Urban wastewater treatment plants as hotspots for the release of antibiotics in the environment: a review

Determination of tetracycline residues in potatoes and soil by LC-MS/MS: Method development, validation, and risk assessment

A method utilizing liquid-liquid extraction (LLE) coupled with liquid chromatography-tandem mass spectrometry (LC-MS/MS) was developed and validated according to the Commission Implementing Regulation (CIR) EU 2021/808 for quantifying four tetracyclines (TCs) in potatoes and soil. The method demonstrated recovery values ranging from 70 to 121% and precision (repeatability and within-laboratory reproducibility), with coefficient of variation (CV) values below 18% for all TCs in both matrices. The limits of quantification (LOQs) for the TCs ranged from 0.90 to 1.87 μg/kg in potatoes and from 0.68 to 1.25 μg/kg in soil. The decision limit (CCα) and detection capability (CCβ) ranged from 10.4 to 12.3 μg/kg and 11.9 to 14.3 μg/kg, respectively. Analysis of 538 potato and soil samples from Egyptian farms revealed a 13.2% occurrence of TC residues, with a higher frequency in soil (19.33%) than in potatoes (7.06%). Target hazard quotient (THQ) values indicated that TC residues in potatoes do not pose a health risk to Egyptian consumers.

Efficient removal of antibiotic resistance genes and of enteric bacteria from reclaimed wastewater by enhanced Soil Aquifer Treatments

Soil Aquifer Treatment (SAT) is a robust technology to increase groundwater recharge and to improve reclaimed water quality. SAT reduces dissolved organic carbon, contaminants of emerging concern, nutrients, and colloidal matter, including pathogen indicators, but little is known about its ability to reduce loads of antibiotic resistance genes (ARGs) from reclaimed waters. Here we test six pilot SAT systems to eliminate various biological hazards from the secondary effluents of a wastewater treatment plant (WWTP), equipped with reactive barriers (RBs) including different sorptive materials. Using flow cytometry, qPCR and 16S rRNA gene amplicon sequencing methods, we determined that all six SAT systems reduced total loads of bacteria by 80 to 95 % and of clinically relevant ARGs by 85 to 99.9 %. These efficiencies are similar to those reported for UV/oxidation or membrane-based tertiary treatments, which require much more energy and resources. The presence and composition of reactive barriers, the season of sampling (June 2020, October 2020, and September 2021), or the flow regime (continuous versus pulsating) did not affect ARG removal efficiency, although they did alter the microbial community composition. This suggests that an adequate design of the SAT reactive barriers may significantly increase their performance. Under a mechanistic point of view, we observed an ecological succession of bacterial groups, linked to the changing physical-chemical conditions along the SAT, and likely correlated to the removal of ARGs. We concluded that SAT is as cost-efficient technology able to dramatically reduce ARG loads and other biological hazards from WWTP secondary effluents.

Antibiotics in surface waters of the south caspian sea: Occurrence, spatial distribution and ecological risks

Marine environments play a crucial role in absorbing land-based pollutants. While the presence of pharmaceuticals in various marine settings worldwide is well-documented, there is a lack of data regarding pharmaceutical occurrence in the south Caspian Sea. This study examined the presence and spatial distribution of 14 antibiotics in the surface waters of the south Caspian Sea during summer of 2020. Our findings revealed that antibiotics were widespread in this region, with total concentrations reaching up to 3499.9 ng/L. The detection frequencies of the studied antibiotics ranging from 22.0% to 67.0%. Trimethoprim, ofloxacin, and sulfamethoxazole were commonly detected, with detection frequencies exceeding 56.0%. Ofloxacin (235.8 ng/L) and Erythromycin-H2O (2.3 ng/L) had the highest and lowest detected concentrations among the studied antibiotics. Furthermore, fluoroquinolones exhibited notably higher concentrations compared to other antibiotic groups. The highest concentrations of most antibiotics were found in surface waters collected from Ramsar and Chalus stations, located in the middle section of the coastline. Across all transects, the distribution of antibiotics exhibited a decreasing trend towards the sea, indicating that coastal and inland aquaculture, as well as municipal wastewaters, were probably the primary sources of antibiotics in this area. Multivariate analysis revealed that antibiotics, phosphate, nitrate, and COD were all positively correlated with stations Ram-1, Ram-20, Cha-1, Cha-20, and Tor-1, where the highest antibiotic levels were recorded. Risk assessment indicated that clarithromycin, ofloxacin and enrofloxacin posed medium to high risks to aquatic organisms. These findings offer essential baseline information and valuable insights for the comparative assessment of future antibiotic data in the south Caspian Sea.

Occurrence, distribution, and correlation of antibiotics in the aquatic ecosystem of Poyang Lake Basin, China

The widespread existence and persistence of antibiotics in the aquatic environment, and their extensive ecological risks, have attracted considerable attention. The objective of this study was to evaluate the occurrence and distribution of 25 antibiotics in environmental and biological samples from Poyang Lake Basin in China. SPE-HPLC-MS/MS was used to quantify the concentrations in different matrices. The total concentrations ranged from 144 to 933 ng/L in the water and 346 to 1154 ng/g in the sediment. In the spatial distribution analysis of this basin, the concentrations in the Ganjiang River were generally higher than those in Poyang Lake. The seasonal distribution in the wet and dry seasons showed comparatively higher concentrations during the dry season than the wet season. Additionally, antibiotics were found in various hydrophytes and animals, and the bioconcentration factor values followed the order: emergent plants > floating plants > submerged plants and benthic organisms > ducks > fish. Moreover, correlations among different matrices showed that antibiotics in viviparid snails were significantly positively correlated with those in ducks, and negatively correlated with those in carps, indicating the transmission relationship through the food chain. The results showed the trophic transfer of antibiotics in the food web and their potential environmental impacts on Poyang Lake Basin need constant attention.

Use of reclaimed municipal wastewater in agriculture: Comparison of present practice versus an emerging paradigm of anaerobic membrane bioreactor treatment coupled with hydroponic controlled environment agriculture

Advancements in anaerobic membrane bioreactor (AnMBR) technology have opened up exciting possibilities for sustaining precise water quality control in wastewater treatment and reuse. This approach not only presents an opportunity for energy generation and recovery but also produces an effluent that can serve as a valuable nutrient source for crop cultivation in hydroponic controlled environment agriculture (CEA). In this perspective article, we undertake a comparative analysis of two approaches to municipal wastewater utilization in agriculture. The conventional method, rooted in established practices of conventional activated sludge (CAS) wastewater treatment for soil/land-based agriculture, is contrasted with a new paradigm that integrates AnMBR technology with hydroponic (soilless) CEA. This work encompasses various facets, including wastewater treatment efficiency, effluent quality, resource recovery, and sustainability metrics. By juxtaposing the established methodologies with this emerging synergistic model, this work aims to shed light on the transformative potential of the integration of AnMBR and hydroponic-CEA for enhanced agricultural sustainability and resource utilization.

Effect driven prioritization of contaminants in wastewater treatment plants across China: A data mining-based toxicity screening approach

A diversity of contaminants of emerging concern (CECs) are present in wastewater effluent, posing potential threats to receiving waters. It is urgent for a holistic assessment of the occurrence and risk of CECs related to wastewater treatment plants (WWTP) on national and regional scales. A data mining-based risk prioritization method was developed to collect the reported contaminants and their respective concentrations in municipal and industrial WWTPs and their receiving waters across China over the past 20 years. A total of 10,781 chemicals were reported in 8336 publications, of which 1037 contaminants were reported with environmental concentrations. While contaminant categories varied across WWTP types (municipal vs. industrial) and regions, pharmaceuticals and cyclic hydrocarbons were the most studied CECs. Contaminant composition in receiving water was closer to that in municipal than industrial WWTPs. Publications on legacy pesticides and polycyclic aromatic hydrocarbons in WWTP decreased recently compared to the past, while pharmaceuticals and perfluorochemicals have received increasing attention, showing a changing concern over time. Detection frequency, concentration, removal efficiency, and toxicity data were integrated for assessing potential risks and prioritizing CECs on national and regional scales using an environmental health prioritization index (EHPi) approach. Among 666 contaminants in municipal WWTP effluent, trichlorfon and perfluorooctanesulfonic acid were with the highest EHPi scores, while 17ɑ-ethinylestradiol and bisphenol A had the highest EHPi scores among 304 contaminants in industrial WWTPs. The prioritized contaminants varied across regions, suggesting a need for tailoring regional measures of wastewater treatment and control.

