrochemical degradation of BTA. This study provides a proof-in-concept demonstration of effective removal for anti-corrosive emerging pollutants by TiSO-ECM under flow-through pattern.

Hydroxyl radicals in anodic oxidation systems: generation, identification and quantification

Anodic oxidation has emerged as a promising treatment technology for the removal of a broad range of organic pollutants from wastewaters. Hydroxyl radicals are the primary species generated in anodic oxidation systems to oxidize organics. In this review, the methods of identifying hydroxyl radicals and the existing debates and misunderstandings regarding the validity of experimental results are discussed. Consideration is given to the methods of quantification of hydroxyl radicals in anodic oxidation systems with particular attention to approaches used to compare the electrochemical performance of different anodes. In addition, we describe recent progress in understanding the mechanisms of hydroxyl radical generation at the surface of most commonly used anodes and the utilization of hydroxyl radical in typical electrochemical reactors. This review shows that the key challenges facing anodic oxidation technology are related to i) the elimination of mistakes in identifying hydroxyl radicals, ii) the establishment of an effective hydroxyl radical quantification method, iii) the development of cost effective anode materials with high corrosion resistance and high electrochemical activity and iv) the optimization of electrochemical reactor design to maximise the utilization efficiency of hydroxyl radicals.

Progress in Preparation and Application of Titanium Sub-Oxides Electrode in Electrocatalytic Degradation for Wastewater Treatment

To achieve low-carbon and sustainable development it is imperative to explore water treatment technologies in a carbon-neutral model. Because of its advantages of high efficiency, low consumption, and no secondary pollution, electrocatalytic oxidation technology has attracted increasing attention in tackling the challenges of organic wastewater treatment. The performance of an electrocatalytic oxidation system depends mainly on the properties of electrodes materials. Compared with the instability of graphite electrodes, the high expenditure of noble metal electrodes and boron-doped diamond electrodes, and the hidden dangers of titanium-based metal oxide electrodes, a titanium sub-oxide material has been characterized as an ideal choice of anode material due to its unique crystal and electronic structure, including high conductivity, decent catalytic activity, intense physical and chemical stability, corrosion resistance, low cost, and long service life, etc. This paper systematically reviews the electrode preparation technology of Magnéli phase titanium sub-oxide and its research progress in the electrochemical advanced oxidation treatment of organic wastewater in recent years, with technical difficulties highlighted. Future research directions are further proposed in process optimization, material modification, and application expansion. It is worth noting that Magnéli phase titanium sub-oxides have played very important roles in organic degradation. There is no doubt that titanium sub-oxides will become indispensable materials in the future.

Interface engineering strategy of a Ti4O7 ceramic membrane via graphene oxide nanoparticles toward efficient electrooxidation of 1,4-dioxane

Although Ti₄O₇ ceramic membrane has been recognized as one of the most promising anode materials for electrochemical advanced oxidation process (EAOP), it suffers from relatively low hydroxyl radical (^•OH) production rate and high charge-transfer resistance that restricted its oxidation performance of organic pollutants. Herein, we reported an effective interface engineering strategy to develop a Ti₄O₇ reactive electrochemical membrane (REM) doped by graphene oxide nanoparticles (GONs), GONs@Ti₄O₇ REM, via strong GONs-O-Ti bonds. Results showed that 1% (wt%) GON doping on Ti₄O₇ REM significantly reduced the charge-transfer resistance from 73.87 to 8.42 Ω compared with the pristine Ti₄O₇ REM, and yielded ^•OH at 2.5-2.8 times higher rate. The 1,4-dioxane (1,4-D) oxidation rate in batch experiments by 1%GONs@Ti₄O₇ REM was 1.49×10^-2 min^-1, 2 times higher than that of the pristine Ti₄O₇ REM (7.51×10^-3 min^-1) and similar to that of BDD (1.79×10^-2 min^-1). The 1%GONs@Ti₄O₇ REM exhibited high stability after a polarization test of 90 h at 80 mA/cm², and within 15 consecutive cycles, its oxidation performance was stable (95.1-99.2%) with about 1% of GONs lost on the REM. In addition, REM process can efficiently degrade refractory organic matters in the groundwater and landfill leachate, the total organic carbon was removed by 54.5% with a single-pass REM. A normalized electric energy consumption per log removal of 1,4-D (EE/O) was observed at only 0.2-0.6 kWh/m³. Our results suggested that chemical-bonded interface engineering strategy using GONs can facilitate the EAOP performance of Ti₄O₇ ceramic membrane with outstanding reactivity and stability.

