Enhancement of the Nanofibrillation of Wood Cellulose through Sequential Periodate–Chlorite Oxidation

Sustainable preparation of cellulose nanofibrils via choline chloride-citric acid deep eutectic solvent pretreatment combined with high-pressure homogenization

Developing green and simple methods for the preparation of cellulose nanofibrils (CNFs) is of great significance. Herein, a green deep eutectic solvent (DES) system based on choline chloride (ChCl) and citric acid (CA) is employed to pretreat cellulose fibers for the preparation of CNFs. The effect of the pretreatment temperature on the chemo-physical properties of the CNFs is comprehensively investigated. A high CNFs yield of up to 84.19% can be achieved under optimized conditions. The optimal CNFs show a narrow diameter distribution and length up to several microns, high crystallinity and thermal stability, as well as excellent dispersibility in water. Furthermore, semi-transparent and flexible cellulose nanopaper (CNP) was fabricated through a facile vacuum filtration process. The optimal CNP shows high tensile strength (175.15 MPa) and toughness (7.51 MJ/m³). Therefore, this work provides a sustainable and facile approach to fabricate CNFs and CNP, which can be potentially used for various high-tech applications.

Sustainable isolation of nanocellulose from cellulose and lignocellulosic feedstocks: Recent progress and perspectives

As a type of sustainable nanomaterials, nanocellulose has drawn increasing attention over the last two decades due to its great potential in diverse value-added applications such as electronics, sensors, energy storage, packaging, pharmaceuticals, biomedicine, and functional food. Sourcing nanocellulose from lignocellulose is commonly accomplished via the use of mineral acids, oxidizers, enzymes, and/or intensive mechanical energy. Yet, the economic and environmental concerns associated with these conventional isolation techniques pose major obstacles for commercialization. Considerable progress has been achieved in the last few years in developing sustainable nanocellulose isolation technologies involving organic acid/anhydride, Lewis acid, solid acid, ionic liquid, and deep eutectic solvent. This paper provides a comprehensive review of these alternatives with regard to general procedures and key advantages. Important knowledge gaps, including total biomass utilization, complete life cycle analysis, and health/safety, require urgently bridging in order to develop economically competitive and operationally feasible nanocellulose isolation technology for commercialization.

Towards sustainable production and utilization of plant-biomass-based nanomaterials: a review and analysis of recent developments

Plant-biomass-based nanomaterials have attracted great interest recently for their potential to replace petroleum-sourced polymeric materials for sustained economic development. However, challenges associated with sustainable production of lignocellulosic nanoscale polymeric materials (NPMs) need to be addressed. Producing materials from lignocellulosic biomass is a value-added proposition compared with fuel-centric approach. This report focuses on recent progress made in understanding NPMs-specifically lignin nanoparticles (LNPs) and cellulosic nanomaterials (CNMs)-and their sustainable production. Special attention is focused on understanding key issues in nano-level deconstruction of cell walls and utilization of key properties of the resultant NPMs to allow flexibility in production to promote sustainability. Specifically, suitable processes for producing LNPs and their potential for scaled-up production, along with the resultant LNP properties and prospective applications, are discussed. In the case of CNMs, terminologies such as cellulose nanocrystals (CNCs) and cellulose nanofibrils (CNFs) used in the literature are examined. The term cellulose nano-whiskers (CNWs) is used here to describe a class of CNMs that has a morphology similar to CNCs but without specifying its crystallinity, because most applications of CNCs do not need its crystalline characteristic. Additionally, progress in enzymatic processing and drying of NPMs is also summarized. Finally, the report provides some perspective of future research that is likely to result in commercialization of plant-based NPMs.

Rheological Aspects of Cellulose Nanomaterials: Governing Factors and Emerging Applications

Cellulose nanomaterials (CNMs), mainly including nanofibrillated cellulose (NFC) and cellulose nanocrystals (CNCs), have attained enormous interest due to their sustainability, biodegradability, biocompatibility, nanoscale dimensions, large surface area, facile modification of surface chemistry, as well as unique optical, mechanical, and rheological performance. One of the most fascinating properties of CNMs is their aqueous suspension rheology, i.e., CNMs helping create viscous suspensions with the formation of percolation networks and chemical interactions (e.g., van der Waals forces, hydrogen bonding, electrostatic attraction/repulsion, and hydrophobic attraction). Under continuous shearing, CNMs in an aqueous suspension can align along the flow direction, producing shear-thinning behavior. At rest, CNM suspensions regain some of their initial structure immediately, allowing rapid recovery of rheological properties. These unique flow features enable CNMs to serve as rheological modifiers in a wide range of fluid-based applications. Herein, the dependence of the rheology of CNM suspensions on test protocols, CNM inherent properties, suspension environments, and postprocessing is systematically described. A critical overview of the recent progress on fluid applications of CNMs as rheology modifiers in some emerging industrial sectors is presented as well. Future perspectives in the field are outlined to guide further research and development in using CNMs as the next generation rheological modifiers.

