Reaction pathways and mechanisms of photodegradation of pesticides

Rethinking alternatives to fluorinated pops in aqueous environment and corresponding destructive treatment strategies

Alternatives are being developed to replace fluorinated persistent organic pollutants (POPs) listed in the Stockholm Convention, bypass environmental regulations, and overcome environmental risks. However, the extensive usage of fluorinated POPs alternatives has revealed potential risks such as high exposure levels, long-range transport properties, and physiological toxicity. Therefore, it is imperative to rethink the alternatives and their treatment technologies. This review aims to consider the existing destructive technologies for completely eliminating fluorinated POPs alternatives from the earth based on the updated classification and risks overview. Herein, the types of common alternatives were renewed and categorized, and their risks to the environment and organisms were concluded. The efficiency, effectiveness, energy utilization, sustainability, and cost of various degradation technologies in the treatment of fluorinated POPs alternatives were reviewed and evaluated. Meanwhile, the reaction mechanisms of different fluorinated POPs alternatives are systematically generalized, and the correlation between the structure of alternatives and the degradation characteristics was discussed, providing mechanistic insights for their removal from the environment. Overall, the review supplies a theoretical foundation and reference for the control and treatment of fluorinated POPs alternatives pollution.

Photodegradation of the novel herbicide pyraclonil in aqueous solution: Kinetics, identification of photoproducts, mechanism, and toxicity assessment

Pyraclonil is a new type of pyrazole herbicide, whose photochemical fate in aqueous solution has not been reported yet. In this study, effects on the photolysis rate such as light source, pH, NO3-, Fe3+, fulvic acid (FA) and riboflavin (RF) were investigated. Pyraclonil photodegraded in pure water under both UV and simulated sunlight with half-lives of 32.29 min and 42.52 h, respectively. Under UV, the degradation rate of pyraclonil in pH 4 solution (0.0299 ± 0.0033 min-1) was about twice higher than that in pH 9 (0.0160 ± 0.0063 min-1). Under simulated sunlight, low concentration (0.1-1 mg/L) of FA, NO3-, Fe3+ and RF noticeably promoted the photodegradation of pyraclonil. Then, with the combination of experimental UPLC-Q-TOF/MS and computational calculation of density functional theory (DFT), fourteen transformation products (TPs) of pyraclonil were identified with possible mechanism of C-N bond cleavage, photorearrangement, demethylation, hydroxylation and oxidation. Additionally, acute toxicity assessment was conducted through ECOSAR prediction and laboratory bioassays. The prediction results indicated that toxicity of TP157 to daphnid and green algae was 1.3 and 1.4 times higher than that of the parent, respectively. The bioassay results indicated that toxicities of TP157 and TP263 to C. vulgaris were about 1.6 and 5.9 times higher than that of the parent, respectively. The results provided a reference for elucidating the potential hazards of pyraclonil to non-target organisms and promoting its rational use.

Effect of tannic acid binding on the thermal degradation behavior and product toxicity of boscalid

The effect of tannic acid (TA) binding on the thermal degradation of boscalid was studied in this work. The results revealed that TA binding has a significant impact on boscalid degradation. The degradation rate constant of bound boscalid was reduced, and its corresponding half-life was significantly prolonged compared to the free state. Four identical degradation products were detected in both states through UHPLC-Q-TOF-MS, indicating that degradation products were not affected by TA binding. Based on DFT and MS analysis, the degradation pathways of boscalid included hydroxyl substitution of chlorine atoms and cleavage of CN and CC bonds. The toxicity of B2 and B3 exceeded that of boscalid. In summary, the binding of TA and boscalid significantly affected the thermal degradation rate of boscalid while preserving the types of degradation products. This study contributed to a fundamental understanding of the degradation process of bound pesticide residues in complex food matrices.

Epoxiconazole degradation in water samples: a comparative study of Fenton, photo-Fenton, solar photo-Fenton, and solar photolysis processes

Epoxiconazole (EPO) is classified as a persistent organic pollutant due to its ability to persist in the environment for prolonged periods. Its degradation is pivotal in mitigating its environmental impact. This investigation focuses on assessing the degradation of EPO using various methodologies, namely Fenton, photo-Fenton, solar photo-Fenton, and solar photolysis, conducted in both Milli-Q water and groundwater. These experiments encompassed evaluations at both the standard pH typically used in photo-Fenton reactions and the natural pH levels inherent to the respective aqueous environments. Additionally, EPO degradation products were analyzed after a 60-min reaction. Notably, in systems utilizing groundwater, the inclusion of additional iron was unnecessary, as the naturally occurring iron content in the groundwater facilitated the intended processes. Specifically, in Milli-Q water, solar photo-Fenton demonstrated an EPO degradation efficiency of 97%. Furthermore, the substitution of Milli-Q water with groundwater in Fenton-like processes did not significantly affect the efficacy of EPO degradation. These findings underscore the potential of solar photo-Fenton as an economically viable and environmentally sustainable strategy for EPO degradation.

The Fabrication and Property Characterization of a Ho2YSbO7/Bi2MoO6 Heterojunction Photocatalyst and the Application of the Photodegradation of Diuron under Visible Light Irradiation

A novel photocatalytic nanomaterial, Ho2YSbO7, was successfully synthesized for the first time using the solvothermal synthesis technique. In addition, a Ho2YSbO7/Bi2MoO6 heterojunction photocatalyst (HBHP) was prepared via the hydrothermal fabrication technique. Extensive characterizations of the synthesized samples were conducted using various instruments, such as an X-ray diffractometer, a Fourier transform infrared spectrometer, a Raman spectrometer, a UV-visible spectrophotometer, an X-ray photoelectron spectrometer, and a transmission electron microscope, as well as X-ray energy dispersive spectroscopy, photoluminescence spectroscopy, a photocurrent test, electrochemical impedance spectroscopy, ultraviolet photoelectron spectroscopy, and electron paramagnetic resonance. The photocatalytic activity of the HBHP was evaluated for the degradation of diuron (DRN) and the mineralization of total organic carbon (TOC) under visible light exposure for 152 min. Remarkable removal efficiencies were achieved, with 99.78% for DRN and 97.19% for TOC. Comparative analysis demonstrated that the HBHP exhibited markedly higher removal efficiencies for DRN compared to Ho2YSbO7, Bi2MoO6, or N-doped TiO2 photocatalyst, with removal efficiencies 1.13 times, 1.21 times, or 2.95 times higher, respectively. Similarly, the HBHP demonstrated significantly higher removal efficiencies for TOC compared to Ho2YSbO7, Bi2MoO6, or N-doped TiO2 photocatalyst, with removal efficiencies 1.17 times, 1.25 times, or 3.39 times higher, respectively. Furthermore, the HBHP demonstrated excellent stability and reusability. The mechanisms which could enhance the photocatalytic activity remarkably and the involvement of the major active species were comprehensively discussed, with superoxide radicals identified as the primary active species, followed by hydroxyl radicals and holes. The results of this study contribute to the advancement of efficient heterostructural materials and offer valuable insights into the development of sustainable remediation strategies for addressing DRN contamination.