Self-supporting three-dimensional CuNi-Sb-SnO2 anode with ultra-long service life for efficient removal of antibiotics in wastewater

Electrochemical ozone production (EOP) is a promising technology for the removal of contaminants in wastewater. However, traditional two-dimensional anodes for EOP are restricted by their reliance on substrates and limited surface area, thus exhibiting poor stability and efficiency. Herein, a novel three-dimensional Sb-SnO2 with Cu and Ni co-doped (3D CuNi-ATO) was synthesized via a facile pressing-sintering method without the Ti substrate. 3D CuNi-ATO had a specific surface area two orders of magnitude higher than conventional CuNi-ATO/Ti, as well as the significant capability of EOP that differs from intrinsic 3D ATO. This endowed 3D CuNi-ATO with the capability to remove tetracycline with a pseudo-first-order rate constant of 0.033 min-1 under a low current density of 5 mA cm-2 within 120 min, which was far more efficient than that by 3D ATO and other two-dimensional anodes reported. The 3D CuNi-ATO was confirmed stable in 100 cycles and had an accelerated service lifetime of over 1100 h versus 83 h of CuNi-ATO/Ti. The degradation of tetracycline in complex matrix and flow-through reactors further revealed the promising potential of 3D CuNi-ATO to be applied in scenarios of practical application and continuous high-rate treatment.

Tetracycline and quinolone contamination mediate microbial and antibiotic resistant gene composition in epiphytic biofilms of mesocosmic wetlands

The fate and ecological impact of antibiotics on aquatic ecosystems have not been properly elucidated in mesocosm wetlands scale. This study explored how tetracyclines (TCs, including tetracycline TC and oxytetracycline) and fluoroquinolones (QNs, including ciprofloxacin CIP and levofloxacin) affect mesocosm wetlands vegetated by V. spiralis, focusing on their impact on epiphytic biofilm microbial communities and antibiotic resistance genes (ARGs). Results showed that submerged plants absorbed more antibiotics than sediment. Both TCs and QNs disrupted microbial communities in different ways and increased eukaryotic community diversity in a concentration-dependent manner (2-4 mg/L for CIP, 4-8 mg/L for TC). TCs mainly inhibited epiphytic bacteria, while CIP increased bacterial phyla abundance. TC reduced Cyanobacteriota, Acidobacteriota, and Patescibacteria but increased Bacillota, Bacteroidota, and Armatimonadota. In contrast, CIP reduced Bacteroidota, Cyanobacteriota, and Gemmatimonadota but increased Bacillota, Planctomycetota, and Acidobacteriota. Significant differences in ARG profiles were observed between QNs and TCs, with TCs having a more substantial effect on ARGs due to their stronger impact on bacterial communities. Both antibiotics raised ARG levels with higher concentrations, particularly for multidrug resistance, tetracyclines, trimethoprim, sulfonamides, aminoglycosides, and fosfomycin, emphasizing their role in antimicrobial resistance. The study suggests that antibiotics can either stimulate or inhibit ARGs depending on their effects on bacterial communities. This study provides key evidence on the ecological mechanisms underlying the impact of TCs and QNs on epiphytic microbes of mesocosm wetlands.

Key role of NH4+-N in the removal of oxacillin during managed aquifer recharge: Reconsidering the recharge limitation

Frequent occurrence of trace antibiotics in reclaimed water is concerning, which inevitably causes aquifer contamination in the case of managed aquifer recharge (MAR). Global governments have formulated strict reclaimed water standards to ensure the safety of water reuse. Recent studies have found that improved antibiotics removal is intimately associated with high ammonia-oxidizing activity. However, the role of NH4+-N in the removal of residual antibiotics of reclaimed water during MAR remains unknown. NH4+-N removal and the effects of ammonia oxidation on antibiotics biodegradation in the aquifer are the most significant facts for solving the above collision. In this work, the effects of NH4+-N (0, 1 and 5 mg/L) in a model refractory antibiotic (oxacillin (OXA), 100 μg/L) attenuation were deciphered by employing three individual simulated MAR columns, which so called N0, N1 and N5. The results showed that 5 mg/L NH4+-N in influent upregulated the abundance of amo genes by 28.9 %-68.0 % in N5. And the enriched functional genes encoding key degradation enzymes enhanced the OXA removal by 18.7 % and alleviated the oxidative stress caused by antibiotics. Subsequently, antibiotic resistance genes (ARGs), mobile gene elements (MGEs) and human bacterial pathogens (HBPs) abundance were all significantly decreased. Moreover, the intimate association between ammonia-oxidizing microorganisms (AOM) and candidate OXA degraders based on microbial network analysis further supported the significance of AOM on OXA biodegradation. This study provides comprehensive evidence that appropriate amounts of NH4+-N are beneficial in antibiotics and antibiotic resistance risk reduction, providing compelling insights for refine NH4+-N recharge limitation.

Reducing residual chlortetracycline in wastewater using a whole-cell biocatalyst

Antibiotic contamination has become an increasingly important environmental problem as a potentially hazardous emergent and recalcitrant pollutant that poses threats to human health. In this study, manganese peroxidase displayed on the outer membrane of Escherichia coli as a whole-cell biocatalyst (E. coli MnP) was expected to degrade antibiotics. The manganese peroxidase activity of the whole-cell biocatalyst was 13.88 ± 0.25 U/L. The typical tetracycline antibiotic chlortetracycline was used to analyze the degradation process. Chlortetracycline at 50 mg/L was effectively transformed via the whole-cell biocatalyst within 18 h. After six repeated batch reactions, the whole-cell biocatalyst retained 87.2 % of the initial activity and retained over 87.46 % of the initial enzyme activity after storage at 25°C for 40 days. Chlortetracycline could be effectively removed from pharmaceutical and livestock wastewater by the whole-cell biocatalyst. Thus, efficient whole-cell biocatalysts are effective alternatives for degrading recalcitrant antibiotics and have potential applications in treating environmental antibiotic contamination.

Nature-based solutions for antibiotics and antimicrobial resistance removal in tertiary wastewater treatment: Microbiological composition and risk assessment

This field-scale study evaluates the seasonal effectiveness of employing nature-based solutions (NBSs), particularly surface flow and horizontal subsurface flow constructed wetland configurations, as tertiary treatment technologies for the removal of antibiotics (ABs) and antibiotic resistance genes (ARGs) compared to a conventional treatment involving UV and chlorination. Out of the 21 monitored ABs, 13 were detected in the influent of three tertiary wastewater treatments, with concentrations ranging from 2 to 1218 ng·L-1. The ARGs sul1 and dfrA1 exhibited concentrations ranging from 1 × 105 to 9 × 106 copies/100 mL. NBSs were better at reducing ABs (average 69 to 88 %) and ARGs (2-3 log units) compared to the conventional tertiary system (average 36 to 39 % and no removal to 2 log units) in both seasons. Taxonomic compositions in influent water samples shifted from wastewater-impacted communities (Actinomycetota and Firmicutes) to a combination of plant rhizosphere-associated and river communities in NBS effluents (Alphaproteobacteria). In contrast, the conventional technology showed no substantial differences in community composition. Moreover, NBSs substantially reduced the ecotoxicological risk assessment (cumulative RQs). Furthermore, NBSs reduced the ecotoxicological risk (cumulative RQs) by an average of over 70 % across seasons, whereas the benchmark technology only achieved a 6 % reduction. In conclusion, NBSs present a robust alternative for minimizing the discharge of ABs and ARGs into surface water bodies.

Recent advances in environmental antibiotic resistance genes detection and research focus: From genes to ecosystems

Antibiotic resistance genes (ARGs) persistence and potential harm have become more widely recognized in the environment due to its fast-paced research. However, the bibliometric review on the detection, research hotspot, and development trend of environmental ARGs has not been widely conducted. It is essential to provide a comprehensive overview of the last 30 years of research on environmental ARGs to clarify the changes in the research landscape and ascertain future prospects. This study presents a visualized analysis of data from the Web of Science to enhance our understanding of ARGs. The findings indicate that solid-phase extraction provides a reliable method for extracting ARG. Technological advancements in commercial kits and microfluidics have facilitated the efficacy of ARGs extraction with significantly reducing processing times. PCR and its derivatives, DNA sequencing, and multi-omics technology are the prevalent methodologies for ARGs detection, enabling the expansion of ARG research from individual strains to more intricate microbial communities in the environment. Furthermore, due to the development of combination, hybridization and mass spectrometer technologies, considerable advancements have been achieved in terms of sensitivity and accuracy as well as lowering the cost of ARGs detection. Currently, high-frequency terms such as "Antibiotic Resistance, Antibiotics, and Metagenomics" are the center of attention for study in this area. Prominent topics include the investigation of anthropogenic impacts on environmental resistance, as well as the dynamics of migration, dissemination, and adaptation of environmental ARGs, etc. The research on environmental ARGs has made significant advancements in the fields of "Microbiology" and "Biotechnology Applied Microbiology". Over the past decade, there has been a notable increase in the fields of "Environmental Sciences Ecology" and "Engineering" with a similar growth trend observed in "Water Resources". These three domains are expected to continue driving extensive study within the realm of environmental ARGs.