Hydrogel-Forming Algae Polysaccharides: From Seaweed to Biomedical Applications

With the increasing growth of the algae industry and the development of algae biorefinery, there is a growing need for high-value applications of algae-extracted biopolymers. The utilization of such biopolymers in the biomedical field can be considered as one of the most attractive applications but is challenging to implement. Historically, polysaccharides extracted from seaweed have been used for a long time in biomedical research, for example, agarose gels for electrophoresis and bacterial culture. To overcome the current challenges in polysaccharides and help further the development of high-added-value applications, an overview of the entire polysaccharide journey from seaweed to biomedical applications is needed. This encompasses algae culture, extraction, chemistry, characterization, processing, and an understanding of the interactions of soft matter with living organisms. In this review, we present algae polysaccharides that intrinsically form hydrogels: alginate, carrageenan, ulvan, starch, agarose, porphyran, and (nano)cellulose and classify these by their gelation mechanisms. The focus of this review further lays on the culture and extraction strategies to obtain pure polysaccharides, their structure-properties relationships, the current advances in chemical backbone modifications, and how these modifications can be used to tune the polysaccharide properties. The available techniques to characterize each organization scale of a polysaccharide hydrogel are presented, and the impact on their interactions with biological systems is discussed. Finally, a perspective of the anticipated development of the whole field and how the further utilization of hydrogel-forming polysaccharides extracted from algae can revolutionize the current algae industry are suggested.

Chemical Modification of Reducing End-Groups in Cellulose Nanocrystals

Native plant cellulose has an intrinsic supramolecular structure. Consequently, it can be isolated as nanocellulose species, which can be utilized as building blocks for renewable nanomaterials. The structure of cellulose also permits its end-wise modification, i.e., chemical reactions exclusively on one end of a cellulose chain or a nanocellulose particle. The premises for end-wise modification have been known for decades. Nevertheless, different approaches for the reactions have emerged only recently, because of formidable synthetic and analytical challenges associated with the issue, including the adverse reactivity of the cellulose reducing end and the low abundance of newly introduced functionalities. This Review gives a full account of the scientific underpinnings and challenges related to end-wise modification of cellulose nanocrystals. Furthermore, we present how the chemical modification of cellulose nanocrystal ends may be applied to directed assembly, resulting in numerous possibilities for the construction of new materials, such as responsive liquid crystal templates and composites with tailored interactions.

Nanocellulose: Recent Fundamental Advances and Emerging Biological and Biomimicking Applications

In the effort toward sustainable advanced functional materials, nanocelluloses have attracted extensive recent attention. Nanocelluloses range from rod-like highly crystalline cellulose nanocrystals to longer and more entangled cellulose nanofibers, earlier denoted also as microfibrillated celluloses and bacterial cellulose. In recent years, they have spurred research toward a wide range of applications, ranging from nanocomposites, viscosity modifiers, films, barrier layers, fibers, structural color, gels, aerogels and foams, and energy applications, until filtering membranes, to name a few. Still, nanocelluloses continue to show surprisingly high challenges to master their interactions and tailorability to allow well-controlled assemblies for functional materials. Rather than trying to review the already extensive nanocellulose literature at large, here selected aspects of the recent progress are the focus. Water interactions, which are central for processing for the functional properties, are discussed first. Then advanced hybrid gels toward (multi)stimuli responses, shape-memory materials, self-healing, adhesion and gluing, biological scaffolding, and forensic applications are discussed. Finally, composite fibers are discussed, as well as nanocellulose as a strategy for improvement of photosynthesis-based chemicals production. In summary, selected perspectives toward new directions for sustainable high-tech functional materials science based on nanocelluloses are described.