Photolysis of dinotefuran in aqueous solution: Kinetics, influencing factors and photodegradation mechanism

The environmental behaviour of neonicotinoid insecticides (NNIs) is of momentous concern due to their frequent detection in aquatic environment and their biotoxicity for non-target organisms. Phototransformation is one of the most significant transformation processes, which is directly related to NNIs exposure and environmental risks. In this study, the photodegradation of dinotefuran (DIN, 1-Methyl-2-nitro-3-(tetrahydro-3-furanylmethyl)-guanidine), one of the most promising NNIs, was conducted under irritated light in the presence of Cl-, DOM along with the effect of pH and initial concentration. The findings demonstrated that in ultra-pure (UP) water, the photolysis rate constants (k) of DIN rose with increasing initial concentration. Whereas, in tap water, at varied pH levels, and in the presence of Cl-, the outcomes were reversed. At the same time, lower concentration of DOM promoted DIN photolysis processes due to the production of reactive oxygen species, while higher concentrations of DOM inhibited the photolysis by the predominance of light shielding effects. The singlet oxygen (1O2) was produced in the photolysis processes of DIN with Cl- and DOM, which was confirmed by electron spin resonance (EPR) analysis. Four main photolysis products and three intermediates were identified by UPLC-Q-Exactive Orbitrap MS analysis. The possible photodegradation pathways of DIN were proposed including the oxidation by 1O2, reduction and hydrolysis after the removal of nitro group from parent compounds. This study expanding our understanding of transformation behavior and fate of NNIs in the aquatic environment, which is essential for estimating their environmental risks.

Influence of pesticide mixture on their heterogeneous atmospheric degradation by ozone and OH radicals

Pesticides in the atmosphere can exist in both gaseous and particulate phases due to their semi-volatile properties. They can undergo degradation when exposed to atmospheric oxidants like ozone and hydroxyl radicals. The majority of studies on the atmospheric reactivity of pesticides study them in combination, without considering potential mixture effects that could induce uncertainties in the results. Therefore, this study aims to address this gap, through laboratory studies using a flow reactor, and by evaluating the degradation kinetics of pendimethalin mixed with folpet, tebuconazole, and S-metolachlor, which were simultaneously adsorbed on hydrophobic silica particles that mimic atmospheric aerosols. The comparison with other mixtures, including pendimethalin, from the literature has shown similar reactivity with ozone and hydroxyl radicals, indicating that the degradation kinetics of pesticides is independent of the mixture. Moreover, the degradation rates of the four pesticides under study indicate that they are not or slightly degraded by ozone, with half-lives ranging from 29 days to over 800 days. In contrast, when exposed to hydroxyl radicals, tebuconazole exhibited the fastest reactivity, with a half-life of 4 days, while pendimethalin had a half-life of 17 days.

Effluent toxicity study using biomarkers for ciprofloxacin photoelectrocatalytic degradation by bismuth-doped titanium dioxide nanotubes

Ciprofloxacin hydrochloride (CIP) is a broad-spectrum synthetic antibiotic often found in domestic sewage and industrial waste due to the inefficiency of conventional treatments. Given the potential risk of drug accumulation, this study presents coatings of titanium dioxide nanotubes (TiO2) doped with different bismuth (Bi) concentrations to degrade CIP through photocatalytic and photoelectrochemical processes. Characterization studies revealed that bismuth (Bi) doping affected the morphology of the materials, with concentrations of 0.01 and 0.05 mol L-1, resulting in collapsed materials with a smaller active surface area. Photocatalysis tests for all the materials exhibited a similar degree of efficiency to photolysis, approximately 33%. Ecotoxicity tests using the biomarkers Lactuca sativa L., Lemna minor, and Artemia salina indicated that, although they were similar to photolysis in terms of efficiency, the effluents generated when employing the doped catalysts showed lower levels of toxicity, with the best results achieved for the material doped with 0.005 mol L-1 of Bi, with a toxicity level approximately 40% lower. Photoelectrocatalysis proved to be the most efficient CIP degradation technique. The highest degradation rate was observed for materials doped with 0.005 mol L-1 of Bi, with an efficiency of 46%, which is 1.4 times more efficient than photolysis. These results demonstrate that materials doped with low amounts of Bi can be effectively used as photoanodes for drug degradation, as their performance is superior, and the final product generated exhibits low toxicity to living organisms.

Biodegradation mechanism of chlorpyrifos by Bacillus sp. H27: Degradation enzymes, products, pathways and whole genome sequencing analysis

Chlorpyrifos (CP) is a pesticide widely used in agricultural production. However, excessive use of CP is risky for human health and the ecological environment. Microbial remediation has become a research hotspot of environmental pollution control. In this study, the effective CP-degrading strain H27 (Bacillus cereus) was screened from farmland soil, and the degradation ratio was more than 80%. Then, the degradation mechanism was discussed in terms of enzymes, pathways, products and genes, and the mechanism was improved in terms of cell motility, secretory transport system and biofilm formation. The key CP-degrading enzymes were mainly intracellular enzymes (IE), and the degradation ratio reached 49.6% within 30 min. The optimal pH for IE was 7.0, and the optimal temperature was 25 °C. Using DFT and HPLC‒MS analysis, it was found that degradation mainly involved oxidation, hydrolysis and other reactions, and 3 degradation pathways and 14 products were identified, among which TCP (3,5,6-trichloro-2-pyridinol) was the main primary degradation product in addition to small molecules such as CO2 and H2O. Finally, the whole genome of strain H27 was sequenced, and the related degrading genes and enzymes were investigated to improve the metabolic pathways. Strain H27 had perfect genes related to flagellar assembly and chemotaxis and tended to tolerate CP. Moreover, it can secrete esterase, phosphatase and other substances, which can form biofilms and degrade CP in the environment. In addition, CP enters the cell under the action of permeases or transporters, and it is metabolized by IE. The degradation mechanism of CP by strain H27 is speculated in this study, which provided a theoretical basis for enriching CP-degrading bacteria resources, improving degradation metabolic pathways and mechanisms, and applying strain H27 to environmental pollution remediation.

Impact of ultraviolet-absorbing 2-hydroxy-4-quaternaryammoniumalkoxy benzophenone motif on photodegradation of disulfoton: a case study

Pesticide deposits post-treatment and before diffusing inside the plants are exposed to sunlight. Many of them degrade into a variety of photoproducts that may be harmful to living beings through accidental ingestion. The addition of ultraviolet light absorbers to the pesticide formulations is an attractive strategy to prevent photodegradation of the pesticides. Water-soluble quaternary ammonium ultraviolet light absorbers (QAUVAs) were synthesized from 2,4-dihydroxy benzophenones (BP-1) and their structures were confirmed by 1H NMR, 13C NMR, UV, and FTIR. A cost-saving approach for the photoprotection of disulfoton insecticide using these QAUVAs is presented. All the four QAUVAs exhibit excellent UV screening effect. The insecticide disulfoton was recovered in much higher amounts (22.27 ~ 25.64% higher than control) when it was irradiated in the presence of QAUVAs in comparison with the amount of recovery of pesticide exposed in absence of them.