Upcycling to Sustainably Reuse Plastics

Plastics are now indispensable in daily lives. However, the pollution from plastics is also increasingly becoming a serious environmental issue. Recent years have seen more sustainable approaches and technologies, commonly known as upcycling, to transform plastics into value-added materials and chemical feedstocks. In this review, the latest research on upcycling is presented, with a greater focus on the use of renewable energy as well as the more selective methods to repurpose synthetic polymers. First, thermal upcycling approaches are briefly introduced, including the redeployment of plastics for construction uses, 3D printing precursors, and lightweight materials. Then, some of the latest novel strategies to deconstruct condensation polymers to monomers for repolymerization or introduce vulnerable linkers to make the plastics more degradable are discussed. Subsequently, the review will explore the breakthroughs in plastics upcycling by heterogeneous and homogeneous photocatalysis, as well as electrocatalysis, which transform plastics into more versatile fine chemicals and materials while simultaneously mitigating global climate change. In addition, some of the biotechnological advances in the discovery and engineering of microbes that can decompose plastics are also presented. Finally, the current challenges and outlook for future plastics upcycling are discussed to stimulate global cooperation in this field.

Electrocatalytic oxidation of aromatic amine (4-aminobiphenyl): Kinetics and transformation products with mechanistic approach

Electrocatalytic oxidation (EO) of carcinogenic 4-aminobiphenyl (4-ABP) aromatic amine was performed using Ti-RuO₂ anodes. Current (I), pH, electrolysis time (t), and 4-ABP initial concentration (C_o ) were selected as EO parameters, and their effects on %4-ABP removal (R₁ ) and energy consumed (R₂ ) were studied. Experimental design, parameters optimization, and their interaction with responses R₁ and R₂ were performed using response surface methodology. At optimized parameters, %TOC removal and 4-BP mineralization current efficiency (%MCE) were assessed to evaluate the potential of Ti/RuO₂ anodes towards 4-ABP mineralization. Simultaneous TOC and 4-ABP degradation kinetics were also studied to evaluate the competition in 4-ABP mineralization and degradation. Further, UPLC-Q-TOF-MS analysis was performed to identify the 4-ABP transformation products during the EO, and a mechanism describing the EO transformation was proposed. At optimum parameters (I = 1.2 A; pH = 4.0; t = 30 min; C_o  = 30 ppm), responses were found to be R₁  = 60.25%; R₂  = 2.49 kWh/g of 4-ABP removed. %TOC removal and %MCE were 52.4% and 34.2%, respectively. PRACTITIONER POINTS: 4-Aminobiphenyl electro-oxidation (EO) was explored using Ti/RuO₂ anode. Achieved 34.2% mineralization current efficiency, 52.4% TOC and 61.3% TKN removal. Three electro-oxidation transformation products of 4-ABP were detected. 4-Aminobiphenyl was found degrading at ≈1.6 times higher rate than TOC A plausible EO transformation pathway and mechanism was proposed.

Exploration of perfluorooctane sulfonate degradation properties and mechanism via electron-transfer dominated radical process

Polyfluoroalkyl and perfluoroalkyl chemicals (PFCs) widely used in lubricants, surfactant, textiles, paper coatings, cosmetics, and fire-fighting foams can release a large deal of organics contaminants into wastewater and pose great risks to the health of humans and eco-environments. Although advanced oxidation processes can effectively deconstruct various organic contaminants via reactive radicals, the stable structure of PFCs makes it difficult to be degraded. Here, we confirm that electrochemical oxidation process coupled with peroxymonosulfate (PMS) reaction can efficiently destroy stable structure of PFCs via electron transfer and meanwhile completely degrade PFCs via generated active radicals. We further studies via capturing and scavenging radicals, and DFT calculations find that electron hydroxyl radials play a dominant role in degrading PFCs. Based on the calculations of adsorption energy and molecular orbital energy we further demonstrate that many active sites on the surface of Ti₄O₇ (1 0 4) plane can rapidly take part in electrochemical reaction for generating radials and removing organic contaminants. These results give a promising insight towards high-effective and deep degradation of PFCs via electrochemical reaction coupled with advanced oxidation processes, as well as providing guidance and technical support for the remove of multiple organic contaminants.