Tunable dialdehyde/dicarboxylate nanocelluloses by stoichiometrically optimized sequential periodate-chlorite oxidation for tough and wet shape recoverable aerogels

Sequential periodate-chlorite (PC) oxidation has been optimized stoichiometrically according to the non-crystalline content in cellulose to generate a variety of versatile C2,C3 dialdehyde/dicarboxylate nanocelluloses (NCs) while economizing chemical and shear force inputs. The robust primary sodium periodate (NaIO4) oxidation not only regioselectively cleaved the C2-C3 carbon bond to oxidize the vicinal hydroxyls to aldehydes, but also governed the lengths of NCs, i.e., cellulose nanofibrils (PC-CNFs) at near-equal NaIO4 to non-crystalline anhydroglucose unit (AGU) stoichiometry and cellulose nanocrystals (PC-CNCs) at a doubled ratio. Secondary sodium chlorite (NaClO2) oxidation facilely converted C2,C3 dialdehydes to dicarboxylates and, upon deprotonation, facilitated defibrillation to NCs, irrespective of extents of carboxylation or charges. The optimal 0.5 : 1 NaIO4/AGU and 1 : 1 NaClO2/AGU oxidation produced highly uniform 1.26 nm thick, 3.28 nm wide, and ca. 1 μm long PC-CNFs with tunable surface aldehyde (0.71-0.0 mmol g-1) and carboxylate (0.64-1.35 mmol g-1) content at 94-98% yields. The C2-C3 glucosidic ring opening and oxidation along the 110 or 11̄0 crystalline surfaces increased the heterogeneity of the hydrophilic surfaces and flexibility of PC-CNFs to influence their self-assembling into fibrils and amphiphilic superabsorbent aerogels. The ultra-light (ρ = 10.3 mg cm-3) aerogels showed an ultra-high dry specific compression modulus (50.2 kPa mg-1 cm-3) and specific stress (8.2 kPa mg-1 cm-3 at 0.8 strain), cyclic wet compressive behavior, and excellent water-activated shape recovery following 0.8 strain dry compression.

Self-Assembly of Soft Cellulose Nanospheres into Colloidal Gel Layers with Enhanced Protein Adsorption Capability for Next-Generation Immunoassays

Soft cationic core/shell cellulose nanospheres can deform and interpenetrate allowing their self-assembly into densely packed colloidal nanogel layers. Taking advantage of their water-swelling capacity and molecular accessibility, the nanogels are proposed as a new and promising type of coating material to immobilize bioactive molecules on thin films and paper. The specific and nonspecific interactions between the cellulosic nanogel and human immunoglobulin G as well as bovine serum albumin (BSA) are investigated. Confocal microscopy, electroacoustic microgravimetry, and surface plasmon resonance are used to access information about the adsorption behavior and viscoelastic properties of self-assembled nanogels. A significant BSA adsorption capacity on nanogel layers (17 mg m^-2 ) is measured, 300% higher compared to typical polymer coatings. This high protein affinity further confirms the promise of the introduced colloidal gel layer, in increasing sensitivity and advancing a new generation of substrates for a variety of applications, including immunoassays, as demonstrated in this work.

Preparation of Cellulose Nanofibers from Bagasse by Phosphoric Acid and Hydrogen Peroxide Enables Fibrillation via a Swelling, Hydrolysis, and Oxidation Cooperative Mechanism

Due to the natural cellulose encapsulated in both lignin and hemicellulose matrices, as well as in plant cell walls with a compact and complex hierarchy, extracting cellulose nanofibers (CNFs) from lignocellulosic biomass is challenging. In this study, a sustainable high yield strategy with respect to other CNF preparations was developed. The cellulose was liberated from plant cell walls and fibrillated to a 7-22 nm thickness in one bath treatment with H₃PO₄ and H₂O₂ under mild conditions. The cellulose underwent swelling, the lignin underwent oxidative degradation, and the hemicellulose and a small amount of cellulose underwent acid hydrolysis. The CNFs' width was about 12 nm, with high yields (93% and 50% based on cellulose and biomass, respectively), and a 64% crystallinity and good thermal stability were obtained from bagasse. The current work suggests a strategy with simplicity, mild conditions, and cost-effectiveness, which means that this method can contribute to sustainable development for the preparation of CNFs.