Degradation of Pesticides Using Semiconducting and Tetrapyrrolic Macrocyclic Photocatalysts-A Concise Review

Exposure to pesticides is inevitable in modern times, and their environmental presence is strongly associated to the development of various malignancies. This challenge has prompted an increased interest in finding more sustainable ways of degrading pesticides. Advanced oxidation processes in particular appear as highly advantageous, due to their ability of selectively removing chemical entities form wastewaters. This review provides a concise introduction to the mechanisms of photochemical advanced oxidation processes with an objective perspective, followed by a succinct literature review on the photodegradation of pesticides utilizing metal oxide-based semiconductors as photosensitizing catalysts. The selection of reports discussed here is based on relevance and impact, which are recognized globally, ensuring rigorous scrutiny. Finally, this literature review explores the use of tetrapyrrolic macrocyclic photosensitizers in pesticide photodegradation, analyzing their benefits and limitations and providing insights into future directions.

Advanced electrocatalytic redox processes for environmental remediation of halogenated organic water pollutants

Halogenated organic compounds are widespread, and decades of heavy use have resulted in global bioaccumulation and contamination of the environment, including water sources. Here, we introduce the most common halogenated organic water pollutants, their classification by type of halogen (fluorine, chlorine, or bromine), important policies and regulations, main applications, and environmental and human health risks. Remediation techniques are outlined with particular emphasis on carbon-halogen bond strengths. Aqueous advanced redox processes are discussed, highlighting mechanistic details, including electrochemical oxidations and reductions of the water-oxygen system, and thermodynamic potentials, protonation states, and lifetimes of radicals and reactive oxygen species in aqueous electrolytes at different pH conditions. The state of the art of aqueous advanced redox processes for brominated, chlorinated, and fluorinated organic compounds is presented, along with reported mechanisms for aqueous destruction of select PFAS (per- and polyfluoroalkyl substances). Future research directions for aqueous electrocatalytic destruction of organohalogens are identified, emphasizing the crucial need for developing a quantitative mechanistic understanding of degradation pathways, the improvement of analytical detection methods for organohalogens and transient species during advanced redox processes, and the development of new catalysts and processes that are globally scalable.

Effect of ultraviolet radiation on immature stages of Aedes aegypti, Anopheles stephensi and Culex quinquefasciatus mosquitoes

Background & objectives

Understanding the influence of ultraviolet light on organisms is important for examining the hazards of exposure to ultraviolet (UV) light. However, little is known about the biological toxicity of ultraviolet light against mosquitoes, which are regularly exposed to UV light. This study was planned to determine the impact of UV radiation on different aquatic stages of Aedes aegypti, Anopheles stephensi and Culex quinquefaciatus mosquitoes.

Methods

We exposed I/II instar larvae, III/IV instar larvae and pupae of Ae. aegypti, An. stephensi and Cx. quinquefaciatus mosquitoes to UV radiation of 253 nm wavelength in a closed chamber of 30×30 cm. The exposure was done for different time intervals viz. 1, 2, 3, 4 minutes and so on. Development of larvae/pupae to adult stage was monitored daily and mortality, if any, was recorded.

Results

Development of I/II instar larvae of Ae. aegypti and Cx. quinquefasciatus to pupal stage was unsuccessful at an exposure time of one minute while only 1.7% pupation occurred in I/II instar larvae of Ae. aegypti upon similar exposure. When III/IV stage larvae were exposed to UV light, pupal development occurred only at 30seconds and one-minute exposure in An. stephensi and Cx. quinquefaciatus but in Ae. aegypti, no pupation occurred with one-minute exposure. With four-minute UV exposure of pupae, no adult emerged in Ae. aegypti; 33.3% adult emerged in An. stephensi and 66.7% adult emerged in Cx. quinquefaciatus.

Interpretation & conclusion

Our results show that UV radiation results in developmental arrest of Ae. aegypti, An. stephensi and Cx. quinquefaciatus mosquitoes.

Measuring the photostability of agrochemicals on leaves: understanding the balance between loss processes and foliar uptake

BACKGROUND

Photostability is an important property in agrochemicals, impacting their biological efficacy, environmental fate and registrability. As such, it is a property that is routinely measured during the development of new active ingredients and their formulations. To make these measurements, compounds are typically exposed to simulated sunlight after application to a glass substrate. While useful, these measurements neglect key factors that influence photostability under true field conditions. Most importantly, they neglect the fact that compounds are applied to living plant tissue, and that uptake and movement within this tissue provides a mechanism to protect compounds from photodegradation.

RESULTS

In this work, we introduce a new photostability assay incorporating leaf tissue as a substrate, designed to run at medium throughput under standardized laboratory conditions. Using three test cases, we demonstrate that our leaf-disc-based assays provides quantitatively different photochemical loss profiles to an assay employing a glass substrate. And we also demonstrate that these different loss profiles are intimately linked to the physical properties of the compounds, the effect that those properties have on foliar uptake and, thereby, the availability of the active ingredient on the leaf surface.

CONCLUSIONS

The method presented provides a quick and simple measure of the interplay between abiotic loss processes and foliar uptake, supplying additional information to facilitate the interpretation of biological efficacy data. The comparison of loss between glass slides and leaves also provides a better understanding of when intrinsic photodegradation is likely to be a good model for a compound's behaviour under field conditions. © 2023 Society of Chemical Industry.

Photolysis mechanism of eleven insecticides under simulated sunlight irradiation: Kinetics, pathway and QSAR

Insecticides are widely used in crop protection against insects and frequently detected in aquatic environment. Photolysis kinetics are directly related with exposure assessment and risk assessment. However, the photolysis mechanism of neonicotinoid insecticides with different structures has not been studied and compared systematically in the literature. In this paper, the photolysis rate constants in water were determined for eleven insecticides under irradiation of simulated sunlight. At the same time, the photolysis mechanism and effect of dissolved organic matter (DOM) on their photolysis were studied. The results showed that photolysis rates of eleven insecticides vary in a large range. The photolysis rates of nitro-substituted neonicotinoids and butenolide insecticide are much faster than that of cyanoimino-substituted neonicotinoids and sulfoximine insecticide. The ROS scavenging activity assays reveal that direct photolysis dominates the degradation of seven insecticides and, on the other hand, self-sensitized photolysis dominates four insecticides. The shading-effect from DOM can reduce the direct photolysis rates, on the other hand, ROSs generated by triplet-state DOM (³DOM*) can also accelerate photolysis of insecticides. According to the photolytic products identified from HPLC-MS, these eleven insecticides have different photolysis pathways. Six insecticides are degraded from the removal of nitro group from their parent compounds and four insecticides are degraded through ·OH reaction or singlet oxygen (¹O₂) reaction. QSAR (quantitative structure-activity relationship) analysis showed that photolysis rate was directly related to the energy gap between the highest occupied molecular orbital to the lowest unfilled molecular orbital (E_gap = E_LUMO-E_HOMO) and dipole moment (δ). These two descriptors reflect the chemical stability and reactivity of insecticides. The pathways developed from identified products and the molecular descriptors of QSAR models can well verify the photolysis mechanisms of eleven insecticides.

Comparison of plasma technology for the study of herbicide degradation

The study aimed to investigate the effects of two different plasma systems, including pinhole plasma jet and gliding arc (GA) plasma, for the degradation of herbicide, diuron, in plasma activated solutions (PAS). In the GA plasma system, air was used to generate plasma, however, Ar, oxygen and nitrogen at different gas compositions were compared in the pinhole plasma jet system. The Taguchi design model was used to study the effects of gas compositions. Results revealed that the pinhole plasma jet system was able to degrade over 50% of the diuron in 60 minutes. The optimal plasma generation condition for the highest degradation of diuron used pure Ar gas. The highest degradation percentage of herbicide in PAS corresponded to the lowest hydrogen peroxide (H₂O₂) content, nitrite concentration and electrical conductivity (EC) of the PAS. The diuron degradation products were identified as 3,4-dichloro-benzenamine, 1-chloro-3-isocyanato-benzene and 1-chloro-4-isocyanato-benzene via gas chromatography-mass spectrometry (GC-MS). The GA plasma system was not adequate for the degradation of herbicide in PAS.