Comprehensive analysis and risk assessment of Antibiotic contaminants, antibiotic-resistant bacteria, and resistance genes: Patterns, drivers, and implications in the Songliao Basin

The pervasive use of antibiotics has raised substantial environmental concerns, especially regarding their temporal and spatial distribution across diverse water systems. This study addressed the gap in comprehensive research on antibiotic contamination during different hydrological periods, focusing on the Jilin section of the Songliao Basin in Northeast China, an area with severe winter ice cover. The study examined the occurrence, distribution, influencing factors, and potential ecological risks of prevalent antibiotic contaminants. Findings revealed antibiotic concentrations ranging from 239.64 to 965.81 ng/L, with antibiotic resistance genes (ARGs) at 5.22 × 10-2 16S rRNA-1 and antibiotic-resistant bacteria (ARB) up to 5.76 log10 CFU/mL. Ecological risk assessments identified significant risks to algae from oxytetracycline, erythromycin, and amoxicillin. Redundancy analysis and co-occurrence networks with ordinary least squares (OLS) demonstrated that the dispersion of ARGs and ARB is significantly influenced by environmental factors such as total organic carbon (TOC), total phosphorus (TP), total nitrogen (TN), fluoride (F⁻), and nitrate (NO₃⁻). These elements, along with mobile genetic elements (MGEs), play crucial roles in ARG patterns (R2 = 0.94, p ≤ 0.01). This investigation offers foundational insights into antibiotic pollution dynamics in cold climates, supporting the development of targeted mitigation strategies for aquatic systems.

Antibiotic Residues and Resistance in Three Wastewater Treatment Plants in Romania

This study evaluates antibiotic residues and bacterial loads in influent and effluent samples from three wastewater treatment plants (WWTPs) in Romania, across four seasons from 2021 to 2022. Analytical methods included solid-phase extraction and high-performance liquid chromatography (HPLC) to quantify antibiotic concentrations, while microbiological assays estimated bacterial loads and assessed antibiotic resistance patterns. Statistical analyses explored the impact of environmental factors such as temperature and rainfall on antibiotic levels. The results showed significant seasonal variations, with higher antibiotic concentrations in warmer seasons. Antibiotic removal efficiency varied among WWTPs, with some antibiotics being effectively removed and others persisting in the effluent, posing high environmental risks and potential for antibiotic resistance development. Bacterial loads were higher in spring and summer, correlating with increased temperatures. Eight bacterial strains were isolated, with higher resistance during warmer seasons, particularly to amoxicillin and clarithromycin.

General performance, kinetic modification, and key regulating factor recognition of microalgae-based sulfonamide removal

Sulfonamides have been widely detected in water treatment plants. Advanced wastewater treatment for sulfonamide removal based on microalgal cultivation can reduce the ecological risk after discharge, achieve carbon fixation, and simultaneously recover bioresource. However, the general removal performance, key factors and their impacts, degradation kinetics, and potential coupling technologies have not been systematically summarized. To guide the construction and enhance the efficient performance of the purification system, this study summarizes the quantified characteristics of sulfonamide removal based on more than 100 groups of data from the literature. The biodegradation potential of sulfonamides from different subclasses and their toxicity to microalgae were statistically analyzed; therefore, a preferred option for further application was proposed. The mechanisms by which the properties of both sulfonamides and microalgae affect sulfonamide removal were comprehensively summarized. Thereafter, multiple principles for choosing optimal microalgae were proposed from the perspective of engineering applications. Considering the microalgal density and growth status, a modified antibiotic removal kinetic model was proposed with significant physical meaning, thereby resulting in an optimal fit. Based on the mechanism and regulating effect of key factors on sulfonamide removal, sensitive and feasible factors (e.g., water quality regulation, other than initial algal density) and system coupling were screened to guide engineering applications. Finally, we suggested studying the long-term removal performance of antibiotics at environmentally relevant concentrations and toxicity interactions for further research.

Using Zeolite Materials to Remove Pharmaceuticals from Water

Pharmaceutical drugs, including antibiotics and hormonal agents, pose a significant threat to environmental and public health due to their persistent presence in aquatic environments. Colistin (KOL), fluoxetine (FLUO), amoxicillin (AMO), and 17-alpha-ethinylestradiol (EST) are pharmaceuticals (PhCs) that frequently exceed regulatory limits in water and wastewater. Current removal methods are mainly ineffective, necessitating the development of more efficient techniques. This study investigates the use of synthetic zeolite (NaP1_FA) and zeolite-carbon composites (NaP1_C), both derived from fly ash (FA), for the removal of KOL, FLUO, AMO, and EST from aquatic environments. Batch adsorption experiments assessed the effects of contact time, adsorbent dosage, initial concentration, and pH on the removal efficiency of the pharmaceuticals. The results demonstrated that NaP1_FA and NaP1_C exhibited high removal efficiencies for all tested pharmaceuticals, achieving over 90% removal within 2 min of contact time. The Behnajady-Modirshahla-Ghanbary (BMG) kinetic model best described the adsorption processes. The most effective sorption was observed with a sorbent dose of 1-2 g L-1. Regarding removal efficiency, the substances ranked in this order: EST was the highest, followed by AMO, KOL, and FLUO. Sorption efficiency was influenced by the initial pH of the solutions, with optimal performance observed at pH 2-2.5 for KOL and FLUO. The zeolite-carbon composite NaP1_C, due to its hydrophobic nature, showed superior sorption efficiency for hydrophobic pharmaceuticals like FLUO and EST. The spectral analysis reveals that the primary mechanism for immobilizing the tested PhCs on zeolite sorbents is mainly due to physical sorption. This study underscores the potential of utilizing inexpensive, fly ash-derived zeolites and zeolite-carbon composites to remove pharmaceuticals from water effectively. These findings contribute to developing advanced materials for decentralized wastewater treatment systems, directly addressing pollution sources in various facilities.

Micropollutants (ciprofloxacin and norfloxacin) remediation from wastewater through laccase derived from spent mushroom waste: Fate, toxicity, and degradation

Fluoroquinolone antibiotics frequently found in environmental matrices (wastewater treatment plants, hospital wastewater, industrial wastewater and surface wastewater) causes potential threat to the environment. Enzymatic treatment for degradation of antibiotics from environmental matrices is a green and sustainable approach. Focusing on this, this study aimed to degrade two frequently found fluroquinolone emergent pollutants, ciprofloxacin and norfloxacin from wastewater. The trinuclear cluster of copper ions present in laccase has the ability to effectively remove organic micropollutants (OMPs). The uniqueness of this study is that it utilizes laccase enzyme extracted from spent mushroom waste (SMW) of P. florida for degradation of ciprofloxacin and norfloxacin and to achieve highest degradation efficiency various parameters were tweaked such as pH (3-6), temperature (30 °C and 50 °C), and ABTS (0.05, 0.6, and 1 mM) concentration. The results showed that the most effective degradation of ciprofloxacin (86.12-75.94%) and norfloxacin (83.27-65.94%) was achieved in 3 h at pH 4.5, temperature 30 °C, and 2,2'-azino-bis 3-ethylbenzothiazoline-6-sulfonic acid (ABTS), 0.05 mM concentration. Nevertheless, achieving degradation at 50 °C for both antibiotics, indicates thermostability nature of laccase (P. florida). Further, the fate of transformed products obtained from laccase mediated degradation was confirmed by liquid chromatography (LC-MS). Both the antibiotics undergo decarboxylation, depiperylyzation, dealkylation and defluorination as a result of laccase-mediated bond breakage. Anti-microbial activity of the biodegraded products was monitored by residual anti-bacterial toxicity test (E. coli and Staphylococcus aureus). The biodegraded products were found to be non-toxic and resulted in the growth of E. coli and Staphylococcus aureus, as determined by the agar-diffusion method. Moreover, the storage stability of laccase was determined for 28-day duration at varying pH (3-10) and temperature (4-50 °C). The maximum storage stability was obtained at pH 4.5 and temperature 30 °C. Therefore, utilizing SMW for the degradation of OMPs from wastewater not only benefits in degradation but also reuses SMW agro waste, shedding light on agro waste management. Thus, SMW is a one-pot solution for both OMPs biodegradation and circularity in the economy.

Impact of earthworms on suppressing dissemination of antibiotic resistance genes during vermicomposting treatment of excess sludge

Earthworms play a crucial role in suppressing the dissemination of antibiotic resistance genes (ARGs) during vermicomposting. However, there is still a lack of how earthworms influence the spread of ARGs. To address this gap, a microcosm experiment was conducted, incorporating earthworms and utilizing metagenomics and quantitative PCR to assess the impact of earthworms on microbial interactions and the removal of plasmid-induced ARGs. The findings revealed that vermicomposting led to a reduction in the relative abundance of ARGs by altering microbial communities and interactions. Significantly, vermicomposting demonstrated an impressive capability, reducing 92% of ARGs donor bacteria and impeding the transmission of 94% of the RP4 plasmid. Furthermore, through structural equation model analysis, it was determined that mobile genetic elements and environmental variables were the primary influencers of ARG reduction. Overall, this study offers a fresh perspective on the effects of vermicomposting and its potential to mitigate the spread of ARGs.

Accumulation of antibiotics in the environment: Have appropriate measures been taken to protect Canadian human and ecological health?