Review: Periodate oxidation of wood polysaccharides-Modulation of hierarchies

Periodate oxidation of polysaccharides has transitioned from structural analysis into a modification method for engineered materials. This review summarizes the research on this topic. Fibers, fibrils, crystals, and molecules originating from forests that have been subjected to periodate oxidation can be crosslinked with other entities via the generated aldehyde functionality, that can also be oxidized or reduced to carboxyl or alcohol functionality or used as a starting point for further modification. Periodate-oxidized materials can be subjected to thermal transitions that differ from the native cellulose. Oxidation of polysaccharides originating from forests often features oxidation of structures rather than liberated molecules. This leads to changes in macro, micro, and supramolecular assemblies and consequently to alterations in physical properties. This review focuses on these aspects of the modulation of structural hierarchies due to periodate oxidation.

Partially Oxidized Cellulose grafted with Polyethylene Glycol mono-Methyl Ether (m-PEG) as Electrolyte Material for Lithium Polymer Battery

Herein, a novel cellulose derivative has been synthesized and investigated as a nature-derived solid polymer electrolyte for lithium batteries. Cellulose is oxidized in a two-step process to dicarboxylic acid cellulose to allow for grafting low molecular weight poly(ethylene glycol) monomethyl ether (550 g mol^-1) via Fischer-Speier esterification at the thus obtained carboxyl groups. The chemical structure of the synthesized materials is confirmed by Fourier-transform infrared (FT-IR) and nuclear magnetic resonance (NMR) spectroscopy as well as X-ray diffraction. Incorporating lithium bis(trifluoromethane-sulfonyl)imide (LiTFSI) as conducting salt and N-butyl-N-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide (Pyr₁₄TFSI) ionic liquid as plasticizer results in the realization of an amorphous and solvent-free solid polymer electrolyte. These electrolyte membranes are characterized by high thermal and electrochemical stability and ionic conductivities of about 1×10^-5 S cm^-1 at 20 °C and 2.5×10^-4 S cm^-1 at 80 °C, which enables very stable lithium stripping and plating for more than 800 h.

Fabrication of oxidized bacterial cellulose by nitrogen dioxide in chloroform/cyclohexane as a highly loaded drug carrier for sustained release of cisplatin

Carboxylated bacterial cellulose (OBC) was fabricated by oxidation with nitrogen dioxide in chloroform/cyclohexane and employed as a carrier for sustained release of antitumor substance cisplatin (CDDP). The influence of removing water method, solvent used in the synthesis, concentration of N₂O₄, and duration of the oxidation on content of carboxyl groups in reaction products was established. Due to the possibility of nitrogen dioxide to penetrate into cellulose crystallites, the carboxyl group content of the OBC reaches high values up to 4 mmol/g. In vitro degradation of OBC was determined under simulated physiological conditions. The immobilization of CDDP on OBC was studied in detail. The initial burst release of the drug from the polymer was depressed. The cytotoxicity of CDDP-loaded OBC was evaluated with HeLa cells. The unique structure and properties of OBC make it a great candidate as drug delivery carrier.

Design of dialdehyde cellulose crosslinked poly(vinyl alcohol) hydrogels for transdermal drug delivery and wound dressings

2,3-Dialdehyde cellulose (DAC) was used as an efficient and low-toxicity crosslinker to prepare thin PVA/DAC hydrogel films designed for topical applications such as drug-loaded patches, wound dressings or cosmetic products. An optimization of hydrogel properties was achieved by the variation of two factors - the amount of crosslinker and the weight-average molecular weight (M_w) of the source PVA. The role of each factor to network parameters, mechanical, rheological and surface properties, hydrogel porosity and transdermal absorption is discussed. The best results were obtained for hydrogel films prepared using 0.25 wt% of DAC and PVA with M_w = 130 kDa, which had a high porosity and drug-loading capacity (high water content), mechanical properties allowing easy handling, best adherence to the skin from all tested samples and improved transdermal drug-delivery. Hydrogel films are biocompatible, show no cytotoxicity and have no negative impact on cell growth and morphology in their presence. Furthermore, hydrogels do not support cell migration and attachment to their surface, which should ensure easy removal of hydrogel patches even from wounded or damaged skin after use.

Selective Isolation Methods for Cellulose and Chitin Nanocrystals

This Minireview focuses on the selective isolation methods for the preparation of cellulose nanocrystals (CNCs) and chitin nanocrystals (ChNCs). Various selective preparation strategies with specific preparation conditions and reaction mechanisms are summarized. In particular, these selective reaction routes include controlled acid hydrolysis and selective oxidations at specific positions of cellulose or chitin fibers as well as particular reaction sites of the repeating monosaccharide building blocks of their main chains. These lead to selective cleavage of the ordered and non-ordered regions of cellulose and chitin and result in efficient production of CNCs and ChNCs.