Analytical assessment of modulated electric flux triggered degradation of chlorfenapyr and deltamethrin pesticides in guava fruits

The purpose of this study was to explore the new effective method and investigate the dissipation of chlorfenapyr and deltamethrin (DM) pesticides used in the treatment of guava fruit from tropical and sub-tropical areas of Pakistan. Five different solutions of varying concentrations of pesticides were prepared. This study involved the in-vitro and in-vivo analysis of modulated electric flux-triggered degradation as an efficient method for the safer degradation of selected pesticides. The Taser gun was used as a tool for providing different numbers of electrical shocks of million voltages to the pesticides present in guava fruit at different temperatures. The degraded pesticides were extracted and analyzed by High-performance liquid chromatography (HPLC). The HPLC chromatograms verified that significant dissipation of pesticides took place when these were exposed to 9 shocks at 37 °C, which proved the efficiency of this degradation method. More than 50% of the total spray of both pesticides was dissipated. Thus, modulated electrical flux-triggered degradation is one of the effective methods for pesticide degradation.

Photolysis of the novel meta-diamide insecticide broflanilide in solutions: Kinetics, degradation pathway, DFT calculation and ecotoxicity assessment

Broflanilide, as a novel meta-diamide insecticide, presents high bioactivity against agricultural pests. However, there was limited report regarding the photolysis fate of broflanilide. In this study, the photodegradation kinetics and influence factors of broflanilide, including different solvents, pH, iron, S₂O₈^2- and SO₃^2- were investigated under UV condition, and the reaction mechanism and transformation pathway were explored. The reaction rates (k) showed solvent-specificity in ultrapure water (0.015 min^-1), ethyl acetate (0.051 min^-1), methanol (0.084 min^-1) and acetonitrile (0.193 min^-1), correspondingly. The photolysis of broflanilide was slowest in the acid condition (pH = 4.0) compared with that in the neutral (pH = 7.0) and alkaline (pH = 9.0) conditions. The iron (Fe²⁺ and Fe³⁺) presented significant inhibition on the photodegradation due to the light shielding effect. Additionally, the UV/peroxydisulfate (S₂O₈^2-) and UV/sulfite (SO₃^2-) technologies could effectively accelerate the photodegradation of broflanilide, which has the potential for rapid treatment of pesticides in the aqueous environment. Six transformation products (TPs) were detected in water, peroxydisulfate and sulfite solutions, and the possible transformation pathways, including dehalogenation, cyclization, N-dealkylation, oxidation, reduction and hydrolysis, were proposed. Importantly, the reaction mechanism was explained through the analysis of molecular electrostatic potential and molecular orbitals. The predicted toxicity of the TPs indicated that several highly toxic TPs need to pay more attention in future risk assessments. This study provides a new perspective for evaluating the ecological fate and risks of pesticides.

Drug Delivery Strategies for Avobenzone: A Case Study of Photostabilization

Several developments and research methods are ongoing in drug technology and chemistry research to elicit effectiveness regarding the therapeutic activity of drugs along with photoprotection for their molecular integrity. The detrimental effect of UV light induces damaged cells and DNA, which leads to skin cancer and other phototoxic effects. The application of sunscreen shields to the skin is important, along with recommended UV filters. Avobenzone is widely used as a UVA filter for skin photoprotection in sunscreen formulations. However, keto-enol tautomerism propagates photodegradation into it, which further channelizes the phototoxic and photoirradiation effects, further limiting its use. Several approaches have been used to counter these issues, including encapsulation, antioxidants, photostabilizers, and quenchers. To seek the gold standard approach for photoprotection in photosensitive drugs, combinations of strategies have been implemented to identify effective and safe sunscreen agents. The stringent regulatory guidelines for sunscreen formulations, along with the availability of limited FDA-approved UV filters, have led many researchers to develop perfect photostabilization strategies for available photostable UV filters, such as avobenzone. From this perspective, the objective of the current review is to summarize the recent literature on drug delivery strategies implemented for the photostabilization of avobenzone that could be useful to frame industrially oriented potential strategies on a large scale to circumvent all possible photounstable issues of avobenzone.

Photodegradation of the Novel Herbicide Pyraquinate in Aqueous Solution: Kinetics, Photoproducts, Mechanisms, and Toxicity Assessment

Pyraquinate, a newly developed 4-hydroxyphenylpyruvate dioxygenase class herbicide, has shown excellent control of resistant weeds in paddy fields. However, its environmental degradation products and corresponding ecotoxicological risks after field application remain ambiguous. In this study, we systematically investigate the photolytic behaviors of pyraquinate in aqueous solutions and in response to xenon lamp irradiation. The degradation follows first-order kinetics, and its rate depends on pH and the amount of organic matter. No vulnerability to light radiation is indicated. Ultrahigh-performance liquid chromatography with quadrupole-time-of-flight mass spectrometry and UNIFI software analysis reveals six photoproducts generated by methyl oxidation, demethylation, oxidative dechlorination, and ester hydrolysis. Gaussian calculation suggests that activities due to hydroxyl radicals or aquatic oxygen atoms caused these reactions on the premise of obeying thermodynamic criteria. Practical toxicity test results show that the toxicity of pyraquinate to zebrafish embryos is low but increases when the compound is combined with its photoproducts.

Degradation strategies of pesticide residue: From chemicals to synthetic biology

The past 50 years have witnessed a massive expansion in the demand and application of pesticides. However, pesticides are difficult to be completely degraded without intervention hence the pesticide residue could pose a persistent threat to non-target organisms in many aspects. To aim at the problem of the abuse of pesticide products and excessive pesticide residues in the environment, chemical and biological degradation methods are widely developed but are scaled and insufficient to solve such a pollution. In recent years, bio-degradative tools instructed by synthetic biological principles have been further studied and have paved a way for pesticide degradation. Combining the customized design strategy and standardized assembly mode, the engineering bacteria for multi-dimensional degradation has become an effective tool for pesticide residue degradation. This review introduces the mechanisms and hazards of different pesticides, summarizes the methods applied in the degradation of pesticide residues, and discusses the advantages, applications, and prospects of synthetic biology in degrading pesticide residues.