Enhanced electro-oxidation performance of FeCoLDH to organic pollutants using hydrophilic structure

Iron-cobalt layered double hydroxides (FeCoLDH) showed superior oxygen evolution reaction (OER) performance, but the sluggish water adsorption and dissociation dynamics restrict its capacity to degrade organic pollutants by electro-oxidation. Herein, enhanced electro-oxidation performance of FeCoLDH with hydrophilic structure was designed and exhibited efficient removal efficiency of tetracycline. Theoretical calculation and characterization results consistently elucidated that the electronic structure of FeCoLDH is optimized by doping phosphorus and depositing copper nanodots (NDs). In addition, the obtained Cu NDs/P-FeCoLDH shows higher degradation ability of tetracycline in all-pH conditions than pristine FeCoLDH. That's because it owns smaller barrier with 0.6 eV to generate hydroxyl radicals (•OH) than pristine FeCoLDH. Furthermore, it can effectively degrade organic pollutants in seawater, river water and pharmaceutical wastewater samples. This work provides novel and rational electrode materials for electro-oxidation system with practical application potential, which could offer new insights into the fundamental understanding of electrochemistry.

Treatment of organic wastewater by a synergic electrocatalysis process with Ti3+ self-doped TiO2 nanotube arrays electrode as both cathode and anode

Electrochemical anodic oxidation (AO) is a promising technology for wastewater treatment due to its strong oxidation property and environmental compatibility. However, it suffers from high energy consumption for pollutants removal due to the side-reactions of hydrogen evolution reaction on cathode and oxygen evolution reaction on anode. Combining electro-Fenton (EF) with AO not only generated •OH for pollutants degradation but also increased current efficiency. This work investigated a synergic electrocatalysis process between EF and AO with Ti³⁺ self-doped TiO₂ nanotube arrays (Ti³⁺/TNTAs) electrode as both cathode and anode for wastewater treatment. The pseudo-first-order kinetic rate constant of phenol degradation by EF+AO (0.107 min^-1) was 9.7 or 6.3 times as much as that of only EF (0.011 min^-1) or AO (0.017 min^-1) process, respectively. Enhanced pollutants removal of EF+AO could be attributed to the coexistence of •OH oxidation and direct oxidation on Ti³⁺/TNTAs surface. The COD of secondary effluent of coking wastewater decreased from 159.3 mg L^-1 to 47.0 mg L^-1 by EF+AO within 120 min with low specific energy consumption (9.5 kWh kg^-1 COD^-1). This work provided a new insight into design of the energy-efficient synergic electrocatalysis process for refractory pollutants degradation.

Fabrication and Characterization of the Porous Ti4O7 Reactive Electrochemical Membrane

Preparation of the Magnéli Ti₄O₇ reactive electrochemical membrane (REM) with high purity is of great significance for its application in electrochemical advanced oxidation processes (EAOPs) for wastewater treatment. In this study, the Ti₄O₇ REM with high purity was synthesized by mechanical pressing of TiO₂ powders followed by thermal reduction to Ti₄O₇ using the Ti powder as the reducing reagent, where the TiO₂ monolith and Ti powder were separated from each other with the distance of about 5 cm in the vacuum furnace. When the temperature was elevated to 1333 K, the Magnéli phase Ti₄O₇ REM with the Ti₄O₇ content of 98.5% was obtained after thermal reduction for 4 h. Noticeably, the surface and interior of the obtained REM bulk sample has a homogeneous Ti₄O₇ content. Doping carbon black (0wt%-15wt%) could increase the porosity of the Ti₄O₇ REM (38–59%). Accordingly, the internal resistance of the electrode and electrolyte and the charge-transfer impedance increased slightly with the increasing carbon black content. The optimum electroactive surface area (1.1 m²) was obtained at a carbon black content of 5wt%, which increased by 1.3-fold in comparison with that without carbon black. The as-prepared Ti₄O₇ REMs show high oxygen evolution potential, approximately 2.7 V/SHE, indicating their appreciable electrocatalytic activity toward the production of •OH.