Functionalized cellulose to remove surfactants from cosmetic products in wastewater

A flocculant composed of paper mulberry dicarboxylic cellulose (PM-DCC) made from using paper mulberry (Broussonetia kazinoki Siebold and Zucc.) has been developed to reduce the amount of inorganic coagulants needed to remove surfactants in wastewater. The characteristics of PM and soda pulp were determined according to the degree of polymerization, α-cellulose, lignin, free sugar, and extract contents. FTIR, XRD, the aldehyde content, the carboxyl content and coagulant-flocculation experiments were conducted to confirm the properties of PM-DCC and paper mulberry dialdehyde cellulose (PM-DAC). A dramatic removal efficiency (95.62 %) was revealed when 0.3 % PM-DCC was added into a linear alkylbenzene sulfonate (LAS) solution with 1% FeCl₃·6H₂O at pH 2. This means that PM-DCC contributes to both a lower amount of inorganic coagulant needed and a reduction of water pollution by an ecofriendly method.

Microcrystalline cellulose (MCC) based materials as emerging adsorbents for the removal of dyes and heavy metals - A review

In an attempt to overcome such threats posed by water pollution, various processes ranging from physical, chemical as well as biological were applied to get rid of wastewater pollutants. The simplicity, high efficiency and cheapness of an adsorption process make it the most widely used among various other processes. Adsorbents with different properties were used in the adsorption process but this paper was focused on reviewing various articles published by numerous researchers on the isolation of microcrystalline cellulose (MCC), a popular carbohydrate polymer from lignocellulosic biomass and utilization of MCC based materials as effective adsorbents for the successful removal of dyes and heavy metals from synthetic wastewater. The sudden interest on MCC and MCC-based materials as adsorbents cannot be separated from their excellent properties such as renewability, biodegradability, biocompatibility, economic value, non-toxicity, high mechanical properties and surface area. Upon comparison with established adsorbents reported from literature, MCC-based materials performed excellently well in the adsorption of dyes and heavy metals with Langmuir isotherm and pseudo-second order reported mostly as the best fit models for the generated equilibrium and kinetic data, respectively pointing at the distribution of adsorption sites to be homogeneous as well as the formation of monolayer adsorbate on their surfaces. The various thermodynamic studies reported further revealed the adsorption processes of both dyes and heavy metals onto MCC-based materials to be entropy driven processes, spontaneous, and endothermic. Finally, future research was suggested to focus on optimization to enhance the performance of the MCC-based adsorbents, carrying out the adsorption on real wastewater instead of synthetic ones as well as expanding the range of adsorbates to include other contaminants such as chlorophenols, herbicides, pesticides and others in addition to dyes and heavy metals.

Direct Preparation of Cellulose Nanofibers from Bamboo by Nitric Acid and Hydrogen Peroxide Enables Fibrillation via a Cooperative Mechanism

Separating the fibers, deconstructing both the interlamellar structures and the intermicrofibrils structures in the cell wall, and cleaving the amorphous regions of cellulose (all reached in one bath chemical-assisted treatment), then extracting cellulose nanofibers (CNFs) from biomass, is both challenging and imperative. A simple, cost-effective and green strategy for extracting CNFs from bamboo using nitric acid and hydrogen peroxide (NCHP), to enable fibrillation via a cooperative mechanism, is demonstrated herein. NCHP-CNFs 13.1 ± 2.0 nm wide, with a high aspect ratio, 74% crystallinity, excellent UV resistance and high thermal stability, were successfully extracted by treatment in HNO₃ aqueous solution, at a concentration of 3.2 mol/L, and treatment with 60.00 mmol/g H₂O₂ at 50 °C for 48 h. The yields of NCHP-CNFs reached 73% and 99% based on biomass and cellulose, respectively, due to the high delignification selectivity of OH⁺ and the mild aqueous conditions during the NCHP treatment. These NCHP-CNFs with excellent UV resistance can potentially be applied in the field of UV-resistant coatings, to replace organic and inorganic materials.