Green photocatalytic remediation of Fenthion using composites with natural red clay and non-toxic metal oxides with visible light irradiation

In the present work, composites with non-toxic metal oxides, such as TiO₂ and ZnO, and a natural red clay (taua) reach in hematite were used in the photocatalytic degradation of Fenthion. The composite TiO₂/Taua (0.5:1 wt. ratio) and pure TiO₂ were prepared by sol-gel method while ZnO/Taua (0.5:1 wt. ratio) and pure ZnO were prepared by Pechini method. The materials were characterized by XRD, SEM, EDX, and DRS. The anatase phase was formed in both pure TiO₂ and TiO₂/Taua, while the hexagonal phase was formed in pure ZnO and ZnO/Taua. The bandgap energies for the two composites were narrowed compared to the respective pure oxides as consequence of the hematite (α-Fe₂O₃, E_g = 2.1 eV) in the red clay, reaching 2.1 eV for TiO₂/Taua and 2.0 eV for ZnO/Taua, while the bandgap energies for pure TiO₂ and ZnO were 3.2 and 3.0 eV, respectively. Fenthion was not degraded in the dark, but the concentration droped 20% after 180 min under visible light irradiation without photocatalyst and 60% after 210 min in the presence of the pure red clay. Both TiO₂/Taua and ZnO/Taua composites were also photocatalytic active to degrade Fenthion (λ > 420 nm), with degradation of 78% (in 180 min) and 85% (in 210 min) respectively. In the optimized conditions (pH 2, 100 mg L^-1 of H₂O₂ and 30 mg L^-1 of Fenthion), the ZnO/Taua composite was the most efficient, reaching 89% degradation in up to 30 min, with Fenthion sulfoxide as the degradation product.

Harmful health effects of pesticides used on museum textile artifacts - overview

The paper discusses the types of fibers contained in the museum textile artifacts and the types of pests and pesticides. Also, the main health problems associated with pesticide exposure are presented. Textile fibers represent an excellent source of food for microbes and insects. The key to the long-term preservation of textiles is by implementing an integrated management program for pest and environmental conditions control. The main types of pesticides are insecticides, herbicides, fungicides, rodenticides, acaricides, and fumigants and a way for classification can be made according to the LD50 (lethal dose) value which evaluates the toxicity of a pesticide. Depending on the LD50 values, pesticides can be very toxic, moderately toxic, slightly toxic, and relatively non-toxic. Exposure to pesticides can occur through 4 four routes: oral, dermal, respiratory, and eye exposure. The main diseases that can be associated with exposure to pesticides are discussed in the paper. In the end, a basic set of precautionary recommendations when handling museum objects that may contain hazardous materials was presented.

Chemical Control of Mosquitoes and the Pesticide Treadmill: A Case for Photosensitive Insecticides as Larvicides

Insecticides reduce the spread of mosquito-borne disease. Over the past century, mosquito control has mostly relied on neurotoxic chemicals-such as pyrethroids, neonicotinoids, chlorinated hydrocarbons, carbamates and organophosphates-that target adults. However, their persistent use has selected for insecticide resistance. This has led to the application of progressively higher amounts of insecticides-known as the pesticide treadmill-and negative consequences for ecosystems. Comparatively less attention has been paid to larvae, even though larval death eliminates a mosquito's potential to transmit disease and reproduce. Larvae have been targeted by source reduction, biological control, growth regulators and neurotoxins, but hurdles remain. Here, we review methods of mosquito control and argue that photoactive molecules that target larvae-called photosensitive insecticides or PSIs-are an environmentally friendly addition to our mosquitocidal arsenal. PSIs are ingested by larvae and produce reactive oxygen species (ROS) when activated by light. ROS then damage macromolecules resulting in larval death. PSIs are degraded by light, eliminating environmental accumulation. Moreover, PSIs only harm small translucent organisms, and their broad mechanism of action that relies on oxidative damage means that resistance is less likely to evolve. Therefore, PSIs are a promising alternative for controlling mosquitoes in an environmentally sustainable manner.

Impact of water matrices on oxidation effects and mechanisms of pharmaceuticals by ultraviolet-based advanced oxidation technologies: A review

The binding between water components (dissolved organic matters, anions and cations) and pharmaceuticals influences the migration and transformation of pollutants. Herein, the impact of water matrices on drug degradation, as well as the electrical energy demands during UV, UV/catalysts, UV/O₃, UV/H₂O₂-based, UV/persulfate and UV/chlorine processes were systemically evaluated. The enhancement effects of water constituents are due to the powerful reactive species formation, the recombination reduction of electrons and holes of catalyst and the catalyst regeneration; the inhibition results from the light attenuation, quenching effects of the excited states of target pollutants and reactive species, the stable complexations generation and the catalyst deactivation. The transformation pathways of the same pollutant in various AOPs have high similarities. At the same time, each oxidant also can act as a special nucleophile or electrophile, depending on the functional groups of the target compound. The electrical energy per order (EEO) of drugs degradation may follow the order of EEO_UV > EEO_UV/catalyst > EEO_UV/H2O2 > EEO_UV/PS > EEO_UV/chlorine or EEO_UV/O3. Meanwhile, it is crucial to balance the cost-benefit assessment and toxic by-products formation, and the comparison of the contaminant degradation pathways and productions in the presence of different water matrices is still lacking.

Removal of emerging pollutants by a 3-step system: Hybrid digester, vertical flow constructed wetland and photodegradation post-treatments

The removal of emerging pollutants from municipal wastewater was studied for the first time using a three-step pilot-scale system: 1) hybrid digester (HD) as first step, 2) subsurface vertical flow constructed wetland (VF) as second step, and 3) photodegradation (PD) unit as third step or post-treatment. The HD and VF units were built and operated in series with effluent recirculation at pilot scale. For the PD post-treatment, three alternatives were studied at lab-scale, i) UVC irradiation at 254 nm (0.5 h exposure time), ii) UVA irradiation at 365 nm using a TiO₂-based photocatalyst and iii) sunlight irradiation using a TiO₂-based photocatalyst, the last two for 1 and 2 h. Alternative iii) was also tested at pilot-scale. Degradation of nine compounds was evaluated: acetaminophen (ACE), caffeine (CAF), carbamazepine (CBZ), ketoprofen (KET), ibuprofen (IBU), diclofenac (DCL), clofibric acid (ACB), bisphenol A (BPA), and sotalol (SOT). Overall, the HD-VF-UVC system completely removed (>99.5 %) ACE, CAF, KET, IBU, DCL and ACB, and to a lesser extent SOT (98 %), BPA (83 %) and CBZ (51 %). On the other hand, the HD-VF-UVA/TiO₂ system (at 2 h) achieved >99.5 % removal of ACE, CAF, KET, IBU and DCL while ACB, BPA, CBZ and SOT were degraded by 83 %, 81 %, 78 % and 68 %, respectively. Working also at 2 h of exposure time, in summer conditions, the HD-VF-Sol/TiO₂ system achieved >99.5 % removal of ACE, CAF, KET, IBU, DCL and ACB, and to a minor extent BPA (80 %), SOT (74 %) and CBZ (69 %). Similar results, although slightly lower for SOT (60 %) and CBZ (59 %), were obtained in the pilot sunlight plus TiO₂ catalyst unit. However, the use of sunlight irradiation with a TiO₂-based photocatalyst clearly showed lower removal efficiency in autumn conditions (i.e., 47 % SOT, 31 % CBZ).