In Canada, every day, contaminants of emerging concern (CEC) are discharged from waste treatment facilities into freshwaters. CECs such as pharmaceutical active compounds (PhACs), personal care products (PCPs), per- and polyfluoroalkyl substances (PFAS), and microplastics are legally discharged from sewage treatment plants (STPs), water reclamation plants (WRPs), hospital wastewater treatment plants (HWWTPs), or other forms of wastewater treatment facilities (WWTFs). In 2006, the Government of Canada established the Chemicals Management Plan (CMP) to classify chemicals based on a risk-priority assessment, which ranked many CECs such as PhACs as being of low urgency, therefore permitting these substances to continue being released into the environment at unmonitored rates. The problem with ranking PhACs as a low priority is that CMP's risk management assessment overlooks the long-term environmental and synergistic effects of PhAC accumulation, such as the long-term risk of antibiotic CEC accumulation in the spread of antibiotic resistance genes. The goal of this review is to specifically investigate antibiotic CEC accumulation and associated environmental risks to human and environmental health, as well as to determine whether appropriate legislative strategies are in place within Canada's governance framework. In this research, secondary data on antibiotic CEC levels in Canadian and international wastewaters, their potential to promote antibiotic-resistant residues, associated environmental short- and long-term risks, and synergistic effects were all considered. Unlike similar past reviews, this review employed an interdisciplinary approach to propose new strategies from the perspectives of science, engineering, and law.

Quantitative assessment, molecular docking and novel metabolic pathways reveal the interaction mechanisms between norfloxacin biodegradation and environmental implications

Norfloxacin (NOR) is widely used in medicine and animal husbandry, but its accumulation in the environment poses a substantial threat to ecological and human health. Traditional physical, chemical, and rudimentary biological methods often fall short in mitigating NOR contamination, necessitating innovative biological approaches. This study proposes an engineered bacterial consortium found in marine sediment as a strategy to enhance NOR degradation through inter-strain co-metabolism of diverse substrates. Strategically supplementing the engineered bacterial consortium with exogenous carbon sources and metal ions boosted the activity of key degradation enzymes like laccase, manganese peroxidase, and dehydrogenase. Iron and amino acids demonstrated synergistic effects, resulting in a remarkable 70.8% reduction in NOR levels. The innovative application of molecular docking elucidated enzyme interactions with NOR, uncovering potential biodegradation mechanisms. Quantitative assessment reinforced the efficiency of NOR degradation within the engineered bacterial consortium. Four metabolic routes are herein proposed: acetylation, defluorination, ring scission, and hydroxylation. Notably, this study discloses distinctive, co-operative metabolic pathways for NOR degradation within the specific microbial community. These findings provide new ways of understanding and investigating the bioremediation potential of NOR contaminants, which may lead to the development of more sustainable and effective environmental management strategies.

Global WWTP Microbiome-based Integrative Information Platform: From experience to intelligence

Domestic and industrial wastewater treatment plants (WWTPs) are facing formidable challenges in effectively eliminating emerging pollutants and conventional nutrients. In microbiome engineering, two approaches have been developed: a top-down method focusing on domesticating seed microbiomes into engineered ones, and a bottom-up strategy that synthesizes engineered microbiomes from microbial isolates. However, these approaches face substantial hurdles that limit their real-world applicability in wastewater treatment engineering. Addressing this gap, we propose the creation of a Global WWTP Microbiome-based Integrative Information Platform, inspired by the untapped microbiome and engineering data from WWTPs and advancements in artificial intelligence (AI). This open platform integrates microbiome and engineering information globally and utilizes AI-driven tools for identifying seed microbiomes for new plants, providing technical upgrades for existing facilities, and deploying microbiomes for accidental pollution remediation. Beyond its practical applications, this platform has significant scientific and social value, supporting multidisciplinary research, documenting microbial evolution, advancing Wastewater-Based Epidemiology, and enhancing global resource sharing. Overall, the platform is expected to enhance WWTPs' performance in pollution control, safeguarding a harmonious and healthy future for human society and the natural environment.

Dynamics of antimicrobial resistance and susceptibility profile in full-scale hospital wastewater treatment plants

Drug resistance has become a matter of great concern, with many bacteria now resist multiple antibiotics. This study depicts the occurrence of antibiotic-resistant bacteria (ARB) and resistance patterns in five full-scale hospital wastewater treatment plants (WWTPs). Samples of raw influent wastewater, as well as pre- and post-disinfected effluents, were monitored for targeted ARB and resistance genes in September 2022 and February 2023. Shifts in resistance profiles of Escherichia coli, Pseudomonas aeruginosa, and Acinetobacter baumannii antimicrobial-resistant indicators in the treated effluent compared to that in the raw wastewater were also worked out. Ceftazidime (6.78 × 105 CFU/mL) and cefotaxime (6.14 × 105 CFU/mL) resistant species showed the highest concentrations followed by ciprofloxacin (6.29 × 104 CFU/mL), and gentamicin (4.88 × 104 CFU/mL), in raw influent respectively. WWTP-D employing a combination of biological treatment and coagulation/clarification for wastewater decontamination showed promising results for reducing ARB emissions from wastewater. Relationships between treated effluent quality parameters and ARB loadings showed that high BOD5 and nitrate levels were possibly contributing to the persistence and/or selection of ARBs in WWTPs. Furthermore, antimicrobial susceptibility tests of targeted species revealed dynamic shifts in resistance profiles through treatment processes, highlighting the potential for ARB and ARGs in hospital wastewater to persist or amplify during treatment.

Removal of Amoxicillin From Wastewater Onto Activated Carbon: Optimization of Analytical Parameters by Response Surface Methodology

Antibiotics are widely used in veterinary and human medicine, but these compounds, when released into the aquatic environment, present potential risks to living organisms. In the present study, the activated carbon (AC) used for their removals is characterized by FT-IR spectroscopy, BET analysis and Scanning Electron Microscopy (SEM) to determine the physicochemical characteristics. Response surface methodology (RSM) and Box-Behnken statistical design (BBD) were used to optimize important parameters including pH (2-12), temperature (20-45°C), and AC dose (0.05-0.20 g). The experimental data were analyzed by analysis of variance (ANOVA) and fitted to second-order polynomial using multiple regression analysis. The optimal conditions for maximum elimination of Amoxicillin (Amox) are (Dose: 0.124 g, pH 5.03 and 45°C) by applying the desirability function (df). A confirmation experiment was carried out to evaluate the accuracy of the optimization model and maximum removal efficiency (R = 89.999%) was obtained under the optimized conditions. Several error analysis equations were used to measure goodness of fit. Pareto analysis suggests the importance of the relative order of factors: pH > Temperature > AC dose in optimized situations. The equilibrium adsorption data of Amox on Activated Carbone were analyzed by Freundlich, Elovich, Temkin and Langmuir models. The latter gave the best correlation with qmax capacities of 142.85 mg/g (R2 = 0.999) at 25°C is removed from solution. The adsorption process is dominated by chemisorption and the kinetic model obeys a pseudo-second order model (R2 = 0.999).

Effects of four antibiotics on the photosynthetic light reactions in the green alga Chlorella pyrenoidosa

Antibiotics are ubiquitously present in aquatic environments, posing a serious ecological risk to aquatic ecosystems. However, the effects of antibiotics on the photosynthetic light reactions of freshwater algae and the underlying mechanisms are relatively less understood. In this study, the effects of 4 representative antibiotics (clarithromycin, enrofloxacin, tetracycline, and sulfamethazine) on a freshwater alga (Chlorella pyrenoidosa) and the associated mechanisms, primarily focusing on key regulators of the photosynthetic light reactions, were evaluated. Algae were exposed to different concentrations of clarithromycin (0.0-0.3 mg/L), enrofloxacin (0.0-30.0 mg/L), tetracycline (0.0-10.0 mg/L), and sulfamethazine (0.0-50.0 mg/L) for 7 days. The results showed that the 4 antibiotics inhibited the growth, the photosynthetic pigment contents, and the activity of antioxidant enzymes. In addition, exposure to clarithromycin caused a 118.4 % increase in malondialdehyde (MDA) levels at 0.3 mg/L. Furthermore, the transcripts of genes for the adenosine triphosphate (ATP) - dependent chloroplast proteases (ftsH and clpP), genes in photosystem II (psbA, psbB, and psbC), genes related to ATP synthase (atpA, atpB, and atpH), and petA (related to cytochrome b6/f complex) were altered by clarithromycin. This study contributes to a better understanding of the risk of antibiotics on primary producers in aquatic environment.

The influence of the phylum Planctomycetota in the environmental resistome

Antimicrobial resistance is one of the leading causes of death worldwide and research on this topic has been on the spotlight for a long time. More recently and in agreement with the One Health Approach, the focus has moved towards the environmental resistome. Members of the phylum Planctomycetota are ubiquitously present in the environment including in hotspots for antimicrobial resistance selection and dissemination. Furthermore, phenotypic broad-range resistance has been observed in diverse members of this phylum. Here we review the evidence available on antimicrobial resistance in the underexploited Planctomycetota and highlight key aspects for future studies.