Hestekin J. Oxone®-Mediated TEMPO-Oxidized Cellulose Nanomaterials form I and form II

The 2,2,6,6-tetramethylpiperidin-1-oxyl (TEMPO) oxidation of cellulose, when mediated with Oxone^® (KHSO₅), can be performed simply and under mild conditions. Furthermore, the products of the reaction can be isolated into two major components: Oxone^®-mediated TEMPO-oxidized cellulose nanomaterials Form I and Form II (OTO-CNM Form I and Form II). This study focuses on the characterization of the properties of OTO-CNMs. Nanoparticle-sized cellulose fibers of 5 and 16 nm, respectively, were confirmed through electron microscopy. Infrared spectroscopy showed that the most carboxylation presented in Form II. Conductometric titration showed a two-fold increase in carboxylation from Form I (800 mmol/kg) to Form II (1600 mmol/kg). OTO-CNMs showed cellulose crystallinity in the range of 64–68% and crystallite sizes of 1.4–3.3 nm, as shown through XRD. OTO-CNMs show controlled variability in hydrophilicity with contact angles ranging from 16 to 32°, within or below the 26–47° reported in the literature for TEMPO-oxidized CNMs. Newly discovered OTO-CNM Form II shows enhanced hydrophilic properties as well as unique crystallinity and chemical functionalization in the field of bio-sourced material and nanocomposites.

Self-Fibrillating Cellulose Fibers: Rapid In Situ Nanofibrillation to Prepare Strong, Transparent, and Gas Barrier Nanopapers

Cellulose nanofibrils (CNFs) prepared from wood biomass are promising candidates to replace oil-based materials in, for example, packaging applications. However, CNFs’ affinity for water combined with their small size leads to very slow and energy-demanding processes for handling and removal of water. To a large extent, this is the major roadblock that prevents a feasible production of dry CNF-based materials on an industrial scale. In this work, self-fibrillating fibers (SFFs) from wood, where the fibrils can be liberated by external stimuli, were prepared via sequential TEMPO and periodate oxidation reactions. Papers made from these modified fibers using conventional laboratory papermaking methods were then in situ nanofibrillated via a modest pH increase. With a dewatering time of less than 10 s for a 3 g/L dispersion, SFFs represent a major improvement over conventional CNF nanopapers that take approximately 6 h to dewater. Moreover, 100 g/m² nanopapers obtained through in situ fibrillation exhibited comparable, if not superior, properties to those reported for conventionally made CNF films. A tensile strength of 184 MPa, a Young’s modulus of 5.2 GPa, a strain at break of 4.6%, 90% optical transmittance, and an oxygen permeability of 0.7 cm³ μm m^–2 d^–1 kPa^–1 at 50% RH were measured for SFF nanopapers. Furthermore, in situ nanofibrillation of the SFFs can also be achieved from already dried papers, facilitating numerous possibilities in terms of logistics and handling for an industrial scale-up and transportation of nanomaterials. Overall, stimuli-induced SFFs indeed enable a rapid production of strong, transparent, gas barrier nanopapers, which likely can be industrially scaled up and eventually compete with the oil-based plastics in the market for packaging materials.

Waste paper: An underutilized but promising source for nanocellulose mining

Nanocellulose has achieved an inimitable place and value in nano-materials research sector. Promising and exclusive physical, chemical and biological properties of nanocellulose make it an attractive and ideal material for various high end-user applications. Conventionally, the base material for nanocellulose i.e. cellulose is being extracted from various lignocellulosic raw materials (like wood, agro-industrial-residues, etc.) using pulping followed by bleaching sequences. As an alternate to lignocellulosic raw materials, waste paper also showed potential as a competent raw material due to its abundant availability and high cellulosic content (60-70%) with comparatively less hemicelluloses (10-20%) and lignin (5-10%) without any harsh treatments. The production yields of nanocellulose were reported to vary from 1.5% to 64% depending upon the waste papers and treatments given. The diameters of these nanocelluloses were reported in the range of 2-100 nm and crystallinity range around 54-95%. Thermal degradation of waste paper nanocellulose was varied from 187 °C to 371 °C. Although these properties are comparable with the nanocellulose obtained from lignocellulosic raw materials, yet waste paper is an underutilized source for nanocellulose preparation due to its ordinary fate of recycling, dumping and incineration. In the sight of necessity and possibility of waste paper utilization, this article reviews the outcomes of research carried out for preparation of nanocellulose using waste paper as a source of cellulose. There is a need of sincere investigation to convert this valuable waste to wealth i.e. waste papers to nanocellulose, which will be helpful in solid waste management to protect environment in economical way.