Transformation and stable isotope fractionation of the urban biocide terbutryn during biodegradation, photodegradation and abiotic hydrolysis

Terbutryn is a widely used biocide in construction materials like paint and render to prevent the growth of microorganisms, algae and fungi. Terbutryn is released from the facades into the environment during rainfall, contaminating surface waters, soil and groundwater. Knowledge of terbutryn dissipation from the facades to aquatic ecosystems is scarce. Here, we examined in laboratory microcosms degradation half-lives, formation of transformation products and carbon and nitrogen isotope fractionation during terbutryn direct (UV light with λ = 254 nm and simulated sunlight) and indirect (simulated sunlight with nitrate) photodegradation, abiotic hydrolysis (pH = 1, 7 and 13), and aerobic biodegradation (stormwater pond sediment, soil and activated sludge). Biodegradation half-lives of terbutryn were high (>80 d). Photodegradation under simulated sunlight and hydrolysis at extreme pH values indicated slow degradability and accumulation in the environment. Photodegradation resulted in a variety of transformation products, whereas abiotic hydrolysis lead solely to terbutryn-2-hydroxy in acidic and basic conditions. Biodegradation indicates degradation to terbutryn-2-hydroxy through terbutryn-sulfoxide. Compound-specific isotope analysis (CSIA) of terbutryn holds potential to differentiate degradation pathways. Carbon isotope fractionation values (ε_C) ranged from -3.4 ± 0.3‰ (hydrolysis pH 1) to +0.8 ± 0.1‰ (photodegradation under UV light), while nitrogen isotope fractionation values ranged from -1.0 ± 0.4‰ (simulated sunlight photodegradation with nitrate) to +3.4 ± 0.2‰ (hydrolysis at pH 1). In contrast, isotope fractionation during biodegradation was insignificant. Λ^N/C values ranged from -1.0 ± 0.1 (hydrolysis at pH 1) to 2.8 ± 0.3 (photodegradation under UV light), allowing to differentiate degradation pathways. Combining the formation of transformation products and stable isotope fractionation enabled identifying distinct degradation pathways. Altogether, this study highlights the potential of CSIA to follow terbutryn degradation in situ and differentiate prevailing degradation pathways, which may help to monitor urban biocide remediation and mitigation strategies.

Finding Fluorine: Photoproduct Formation during the Photolysis of Fluorinated Pesticides

The photolysis of pesticides with different fluorine motifs was evaluated to quantify the formation of fluorinated products in buffered aqueous systems, advanced oxidation (AOP) and reduction processes (ARP), and river water. Simulated sunlight quantum yields at pH 7 were 0.0033, 0.0025, 0.0015, and 0.00012 for penoxsulam, florasulam, sulfoxaflor, and fluroxypyr, respectively. The bimolecular rate constants with hydroxyl radicals were 2 to 5.7 × 1010 M-1 s-1 and, with sulfate radicals, 1.6 to 2.6 × 108 M-1 s-1 for penoxsulam, florasulam, and fluroxypyr, respectively. The rate constants of sulfoxaflor were 100-fold lower. Using quantitative 19F-NMR, complete fluorine mass balances were obtained. The maximum fluoride formation was 53.4 and 87.4% for penoxsulam and florasulam under ARP conditions, and 6.1 and 100% for sulfoxaflor and fluroxypyr under AOP conditions. Heteroaromatic CF3 and aliphatic CF2 groups were retained in multiple fluorinated photoproducts. Aryl F and heteroaromatic F groups were readily defluorinated to fluoride. CF3 and CF2 groups formed trifluoroacetate and difluoroacetate, and yields increased under oxidizing conditions. 19F-NMR chemical shifts and coupling analysis provided information on hydrogen loss on adjacent bonds or changes in chirality. Mass spectrometry results were consistent with the observed 19F-NMR products. These results will assist in selecting treatment processes for specific fluorine motifs and in the design of agrochemicals to reduce byproduct formation.

Photolysis for the Removal and Transformation of Pesticide Residues During Food Processing: A State-of-the-Art Minireview

Pesticide residues are of great significant issue that exerted adverse effects on humans. There is a need for effective and non-toxic decontamination of pesticide residues during food processing. In this minireview, the recent advances in the degradation of pesticide residues by photolysis have been firstly described during food processing. The mechanisms of pesticide residues destruction by photolysis were discussed accordingly. Finally, applications of photolysis in the degradation of pesticide residues from beverages, fresh produce, and food rinse waste were also summarized.

Advances on removal of organophosphorus pesticides with electrochemical technology

Widespread use of organophosphorus pesticides (OPs), especially superfluous and unreasonable use, had brought huge harm to the environment and food chain. It is because only a small part of the pesticides sprayed reached the target, and the rest slid across the soil, causing pollution of groundwater and surface water resources. These pesticides accumulate in the environment, causing environmental pollution. Therefore, in recent years, the control and degradation of OPs have become a public spotlight and research hotspot. Due to its unique advantages such as versatility, environmental compatibility, controllability, and cost-effectiveness compatibility, electrochemical technology has become one of the most promising methods for degradation of OPs. The fundamental knowledge about electrochemical degradation on OPs was introduced in this review. Then, a comprehensive overview of four main types of practical electrochemical technologies to degrade pesticides were presented and evaluated. The knowledge contained herein should conduce to better understand the degradation of pesticides by electrochemical technology, and better exploit the degradation of pesticides in the environment and food. Overall, the objective of this review is to provide comprehensive guidance for rational design and application of electrochemical technology in the degradation of OPs for the safety of the environment and food chain in the future.

Photochemical interactions between pesticides and plant volatiles

Among the numerous studies devoted to the photodegradation of pesticides, very scarce are those investigating the effect of plant volatiles. Yet, pesticides can be in contact with plant volatiles after having been spread on crops or when they are transported in surface water, making interactions between the two kinds of chemicals possible. The objectives of the present study were to investigate the reactions occurring on plants. We selected thyme as a plant because it is used in green roofs and two pesticides: the fungicide chlorothalonil for its very oxidant excited state and the insecticide imidacloprid for its ability to release the radical NO₂ under irradiation. Pesticides were irradiated with simulated solar light first in a solvent ensuring a high solubility of pesticides and plant volatiles, and then directly on thyme's leaves. Analyses were conducted by headspace gas chromatography-mass spectrometry (HS-GC-MS), GC-MS and liquid chromatography-high resolution mass spectrometry (LC-HRMS). In acetonitrile, chlorothalonil photosensitized the degradation of thymol, α-pinene, 3-carene and linalool with high quantum yields ranging from 0.35 to 0.04, and was photoreduced, while thymol underwent oxidation, chlorination and dimerization. On thyme's leave, chlorothalonil was photoreduced again and products arising from oxidation and dimerization of thymol were detected. Imidacloprid photooxidized and photonitrated thymol in acetonitrile, converting it into chemicals of particular concern. Some of these chemicals were also found when imidacloprid was irradiated dispersed on thyme's leaves. These results show that photochemical reactions between pesticides and the plants secondary metabolites can take place in solution as on plants. These findings demonstrate the importance to increase our knowledge on these complex scenarios that concern all the environmental compartments.

Recent Progress and Prospects in Catalytic Water Treatment

Presently, conventional technologies in water treatment are not efficient enough to completely mineralize refractory water contaminants. In this context, the implementation of catalytic processes could be an alternative. Despite the advantages provided in terms of kinetics of transformation, selectivity, and energy saving, numerous attempts have not yet led to implementation at an industrial scale. This review examines investigations at different scales for which controversies and limitations must be solved to bridge the gap between fundamentals and practical developments. Particular attention has been paid to the development of solar-driven catalytic technologies and some other emerging processes, such as microwave assisted catalysis, plasma-catalytic processes, or biocatalytic remediation, taking into account their specific advantages and the drawbacks. Challenges for which a better understanding related to the complexity of the systems and the coexistence of various solid-liquid-gas interfaces have been identified.