Efficient removal of ciprofloxacin from aqueous solution using Zn-C battery derived graphene oxide enhanced by hydrogen bonding, electrostatic and π-π interaction

In this study, graphene oxide (GO) derived from waste Zinc-Carbon (Zn-C) batteries was proposed for the efficient removal of antibiotics from the aqueous solution. Ciprofloxacin (CIP) antibiotic was selected as a typical contaminants. GO was prepared via an economical and environment-friendly route by using carbon rods from waste Zn-C batteries as the precursor. Characterization techniques were applied to determine the properties of as prepared GO. Effects of pH, contact time, and adsorbent dose on the adsorption were explored, and an optimum condition was established. Adsorption equilibrium was established in just 20 min for maximum removal of CIP (99.0%) at pH 5.7 for the adsorbent dose of 20 mg L-1 and at the initial concentration of CIP 2.0 mg L-1. The rapid and efficient removal of CIP was greatly influenced by the electrostatic attractions, pi-pi interactions and hydrogen bonding on the surface and edge of GO which was also proved by density functional theory (DFT). Langmuir model showed the best fit among the isotherm models and the calculated maximum adsorption capacity (qm) was 419.62 mg g-1 at 30°C. The kinetic studies also revealed that the adsorption process followed the pseudo-second-order model. The endothermic and spontaneous nature of adsorption was evaluated in thermodynamic studies.

The fate of pharmaceuticals and personal care products (PPCPs) in sewer sediments:Adsorption triggering resistance gene proliferation

In recent years, large quantities of pharmaceuticals and personal care products (PPCPs) have been discharged into sewers, while the mechanisms of PPCPs enrichment in sewer sediments have rarely been revealed. In this study, three PPCPs (tetracycline, sulfamethoxazole, and triclocarban) were added consecutively over a 90-day experimental period to reveal the mechanisms of PPCPs enrichment and the transmission of resistance genes in sewer sediments. The results showed that tetracycline (TC) and triclocarban (TCC) have higher adsorption concentration in sediments compared to sulfamethoxazole (SMX). The absolute abundance of Tets and suls genes increased in sediments under PPCPs pressure. The increase in secretion of extracellular polymeric substances (EPS) and the loosening of the structure exposed a large number of hydrophobic functional groups, which promoted the adsorption of PPCPs. The absolute abundance of antibiotic resistance genes (ARGs), EPS and the content of PPCPs in sediments exhibited significant correlations. The enrichment of PPCPs in sediments was attributed to the accumulation of EPS, which led to the proliferation of ARGs. These findings contributed to further understanding of the fate of PPCPs in sewer sediments and opened a new perspective for consideration of controlling the proliferation of resistance genes.

The potential contribution of aquatic wildlife to antibiotic resistance dissemination in freshwater ecosystems: A review

Antibiotic resistance (AR) is one of the major health threats of our time. The presence of antibiotics in the environment and their continuous release from sewage treatment plants, chemical manufacturing plants and animal husbandry, agriculture and aquaculture, result in constant selection pressure on microbial organisms. This presence leads to the emergence, mobilization, horizontal gene transfer and a selection of antibiotic resistance genes, resistant bacteria and mobile genetic elements. Under these circumstances, aquatic wildlife is impacted in all compartments, including freshwater organisms with partially impermeable microbiota. In this narrative review, recent advancements in terms of occurrence of antibiotics and antibiotic resistance genes in sewage treatment plant effluents source compared to freshwater have been examined, occurrence of antibiotic resistance in wildlife, as well as experiments on antibiotic exposure. Based on this current state of knowledge, we propose the hypothesis that freshwater aquatic wildlife may play a crucial role in the dissemination of antibiotic resistance within the environment. Specifically, we suggest that organisms with high bacterial density tissues, which are partially isolated from the external environment, such as fishes and amphibians, could potentially be reservoirs and amplifiers of antibiotic resistance in the environment, potentially favoring the increase of the abundance of antibiotic resistance genes and resistant bacteria. Potential avenues for further research (trophic transfer, innovative exposure experiment) and action (biodiversity eco-engineering) are finally proposed.

Overlooked Activation Role of Sulfite in Accelerating Hydrated Electron Treatment of Perfluorosulfonates

Photoexcitation of sulfite (SO32-) is often used to generate hydrated electrons (eaq-) in processes to degrade perfluoroalkyl and polyfluoroalkyl substances (PFASs). Conventional consensus discourages the utilization of SO32- concentrations exceeding 10 mM for effective defluorination. This has hindered our understanding of SO32- chemistry beyond its electron photogeneration properties. In contrast, the radiation-chemical study presented here, directly producing eaq- through water radiolysis, suggests that SO32- plays a previously overlooked activation role in the defluorination. Quantitative 60Co gamma irradiation experiments indicate that the increased SO32- concentration from 0.1 to 1 M enhances the defluorination rate by a remarkable 15-fold, especially for short-chain perfluoroalkyl sulfonate (PFSA). Furthermore, during the treatment of long-chain PFSA (C8F17-SO3-) with a higher concentration of SO32-, the intermediates of C8H17-SO3- and C3F7-COO- were observed, which are absent without SO32-. These observations highlight that a higher concentration of SO32- facilitates both reaction pathways: chain shortening and H/F exchange. Pulse radiolysis measurements show that elevated SO32- concentrations accelerate the bimolecular reaction between eaq- and PFSA by 2 orders of magnitude. 19F NMR measurements and theoretical simulations reveal the noncovalent interactions between SO32- and F atoms, which exceptionally reduce the C-F bond dissociation energy by nearly 40%. As a result, our study offers a more effective strategy for degrading highly persistent PFSA contaminants.

Discovery of sulfonamide resistance genes in deep groundwater below Patna, India

Global usage of pharmaceuticals has led to the proliferation of bacteria that are resistant to antimicrobial treatments, creating a substantial public health challenge. Here, we investigate the emergence of sulfonamide resistance genes in groundwater and surface water in Patna, a rapidly developing city in Bihar, India. We report the first quantification of three sulfonamide resistance genes (sulI, sulII and sulIII) in groundwater (12-107 m in depth) in India. The mean relative abundance of gene copies was found to be sulI (2.4 × 10-2 copies/16S rRNA gene) > sulII (5.4 × 10-3 copies/16S rRNA gene) > sulIII (2.4 × 10-3 copies/16S rRNA gene) in groundwater (n = 15) and surface water (n = 3). A comparison between antimicrobial resistance (AMR) genes and wastewater indicators, particularly tryptophan:fulvic-like fluorescence, suggests that wastewater was associated with AMR gene prevalence. Urban drainage channels, containing hospital and domestic wastes, are likely a substantial source of antimicrobial resistance in groundwater and surface water, including the Ganges (Ganga) River. This study is a reference point for decision-makers in the fight against antimicrobial resistance because it quantifies and determines potential sources of AMR genes in Indian groundwater.

Simultaneous and on-line detection of organic and heavy metal components in water using a novel nebulization-assisted injection plasma ionization triple quadruple mass spectrometry instrument

BACKGROUND

The global release of organic and heavy metal components into natural water bodies is a major concern for the environment and human health. The assessment of water quality relies on analyzing organic and heavy metal components qualitatively and quantitatively. Real-time identification of organic and metal components in water systems requires different analytical techniques due to varying measurement requirements. Thus, on-line detecting both organic compounds and heavy metals in ambient water systems simultaneously using a single instrumentation setup presents a significant challenge.

RESULTS

In this study, an analytical technique of nebulization-assisted injection plasma ionization mass spectrometry (NI-PIMS) was developed. This novel method enables the simultaneous detection of heavy metals and organic compounds in water system with high sensitivity, which has been demonstrated by the limit of quantification (LOQ) values below 1.0 μg/L for the three sterols (Enrofloxacin, ciprofloxacin, and clenbuterol) and three heavy metals (Pb, Ba, and Cd). Moreover, the method was successfully applied to rapidly analyze real water samples from urban and rural areas in China. The analytical results are available in less than 0.5 min, and only a few microliters of sample are required for each analysis.

SIGNIFICANCE AND NOVELTY

As far as we know, this is the first report of on-line simultaneous analysis of organic compounds and heavy metals in a water system using a single mass spectrometry instrument. Compared to traditional methods, NI-PIMS demonstrates higher efficiency, sensitivity, no or lower sample preparation, and less sample consumption. The advancement and widespread use of this technology are expected to enhance the effectiveness of mass spectrometers, broaden the applications, and play an important role in complex sample analysis in fields such as atmospheric science, environmental science, and earth science.