How to Build a Microplastics-Free Environment: Strategies for Microplastics Degradation and Plastics Recycling

Microplastics are an emergent yet critical issue for the environment because of high degradation resistance and bioaccumulation. Unfortunately, the current technologies to remove, recycle, or degrade microplastics are insufficient for complete elimination. In addition, the fragmentation and degradation of mismanaged plastic wastes in environment have recently been identified as a significant source of microplastics. Thus, the developments of effective microplastics removal methods, as well as, plastics recycling strategies are crucial to build a microplastics-free environment. Herein, this review comprehensively summarizes the current technologies for eliminating microplastics from the environment and highlights two key aspects to achieve this goal: 1) Catalytic degradation of microplastics into environmentally friendly organics (carbon dioxide and water); 2) catalytic recycling and upcycling plastic wastes into monomers, fuels, and valorized chemicals. The mechanisms, catalysts, feasibility, and challenges of these methods are also discussed. Novel catalytic methods such as, photocatalysis, advanced oxidation process, and biotechnology are promising and eco-friendly candidates to transform microplastics and plastic wastes into environmentally benign and valuable products. In the future, more effort is encouraged to develop eco-friendly methods for the catalytic conversion of plastics into valuable products with high efficiency, high product selectivity, and low cost under mild conditions.

Electrochemical study of a novel high-efficiency PbO2 anode based on a cerium-graphene oxide co-doping strategy: Electrodeposition mechanism, parameter optimization, and degradation pathways

A novel and efficient Ti/SnO₂-Sb/PbO₂-GO-Ce electrode was successfully fabricated based on the co-deposition of Ce ions and graphene oxide (GO) into β-PbO₂ crystals and used as an anode for electrocatalytic oxidation of phenol. The electrodeposition mechanism, parameter optimization, mechanism analysis, and potential degradation pathways were discussed in depth. The co-doping of GO and Ce resulted in the high directional specificity of β(301), orderly and dense grain arrangement of PbO₂ crystals. At the same time, the oxygen evolution potential, •OH generation capacity and lifetime were also improved. The effects of experimental parameters on phenol removal efficiency were evaluated, including the applied current density, electrode gap, supporting electrolyte, initial NaCl concentration, initial pH, and initial phenol concentration. Under the optimal conditions, the removal efficiency of phenol can reach 375.6 g m^-2 h^-1 for 20 min electrolysis, which is about 1.2 times that of the pure PbO₂ electrode. The active oxygen species (•OH, ClO^- and HClO) were important attributes to the degradation of phenol. Additionally, a potential degradation pathway for phenol was proposed. After 10 successive recycles, there was no significant difference of the electro-generated •OH, cell voltage and phenol removal rate, which confirms the stability and admirable reusability of Ti/SnO₂-Sb/PbO₂-GO-Ce electrode.

Elimination of amoxicillin using zeolite Y-sea salt as a good catalyst for activation of hydrogen peroxide: Investigating degradation pathway and the effect of wastewater chemistry

The sea contains elements that can play a useful role in catalyzing reactions. Therefore, this research was done to focus on eliminating amoxicillin (AMX) from wastewater utilizing zeolite Y- sea salt catalyst in the presence of H₂O₂. The influences of furnace temperature (200-500 °C) and time duration in the furnace (1-4 h) were optimized during catalyst generation. Also, the effects of different parameters on AMX removal, such as pH (5.0-9.0), catalyst dose (0-10 g.L^-1), AMX concentration (50-300 mg.L^-1), contact time (10-130 min), and H₂O₂ concentration (0-6 mL/100 mL distilled water) were investigated. Different analyses like Brunauer-Emmett-Teller (BET), Fourier transform infrared (FTIR), X-ray diffraction (XRD), and thermogravimetric analysis (TGA) were conducted to reveal catalyst properties. The BET-specific surface area of the catalyst (12.69 m²g^-1) insignificantly (p-value > 0.05) changed after AMX removal (13.04 m²g^-1), indicating the strength of the prepared catalyst. The active groups of N-H, O-H-O, O-Si-O, C-H, Si-O-Si, and Si-O-Al were determined in the catalyst structure. The highest removal of AMX (93%) was achieved in the zeolite-sea salt/H₂O₂ system at a pH level of 6.0 and an H₂O₂ concentration of 0.1 mL/100 mL. Elimination of the AMX followed pseudo-first-order kinetics. The catalyst was reclaimed up to 7 times and the removal efficiency was suitable up to the fifth stage. The by-products and reaction pathways were investigated by gas chromatography-mass spectrometry (GC-MS). The results showed that zeolite-sea salt can be utilized as an H₂O₂ activator for the effective degradation of AMX from wastewater.