Effect of Solution pH on the Dual Role of Dissolved Organic Matter in Sensitized Pollutant Photooxidation

Dissolved organic matter (DOM) has a dual role in indirect phototransformations of aquatic contaminants by acting both as a photosensitizer and an inhibitor. Herein, the pH dependence of the inhibitory effect of DOM and the underlying mechanisms were studied in more than 400 kinetic irradiation experiments over the pH range of 6-11. Experiments employed various combinations of one of three DOM isolates, one of two model photosensitizers, the model antioxidant phenol, and one of nine target compounds (TCs), comprising several aromatic amines, in particular anilines and sulfonamides, and 4-cyanophenol. Using model photosensitizers without antioxidants, the phototransformation of most TCs increased with increasing pH, even for TCs for which pH did not affect speciation. This trend was attributed to pH-dependent formation yields of TC-derived radicals and their re-formation to the parent TC. Analogous trends were observed with DOM as a photosensitizer. Comparison of model and DOM photosensitizer data sets showed increasing inhibitory effects of DOM on TC phototransformation kinetics with increasing pH. In systems with anilines as a TC and phenol as a model antioxidant, pH trends of the inhibitory effect could be rationalized based on the reduction potential difference (ΔE_red) of phenoxyl/phenol and anilinyl/aniline couples. Our results indicate that the light-induced transformation of aromatic amines in the aquatic environment is governed by the pH-dependent inhibitory effects of antioxidant phenolic moieties of DOM and pH-dependent processes related to the formation of amine oxidation intermediates.

Identification of photodegradation product of organophosphorus pesticides and elucidation of transformation mechanism under simulated sunlight irradiation

Organophosphorus pesticides (OPs) are posing great threat to the environment and human health, due to their overuse and persistence in the environment. Photolysis has been established as an effective method to degrade OPs. The influence of pH value, the initial concentration of pesticides and the light source on the photolysis of two OPs, including chlorpyrifos and dimethoate, was investigated. The optimal reaction condition for OPs degradation was under pH 9, with xenon lamp as the light source, in which the photodegradation efficiencies of chlorpyrifos and dimethoate (500 mg/L) were 75.12% and 94.31%, respectively. The photodegradation products of chlorpyrifos and dimethoate were identified by GC-MS. Also, density functional theory (DFT) calculations were used to characterize the molecular properties of chlorpyrifos and dimethoate, as well as predicting potential photolysis reactions. Photodegradation mechanisms of chlorpyrifos and dimethoate were proposed, in which 3,5,6-trichloropyridinol (TCP), O,O-diethyl thiophosphate (DETP), 2,3,5-Trichloro-6-methoxypyridine (TMP) and O,O,S-trimethyl phosphorothioate were identified as the main products of chlorpyrifos degradation. Omethoate, O,O,S-trimethyl thiophosphorothioate, N-methyl-2-sulfanylacetamide, O,O,O-trimethyl thiophosphate, O,O,S-trimethylphosphorothiate, and O,O,O-trimethyl phosphoric ester as the main photodegradation products for dimethoate. The main degradation mechanisms included ring opening, cleavage, oxidation and demethylation. This work demonstrated the feasibility of combining chemical analysis with quantum chemical calculation in unraveling degradation mechanisms of OPs. Also, it is of great significance for evaluating the environmental fate of OPs in aquatic system and further environmental risk assessment.

Application of Compound-Specific Isotope Analysis in Environmental Forensic and Strategic Management Avenue for Pesticide Residues

Unintended pesticide pollution in soil, crops, and adjacent environments has caused several issues for both pesticide users and consumers. For users, pesticides utilized should provide higher yield and lower persistence while considering both the environment and agricultural products. Most people are concerned that agricultural products expose humans to pesticides accumulating in vegetation. Thus, many countries have guidelines for assessing and managing pesticide pollution, for farming in diverse environments, as all life forms in soil are untargeted to these pesticides. The stable isotope approach has been a useful technique to find the source of organic matter in studies relating to aquatic ecology and environmental sciences since the 1980s. In this study, we discuss commonly used analytical methods using liquid and gas chromatography coupled with isotopic ratio mass spectrometry, as well as the advanced compound-specific isotope analysis (CSIA). CSIA applications are discussed for tracing organic pollutants and understanding chemical reactions (mechanisms) in natural environments. It shows great applicability for the issues on unintended pesticide pollution in several environments with the progress history of isotope application in agricultural and environmental studies. We also suggest future study directions based on the forensic applications of stable isotope analysis to trace pesticides in the environment and crops.

Photodegradation of pesticides using compound-specific isotope analysis (CSIA): a review

Pesticides are commonly applied in agriculture to protect crops from pests, weeds, and harmful pathogens. However, chronic, low-level exposure to pesticides can be toxic to humans. Photochemical degradation of pesticides in water, soil, and other environmental media can alter their environmental fate and toxicity. Compound-specific isotope analysis (CSIA) is an advanced diagnostic tool to quantify the degradation of organic pollutants and provide insight into reaction mechanisms without the need to identify transformation products. CSIA allows for the direct quantification of organic degradation, including pesticides. This review summarizes the recent developments observed in photodegradation studies on different categories of pesticides using CSIA technology. Only seven pesticides have been studied using photodegradation, and these studies have mostly occurred in the last five years. Knowledge gaps in the current literature, as well as potential approaches for CSIA technology for pesticide monitoring, are discussed in this review. Furthermore, the CSIA analytical method is challenged by chemical element types, the accuracy of instrument analysis, reaction conditions, and the stability of degradation products. Finally, future research applications and the operability of this method are also discussed.

Transformation of fluopyram during enzymatic hydrolysis of apple and its effect on polygalacturonase and apple juice yield

China is one of the largest apple-growing areas in the world. Fluopyram (FLP) is a novel pesticide that has been widely used in agriculture. This work investigated the behavior of pesticides during enzymatic hydrolysis of apple juice and its effect on polygalacturonase (PG), apple juice yield, and flavor. The study findings revealed that 27.5% to 34.2% FLP was degraded during the enzymatic hydrolysis of apple. The three degradation products (P1, P2, and P3) were identified by a hybrid ion trap-orbitrap mass spectrometer. Based on toxicity assessment, it was found that carcinogenicity was higher for P2 and P3 than for FLP. Furthermore, FLP affected the yield and flavor of apple juice. FLP reduced yield by 4.8%, because FLP inhibited the activity of PG. Through molecular docking, it was found that there was an interaction between the active center of PG and FLP, resulting in a reduction in catalytic ability.

Direct photodegradation of 36 organic micropollutants under simulated solar radiation: Comparison with free-water surface constructed wetland and influence of chemical structure

Micropollutants such as pharmaceuticals and pesticides are still found in treated municipal effluent and are discharged into the natural environment. Natural direct photodegradation may be one pathway for removing these micropollutants in treatment processes such as free-water surface constructed wetlands (CW). This work was set out to evaluate the half-life (t_1/2) of direct photodegradation of 36 micropollutants under controlled conditions of light exposure close to solar radiation. The results allowed to classify the micropollutants into three groups (fast, medium and slow). Seven micropollutants were classified in the fast group with t_1/2 between 0.05 h and 0.79 h, 24 in the medium group with t_1/2 between 5.3 h and 49.7 h, and five in the slow group with t_1/2 between 56 h and 118 h. The t_1/2 values obtained in laboratory were compared with those from a CW receiving treated wastewater. Correction factors were calculated to adjust the in situ data for the light intensity in laboratory and improved the correspondence especially for the micropollutants of the fast and medium groups. Finally, an innovative method based on statistical tests highlighted the chemical functions characteristic of micropollutants sensitive to photodegradation (OH-C˭O, C˭N-O-, =N-OH, -CH=N, -O-P˭O, -C˭C-) and with low sensitivity (-O-R, -Cl).