Comparative study on electro-regeneration of antibiotic-laden activated carbons in reverse osmosis concentrate

Electro-regeneration is emerging as a new technique to regenerate spent carbon adsorbents through an electrochemical process. In this study, sequential adsorption and electro-regeneration of ciprofloxacin (CIP)-laden carbon were investigated using both pristine and iron (Fe)-doped F400 activated carbon in distilled, deionized (DI) water and reverse osmosis (RO) concentrate water. The impact of reactor flow rate and sequential adsorption/electro-regeneration cycles on the regeneration efficiency were also evaluated. The results indicate that the breakthrough points for both adsorbents in DI water, where 100 % of the CIP molecules were adsorbed, occurred at around 7,800 bed volumes (BVs). Conversely, electro-regeneration for both adsorbents, where 94 % of the CIP molecules were desorbed, took place at 380 BVs. The main distinction between the two activated carbons lies in the initial range of BVs (<400 BVs).Fe doping on F400 appears to enhance its surface selectivity for CIP uptake, which can easily diffuse into the meso/macropore regions of Fe-doped F400. In contrast, pristine F400, being highly microporous, necessitated more contact time to fill its high-energy sites, resulting in a higher affinity for CIP adsorption. Over the four sequential adsorption/electro-regeneration cycles in DI water, a similar regeneration efficiency was observed at 190 BVs. As the flow rate increased from 2 to 6 mL/min, the CIP uptake on pristine F400 decreased in DI water, calculating 138, 74 and 57 mg/g for flow rates of 2, 4, and 6 mL/min, respectively. When the RO concentrate water was compared with DI water, the pristine F400 quickly reached saturation due to pore blockage caused by organic matter in RO concentrate. During electro-regeneration, up to 100 % of adsorbed CIP molecules were desorbed at around 120 BVs in RO concentrate, which is 3X faster than DI water. The effectiveness of this technology can be enhanced by implementing continuous flow systems, thereby improving the overall efficiency of CIP removal in RO concentrate.

Wastewater surveillance of antibiotic resistance and class 1 integron-integrase genes: Potential impact of wastewater characteristics on genes profile

Antibiotic resistance (AR) is a major global health concern, but current surveillance efforts primarily focus on healthcare settings, leaving a lack of understanding about AR across all sectors of the One Health approach. To bridge this gap, wastewater surveillance provides a cost-effective and efficient method for monitoring AR within a population. In this study, we implemented a surveillance program by monitoring the wastewater effluent from two large-scale municipal treatment plants situated in Isfahan, a central region of Iran. These treatment plants covered distinct catchment regions and served a combined population about two million of residents. Furthermore, the effect of physicochemical and microbial characteristics of wastewater effluent including biological oxygen demand (BOD), chemical oxygen demand (COD), total suspended solids (TSS), temperature, total coliforms and Escherichia coli concentration on the abundance of ARGs (blaCTX-M, tetW, sul1, cmlA, and ermB) and class 1 integron-integrase gene (intI1) were investigated. Sul1 and blaCTX-M were the most and least abundant ARGs in the two WWTPs, respectively. Principal Component Analysis showed that in both of the WWTPs all ARGs and intI1 gene abundance were positively correlated with effluent temperature, but all other effluent characteristics (BOD, COD, TSS, total coliforms and E. coli) showed no significant correlation with ARGs abundance. Temperature could affect the performance of conventional activated sludge process, which in turn could affect the abundance of ARGs. The results of this study suggest that other factors than BOD, COD and TSS may affect the ARGs abundance. The predicted AR could lead to development of effective interventions and policies to combat AR in the clinical settings. However, further research is needed to determine the relationship between the AR in wastewater and clinical settings as well as the effect of other influential factors on ARGs abundance.

Using UV/peracetic acid as pretreatment for subsequent bio-treatment of antibiotic-containing wastewater treatment: Mitigating microbial inhibition and antibiotic resistance genes proliferation

UV/peracetic acid (PAA) treatment presents a promising approach for antibiotic removal, but its effects on microbial community and proliferation of antibiotic resistance genes (ARGs) during the subsequent bio-treatment remain unclear. Thus, we evaluated the effects of the UV/PAA on tetracycline (TTC) degradation, followed by introduction of the treated wastewater into the bio-treatment system to monitor changes in ARG expression and biodegradability. Results demonstrated effective TTC elimination by the UV/PAA system, with carbon-centered radicals playing a significant role. Crucially, the UV/PAA system not only eliminated antibacterial activity but also inhibited potential ARG host growth, thereby minimizing the emergence and dissemination of ARGs during subsequent bio-treatment. Additionally, the UV/PAA system efficiently removed multi-antibiotic resistant bacteria and ARGs from the bio-treatment effluent, preventing ARGs from being released into the environment. Hence, we propose a multi-barrier strategy for treating antibiotic-containing wastewater, integrating UV/PAA pre-treatment and post-disinfection with bio-treatment. The inhibition of ARGs transmission by the integrated system was verified through actual soil testing, confirming its effectiveness in preventing ARGs dissemination in the surrounding natural ecosystem. Overall, the UV/PAA treatment system offers a promising solution for tackling ARGs challenges by controlling ARGs proliferation at the source and minimizing their release at the end of the treatment process.

Occurrence, bioaccumulation, fate, and risk assessment of emerging pollutants in aquatic environments: A review

Significant concerns on a global scale have been raised in response to the potential adverse impacts of emerging pollutants (EPs) on aquatic creatures. We have carefully reviewed relevant research over the past 10 years. The study focuses on five typical EPs: pharmaceuticals and personal care products (PPCPs), per- and polyfluoroalkyl substances (PFASs), drinking water disinfection byproducts (DBPs), brominated flame retardants (BFRs), and microplastics (MPs). The presence of EPs in the global aquatic environment is source-dependent, with wastewater treatment plants being the main source of EPs. Multiple studies have consistently shown that the final destination of most EPs in the water environment is sludge and sediment. Simultaneously, a number of EPs, such as PFASs, MPs, and BFRs, have long-term environmental transport potential. Some EPs exhibit notable tendencies towards bioaccumulation and biomagnification, while others pose challenges in terms of their degradation within both biological and abiotic treatment processes. The results showed that, in most cases, the ecological risk of EPs in aquatic environments was low, possibly due to potential dilution and degradation. Future research topics should include adding EPs detection items for the aquatic environment, combining pollution, and updating prediction models.

Powdered activated carbon facilitated degradation of complex organic compounds and tetracycline in stressed anaerobic digestion systems

Tetracycline exerts an inhibitory effect on anaerobic digestion, inducing stressed microbial activities and even system failure. Continuous-flow reactors (CFRs) and sequencing batch reactors (SBRs) were employed along with the dosage of powdered activated carbon (PAC) to enhance tetracycline removal during anaerobic digestion of complex organic compounds. PAC increased the maximum methane production rate by 15.6% (CFRs) and 13.8% (SBRs), and tetracycline biodegradation by 24.4% (CFRs) and 19.2% (SBRs). CFRs showed higher tetracycline removal and methane production rates than SBRs. Geobacter was enriched in CFRs, where Methanothrix was enriched with the addition of PAC. Desulfomicrobium harbored abundant propionate degradation-related genes, significantly correlating with tetracycline removal. The genes encoding carbon dioxide reduction in Methanothrix along with the detection of Geobacter might indicate direct interspecies electron transfer for methanogenesis in CFRs and PAC-added reactors. The study offers new insights into anaerobic digestion under tetracycline-stressed conditions and strategies for optimizing tetracycline removal.

Recent Developments in Porphyrin-Based Metal-Organic Framework Materials for Water Remediation under Visible-Light Irradiation

Access to clean drinking water is a basic requirement, and eliminating pollutants from wastewater is important for saving water ecosystems. The porous structure and surface characteristics of metal-organic frameworks (MOFs) can function as a perfect scaffold for removing toxic compounds from wastewater. Porphyrins are promising building blocks for constructing MOFs. Porphyrin-based metal-organic frameworks (P-MOFs) have been fabricated using porphyrin ligands, metal clusters, or ions. These materials can harvest light from a wide region of the solar spectrum, and their framework morphology and physicochemical properties can be controlled by changing their peripheral subunits or metal ions. These porous crystalline materials have generated interest because of their distinctive characteristics, including large permanent porosity, interesting surface morphology, broad conformational diversity, high photostability, and semiconducting nature. This article discusses the recent progress and usefulness of P-MOFs. The fabrication procedures of P-MOFs are discussed, followed by the adsorptive and photocatalytic removal of contaminants from wastewater. The relationships between the geometries of P-MOFs and their light-harvesting and charge-transfer mechanisms for the photocatalytic degradation of pollutants are highlighted. Finally, some future perspectives and obstacles in the photodegradation usage of P-MOFs are discussed, along with feasible research directions to standardize efficient photocatalysts for improved photodegradation for water treatment.

Airborne antibiotic resistome and microbiome in pharmaceutical factories

Antimicrobial resistance is considered to be one of the biggest public health problems, and airborne transmission is an important but under-appreciated pathway for the spread of antibiotic resistance genes (ARGs) in the environment. Previous research has shown pharmaceutical factories to be a major source of ARGs and antibiotic resistant bacteria (ARB) in the surrounding receiving water and soil environments. Pharmaceutical factories are hotspots of antibiotic resistance, but the atmospheric transmission and its environmental risk remain more concerns. Here, we conducted a metagenomic investigation into the airborne microbiome and resistome in three pharmaceutical factories in China. Soil (average: 38.45%) and wastewater (average: 28.53%) were major contributors of airborne resistome. ARGs (vanR/vanS, blaOXA, and CfxA) conferring resistance to critically important clinically used antibiotics were identified in the air samples. The wastewater treatment area had significantly higher relative abundances of ARGs (average: 0.64 copies/16S rRNA). Approximately 28.2% of the detected airborne ARGs were found to be associated with plasmids, and this increased to about 50% in the wastewater treatment area. We have compiled a list of high-risk airborne ARGs found in pharmaceutical factories. Moreover, A total of 1,043 viral operational taxonomic units were identified and linked to 47 family-group taxa. Different CRISPR-Cas immune systems have been identified in bacterial hosts in response to phage infection. Similarly, higher phage abundance (average: 2451.70 PPM) was found in the air of the wastewater treatment area. Our data provide insights into the antibiotic resistance gene profiles and microbiome (bacterial and non-bacterial) in pharmaceutical factories and reveal the potential role of horizontal transfer in the spread of airborne ARGs, with implications for human and animal health.