A Thixotropic, Cell-Infiltrative Nanocellulose Hydrogel That Promotes in Vivo Tissue Remodeling

Injectable gels have been used in minimally invasive surgery for tissue regeneration and treatment of inflammatory diseases. However, polymeric hydrogels often fail in cell infiltration, because of the presence of dense, cross-linked molecular networks and a lack of bioactivity, which causes delayed tissue remodeling. Here, we report a thixotropic, cell-infiltrative hydrogel of biofunctionalized nanocellulose that topologically enhances cell infiltration and biochemically upregulates cellular activity for the promotion of tissue remodeling. Biodegradable, sulfonated nanocellulose forms a nanofibrous hydrogel, mimicking cellular microenvironments through cross-linking between nanocellulose and gelatin. Resulting nanocellulose hydrogels showed thixotropy, allowing for single syringe injection. Nanofiber-based hydrogels possess high molecular permeability, which is due to nanoporous structures. Sulfonate groups on nanocellulose increase protein adsorption and induce cellular extension in vitro. Highly sulfonated nanocellulose hydrogels enhanced cell infiltration and vascularization upon implantation into rats. Macrophage polarization to M2 was observed in nanocellulose hydrogels, which may be involved in tissue remodeling. Injectable, biofunctionalized nanocellulose gels have enormous potential as artificial biomatrices to heal inflammatory diseases through manipulation of the immune system and promotion of tissue remodeling.

Interfacial Nanoparticle Complexation of Oppositely Charged Nanocelluloses into Functional Filaments with Conductive, Drug Release, or Antimicrobial Property

Construction of colloidal nanoparticles (NPs) into advanced functional nanocomposites and hybrids with the predesigned hierarchical structure and high-performance is attractive, especially for natural biological nanomaterials, such as proteins and polysaccharides. Herein, a simple and sustainable approach called interfacial NP complexation (INC) was applied to construct diverse functional (conductive, drug-loaded, or antimicrobial) nanocomposite filaments from oppositely charged colloidal nanocelluloses. By incorporating different additives during the INC process, including multiwalled carbon nanotube, an antitumor drug (doxorubicin hydrochloride), and metal (silver) NPs (Ag NPs), high-performance functional continuous filaments were synthesized, and their potential applications in electronics, drug delivery, and antimicrobial materials were investigated, respectively. This novel INC method based on charged colloidal NPs opens new avenues for building various functional filaments for a diversity of end uses.

Composites of nanofibrillated cellulose with clay minerals: A review

Biopolymers-based composites are, in general, environmentally friendly materials, which can be obtained from renewable sources. Some of them can also present promising properties to be used in food packaging and electronic devices, being thus logical substitutes to petroleum-based polymers, specifically plastics. Cellulose nanofibrils (CNF) obtained by chemical/enzymatic pre-treatments followed by a mechanical treatment appear as a new suitable biomaterial. However, CNF are still quite expensive materials, due to the required chemicals/equipment/energy involved, and additionally, they present some limitations such as high hydrophilicity/high water vapour permeability. The combination of CNF with clay minerals, such as montmorillonite or kaolinite, as widely available geo-resources, represents an excellent way to reduce the amount of CNF used, enabling the production of valuable materials and reducing costs; and, at the same time it is possible to improve the characteristics of the formed materials, such as mechanical, gas barrier and fire retardancy properties, if appropriate conditions of preparation are used. Nevertheless, to obtain hybrid CNF/clay composites with superior properties it is necessary to ensure a good dispersion of the inorganic material in the CNF suspension and a good compatibility among the inorganic and organic components. To fulfil this goal, several strategies can be considered, including physical treatments of the suspensions, CNF and clay surface chemical modifications, and the use of a coupling agent. In this review article, the state-of-the-art on a new emerging generation of composites (films, foams or coatings) based on nanofibrillated cellulose and nanoclay, with focus on strategies for their preparation and most relevant achievements is critically reviewed, bearing in mind their potential application as substitutes for common plastics. A third component has been eventually added to these organic-inorganic hybrids, e.g., chitosan, carboxymethylcellulose, borate or epoxy resin, to enhance specific characteristics of the material. Some general background on the production of different types of CNF and their main properties is previously provided.