The effect of the pesticide delivery method on the microbial community of field soil

The study deals with the effects of herbicides (metribuzin, tribenuron-methyl, fenoxaprop-P-ethyl) and fungicides (tebuconazole, epoxiconazole, azoxystrobin) applied to soil as free pesticides or as slow release formulations embedded in a biodegradable composite matrix on the structure of the soil microbial community. The matrix consisted of a natural biopolymer poly-3-hydroxybutyrate [P(3HB)] and a filler-one of the natural materials (peat, clay, and wood flour). The soil microbial community was characterized, including the major eco-trophic groups of bacteria, dominant taxa of bacteria and fungi, and primary P(3HB)-degrading microorganisms, such as Pseudomonas, Bacillus, Pseudarthrobacter, Streptomyces, Penicillium, and Talaromyces. The addition of free pesticides adversely affected the abundance of soil microorganisms; the decrease varied from 1.4 to 56.0 times for different types of pesticides. The slow release pesticide formulations, in contrast to the free pesticides, exerted a much weaker effect on soil microorganisms, no significant inhibition in the abundance of saprotrophic bacteria was observed, partly due to the positive effects of the composite matrix (polymer/natural material), which was a supplementary substrate for microorganisms. The slow release fungicide formulations, like the free fungicides, reduced the total abundance of fungi and inhibited the development of the phytopathogens Fusarium and Alternaria. Thus, slow release formulations of pesticides preserve the bioremediation potential of soil microorganisms, which are the main factor of removing xenobiotics from the biosphere.

UV treatment for degradation of chemical contaminants in food: A review

Application of ultraviolet (UV) irradiation for the degradation of chemical contaminants in food products has gained more and more interest in the past two decades. The majority of the research in this field was on mycotoxins, especially aflatoxins and patulin, with limited studies on pesticide residues and other chemical contaminants in food. These studies have been focused on identifying the structure and toxicity of degradation products, investigating the influence of UV treatment factors on the degradation efficiency, determining the impact of UV treatment on the quality of food products, and developing updated UV treatment methods such as TiO₂ induced photocatalytic degradation. The summary of published literatures provided insights into future research opportunities in this area, which include determining a standard for the UV treatment description, working with naturally contaminated samples rather than artificially spiked samples, conducting pilot plant or industrial scale studies, examining more targets and conducting multi-targets studies, and developing more innovative methods for UV treatment.

Degradation of highly chlorinated pesticide, lindane, in water using UV/persulfate: kinetics and mechanism, toxicity evaluation, and synergism by H2O2

Sulfate radical-advanced oxidation processes (SR-AOPs) are emerging technologies for decomposing organic pollutants in water. This study investigated the efficiency of UV/persulfate (UV/S₂O₈^2-) process to degrade lindane in water, showing 93.2% lindane removal ([lindane]₀ = 3.43 μM, [S₂O₈^2-]₀ = 100 μM) at a UV fluence of 720 mJ/cm². The lindane degradation followed first order kinetics and mechanistic studies suggested H-abstraction by SO₄^•- and Cl removal via C-Cl bond cleavage by UV-C light. Toxicity assessment using ECOSAR program showed toxicity gradually decreased and eventually no significant toxicity remained when all by-products vanished at high UV dose. Removal efficiency of lindane decreased from 93.2% to 38.4, 45.5, 56.0, 84.3 and 88.6%, by adding 1.0 mg/L humic acid or 1.0 mM CO₃^2-, HCO₃^-, Cl^- or SO₄^2-, respectively. Coupling of H₂O₂ with UV/S₂O₈^2- showed a significant synergistic effect with 99.0% lindane removal at a UV fluence of 600 mJ/cm², using [S₂O₈^2-]₀ = [H₂O₂]₀ = 50 μM while UV/H₂O₂ resulted in only 36.6% lindane removal ([lindane]₀ = 3.43 μM, [H₂O₂]₀ = 100 μM) at a UV fluence of 720 mJ/cm². The results indicate that SR-AOP has potential for consideration as a remedial technology to treat persistent chlorinated pesticides such as lindane in contaminated water.

Preparative isolation of the major metabolite NK-1375 of diamide insecticide cyclaniliprole and its application to pertinent residue analysis in plant-origin foods using UHPLC-MS/MS

NK-1375 is a major metabolite of the diamide insecticide cyclaniliprole (CYCP) with toxicological significance. It is formed in various transformation pathways of CYCP, including photolysis and plant metabolism. In the present study, NK-1375 was produced employing the liquid-phase photolysis of CYCP followed by isolation using preparative liquid chromatography. The structure of the isolated substance was confirmed using MS and ¹ H NMR spectroscopy, and its purity was measured to be 95.9% using HPLC. As its application, a residue analysis method was first developed for the simultaneous determination of CYCP and NK-1375 in six representative plant-origin foods using fast multi-plug filtration cleanup and UHPLC-MS/MS. Excellent linearity (r > 0.999) was obtained over the calibration range from 0.001 to 0.1 μg mL^-1 . The recoveries (intra-day and inter-day) of CYCP and NK-1375 from different matrices ranged from 74 to 112%, with corresponding relative standard deviations less than 13%. The limits of quantitation of these two compounds were defined at 0.01 mg kg^-1 . This study can be useful for the subsequent analytical or toxicological research on this important pesticide metabolite.

Photodegradation kinetics, mechanism and aquatic toxicity of deltamethrin, permethrin and dihaloacetylated heterocyclic pyrethroids

Photochemical methods attracted much research interests for their high-efficiency and low secondary pollution. Decomposition of synthetic pyrethroids, the fourth major group of insecticides in use worldwide, was also of great significance due to their possible environmental risks. The photodegradation of deltamethrin, permethrin and dihaloacetylated heterocyclic pyrethroids in methanol/acetone = 9/1 (by volume) by a 400 W mercury lamp was examined. The t_1/2 of tested pyrethroids was less than 25 min, except for cis-permethrin with a t_1/2 of up to 50 min. The trans-isomer of permethrin and compound DCA-01 with a smaller t_1/2 might be more susceptible to degradation than their cis-isomer. Besides, the photodegradation of pyrethroids was divided into twelve pathways including isomerization, ester hydrolysis, ester bond cleavage, CO bond cleavage, 3,3-dimethylacrylate formation, double bond break, C1-C3 bond cleavage in cyclopropyl, reductive dehalogenation, decarboxylation, nucleophilic reagents attack on lone pair electrons on oxygen atoms in the phenyl ether, cyano hydrolysis, and halogenated hydrocarbon hydrolysis. The ECOSAR program displayed that pyrethroids and most of their photodegradation products were toxic to fish, daphnid, green algae. Particularly, some photodegradation products were more harmful to aquatic organisms than their parents.