Spatiotemporal distribution of ecological risk of antibiotics in seven major river basins of China: An optimized multilevel assessment approach

Antibiotics have been recognized as emerging pollutants due to their ecological and human health risks. This paper aims to enhance the ecological risk assessment (ERA) framework for antibiotics, to illustrate the distribution of these risks across different locations and seasons, and to identify the antibiotics that pose high ecological risk. This paper focuses on 52 antibiotics in seven major basins of China. Relying on the optimized approach of ERA and antibiotic monitoring data published from 2017 to 2021, the results of ERA are presented in multilevel. Across the study area, there are marked variations in the spatial distribution of antibiotics' ecological risks. The Huaihe River Basin, the Haihe River Basin, and the Liaohe River Basin are the top three in the ranking of present ecological risks. The research results also reveal significant differences in temporal variation, underscoring the need for increased attention during certain seasons. Ten antibiotics with high contribution rates to ecological risk are identified, which is an important reference to formulate an antibiotic control list. The multilevel results provided both risk values and their ubiquities across a broad study region, which is a powerful support for developing ecological risk management of antibiotics.

An evaluation of conventional and nature-based technologies for controlling antibiotic-resistant bacteria and antibiotic-resistant genes in wastewater treatment plants

Antibiotic resistance is a globally recognized health concern which leads to longer hospital stays, increased morbidity, increased mortality, and higher medical costs. Understanding how antibiotic resistance persists and exchanges in environmental systems like soil, water, and wastewater are critically important for understanding the emergence of pathogens with new resistance profiles and the subsequent exposure of people who indirectly/directly come in contact with these pathogens. There are concerns about the widespread application of prophylactic antibiotics in the clinical and agriculture sectors, as well as chemicals/detergents used in food and manufacturing industries, especially the quaternary ammonium compounds which have been found responsible for the generation of resistant genes in water and soil. The rates of horizontal gene transfer increase where there is a lack of proper water/wastewater infrastructure, high antibiotic manufacturing industries, or endpoint users - such as hospitals and intensive agriculture. Conventional wastewater treatment technologies are often inefficient in the reduction of ARB/ARGs and provide the perfect combination of conditions for the development of antibiotic resistance. The wastewater discharged from municipal facilities may therefore be enriched with bacterial communities/pathogens and provide a suitable environment (due to the presence of nutrients and other pollutants) to enhance the transfer of antibiotic resistance. However, facilities with tertiary treatment (either traditional/emerging technologies) provide higher rates of reduction. This review provides a synthesis of the current understanding of wastewater treatment and antibiotic resistance, examining the drivers that may accelerate their possible transmission to a different environment, and highlighting the need for tertiary technologies used in treatment plants for the reduction of resistant bacteria/genes.

Ecotoxicity of five veterinary antibiotics on indicator organisms and water and soil communities

This study explores the environmental effects of five common veterinary antibiotics widely detected in the environment, (chlortetracycline,CTC; oxytetracycline,OTC; florfenicol,FF; neomycin, NMC; and sulfadiazine, SDZ) on four bioindicators: Daphnia magna, Vibrio fischeri, Eisenia fetida, and Allium cepa, representing aquatic and soil environments. Additionally, microbial communities characterized through 16 S rRNA gene sequencing from a river and natural soil were exposed to the antibiotics to assess changes in population growth and metabolic profiles using Biolog EcoPlates™. Tetracyclines are harmful to Vibrio fisheri (LC50 ranges of 15-25 µg/mL), and the other three antibiotics seem to only affect D. magna, especially, SDZ. None of the antibiotics produced mortality in E. fetida at concentrations below 1000 mg/kg. NMC and CTC had the highest phytotoxicities in A. cepa (LC50 = 97-174 µg/mL, respectively). Antibiotics significantly reduced bacterial metabolism at 0.1-10 µg/mL. From the highest to the lowest toxicity on aquatic communities: OTC > FF > SDZ ≈ CTC > NMC and on edaphic communities: CTC ≈ OTC > FF > SDZ > NMC. In river communities, OTC and FF caused substantial decreases in bacterial metabolism at low concentrations (0.1 µg/mL), impacting carbohydrates, amino acids (OTC), and polymers (FF). At 10 µg/mL and above, OTC, CTC, and FF significantly decreased metabolizing all tested metabolites. In soil communities, a more pronounced decrease in metabolizing ability, detectable at 0.1 µg/mL, particularly affected amines/amides and carboxylic and ketonic acids (p < 0.05). These new ecotoxicity findings underscore that the concentrations of these antibiotics in the environment can significantly impact both aquatic and terrestrial ecosystems.

Nanoscale zero-valent iron alleviate antibiotic resistance risk during managed aquifer recharge (MAR) by regulating denitrifying bacterial network

The frequent occurrence of antibiotics in reclaimed water is concerning, in the case of managed aquifer recharge (MAR), it inevitably hinders further water purification and accelerates the evolutionary resistance in indigenous bacteria. In this study, we constructed two column reactors and nanoscale zero-valent iron (nZVI) amendment was applied for its effects on water quality variation, microbial community succession, and antibiotic resistance genes (ARGs) dissemination, deciphered the underlying mechanism of resistance risk reduction. Results showed that nZVI was oxidized to iron oxides in the sediment column, and total effluent iron concentration was within permissible limits. nZVI enhanced NO3--N removal by 15.5% through enriching denitrifying bacteria and genes, whereas made no effects on oxacillin (OXA) removal. In addition, nZVI exhibited a pivotal impact on ARGs and plasmids decreasing. Network analysis elucidated that the diversity and richness of ARG host declined with nZVI amendment. Denitrifying bacteria play a key role in suppressing horizontal gene transfer (HGT). The underlying mechanisms of inhibited HGT included the downregulated SOS response, the inhibited Type-Ⅳ secretion system and the weakened driving force. This study afforded vital insights into ARG spread control, providing a reference for future applications of nZVI in MAR.

Urbanization and land use regulate soil vulnerability to antibiotic contamination in urban green spaces

The presence of antibiotics in environment is an emerging concern because of their ubiquitous occurrence, adverse eco-toxicological effects, and promotion of widespread antibiotic resistance. Urban soil, which plays a noticeable role in human health, may be a reservoir of antibiotics because of intensive human disturbance. However, little is understood about the vulnerability of soil to antibiotic contamination in urban areas and the spatial-temporal characteristics of anthropogenic and environmental pressures. In this study, we developed a framework for the dynamic assessment of soil vulnerability to antibiotic contamination in urban green spaces, combining antibiotic release, exposure, and consequence layers. According to the results, soil vulnerability risks shown obvious spatial-temporal variation in urban areas. Areas at a high risk of antibiotic contamination were usually found in urban centers with high population densities and in seasons with low temperature and vegetation coverage. Quinolones (e.g., ofloxacin and norfloxacin) were priority antibiotics that posed the highest vulnerability risks, followed by tetracyclines. We also confirmed the effectiveness of the vulnerability assessment by correlating soil vulnerability indexes and antibiotic residues in urban soils. Furthermore, urbanization- and land use-related parameters were shown to be critical in regulating soil vulnerability to antibiotic contamination based on sensitivity analysis. These findings have important implications for the prediction and mitigation of urban soil contamination with antibiotics and strategies to improve human health.

Antibiotics and antibiotic resistance genes removal in biological aerated filter

Two laboratory-level biological aerated filters (BAF) were constructed to explore their treatment capacity for simulated antibiotic wastewater at high (1 - 16 mg/L) and low (0 - 0.5 mg/L) concentrations. Results showed that BAF was capable of removing both sulfonamides and tetracyclines with an efficiency of over 90 % at 16 mg/L. The main mechanism for removing antibiotics was found to be biodegradation followed by adsorption. Paenarthrobacter was identified as the key genus in sulfonamides degradation, while Hydrogenophaga played a crucial role in tetracyclines degradation. Antibiotics resistant genes such as intI1, sul1, sul2, tetA, tetW and tetX were frequently detected in the effluent, with interception rates ranging from 105 - 106 copies/mL. The dominated microorganisms obtained in the study could potentially be utilized to enhance the capacity of biological processes for treating antibiotics contaminated wastewater. These findings contribute to a better understanding of BAF treating wastewater containing antibiotics and resistant genes.