Recovery of Gold from Chloride Solution by TEMPO-Oxidized Cellulose Nanofiber Adsorbent

The goal of this study was to assess the sustainability of a modified cellulose nanofiber material for the recovery of precious gold from chloride solution, with a special focus on gold recovery from acidic solutions generated by cupric and ferric chloride leaching processes. TEMPO-oxidized cellulose nanofiber in hydrogel (TOCN), dry (H-TOCN, F-TOCN) and sheet form (S-TOCN) was examined for gold adsorptivity from chloride solution. Additionally, this work describes the optimum conditions and parameters for gold recovery. The data obtained in this investigation are also modeled using kinetic (pseudo first-order and pseudo second-order), isotherm best fit (Freundlich, Langmuir and Langmuir-Freundlich), and thermodynamic (endothermic process) parameters. Results demonstrate that high levels of gold removal can be achieved with TEMPO-oxidized cellulose nanofibers (98% by H-TOCNF) and the interaction characteristics of H-TOCN with gold suggests that other precious metals could also be efficiently recovered.

Osteoclast-Responsive, Injectable Bone of Bisphosphonated-Nanocellulose that Regulates Osteoclast/Osteoblast Activity for Bone Regeneration

An injectable bone may serve as a minimally invasive therapy for large orthopedic defects and osteoporosis and an alternative to allografting and surgical treatment. However, conventional bone substitutes lack the desirable biodegradability, bioresponsibility, and functionality to regulate the bone regeneration process. Here, we report an injectable, bioresponsive bone composed of bisphosphonate-modified nanocellulose (pNC) as a bone substitute for bone regeneration. Composites composed of nanofibrillated cellulose and β-tricalcium phosphate (β-TCP) mimic bone structures in which apatite reinforces collagen fibrils. Bisphosphonate groups on nanocellulose provide reversible, physical cross-linking with β-TCP, apatite formation, binding property to bone, and pH responsiveness. When the pH drops to ∼4.5, which corresponds to an osteoclast-induced pH decrease, pNC-β-TCP composite degrades and releases pNC. pNC suppresses osteoclast formation and pit formation. This osteoclast-responsive property allows for controlling the degradation rate of the composite. Moreover, the composite of pNC, α-tricalcium phosphate (α-TCP), and β-TCP enhances osteoblast differentiation. This injectable bone substitute of pNC that regulates osteoclast/osteoblast activity has enormous potential for the treatment of bone diseases and prevention of locomotive syndrome.

Recyclable and Mendable Cellulose-Reinforced Composites Crosslinked with Diels⁻Alder Adducts

Owing to their natural abundance and exceptional mechanical properties, cellulose fibers (CFs) have been used for reinforcing polymers. Despite these merits, dispersing hydrophilic CFs in a hydrophobic polymer matrix is challenging. To address this, an amphiphilic ammonium salt was employed as the dispersant for CFs in this study. The hydrophobic CFs were mixed with a healable polymer to produce CF-reinforced composites. As the thermosetting polymer was crosslinked with Diels–Alder (DA) adducts, it was mended and recycled via a retro DA reaction at 120 °C. Interestingly, the CF-reinforced polymer composites were mended and recycled as well. When 5 wt % of the hydrophobic CFs was added to the polymer, maximum tensile strength, elongation at break, Young’s modulus, and toughness increased by 70%, 183%, 75%, and 420%, respectively. After recycling, the CF-reinforced composites still featured better mechanical properties than recycled polymer.

Photooxidation of triarylphosphines under aerobic conditions in the presence of a gold(iii) complex on cellulose extracted from Carthamus tinctorius immobilized on nanofibrous phosphosilicate

Triarylphosphines were converted to the corresponding oxides via photooxidation as a novel method.

Recycling of isopropanol for cost-effective, environmentally friendly production of carboxymethylated cellulose nanofibrils

An approach to recycling isopropanol used in the carboxymethylation of pulp fiber was investigated as a cost-effective and environmentally friendly method of producing cellulose nanofibrils (CNF). Carboxymethylation of pulp fiber was carried out using isopropanol (IPA) as the sole solvent. IPA was recovered after carboxymethylation reaction and recycled in the next carboxymethylation reaction. Simple recycling of IPA decreased the reaction efficiency of carboxymethylation due to the increase of water content in the IPA. To dehydrate the recovered IPA, a 4 Å molecular sieve was used as a drying material. It was shown that dehydration restored carboxymethylation efficiency to the same level as when fresh IPA was used. The characteristics of the carboxymethylated CNFs produced using the recycled IPA were evaluated, including fibrillation tendency, average width, and width distribution, and it was shown that the use of recycled IPA after dehydration treatment did not cause any changes in carboxymethylated CNF properties. Recycling IPA after simple dehydration using a molecular sieve is thus a cost-effective and environmentally friendly method of producing carboxymethylated CNF.