Efficient treatment of veterinary pharmaceutical industrial wastewater by catalytic ozonation process: degradation of enrofloxacin via molecular ozone reactions

The study focused on the efficacious performance of bimetallic Fe-Zn loaded 3A zeolite in catalytic ozonation for the degradation of highly toxic veterinary antibiotic enrofloxacin in wastewater of the pharmaceutical industry. Batch experiments were conducted in a glass reactor containing a submerged pump holding catalyst pellets at suction. The submerged pump provided the agitation and recirculation across the solution for effective contact with the catalyst. The effect of ozone flow (0.8-1.55 mg/min) and catalyst dose (5-15 g/L) on the enrofloxacin degradation and removal of other conventional pollutants COD, BOD5, turbidity was studied. In batch experiments, 10 g of Fe-Zn 3A zeolite efficiently removed 92% of enrofloxacin, 77% of COD, 69% BOD5, and 61% turbidity in 1 L sample of pharmaceutical wastewater in 30 min at 1.1 mg/min of O3 flow. The catalytic performance of Fe-Zn 3A zeolite notably exceeded the removal efficiencies of 52%, 51%, 52%, and 59% for enrofloxacin, COD, BOD5, and turbidity, respectively, achieved with single ozonation process. Furthermore, an increase in the biodegradability of treated pharmaceutical industrial wastewater was observed and made biodegradable easily for subsequent treatment.

Next-generation hybrid technologies for the treatment of pharmaceutical industry effluents

Water and industries are intangible units of the globe that are always set to meet the population's demand. The global population depends on one-third of freshwater increasing the demand. The increase in population along with urbanization has polluted the fresh water resources. The pharmaceutical industry is marked as an emerging contaminant of water pollution. The most common type of pharmaceutical drugs that are detected in the environment includes antibiotics, analgesics, NSAIDs, and pain-relieving drugs. These drugs alter the food chain of the organisms causing chaos mainly in the marine ecosystem. Pharmaceutical drugs are found only in shallow amounts (ng/mg) they have a huge impact on the living system. The consumption of water contaminated with pharmaceutical ingredients can disrupt reproduction, hormonal imbalance, cancer, and respiratory problems. Various methods are used to remove these chemicals from the environment. In this review, we mainly focused on the emerging hybrid technologies and their significance in the effective treatment of pharmaceutical wastewater. This review paper primarily elaborates on the merits and demerits of existing conventional technologies helpful in developing integrated technologies for the modern era of pharmaceutical effluent treatment. This review paper further in detail discusses the various strategies of eco-friendly bioremediation techniques namely biostimulation, bioaugmentation, bacterial degradation, mycoremediation, phytoremediation, and others for the ultimate removal of pharmaceutical contaminants in wastewater. The review makes clear that targeted and hybrid solutions are what the world will require in the future to get rid of these pharmacological prints.

Removal of selected sulfonamides and sulfonamide resistance genes from wastewater in full-scale constructed wetlands

Sulfonamides are high-consumption antibiotics that reach the aquatic environment. The threat related to their presence in wastewater and the environment is not only associated with their antibacterial properties, but also with risk of the spread of drug resistance in bacteria. Therefore, the aim of this work was to evaluate the occurrence of eight commonly used sulfonamides, sulfonamide resistance genes (sul1-3) and integrase genes intI1-3 in five full-scale constructed wetlands (CWs) differing in design (including hybrid systems) and in the source of wastewater (agricultural drainage, domestic sewage/surface runoff, and animal runs runoff in a zoo). The CWs were located in low-urbanized areas in Poland and in Czechia. No sulfonamides were detected in the CW treating agricultural tile drainage water. In the other four systems, four sulfonamide compounds were detected. Sulfamethoxazole exhibited the highest concentration in those four CWs and its highest was 12,603.23 ± 1000.66 ng/L in a CW treating a mixture of domestic sewage and surface runoff. Despite the high removal efficiencies of sulfamethoxazole in the tested CWs (86 %-99 %), it was still detected in the treated wastewater. The sul1 genes occurred in all samples of raw and treated wastewater and their abundance did not change significantly after the treatment process and it was, predominantly, at the level 105 gene copies numbers/mL. Noteworthy, sul2 genes were only found in the influents, and sul3 were not detected. The sulfonamides can be removed in CWs, but their elimination is not complete. However, hybrid CWs treating sewage were superior in decreasing the relative abundance of genes and the concentration of SMX. CWs may play a role in the dissemination of sulfonamide resistance genes of the sul1 type and other determinants of drug resistance, such as the intI1 gene, in the environment, however, the magnitude of this phenomenon is a matter of further research.

Environmental pitfalls and associated human health risks and ecological impacts from landfill leachate contaminants: Current evidence, recommended interventions and future directions

The improper management of solid waste, particularly the dumping of untreated municipal solid waste, poses a growing global challenge in both developed and developing nations. The generation of leachate is one of the significant issues that arise from this practice, and it can have harmful impacts on both the environment and public health. This paper presents an overview of the primary waste types that generate landfill leachate and their characteristics. This includes examining the distribution of waste types in landfills globally and how they have changed over time, which can provide valuable insights into potential pollutants in a given area and their trends. With a lack of specific regulations and growing concerns regarding environmental and health impacts, the paper also focuses on emerging contaminants. Furthermore, the environmental and ecological impacts of leachate, along with associated health risks, are analyzed. The potential applications of landfill leachate, suggested interventions and future directions are also discussed in the manuscript. Finally, this work addresses future research directions in landfill leachate studies, with attention, for the first time to the potentialities that artificial intelligence can offer for landfill leachate management, studies, and applications.

Effectiveness of wastewater treatment plant at the removal of nutrients, pathogenic bacteria, and antibiotic-resistant bacteria in wastewater from hospital source

This study is aimed at assessing the effectiveness of hospital's wastewater treatment plant (WWTP) in removing nutrients, pathogenic bacteria, and addressing antibiotic resistance using a case study of a tertiary hospital in Ibadan, Nigeria. During the dry and wet seasons in the month of July and December, respectively, samples were collected, and analyzed using standard guidelines to examine significant physicochemical parameters of the WTTP; to evaluate the removal efficiency of biological oxygen demand (BOD) and chemical oxygen demand (COD), and to examine the prevalence of pathogenic and antibiotic-resistant bacteria. The results of this study showed that during the dry season, certain parameters exceeded acceptable limits, including temperature, total suspended solids (TSS), total dissolved solids (TDS), phosphate, and nitrate. Although there were reductions in BOD (1555 mg/L to 482 mg/L) and COD levels (3160 mg/L to 972 mg/L), they remained above acceptable limits by World Health Organization. In the wet season, the level of COD (20 mg/L) in the effluent was within acceptable limit, while the BOD (160 mg/L) was above the acceptable limit. The WWTP effectively removed nutrients and reduced the microbial load, as evident from the absence of fecal coliforms in the effluent in both seasons. In respect to BOD removal efficiency, the level of purification of wastewater by the WWTP was 69% during the dry season, while the removal efficiency of COD was 83.54% which showed the efficiency of the WWTP at the removal of COD. However, antibiotic resistance was still present. The study concludes that while the WWTP effectively addressed nutrients and microbial load, additional measures such as tertiary treatment methods like chlorination and UV radiation are necessary to tackle antibiotic resistance. This is crucial to prevent the release of antibiotic-resistant bacteria into the environment, safeguarding human health, animals, plants, and overall environmental well-being.

Ozonation using a stainless-steel membrane contactor: Gas-liquid mass transfer and pharmaceuticals removal from secondary-treated municipal wastewater

A tubular porous stainless steel membrane contactor was characterized in terms of ozone-water mass transport, as well as its application in removing 23 pharmaceuticals (PhACs) detected in the secondary-treated municipal wastewater, under continuous mode operation. The volumetric mass transfer coefficient (KLa) was evaluated based on liquid flow rate, gas flow rate, and ozone gas concentration. The KLa values were substantially improved with an increment in liquid flow rate (1.6 times from 30 to 70 dm3 h-1) and gas flow rate (3.6 times from 0.30 to 0.85 Ndm3 min-1) due to the improved mixing in the gas-liquid interface. For the lowest liquid flow rate (30 dm3 h-1), the water phase boundary layer (82%) exhibited the major ozone transfer resistance, but it became almost comparable with membrane resistance for the highest liquid flow rate (70 dm3 h-1). Additionally, the influence of the specific ozone dose (0.39, 0.53, and 0.69 g O3 g DOC-1) and ozone inlet gas concentration ( [Formula: see text]  = 27, 80, and 134 g Nm-3) were investigated in the elimination of 23 PhACs found in secondary-treated municipal wastewater. An ozone dose of 0.69 g O3 g DOC-1 and residence time of 60 s resulted in the removal of 12 out of the 23 compounds over 80%, while 17 compounds were abated above 60%. The elimination of PhACs was strongly correlated with kinetic reaction constants values with ozone and hydroxyl radicals (kO3 and kHO•), leading to a characteristic elimination pattern for each group of contaminants. This study demonstrates the high potential of membrane contactors as an appealing alternative for ozone-driven wastewater treatment.